diff --git a/Documentation/ABI/testing/sysfs-bus-pci b/Documentation/ABI/testing/sysfs-bus-pci
index 34f5110..dff1f48 100644
--- a/Documentation/ABI/testing/sysfs-bus-pci
+++ b/Documentation/ABI/testing/sysfs-bus-pci
@@ -210,3 +210,15 @@
 		firmware assigned instance number of the PCI
 		device that can help in understanding the firmware
 		intended order of the PCI device.
+
+What:		/sys/bus/pci/devices/.../d3cold_allowed
+Date:		July 2012
+Contact:	Huang Ying <ying.huang@intel.com>
+Description:
+		d3cold_allowed is bit to control whether the corresponding PCI
+		device can be put into D3Cold state.  If it is cleared, the
+		device will never be put into D3Cold state.  If it is set, the
+		device may be put into D3Cold state if other requirements are
+		satisfied too.  Reading this attribute will show the current
+		value of d3cold_allowed bit.  Writing this attribute will set
+		the value of d3cold_allowed bit.
diff --git a/Documentation/ABI/testing/sysfs-tty b/Documentation/ABI/testing/sysfs-tty
index b138b66..0c43015 100644
--- a/Documentation/ABI/testing/sysfs-tty
+++ b/Documentation/ABI/testing/sysfs-tty
@@ -17,3 +17,12 @@
 		 device, like 'tty1'.
 		 The file supports poll() to detect virtual
 		 console switches.
+
+What:		/sys/class/tty/ttyS0/uartclk
+Date:		Sep 2012
+Contact:	Tomas Hlavacek <tmshlvck@gmail.com>
+Description:
+		 Shows the current uartclk value associated with the
+		 UART port in serial_core, that is bound to TTY like ttyS0.
+		 uartclk = 16 * baud_base
+
diff --git a/Documentation/block/00-INDEX b/Documentation/block/00-INDEX
index d111e3b..d18ecd8 100644
--- a/Documentation/block/00-INDEX
+++ b/Documentation/block/00-INDEX
@@ -3,15 +3,21 @@
 biodoc.txt
 	- Notes on the Generic Block Layer Rewrite in Linux 2.5
 capability.txt
-	- Generic Block Device Capability (/sys/block/<disk>/capability)
+	- Generic Block Device Capability (/sys/block/<device>/capability)
+cfq-iosched.txt
+	- CFQ IO scheduler tunables
+data-integrity.txt
+	- Block data integrity
 deadline-iosched.txt
 	- Deadline IO scheduler tunables
 ioprio.txt
 	- Block io priorities (in CFQ scheduler)
+queue-sysfs.txt
+	- Queue's sysfs entries
 request.txt
 	- The members of struct request (in include/linux/blkdev.h)
 stat.txt
-	- Block layer statistics in /sys/block/<dev>/stat
+	- Block layer statistics in /sys/block/<device>/stat
 switching-sched.txt
 	- Switching I/O schedulers at runtime
 writeback_cache_control.txt
diff --git a/Documentation/block/cfq-iosched.txt b/Documentation/block/cfq-iosched.txt
index 6d670f5..d89b4fe 100644
--- a/Documentation/block/cfq-iosched.txt
+++ b/Documentation/block/cfq-iosched.txt
@@ -1,3 +1,14 @@
+CFQ (Complete Fairness Queueing)
+===============================
+
+The main aim of CFQ scheduler is to provide a fair allocation of the disk
+I/O bandwidth for all the processes which requests an I/O operation.
+
+CFQ maintains the per process queue for the processes which request I/O
+operation(syncronous requests). In case of asynchronous requests, all the
+requests from all the processes are batched together according to their
+process's I/O priority.
+
 CFQ ioscheduler tunables
 ========================
 
@@ -25,6 +36,72 @@
 controller or for storage arrays), setting slice_idle=0 might end up in better
 throughput and acceptable latencies.
 
+back_seek_max
+-------------
+This specifies, given in Kbytes, the maximum "distance" for backward seeking.
+The distance is the amount of space from the current head location to the
+sectors that are backward in terms of distance.
+
+This parameter allows the scheduler to anticipate requests in the "backward"
+direction and consider them as being the "next" if they are within this
+distance from the current head location.
+
+back_seek_penalty
+-----------------
+This parameter is used to compute the cost of backward seeking. If the
+backward distance of request is just 1/back_seek_penalty from a "front"
+request, then the seeking cost of two requests is considered equivalent.
+
+So scheduler will not bias toward one or the other request (otherwise scheduler
+will bias toward front request). Default value of back_seek_penalty is 2.
+
+fifo_expire_async
+-----------------
+This parameter is used to set the timeout of asynchronous requests. Default
+value of this is 248ms.
+
+fifo_expire_sync
+----------------
+This parameter is used to set the timeout of synchronous requests. Default
+value of this is 124ms. In case to favor synchronous requests over asynchronous
+one, this value should be decreased relative to fifo_expire_async.
+
+slice_async
+-----------
+This parameter is same as of slice_sync but for asynchronous queue. The
+default value is 40ms.
+
+slice_async_rq
+--------------
+This parameter is used to limit the dispatching of asynchronous request to
+device request queue in queue's slice time. The maximum number of request that
+are allowed to be dispatched also depends upon the io priority. Default value
+for this is 2.
+
+slice_sync
+----------
+When a queue is selected for execution, the queues IO requests are only
+executed for a certain amount of time(time_slice) before switching to another
+queue. This parameter is used to calculate the time slice of synchronous
+queue.
+
+time_slice is computed using the below equation:-
+time_slice = slice_sync + (slice_sync/5 * (4 - prio)). To increase the
+time_slice of synchronous queue, increase the value of slice_sync. Default
+value is 100ms.
+
+quantum
+-------
+This specifies the number of request dispatched to the device queue. In a
+queue's time slice, a request will not be dispatched if the number of request
+in the device exceeds this parameter. This parameter is used for synchronous
+request.
+
+In case of storage with several disk, this setting can limit the parallel
+processing of request. Therefore, increasing the value can imporve the
+performace although this can cause the latency of some I/O to increase due
+to more number of requests.
+
 CFQ IOPS Mode for group scheduling
 ===================================
 Basic CFQ design is to provide priority based time slices. Higher priority
diff --git a/Documentation/block/queue-sysfs.txt b/Documentation/block/queue-sysfs.txt
index 6518a55..e54ac1d 100644
--- a/Documentation/block/queue-sysfs.txt
+++ b/Documentation/block/queue-sysfs.txt
@@ -9,20 +9,71 @@
 Files denoted with a RO postfix are readonly and the RW postfix means
 read-write.
 
+add_random (RW)
+----------------
+This file allows to trun off the disk entropy contribution. Default
+value of this file is '1'(on).
+
+discard_granularity (RO)
+-----------------------
+This shows the size of internal allocation of the device in bytes, if
+reported by the device. A value of '0' means device does not support
+the discard functionality.
+
+discard_max_bytes (RO)
+----------------------
+Devices that support discard functionality may have internal limits on
+the number of bytes that can be trimmed or unmapped in a single operation.
+The discard_max_bytes parameter is set by the device driver to the maximum
+number of bytes that can be discarded in a single operation. Discard
+requests issued to the device must not exceed this limit. A discard_max_bytes
+value of 0 means that the device does not support discard functionality.
+
+discard_zeroes_data (RO)
+------------------------
+When read, this file will show if the discarded block are zeroed by the
+device or not. If its value is '1' the blocks are zeroed otherwise not.
+
 hw_sector_size (RO)
 -------------------
 This is the hardware sector size of the device, in bytes.
 
+iostats (RW)
+-------------
+This file is used to control (on/off) the iostats accounting of the
+disk.
+
+logical_block_size (RO)
+-----------------------
+This is the logcal block size of the device, in bytes.
+
 max_hw_sectors_kb (RO)
 ----------------------
 This is the maximum number of kilobytes supported in a single data transfer.
 
+max_integrity_segments (RO)
+---------------------------
+When read, this file shows the max limit of integrity segments as
+set by block layer which a hardware controller can handle.
+
 max_sectors_kb (RW)
 -------------------
 This is the maximum number of kilobytes that the block layer will allow
 for a filesystem request. Must be smaller than or equal to the maximum
 size allowed by the hardware.
 
+max_segments (RO)
+-----------------
+Maximum number of segments of the device.
+
+max_segment_size (RO)
+---------------------
+Maximum segment size of the device.
+
+minimum_io_size (RO)
+--------------------
+This is the smallest preferred io size reported by the device.
+
 nomerges (RW)
 -------------
 This enables the user to disable the lookup logic involved with IO
@@ -45,11 +96,24 @@
 each request queue may have upto N request pools, each independently
 regulated by nr_requests.
 
+optimal_io_size (RO)
+--------------------
+This is the optimal io size reported by the device.
+
+physical_block_size (RO)
+------------------------
+This is the physical block size of device, in bytes.
+
 read_ahead_kb (RW)
 ------------------
 Maximum number of kilobytes to read-ahead for filesystems on this block
 device.
 
+rotational (RW)
+---------------
+This file is used to stat if the device is of rotational type or
+non-rotational type.
+
 rq_affinity (RW)
 ----------------
 If this option is '1', the block layer will migrate request completions to the
diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
index 70cd49b..1dd6225 100644
--- a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
+++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
@@ -10,8 +10,8 @@
 - compatible : Should be "fsl,<chip>-esdhc"
 
 Optional properties:
-- fsl,cd-internal : Indicate to use controller internal card detection
-- fsl,wp-internal : Indicate to use controller internal write protection
+- fsl,cd-controller : Indicate to use controller internal card detection
+- fsl,wp-controller : Indicate to use controller internal write protection
 
 Examples:
 
@@ -19,8 +19,8 @@
 	compatible = "fsl,imx51-esdhc";
 	reg = <0x70004000 0x4000>;
 	interrupts = <1>;
-	fsl,cd-internal;
-	fsl,wp-internal;
+	fsl,cd-controller;
+	fsl,wp-controller;
 };
 
 esdhc@70008000 {
diff --git a/Documentation/devicetree/bindings/tty/serial/nxp-lpc32xx-hsuart.txt b/Documentation/devicetree/bindings/tty/serial/nxp-lpc32xx-hsuart.txt
new file mode 100644
index 0000000..0d439df
--- /dev/null
+++ b/Documentation/devicetree/bindings/tty/serial/nxp-lpc32xx-hsuart.txt
@@ -0,0 +1,14 @@
+* NXP LPC32xx SoC High Speed UART
+
+Required properties:
+- compatible: Should be "nxp,lpc3220-hsuart"
+- reg: Should contain registers location and length
+- interrupts: Should contain interrupt
+
+Example:
+
+	uart1: serial@40014000 {
+		compatible = "nxp,lpc3220-hsuart";
+		reg = <0x40014000 0x1000>;
+		interrupts = <26 0>;
+	};
diff --git a/Documentation/devicetree/bindings/tty/serial/of-serial.txt b/Documentation/devicetree/bindings/tty/serial/of-serial.txt
index 0847fde..ba385f2 100644
--- a/Documentation/devicetree/bindings/tty/serial/of-serial.txt
+++ b/Documentation/devicetree/bindings/tty/serial/of-serial.txt
@@ -25,6 +25,8 @@
   accesses to the UART (e.g. TI davinci).
 - used-by-rtas : set to indicate that the port is in use by the OpenFirmware
   RTAS and should not be registered.
+- no-loopback-test: set to indicate that the port does not implements loopback
+  test mode
 
 Example:
 
diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt
index afaff31..f4d8c71 100644
--- a/Documentation/feature-removal-schedule.txt
+++ b/Documentation/feature-removal-schedule.txt
@@ -579,7 +579,7 @@
 ----------------------------
 
 What:	at91-mci driver ("CONFIG_MMC_AT91")
-When:	3.7
+When:	3.8
 Why:	There are two mci drivers: at91-mci and atmel-mci. The PDC support
 	was added to atmel-mci as a first step to support more chips.
 	Then at91-mci was kept only for old IP versions (on at91rm9200 and
diff --git a/Documentation/serial/00-INDEX b/Documentation/serial/00-INDEX
index e09468a..f7b0c7d 100644
--- a/Documentation/serial/00-INDEX
+++ b/Documentation/serial/00-INDEX
@@ -2,8 +2,6 @@
 	- this file.
 README.cycladesZ
 	- info on Cyclades-Z firmware loading.
-computone.txt
-	- info on Computone Intelliport II/Plus Multiport Serial Driver.
 digiepca.txt
 	- info on Digi Intl. {PC,PCI,EISA}Xx and Xem series cards.
 hayes-esp.txt
diff --git a/Documentation/serial/computone.txt b/Documentation/serial/computone.txt
deleted file mode 100644
index a6a1158..0000000
--- a/Documentation/serial/computone.txt
+++ /dev/null
@@ -1,520 +0,0 @@
-NOTE: This is an unmaintained driver.  It is not guaranteed to work due to
-changes made in the tty layer in 2.6.  If you wish to take over maintenance of
-this driver, contact Michael Warfield <mhw@wittsend.com>.
-
-Changelog:
-----------
-11-01-2001:	Original Document
-
-10-29-2004:	Minor misspelling & format fix, update status of driver.
-		James Nelson <james4765@gmail.com>
-
-Computone Intelliport II/Plus Multiport Serial Driver
------------------------------------------------------
-
-Release Notes For Linux Kernel 2.2 and higher.
-These notes are for the drivers which have already been integrated into the
-kernel and have been tested on Linux kernels 2.0, 2.2, 2.3, and 2.4.
-
-Version: 1.2.14
-Date: 11/01/2001
-Historical Author: Andrew Manison <amanison@america.net>
-Primary Author: Doug McNash
-
-This file assumes that you are using the Computone drivers which are
-integrated into the kernel sources.  For updating the drivers or installing
-drivers into kernels which do not already have Computone drivers, please
-refer to the instructions in the README.computone file in the driver patch.
-
-
-1. INTRODUCTION
-
-This driver supports the entire family of Intelliport II/Plus controllers
-with the exception of the MicroChannel controllers.  It does not support
-products previous to the Intelliport II.
-
-This driver was developed on the v2.0.x Linux tree and has been tested up
-to v2.4.14; it will probably not work with earlier v1.X kernels,.
-
-
-2. QUICK INSTALLATION
-
-Hardware - If you have an ISA card, find a free interrupt and io port. 
-		   List those in use with `cat /proc/interrupts` and 
-		   `cat /proc/ioports`.  Set the card dip switches to a free 
-		   address.  You may need to configure your BIOS to reserve an
-		   irq for an ISA card.  PCI and EISA parameters are set
-		   automagically.  Insert card into computer with the power off 
-		   before or after drivers installation.
-
-	Note the hardware address from the Computone ISA cards installed into
-		the system.  These are required for editing ip2.c or editing
-		/etc/modprobe.d/*.conf, or for specification on the modprobe
-		command line.
-
-	Note that the /etc/modules.conf should be used for older (pre-2.6)
-		kernels.
-
-Software -
-
-Module installation:
-
-a) Determine free irq/address to use if any (configure BIOS if need be)
-b) Run "make config" or "make menuconfig" or "make xconfig"
-   Select (m) module for CONFIG_COMPUTONE under character
-   devices.  CONFIG_PCI and CONFIG_MODULES also may need to be set.
-c) Set address on ISA cards then:
-   edit /usr/src/linux/drivers/char/ip2.c if needed 
-	or
-   edit config file in  /etc/modprobe.d/ if needed (module).
-	or both to match this setting.
-d) Run "make modules"
-e) Run "make modules_install"
-f) Run "/sbin/depmod -a"
-g) install driver using `modprobe ip2 <options>` (options listed below)
-h) run ip2mkdev (either the script below or the binary version)
-
-
-Kernel installation:
-
-a) Determine free irq/address to use if any (configure BIOS if need be)
-b) Run "make config" or "make menuconfig" or "make xconfig"
-   Select (y) kernel for CONFIG_COMPUTONE under character
-   devices.  CONFIG_PCI may need to be set if you have PCI bus.
-c) Set address on ISA cards then:
-	   edit /usr/src/linux/drivers/char/ip2.c  
-           (Optional - may be specified on kernel command line now)
-d) Run "make zImage" or whatever target you prefer.
-e) mv /usr/src/linux/arch/x86/boot/zImage to /boot.
-f) Add new config for this kernel into /etc/lilo.conf, run "lilo"
-	or copy to a floppy disk and boot from that floppy disk.
-g) Reboot using this kernel
-h) run ip2mkdev (either the script below or the binary version)
-
-Kernel command line options:
-
-When compiling the driver into the kernel, io and irq may be
-compiled into the driver by editing ip2.c and setting the values for
-io and irq in the appropriate array.  An alternative is to specify
-a command line parameter to the kernel at boot up.
-
-        ip2=io0,irq0,io1,irq1,io2,irq2,io3,irq3
-
-Note that this order is very different from the specifications for the
-modload parameters which have separate IRQ and IO specifiers.
-
-The io port also selects PCI (1) and EISA (2) boards.
-
-        io=0    No board
-        io=1    PCI board
-        io=2    EISA board
-        else    ISA board io address
-
-You only need to specify the boards which are present.
-
-        Examples:
-
-                2 PCI boards:
-
-                        ip2=1,0,1,0
-
-                1 ISA board at 0x310 irq 5:
-
-                        ip2=0x310,5
-
-This can be added to and "append" option in lilo.conf similar to this:
-
-        append="ip2=1,0,1,0"
-
-
-3. INSTALLATION
-
-Previously, the driver sources were packaged with a set of patch files
-to update the character drivers' makefile and configuration file, and other 
-kernel source files. A build script (ip2build) was included which applies 
-the patches if needed, and build any utilities needed.
-What you receive may be a single patch file in conventional kernel
-patch format build script. That form can also be applied by
-running patch -p1 < ThePatchFile.  Otherwise run ip2build.
- 
-The driver can be installed as a module (recommended) or built into the 
-kernel. This is selected as for other drivers through the `make config`
-command from the root of the Linux source tree. If the driver is built 
-into the kernel you will need to edit the file ip2.c to match the boards 
-you are installing. See that file for instructions. If the driver is 
-installed as a module the configuration can also be specified on the
-modprobe command line as follows:
-
-	modprobe ip2 irq=irq1,irq2,irq3,irq4 io=addr1,addr2,addr3,addr4
-
-where irqnum is one of the valid Intelliport II interrupts (3,4,5,7,10,11,
-12,15) and addr1-4 are the base addresses for up to four controllers. If 
-the irqs are not specified the driver uses the default in ip2.c (which 
-selects polled mode). If no base addresses are specified the defaults in 
-ip2.c are used. If you are autoloading the driver module with kerneld or
-kmod the base addresses and interrupt number must also be set in ip2.c
-and recompile or just insert and options line in /etc/modprobe.d/*.conf or both.
-The options line is equivalent to the command line and takes precedence over
-what is in ip2.c. 
-
-config sample to put /etc/modprobe.d/*.conf:
-	options ip2 io=1,0x328 irq=1,10
-	alias char-major-71 ip2
-	alias char-major-72 ip2
-	alias char-major-73 ip2
-
-The equivalent in ip2.c:
-
-static int io[IP2_MAX_BOARDS]= { 1, 0x328, 0, 0 };
-static int irq[IP2_MAX_BOARDS] = { 1, 10, -1, -1 }; 
-
-The equivalent for the kernel command line (in lilo.conf):
-
-        append="ip2=1,1,0x328,10"
-
-
-Note:	Both io and irq should be updated to reflect YOUR system.  An "io"
-	address of 1 or 2 indicates a PCI or EISA card in the board table.
-	The PCI or EISA irq will be assigned automatically.
-
-Specifying an invalid or in-use irq will default the driver into
-running in polled mode for that card.  If all irq entries are 0 then
-all cards will operate in polled mode.
-
-If you select the driver as part of the kernel run :
-
-	make zlilo (or whatever you do to create a bootable kernel)
-
-If you selected a module run :
-
-	make modules && make modules_install
-
-The utility ip2mkdev (see 5 and 7 below) creates all the device nodes
-required by the driver.  For a device to be created it must be configured
-in the driver and the board must be installed. Only devices corresponding
-to real IntelliPort II ports are created. With multiple boards and expansion
-boxes this will leave gaps in the sequence of device names. ip2mkdev uses
-Linux tty naming conventions: ttyF0 - ttyF255 for normal devices, and
-cuf0 - cuf255 for callout devices.
-
-
-4. USING THE DRIVERS
-
-As noted above, the driver implements the ports in accordance with Linux
-conventions, and the devices should be interchangeable with the standard
-serial devices. (This is a key point for problem reporting: please make
-sure that what you are trying do works on the ttySx/cuax ports first; then 
-tell us what went wrong with the ip2 ports!)
-
-Higher speeds can be obtained using the setserial utility which remaps 
-38,400 bps (extb) to 57,600 bps, 115,200 bps, or a custom speed. 
-Intelliport II installations using the PowerPort expansion module can
-use the custom speed setting to select the highest speeds: 153,600 bps,
-230,400 bps, 307,200 bps, 460,800bps and 921,600 bps. The base for
-custom baud rate configuration is fixed at 921,600 for cards/expansion
-modules with ST654's and 115200 for those with Cirrus CD1400's.  This
-corresponds to the maximum bit rates those chips are capable.  
-For example if the baud base is 921600 and the baud divisor is 18 then
-the custom rate is 921600/18 = 51200 bps.  See the setserial man page for
-complete details. Of course if stty accepts the higher rates now you can
-use that as well as the standard ioctls().
-
-
-5. ip2mkdev and assorted utilities...
-
-Several utilities, including the source for a binary ip2mkdev utility are
-available under .../drivers/char/ip2.  These can be build by changing to
-that directory and typing "make" after the kernel has be built.  If you do
-not wish to compile the binary utilities, the shell script below can be
-cut out and run as "ip2mkdev" to create the necessary device files.  To
-use the ip2mkdev script, you must have procfs enabled and the proc file
-system mounted on /proc.
-
-
-6. NOTES
-
-This is a release version of the driver, but it is impossible to test it
-in all configurations of Linux. If there is any anomalous behaviour that 
-does not match the standard serial port's behaviour please let us know.
-
-
-7. ip2mkdev shell script
-
-Previously, this script was simply attached here.  It is now attached as a
-shar archive to make it easier to extract the script from the documentation.
-To create the ip2mkdev shell script change to a convenient directory (/tmp
-works just fine) and run the following command:
-
-	unshar Documentation/serial/computone.txt
-		(This file)
-
-You should now have a file ip2mkdev in your current working directory with
-permissions set to execute.  Running that script with then create the
-necessary devices for the Computone boards, interfaces, and ports which
-are present on you system at the time it is run.
-
-
-#!/bin/sh
-# This is a shell archive (produced by GNU sharutils 4.2.1).
-# To extract the files from this archive, save it to some FILE, remove
-# everything before the `!/bin/sh' line above, then type `sh FILE'.
-#
-# Made on 2001-10-29 10:32 EST by <mhw@alcove.wittsend.com>.
-# Source directory was `/home2/src/tmp'.
-#
-# Existing files will *not* be overwritten unless `-c' is specified.
-#
-# This shar contains:
-# length mode       name
-# ------ ---------- ------------------------------------------
-#   4251 -rwxr-xr-x ip2mkdev
-#
-save_IFS="${IFS}"
-IFS="${IFS}:"
-gettext_dir=FAILED
-locale_dir=FAILED
-first_param="$1"
-for dir in $PATH
-do
-  if test "$gettext_dir" = FAILED && test -f $dir/gettext \
-     && ($dir/gettext --version >/dev/null 2>&1)
-  then
-    set `$dir/gettext --version 2>&1`
-    if test "$3" = GNU
-    then
-      gettext_dir=$dir
-    fi
-  fi
-  if test "$locale_dir" = FAILED && test -f $dir/shar \
-     && ($dir/shar --print-text-domain-dir >/dev/null 2>&1)
-  then
-    locale_dir=`$dir/shar --print-text-domain-dir`
-  fi
-done
-IFS="$save_IFS"
-if test "$locale_dir" = FAILED || test "$gettext_dir" = FAILED
-then
-  echo=echo
-else
-  TEXTDOMAINDIR=$locale_dir
-  export TEXTDOMAINDIR
-  TEXTDOMAIN=sharutils
-  export TEXTDOMAIN
-  echo="$gettext_dir/gettext -s"
-fi
-if touch -am -t 200112312359.59 $$.touch >/dev/null 2>&1 && test ! -f 200112312359.59 -a -f $$.touch; then
-  shar_touch='touch -am -t $1$2$3$4$5$6.$7 "$8"'
-elif touch -am 123123592001.59 $$.touch >/dev/null 2>&1 && test ! -f 123123592001.59 -a ! -f 123123592001.5 -a -f $$.touch; then
-  shar_touch='touch -am $3$4$5$6$1$2.$7 "$8"'
-elif touch -am 1231235901 $$.touch >/dev/null 2>&1 && test ! -f 1231235901 -a -f $$.touch; then
-  shar_touch='touch -am $3$4$5$6$2 "$8"'
-else
-  shar_touch=:
-  echo
-  $echo 'WARNING: not restoring timestamps.  Consider getting and'
-  $echo "installing GNU \`touch', distributed in GNU File Utilities..."
-  echo
-fi
-rm -f 200112312359.59 123123592001.59 123123592001.5 1231235901 $$.touch
-#
-if mkdir _sh17581; then
-  $echo 'x -' 'creating lock directory'
-else
-  $echo 'failed to create lock directory'
-  exit 1
-fi
-# ============= ip2mkdev ==============
-if test -f 'ip2mkdev' && test "$first_param" != -c; then
-  $echo 'x -' SKIPPING 'ip2mkdev' '(file already exists)'
-else
-  $echo 'x -' extracting 'ip2mkdev' '(text)'
-  sed 's/^X//' << 'SHAR_EOF' > 'ip2mkdev' &&
-#!/bin/sh -
-#
-#	ip2mkdev
-#
-#	Make or remove devices as needed for Computone Intelliport drivers
-#
-#	First rule!  If the dev file exists and you need it, don't mess
-#	with it.  That prevents us from screwing up open ttys, ownership
-#	and permissions on a running system!
-#
-#	This script will NOT remove devices that no longer exist if their
-#	board or interface box has been removed.  If you want to get rid
-#	of them, you can manually do an "rm -f /dev/ttyF* /dev/cuaf*"
-#	before running this script.  Running this script will then recreate
-#	all the valid devices.
-#
-#	Michael H. Warfield
-#	/\/\|=mhw=|\/\/
-#	mhw@wittsend.com
-#
-#	Updated 10/29/2000 for version 1.2.13 naming convention
-#		under devfs.	/\/\|=mhw=|\/\/
-#
-#	Updated 03/09/2000 for devfs support in ip2 drivers. /\/\|=mhw=|\/\/
-#
-X
-if test -d /dev/ip2 ; then
-#	This is devfs mode...  We don't do anything except create symlinks
-#	from the real devices to the old names!
-X	cd /dev
-X	echo "Creating symbolic links to devfs devices"
-X	for i in `ls ip2` ; do
-X		if test ! -L ip2$i ; then
-X			# Remove it incase it wasn't a symlink (old device)
-X			rm -f ip2$i
-X			ln -s ip2/$i ip2$i
-X		fi
-X	done
-X	for i in `( cd tts ; ls F* )` ; do
-X		if test ! -L tty$i ; then
-X			# Remove it incase it wasn't a symlink (old device)
-X			rm -f tty$i
-X			ln -s tts/$i tty$i
-X		fi
-X	done
-X	for i in `( cd cua ; ls F* )` ; do
-X		DEVNUMBER=`expr $i : 'F\(.*\)'`
-X		if test ! -L cuf$DEVNUMBER ; then
-X			# Remove it incase it wasn't a symlink (old device)
-X			rm -f cuf$DEVNUMBER
-X			ln -s cua/$i cuf$DEVNUMBER
-X		fi
-X	done
-X	exit 0
-fi
-X
-if test ! -f /proc/tty/drivers
-then
-X	echo "\
-Unable to check driver status.
-Make sure proc file system is mounted."
-X
-X	exit 255
-fi
-X
-if test ! -f /proc/tty/driver/ip2
-then
-X	echo "\
-Unable to locate ip2 proc file.
-Attempting to load driver"
-X
-X	if /sbin/insmod ip2
-X	then
-X		if test ! -f /proc/tty/driver/ip2
-X		then
-X			echo "\
-Unable to locate ip2 proc file after loading driver.
-Driver initialization failure or driver version error.
-"
-X		exit 255
-X		fi
-X	else
-X		echo "Unable to load ip2 driver."
-X		exit 255
-X	fi
-fi
-X
-# Ok...  So we got the driver loaded and we can locate the procfs files.
-# Next we need our major numbers.
-X
-TTYMAJOR=`sed -e '/^ip2/!d' -e '/\/dev\/tt/!d' -e 's/.*tt[^ 	]*[ 	]*\([0-9]*\)[ 	]*.*/\1/' < /proc/tty/drivers`
-CUAMAJOR=`sed -e '/^ip2/!d' -e '/\/dev\/cu/!d' -e 's/.*cu[^ 	]*[ 	]*\([0-9]*\)[ 	]*.*/\1/' < /proc/tty/drivers`
-BRDMAJOR=`sed -e '/^Driver: /!d' -e 's/.*IMajor=\([0-9]*\)[ 	]*.*/\1/' < /proc/tty/driver/ip2`
-X
-echo "\
-TTYMAJOR = $TTYMAJOR
-CUAMAJOR = $CUAMAJOR
-BRDMAJOR = $BRDMAJOR
-"
-X
-# Ok...  Now we should know our major numbers, if appropriate...
-# Now we need our boards and start the device loops.
-X
-grep '^Board [0-9]:' /proc/tty/driver/ip2 | while read token number type alltherest
-do
-X	# The test for blank "type" will catch the stats lead-in lines
-X	# if they exist in the file
-X	if test "$type" = "vacant" -o "$type" = "Vacant" -o "$type" = ""
-X	then
-X		continue
-X	fi
-X
-X	BOARDNO=`expr "$number" : '\([0-9]\):'`
-X	PORTS=`expr "$alltherest" : '.*ports=\([0-9]*\)' | tr ',' ' '`
-X	MINORS=`expr "$alltherest" : '.*minors=\([0-9,]*\)' | tr ',' ' '`
-X
-X	if test "$BOARDNO" = "" -o "$PORTS" = ""
-X	then
-#	This may be a bug.  We should at least get this much information
-X		echo "Unable to process board line"
-X		continue
-X	fi
-X
-X	if test "$MINORS" = ""
-X	then
-#	Silently skip this one.  This board seems to have no boxes
-X		continue
-X	fi
-X
-X	echo "board $BOARDNO: $type ports = $PORTS; port numbers = $MINORS"
-X
-X	if test "$BRDMAJOR" != ""
-X	then
-X		BRDMINOR=`expr $BOARDNO \* 4`
-X		STSMINOR=`expr $BRDMINOR + 1`
-X		if test ! -c /dev/ip2ipl$BOARDNO ; then
-X			mknod /dev/ip2ipl$BOARDNO c $BRDMAJOR $BRDMINOR
-X		fi
-X		if test ! -c /dev/ip2stat$BOARDNO ; then
-X			mknod /dev/ip2stat$BOARDNO c $BRDMAJOR $STSMINOR
-X		fi
-X	fi
-X
-X	if test "$TTYMAJOR" != ""
-X	then
-X		PORTNO=$BOARDBASE
-X
-X		for PORTNO in $MINORS
-X		do
-X			if test ! -c /dev/ttyF$PORTNO ; then
-X				# We got the hardware but no device - make it
-X				mknod /dev/ttyF$PORTNO c $TTYMAJOR $PORTNO
-X			fi	
-X		done
-X	fi
-X
-X	if test "$CUAMAJOR" != ""
-X	then
-X		PORTNO=$BOARDBASE
-X
-X		for PORTNO in $MINORS
-X		do
-X			if test ! -c /dev/cuf$PORTNO ; then
-X				# We got the hardware but no device - make it
-X				mknod /dev/cuf$PORTNO c $CUAMAJOR $PORTNO
-X			fi	
-X		done
-X	fi
-done
-X
-Xexit 0
-SHAR_EOF
-  (set 20 01 10 29 10 32 01 'ip2mkdev'; eval "$shar_touch") &&
-  chmod 0755 'ip2mkdev' ||
-  $echo 'restore of' 'ip2mkdev' 'failed'
-  if ( md5sum --help 2>&1 | grep 'sage: md5sum \[' ) >/dev/null 2>&1 \
-  && ( md5sum --version 2>&1 | grep -v 'textutils 1.12' ) >/dev/null; then
-    md5sum -c << SHAR_EOF >/dev/null 2>&1 \
-    || $echo 'ip2mkdev:' 'MD5 check failed'
-cb5717134509f38bad9fde6b1f79b4a4  ip2mkdev
-SHAR_EOF
-  else
-    shar_count="`LC_ALL= LC_CTYPE= LANG= wc -c < 'ip2mkdev'`"
-    test 4251 -eq "$shar_count" ||
-    $echo 'ip2mkdev:' 'original size' '4251,' 'current size' "$shar_count!"
-  fi
-fi
-rm -fr _sh17581
-exit 0
diff --git a/Documentation/watchdog/src/watchdog-test.c b/Documentation/watchdog/src/watchdog-test.c
index 73ff5cc..3da8229 100644
--- a/Documentation/watchdog/src/watchdog-test.c
+++ b/Documentation/watchdog/src/watchdog-test.c
@@ -31,7 +31,7 @@
  * or "-e" to enable the card.
  */
 
-void term(int sig)
+static void term(int sig)
 {
     close(fd);
     fprintf(stderr, "Stopping watchdog ticks...\n");
diff --git a/Makefile b/Makefile
index 3540268..0f66f14 100644
--- a/Makefile
+++ b/Makefile
@@ -1,7 +1,7 @@
 VERSION = 3
 PATCHLEVEL = 6
 SUBLEVEL = 0
-EXTRAVERSION = -rc3
+EXTRAVERSION = -rc5
 NAME = Saber-toothed Squirrel
 
 # *DOCUMENTATION*
diff --git a/arch/alpha/kernel/srmcons.c b/arch/alpha/kernel/srmcons.c
index 3ea8094..5d58652 100644
--- a/arch/alpha/kernel/srmcons.c
+++ b/arch/alpha/kernel/srmcons.c
@@ -223,6 +223,7 @@
 		driver->subtype = SYSTEM_TYPE_SYSCONS;
 		driver->init_termios = tty_std_termios;
 		tty_set_operations(driver, &srmcons_ops);
+		tty_port_link_device(&srmcons_singleton.port, driver, 0);
 		err = tty_register_driver(driver);
 		if (err) {
 			put_tty_driver(driver);
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 6d6e18f..2f88d8d 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -6,7 +6,7 @@
 	select HAVE_DMA_API_DEBUG
 	select HAVE_IDE if PCI || ISA || PCMCIA
 	select HAVE_DMA_ATTRS
-	select HAVE_DMA_CONTIGUOUS if (CPU_V6 || CPU_V6K || CPU_V7)
+	select HAVE_DMA_CONTIGUOUS if MMU
 	select HAVE_MEMBLOCK
 	select RTC_LIB
 	select SYS_SUPPORTS_APM_EMULATION
@@ -2144,6 +2144,7 @@
 config CPU_FREQ_IMX
 	tristate "CPUfreq driver for i.MX CPUs"
 	depends on ARCH_MXC && CPU_FREQ
+	select CPU_FREQ_TABLE
 	help
 	  This enables the CPUfreq driver for i.MX CPUs.
 
diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
index 59509c4..bd0cff3 100644
--- a/arch/arm/boot/dts/am33xx.dtsi
+++ b/arch/arm/boot/dts/am33xx.dtsi
@@ -154,5 +154,10 @@
 			#size-cells = <0>;
 			ti,hwmods = "i2c3";
 		};
+
+		wdt2: wdt@44e35000 {
+			compatible = "ti,omap3-wdt";
+			ti,hwmods = "wd_timer2";
+		};
 	};
 };
diff --git a/arch/arm/boot/dts/at91sam9g25ek.dts b/arch/arm/boot/dts/at91sam9g25ek.dts
index 7829a4d..96514c1 100644
--- a/arch/arm/boot/dts/at91sam9g25ek.dts
+++ b/arch/arm/boot/dts/at91sam9g25ek.dts
@@ -15,7 +15,7 @@
 	compatible = "atmel,at91sam9g25ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
 
 	chosen {
-		bootargs = "128M console=ttyS0,115200 root=/dev/mtdblock1 rw rootfstype=ubifs ubi.mtd=1 root=ubi0:rootfs";
+		bootargs = "console=ttyS0,115200 root=/dev/mtdblock1 rw rootfstype=ubifs ubi.mtd=1 root=ubi0:rootfs";
 	};
 
 	ahb {
diff --git a/arch/arm/boot/dts/imx51-babbage.dts b/arch/arm/boot/dts/imx51-babbage.dts
index cd86177..59d9789 100644
--- a/arch/arm/boot/dts/imx51-babbage.dts
+++ b/arch/arm/boot/dts/imx51-babbage.dts
@@ -25,8 +25,8 @@
 		aips@70000000 { /* aips-1 */
 			spba@70000000 {
 				esdhc@70004000 { /* ESDHC1 */
-					fsl,cd-internal;
-					fsl,wp-internal;
+					fsl,cd-controller;
+					fsl,wp-controller;
 					status = "okay";
 				};
 
diff --git a/arch/arm/boot/dts/kirkwood-iconnect.dts b/arch/arm/boot/dts/kirkwood-iconnect.dts
index 52d9470..f8ca6fa 100644
--- a/arch/arm/boot/dts/kirkwood-iconnect.dts
+++ b/arch/arm/boot/dts/kirkwood-iconnect.dts
@@ -41,9 +41,13 @@
 		};
 		power-blue {
 			label = "power:blue";
-			gpios = <&gpio1 11 0>;
+			gpios = <&gpio1 10 0>;
 			linux,default-trigger = "timer";
 		};
+		power-red {
+			label = "power:red";
+			gpios = <&gpio1 11 0>;
+		};
 		usb1 {
 			label = "usb1:blue";
 			gpios = <&gpio1 12 0>;
diff --git a/arch/arm/boot/dts/twl6030.dtsi b/arch/arm/boot/dts/twl6030.dtsi
index 3b2f351..d351b27 100644
--- a/arch/arm/boot/dts/twl6030.dtsi
+++ b/arch/arm/boot/dts/twl6030.dtsi
@@ -66,6 +66,7 @@
 
 	vcxio: regulator@8 {
 		compatible = "ti,twl6030-vcxio";
+		regulator-always-on;
 	};
 
 	vusb: regulator@9 {
@@ -74,10 +75,12 @@
 
 	v1v8: regulator@10 {
 		compatible = "ti,twl6030-v1v8";
+		regulator-always-on;
 	};
 
 	v2v1: regulator@11 {
 		compatible = "ti,twl6030-v2v1";
+		regulator-always-on;
 	};
 
 	clk32kg: regulator@12 {
diff --git a/arch/arm/configs/armadillo800eva_defconfig b/arch/arm/configs/armadillo800eva_defconfig
index 7d87184..90610c7 100644
--- a/arch/arm/configs/armadillo800eva_defconfig
+++ b/arch/arm/configs/armadillo800eva_defconfig
@@ -33,7 +33,7 @@
 CONFIG_FORCE_MAX_ZONEORDER=13
 CONFIG_ZBOOT_ROM_TEXT=0x0
 CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="console=tty0 console=ttySC1,115200 earlyprintk=sh-sci.1,115200 ignore_loglevel root=/dev/nfs ip=dhcp nfsroot=,rsize=4096,wsize=4096"
+CONFIG_CMDLINE="console=tty0 console=ttySC1,115200 earlyprintk=sh-sci.1,115200 ignore_loglevel root=/dev/nfs ip=dhcp nfsroot=,rsize=4096,wsize=4096 rw"
 CONFIG_CMDLINE_FORCE=y
 CONFIG_KEXEC=y
 CONFIG_VFP=y
diff --git a/arch/arm/configs/u8500_defconfig b/arch/arm/configs/u8500_defconfig
index 2d4f661..da68454 100644
--- a/arch/arm/configs/u8500_defconfig
+++ b/arch/arm/configs/u8500_defconfig
@@ -86,6 +86,7 @@
 CONFIG_LEDS_CLASS=y
 CONFIG_LEDS_LM3530=y
 CONFIG_LEDS_LP5521=y
+CONFIG_LEDS_GPIO=y
 CONFIG_RTC_CLASS=y
 CONFIG_RTC_DRV_AB8500=y
 CONFIG_RTC_DRV_PL031=y
diff --git a/arch/arm/include/asm/dma-mapping.h b/arch/arm/include/asm/dma-mapping.h
index 2ae842d..5c44dcb 100644
--- a/arch/arm/include/asm/dma-mapping.h
+++ b/arch/arm/include/asm/dma-mapping.h
@@ -203,6 +203,13 @@
 }
 
 /*
+ * This can be called during early boot to increase the size of the atomic
+ * coherent DMA pool above the default value of 256KiB. It must be called
+ * before postcore_initcall.
+ */
+extern void __init init_dma_coherent_pool_size(unsigned long size);
+
+/*
  * This can be called during boot to increase the size of the consistent
  * DMA region above it's default value of 2MB. It must be called before the
  * memory allocator is initialised, i.e. before any core_initcall.
diff --git a/arch/arm/mach-at91/at91rm9200_time.c b/arch/arm/mach-at91/at91rm9200_time.c
index 104ca40..aaa443b 100644
--- a/arch/arm/mach-at91/at91rm9200_time.c
+++ b/arch/arm/mach-at91/at91rm9200_time.c
@@ -197,7 +197,7 @@
 	at91_st_read(AT91_ST_SR);
 
 	/* Make IRQs happen for the system timer */
-	setup_irq(AT91_ID_SYS, &at91rm9200_timer_irq);
+	setup_irq(NR_IRQS_LEGACY + AT91_ID_SYS, &at91rm9200_timer_irq);
 
