diff --git a/Documentation/devicetree/bindings/rtc/nvidia,tegra20-rtc.txt b/Documentation/devicetree/bindings/rtc/nvidia,tegra20-rtc.txt
new file mode 100644
index 0000000..93f45e9
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/nvidia,tegra20-rtc.txt
@@ -0,0 +1,19 @@
+NVIDIA Tegra20 real-time clock
+
+The Tegra RTC maintains seconds and milliseconds counters, and five alarm
+registers. The alarms and other interrupts may wake the system from low-power
+state.
+
+Required properties:
+
+- compatible : should be "nvidia,tegra20-rtc".
+- reg : Specifies base physical address and size of the registers.
+- interrupts : A single interrupt specifier.
+
+Example:
+
+timer {
+	compatible = "nvidia,tegra20-rtc";
+	reg = <0x7000e000 0x100>;
+	interrupts = <0 2 0x04>;
+};
diff --git a/Documentation/devicetree/bindings/timer/nvidia,tegra20-timer.txt b/Documentation/devicetree/bindings/timer/nvidia,tegra20-timer.txt
new file mode 100644
index 0000000..e019fdc
--- /dev/null
+++ b/Documentation/devicetree/bindings/timer/nvidia,tegra20-timer.txt
@@ -0,0 +1,21 @@
+NVIDIA Tegra20 timer
+
+The Tegra20 timer provides four 29-bit timer channels and a single 32-bit free
+running counter. The first two channels may also trigger a watchdog reset.
+
+Required properties:
+
+- compatible : should be "nvidia,tegra20-timer".
+- reg : Specifies base physical address and size of the registers.
+- interrupts : A list of 4 interrupts; one per timer channel.
+
+Example:
+
+timer {
+	compatible = "nvidia,tegra20-timer";
+	reg = <0x60005000 0x60>;
+	interrupts = <0 0 0x04
+			0 1 0x04
+			0 41 0x04
+			0 42 0x04>;
+};
diff --git a/Documentation/devicetree/bindings/timer/nvidia,tegra30-timer.txt b/Documentation/devicetree/bindings/timer/nvidia,tegra30-timer.txt
new file mode 100644
index 0000000..906109d
--- /dev/null
+++ b/Documentation/devicetree/bindings/timer/nvidia,tegra30-timer.txt
@@ -0,0 +1,23 @@
+NVIDIA Tegra30 timer
+
+The Tegra30 timer provides ten 29-bit timer channels, a single 32-bit free
+running counter, and 5 watchdog modules. The first two channels may also
+trigger a legacy watchdog reset.
+
+Required properties:
+
+- compatible : should be "nvidia,tegra30-timer", "nvidia,tegra20-timer".
+- reg : Specifies base physical address and size of the registers.
+- interrupts : A list of 6 interrupts; one per each of timer channels 1
+    through 5, and one for the shared interrupt for the remaining channels.
+
+timer {
+	compatible = "nvidia,tegra30-timer", "nvidia,tegra20-timer";
+	reg = <0x60005000 0x400>;
+	interrupts = <0 0 0x04
+		      0 1 0x04
+		      0 41 0x04
+		      0 42 0x04
+		      0 121 0x04
+		      0 122 0x04>;
+};
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 3bb60c8..2277f95 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -650,6 +650,7 @@
 	select HAVE_CLK
 	select HAVE_SMP
 	select MIGHT_HAVE_CACHE_L2X0
+	select SPARSE_IRQ
 	select USE_OF
 	help
 	  This enables support for NVIDIA Tegra based systems (Tegra APX,
@@ -891,6 +892,7 @@
 	select GENERIC_CLOCKEVENTS
 	select HAVE_SMP
 	select MIGHT_HAVE_CACHE_L2X0
+	select SPARSE_IRQ
 	help
 	  Support for ST-Ericsson's Ux500 architecture
 
@@ -905,6 +907,7 @@
 	select MIGHT_HAVE_CACHE_L2X0
 	select PINCTRL
 	select PINCTRL_STN8815
+	select SPARSE_IRQ
 	help
 	  Support for the Nomadik platform by ST-Ericsson
 
@@ -948,7 +951,7 @@
 	help
 	  Support for TI's OMAP platform (OMAP1/2/3/4).
 
-config ARCH_VT8500
+config ARCH_VT8500_SINGLE
 	bool "VIA/WonderMedia 85xx"
 	select ARCH_HAS_CPUFREQ
 	select ARCH_REQUIRE_GPIOLIB
@@ -958,22 +961,12 @@
 	select GENERIC_CLOCKEVENTS
 	select GENERIC_GPIO
 	select HAVE_CLK
+	select MULTI_IRQ_HANDLER
+	select SPARSE_IRQ
 	select USE_OF
 	help
 	  Support for VIA/WonderMedia VT8500/WM85xx System-on-Chip.
 
-config ARCH_ZYNQ
-	bool "Xilinx Zynq ARM Cortex A9 Platform"
-	select ARM_AMBA
-	select ARM_GIC
-	select COMMON_CLK
-	select CPU_V7
-	select GENERIC_CLOCKEVENTS
-	select ICST
-	select MIGHT_HAVE_CACHE_L2X0
-	select USE_OF
-	help
-	  Support for Xilinx Zynq ARM Cortex A9 Platform
 endchoice
 
 menu "Multiple platform selection"
@@ -1074,7 +1067,6 @@
 source "arch/arm/mach-netx/Kconfig"
 
 source "arch/arm/mach-nomadik/Kconfig"
-source "arch/arm/plat-nomadik/Kconfig"
 
 source "arch/arm/plat-omap/Kconfig"
 
@@ -1137,8 +1129,12 @@
 source "arch/arm/mach-vexpress/Kconfig"
 source "arch/arm/plat-versatile/Kconfig"
 
+source "arch/arm/mach-vt8500/Kconfig"
+
 source "arch/arm/mach-w90x900/Kconfig"
 
+source "arch/arm/mach-zynq/Kconfig"
+
 # Definitions to make life easier
 config ARCH_ACORN
 	bool
diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index 512b394..661030d 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -379,6 +379,13 @@
 		  Say Y here if you want kernel low-level debugging support
 		  on Allwinner A1X based platforms on the UART1.
 
+	config DEBUG_TEGRA_UART
+		depends on ARCH_TEGRA
+		bool "Use Tegra UART for low-level debug"
+		help
+		  Say Y here if you want kernel low-level debugging support
+		  on Tegra based platforms.
+
 	config DEBUG_VEXPRESS_UART0_DETECT
 		bool "Autodetect UART0 on Versatile Express Cortex-A core tiles"
 		depends on ARCH_VEXPRESS && CPU_CP15_MMU
@@ -452,6 +459,36 @@
 	  Choose UART port on which kernel low-level debug messages
 	  should be output.
 
+choice
+	prompt "Low-level debug console UART"
+	depends on DEBUG_LL && DEBUG_TEGRA_UART
+
+	config TEGRA_DEBUG_UART_AUTO_ODMDATA
+	bool "Via ODMDATA"
+	help
+	  Automatically determines which UART to use for low-level debug based
+	  on the ODMDATA value. This value is part of the BCT, and is written
+	  to the boot memory device using nvflash, or other flashing tool.
+	  When bits 19:18 are 3, then bits 17:15 indicate which UART to use;
+	  0/1/2/3/4 are UART A/B/C/D/E.
+
+	config TEGRA_DEBUG_UARTA
+		bool "UART A"
+
+	config TEGRA_DEBUG_UARTB
+		bool "UART B"
+
+	config TEGRA_DEBUG_UARTC
+		bool "UART C"
+
+	config TEGRA_DEBUG_UARTD
+		bool "UART D"
+
+	config TEGRA_DEBUG_UARTE
+		bool "UART E"
+
+endchoice
+
 config DEBUG_LL_INCLUDE
 	string
 	default "debug/icedcc.S" if DEBUG_ICEDCC
@@ -469,6 +506,8 @@
 	default "debug/sunxi.S" if DEBUG_SUNXI_UART0 || DEBUG_SUNXI_UART1
 	default "debug/vexpress.S" if DEBUG_VEXPRESS_UART0_DETECT || \
 		DEBUG_VEXPRESS_UART0_CA9 || DEBUG_VEXPRESS_UART0_RS1
+	default "debug/tegra.S" if DEBUG_TEGRA_UART
+	default "debug/zynq.S" if DEBUG_ZYNQ_UART0 || DEBUG_ZYNQ_UART1
 	default "mach/debug-macro.S"
 
 config EARLY_PRINTK
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index 9c60f47..30c443c 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -202,7 +202,6 @@
 plat-$(CONFIG_ARCH_OMAP)	+= omap
 plat-$(CONFIG_ARCH_S3C64XX)	+= samsung
 plat-$(CONFIG_PLAT_IOP)		+= iop
-plat-$(CONFIG_PLAT_NOMADIK)	+= nomadik
 plat-$(CONFIG_PLAT_ORION)	+= orion
 plat-$(CONFIG_PLAT_PXA)		+= pxa
 plat-$(CONFIG_PLAT_S3C24XX)	+= s3c24xx samsung
diff --git a/arch/arm/boot/dts/tegra20.dtsi b/arch/arm/boot/dts/tegra20.dtsi
index fba998e..b8effa1 100644
--- a/arch/arm/boot/dts/tegra20.dtsi
+++ b/arch/arm/boot/dts/tegra20.dtsi
@@ -91,6 +91,12 @@
 		};
 	};
 
+	timer@50004600 {
+		compatible = "arm,cortex-a9-twd-timer";
+		reg = <0x50040600 0x20>;
+		interrupts = <1 13 0x304>;
+	};
+
 	cache-controller@50043000 {
 		compatible = "arm,pl310-cache";
 		reg = <0x50043000 0x1000>;
@@ -108,6 +114,15 @@
 		#interrupt-cells = <3>;
 	};
 
+	timer@60005000 {
+		compatible = "nvidia,tegra20-timer";
+		reg = <0x60005000 0x60>;
+		interrupts = <0 0 0x04
+			      0 1 0x04
+			      0 41 0x04
+			      0 42 0x04>;
+	};
+
 	apbdma: dma {
 		compatible = "nvidia,tegra20-apbdma";
 		reg = <0x6000a000 0x1200>;
@@ -225,6 +240,12 @@
 		#pwm-cells = <2>;
 	};
 
+	rtc {
+		compatible = "nvidia,tegra20-rtc";
+		reg = <0x7000e000 0x100>;
+		interrupts = <0 2 0x04>;
+	};
+
 	i2c@7000c000 {
 		compatible = "nvidia,tegra20-i2c";
 		reg = <0x7000c000 0x100>;
diff --git a/arch/arm/boot/dts/tegra30.dtsi b/arch/arm/boot/dts/tegra30.dtsi
index efa603d..529fdb8 100644
--- a/arch/arm/boot/dts/tegra30.dtsi
+++ b/arch/arm/boot/dts/tegra30.dtsi
@@ -91,6 +91,12 @@
 		};
 	};
 
+	timer@50004600 {
+		compatible = "arm,cortex-a9-twd-timer";
+		reg = <0x50040600 0x20>;
+		interrupts = <1 13 0xf04>;
+	};
+
 	cache-controller@50043000 {
 		compatible = "arm,pl310-cache";
 		reg = <0x50043000 0x1000>;
@@ -108,6 +114,17 @@
 		#interrupt-cells = <3>;
 	};
 
+	timer@60005000 {
+		compatible = "nvidia,tegra30-timer", "nvidia,tegra20-timer";
+		reg = <0x60005000 0x400>;
+		interrupts = <0 0 0x04
+			      0 1 0x04
+			      0 41 0x04
+			      0 42 0x04
+			      0 121 0x04
+			      0 122 0x04>;
+	};
+
 	apbdma: dma {
 		compatible = "nvidia,tegra30-apbdma", "nvidia,tegra20-apbdma";
 		reg = <0x6000a000 0x1400>;
@@ -219,6 +236,12 @@
 		#pwm-cells = <2>;
 	};
 
