Merge branch 'irqdomain/next' into gpio/next
diff --git a/Documentation/devicetree/bindings/gpio/sodaville.txt b/Documentation/devicetree/bindings/gpio/sodaville.txt
new file mode 100644
index 0000000..563eff22
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/sodaville.txt
@@ -0,0 +1,48 @@
+GPIO controller on CE4100 / Sodaville SoCs
+==========================================
+
+The bindings for CE4100's GPIO controller match the generic description
+which is covered by the gpio.txt file in this folder.
+
+The only additional property is the intel,muxctl property which holds the
+value which is written into the MUXCNTL register.
+
+There is no compatible property for now because the driver is probed via
+PCI id (vendor 0x8086 device 0x2e67).
+
+The interrupt specifier consists of two cells encoded as follows:
+ - <1st cell>: The interrupt-number that identifies the interrupt source.
+ - <2nd cell>: The level-sense information, encoded as follows:
+ 4 - active high level-sensitive
+ 8 - active low level-sensitive
+
+Example of the GPIO device and one user:
+
+ pcigpio: gpio@b,1 {
+ /* two cells for GPIO and interrupt */
+ #gpio-cells = <2>;
+ #interrupt-cells = <2>;
+ compatible = "pci8086,2e67.2",
+ "pci8086,2e67",
+ "pciclassff0000",
+ "pciclassff00";
+
+ reg = <0x15900 0x0 0x0 0x0 0x0>;
+ /* Interrupt line of the gpio device */
+ interrupts = <15 1>;
+ /* It is an interrupt and GPIO controller itself */
+ interrupt-controller;
+ gpio-controller;
+ intel,muxctl = <0>;
+ };
+
+ testuser@20 {
+ compatible = "example,testuser";
+ /* User the 11th GPIO line as an active high triggered
+ * level interrupt
+ */
+ interrupts = <11 8>;
+ interrupt-parent = <&pcigpio>;
+ /* Use this GPIO also with the gpio functions */
+ gpios = <&pcigpio 11 0>;
+ };
diff --git a/arch/arm/mach-omap1/gpio15xx.c b/arch/arm/mach-omap1/gpio15xx.c
index 399da4c..634903e 100644
--- a/arch/arm/mach-omap1/gpio15xx.c
+++ b/arch/arm/mach-omap1/gpio15xx.c
@@ -42,11 +42,12 @@
.irqstatus = OMAP_MPUIO_GPIO_INT,
.irqenable = OMAP_MPUIO_GPIO_MASKIT,
.irqenable_inv = true,
+ .irqctrl = OMAP_MPUIO_GPIO_INT_EDGE,
};
static struct __initdata omap_gpio_platform_data omap15xx_mpu_gpio_config = {
.virtual_irq_start = IH_MPUIO_BASE,
- .bank_type = METHOD_MPUIO,
+ .is_mpuio = true,
.bank_width = 16,
.bank_stride = 1,
.regs = &omap15xx_mpuio_regs,
@@ -83,11 +84,12 @@
.irqstatus = OMAP1510_GPIO_INT_STATUS,
.irqenable = OMAP1510_GPIO_INT_MASK,
.irqenable_inv = true,
+ .irqctrl = OMAP1510_GPIO_INT_CONTROL,
+ .pinctrl = OMAP1510_GPIO_PIN_CONTROL,
};
static struct __initdata omap_gpio_platform_data omap15xx_gpio_config = {
.virtual_irq_start = IH_GPIO_BASE,
- .bank_type = METHOD_GPIO_1510,
.bank_width = 16,
.regs = &omap15xx_gpio_regs,
};
@@ -115,7 +117,6 @@
platform_device_register(&omap15xx_mpu_gpio);
platform_device_register(&omap15xx_gpio);
- gpio_bank_count = 2;
return 0;
}
postcore_initcall(omap15xx_gpio_init);
diff --git a/arch/arm/mach-omap1/gpio16xx.c b/arch/arm/mach-omap1/gpio16xx.c
index 0f399bd..1c5f90e 100644
--- a/arch/arm/mach-omap1/gpio16xx.c
+++ b/arch/arm/mach-omap1/gpio16xx.c
@@ -24,6 +24,9 @@
#define OMAP1610_GPIO4_BASE 0xfffbbc00
#define OMAP1_MPUIO_VBASE OMAP1_MPUIO_BASE
+/* smart idle, enable wakeup */
+#define SYSCONFIG_WORD 0x14
+
/* mpu gpio */
static struct __initdata resource omap16xx_mpu_gpio_resources[] = {
{
@@ -45,11 +48,12 @@
.irqstatus = OMAP_MPUIO_GPIO_INT,
.irqenable = OMAP_MPUIO_GPIO_MASKIT,
.irqenable_inv = true,
+ .irqctrl = OMAP_MPUIO_GPIO_INT_EDGE,
};
static struct __initdata omap_gpio_platform_data omap16xx_mpu_gpio_config = {
.virtual_irq_start = IH_MPUIO_BASE,
- .bank_type = METHOD_MPUIO,
+ .is_mpuio = true,
.bank_width = 16,
.bank_stride = 1,
.regs = &omap16xx_mpuio_regs,
@@ -89,11 +93,13 @@
.irqenable = OMAP1610_GPIO_IRQENABLE1,
.set_irqenable = OMAP1610_GPIO_SET_IRQENABLE1,
.clr_irqenable = OMAP1610_GPIO_CLEAR_IRQENABLE1,
+ .wkup_en = OMAP1610_GPIO_WAKEUPENABLE,
+ .edgectrl1 = OMAP1610_GPIO_EDGE_CTRL1,
+ .edgectrl2 = OMAP1610_GPIO_EDGE_CTRL2,
};
static struct __initdata omap_gpio_platform_data omap16xx_gpio1_config = {
.virtual_irq_start = IH_GPIO_BASE,
- .bank_type = METHOD_GPIO_1610,
.bank_width = 16,
.regs = &omap16xx_gpio_regs,
};
@@ -123,7 +129,6 @@
static struct __initdata omap_gpio_platform_data omap16xx_gpio2_config = {
.virtual_irq_start = IH_GPIO_BASE + 16,
- .bank_type = METHOD_GPIO_1610,
.bank_width = 16,
.regs = &omap16xx_gpio_regs,
};
@@ -153,7 +158,6 @@
static struct __initdata omap_gpio_platform_data omap16xx_gpio3_config = {
.virtual_irq_start = IH_GPIO_BASE + 32,
- .bank_type = METHOD_GPIO_1610,
.bank_width = 16,
.regs = &omap16xx_gpio_regs,
};
@@ -183,7 +187,6 @@
static struct __initdata omap_gpio_platform_data omap16xx_gpio4_config = {
.virtual_irq_start = IH_GPIO_BASE + 48,
- .bank_type = METHOD_GPIO_1610,
.bank_width = 16,
.regs = &omap16xx_gpio_regs,
};
@@ -214,14 +217,42 @@
static int __init omap16xx_gpio_init(void)
{
int i;
+ void __iomem *base;
+ struct resource *res;
+ struct platform_device *pdev;
+ struct omap_gpio_platform_data *pdata;
if (!cpu_is_omap16xx())
return -EINVAL;
- for (i = 0; i < ARRAY_SIZE(omap16xx_gpio_dev); i++)
- platform_device_register(omap16xx_gpio_dev[i]);
+ for (i = 0; i < ARRAY_SIZE(omap16xx_gpio_dev); i++) {
+ pdev = omap16xx_gpio_dev[i];
+ pdata = pdev->dev.platform_data;
- gpio_bank_count = ARRAY_SIZE(omap16xx_gpio_dev);
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (unlikely(!res)) {
+ dev_err(&pdev->dev, "Invalid mem resource.\n");
+ return -ENODEV;
+ }
+
+ base = ioremap(res->start, resource_size(res));
+ if (unlikely(!base)) {
+ dev_err(&pdev->dev, "ioremap failed.\n");
+ return -ENOMEM;
+ }
+
+ __raw_writel(SYSCONFIG_WORD, base + OMAP1610_GPIO_SYSCONFIG);
+ iounmap(base);
+
+ /*
+ * Enable system clock for GPIO module.
+ * The CAM_CLK_CTRL *is* really the right place.
+ */
+ omap_writel(omap_readl(ULPD_CAM_CLK_CTRL) | 0x04,
+ ULPD_CAM_CLK_CTRL);
+
+ platform_device_register(omap16xx_gpio_dev[i]);
+ }
return 0;
}
diff --git a/arch/arm/mach-omap1/gpio7xx.c b/arch/arm/mach-omap1/gpio7xx.c
index 5ab63ea..4771d6b 100644
--- a/arch/arm/mach-omap1/gpio7xx.c
+++ b/arch/arm/mach-omap1/gpio7xx.c
@@ -47,12 +47,13 @@
.irqstatus = OMAP_MPUIO_GPIO_INT / 2,
.irqenable = OMAP_MPUIO_GPIO_MASKIT / 2,
.irqenable_inv = true,
+ .irqctrl = OMAP_MPUIO_GPIO_INT_EDGE >> 1,
};
static struct __initdata omap_gpio_platform_data omap7xx_mpu_gpio_config = {
.virtual_irq_start = IH_MPUIO_BASE,
- .bank_type = METHOD_MPUIO,
- .bank_width = 32,
+ .is_mpuio = true,
+ .bank_width = 16,
.bank_stride = 2,
.regs = &omap7xx_mpuio_regs,
};
@@ -88,11 +89,11 @@
.irqstatus = OMAP7XX_GPIO_INT_STATUS,
.irqenable = OMAP7XX_GPIO_INT_MASK,
.irqenable_inv = true,
+ .irqctrl = OMAP7XX_GPIO_INT_CONTROL,
};
static struct __initdata omap_gpio_platform_data omap7xx_gpio1_config = {
.virtual_irq_start = IH_GPIO_BASE,
- .bank_type = METHOD_GPIO_7XX,
.bank_width = 32,
.regs = &omap7xx_gpio_regs,
};
@@ -122,7 +123,6 @@
static struct __initdata omap_gpio_platform_data omap7xx_gpio2_config = {
.virtual_irq_start = IH_GPIO_BASE + 32,
- .bank_type = METHOD_GPIO_7XX,
.bank_width = 32,
.regs = &omap7xx_gpio_regs,
};
@@ -152,7 +152,6 @@
static struct __initdata omap_gpio_platform_data omap7xx_gpio3_config = {
.virtual_irq_start = IH_GPIO_BASE + 64,
- .bank_type = METHOD_GPIO_7XX,
.bank_width = 32,
.regs = &omap7xx_gpio_regs,
};
@@ -182,7 +181,6 @@
static struct __initdata omap_gpio_platform_data omap7xx_gpio4_config = {
.virtual_irq_start = IH_GPIO_BASE + 96,
- .bank_type = METHOD_GPIO_7XX,
.bank_width = 32,
.regs = &omap7xx_gpio_regs,
};
@@ -212,7 +210,6 @@
static struct __initdata omap_gpio_platform_data omap7xx_gpio5_config = {
.virtual_irq_start = IH_GPIO_BASE + 128,
- .bank_type = METHOD_GPIO_7XX,
.bank_width = 32,
.regs = &omap7xx_gpio_regs,
};
@@ -242,7 +239,6 @@
static struct __initdata omap_gpio_platform_data omap7xx_gpio6_config = {
.virtual_irq_start = IH_GPIO_BASE + 160,
- .bank_type = METHOD_GPIO_7XX,
.bank_width = 32,
.regs = &omap7xx_gpio_regs,
};
@@ -282,8 +278,6 @@
for (i = 0; i < ARRAY_SIZE(omap7xx_gpio_dev); i++)