 	/* The 32KiHz "Slow Clock" (tick every 30517.58 nanoseconds) is used
 	 * directly for the clocksource and all clockevents, after adjusting
diff --git a/arch/arm/mach-at91/at91sam9260_devices.c b/arch/arm/mach-at91/at91sam9260_devices.c
index 7b9c2ba..bce572a 100644
--- a/arch/arm/mach-at91/at91sam9260_devices.c
+++ b/arch/arm/mach-at91/at91sam9260_devices.c
@@ -726,6 +726,8 @@
 		.flags	= IORESOURCE_MEM,
 	}, {
 		.flags	= IORESOURCE_MEM,
+	}, {
+		.flags  = IORESOURCE_IRQ,
 	},
 };
 
@@ -744,10 +746,12 @@
 	 * The second resource is needed:
 	 * GPBR will serve as the storage for RTC time offset
 	 */
-	at91sam9260_rtt_device.num_resources = 2;
+	at91sam9260_rtt_device.num_resources = 3;
 	rtt_resources[1].start = AT91SAM9260_BASE_GPBR +
 				 4 * CONFIG_RTC_DRV_AT91SAM9_GPBR;
 	rtt_resources[1].end = rtt_resources[1].start + 3;
+	rtt_resources[2].start = NR_IRQS_LEGACY + AT91_ID_SYS;
+	rtt_resources[2].end = NR_IRQS_LEGACY + AT91_ID_SYS;
 }
 #else
 static void __init at91_add_device_rtt_rtc(void)
diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c
index 8df5c1bd..bc2590d 100644
--- a/arch/arm/mach-at91/at91sam9261_devices.c
+++ b/arch/arm/mach-at91/at91sam9261_devices.c
@@ -609,6 +609,8 @@
 		.flags	= IORESOURCE_MEM,
 	}, {
 		.flags	= IORESOURCE_MEM,
+	}, {
+		.flags  = IORESOURCE_IRQ,
 	}
 };
 
@@ -626,10 +628,12 @@
 	 * The second resource is needed:
 	 * GPBR will serve as the storage for RTC time offset
 	 */
-	at91sam9261_rtt_device.num_resources = 2;
+	at91sam9261_rtt_device.num_resources = 3;
 	rtt_resources[1].start = AT91SAM9261_BASE_GPBR +
 				 4 * CONFIG_RTC_DRV_AT91SAM9_GPBR;
 	rtt_resources[1].end = rtt_resources[1].start + 3;
+	rtt_resources[2].start = NR_IRQS_LEGACY + AT91_ID_SYS;
+	rtt_resources[2].end = NR_IRQS_LEGACY + AT91_ID_SYS;
 }
 #else
 static void __init at91_add_device_rtt_rtc(void)
diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c
index eb6bbf8..9b6ca73 100644
--- a/arch/arm/mach-at91/at91sam9263_devices.c
+++ b/arch/arm/mach-at91/at91sam9263_devices.c
@@ -990,6 +990,8 @@
 		.flags	= IORESOURCE_MEM,
 	}, {
 		.flags	= IORESOURCE_MEM,
+	}, {
+		.flags  = IORESOURCE_IRQ,
 	}
 };
 
@@ -1006,6 +1008,8 @@
 		.flags	= IORESOURCE_MEM,
 	}, {
 		.flags	= IORESOURCE_MEM,
+	}, {
+		.flags  = IORESOURCE_IRQ,
 	}
 };
 
@@ -1027,14 +1031,14 @@
 		 * The second resource is needed only for the chosen RTT:
 		 * GPBR will serve as the storage for RTC time offset
 		 */
-		at91sam9263_rtt0_device.num_resources = 2;
+		at91sam9263_rtt0_device.num_resources = 3;
 		at91sam9263_rtt1_device.num_resources = 1;
 		pdev = &at91sam9263_rtt0_device;
 		r = rtt0_resources;
 		break;
 	case 1:
 		at91sam9263_rtt0_device.num_resources = 1;
-		at91sam9263_rtt1_device.num_resources = 2;
+		at91sam9263_rtt1_device.num_resources = 3;
 		pdev = &at91sam9263_rtt1_device;
 		r = rtt1_resources;
 		break;
@@ -1047,6 +1051,8 @@
 	pdev->name = "rtc-at91sam9";
 	r[1].start = AT91SAM9263_BASE_GPBR + 4 * CONFIG_RTC_DRV_AT91SAM9_GPBR;
 	r[1].end = r[1].start + 3;
+	r[2].start = NR_IRQS_LEGACY + AT91_ID_SYS;
+	r[2].end = NR_IRQS_LEGACY + AT91_ID_SYS;
 }
 #else
 static void __init at91_add_device_rtt_rtc(void)
diff --git a/arch/arm/mach-at91/at91sam9g45_devices.c b/arch/arm/mach-at91/at91sam9g45_devices.c
index 0607399..1b47319 100644
--- a/arch/arm/mach-at91/at91sam9g45_devices.c
+++ b/arch/arm/mach-at91/at91sam9g45_devices.c
@@ -1293,6 +1293,8 @@
 		.flags	= IORESOURCE_MEM,
 	}, {
 		.flags	= IORESOURCE_MEM,
+	}, {
+		.flags  = IORESOURCE_IRQ,
 	}
 };
 
@@ -1310,10 +1312,12 @@
 	 * The second resource is needed:
 	 * GPBR will serve as the storage for RTC time offset
 	 */
-	at91sam9g45_rtt_device.num_resources = 2;
+	at91sam9g45_rtt_device.num_resources = 3;
 	rtt_resources[1].start = AT91SAM9G45_BASE_GPBR +
 				 4 * CONFIG_RTC_DRV_AT91SAM9_GPBR;
 	rtt_resources[1].end = rtt_resources[1].start + 3;
+	rtt_resources[2].start = NR_IRQS_LEGACY + AT91_ID_SYS;
+	rtt_resources[2].end = NR_IRQS_LEGACY + AT91_ID_SYS;
 }
 #else
 static void __init at91_add_device_rtt_rtc(void)
diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c
index f09fff9..b3d365d 100644
--- a/arch/arm/mach-at91/at91sam9rl_devices.c
+++ b/arch/arm/mach-at91/at91sam9rl_devices.c
@@ -688,6 +688,8 @@
 		.flags	= IORESOURCE_MEM,
 	}, {
 		.flags	= IORESOURCE_MEM,
+	}, {
+		.flags  = IORESOURCE_IRQ,
 	}
 };
 
@@ -705,10 +707,12 @@
 	 * The second resource is needed:
 	 * GPBR will serve as the storage for RTC time offset
 	 */
-	at91sam9rl_rtt_device.num_resources = 2;
+	at91sam9rl_rtt_device.num_resources = 3;
 	rtt_resources[1].start = AT91SAM9RL_BASE_GPBR +
 				 4 * CONFIG_RTC_DRV_AT91SAM9_GPBR;
 	rtt_resources[1].end = rtt_resources[1].start + 3;
+	rtt_resources[2].start = NR_IRQS_LEGACY + AT91_ID_SYS;
+	rtt_resources[2].end = NR_IRQS_LEGACY + AT91_ID_SYS;
 }
 #else
 static void __init at91_add_device_rtt_rtc(void)
diff --git a/arch/arm/mach-at91/clock.c b/arch/arm/mach-at91/clock.c
index de2ec6b..188c829 100644
--- a/arch/arm/mach-at91/clock.c
+++ b/arch/arm/mach-at91/clock.c
@@ -63,6 +63,12 @@
 
 #define cpu_has_300M_plla()	(cpu_is_at91sam9g10())
 
+#define cpu_has_240M_plla()	(cpu_is_at91sam9261() \
+				|| cpu_is_at91sam9263() \
+				|| cpu_is_at91sam9rl())
+
+#define cpu_has_210M_plla()	(cpu_is_at91sam9260())
+
 #define cpu_has_pllb()		(!(cpu_is_at91sam9rl() \
 				|| cpu_is_at91sam9g45() \
 				|| cpu_is_at91sam9x5() \
@@ -706,6 +712,12 @@
 	} else if (cpu_has_800M_plla()) {
 		if (plla.rate_hz > 800000000)
 			pll_overclock = true;
+	} else if (cpu_has_240M_plla()) {
+		if (plla.rate_hz > 240000000)
+			pll_overclock = true;
+	} else if (cpu_has_210M_plla()) {
+		if (plla.rate_hz > 210000000)
+			pll_overclock = true;
 	} else {
 		if (plla.rate_hz > 209000000)
 			pll_overclock = true;
diff --git a/arch/arm/mach-dove/common.c b/arch/arm/mach-dove/common.c
index 4db5de5..6321567 100644
--- a/arch/arm/mach-dove/common.c
+++ b/arch/arm/mach-dove/common.c
@@ -102,7 +102,8 @@
 void __init dove_ge00_init(struct mv643xx_eth_platform_data *eth_data)
 {
 	orion_ge00_init(eth_data, DOVE_GE00_PHYS_BASE,
-			IRQ_DOVE_GE00_SUM, IRQ_DOVE_GE00_ERR);
+			IRQ_DOVE_GE00_SUM, IRQ_DOVE_GE00_ERR,
+			1600);
 }
 
 /*****************************************************************************
diff --git a/arch/arm/mach-exynos/mach-origen.c b/arch/arm/mach-exynos/mach-origen.c
index 5ca8030..4e574c2 100644
--- a/arch/arm/mach-exynos/mach-origen.c
+++ b/arch/arm/mach-exynos/mach-origen.c
@@ -42,6 +42,7 @@
 #include <plat/backlight.h>
 #include <plat/fb.h>
 #include <plat/mfc.h>
+#include <plat/hdmi.h>
 
 #include <mach/ohci.h>
 #include <mach/map.h>
@@ -734,6 +735,11 @@
 	s3c_gpio_setpull(EXYNOS4_GPX2(2), S3C_GPIO_PULL_NONE);
 }
 
+/* I2C module and id for HDMIPHY */
+static struct i2c_board_info hdmiphy_info = {
+	I2C_BOARD_INFO("hdmiphy-exynos4210", 0x38),
+};
+
 static void s5p_tv_setup(void)
 {
 	/* Direct HPD to HDMI chip */
@@ -781,6 +787,7 @@
 
 	s5p_tv_setup();
 	s5p_i2c_hdmiphy_set_platdata(NULL);
+	s5p_hdmi_set_platdata(&hdmiphy_info, NULL, 0);
 
 #ifdef CONFIG_DRM_EXYNOS
 	s5p_device_fimd0.dev.platform_data = &drm_fimd_pdata;
diff --git a/arch/arm/mach-exynos/mach-smdkv310.c b/arch/arm/mach-exynos/mach-smdkv310.c
index 3cfa688..73f2bce 100644
--- a/arch/arm/mach-exynos/mach-smdkv310.c
+++ b/arch/arm/mach-exynos/mach-smdkv310.c
@@ -40,6 +40,7 @@
 #include <plat/mfc.h>
 #include <plat/ehci.h>
 #include <plat/clock.h>
+#include <plat/hdmi.h>
 
 #include <mach/map.h>
 #include <mach/ohci.h>
@@ -354,6 +355,11 @@
 	.pwm_period_ns  = 1000,
 };
 
+/* I2C module and id for HDMIPHY */
+static struct i2c_board_info hdmiphy_info = {
+	I2C_BOARD_INFO("hdmiphy-exynos4210", 0x38),
+};
+
 static void s5p_tv_setup(void)
 {
 	/* direct HPD to HDMI chip */
@@ -388,6 +394,7 @@
 
 	s5p_tv_setup();
 	s5p_i2c_hdmiphy_set_platdata(NULL);
+	s5p_hdmi_set_platdata(&hdmiphy_info, NULL, 0);
 
 	samsung_keypad_set_platdata(&smdkv310_keypad_data);
 
diff --git a/arch/arm/mach-gemini/irq.c b/arch/arm/mach-gemini/irq.c
index ca70e5f..020852d 100644
--- a/arch/arm/mach-gemini/irq.c
+++ b/arch/arm/mach-gemini/irq.c
@@ -17,6 +17,7 @@
 #include <linux/sched.h>
 #include <asm/irq.h>
 #include <asm/mach/irq.h>
+#include <asm/system_misc.h>
 #include <mach/hardware.h>
 
 #define IRQ_SOURCE(base_addr)	(base_addr + 0x00)
diff --git a/arch/arm/mach-imx/Makefile b/arch/arm/mach-imx/Makefile
index 07f7c22..d004d37 100644
--- a/arch/arm/mach-imx/Makefile
+++ b/arch/arm/mach-imx/Makefile
@@ -9,7 +9,8 @@
 obj-$(CONFIG_SOC_IMX31) += mm-imx3.o cpu-imx31.o clk-imx31.o iomux-imx31.o ehci-imx31.o pm-imx3.o
 obj-$(CONFIG_SOC_IMX35) += mm-imx3.o cpu-imx35.o clk-imx35.o ehci-imx35.o pm-imx3.o
 
-obj-$(CONFIG_SOC_IMX5) += cpu-imx5.o mm-imx5.o clk-imx51-imx53.o ehci-imx5.o pm-imx5.o cpu_op-mx51.o
+imx5-pm-$(CONFIG_PM) += pm-imx5.o
+obj-$(CONFIG_SOC_IMX5) += cpu-imx5.o mm-imx5.o clk-imx51-imx53.o ehci-imx5.o $(imx5-pm-y) cpu_op-mx51.o
 
 obj-$(CONFIG_COMMON_CLK) += clk-pllv1.o clk-pllv2.o clk-pllv3.o clk-gate2.o \
 			    clk-pfd.o clk-busy.o
@@ -70,14 +71,13 @@
 obj-$(CONFIG_HAVE_IMX_GPC) += gpc.o
 obj-$(CONFIG_HAVE_IMX_MMDC) += mmdc.o
 obj-$(CONFIG_HAVE_IMX_SRC) += src.o
-obj-$(CONFIG_CPU_V7) += head-v7.o
-AFLAGS_head-v7.o :=-Wa,-march=armv7-a
-obj-$(CONFIG_SMP) += platsmp.o
+AFLAGS_headsmp.o :=-Wa,-march=armv7-a
+obj-$(CONFIG_SMP) += headsmp.o platsmp.o
 obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o
 obj-$(CONFIG_SOC_IMX6Q) += clk-imx6q.o mach-imx6q.o
 
 ifeq ($(CONFIG_PM),y)
-obj-$(CONFIG_SOC_IMX6Q) += pm-imx6q.o
+obj-$(CONFIG_SOC_IMX6Q) += pm-imx6q.o headsmp.o
 endif
 
 # i.MX5 based machines
diff --git a/arch/arm/mach-imx/clk-imx6q.c b/arch/arm/mach-imx/clk-imx6q.c
index ea89520..4233d9e 100644
--- a/arch/arm/mach-imx/clk-imx6q.c
+++ b/arch/arm/mach-imx/clk-imx6q.c
@@ -152,7 +152,7 @@
 	ssi2, ssi3, uart_ipg, uart_serial, usboh3, usdhc1, usdhc2, usdhc3,
 	usdhc4, vdo_axi, vpu_axi, cko1, pll1_sys, pll2_bus, pll3_usb_otg,
 	pll4_audio, pll5_video, pll6_mlb, pll7_usb_host, pll8_enet, ssi1_ipg,
-	ssi2_ipg, ssi3_ipg, rom, usbphy1, usbphy2,
+	ssi2_ipg, ssi3_ipg, rom, usbphy1, usbphy2, ldb_di0_div_3_5, ldb_di1_div_3_5,
 	clk_max
 };
 
@@ -288,8 +288,10 @@
 	clk[gpu3d_shader]     = imx_clk_divider("gpu3d_shader",     "gpu3d_shader_sel",  base + 0x18, 29, 3);
 	clk[ipu1_podf]        = imx_clk_divider("ipu1_podf",        "ipu1_sel",          base + 0x3c, 11, 3);
 	clk[ipu2_podf]        = imx_clk_divider("ipu2_podf",        "ipu2_sel",          base + 0x3c, 16, 3);
-	clk[ldb_di0_podf]     = imx_clk_divider("ldb_di0_podf",     "ldb_di0_sel",       base + 0x20, 10, 1);
-	clk[ldb_di1_podf]     = imx_clk_divider("ldb_di1_podf",     "ldb_di1_sel",       base + 0x20, 11, 1);
+	clk[ldb_di0_div_3_5]  = imx_clk_fixed_factor("ldb_di0_div_3_5", "ldb_di0_sel", 2, 7);
+	clk[ldb_di0_podf]     = imx_clk_divider("ldb_di0_podf",     "ldb_di0_div_3_5",       base + 0x20, 10, 1);
+	clk[ldb_di1_div_3_5]  = imx_clk_fixed_factor("ldb_di1_div_3_5", "ldb_di1_sel", 2, 7);
+	clk[ldb_di1_podf]     = imx_clk_divider("ldb_di1_podf",     "ldb_di1_div_3_5",   base + 0x20, 11, 1);
 	clk[ipu1_di0_pre]     = imx_clk_divider("ipu1_di0_pre",     "ipu1_di0_pre_sel",  base + 0x34, 3,  3);
 	clk[ipu1_di1_pre]     = imx_clk_divider("ipu1_di1_pre",     "ipu1_di1_pre_sel",  base + 0x34, 12, 3);
 	clk[ipu2_di0_pre]     = imx_clk_divider("ipu2_di0_pre",     "ipu2_di0_pre_sel",  base + 0x38, 3,  3);
diff --git a/arch/arm/mach-imx/head-v7.S b/arch/arm/mach-imx/headsmp.S
similarity index 100%
rename from arch/arm/mach-imx/head-v7.S
rename to arch/arm/mach-imx/headsmp.S
diff --git a/arch/arm/mach-imx/hotplug.c b/arch/arm/mach-imx/hotplug.c
index 20ed2d5..f8f7437 100644
--- a/arch/arm/mach-imx/hotplug.c
+++ b/arch/arm/mach-imx/hotplug.c
@@ -42,22 +42,6 @@
 	  : "cc");
 }
 
-static inline void cpu_leave_lowpower(void)
-{
-	unsigned int v;
-
-	asm volatile(
-		"mrc	p15, 0, %0, c1, c0, 0\n"
-	"	orr	%0, %0, %1\n"
-	"	mcr	p15, 0, %0, c1, c0, 0\n"
-	"	mrc	p15, 0, %0, c1, c0, 1\n"
-	"	orr	%0, %0, %2\n"
-	"	mcr	p15, 0, %0, c1, c0, 1\n"
-	  : "=&r" (v)
-	  : "Ir" (CR_C), "Ir" (0x40)
-	  : "cc");
-}
-
 /*
  * platform-specific code to shutdown a CPU
  *
@@ -67,11 +51,10 @@
 {
 	cpu_enter_lowpower();
 	imx_enable_cpu(cpu, false);
-	cpu_do_idle();
-	cpu_leave_lowpower();
 
-	/* We should never return from idle */
-	panic("cpu %d unexpectedly exit from shutdown\n", cpu);
+	/* spin here until hardware takes it down */
+	while (1)
+		;
 }
 
 int platform_cpu_disable(unsigned int cpu)
diff --git a/arch/arm/mach-imx/mach-imx6q.c b/arch/arm/mach-imx/mach-imx6q.c
index 5ec0608..045b3f6 100644
--- a/arch/arm/mach-imx/mach-imx6q.c
+++ b/arch/arm/mach-imx/mach-imx6q.c
@@ -71,7 +71,7 @@
 /* For imx6q sabrelite board: set KSZ9021RN RGMII pad skew */
 static int ksz9021rn_phy_fixup(struct phy_device *phydev)
 {
-	if (IS_ENABLED(CONFIG_PHYLIB)) {
+	if (IS_BUILTIN(CONFIG_PHYLIB)) {
 		/* min rx data delay */
 		phy_write(phydev, 0x0b, 0x8105);
 		phy_write(phydev, 0x0c, 0x0000);
@@ -112,7 +112,7 @@
 
 static void __init imx6q_sabrelite_init(void)
 {
-	if (IS_ENABLED(CONFIG_PHYLIB))
+	if (IS_BUILTIN(CONFIG_PHYLIB))
 		phy_register_fixup_for_uid(PHY_ID_KSZ9021, MICREL_PHY_ID_MASK,
 				ksz9021rn_phy_fixup);
 	imx6q_sabrelite_cko1_setup();
diff --git a/arch/arm/mach-kirkwood/Makefile.boot b/arch/arm/mach-kirkwood/Makefile.boot
index a571755..a13299d 100644
--- a/arch/arm/mach-kirkwood/Makefile.boot
+++ b/arch/arm/mach-kirkwood/Makefile.boot
@@ -7,7 +7,8 @@
 dtb-$(CONFIG_MACH_DLINK_KIRKWOOD_DT) += kirkwood-dns325.dtb
 dtb-$(CONFIG_MACH_ICONNECT_DT) += kirkwood-iconnect.dtb
 dtb-$(CONFIG_MACH_IB62X0_DT) += kirkwood-ib62x0.dtb
-dtb-$(CONFIG_MACH_TS219_DT)	+= kirkwood-qnap-ts219.dtb
+dtb-$(CONFIG_MACH_TS219_DT)	+= kirkwood-ts219-6281.dtb
+dtb-$(CONFIG_MACH_TS219_DT)	+= kirkwood-ts219-6282.dtb
 dtb-$(CONFIG_MACH_GOFLEXNET_DT) += kirkwood-goflexnet.dtb
 dtb-$(CONFIG_MACH_LSXL_DT) += kirkwood-lschlv2.dtb
 dtb-$(CONFIG_MACH_LSXL_DT) += kirkwood-lsxhl.dtb
diff --git a/arch/arm/mach-kirkwood/common.c b/arch/arm/mach-kirkwood/common.c
index c4b64ad..1201191 100644
--- a/arch/arm/mach-kirkwood/common.c
+++ b/arch/arm/mach-kirkwood/common.c
@@ -301,7 +301,7 @@
 {
 	orion_ge00_init(eth_data,
 			GE00_PHYS_BASE, IRQ_KIRKWOOD_GE00_SUM,
-			IRQ_KIRKWOOD_GE00_ERR);
+			IRQ_KIRKWOOD_GE00_ERR, 1600);
 	/* The interface forgets the MAC address assigned by u-boot if
 	the clock is turned off, so claim the clk now. */
 	clk_prepare_enable(ge0);
@@ -315,7 +315,7 @@
 {
 	orion_ge01_init(eth_data,
 			GE01_PHYS_BASE, IRQ_KIRKWOOD_GE01_SUM,
-			IRQ_KIRKWOOD_GE01_ERR);
+			IRQ_KIRKWOOD_GE01_ERR, 1600);
 	clk_prepare_enable(ge1);
 }
 
@@ -517,6 +517,13 @@
 void __init kirkwood_init_early(void)
 {
 	orion_time_set_base(TIMER_VIRT_BASE);
+
+	/*
+	 * Some Kirkwood devices allocate their coherent buffers from atomic
+	 * context. Increase size of atomic coherent pool to make sure such
+	 * the allocations won't fail.
+	 */
+	init_dma_coherent_pool_size(SZ_1M);
 }
 
 int kirkwood_tclk;
diff --git a/arch/arm/mach-kirkwood/db88f6281-bp-setup.c b/arch/arm/mach-kirkwood/db88f6281-bp-setup.c
index d933593..be90b7d 100644
--- a/arch/arm/mach-kirkwood/db88f6281-bp-setup.c
+++ b/arch/arm/mach-kirkwood/db88f6281-bp-setup.c
@@ -10,6 +10,7 @@
 
 #include <linux/kernel.h>
 #include <linux/init.h>
+#include <linux/sizes.h>
 #include <linux/platform_device.h>
 #include <linux/mtd/partitions.h>
 #include <linux/ata_platform.h>
diff --git a/arch/arm/mach-mmp/sram.c b/arch/arm/mach-mmp/sram.c
index 4304f95..7e8a5a2 100644
--- a/arch/arm/mach-mmp/sram.c
+++ b/arch/arm/mach-mmp/sram.c
@@ -68,7 +68,7 @@
 	struct resource *res;
 	int ret = 0;
 
-	if (!pdata && !pdata->pool_name)
+	if (!pdata || !pdata->pool_name)
 		return -ENODEV;
 
 	info = kzalloc(sizeof(*info), GFP_KERNEL);
diff --git a/arch/arm/mach-mv78xx0/addr-map.c b/arch/arm/mach-mv78xx0/addr-map.c
index 62b53d7..a9bc841 100644
--- a/arch/arm/mach-mv78xx0/addr-map.c
+++ b/arch/arm/mach-mv78xx0/addr-map.c
@@ -37,7 +37,7 @@
 #define WIN0_OFF(n)		(BRIDGE_VIRT_BASE + 0x0000 + ((n) << 4))
 #define WIN8_OFF(n)		(BRIDGE_VIRT_BASE + 0x0900 + (((n) - 8) << 4))
 
-static void __init __iomem *win_cfg_base(int win)
+static void __init __iomem *win_cfg_base(const struct orion_addr_map_cfg *cfg, int win)
 {
 	/*
 	 * Find the control register base address for this window.
diff --git a/arch/arm/mach-mv78xx0/common.c b/arch/arm/mach-mv78xx0/common.c
index b4c53b8..3057f7d 100644
--- a/arch/arm/mach-mv78xx0/common.c
+++ b/arch/arm/mach-mv78xx0/common.c
@@ -213,7 +213,8 @@
 {
 	orion_ge00_init(eth_data,
 			GE00_PHYS_BASE, IRQ_MV78XX0_GE00_SUM,
-			IRQ_MV78XX0_GE_ERR);
+			IRQ_MV78XX0_GE_ERR,
+			MV643XX_TX_CSUM_DEFAULT_LIMIT);
 }
 
 
@@ -224,7 +225,8 @@
 {
 	orion_ge01_init(eth_data,
 			GE01_PHYS_BASE, IRQ_MV78XX0_GE01_SUM,
-			NO_IRQ);
+			NO_IRQ,
+			MV643XX_TX_CSUM_DEFAULT_LIMIT);
 }
 
 
diff --git a/arch/arm/mach-omap1/board-ams-delta.c b/arch/arm/mach-omap1/board-ams-delta.c
index c534698..c162369 100644
--- a/arch/arm/mach-omap1/board-ams-delta.c
+++ b/arch/arm/mach-omap1/board-ams-delta.c
@@ -37,7 +37,6 @@
 #include <plat/board-ams-delta.h>
 #include <plat/keypad.h>
 #include <plat/mux.h>
-#include <plat/board.h>
 
 #include <mach/hardware.h>
 #include <mach/ams-delta-fiq.h>
diff --git a/arch/arm/mach-omap1/board-fsample.c b/arch/arm/mach-omap1/board-fsample.c
index 6872f3f..6d98552 100644
--- a/arch/arm/mach-omap1/board-fsample.c
+++ b/arch/arm/mach-omap1/board-fsample.c
@@ -32,7 +32,6 @@
 #include <plat/flash.h>
 #include <plat/fpga.h>
 #include <plat/keypad.h>
-#include <plat/board.h>
 
 #include <mach/hardware.h>
 
diff --git a/arch/arm/mach-omap1/board-generic.c b/arch/arm/mach-omap1/board-generic.c
index 6ec385e..04b5fda 100644
--- a/arch/arm/mach-omap1/board-generic.c
+++ b/arch/arm/mach-omap1/board-generic.c
@@ -23,7 +23,6 @@
 #include <asm/mach/map.h>
 
 #include <plat/mux.h>
-#include <plat/board.h>
 
 #include <mach/usb.h>
 
@@ -52,9 +51,6 @@
 };
 #endif
 
-static struct omap_board_config_kernel generic_config[] __initdata = {
-};
-
 static void __init omap_generic_init(void)
 {
 #ifdef CONFIG_ARCH_OMAP15XX
@@ -76,8 +72,6 @@
 	}
 #endif
 
-	omap_board_config = generic_config;
-	omap_board_config_size = ARRAY_SIZE(generic_config);
 	omap_serial_init();
 	omap_register_i2c_bus(1, 100, NULL, 0);
 }
diff --git a/arch/arm/mach-omap1/board-htcherald.c b/arch/arm/mach-omap1/board-htcherald.c
index b3f6e94..b9771b5 100644
--- a/arch/arm/mach-omap1/board-htcherald.c
+++ b/arch/arm/mach-omap1/board-htcherald.c
@@ -42,7 +42,6 @@
 #include <asm/mach/arch.h>
 
 #include <plat/omap7xx.h>
-#include <plat/board.h>
 #include <plat/keypad.h>
 #include <plat/mmc.h>
 
diff --git a/arch/arm/mach-omap1/board-nokia770.c b/arch/arm/mach-omap1/board-nokia770.c
index 2c0ca8f..ec01f03 100644
--- a/arch/arm/mach-omap1/board-nokia770.c
+++ b/arch/arm/mach-omap1/board-nokia770.c
@@ -26,7 +26,6 @@
 #include <asm/mach/map.h>
 
 #include <plat/mux.h>
-#include <plat/board.h>
 #include <plat/keypad.h>
 #include <plat/lcd_mipid.h>
 #include <plat/mmc.h>
diff --git a/arch/arm/mach-omap1/board-osk.c b/arch/arm/mach-omap1/board-osk.c
index 8784705..569b687 100644
--- a/arch/arm/mach-omap1/board-osk.c
+++ b/arch/arm/mach-omap1/board-osk.c
@@ -39,6 +39,7 @@
 #include <linux/mtd/partitions.h>
 #include <linux/mtd/physmap.h>
 #include <linux/i2c/tps65010.h>
+#include <linux/platform_data/omap1_bl.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
diff --git a/arch/arm/mach-omap1/board-palmte.c b/arch/arm/mach-omap1/board-palmte.c
index 26bcb9d..49f8d74 100644
--- a/arch/arm/mach-omap1/board-palmte.c
+++ b/arch/arm/mach-omap1/board-palmte.c
@@ -28,6 +28,7 @@
 #include <linux/interrupt.h>
 #include <linux/apm-emulation.h>
 #include <linux/omapfb.h>
+#include <linux/platform_data/omap1_bl.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -37,7 +38,6 @@
 #include <plat/mux.h>
 #include <plat/tc.h>
 #include <plat/dma.h>
-#include <plat/board.h>
 #include <plat/irda.h>
 #include <plat/keypad.h>
 
diff --git a/arch/arm/mach-omap1/board-palmtt.c b/arch/arm/mach-omap1/board-palmtt.c
index 4d09944..01523cd 100644
--- a/arch/arm/mach-omap1/board-palmtt.c
+++ b/arch/arm/mach-omap1/board-palmtt.c
@@ -27,6 +27,7 @@
 #include <linux/omapfb.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/ads7846.h>
+#include <linux/platform_data/omap1_bl.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -37,7 +38,6 @@
 #include <plat/mux.h>
 #include <plat/dma.h>
 #include <plat/tc.h>
-#include <plat/board.h>
 #include <plat/irda.h>
 #include <plat/keypad.h>
 
diff --git a/arch/arm/mach-omap1/board-palmz71.c b/arch/arm/mach-omap1/board-palmz71.c
index 3559803..a7abce6 100644
--- a/arch/arm/mach-omap1/board-palmz71.c
+++ b/arch/arm/mach-omap1/board-palmz71.c
@@ -30,6 +30,7 @@
 #include <linux/omapfb.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/ads7846.h>
+#include <linux/platform_data/omap1_bl.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -39,7 +40,6 @@
 #include <plat/mux.h>
 #include <plat/dma.h>
 #include <plat/tc.h>
-#include <plat/board.h>
 #include <plat/irda.h>
 #include <plat/keypad.h>
 
diff --git a/arch/arm/mach-omap1/board-perseus2.c b/arch/arm/mach-omap1/board-perseus2.c
index 703d55e..277e0bc 100644
--- a/arch/arm/mach-omap1/board-perseus2.c
+++ b/arch/arm/mach-omap1/board-perseus2.c
@@ -32,7 +32,6 @@
 #include <plat/fpga.h>
 #include <plat/flash.h>
 #include <plat/keypad.h>
-#include <plat/board.h>
 
 #include <mach/hardware.h>
 
diff --git a/arch/arm/mach-omap1/board-sx1.c b/arch/arm/mach-omap1/board-sx1.c
index 8c665bd..2e1fff2 100644
--- a/arch/arm/mach-omap1/board-sx1.c
+++ b/arch/arm/mach-omap1/board-sx1.c
@@ -38,7 +38,6 @@
 #include <plat/dma.h>
 #include <plat/irda.h>
 #include <plat/tc.h>
-#include <plat/board.h>
 #include <plat/keypad.h>
 #include <plat/board-sx1.h>
 
diff --git a/arch/arm/mach-omap1/board-voiceblue.c b/arch/arm/mach-omap1/board-voiceblue.c
index 3497769..1668af3 100644
--- a/arch/arm/mach-omap1/board-voiceblue.c
+++ b/arch/arm/mach-omap1/board-voiceblue.c
@@ -35,7 +35,6 @@
 #include <plat/flash.h>
 #include <plat/mux.h>
 #include <plat/tc.h>
-#include <plat/board.h>
 
 #include <mach/hardware.h>
 #include <mach/usb.h>
@@ -155,9 +154,6 @@
 	.pins[2]	= 6,
 };
 
-static struct omap_board_config_kernel voiceblue_config[] = {
-};
-
 #define MACHINE_PANICED		1
 #define MACHINE_REBOOTING	2
 #define MACHINE_REBOOT		4
@@ -275,8 +271,6 @@
 	voiceblue_smc91x_resources[1].start = gpio_to_irq(8);
 	voiceblue_smc91x_resources[1].end = gpio_to_irq(8);
 	platform_add_devices(voiceblue_devices, ARRAY_SIZE(voiceblue_devices));
-	omap_board_config = voiceblue_config;
-	omap_board_config_size = ARRAY_SIZE(voiceblue_config);
 	omap_serial_init();
 	omap1_usb_init(&voiceblue_usb_config);
 	omap_register_i2c_bus(1, 100, NULL, 0);
diff --git a/arch/arm/mach-omap1/clock_data.c b/arch/arm/mach-omap1/clock_data.c
index c007d80..6a32b9b 100644
--- a/arch/arm/mach-omap1/clock_data.c
+++ b/arch/arm/mach-omap1/clock_data.c
@@ -25,7 +25,6 @@
 #include <plat/clock.h>
 #include <plat/cpu.h>
 #include <plat/clkdev_omap.h>
-#include <plat/board.h>
 #include <plat/sram.h>	/* for omap_sram_reprogram_clock() */
 
 #include <mach/hardware.h>
@@ -788,7 +787,6 @@
 int __init omap1_clk_init(void)
 {
 	struct omap_clk *c;
-	const struct omap_clock_config *info;
 	int crystal_type = 0; /* Default 12 MHz */
 	u32 reg;
 
@@ -837,12 +835,6 @@
 	ck_dpll1_p = clk_get(NULL, "ck_dpll1");
 	ck_ref_p = clk_get(NULL, "ck_ref");
 
-	info = omap_get_config(OMAP_TAG_CLOCK, struct omap_clock_config);
-	if (info != NULL) {
-		if (!cpu_is_omap15xx())
-			crystal_type = info->system_clock_type;
-	}
-
 	if (cpu_is_omap7xx())
 		ck_ref.rate = 13000000;
 	if (cpu_is_omap16xx() && crystal_type == 2)
diff --git a/arch/arm/mach-omap1/devices.c b/arch/arm/mach-omap1/devices.c
index fa1fa4d..1feca35 100644
--- a/arch/arm/mach-omap1/devices.c
+++ b/arch/arm/mach-omap1/devices.c
@@ -20,7 +20,6 @@
 #include <asm/mach/map.h>
 
 #include <plat/tc.h>
-#include <plat/board.h>
 #include <plat/mux.h>
 #include <plat/dma.h>
 #include <plat/mmc.h>
diff --git a/arch/arm/mach-omap1/serial.c b/arch/arm/mach-omap1/serial.c
index 6809c9e..0d1709b 100644
--- a/arch/arm/mach-omap1/serial.c
+++ b/arch/arm/mach-omap1/serial.c
@@ -22,7 +22,6 @@
 
 #include <asm/mach-types.h>
 
-#include <plat/board.h>
 #include <plat/mux.h>
 #include <plat/fpga.h>
 
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index dd2db02..fcd4e85 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -62,13 +62,14 @@
 	select PM_OPP if PM
 	select USB_ARCH_HAS_EHCI if USB_SUPPORT
 	select ARM_CPU_SUSPEND if PM
-	select ARCH_NEEDS_CPU_IDLE_COUPLED
+	select ARCH_NEEDS_CPU_IDLE_COUPLED if SMP
 
 config SOC_OMAP5
 	bool "TI OMAP5"
 	select CPU_V7
 	select ARM_GIC
 	select HAVE_SMP
+	select ARM_CPU_SUSPEND if PM
 
 comment "OMAP Core Type"
 	depends on ARCH_OMAP2
diff --git a/arch/arm/mach-omap2/board-2430sdp.c b/arch/arm/mach-omap2/board-2430sdp.c
index 9511584..36eee4b 100644
--- a/arch/arm/mach-omap2/board-2430sdp.c
+++ b/arch/arm/mach-omap2/board-2430sdp.c
@@ -33,7 +33,6 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include <plat/board.h>
 #include "common.h"
 #include <plat/gpmc.h>
 #include <plat/usb.h>
diff --git a/arch/arm/mach-omap2/board-3430sdp.c b/arch/arm/mach-omap2/board-3430sdp.c
index a98c688..0f78cdb 100644
--- a/arch/arm/mach-omap2/board-3430sdp.c
+++ b/arch/arm/mach-omap2/board-3430sdp.c
@@ -31,7 +31,6 @@
 #include <asm/mach/map.h>
 
 #include <plat/mcspi.h>
-#include <plat/board.h>
 #include <plat/usb.h>
 #include "common.h"
 #include <plat/dma.h>
@@ -191,9 +190,6 @@
 	.default_device	= &sdp3430_lcd_device,
 };
 
-static struct omap_board_config_kernel sdp3430_config[] __initdata = {
-};
-
 static struct omap2_hsmmc_info mmc[] = {
 	{
 		.mmc		= 1,
@@ -576,8 +572,6 @@
 	int gpio_pendown;
 
 	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
-	omap_board_config = sdp3430_config;
-	omap_board_config_size = ARRAY_SIZE(sdp3430_config);
 	omap_hsmmc_init(mmc);
 	omap3430_i2c_init();
 	omap_display_init(&sdp3430_dss_data);
diff --git a/arch/arm/mach-omap2/board-3630sdp.c b/arch/arm/mach-omap2/board-3630sdp.c
index 2dc9ba5..8518b13 100644
--- a/arch/arm/mach-omap2/board-3630sdp.c
+++ b/arch/arm/mach-omap2/board-3630sdp.c
@@ -17,7 +17,6 @@
 #include <asm/mach/arch.h>
 
 #include "common.h"
-#include <plat/board.h>
 #include <plat/gpmc-smc91x.h>
 #include <plat/usb.h>
 
@@ -67,9 +66,6 @@
 	.reset_gpio_port[2]  = -EINVAL
 };
 
-static struct omap_board_config_kernel sdp_config[] __initdata = {
-};
-
 #ifdef CONFIG_OMAP_MUX
 static struct omap_board_mux board_mux[] __initdata = {
 	{ .reg_offset = OMAP_MUX_TERMINATOR },
@@ -197,8 +193,6 @@
 static void __init omap_sdp_init(void)
 {
 	omap3_mux_init(board_mux, OMAP_PACKAGE_CBP);
-	omap_board_config = sdp_config;
-	omap_board_config_size = ARRAY_SIZE(sdp_config);
 	zoom_peripherals_init();
 	omap_sdrc_init(h8mbx00u0mer0em_sdrc_params,
 				  h8mbx00u0mer0em_sdrc_params);
diff --git a/arch/arm/mach-omap2/board-4430sdp.c b/arch/arm/mach-omap2/board-4430sdp.c
index ad8a7d9..04e8574 100644
--- a/arch/arm/mach-omap2/board-4430sdp.c
+++ b/arch/arm/mach-omap2/board-4430sdp.c
@@ -34,7 +34,6 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include <plat/board.h>
 #include "common.h"
 #include <plat/usb.h>
 #include <plat/mmc.h>
diff --git a/arch/arm/mach-omap2/board-am3517crane.c b/arch/arm/mach-omap2/board-am3517crane.c
index 92432c2..de92b08 100644
--- a/arch/arm/mach-omap2/board-am3517crane.c
+++ b/arch/arm/mach-omap2/board-am3517crane.c
@@ -26,7 +26,6 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include <plat/board.h>
 #include "common.h"
 #include <plat/usb.h>
 
@@ -37,11 +36,6 @@
 #define GPIO_USB_POWER		35
 #define GPIO_USB_NRESET		38
 
-
-/* Board initialization */
-static struct omap_board_config_kernel am3517_crane_config[] __initdata = {
-};
-
 #ifdef CONFIG_OMAP_MUX
 static struct omap_board_mux board_mux[] __initdata = {
 	{ .reg_offset = OMAP_MUX_TERMINATOR },
@@ -67,9 +61,6 @@
 	omap_serial_init();
 	omap_sdrc_init(NULL, NULL);
 
-	omap_board_config = am3517_crane_config;
-	omap_board_config_size = ARRAY_SIZE(am3517_crane_config);
-
 	/* Configure GPIO for EHCI port */
 	if (omap_mux_init_gpio(GPIO_USB_NRESET, OMAP_PIN_OUTPUT)) {
 		pr_err("Can not configure mux for GPIO_USB_NRESET %d\n",
diff --git a/arch/arm/mach-omap2/board-am3517evm.c b/arch/arm/mach-omap2/board-am3517evm.c
index 18f6010..00abda1 100644
--- a/arch/arm/mach-omap2/board-am3517evm.c
+++ b/arch/arm/mach-omap2/board-am3517evm.c
@@ -32,7 +32,6 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include <plat/board.h>
 #include "common.h"
 #include <plat/usb.h>
 #include <video/omapdss.h>
@@ -324,9 +323,6 @@
 	platform_device_register(&am3517_hecc_device);
 }
 