+	rtc {
+		compatible = "nvidia,tegra30-rtc", "nvidia,tegra20-rtc";
+		reg = <0x7000e000 0x100>;
+		interrupts = <0 2 0x04>;
+	};
+
 	i2c@7000c000 {
 		compatible =  "nvidia,tegra30-i2c", "nvidia,tegra20-i2c";
 		reg = <0x7000c000 0x100>;
diff --git a/arch/arm/include/debug/tegra.S b/arch/arm/include/debug/tegra.S
new file mode 100644
index 0000000..883d7c2
--- /dev/null
+++ b/arch/arm/include/debug/tegra.S
@@ -0,0 +1,223 @@
+/*
+ * Copyright (C) 2010,2011 Google, Inc.
+ * Copyright (C) 2011-2012 NVIDIA CORPORATION. All Rights Reserved.
+ *
+ * Author:
+ *	Colin Cross <ccross@google.com>
+ *	Erik Gilling <konkers@google.com>
+ *	Doug Anderson <dianders@chromium.org>
+ *	Stephen Warren <swarren@nvidia.com>
+ *
+ * Portions based on mach-omap2's debug-macro.S
+ * Copyright (C) 1994-1999 Russell King
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/serial_reg.h>
+
+#define UART_SHIFT 2
+
+/* Physical addresses */
+#define TEGRA_CLK_RESET_BASE		0x60006000
+#define TEGRA_APB_MISC_BASE		0x70000000
+#define TEGRA_UARTA_BASE		0x70006000
+#define TEGRA_UARTB_BASE		0x70006040
+#define TEGRA_UARTC_BASE		0x70006200
+#define TEGRA_UARTD_BASE		0x70006300
+#define TEGRA_UARTE_BASE		0x70006400
+#define TEGRA_PMC_BASE			0x7000e400
+
+#define TEGRA_CLK_RST_DEVICES_L		(TEGRA_CLK_RESET_BASE + 0x04)
+#define TEGRA_CLK_RST_DEVICES_H		(TEGRA_CLK_RESET_BASE + 0x08)
+#define TEGRA_CLK_RST_DEVICES_U		(TEGRA_CLK_RESET_BASE + 0x0c)
+#define TEGRA_CLK_OUT_ENB_L		(TEGRA_CLK_RESET_BASE + 0x10)
+#define TEGRA_CLK_OUT_ENB_H		(TEGRA_CLK_RESET_BASE + 0x14)
+#define TEGRA_CLK_OUT_ENB_U		(TEGRA_CLK_RESET_BASE + 0x18)
+#define TEGRA_PMC_SCRATCH20		(TEGRA_PMC_BASE + 0xa0)
+#define TEGRA_APB_MISC_GP_HIDREV	(TEGRA_APB_MISC_BASE + 0x804)
+
+/*
+ * Must be 1MB-aligned since a 1MB mapping is used early on.
+ * Must not overlap with regions in mach-tegra/io.c:tegra_io_desc[].
+ */
+#define UART_VIRTUAL_BASE		0xfe100000
+
+#define checkuart(rp, rv, lhu, bit, uart) \
+		/* Load address of CLK_RST register */ \
+		movw	rp, #TEGRA_CLK_RST_DEVICES_##lhu & 0xffff ; \
+		movt	rp, #TEGRA_CLK_RST_DEVICES_##lhu >> 16 ; \
+		/* Load value from CLK_RST register */ \
+		ldr	rp, [rp, #0] ; \
+		/* Test UART's reset bit */ \
+		tst	rp, #(1 << bit) ; \
+		/* If set, can't use UART; jump to save no UART */ \
+		bne	90f ; \
+		/* Load address of CLK_OUT_ENB register */ \
+		movw	rp, #TEGRA_CLK_OUT_ENB_##lhu & 0xffff ; \
+		movt	rp, #TEGRA_CLK_OUT_ENB_##lhu >> 16 ; \
+		/* Load value from CLK_OUT_ENB register */ \
+		ldr	rp, [rp, #0] ; \
+		/* Test UART's clock enable bit */ \
+		tst	rp, #(1 << bit) ; \
+		/* If clear, can't use UART; jump to save no UART */ \
+		beq	90f ; \
+		/* Passed all tests, load address of UART registers */ \
+		movw	rp, #TEGRA_UART##uart##_BASE & 0xffff ; \
+		movt	rp, #TEGRA_UART##uart##_BASE >> 16 ; \
+		/* Jump to save UART address */ \
+		b 91f
+
+		.macro  addruart, rp, rv, tmp
+		adr	\rp, 99f		@ actual addr of 99f
+		ldr	\rv, [\rp]		@ linked addr is stored there
+		sub	\rv, \rv, \rp		@ offset between the two
+		ldr	\rp, [\rp, #4]		@ linked tegra_uart_config
+		sub	\tmp, \rp, \rv		@ actual tegra_uart_config
+		ldr	\rp, [\tmp]		@ Load tegra_uart_config
+		cmp	\rp, #1			@ needs initialization?
+		bne	100f			@ no; go load the addresses
+		mov	\rv, #0			@ yes; record init is done
+		str	\rv, [\tmp]
+
+#ifdef CONFIG_TEGRA_DEBUG_UART_AUTO_ODMDATA
+		/* Check ODMDATA */
+10:		movw	\rp, #TEGRA_PMC_SCRATCH20 & 0xffff
+		movt	\rp, #TEGRA_PMC_SCRATCH20 >> 16
+		ldr	\rp, [\rp, #0]		@ Load PMC_SCRATCH20
+		ubfx	\rv, \rp, #18, #2	@ 19:18 are console type
+		cmp	\rv, #2			@ 2 and 3 mean DCC, UART
+		beq	11f			@ some boards swap the meaning
+		cmp	\rv, #3			@ so accept either
+		bne	90f
+11:		ubfx	\rv, \rp, #15, #3	@ 17:15 are UART ID
+		cmp	\rv, #0			@ UART 0?
+		beq	20f
+		cmp	\rv, #1			@ UART 1?
+		beq	21f
+		cmp	\rv, #2			@ UART 2?
+		beq	22f
+		cmp	\rv, #3			@ UART 3?
+		beq	23f
+		cmp	\rv, #4			@ UART 4?
+		beq	24f
+		b	90f			@ invalid
+#endif
+
+#if defined(CONFIG_TEGRA_DEBUG_UARTA) || \
+    defined(CONFIG_TEGRA_DEBUG_UART_AUTO_ODMDATA)
+		/* Check UART A validity */
+20:		checkuart(\rp, \rv, L, 6, A)
+#endif
+
+#if defined(CONFIG_TEGRA_DEBUG_UARTB) || \
+    defined(CONFIG_TEGRA_DEBUG_UART_AUTO_ODMDATA)
+		/* Check UART B validity */
+21:		checkuart(\rp, \rv, L, 7, B)
+#endif
+
+#if defined(CONFIG_TEGRA_DEBUG_UARTC) || \
+    defined(CONFIG_TEGRA_DEBUG_UART_AUTO_ODMDATA)
+		/* Check UART C validity */
+22:		checkuart(\rp, \rv, H, 23, C)
+#endif
+
+#if defined(CONFIG_TEGRA_DEBUG_UARTD) || \
+    defined(CONFIG_TEGRA_DEBUG_UART_AUTO_ODMDATA)
+		/* Check UART D validity */
+23:		checkuart(\rp, \rv, U, 1, D)
+#endif
+
+#if defined(CONFIG_TEGRA_DEBUG_UARTE) || \
+    defined(CONFIG_TEGRA_DEBUG_UART_AUTO_ODMDATA)
+		/* Check UART E validity */
+24:
+		checkuart(\rp, \rv, U, 2, E)
+#endif
+
+		/* No valid UART found */
+90:		mov	\rp, #0
+		/* fall through */
+
+		/* Record whichever UART we chose */
+91:		str	\rp, [\tmp, #4]		@ Store in tegra_uart_phys
+		cmp	\rp, #0			@ Valid UART address?
+		bne	92f			@ Yes, go process it
+		str	\rp, [\tmp, #8]		@ Store 0 in tegra_uart_virt
+		b	100f			@ Done
+92:		and	\rv, \rp, #0xffffff	@ offset within 1MB section
+		add	\rv, \rv, #UART_VIRTUAL_BASE
+		str	\rv, [\tmp, #8]		@ Store in tegra_uart_virt
+		movw	\rv, #TEGRA_APB_MISC_GP_HIDREV & 0xffff
+		movt	\rv, #TEGRA_APB_MISC_GP_HIDREV >> 16
+		ldr	\rv, [\rv, #0]		@ Load HIDREV
+		ubfx	\rv, \rv, #8, #8	@ 15:8 are SoC version
+		cmp	\rv, #0x20		@ Tegra20?
+		moveq	\rv, #0x75		@ Tegra20 divisor
+		movne	\rv, #0xdd		@ Tegra30 divisor
+		str	\rv, [\tmp, #12]	@ Save divisor to scratch
+		/* uart[UART_LCR] = UART_LCR_WLEN8 | UART_LCR_DLAB; */
+		mov	\rv, #UART_LCR_WLEN8 | UART_LCR_DLAB
+		str	\rv, [\rp, #UART_LCR << UART_SHIFT]
+		/* uart[UART_DLL] = div & 0xff; */
+		ldr	\rv, [\tmp, #12]
+		and	\rv, \rv, #0xff
+		str	\rv, [\rp, #UART_DLL << UART_SHIFT]
+		/* uart[UART_DLM] = div >> 8; */
+		ldr	\rv, [\tmp, #12]
+		lsr	\rv, \rv, #8
+		str	\rv, [\rp, #UART_DLM << UART_SHIFT]
+		/* uart[UART_LCR] = UART_LCR_WLEN8; */
+		mov	\rv, #UART_LCR_WLEN8
+		str	\rv, [\rp, #UART_LCR << UART_SHIFT]
+		b	100f
+
+		.align
+99:		.word	.
+		.word	tegra_uart_config
+		.ltorg
+
+		/* Load previously selected UART address */
+100:		ldr	\rp, [\tmp, #4]		@ Load tegra_uart_phys
+		ldr	\rv, [\tmp, #8]		@ Load tegra_uart_virt
+		.endm
+
+/*
+ * Code below is swiped from <asm/hardware/debug-8250.S>, but add an extra
+ * check to make sure that the UART address is actually valid.
+ */
+
+		.macro	senduart, rd, rx
+		cmp	\rx, #0
+		strneb	\rd, [\rx, #UART_TX << UART_SHIFT]
+1001:
+		.endm
+
+		.macro	busyuart, rd, rx
+		cmp	\rx, #0
+		beq	1002f
+1001:		ldrb	\rd, [\rx, #UART_LSR << UART_SHIFT]
+		and	\rd, \rd, #UART_LSR_TEMT | UART_LSR_THRE
+		teq	\rd, #UART_LSR_TEMT | UART_LSR_THRE
+		bne	1001b
+1002:
+		.endm
+
+		.macro	waituart, rd, rx
+#ifdef FLOW_CONTROL
+		cmp	\rx, #0
+		beq	1002f
+1001:		ldrb	\rd, [\rx, #UART_MSR << UART_SHIFT]
+		tst	\rd, #UART_MSR_CTS
+		beq	1001b
+1002:
+#endif
+		.endm
diff --git a/arch/arm/mach-zynq/include/mach/debug-macro.S b/arch/arm/include/debug/zynq.S
similarity index 61%
rename from arch/arm/mach-zynq/include/mach/debug-macro.S
rename to arch/arm/include/debug/zynq.S
index 3ab0be1..f9aa974 100644
--- a/arch/arm/mach-zynq/include/mach/debug-macro.S
+++ b/arch/arm/include/debug/zynq.S
@@ -1,5 +1,4 @@
-/* arch/arm/mach-zynq/include/mach/debug-macro.S
- *
+/*
  * Debugging macro include header
  *
  *  Copyright (C) 2011 Xilinx
@@ -13,9 +12,25 @@
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  */
+#define UART_CR_OFFSET		0x00  /* Control Register [8:0] */
+#define UART_SR_OFFSET		0x2C  /* Channel Status [11:0] */
+#define UART_FIFO_OFFSET	0x30  /* FIFO [15:0] or [7:0] */
 
-#include <mach/zynq_soc.h>
-#include <mach/uart.h>
+#define UART_SR_TXFULL		0x00000010	/* TX FIFO full */
+#define UART_SR_TXEMPTY		0x00000008	/* TX FIFO empty */
+
+#define UART0_PHYS		0xE0000000
+#define UART1_PHYS		0xE0001000
+#define UART_SIZE		SZ_4K
+#define UART_VIRT		0xF0001000
+
+#if IS_ENABLED(CONFIG_DEBUG_ZYNQ_UART1)
+# define LL_UART_PADDR		UART1_PHYS
+#else
+# define LL_UART_PADDR		UART0_PHYS
+#endif
+
+#define LL_UART_VADDR		UART_VIRT
 
 		.macro	addruart, rp, rv, tmp
 		ldr	\rp, =LL_UART_PADDR	@ physical
diff --git a/arch/arm/mach-nomadik/Kconfig b/arch/arm/mach-nomadik/Kconfig
index c744946..706dc57 100644
--- a/arch/arm/mach-nomadik/Kconfig
+++ b/arch/arm/mach-nomadik/Kconfig
@@ -4,7 +4,7 @@
 
 config MACH_NOMADIK_8815NHK
 	bool "ST 8815 Nomadik Hardware Kit (evaluation board)"
-	select HAS_MTU
+	select CLKSRC_NOMADIK_MTU
 	select NOMADIK_8815
 
 endmenu
diff --git a/arch/arm/mach-nomadik/board-nhk8815.c b/arch/arm/mach-nomadik/board-nhk8815.c
index 22ef8a1..5ccdf53 100644
--- a/arch/arm/mach-nomadik/board-nhk8815.c
+++ b/arch/arm/mach-nomadik/board-nhk8815.c
@@ -25,18 +25,16 @@
 #include <linux/io.h>
 #include <linux/pinctrl/machine.h>
 #include <linux/platform_data/pinctrl-nomadik.h>
+#include <linux/platform_data/clocksource-nomadik-mtu.h>
+#include <linux/platform_data/mtd-nomadik-nand.h>
 #include <asm/hardware/vic.h>
 #include <asm/sizes.h>
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
-#include <asm/mach/irq.h>
 #include <asm/mach/flash.h>
 #include <asm/mach/time.h>
-
-#include <plat/mtu.h>
-
-#include <linux/platform_data/mtd-nomadik-nand.h>
 #include <mach/fsmc.h>
+#include <mach/irqs.h>
 
 #include "cpu-8815.h"
 
@@ -260,7 +258,7 @@
 	src_cr |= SRC_CR_INIT_VAL;
 	writel(src_cr, io_p2v(NOMADIK_SRC_BASE));
 
-	nmdk_timer_init(io_p2v(NOMADIK_MTU0_BASE));
+	nmdk_timer_init(io_p2v(NOMADIK_MTU0_BASE), IRQ_MTU0);
 }
 
 static struct sys_timer nomadik_timer = {
diff --git a/arch/arm/mach-nomadik/include/mach/irqs.h b/arch/arm/mach-nomadik/include/mach/irqs.h
index a118e615..b549d05 100644
--- a/arch/arm/mach-nomadik/include/mach/irqs.h
+++ b/arch/arm/mach-nomadik/include/mach/irqs.h
@@ -72,7 +72,7 @@
 #define NOMADIK_NR_GPIO			128 /* last 4 not wired to pins */
 #define NOMADIK_GPIO_TO_IRQ(gpio)	((gpio) + NOMADIK_GPIO_OFFSET)
 #define NOMADIK_IRQ_TO_GPIO(irq)	((irq) - NOMADIK_GPIO_OFFSET)
-#define NR_IRQS				NOMADIK_GPIO_TO_IRQ(NOMADIK_NR_GPIO)
+#define NOMADIK_NR_IRQS			NOMADIK_GPIO_TO_IRQ(NOMADIK_NR_GPIO)
 
 /* Following two are used by entry_macro.S, to access our dual-vic */
 #define VIC_REG_IRQSR0		0
diff --git a/arch/arm/mach-tegra/Kconfig b/arch/arm/mach-tegra/Kconfig
index 9ff6f6e..e426d1b 100644
--- a/arch/arm/mach-tegra/Kconfig
+++ b/arch/arm/mach-tegra/Kconfig
@@ -57,57 +57,6 @@
 	  which controls AHB bus master arbitration and some
 	  perfomance parameters(priority, prefech size).
 