platform_device_register(omap7xx_gpio_dev[i]);
- gpio_bank_count = ARRAY_SIZE(omap7xx_gpio_dev);
-
return 0;
}
postcore_initcall(omap7xx_gpio_init);
diff --git a/arch/arm/mach-omap2/gpio.c b/arch/arm/mach-omap2/gpio.c
index 8cbfbc2..1e0b750 100644
--- a/arch/arm/mach-omap2/gpio.c
+++ b/arch/arm/mach-omap2/gpio.c
@@ -23,6 +23,9 @@
#include <plat/omap_hwmod.h>
#include <plat/omap_device.h>
+#include <plat/omap-pm.h>
+
+#include "powerdomain.h"
static int omap2_gpio_dev_init(struct omap_hwmod *oh, void *unused)
{
@@ -31,6 +34,7 @@
struct omap_gpio_dev_attr *dev_attr;
char *name = "omap_gpio";
int id;
+ struct powerdomain *pwrdm;
/*
* extract the device id from name field available in the
@@ -52,7 +56,7 @@
pdata->bank_width = dev_attr->bank_width;
pdata->dbck_flag = dev_attr->dbck_flag;
pdata->virtual_irq_start = IH_GPIO_BASE + 32 * (id - 1);
-
+ pdata->get_context_loss_count = omap_pm_get_dev_context_loss_count;
pdata->regs = kzalloc(sizeof(struct omap_gpio_reg_offs), GFP_KERNEL);
if (!pdata) {
pr_err("gpio%d: Memory allocation failed\n", id);
@@ -61,8 +65,15 @@
switch (oh->class->rev) {
case 0:
+ if (id == 1)
+ /* non-wakeup GPIO pins for OMAP2 Bank1 */
+ pdata->non_wakeup_gpios = 0xe203ffc0;
+ else if (id == 2)
+ /* non-wakeup GPIO pins for OMAP2 Bank2 */
+ pdata->non_wakeup_gpios = 0x08700040;
+ /* fall through */
+
case 1:
- pdata->bank_type = METHOD_GPIO_24XX;
pdata->regs->revision = OMAP24XX_GPIO_REVISION;
pdata->regs->direction = OMAP24XX_GPIO_OE;
pdata->regs->datain = OMAP24XX_GPIO_DATAIN;
@@ -72,13 +83,19 @@
pdata->regs->irqstatus = OMAP24XX_GPIO_IRQSTATUS1;
pdata->regs->irqstatus2 = OMAP24XX_GPIO_IRQSTATUS2;
pdata->regs->irqenable = OMAP24XX_GPIO_IRQENABLE1;
+ pdata->regs->irqenable2 = OMAP24XX_GPIO_IRQENABLE2;
pdata->regs->set_irqenable = OMAP24XX_GPIO_SETIRQENABLE1;
pdata->regs->clr_irqenable = OMAP24XX_GPIO_CLEARIRQENABLE1;
pdata->regs->debounce = OMAP24XX_GPIO_DEBOUNCE_VAL;
pdata->regs->debounce_en = OMAP24XX_GPIO_DEBOUNCE_EN;
+ pdata->regs->ctrl = OMAP24XX_GPIO_CTRL;
+ pdata->regs->wkup_en = OMAP24XX_GPIO_WAKE_EN;
+ pdata->regs->leveldetect0 = OMAP24XX_GPIO_LEVELDETECT0;
+ pdata->regs->leveldetect1 = OMAP24XX_GPIO_LEVELDETECT1;
+ pdata->regs->risingdetect = OMAP24XX_GPIO_RISINGDETECT;
+ pdata->regs->fallingdetect = OMAP24XX_GPIO_FALLINGDETECT;
break;
case 2:
- pdata->bank_type = METHOD_GPIO_44XX;
pdata->regs->revision = OMAP4_GPIO_REVISION;
pdata->regs->direction = OMAP4_GPIO_OE;
pdata->regs->datain = OMAP4_GPIO_DATAIN;
@@ -88,10 +105,17 @@
pdata->regs->irqstatus = OMAP4_GPIO_IRQSTATUS0;
pdata->regs->irqstatus2 = OMAP4_GPIO_IRQSTATUS1;
pdata->regs->irqenable = OMAP4_GPIO_IRQSTATUSSET0;
+ pdata->regs->irqenable2 = OMAP4_GPIO_IRQSTATUSSET1;
pdata->regs->set_irqenable = OMAP4_GPIO_IRQSTATUSSET0;
pdata->regs->clr_irqenable = OMAP4_GPIO_IRQSTATUSCLR0;
pdata->regs->debounce = OMAP4_GPIO_DEBOUNCINGTIME;
pdata->regs->debounce_en = OMAP4_GPIO_DEBOUNCENABLE;
+ pdata->regs->ctrl = OMAP4_GPIO_CTRL;
+ pdata->regs->wkup_en = OMAP4_GPIO_IRQWAKEN0;
+ pdata->regs->leveldetect0 = OMAP4_GPIO_LEVELDETECT0;
+ pdata->regs->leveldetect1 = OMAP4_GPIO_LEVELDETECT1;
+ pdata->regs->risingdetect = OMAP4_GPIO_RISINGDETECT;
+ pdata->regs->fallingdetect = OMAP4_GPIO_FALLINGDETECT;
break;
default:
WARN(1, "Invalid gpio bank_type\n");
@@ -99,6 +123,9 @@
return -EINVAL;
}
+ pwrdm = omap_hwmod_get_pwrdm(oh);
+ pdata->loses_context = pwrdm_can_ever_lose_context(pwrdm);
+
pdev = omap_device_build(name, id - 1, oh, pdata,
sizeof(*pdata), NULL, 0, false);
kfree(pdata);
@@ -109,9 +136,6 @@
return PTR_ERR(pdev);
}
- omap_device_disable_idle_on_suspend(pdev);
-
- gpio_bank_count++;
return 0;
}
diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c
index fc69875..59c6dc1 100644
--- a/arch/arm/mach-omap2/pm34xx.c
+++ b/arch/arm/mach-omap2/pm34xx.c
@@ -75,16 +75,6 @@
static struct powerdomain *core_pwrdm, *per_pwrdm;
static struct powerdomain *cam_pwrdm;
-static inline void omap3_per_save_context(void)
-{
- omap_gpio_save_context();
-}
-
-static inline void omap3_per_restore_context(void)
-{
- omap_gpio_restore_context();
-}
-
static void omap3_enable_io_chain(void)
{
int timeout = 0;
@@ -332,8 +322,6 @@
if (per_next_state < PWRDM_POWER_ON) {
per_going_off = (per_next_state == PWRDM_POWER_OFF) ? 1 : 0;
omap2_gpio_prepare_for_idle(per_going_off);
- if (per_next_state == PWRDM_POWER_OFF)
- omap3_per_save_context();
}
/* CORE */
@@ -399,8 +387,6 @@
if (per_next_state < PWRDM_POWER_ON) {
per_prev_state = pwrdm_read_prev_pwrst(per_pwrdm);
omap2_gpio_resume_after_idle();
- if (per_prev_state == PWRDM_POWER_OFF)
- omap3_per_restore_context();
}
/* Disable IO-PAD and IO-CHAIN wakeup */
diff --git a/arch/arm/plat-omap/include/plat/gpio.h b/arch/arm/plat-omap/include/plat/gpio.h
index 9e86ee0..cb75b65 100644
--- a/arch/arm/plat-omap/include/plat/gpio.h
+++ b/arch/arm/plat-omap/include/plat/gpio.h
@@ -162,13 +162,6 @@
IH_MPUIO_BASE + ((nr) & 0x0f) : \
IH_GPIO_BASE + (nr))
-#define METHOD_MPUIO 0
-#define METHOD_GPIO_1510 1
-#define METHOD_GPIO_1610 2
-#define METHOD_GPIO_7XX 3
-#define METHOD_GPIO_24XX 5
-#define METHOD_GPIO_44XX 6
-
struct omap_gpio_dev_attr {
int bank_width; /* GPIO bank width */
bool dbck_flag; /* dbck required or not - True for OMAP3&4 */
@@ -184,10 +177,21 @@
u16 irqstatus;
u16 irqstatus2;
u16 irqenable;
+ u16 irqenable2;
u16 set_irqenable;
u16 clr_irqenable;
u16 debounce;
u16 debounce_en;
+ u16 ctrl;
+ u16 wkup_en;
+ u16 leveldetect0;
+ u16 leveldetect1;
+ u16 risingdetect;
+ u16 fallingdetect;
+ u16 irqctrl;
+ u16 edgectrl1;
+ u16 edgectrl2;
+ u16 pinctrl;
bool irqenable_inv;
};
@@ -198,19 +202,20 @@
int bank_width; /* GPIO bank width */
int bank_stride; /* Only needed for omap1 MPUIO */
bool dbck_flag; /* dbck required or not - True for OMAP3&4 */
+ bool loses_context; /* whether the bank would ever lose context */
+ bool is_mpuio; /* whether the bank is of type MPUIO */
+ u32 non_wakeup_gpios;
struct omap_gpio_reg_offs *regs;
-};
-/* TODO: Analyze removing gpio_bank_count usage from driver code */
-extern int gpio_bank_count;
+ /* Return context loss count due to PM states changing */
+ int (*get_context_loss_count)(struct device *dev);
+};
extern void omap2_gpio_prepare_for_idle(int off_mode);
extern void omap2_gpio_resume_after_idle(void);
extern void omap_set_gpio_debounce(int gpio, int enable);
extern void omap_set_gpio_debounce_time(int gpio, int enable);
-extern void omap_gpio_save_context(void);
-extern void omap_gpio_restore_context(void);
/*-------------------------------------------------------------------------*/
/* Wrappers for "new style" GPIO calls, using the new infrastructure
diff --git a/arch/x86/platform/ce4100/falconfalls.dts b/arch/x86/platform/ce4100/falconfalls.dts
index e70be38..ce874f8 100644
--- a/arch/x86/platform/ce4100/falconfalls.dts
+++ b/arch/x86/platform/ce4100/falconfalls.dts
@@ -208,16 +208,19 @@
interrupts = <14 1>;
};
- gpio@b,1 {
+ pcigpio: gpio@b,1 {
+ #gpio-cells = <2>;
+ #interrupt-cells = <2>;
compatible = "pci8086,2e67.2",
"pci8086,2e67",
"pciclassff0000",
"pciclassff00";
- #gpio-cells = <2>;
reg = <0x15900 0x0 0x0 0x0 0x0>;
interrupts = <15 1>;
+ interrupt-controller;
gpio-controller;
+ intel,muxctl = <0>;
};
i2c-controller@b,2 {
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index d0c4118..dbb1909 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -225,6 +225,12 @@
Say yes here to enable the max732x to be used as an interrupt
controller. It requires the driver to be built in the kernel.
+config GPIO_MC9S08DZ60
+ bool "MX35 3DS BOARD MC9S08DZ60 GPIO functions"
+ depends on I2C && MACH_MX35_3DS
+ help
+ Select this to enable the MC9S08DZ60 GPIO driver
+
config GPIO_PCA953X
tristate "PCA953x, PCA955x, TCA64xx, and MAX7310 I/O ports"
depends on I2C
@@ -411,6 +417,14 @@
Hub) which is for IVI(In-Vehicle Infotainment) use.
This driver can access the IOH's GPIO device.
+config GPIO_SODAVILLE
+ bool "Intel Sodaville GPIO support"
+ depends on X86 && PCI && OF
+ select GPIO_GENERIC
+ select GENERIC_IRQ_CHIP
+ help
+ Say Y here to support Intel Sodaville GPIO.