-static struct omap_board_config_kernel am3517_evm_config[] __initdata = {
-};
-
 static struct omap2_hsmmc_info mmc[] = {
 	{
 		.mmc		= 1,
@@ -346,8 +342,6 @@
 
 static void __init am3517_evm_init(void)
 {
-	omap_board_config = am3517_evm_config;
-	omap_board_config_size = ARRAY_SIZE(am3517_evm_config);
 	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
 
 	am3517_evm_i2c_init();
diff --git a/arch/arm/mach-omap2/board-apollon.c b/arch/arm/mach-omap2/board-apollon.c
index e5fa46b..a6a1b48 100644
--- a/arch/arm/mach-omap2/board-apollon.c
+++ b/arch/arm/mach-omap2/board-apollon.c
@@ -35,7 +35,6 @@
 #include <asm/mach/flash.h>
 
 #include <plat/led.h>
-#include <plat/board.h>
 #include "common.h"
 #include <plat/gpmc.h>
 
diff --git a/arch/arm/mach-omap2/board-cm-t35.c b/arch/arm/mach-omap2/board-cm-t35.c
index 97d7190..d94a640 100644
--- a/arch/arm/mach-omap2/board-cm-t35.c
+++ b/arch/arm/mach-omap2/board-cm-t35.c
@@ -37,7 +37,6 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include <plat/board.h>
 #include "common.h"
 #include <plat/nand.h>
 #include <plat/gpmc.h>
@@ -714,13 +713,8 @@
 static inline void cm_t3730_init_mux(void) {}
 #endif
 
-static struct omap_board_config_kernel cm_t35_config[] __initdata = {
-};
-
 static void __init cm_t3x_common_init(void)
 {
-	omap_board_config = cm_t35_config;
-	omap_board_config_size = ARRAY_SIZE(cm_t35_config);
 	omap3_mux_init(board_mux, OMAP_PACKAGE_CUS);
 	omap_serial_init();
 	omap_sdrc_init(mt46h32m32lf6_sdrc_params,
diff --git a/arch/arm/mach-omap2/board-cm-t3517.c b/arch/arm/mach-omap2/board-cm-t3517.c
index a33ad46..57204f8 100644
--- a/arch/arm/mach-omap2/board-cm-t3517.c
+++ b/arch/arm/mach-omap2/board-cm-t3517.c
@@ -38,7 +38,6 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include <plat/board.h>
 #include "common.h"
 #include <plat/usb.h>
 #include <plat/nand.h>
@@ -249,9 +248,6 @@
 static inline void cm_t3517_init_nand(void) {}
 #endif
 
-static struct omap_board_config_kernel cm_t3517_config[] __initdata = {
-};
-
 #ifdef CONFIG_OMAP_MUX
 static struct omap_board_mux board_mux[] __initdata = {
 	/* GPIO186 - Green LED */
@@ -285,8 +281,6 @@
 	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
 	omap_serial_init();
 	omap_sdrc_init(NULL, NULL);
-	omap_board_config = cm_t3517_config;
-	omap_board_config_size = ARRAY_SIZE(cm_t3517_config);
 	cm_t3517_init_leds();
 	cm_t3517_init_nand();
 	cm_t3517_init_rtc();
diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 6567c1c..870a2a5 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -40,7 +40,6 @@
 #include <asm/mach/map.h>
 #include <asm/mach/flash.h>
 
-#include <plat/board.h>
 #include "common.h"
 #include <plat/gpmc.h>
 #include <plat/nand.h>
diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach-omap2/board-generic.c
index 6f93a20..38024a5 100644
--- a/arch/arm/mach-omap2/board-generic.c
+++ b/arch/arm/mach-omap2/board-generic.c
@@ -20,7 +20,6 @@
 #include <asm/hardware/gic.h>
 #include <asm/mach/arch.h>
 
-#include <plat/board.h>
 #include "common.h"
 #include "common-board-devices.h"
 
diff --git a/arch/arm/mach-omap2/board-h4.c b/arch/arm/mach-omap2/board-h4.c
index ace2048..5be30e6 100644
--- a/arch/arm/mach-omap2/board-h4.c
+++ b/arch/arm/mach-omap2/board-h4.c
@@ -32,11 +32,11 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include <plat/board.h>
 #include "common.h"
 #include <plat/menelaus.h>
 #include <plat/dma.h>
 #include <plat/gpmc.h>
+#include <plat/debug-devices.h>
 
 #include <video/omapdss.h>
 #include <video/omap-panel-generic-dpi.h>
diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c
index 7491529..01103b3 100644
--- a/arch/arm/mach-omap2/board-igep0020.c
+++ b/arch/arm/mach-omap2/board-igep0020.c
@@ -29,7 +29,6 @@
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 
-#include <plat/board.h>
 #include "common.h"
 #include <plat/gpmc.h>
 #include <plat/usb.h>
@@ -554,6 +553,8 @@
 
 #ifdef CONFIG_OMAP_MUX
 static struct omap_board_mux board_mux[] __initdata = {
+	/* SMSC9221 LAN Controller ETH IRQ (GPIO_176) */
+	OMAP3_MUX(MCSPI1_CS2, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
 	{ .reg_offset = OMAP_MUX_TERMINATOR },
 };
 #endif
diff --git a/arch/arm/mach-omap2/board-ldp.c b/arch/arm/mach-omap2/board-ldp.c
index ef9e829..c37c2a1 100644
--- a/arch/arm/mach-omap2/board-ldp.c
+++ b/arch/arm/mach-omap2/board-ldp.c
@@ -35,7 +35,6 @@
 #include <asm/mach/map.h>
 
 #include <plat/mcspi.h>
-#include <plat/board.h>
 #include "common.h"
 #include <plat/gpmc.h>
 #include <mach/board-zoom.h>
diff --git a/arch/arm/mach-omap2/board-n8x0.c b/arch/arm/mach-omap2/board-n8x0.c
index 677357f..5397209 100644
--- a/arch/arm/mach-omap2/board-n8x0.c
+++ b/arch/arm/mach-omap2/board-n8x0.c
@@ -25,7 +25,6 @@
 #include <asm/mach/arch.h>
 #include <asm/mach-types.h>
 
-#include <plat/board.h>
 #include "common.h"
 #include <plat/menelaus.h>
 #include <mach/irqs.h>
diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c
index 6202fc7..293e3b2 100644
--- a/arch/arm/mach-omap2/board-omap3beagle.c
+++ b/arch/arm/mach-omap2/board-omap3beagle.c
@@ -39,7 +39,6 @@
 #include <asm/mach/map.h>
 #include <asm/mach/flash.h>
 
-#include <plat/board.h>
 #include "common.h"
 #include <video/omapdss.h>
 #include <video/omap-panel-tfp410.h>
diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
index ef230a0..851aec6 100644
--- a/arch/arm/mach-omap2/board-omap3evm.c
+++ b/arch/arm/mach-omap2/board-omap3evm.c
@@ -45,7 +45,6 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include <plat/board.h>
 #include <plat/usb.h>
 #include <plat/nand.h>
 #include "common.h"
@@ -58,6 +57,7 @@
 #include "hsmmc.h"
 #include "common-board-devices.h"
 
+#define OMAP3_EVM_TS_GPIO	175
 #define OMAP3_EVM_EHCI_VBUS	22
 #define OMAP3_EVM_EHCI_SELECT	61
 
@@ -74,6 +74,18 @@
 #define OMAP3EVM_GEN1_ETHR_GPIO_RST	64
 #define OMAP3EVM_GEN2_ETHR_GPIO_RST	7
 
+/*
+ * OMAP35x EVM revision
+ * Run time detection of EVM revision is done by reading Ethernet
+ * PHY ID -
+ *	GEN_1	= 0x01150000
+ *	GEN_2	= 0x92200000
+ */
+enum {
+	OMAP3EVM_BOARD_GEN_1 = 0,	/* EVM Rev between  A - D */
+	OMAP3EVM_BOARD_GEN_2,		/* EVM Rev >= Rev E */
+};
+
 static u8 omap3_evm_version;
 
 u8 get_omap3_evm_rev(void)
@@ -525,9 +537,6 @@
 	return 0;
 }
 
-static struct omap_board_config_kernel omap3_evm_config[] __initdata = {
-};
-
 static struct usbhs_omap_board_data usbhs_bdata __initdata = {
 
 	.port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
@@ -687,9 +696,6 @@
 	obm = (cpu_is_omap3630()) ? omap36x_board_mux : omap35x_board_mux;
 	omap3_mux_init(obm, OMAP_PACKAGE_CBB);
 
-	omap_board_config = omap3_evm_config;
-	omap_board_config_size = ARRAY_SIZE(omap3_evm_config);
-
 	omap_mux_init_gpio(63, OMAP_PIN_INPUT);
 	omap_hsmmc_init(mmc);
 
diff --git a/arch/arm/mach-omap2/board-omap3logic.c b/arch/arm/mach-omap2/board-omap3logic.c
index fca93d1..a63a49d 100644
--- a/arch/arm/mach-omap2/board-omap3logic.c
+++ b/arch/arm/mach-omap2/board-omap3logic.c
@@ -41,7 +41,6 @@
 #include "common-board-devices.h"
 
 #include <plat/mux.h>
-#include <plat/board.h>
 #include "common.h"
 #include <plat/gpmc-smsc911x.h>
 #include <plat/gpmc.h>
diff --git a/arch/arm/mach-omap2/board-omap3pandora.c b/arch/arm/mach-omap2/board-omap3pandora.c
index 57aebee..633c445 100644
--- a/arch/arm/mach-omap2/board-omap3pandora.c
+++ b/arch/arm/mach-omap2/board-omap3pandora.c
@@ -40,7 +40,6 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include <plat/board.h>
 #include "common.h"
 #include <mach/hardware.h>
 #include <plat/mcspi.h>
diff --git a/arch/arm/mach-omap2/board-omap3stalker.c b/arch/arm/mach-omap2/board-omap3stalker.c
index b318f56..421fb8e 100644
--- a/arch/arm/mach-omap2/board-omap3stalker.c
+++ b/arch/arm/mach-omap2/board-omap3stalker.c
@@ -35,7 +35,6 @@
 #include <asm/mach/map.h>
 #include <asm/mach/flash.h>
 
-#include <plat/board.h>
 #include "common.h"
 #include <plat/gpmc.h>
 #include <plat/nand.h>
@@ -362,9 +361,6 @@
 
 #define OMAP3_STALKER_TS_GPIO	175
 
-static struct omap_board_config_kernel omap3_stalker_config[] __initdata = {
-};
-
 static struct platform_device *omap3_stalker_devices[] __initdata = {
 	&keys_gpio,
 };
@@ -399,8 +395,6 @@
 {
 	regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
 	omap3_mux_init(board_mux, OMAP_PACKAGE_CUS);
-	omap_board_config = omap3_stalker_config;
-	omap_board_config_size = ARRAY_SIZE(omap3_stalker_config);
 
 	omap_mux_init_gpio(23, OMAP_PIN_INPUT);
 	omap_hsmmc_init(mmc);
diff --git a/arch/arm/mach-omap2/board-omap3touchbook.c b/arch/arm/mach-omap2/board-omap3touchbook.c
index 485d14d..d3556c9 100644
--- a/arch/arm/mach-omap2/board-omap3touchbook.c
+++ b/arch/arm/mach-omap2/board-omap3touchbook.c
@@ -44,7 +44,6 @@
 #include <asm/mach/flash.h>
 #include <asm/system_info.h>
 
-#include <plat/board.h>
 #include "common.h"
 #include <plat/gpmc.h>
 #include <plat/nand.h>
diff --git a/arch/arm/mach-omap2/board-omap4panda.c b/arch/arm/mach-omap2/board-omap4panda.c
index 70f6d1d..3911c13 100644
--- a/arch/arm/mach-omap2/board-omap4panda.c
+++ b/arch/arm/mach-omap2/board-omap4panda.c
@@ -39,7 +39,6 @@
 #include <asm/mach/map.h>
 #include <video/omapdss.h>
 
-#include <plat/board.h>
 #include "common.h"
 #include <plat/usb.h>
 #include <plat/mmc.h>
diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c
index 779734d..193d160 100644
--- a/arch/arm/mach-omap2/board-overo.c
+++ b/arch/arm/mach-omap2/board-overo.c
@@ -42,7 +42,6 @@
 #include <asm/mach/flash.h>
 #include <asm/mach/map.h>
 
-#include <plat/board.h>
 #include "common.h"
 #include <video/omapdss.h>
 #include <video/omap-panel-generic-dpi.h>
diff --git a/arch/arm/mach-omap2/board-rx51-peripherals.c b/arch/arm/mach-omap2/board-rx51-peripherals.c
index df2534d..3b9fc61 100644
--- a/arch/arm/mach-omap2/board-rx51-peripherals.c
+++ b/arch/arm/mach-omap2/board-rx51-peripherals.c
@@ -28,7 +28,6 @@
 #include <asm/system_info.h>
 
 #include <plat/mcspi.h>
-#include <plat/board.h>
 #include "common.h"
 #include <plat/dma.h>
 #include <plat/gpmc.h>
diff --git a/arch/arm/mach-omap2/board-rx51.c b/arch/arm/mach-omap2/board-rx51.c
index 345dd93..92924eb 100644
--- a/arch/arm/mach-omap2/board-rx51.c
+++ b/arch/arm/mach-omap2/board-rx51.c
@@ -24,7 +24,6 @@
 #include <asm/mach/map.h>
 
 #include <plat/mcspi.h>
-#include <plat/board.h>
 #include "common.h"
 #include <plat/dma.h>
 #include <plat/gpmc.h>
diff --git a/arch/arm/mach-omap2/board-ti8168evm.c b/arch/arm/mach-omap2/board-ti8168evm.c
index d4c8392..da4679d 100644
--- a/arch/arm/mach-omap2/board-ti8168evm.c
+++ b/arch/arm/mach-omap2/board-ti8168evm.c
@@ -21,7 +21,6 @@
 #include <asm/mach/map.h>
 
 #include <plat/irqs.h>
-#include <plat/board.h>
 #include "common.h"
 #include <plat/usb.h>
 
@@ -32,15 +31,10 @@
 	.power		= 500,
 };
 
-static struct omap_board_config_kernel ti81xx_evm_config[] __initdata = {
-};
-
 static void __init ti81xx_evm_init(void)
 {
 	omap_serial_init();
 	omap_sdrc_init(NULL, NULL);
-	omap_board_config = ti81xx_evm_config;
-	omap_board_config_size = ARRAY_SIZE(ti81xx_evm_config);
 	usb_musb_init(&musb_board_data);
 }
 
diff --git a/arch/arm/mach-omap2/board-zoom.c b/arch/arm/mach-omap2/board-zoom.c
index 4e7e561..4994438 100644
--- a/arch/arm/mach-omap2/board-zoom.c
+++ b/arch/arm/mach-omap2/board-zoom.c
@@ -22,7 +22,6 @@
 #include <asm/mach/arch.h>
 
 #include "common.h"
-#include <plat/board.h>
 #include <plat/usb.h>
 
 #include <mach/board-zoom.h>
diff --git a/arch/arm/mach-omap2/common-board-devices.c b/arch/arm/mach-omap2/common-board-devices.c
index 1473474..c187586 100644
--- a/arch/arm/mach-omap2/common-board-devices.c
+++ b/arch/arm/mach-omap2/common-board-devices.c
@@ -35,16 +35,6 @@
 	.turbo_mode	= 0,
 };
 
-/*
- * ADS7846 driver maybe request a gpio according to the value
- * of pdata->get_pendown_state, but we have done this. So set
- * get_pendown_state to avoid twice gpio requesting.
- */
-static int omap3_get_pendown_state(void)
-{
-	return !gpio_get_value(OMAP3_EVM_TS_GPIO);
-}
-
 static struct ads7846_platform_data ads7846_config = {
 	.x_max			= 0x0fff,
 	.y_max			= 0x0fff,
@@ -55,7 +45,6 @@
 	.debounce_rep		= 1,
 	.gpio_pendown		= -EINVAL,
 	.keep_vref_on		= 1,
-	.get_pendown_state	= &omap3_get_pendown_state,
 };
 
 static struct spi_board_info ads7846_spi_board_info __initdata = {
diff --git a/arch/arm/mach-omap2/common-board-devices.h b/arch/arm/mach-omap2/common-board-devices.h
index 4c4ef6a..a0b4a428 100644
--- a/arch/arm/mach-omap2/common-board-devices.h
+++ b/arch/arm/mach-omap2/common-board-devices.h
@@ -4,7 +4,6 @@
 #include "twl-common.h"
 
 #define NAND_BLOCK_SIZE	SZ_128K
-#define OMAP3_EVM_TS_GPIO	175
 
 struct mtd_partition;
 struct ads7846_platform_data;
diff --git a/arch/arm/mach-omap2/common.c b/arch/arm/mach-omap2/common.c
index 069f972..6c2ff4f 100644
--- a/arch/arm/mach-omap2/common.c
+++ b/arch/arm/mach-omap2/common.c
@@ -18,7 +18,6 @@
 #include <linux/io.h>
 
 #include <plat/hardware.h>
-#include <plat/board.h>
 #include <plat/mux.h>
 #include <plat/clock.h>
 
diff --git a/arch/arm/mach-omap2/cpuidle44xx.c b/arch/arm/mach-omap2/cpuidle44xx.c
index ee05e19..288bee6 100644
--- a/arch/arm/mach-omap2/cpuidle44xx.c
+++ b/arch/arm/mach-omap2/cpuidle44xx.c
@@ -238,8 +238,9 @@
 	for_each_cpu(cpu_id, cpu_online_mask) {
 		dev = &per_cpu(omap4_idle_dev, cpu_id);
 		dev->cpu = cpu_id;
+#ifdef CONFIG_ARCH_NEEDS_CPU_IDLE_COUPLED
 		dev->coupled_cpus = *cpu_online_mask;
-
+#endif
 		cpuidle_register_driver(&omap4_idle_driver);
 
 		if (cpuidle_register_device(dev)) {
diff --git a/arch/arm/mach-omap2/devices.c b/arch/arm/mach-omap2/devices.c
index c00c689..56dfa2df 100644
--- a/arch/arm/mach-omap2/devices.c
+++ b/arch/arm/mach-omap2/devices.c
@@ -26,7 +26,6 @@
 #include <asm/pmu.h>
 
 #include "iomap.h"
-#include <plat/board.h>
 #include <plat/dma.h>
 #include <plat/omap_hwmod.h>
 #include <plat/omap_device.h>
diff --git a/arch/arm/mach-omap2/gpmc-nand.c b/arch/arm/mach-omap2/gpmc-nand.c
index 045596a..96fcc641 100644
--- a/arch/arm/mach-omap2/gpmc-nand.c
+++ b/arch/arm/mach-omap2/gpmc-nand.c
@@ -18,7 +18,6 @@
 
 #include <plat/cpu.h>
 #include <plat/nand.h>
-#include <plat/board.h>
 #include <plat/gpmc.h>
 
 static struct resource gpmc_nand_resource[] = {
diff --git a/arch/arm/mach-omap2/gpmc-onenand.c b/arch/arm/mach-omap2/gpmc-onenand.c
index 71d7c07..b12a39e 100644
--- a/arch/arm/mach-omap2/gpmc-onenand.c
+++ b/arch/arm/mach-omap2/gpmc-onenand.c
@@ -20,7 +20,6 @@
 
 #include <plat/cpu.h>
 #include <plat/onenand.h>
-#include <plat/board.h>
 #include <plat/gpmc.h>
 
 #define	ONENAND_IO_SIZE	SZ_128K
diff --git a/arch/arm/mach-omap2/gpmc-smc91x.c b/arch/arm/mach-omap2/gpmc-smc91x.c
index ba10c24..3f75ff0 100644
--- a/arch/arm/mach-omap2/gpmc-smc91x.c
+++ b/arch/arm/mach-omap2/gpmc-smc91x.c
@@ -17,7 +17,6 @@
 #include <linux/io.h>
 #include <linux/smc91x.h>
 
-#include <plat/board.h>
 #include <plat/gpmc.h>
 #include <plat/gpmc-smc91x.h>
 
diff --git a/arch/arm/mach-omap2/gpmc-smsc911x.c b/arch/arm/mach-omap2/gpmc-smsc911x.c
index b6c77be..a3a2887 100644
--- a/arch/arm/mach-omap2/gpmc-smsc911x.c
+++ b/arch/arm/mach-omap2/gpmc-smsc911x.c
@@ -20,7 +20,6 @@
 #include <linux/io.h>
 #include <linux/smsc911x.h>
 
-#include <plat/board.h>
 #include <plat/gpmc.h>
 #include <plat/gpmc-smsc911x.h>
 
diff --git a/arch/arm/mach-omap2/mux.h b/arch/arm/mach-omap2/mux.h
index 471e62a7..76f9b3c 100644
--- a/arch/arm/mach-omap2/mux.h
+++ b/arch/arm/mach-omap2/mux.h
@@ -127,7 +127,6 @@
  * @gpio:	GPIO number
  * @muxnames:	available signal modes for a ball
  * @balls:	available balls on the package
- * @partition:	mux partition
  */
 struct omap_mux {
 	u16	reg_offset;
diff --git a/arch/arm/mach-omap2/opp4xxx_data.c b/arch/arm/mach-omap2/opp4xxx_data.c
index 2293ba2..c95415d 100644
--- a/arch/arm/mach-omap2/opp4xxx_data.c
+++ b/arch/arm/mach-omap2/opp4xxx_data.c
@@ -94,7 +94,7 @@
 {
 	int r = -ENODEV;
 
-	if (!cpu_is_omap44xx())
+	if (!cpu_is_omap443x())
 		return r;
 
 	r = omap_init_opp_table(omap44xx_opp_def_list,
diff --git a/arch/arm/mach-omap2/pm-debug.c b/arch/arm/mach-omap2/pm-debug.c
index 814bcd9..3e1345f 100644
--- a/arch/arm/mach-omap2/pm-debug.c
+++ b/arch/arm/mach-omap2/pm-debug.c
@@ -28,7 +28,6 @@
 #include <linux/slab.h>
 
 #include <plat/clock.h>
-#include <plat/board.h>
 #include "powerdomain.h"
 #include "clockdomain.h"
 #include <plat/dmtimer.h>
diff --git a/arch/arm/mach-omap2/pm24xx.c b/arch/arm/mach-omap2/pm24xx.c
index 2edeffc..de1caf1 100644
--- a/arch/arm/mach-omap2/pm24xx.c
+++ b/arch/arm/mach-omap2/pm24xx.c
@@ -38,7 +38,6 @@
 #include <plat/clock.h>
 #include <plat/sram.h>
 #include <plat/dma.h>
-#include <plat/board.h>
 
 #include <mach/irqs.h>
 
@@ -352,16 +351,6 @@
 
 	prcm_setup_regs();
 
-	/* Hack to prevent MPU retention when STI console is enabled. */
-	{
-		const struct omap_sti_console_config *sti;
-
-		sti = omap_get_config(OMAP_TAG_STI_CONSOLE,
-				      struct omap_sti_console_config);
-		if (sti != NULL && sti->enable)
-			sti_console_enabled = 1;
-	}
-
 	/*
 	 * We copy the assembler sleep/wakeup routines to SRAM.
 	 * These routines need to be in SRAM as that's the only
diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c
index e4fc88c..05bd8f0 100644
--- a/arch/arm/mach-omap2/pm34xx.c
+++ b/arch/arm/mach-omap2/pm34xx.c
@@ -272,21 +272,16 @@
 	per_next_state = pwrdm_read_next_pwrst(per_pwrdm);
 	core_next_state = pwrdm_read_next_pwrst(core_pwrdm);
 
-	if (mpu_next_state < PWRDM_POWER_ON) {
-		pwrdm_pre_transition(mpu_pwrdm);
-		pwrdm_pre_transition(neon_pwrdm);
-	}
+	pwrdm_pre_transition(NULL);
 
 	/* PER */
 	if (per_next_state < PWRDM_POWER_ON) {
-		pwrdm_pre_transition(per_pwrdm);
 		per_going_off = (per_next_state == PWRDM_POWER_OFF) ? 1 : 0;
 		omap2_gpio_prepare_for_idle(per_going_off);
 	}
 
 	/* CORE */
 	if (core_next_state < PWRDM_POWER_ON) {
-		pwrdm_pre_transition(core_pwrdm);
 		if (core_next_state == PWRDM_POWER_OFF) {
 			omap3_core_save_context();
 			omap3_cm_save_context();
@@ -339,20 +334,14 @@
 			omap2_prm_clear_mod_reg_bits(OMAP3430_AUTO_OFF_MASK,
 					       OMAP3430_GR_MOD,
 					       OMAP3_PRM_VOLTCTRL_OFFSET);
-		pwrdm_post_transition(core_pwrdm);
 	}
 	omap3_intc_resume_idle();
 
-	/* PER */
-	if (per_next_state < PWRDM_POWER_ON) {
-		omap2_gpio_resume_after_idle();
-		pwrdm_post_transition(per_pwrdm);
-	}
+	pwrdm_post_transition(NULL);
 
-	if (mpu_next_state < PWRDM_POWER_ON) {
-		pwrdm_post_transition(mpu_pwrdm);
-		pwrdm_post_transition(neon_pwrdm);
-	}
+	/* PER */
+	if (per_next_state < PWRDM_POWER_ON)
+		omap2_gpio_resume_after_idle();
 }
 
 static void omap3_pm_idle(void)
diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c
index c1b93c7..d77f018 100644
--- a/arch/arm/mach-omap2/serial.c
+++ b/arch/arm/mach-omap2/serial.c
@@ -29,7 +29,6 @@
 
 #include <plat/omap-serial.h>
 #include "common.h"
-#include <plat/board.h>
 #include <plat/dma.h>
 #include <plat/omap_hwmod.h>
 #include <plat/omap_device.h>
@@ -81,8 +80,9 @@
 };
 
 #ifdef CONFIG_PM
-static void omap_uart_enable_wakeup(struct platform_device *pdev, bool enable)
+static void omap_uart_enable_wakeup(struct device *dev, bool enable)
 {
+	struct platform_device *pdev = to_platform_device(dev);
 	struct omap_device *od = to_omap_device(pdev);
 
 	if (!od)
@@ -99,15 +99,17 @@
  * in Smartidle Mode When Configured for DMA Operations.
  * WA: configure uart in force idle mode.
  */
-static void omap_uart_set_noidle(struct platform_device *pdev)
+static void omap_uart_set_noidle(struct device *dev)
 {
+	struct platform_device *pdev = to_platform_device(dev);
 	struct omap_device *od = to_omap_device(pdev);
 
 	omap_hwmod_set_slave_idlemode(od->hwmods[0], HWMOD_IDLEMODE_NO);
 }
 
-static void omap_uart_set_smartidle(struct platform_device *pdev)
+static void omap_uart_set_smartidle(struct device *dev)
 {
+	struct platform_device *pdev = to_platform_device(dev);
 	struct omap_device *od = to_omap_device(pdev);
 	u8 idlemode;
 
@@ -120,10 +122,10 @@
 }
 
 #else
-static void omap_uart_enable_wakeup(struct platform_device *pdev, bool enable)
+static void omap_uart_enable_wakeup(struct device *dev, bool enable)
 {}
-static void omap_uart_set_noidle(struct platform_device *pdev) {}
-static void omap_uart_set_smartidle(struct platform_device *pdev) {}
+static void omap_uart_set_noidle(struct device *dev) {}
+static void omap_uart_set_smartidle(struct device *dev) {}
 #endif /* CONFIG_PM */
 
 #ifdef CONFIG_OMAP_MUX
@@ -304,6 +306,9 @@
 	omap_up.dma_rx_timeout = info->dma_rx_timeout;
 	omap_up.dma_rx_poll_rate = info->dma_rx_poll_rate;
 	omap_up.autosuspend_timeout = info->autosuspend_timeout;
+	omap_up.DTR_gpio = info->DTR_gpio;
+	omap_up.DTR_inverted = info->DTR_inverted;
+	omap_up.DTR_present = info->DTR_present;
 
 	pdata = &omap_up;
 	pdata_size = sizeof(struct omap_uart_port_info);
diff --git a/arch/arm/mach-omap2/sleep44xx.S b/arch/arm/mach-omap2/sleep44xx.S
index 9f6b83d..91e71d8 100644
--- a/arch/arm/mach-omap2/sleep44xx.S
+++ b/arch/arm/mach-omap2/sleep44xx.S
@@ -56,9 +56,13 @@
  * The restore function pointer is stored at CPUx_WAKEUP_NS_PA_ADDR_OFFSET.
  * It returns to the caller for CPU INACTIVE and ON power states or in case
  * CPU failed to transition to targeted OFF/DORMANT state.
+ *
+ * omap4_finish_suspend() calls v7_flush_dcache_all() which doesn't save
+ * stack frame and it expects the caller to take care of it. Hence the entire
+ * stack frame is saved to avoid possible stack corruption.
  */
 ENTRY(omap4_finish_suspend)
-	stmfd	sp!, {lr}
+	stmfd	sp!, {r4-r12, lr}
 	cmp	r0, #0x0
 	beq	do_WFI				@ No lowpower state, jump to WFI
 
@@ -226,7 +230,7 @@
 skip_scu_gp_clear:
 	isb
 	dsb
-	ldmfd	sp!, {pc}
+	ldmfd	sp!, {r4-r12, pc}
 ENDPROC(omap4_finish_suspend)
 
 /*
diff --git a/arch/arm/mach-omap2/twl-common.c b/arch/arm/mach-omap2/twl-common.c
index de47f17..db5ff66 100644
--- a/arch/arm/mach-omap2/twl-common.c
+++ b/arch/arm/mach-omap2/twl-common.c
@@ -67,6 +67,7 @@
 			   const char *pmic_type, int pmic_irq,
 			   struct twl4030_platform_data *pmic_data)
 {
+	omap_mux_init_signal("sys_nirq", OMAP_PIN_INPUT_PULLUP | OMAP_PIN_OFF_WAKEUPENABLE);
 	strncpy(pmic_i2c_board_info.type, pmic_type,
 		sizeof(pmic_i2c_board_info.type));
 	pmic_i2c_board_info.irq = pmic_irq;
diff --git a/arch/arm/mach-orion5x/common.c b/arch/arm/mach-orion5x/common.c
index 9148b22..410291c 100644
--- a/arch/arm/mach-orion5x/common.c
+++ b/arch/arm/mach-orion5x/common.c
@@ -109,7 +109,8 @@
 {
 	orion_ge00_init(eth_data,
 			ORION5X_ETH_PHYS_BASE, IRQ_ORION5X_ETH_SUM,
-			IRQ_ORION5X_ETH_ERR);
+			IRQ_ORION5X_ETH_ERR,
+			MV643XX_TX_CSUM_DEFAULT_LIMIT);
 }
 
 
diff --git a/arch/arm/mach-s3c24xx/include/mach/dma.h b/arch/arm/mach-s3c24xx/include/mach/dma.h
index 454831b..ee99fd5 100644
--- a/arch/arm/mach-s3c24xx/include/mach/dma.h
+++ b/arch/arm/mach-s3c24xx/include/mach/dma.h
@@ -24,7 +24,8 @@
 */
 
 enum dma_ch {
-	DMACH_XD0,
+	DMACH_DT_PROP = -1,	/* not yet supported, do not use */
+	DMACH_XD0 = 0,
 	DMACH_XD1,
 	DMACH_SDI,
 	DMACH_SPI0,
diff --git a/arch/arm/mach-shmobile/board-armadillo800eva.c b/arch/arm/mach-shmobile/board-armadillo800eva.c
index cf10f92..453a6e5 100644
--- a/arch/arm/mach-shmobile/board-armadillo800eva.c
+++ b/arch/arm/mach-shmobile/board-armadillo800eva.c
@@ -520,13 +520,14 @@
 };
 
 /* GPIO KEY */
-#define GPIO_KEY(c, g, d) { .code = c, .gpio = g, .desc = d, .active_low = 1 }
+#define GPIO_KEY(c, g, d, ...) \
+	{ .code = c, .gpio = g, .desc = d, .active_low = 1, __VA_ARGS__ }
 
 static struct gpio_keys_button gpio_buttons[] = {
-	GPIO_KEY(KEY_POWER,	GPIO_PORT99,	"SW1"),
-	GPIO_KEY(KEY_BACK,	GPIO_PORT100,	"SW2"),
-	GPIO_KEY(KEY_MENU,	GPIO_PORT97,	"SW3"),
-	GPIO_KEY(KEY_HOME,	GPIO_PORT98,	"SW4"),
+	GPIO_KEY(KEY_POWER,	GPIO_PORT99,	"SW3", .wakeup = 1),
+	GPIO_KEY(KEY_BACK,	GPIO_PORT100,	"SW4"),
+	GPIO_KEY(KEY_MENU,	GPIO_PORT97,	"SW5"),
+	GPIO_KEY(KEY_HOME,	GPIO_PORT98,	"SW6"),
 };
 
 static struct gpio_keys_platform_data gpio_key_info = {
@@ -901,8 +902,8 @@
 	&camera_device,
 	&ceu0_device,
 	&fsi_device,
-	&fsi_hdmi_device,
 	&fsi_wm8978_device,
+	&fsi_hdmi_device,
 };
 
 static void __init eva_clock_init(void)
diff --git a/arch/arm/mach-shmobile/board-mackerel.c b/arch/arm/mach-shmobile/board-mackerel.c
index 7ea2b31..c129542 100644
--- a/arch/arm/mach-shmobile/board-mackerel.c
+++ b/arch/arm/mach-shmobile/board-mackerel.c
@@ -695,6 +695,7 @@
  *  - J30 "open"
  *  - modify usbhs1_get_id() USBHS_HOST -> USBHS_GADGET
  *  - add .get_vbus = usbhs_get_vbus in usbhs1_private
+ *  - check usbhs0_device(pio)/usbhs1_device(irq) order in mackerel_devices.
  */
 #define IRQ8 evt2irq(0x0300)
 #define USB_PHY_MODE		(1 << 4)
@@ -1325,8 +1326,8 @@
 	&nor_flash_device,
 	&smc911x_device,
 	&lcdc_device,
-	&usbhs1_device,
 	&usbhs0_device,
+	&usbhs1_device,
 	&leds_device,
 	&fsi_device,
 	&fsi_ak4643_device,
diff --git a/arch/arm/mach-shmobile/board-marzen.c b/arch/arm/mach-shmobile/board-marzen.c
index 3a528cf..fcf5a47 100644
--- a/arch/arm/mach-shmobile/board-marzen.c
+++ b/arch/arm/mach-shmobile/board-marzen.c
@@ -67,7 +67,7 @@
 
 static struct platform_device eth_device = {
 	.name		= "smsc911x",
-	.id		= 0,
+	.id		= -1,
 	.dev  = {
 		.platform_data = &smsc911x_platdata,
 	},
diff --git a/arch/arm/mach-shmobile/intc-sh73a0.c b/arch/arm/mach-shmobile/intc-sh73a0.c
index ee44740..588555a 100644
--- a/arch/arm/mach-shmobile/intc-sh73a0.c
+++ b/arch/arm/mach-shmobile/intc-sh73a0.c
@@ -259,9 +259,9 @@
 	return 0; /* always allow wakeup */
 }
 
-#define RELOC_BASE 0x1000
+#define RELOC_BASE 0x1200
 
-/* INTCA IRQ pins at INTCS + 0x1000 to make space for GIC+INTC handling */
+/* INTCA IRQ pins at INTCS + RELOC_BASE to make space for GIC+INTC handling */
 #define INTCS_VECT_RELOC(n, vect) INTCS_VECT((n), (vect) + RELOC_BASE)
 
 INTC_IRQ_PINS_32(intca_irq_pins, 0xe6900000,
diff --git a/arch/arm/mach-ux500/Kconfig b/arch/arm/mach-ux500/Kconfig
index c013bbf..53d3d46 100644
--- a/arch/arm/mach-ux500/Kconfig
+++ b/arch/arm/mach-ux500/Kconfig
@@ -41,7 +41,6 @@
 config MACH_SNOWBALL
 	bool "U8500 Snowball platform"
 	select MACH_MOP500
-	select LEDS_GPIO
 	help
 	  Include support for the snowball development platform.
 
diff --git a/arch/arm/mach-ux500/board-mop500-msp.c b/arch/arm/mach-ux500/board-mop500-msp.c
index 9960480..df15646 100644
--- a/arch/arm/mach-ux500/board-mop500-msp.c
+++ b/arch/arm/mach-ux500/board-mop500-msp.c
@@ -191,9 +191,9 @@
 	return pdev;
 }
 
-/* Platform device for ASoC U8500 machine */
-static struct platform_device snd_soc_u8500 = {
-		.name = "snd-soc-u8500",
+/* Platform device for ASoC MOP500 machine */
+static struct platform_device snd_soc_mop500 = {
+		.name = "snd-soc-mop500",
 		.id = 0,
 		.dev = {
 			.platform_data = NULL,
@@ -227,8 +227,8 @@
 {
 	struct platform_device *msp1;
 
-	pr_info("%s: Register platform-device 'snd-soc-u8500'.\n", __func__);
-	platform_device_register(&snd_soc_u8500);
+	pr_info("%s: Register platform-device 'snd-soc-mop500'.\n", __func__);
+	platform_device_register(&snd_soc_mop500);
 
 	pr_info("Initialize MSP I2S-devices.\n");
 	db8500_add_msp_i2s(parent, 0, U8500_MSP0_BASE, IRQ_DB8500_MSP0,
diff --git a/arch/arm/mach-ux500/board-mop500.c b/arch/arm/mach-ux500/board-mop500.c
index 8674a89..1d2e3c6 100644
--- a/arch/arm/mach-ux500/board-mop500.c
+++ b/arch/arm/mach-ux500/board-mop500.c
@@ -524,33 +524,12 @@
 };
 #endif
 
-#define PRCC_K_SOFTRST_SET      0x18
-#define PRCC_K_SOFTRST_CLEAR    0x1C
-static void ux500_uart0_reset(void)
-{
-	void __iomem *prcc_rst_set, *prcc_rst_clr;
-
-	prcc_rst_set = (void __iomem *)IO_ADDRESS(U8500_CLKRST1_BASE +
-			PRCC_K_SOFTRST_SET);
-	prcc_rst_clr = (void __iomem *)IO_ADDRESS(U8500_CLKRST1_BASE +
-			PRCC_K_SOFTRST_CLEAR);
-
-	/* Activate soft reset PRCC_K_SOFTRST_CLEAR */
-	writel((readl(prcc_rst_clr) | 0x1), prcc_rst_clr);
-	udelay(1);
-
-	/* Release soft reset PRCC_K_SOFTRST_SET */
-	writel((readl(prcc_rst_set) | 0x1), prcc_rst_set);
-	udelay(1);
-}
-
 static struct amba_pl011_data uart0_plat = {
 #ifdef CONFIG_STE_DMA40
 	.dma_filter = stedma40_filter,
 	.dma_rx_param = &uart0_dma_cfg_rx,
 	.dma_tx_param = &uart0_dma_cfg_tx,
 #endif
-	.reset = ux500_uart0_reset,
 };
 
 static struct amba_pl011_data uart1_plat = {
@@ -797,6 +776,7 @@
 				ARRAY_SIZE(mop500_platform_devs));
 
 		mop500_sdi_init(parent);
+		mop500_msp_init(parent);
 		i2c0_devs = ARRAY_SIZE(mop500_i2c0_devices);
 		i2c_register_board_info(0, mop500_i2c0_devices, i2c0_devs);
 		i2c_register_board_info(2, mop500_i2c2_devices,
@@ -804,6 +784,8 @@
 
 		mop500_uib_init();
 
+	} else if (of_machine_is_compatible("calaosystems,snowball-a9500")) {
+		mop500_msp_init(parent);
 	} else if (of_machine_is_compatible("st-ericsson,hrefv60+")) {
 		/*
 		 * The HREFv60 board removed a GPIO expander and routed
@@ -815,6 +797,7 @@
 				ARRAY_SIZE(mop500_platform_devs));
 
 		hrefv60_sdi_init(parent);
+		mop500_msp_init(parent);
 
 		i2c0_devs = ARRAY_SIZE(mop500_i2c0_devices);
 		i2c0_devs -= NUM_PRE_V60_I2C0_DEVICES;
diff --git a/arch/arm/mm/dma-mapping.c b/arch/arm/mm/dma-mapping.c
index 4e7d118..051204f 100644
--- a/arch/arm/mm/dma-mapping.c
+++ b/arch/arm/mm/dma-mapping.c
@@ -267,17 +267,19 @@
 	vunmap(cpu_addr);
 }
 
+#define DEFAULT_DMA_COHERENT_POOL_SIZE	SZ_256K
+
 struct dma_pool {
 	size_t size;
 	spinlock_t lock;
 	unsigned long *bitmap;
 	unsigned long nr_pages;
 	void *vaddr;
-	struct page *page;
+	struct page **pages;
 };
 
 static struct dma_pool atomic_pool = {
-	.size = SZ_256K,
+	.size = DEFAULT_DMA_COHERENT_POOL_SIZE,
 };
 
 static int __init early_coherent_pool(char *p)
@@ -287,6 +289,21 @@
 }
 early_param("coherent_pool", early_coherent_pool);
 
+void __init init_dma_coherent_pool_size(unsigned long size)
+{
+	/*
+	 * Catch any attempt to set the pool size too late.
+	 */
+	BUG_ON(atomic_pool.vaddr);
+
+	/*
+	 * Set architecture specific coherent pool size only if
+	 * it has not been changed by kernel command line parameter.
+	 */
+	if (atomic_pool.size == DEFAULT_DMA_COHERENT_POOL_SIZE)
+		atomic_pool.size = size;
+}
+
 /*
  * Initialise the coherent pool for atomic allocations.
  */
@@ -297,6 +314,7 @@
 	unsigned long nr_pages = pool->size >> PAGE_SHIFT;
 	unsigned long *bitmap;
 	struct page *page;
+	struct page **pages;
 	void *ptr;
 	int bitmap_size = BITS_TO_LONGS(nr_pages) * sizeof(long);
 
@@ -304,21 +322,31 @@
 	if (!bitmap)
 		goto no_bitmap;
 