-choice
-        prompt "Default low-level debug console UART"
-        default TEGRA_DEBUG_UART_NONE
-
-config TEGRA_DEBUG_UART_NONE
-        bool "None"
-
-config TEGRA_DEBUG_UARTA
-        bool "UART-A"
-
-config TEGRA_DEBUG_UARTB
-        bool "UART-B"
-
-config TEGRA_DEBUG_UARTC
-        bool "UART-C"
-
-config TEGRA_DEBUG_UARTD
-        bool "UART-D"
-
-config TEGRA_DEBUG_UARTE
-        bool "UART-E"
-
-endchoice
-
-choice
-	prompt "Automatic low-level debug console UART"
-	default TEGRA_DEBUG_UART_AUTO_NONE
-
-config TEGRA_DEBUG_UART_AUTO_NONE
-	bool "None"
-
-config TEGRA_DEBUG_UART_AUTO_ODMDATA
-	bool "Via ODMDATA"
-	help
-	  Automatically determines which UART to use for low-level debug based
-	  on the ODMDATA value. This value is part of the BCT, and is written
-	  to the boot memory device using nvflash, or other flashing tool.
-	  When bits 19:18 are 3, then bits 17:15 indicate which UART to use;
-	  0/1/2/3/4 are UART A/B/C/D/E.
-
-config TEGRA_DEBUG_UART_AUTO_SCRATCH
-	bool "Via UART scratch register"
-	help
-	  Automatically determines which UART to use for low-level debug based
-	  on the UART scratch register value. Some bootloaders put ASCII 'D'
-	  in this register when they initialize their own console UART output.
-	  Using this option allows the kernel to automatically pick the same
-	  UART.
-
-endchoice
-
 config TEGRA_EMC_SCALING_ENABLE
 	bool "Enable scaling the memory frequency"
 
diff --git a/arch/arm/mach-tegra/common.c b/arch/arm/mach-tegra/common.c
index 11a74db..0816562 100644
--- a/arch/arm/mach-tegra/common.c
+++ b/arch/arm/mach-tegra/common.c
@@ -45,14 +45,15 @@
  * kernel is loaded. The data is declared here rather than debug-macro.S so
  * that multiple inclusions of debug-macro.S point at the same data.
  */
-#define TEGRA_DEBUG_UART_OFFSET (TEGRA_DEBUG_UART_BASE & 0xFFFF)
-u32 tegra_uart_config[3] = {
+u32 tegra_uart_config[4] = {
 	/* Debug UART initialization required */
 	1,
 	/* Debug UART physical address */
-	(u32)(IO_APB_PHYS + TEGRA_DEBUG_UART_OFFSET),
+	0,
 	/* Debug UART virtual address */
-	(u32)(IO_APB_VIRT + TEGRA_DEBUG_UART_OFFSET),
+	0,
+	/* Scratch space for debug macro */
+	0,
 };
 
 #ifdef CONFIG_OF
diff --git a/arch/arm/mach-tegra/include/mach/debug-macro.S b/arch/arm/mach-tegra/include/mach/debug-macro.S
deleted file mode 100644
index 44ca7b1..0000000
--- a/arch/arm/mach-tegra/include/mach/debug-macro.S
+++ /dev/null
@@ -1,100 +0,0 @@
-/*
- * arch/arm/mach-tegra/include/mach/debug-macro.S
- *
- * Copyright (C) 2010,2011 Google, Inc.
- * Copyright (C) 2011-2012 NVIDIA CORPORATION. All Rights Reserved.
- *
- * Author:
- *	Colin Cross <ccross@google.com>
- *	Erik Gilling <konkers@google.com>
- *	Doug Anderson <dianders@chromium.org>
- *	Stephen Warren <swarren@nvidia.com>
- *
- * Portions based on mach-omap2's debug-macro.S
- * Copyright (C) 1994-1999 Russell King
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */
-
-#include <linux/serial_reg.h>
-
-#include "../../iomap.h"
-#include "../../irammap.h"
-
-		.macro  addruart, rp, rv, tmp
-		adr	\rp, 99f		@ actual addr of 99f
-		ldr	\rv, [\rp]		@ linked addr is stored there
-		sub	\rv, \rv, \rp		@ offset between the two
-		ldr	\rp, [\rp, #4]		@ linked tegra_uart_config
-		sub	\tmp, \rp, \rv		@ actual tegra_uart_config
-		ldr	\rp, [\tmp]		@ Load tegra_uart_config
-		cmp	\rp, #1			@ needs intitialization?
-		bne	100f			@ no; go load the addresses
-		mov	\rv, #0			@ yes; record init is done
-		str	\rv, [\tmp]
-		mov	\rp, #TEGRA_IRAM_BASE	@ See if cookie is in IRAM
-		ldr	\rv, [\rp, #TEGRA_IRAM_DEBUG_UART_OFFSET]
-		movw	\rp, #TEGRA_IRAM_DEBUG_UART_COOKIE & 0xffff
-		movt	\rp, #TEGRA_IRAM_DEBUG_UART_COOKIE >> 16
-		cmp	\rv, \rp		@ Cookie present?
-		bne	100f			@ No, use default UART
-		mov	\rp, #TEGRA_IRAM_BASE	@ Load UART address from IRAM
-		ldr	\rv, [\rp, #TEGRA_IRAM_DEBUG_UART_OFFSET + 4]
-		str	\rv, [\tmp, #4]		@ Store in tegra_uart_phys
-		sub	\rv, \rv, #IO_APB_PHYS	@ Calculate virt address
-		add	\rv, \rv, #IO_APB_VIRT
-		str	\rv, [\tmp, #8]		@ Store in tegra_uart_virt
-		b	100f
-
-		.align
-99:		.word	.
-		.word	tegra_uart_config
-		.ltorg
-
-100:		ldr	\rp, [\tmp, #4]		@ Load tegra_uart_phys
-		ldr	\rv, [\tmp, #8]		@ Load tegra_uart_virt
-		.endm
-
-#define UART_SHIFT 2
-
-/*
- * Code below is swiped from <asm/hardware/debug-8250.S>, but add an extra
- * check to make sure that we aren't in the CONFIG_TEGRA_DEBUG_UART_NONE case.
- * We use the fact that all 5 valid UART addresses all have something in the
- * 2nd-to-lowest byte.
- */
-
-		.macro	senduart, rd, rx
-		tst	\rx, #0x0000ff00
-		strneb	\rd, [\rx, #UART_TX << UART_SHIFT]
-1001:
-		.endm
-
-		.macro	busyuart, rd, rx
-		tst	\rx, #0x0000ff00
-		beq	1002f
-1001:		ldrb	\rd, [\rx, #UART_LSR << UART_SHIFT]
-		and	\rd, \rd, #UART_LSR_TEMT | UART_LSR_THRE
-		teq	\rd, #UART_LSR_TEMT | UART_LSR_THRE
-		bne	1001b
-1002:
-		.endm
-
-		.macro	waituart, rd, rx
-#ifdef FLOW_CONTROL
-		tst	\rx, #0x0000ff00
-		beq	1002f
-1001:		ldrb	\rd, [\rx, #UART_MSR << UART_SHIFT]
-		tst	\rd, #UART_MSR_CTS
-		beq	1001b
-1002:
-#endif
-		.endm
diff --git a/arch/arm/mach-tegra/include/mach/irqs.h b/arch/arm/mach-tegra/include/mach/irqs.h
deleted file mode 100644
index aad1a2c..0000000
--- a/arch/arm/mach-tegra/include/mach/irqs.h
+++ /dev/null
@@ -1,182 +0,0 @@
-/*
- * arch/arm/mach-tegra/include/mach/irqs.h
- *
- * Copyright (C) 2010 Google, Inc.
- *
- * Author:
- *	Colin Cross <ccross@google.com>
- *	Erik Gilling <konkers@google.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */
-
-#ifndef __MACH_TEGRA_IRQS_H
-#define __MACH_TEGRA_IRQS_H
-
-#define INT_GIC_BASE			0
-
-#define IRQ_LOCALTIMER                  29
-
-/* Primary Interrupt Controller */
-#define INT_PRI_BASE			(INT_GIC_BASE + 32)
-#define INT_TMR1			(INT_PRI_BASE + 0)
-#define INT_TMR2			(INT_PRI_BASE + 1)
-#define INT_RTC				(INT_PRI_BASE + 2)
-#define INT_I2S2			(INT_PRI_BASE + 3)
-#define INT_SHR_SEM_INBOX_IBF		(INT_PRI_BASE + 4)
-#define INT_SHR_SEM_INBOX_IBE		(INT_PRI_BASE + 5)
-#define INT_SHR_SEM_OUTBOX_IBF		(INT_PRI_BASE + 6)
-#define INT_SHR_SEM_OUTBOX_IBE		(INT_PRI_BASE + 7)
-#define INT_VDE_UCQ_ERROR		(INT_PRI_BASE + 8)
-#define INT_VDE_SYNC_TOKEN		(INT_PRI_BASE + 9)
-#define INT_VDE_BSE_V			(INT_PRI_BASE + 10)
-#define INT_VDE_BSE_A			(INT_PRI_BASE + 11)
-#define INT_VDE_SXE			(INT_PRI_BASE + 12)
-#define INT_I2S1			(INT_PRI_BASE + 13)
-#define INT_SDMMC1			(INT_PRI_BASE + 14)
-#define INT_SDMMC2			(INT_PRI_BASE + 15)
-#define INT_XIO				(INT_PRI_BASE + 16)
-#define INT_VDE				(INT_PRI_BASE + 17)
-#define INT_AVP_UCQ			(INT_PRI_BASE + 18)
-#define INT_SDMMC3			(INT_PRI_BASE + 19)
-#define INT_USB				(INT_PRI_BASE + 20)
-#define INT_USB2			(INT_PRI_BASE + 21)
-#define INT_PRI_RES_22			(INT_PRI_BASE + 22)
-#define INT_EIDE			(INT_PRI_BASE + 23)
-#define INT_NANDFLASH			(INT_PRI_BASE + 24)
-#define INT_VCP				(INT_PRI_BASE + 25)
-#define INT_APB_DMA			(INT_PRI_BASE + 26)
-#define INT_AHB_DMA			(INT_PRI_BASE + 27)
-#define INT_GNT_0			(INT_PRI_BASE + 28)
-#define INT_GNT_1			(INT_PRI_BASE + 29)
-#define INT_OWR				(INT_PRI_BASE + 30)
-#define INT_SDMMC4			(INT_PRI_BASE + 31)
-
-/* Secondary Interrupt Controller */
-#define INT_SEC_BASE			(INT_PRI_BASE + 32)
-#define INT_GPIO1			(INT_SEC_BASE + 0)
-#define INT_GPIO2			(INT_SEC_BASE + 1)
-#define INT_GPIO3			(INT_SEC_BASE + 2)
-#define INT_GPIO4			(INT_SEC_BASE + 3)
-#define INT_UARTA			(INT_SEC_BASE + 4)
-#define INT_UARTB			(INT_SEC_BASE + 5)
-#define INT_I2C				(INT_SEC_BASE + 6)
-#define INT_SPI				(INT_SEC_BASE + 7)
-#define INT_TWC				(INT_SEC_BASE + 8)
-#define INT_TMR3			(INT_SEC_BASE + 9)
-#define INT_TMR4			(INT_SEC_BASE + 10)
-#define INT_FLOW_RSM0			(INT_SEC_BASE + 11)
-#define INT_FLOW_RSM1			(INT_SEC_BASE + 12)
-#define INT_SPDIF			(INT_SEC_BASE + 13)
-#define INT_UARTC			(INT_SEC_BASE + 14)
-#define INT_MIPI			(INT_SEC_BASE + 15)
-#define INT_EVENTA			(INT_SEC_BASE + 16)
-#define INT_EVENTB			(INT_SEC_BASE + 17)
-#define INT_EVENTC			(INT_SEC_BASE + 18)
-#define INT_EVENTD			(INT_SEC_BASE + 19)
-#define INT_VFIR			(INT_SEC_BASE + 20)
-#define INT_DVC				(INT_SEC_BASE + 21)
-#define INT_SYS_STATS_MON		(INT_SEC_BASE + 22)
-#define INT_GPIO5			(INT_SEC_BASE + 23)
-#define INT_CPU0_PMU_INTR		(INT_SEC_BASE + 24)
-#define INT_CPU1_PMU_INTR		(INT_SEC_BASE + 25)
-#define INT_SEC_RES_26			(INT_SEC_BASE + 26)
-#define INT_S_LINK1			(INT_SEC_BASE + 27)
-#define INT_APB_DMA_COP			(INT_SEC_BASE + 28)
-#define INT_AHB_DMA_COP			(INT_SEC_BASE + 29)
-#define INT_DMA_TX			(INT_SEC_BASE + 30)
-#define INT_DMA_RX			(INT_SEC_BASE + 31)
-
-/* Tertiary Interrupt Controller */
-#define INT_TRI_BASE			(INT_SEC_BASE + 32)
-#define INT_HOST1X_COP_SYNCPT		(INT_TRI_BASE + 0)
-#define INT_HOST1X_MPCORE_SYNCPT	(INT_TRI_BASE + 1)
-#define INT_HOST1X_COP_GENERAL		(INT_TRI_BASE + 2)
-#define INT_HOST1X_MPCORE_GENERAL	(INT_TRI_BASE + 3)
-#define INT_MPE_GENERAL			(INT_TRI_BASE + 4)
-#define INT_VI_GENERAL			(INT_TRI_BASE + 5)
-#define INT_EPP_GENERAL			(INT_TRI_BASE + 6)
-#define INT_ISP_GENERAL			(INT_TRI_BASE + 7)
-#define INT_2D_GENERAL			(INT_TRI_BASE + 8)
-#define INT_DISPLAY_GENERAL		(INT_TRI_BASE + 9)
-#define INT_DISPLAY_B_GENERAL		(INT_TRI_BASE + 10)
-#define INT_HDMI			(INT_TRI_BASE + 11)
-#define INT_TVO_GENERAL			(INT_TRI_BASE + 12)
-#define INT_MC_GENERAL			(INT_TRI_BASE + 13)
-#define INT_EMC_GENERAL			(INT_TRI_BASE + 14)
-#define INT_TRI_RES_15			(INT_TRI_BASE + 15)
-#define INT_TRI_RES_16			(INT_TRI_BASE + 16)
-#define INT_AC97			(INT_TRI_BASE + 17)
-#define INT_SPI_2			(INT_TRI_BASE + 18)
-#define INT_SPI_3			(INT_TRI_BASE + 19)
-#define INT_I2C2			(INT_TRI_BASE + 20)
-#define INT_KBC				(INT_TRI_BASE + 21)
-#define INT_EXTERNAL_PMU		(INT_TRI_BASE + 22)
-#define INT_GPIO6			(INT_TRI_BASE + 23)
-#define INT_TVDAC			(INT_TRI_BASE + 24)
-#define INT_GPIO7			(INT_TRI_BASE + 25)
-#define INT_UARTD			(INT_TRI_BASE + 26)
-#define INT_UARTE			(INT_TRI_BASE + 27)
-#define INT_I2C3			(INT_TRI_BASE + 28)
-#define INT_SPI_4			(INT_TRI_BASE + 29)
-#define INT_TRI_RES_30			(INT_TRI_BASE + 30)
-#define INT_SW_RESERVED			(INT_TRI_BASE + 31)
-
-/* Quaternary Interrupt Controller */
-#define INT_QUAD_BASE			(INT_TRI_BASE + 32)
-#define INT_SNOR			(INT_QUAD_BASE + 0)
-#define INT_USB3			(INT_QUAD_BASE + 1)
-#define INT_PCIE_INTR			(INT_QUAD_BASE + 2)
-#define INT_PCIE_MSI			(INT_QUAD_BASE + 3)
-#define INT_QUAD_RES_4			(INT_QUAD_BASE + 4)
-#define INT_QUAD_RES_5			(INT_QUAD_BASE + 5)
-#define INT_QUAD_RES_6			(INT_QUAD_BASE + 6)
-#define INT_QUAD_RES_7			(INT_QUAD_BASE + 7)
-#define INT_APB_DMA_CH0			(INT_QUAD_BASE + 8)
-#define INT_APB_DMA_CH1			(INT_QUAD_BASE + 9)
-#define INT_APB_DMA_CH2			(INT_QUAD_BASE + 10)
-#define INT_APB_DMA_CH3			(INT_QUAD_BASE + 11)
-#define INT_APB_DMA_CH4			(INT_QUAD_BASE + 12)
-#define INT_APB_DMA_CH5			(INT_QUAD_BASE + 13)
-#define INT_APB_DMA_CH6			(INT_QUAD_BASE + 14)
-#define INT_APB_DMA_CH7			(INT_QUAD_BASE + 15)
-#define INT_APB_DMA_CH8			(INT_QUAD_BASE + 16)
-#define INT_APB_DMA_CH9			(INT_QUAD_BASE + 17)
-#define INT_APB_DMA_CH10		(INT_QUAD_BASE + 18)
-#define INT_APB_DMA_CH11		(INT_QUAD_BASE + 19)
-#define INT_APB_DMA_CH12		(INT_QUAD_BASE + 20)
-#define INT_APB_DMA_CH13		(INT_QUAD_BASE + 21)
-#define INT_APB_DMA_CH14		(INT_QUAD_BASE + 22)
-#define INT_APB_DMA_CH15		(INT_QUAD_BASE + 23)
-#define INT_QUAD_RES_24			(INT_QUAD_BASE + 24)
-#define INT_QUAD_RES_25			(INT_QUAD_BASE + 25)
-#define INT_QUAD_RES_26			(INT_QUAD_BASE + 26)
-#define INT_QUAD_RES_27			(INT_QUAD_BASE + 27)
-#define INT_QUAD_RES_28			(INT_QUAD_BASE + 28)
-#define INT_QUAD_RES_29			(INT_QUAD_BASE + 29)
-#define INT_QUAD_RES_30			(INT_QUAD_BASE + 30)
-#define INT_QUAD_RES_31			(INT_QUAD_BASE + 31)
-
-/* Tegra30 has 5 banks of 32 IRQs */
-#define INT_MAIN_NR			(32 * 5)
-#define INT_GPIO_BASE			(INT_PRI_BASE + INT_MAIN_NR)
-
-/* Tegra30 has 8 banks of 32 GPIOs */
-#define INT_GPIO_NR			(32 * 8)
-
-#define TEGRA_NR_IRQS			(INT_GPIO_BASE + INT_GPIO_NR)
-
-#define INT_BOARD_BASE			TEGRA_NR_IRQS
-#define NR_BOARD_IRQS			32
-
-#define NR_IRQS				(INT_BOARD_BASE + NR_BOARD_IRQS)
-
-#endif
diff --git a/arch/arm/mach-tegra/include/mach/uncompress.h b/arch/arm/mach-tegra/include/mach/uncompress.h
index 2772575..485003f 100644
--- a/arch/arm/mach-tegra/include/mach/uncompress.h
+++ b/arch/arm/mach-tegra/include/mach/uncompress.h
@@ -29,7 +29,6 @@
 #include <linux/serial_reg.h>
 