+
config GPIO_TIMBERDALE
bool "Support for timberdale GPIO IP"
depends on MFD_TIMBERDALE && HAS_IOMEM
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index fa10df6..593bdcd 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -26,6 +26,7 @@
obj-$(CONFIG_GPIO_MAX7301) += gpio-max7301.o
obj-$(CONFIG_GPIO_MAX732X) += gpio-max732x.o
obj-$(CONFIG_GPIO_MC33880) += gpio-mc33880.o
+obj-$(CONFIG_GPIO_MC9S08DZ60) += gpio-mc9s08dz60.o
obj-$(CONFIG_GPIO_MCP23S08) += gpio-mcp23s08.o
obj-$(CONFIG_GPIO_ML_IOH) += gpio-ml-ioh.o
obj-$(CONFIG_GPIO_MPC5200) += gpio-mpc5200.o
@@ -45,6 +46,7 @@
obj-$(CONFIG_PLAT_SAMSUNG) += gpio-samsung.o
obj-$(CONFIG_ARCH_SA1100) += gpio-sa1100.o
obj-$(CONFIG_GPIO_SCH) += gpio-sch.o
+obj-$(CONFIG_GPIO_SODAVILLE) += gpio-sodaville.o
obj-$(CONFIG_GPIO_STMPE) += gpio-stmpe.o
obj-$(CONFIG_GPIO_SX150X) += gpio-sx150x.o
obj-$(CONFIG_GPIO_TC3589X) += gpio-tc3589x.o
diff --git a/drivers/gpio/gpio-mc9s08dz60.c b/drivers/gpio/gpio-mc9s08dz60.c
new file mode 100644
index 0000000..2738cc4
--- /dev/null
+++ b/drivers/gpio/gpio-mc9s08dz60.c
@@ -0,0 +1,161 @@
+/*
+ * Copyright 2009-2012 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * Author: Wu Guoxing <b39297@freescale.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/i2c.h>
+#include <linux/gpio.h>
+
+#define GPIO_GROUP_NUM 2
+#define GPIO_NUM_PER_GROUP 8
+#define GPIO_NUM (GPIO_GROUP_NUM*GPIO_NUM_PER_GROUP)
+
+struct mc9s08dz60 {
+ struct i2c_client *client;
+ struct gpio_chip chip;
+};
+
+static inline struct mc9s08dz60 *to_mc9s08dz60(struct gpio_chip *gc)
+{
+ return container_of(gc, struct mc9s08dz60, chip);
+}
+
+
+static void mc9s_gpio_to_reg_and_bit(int offset, u8 *reg, u8 *bit)
+{
+ *reg = 0x20 + offset / GPIO_NUM_PER_GROUP;
+ *bit = offset % GPIO_NUM_PER_GROUP;
+}
+
+static int mc9s08dz60_get_value(struct gpio_chip *gc, unsigned offset)
+{
+ u8 reg, bit;
+ s32 value;
+ struct mc9s08dz60 *mc9s = to_mc9s08dz60(gc);
+
+ mc9s_gpio_to_reg_and_bit(offset, ®, &bit);
+ value = i2c_smbus_read_byte_data(mc9s->client, reg);
+
+ return (value >= 0) ? (value >> bit) & 0x1 : 0;
+}
+
+static int mc9s08dz60_set(struct mc9s08dz60 *mc9s, unsigned offset, int val)
+{
+ u8 reg, bit;
+ s32 value;
+
+ mc9s_gpio_to_reg_and_bit(offset, ®, &bit);
+ value = i2c_smbus_read_byte_data(mc9s->client, reg);
+ if (value >= 0) {
+ if (val)
+ value |= 1 << bit;
+ else
+ value &= ~(1 << bit);
+
+ return i2c_smbus_write_byte_data(mc9s->client, reg, value);
+ } else
+ return value;
+
+}
+
+
+static void mc9s08dz60_set_value(struct gpio_chip *gc, unsigned offset, int val)
+{
+ struct mc9s08dz60 *mc9s = to_mc9s08dz60(gc);
+
+ mc9s08dz60_set(mc9s, offset, val);
+}
+
+static int mc9s08dz60_direction_output(struct gpio_chip *gc,
+ unsigned offset, int val)
+{
+ struct mc9s08dz60 *mc9s = to_mc9s08dz60(gc);
+
+ return mc9s08dz60_set(mc9s, offset, val);
+}
+
+static int mc9s08dz60_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ int ret = 0;
+ struct mc9s08dz60 *mc9s;
+
+ mc9s = kzalloc(sizeof(*mc9s), GFP_KERNEL);
+ if (!mc9s)
+ return -ENOMEM;
+
+ mc9s->chip.label = client->name;
+ mc9s->chip.base = -1;
+ mc9s->chip.dev = &client->dev;
+ mc9s->chip.owner = THIS_MODULE;
+ mc9s->chip.ngpio = GPIO_NUM;
+ mc9s->chip.can_sleep = 1;
+ mc9s->chip.get = mc9s08dz60_get_value;
+ mc9s->chip.set = mc9s08dz60_set_value;
+ mc9s->chip.direction_output = mc9s08dz60_direction_output;
+ mc9s->client = client;
+ i2c_set_clientdata(client, mc9s);
+
+ ret = gpiochip_add(&mc9s->chip);
+ if (ret)
+ goto error;
+
+ return 0;
+
+ error:
+ kfree(mc9s);
+ return ret;
+}
+
+static int mc9s08dz60_remove(struct i2c_client *client)
+{
+ struct mc9s08dz60 *mc9s;
+ int ret;
+
+ mc9s = i2c_get_clientdata(client);
+
+ ret = gpiochip_remove(&mc9s->chip);
+ if (!ret)
+ kfree(mc9s);
+
+ return ret;
+
+}
+
+static const struct i2c_device_id mc9s08dz60_id[] = {
+ {"mc9s08dz60", 0},
+ {},
+};
+
+MODULE_DEVICE_TABLE(i2c, mc9s08dz60_id);
+
+static struct i2c_driver mc9s08dz60_i2c_driver = {
+ .driver = {
+ .owner = THIS_MODULE,
+ .name = "mc9s08dz60",
+ },
+ .probe = mc9s08dz60_probe,
+ .remove = mc9s08dz60_remove,
+ .id_table = mc9s08dz60_id,
+};
+
+module_i2c_driver(mc9s08dz60_i2c_driver);
+
+MODULE_AUTHOR("Freescale Semiconductor, Inc. "
+ "Wu Guoxing <b39297@freescale.com>");
+MODULE_DESCRIPTION("mc9s08dz60 gpio function on mx35 3ds board");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/gpio/gpio-omap.c b/drivers/gpio/gpio-omap.c
index 0b05629..f49bd6f 100644
--- a/drivers/gpio/gpio-omap.c
+++ b/drivers/gpio/gpio-omap.c
@@ -21,6 +21,7 @@
#include <linux/io.h>
#include <linux/slab.h>
#include <linux/pm_runtime.h>
+#include <linux/pm.h>
#include <mach/hardware.h>
#include <asm/irq.h>
@@ -28,41 +29,11 @@
#include <asm/gpio.h>
#include <asm/mach/irq.h>
-struct gpio_bank {
- unsigned long pbase;
- void __iomem *base;
- u16 irq;
- u16 virtual_irq_start;
- int method;
- u32 suspend_wakeup;
-#if defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP2PLUS)
- u32 saved_wakeup;
-#endif
- u32 non_wakeup_gpios;
- u32 enabled_non_wakeup_gpios;
+#define OFF_MODE 1
- u32 saved_datain;
- u32 saved_fallingdetect;
- u32 saved_risingdetect;
- u32 level_mask;
- u32 toggle_mask;
- spinlock_t lock;
- struct gpio_chip chip;
- struct clk *dbck;
- u32 mod_usage;
- u32 dbck_enable_mask;
- struct device *dev;
- bool dbck_flag;
- int stride;
- u32 width;
+static LIST_HEAD(omap_gpio_list);
- void (*set_dataout)(struct gpio_bank *bank, int gpio, int enable);
-
- struct omap_gpio_reg_offs *regs;
-};
-
-#ifdef CONFIG_ARCH_OMAP3
-struct omap3_gpio_regs {
+struct gpio_regs {
u32 irqenable1;
u32 irqenable2;
u32 wake_en;
@@ -73,22 +44,52 @@
u32 risingdetect;
u32 fallingdetect;
u32 dataout;
+ u32 debounce;
+ u32 debounce_en;
};
-static struct omap3_gpio_regs gpio_context[OMAP34XX_NR_GPIOS];
-#endif
+struct gpio_bank {
+ struct list_head node;
+ unsigned long pbase;
+ void __iomem *base;
+ u16 irq;
+ u16 virtual_irq_start;
+ u32 suspend_wakeup;
+ u32 saved_wakeup;
+ u32 non_wakeup_gpios;
+ u32 enabled_non_wakeup_gpios;
+ struct gpio_regs context;
+ u32 saved_datain;
+ u32 saved_fallingdetect;
+ u32 saved_risingdetect;
+ u32 level_mask;
+ u32 toggle_mask;
+ spinlock_t lock;
+ struct gpio_chip chip;
+ struct clk *dbck;
+ u32 mod_usage;
+ u32 dbck_enable_mask;
+ bool dbck_enabled;
+ struct device *dev;
+ bool is_mpuio;
+ bool dbck_flag;
+ bool loses_context;
+ int stride;
+ u32 width;
+ int context_loss_count;
+ u16 id;
+ int power_mode;
+ bool workaround_enabled;
-/*
- * TODO: Cleanup gpio_bank usage as it is having information
- * related to all instances of the device
- */
-static struct gpio_bank *gpio_bank;
+ void (*set_dataout)(struct gpio_bank *bank, int gpio, int enable);
+ int (*get_context_loss_count)(struct device *dev);
-/* TODO: Analyze removing gpio_bank_count usage from driver code */
-int gpio_bank_count;
+ struct omap_gpio_reg_offs *regs;
+};
#define GPIO_INDEX(bank, gpio) (gpio % bank->width)
#define GPIO_BIT(bank, gpio) (1 << GPIO_INDEX(bank, gpio))
+#define GPIO_MOD_CTRL_BIT BIT(0)
static void _set_gpio_direction(struct gpio_bank *bank, int gpio, int is_input)
{
@@ -102,6 +103,7 @@
else
l &= ~(1 << gpio);
__raw_writel(l, reg);
+ bank->context.oe = l;
}
@@ -132,6 +134,7 @@
else
l &= ~gpio_bit;
__raw_writel(l, reg);
+ bank->context.dataout = l;
}
static int _get_gpio_datain(struct gpio_bank *bank, int gpio)
@@ -160,6 +163,22 @@
__raw_writel(l, base + reg);
}
+static inline void _gpio_dbck_enable(struct gpio_bank *bank)
+{
+ if (bank->dbck_enable_mask && !bank->dbck_enabled) {
+ clk_enable(bank->dbck);
+ bank->dbck_enabled = true;
+ }
+}
+
+static inline void _gpio_dbck_disable(struct gpio_bank *bank)
+{
+ if (bank->dbck_enable_mask && bank->dbck_enabled) {
+ clk_disable(bank->dbck);
+ bank->dbck_enabled = false;
+ }
+}
+
/**
* _set_gpio_debounce - low level gpio debounce time
* @bank: the gpio bank we're acting upon
@@ -188,70 +207,74 @@
l = GPIO_BIT(bank, gpio);
+ clk_enable(bank->dbck);
reg = bank->base + bank->regs->debounce;
__raw_writel(debounce, reg);
reg = bank->base + bank->regs->debounce_en;
val = __raw_readl(reg);
- if (debounce) {
+ if (debounce)
val |= l;
- clk_enable(bank->dbck);
- } else {
+ else
val &= ~l;
- clk_disable(bank->dbck);
- }
bank->dbck_enable_mask = val;
__raw_writel(val, reg);
+ clk_disable(bank->dbck);
+ /*
+ * Enable debounce clock per module.
+ * This call is mandatory because in omap_gpio_request() when
+ * *_runtime_get_sync() is called, _gpio_dbck_enable() within
+ * runtime callbck fails to turn on dbck because dbck_enable_mask
+ * used within _gpio_dbck_enable() is still not initialized at
+ * that point. Therefore we have to enable dbck here.
+ */
+ _gpio_dbck_enable(bank);
+ if (bank->dbck_enable_mask) {
+ bank->context.debounce = debounce;
+ bank->context.debounce_en = val;
+ }
}
-#ifdef CONFIG_ARCH_OMAP2PLUS
-static inline void set_24xx_gpio_triggering(struct gpio_bank *bank, int gpio,
+static inline void set_gpio_trigger(struct gpio_bank *bank, int gpio,
int trigger)
{
void __iomem *base = bank->base;
u32 gpio_bit = 1 << gpio;
- if (cpu_is_omap44xx()) {
- _gpio_rmw(base, OMAP4_GPIO_LEVELDETECT0, gpio_bit,
- trigger & IRQ_TYPE_LEVEL_LOW);
- _gpio_rmw(base, OMAP4_GPIO_LEVELDETECT1, gpio_bit,
- trigger & IRQ_TYPE_LEVEL_HIGH);
- _gpio_rmw(base, OMAP4_GPIO_RISINGDETECT, gpio_bit,
- trigger & IRQ_TYPE_EDGE_RISING);
- _gpio_rmw(base, OMAP4_GPIO_FALLINGDETECT, gpio_bit,
- trigger & IRQ_TYPE_EDGE_FALLING);
- } else {
- _gpio_rmw(base, OMAP24XX_GPIO_LEVELDETECT0, gpio_bit,
- trigger & IRQ_TYPE_LEVEL_LOW);
- _gpio_rmw(base, OMAP24XX_GPIO_LEVELDETECT1, gpio_bit,
- trigger & IRQ_TYPE_LEVEL_HIGH);
- _gpio_rmw(base, OMAP24XX_GPIO_RISINGDETECT, gpio_bit,
- trigger & IRQ_TYPE_EDGE_RISING);
- _gpio_rmw(base, OMAP24XX_GPIO_FALLINGDETECT, gpio_bit,
- trigger & IRQ_TYPE_EDGE_FALLING);
- }
+ _gpio_rmw(base, bank->regs->leveldetect0, gpio_bit,
+ trigger & IRQ_TYPE_LEVEL_LOW);
+ _gpio_rmw(base, bank->regs->leveldetect1, gpio_bit,