+	pages = kzalloc(nr_pages * sizeof(struct page *), GFP_KERNEL);
+	if (!pages)
+		goto no_pages;
+
 	if (IS_ENABLED(CONFIG_CMA))
 		ptr = __alloc_from_contiguous(NULL, pool->size, prot, &page);
 	else
 		ptr = __alloc_remap_buffer(NULL, pool->size, GFP_KERNEL, prot,
 					   &page, NULL);
 	if (ptr) {
+		int i;
+
+		for (i = 0; i < nr_pages; i++)
+			pages[i] = page + i;
+
 		spin_lock_init(&pool->lock);
 		pool->vaddr = ptr;
-		pool->page = page;
+		pool->pages = pages;
 		pool->bitmap = bitmap;
 		pool->nr_pages = nr_pages;
 		pr_info("DMA: preallocated %u KiB pool for atomic coherent allocations\n",
 		       (unsigned)pool->size / 1024);
 		return 0;
 	}
+no_pages:
 	kfree(bitmap);
 no_bitmap:
 	pr_err("DMA: failed to allocate %u KiB pool for atomic coherent allocation\n",
@@ -443,27 +471,45 @@
 	if (pageno < pool->nr_pages) {
 		bitmap_set(pool->bitmap, pageno, count);
 		ptr = pool->vaddr + PAGE_SIZE * pageno;
-		*ret_page = pool->page + pageno;
+		*ret_page = pool->pages[pageno];
+	} else {
+		pr_err_once("ERROR: %u KiB atomic DMA coherent pool is too small!\n"
+			    "Please increase it with coherent_pool= kernel parameter!\n",
+			    (unsigned)pool->size / 1024);
 	}
 	spin_unlock_irqrestore(&pool->lock, flags);
 
 	return ptr;
 }
 
+static bool __in_atomic_pool(void *start, size_t size)
+{
+	struct dma_pool *pool = &atomic_pool;
+	void *end = start + size;
+	void *pool_start = pool->vaddr;
+	void *pool_end = pool->vaddr + pool->size;
+
+	if (start < pool_start || start > pool_end)
+		return false;
+
+	if (end <= pool_end)
+		return true;
+
+	WARN(1, "Wrong coherent size(%p-%p) from atomic pool(%p-%p)\n",
+	     start, end - 1, pool_start, pool_end - 1);
+
+	return false;
+}
+
 static int __free_from_pool(void *start, size_t size)
 {
 	struct dma_pool *pool = &atomic_pool;
 	unsigned long pageno, count;
 	unsigned long flags;
 
-	if (start < pool->vaddr || start > pool->vaddr + pool->size)
+	if (!__in_atomic_pool(start, size))
 		return 0;
 
-	if (start + size > pool->vaddr + pool->size) {
-		WARN(1, "freeing wrong coherent size from pool\n");
-		return 0;
-	}
-
 	pageno = (start - pool->vaddr) >> PAGE_SHIFT;
 	count = size >> PAGE_SHIFT;
 
@@ -1090,10 +1136,22 @@
 	return 0;
 }
 
+static struct page **__atomic_get_pages(void *addr)
+{
+	struct dma_pool *pool = &atomic_pool;
+	struct page **pages = pool->pages;
+	int offs = (addr - pool->vaddr) >> PAGE_SHIFT;
+
+	return pages + offs;
+}
+
 static struct page **__iommu_get_pages(void *cpu_addr, struct dma_attrs *attrs)
 {
 	struct vm_struct *area;
 
+	if (__in_atomic_pool(cpu_addr, PAGE_SIZE))
+		return __atomic_get_pages(cpu_addr);
+
 	if (dma_get_attr(DMA_ATTR_NO_KERNEL_MAPPING, attrs))
 		return cpu_addr;
 
@@ -1103,6 +1161,34 @@
 	return NULL;
 }
 
+static void *__iommu_alloc_atomic(struct device *dev, size_t size,
+				  dma_addr_t *handle)
+{
+	struct page *page;
+	void *addr;
+
+	addr = __alloc_from_pool(size, &page);
+	if (!addr)
+		return NULL;
+
+	*handle = __iommu_create_mapping(dev, &page, size);
+	if (*handle == DMA_ERROR_CODE)
+		goto err_mapping;
+
+	return addr;
+
+err_mapping:
+	__free_from_pool(addr, size);
+	return NULL;
+}
+
+static void __iommu_free_atomic(struct device *dev, struct page **pages,
+				dma_addr_t handle, size_t size)
+{
+	__iommu_remove_mapping(dev, handle, size);
+	__free_from_pool(page_address(pages[0]), size);
+}
+
 static void *arm_iommu_alloc_attrs(struct device *dev, size_t size,
 	    dma_addr_t *handle, gfp_t gfp, struct dma_attrs *attrs)
 {
@@ -1113,6 +1199,9 @@
 	*handle = DMA_ERROR_CODE;
 	size = PAGE_ALIGN(size);
 
+	if (gfp & GFP_ATOMIC)
+		return __iommu_alloc_atomic(dev, size, handle);
+
 	pages = __iommu_alloc_buffer(dev, size, gfp);
 	if (!pages)
 		return NULL;
@@ -1179,6 +1268,11 @@
 		return;
 	}
 
+	if (__in_atomic_pool(cpu_addr, size)) {
+		__iommu_free_atomic(dev, pages, handle, size);
+		return;
+	}
+
 	if (!dma_get_attr(DMA_ATTR_NO_KERNEL_MAPPING, attrs)) {
 		unmap_kernel_range((unsigned long)cpu_addr, size);
 		vunmap(cpu_addr);
diff --git a/arch/arm/plat-omap/common.c b/arch/arm/plat-omap/common.c
index 89a3723..e5778ed 100644
--- a/arch/arm/plat-omap/common.c
+++ b/arch/arm/plat-omap/common.c
@@ -17,52 +17,12 @@
 #include <linux/dma-mapping.h>
 
 #include <plat/common.h>
-#include <plat/board.h>
 #include <plat/vram.h>
 #include <plat/dsp.h>
 #include <plat/dma.h>
 
 #include <plat/omap-secure.h>
 
-
-#define NO_LENGTH_CHECK 0xffffffff
-
-struct omap_board_config_kernel *omap_board_config __initdata;
-int omap_board_config_size;
-
-static const void *__init get_config(u16 tag, size_t len,
-		int skip, size_t *len_out)
-{
-	struct omap_board_config_kernel *kinfo = NULL;
-	int i;
-
-	/* Try to find the config from the board-specific structures
-	 * in the kernel. */
-	for (i = 0; i < omap_board_config_size; i++) {
-		if (omap_board_config[i].tag == tag) {
-			if (skip == 0) {
-				kinfo = &omap_board_config[i];
-				break;
-			} else {
-				skip--;
-			}
-		}
-	}
-	if (kinfo == NULL)
-		return NULL;
-	return kinfo->data;
-}
-
-const void *__init __omap_get_config(u16 tag, size_t len, int nr)
-{
-        return get_config(tag, len, nr, NULL);
-}
-
-const void *__init omap_get_var_config(u16 tag, size_t *len)
-{
-        return get_config(tag, NO_LENGTH_CHECK, 0, len);
-}
-
 void __init omap_reserve(void)
 {
 	omap_vram_reserve_sdram_memblock();
diff --git a/arch/arm/plat-omap/counter_32k.c b/arch/arm/plat-omap/counter_32k.c
index dbf1e03..902d2ff 100644
--- a/arch/arm/plat-omap/counter_32k.c
+++ b/arch/arm/plat-omap/counter_32k.c
@@ -24,7 +24,6 @@
 
 #include <plat/hardware.h>
 #include <plat/common.h>
-#include <plat/board.h>
 
 #include <plat/clock.h>
 
diff --git a/arch/arm/plat-omap/debug-devices.c b/arch/arm/plat-omap/debug-devices.c
index caa1f7b..c7a4c09 100644
--- a/arch/arm/plat-omap/debug-devices.c
+++ b/arch/arm/plat-omap/debug-devices.c
@@ -17,9 +17,6 @@
 
 #include <mach/hardware.h>
 
-#include <plat/board.h>
-
-
 /* Many OMAP development platforms reuse the same "debug board"; these
  * platforms include H2, H3, H4, and Perseus2.
  */
diff --git a/arch/arm/plat-omap/devices.c b/arch/arm/plat-omap/devices.c
index 1cba927..287ac37 100644
--- a/arch/arm/plat-omap/devices.c
+++ b/arch/arm/plat-omap/devices.c
@@ -23,7 +23,6 @@
 #include <asm/memblock.h>
 
 #include <plat/tc.h>
-#include <plat/board.h>
 #include <plat/mmc.h>
 #include <plat/menelaus.h>
 #include <plat/omap44xx.h>
diff --git a/arch/arm/plat-omap/dmtimer.c b/arch/arm/plat-omap/dmtimer.c
index 626ad8c..938b50a 100644
--- a/arch/arm/plat-omap/dmtimer.c
+++ b/arch/arm/plat-omap/dmtimer.c
@@ -189,6 +189,7 @@
 		timer->reserved = 1;
 		break;
 	}
+	spin_unlock_irqrestore(&dm_timer_lock, flags);
 
 	if (timer) {
 		ret = omap_dm_timer_prepare(timer);
@@ -197,7 +198,6 @@
 			timer = NULL;
 		}
 	}
-	spin_unlock_irqrestore(&dm_timer_lock, flags);
 
 	if (!timer)
 		pr_debug("%s: timer request failed!\n", __func__);
@@ -220,6 +220,7 @@
 			break;
 		}
 	}
+	spin_unlock_irqrestore(&dm_timer_lock, flags);
 
 	if (timer) {
 		ret = omap_dm_timer_prepare(timer);
@@ -228,7 +229,6 @@
 			timer = NULL;
 		}
 	}
-	spin_unlock_irqrestore(&dm_timer_lock, flags);
 
 	if (!timer)
 		pr_debug("%s: timer%d request failed!\n", __func__, id);
@@ -258,7 +258,7 @@
 
 void omap_dm_timer_disable(struct omap_dm_timer *timer)
 {
-	pm_runtime_put(&timer->pdev->dev);
+	pm_runtime_put_sync(&timer->pdev->dev);
 }
 EXPORT_SYMBOL_GPL(omap_dm_timer_disable);
 
diff --git a/arch/arm/plat-omap/fb.c b/arch/arm/plat-omap/fb.c
index dd6f92c..bcbb9d5 100644
--- a/arch/arm/plat-omap/fb.c
+++ b/arch/arm/plat-omap/fb.c
@@ -33,8 +33,6 @@
 #include <mach/hardware.h>
 #include <asm/mach/map.h>
 
-#include <plat/board.h>
-
 #if defined(CONFIG_FB_OMAP) || defined(CONFIG_FB_OMAP_MODULE)
 
 static bool omapfb_lcd_configured;
diff --git a/arch/arm/plat-omap/include/plat/board.h b/arch/arm/plat-omap/include/plat/board.h
deleted file mode 100644
index e62f20a..0000000
--- a/arch/arm/plat-omap/include/plat/board.h
+++ /dev/null
@@ -1,138 +0,0 @@
-/*
- *  arch/arm/plat-omap/include/mach/board.h
- *
- *  Information structures for board-specific data
- *
- *  Copyright (C) 2004	Nokia Corporation
- *  Written by Juha Yrjölä <juha.yrjola@nokia.com>
- */
-
-#ifndef _OMAP_BOARD_H
-#define _OMAP_BOARD_H
-
-#include <linux/types.h>
-
-#include <plat/gpio-switch.h>
-
-/*
- * OMAP35x EVM revision
- * Run time detection of EVM revision is done by reading Ethernet
- * PHY ID -
- *	GEN_1	= 0x01150000
- *	GEN_2	= 0x92200000
- */
-enum {
-	OMAP3EVM_BOARD_GEN_1 = 0,	/* EVM Rev between  A - D */
-	OMAP3EVM_BOARD_GEN_2,		/* EVM Rev >= Rev E */
-};
-
-/* Different peripheral ids */
-#define OMAP_TAG_CLOCK		0x4f01
-#define OMAP_TAG_GPIO_SWITCH	0x4f06
-#define OMAP_TAG_STI_CONSOLE	0x4f09
-#define OMAP_TAG_CAMERA_SENSOR	0x4f0a
-
-#define OMAP_TAG_BOOT_REASON    0x4f80
-#define OMAP_TAG_FLASH_PART	0x4f81
-#define OMAP_TAG_VERSION_STR	0x4f82
-
-struct omap_clock_config {
-	/* 0 for 12 MHz, 1 for 13 MHz and 2 for 19.2 MHz */
-	u8 system_clock_type;
-};
-
-struct omap_serial_console_config {
-	u8 console_uart;
-	u32 console_speed;
-};
-
-struct omap_sti_console_config {
-	unsigned enable:1;
-	u8 channel;
-};
-
-struct omap_camera_sensor_config {
-	u16 reset_gpio;
-	int (*power_on)(void * data);
-	int (*power_off)(void * data);
-};
-
-struct omap_lcd_config {
-	char panel_name[16];
-	char ctrl_name[16];
-	s16  nreset_gpio;
-	u8   data_lines;
-};
-
-struct device;
-struct fb_info;
-struct omap_backlight_config {
-	int default_intensity;
-	int (*set_power)(struct device *dev, int state);
-};
-
-struct omap_fbmem_config {
-	u32 start;
-	u32 size;
-};
-
-struct omap_pwm_led_platform_data {
-	const char *name;
-	int intensity_timer;
-	int blink_timer;
-	void (*set_power)(struct omap_pwm_led_platform_data *self, int on_off);
-};
-
-struct omap_uart_config {
-	/* Bit field of UARTs present; bit 0 --> UART1 */
-	unsigned int enabled_uarts;
-};
-
-
-struct omap_flash_part_config {
-	char part_table[0];
-};
-
-struct omap_boot_reason_config {
-	char reason_str[12];
-};
-
-struct omap_version_config {
-	char component[12];
-	char version[12];
-};
-
-struct omap_board_config_entry {
-	u16 tag;
-	u16 len;
-	u8  data[0];
-};
-
-struct omap_board_config_kernel {
-	u16 tag;
-	const void *data;
-};
-
-extern const void *__init __omap_get_config(u16 tag, size_t len, int nr);
-
-#define omap_get_config(tag, type) \
-	((const type *) __omap_get_config((tag), sizeof(type), 0))
-#define omap_get_nr_config(tag, type, nr) \
-	((const type *) __omap_get_config((tag), sizeof(type), (nr)))
-
-extern const void *__init omap_get_var_config(u16 tag, size_t *len);
-
-extern struct omap_board_config_kernel *omap_board_config;
-extern int omap_board_config_size;
-
-
-/* for TI reference platforms sharing the same debug card */
-extern int debug_card_init(u32 addr, unsigned gpio);
-
-/* OMAP3EVM revision */
-#if defined(CONFIG_MACH_OMAP3EVM)
-u8 get_omap3_evm_rev(void);
-#else
-#define get_omap3_evm_rev() (-EINVAL)
-#endif
-#endif
diff --git a/arch/arm/plat-omap/include/plat/cpu.h b/arch/arm/plat-omap/include/plat/cpu.h
index 68b180e..bb5d08a 100644
--- a/arch/arm/plat-omap/include/plat/cpu.h
+++ b/arch/arm/plat-omap/include/plat/cpu.h
@@ -372,7 +372,8 @@
 #define cpu_class_is_omap1()	(cpu_is_omap7xx() || cpu_is_omap15xx() || \
 				cpu_is_omap16xx())
 #define cpu_class_is_omap2()	(cpu_is_omap24xx() || cpu_is_omap34xx() || \
-				cpu_is_omap44xx() || soc_is_omap54xx())
+				cpu_is_omap44xx() || soc_is_omap54xx() || \
+				soc_is_am33xx())
 
 /* Various silicon revisions for omap2 */
 #define OMAP242X_CLASS		0x24200024
diff --git a/arch/arm/plat-omap/include/plat/debug-devices.h b/arch/arm/plat-omap/include/plat/debug-devices.h
new file mode 100644
index 0000000..a4edbd2
--- /dev/null
+++ b/arch/arm/plat-omap/include/plat/debug-devices.h
@@ -0,0 +1,9 @@
+#ifndef _OMAP_DEBUG_DEVICES_H
+#define _OMAP_DEBUG_DEVICES_H
+
+#include <linux/types.h>
+
+/* for TI reference platforms sharing the same debug card */
+extern int debug_card_init(u32 addr, unsigned gpio);
+
+#endif
diff --git a/arch/arm/plat-omap/include/plat/mmc.h b/arch/arm/plat-omap/include/plat/mmc.h
index eb3e4d5..8b4e4f2 100644
--- a/arch/arm/plat-omap/include/plat/mmc.h
+++ b/arch/arm/plat-omap/include/plat/mmc.h
@@ -15,7 +15,6 @@
 #include <linux/device.h>
 #include <linux/mmc/host.h>
 
-#include <plat/board.h>
 #include <plat/omap_hwmod.h>
 
 #define OMAP15XX_NR_MMC		1
diff --git a/arch/arm/plat-omap/include/plat/multi.h b/arch/arm/plat-omap/include/plat/multi.h
index 045e320..324d31b 100644
--- a/arch/arm/plat-omap/include/plat/multi.h
+++ b/arch/arm/plat-omap/include/plat/multi.h
@@ -108,4 +108,13 @@
 # endif
 #endif
 
+#ifdef CONFIG_SOC_AM33XX
+# ifdef OMAP_NAME
+#  undef  MULTI_OMAP2
+#  define MULTI_OMAP2
+# else
+#  define OMAP_NAME am33xx
+# endif
+#endif
+
 #endif	/* __PLAT_OMAP_MULTI_H */
diff --git a/arch/arm/plat-omap/include/plat/omap-serial.h b/arch/arm/plat-omap/include/plat/omap-serial.h
index 1a52725..a531149 100644
--- a/arch/arm/plat-omap/include/plat/omap-serial.h
+++ b/arch/arm/plat-omap/include/plat/omap-serial.h
@@ -18,7 +18,7 @@
 #define __OMAP_SERIAL_H__
 
 #include <linux/serial_core.h>
-#include <linux/platform_device.h>
+#include <linux/device.h>
 #include <linux/pm_qos.h>
 
 #include <plat/mux.h>
@@ -42,10 +42,10 @@
 #define OMAP_UART_WER_MOD_WKUP	0X7F
 
 /* Enable XON/XOFF flow control on output */
-#define OMAP_UART_SW_TX		0x04
+#define OMAP_UART_SW_TX		0x8
 
 /* Enable XON/XOFF flow control on input */
-#define OMAP_UART_SW_RX		0x04
+#define OMAP_UART_SW_RX		0x2
 
 #define OMAP_UART_SYSC_RESET	0X07
 #define OMAP_UART_TCR_TRIG	0X0F
@@ -69,11 +69,14 @@
 	unsigned int		dma_rx_timeout;
 	unsigned int		autosuspend_timeout;
 	unsigned int		dma_rx_poll_rate;
+	int			DTR_gpio;
+	int			DTR_inverted;
+	int			DTR_present;
 
 	int (*get_context_loss_count)(struct device *);
-	void (*set_forceidle)(struct platform_device *);
-	void (*set_noidle)(struct platform_device *);
-	void (*enable_wakeup)(struct platform_device *, bool);
+	void (*set_forceidle)(struct device *);
+	void (*set_noidle)(struct device *);
+	void (*enable_wakeup)(struct device *, bool);
 };
 
 struct uart_omap_dma {
@@ -102,39 +105,4 @@
 	unsigned int		rx_timeout;
 };
 
-struct uart_omap_port {
-	struct uart_port	port;
-	struct uart_omap_dma	uart_dma;
-	struct platform_device	*pdev;
-
-	unsigned char		ier;
-	unsigned char		lcr;
-	unsigned char		mcr;
-	unsigned char		fcr;
-	unsigned char		efr;
-	unsigned char		dll;
-	unsigned char		dlh;
-	unsigned char		mdr1;
-	unsigned char		scr;
-
-	int			use_dma;
-	/*
-	 * Some bits in registers are cleared on a read, so they must
-	 * be saved whenever the register is read but the bits will not
-	 * be immediately processed.
-	 */
-	unsigned int		lsr_break_flag;
-	unsigned char		msr_saved_flags;
-	char			name[20];
-	unsigned long		port_activity;
-	u32			context_loss_cnt;
-	u32			errata;
-	u8			wakeups_enabled;
-
-	struct pm_qos_request	pm_qos_request;
-	u32			latency;
-	u32			calc_latency;
-	struct work_struct	qos_work;
-};
-
 #endif /* __OMAP_SERIAL_H__ */
diff --git a/arch/arm/plat-omap/include/plat/uncompress.h b/arch/arm/plat-omap/include/plat/uncompress.h
index b8d19a1..7f7b112 100644
--- a/arch/arm/plat-omap/include/plat/uncompress.h
+++ b/arch/arm/plat-omap/include/plat/uncompress.h
@@ -110,7 +110,7 @@
 	_DEBUG_LL_ENTRY(mach, AM33XX_UART##p##_BASE, OMAP_PORT_SHIFT,	\
 		AM33XXUART##p)
 
-static inline void __arch_decomp_setup(unsigned long arch_id)
+static inline void arch_decomp_setup(void)
 {
 	int port = 0;
 
@@ -198,8 +198,6 @@
 	} while (0);
 }
 
-#define arch_decomp_setup()	__arch_decomp_setup(arch_id)
-
 /*
  * nothing to do
  */
diff --git a/arch/arm/plat-omap/include/plat/usb.h b/arch/arm/plat-omap/include/plat/usb.h
index 548a4c8..bd20588 100644
--- a/arch/arm/plat-omap/include/plat/usb.h
+++ b/arch/arm/plat-omap/include/plat/usb.h
@@ -5,7 +5,6 @@
 
 #include <linux/io.h>
 #include <linux/usb/musb.h>
-#include <plat/board.h>
 
 #define OMAP3_HS_USB_PORTS	3
 
diff --git a/arch/arm/plat-omap/sram.c b/arch/arm/plat-omap/sram.c
index 766181c..d861aa7 100644
--- a/arch/arm/plat-omap/sram.c
+++ b/arch/arm/plat-omap/sram.c
@@ -26,7 +26,6 @@
 #include <asm/mach/map.h>
 
 #include <plat/sram.h>
-#include <plat/board.h>
 #include <plat/cpu.h>
 
 #include "sram.h"
diff --git a/arch/arm/plat-orion/common.c b/arch/arm/plat-orion/common.c
index d245a87..b8b747a 100644
--- a/arch/arm/plat-orion/common.c
+++ b/arch/arm/plat-orion/common.c
@@ -291,10 +291,12 @@
 void __init orion_ge00_init(struct mv643xx_eth_platform_data *eth_data,
 			    unsigned long mapbase,
 			    unsigned long irq,
-			    unsigned long irq_err)
+			    unsigned long irq_err,
+			    unsigned int tx_csum_limit)
 {
 	fill_resources(&orion_ge00_shared, orion_ge00_shared_resources,
 		       mapbase + 0x2000, SZ_16K - 1, irq_err);
+	orion_ge00_shared_data.tx_csum_limit = tx_csum_limit;
 	ge_complete(&orion_ge00_shared_data,
 		    orion_ge00_resources, irq, &orion_ge00_shared,
 		    eth_data, &orion_ge00);
@@ -343,10 +345,12 @@
 void __init orion_ge01_init(struct mv643xx_eth_platform_data *eth_data,
 			    unsigned long mapbase,
 			    unsigned long irq,
-			    unsigned long irq_err)
+			    unsigned long irq_err,
+			    unsigned int tx_csum_limit)
 {
 	fill_resources(&orion_ge01_shared, orion_ge01_shared_resources,
 		       mapbase + 0x2000, SZ_16K - 1, irq_err);
+	orion_ge01_shared_data.tx_csum_limit = tx_csum_limit;
 	ge_complete(&orion_ge01_shared_data,
 		    orion_ge01_resources, irq, &orion_ge01_shared,
 		    eth_data, &orion_ge01);
diff --git a/arch/arm/plat-orion/include/plat/common.h b/arch/arm/plat-orion/include/plat/common.h
index e00fdb2..ae2377e 100644
--- a/arch/arm/plat-orion/include/plat/common.h
+++ b/arch/arm/plat-orion/include/plat/common.h
@@ -39,12 +39,14 @@
 void __init orion_ge00_init(struct mv643xx_eth_platform_data *eth_data,
 			    unsigned long mapbase,
 			    unsigned long irq,
-			    unsigned long irq_err);
+			    unsigned long irq_err,
+			    unsigned int tx_csum_limit);
 
 void __init orion_ge01_init(struct mv643xx_eth_platform_data *eth_data,
 			    unsigned long mapbase,
 			    unsigned long irq,
-			    unsigned long irq_err);
+			    unsigned long irq_err,
+			    unsigned int tx_csum_limit);
 
 void __init orion_ge10_init(struct mv643xx_eth_platform_data *eth_data,
 			    unsigned long mapbase,
diff --git a/arch/arm/plat-s3c24xx/dma.c b/arch/arm/plat-s3c24xx/dma.c
index 28f898f..db98e70 100644
--- a/arch/arm/plat-s3c24xx/dma.c
+++ b/arch/arm/plat-s3c24xx/dma.c
@@ -430,7 +430,7 @@
  * when necessary.
 */
 
-int s3c2410_dma_enqueue(unsigned int channel, void *id,
+int s3c2410_dma_enqueue(enum dma_ch channel, void *id,
 			dma_addr_t data, int size)
 {
 	struct s3c2410_dma_chan *chan = s3c_dma_lookup_channel(channel);
diff --git a/arch/arm/plat-samsung/devs.c b/arch/arm/plat-samsung/devs.c
index 74e31ce..fc49f3d 100644
--- a/arch/arm/plat-samsung/devs.c
+++ b/arch/arm/plat-samsung/devs.c
@@ -32,6 +32,8 @@
 #include <linux/platform_data/s3c-hsudc.h>
 #include <linux/platform_data/s3c-hsotg.h>
 
+#include <media/s5p_hdmi.h>
+
 #include <asm/irq.h>
 #include <asm/pmu.h>
 #include <asm/mach/arch.h>
@@ -748,7 +750,8 @@
 	if (!pd) {
 		pd = &default_i2c_data;
 
-		if (soc_is_exynos4210())
+		if (soc_is_exynos4210() ||
+		    soc_is_exynos4212() || soc_is_exynos4412())
 			pd->bus_num = 8;
 		else if (soc_is_s5pv210())
 			pd->bus_num = 3;
@@ -759,6 +762,30 @@
 	npd = s3c_set_platdata(pd, sizeof(struct s3c2410_platform_i2c),
 			       &s5p_device_i2c_hdmiphy);
 }
+
+struct s5p_hdmi_platform_data s5p_hdmi_def_platdata;
+
+void __init s5p_hdmi_set_platdata(struct i2c_board_info *hdmiphy_info,
+				  struct i2c_board_info *mhl_info, int mhl_bus)
+{
+	struct s5p_hdmi_platform_data *pd = &s5p_hdmi_def_platdata;
+
+	if (soc_is_exynos4210() ||
+	    soc_is_exynos4212() || soc_is_exynos4412())
+		pd->hdmiphy_bus = 8;
+	else if (soc_is_s5pv210())
+		pd->hdmiphy_bus = 3;
+	else
+		pd->hdmiphy_bus = 0;
+
+	pd->hdmiphy_info = hdmiphy_info;
+	pd->mhl_info = mhl_info;
+	pd->mhl_bus = mhl_bus;
+
+	s3c_set_platdata(pd, sizeof(struct s5p_hdmi_platform_data),
+			 &s5p_device_hdmi);
+}
+
 #endif /* CONFIG_S5P_DEV_I2C_HDMIPHY */
 
 /* I2S */
diff --git a/arch/arm/plat-samsung/include/plat/hdmi.h b/arch/arm/plat-samsung/include/plat/hdmi.h
new file mode 100644
index 0000000..331d046
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/hdmi.h
@@ -0,0 +1,16 @@
+/*
+ * Copyright (C) 2012 Samsung Electronics Co.Ltd
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#ifndef __PLAT_SAMSUNG_HDMI_H
+#define __PLAT_SAMSUNG_HDMI_H __FILE__
+
+extern void s5p_hdmi_set_platdata(struct i2c_board_info *hdmiphy_info,
+				  struct i2c_board_info *mhl_info, int mhl_bus);
+
+#endif /* __PLAT_SAMSUNG_HDMI_H */
diff --git a/arch/arm/plat-samsung/pm.c b/arch/arm/plat-samsung/pm.c
index 64ab65f..1507028 100644
--- a/arch/arm/plat-samsung/pm.c
+++ b/arch/arm/plat-samsung/pm.c
@@ -74,7 +74,7 @@
 
 #ifdef CONFIG_SAMSUNG_PM_DEBUG
 
-struct pm_uart_save uart_save[CONFIG_SERIAL_SAMSUNG_UARTS];
+static struct pm_uart_save uart_save[CONFIG_SERIAL_SAMSUNG_UARTS];
 
 static void s3c_pm_save_uart(unsigned int uart, struct pm_uart_save *save)
 {
diff --git a/arch/ia64/hp/sim/simserial.c b/arch/ia64/hp/sim/simserial.c
index c34785d..ec536e4 100644
--- a/arch/ia64/hp/sim/simserial.c
+++ b/arch/ia64/hp/sim/simserial.c
@@ -338,7 +338,7 @@
 {
 	/* Handle turning off CRTSCTS */
 	if ((old_termios->c_cflag & CRTSCTS) &&
-	    !(tty->termios->c_cflag & CRTSCTS)) {
+	    !(tty->termios.c_cflag & CRTSCTS)) {
 		tty->hw_stopped = 0;
 	}
 }
@@ -545,6 +545,7 @@
 	/* the port is imaginary */
 	printk(KERN_INFO "ttyS0 at 0x03f8 (irq = %d) is a 16550\n", state->irq);
 
+	tty_port_link_device(&state->port, hp_simserial_driver, 0);
 	retval = tty_register_driver(hp_simserial_driver);
 	if (retval) {
 		printk(KERN_ERR "Couldn't register simserial driver\n");
diff --git a/arch/m68k/emu/nfcon.c b/arch/m68k/emu/nfcon.c
index 8db25e8..16d170f 100644
--- a/arch/m68k/emu/nfcon.c
+++ b/arch/m68k/emu/nfcon.c
@@ -19,6 +19,7 @@
 #include <asm/natfeat.h>
 
 static int stderr_id;
+static struct tty_port nfcon_tty_port;
 static struct tty_driver *nfcon_tty_driver;
 
 static void nfputs(const char *str, unsigned int count)
@@ -119,6 +120,8 @@
 {
 	int res;
 
+	tty_port_init(&nfcon_tty_port);
+
 	stderr_id = nf_get_id("NF_STDERR");
 	if (!stderr_id)
 		return -ENODEV;
@@ -135,6 +138,7 @@
 	nfcon_tty_driver->flags = TTY_DRIVER_REAL_RAW;
 
 	tty_set_operations(nfcon_tty_driver, &nfcon_tty_ops);
+	tty_port_link_device(&nfcon_tty_port, nfcon_tty_driver, 0);
 	res = tty_register_driver(nfcon_tty_driver);
 	if (res) {
 		pr_err("failed to register nfcon tty driver\n");
diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig
index 331d574..faf6528 100644
--- a/arch/mips/Kconfig
+++ b/arch/mips/Kconfig
@@ -89,6 +89,7 @@
 	select CEVT_R4K
 	select CSRC_R4K
 	select DMA_NONCOHERENT
+	select HAVE_CLK
 	select IRQ_CPU
 	select MIPS_MACHINE
 	select SYS_HAS_CPU_MIPS32_R2
diff --git a/arch/mips/alchemy/board-mtx1.c b/arch/mips/alchemy/board-mtx1.c
index 9996948..a124c25 100644
--- a/arch/mips/alchemy/board-mtx1.c
+++ b/arch/mips/alchemy/board-mtx1.c
@@ -228,6 +228,8 @@
 	 * adapter on the mtx-1 "singleboard" variant. It triggers a custom
 	 * logic chip connected to EXT_IO3 (GPIO1) to suppress IDSEL signals.
 	 */
+	udelay(1);
+
 	if (assert && devsel != 0)
 		/* Suppress signal to Cardbus */
 		alchemy_gpio_set_value(1, 0);	/* set EXT_IO3 OFF */
diff --git a/arch/mips/ath79/dev-usb.c b/arch/mips/ath79/dev-usb.c
index 36e9570..b2a2311 100644
--- a/arch/mips/ath79/dev-usb.c
+++ b/arch/mips/ath79/dev-usb.c
@@ -145,6 +145,8 @@
 
 	ath79_ohci_resources[0].start = AR7240_OHCI_BASE;
 	ath79_ohci_resources[0].end = AR7240_OHCI_BASE + AR7240_OHCI_SIZE - 1;
+	ath79_ohci_resources[1].start = ATH79_CPU_IRQ_USB;
+	ath79_ohci_resources[1].end = ATH79_CPU_IRQ_USB;
 	platform_device_register(&ath79_ohci_device);
 }
 
diff --git a/arch/mips/ath79/gpio.c b/arch/mips/ath79/gpio.c
index 29054f2..48fe762 100644
--- a/arch/mips/ath79/gpio.c
+++ b/arch/mips/ath79/gpio.c
@@ -188,8 +188,10 @@
 
 	if (soc_is_ar71xx())
 		ath79_gpio_count = AR71XX_GPIO_COUNT;
-	else if (soc_is_ar724x())
-		ath79_gpio_count = AR724X_GPIO_COUNT;
+	else if (soc_is_ar7240())
+		ath79_gpio_count = AR7240_GPIO_COUNT;
+	else if (soc_is_ar7241() || soc_is_ar7242())
+		ath79_gpio_count = AR7241_GPIO_COUNT;
 	else if (soc_is_ar913x())
 		ath79_gpio_count = AR913X_GPIO_COUNT;
 	else if (soc_is_ar933x())
diff --git a/arch/mips/bcm63xx/dev-spi.c b/arch/mips/bcm63xx/dev-spi.c
index e39f730..f1c9c3e 100644
--- a/arch/mips/bcm63xx/dev-spi.c
+++ b/arch/mips/bcm63xx/dev-spi.c
@@ -106,11 +106,15 @@
 	if (BCMCPU_IS_6338() || BCMCPU_IS_6348()) {
 		spi_resources[0].end += BCM_6338_RSET_SPI_SIZE - 1;
 		spi_pdata.fifo_size = SPI_6338_MSG_DATA_SIZE;
+		spi_pdata.msg_type_shift = SPI_6338_MSG_TYPE_SHIFT;
+		spi_pdata.msg_ctl_width = SPI_6338_MSG_CTL_WIDTH;
 	}
 
 	if (BCMCPU_IS_6358() || BCMCPU_IS_6368()) {
 		spi_resources[0].end += BCM_6358_RSET_SPI_SIZE - 1;
 		spi_pdata.fifo_size = SPI_6358_MSG_DATA_SIZE;
+		spi_pdata.msg_type_shift = SPI_6358_MSG_TYPE_SHIFT;
+		spi_pdata.msg_ctl_width = SPI_6358_MSG_CTL_WIDTH;
 	}
 
 	bcm63xx_spi_regs_init();
diff --git a/arch/mips/cavium-octeon/octeon-irq.c b/arch/mips/cavium-octeon/octeon-irq.c
index 7fb1f22..274cd4f 100644
--- a/arch/mips/cavium-octeon/octeon-irq.c
+++ b/arch/mips/cavium-octeon/octeon-irq.c
@@ -61,6 +61,12 @@
 	octeon_irq_ciu_to_irq[line][bit] = irq;
 }
 
+static void octeon_irq_force_ciu_mapping(struct irq_domain *domain,
+					 int irq, int line, int bit)
+{
+	irq_domain_associate(domain, irq, line << 6 | bit);
+}
+
 static int octeon_coreid_for_cpu(int cpu)
 {
 #ifdef CONFIG_SMP
@@ -183,19 +189,9 @@
 		mutex_init(&cd->core_irq_mutex);
 
 		irq = OCTEON_IRQ_SW0 + i;
-		switch (irq) {
-		case OCTEON_IRQ_TIMER:
-		case OCTEON_IRQ_SW0:
-		case OCTEON_IRQ_SW1:
-		case OCTEON_IRQ_5:
-		case OCTEON_IRQ_PERF:
-			irq_set_chip_data(irq, cd);
-			irq_set_chip_and_handler(irq, &octeon_irq_chip_core,
-						 handle_percpu_irq);
-			break;
-		default:
-			break;
-		}
+		irq_set_chip_data(irq, cd);
+		irq_set_chip_and_handler(irq, &octeon_irq_chip_core,
+					 handle_percpu_irq);
 	}
 }
 
@@ -890,7 +886,6 @@
 	unsigned int type;
 	unsigned int pin;
 	unsigned int trigger;
-	struct octeon_irq_gpio_domain_data *gpiod;
 
 	if (d->of_node != node)
 		return -EINVAL;
@@ -925,8 +920,7 @@
 		break;
 	}
 	*out_type = type;
-	gpiod = d->host_data;
-	*out_hwirq = gpiod->base_hwirq + pin;
+	*out_hwirq = pin;
 
 	return 0;
 }
@@ -996,19 +990,21 @@
 static int octeon_irq_gpio_map(struct irq_domain *d,
 			       unsigned int virq, irq_hw_number_t hw)
 {
-	unsigned int line = hw >> 6;
-	unsigned int bit = hw & 63;
+	struct octeon_irq_gpio_domain_data *gpiod = d->host_data;
+	unsigned int line, bit;
 
 	if (!octeon_irq_virq_in_range(virq))
 		return -EINVAL;
 
+	hw += gpiod->base_hwirq;
+	line = hw >> 6;
+	bit = hw & 63;
 	if (line > 1 || octeon_irq_ciu_to_irq[line][bit] != 0)
 		return -EINVAL;
 
 	octeon_irq_set_ciu_mapping(virq, line, bit,
 				   octeon_irq_gpio_chip,
 				   octeon_irq_handle_gpio);
-
 	return 0;
 }
 
@@ -1149,6 +1145,7 @@
 	struct irq_chip *chip_wd;
 	struct device_node *gpio_node;
 	struct device_node *ciu_node;
+	struct irq_domain *ciu_domain = NULL;
 
 	octeon_irq_init_ciu_percpu();
 	octeon_irq_setup_secondary = octeon_irq_setup_secondary_ciu;
@@ -1177,31 +1174,6 @@
 	/* Mips internal */
 	octeon_irq_init_core();
 
-	/* CIU_0 */
-	for (i = 0; i < 16; i++)
-		octeon_irq_set_ciu_mapping(i + OCTEON_IRQ_WORKQ0, 0, i + 0, chip, handle_level_irq);
-
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_MBOX0, 0, 32, chip_mbox, handle_percpu_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_MBOX1, 0, 33, chip_mbox, handle_percpu_irq);
-
-	for (i = 0; i < 4; i++)
-		octeon_irq_set_ciu_mapping(i + OCTEON_IRQ_PCI_INT0, 0, i + 36, chip, handle_level_irq);
-	for (i = 0; i < 4; i++)
-		octeon_irq_set_ciu_mapping(i + OCTEON_IRQ_PCI_MSI0, 0, i + 40, chip, handle_level_irq);
-
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_RML, 0, 46, chip, handle_level_irq);
-	for (i = 0; i < 4; i++)
-		octeon_irq_set_ciu_mapping(i + OCTEON_IRQ_TIMER0, 0, i + 52, chip, handle_edge_irq);
-
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_USB0, 0, 56, chip, handle_level_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_BOOTDMA, 0, 63, chip, handle_level_irq);
-
-	/* CIU_1 */
-	for (i = 0; i < 16; i++)
-		octeon_irq_set_ciu_mapping(i + OCTEON_IRQ_WDOG0, 1, i + 0, chip_wd, handle_level_irq);
-
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_USB1, 1, 17, chip, handle_level_irq);
-
 	gpio_node = of_find_compatible_node(NULL, NULL, "cavium,octeon-3860-gpio");
 	if (gpio_node) {
 		struct octeon_irq_gpio_domain_data *gpiod;
@@ -1219,10 +1191,35 @@
 
 	ciu_node = of_find_compatible_node(NULL, NULL, "cavium,octeon-3860-ciu");
 	if (ciu_node) {
-		irq_domain_add_tree(ciu_node, &octeon_irq_domain_ciu_ops, NULL);
+		ciu_domain = irq_domain_add_tree(ciu_node, &octeon_irq_domain_ciu_ops, NULL);
 		of_node_put(ciu_node);
 	} else
-		pr_warn("Cannot find device node for cavium,octeon-3860-ciu.\n");
+		panic("Cannot find device node for cavium,octeon-3860-ciu.");
+
+	/* CIU_0 */
+	for (i = 0; i < 16; i++)
+		octeon_irq_force_ciu_mapping(ciu_domain, i + OCTEON_IRQ_WORKQ0, 0, i + 0);
+
+	octeon_irq_set_ciu_mapping(OCTEON_IRQ_MBOX0, 0, 32, chip_mbox, handle_percpu_irq);
+	octeon_irq_set_ciu_mapping(OCTEON_IRQ_MBOX1, 0, 33, chip_mbox, handle_percpu_irq);
+
+	for (i = 0; i < 4; i++)
+		octeon_irq_force_ciu_mapping(ciu_domain, i + OCTEON_IRQ_PCI_INT0, 0, i + 36);
+	for (i = 0; i < 4; i++)
+		octeon_irq_force_ciu_mapping(ciu_domain, i + OCTEON_IRQ_PCI_MSI0, 0, i + 40);
+
+	octeon_irq_force_ciu_mapping(ciu_domain, OCTEON_IRQ_RML, 0, 46);
+	for (i = 0; i < 4; i++)
+		octeon_irq_force_ciu_mapping(ciu_domain, i + OCTEON_IRQ_TIMER0, 0, i + 52);
+
+	octeon_irq_force_ciu_mapping(ciu_domain, OCTEON_IRQ_USB0, 0, 56);
+	octeon_irq_force_ciu_mapping(ciu_domain, OCTEON_IRQ_BOOTDMA, 0, 63);
+
+	/* CIU_1 */
+	for (i = 0; i < 16; i++)
+		octeon_irq_set_ciu_mapping(i + OCTEON_IRQ_WDOG0, 1, i + 0, chip_wd, handle_level_irq);
+
+	octeon_irq_force_ciu_mapping(ciu_domain, OCTEON_IRQ_USB1, 1, 17);
 