 #include "../../iomap.h"
-#include "../../irammap.h"
 
 #define BIT(x) (1 << (x))
 #define ARRAY_SIZE(arr) (sizeof(arr) / sizeof((arr)[0]))
@@ -52,17 +51,6 @@
 {
 }
 
-static inline void save_uart_address(void)
-{
-	u32 *buf = (u32 *)(TEGRA_IRAM_BASE + TEGRA_IRAM_DEBUG_UART_OFFSET);
-
-	if (uart) {
-		buf[0] = TEGRA_IRAM_DEBUG_UART_COOKIE;
-		buf[1] = (u32)uart;
-	} else
-		buf[0] = 0;
-}
-
 static const struct {
 	u32 base;
 	u32 reset_reg;
@@ -139,51 +127,19 @@
 }
 #endif
 
-#ifdef CONFIG_TEGRA_DEBUG_UART_AUTO_SCRATCH
-int auto_scratch(void)
-{
-	int i;
-
-	/*
-	 * Look for the first UART that:
-	 * a) Is not in reset.
-	 * b) Is clocked.
-	 * c) Has a 'D' in the scratchpad register.
-	 *
-	 * Note that on Tegra30, the first two conditions are required, since
-	 * if not true, accesses to the UART scratch register will hang.
-	 * Tegra20 doesn't have this issue.
-	 *
-	 * The intent is that the bootloader will tell the kernel which UART
-	 * to use by setting up those conditions. If nothing found, we'll fall
-	 * back to what's specified in TEGRA_DEBUG_UART_BASE.
-	 */
-	for (i = 0; i < ARRAY_SIZE(uarts); i++) {
-		if (!uart_clocked(i))
-			continue;
-
-		uart = (volatile u8 *)uarts[i].base;
-		if (uart[UART_SCR << DEBUG_UART_SHIFT] != 'D')
-			continue;
-
-		return i;
-	}
-
-	return -1;
-}
-#endif
-
 /*
  * Setup before decompression.  This is where we do UART selection for
  * earlyprintk and init the uart_base register.
  */
 static inline void arch_decomp_setup(void)
 {
-	int uart_id, auto_uart_id;
+	int uart_id;
 	volatile u32 *apb_misc = (volatile u32 *)TEGRA_APB_MISC_BASE;
 	u32 chip, div;
 
-#if defined(CONFIG_TEGRA_DEBUG_UARTA)
+#if defined(CONFIG_TEGRA_DEBUG_UART_AUTO_ODMDATA)
+	uart_id = auto_odmdata();
+#elif defined(CONFIG_TEGRA_DEBUG_UARTA)
 	uart_id = 0;
 #elif defined(CONFIG_TEGRA_DEBUG_UARTB)
 	uart_id = 1;
@@ -193,27 +149,14 @@
 	uart_id = 3;
 #elif defined(CONFIG_TEGRA_DEBUG_UARTE)
 	uart_id = 4;
-#else
-	uart_id = -1;
 #endif
 
-#if defined(CONFIG_TEGRA_DEBUG_UART_AUTO_ODMDATA)
-	auto_uart_id = auto_odmdata();
-#elif defined(CONFIG_TEGRA_DEBUG_UART_AUTO_SCRATCH)
-	auto_uart_id = auto_scratch();
-#else
-	auto_uart_id = -1;
-#endif
-	if (auto_uart_id != -1)
-		uart_id = auto_uart_id;
-
 	if (uart_id < 0 || uart_id >= ARRAY_SIZE(uarts) ||
 	    !uart_clocked(uart_id))
 		uart = NULL;
 	else
 		uart = (volatile u8 *)uarts[uart_id].base;
 
-	save_uart_address();
 	if (uart == NULL)
 		return;
 
diff --git a/arch/arm/mach-tegra/io.c b/arch/arm/mach-tegra/io.c
index 7d09f30..bb9c9c2 100644
--- a/arch/arm/mach-tegra/io.c
+++ b/arch/arm/mach-tegra/io.c
@@ -59,5 +59,6 @@
 
 void __init tegra_map_common_io(void)
 {
+	debug_ll_io_init();
 	iotable_init(tegra_io_desc, ARRAY_SIZE(tegra_io_desc));
 }
diff --git a/arch/arm/mach-tegra/iomap.h b/arch/arm/mach-tegra/iomap.h
index 5315103..db8be51 100644
--- a/arch/arm/mach-tegra/iomap.h
+++ b/arch/arm/mach-tegra/iomap.h
@@ -261,20 +261,6 @@
 #define TEGRA_SDMMC4_BASE		0xC8000600
 #define TEGRA_SDMMC4_SIZE		SZ_512
 
-#if defined(CONFIG_TEGRA_DEBUG_UART_NONE)
-# define TEGRA_DEBUG_UART_BASE 0
-#elif defined(CONFIG_TEGRA_DEBUG_UARTA)
-# define TEGRA_DEBUG_UART_BASE TEGRA_UARTA_BASE
-#elif defined(CONFIG_TEGRA_DEBUG_UARTB)
-# define TEGRA_DEBUG_UART_BASE TEGRA_UARTB_BASE
-#elif defined(CONFIG_TEGRA_DEBUG_UARTC)
-# define TEGRA_DEBUG_UART_BASE TEGRA_UARTC_BASE
-#elif defined(CONFIG_TEGRA_DEBUG_UARTD)
-# define TEGRA_DEBUG_UART_BASE TEGRA_UARTD_BASE
-#elif defined(CONFIG_TEGRA_DEBUG_UARTE)
-# define TEGRA_DEBUG_UART_BASE TEGRA_UARTE_BASE
-#endif
-
 /* On TEGRA, many peripherals are very closely packed in
  * two 256MB io windows (that actually only use about 64KB
  * at the start of each).
diff --git a/arch/arm/mach-tegra/irammap.h b/arch/arm/mach-tegra/irammap.h
index 0cbe632..501952a 100644
--- a/arch/arm/mach-tegra/irammap.h
+++ b/arch/arm/mach-tegra/irammap.h
@@ -23,13 +23,4 @@
 #define TEGRA_IRAM_RESET_HANDLER_OFFSET	0
 #define TEGRA_IRAM_RESET_HANDLER_SIZE	SZ_1K
 