+ trigger & IRQ_TYPE_LEVEL_HIGH);
+ _gpio_rmw(base, bank->regs->risingdetect, gpio_bit,
+ trigger & IRQ_TYPE_EDGE_RISING);
+ _gpio_rmw(base, bank->regs->fallingdetect, gpio_bit,
+ trigger & IRQ_TYPE_EDGE_FALLING);
+
+ bank->context.leveldetect0 =
+ __raw_readl(bank->base + bank->regs->leveldetect0);
+ bank->context.leveldetect1 =
+ __raw_readl(bank->base + bank->regs->leveldetect1);
+ bank->context.risingdetect =
+ __raw_readl(bank->base + bank->regs->risingdetect);
+ bank->context.fallingdetect =
+ __raw_readl(bank->base + bank->regs->fallingdetect);
+
if (likely(!(bank->non_wakeup_gpios & gpio_bit))) {
- if (cpu_is_omap44xx()) {
- _gpio_rmw(base, OMAP4_GPIO_IRQWAKEN0, gpio_bit,
- trigger != 0);
- } else {
- /*
- * GPIO wakeup request can only be generated on edge
- * transitions
- */
- if (trigger & IRQ_TYPE_EDGE_BOTH)
- __raw_writel(1 << gpio, bank->base
- + OMAP24XX_GPIO_SETWKUENA);
- else
- __raw_writel(1 << gpio, bank->base
- + OMAP24XX_GPIO_CLEARWKUENA);
- }
+ _gpio_rmw(base, bank->regs->wkup_en, gpio_bit, trigger != 0);
+ bank->context.wake_en =
+ __raw_readl(bank->base + bank->regs->wkup_en);
}
+
/* This part needs to be executed always for OMAP{34xx, 44xx} */
- if (cpu_is_omap34xx() || cpu_is_omap44xx() ||
- (bank->non_wakeup_gpios & gpio_bit)) {
+ if (!bank->regs->irqctrl) {
+ /* On omap24xx proceed only when valid GPIO bit is set */
+ if (bank->non_wakeup_gpios) {
+ if (!(bank->non_wakeup_gpios & gpio_bit))
+ goto exit;
+ }
+
/*
* Log the edge gpio and manually trigger the IRQ
* after resume if the input level changes
@@ -264,17 +287,11 @@
bank->enabled_non_wakeup_gpios &= ~gpio_bit;
}
- if (cpu_is_omap44xx()) {
- bank->level_mask =
- __raw_readl(bank->base + OMAP4_GPIO_LEVELDETECT0) |
- __raw_readl(bank->base + OMAP4_GPIO_LEVELDETECT1);
- } else {
- bank->level_mask =
- __raw_readl(bank->base + OMAP24XX_GPIO_LEVELDETECT0) |
- __raw_readl(bank->base + OMAP24XX_GPIO_LEVELDETECT1);
- }
+exit:
+ bank->level_mask =
+ __raw_readl(bank->base + bank->regs->leveldetect0) |
+ __raw_readl(bank->base + bank->regs->leveldetect1);
}
-#endif
#ifdef CONFIG_ARCH_OMAP1
/*
@@ -286,23 +303,10 @@
void __iomem *reg = bank->base;
u32 l = 0;
- switch (bank->method) {
- case METHOD_MPUIO:
- reg += OMAP_MPUIO_GPIO_INT_EDGE / bank->stride;
- break;
-#ifdef CONFIG_ARCH_OMAP15XX
- case METHOD_GPIO_1510:
- reg += OMAP1510_GPIO_INT_CONTROL;
- break;
-#endif
-#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
- case METHOD_GPIO_7XX:
- reg += OMAP7XX_GPIO_INT_CONTROL;
- break;
-#endif
- default:
+ if (!bank->regs->irqctrl)
return;
- }
+
+ reg += bank->regs->irqctrl;
l = __raw_readl(reg);
if ((l >> gpio) & 1)
@@ -312,17 +316,21 @@
__raw_writel(l, reg);
}
+#else
+static void _toggle_gpio_edge_triggering(struct gpio_bank *bank, int gpio) {}
#endif
static int _set_gpio_triggering(struct gpio_bank *bank, int gpio, int trigger)
{
void __iomem *reg = bank->base;
+ void __iomem *base = bank->base;
u32 l = 0;
- switch (bank->method) {
-#ifdef CONFIG_ARCH_OMAP1
- case METHOD_MPUIO:
- reg += OMAP_MPUIO_GPIO_INT_EDGE / bank->stride;
+ if (bank->regs->leveldetect0 && bank->regs->wkup_en) {
+ set_gpio_trigger(bank, gpio, trigger);
+ } else if (bank->regs->irqctrl) {
+ reg += bank->regs->irqctrl;
+
l = __raw_readl(reg);
if ((trigger & IRQ_TYPE_SENSE_MASK) == IRQ_TYPE_EDGE_BOTH)
bank->toggle_mask |= 1 << gpio;
@@ -331,29 +339,15 @@
else if (trigger & IRQ_TYPE_EDGE_FALLING)
l &= ~(1 << gpio);
else
- goto bad;
- break;
-#endif
-#ifdef CONFIG_ARCH_OMAP15XX
- case METHOD_GPIO_1510:
- reg += OMAP1510_GPIO_INT_CONTROL;
- l = __raw_readl(reg);
- if ((trigger & IRQ_TYPE_SENSE_MASK) == IRQ_TYPE_EDGE_BOTH)
- bank->toggle_mask |= 1 << gpio;
- if (trigger & IRQ_TYPE_EDGE_RISING)
- l |= 1 << gpio;
- else if (trigger & IRQ_TYPE_EDGE_FALLING)
- l &= ~(1 << gpio);
- else
- goto bad;
- break;
-#endif
-#ifdef CONFIG_ARCH_OMAP16XX
- case METHOD_GPIO_1610:
+ return -EINVAL;
+
+ __raw_writel(l, reg);
+ } else if (bank->regs->edgectrl1) {
if (gpio & 0x08)
- reg += OMAP1610_GPIO_EDGE_CTRL2;
+ reg += bank->regs->edgectrl2;
else
- reg += OMAP1610_GPIO_EDGE_CTRL1;
+ reg += bank->regs->edgectrl1;
+
gpio &= 0x07;
l = __raw_readl(reg);
l &= ~(3 << (gpio << 1));
@@ -361,40 +355,14 @@
l |= 2 << (gpio << 1);
if (trigger & IRQ_TYPE_EDGE_FALLING)
l |= 1 << (gpio << 1);
- if (trigger)
- /* Enable wake-up during idle for dynamic tick */
- __raw_writel(1 << gpio, bank->base + OMAP1610_GPIO_SET_WAKEUPENA);
- else
- __raw_writel(1 << gpio, bank->base + OMAP1610_GPIO_CLEAR_WAKEUPENA);
- break;
-#endif
-#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
- case METHOD_GPIO_7XX:
- reg += OMAP7XX_GPIO_INT_CONTROL;
- l = __raw_readl(reg);
- if ((trigger & IRQ_TYPE_SENSE_MASK) == IRQ_TYPE_EDGE_BOTH)
- bank->toggle_mask |= 1 << gpio;
- if (trigger & IRQ_TYPE_EDGE_RISING)
- l |= 1 << gpio;
- else if (trigger & IRQ_TYPE_EDGE_FALLING)
- l &= ~(1 << gpio);
- else
- goto bad;
- break;
-#endif
-#ifdef CONFIG_ARCH_OMAP2PLUS
- case METHOD_GPIO_24XX:
- case METHOD_GPIO_44XX:
- set_24xx_gpio_triggering(bank, gpio, trigger);
- return 0;
-#endif
- default:
- goto bad;
+
+ /* Enable wake-up during idle for dynamic tick */
+ _gpio_rmw(base, bank->regs->wkup_en, 1 << gpio, trigger);
+ bank->context.wake_en =
+ __raw_readl(bank->base + bank->regs->wkup_en);
+ __raw_writel(l, reg);
}
- __raw_writel(l, reg);
return 0;
-bad:
- return -EINVAL;
}
static int gpio_irq_type(struct irq_data *d, unsigned type)
@@ -412,12 +380,12 @@
if (type & ~IRQ_TYPE_SENSE_MASK)
return -EINVAL;
- /* OMAP1 allows only only edge triggering */
- if (!cpu_class_is_omap2()
- && (type & (IRQ_TYPE_LEVEL_LOW|IRQ_TYPE_LEVEL_HIGH)))
+ bank = irq_data_get_irq_chip_data(d);
+
+ if (!bank->regs->leveldetect0 &&
+ (type & (IRQ_TYPE_LEVEL_LOW|IRQ_TYPE_LEVEL_HIGH)))
return -EINVAL;
- bank = irq_data_get_irq_chip_data(d);
spin_lock_irqsave(&bank->lock, flags);
retval = _set_gpio_triggering(bank, GPIO_INDEX(bank, gpio), type);
spin_unlock_irqrestore(&bank->lock, flags);
@@ -484,6 +452,7 @@
}
__raw_writel(l, reg);
+ bank->context.irqenable1 = l;
}
static void _disable_gpio_irqbank(struct gpio_bank *bank, int gpio_mask)
@@ -504,6 +473,7 @@
}
__raw_writel(l, reg);
+ bank->context.irqenable1 = l;
}
static inline void _set_gpio_irqenable(struct gpio_bank *bank, int gpio, int enable)
@@ -567,38 +537,39 @@
struct gpio_bank *bank = container_of(chip, struct gpio_bank, chip);
unsigned long flags;
- spin_lock_irqsave(&bank->lock, flags);
+ /*
+ * If this is the first gpio_request for the bank,
+ * enable the bank module.
+ */
+ if (!bank->mod_usage)
+ pm_runtime_get_sync(bank->dev);
+ spin_lock_irqsave(&bank->lock, flags);
/* Set trigger to none. You need to enable the desired trigger with
* request_irq() or set_irq_type().
*/
_set_gpio_triggering(bank, offset, IRQ_TYPE_NONE);
-#ifdef CONFIG_ARCH_OMAP15XX
- if (bank->method == METHOD_GPIO_1510) {
- void __iomem *reg;
+ if (bank->regs->pinctrl) {
+ void __iomem *reg = bank->base + bank->regs->pinctrl;
/* Claim the pin for MPU */
- reg = bank->base + OMAP1510_GPIO_PIN_CONTROL;
__raw_writel(__raw_readl(reg) | (1 << offset), reg);
}
-#endif
- if (!cpu_class_is_omap1()) {
- if (!bank->mod_usage) {
- void __iomem *reg = bank->base;
- u32 ctrl;
- if (cpu_is_omap24xx() || cpu_is_omap34xx())
- reg += OMAP24XX_GPIO_CTRL;
- else if (cpu_is_omap44xx())
- reg += OMAP4_GPIO_CTRL;
- ctrl = __raw_readl(reg);
- /* Module is enabled, clocks are not gated */
- ctrl &= 0xFFFFFFFE;
- __raw_writel(ctrl, reg);
- }
- bank->mod_usage |= 1 << offset;
+ if (bank->regs->ctrl && !bank->mod_usage) {
+ void __iomem *reg = bank->base + bank->regs->ctrl;
+ u32 ctrl;
+
+ ctrl = __raw_readl(reg);
+ /* Module is enabled, clocks are not gated */
+ ctrl &= ~GPIO_MOD_CTRL_BIT;
+ __raw_writel(ctrl, reg);
+ bank->context.ctrl = ctrl;
}
+
+ bank->mod_usage |= 1 << offset;
+
spin_unlock_irqrestore(&bank->lock, flags);
return 0;
@@ -607,48 +578,40 @@
static void omap_gpio_free(struct gpio_chip *chip, unsigned offset)
{
struct gpio_bank *bank = container_of(chip, struct gpio_bank, chip);
+ void __iomem *base = bank->base;
unsigned long flags;
spin_lock_irqsave(&bank->lock, flags);
-#ifdef CONFIG_ARCH_OMAP16XX
- if (bank->method == METHOD_GPIO_1610) {
- /* Disable wake-up during idle for dynamic tick */
- void __iomem *reg = bank->base + OMAP1610_GPIO_CLEAR_WAKEUPENA;
- __raw_writel(1 << offset, reg);
- }
-#endif
-#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
- if (bank->method == METHOD_GPIO_24XX) {
- /* Disable wake-up during idle for dynamic tick */
- void __iomem *reg = bank->base + OMAP24XX_GPIO_CLEARWKUENA;
- __raw_writel(1 << offset, reg);
- }
-#endif
-#ifdef CONFIG_ARCH_OMAP4
- if (bank->method == METHOD_GPIO_44XX) {
- /* Disable wake-up during idle for dynamic tick */
- void __iomem *reg = bank->base + OMAP4_GPIO_IRQWAKEN0;
- __raw_writel(1 << offset, reg);
- }
-#endif
- if (!cpu_class_is_omap1()) {
- bank->mod_usage &= ~(1 << offset);
- if (!bank->mod_usage) {
- void __iomem *reg = bank->base;
- u32 ctrl;
- if (cpu_is_omap24xx() || cpu_is_omap34xx())
- reg += OMAP24XX_GPIO_CTRL;
- else if (cpu_is_omap44xx())
- reg += OMAP4_GPIO_CTRL;
- ctrl = __raw_readl(reg);
- /* Module is disabled, clocks are gated */
- ctrl |= 1;
- __raw_writel(ctrl, reg);
- }
+ if (bank->regs->wkup_en) {
+ /* Disable wake-up during idle for dynamic tick */
+ _gpio_rmw(base, bank->regs->wkup_en, 1 << offset, 0);
+ bank->context.wake_en =
+ __raw_readl(bank->base + bank->regs->wkup_en);
}
+
+ bank->mod_usage &= ~(1 << offset);
+
+ if (bank->regs->ctrl && !bank->mod_usage) {
+ void __iomem *reg = bank->base + bank->regs->ctrl;
+ u32 ctrl;
+
+ ctrl = __raw_readl(reg);
+ /* Module is disabled, clocks are gated */
+ ctrl |= GPIO_MOD_CTRL_BIT;
+ __raw_writel(ctrl, reg);
+ bank->context.ctrl = ctrl;
+ }
+
_reset_gpio(bank, bank->chip.base + offset);
spin_unlock_irqrestore(&bank->lock, flags);
+
+ /*
+ * If this is the last gpio to be freed in the bank,
+ * disable the bank module.