 	/* Enable the CIU lines */
 	set_c0_status(STATUSF_IP3 | STATUSF_IP2);
diff --git a/arch/mips/cavium-octeon/serial.c b/arch/mips/cavium-octeon/serial.c
index 138b221..569f41b 100644
--- a/arch/mips/cavium-octeon/serial.c
+++ b/arch/mips/cavium-octeon/serial.c
@@ -47,40 +47,40 @@
 {
 	int irq, res;
 	struct resource *res_mem;
-	struct uart_port port;
+	struct uart_8250_port up;
 
 	/* All adaptors have an irq.  */
 	irq = platform_get_irq(pdev, 0);
 	if (irq < 0)
 		return irq;
 
-	memset(&port, 0, sizeof(port));
+	memset(&up, 0, sizeof(up));
 
-	port.flags = ASYNC_SKIP_TEST | UPF_SHARE_IRQ | UPF_FIXED_TYPE;
-	port.type = PORT_OCTEON;
-	port.iotype = UPIO_MEM;
-	port.regshift = 3;
-	port.dev = &pdev->dev;
+	up.port.flags = ASYNC_SKIP_TEST | UPF_SHARE_IRQ | UPF_FIXED_TYPE;
+	up.port.type = PORT_OCTEON;
+	up.port.iotype = UPIO_MEM;
+	up.port.regshift = 3;
+	up.port.dev = &pdev->dev;
 
 	if (octeon_is_simulation())
 		/* Make simulator output fast*/
-		port.uartclk = 115200 * 16;
+		up.port.uartclk = 115200 * 16;
 	else
-		port.uartclk = octeon_get_io_clock_rate();
+		up.port.uartclk = octeon_get_io_clock_rate();
 
-	port.serial_in = octeon_serial_in;
-	port.serial_out = octeon_serial_out;
-	port.irq = irq;
+	up.port.serial_in = octeon_serial_in;
+	up.port.serial_out = octeon_serial_out;
+	up.port.irq = irq;
 
 	res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	if (res_mem == NULL) {
 		dev_err(&pdev->dev, "found no memory resource\n");
 		return -ENXIO;
 	}
-	port.mapbase = res_mem->start;
-	port.membase = ioremap(res_mem->start, resource_size(res_mem));
+	up.port.mapbase = res_mem->start;
+	up.port.membase = ioremap(res_mem->start, resource_size(res_mem));
 
-	res = serial8250_register_port(&port);
+	res = serial8250_register_8250_port(&up);
 
 	return res >= 0 ? 0 : res;
 }
diff --git a/arch/mips/include/asm/mach-ath79/ar71xx_regs.h b/arch/mips/include/asm/mach-ath79/ar71xx_regs.h
index 1caa78a..dde5044 100644
--- a/arch/mips/include/asm/mach-ath79/ar71xx_regs.h
+++ b/arch/mips/include/asm/mach-ath79/ar71xx_regs.h
@@ -393,7 +393,8 @@
 #define AR71XX_GPIO_REG_FUNC		0x28
 
 #define AR71XX_GPIO_COUNT		16
-#define AR724X_GPIO_COUNT		18
+#define AR7240_GPIO_COUNT		18
+#define AR7241_GPIO_COUNT		20
 #define AR913X_GPIO_COUNT		22
 #define AR933X_GPIO_COUNT		30
 #define AR934X_GPIO_COUNT		23
diff --git a/arch/mips/include/asm/mach-ath79/cpu-feature-overrides.h b/arch/mips/include/asm/mach-ath79/cpu-feature-overrides.h
index 4476fa0..6ddae92 100644
--- a/arch/mips/include/asm/mach-ath79/cpu-feature-overrides.h
+++ b/arch/mips/include/asm/mach-ath79/cpu-feature-overrides.h
@@ -42,7 +42,6 @@
 #define cpu_has_mips64r1	0
 #define cpu_has_mips64r2	0
 
-#define cpu_has_dsp		0
 #define cpu_has_mipsmt		0
 
 #define cpu_has_64bits		0
diff --git a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h
index 7d98dbe..c9bae13 100644
--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h
@@ -9,6 +9,8 @@
 
 struct bcm63xx_spi_pdata {
 	unsigned int	fifo_size;
+	unsigned int	msg_type_shift;
+	unsigned int	msg_ctl_width;
 	int		bus_num;
 	int		num_chipselect;
 	u32		speed_hz;
diff --git a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
index 4ccc2a7..61f2a2a 100644
--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
@@ -1054,7 +1054,8 @@
 #define SPI_6338_FILL_BYTE		0x07
 #define SPI_6338_MSG_TAIL		0x09
 #define SPI_6338_RX_TAIL		0x0b
-#define SPI_6338_MSG_CTL		0x40
+#define SPI_6338_MSG_CTL		0x40	/* 8-bits register */
+#define SPI_6338_MSG_CTL_WIDTH		8
 #define SPI_6338_MSG_DATA		0x41
 #define SPI_6338_MSG_DATA_SIZE		0x3f
 #define SPI_6338_RX_DATA		0x80
@@ -1070,7 +1071,8 @@
 #define SPI_6348_FILL_BYTE		0x07
 #define SPI_6348_MSG_TAIL		0x09
 #define SPI_6348_RX_TAIL		0x0b
-#define SPI_6348_MSG_CTL		0x40
+#define SPI_6348_MSG_CTL		0x40	/* 8-bits register */
+#define SPI_6348_MSG_CTL_WIDTH		8
 #define SPI_6348_MSG_DATA		0x41
 #define SPI_6348_MSG_DATA_SIZE		0x3f
 #define SPI_6348_RX_DATA		0x80
@@ -1078,6 +1080,7 @@
 
 /* BCM 6358 SPI core */
 #define SPI_6358_MSG_CTL		0x00	/* 16-bits register */
+#define SPI_6358_MSG_CTL_WIDTH		16
 #define SPI_6358_MSG_DATA		0x02
 #define SPI_6358_MSG_DATA_SIZE		0x21e
 #define SPI_6358_RX_DATA		0x400
@@ -1094,6 +1097,7 @@
 
 /* BCM 6358 SPI core */
 #define SPI_6368_MSG_CTL		0x00	/* 16-bits register */
+#define SPI_6368_MSG_CTL_WIDTH		16
 #define SPI_6368_MSG_DATA		0x02
 #define SPI_6368_MSG_DATA_SIZE		0x21e
 #define SPI_6368_RX_DATA		0x400
@@ -1115,7 +1119,10 @@
 #define SPI_HD_W			0x01
 #define SPI_HD_R			0x02
 #define SPI_BYTE_CNT_SHIFT		0
-#define SPI_MSG_TYPE_SHIFT		14
+#define SPI_6338_MSG_TYPE_SHIFT		6
+#define SPI_6348_MSG_TYPE_SHIFT		6
+#define SPI_6358_MSG_TYPE_SHIFT		14
+#define SPI_6368_MSG_TYPE_SHIFT		14
 
 /* Command */
 #define SPI_CMD_NOOP			0x00
diff --git a/arch/mips/include/asm/mach-cavium-octeon/irq.h b/arch/mips/include/asm/mach-cavium-octeon/irq.h
index 4189920..c22a307 100644
--- a/arch/mips/include/asm/mach-cavium-octeon/irq.h
+++ b/arch/mips/include/asm/mach-cavium-octeon/irq.h
@@ -21,14 +21,10 @@
 	OCTEON_IRQ_TIMER,
 /* sources in CIU_INTX_EN0 */
 	OCTEON_IRQ_WORKQ0,
-	OCTEON_IRQ_GPIO0 = OCTEON_IRQ_WORKQ0 + 16,
-	OCTEON_IRQ_WDOG0 = OCTEON_IRQ_GPIO0 + 16,
+	OCTEON_IRQ_WDOG0 = OCTEON_IRQ_WORKQ0 + 16,
 	OCTEON_IRQ_WDOG15 = OCTEON_IRQ_WDOG0 + 15,
 	OCTEON_IRQ_MBOX0 = OCTEON_IRQ_WDOG0 + 16,
 	OCTEON_IRQ_MBOX1,
-	OCTEON_IRQ_UART0,
-	OCTEON_IRQ_UART1,
-	OCTEON_IRQ_UART2,
 	OCTEON_IRQ_PCI_INT0,
 	OCTEON_IRQ_PCI_INT1,
 	OCTEON_IRQ_PCI_INT2,
@@ -38,8 +34,6 @@
 	OCTEON_IRQ_PCI_MSI2,
 	OCTEON_IRQ_PCI_MSI3,
 
-	OCTEON_IRQ_TWSI,
-	OCTEON_IRQ_TWSI2,
 	OCTEON_IRQ_RML,
 	OCTEON_IRQ_TIMER0,
 	OCTEON_IRQ_TIMER1,
@@ -47,8 +41,6 @@
 	OCTEON_IRQ_TIMER3,
 	OCTEON_IRQ_USB0,
 	OCTEON_IRQ_USB1,
-	OCTEON_IRQ_MII0,
-	OCTEON_IRQ_MII1,
 	OCTEON_IRQ_BOOTDMA,
 #ifndef CONFIG_PCI_MSI
 	OCTEON_IRQ_LAST = 127
diff --git a/arch/mips/include/asm/module.h b/arch/mips/include/asm/module.h
index 7531ecd..dca8bce 100644
--- a/arch/mips/include/asm/module.h
+++ b/arch/mips/include/asm/module.h
@@ -10,6 +10,7 @@
 	struct list_head dbe_list;
 	const struct exception_table_entry *dbe_start;
 	const struct exception_table_entry *dbe_end;
+	struct mips_hi16 *r_mips_hi16_list;
 };
 
 typedef uint8_t Elf64_Byte;		/* Type for a 8-bit quantity.  */
diff --git a/arch/mips/include/asm/r4k-timer.h b/arch/mips/include/asm/r4k-timer.h
index a37d12b..afe9e0e 100644
--- a/arch/mips/include/asm/r4k-timer.h
+++ b/arch/mips/include/asm/r4k-timer.h
@@ -12,16 +12,16 @@
 
 #ifdef CONFIG_SYNC_R4K
 
-extern void synchronise_count_master(void);
-extern void synchronise_count_slave(void);
+extern void synchronise_count_master(int cpu);
+extern void synchronise_count_slave(int cpu);
 
 #else
 
-static inline void synchronise_count_master(void)
+static inline void synchronise_count_master(int cpu)
 {
 }
 
-static inline void synchronise_count_slave(void)
+static inline void synchronise_count_slave(int cpu)
 {
 }
 
diff --git a/arch/mips/kernel/module.c b/arch/mips/kernel/module.c
index a5066b1..4f8c3cb 100644
--- a/arch/mips/kernel/module.c
+++ b/arch/mips/kernel/module.c
@@ -39,8 +39,6 @@
 	Elf_Addr value;
 };
 
-static struct mips_hi16 *mips_hi16_list;
-
 static LIST_HEAD(dbe_list);
 static DEFINE_SPINLOCK(dbe_lock);
 
@@ -128,8 +126,8 @@
 
 	n->addr = (Elf_Addr *)location;
 	n->value = v;
-	n->next = mips_hi16_list;
-	mips_hi16_list = n;
+	n->next = me->arch.r_mips_hi16_list;
+	me->arch.r_mips_hi16_list = n;
 
 	return 0;
 }
@@ -142,18 +140,28 @@
 	return 0;
 }
 
+static void free_relocation_chain(struct mips_hi16 *l)
+{
+	struct mips_hi16 *next;
+
+	while (l) {
+		next = l->next;
+		kfree(l);
+		l = next;
+	}
+}
+
 static int apply_r_mips_lo16_rel(struct module *me, u32 *location, Elf_Addr v)
 {
 	unsigned long insnlo = *location;
+	struct mips_hi16 *l;
 	Elf_Addr val, vallo;
 
 	/* Sign extend the addend we extract from the lo insn.  */
 	vallo = ((insnlo & 0xffff) ^ 0x8000) - 0x8000;
 
-	if (mips_hi16_list != NULL) {
-		struct mips_hi16 *l;
-
-		l = mips_hi16_list;
+	if (me->arch.r_mips_hi16_list != NULL) {
+		l = me->arch.r_mips_hi16_list;
 		while (l != NULL) {
 			struct mips_hi16 *next;
 			unsigned long insn;
@@ -188,7 +196,7 @@
 			l = next;
 		}
 
-		mips_hi16_list = NULL;
+		me->arch.r_mips_hi16_list = NULL;
 	}
 
 	/*
@@ -201,6 +209,9 @@
 	return 0;
 
 out_danger:
+	free_relocation_chain(l);
+	me->arch.r_mips_hi16_list = NULL;
+
 	pr_err("module %s: dangerous R_MIPS_LO16 REL relocation\n", me->name);
 
 	return -ENOEXEC;
@@ -273,6 +284,7 @@
 	pr_debug("Applying relocate section %u to %u\n", relsec,
 	       sechdrs[relsec].sh_info);
 
+	me->arch.r_mips_hi16_list = NULL;
 	for (i = 0; i < sechdrs[relsec].sh_size / sizeof(*rel); i++) {
 		/* This is where to make the change */
 		location = (void *)sechdrs[sechdrs[relsec].sh_info].sh_addr
@@ -296,6 +308,19 @@
 			return res;
 	}
 
+	/*
+	 * Normally the hi16 list should be deallocated at this point.  A
+	 * malformed binary however could contain a series of R_MIPS_HI16
+	 * relocations not followed by a R_MIPS_LO16 relocation.  In that
+	 * case, free up the list and return an error.
+	 */
+	if (me->arch.r_mips_hi16_list) {
+		free_relocation_chain(me->arch.r_mips_hi16_list);
+		me->arch.r_mips_hi16_list = NULL;
+
+		return -ENOEXEC;
+	}
+
 	return 0;
 }
 
diff --git a/arch/mips/kernel/smp.c b/arch/mips/kernel/smp.c
index 31637d8..9005bf9 100644
--- a/arch/mips/kernel/smp.c
+++ b/arch/mips/kernel/smp.c
@@ -130,7 +130,7 @@
 
 	cpu_set(cpu, cpu_callin_map);
 
-	synchronise_count_slave();
+	synchronise_count_slave(cpu);
 
 	/*
 	 * irq will be enabled in ->smp_finish(), enabling it too early
@@ -173,7 +173,6 @@
 void __init smp_cpus_done(unsigned int max_cpus)
 {
 	mp_ops->cpus_done();
-	synchronise_count_master();
 }
 
 /* called from main before smp_init() */
@@ -206,6 +205,7 @@
 	while (!cpu_isset(cpu, cpu_callin_map))
 		udelay(100);
 
+	synchronise_count_master(cpu);
 	return 0;
 }
 
diff --git a/arch/mips/kernel/sync-r4k.c b/arch/mips/kernel/sync-r4k.c
index 842d55e..7f1eca3 100644
--- a/arch/mips/kernel/sync-r4k.c
+++ b/arch/mips/kernel/sync-r4k.c
@@ -28,12 +28,11 @@
 #define COUNTON	100
 #define NR_LOOPS 5
 
-void __cpuinit synchronise_count_master(void)
+void __cpuinit synchronise_count_master(int cpu)
 {
 	int i;
 	unsigned long flags;
 	unsigned int initcount;
-	int nslaves;
 
 #ifdef CONFIG_MIPS_MT_SMTC
 	/*
@@ -43,8 +42,7 @@
 	return;
 #endif
 
-	printk(KERN_INFO "Synchronize counters across %u CPUs: ",
-	       num_online_cpus());
+	printk(KERN_INFO "Synchronize counters for CPU %u: ", cpu);
 
 	local_irq_save(flags);
 
@@ -52,7 +50,7 @@
 	 * Notify the slaves that it's time to start
 	 */
 	atomic_set(&count_reference, read_c0_count());
-	atomic_set(&count_start_flag, 1);
+	atomic_set(&count_start_flag, cpu);
 	smp_wmb();
 
 	/* Count will be initialised to current timer for all CPU's */
@@ -69,10 +67,9 @@
 	 * two CPUs.
 	 */
 
-	nslaves = num_online_cpus()-1;
 	for (i = 0; i < NR_LOOPS; i++) {
-		/* slaves loop on '!= ncpus' */
-		while (atomic_read(&count_count_start) != nslaves)
+		/* slaves loop on '!= 2' */
+		while (atomic_read(&count_count_start) != 1)
 			mb();
 		atomic_set(&count_count_stop, 0);
 		smp_wmb();
@@ -89,7 +86,7 @@
 		/*
 		 * Wait for all slaves to leave the synchronization point:
 		 */
-		while (atomic_read(&count_count_stop) != nslaves)
+		while (atomic_read(&count_count_stop) != 1)
 			mb();
 		atomic_set(&count_count_start, 0);
 		smp_wmb();
@@ -97,6 +94,7 @@
 	}
 	/* Arrange for an interrupt in a short while */
 	write_c0_compare(read_c0_count() + COUNTON);
+	atomic_set(&count_start_flag, 0);
 
 	local_irq_restore(flags);
 
@@ -108,11 +106,10 @@
 	printk("done.\n");
 }
 
-void __cpuinit synchronise_count_slave(void)
+void __cpuinit synchronise_count_slave(int cpu)
 {
 	int i;
 	unsigned int initcount;
-	int ncpus;
 
 #ifdef CONFIG_MIPS_MT_SMTC
 	/*
@@ -127,16 +124,15 @@
 	 * so we first wait for the master to say everyone is ready
 	 */
 
-	while (!atomic_read(&count_start_flag))
+	while (atomic_read(&count_start_flag) != cpu)
 		mb();
 
 	/* Count will be initialised to next expire for all CPU's */
 	initcount = atomic_read(&count_reference);
 
-	ncpus = num_online_cpus();
 	for (i = 0; i < NR_LOOPS; i++) {
 		atomic_inc(&count_count_start);
-		while (atomic_read(&count_count_start) != ncpus)
+		while (atomic_read(&count_count_start) != 2)
 			mb();
 
 		/*
@@ -146,7 +142,7 @@
 			write_c0_count(initcount);
 
 		atomic_inc(&count_count_stop);
-		while (atomic_read(&count_count_stop) != ncpus)
+		while (atomic_read(&count_count_stop) != 2)
 			mb();
 	}
 	/* Arrange for an interrupt in a short while */
diff --git a/arch/mips/mti-malta/malta-pci.c b/arch/mips/mti-malta/malta-pci.c
index 284dea5..2147cb3 100644
--- a/arch/mips/mti-malta/malta-pci.c
+++ b/arch/mips/mti-malta/malta-pci.c
@@ -252,16 +252,3 @@
 
 	register_pci_controller(controller);
 }
-
-/* Enable PCI 2.1 compatibility in PIIX4 */
-static void __devinit quirk_dlcsetup(struct pci_dev *dev)
-{
-	u8 odlc, ndlc;
-	(void) pci_read_config_byte(dev, 0x82, &odlc);
-	/* Enable passive releases and delayed transaction */
-	ndlc = odlc | 7;
-	(void) pci_write_config_byte(dev, 0x82, ndlc);
-}
-
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371AB_0,
-	quirk_dlcsetup);
diff --git a/arch/mips/pci/pci-ar724x.c b/arch/mips/pci/pci-ar724x.c
index 414a745..86d77a6 100644
--- a/arch/mips/pci/pci-ar724x.c
+++ b/arch/mips/pci/pci-ar724x.c
@@ -23,9 +23,12 @@
 #define AR724X_PCI_MEM_BASE	0x10000000
 #define AR724X_PCI_MEM_SIZE	0x08000000
 
+#define AR724X_PCI_REG_RESET		0x18
 #define AR724X_PCI_REG_INT_STATUS	0x4c
 #define AR724X_PCI_REG_INT_MASK		0x50
 
+#define AR724X_PCI_RESET_LINK_UP	BIT(0)
+
 #define AR724X_PCI_INT_DEV0		BIT(14)
 
 #define AR724X_PCI_IRQ_COUNT		1
@@ -38,6 +41,15 @@
 
 static u32 ar724x_pci_bar0_value;
 static bool ar724x_pci_bar0_is_cached;
+static bool ar724x_pci_link_up;
+
+static inline bool ar724x_pci_check_link(void)
+{
+	u32 reset;
+
+	reset = __raw_readl(ar724x_pci_ctrl_base + AR724X_PCI_REG_RESET);
+	return reset & AR724X_PCI_RESET_LINK_UP;
+}
 
 static int ar724x_pci_read(struct pci_bus *bus, unsigned int devfn, int where,
 			    int size, uint32_t *value)
@@ -46,6 +58,9 @@
 	void __iomem *base;
 	u32 data;
 
+	if (!ar724x_pci_link_up)
+		return PCIBIOS_DEVICE_NOT_FOUND;
+
 	if (devfn)
 		return PCIBIOS_DEVICE_NOT_FOUND;
 
@@ -96,6 +111,9 @@
 	u32 data;
 	int s;
 
+	if (!ar724x_pci_link_up)
+		return PCIBIOS_DEVICE_NOT_FOUND;
+
 	if (devfn)
 		return PCIBIOS_DEVICE_NOT_FOUND;
 
@@ -280,6 +298,10 @@
 	if (ar724x_pci_ctrl_base == NULL)
 		goto err_unmap_devcfg;
 
+	ar724x_pci_link_up = ar724x_pci_check_link();
+	if (!ar724x_pci_link_up)
+		pr_warn("ar724x: PCIe link is down\n");
+
 	ar724x_pci_irq_init(irq);
 	register_pci_controller(&ar724x_pci_controller);
 
diff --git a/arch/mips/sni/a20r.c b/arch/mips/sni/a20r.c
index c48194c..b2d4f49 100644
--- a/arch/mips/sni/a20r.c
+++ b/arch/mips/sni/a20r.c
@@ -133,6 +133,38 @@
 	}
 };
 
+#warning "Please try migrate to use new driver SCCNXP and report the status" \
+	 "in the linux-serial mailing list."
+
+/* The code bellow is a replacement of SC26XX to SCCNXP */
+#if 0
+#include <linux/platform_data/sccnxp.h>
+
+static struct sccnxp_pdata sccnxp_data = {
+	.reg_shift	= 2,
+	.frequency	= 3686400,
+	.mctrl_cfg[0]	= MCTRL_SIG(DTR_OP, LINE_OP7) |
+			  MCTRL_SIG(RTS_OP, LINE_OP3) |
+			  MCTRL_SIG(DSR_IP, LINE_IP5) |
+			  MCTRL_SIG(DCD_IP, LINE_IP6),
+	.mctrl_cfg[1]	= MCTRL_SIG(DTR_OP, LINE_OP2) |
+			  MCTRL_SIG(RTS_OP, LINE_OP1) |
+			  MCTRL_SIG(DSR_IP, LINE_IP0) |
+			  MCTRL_SIG(CTS_IP, LINE_IP1) |
+			  MCTRL_SIG(DCD_IP, LINE_IP2) |
+			  MCTRL_SIG(RNG_IP, LINE_IP3),
+};
+
+static struct platform_device sc2681_pdev = {
+	.name		= "sc2681",
+	.resource	= sc2xxx_rsrc,
+	.num_resources	= ARRAY_SIZE(sc2xxx_rsrc),
+	.dev	= {
+		.platform_data	= &sccnxp_data,
+	},
+};
+#endif
+
 static u32 a20r_ack_hwint(void)
 {
 	u32 status = read_c0_status();
diff --git a/arch/parisc/include/asm/atomic.h b/arch/parisc/include/asm/atomic.h
index 6c6defc..af9cf30 100644
--- a/arch/parisc/include/asm/atomic.h
+++ b/arch/parisc/include/asm/atomic.h
@@ -141,7 +141,7 @@
 
 #define atomic_sub_and_test(i,v)	(atomic_sub_return((i),(v)) == 0)
 
-#define ATOMIC_INIT(i)	((atomic_t) { (i) })
+#define ATOMIC_INIT(i)	{ (i) }
 
 #define smp_mb__before_atomic_dec()	smp_mb()
 #define smp_mb__after_atomic_dec()	smp_mb()
@@ -150,7 +150,7 @@
 
 #ifdef CONFIG_64BIT
 
-#define ATOMIC64_INIT(i) ((atomic64_t) { (i) })
+#define ATOMIC64_INIT(i) { (i) }
 
 static __inline__ s64
 __atomic64_add_return(s64 i, atomic64_t *v)
diff --git a/arch/parisc/kernel/pdc_cons.c b/arch/parisc/kernel/pdc_cons.c
index 47341aa..8823863 100644
--- a/arch/parisc/kernel/pdc_cons.c
+++ b/arch/parisc/kernel/pdc_cons.c
@@ -202,6 +202,7 @@
 	pdc_console_tty_driver->flags = TTY_DRIVER_REAL_RAW |
 		TTY_DRIVER_RESET_TERMIOS;
 	tty_set_operations(pdc_console_tty_driver, &pdc_console_tty_ops);
+	tty_port_link_device(&tty_port, pdc_console_tty_driver, 0);
 
 	err = tty_register_driver(pdc_console_tty_driver);
 	if (err) {
diff --git a/arch/parisc/kernel/process.c b/arch/parisc/kernel/process.c
index d4b94b3..2c05a929 100644
--- a/arch/parisc/kernel/process.c
+++ b/arch/parisc/kernel/process.c
@@ -309,7 +309,7 @@
 		cregs->ksp = (unsigned long)stack
 			+ (pregs->gr[21] & (THREAD_SIZE - 1));
 		cregs->gr[30] = usp;
-		if (p->personality == PER_HPUX) {
+		if (personality(p->personality) == PER_HPUX) {
 #ifdef CONFIG_HPUX
 			cregs->kpc = (unsigned long) &hpux_child_return;
 #else
diff --git a/arch/parisc/kernel/sys_parisc.c b/arch/parisc/kernel/sys_parisc.c
index c9b9322..7426e40 100644
--- a/arch/parisc/kernel/sys_parisc.c
+++ b/arch/parisc/kernel/sys_parisc.c
@@ -225,12 +225,12 @@
 	long err;
 
 	if (personality(current->personality) == PER_LINUX32
-	    && personality == PER_LINUX)
-		personality = PER_LINUX32;
+	    && personality(personality) == PER_LINUX)
+		personality = (personality & ~PER_MASK) | PER_LINUX32;
 
 	err = sys_personality(personality);
-	if (err == PER_LINUX32)
-		err = PER_LINUX;
+	if (personality(err) == PER_LINUX32)
+		err = (err & ~PER_MASK) | PER_LINUX;
 