-/*
- * These locations are written to by uncompress.h, and read by debug-macro.S.
- * The first word holds the cookie value if the data is valid. The second
- * word holds the UART physical address.
- */
-#define TEGRA_IRAM_DEBUG_UART_OFFSET	SZ_1K
-#define TEGRA_IRAM_DEBUG_UART_SIZE	8
-#define TEGRA_IRAM_DEBUG_UART_COOKIE	0x55415254
-
 #endif
diff --git a/arch/arm/mach-tegra/pcie.c b/arch/arm/mach-tegra/pcie.c
index f18fc3a..53d0858 100644
--- a/arch/arm/mach-tegra/pcie.c
+++ b/arch/arm/mach-tegra/pcie.c
@@ -43,6 +43,9 @@
 #include "board.h"
 #include "iomap.h"
 
+/* Hack - need to parse this from DT */
+#define INT_PCIE_INTR 130
+
 /* register definitions */
 #define AFI_OFFSET	0x3800
 #define PADS_OFFSET	0x3000
diff --git a/arch/arm/mach-tegra/timer.c b/arch/arm/mach-tegra/timer.c
index 6ff5035..e4863f3 100644
--- a/arch/arm/mach-tegra/timer.c
+++ b/arch/arm/mach-tegra/timer.c
@@ -26,16 +26,14 @@
 #include <linux/clocksource.h>
 #include <linux/clk.h>
 #include <linux/io.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
 
 #include <asm/mach/time.h>
 #include <asm/smp_twd.h>
 #include <asm/sched_clock.h>
 
-#include <mach/irqs.h>
-
 #include "board.h"
-#include "clock.h"
-#include "iomap.h"
 
 #define RTC_SECONDS            0x08
 #define RTC_SHADOW_SECONDS     0x0c
@@ -53,8 +51,8 @@
 #define TIMER_PTV 0x0
 #define TIMER_PCR 0x4
 
-static void __iomem *timer_reg_base = IO_ADDRESS(TEGRA_TMR1_BASE);
-static void __iomem *rtc_base = IO_ADDRESS(TEGRA_RTC_BASE);
+static void __iomem *timer_reg_base;
+static void __iomem *rtc_base;
 
 static struct timespec persistent_ts;
 static u64 persistent_ms, last_persistent_ms;
@@ -158,40 +156,66 @@
 	.flags		= IRQF_DISABLED | IRQF_TIMER | IRQF_TRIGGER_HIGH,
 	.handler	= tegra_timer_interrupt,
 	.dev_id		= &tegra_clockevent,
-	.irq		= INT_TMR3,
 };
 
-#ifdef CONFIG_HAVE_ARM_TWD
-static DEFINE_TWD_LOCAL_TIMER(twd_local_timer,
-			      TEGRA_ARM_PERIF_BASE + 0x600,
-			      IRQ_LOCALTIMER);
+static const struct of_device_id timer_match[] __initconst = {
+	{ .compatible = "nvidia,tegra20-timer" },
+	{}
+};
 
-static void __init tegra_twd_init(void)
-{
-	int err = twd_local_timer_register(&twd_local_timer);
-	if (err)
-		pr_err("twd_local_timer_register failed %d\n", err);
-}
-#else
-#define tegra_twd_init()	do {} while(0)
-#endif
+static const struct of_device_id rtc_match[] __initconst = {
+	{ .compatible = "nvidia,tegra20-rtc" },
+	{}
+};
 
 static void __init tegra_init_timer(void)
 {
+	struct device_node *np;
 	struct clk *clk;
 	unsigned long rate;
 	int ret;
 
+	np = of_find_matching_node(NULL, timer_match);
+	if (!np) {
+		pr_err("Failed to find timer DT node\n");
+		BUG();
+	}
+
+	timer_reg_base = of_iomap(np, 0);
+	if (!timer_reg_base) {
+		pr_err("Can't map timer registers");
+		BUG();
+	}
+
+	tegra_timer_irq.irq = irq_of_parse_and_map(np, 2);
+	if (tegra_timer_irq.irq <= 0) {
+		pr_err("Failed to map timer IRQ\n");
+		BUG();
+	}
+
 	clk = clk_get_sys("timer", NULL);
 	if (IS_ERR(clk)) {
-		pr_warn("Unable to get timer clock."
-			" Assuming 12Mhz input clock.\n");
+		pr_warn("Unable to get timer clock. Assuming 12Mhz input clock.\n");
 		rate = 12000000;
 	} else {
 		clk_prepare_enable(clk);
 		rate = clk_get_rate(clk);
 	}
 
+	of_node_put(np);
+
+	np = of_find_matching_node(NULL, rtc_match);
+	if (!np) {
+		pr_err("Failed to find RTC DT node\n");
+		BUG();
+	}
+
+	rtc_base = of_iomap(np, 0);
+	if (!rtc_base) {
+		pr_err("Can't map RTC registers");
+		BUG();
+	}
+
 	/*
 	 * rtc registers are used by read_persistent_clock, keep the rtc clock
 	 * enabled
@@ -202,6 +226,8 @@
 	else
 		clk_prepare_enable(clk);
 
+	of_node_put(np);
+
 	switch (rate) {
 	case 12000000:
 		timer_writel(0x000b, TIMERUS_USEC_CFG);
@@ -223,13 +249,13 @@
 
 	if (clocksource_mmio_init(timer_reg_base + TIMERUS_CNTR_1US,
 		"timer_us", 1000000, 300, 32, clocksource_mmio_readl_up)) {
-		printk(KERN_ERR "Failed to register clocksource\n");
+		pr_err("Failed to register clocksource\n");
 		BUG();
 	}
 
 	ret = setup_irq(tegra_timer_irq.irq, &tegra_timer_irq);
 	if (ret) {
-		printk(KERN_ERR "Failed to register timer IRQ: %d\n", ret);
+		pr_err("Failed to register timer IRQ: %d\n", ret);
 		BUG();
 	}
 
@@ -241,7 +267,9 @@
 	tegra_clockevent.cpumask = cpu_all_mask;
 	tegra_clockevent.irq = tegra_timer_irq.irq;
 	clockevents_register_device(&tegra_clockevent);
-	tegra_twd_init();
+#ifdef CONFIG_HAVE_ARM_TWD
+	twd_local_timer_of_register();
+#endif
 	register_persistent_clock(NULL, tegra_read_persistent_clock);
 }
 
diff --git a/arch/arm/mach-ux500/Kconfig b/arch/arm/mach-ux500/Kconfig
index e8c3f0d..5dea906 100644
--- a/arch/arm/mach-ux500/Kconfig
+++ b/arch/arm/mach-ux500/Kconfig
@@ -7,8 +7,8 @@
 	select ARM_ERRATA_764369 if SMP
 	select ARM_GIC
 	select CACHE_L2X0
+	select CLKSRC_NOMADIK_MTU
 	select COMMON_CLK
-	select HAS_MTU
 	select PINCTRL
 	select PINCTRL_NOMADIK
 	select PL310_ERRATA_753970 if CACHE_PL310
diff --git a/arch/arm/mach-ux500/board-mop500-audio.c b/arch/arm/mach-ux500/board-mop500-audio.c
index bde91a5..7209db7 100644
--- a/arch/arm/mach-ux500/board-mop500-audio.c
+++ b/arch/arm/mach-ux500/board-mop500-audio.c
@@ -8,8 +8,7 @@
 #include <linux/init.h>
 #include <linux/gpio.h>
 #include <linux/platform_data/pinctrl-nomadik.h>
-
-#include <plat/ste_dma40.h>
+#include <linux/platform_data/dma-ste-dma40.h>
 
 #include <mach/devices.h>
 #include <mach/hardware.h>
diff --git a/arch/arm/mach-ux500/board-mop500-sdi.c b/arch/arm/mach-ux500/board-mop500-sdi.c
index 9c8e4a9..051b62c 100644
--- a/arch/arm/mach-ux500/board-mop500-sdi.c
+++ b/arch/arm/mach-ux500/board-mop500-sdi.c
@@ -11,9 +11,9 @@
 #include <linux/amba/mmci.h>
 #include <linux/mmc/host.h>
 #include <linux/platform_device.h>
+#include <linux/platform_data/dma-ste-dma40.h>
 
 #include <asm/mach-types.h>
-#include <plat/ste_dma40.h>
 #include <mach/devices.h>
 #include <mach/hardware.h>
 
diff --git a/arch/arm/mach-ux500/board-mop500.c b/arch/arm/mach-ux500/board-mop500.c
index 5b70212..d453522 100644
--- a/arch/arm/mach-ux500/board-mop500.c
+++ b/arch/arm/mach-ux500/board-mop500.c
@@ -36,13 +36,12 @@
 #include <linux/leds.h>
 #include <linux/pinctrl/consumer.h>
 #include <linux/platform_data/pinctrl-nomadik.h>
+#include <linux/platform_data/dma-ste-dma40.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/hardware/gic.h>
 
-#include <plat/ste_dma40.h>
-
 #include <mach/hardware.h>
 #include <mach/setup.h>
 #include <mach/devices.h>
diff --git a/arch/arm/mach-ux500/cpu-db8500.c b/arch/arm/mach-ux500/cpu-db8500.c
index 93442fc..db0bb75 100644
--- a/arch/arm/mach-ux500/cpu-db8500.c
+++ b/arch/arm/mach-ux500/cpu-db8500.c
@@ -21,16 +21,19 @@
 #include <linux/of.h>
 #include <linux/of_platform.h>
 #include <linux/regulator/machine.h>
+#include <linux/platform_data/pinctrl-nomadik.h>
 #include <linux/random.h>
 
 #include <asm/pmu.h>
 #include <asm/mach/map.h>
 #include <asm/mach/arch.h>
 #include <asm/hardware/gic.h>
+
 #include <mach/hardware.h>
 #include <mach/setup.h>
 #include <mach/devices.h>
 #include <mach/db8500-regs.h>
+#include <mach/irqs.h>
 
 #include "devices-db8500.h"
 #include "ste-dma40-db8500.h"
diff --git a/arch/arm/mach-ux500/devices-common.c b/arch/arm/mach-ux500/devices-common.c
index 692a77a..16b5f71 100644
--- a/arch/arm/mach-ux500/devices-common.c
+++ b/arch/arm/mach-ux500/devices-common.c
@@ -14,6 +14,7 @@
 #include <linux/platform_data/pinctrl-nomadik.h>
 
 #include <mach/hardware.h>
+#include <mach/irqs.h>
 
 #include "devices-common.h"
 
diff --git a/arch/arm/mach-ux500/devices-db8500.c b/arch/arm/mach-ux500/devices-db8500.c
index 91754a8..318d490 100644
--- a/arch/arm/mach-ux500/devices-db8500.c
+++ b/arch/arm/mach-ux500/devices-db8500.c
@@ -12,11 +12,11 @@
 #include <linux/gpio.h>
 #include <linux/amba/bus.h>
 #include <linux/amba/pl022.h>
-
-#include <plat/ste_dma40.h>
+#include <linux/platform_data/dma-ste-dma40.h>
 
 #include <mach/hardware.h>
 #include <mach/setup.h>
+#include <mach/irqs.h>
 
 #include "ste-dma40-db8500.h"
 
diff --git a/arch/arm/mach-ux500/devices-db8500.h b/arch/arm/mach-ux500/devices-db8500.h
index 3c8010f..4b24c99 100644
--- a/arch/arm/mach-ux500/devices-db8500.h
+++ b/arch/arm/mach-ux500/devices-db8500.h
@@ -8,6 +8,7 @@
 #ifndef __DEVICES_DB8500_H
 #define __DEVICES_DB8500_H
 
+#include <mach/irqs.h>
 #include "devices-common.h"
 
 struct ske_keypad_platform_data;
diff --git a/arch/arm/mach-ux500/include/mach/irqs.h b/arch/arm/mach-ux500/include/mach/irqs.h
index e892854..fc77b42 100644
--- a/arch/arm/mach-ux500/include/mach/irqs.h
+++ b/arch/arm/mach-ux500/include/mach/irqs.h
@@ -46,6 +46,6 @@
 #include <mach/irqs-board-mop500.h>
 #endif
 
-#define NR_IRQS			IRQ_BOARD_END
+#define UX500_NR_IRQS		IRQ_BOARD_END
 
 #endif /* ASM_ARCH_IRQS_H */
diff --git a/arch/arm/mach-ux500/include/mach/msp.h b/arch/arm/mach-ux500/include/mach/msp.h
index 3cc7142..9991aea 100644
--- a/arch/arm/mach-ux500/include/mach/msp.h
+++ b/arch/arm/mach-ux500/include/mach/msp.h
@@ -8,7 +8,7 @@
 #ifndef __MSP_H
 #define __MSP_H
 
-#include <plat/ste_dma40.h>
+#include <linux/platform_data/dma-ste-dma40.h>
 
 enum msp_i2s_id {
 	MSP_I2S_0 = 0,
diff --git a/arch/arm/mach-ux500/timer.c b/arch/arm/mach-ux500/timer.c
index 6f39731..875309a 100644
--- a/arch/arm/mach-ux500/timer.c
+++ b/arch/arm/mach-ux500/timer.c
@@ -9,11 +9,10 @@
 #include <linux/clksrc-dbx500-prcmu.h>
 #include <linux/of.h>
 #include <linux/of_address.h>
+#include <linux/platform_data/clocksource-nomadik-mtu.h>
 