+ */
+ if (!bank->mod_usage)
+ pm_runtime_put(bank->dev);
}
/*
@@ -674,6 +637,7 @@
bank = irq_get_handler_data(irq);
isr_reg = bank->base + bank->regs->irqstatus;
+ pm_runtime_get_sync(bank->dev);
if (WARN_ON(!isr_reg))
goto exit;
@@ -685,12 +649,8 @@
enabled = _get_gpio_irqbank_mask(bank);
isr_saved = isr = __raw_readl(isr_reg) & enabled;
- if (cpu_is_omap15xx() && (bank->method == METHOD_MPUIO))
- isr &= 0x0000ffff;
-
- if (cpu_class_is_omap2()) {
+ if (bank->level_mask)
level_mask = bank->level_mask & enabled;
- }
/* clear edge sensitive interrupts before handler(s) are
called so that we don't miss any interrupt occurred while
@@ -718,7 +678,6 @@
if (!(isr & 1))
continue;
-#ifdef CONFIG_ARCH_OMAP1
/*
* Some chips can't respond to both rising and falling
* at the same time. If this irq was requested with
@@ -728,7 +687,6 @@
*/
if (bank->toggle_mask & (1 << gpio_index))
_toggle_gpio_edge_triggering(bank, gpio_index);
-#endif
generic_handle_irq(gpio_irq);
}
@@ -740,6 +698,7 @@
exit:
if (!unmasked)
chained_irq_exit(chip, desc);
+ pm_runtime_put(bank->dev);
}
static void gpio_irq_shutdown(struct irq_data *d)
@@ -808,14 +767,6 @@
/*---------------------------------------------------------------------*/
-#ifdef CONFIG_ARCH_OMAP1
-
-#define bank_is_mpuio(bank) ((bank)->method == METHOD_MPUIO)
-
-#ifdef CONFIG_ARCH_OMAP16XX
-
-#include <linux/platform_device.h>
-
static int omap_mpuio_suspend_noirq(struct device *dev)
{
struct platform_device *pdev = to_platform_device(dev);
@@ -869,32 +820,16 @@
/* could list the /proc/iomem resources */
};
-static inline void mpuio_init(void)
+static inline void mpuio_init(struct gpio_bank *bank)
{
- struct gpio_bank *bank = &gpio_bank[0];
platform_set_drvdata(&omap_mpuio_device, bank);
if (platform_driver_register(&omap_mpuio_driver) == 0)
(void) platform_device_register(&omap_mpuio_device);
}
-#else
-static inline void mpuio_init(void) {}
-#endif /* 16xx */
-
-#else
-
-#define bank_is_mpuio(bank) 0
-static inline void mpuio_init(void) {}
-
-#endif
-
/*---------------------------------------------------------------------*/
-/* REVISIT these are stupid implementations! replace by ones that
- * don't switch on METHOD_* and which mostly avoid spinlocks
- */
-
static int gpio_input(struct gpio_chip *chip, unsigned offset)
{
struct gpio_bank *bank;
@@ -1007,78 +942,32 @@
*/
static struct lock_class_key gpio_lock_class;
-static inline int init_gpio_info(struct platform_device *pdev)
+static void omap_gpio_mod_init(struct gpio_bank *bank)
{
- /* TODO: Analyze removing gpio_bank_count usage from driver code */
- gpio_bank = kzalloc(gpio_bank_count * sizeof(struct gpio_bank),
- GFP_KERNEL);
- if (!gpio_bank) {
- dev_err(&pdev->dev, "Memory alloc failed for gpio_bank\n");
- return -ENOMEM;
+ void __iomem *base = bank->base;
+ u32 l = 0xffffffff;
+
+ if (bank->width == 16)
+ l = 0xffff;
+
+ if (bank->is_mpuio) {
+ __raw_writel(l, bank->base + bank->regs->irqenable);
+ return;
}
- return 0;
-}
-/* TODO: Cleanup cpu_is_* checks */
-static void omap_gpio_mod_init(struct gpio_bank *bank, int id)
-{
- if (cpu_class_is_omap2()) {
- if (cpu_is_omap44xx()) {
- __raw_writel(0xffffffff, bank->base +
- OMAP4_GPIO_IRQSTATUSCLR0);
- __raw_writel(0x00000000, bank->base +
- OMAP4_GPIO_DEBOUNCENABLE);
- /* Initialize interface clk ungated, module enabled */
- __raw_writel(0, bank->base + OMAP4_GPIO_CTRL);
- } else if (cpu_is_omap34xx()) {
- __raw_writel(0x00000000, bank->base +
- OMAP24XX_GPIO_IRQENABLE1);
- __raw_writel(0xffffffff, bank->base +
- OMAP24XX_GPIO_IRQSTATUS1);
- __raw_writel(0x00000000, bank->base +
- OMAP24XX_GPIO_DEBOUNCE_EN);
+ _gpio_rmw(base, bank->regs->irqenable, l, bank->regs->irqenable_inv);
+ _gpio_rmw(base, bank->regs->irqstatus, l,
+ bank->regs->irqenable_inv == false);
+ _gpio_rmw(base, bank->regs->irqenable, l, bank->regs->debounce_en != 0);
+ _gpio_rmw(base, bank->regs->irqenable, l, bank->regs->ctrl != 0);
+ if (bank->regs->debounce_en)
+ _gpio_rmw(base, bank->regs->debounce_en, 0, 1);
- /* Initialize interface clk ungated, module enabled */
- __raw_writel(0, bank->base + OMAP24XX_GPIO_CTRL);
- } else if (cpu_is_omap24xx()) {
- static const u32 non_wakeup_gpios[] = {
- 0xe203ffc0, 0x08700040
- };
- if (id < ARRAY_SIZE(non_wakeup_gpios))
- bank->non_wakeup_gpios = non_wakeup_gpios[id];
- }
- } else if (cpu_class_is_omap1()) {
- if (bank_is_mpuio(bank))
- __raw_writew(0xffff, bank->base +
- OMAP_MPUIO_GPIO_MASKIT / bank->stride);
- if (cpu_is_omap15xx() && bank->method == METHOD_GPIO_1510) {
- __raw_writew(0xffff, bank->base
- + OMAP1510_GPIO_INT_MASK);
- __raw_writew(0x0000, bank->base
- + OMAP1510_GPIO_INT_STATUS);
- }
- if (cpu_is_omap16xx() && bank->method == METHOD_GPIO_1610) {
- __raw_writew(0x0000, bank->base
- + OMAP1610_GPIO_IRQENABLE1);
- __raw_writew(0xffff, bank->base
- + OMAP1610_GPIO_IRQSTATUS1);
- __raw_writew(0x0014, bank->base
- + OMAP1610_GPIO_SYSCONFIG);
-
- /*
- * Enable system clock for GPIO module.
- * The CAM_CLK_CTRL *is* really the right place.
- */
- omap_writel(omap_readl(ULPD_CAM_CLK_CTRL) | 0x04,
- ULPD_CAM_CLK_CTRL);
- }
- if (cpu_is_omap7xx() && bank->method == METHOD_GPIO_7XX) {
- __raw_writel(0xffffffff, bank->base
- + OMAP7XX_GPIO_INT_MASK);
- __raw_writel(0x00000000, bank->base
- + OMAP7XX_GPIO_INT_STATUS);
- }
- }
+ /* Save OE default value (0xffffffff) in the context */
+ bank->context.oe = __raw_readl(bank->base + bank->regs->direction);
+ /* Initialize interface clk ungated, module enabled */
+ if (bank->regs->ctrl)
+ _gpio_rmw(base, bank->regs->ctrl, 0, 1);
}
static __init void
@@ -1101,8 +990,8 @@
ct->chip.irq_mask = irq_gc_mask_set_bit;
ct->chip.irq_unmask = irq_gc_mask_clr_bit;
ct->chip.irq_set_type = gpio_irq_type;
- /* REVISIT: assuming only 16xx supports MPUIO wake events */
- if (cpu_is_omap16xx())
+
+ if (bank->regs->wkup_en)
ct->chip.irq_set_wake = gpio_wake_enable,
ct->regs.mask = OMAP_MPUIO_GPIO_INT / bank->stride;
@@ -1115,7 +1004,6 @@
int j;
static int gpio;
- bank->mod_usage = 0;
/*
* REVISIT eventually switch from OMAP-specific gpio structs
* over to the generic ones
@@ -1128,11 +1016,10 @@
bank->chip.set_debounce = gpio_debounce;
bank->chip.set = gpio_set;
bank->chip.to_irq = gpio_2irq;
- if (bank_is_mpuio(bank)) {
+ if (bank->is_mpuio) {
bank->chip.label = "mpuio";
-#ifdef CONFIG_ARCH_OMAP16XX
- bank->chip.dev = &omap_mpuio_device.dev;
-#endif
+ if (bank->regs->wkup_en)
+ bank->chip.dev = &omap_mpuio_device.dev;
bank->chip.base = OMAP_MPUIO(0);
} else {
bank->chip.label = "gpio";
@@ -1147,7 +1034,7 @@
j < bank->virtual_irq_start + bank->width; j++) {
irq_set_lockdep_class(j, &gpio_lock_class);
irq_set_chip_data(j, bank);
- if (bank_is_mpuio(bank)) {
+ if (bank->is_mpuio) {
omap_mpuio_alloc_gc(bank, j, bank->width);
} else {
irq_set_chip(j, &gpio_irq_chip);
@@ -1161,42 +1048,44 @@
static int __devinit omap_gpio_probe(struct platform_device *pdev)
{
- static int gpio_init_done;
struct omap_gpio_platform_data *pdata;
struct resource *res;
- int id;
struct gpio_bank *bank;
+ int ret = 0;
- if (!pdev->dev.platform_data)
- return -EINVAL;
-
- pdata = pdev->dev.platform_data;
-
- if (!gpio_init_done) {
- int ret;
-
- ret = init_gpio_info(pdev);
- if (ret)
- return ret;
+ if (!pdev->dev.platform_data) {
+ ret = -EINVAL;
+ goto err_exit;
}
- id = pdev->id;
- bank = &gpio_bank[id];
+ bank = kzalloc(sizeof(struct gpio_bank), GFP_KERNEL);
+ if (!bank) {
+ dev_err(&pdev->dev, "Memory alloc failed for gpio_bank\n");
+ ret = -ENOMEM;
+ goto err_exit;
+ }
res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
if (unlikely(!res)) {
- dev_err(&pdev->dev, "GPIO Bank %i Invalid IRQ resource\n", id);
- return -ENODEV;
+ dev_err(&pdev->dev, "GPIO Bank %i Invalid IRQ resource\n",
+ pdev->id);
+ ret = -ENODEV;
+ goto err_free;
}
bank->irq = res->start;
+ bank->id = pdev->id;
+
+ pdata = pdev->dev.platform_data;
bank->virtual_irq_start = pdata->virtual_irq_start;
- bank->method = pdata->bank_type;
bank->dev = &pdev->dev;
bank->dbck_flag = pdata->dbck_flag;
bank->stride = pdata->bank_stride;
bank->width = pdata->bank_width;
-
+ bank->is_mpuio = pdata->is_mpuio;
+ bank->non_wakeup_gpios = pdata->non_wakeup_gpios;
+ bank->loses_context = pdata->loses_context;
+ bank->get_context_loss_count = pdata->get_context_loss_count;
bank->regs = pdata->regs;
if (bank->regs->set_dataout && bank->regs->clr_dataout)
@@ -1209,369 +1098,310 @@
/* Static mapping, never released */
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (unlikely(!res)) {
- dev_err(&pdev->dev, "GPIO Bank %i Invalid mem resource\n", id);
- return -ENODEV;
+ dev_err(&pdev->dev, "GPIO Bank %i Invalid mem resource\n",
+ pdev->id);
+ ret = -ENODEV;
+ goto err_free;
}
bank->base = ioremap(res->start, resource_size(res));
if (!bank->base) {
- dev_err(&pdev->dev, "Could not ioremap gpio bank%i\n", id);
- return -ENOMEM;
+ dev_err(&pdev->dev, "Could not ioremap gpio bank%i\n",
+ pdev->id);
+ ret = -ENOMEM;
+ goto err_free;
}
+ platform_set_drvdata(pdev, bank);
+
pm_runtime_enable(bank->dev);
+ pm_runtime_irq_safe(bank->dev);
pm_runtime_get_sync(bank->dev);
- omap_gpio_mod_init(bank, id);
+ if (bank->is_mpuio)
+ mpuio_init(bank);
+
+ omap_gpio_mod_init(bank);
omap_gpio_chip_init(bank);
omap_gpio_show_rev(bank);
- if (!gpio_init_done)
- gpio_init_done = 1;
+ pm_runtime_put(bank->dev);
- return 0;
+ list_add_tail(&bank->node, &omap_gpio_list);
+
+ return ret;
+
+err_free:
+ kfree(bank);
+err_exit:
+ return ret;
}
-#if defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP2PLUS)
-static int omap_gpio_suspend(void)
-{
- int i;
-
- if (!cpu_class_is_omap2() && !cpu_is_omap16xx())
- return 0;
-
- for (i = 0; i < gpio_bank_count; i++) {
- struct gpio_bank *bank = &gpio_bank[i];
- void __iomem *wake_status;
- void __iomem *wake_clear;
- void __iomem *wake_set;
- unsigned long flags;
-
- switch (bank->method) {
-#ifdef CONFIG_ARCH_OMAP16XX
- case METHOD_GPIO_1610:
- wake_status = bank->base + OMAP1610_GPIO_WAKEUPENABLE;
- wake_clear = bank->base + OMAP1610_GPIO_CLEAR_WAKEUPENA;
- wake_set = bank->base + OMAP1610_GPIO_SET_WAKEUPENA;
- break;
-#endif
-#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
- case METHOD_GPIO_24XX:
- wake_status = bank->base + OMAP24XX_GPIO_WAKE_EN;
- wake_clear = bank->base + OMAP24XX_GPIO_CLEARWKUENA;