 	return err;
 }
diff --git a/arch/powerpc/boot/dts/fsl/p4080si-post.dtsi b/arch/powerpc/boot/dts/fsl/p4080si-post.dtsi
index 8d35d2c..4f9c9f6 100644
--- a/arch/powerpc/boot/dts/fsl/p4080si-post.dtsi
+++ b/arch/powerpc/boot/dts/fsl/p4080si-post.dtsi
@@ -345,6 +345,13 @@
 /include/ "qoriq-duart-1.dtsi"
 /include/ "qoriq-gpio-0.dtsi"
 /include/ "qoriq-usb2-mph-0.dtsi"
+	usb@210000 {
+		compatible = "fsl-usb2-mph-v1.6", "fsl,mpc85xx-usb2-mph", "fsl-usb2-mph";
+		port0;
+	};
 /include/ "qoriq-usb2-dr-0.dtsi"
+	usb@211000 {
+		compatible = "fsl-usb2-dr-v1.6", "fsl,mpc85xx-usb2-dr", "fsl-usb2-dr";
+	};
 /include/ "qoriq-sec4.0-0.dtsi"
 };
diff --git a/arch/powerpc/configs/85xx/p1023rds_defconfig b/arch/powerpc/configs/85xx/p1023rds_defconfig
index f4337ba..26e541c 100644
--- a/arch/powerpc/configs/85xx/p1023rds_defconfig
+++ b/arch/powerpc/configs/85xx/p1023rds_defconfig
@@ -6,28 +6,27 @@
 CONFIG_POSIX_MQUEUE=y
 CONFIG_BSD_PROCESS_ACCT=y
 CONFIG_AUDIT=y
-CONFIG_SPARSE_IRQ=y
+CONFIG_IRQ_DOMAIN_DEBUG=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
 CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_BLK_DEV_INITRD=y
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
 CONFIG_KALLSYMS_ALL=y
-CONFIG_KALLSYMS_EXTRA_PASS=y
 CONFIG_EMBEDDED=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
 CONFIG_MODULE_FORCE_UNLOAD=y
 CONFIG_MODVERSIONS=y
 # CONFIG_BLK_DEV_BSG is not set
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_MAC_PARTITION=y
 CONFIG_P1023_RDS=y
 CONFIG_QUICC_ENGINE=y
 CONFIG_QE_GPIO=y
 CONFIG_CPM2=y
-CONFIG_GPIO_MPC8XXX=y
 CONFIG_HIGHMEM=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
 # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
 CONFIG_BINFMT_MISC=m
 CONFIG_MATH_EMULATION=y
@@ -63,11 +62,11 @@
 CONFIG_IPV6=y
 CONFIG_IP_SCTP=m
 CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
 CONFIG_PROC_DEVICETREE=y
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_RAM=y
 CONFIG_BLK_DEV_RAM_SIZE=131072
-CONFIG_MISC_DEVICES=y
 CONFIG_EEPROM_LEGACY=y
 CONFIG_BLK_DEV_SD=y
 CONFIG_CHR_DEV_ST=y
@@ -80,15 +79,14 @@
 CONFIG_SATA_SIL24=y
 CONFIG_NETDEVICES=y
 CONFIG_DUMMY=y
+CONFIG_FS_ENET=y
+CONFIG_FSL_PQ_MDIO=y
+CONFIG_E1000E=y
 CONFIG_MARVELL_PHY=y
 CONFIG_DAVICOM_PHY=y
 CONFIG_CICADA_PHY=y
 CONFIG_VITESSE_PHY=y
 CONFIG_FIXED_PHY=y
-CONFIG_NET_ETHERNET=y
-CONFIG_FS_ENET=y
-CONFIG_E1000E=y
-CONFIG_FSL_PQ_MDIO=y
 CONFIG_INPUT_FF_MEMLESS=m
 # CONFIG_INPUT_MOUSEDEV is not set
 # CONFIG_INPUT_KEYBOARD is not set
@@ -98,16 +96,15 @@
 CONFIG_SERIAL_8250_CONSOLE=y
 CONFIG_SERIAL_8250_NR_UARTS=2
 CONFIG_SERIAL_8250_RUNTIME_UARTS=2
-CONFIG_SERIAL_8250_EXTENDED=y
 CONFIG_SERIAL_8250_MANY_PORTS=y
 CONFIG_SERIAL_8250_DETECT_IRQ=y
 CONFIG_SERIAL_8250_RSA=y
 CONFIG_SERIAL_QE=m
-CONFIG_HW_RANDOM=y
 CONFIG_NVRAM=y
 CONFIG_I2C=y
 CONFIG_I2C_CPM=m
 CONFIG_I2C_MPC=y
+CONFIG_GPIO_MPC8XXX=y
 # CONFIG_HWMON is not set
 CONFIG_VIDEO_OUTPUT_CONTROL=y
 CONFIG_SOUND=y
@@ -123,7 +120,6 @@
 CONFIG_FSL_DMA=y
 # CONFIG_NET_DMA is not set
 CONFIG_STAGING=y
-# CONFIG_STAGING_EXCLUDE_BUILD is not set
 CONFIG_EXT2_FS=y
 CONFIG_EXT3_FS=y
 # CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
@@ -150,22 +146,15 @@
 CONFIG_SYSV_FS=m
 CONFIG_UFS_FS=m
 CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
 CONFIG_NFS_V4=y
 CONFIG_ROOT_NFS=y
 CONFIG_NFSD=y
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_MAC_PARTITION=y
 CONFIG_CRC_T10DIF=y
 CONFIG_FRAME_WARN=8092
 CONFIG_DEBUG_FS=y
-CONFIG_DEBUG_KERNEL=y
 CONFIG_DETECT_HUNG_TASK=y
 # CONFIG_DEBUG_BUGVERBOSE is not set
 CONFIG_DEBUG_INFO=y
-# CONFIG_RCU_CPU_STALL_DETECTOR is not set
-CONFIG_SYSCTL_SYSCALL_CHECK=y
-CONFIG_IRQ_DOMAIN_DEBUG=y
 CONFIG_CRYPTO_PCBC=m
 CONFIG_CRYPTO_SHA256=y
 CONFIG_CRYPTO_SHA512=y
diff --git a/arch/powerpc/configs/corenet32_smp_defconfig b/arch/powerpc/configs/corenet32_smp_defconfig
index cbb98c1..8b3d57c 100644
--- a/arch/powerpc/configs/corenet32_smp_defconfig
+++ b/arch/powerpc/configs/corenet32_smp_defconfig
@@ -6,8 +6,8 @@
 CONFIG_POSIX_MQUEUE=y
 CONFIG_BSD_PROCESS_ACCT=y
 CONFIG_AUDIT=y
-CONFIG_SPARSE_IRQ=y
-CONFIG_RCU_TRACE=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
 CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
 CONFIG_LOG_BUF_SHIFT=14
@@ -21,23 +21,22 @@
 CONFIG_MODULE_FORCE_UNLOAD=y
 CONFIG_MODVERSIONS=y
 # CONFIG_BLK_DEV_BSG is not set
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_MAC_PARTITION=y
 CONFIG_P2041_RDB=y
 CONFIG_P3041_DS=y
 CONFIG_P4080_DS=y
 CONFIG_P5020_DS=y
 CONFIG_HIGHMEM=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
 # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
 CONFIG_BINFMT_MISC=m
 CONFIG_KEXEC=y
 CONFIG_IRQ_ALL_CPUS=y
 CONFIG_FORCE_MAX_ZONEORDER=13
-CONFIG_FSL_LBC=y
 CONFIG_PCI=y
 CONFIG_PCIEPORTBUS=y
-CONFIG_PCI_MSI=y
 # CONFIG_PCIEASPM is not set
+CONFIG_PCI_MSI=y
 CONFIG_RAPIDIO=y
 CONFIG_FSL_RIO=y
 CONFIG_NET=y
@@ -70,6 +69,7 @@
 CONFIG_IPV6=y
 CONFIG_IP_SCTP=m
 CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
 CONFIG_MTD=y
 CONFIG_MTD_CMDLINE_PARTS=y
 CONFIG_MTD_CHAR=y
@@ -77,17 +77,14 @@
 CONFIG_MTD_CFI=y
 CONFIG_MTD_CFI_AMDSTD=y
 CONFIG_MTD_PHYSMAP_OF=y
-CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_ECC=y
-CONFIG_MTD_NAND_IDS=y
-CONFIG_MTD_NAND_FSL_IFC=y
-CONFIG_MTD_NAND_FSL_ELBC=y
 CONFIG_MTD_M25P80=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_FSL_ELBC=y
+CONFIG_MTD_NAND_FSL_IFC=y
 CONFIG_PROC_DEVICETREE=y
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_RAM=y
 CONFIG_BLK_DEV_RAM_SIZE=131072
-CONFIG_MISC_DEVICES=y
 CONFIG_BLK_DEV_SD=y
 CONFIG_CHR_DEV_ST=y
 CONFIG_BLK_DEV_SR=y
@@ -115,11 +112,9 @@
 CONFIG_PPC_EPAPR_HV_BYTECHAN=y
 CONFIG_SERIAL_8250=y
 CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_SERIAL_8250_EXTENDED=y
 CONFIG_SERIAL_8250_MANY_PORTS=y
 CONFIG_SERIAL_8250_DETECT_IRQ=y
 CONFIG_SERIAL_8250_RSA=y
-CONFIG_HW_RANDOM=y
 CONFIG_NVRAM=y
 CONFIG_I2C=y
 CONFIG_I2C_CHARDEV=y
@@ -132,7 +127,6 @@
 CONFIG_VIDEO_OUTPUT_CONTROL=y
 CONFIG_USB_HID=m
 CONFIG_USB=y
-CONFIG_USB_DEVICEFS=y
 CONFIG_USB_MON=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_FSL=y
@@ -142,8 +136,6 @@
 CONFIG_USB_STORAGE=y
 CONFIG_MMC=y
 CONFIG_MMC_SDHCI=y
-CONFIG_MMC_SDHCI_OF=y
-CONFIG_MMC_SDHCI_OF_ESDHC=y
 CONFIG_EDAC=y
 CONFIG_EDAC_MM_EDAC=y
 CONFIG_EDAC_MPC85XX=y
@@ -170,19 +162,16 @@
 CONFIG_JFFS2_FS=y
 CONFIG_CRAMFS=y
 CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
 CONFIG_NFS_V4=y
 CONFIG_ROOT_NFS=y
 CONFIG_NFSD=m
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_MAC_PARTITION=y
 CONFIG_NLS_ISO8859_1=y
 CONFIG_NLS_UTF8=m
 CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_SHIRQ=y
 CONFIG_DETECT_HUNG_TASK=y
 CONFIG_DEBUG_INFO=y
-CONFIG_SYSCTL_SYSCALL_CHECK=y
+CONFIG_RCU_TRACE=y
 CONFIG_CRYPTO_NULL=y
 CONFIG_CRYPTO_PCBC=m
 CONFIG_CRYPTO_MD4=y
diff --git a/arch/powerpc/configs/corenet64_smp_defconfig b/arch/powerpc/configs/corenet64_smp_defconfig
index dd89de8..0516e22 100644
--- a/arch/powerpc/configs/corenet64_smp_defconfig
+++ b/arch/powerpc/configs/corenet64_smp_defconfig
@@ -56,6 +56,7 @@
 CONFIG_IPV6=y
 CONFIG_IP_SCTP=m
 CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
 CONFIG_MTD=y
 CONFIG_MTD_CMDLINE_PARTS=y
 CONFIG_MTD_CHAR=y
diff --git a/arch/powerpc/configs/g5_defconfig b/arch/powerpc/configs/g5_defconfig
index 1513006..07b7f2a 100644
--- a/arch/powerpc/configs/g5_defconfig
+++ b/arch/powerpc/configs/g5_defconfig
@@ -1,8 +1,10 @@
+CONFIG_PPC64=y
+CONFIG_ALTIVEC=y
+CONFIG_SMP=y
+CONFIG_NR_CPUS=4
 CONFIG_EXPERIMENTAL=y
 CONFIG_SYSVIPC=y
 CONFIG_POSIX_MQUEUE=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
 CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
 CONFIG_BLK_DEV_INITRD=y
@@ -13,15 +15,16 @@
 CONFIG_MODULE_UNLOAD=y
 CONFIG_MODVERSIONS=y
 CONFIG_MODULE_SRCVERSION_ALL=y
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_MAC_PARTITION=y
-CONFIG_SMP=y
-CONFIG_NR_CPUS=4
-CONFIG_KEXEC=y
-# CONFIG_RELOCATABLE is not set
+# CONFIG_PPC_PSERIES is not set
 CONFIG_CPU_FREQ=y
 CONFIG_CPU_FREQ_GOV_POWERSAVE=y
 CONFIG_CPU_FREQ_GOV_USERSPACE=y
+CONFIG_CPU_FREQ_PMAC64=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_KEXEC=y
+CONFIG_IRQ_ALL_CPUS=y
+# CONFIG_MIGRATION is not set
 CONFIG_PCI_MSI=y
 CONFIG_NET=y
 CONFIG_PACKET=y
@@ -49,6 +52,7 @@
 CONFIG_NF_CONNTRACK_IPV4=m
 CONFIG_IP_NF_QUEUE=m
 CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_PROC_DEVICETREE=y
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_NBD=m
 CONFIG_BLK_DEV_RAM=y
@@ -56,6 +60,8 @@
 CONFIG_CDROM_PKTCDVD=m
 CONFIG_IDE=y
 CONFIG_BLK_DEV_IDECD=y
+CONFIG_BLK_DEV_IDE_PMAC=y
+CONFIG_BLK_DEV_IDE_PMAC_ATA100FIRST=y
 CONFIG_BLK_DEV_SD=y
 CONFIG_CHR_DEV_ST=y
 CONFIG_BLK_DEV_SR=y
@@ -79,24 +85,33 @@
 CONFIG_DM_SNAPSHOT=m
 CONFIG_DM_MIRROR=m
 CONFIG_DM_ZERO=m
-CONFIG_MACINTOSH_DRIVERS=y
+CONFIG_IEEE1394=y
+CONFIG_IEEE1394_OHCI1394=y
+CONFIG_IEEE1394_SBP2=m
+CONFIG_IEEE1394_ETH1394=m
+CONFIG_IEEE1394_RAWIO=y
+CONFIG_IEEE1394_VIDEO1394=m
+CONFIG_IEEE1394_DV1394=m
+CONFIG_ADB_PMU=y
+CONFIG_PMAC_SMU=y
 CONFIG_MAC_EMUMOUSEBTN=y
+CONFIG_THERM_PM72=y
+CONFIG_WINDFARM=y
+CONFIG_WINDFARM_PM81=y
+CONFIG_WINDFARM_PM91=y
+CONFIG_WINDFARM_PM112=y
+CONFIG_WINDFARM_PM121=y
 CONFIG_NETDEVICES=y
-CONFIG_BONDING=m
 CONFIG_DUMMY=m
-CONFIG_MII=y
+CONFIG_BONDING=m
 CONFIG_TUN=m
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+CONFIG_SUNGEM=y
 CONFIG_ACENIC=m
 CONFIG_ACENIC_OMIT_TIGON_I=y
-CONFIG_TIGON3=y
 CONFIG_E1000=y
-CONFIG_SUNGEM=y
-CONFIG_PPP=m
-CONFIG_PPP_BSDCOMP=m
-CONFIG_PPP_DEFLATE=m
-CONFIG_PPPOE=m
-CONFIG_PPP_ASYNC=m
-CONFIG_PPP_SYNC_TTY=m
+CONFIG_TIGON3=y
 CONFIG_USB_CATC=m
 CONFIG_USB_KAWETH=m
 CONFIG_USB_PEGASUS=m
@@ -106,24 +121,36 @@
 # CONFIG_USB_NET_NET1080 is not set
 # CONFIG_USB_NET_CDC_SUBSET is not set
 # CONFIG_USB_NET_ZAURUS is not set
+CONFIG_PPP=m
+CONFIG_PPP_ASYNC=m
+CONFIG_PPP_SYNC_TTY=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_BSDCOMP=m
+CONFIG_PPPOE=m
 # CONFIG_INPUT_MOUSEDEV_PSAUX is not set
 CONFIG_INPUT_JOYDEV=m
 CONFIG_INPUT_EVDEV=y
+# CONFIG_KEYBOARD_ATKBD is not set
 # CONFIG_MOUSE_PS2 is not set
+# CONFIG_SERIO_I8042 is not set
 # CONFIG_SERIO_SERPORT is not set
-CONFIG_VT_HW_CONSOLE_BINDING=y
 # CONFIG_HW_RANDOM is not set
 CONFIG_GEN_RTC=y
 CONFIG_RAW_DRIVER=y
 CONFIG_I2C_CHARDEV=y
 # CONFIG_HWMON is not set
-CONFIG_AGP=y
-CONFIG_DRM=y
-CONFIG_DRM_NOUVEAU=y
+CONFIG_AGP=m
+CONFIG_AGP_UNINORTH=m
 CONFIG_VIDEO_OUTPUT_CONTROL=m
+CONFIG_FB=y
 CONFIG_FIRMWARE_EDID=y
 CONFIG_FB_TILEBLITTING=y
+CONFIG_FB_OF=y
+CONFIG_FB_NVIDIA=y
+CONFIG_FB_NVIDIA_I2C=y
 CONFIG_FB_RADEON=y
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_FRAMEBUFFER_CONSOLE=y
 CONFIG_LOGO=y
 CONFIG_SOUND=m
 CONFIG_SND=m
@@ -131,7 +158,15 @@
 CONFIG_SND_MIXER_OSS=m
 CONFIG_SND_PCM_OSS=m
 CONFIG_SND_SEQUENCER_OSS=y
+CONFIG_SND_POWERMAC=m
+CONFIG_SND_AOA=m
+CONFIG_SND_AOA_FABRIC_LAYOUT=m
+CONFIG_SND_AOA_ONYX=m
+CONFIG_SND_AOA_TAS=m
+CONFIG_SND_AOA_TOONIE=m
 CONFIG_SND_USB_AUDIO=m
+CONFIG_HID_PID=y
+CONFIG_USB_HIDDEV=y
 CONFIG_HID_GYRATION=y
 CONFIG_LOGITECH_FF=y
 CONFIG_HID_PANTHERLORD=y
@@ -139,12 +174,13 @@
 CONFIG_HID_SAMSUNG=y
 CONFIG_HID_SONY=y
 CONFIG_HID_SUNPLUS=y
-CONFIG_HID_PID=y
-CONFIG_USB_HIDDEV=y
 CONFIG_USB=y
+CONFIG_USB_DEVICEFS=y
 CONFIG_USB_MON=y
 CONFIG_USB_EHCI_HCD=y
+# CONFIG_USB_EHCI_HCD_PPC_OF is not set
 CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_OHCI_HCD_PPC_OF_BE=y
 CONFIG_USB_ACM=m
 CONFIG_USB_PRINTER=y
 CONFIG_USB_STORAGE=y
@@ -208,6 +244,8 @@
 CONFIG_REISERFS_FS_SECURITY=y
 CONFIG_XFS_FS=m
 CONFIG_XFS_POSIX_ACL=y
+CONFIG_INOTIFY=y
+CONFIG_AUTOFS_FS=m
 CONFIG_ISO9660_FS=y
 CONFIG_JOLIET=y
 CONFIG_ZISOFS=y
@@ -221,12 +259,14 @@
 CONFIG_HFSPLUS_FS=m
 CONFIG_CRAMFS=y
 CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
 CONFIG_NFS_V3_ACL=y
 CONFIG_NFS_V4=y
 CONFIG_NFSD=y
 CONFIG_NFSD_V3_ACL=y
 CONFIG_NFSD_V4=y
 CONFIG_CIFS=m
+CONFIG_PARTITION_ADVANCED=y
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_CODEPAGE_1250=y
 CONFIG_NLS_CODEPAGE_1251=y
@@ -234,23 +274,29 @@
 CONFIG_NLS_ISO8859_1=y
 CONFIG_NLS_ISO8859_15=y
 CONFIG_NLS_UTF8=y
+CONFIG_CRC_T10DIF=y
+CONFIG_LIBCRC32C=m
 CONFIG_MAGIC_SYSRQ=y
-# CONFIG_UNUSED_SYMBOLS is not set
 CONFIG_DEBUG_FS=y
 CONFIG_DEBUG_KERNEL=y
 CONFIG_DEBUG_MUTEXES=y
+# CONFIG_RCU_CPU_STALL_DETECTOR is not set
 CONFIG_LATENCYTOP=y
-CONFIG_STRICT_DEVMEM=y
+CONFIG_SYSCTL_SYSCALL_CHECK=y
+CONFIG_BOOTX_TEXT=y
 CONFIG_CRYPTO_NULL=m
 CONFIG_CRYPTO_TEST=m
+CONFIG_CRYPTO_ECB=m
 CONFIG_CRYPTO_PCBC=m
 CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_MD4=m
 CONFIG_CRYPTO_MICHAEL_MIC=m
 CONFIG_CRYPTO_SHA256=m
 CONFIG_CRYPTO_SHA512=m
 CONFIG_CRYPTO_WP512=m
 CONFIG_CRYPTO_AES=m
 CONFIG_CRYPTO_ANUBIS=m
+CONFIG_CRYPTO_ARC4=m
 CONFIG_CRYPTO_BLOWFISH=m
 CONFIG_CRYPTO_CAST5=m
 CONFIG_CRYPTO_CAST6=m
@@ -260,6 +306,3 @@
 CONFIG_CRYPTO_TWOFISH=m
 # CONFIG_CRYPTO_ANSI_CPRNG is not set
 # CONFIG_CRYPTO_HW is not set
-# CONFIG_VIRTUALIZATION is not set
-CONFIG_CRC_T10DIF=y
-CONFIG_LIBCRC32C=m
diff --git a/arch/powerpc/configs/mpc83xx_defconfig b/arch/powerpc/configs/mpc83xx_defconfig
index 5aac9a8..9352e44 100644
--- a/arch/powerpc/configs/mpc83xx_defconfig
+++ b/arch/powerpc/configs/mpc83xx_defconfig
@@ -2,12 +2,12 @@
 CONFIG_SYSVIPC=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_BLK_DEV_INITRD=y
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
 CONFIG_EXPERT=y
 CONFIG_SLAB=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
 # CONFIG_BLK_DEV_BSG is not set
+CONFIG_PARTITION_ADVANCED=y
 # CONFIG_PPC_CHRP is not set
 # CONFIG_PPC_PMAC is not set
 CONFIG_PPC_83xx=y
@@ -25,7 +25,6 @@
 CONFIG_QUICC_ENGINE=y
 CONFIG_QE_GPIO=y
 CONFIG_MATH_EMULATION=y
-CONFIG_SPARSE_IRQ=y
 CONFIG_PCI=y
 CONFIG_NET=y
 CONFIG_PACKET=y
@@ -42,10 +41,9 @@
 # CONFIG_INET_LRO is not set
 # CONFIG_IPV6 is not set
 CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
 # CONFIG_FW_LOADER is not set
 CONFIG_MTD=y
-CONFIG_MTD_PARTITIONS=y
-CONFIG_MTD_OF_PARTS=y
 CONFIG_MTD_CHAR=y
 CONFIG_MTD_BLOCK=y
 CONFIG_MTD_CFI=y
@@ -64,15 +62,14 @@
 CONFIG_SATA_FSL=y
 CONFIG_SATA_SIL=y
 CONFIG_NETDEVICES=y
+CONFIG_MII=y
+CONFIG_UCC_GETH=y
+CONFIG_GIANFAR=y
 CONFIG_MARVELL_PHY=y
 CONFIG_DAVICOM_PHY=y
 CONFIG_VITESSE_PHY=y
 CONFIG_ICPLUS_PHY=y
 CONFIG_FIXED_PHY=y
-CONFIG_NET_ETHERNET=y
-CONFIG_MII=y
-CONFIG_GIANFAR=y
-CONFIG_UCC_GETH=y
 CONFIG_INPUT_FF_MEMLESS=m
 # CONFIG_INPUT_MOUSEDEV is not set
 # CONFIG_INPUT_KEYBOARD is not set
@@ -112,17 +109,12 @@
 CONFIG_EXT2_FS=y
 CONFIG_EXT3_FS=y
 # CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
-CONFIG_INOTIFY=y
 CONFIG_PROC_KCORE=y
 CONFIG_TMPFS=y
 CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
 CONFIG_NFS_V4=y
 CONFIG_ROOT_NFS=y
-CONFIG_PARTITION_ADVANCED=y
 CONFIG_CRC_T10DIF=y
-# CONFIG_RCU_CPU_STALL_DETECTOR is not set
-CONFIG_SYSCTL_SYSCALL_CHECK=y
 CONFIG_CRYPTO_ECB=m
 CONFIG_CRYPTO_PCBC=m
 CONFIG_CRYPTO_SHA256=y
diff --git a/arch/powerpc/configs/mpc85xx_defconfig b/arch/powerpc/configs/mpc85xx_defconfig
index 03ee911c..8b5bda2 100644
--- a/arch/powerpc/configs/mpc85xx_defconfig
+++ b/arch/powerpc/configs/mpc85xx_defconfig
@@ -5,7 +5,9 @@
 CONFIG_POSIX_MQUEUE=y
 CONFIG_BSD_PROCESS_ACCT=y
 CONFIG_AUDIT=y
-CONFIG_SPARSE_IRQ=y
+CONFIG_IRQ_DOMAIN_DEBUG=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
 CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
 CONFIG_LOG_BUF_SHIFT=14
@@ -17,6 +19,8 @@
 CONFIG_MODULE_FORCE_UNLOAD=y
 CONFIG_MODVERSIONS=y
 # CONFIG_BLK_DEV_BSG is not set
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_MAC_PARTITION=y
 CONFIG_MPC8540_ADS=y
 CONFIG_MPC8560_ADS=y
 CONFIG_MPC85xx_CDS=y
@@ -40,8 +44,6 @@
 CONFIG_QUICC_ENGINE=y
 CONFIG_QE_GPIO=y
 CONFIG_HIGHMEM=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
 CONFIG_BINFMT_MISC=m
 CONFIG_MATH_EMULATION=y
 CONFIG_FORCE_MAX_ZONEORDER=12
@@ -74,36 +76,25 @@
 CONFIG_IPV6=y
 CONFIG_IP_SCTP=m
 CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
 CONFIG_MTD=y
 CONFIG_MTD_CMDLINE_PARTS=y
 CONFIG_MTD_CHAR=y
 CONFIG_MTD_BLOCK=y
-CONFIG_MTD_CFI=y
 CONFIG_FTL=y
-CONFIG_MTD_GEN_PROBE=y
-CONFIG_MTD_MAP_BANK_WIDTH_1=y
-CONFIG_MTD_MAP_BANK_WIDTH_2=y
-CONFIG_MTD_MAP_BANK_WIDTH_4=y
-CONFIG_MTD_CFI_I1=y
-CONFIG_MTD_CFI_I2=y
+CONFIG_MTD_CFI=y
 CONFIG_MTD_CFI_INTELEXT=y
 CONFIG_MTD_CFI_AMDSTD=y
-CONFIG_MTD_CFI_UTIL=y
 CONFIG_MTD_PHYSMAP_OF=y
-CONFIG_MTD_PARTITIONS=y
-CONFIG_MTD_OF_PARTS=y
+CONFIG_MTD_M25P80=y
 CONFIG_MTD_NAND=y
 CONFIG_MTD_NAND_FSL_ELBC=y
 CONFIG_MTD_NAND_FSL_IFC=y
-CONFIG_MTD_NAND_IDS=y
-CONFIG_MTD_NAND_ECC=y
-CONFIG_MTD_M25P80=y
 CONFIG_PROC_DEVICETREE=y
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_NBD=y
 CONFIG_BLK_DEV_RAM=y
 CONFIG_BLK_DEV_RAM_SIZE=131072
-CONFIG_MISC_DEVICES=y
 CONFIG_EEPROM_LEGACY=y
 CONFIG_BLK_DEV_SD=y
 CONFIG_CHR_DEV_ST=y
@@ -115,6 +106,7 @@
 CONFIG_SATA_AHCI=y
 CONFIG_SATA_FSL=y
 CONFIG_PATA_ALI=y
+CONFIG_PATA_VIA=y
 CONFIG_NETDEVICES=y
 CONFIG_DUMMY=y
 CONFIG_FS_ENET=y
@@ -134,7 +126,6 @@
 CONFIG_SERIAL_8250_CONSOLE=y
 CONFIG_SERIAL_8250_NR_UARTS=2
 CONFIG_SERIAL_8250_RUNTIME_UARTS=2
-CONFIG_SERIAL_8250_EXTENDED=y
 CONFIG_SERIAL_8250_MANY_PORTS=y
 CONFIG_SERIAL_8250_DETECT_IRQ=y
 CONFIG_SERIAL_8250_RSA=y
@@ -183,7 +174,6 @@
 CONFIG_HID_SONY=y
 CONFIG_HID_SUNPLUS=y
 CONFIG_USB=y
-CONFIG_USB_DEVICEFS=y
 CONFIG_USB_MON=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_FSL=y
@@ -229,18 +219,13 @@
 CONFIG_SYSV_FS=m
 CONFIG_UFS_FS=m
 CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
 CONFIG_NFS_V4=y
 CONFIG_ROOT_NFS=y
 CONFIG_NFSD=y
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_MAC_PARTITION=y
 CONFIG_CRC_T10DIF=y
 CONFIG_DEBUG_FS=y
 CONFIG_DETECT_HUNG_TASK=y
 CONFIG_DEBUG_INFO=y
-CONFIG_SYSCTL_SYSCALL_CHECK=y
-CONFIG_IRQ_DOMAIN_DEBUG=y
 CONFIG_CRYPTO_PCBC=m
 CONFIG_CRYPTO_SHA256=y
 CONFIG_CRYPTO_SHA512=y
diff --git a/arch/powerpc/configs/mpc85xx_smp_defconfig b/arch/powerpc/configs/mpc85xx_smp_defconfig
index fdfa84d..b0974e7 100644
--- a/arch/powerpc/configs/mpc85xx_smp_defconfig
+++ b/arch/powerpc/configs/mpc85xx_smp_defconfig
@@ -7,7 +7,9 @@
 CONFIG_POSIX_MQUEUE=y
 CONFIG_BSD_PROCESS_ACCT=y
 CONFIG_AUDIT=y
-CONFIG_SPARSE_IRQ=y
+CONFIG_IRQ_DOMAIN_DEBUG=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
 CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
 CONFIG_LOG_BUF_SHIFT=14
@@ -19,6 +21,8 @@
 CONFIG_MODULE_FORCE_UNLOAD=y
 CONFIG_MODVERSIONS=y
 # CONFIG_BLK_DEV_BSG is not set
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_MAC_PARTITION=y
 CONFIG_MPC8540_ADS=y
 CONFIG_MPC8560_ADS=y
 CONFIG_MPC85xx_CDS=y
@@ -42,8 +46,6 @@
 CONFIG_QUICC_ENGINE=y
 CONFIG_QE_GPIO=y
 CONFIG_HIGHMEM=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
 CONFIG_BINFMT_MISC=m
 CONFIG_MATH_EMULATION=y
 CONFIG_IRQ_ALL_CPUS=y
@@ -77,36 +79,25 @@
 CONFIG_IPV6=y
 CONFIG_IP_SCTP=m
 CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
 CONFIG_MTD=y
 CONFIG_MTD_CMDLINE_PARTS=y
 CONFIG_MTD_CHAR=y
 CONFIG_MTD_BLOCK=y
-CONFIG_MTD_CFI=y
 CONFIG_FTL=y
-CONFIG_MTD_GEN_PROBE=y
-CONFIG_MTD_MAP_BANK_WIDTH_1=y
-CONFIG_MTD_MAP_BANK_WIDTH_2=y
-CONFIG_MTD_MAP_BANK_WIDTH_4=y
-CONFIG_MTD_CFI_I1=y
-CONFIG_MTD_CFI_I2=y
+CONFIG_MTD_CFI=y
 CONFIG_MTD_CFI_INTELEXT=y
 CONFIG_MTD_CFI_AMDSTD=y
-CONFIG_MTD_CFI_UTIL=y
 CONFIG_MTD_PHYSMAP_OF=y
-CONFIG_MTD_PARTITIONS=y
-CONFIG_MTD_OF_PARTS=y
+CONFIG_MTD_M25P80=y
 CONFIG_MTD_NAND=y
 CONFIG_MTD_NAND_FSL_ELBC=y
 CONFIG_MTD_NAND_FSL_IFC=y
-CONFIG_MTD_NAND_IDS=y
-CONFIG_MTD_NAND_ECC=y
-CONFIG_MTD_M25P80=y
 CONFIG_PROC_DEVICETREE=y
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_NBD=y
 CONFIG_BLK_DEV_RAM=y
 CONFIG_BLK_DEV_RAM_SIZE=131072
-CONFIG_MISC_DEVICES=y
 CONFIG_EEPROM_LEGACY=y
 CONFIG_BLK_DEV_SD=y
 CONFIG_CHR_DEV_ST=y
@@ -137,7 +128,6 @@
 CONFIG_SERIAL_8250_CONSOLE=y
 CONFIG_SERIAL_8250_NR_UARTS=2
 CONFIG_SERIAL_8250_RUNTIME_UARTS=2
-CONFIG_SERIAL_8250_EXTENDED=y
 CONFIG_SERIAL_8250_MANY_PORTS=y
 CONFIG_SERIAL_8250_DETECT_IRQ=y
 CONFIG_SERIAL_8250_RSA=y
@@ -186,7 +176,6 @@
 CONFIG_HID_SONY=y
 CONFIG_HID_SUNPLUS=y
 CONFIG_USB=y
-CONFIG_USB_DEVICEFS=y
 CONFIG_USB_MON=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_FSL=y
@@ -232,18 +221,13 @@
 CONFIG_SYSV_FS=m
 CONFIG_UFS_FS=m
 CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
 CONFIG_NFS_V4=y
 CONFIG_ROOT_NFS=y
 CONFIG_NFSD=y
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_MAC_PARTITION=y
 CONFIG_CRC_T10DIF=y
 CONFIG_DEBUG_FS=y
 CONFIG_DETECT_HUNG_TASK=y
 CONFIG_DEBUG_INFO=y
-CONFIG_SYSCTL_SYSCALL_CHECK=y
-CONFIG_IRQ_DOMAIN_DEBUG=y
 CONFIG_CRYPTO_PCBC=m
 CONFIG_CRYPTO_SHA256=y
 CONFIG_CRYPTO_SHA512=y
diff --git a/arch/powerpc/include/asm/cputable.h b/arch/powerpc/include/asm/cputable.h
index 50d82c8..b3c083d 100644
--- a/arch/powerpc/include/asm/cputable.h
+++ b/arch/powerpc/include/asm/cputable.h
@@ -553,9 +553,7 @@
 		& feature);
 }
 
-#ifdef CONFIG_HAVE_HW_BREAKPOINT
 #define HBP_NUM 1
-#endif /* CONFIG_HAVE_HW_BREAKPOINT */
 
 #endif /* !__ASSEMBLY__ */
 
diff --git a/arch/powerpc/include/asm/kvm_host.h b/arch/powerpc/include/asm/kvm_host.h
index 50ea12f..a8bf5c6 100644
--- a/arch/powerpc/include/asm/kvm_host.h
+++ b/arch/powerpc/include/asm/kvm_host.h
@@ -33,6 +33,7 @@
 #include <asm/kvm_asm.h>
 #include <asm/processor.h>
 #include <asm/page.h>
+#include <asm/cacheflush.h>
 
 #define KVM_MAX_VCPUS		NR_CPUS
 #define KVM_MAX_VCORES		NR_CPUS
diff --git a/arch/powerpc/include/asm/kvm_ppc.h b/arch/powerpc/include/asm/kvm_ppc.h
index 0124937..e006f0b 100644
--- a/arch/powerpc/include/asm/kvm_ppc.h
+++ b/arch/powerpc/include/asm/kvm_ppc.h
@@ -219,4 +219,16 @@
 void kvmppc_free_lpid(long lpid);
 void kvmppc_init_lpid(unsigned long nr_lpids);
 
+static inline void kvmppc_mmu_flush_icache(pfn_t pfn)
+{
+	/* Clear i-cache for new pages */
+	struct page *page;
+	page = pfn_to_page(pfn);
+	if (!test_bit(PG_arch_1, &page->flags)) {
+		flush_dcache_icache_page(page);
+		set_bit(PG_arch_1, &page->flags);
+	}
+}
+
+
 #endif /* __POWERPC_KVM_PPC_H__ */
diff --git a/arch/powerpc/include/asm/mpic_msgr.h b/arch/powerpc/include/asm/mpic_msgr.h
index 326d33c..d4f471f 100644
--- a/arch/powerpc/include/asm/mpic_msgr.h
+++ b/arch/powerpc/include/asm/mpic_msgr.h
@@ -14,6 +14,7 @@
 #include <linux/types.h>
 #include <linux/spinlock.h>
 #include <asm/smp.h>
+#include <asm/io.h>
 
 struct mpic_msgr {
 	u32 __iomem *base;
diff --git a/arch/powerpc/include/asm/processor.h b/arch/powerpc/include/asm/processor.h
index 53b6dfa..54b73a2 100644
--- a/arch/powerpc/include/asm/processor.h
+++ b/arch/powerpc/include/asm/processor.h
@@ -386,6 +386,7 @@
 enum idle_boot_override {IDLE_NO_OVERRIDE = 0, IDLE_POWERSAVE_OFF};
 
 extern int powersave_nap;	/* set if nap mode can be used in idle loop */
+extern void power7_nap(void);
 
 #ifdef CONFIG_PSERIES_IDLE
 extern void update_smt_snooze_delay(int snooze);
diff --git a/arch/powerpc/kernel/asm-offsets.c b/arch/powerpc/kernel/asm-offsets.c
index 85b05c4..e899572 100644
--- a/arch/powerpc/kernel/asm-offsets.c
+++ b/arch/powerpc/kernel/asm-offsets.c
@@ -76,6 +76,7 @@
 	DEFINE(SIGSEGV, SIGSEGV);
 	DEFINE(NMI_MASK, NMI_MASK);
 	DEFINE(THREAD_DSCR, offsetof(struct thread_struct, dscr));
+	DEFINE(THREAD_DSCR_INHERIT, offsetof(struct thread_struct, dscr_inherit));
 #else
 	DEFINE(THREAD_INFO, offsetof(struct task_struct, stack));
 #endif /* CONFIG_PPC64 */
diff --git a/arch/powerpc/kernel/dbell.c b/arch/powerpc/kernel/dbell.c
index 5b25c80..a892680 100644
--- a/arch/powerpc/kernel/dbell.c
+++ b/arch/powerpc/kernel/dbell.c
@@ -28,6 +28,8 @@
 
 void doorbell_cause_ipi(int cpu, unsigned long data)
 {
+	/* Order previous accesses vs. msgsnd, which is treated as a store */
+	mb();
 	ppc_msgsnd(PPC_DBELL, 0, data);
 }
 
diff --git a/arch/powerpc/kernel/dma-iommu.c b/arch/powerpc/kernel/dma-iommu.c
index 2d7bb8c..e489752 100644
--- a/arch/powerpc/kernel/dma-iommu.c
+++ b/arch/powerpc/kernel/dma-iommu.c
@@ -83,11 +83,10 @@
 		return 0;
 	}
 
-	if ((tbl->it_offset + tbl->it_size) > (mask >> IOMMU_PAGE_SHIFT)) {
-		dev_info(dev, "Warning: IOMMU window too big for device mask\n");
-		dev_info(dev, "mask: 0x%08llx, table end: 0x%08lx\n",
-				mask, (tbl->it_offset + tbl->it_size) <<
-				IOMMU_PAGE_SHIFT);
+	if (tbl->it_offset > (mask >> IOMMU_PAGE_SHIFT)) {
+		dev_info(dev, "Warning: IOMMU offset too big for device mask\n");
+		dev_info(dev, "mask: 0x%08llx, table offset: 0x%08lx\n",
+				mask, tbl->it_offset << IOMMU_PAGE_SHIFT);
 		return 0;
 	} else
 		return 1;
diff --git a/arch/powerpc/kernel/entry_64.S b/arch/powerpc/kernel/entry_64.S
index 4b01a25..b40e0b4 100644
--- a/arch/powerpc/kernel/entry_64.S
+++ b/arch/powerpc/kernel/entry_64.S
@@ -370,6 +370,12 @@
 	li	r3,0
 	b	syscall_exit
 
+	.section	".toc","aw"
+DSCR_DEFAULT:
+	.tc dscr_default[TC],dscr_default
+
+	.section	".text"
+
 /*
  * This routine switches between two different tasks.  The process
  * state of one is saved on its kernel stack.  Then the state
@@ -509,9 +515,6 @@
 	mr	r1,r8		/* start using new stack pointer */
 	std	r7,PACAKSAVE(r13)
 
-	ld	r6,_CCR(r1)
-	mtcrf	0xFF,r6
-
 #ifdef CONFIG_ALTIVEC
 BEGIN_FTR_SECTION
 	ld	r0,THREAD_VRSAVE(r4)
@@ -520,14 +523,22 @@
 #endif /* CONFIG_ALTIVEC */
 #ifdef CONFIG_PPC64
 BEGIN_FTR_SECTION
+	lwz	r6,THREAD_DSCR_INHERIT(r4)
+	ld	r7,DSCR_DEFAULT@toc(2)
 	ld	r0,THREAD_DSCR(r4)
-	cmpd	r0,r25
-	beq	1f
+	cmpwi	r6,0
+	bne	1f
+	ld	r0,0(r7)
+1:	cmpd	r0,r25
+	beq	2f
 	mtspr	SPRN_DSCR,r0
-1:	
+2:
 END_FTR_SECTION_IFSET(CPU_FTR_DSCR)
 #endif
 
+	ld	r6,_CCR(r1)
+	mtcrf	0xFF,r6
+
 	/* r3-r13 are destroyed -- Cort */
 	REST_8GPRS(14, r1)
 	REST_10GPRS(22, r1)
diff --git a/arch/powerpc/kernel/exceptions-64s.S b/arch/powerpc/kernel/exceptions-64s.S
index e894515..39aa97d 100644
--- a/arch/powerpc/kernel/exceptions-64s.S
+++ b/arch/powerpc/kernel/exceptions-64s.S
@@ -186,7 +186,7 @@
 	KVM_HANDLER_PR(PACA_EXGEN, EXC_STD, 0x800)
 
 	MASKABLE_EXCEPTION_PSERIES(0x900, 0x900, decrementer)
-	MASKABLE_EXCEPTION_HV(0x980, 0x982, decrementer)
+	STD_EXCEPTION_HV(0x980, 0x982, hdecrementer)
 
 	STD_EXCEPTION_PSERIES(0xa00, 0xa00, trap_0a)
 	KVM_HANDLER_PR(PACA_EXGEN, EXC_STD, 0xa00)
@@ -486,6 +486,7 @@
 
 	STD_EXCEPTION_COMMON_ASYNC(0x500, hardware_interrupt, do_IRQ)
 	STD_EXCEPTION_COMMON_ASYNC(0x900, decrementer, .timer_interrupt)
+	STD_EXCEPTION_COMMON(0x980, hdecrementer, .hdec_interrupt)
 	STD_EXCEPTION_COMMON(0xa00, trap_0a, .unknown_exception)
 	STD_EXCEPTION_COMMON(0xb00, trap_0b, .unknown_exception)
 	STD_EXCEPTION_COMMON(0xd00, single_step, .single_step_exception)
diff --git a/arch/powerpc/kernel/hw_breakpoint.c b/arch/powerpc/kernel/hw_breakpoint.c
index f3a82dd..956a4c4 100644
--- a/arch/powerpc/kernel/hw_breakpoint.c
+++ b/arch/powerpc/kernel/hw_breakpoint.c
@@ -253,7 +253,7 @@
 
 	/* Do not emulate user-space instructions, instead single-step them */
 	if (user_mode(regs)) {
-		bp->ctx->task->thread.last_hit_ubp = bp;
+		current->thread.last_hit_ubp = bp;
 		regs->msr |= MSR_SE;
 		goto out;
 	}
diff --git a/arch/powerpc/kernel/idle_power7.S b/arch/powerpc/kernel/idle_power7.S
index 7140d83..e11863f 100644
--- a/arch/powerpc/kernel/idle_power7.S
+++ b/arch/powerpc/kernel/idle_power7.S
@@ -28,7 +28,9 @@
 	lwz	r4,ADDROFF(powersave_nap)(r3)
 	cmpwi	0,r4,0
 	beqlr
+	/* fall through */
 
+_GLOBAL(power7_nap)
 	/* NAP is a state loss, we create a regs frame on the
 	 * stack, fill it up with the state we care about and
 	 * stick a pointer to it in PACAR1. We really only
diff --git a/arch/powerpc/kernel/kgdb.c b/arch/powerpc/kernel/kgdb.c
index 782bd0a..c470a40 100644
--- a/arch/powerpc/kernel/kgdb.c
+++ b/arch/powerpc/kernel/kgdb.c
@@ -25,6 +25,7 @@
 #include <asm/processor.h>
 #include <asm/machdep.h>
 #include <asm/debug.h>
+#include <linux/slab.h>
 
 /*
  * This table contains the mapping between PowerPC hardware trap types, and
@@ -101,6 +102,21 @@
 	return SIGHUP;		/* default for things we don't know about */
 }
 
+/**
+ *
+ *	kgdb_skipexception - Bail out of KGDB when we've been triggered.
+ *	@exception: Exception vector number
+ *	@regs: Current &struct pt_regs.
+ *
+ *	On some architectures we need to skip a breakpoint exception when
+ *	it occurs after a breakpoint has been removed.
+ *
+ */
+int kgdb_skipexception(int exception, struct pt_regs *regs)
+{
+	return kgdb_isremovedbreak(regs->nip);
+}
+
 static int kgdb_call_nmi_hook(struct pt_regs *regs)
 {
 	kgdb_nmicallback(raw_smp_processor_id(), regs);
@@ -138,6 +154,8 @@
 static int kgdb_singlestep(struct pt_regs *regs)
 {
 	struct thread_info *thread_info, *exception_thread_info;
+	struct thread_info *backup_current_thread_info = \
+		(struct thread_info *)kmalloc(sizeof(struct thread_info), GFP_KERNEL);
 
 	if (user_mode(regs))
 		return 0;
@@ -155,13 +173,17 @@
 	thread_info = (struct thread_info *)(regs->gpr[1] & ~(THREAD_SIZE-1));
 	exception_thread_info = current_thread_info();
 
-	if (thread_info != exception_thread_info)
+	if (thread_info != exception_thread_info) {
+		/* Save the original current_thread_info. */
+		memcpy(backup_current_thread_info, exception_thread_info, sizeof *thread_info);
 		memcpy(exception_thread_info, thread_info, sizeof *thread_info);
+	}
 
 	kgdb_handle_exception(0, SIGTRAP, 0, regs);
 
 	if (thread_info != exception_thread_info)
-		memcpy(thread_info, exception_thread_info, sizeof *thread_info);
+		/* Restore current_thread_info lastly. */
+		memcpy(exception_thread_info, backup_current_thread_info, sizeof *thread_info);
 
 	return 1;
 }
@@ -410,7 +432,6 @@
 #else
 			linux_regs->msr |= MSR_SE;
 #endif
-			kgdb_single_step = 1;
 			atomic_set(&kgdb_cpu_doing_single_step,
 				   raw_smp_processor_id());
 		}
diff --git a/arch/powerpc/kernel/process.c b/arch/powerpc/kernel/process.c
index 710f400..1a1f2dd 100644
--- a/arch/powerpc/kernel/process.c
+++ b/arch/powerpc/kernel/process.c
@@ -802,16 +802,8 @@
 #endif /* CONFIG_PPC_STD_MMU_64 */
 #ifdef CONFIG_PPC64 
 	if (cpu_has_feature(CPU_FTR_DSCR)) {
-		if (current->thread.dscr_inherit) {
-			p->thread.dscr_inherit = 1;
-			p->thread.dscr = current->thread.dscr;
-		} else if (0 != dscr_default) {
-			p->thread.dscr_inherit = 1;
-			p->thread.dscr = dscr_default;
-		} else {
-			p->thread.dscr_inherit = 0;
-			p->thread.dscr = 0;
-		}
+		p->thread.dscr_inherit = current->thread.dscr_inherit;
+		p->thread.dscr = current->thread.dscr;
 	}
 #endif
 
diff --git a/arch/powerpc/kernel/smp.c b/arch/powerpc/kernel/smp.c
index 0321007..8d4214a 100644
--- a/arch/powerpc/kernel/smp.c
+++ b/arch/powerpc/kernel/smp.c
@@ -198,8 +198,15 @@
 	struct cpu_messages *info = &per_cpu(ipi_message, cpu);
 	char *message = (char *)&info->messages;
 
+	/*
+	 * Order previous accesses before accesses in the IPI handler.
+	 */
+	smp_mb();
 	message[msg] = 1;
-	mb();
+	/*
+	 * cause_ipi functions are required to include a full barrier
+	 * before doing whatever causes the IPI.
+	 */
 	smp_ops->cause_ipi(cpu, info->data);
 }
 
@@ -211,7 +218,7 @@
 	mb();	/* order any irq clear */
 
 	do {
-		all = xchg_local(&info->messages, 0);
+		all = xchg(&info->messages, 0);
 
 #ifdef __BIG_ENDIAN
 		if (all & (1 << (24 - 8 * PPC_MSG_CALL_FUNCTION)))
diff --git a/arch/powerpc/kernel/syscalls.c b/arch/powerpc/kernel/syscalls.c
index f2496f2..4e3cc47 100644
--- a/arch/powerpc/kernel/syscalls.c
+++ b/arch/powerpc/kernel/syscalls.c
@@ -107,11 +107,11 @@
 	long ret;
 
 	if (personality(current->personality) == PER_LINUX32
-	    && personality == PER_LINUX)
-		personality = PER_LINUX32;
+	    && personality(personality) == PER_LINUX)
+		personality = (personality & ~PER_MASK) | PER_LINUX32;
 	ret = sys_personality(personality);
-	if (ret == PER_LINUX32)
-		ret = PER_LINUX;
+	if (personality(ret) == PER_LINUX32)
+		ret = (ret & ~PER_MASK) | PER_LINUX;
 	return ret;
 }
 #endif
diff --git a/arch/powerpc/kernel/sysfs.c b/arch/powerpc/kernel/sysfs.c
index 3529446..8302af6 100644
--- a/arch/powerpc/kernel/sysfs.c
+++ b/arch/powerpc/kernel/sysfs.c
@@ -194,6 +194,14 @@
 	return sprintf(buf, "%lx\n", dscr_default);
 }
 
+static void update_dscr(void *dummy)
+{
+	if (!current->thread.dscr_inherit) {
+		current->thread.dscr = dscr_default;
+		mtspr(SPRN_DSCR, dscr_default);
+	}
+}
+
 static ssize_t __used store_dscr_default(struct device *dev,
 		struct device_attribute *attr, const char *buf,
 		size_t count)
@@ -206,6 +214,8 @@
 		return -EINVAL;
 	dscr_default = val;
 
+	on_each_cpu(update_dscr, NULL, 1);
+
 	return count;
 }
 
diff --git a/arch/powerpc/kernel/time.c b/arch/powerpc/kernel/time.c
index be171ee..e49e931 100644
--- a/arch/powerpc/kernel/time.c
+++ b/arch/powerpc/kernel/time.c
@@ -535,6 +535,15 @@
 	trace_timer_interrupt_exit(regs);
 }
 
+/*
+ * Hypervisor decrementer interrupts shouldn't occur but are sometimes
+ * left pending on exit from a KVM guest.  We don't need to do anything
+ * to clear them, as they are edge-triggered.
+ */
+void hdec_interrupt(struct pt_regs *regs)
+{
+}
+
 #ifdef CONFIG_SUSPEND
 static void generic_suspend_disable_irqs(void)
 {
diff --git a/arch/powerpc/kernel/traps.c b/arch/powerpc/kernel/traps.c
index 1589723..ae0843f 100644
--- a/arch/powerpc/kernel/traps.c
+++ b/arch/powerpc/kernel/traps.c
@@ -972,8 +972,9 @@
 			cpu_has_feature(CPU_FTR_DSCR)) {
 		PPC_WARN_EMULATED(mtdscr, regs);
 		rd = (instword >> 21) & 0x1f;
-		mtspr(SPRN_DSCR, regs->gpr[rd]);
+		current->thread.dscr = regs->gpr[rd];
 		current->thread.dscr_inherit = 1;
+		mtspr(SPRN_DSCR, current->thread.dscr);
 		return 0;
 	}
 #endif
diff --git a/arch/powerpc/kvm/book3s_32_mmu_host.c b/arch/powerpc/kvm/book3s_32_mmu_host.c
index f922c29..837f13e 100644
--- a/arch/powerpc/kvm/book3s_32_mmu_host.c
+++ b/arch/powerpc/kvm/book3s_32_mmu_host.c
@@ -211,6 +211,9 @@
 		pteg1 |= PP_RWRX;
 	}
 
+	if (orig_pte->may_execute)
+		kvmppc_mmu_flush_icache(hpaddr >> PAGE_SHIFT);
+
 	local_irq_disable();
 
 	if (pteg[rr]) {
diff --git a/arch/powerpc/kvm/book3s_64_mmu_host.c b/arch/powerpc/kvm/book3s_64_mmu_host.c
index 10fc8ec..0688b6b 100644
--- a/arch/powerpc/kvm/book3s_64_mmu_host.c
+++ b/arch/powerpc/kvm/book3s_64_mmu_host.c
@@ -126,6 +126,8 @@
 
 	if (!orig_pte->may_execute)
 		rflags |= HPTE_R_N;
+	else
+		kvmppc_mmu_flush_icache(hpaddr >> PAGE_SHIFT);
 
 	hash = hpt_hash(va, PTE_SIZE, MMU_SEGSIZE_256M);
 
diff --git a/arch/powerpc/kvm/book3s_hv_rmhandlers.S b/arch/powerpc/kvm/book3s_hv_rmhandlers.S
index 5a84c8d..44b72fe 100644
--- a/arch/powerpc/kvm/book3s_hv_rmhandlers.S
+++ b/arch/powerpc/kvm/book3s_hv_rmhandlers.S
@@ -1421,13 +1421,13 @@
 	sync			/* order setting ceded vs. testing prodded */
 	lbz	r5,VCPU_PRODDED(r3)
 	cmpwi	r5,0
-	bne	1f
+	bne	kvm_cede_prodded
 	li	r0,0		/* set trap to 0 to say hcall is handled */
 	stw	r0,VCPU_TRAP(r3)
 	li	r0,H_SUCCESS
 	std	r0,VCPU_GPR(R3)(r3)
 BEGIN_FTR_SECTION
-	b	2f		/* just send it up to host on 970 */
+	b	kvm_cede_exit	/* just send it up to host on 970 */
 END_FTR_SECTION_IFCLR(CPU_FTR_ARCH_206)
 
 	/*
@@ -1446,7 +1446,7 @@
 	or	r4,r4,r0
 	PPC_POPCNTW(R7,R4)
 	cmpw	r7,r8
-	bge	2f
+	bge	kvm_cede_exit
 	stwcx.	r4,0,r6
 	bne	31b
 	li	r0,1
@@ -1555,7 +1555,8 @@
 	b	hcall_real_fallback
 
 	/* cede when already previously prodded case */
-1:	li	r0,0
+kvm_cede_prodded:
+	li	r0,0
 	stb	r0,VCPU_PRODDED(r3)
 	sync			/* order testing prodded vs. clearing ceded */
 	stb	r0,VCPU_CEDED(r3)
@@ -1563,7 +1564,8 @@
 	blr
 
 	/* we've ceded but we want to give control to the host */
-2:	li	r3,H_TOO_HARD
+kvm_cede_exit:
+	li	r3,H_TOO_HARD
 	blr
 
 secondary_too_late:
diff --git a/arch/powerpc/kvm/e500_tlb.c b/arch/powerpc/kvm/e500_tlb.c
index c510fc9..a2b6671 100644
--- a/arch/powerpc/kvm/e500_tlb.c
+++ b/arch/powerpc/kvm/e500_tlb.c
@@ -322,11 +322,11 @@
 static void clear_tlb1_bitmap(struct kvmppc_vcpu_e500 *vcpu_e500)
 {
 	if (vcpu_e500->g2h_tlb1_map)
-		memset(vcpu_e500->g2h_tlb1_map,
-		       sizeof(u64) * vcpu_e500->gtlb_params[1].entries, 0);
+		memset(vcpu_e500->g2h_tlb1_map, 0,
+		       sizeof(u64) * vcpu_e500->gtlb_params[1].entries);
 	if (vcpu_e500->h2g_tlb1_rmap)
-		memset(vcpu_e500->h2g_tlb1_rmap,
-		       sizeof(unsigned int) * host_tlb_params[1].entries, 0);
+		memset(vcpu_e500->h2g_tlb1_rmap, 0,
+		       sizeof(unsigned int) * host_tlb_params[1].entries);
 }
 
 static void clear_tlb_privs(struct kvmppc_vcpu_e500 *vcpu_e500)
@@ -539,6 +539,9 @@
 
 	kvmppc_e500_setup_stlbe(&vcpu_e500->vcpu, gtlbe, tsize,
 				ref, gvaddr, stlbe);
+
+	/* Clear i-cache for new pages */
+	kvmppc_mmu_flush_icache(pfn);
 }
 
 /* XXX only map the one-one case, for now use TLB0 */
diff --git a/arch/powerpc/lib/code-patching.c b/arch/powerpc/lib/code-patching.c
index dd223b3..17e5b23 100644
--- a/arch/powerpc/lib/code-patching.c
+++ b/arch/powerpc/lib/code-patching.c
@@ -20,7 +20,7 @@
 {
 	int err;
 