 #include <asm/smp_twd.h>
 
-#include <plat/mtu.h>
-
 #include <mach/setup.h>
 #include <mach/hardware.h>
 #include <mach/irqs.h>
@@ -96,7 +95,7 @@
 	 *
 	 */
 
-	nmdk_timer_init(mtu_timer_base);
+	nmdk_timer_init(mtu_timer_base, IRQ_MTU0);
 	clksrc_dbx500_prcmu_init(prcmu_timer_base);
 	ux500_twd_init();
 }
diff --git a/arch/arm/mach-ux500/usb.c b/arch/arm/mach-ux500/usb.c
index 145482e..78ac65f 100644
--- a/arch/arm/mach-ux500/usb.c
+++ b/arch/arm/mach-ux500/usb.c
@@ -7,10 +7,10 @@
 #include <linux/platform_device.h>
 #include <linux/usb/musb.h>
 #include <linux/dma-mapping.h>
-
-#include <plat/ste_dma40.h>
-#include <mach/hardware.h>
 #include <linux/platform_data/usb-musb-ux500.h>
+#include <linux/platform_data/dma-ste-dma40.h>
+
+#include <mach/hardware.h>
 
 #define MUSB_DMA40_RX_CH { \
 		.mode = STEDMA40_MODE_LOGICAL, \
diff --git a/arch/arm/mach-vt8500/Kconfig b/arch/arm/mach-vt8500/Kconfig
new file mode 100644
index 0000000..2ed0b7d
--- /dev/null
+++ b/arch/arm/mach-vt8500/Kconfig
@@ -0,0 +1,12 @@
+config ARCH_VT8500
+	bool "VIA/WonderMedia 85xx" if ARCH_MULTI_V5
+	default ARCH_VT8500_SINGLE
+	select ARCH_HAS_CPUFREQ
+	select ARCH_REQUIRE_GPIOLIB
+	select CLKDEV_LOOKUP
+	select CPU_ARM926T
+	select GENERIC_CLOCKEVENTS
+	select GENERIC_GPIO
+	select HAVE_CLK
+	help
+	  Support for VIA/WonderMedia VT8500/WM85xx System-on-Chip.
diff --git a/arch/arm/mach-vt8500/common.h b/arch/arm/mach-vt8500/common.h
index 2b24196..6f2b843 100644
--- a/arch/arm/mach-vt8500/common.h
+++ b/arch/arm/mach-vt8500/common.h
@@ -25,4 +25,7 @@
 /* defined in drivers/clk/clk-vt8500.c */
 void __init vtwm_clk_init(void __iomem *pmc_base);
 
+/* defined in irq.c */
+asmlinkage void vt8500_handle_irq(struct pt_regs *regs);
+
 #endif
diff --git a/arch/arm/mach-vt8500/include/mach/entry-macro.S b/arch/arm/mach-vt8500/include/mach/entry-macro.S
deleted file mode 100644
index 367d1b5..0000000
--- a/arch/arm/mach-vt8500/include/mach/entry-macro.S
+++ /dev/null
@@ -1,26 +0,0 @@
-/*
- * arch/arm/mach-vt8500/include/mach/entry-macro.S
- *
- * Low-level IRQ helper macros for VIA VT8500
- *
- * This file is licensed under  the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-	.macro  get_irqnr_preamble, base, tmp
-	@ physical 0xd8140000 is virtual 0xf8140000
-	mov	\base, #0xf8000000
-	orr	\base, \base, #0x00140000
-	.endm
-
-	.macro	get_irqnr_and_base, irqnr, irqstat, base, tmp
-	ldr	\irqnr, [\base]
-	cmp	\irqnr, #63 @ may be false positive, check interrupt status
-	bne	1001f
-	ldr	\irqstat, [\base, #0x84]
-	ands	\irqstat, #0x80000000
-	moveq	\irqnr, #0
-1001:
-	.endm
-
diff --git a/arch/arm/mach-vt8500/include/mach/irqs.h b/arch/arm/mach-vt8500/include/mach/irqs.h
deleted file mode 100644
index a129fd1..0000000
--- a/arch/arm/mach-vt8500/include/mach/irqs.h
+++ /dev/null
@@ -1,22 +0,0 @@
-/*
- *  arch/arm/mach-vt8500/include/mach/irqs.h
- *
- *  Copyright (C) 2010 Alexey Charkov <alchark@gmail.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-/* This value is just to make the core happy, never used otherwise */
-#define NR_IRQS 128
diff --git a/arch/arm/mach-vt8500/irq.c b/arch/arm/mach-vt8500/irq.c
index f8f9ab9..b9cf5ce 100644
--- a/arch/arm/mach-vt8500/irq.c
+++ b/arch/arm/mach-vt8500/irq.c
@@ -36,7 +36,7 @@
 #include <linux/of_address.h>
 
 #include <asm/irq.h>
-
+#include <asm/exception.h>
 
 #define VT8500_ICPC_IRQ		0x20
 #define VT8500_ICPC_FIQ		0x24
@@ -66,30 +66,34 @@
 #define VT8500_EDGE		( VT8500_TRIGGER_RISING \
 				| VT8500_TRIGGER_FALLING)
 
-static int irq_cnt;
+/* vt8500 has 1 intc, wm8505 and wm8650 have 2 */
+#define VT8500_INTC_MAX		2
 
-struct vt8500_irq_priv {
-	void __iomem *base;
+struct vt8500_irq_data {
+	void __iomem 		*base;		/* IO Memory base address */
+	struct irq_domain	*domain;	/* Domain for this controller */
 };
 
+/* Global variable for accessing io-mem addresses */
+static struct vt8500_irq_data intc[VT8500_INTC_MAX];
+static u32 active_cnt = 0;
+
 static void vt8500_irq_mask(struct irq_data *d)
 {
-	struct vt8500_irq_priv *priv =
-			(struct vt8500_irq_priv *)(d->domain->host_data);
+	struct vt8500_irq_data *priv = d->domain->host_data;
 	void __iomem *base = priv->base;
-	u8 edge;
+	void __iomem *stat_reg = base + VT8500_ICIS + (d->hwirq < 32 ? 0 : 4);
+	u8 edge, dctr;
+	u32 status;
 
 	edge = readb(base + VT8500_ICDC + d->hwirq) & VT8500_EDGE;
 	if (edge) {
-		void __iomem *stat_reg = base + VT8500_ICIS
-						+ (d->hwirq < 32 ? 0 : 4);
-		unsigned status = readl(stat_reg);
+		status = readl(stat_reg);
 
 		status |= (1 << (d->hwirq & 0x1f));
 		writel(status, stat_reg);
 	} else {
-		u8 dctr = readb(base + VT8500_ICDC + d->hwirq);
-
+		dctr = readb(base + VT8500_ICDC + d->hwirq);
 		dctr &= ~VT8500_INT_ENABLE;
 		writeb(dctr, base + VT8500_ICDC + d->hwirq);
 	}
@@ -97,8 +101,7 @@
 
 static void vt8500_irq_unmask(struct irq_data *d)
 {
-	struct vt8500_irq_priv *priv =
-			(struct vt8500_irq_priv *)(d->domain->host_data);
+	struct vt8500_irq_data *priv = d->domain->host_data;
 	void __iomem *base = priv->base;
 	u8 dctr;
 
@@ -109,8 +112,7 @@
 
 static int vt8500_irq_set_type(struct irq_data *d, unsigned int flow_type)
 {
-	struct vt8500_irq_priv *priv =
-			(struct vt8500_irq_priv *)(d->domain->host_data);
+	struct vt8500_irq_data *priv = d->domain->host_data;
 	void __iomem *base = priv->base;
 	u8 dctr;
 
@@ -148,17 +150,15 @@
 
 static void __init vt8500_init_irq_hw(void __iomem *base)
 {
-	unsigned int i;
+	u32 i;
 
 	/* Enable rotating priority for IRQ */
 	writel(ICPC_ROTATE, base + VT8500_ICPC_IRQ);
 	writel(0x00, base + VT8500_ICPC_FIQ);
 
-	for (i = 0; i < 64; i++) {
-		/* Disable all interrupts and route them to IRQ */
-		writeb(VT8500_INT_DISABLE | ICDC_IRQ,
-						base + VT8500_ICDC + i);
-	}
+	/* Disable all interrupts and route them to IRQ */
+	for (i = 0; i < 64; i++)
+		writeb(VT8500_INT_DISABLE | ICDC_IRQ, base + VT8500_ICDC + i);
 }
 
 static int vt8500_irq_map(struct irq_domain *h, unsigned int virq,
@@ -175,33 +175,67 @@
 	.xlate = irq_domain_xlate_onecell,
 };
 
+asmlinkage void __exception_irq_entry vt8500_handle_irq(struct pt_regs *regs)
+{
+	u32 stat, i;
+	int irqnr, virq;
+	void __iomem *base;
+
+	/* Loop through each active controller */
+	for (i=0; i<active_cnt; i++) {
+		base = intc[i].base;
+		irqnr = readl_relaxed(base) & 0x3F;
+		/*
+		  Highest Priority register default = 63, so check that this
+		  is a real interrupt by checking the status register
+		*/
+		if (irqnr == 63) {
+			stat = readl_relaxed(base + VT8500_ICIS + 4);
+			if (!(stat & BIT(31)))
+				continue;
+		}
+
+		virq = irq_find_mapping(intc[i].domain, irqnr);
+		handle_IRQ(virq, regs);
+	}
+}
+
 int __init vt8500_irq_init(struct device_node *node, struct device_node *parent)
 {
-	struct irq_domain *vt8500_irq_domain;
-	struct vt8500_irq_priv *priv;
 	int irq, i;
 	struct device_node *np = node;
 
-	priv = kzalloc(sizeof(struct vt8500_irq_priv), GFP_KERNEL);
-	priv->base = of_iomap(np, 0);
+	if (active_cnt == VT8500_INTC_MAX) {
+		pr_err("%s: Interrupt controllers > VT8500_INTC_MAX\n",
+								__func__);
+		goto out;
+	}
 
-	vt8500_irq_domain = irq_domain_add_legacy(node, 64, irq_cnt, 0,
-				&vt8500_irq_domain_ops, priv);
-	if (!vt8500_irq_domain)
-		pr_err("%s: Unable to add wmt irq domain!\n", __func__);
+	intc[active_cnt].base = of_iomap(np, 0);
+	intc[active_cnt].domain = irq_domain_add_linear(node, 64,
+			&vt8500_irq_domain_ops,	&intc[active_cnt]);
 
-	irq_set_default_host(vt8500_irq_domain);
+	if (!intc[active_cnt].base) {
+		pr_err("%s: Unable to map IO memory\n", __func__);
+		goto out;
+	}
 
-	vt8500_init_irq_hw(priv->base);
+	if (!intc[active_cnt].domain) {
+		pr_err("%s: Unable to add irq domain!\n", __func__);
+		goto out;
+	}
 
-	pr_info("Added IRQ Controller @ %x [virq_base = %d]\n",
-						(u32)(priv->base), irq_cnt);
+	vt8500_init_irq_hw(intc[active_cnt].base);
+
+	pr_info("vt8500-irq: Added interrupt controller\n");
+
+	active_cnt++;
 
 	/* check if this is a slaved controller */
 	if (of_irq_count(np) != 0) {
 		/* check that we have the correct number of interrupts */
 		if (of_irq_count(np) != 8) {
-			pr_err("%s: Incorrect IRQ map for slave controller\n",
+			pr_err("%s: Incorrect IRQ map for slaved controller\n",
 					__func__);
 			return -EINVAL;
 		}
@@ -213,9 +247,7 @@
 
 		pr_info("vt8500-irq: Enabled slave->parent interrupts\n");
 	}
-
-	irq_cnt += 64;
-
+out:
 	return 0;
 }
 
diff --git a/arch/arm/mach-vt8500/vt8500.c b/arch/arm/mach-vt8500/vt8500.c
index a5bd286..3c66d48 100644
--- a/arch/arm/mach-vt8500/vt8500.c
+++ b/arch/arm/mach-vt8500/vt8500.c
@@ -192,5 +192,6 @@
 	.timer		= &vt8500_timer,
 	.init_machine	= vt8500_init,
 	.restart	= vt8500_restart,
+	.handle_irq	= vt8500_handle_irq,
 MACHINE_END
 
diff --git a/arch/arm/mach-zynq/Kconfig b/arch/arm/mach-zynq/Kconfig
new file mode 100644
index 0000000..adb6c0e
--- /dev/null
+++ b/arch/arm/mach-zynq/Kconfig
@@ -0,0 +1,13 @@
+config ARCH_ZYNQ
+	bool "Xilinx Zynq ARM Cortex A9 Platform" if ARCH_MULTI_V7
+	select ARM_AMBA
+	select ARM_GIC
+	select COMMON_CLK
+	select CPU_V7
+	select GENERIC_CLOCKEVENTS
+	select ICST
+	select MIGHT_HAVE_CACHE_L2X0
+	select USE_OF
+	select SPARSE_IRQ
+	help
+	  Support for Xilinx Zynq ARM Cortex A9 Platform
diff --git a/arch/arm/mach-zynq/common.c b/arch/arm/mach-zynq/common.c
index 79bf5fb..e16d4be 100644
--- a/arch/arm/mach-zynq/common.c
+++ b/arch/arm/mach-zynq/common.c
@@ -30,10 +30,10 @@
 #include <asm/mach/time.h>
 #include <asm/mach-types.h>
 #include <asm/page.h>
+#include <asm/pgtable.h>
 #include <asm/hardware/gic.h>
 #include <asm/hardware/cache-l2x0.h>
 