- wake_set = bank->base + OMAP24XX_GPIO_SETWKUENA;
- break;
-#endif
-#ifdef CONFIG_ARCH_OMAP4
- case METHOD_GPIO_44XX:
- wake_status = bank->base + OMAP4_GPIO_IRQWAKEN0;
- wake_clear = bank->base + OMAP4_GPIO_IRQWAKEN0;
- wake_set = bank->base + OMAP4_GPIO_IRQWAKEN0;
- break;
-#endif
- default:
- continue;
- }
-
- spin_lock_irqsave(&bank->lock, flags);
- bank->saved_wakeup = __raw_readl(wake_status);
- __raw_writel(0xffffffff, wake_clear);
- __raw_writel(bank->suspend_wakeup, wake_set);
- spin_unlock_irqrestore(&bank->lock, flags);
- }
-
- return 0;
-}
-
-static void omap_gpio_resume(void)
-{
- int i;
-
- if (!cpu_class_is_omap2() && !cpu_is_omap16xx())
- return;
-
- for (i = 0; i < gpio_bank_count; i++) {
- struct gpio_bank *bank = &gpio_bank[i];
- void __iomem *wake_clear;
- void __iomem *wake_set;
- unsigned long flags;
-
- switch (bank->method) {
-#ifdef CONFIG_ARCH_OMAP16XX
- case METHOD_GPIO_1610:
- wake_clear = bank->base + OMAP1610_GPIO_CLEAR_WAKEUPENA;
- wake_set = bank->base + OMAP1610_GPIO_SET_WAKEUPENA;
- break;
-#endif
-#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
- case METHOD_GPIO_24XX:
- wake_clear = bank->base + OMAP24XX_GPIO_CLEARWKUENA;
- wake_set = bank->base + OMAP24XX_GPIO_SETWKUENA;
- break;
-#endif
-#ifdef CONFIG_ARCH_OMAP4
- case METHOD_GPIO_44XX:
- wake_clear = bank->base + OMAP4_GPIO_IRQWAKEN0;
- wake_set = bank->base + OMAP4_GPIO_IRQWAKEN0;
- break;
-#endif
- default:
- continue;
- }
-
- spin_lock_irqsave(&bank->lock, flags);
- __raw_writel(0xffffffff, wake_clear);
- __raw_writel(bank->saved_wakeup, wake_set);
- spin_unlock_irqrestore(&bank->lock, flags);
- }
-}
-
-static struct syscore_ops omap_gpio_syscore_ops = {
- .suspend = omap_gpio_suspend,
- .resume = omap_gpio_resume,
-};
-
-#endif
-
#ifdef CONFIG_ARCH_OMAP2PLUS
-static int workaround_enabled;
-
-void omap2_gpio_prepare_for_idle(int off_mode)
+#if defined(CONFIG_PM_SLEEP)
+static int omap_gpio_suspend(struct device *dev)
{
- int i, c = 0;
- int min = 0;
+ struct platform_device *pdev = to_platform_device(dev);
+ struct gpio_bank *bank = platform_get_drvdata(pdev);
+ void __iomem *base = bank->base;
+ void __iomem *wakeup_enable;
+ unsigned long flags;
- if (cpu_is_omap34xx())
- min = 1;
+ if (!bank->mod_usage || !bank->loses_context)
+ return 0;
- for (i = min; i < gpio_bank_count; i++) {
- struct gpio_bank *bank = &gpio_bank[i];
- u32 l1 = 0, l2 = 0;
- int j;
+ if (!bank->regs->wkup_en || !bank->suspend_wakeup)
+ return 0;
- for (j = 0; j < hweight_long(bank->dbck_enable_mask); j++)
- clk_disable(bank->dbck);
+ wakeup_enable = bank->base + bank->regs->wkup_en;
- if (!off_mode)
- continue;
+ spin_lock_irqsave(&bank->lock, flags);
+ bank->saved_wakeup = __raw_readl(wakeup_enable);
+ _gpio_rmw(base, bank->regs->wkup_en, 0xffffffff, 0);
+ _gpio_rmw(base, bank->regs->wkup_en, bank->suspend_wakeup, 1);
+ spin_unlock_irqrestore(&bank->lock, flags);
- /* If going to OFF, remove triggering for all
- * non-wakeup GPIOs. Otherwise spurious IRQs will be
- * generated. See OMAP2420 Errata item 1.101. */
- if (!(bank->enabled_non_wakeup_gpios))
- continue;
+ return 0;
+}
+
+static int omap_gpio_resume(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct gpio_bank *bank = platform_get_drvdata(pdev);
+ void __iomem *base = bank->base;
+ unsigned long flags;
+
+ if (!bank->mod_usage || !bank->loses_context)
+ return 0;
+
+ if (!bank->regs->wkup_en || !bank->saved_wakeup)
+ return 0;
+
+ spin_lock_irqsave(&bank->lock, flags);
+ _gpio_rmw(base, bank->regs->wkup_en, 0xffffffff, 0);
+ _gpio_rmw(base, bank->regs->wkup_en, bank->saved_wakeup, 1);
+ spin_unlock_irqrestore(&bank->lock, flags);
+
+ return 0;
+}
+#endif /* CONFIG_PM_SLEEP */
+
+#if defined(CONFIG_PM_RUNTIME)
+static void omap_gpio_restore_context(struct gpio_bank *bank);
+
+static int omap_gpio_runtime_suspend(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct gpio_bank *bank = platform_get_drvdata(pdev);
+ u32 l1 = 0, l2 = 0;
+ unsigned long flags;
+
+ spin_lock_irqsave(&bank->lock, flags);
+ if (bank->power_mode != OFF_MODE) {
+ bank->power_mode = 0;
+ goto update_gpio_context_count;
+ }
+ /*
+ * If going to OFF, remove triggering for all
+ * non-wakeup GPIOs. Otherwise spurious IRQs will be
+ * generated. See OMAP2420 Errata item 1.101.
+ */
+ if (!(bank->enabled_non_wakeup_gpios))
+ goto update_gpio_context_count;
+
+ bank->saved_datain = __raw_readl(bank->base +
+ bank->regs->datain);
+ l1 = __raw_readl(bank->base + bank->regs->fallingdetect);
+ l2 = __raw_readl(bank->base + bank->regs->risingdetect);
+
+ bank->saved_fallingdetect = l1;
+ bank->saved_risingdetect = l2;
+ l1 &= ~bank->enabled_non_wakeup_gpios;
+ l2 &= ~bank->enabled_non_wakeup_gpios;
+
+ __raw_writel(l1, bank->base + bank->regs->fallingdetect);
+ __raw_writel(l2, bank->base + bank->regs->risingdetect);
+
+ bank->workaround_enabled = true;
+
+update_gpio_context_count:
+ if (bank->get_context_loss_count)
+ bank->context_loss_count =
+ bank->get_context_loss_count(bank->dev);
+
+ _gpio_dbck_disable(bank);
+ spin_unlock_irqrestore(&bank->lock, flags);
+
+ return 0;
+}
+
+static int omap_gpio_runtime_resume(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct gpio_bank *bank = platform_get_drvdata(pdev);
+ int context_lost_cnt_after;
+ u32 l = 0, gen, gen0, gen1;
+ unsigned long flags;
+
+ spin_lock_irqsave(&bank->lock, flags);
+ _gpio_dbck_enable(bank);
+ if (!bank->enabled_non_wakeup_gpios || !bank->workaround_enabled) {
+ spin_unlock_irqrestore(&bank->lock, flags);
+ return 0;
+ }
+
+ if (bank->get_context_loss_count) {
+ context_lost_cnt_after =
+ bank->get_context_loss_count(bank->dev);
+ if (context_lost_cnt_after != bank->context_loss_count ||
+ !context_lost_cnt_after) {
+ omap_gpio_restore_context(bank);
+ } else {
+ spin_unlock_irqrestore(&bank->lock, flags);
+ return 0;
+ }
+ }
+
+ __raw_writel(bank->saved_fallingdetect,
+ bank->base + bank->regs->fallingdetect);
+ __raw_writel(bank->saved_risingdetect,
+ bank->base + bank->regs->risingdetect);
+ l = __raw_readl(bank->base + bank->regs->datain);
+
+ /*
+ * Check if any of the non-wakeup interrupt GPIOs have changed
+ * state. If so, generate an IRQ by software. This is
+ * horribly racy, but it's the best we can do to work around
+ * this silicon bug.
+ */
+ l ^= bank->saved_datain;
+ l &= bank->enabled_non_wakeup_gpios;
+
+ /*
+ * No need to generate IRQs for the rising edge for gpio IRQs
+ * configured with falling edge only; and vice versa.
+ */
+ gen0 = l & bank->saved_fallingdetect;
+ gen0 &= bank->saved_datain;
+
+ gen1 = l & bank->saved_risingdetect;
+ gen1 &= ~(bank->saved_datain);
+
+ /* FIXME: Consider GPIO IRQs with level detections properly! */
+ gen = l & (~(bank->saved_fallingdetect) & ~(bank->saved_risingdetect));
+ /* Consider all GPIO IRQs needed to be updated */
+ gen |= gen0 | gen1;
+
+ if (gen) {
+ u32 old0, old1;
+
+ old0 = __raw_readl(bank->base + bank->regs->leveldetect0);
+ old1 = __raw_readl(bank->base + bank->regs->leveldetect1);
if (cpu_is_omap24xx() || cpu_is_omap34xx()) {
- bank->saved_datain = __raw_readl(bank->base +
- OMAP24XX_GPIO_DATAIN);
- l1 = __raw_readl(bank->base +
- OMAP24XX_GPIO_FALLINGDETECT);
- l2 = __raw_readl(bank->base +
- OMAP24XX_GPIO_RISINGDETECT);
+ __raw_writel(old0 | gen, bank->base +
+ bank->regs->leveldetect0);
+ __raw_writel(old1 | gen, bank->base +
+ bank->regs->leveldetect1);
}
if (cpu_is_omap44xx()) {
- bank->saved_datain = __raw_readl(bank->base +
- OMAP4_GPIO_DATAIN);
- l1 = __raw_readl(bank->base +
- OMAP4_GPIO_FALLINGDETECT);
- l2 = __raw_readl(bank->base +
- OMAP4_GPIO_RISINGDETECT);
+ __raw_writel(old0 | l, bank->base +
+ bank->regs->leveldetect0);
+ __raw_writel(old1 | l, bank->base +
+ bank->regs->leveldetect1);
}
-
- bank->saved_fallingdetect = l1;
- bank->saved_risingdetect = l2;
- l1 &= ~bank->enabled_non_wakeup_gpios;
- l2 &= ~bank->enabled_non_wakeup_gpios;
-
- if (cpu_is_omap24xx() || cpu_is_omap34xx()) {
- __raw_writel(l1, bank->base +
- OMAP24XX_GPIO_FALLINGDETECT);
- __raw_writel(l2, bank->base +
- OMAP24XX_GPIO_RISINGDETECT);
- }
-
- if (cpu_is_omap44xx()) {
- __raw_writel(l1, bank->base + OMAP4_GPIO_FALLINGDETECT);
- __raw_writel(l2, bank->base + OMAP4_GPIO_RISINGDETECT);
- }
-
- c++;
+ __raw_writel(old0, bank->base + bank->regs->leveldetect0);
+ __raw_writel(old1, bank->base + bank->regs->leveldetect1);
}
- if (!c) {
- workaround_enabled = 0;
- return;
+
+ bank->workaround_enabled = false;
+ spin_unlock_irqrestore(&bank->lock, flags);
+
+ return 0;
+}
+#endif /* CONFIG_PM_RUNTIME */
+
+void omap2_gpio_prepare_for_idle(int pwr_mode)
+{
+ struct gpio_bank *bank;
+
+ list_for_each_entry(bank, &omap_gpio_list, node) {
+ if (!bank->mod_usage || !bank->loses_context)
+ continue;
+
+ bank->power_mode = pwr_mode;
+
+ pm_runtime_put_sync_suspend(bank->dev);
}
- workaround_enabled = 1;
}
void omap2_gpio_resume_after_idle(void)
{
- int i;
- int min = 0;
+ struct gpio_bank *bank;
- if (cpu_is_omap34xx())
- min = 1;
- for (i = min; i < gpio_bank_count; i++) {
- struct gpio_bank *bank = &gpio_bank[i];
- u32 l = 0, gen, gen0, gen1;
- int j;
-
- for (j = 0; j < hweight_long(bank->dbck_enable_mask); j++)
- clk_enable(bank->dbck);
-
- if (!workaround_enabled)
+ list_for_each_entry(bank, &omap_gpio_list, node) {
+ if (!bank->mod_usage || !bank->loses_context)
continue;
- if (!(bank->enabled_non_wakeup_gpios))
- continue;
-
- if (cpu_is_omap24xx() || cpu_is_omap34xx()) {
- __raw_writel(bank->saved_fallingdetect,
- bank->base + OMAP24XX_GPIO_FALLINGDETECT);
- __raw_writel(bank->saved_risingdetect,
- bank->base + OMAP24XX_GPIO_RISINGDETECT);
- l = __raw_readl(bank->base + OMAP24XX_GPIO_DATAIN);
- }
-
- if (cpu_is_omap44xx()) {
- __raw_writel(bank->saved_fallingdetect,
- bank->base + OMAP4_GPIO_FALLINGDETECT);
- __raw_writel(bank->saved_risingdetect,
- bank->base + OMAP4_GPIO_RISINGDETECT);
- l = __raw_readl(bank->base + OMAP4_GPIO_DATAIN);
- }
-
- /* Check if any of the non-wakeup interrupt GPIOs have changed
- * state. If so, generate an IRQ by software. This is
- * horribly racy, but it's the best we can do to work around
- * this silicon bug. */
- l ^= bank->saved_datain;
- l &= bank->enabled_non_wakeup_gpios;
-
- /*
- * No need to generate IRQs for the rising edge for gpio IRQs
- * configured with falling edge only; and vice versa.