-	err = __put_user(instr, addr);
+	__put_user_size(instr, addr, 4, err);
 	if (err)
 		return err;
 	asm ("dcbst 0, %0; sync; icbi 0,%0; sync; isync" : : "r" (addr));
diff --git a/arch/powerpc/lib/copyuser_power7.S b/arch/powerpc/lib/copyuser_power7.S
index f9ede7c..0d24ff1 100644
--- a/arch/powerpc/lib/copyuser_power7.S
+++ b/arch/powerpc/lib/copyuser_power7.S
@@ -288,7 +288,7 @@
 	std	r0,16(r1)
 	stdu	r1,-STACKFRAMESIZE(r1)
 	bl	.enter_vmx_usercopy
-	cmpwi	r3,0
+	cmpwi	cr1,r3,0
 	ld	r0,STACKFRAMESIZE+16(r1)
 	ld	r3,STACKFRAMESIZE+48(r1)
 	ld	r4,STACKFRAMESIZE+56(r1)
@@ -326,38 +326,7 @@
 	dcbt	r0,r8,0b01010	/* GO */
 .machine pop
 
-	/*
-	 * We prefetch both the source and destination using enhanced touch
-	 * instructions. We use a stream ID of 0 for the load side and
-	 * 1 for the store side.
-	 */
-	clrrdi	r6,r4,7
-	clrrdi	r9,r3,7
-	ori	r9,r9,1		/* stream=1 */
-
-	srdi	r7,r5,7		/* length in cachelines, capped at 0x3FF */
-	cmpldi	cr1,r7,0x3FF
-	ble	cr1,1f
-	li	r7,0x3FF
-1:	lis	r0,0x0E00	/* depth=7 */
-	sldi	r7,r7,7
-	or	r7,r7,r0
-	ori	r10,r7,1	/* stream=1 */
-
-	lis	r8,0x8000	/* GO=1 */
-	clrldi	r8,r8,32
-
-.machine push
-.machine "power4"
-	dcbt	r0,r6,0b01000
-	dcbt	r0,r7,0b01010
-	dcbtst	r0,r9,0b01000
-	dcbtst	r0,r10,0b01010
-	eieio
-	dcbt	r0,r8,0b01010	/* GO */
-.machine pop
-
-	beq	.Lunwind_stack_nonvmx_copy
+	beq	cr1,.Lunwind_stack_nonvmx_copy
 
 	/*
 	 * If source and destination are not relatively aligned we use a
diff --git a/arch/powerpc/lib/memcpy_power7.S b/arch/powerpc/lib/memcpy_power7.S
index 0efdc51..7ba6c96 100644
--- a/arch/powerpc/lib/memcpy_power7.S
+++ b/arch/powerpc/lib/memcpy_power7.S
@@ -222,7 +222,7 @@
 	std	r0,16(r1)
 	stdu	r1,-STACKFRAMESIZE(r1)
 	bl	.enter_vmx_copy
-	cmpwi	r3,0
+	cmpwi	cr1,r3,0
 	ld	r0,STACKFRAMESIZE+16(r1)
 	ld	r3,STACKFRAMESIZE+48(r1)
 	ld	r4,STACKFRAMESIZE+56(r1)
@@ -260,7 +260,7 @@
 	dcbt	r0,r8,0b01010	/* GO */
 .machine pop
 
-	beq	.Lunwind_stack_nonvmx_copy
+	beq	cr1,.Lunwind_stack_nonvmx_copy
 
 	/*
 	 * If source and destination are not relatively aligned we use a
diff --git a/arch/powerpc/mm/mem.c b/arch/powerpc/mm/mem.c
index baaafde..fbdad0e 100644
--- a/arch/powerpc/mm/mem.c
+++ b/arch/powerpc/mm/mem.c
@@ -469,6 +469,7 @@
 	__flush_dcache_icache_phys(page_to_pfn(page) << PAGE_SHIFT);
 #endif
 }
+EXPORT_SYMBOL(flush_dcache_icache_page);
 
 void clear_user_page(void *page, unsigned long vaddr, struct page *pg)
 {
diff --git a/arch/powerpc/mm/numa.c b/arch/powerpc/mm/numa.c
index 39b1597..59213cf 100644
--- a/arch/powerpc/mm/numa.c
+++ b/arch/powerpc/mm/numa.c
@@ -1436,11 +1436,11 @@
 
 /*
  * Update the node maps and sysfs entries for each cpu whose home node
- * has changed.
+ * has changed. Returns 1 when the topology has changed, and 0 otherwise.
  */
 int arch_update_cpu_topology(void)
 {
-	int cpu, nid, old_nid;
+	int cpu, nid, old_nid, changed = 0;
 	unsigned int associativity[VPHN_ASSOC_BUFSIZE] = {0};
 	struct device *dev;
 
@@ -1466,9 +1466,10 @@
 		dev = get_cpu_device(cpu);
 		if (dev)
 			kobject_uevent(&dev->kobj, KOBJ_CHANGE);
+		changed = 1;
 	}
 
-	return 1;
+	return changed;
 }
 
 static void topology_work_fn(struct work_struct *work)
diff --git a/arch/powerpc/perf/core-book3s.c b/arch/powerpc/perf/core-book3s.c
index 77b49dd..7cd2dbd 100644
--- a/arch/powerpc/perf/core-book3s.c
+++ b/arch/powerpc/perf/core-book3s.c
@@ -1431,7 +1431,7 @@
 		if (!event->hw.idx || is_limited_pmc(event->hw.idx))
 			continue;
 		val = read_pmc(event->hw.idx);
-		if ((int)val < 0) {
+		if (pmc_overflow(val)) {
 			/* event has overflowed */
 			found = 1;
 			record_and_restart(event, val, regs);
diff --git a/arch/powerpc/platforms/powernv/smp.c b/arch/powerpc/platforms/powernv/smp.c
index 3ef4625..7698b6e 100644
--- a/arch/powerpc/platforms/powernv/smp.c
+++ b/arch/powerpc/platforms/powernv/smp.c
@@ -106,14 +106,6 @@
 {
 	unsigned int cpu;
 
-	/* If powersave_nap is enabled, use NAP mode, else just
-	 * spin aimlessly
-	 */
-	if (!powersave_nap) {
-		generic_mach_cpu_die();
-		return;
-	}
-
 	/* Standard hot unplug procedure */
 	local_irq_disable();
 	idle_task_exit();
@@ -128,7 +120,7 @@
 	 */
 	mtspr(SPRN_LPCR, mfspr(SPRN_LPCR) & ~(u64)LPCR_PECE1);
 	while (!generic_check_cpu_restart(cpu)) {
-		power7_idle();
+		power7_nap();
 		if (!generic_check_cpu_restart(cpu)) {
 			DBG("CPU%d Unexpected exit while offline !\n", cpu);
 			/* We may be getting an IPI, so we re-enable
diff --git a/arch/powerpc/sysdev/fsl_pci.c b/arch/powerpc/sysdev/fsl_pci.c
index a7b2a60..c37f461 100644
--- a/arch/powerpc/sysdev/fsl_pci.c
+++ b/arch/powerpc/sysdev/fsl_pci.c
@@ -465,7 +465,7 @@
 			iounmap(hose->cfg_data);
 		iounmap(hose->cfg_addr);
 		pcibios_free_controller(hose);
-		return 0;
+		return -ENODEV;
 	}
 
 	setup_pci_cmd(hose);
@@ -827,6 +827,7 @@
 
 void __devinit fsl_pci_init(void)
 {
+	int ret;
 	struct device_node *node;
 	struct pci_controller *hose;
 	dma_addr_t max = 0xffffffff;
@@ -855,10 +856,12 @@
 			if (!fsl_pci_primary)
 				fsl_pci_primary = node;
 
-			fsl_add_bridge(node, fsl_pci_primary == node);
-			hose = pci_find_hose_for_OF_device(node);
-			max = min(max, hose->dma_window_base_cur +
-					hose->dma_window_size);
+			ret = fsl_add_bridge(node, fsl_pci_primary == node);
+			if (ret == 0) {
+				hose = pci_find_hose_for_OF_device(node);
+				max = min(max, hose->dma_window_base_cur +
+						hose->dma_window_size);
+			}
 		}
 	}
 
diff --git a/arch/powerpc/sysdev/mpic_msgr.c b/arch/powerpc/sysdev/mpic_msgr.c
index 483d8fa..e961f8c 100644
--- a/arch/powerpc/sysdev/mpic_msgr.c
+++ b/arch/powerpc/sysdev/mpic_msgr.c
@@ -14,6 +14,9 @@
 #include <linux/list.h>
 #include <linux/of_platform.h>
 #include <linux/errno.h>
+#include <linux/err.h>
+#include <linux/export.h>
+#include <linux/slab.h>
 #include <asm/prom.h>
 #include <asm/hw_irq.h>
 #include <asm/ppc-pci.h>
diff --git a/arch/powerpc/sysdev/xics/icp-hv.c b/arch/powerpc/sysdev/xics/icp-hv.c
index 14469cf..df0fc58 100644
--- a/arch/powerpc/sysdev/xics/icp-hv.c
+++ b/arch/powerpc/sysdev/xics/icp-hv.c
@@ -65,7 +65,11 @@
 static inline void icp_hv_set_qirr(int n_cpu , u8 value)
 {
 	int hw_cpu = get_hard_smp_processor_id(n_cpu);
-	long rc = plpar_hcall_norets(H_IPI, hw_cpu, value);
+	long rc;
+
+	/* Make sure all previous accesses are ordered before IPI sending */
+	mb();
+	rc = plpar_hcall_norets(H_IPI, hw_cpu, value);
 	if (rc != H_SUCCESS) {
 		pr_err("%s: bad return code qirr cpu=%d hw_cpu=%d mfrr=0x%x "
 			"returned %ld\n", __func__, n_cpu, hw_cpu, value, rc);
diff --git a/arch/powerpc/xmon/xmon.c b/arch/powerpc/xmon/xmon.c
index eab3492..9b49c65e 100644
--- a/arch/powerpc/xmon/xmon.c
+++ b/arch/powerpc/xmon/xmon.c
@@ -17,6 +17,7 @@
 #include <linux/reboot.h>
 #include <linux/delay.h>
 #include <linux/kallsyms.h>
+#include <linux/kmsg_dump.h>
 #include <linux/cpumask.h>
 #include <linux/export.h>
 #include <linux/sysrq.h>
@@ -894,13 +895,13 @@
 #endif
 		default:
 			printf("Unrecognized command: ");
-		        do {
+			do {
 				if (' ' < cmd && cmd <= '~')
 					putchar(cmd);
 				else
 					printf("\\x%x", cmd);
 				cmd = inchar();
-		        } while (cmd != '\n'); 
+			} while (cmd != '\n');
 			printf(" (type ? for help)\n");
 			break;
 		}
@@ -1097,7 +1098,7 @@
 	return 1;
 }
 
-static char *breakpoint_help_string = 
+static char *breakpoint_help_string =
     "Breakpoint command usage:\n"
     "b                show breakpoints\n"
     "b <addr> [cnt]   set breakpoint at given instr addr\n"
@@ -1193,7 +1194,7 @@
 
 	default:
 		termch = cmd;
-	        cmd = skipbl();
+		cmd = skipbl();
 		if (cmd == '?') {
 			printf(breakpoint_help_string);
 			break;
@@ -1359,7 +1360,7 @@
 				       sp + REGS_OFFSET);
 				break;
 			}
-                        printf("--- Exception: %lx %s at ", regs.trap,
+			printf("--- Exception: %lx %s at ", regs.trap,
 			       getvecname(TRAP(&regs)));
 			pc = regs.nip;
 			lr = regs.link;
@@ -1623,14 +1624,14 @@
 
 	cmd = skipbl();
 	if (cmd == '\n') {
-	        unsigned long sp, toc;
+		unsigned long sp, toc;
 		asm("mr %0,1" : "=r" (sp) :);
 		asm("mr %0,2" : "=r" (toc) :);
 
 		printf("msr  = "REG"  sprg0= "REG"\n",
 		       mfmsr(), mfspr(SPRN_SPRG0));
 		printf("pvr  = "REG"  sprg1= "REG"\n",
-		       mfspr(SPRN_PVR), mfspr(SPRN_SPRG1)); 
+		       mfspr(SPRN_PVR), mfspr(SPRN_SPRG1));
 		printf("dec  = "REG"  sprg2= "REG"\n",
 		       mfspr(SPRN_DEC), mfspr(SPRN_SPRG2));
 		printf("sp   = "REG"  sprg3= "REG"\n", sp, mfspr(SPRN_SPRG3));
@@ -1783,7 +1784,7 @@
 static int brev;
 static int mnoread;
 
-static char *memex_help_string = 
+static char *memex_help_string =
     "Memory examine command usage:\n"
     "m [addr] [flags] examine/change memory\n"
     "  addr is optional.  will start where left off.\n"
@@ -1798,7 +1799,7 @@
     "NOTE: flags are saved as defaults\n"
     "";
 
-static char *memex_subcmd_help_string = 
+static char *memex_subcmd_help_string =
     "Memory examine subcommands:\n"
     "  hexval   write this val to current location\n"
     "  'string' write chars from string to this location\n"
@@ -2064,7 +2065,7 @@
 		nr = mread(adrs, temp, r);
 		adrs += nr;
 		for (m = 0; m < r; ++m) {
-		        if ((m & (sizeof(long) - 1)) == 0 && m > 0)
+			if ((m & (sizeof(long) - 1)) == 0 && m > 0)
 				putchar(' ');
 			if (m < nr)
 				printf("%.2x", temp[m]);
@@ -2072,7 +2073,7 @@
 				printf("%s", fault_chars[fault_type]);
 		}
 		for (; m < 16; ++m) {
-		        if ((m & (sizeof(long) - 1)) == 0)
+			if ((m & (sizeof(long) - 1)) == 0)
 				putchar(' ');
 			printf("  ");
 		}
@@ -2148,45 +2149,28 @@
 void
 dump_log_buf(void)
 {
-        const unsigned long size = 128;
-        unsigned long end, addr;
-        unsigned char buf[size + 1];
+	struct kmsg_dumper dumper = { .active = 1 };
+	unsigned char buf[128];
+	size_t len;
 
-        addr = 0;
-        buf[size] = '\0';
+	if (setjmp(bus_error_jmp) != 0) {
+		printf("Error dumping printk buffer!\n");
+		return;
+	}
 
-        if (setjmp(bus_error_jmp) != 0) {
-                printf("Unable to lookup symbol __log_buf!\n");
-                return;
-        }
+	catch_memory_errors = 1;
+	sync();
 
-        catch_memory_errors = 1;
-        sync();
-        addr = kallsyms_lookup_name("__log_buf");
+	kmsg_dump_rewind_nolock(&dumper);
+	while (kmsg_dump_get_line_nolock(&dumper, false, buf, sizeof(buf), &len)) {
+		buf[len] = '\0';
+		printf("%s", buf);
+	}
 
-        if (! addr)
-                printf("Symbol __log_buf not found!\n");
-        else {
-                end = addr + (1 << CONFIG_LOG_BUF_SHIFT);
-                while (addr < end) {
-                        if (! mread(addr, buf, size)) {
-                                printf("Can't read memory at address 0x%lx\n", addr);
-                                break;
-                        }
-
-                        printf("%s", buf);
-
-                        if (strlen(buf) < size)
-                                break;
-
-                        addr += size;
-                }
-        }
-
-        sync();
-        /* wait a little while to see if we get a machine check */
-        __delay(200);
-        catch_memory_errors = 0;
+	sync();
+	/* wait a little while to see if we get a machine check */
+	__delay(200);
+	catch_memory_errors = 0;
 }
 
 /*
diff --git a/arch/s390/include/asm/elf.h b/arch/s390/include/asm/elf.h
index 32e8449..9b94a16 100644
--- a/arch/s390/include/asm/elf.h
+++ b/arch/s390/include/asm/elf.h
@@ -180,7 +180,8 @@
 #define ELF_PLATFORM (elf_platform)
 
 #ifndef CONFIG_64BIT
-#define SET_PERSONALITY(ex) set_personality(PER_LINUX)
+#define SET_PERSONALITY(ex) \
+	set_personality(PER_LINUX | (current->personality & (~PER_MASK)))
 #else /* CONFIG_64BIT */
 #define SET_PERSONALITY(ex)					\
 do {								\
diff --git a/arch/s390/include/asm/posix_types.h b/arch/s390/include/asm/posix_types.h
index 7bcc14e..bf2a2ad 100644
--- a/arch/s390/include/asm/posix_types.h
+++ b/arch/s390/include/asm/posix_types.h
@@ -13,6 +13,7 @@
  */
 
 typedef unsigned long   __kernel_size_t;
+typedef long            __kernel_ssize_t;
 #define __kernel_size_t __kernel_size_t
 
 typedef unsigned short	__kernel_old_dev_t;
@@ -25,7 +26,6 @@
 typedef unsigned short  __kernel_ipc_pid_t;
 typedef unsigned short  __kernel_uid_t;
 typedef unsigned short  __kernel_gid_t;
-typedef int             __kernel_ssize_t;
 typedef int             __kernel_ptrdiff_t;
 
 #else /* __s390x__ */
@@ -35,7 +35,6 @@
 typedef int             __kernel_ipc_pid_t;
 typedef unsigned int    __kernel_uid_t;
 typedef unsigned int    __kernel_gid_t;
-typedef long            __kernel_ssize_t;
 typedef long            __kernel_ptrdiff_t;
 typedef unsigned long   __kernel_sigset_t;      /* at least 32 bits */
 
diff --git a/arch/s390/include/asm/smp.h b/arch/s390/include/asm/smp.h
index a0a8340..ce26ac3 100644
--- a/arch/s390/include/asm/smp.h
+++ b/arch/s390/include/asm/smp.h
@@ -44,6 +44,7 @@
 }
 
 static inline int smp_find_processor_id(int address) { return 0; }
+static inline int smp_store_status(int cpu) { return 0; }
 static inline int smp_vcpu_scheduled(int cpu) { return 1; }
 static inline void smp_yield_cpu(int cpu) { }
 static inline void smp_yield(void) { }
diff --git a/arch/um/drivers/line.c b/arch/um/drivers/line.c
index bbaf2c5..457475f 100644
--- a/arch/um/drivers/line.c
+++ b/arch/um/drivers/line.c
@@ -409,7 +409,8 @@
 		line->valid = 1;
 		err = parse_chan_pair(new, line, n, opts, error_out);
 		if (!err) {
-			struct device *d = tty_register_device(driver, n, NULL);
+			struct device *d = tty_port_register_device(&line->port,
+					driver, n, NULL);
 			if (IS_ERR(d)) {
 				*error_out = "Failed to register device";
 				err = PTR_ERR(d);
diff --git a/arch/um/os-Linux/time.c b/arch/um/os-Linux/time.c
index f602385..0748fe0 100644
--- a/arch/um/os-Linux/time.c
+++ b/arch/um/os-Linux/time.c
@@ -114,7 +114,7 @@
 	skew += this_tick - last_tick;
 
 	while (skew >= one_tick) {
-		alarm_handler(SIGVTALRM, NULL);
+		alarm_handler(SIGVTALRM, NULL, NULL);
 		skew -= one_tick;
 	}
 
diff --git a/arch/x86/include/asm/spinlock.h b/arch/x86/include/asm/spinlock.h
index b315a33..33692ea 100644
--- a/arch/x86/include/asm/spinlock.h
+++ b/arch/x86/include/asm/spinlock.h
@@ -12,8 +12,7 @@
  * Simple spin lock operations.  There are two variants, one clears IRQ's
  * on the local processor, one does not.
  *
- * These are fair FIFO ticket locks, which are currently limited to 256
- * CPUs.
+ * These are fair FIFO ticket locks, which support up to 2^16 CPUs.
  *
  * (the type definitions are in asm/spinlock_types.h)
  */
diff --git a/arch/x86/kernel/alternative.c b/arch/x86/kernel/alternative.c
index afb7ff7..ced4534 100644
--- a/arch/x86/kernel/alternative.c
+++ b/arch/x86/kernel/alternative.c
@@ -165,7 +165,7 @@
 #endif
 
 #ifdef P6_NOP1
-static const unsigned char  __initconst_or_module p6nops[] =
+static const unsigned char p6nops[] =
 {
 	P6_NOP1,
 	P6_NOP2,
diff --git a/arch/x86/kernel/irq.c b/arch/x86/kernel/irq.c
index 7ad683d..d44f782 100644
--- a/arch/x86/kernel/irq.c
+++ b/arch/x86/kernel/irq.c
@@ -270,7 +270,7 @@
 
 		if (cpumask_any_and(affinity, cpu_online_mask) >= nr_cpu_ids) {
 			break_affinity = 1;
-			affinity = cpu_all_mask;
+			affinity = cpu_online_mask;
 		}
 
 		chip = irq_data_get_irq_chip(data);
diff --git a/arch/x86/kernel/microcode_amd.c b/arch/x86/kernel/microcode_amd.c
index 8a2ce8f..82746f9 100644
--- a/arch/x86/kernel/microcode_amd.c
+++ b/arch/x86/kernel/microcode_amd.c
@@ -143,11 +143,12 @@
 				  unsigned int *current_size)
 {
 	struct microcode_header_amd *mc_hdr;
-	unsigned int actual_size;
+	unsigned int actual_size, patch_size;
 	u16 equiv_cpu_id;
 
 	/* size of the current patch we're staring at */
-	*current_size = *(u32 *)(ucode_ptr + 4) + SECTION_HDR_SIZE;
+	patch_size = *(u32 *)(ucode_ptr + 4);
+	*current_size = patch_size + SECTION_HDR_SIZE;
 
 	equiv_cpu_id = find_equiv_id();
 	if (!equiv_cpu_id)
@@ -174,7 +175,7 @@
 	/*
 	 * now that the header looks sane, verify its size
 	 */
-	actual_size = verify_ucode_size(cpu, *current_size, leftover_size);
+	actual_size = verify_ucode_size(cpu, patch_size, leftover_size);
 	if (!actual_size)
 		return 0;
 
diff --git a/arch/x86/kvm/emulate.c b/arch/x86/kvm/emulate.c
index 97d9a99..a3b57a2 100644
--- a/arch/x86/kvm/emulate.c
+++ b/arch/x86/kvm/emulate.c
@@ -475,13 +475,26 @@
 	return address_mask(ctxt, reg);
 }
 
+static void masked_increment(ulong *reg, ulong mask, int inc)
+{
+	assign_masked(reg, *reg + inc, mask);
+}
+
 static inline void
 register_address_increment(struct x86_emulate_ctxt *ctxt, unsigned long *reg, int inc)
 {
+	ulong mask;
+
 	if (ctxt->ad_bytes == sizeof(unsigned long))
-		*reg += inc;
+		mask = ~0UL;
 	else
-		*reg = (*reg & ~ad_mask(ctxt)) | ((*reg + inc) & ad_mask(ctxt));
+		mask = ad_mask(ctxt);
+	masked_increment(reg, mask, inc);
+}
+
+static void rsp_increment(struct x86_emulate_ctxt *ctxt, int inc)
+{
+	masked_increment(&ctxt->regs[VCPU_REGS_RSP], stack_mask(ctxt), inc);
 }
 
 static inline void jmp_rel(struct x86_emulate_ctxt *ctxt, int rel)
@@ -1522,8 +1535,8 @@
 {
 	struct segmented_address addr;
 
-	register_address_increment(ctxt, &ctxt->regs[VCPU_REGS_RSP], -bytes);
-	addr.ea = register_address(ctxt, ctxt->regs[VCPU_REGS_RSP]);
+	rsp_increment(ctxt, -bytes);
+	addr.ea = ctxt->regs[VCPU_REGS_RSP] & stack_mask(ctxt);
 	addr.seg = VCPU_SREG_SS;
 
 	return segmented_write(ctxt, addr, data, bytes);
@@ -1542,13 +1555,13 @@
 	int rc;
 	struct segmented_address addr;
 
-	addr.ea = register_address(ctxt, ctxt->regs[VCPU_REGS_RSP]);
+	addr.ea = ctxt->regs[VCPU_REGS_RSP] & stack_mask(ctxt);
 	addr.seg = VCPU_SREG_SS;
 	rc = segmented_read(ctxt, addr, dest, len);
 	if (rc != X86EMUL_CONTINUE)
 		return rc;
 
-	register_address_increment(ctxt, &ctxt->regs[VCPU_REGS_RSP], len);
+	rsp_increment(ctxt, len);
 	return rc;
 }
 
@@ -1688,8 +1701,7 @@
 
 	while (reg >= VCPU_REGS_RAX) {
 		if (reg == VCPU_REGS_RSP) {
-			register_address_increment(ctxt, &ctxt->regs[VCPU_REGS_RSP],
-							ctxt->op_bytes);
+			rsp_increment(ctxt, ctxt->op_bytes);
 			--reg;
 		}
 
@@ -2825,7 +2837,7 @@
 	rc = emulate_pop(ctxt, &ctxt->dst.val, ctxt->op_bytes);
 	if (rc != X86EMUL_CONTINUE)
 		return rc;
-	register_address_increment(ctxt, &ctxt->regs[VCPU_REGS_RSP], ctxt->src.val);
+	rsp_increment(ctxt, ctxt->src.val);
 	return X86EMUL_CONTINUE;
 }
 
diff --git a/arch/x86/kvm/mmu.c b/arch/x86/kvm/mmu.c
index 01ca004..7fbd0d2 100644
--- a/arch/x86/kvm/mmu.c
+++ b/arch/x86/kvm/mmu.c
@@ -4113,16 +4113,21 @@
 		LIST_HEAD(invalid_list);
 
 		/*
+		 * Never scan more than sc->nr_to_scan VM instances.
+		 * Will not hit this condition practically since we do not try
+		 * to shrink more than one VM and it is very unlikely to see
+		 * !n_used_mmu_pages so many times.
+		 */
+		if (!nr_to_scan--)
+			break;
+		/*
 		 * n_used_mmu_pages is accessed without holding kvm->mmu_lock
 		 * here. We may skip a VM instance errorneosly, but we do not
 		 * want to shrink a VM that only started to populate its MMU
 		 * anyway.
 		 */
-		if (kvm->arch.n_used_mmu_pages > 0) {
-			if (!nr_to_scan--)
-				break;
+		if (!kvm->arch.n_used_mmu_pages)
 			continue;
-		}
 
 		idx = srcu_read_lock(&kvm->srcu);
 		spin_lock(&kvm->mmu_lock);
diff --git a/arch/x86/kvm/x86.c b/arch/x86/kvm/x86.c
index 42bce48..148ed66 100644
--- a/arch/x86/kvm/x86.c
+++ b/arch/x86/kvm/x86.c
@@ -806,7 +806,7 @@
  * kvm-specific. Those are put in the beginning of the list.
  */
 
-#define KVM_SAVE_MSRS_BEGIN	9
+#define KVM_SAVE_MSRS_BEGIN	10
 static u32 msrs_to_save[] = {
 	MSR_KVM_SYSTEM_TIME, MSR_KVM_WALL_CLOCK,
 	MSR_KVM_SYSTEM_TIME_NEW, MSR_KVM_WALL_CLOCK_NEW,
@@ -2000,6 +2000,9 @@
 	case MSR_KVM_STEAL_TIME:
 		data = vcpu->arch.st.msr_val;
 		break;
+	case MSR_KVM_PV_EOI_EN:
+		data = vcpu->arch.pv_eoi.msr_val;
+		break;
 	case MSR_IA32_P5_MC_ADDR:
 	case MSR_IA32_P5_MC_TYPE:
 	case MSR_IA32_MCG_CAP:
diff --git a/arch/x86/xen/enlighten.c b/arch/x86/xen/enlighten.c
index bf4bda6..9642d4a 100644
--- a/arch/x86/xen/enlighten.c
+++ b/arch/x86/xen/enlighten.c
@@ -31,7 +31,6 @@
 #include <linux/pci.h>
 #include <linux/gfp.h>
 #include <linux/memblock.h>
-#include <linux/syscore_ops.h>
 
 #include <xen/xen.h>
 #include <xen/interface/xen.h>
@@ -1470,130 +1469,38 @@
 #endif
 }
 
-#ifdef CONFIG_XEN_PVHVM
-/*
- * The pfn containing the shared_info is located somewhere in RAM. This
- * will cause trouble if the current kernel is doing a kexec boot into a
- * new kernel. The new kernel (and its startup code) can not know where
- * the pfn is, so it can not reserve the page. The hypervisor will
- * continue to update the pfn, and as a result memory corruption occours
- * in the new kernel.
- *
- * One way to work around this issue is to allocate a page in the
- * xen-platform pci device's BAR memory range. But pci init is done very
- * late and the shared_info page is already in use very early to read
- * the pvclock. So moving the pfn from RAM to MMIO is racy because some
- * code paths on other vcpus could access the pfn during the small
- * window when the old pfn is moved to the new pfn. There is even a
- * small window were the old pfn is not backed by a mfn, and during that
- * time all reads return -1.
- *
- * Because it is not known upfront where the MMIO region is located it
- * can not be used right from the start in xen_hvm_init_shared_info.
- *
- * To minimise trouble the move of the pfn is done shortly before kexec.
- * This does not eliminate the race because all vcpus are still online
- * when the syscore_ops will be called. But hopefully there is no work
- * pending at this point in time. Also the syscore_op is run last which
- * reduces the risk further.
- */
-
-static struct shared_info *xen_hvm_shared_info;
-
-static void xen_hvm_connect_shared_info(unsigned long pfn)
+void __ref xen_hvm_init_shared_info(void)
 {
+	int cpu;
 	struct xen_add_to_physmap xatp;
+	static struct shared_info *shared_info_page = 0;
 
+	if (!shared_info_page)
+		shared_info_page = (struct shared_info *)
+			extend_brk(PAGE_SIZE, PAGE_SIZE);
 	xatp.domid = DOMID_SELF;
 	xatp.idx = 0;
 	xatp.space = XENMAPSPACE_shared_info;
-	xatp.gpfn = pfn;
+	xatp.gpfn = __pa(shared_info_page) >> PAGE_SHIFT;
 	if (HYPERVISOR_memory_op(XENMEM_add_to_physmap, &xatp))
 		BUG();
 
-}
-static void xen_hvm_set_shared_info(struct shared_info *sip)
-{
-	int cpu;
-
-	HYPERVISOR_shared_info = sip;
+	HYPERVISOR_shared_info = (struct shared_info *)shared_info_page;
 
 	/* xen_vcpu is a pointer to the vcpu_info struct in the shared_info
 	 * page, we use it in the event channel upcall and in some pvclock
 	 * related functions. We don't need the vcpu_info placement
 	 * optimizations because we don't use any pv_mmu or pv_irq op on
 	 * HVM.
-	 * When xen_hvm_set_shared_info is run at boot time only vcpu 0 is
-	 * online but xen_hvm_set_shared_info is run at resume time too and
+	 * When xen_hvm_init_shared_info is run at boot time only vcpu 0 is
+	 * online but xen_hvm_init_shared_info is run at resume time too and
 	 * in that case multiple vcpus might be online. */
 	for_each_online_cpu(cpu) {
 		per_cpu(xen_vcpu, cpu) = &HYPERVISOR_shared_info->vcpu_info[cpu];
 	}
 }
 
-/* Reconnect the shared_info pfn to a mfn */
-void xen_hvm_resume_shared_info(void)
-{
-	xen_hvm_connect_shared_info(__pa(xen_hvm_shared_info) >> PAGE_SHIFT);
-}
-
-#ifdef CONFIG_KEXEC
-static struct shared_info *xen_hvm_shared_info_kexec;
-static unsigned long xen_hvm_shared_info_pfn_kexec;
-
-/* Remember a pfn in MMIO space for kexec reboot */
-void __devinit xen_hvm_prepare_kexec(struct shared_info *sip, unsigned long pfn)
-{
-	xen_hvm_shared_info_kexec = sip;
-	xen_hvm_shared_info_pfn_kexec = pfn;
-}
-
-static void xen_hvm_syscore_shutdown(void)
-{
-	struct xen_memory_reservation reservation = {
-		.domid = DOMID_SELF,
-		.nr_extents = 1,
-	};
-	unsigned long prev_pfn;
-	int rc;
-
-	if (!xen_hvm_shared_info_kexec)
-		return;
-
-	prev_pfn = __pa(xen_hvm_shared_info) >> PAGE_SHIFT;
-	set_xen_guest_handle(reservation.extent_start, &prev_pfn);
-
-	/* Move pfn to MMIO, disconnects previous pfn from mfn */
-	xen_hvm_connect_shared_info(xen_hvm_shared_info_pfn_kexec);
-
-	/* Update pointers, following hypercall is also a memory barrier */
-	xen_hvm_set_shared_info(xen_hvm_shared_info_kexec);
-
-	/* Allocate new mfn for previous pfn */
-	do {
-		rc = HYPERVISOR_memory_op(XENMEM_populate_physmap, &reservation);
-		if (rc == 0)
-			msleep(123);
-	} while (rc == 0);
-
-	/* Make sure the previous pfn is really connected to a (new) mfn */
-	BUG_ON(rc != 1);
-}
-
-static struct syscore_ops xen_hvm_syscore_ops = {
-	.shutdown = xen_hvm_syscore_shutdown,
-};
-#endif
-
-/* Use a pfn in RAM, may move to MMIO before kexec. */
-static void __init xen_hvm_init_shared_info(void)
-{
-	/* Remember pointer for resume */
-	xen_hvm_shared_info = extend_brk(PAGE_SIZE, PAGE_SIZE);
-	xen_hvm_connect_shared_info(__pa(xen_hvm_shared_info) >> PAGE_SHIFT);
-	xen_hvm_set_shared_info(xen_hvm_shared_info);
-}
-
+#ifdef CONFIG_XEN_PVHVM
 static void __init init_hvm_pv_info(void)
 {
 	int major, minor;
@@ -1644,9 +1551,6 @@
 	init_hvm_pv_info();
 
 	xen_hvm_init_shared_info();
-#ifdef CONFIG_KEXEC
-	register_syscore_ops(&xen_hvm_syscore_ops);
-#endif
 
 	if (xen_feature(XENFEAT_hvm_callback_vector))
 		xen_have_vector_callback = 1;
diff --git a/arch/x86/xen/mmu.c b/arch/x86/xen/mmu.c
index b65a761..5141d80 100644
--- a/arch/x86/xen/mmu.c
+++ b/arch/x86/xen/mmu.c
@@ -1283,7 +1283,7 @@
 	cpumask_clear_cpu(smp_processor_id(), to_cpumask(args->mask));
 
 	args->op.cmd = MMUEXT_TLB_FLUSH_MULTI;
-	if (start != TLB_FLUSH_ALL && (end - start) <= PAGE_SIZE) {
+	if (end != TLB_FLUSH_ALL && (end - start) <= PAGE_SIZE) {
 		args->op.cmd = MMUEXT_INVLPG_MULTI;
 		args->op.arg1.linear_addr = start;
 	}
diff --git a/arch/x86/xen/p2m.c b/arch/x86/xen/p2m.c
index b2e91d4..76ba0e9 100644
--- a/arch/x86/xen/p2m.c
+++ b/arch/x86/xen/p2m.c
@@ -196,9 +196,11 @@
 
 /* When we populate back during bootup, the amount of pages can vary. The
  * max we have is seen is 395979, but that does not mean it can't be more.
- * But some machines can have 3GB I/O holes even. So lets reserve enough
- * for 4GB of I/O and E820 holes. */
-RESERVE_BRK(p2m_populated, PMD_SIZE * 4);
+ * Some machines can have 3GB I/O holes even. With early_can_reuse_p2m_middle
+ * it can re-use Xen provided mfn_list array, so we only need to allocate at
+ * most three P2M top nodes. */
+RESERVE_BRK(p2m_populated, PAGE_SIZE * 3);
+
 static inline unsigned p2m_top_index(unsigned long pfn)
 {
 	BUG_ON(pfn >= MAX_P2M_PFN);
@@ -575,12 +577,99 @@
 	}
 	return true;
 }
+
+/*
+ * Skim over the P2M tree looking at pages that are either filled with
+ * INVALID_P2M_ENTRY or with 1:1 PFNs. If found, re-use that page and
+ * replace the P2M leaf with a p2m_missing or p2m_identity.
+ * Stick the old page in the new P2M tree location.
+ */
+bool __init early_can_reuse_p2m_middle(unsigned long set_pfn, unsigned long set_mfn)
+{
+	unsigned topidx;
+	unsigned mididx;
+	unsigned ident_pfns;
+	unsigned inv_pfns;
+	unsigned long *p2m;
+	unsigned long *mid_mfn_p;
+	unsigned idx;
+	unsigned long pfn;
+
+	/* We only look when this entails a P2M middle layer */
+	if (p2m_index(set_pfn))
+		return false;
+
+	for (pfn = 0; pfn < MAX_DOMAIN_PAGES; pfn += P2M_PER_PAGE) {
+		topidx = p2m_top_index(pfn);
+
+		if (!p2m_top[topidx])
+			continue;
+
+		if (p2m_top[topidx] == p2m_mid_missing)
+			continue;
+
+		mididx = p2m_mid_index(pfn);
+		p2m = p2m_top[topidx][mididx];
+		if (!p2m)
+			continue;
+
+		if ((p2m == p2m_missing) || (p2m == p2m_identity))
+			continue;
+
+		if ((unsigned long)p2m == INVALID_P2M_ENTRY)
+			continue;
+
+		ident_pfns = 0;
+		inv_pfns = 0;
+		for (idx = 0; idx < P2M_PER_PAGE; idx++) {
+			/* IDENTITY_PFNs are 1:1 */
+			if (p2m[idx] == IDENTITY_FRAME(pfn + idx))
+				ident_pfns++;
+			else if (p2m[idx] == INVALID_P2M_ENTRY)
+				inv_pfns++;
+			else
+				break;
+		}
+		if ((ident_pfns == P2M_PER_PAGE) || (inv_pfns == P2M_PER_PAGE))
+			goto found;
+	}
+	return false;
+found:
+	/* Found one, replace old with p2m_identity or p2m_missing */
+	p2m_top[topidx][mididx] = (ident_pfns ? p2m_identity : p2m_missing);
+	/* And the other for save/restore.. */
+	mid_mfn_p = p2m_top_mfn_p[topidx];
+	/* NOTE: Even if it is a p2m_identity it should still be point to
+	 * a page filled with INVALID_P2M_ENTRY entries. */
+	mid_mfn_p[mididx] = virt_to_mfn(p2m_missing);
+
+	/* Reset where we want to stick the old page in. */
+	topidx = p2m_top_index(set_pfn);
+	mididx = p2m_mid_index(set_pfn);
+
+	/* This shouldn't happen */
+	if (WARN_ON(p2m_top[topidx] == p2m_mid_missing))
+		early_alloc_p2m(set_pfn);
+
+	if (WARN_ON(p2m_top[topidx][mididx] != p2m_missing))
+		return false;
+
+	p2m_init(p2m);
+	p2m_top[topidx][mididx] = p2m;
+	mid_mfn_p = p2m_top_mfn_p[topidx];
+	mid_mfn_p[mididx] = virt_to_mfn(p2m);
+
+	return true;
+}
 bool __init early_set_phys_to_machine(unsigned long pfn, unsigned long mfn)
 {
 	if (unlikely(!__set_phys_to_machine(pfn, mfn)))  {
 		if (!early_alloc_p2m(pfn))
 			return false;
 
+		if (early_can_reuse_p2m_middle(pfn, mfn))
+			return __set_phys_to_machine(pfn, mfn);
+
 		if (!early_alloc_p2m_middle(pfn, false /* boundary crossover OK!*/))
 			return false;
 
diff --git a/arch/x86/xen/setup.c b/arch/x86/xen/setup.c
index ead8557..d11ca11 100644
--- a/arch/x86/xen/setup.c
+++ b/arch/x86/xen/setup.c
@@ -78,9 +78,16 @@
 	memblock_reserve(start, size);
 
 	xen_max_p2m_pfn = PFN_DOWN(start + size);
+	for (pfn = PFN_DOWN(start); pfn < xen_max_p2m_pfn; pfn++) {
+		unsigned long mfn = pfn_to_mfn(pfn);
 
-	for (pfn = PFN_DOWN(start); pfn <= xen_max_p2m_pfn; pfn++)
+		if (WARN(mfn == pfn, "Trying to over-write 1-1 mapping (pfn: %lx)\n", pfn))
+			continue;
+		WARN(mfn != INVALID_P2M_ENTRY, "Trying to remove %lx which has %lx mfn!\n",
+			pfn, mfn);
+
 		__set_phys_to_machine(pfn, INVALID_P2M_ENTRY);
+	}
 }
 
 static unsigned long __init xen_do_chunk(unsigned long start,
diff --git a/arch/x86/xen/suspend.c b/arch/x86/xen/suspend.c
index ae8a00c..45329c8 100644
--- a/arch/x86/xen/suspend.c
+++ b/arch/x86/xen/suspend.c
@@ -30,7 +30,7 @@
 {
 #ifdef CONFIG_XEN_PVHVM
 	int cpu;
-	xen_hvm_resume_shared_info();
+	xen_hvm_init_shared_info();
 	xen_callback_vector();
 	xen_unplug_emulated_devices();
 	if (xen_feature(XENFEAT_hvm_safe_pvclock)) {
diff --git a/arch/x86/xen/xen-ops.h b/arch/x86/xen/xen-ops.h
index 1e4329e..202d4c1 100644
--- a/arch/x86/xen/xen-ops.h
+++ b/arch/x86/xen/xen-ops.h
@@ -41,7 +41,7 @@
 void xen_vcpu_restore(void);
 
 void xen_callback_vector(void);
-void xen_hvm_resume_shared_info(void);
+void xen_hvm_init_shared_info(void);
 void xen_unplug_emulated_devices(void);
 
 void __init xen_build_dynamic_phys_to_machine(void);
diff --git a/arch/xtensa/platforms/iss/console.c b/arch/xtensa/platforms/iss/console.c
index f9726f6..2cd3d3a 100644
--- a/arch/xtensa/platforms/iss/console.c
+++ b/arch/xtensa/platforms/iss/console.c
@@ -223,6 +223,7 @@
 	serial_driver->flags = TTY_DRIVER_REAL_RAW;
 
 	tty_set_operations(serial_driver, &serial_ops);
+	tty_port_link_device(&serial_port, serial_driver, 0);
 
 	if (tty_register_driver(serial_driver))
 		panic("Couldn't register serial driver\n");
diff --git a/block/blk-lib.c b/block/blk-lib.c
index 2b461b4..19cc761 100644
--- a/block/blk-lib.c
+++ b/block/blk-lib.c
@@ -44,6 +44,7 @@
 	struct request_queue *q = bdev_get_queue(bdev);
 	int type = REQ_WRITE | REQ_DISCARD;
 	unsigned int max_discard_sectors;
+	unsigned int granularity, alignment, mask;
 	struct bio_batch bb;
 	struct bio *bio;
 	int ret = 0;
@@ -54,18 +55,20 @@
 	if (!blk_queue_discard(q))
 		return -EOPNOTSUPP;
 