-#include <mach/zynq_soc.h>
 #include "common.h"
 
 static struct of_device_id zynq_of_bus_ids[] __initdata = {
@@ -68,32 +68,15 @@
 	of_irq_init(irq_match);
 }
 
-/* The minimum devices needed to be mapped before the VM system is up and
- * running include the GIC, UART and Timer Counter.
- */
+#define SCU_PERIPH_PHYS		0xF8F00000
+#define SCU_PERIPH_SIZE		SZ_8K
+#define SCU_PERIPH_VIRT		(VMALLOC_END - SCU_PERIPH_SIZE)
 
-static struct map_desc io_desc[] __initdata = {
-	{
-		.virtual	= TTC0_VIRT,
-		.pfn		= __phys_to_pfn(TTC0_PHYS),
-		.length		= TTC0_SIZE,
-		.type		= MT_DEVICE,
-	}, {
-		.virtual	= SCU_PERIPH_VIRT,
-		.pfn		= __phys_to_pfn(SCU_PERIPH_PHYS),
-		.length		= SCU_PERIPH_SIZE,
-		.type		= MT_DEVICE,
-	},
-
-#ifdef CONFIG_DEBUG_LL
-	{
-		.virtual	= LL_UART_VADDR,
-		.pfn		= __phys_to_pfn(LL_UART_PADDR),
-		.length		= UART_SIZE,
-		.type		= MT_DEVICE,
-	},
-#endif
-
+static struct map_desc scu_desc __initdata = {
+	.virtual	= SCU_PERIPH_VIRT,
+	.pfn		= __phys_to_pfn(SCU_PERIPH_PHYS),
+	.length		= SCU_PERIPH_SIZE,
+	.type		= MT_DEVICE,
 };
 
 static void __init xilinx_zynq_timer_init(void)
@@ -122,7 +105,8 @@
  */
 static void __init xilinx_map_io(void)
 {
-	iotable_init(io_desc, ARRAY_SIZE(io_desc));
+	debug_ll_io_init();
+	iotable_init(&scu_desc, 1);
 }
 
 static const char *xilinx_dt_match[] = {
diff --git a/arch/arm/mach-zynq/include/mach/hardware.h b/arch/arm/mach-zynq/include/mach/hardware.h
deleted file mode 100644
index d558d8a..0000000
--- a/arch/arm/mach-zynq/include/mach/hardware.h
+++ /dev/null
@@ -1,18 +0,0 @@
-/* arch/arm/mach-zynq/include/mach/hardware.h
- *
- *  Copyright (C) 2011 Xilinx
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-#ifndef __MACH_HARDWARE_H__
-#define __MACH_HARDWARE_H__
-
-#endif
diff --git a/arch/arm/mach-zynq/include/mach/irqs.h b/arch/arm/mach-zynq/include/mach/irqs.h
deleted file mode 100644
index 5fb04fd..0000000
--- a/arch/arm/mach-zynq/include/mach/irqs.h
+++ /dev/null
@@ -1,21 +0,0 @@
-/* arch/arm/mach-zynq/include/mach/irqs.h
- *
- *  Copyright (C) 2011 Xilinx
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-#ifndef __MACH_IRQS_H
-#define __MACH_IRQS_H
-
-#define ARCH_NR_GPIOS	118
-#define NR_IRQS		(128 + ARCH_NR_GPIOS)
-
-#endif
diff --git a/arch/arm/mach-zynq/include/mach/timex.h b/arch/arm/mach-zynq/include/mach/timex.h
deleted file mode 100644
index 6c0245e..0000000
--- a/arch/arm/mach-zynq/include/mach/timex.h
+++ /dev/null
@@ -1,23 +0,0 @@
-/* arch/arm/mach-zynq/include/mach/timex.h
- *
- *  Copyright (C) 2011 Xilinx
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-#ifndef __MACH_TIMEX_H__
-#define __MACH_TIMEX_H__
-
-/* the following is needed for the system to build but will be removed
-   in the future, the value is not important but won't hurt
-*/
-#define CLOCK_TICK_RATE	(100 * HZ)
-
-#endif
diff --git a/arch/arm/mach-zynq/include/mach/uart.h b/arch/arm/mach-zynq/include/mach/uart.h
deleted file mode 100644
index 5c47c97..0000000
--- a/arch/arm/mach-zynq/include/mach/uart.h
+++ /dev/null
@@ -1,25 +0,0 @@
-/* arch/arm/mach-zynq/include/mach/uart.h
- *
- *  Copyright (C) 2011 Xilinx
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-#ifndef __MACH_UART_H__
-#define __MACH_UART_H__
-
-#define UART_CR_OFFSET		0x00  /* Control Register [8:0] */
-#define UART_SR_OFFSET		0x2C  /* Channel Status [11:0] */
-#define UART_FIFO_OFFSET	0x30  /* FIFO [15:0] or [7:0] */
-
-#define UART_SR_TXFULL		0x00000010	/* TX FIFO full */
-#define UART_SR_TXEMPTY		0x00000008	/* TX FIFO empty */
-
-#endif
diff --git a/arch/arm/mach-zynq/include/mach/uncompress.h b/arch/arm/mach-zynq/include/mach/uncompress.h
deleted file mode 100644
index af4e844..0000000
--- a/arch/arm/mach-zynq/include/mach/uncompress.h
+++ /dev/null
@@ -1,51 +0,0 @@
-/* arch/arm/mach-zynq/include/mach/uncompress.h
- *
- *  Copyright (C) 2011 Xilinx
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-#ifndef __MACH_UNCOMPRESS_H__
-#define __MACH_UNCOMPRESS_H__
-
-#include <linux/io.h>
-#include <asm/processor.h>
-#include <mach/zynq_soc.h>
-#include <mach/uart.h>
-
-void arch_decomp_setup(void)
-{
-}
-
-static inline void flush(void)
-{
-	/*
-	 * Wait while the FIFO is not empty
-	 */
-	while (!(__raw_readl(IOMEM(LL_UART_PADDR + UART_SR_OFFSET)) &
-		UART_SR_TXEMPTY))
-		cpu_relax();
-}
-
-#define arch_decomp_wdog()
-
-static void putc(char ch)
-{
-	/*
-	 * Wait for room in the FIFO, then write the char into the FIFO
-	 */
-	while (__raw_readl(IOMEM(LL_UART_PADDR + UART_SR_OFFSET)) &
-		UART_SR_TXFULL)
-		cpu_relax();
-
-	__raw_writel(ch, IOMEM(LL_UART_PADDR + UART_FIFO_OFFSET));
-}
-
-#endif
diff --git a/arch/arm/mach-zynq/include/mach/zynq_soc.h b/arch/arm/mach-zynq/include/mach/zynq_soc.h
deleted file mode 100644
index 5ebbd8e..0000000
--- a/arch/arm/mach-zynq/include/mach/zynq_soc.h
+++ /dev/null
@@ -1,53 +0,0 @@
-/* arch/arm/mach-zynq/include/mach/zynq_soc.h
- *
- *  Copyright (C) 2011 Xilinx
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-#ifndef __MACH_XILINX_SOC_H__
-#define __MACH_XILINX_SOC_H__
-
-#include <asm/pgtable.h>
-
-#define PERIPHERAL_CLOCK_RATE		2500000
-
-/* Static peripheral mappings are mapped at the top of the vmalloc region.  The
- * early uart mapping causes intermediate problems/failure at certain
- * addresses, including the very top of the vmalloc region.  Map it at an
- * address that is known to work.
- */
-#define UART0_PHYS		0xE0000000
-#define UART1_PHYS		0xE0001000
-#define UART_SIZE		SZ_4K
-#define UART_VIRT		0xF0001000
-
-#define TTC0_PHYS		0xF8001000
-#define TTC0_SIZE		SZ_4K
-#define TTC0_VIRT		(VMALLOC_END - TTC0_SIZE)
-
-#define SCU_PERIPH_PHYS		0xF8F00000
-#define SCU_PERIPH_SIZE		SZ_8K
-#define SCU_PERIPH_VIRT		(TTC0_VIRT - SCU_PERIPH_SIZE)
-
-#if IS_ENABLED(CONFIG_DEBUG_ZYNQ_UART1)
-# define LL_UART_PADDR		UART1_PHYS
-#else
-# define LL_UART_PADDR		UART0_PHYS
-#endif
-
-#define LL_UART_VADDR		UART_VIRT
-
-/* The following are intended for the devices that are mapped early */
-
-#define TTC0_BASE			IOMEM(TTC0_VIRT)
-#define SCU_PERIPH_BASE			IOMEM(SCU_PERIPH_VIRT)
-
-#endif
diff --git a/arch/arm/mach-zynq/timer.c b/arch/arm/mach-zynq/timer.c
index 9662306..de3df28 100644
--- a/arch/arm/mach-zynq/timer.c
+++ b/arch/arm/mach-zynq/timer.c
@@ -29,7 +29,6 @@
 #include <linux/slab.h>
 #include <linux/clk-provider.h>
 
-#include <mach/zynq_soc.h>
 #include "common.h"
 
 /*
diff --git a/arch/arm/plat-nomadik/Kconfig b/arch/arm/plat-nomadik/Kconfig
deleted file mode 100644
index 19f55ca..0000000
--- a/arch/arm/plat-nomadik/Kconfig
+++ /dev/null
@@ -1,29 +0,0 @@
-# We keep common IP's here for Nomadik and other similar
-# familiy of processors from ST-Ericsson. At the moment we have
-# just MTU, others to follow soon.
-
-config PLAT_NOMADIK
-	bool
-	depends on ARCH_NOMADIK || ARCH_U8500
-	default y
-	select CLKSRC_MMIO
-	help
-	  Common platform code for Nomadik and other ST-Ericsson
-	  platforms.
-
-if PLAT_NOMADIK
-
-config HAS_MTU
-	bool
-	help
-	  Support for Multi Timer Unit. MTU provides access
-	  to multiple interrupt generating programmable
-	  32-bit free running decrementing counters.
-
-config NOMADIK_MTU_SCHED_CLOCK
-	bool
-	depends on HAS_MTU
-	help
-	  Use the Multi Timer Unit as the sched_clock.
-
-endif
diff --git a/arch/arm/plat-nomadik/Makefile b/arch/arm/plat-nomadik/Makefile
deleted file mode 100644
index 37c7cdd..0000000
--- a/arch/arm/plat-nomadik/Makefile
+++ /dev/null
@@ -1,5 +0,0 @@
-# arch/arm/plat-nomadik/Makefile
-# Copyright 2009 ST-Ericsson
-# Licensed under GPLv2
-
-obj-$(CONFIG_HAS_MTU)	+= timer.o
diff --git a/drivers/char/hw_random/Kconfig b/drivers/char/hw_random/Kconfig
index c58ea9b..c5a0262 100644
--- a/drivers/char/hw_random/Kconfig
+++ b/drivers/char/hw_random/Kconfig
@@ -216,7 +216,7 @@
 
 config HW_RANDOM_NOMADIK
 	tristate "ST-Ericsson Nomadik Random Number Generator support"
-	depends on HW_RANDOM && PLAT_NOMADIK
+	depends on HW_RANDOM && ARCH_NOMADIK
 	---help---
 	  This driver provides kernel-side support for the Random Number
 	  Generator hardware found on ST-Ericsson SoCs (8815 and 8500).
diff --git a/drivers/clk/ux500/u8500_clk.c b/drivers/clk/ux500/u8500_clk.c
index 7d0e025..6b889a0 100644
--- a/drivers/clk/ux500/u8500_clk.c
+++ b/drivers/clk/ux500/u8500_clk.c
@@ -12,7 +12,7 @@
 #include <linux/clk-provider.h>
 #include <linux/mfd/dbx500-prcmu.h>
 #include <linux/platform_data/clk-ux500.h>
-
+#include <mach/db8500-regs.h>
 #include "clk.h"
 
 void u8500_clk_init(void)
@@ -160,12 +160,6 @@
 	clk = clk_reg_prcmu_gate("uiccclk", NULL, PRCMU_UICCCLK, CLK_IS_ROOT);
 	clk_register_clkdev(clk, NULL, "uicc");
 
-	/*
-	 * FIXME: The MTU clocks might need some kind of "parent muxed join"
-	 * and these have no K-clocks. For now, we ignore the missing
-	 * connection to the corresponding P-clocks, p6_mtu0_clk and
-	 * p6_mtu1_clk. Instead timclk is used which is the valid parent.
-	 */
 	clk = clk_reg_prcmu_gate("timclk", NULL, PRCMU_TIMCLK, CLK_IS_ROOT);
 	clk_register_clkdev(clk, NULL, "mtu0");
 	clk_register_clkdev(clk, NULL, "mtu1");
@@ -405,8 +399,11 @@
 
 	clk = clk_reg_prcc_pclk("p6_pclk6", "per6clk", U8500_CLKRST6_BASE,
 				BIT(6), 0);
+	clk_register_clkdev(clk, "apb_pclk", "mtu0");
+
 	clk = clk_reg_prcc_pclk("p6_pclk7", "per6clk", U8500_CLKRST6_BASE,
 				BIT(7), 0);
+	clk_register_clkdev(clk, "apb_pclk", "mtu1");
 