- */
- gen0 = l & bank->saved_fallingdetect;
- gen0 &= bank->saved_datain;
-
- gen1 = l & bank->saved_risingdetect;
- gen1 &= ~(bank->saved_datain);
-
- /* FIXME: Consider GPIO IRQs with level detections properly! */
- gen = l & (~(bank->saved_fallingdetect) &
- ~(bank->saved_risingdetect));
- /* Consider all GPIO IRQs needed to be updated */
- gen |= gen0 | gen1;
-
- if (gen) {
- u32 old0, old1;
-
- if (cpu_is_omap24xx() || cpu_is_omap34xx()) {
- old0 = __raw_readl(bank->base +
- OMAP24XX_GPIO_LEVELDETECT0);
- old1 = __raw_readl(bank->base +
- OMAP24XX_GPIO_LEVELDETECT1);
- __raw_writel(old0 | gen, bank->base +
- OMAP24XX_GPIO_LEVELDETECT0);
- __raw_writel(old1 | gen, bank->base +
- OMAP24XX_GPIO_LEVELDETECT1);
- __raw_writel(old0, bank->base +
- OMAP24XX_GPIO_LEVELDETECT0);
- __raw_writel(old1, bank->base +
- OMAP24XX_GPIO_LEVELDETECT1);
- }
-
- if (cpu_is_omap44xx()) {
- old0 = __raw_readl(bank->base +
- OMAP4_GPIO_LEVELDETECT0);
- old1 = __raw_readl(bank->base +
- OMAP4_GPIO_LEVELDETECT1);
- __raw_writel(old0 | l, bank->base +
- OMAP4_GPIO_LEVELDETECT0);
- __raw_writel(old1 | l, bank->base +
- OMAP4_GPIO_LEVELDETECT1);
- __raw_writel(old0, bank->base +
- OMAP4_GPIO_LEVELDETECT0);
- __raw_writel(old1, bank->base +
- OMAP4_GPIO_LEVELDETECT1);
- }
- }
+ pm_runtime_get_sync(bank->dev);
}
-
}
+#if defined(CONFIG_PM_RUNTIME)
+static void omap_gpio_restore_context(struct gpio_bank *bank)
+{
+ __raw_writel(bank->context.wake_en,
+ bank->base + bank->regs->wkup_en);
+ __raw_writel(bank->context.ctrl, bank->base + bank->regs->ctrl);
+ __raw_writel(bank->context.leveldetect0,
+ bank->base + bank->regs->leveldetect0);
+ __raw_writel(bank->context.leveldetect1,
+ bank->base + bank->regs->leveldetect1);
+ __raw_writel(bank->context.risingdetect,
+ bank->base + bank->regs->risingdetect);
+ __raw_writel(bank->context.fallingdetect,
+ bank->base + bank->regs->fallingdetect);
+ if (bank->regs->set_dataout && bank->regs->clr_dataout)
+ __raw_writel(bank->context.dataout,
+ bank->base + bank->regs->set_dataout);
+ else
+ __raw_writel(bank->context.dataout,
+ bank->base + bank->regs->dataout);
+ __raw_writel(bank->context.oe, bank->base + bank->regs->direction);
+
+ if (bank->dbck_enable_mask) {
+ __raw_writel(bank->context.debounce, bank->base +
+ bank->regs->debounce);
+ __raw_writel(bank->context.debounce_en,
+ bank->base + bank->regs->debounce_en);
+ }
+
+ __raw_writel(bank->context.irqenable1,
+ bank->base + bank->regs->irqenable);
+ __raw_writel(bank->context.irqenable2,
+ bank->base + bank->regs->irqenable2);
+}
+#endif /* CONFIG_PM_RUNTIME */
+#else
+#define omap_gpio_suspend NULL
+#define omap_gpio_resume NULL
+#define omap_gpio_runtime_suspend NULL
+#define omap_gpio_runtime_resume NULL
#endif
-#ifdef CONFIG_ARCH_OMAP3
-/* save the registers of bank 2-6 */
-void omap_gpio_save_context(void)
-{
- int i;
-
- /* saving banks from 2-6 only since GPIO1 is in WKUP */
- for (i = 1; i < gpio_bank_count; i++) {
- struct gpio_bank *bank = &gpio_bank[i];
- gpio_context[i].irqenable1 =
- __raw_readl(bank->base + OMAP24XX_GPIO_IRQENABLE1);
- gpio_context[i].irqenable2 =
- __raw_readl(bank->base + OMAP24XX_GPIO_IRQENABLE2);
- gpio_context[i].wake_en =
- __raw_readl(bank->base + OMAP24XX_GPIO_WAKE_EN);
- gpio_context[i].ctrl =
- __raw_readl(bank->base + OMAP24XX_GPIO_CTRL);
- gpio_context[i].oe =
- __raw_readl(bank->base + OMAP24XX_GPIO_OE);
- gpio_context[i].leveldetect0 =
- __raw_readl(bank->base + OMAP24XX_GPIO_LEVELDETECT0);
- gpio_context[i].leveldetect1 =
- __raw_readl(bank->base + OMAP24XX_GPIO_LEVELDETECT1);
- gpio_context[i].risingdetect =
- __raw_readl(bank->base + OMAP24XX_GPIO_RISINGDETECT);
- gpio_context[i].fallingdetect =
- __raw_readl(bank->base + OMAP24XX_GPIO_FALLINGDETECT);
- gpio_context[i].dataout =
- __raw_readl(bank->base + OMAP24XX_GPIO_DATAOUT);
- }
-}
-
-/* restore the required registers of bank 2-6 */
-void omap_gpio_restore_context(void)
-{
- int i;
-
- for (i = 1; i < gpio_bank_count; i++) {
- struct gpio_bank *bank = &gpio_bank[i];
- __raw_writel(gpio_context[i].irqenable1,
- bank->base + OMAP24XX_GPIO_IRQENABLE1);
- __raw_writel(gpio_context[i].irqenable2,
- bank->base + OMAP24XX_GPIO_IRQENABLE2);
- __raw_writel(gpio_context[i].wake_en,
- bank->base + OMAP24XX_GPIO_WAKE_EN);
- __raw_writel(gpio_context[i].ctrl,
- bank->base + OMAP24XX_GPIO_CTRL);
- __raw_writel(gpio_context[i].oe,
- bank->base + OMAP24XX_GPIO_OE);
- __raw_writel(gpio_context[i].leveldetect0,
- bank->base + OMAP24XX_GPIO_LEVELDETECT0);
- __raw_writel(gpio_context[i].leveldetect1,
- bank->base + OMAP24XX_GPIO_LEVELDETECT1);
- __raw_writel(gpio_context[i].risingdetect,
- bank->base + OMAP24XX_GPIO_RISINGDETECT);
- __raw_writel(gpio_context[i].fallingdetect,
- bank->base + OMAP24XX_GPIO_FALLINGDETECT);
- __raw_writel(gpio_context[i].dataout,
- bank->base + OMAP24XX_GPIO_DATAOUT);
- }
-}
-#endif
+static const struct dev_pm_ops gpio_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(omap_gpio_suspend, omap_gpio_resume)
+ SET_RUNTIME_PM_OPS(omap_gpio_runtime_suspend, omap_gpio_runtime_resume,
+ NULL)
+};
static struct platform_driver omap_gpio_driver = {
.probe = omap_gpio_probe,
.driver = {
.name = "omap_gpio",
+ .pm = &gpio_pm_ops,
},
};
@@ -1585,17 +1415,3 @@
return platform_driver_register(&omap_gpio_driver);
}
postcore_initcall(omap_gpio_drv_reg);
-
-static int __init omap_gpio_sysinit(void)
-{
- mpuio_init();
-
-#if defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP2PLUS)
- if (cpu_is_omap16xx() || cpu_class_is_omap2())
- register_syscore_ops(&omap_gpio_syscore_ops);
-#endif
-
- return 0;
-}
-
-arch_initcall(omap_gpio_sysinit);
diff --git a/drivers/gpio/gpio-pl061.c b/drivers/gpio/gpio-pl061.c
index 77c9cc7..b4b5da4 100644
--- a/drivers/gpio/gpio-pl061.c
+++ b/drivers/gpio/gpio-pl061.c
@@ -352,7 +352,12 @@
return 0;
}
-static SIMPLE_DEV_PM_OPS(pl061_dev_pm_ops, pl061_suspend, pl061_resume);
+static const struct dev_pm_ops pl061_dev_pm_ops = {
+ .suspend = pl061_suspend,
+ .resume = pl061_resume,
+ .freeze = pl061_suspend,
+ .restore = pl061_resume,
+};
#endif
static struct amba_id pl061_ids[] = {
diff --git a/drivers/gpio/gpio-sodaville.c b/drivers/gpio/gpio-sodaville.c
new file mode 100644
index 0000000..9ba15d3
--- /dev/null
+++ b/drivers/gpio/gpio-sodaville.c
@@ -0,0 +1,302 @@
+/*
+ * GPIO interface for Intel Sodaville SoCs.
+ *
+ * Copyright (c) 2010, 2011 Intel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License 2 as published
+ * by the Free Software Foundation.
+ *
+ */
+
+#include <linux/errno.h>
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+#include <linux/of_irq.h>
+#include <linux/basic_mmio_gpio.h>
+
+#define DRV_NAME "sdv_gpio"
+#define SDV_NUM_PUB_GPIOS 12
+#define PCI_DEVICE_ID_SDV_GPIO 0x2e67
+#define GPIO_BAR 0
+
+#define GPOUTR 0x00
+#define GPOER 0x04
+#define GPINR 0x08
+
+#define GPSTR 0x0c
+#define GPIT1R0 0x10
+#define GPIO_INT 0x14
+#define GPIT1R1 0x18
+
+#define GPMUXCTL 0x1c
+
+struct sdv_gpio_chip_data {
+ int irq_base;
+ void __iomem *gpio_pub_base;
+ struct irq_domain id;
+ struct irq_chip_generic *gc;
+ struct bgpio_chip bgpio;
+};
+
+static int sdv_gpio_pub_set_type(struct irq_data *d, unsigned int type)
+{
+ struct irq_chip_generic *gc = irq_data_get_irq_chip_data(d);
+ struct sdv_gpio_chip_data *sd = gc->private;
+ void __iomem *type_reg;
+ u32 irq_offs = d->irq - sd->irq_base;
+ u32 reg;
+
+ if (irq_offs < 8)
+ type_reg = sd->gpio_pub_base + GPIT1R0;
+ else
+ type_reg = sd->gpio_pub_base + GPIT1R1;
+
+ reg = readl(type_reg);
+
+ switch (type) {
+ case IRQ_TYPE_LEVEL_HIGH:
+ reg &= ~BIT(4 * (irq_offs % 8));
+ break;
+
+ case IRQ_TYPE_LEVEL_LOW:
+ reg |= BIT(4 * (irq_offs % 8));
+ break;
+
+ default:
+ return -EINVAL;
+ }
+
+ writel(reg, type_reg);
+ return 0;
+}
+
+static irqreturn_t sdv_gpio_pub_irq_handler(int irq, void *data)
+{
+ struct sdv_gpio_chip_data *sd = data;
+ u32 irq_stat = readl(sd->gpio_pub_base + GPSTR);
+
+ irq_stat &= readl(sd->gpio_pub_base + GPIO_INT);
+ if (!irq_stat)
+ return IRQ_NONE;
+
+ while (irq_stat) {
+ u32 irq_bit = __fls(irq_stat);
+
+ irq_stat &= ~BIT(irq_bit);
+ generic_handle_irq(sd->irq_base + irq_bit);
+ }
+
+ return IRQ_HANDLED;
+}
+
+static int sdv_xlate(struct irq_domain *h, struct device_node *node,
+ const u32 *intspec, u32 intsize, irq_hw_number_t *out_hwirq,
+ u32 *out_type)
+{
+ u32 line, type;
+
+ if (node != h->of_node)
+ return -EINVAL;
+
+ if (intsize < 2)
+ return -EINVAL;
+
+ line = *intspec;
+ *out_hwirq = line;
+
+ intspec++;
+ type = *intspec;
+
+ switch (type) {
+ case IRQ_TYPE_LEVEL_LOW:
+ case IRQ_TYPE_LEVEL_HIGH:
+ *out_type = type;
+ break;
+ default:
+ return -EINVAL;
+ }
+ return 0;
+}
+
+static struct irq_domain_ops irq_domain_sdv_ops = {
+ .dt_translate = sdv_xlate,
+};
+
+static __devinit int sdv_register_irqsupport(struct sdv_gpio_chip_data *sd,
+ struct pci_dev *pdev)
+{
+ struct irq_chip_type *ct;
+ int ret;
+
+ sd->irq_base = irq_alloc_descs(-1, 0, SDV_NUM_PUB_GPIOS, -1);
+ if (sd->irq_base < 0)
+ return sd->irq_base;
+
+ /* mask + ACK all interrupt sources */
+ writel(0, sd->gpio_pub_base + GPIO_INT);
+ writel((1 << 11) - 1, sd->gpio_pub_base + GPSTR);
+
+ ret = request_irq(pdev->irq, sdv_gpio_pub_irq_handler, IRQF_SHARED,
+ "sdv_gpio", sd);
+ if (ret)
+ goto out_free_desc;
+
+ sd->id.irq_base = sd->irq_base;
+ sd->id.of_node = of_node_get(pdev->dev.of_node);
+ sd->id.ops = &irq_domain_sdv_ops;
+
+ /*
+ * This gpio irq controller latches level irqs. Testing shows that if
+ * we unmask & ACK the IRQ before the source of the interrupt is gone
+ * then the interrupt is active again.