 	/* PRCC K-clocks
 	 *
diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig
index a098573..7fdcbd3 100644
--- a/drivers/clocksource/Kconfig
+++ b/drivers/clocksource/Kconfig
@@ -25,6 +25,21 @@
 config SUNXI_TIMER
 	bool
 
+config CLKSRC_NOMADIK_MTU
+	bool
+	depends on (ARCH_NOMADIK || ARCH_U8500)
+	select CLKSRC_MMIO
+	help
+	  Support for Multi Timer Unit. MTU provides access
+	  to multiple interrupt generating programmable
+	  32-bit free running decrementing counters.
+
+config CLKSRC_NOMADIK_MTU_SCHED_CLOCK
+	bool
+	depends on CLKSRC_NOMADIK_MTU
+	help
+	  Use the Multi Timer Unit as the sched_clock.
+
 config CLKSRC_DBX500_PRCMU
 	bool "Clocksource PRCMU Timer"
 	depends on UX500_SOC_DB8500
@@ -34,7 +49,7 @@
 
 config CLKSRC_DBX500_PRCMU_SCHED_CLOCK
 	bool "Clocksource PRCMU Timer sched_clock"
-	depends on (CLKSRC_DBX500_PRCMU && !NOMADIK_MTU_SCHED_CLOCK)
+	depends on (CLKSRC_DBX500_PRCMU && !CLKSRC_NOMADIK_MTU_SCHED_CLOCK)
 	default y
 	help
 	  Use the always on PRCMU Timer as sched_clock
diff --git a/drivers/clocksource/Makefile b/drivers/clocksource/Makefile
index 36f06de..f93453d 100644
--- a/drivers/clocksource/Makefile
+++ b/drivers/clocksource/Makefile
@@ -11,6 +11,7 @@
 obj-$(CONFIG_CLKSRC_MMIO)	+= mmio.o
 obj-$(CONFIG_DW_APB_TIMER)	+= dw_apb_timer.o
 obj-$(CONFIG_DW_APB_TIMER_OF)	+= dw_apb_timer_of.o
+obj-$(CONFIG_CLKSRC_NOMADIK_MTU)	+= nomadik-mtu.o
 obj-$(CONFIG_CLKSRC_DBX500_PRCMU)	+= clksrc-dbx500-prcmu.o
 obj-$(CONFIG_ARMADA_370_XP_TIMER)	+= time-armada-370-xp.o
 obj-$(CONFIG_ARCH_BCM2835)	+= bcm2835_timer.o
diff --git a/arch/arm/plat-nomadik/timer.c b/drivers/clocksource/nomadik-mtu.c
similarity index 92%
rename from arch/arm/plat-nomadik/timer.c
rename to drivers/clocksource/nomadik-mtu.c
index 9222e55..8914c3c 100644
--- a/arch/arm/plat-nomadik/timer.c
+++ b/drivers/clocksource/nomadik-mtu.c
@@ -1,6 +1,4 @@
 /*
- *  linux/arch/arm/plat-nomadik/timer.c
- *
  * Copyright (C) 2008 STMicroelectronics
  * Copyright (C) 2010 Alessandro Rubini
  * Copyright (C) 2010 Linus Walleij for ST-Ericsson
@@ -14,9 +12,11 @@
 #include <linux/irq.h>
 #include <linux/io.h>
 #include <linux/clockchips.h>
+#include <linux/clocksource.h>
 #include <linux/clk.h>
 #include <linux/jiffies.h>
 #include <linux/err.h>
+#include <linux/platform_data/clocksource-nomadik-mtu.h>
 #include <asm/mach/time.h>
 #include <asm/sched_clock.h>
 
@@ -174,12 +174,18 @@
 	       mtu_base + MTU_CR(0));
 }
 
-void __init nmdk_timer_init(void __iomem *base)
+void __init nmdk_timer_init(void __iomem *base, int irq)
 {
 	unsigned long rate;
-	struct clk *clk0;
+	struct clk *clk0, *pclk0;
 
 	mtu_base = base;
+
+	pclk0 = clk_get_sys("mtu0", "apb_pclk");
+	BUG_ON(IS_ERR(pclk0));
+	BUG_ON(clk_prepare(pclk0) < 0);
+	BUG_ON(clk_enable(pclk0) < 0);
+
 	clk0 = clk_get_sys("mtu0", NULL);
 	BUG_ON(IS_ERR(clk0));
 	BUG_ON(clk_prepare(clk0) < 0);
@@ -201,7 +207,8 @@
 		clk_prescale = MTU_CRn_PRESCALE_1;
 	}
 
-	nmdk_cycle = (rate + HZ/2) / HZ;
+	/* Cycles for periodic mode */
+	nmdk_cycle = DIV_ROUND_CLOSEST(rate, HZ);
 
 
 	/* Timer 0 is the free running clocksource */
@@ -217,7 +224,7 @@
 #endif
 
 	/* Timer 1 is used for events, register irq and clockevents */
-	setup_irq(IRQ_MTU0, &nmdk_timer_irq);
+	setup_irq(irq, &nmdk_timer_irq);
 	nmdk_clkevt.cpumask = cpumask_of(0);
 	clockevents_config_and_register(&nmdk_clkevt, rate, 2, 0xffffffffU);
 }
diff --git a/drivers/crypto/ux500/cryp/cryp_core.c b/drivers/crypto/ux500/cryp/cryp_core.c
index bc615cc..8bc5fef 100644
--- a/drivers/crypto/ux500/cryp/cryp_core.c
+++ b/drivers/crypto/ux500/cryp/cryp_core.c
@@ -23,6 +23,7 @@
 #include <linux/platform_device.h>
 #include <linux/regulator/consumer.h>
 #include <linux/semaphore.h>
+#include <linux/platform_data/dma-ste-dma40.h>
 
 #include <crypto/aes.h>
 #include <crypto/algapi.h>
@@ -30,8 +31,6 @@
 #include <crypto/des.h>
 #include <crypto/scatterwalk.h>
 
-#include <plat/ste_dma40.h>
-
 #include <linux/platform_data/crypto-ux500.h>
 #include <mach/hardware.h>
 
diff --git a/drivers/dma/ste_dma40.c b/drivers/dma/ste_dma40.c
index ae55091..23c5573 100644
--- a/drivers/dma/ste_dma40.c
+++ b/drivers/dma/ste_dma40.c
@@ -19,8 +19,7 @@
 #include <linux/err.h>
 #include <linux/amba/bus.h>
 #include <linux/regulator/consumer.h>
-
-#include <plat/ste_dma40.h>
+#include <linux/platform_data/dma-ste-dma40.h>
 
 #include "dmaengine.h"
 #include "ste_dma40_ll.h"
diff --git a/drivers/dma/ste_dma40_ll.c b/drivers/dma/ste_dma40_ll.c
index cad9e1d..851ad56 100644
--- a/drivers/dma/ste_dma40_ll.c
+++ b/drivers/dma/ste_dma40_ll.c
@@ -6,7 +6,7 @@
  */
 
 #include <linux/kernel.h>
-#include <plat/ste_dma40.h>
+#include <linux/platform_data/dma-ste-dma40.h>
 
 #include "ste_dma40_ll.h"
 
diff --git a/drivers/input/keyboard/Kconfig b/drivers/input/keyboard/Kconfig
index de08740..77629d3 100644
--- a/drivers/input/keyboard/Kconfig
+++ b/drivers/input/keyboard/Kconfig
@@ -409,7 +409,7 @@
 
 config KEYBOARD_NOMADIK
 	tristate "ST-Ericsson Nomadik SKE keyboard"
-	depends on PLAT_NOMADIK
+	depends on (ARCH_NOMADIK || ARCH_U8500)
 	select INPUT_MATRIXKMAP
 	help
 	  Say Y here if you want to use a keypad provided on the SKE controller
diff --git a/drivers/mfd/ab8500-core.c b/drivers/mfd/ab8500-core.c
index 127b00a..3e27c03 100644
--- a/drivers/mfd/ab8500-core.c
+++ b/drivers/mfd/ab8500-core.c
@@ -565,15 +565,10 @@
 	else
 		num_irqs = AB8500_NR_IRQS;
 
-	if (ab8500->irq_base) {
-		ab8500->domain = irq_domain_add_legacy(
-			NULL, num_irqs, ab8500->irq_base,
-			0, &ab8500_irq_ops, ab8500);
-	}
-	else {
-		ab8500->domain = irq_domain_add_linear(
-			np, num_irqs, &ab8500_irq_ops, ab8500);
-	}
+	/* If ->irq_base is zero this will give a linear mapping */
+	ab8500->domain = irq_domain_add_simple(NULL,
+			num_irqs, ab8500->irq_base,
+			&ab8500_irq_ops, ab8500);
 
 	if (!ab8500->domain) {
 		dev_err(ab8500->dev, "Failed to create irqdomain\n");
diff --git a/drivers/mfd/db8500-prcmu.c b/drivers/mfd/db8500-prcmu.c
index dc56915..2971056 100644
--- a/drivers/mfd/db8500-prcmu.c
+++ b/drivers/mfd/db8500-prcmu.c
@@ -2743,9 +2743,15 @@
 
 static int db8500_irq_init(struct device_node *np)
 {
-	db8500_irq_domain = irq_domain_add_legacy(
-		np, NUM_PRCMU_WAKEUPS, IRQ_PRCMU_BASE,
-		0, &db8500_irq_ops, NULL);
+	int irq_base = -1;
+
+	/* In the device tree case, just take some IRQs */
+	if (!np)
+		irq_base = IRQ_PRCMU_BASE;
+
+	db8500_irq_domain = irq_domain_add_simple(
+		np, NUM_PRCMU_WAKEUPS, irq_base,
+		&db8500_irq_ops, NULL);
 
 	if (!db8500_irq_domain) {
 		pr_err("Failed to create irqdomain\n");
diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index 531807d..dae191b 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -546,7 +546,7 @@
 
 config MTD_NAND_FSMC
 	tristate "Support for NAND on ST Micros FSMC"
-	depends on PLAT_SPEAR || PLAT_NOMADIK || MACH_U300
+	depends on PLAT_SPEAR || ARCH_NOMADIK || ARCH_U8500 || MACH_U300
 	help
 	  Enables support for NAND Flash chips on the ST Microelectronics
 	  Flexible Static Memory Controller (FSMC)
diff --git a/drivers/pinctrl/pinctrl-nomadik.c b/drivers/pinctrl/pinctrl-nomadik.c
index 8ef3e85..ef66f98 100644
--- a/drivers/pinctrl/pinctrl-nomadik.c
+++ b/drivers/pinctrl/pinctrl-nomadik.c
@@ -31,9 +31,8 @@
 /* Since we request GPIOs from ourself */
 #include <linux/pinctrl/consumer.h>
 #include <linux/platform_data/pinctrl-nomadik.h>
-
 #include <asm/mach/irq.h>
-
+#include <mach/irqs.h>
 #include "pinctrl-nomadik.h"
 
 /*
diff --git a/arch/arm/plat-nomadik/include/plat/mtu.h b/include/linux/platform_data/clocksource-nomadik-mtu.h
similarity index 71%
rename from arch/arm/plat-nomadik/include/plat/mtu.h
rename to include/linux/platform_data/clocksource-nomadik-mtu.h
index 582641f..8008897 100644
--- a/arch/arm/plat-nomadik/include/plat/mtu.h
+++ b/include/linux/platform_data/clocksource-nomadik-mtu.h
@@ -1,7 +1,7 @@
 #ifndef __PLAT_MTU_H
 #define __PLAT_MTU_H
 
-void nmdk_timer_init(void __iomem *base);
+void nmdk_timer_init(void __iomem *base, int irq);
 void nmdk_clkevt_reset(void);
 void nmdk_clksrc_reset(void);
 
diff --git a/include/linux/platform_data/crypto-ux500.h b/include/linux/platform_data/crypto-ux500.h
index 5b2d081..94df96d 100644
--- a/include/linux/platform_data/crypto-ux500.h
+++ b/include/linux/platform_data/crypto-ux500.h
@@ -7,7 +7,7 @@
 #ifndef _CRYPTO_UX500_H
 #define _CRYPTO_UX500_H
 #include <linux/dmaengine.h>
-#include <plat/ste_dma40.h>
+#include <linux/platform_data/dma-ste-dma40.h>
 
 struct hash_platform_data {
 	void *mem_to_engine;
diff --git a/arch/arm/plat-nomadik/include/plat/ste_dma40.h b/include/linux/platform_data/dma-ste-dma40.h
similarity index 100%
rename from arch/arm/plat-nomadik/include/plat/ste_dma40.h
rename to include/linux/platform_data/dma-ste-dma40.h
diff --git a/sound/soc/ux500/ux500_pcm.c b/sound/soc/ux500/ux500_pcm.c
index 1a04e24..b55b79f 100644
--- a/sound/soc/ux500/ux500_pcm.c
+++ b/sound/soc/ux500/ux500_pcm.c
@@ -18,8 +18,7 @@
 #include <linux/dma-mapping.h>
 #include <linux/dmaengine.h>
 #include <linux/slab.h>
-
-#include <plat/ste_dma40.h>
+#include <linux/platform_data/dma-ste-dma40.h>
 
 #include <sound/pcm.h>
 #include <sound/pcm_params.h>