+ */
+ sd->gc = irq_alloc_generic_chip("sdv-gpio", 1, sd->irq_base,
+ sd->gpio_pub_base, handle_fasteoi_irq);
+ if (!sd->gc) {
+ ret = -ENOMEM;
+ goto out_free_irq;
+ }
+
+ sd->gc->private = sd;
+ ct = sd->gc->chip_types;
+ ct->type = IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_LEVEL_LOW;
+ ct->regs.eoi = GPSTR;
+ ct->regs.mask = GPIO_INT;
+ ct->chip.irq_mask = irq_gc_mask_clr_bit;
+ ct->chip.irq_unmask = irq_gc_mask_set_bit;
+ ct->chip.irq_eoi = irq_gc_eoi;
+ ct->chip.irq_set_type = sdv_gpio_pub_set_type;
+
+ irq_setup_generic_chip(sd->gc, IRQ_MSK(SDV_NUM_PUB_GPIOS),
+ IRQ_GC_INIT_MASK_CACHE, IRQ_NOREQUEST,
+ IRQ_LEVEL | IRQ_NOPROBE);
+
+ irq_domain_add(&sd->id);
+ return 0;
+out_free_irq:
+ free_irq(pdev->irq, sd);
+out_free_desc:
+ irq_free_descs(sd->irq_base, SDV_NUM_PUB_GPIOS);
+ return ret;
+}
+
+static int __devinit sdv_gpio_probe(struct pci_dev *pdev,
+ const struct pci_device_id *pci_id)
+{
+ struct sdv_gpio_chip_data *sd;
+ unsigned long addr;
+ const void *prop;
+ int len;
+ int ret;
+ u32 mux_val;
+
+ sd = kzalloc(sizeof(struct sdv_gpio_chip_data), GFP_KERNEL);
+ if (!sd)
+ return -ENOMEM;
+ ret = pci_enable_device(pdev);
+ if (ret) {
+ dev_err(&pdev->dev, "can't enable device.\n");
+ goto done;
+ }
+
+ ret = pci_request_region(pdev, GPIO_BAR, DRV_NAME);
+ if (ret) {
+ dev_err(&pdev->dev, "can't alloc PCI BAR #%d\n", GPIO_BAR);
+ goto disable_pci;
+ }
+
+ addr = pci_resource_start(pdev, GPIO_BAR);
+ if (!addr)
+ goto release_reg;
+ sd->gpio_pub_base = ioremap(addr, pci_resource_len(pdev, GPIO_BAR));
+
+ prop = of_get_property(pdev->dev.of_node, "intel,muxctl", &len);
+ if (prop && len == 4) {
+ mux_val = of_read_number(prop, 1);
+ writel(mux_val, sd->gpio_pub_base + GPMUXCTL);
+ }
+
+ ret = bgpio_init(&sd->bgpio, &pdev->dev, 4,
+ sd->gpio_pub_base + GPINR, sd->gpio_pub_base + GPOUTR,
+ NULL, sd->gpio_pub_base + GPOER, NULL, false);
+ if (ret)
+ goto unmap;
+ sd->bgpio.gc.ngpio = SDV_NUM_PUB_GPIOS;
+
+ ret = gpiochip_add(&sd->bgpio.gc);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "gpiochip_add() failed.\n");
+ goto unmap;
+ }
+
+ ret = sdv_register_irqsupport(sd, pdev);
+ if (ret)
+ goto unmap;
+
+ pci_set_drvdata(pdev, sd);
+ dev_info(&pdev->dev, "Sodaville GPIO driver registered.\n");
+ return 0;
+
+unmap:
+ iounmap(sd->gpio_pub_base);
+release_reg:
+ pci_release_region(pdev, GPIO_BAR);
+disable_pci:
+ pci_disable_device(pdev);
+done:
+ kfree(sd);
+ return ret;
+}
+
+static void sdv_gpio_remove(struct pci_dev *pdev)
+{
+ struct sdv_gpio_chip_data *sd = pci_get_drvdata(pdev);
+
+ irq_domain_del(&sd->id);
+ free_irq(pdev->irq, sd);
+ irq_free_descs(sd->irq_base, SDV_NUM_PUB_GPIOS);
+
+ if (gpiochip_remove(&sd->bgpio.gc))
+ dev_err(&pdev->dev, "gpiochip_remove() failed.\n");
+
+ pci_release_region(pdev, GPIO_BAR);
+ iounmap(sd->gpio_pub_base);
+ pci_disable_device(pdev);
+ kfree(sd);
+}
+
+static struct pci_device_id sdv_gpio_pci_ids[] __devinitdata = {
+ { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_SDV_GPIO) },
+ { 0, },
+};
+
+static struct pci_driver sdv_gpio_driver = {
+ .name = DRV_NAME,
+ .id_table = sdv_gpio_pci_ids,
+ .probe = sdv_gpio_probe,
+ .remove = sdv_gpio_remove,
+};
+
+static int __init sdv_gpio_init(void)
+{
+ return pci_register_driver(&sdv_gpio_driver);
+}
+module_init(sdv_gpio_init);
+
+static void __exit sdv_gpio_exit(void)
+{
+ pci_unregister_driver(&sdv_gpio_driver);
+}
+module_exit(sdv_gpio_exit);
+
+MODULE_AUTHOR("Hans J. Koch <hjk@linutronix.de>");
+MODULE_DESCRIPTION("GPIO interface for Intel Sodaville SoCs");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/gpio/gpio-tps65910.c b/drivers/gpio/gpio-tps65910.c
index 91f45b9..7eef648 100644
--- a/drivers/gpio/gpio-tps65910.c
+++ b/drivers/gpio/gpio-tps65910.c
@@ -69,6 +69,7 @@
void tps65910_gpio_init(struct tps65910 *tps65910, int gpio_base)
{
int ret;
+ struct tps65910_board *board_data;
if (!gpio_base)
return;
@@ -80,10 +81,10 @@
switch(tps65910_chip_id(tps65910)) {
case TPS65910:
- tps65910->gpio.ngpio = 6;
+ tps65910->gpio.ngpio = TPS65910_NUM_GPIO;
break;
case TPS65911:
- tps65910->gpio.ngpio = 9;
+ tps65910->gpio.ngpio = TPS65911_NUM_GPIO;
break;
default:
return;
@@ -95,6 +96,21 @@
tps65910->gpio.set = tps65910_gpio_set;
tps65910->gpio.get = tps65910_gpio_get;
+ /* Configure sleep control for gpios */
+ board_data = dev_get_platdata(tps65910->dev);
+ if (board_data) {
+ int i;
+ for (i = 0; i < tps65910->gpio.ngpio; ++i) {
+ if (board_data->en_gpio_sleep[i]) {
+ ret = tps65910_set_bits(tps65910,
+ TPS65910_GPIO0 + i, GPIO_SLEEP_MASK);
+ if (ret < 0)
+ dev_warn(tps65910->dev,
+ "GPIO Sleep setting failed\n");
+ }
+ }
+ }
+
ret = gpiochip_add(&tps65910->gpio);
if (ret)
diff --git a/drivers/gpio/gpiolib.c b/drivers/gpio/gpiolib.c
index 17fdf4b..d773540 100644
--- a/drivers/gpio/gpiolib.c
+++ b/drivers/gpio/gpiolib.c
@@ -873,6 +873,7 @@
{
struct gpio_desc *desc;
int status = 0;
+ struct device *dev = NULL;
if (!gpio_is_valid(gpio)) {
status = -EINVAL;
@@ -884,19 +885,20 @@
desc = &gpio_desc[gpio];
if (test_bit(FLAG_EXPORT, &desc->flags)) {
- struct device *dev = NULL;
dev = class_find_device(&gpio_class, NULL, desc, match_export);
if (dev) {
gpio_setup_irq(desc, dev, 0);
clear_bit(FLAG_EXPORT, &desc->flags);
- put_device(dev);
- device_unregister(dev);
} else
status = -ENODEV;
}
mutex_unlock(&sysfs_lock);
+ if (dev) {
+ device_unregister(dev);
+ put_device(dev);
+ }
done:
if (status)
pr_debug("%s: gpio%d status %d\n", __func__, gpio, status);
diff --git a/drivers/of/gpio.c b/drivers/of/gpio.c
index 7e62d15..e034b38 100644
--- a/drivers/of/gpio.c
+++ b/drivers/of/gpio.c
@@ -78,8 +78,9 @@
EXPORT_SYMBOL(of_get_named_gpio_flags);
/**
- * of_gpio_count - Count GPIOs for a device
+ * of_gpio_named_count - Count GPIOs for a device
* @np: device node to count GPIOs for
+ * @propname: property name containing gpio specifier(s)
*
* The function returns the count of GPIOs specified for a node.
*
@@ -93,14 +94,14 @@
* defines four GPIOs (so this function will return 4), two of which
* are not specified.
*/
-unsigned int of_gpio_count(struct device_node *np)
+unsigned int of_gpio_named_count(struct device_node *np, const char* propname)
{
unsigned int cnt = 0;
do {
int ret;
- ret = of_parse_phandle_with_args(np, "gpios", "#gpio-cells",
+ ret = of_parse_phandle_with_args(np, propname, "#gpio-cells",
cnt, NULL);
/* A hole in the gpios = <> counts anyway. */
if (ret < 0 && ret != -EEXIST)
@@ -109,7 +110,7 @@
return cnt;
}
-EXPORT_SYMBOL(of_gpio_count);
+EXPORT_SYMBOL(of_gpio_named_count);
/**
* of_gpio_simple_xlate - translate gpio_spec to the GPIO number and flags
diff --git a/include/linux/mfd/tps65910.h b/include/linux/mfd/tps65910.h
index d0cb12e..9071902 100644
--- a/include/linux/mfd/tps65910.h
+++ b/include/linux/mfd/tps65910.h
@@ -657,6 +657,8 @@
/*Register GPIO (0x80) register.RegisterDescription */
+#define GPIO_SLEEP_MASK 0x80
+#define GPIO_SLEEP_SHIFT 7
#define GPIO_DEB_MASK 0x10
#define GPIO_DEB_SHIFT 4
#define GPIO_PUEN_MASK 0x08
@@ -740,6 +742,11 @@
#define TPS65910_GPIO_STS BIT(1)
#define TPS65910_GPIO_SET BIT(0)
+/* Max number of TPS65910/11 GPIOs */
+#define TPS65910_NUM_GPIO 6
+#define TPS65911_NUM_GPIO 9
+#define TPS6591X_MAX_NUM_GPIO 9
+
/* Regulator Index Definitions */
#define TPS65910_REG_VRTC 0
#define TPS65910_REG_VIO 1
@@ -779,6 +786,7 @@
int irq_base;
int vmbch_threshold;
int vmbch2_threshold;
+ bool en_gpio_sleep[TPS6591X_MAX_NUM_GPIO];
struct regulator_init_data *tps65910_pmic_init_data[TPS65910_NUM_REGS];
};
diff --git a/include/linux/of_gpio.h b/include/linux/of_gpio.h
index b254052..81733d1 100644
--- a/include/linux/of_gpio.h
+++ b/include/linux/of_gpio.h
@@ -50,7 +50,8 @@
extern int of_get_named_gpio_flags(struct device_node *np,
const char *list_name, int index, enum of_gpio_flags *flags);
-extern unsigned int of_gpio_count(struct device_node *np);
+extern unsigned int of_gpio_named_count(struct device_node *np,
+ const char* propname);
extern int of_mm_gpiochip_add(struct device_node *np,
struct of_mm_gpio_chip *mm_gc);
@@ -71,7 +72,8 @@
return -ENOSYS;
}
-static inline unsigned int of_gpio_count(struct device_node *np)
+static inline unsigned int of_gpio_named_count(struct device_node *np,
+ const char* propname)
{
return 0;
}
@@ -89,6 +91,27 @@
#endif /* CONFIG_OF_GPIO */
/**
+ * of_gpio_count - Count GPIOs for a device
+ * @np: device node to count GPIOs for
+ *
+ * The function returns the count of GPIOs specified for a node.
+ *
+ * Note that the empty GPIO specifiers counts too. For example,
+ *
+ * gpios = <0
+ * &pio1 1 2
+ * 0
+ * &pio2 3 4>;
+ *
+ * defines four GPIOs (so this function will return 4), two of which
+ * are not specified.
+ */
+static inline unsigned int of_gpio_count(struct device_node *np)
+{
+ return of_gpio_named_count(np, "gpios");
+}
+
+/**
* of_get_gpio_flags() - Get a GPIO number and flags to use with GPIO API
* @np: device node to get GPIO from
* @index: index of the GPIO