+	/* Zero-sector (unknown) and one-sector granularities are the same.  */
+	granularity = max(q->limits.discard_granularity >> 9, 1U);
+	mask = granularity - 1;
+	alignment = (bdev_discard_alignment(bdev) >> 9) & mask;
+
 	/*
 	 * Ensure that max_discard_sectors is of the proper
-	 * granularity
+	 * granularity, so that requests stay aligned after a split.
 	 */
 	max_discard_sectors = min(q->limits.max_discard_sectors, UINT_MAX >> 9);
+	max_discard_sectors = round_down(max_discard_sectors, granularity);
 	if (unlikely(!max_discard_sectors)) {
 		/* Avoid infinite loop below. Being cautious never hurts. */
 		return -EOPNOTSUPP;
-	} else if (q->limits.discard_granularity) {
-		unsigned int disc_sects = q->limits.discard_granularity >> 9;
-
-		max_discard_sectors &= ~(disc_sects - 1);
 	}
 
 	if (flags & BLKDEV_DISCARD_SECURE) {
@@ -79,25 +82,37 @@
 	bb.wait = &wait;
 
 	while (nr_sects) {
+		unsigned int req_sects;
+		sector_t end_sect;
+
 		bio = bio_alloc(gfp_mask, 1);
 		if (!bio) {
 			ret = -ENOMEM;
 			break;
 		}
 
+		req_sects = min_t(sector_t, nr_sects, max_discard_sectors);
+
+		/*
+		 * If splitting a request, and the next starting sector would be
+		 * misaligned, stop the discard at the previous aligned sector.
+		 */
+		end_sect = sector + req_sects;
+		if (req_sects < nr_sects && (end_sect & mask) != alignment) {
+			end_sect =
+				round_down(end_sect - alignment, granularity)
+				+ alignment;
+			req_sects = end_sect - sector;
+		}
+
 		bio->bi_sector = sector;
 		bio->bi_end_io = bio_batch_end_io;
 		bio->bi_bdev = bdev;
 		bio->bi_private = &bb;
 
-		if (nr_sects > max_discard_sectors) {
-			bio->bi_size = max_discard_sectors << 9;
-			nr_sects -= max_discard_sectors;
-			sector += max_discard_sectors;
-		} else {
-			bio->bi_size = nr_sects << 9;
-			nr_sects = 0;
-		}
+		bio->bi_size = req_sects << 9;
+		nr_sects -= req_sects;
+		sector = end_sect;
 
 		atomic_inc(&bb.done);
 		submit_bio(type, bio);
diff --git a/block/blk-merge.c b/block/blk-merge.c
index 160035f..e76279e 100644
--- a/block/blk-merge.c
+++ b/block/blk-merge.c
@@ -110,6 +110,49 @@
 	return 0;
 }
 
+static void
+__blk_segment_map_sg(struct request_queue *q, struct bio_vec *bvec,
+		     struct scatterlist *sglist, struct bio_vec **bvprv,
+		     struct scatterlist **sg, int *nsegs, int *cluster)
+{
+
+	int nbytes = bvec->bv_len;
+
+	if (*bvprv && *cluster) {
+		if ((*sg)->length + nbytes > queue_max_segment_size(q))
+			goto new_segment;
+
+		if (!BIOVEC_PHYS_MERGEABLE(*bvprv, bvec))
+			goto new_segment;
+		if (!BIOVEC_SEG_BOUNDARY(q, *bvprv, bvec))
+			goto new_segment;
+
+		(*sg)->length += nbytes;
+	} else {
+new_segment:
+		if (!*sg)
+			*sg = sglist;
+		else {
+			/*
+			 * If the driver previously mapped a shorter
+			 * list, we could see a termination bit
+			 * prematurely unless it fully inits the sg
+			 * table on each mapping. We KNOW that there
+			 * must be more entries here or the driver
+			 * would be buggy, so force clear the
+			 * termination bit to avoid doing a full
+			 * sg_init_table() in drivers for each command.
+			 */
+			(*sg)->page_link &= ~0x02;
+			*sg = sg_next(*sg);
+		}
+
+		sg_set_page(*sg, bvec->bv_page, nbytes, bvec->bv_offset);
+		(*nsegs)++;
+	}
+	*bvprv = bvec;
+}
+
 /*
  * map a request to scatterlist, return number of sg entries setup. Caller
  * must make sure sg can hold rq->nr_phys_segments entries
@@ -131,41 +174,8 @@
 	bvprv = NULL;
 	sg = NULL;
 	rq_for_each_segment(bvec, rq, iter) {
-		int nbytes = bvec->bv_len;
-
-		if (bvprv && cluster) {
-			if (sg->length + nbytes > queue_max_segment_size(q))
-				goto new_segment;
-
-			if (!BIOVEC_PHYS_MERGEABLE(bvprv, bvec))
-				goto new_segment;
-			if (!BIOVEC_SEG_BOUNDARY(q, bvprv, bvec))
-				goto new_segment;
-
-			sg->length += nbytes;
-		} else {
-new_segment:
-			if (!sg)
-				sg = sglist;
-			else {
-				/*
-				 * If the driver previously mapped a shorter
-				 * list, we could see a termination bit
-				 * prematurely unless it fully inits the sg
-				 * table on each mapping. We KNOW that there
-				 * must be more entries here or the driver
-				 * would be buggy, so force clear the
-				 * termination bit to avoid doing a full
-				 * sg_init_table() in drivers for each command.
-				 */
-				sg->page_link &= ~0x02;
-				sg = sg_next(sg);
-			}
-
-			sg_set_page(sg, bvec->bv_page, nbytes, bvec->bv_offset);
-			nsegs++;
-		}
-		bvprv = bvec;
+		__blk_segment_map_sg(q, bvec, sglist, &bvprv, &sg,
+				     &nsegs, &cluster);
 	} /* segments in rq */
 
 
@@ -199,6 +209,43 @@
 }
 EXPORT_SYMBOL(blk_rq_map_sg);
 
+/**
+ * blk_bio_map_sg - map a bio to a scatterlist
+ * @q: request_queue in question
+ * @bio: bio being mapped
+ * @sglist: scatterlist being mapped
+ *
+ * Note:
+ *    Caller must make sure sg can hold bio->bi_phys_segments entries
+ *
+ * Will return the number of sg entries setup
+ */
+int blk_bio_map_sg(struct request_queue *q, struct bio *bio,
+		   struct scatterlist *sglist)
+{
+	struct bio_vec *bvec, *bvprv;
+	struct scatterlist *sg;
+	int nsegs, cluster;
+	unsigned long i;
+
+	nsegs = 0;
+	cluster = blk_queue_cluster(q);
+
+	bvprv = NULL;
+	sg = NULL;
+	bio_for_each_segment(bvec, bio, i) {
+		__blk_segment_map_sg(q, bvec, sglist, &bvprv, &sg,
+				     &nsegs, &cluster);
+	} /* segments in bio */
+
+	if (sg)
+		sg_mark_end(sg);
+
+	BUG_ON(bio->bi_phys_segments && nsegs > bio->bi_phys_segments);
+	return nsegs;
+}
+EXPORT_SYMBOL(blk_bio_map_sg);
+
 static inline int ll_new_hw_segment(struct request_queue *q,
 				    struct request *req,
 				    struct bio *bio)
diff --git a/block/genhd.c b/block/genhd.c
index cac7366..d839723 100644
--- a/block/genhd.c
+++ b/block/genhd.c
@@ -835,7 +835,7 @@
 
 static void *show_partition_start(struct seq_file *seqf, loff_t *pos)
 {
-	static void *p;
+	void *p;
 
 	p = disk_seqf_start(seqf, pos);
 	if (!IS_ERR_OR_NULL(p) && !*pos)
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index 2be8ef1..27cecd3 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -115,7 +115,7 @@
 	  If unsure, say N.
 
 config ATA_SFF
-	bool "ATA SFF support"
+	bool "ATA SFF support (for legacy IDE and PATA)"
 	default y
 	help
 	  This option adds support for ATA controllers with SFF
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index 062e6a1..50d5dea 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -256,6 +256,14 @@
 	{ PCI_VDEVICE(INTEL, 0x8c07), board_ahci }, /* Lynx Point RAID */
 	{ PCI_VDEVICE(INTEL, 0x8c0e), board_ahci }, /* Lynx Point RAID */
 	{ PCI_VDEVICE(INTEL, 0x8c0f), board_ahci }, /* Lynx Point RAID */
+	{ PCI_VDEVICE(INTEL, 0x9c02), board_ahci }, /* Lynx Point-LP AHCI */
+	{ PCI_VDEVICE(INTEL, 0x9c03), board_ahci }, /* Lynx Point-LP AHCI */
+	{ PCI_VDEVICE(INTEL, 0x9c04), board_ahci }, /* Lynx Point-LP RAID */
+	{ PCI_VDEVICE(INTEL, 0x9c05), board_ahci }, /* Lynx Point-LP RAID */
+	{ PCI_VDEVICE(INTEL, 0x9c06), board_ahci }, /* Lynx Point-LP RAID */
+	{ PCI_VDEVICE(INTEL, 0x9c07), board_ahci }, /* Lynx Point-LP RAID */
+	{ PCI_VDEVICE(INTEL, 0x9c0e), board_ahci }, /* Lynx Point-LP RAID */
+	{ PCI_VDEVICE(INTEL, 0x9c0f), board_ahci }, /* Lynx Point-LP RAID */
 
 	/* JMicron 360/1/3/5/6, match class to avoid IDE function */
 	{ PCI_VENDOR_ID_JMICRON, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
diff --git a/drivers/ata/ahci.h b/drivers/ata/ahci.h
index c2594dd..57eb1c2 100644
--- a/drivers/ata/ahci.h
+++ b/drivers/ata/ahci.h
@@ -320,6 +320,7 @@
 extern struct ata_port_operations ahci_ops;
 extern struct ata_port_operations ahci_pmp_retry_srst_ops;
 
+unsigned int ahci_dev_classify(struct ata_port *ap);
 void ahci_fill_cmd_slot(struct ahci_port_priv *pp, unsigned int tag,
 			u32 opts);
 void ahci_save_initial_config(struct device *dev,
diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
index 3c809bf..ef773e1 100644
--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -329,6 +329,14 @@
 	{ 0x8086, 0x8c08, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
 	/* SATA Controller IDE (Lynx Point) */
 	{ 0x8086, 0x8c09, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
+	/* SATA Controller IDE (Lynx Point-LP) */
+	{ 0x8086, 0x9c00, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_snb },
+	/* SATA Controller IDE (Lynx Point-LP) */
+	{ 0x8086, 0x9c01, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_snb },
+	/* SATA Controller IDE (Lynx Point-LP) */
+	{ 0x8086, 0x9c08, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
+	/* SATA Controller IDE (Lynx Point-LP) */
+	{ 0x8086, 0x9c09, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
 	/* SATA Controller IDE (DH89xxCC) */
 	{ 0x8086, 0x2326, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
 	{ }	/* terminate list */
diff --git a/drivers/ata/libahci.c b/drivers/ata/libahci.c
index f9eaa82..555c07a 100644
--- a/drivers/ata/libahci.c
+++ b/drivers/ata/libahci.c
@@ -1139,7 +1139,7 @@
 	}
 }
 
-static unsigned int ahci_dev_classify(struct ata_port *ap)
+unsigned int ahci_dev_classify(struct ata_port *ap)
 {
 	void __iomem *port_mmio = ahci_port_base(ap);
 	struct ata_taskfile tf;
@@ -1153,6 +1153,7 @@
 
 	return ata_dev_classify(&tf);
 }
+EXPORT_SYMBOL_GPL(ahci_dev_classify);
 
 void ahci_fill_cmd_slot(struct ahci_port_priv *pp, unsigned int tag,
 			u32 opts)
diff --git a/drivers/ata/libata-acpi.c b/drivers/ata/libata-acpi.c
index 902b5a4..fd9ecf7 100644
--- a/drivers/ata/libata-acpi.c
+++ b/drivers/ata/libata-acpi.c
@@ -60,17 +60,7 @@
 	if (ap->flags & ATA_FLAG_ACPI_SATA)
 		return NULL;
 
-	/*
-	 * If acpi bind operation has already happened, we can get the handle
-	 * for the port by checking the corresponding scsi_host device's
-	 * firmware node, otherwise we will need to find out the handle from
-	 * its parent's acpi node.
-	 */
-	if (ap->scsi_host)
-		return DEVICE_ACPI_HANDLE(&ap->scsi_host->shost_gendev);
-	else
-		return acpi_get_child(DEVICE_ACPI_HANDLE(ap->host->dev),
-				ap->port_no);
+	return acpi_get_child(DEVICE_ACPI_HANDLE(ap->host->dev), ap->port_no);
 }
 EXPORT_SYMBOL(ata_ap_acpi_handle);
 
@@ -1101,6 +1091,9 @@
 	if (!*handle)
 		return -ENODEV;
 
+	if (ata_acpi_gtm(ap, &ap->__acpi_init_gtm) == 0)
+		ap->pflags |= ATA_PFLAG_INIT_GTM_VALID;
+
 	return 0;
 }
 
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index fadd586..8e1039c 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -4062,7 +4062,7 @@
 	{ "_NEC DV5800A", 	NULL,		ATA_HORKAGE_NODMA },
 	{ "SAMSUNG CD-ROM SN-124", "N001",	ATA_HORKAGE_NODMA },
 	{ "Seagate STT20000A", NULL,		ATA_HORKAGE_NODMA },
-	{ "2GB ATA Flash Disk", "ADMA428M",	ATA_HORKAGE_NODMA },
+	{ " 2GB ATA Flash Disk", "ADMA428M",	ATA_HORKAGE_NODMA },
 	/* Odd clown on sil3726/4726 PMPs */
 	{ "Config  Disk",	NULL,		ATA_HORKAGE_DISABLE },
 
@@ -4128,6 +4128,7 @@
 
 	/* Devices that do not need bridging limits applied */
 	{ "MTRON MSP-SATA*",		NULL,	ATA_HORKAGE_BRIDGE_OK, },
+	{ "BUFFALO HD-QSU2/R5",		NULL,	ATA_HORKAGE_BRIDGE_OK, },
 
 	/* Devices which aren't very happy with higher link speeds */
 	{ "WD My Book",			NULL,	ATA_HORKAGE_1_5_GBPS, },
diff --git a/drivers/ata/pata_atiixp.c b/drivers/ata/pata_atiixp.c
index 361c75c..24e5105 100644
--- a/drivers/ata/pata_atiixp.c
+++ b/drivers/ata/pata_atiixp.c
@@ -20,6 +20,7 @@
 #include <linux/delay.h>
 #include <scsi/scsi_host.h>
 #include <linux/libata.h>
+#include <linux/dmi.h>
 
 #define DRV_NAME "pata_atiixp"
 #define DRV_VERSION "0.4.6"
@@ -33,11 +34,26 @@
 	ATIIXP_IDE_UDMA_MODE 	= 0x56
 };
 
+static const struct dmi_system_id attixp_cable_override_dmi_table[] = {
+	{
+		/* Board has onboard PATA<->SATA converters */
+		.ident = "MSI E350DM-E33",
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "MSI"),
+			DMI_MATCH(DMI_BOARD_NAME, "E350DM-E33(MS-7720)"),
+		},
+	},
+	{ }
+};
+
 static int atiixp_cable_detect(struct ata_port *ap)
 {
 	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
 	u8 udma;
 
+	if (dmi_check_system(attixp_cable_override_dmi_table))
+		return ATA_CBL_PATA40_SHORT;
+
 	/* Hack from drivers/ide/pci. Really we want to know how to do the
 	   raw detection not play follow the bios mode guess */
 	pci_read_config_byte(pdev, ATIIXP_IDE_UDMA_MODE + ap->port_no, &udma);
diff --git a/drivers/base/dma-contiguous.c b/drivers/base/dma-contiguous.c
index 78efb03..34d94c7 100644
--- a/drivers/base/dma-contiguous.c
+++ b/drivers/base/dma-contiguous.c
@@ -250,7 +250,7 @@
 		return -EINVAL;
 
 	/* Sanitise input arguments */
-	alignment = PAGE_SIZE << max(MAX_ORDER, pageblock_order);
+	alignment = PAGE_SIZE << max(MAX_ORDER - 1, pageblock_order);
 	base = ALIGN(base, alignment);
 	size = ALIGN(size, alignment);
 	limit &= ~(alignment - 1);
diff --git a/drivers/block/drbd/drbd_bitmap.c b/drivers/block/drbd/drbd_bitmap.c
index ba91b40..d845664 100644
--- a/drivers/block/drbd/drbd_bitmap.c
+++ b/drivers/block/drbd/drbd_bitmap.c
@@ -889,6 +889,7 @@
 	unsigned int done;
 	unsigned flags;
 #define BM_AIO_COPY_PAGES	1
+#define BM_WRITE_ALL_PAGES	2
 	int error;
 	struct kref kref;
 };
@@ -1059,7 +1060,8 @@
 		if (lazy_writeout_upper_idx && i == lazy_writeout_upper_idx)
 			break;
 		if (rw & WRITE) {
-			if (bm_test_page_unchanged(b->bm_pages[i])) {
+			if (!(flags & BM_WRITE_ALL_PAGES) &&
+			    bm_test_page_unchanged(b->bm_pages[i])) {
 				dynamic_dev_dbg(DEV, "skipped bm write for idx %u\n", i);
 				continue;
 			}
@@ -1141,6 +1143,17 @@
 }
 
 /**
+ * drbd_bm_write_all() - Write the whole bitmap to its on disk location.
+ * @mdev:	DRBD device.
+ *
+ * Will write all pages.
+ */
+int drbd_bm_write_all(struct drbd_conf *mdev) __must_hold(local)
+{
+	return bm_rw(mdev, WRITE, BM_WRITE_ALL_PAGES, 0);
+}
+
+/**
  * drbd_bm_lazy_write_out() - Write bitmap pages 0 to @upper_idx-1, if they have changed.
  * @mdev:	DRBD device.
  * @upper_idx:	0: write all changed pages; +ve: page index to stop scanning for changed pages
diff --git a/drivers/block/drbd/drbd_int.h b/drivers/block/drbd/drbd_int.h
index b2ca143..b953cc7 100644
--- a/drivers/block/drbd/drbd_int.h
+++ b/drivers/block/drbd/drbd_int.h
@@ -1469,6 +1469,7 @@
 extern int  drbd_bm_write_page(struct drbd_conf *mdev, unsigned int idx) __must_hold(local);
 extern int  drbd_bm_read(struct drbd_conf *mdev) __must_hold(local);
 extern int  drbd_bm_write(struct drbd_conf *mdev) __must_hold(local);
+extern int drbd_bm_write_all(struct drbd_conf *mdev) __must_hold(local);
 extern int  drbd_bm_write_copy_pages(struct drbd_conf *mdev) __must_hold(local);
 extern unsigned long drbd_bm_ALe_set_all(struct drbd_conf *mdev,
 		unsigned long al_enr);
diff --git a/drivers/block/drbd/drbd_main.c b/drivers/block/drbd/drbd_main.c
index dbe6135..f93a032 100644
--- a/drivers/block/drbd/drbd_main.c
+++ b/drivers/block/drbd/drbd_main.c
@@ -79,6 +79,7 @@
 static void md_sync_timer_fn(unsigned long data);
 static int w_bitmap_io(struct drbd_conf *mdev, struct drbd_work *w, int unused);
 static int w_go_diskless(struct drbd_conf *mdev, struct drbd_work *w, int unused);
+static void _tl_clear(struct drbd_conf *mdev);
 
 MODULE_AUTHOR("Philipp Reisner <phil@linbit.com>, "
 	      "Lars Ellenberg <lars@linbit.com>");
@@ -432,19 +433,10 @@
 
 	/* Actions operating on the disk state, also want to work on
 	   requests that got barrier acked. */
-	switch (what) {
-	case fail_frozen_disk_io:
-	case restart_frozen_disk_io:
-		list_for_each_safe(le, tle, &mdev->barrier_acked_requests) {
-			req = list_entry(le, struct drbd_request, tl_requests);
-			_req_mod(req, what);
-		}
 
-	case connection_lost_while_pending:
-	case resend:
-		break;
-	default:
-		dev_err(DEV, "what = %d in _tl_restart()\n", what);
+	list_for_each_safe(le, tle, &mdev->barrier_acked_requests) {
+		req = list_entry(le, struct drbd_request, tl_requests);
+		_req_mod(req, what);
 	}
 }
 
@@ -459,11 +451,16 @@
  */
 void tl_clear(struct drbd_conf *mdev)
 {
+	spin_lock_irq(&mdev->req_lock);
+	_tl_clear(mdev);
+	spin_unlock_irq(&mdev->req_lock);
+}
+
+static void _tl_clear(struct drbd_conf *mdev)
+{
 	struct list_head *le, *tle;
 	struct drbd_request *r;
 
-	spin_lock_irq(&mdev->req_lock);
-
 	_tl_restart(mdev, connection_lost_while_pending);
 
 	/* we expect this list to be empty. */
@@ -482,7 +479,6 @@
 
 	memset(mdev->app_reads_hash, 0, APP_R_HSIZE*sizeof(void *));
 
-	spin_unlock_irq(&mdev->req_lock);
 }
 
 void tl_restart(struct drbd_conf *mdev, enum drbd_req_event what)
@@ -1476,12 +1472,12 @@
 	if (ns.susp_fen) {
 		/* case1: The outdate peer handler is successful: */
 		if (os.pdsk > D_OUTDATED  && ns.pdsk <= D_OUTDATED) {
-			tl_clear(mdev);
 			if (test_bit(NEW_CUR_UUID, &mdev->flags)) {
 				drbd_uuid_new_current(mdev);
 				clear_bit(NEW_CUR_UUID, &mdev->flags);
 			}
 			spin_lock_irq(&mdev->req_lock);
+			_tl_clear(mdev);
 			_drbd_set_state(_NS(mdev, susp_fen, 0), CS_VERBOSE, NULL);
 			spin_unlock_irq(&mdev->req_lock);
 		}
diff --git a/drivers/block/drbd/drbd_nl.c b/drivers/block/drbd/drbd_nl.c
index fb9dce8..edb490a 100644
--- a/drivers/block/drbd/drbd_nl.c
+++ b/drivers/block/drbd/drbd_nl.c
@@ -674,8 +674,8 @@
 			 la_size_changed && md_moved ? "size changed and md moved" :
 			 la_size_changed ? "size changed" : "md moved");
 		/* next line implicitly does drbd_suspend_io()+drbd_resume_io() */
-		err = drbd_bitmap_io(mdev, &drbd_bm_write,
-				"size changed", BM_LOCKED_MASK);
+		err = drbd_bitmap_io(mdev, md_moved ? &drbd_bm_write_all : &drbd_bm_write,
+				     "size changed", BM_LOCKED_MASK);
 		if (err) {
 			rv = dev_size_error;
 			goto out;
diff --git a/drivers/block/drbd/drbd_req.c b/drivers/block/drbd/drbd_req.c
index 910335c..01b2ac6 100644
--- a/drivers/block/drbd/drbd_req.c
+++ b/drivers/block/drbd/drbd_req.c
@@ -695,6 +695,12 @@
 		break;
 
 	case resend:
+		/* Simply complete (local only) READs. */
+		if (!(req->rq_state & RQ_WRITE) && !req->w.cb) {
+			_req_may_be_done(req, m);
+			break;
+		}
+
 		/* If RQ_NET_OK is already set, we got a P_WRITE_ACK or P_RECV_ACK
 		   before the connection loss (B&C only); only P_BARRIER_ACK was missing.
 		   Trowing them out of the TL here by pretending we got a BARRIER_ACK
@@ -834,7 +840,15 @@
 		req->private_bio = NULL;
 	}
 	if (rw == WRITE) {
-		remote = 1;
+		/* Need to replicate writes.  Unless it is an empty flush,
+		 * which is better mapped to a DRBD P_BARRIER packet,
+		 * also for drbd wire protocol compatibility reasons. */
+		if (unlikely(size == 0)) {
+			/* The only size==0 bios we expect are empty flushes. */
+			D_ASSERT(bio->bi_rw & REQ_FLUSH);
+			remote = 0;
+		} else
+			remote = 1;
 	} else {
 		/* READ || READA */
 		if (local) {
@@ -870,8 +884,11 @@
 	 * extent.  This waits for any resync activity in the corresponding
 	 * resync extent to finish, and, if necessary, pulls in the target
 	 * extent into the activity log, which involves further disk io because
-	 * of transactional on-disk meta data updates. */
-	if (rw == WRITE && local && !test_bit(AL_SUSPENDED, &mdev->flags)) {
+	 * of transactional on-disk meta data updates.
+	 * Empty flushes don't need to go into the activity log, they can only
+	 * flush data for pending writes which are already in there. */
+	if (rw == WRITE && local && size
+	&& !test_bit(AL_SUSPENDED, &mdev->flags)) {
 		req->rq_state |= RQ_IN_ACT_LOG;
 		drbd_al_begin_io(mdev, sector);
 	}
@@ -994,7 +1011,10 @@
 	if (rw == WRITE && _req_conflicts(req))
 		goto fail_conflicting;
 
-	list_add_tail(&req->tl_requests, &mdev->newest_tle->requests);
+	/* no point in adding empty flushes to the transfer log,
+	 * they are mapped to drbd barriers already. */
+	if (likely(size!=0))
+		list_add_tail(&req->tl_requests, &mdev->newest_tle->requests);
 
 	/* NOTE remote first: to get the concurrent write detection right,
 	 * we must register the request before start of local IO.  */
@@ -1014,6 +1034,14 @@
 	    mdev->net_conf->on_congestion != OC_BLOCK && mdev->agreed_pro_version >= 96)
 		maybe_pull_ahead(mdev);
 
+	/* If this was a flush, queue a drbd barrier/start a new epoch.
+	 * Unless the current epoch was empty anyways, or we are not currently
+	 * replicating, in which case there is no point. */
+	if (unlikely(bio->bi_rw & REQ_FLUSH)
+		&& mdev->newest_tle->n_writes
+		&& drbd_should_do_remote(mdev->state))
+		queue_barrier(mdev);
+
 	spin_unlock_irq(&mdev->req_lock);
 	kfree(b); /* if someone else has beaten us to it... */
 
diff --git a/drivers/bluetooth/hci_ath.c b/drivers/bluetooth/hci_ath.c
index 12172a6..0bc8a6a 100644
--- a/drivers/bluetooth/hci_ath.c
+++ b/drivers/bluetooth/hci_ath.c
@@ -58,7 +58,7 @@
 		return status;
 
 	/* Disable Automatic RTSCTS */
-	memcpy(&ktermios, tty->termios, sizeof(ktermios));
+	ktermios = tty->termios;
 	ktermios.c_cflag &= ~CRTSCTS;
 	tty_set_termios(tty, &ktermios);
 
diff --git a/drivers/char/mwave/mwavedd.c b/drivers/char/mwave/mwavedd.c
index 1d82d58..164544a 100644
--- a/drivers/char/mwave/mwavedd.c
+++ b/drivers/char/mwave/mwavedd.c
@@ -430,7 +430,7 @@
 
 static int register_serial_portandirq(unsigned int port, int irq)
 {
-	struct uart_port uart;
+	struct uart_8250_port uart;
 	
 	switch ( port ) {
 		case 0x3f8:
@@ -462,14 +462,14 @@
 	} /* switch */
 	/* irq is okay */
 
-	memset(&uart, 0, sizeof(struct uart_port));
+	memset(&uart, 0, sizeof(uart));
 	
-	uart.uartclk =  1843200;
-	uart.iobase = port;
-	uart.irq = irq;
-	uart.iotype = UPIO_PORT;
-	uart.flags =  UPF_SHARE_IRQ;
-	return serial8250_register_port(&uart);
+	uart.port.uartclk =  1843200;
+	uart.port.iobase = port;
+	uart.port.irq = irq;
+	uart.port.iotype = UPIO_PORT;
+	uart.port.flags =  UPF_SHARE_IRQ;
+	return serial8250_register_8250_port(&uart);
 }
 
 
diff --git a/drivers/char/pcmcia/synclink_cs.c b/drivers/char/pcmcia/synclink_cs.c
index 0a484b4..3f57d5de 100644
--- a/drivers/char/pcmcia/synclink_cs.c
+++ b/drivers/char/pcmcia/synclink_cs.c
@@ -1050,7 +1050,7 @@
 	wake_up_interruptible(&info->status_event_wait_q);
 	wake_up_interruptible(&info->event_wait_q);
 
-	if (info->port.flags & ASYNC_CTS_FLOW) {
+	if (tty_port_cts_enabled(&info->port)) {
 		if (tty->hw_stopped) {
 			if (info->serial_signals & SerialSignal_CTS) {
 				if (debug_level >= DEBUG_LEVEL_ISR)
@@ -1344,7 +1344,7 @@
 	/* TODO:disable interrupts instead of reset to preserve signal states */
 	reset_device(info);
 
- 	if (!tty || tty->termios->c_cflag & HUPCL) {
+ 	if (!tty || tty->termios.c_cflag & HUPCL) {
  		info->serial_signals &= ~(SerialSignal_DTR + SerialSignal_RTS);
 		set_signals(info);
 	}
@@ -1385,7 +1385,7 @@
 	port_irq_enable(info, (unsigned char) PVR_DSR | PVR_RI);
 	get_signals(info);
 
-	if (info->netcount || (tty && (tty->termios->c_cflag & CREAD)))
+	if (info->netcount || (tty && (tty->termios.c_cflag & CREAD)))
 		rx_start(info);
 
 	spin_unlock_irqrestore(&info->lock,flags);
@@ -1398,14 +1398,14 @@
 	unsigned cflag;
 	int bits_per_char;
 
-	if (!tty || !tty->termios)
+	if (!tty)
 		return;
 
 	if (debug_level >= DEBUG_LEVEL_INFO)
 		printk("%s(%d):mgslpc_change_params(%s)\n",
 			 __FILE__,__LINE__, info->device_name );
 
-	cflag = tty->termios->c_cflag;
+	cflag = tty->termios.c_cflag;
 
 	/* if B0 rate (hangup) specified then negate DTR and RTS */
 	/* otherwise assert DTR and RTS */
@@ -1728,7 +1728,7 @@
 	if (I_IXOFF(tty))
 		mgslpc_send_xchar(tty, STOP_CHAR(tty));
 
- 	if (tty->termios->c_cflag & CRTSCTS) {
+ 	if (tty->termios.c_cflag & CRTSCTS) {
 		spin_lock_irqsave(&info->lock,flags);
 		info->serial_signals &= ~SerialSignal_RTS;
 	 	set_signals(info);
@@ -1757,7 +1757,7 @@
 			mgslpc_send_xchar(tty, START_CHAR(tty));
 	}
 
- 	if (tty->termios->c_cflag & CRTSCTS) {
+ 	if (tty->termios.c_cflag & CRTSCTS) {
 		spin_lock_irqsave(&info->lock,flags);
 		info->serial_signals |= SerialSignal_RTS;
 	 	set_signals(info);
@@ -2293,8 +2293,8 @@
 			tty->driver->name );
 
 	/* just return if nothing has changed */
-	if ((tty->termios->c_cflag == old_termios->c_cflag)
-	    && (RELEVANT_IFLAG(tty->termios->c_iflag)
+	if ((tty->termios.c_cflag == old_termios->c_cflag)
+	    && (RELEVANT_IFLAG(tty->termios.c_iflag)
 		== RELEVANT_IFLAG(old_termios->c_iflag)))
 	  return;
 
@@ -2302,7 +2302,7 @@
 
 	/* Handle transition to B0 status */
 	if (old_termios->c_cflag & CBAUD &&
-	    !(tty->termios->c_cflag & CBAUD)) {
+	    !(tty->termios.c_cflag & CBAUD)) {
 		info->serial_signals &= ~(SerialSignal_RTS + SerialSignal_DTR);
 		spin_lock_irqsave(&info->lock,flags);
 	 	set_signals(info);
@@ -2311,9 +2311,9 @@
 
 	/* Handle transition away from B0 status */
 	if (!(old_termios->c_cflag & CBAUD) &&
-	    tty->termios->c_cflag & CBAUD) {
+	    tty->termios.c_cflag & CBAUD) {
 		info->serial_signals |= SerialSignal_DTR;
- 		if (!(tty->termios->c_cflag & CRTSCTS) ||
+ 		if (!(tty->termios.c_cflag & CRTSCTS) ||
  		    !test_bit(TTY_THROTTLED, &tty->flags)) {
 			info->serial_signals |= SerialSignal_RTS;
  		}
@@ -2324,7 +2324,7 @@
 
 	/* Handle turning off CRTSCTS */
 	if (old_termios->c_cflag & CRTSCTS &&
-	    !(tty->termios->c_cflag & CRTSCTS)) {
+	    !(tty->termios.c_cflag & CRTSCTS)) {
 		tty->hw_stopped = 0;
 		tx_release(tty);
 	}
@@ -2731,6 +2731,8 @@
 #if SYNCLINK_GENERIC_HDLC
 	hdlcdev_init(info);
 #endif
+	tty_port_register_device(&info->port, serial_driver, info->line,
+			&info->p_dev->dev);
 }
 
 static void mgslpc_remove_device(MGSLPC_INFO *remove_info)
@@ -2744,6 +2746,7 @@
 				last->next_device = info->next_device;
 			else
 				mgslpc_device_list = info->next_device;
+			tty_unregister_device(serial_driver, info->line);
 #if SYNCLINK_GENERIC_HDLC
 			hdlcdev_exit(info);
 #endif
@@ -2798,77 +2801,63 @@
 	.proc_fops = &mgslpc_proc_fops,
 };
 
-static void synclink_cs_cleanup(void)
+static int __init synclink_cs_init(void)
 {
 	int rc;
 
-	while(mgslpc_device_list)
-		mgslpc_remove_device(mgslpc_device_list);
-
-	if (serial_driver) {
-		if ((rc = tty_unregister_driver(serial_driver)))
-			printk("%s(%d) failed to unregister tty driver err=%d\n",
-			       __FILE__,__LINE__,rc);
-		put_tty_driver(serial_driver);
+	if (break_on_load) {
+		mgslpc_get_text_ptr();
+		BREAKPOINT();
 	}
 
-	pcmcia_unregister_driver(&mgslpc_driver);
-}
+	serial_driver = tty_alloc_driver(MAX_DEVICE_COUNT,
+			TTY_DRIVER_REAL_RAW |
+			TTY_DRIVER_DYNAMIC_DEV);
+	if (IS_ERR(serial_driver)) {
+		rc = PTR_ERR(serial_driver);
+		goto err;
+	}
 
-static int __init synclink_cs_init(void)
-{
-    int rc;
+	/* Initialize the tty_driver structure */
+	serial_driver->driver_name = "synclink_cs";
+	serial_driver->name = "ttySLP";
+	serial_driver->major = ttymajor;
+	serial_driver->minor_start = 64;
+	serial_driver->type = TTY_DRIVER_TYPE_SERIAL;
+	serial_driver->subtype = SERIAL_TYPE_NORMAL;
+	serial_driver->init_termios = tty_std_termios;
+	serial_driver->init_termios.c_cflag =
+	B9600 | CS8 | CREAD | HUPCL | CLOCAL;
+	tty_set_operations(serial_driver, &mgslpc_ops);
 
-    if (break_on_load) {
-	    mgslpc_get_text_ptr();
-	    BREAKPOINT();
-    }
+	rc = tty_register_driver(serial_driver);
+	if (rc < 0) {
+		printk(KERN_ERR "%s(%d):Couldn't register serial driver\n",
+				__FILE__, __LINE__);
+		goto err_put_tty;
+	}
 
-    if ((rc = pcmcia_register_driver(&mgslpc_driver)) < 0)
-	    return rc;
+	rc = pcmcia_register_driver(&mgslpc_driver);
+	if (rc < 0)
+		goto err_unreg_tty;
 
-    serial_driver = alloc_tty_driver(MAX_DEVICE_COUNT);
-    if (!serial_driver) {
-	    rc = -ENOMEM;
-	    goto error;
-    }
+	printk(KERN_INFO "%s %s, tty major#%d\n", driver_name, driver_version,
+			serial_driver->major);
 
-    /* Initialize the tty_driver structure */
-
-    serial_driver->driver_name = "synclink_cs";
-    serial_driver->name = "ttySLP";
-    serial_driver->major = ttymajor;
-    serial_driver->minor_start = 64;
-    serial_driver->type = TTY_DRIVER_TYPE_SERIAL;
-    serial_driver->subtype = SERIAL_TYPE_NORMAL;
-    serial_driver->init_termios = tty_std_termios;
-    serial_driver->init_termios.c_cflag =
-	    B9600 | CS8 | CREAD | HUPCL | CLOCAL;
-    serial_driver->flags = TTY_DRIVER_REAL_RAW;
-    tty_set_operations(serial_driver, &mgslpc_ops);
-
-    if ((rc = tty_register_driver(serial_driver)) < 0) {
-	    printk("%s(%d):Couldn't register serial driver\n",
-		   __FILE__,__LINE__);
-	    put_tty_driver(serial_driver);
-	    serial_driver = NULL;
-	    goto error;
-    }
-
-    printk("%s %s, tty major#%d\n",
-	   driver_name, driver_version,
-	   serial_driver->major);
-
-    return 0;
-
-error:
-    synclink_cs_cleanup();
-    return rc;
+	return 0;
+err_unreg_tty:
+	tty_unregister_driver(serial_driver);
+err_put_tty:
+	put_tty_driver(serial_driver);
+err:
+	return rc;
 }
 
 static void __exit synclink_cs_exit(void)
 {
-	synclink_cs_cleanup();
+	pcmcia_unregister_driver(&mgslpc_driver);
+	tty_unregister_driver(serial_driver);
+	put_tty_driver(serial_driver);
 }
 
 module_init(synclink_cs_init);
diff --git a/drivers/char/ttyprintk.c b/drivers/char/ttyprintk.c
index 46b77ed..af98f6d 100644
--- a/drivers/char/ttyprintk.c
+++ b/drivers/char/ttyprintk.c
@@ -67,7 +67,7 @@
 				tmp[tpk_curr + 1] = '\0';
 				printk(KERN_INFO "%s%s", tpk_tag, tmp);
 				tpk_curr = 0;
-				if (buf[i + 1] == '\n')
+				if ((i + 1) < count && buf[i + 1] == '\n')
 					i++;
 				break;
 			case '\n':
@@ -178,11 +178,17 @@
 static int __init ttyprintk_init(void)
 {
 	int ret = -ENOMEM;
-	void *rp;
 
-	ttyprintk_driver = alloc_tty_driver(1);
-	if (!ttyprintk_driver)
-		return ret;
+	tty_port_init(&tpk_port.port);
+	tpk_port.port.ops = &null_ops;
+	mutex_init(&tpk_port.port_write_mutex);
+
+	ttyprintk_driver = tty_alloc_driver(1,
+			TTY_DRIVER_RESET_TERMIOS |
+			TTY_DRIVER_REAL_RAW |
+			TTY_DRIVER_UNNUMBERED_NODE);
+	if (IS_ERR(ttyprintk_driver))
+		return PTR_ERR(ttyprintk_driver);
 
 	ttyprintk_driver->driver_name = "ttyprintk";
 	ttyprintk_driver->name = "ttyprintk";
@@ -191,9 +197,8 @@
 	ttyprintk_driver->type = TTY_DRIVER_TYPE_CONSOLE;
 	ttyprintk_driver->init_termios = tty_std_termios;
 	ttyprintk_driver->init_termios.c_oflag = OPOST | OCRNL | ONOCR | ONLRET;
-	ttyprintk_driver->flags = TTY_DRIVER_RESET_TERMIOS |
-		TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV;
 	tty_set_operations(ttyprintk_driver, &ttyprintk_ops);
+	tty_port_link_device(&tpk_port.port, ttyprintk_driver, 0);
 
 	ret = tty_register_driver(ttyprintk_driver);
 	if (ret < 0) {
@@ -201,22 +206,10 @@
 		goto error;
 	}
 
-	/* create our unnumbered device */
-	rp = device_create(tty_class, NULL, MKDEV(TTYAUX_MAJOR, 3), NULL,
-				ttyprintk_driver->name);
-	if (IS_ERR(rp)) {
-		printk(KERN_ERR "Couldn't create ttyprintk device\n");
-		ret = PTR_ERR(rp);
-		goto error;
-	}
-
-	tty_port_init(&tpk_port.port);
-	tpk_port.port.ops = &null_ops;
-	mutex_init(&tpk_port.port_write_mutex);
-
 	return 0;
 
 error:
+	tty_unregister_driver(ttyprintk_driver);
 	put_tty_driver(ttyprintk_driver);
 	ttyprintk_driver = NULL;
 	return ret;
diff --git a/drivers/cpufreq/omap-cpufreq.c b/drivers/cpufreq/omap-cpufreq.c
index 17fa04d0..b47034e 100644
--- a/drivers/cpufreq/omap-cpufreq.c
+++ b/drivers/cpufreq/omap-cpufreq.c
@@ -218,7 +218,7 @@
 
 	policy->cur = policy->min = policy->max = omap_getspeed(policy->cpu);
 
-	if (atomic_inc_return(&freq_table_users) == 1)
+	if (!freq_table)
 		result = opp_init_cpufreq_table(mpu_dev, &freq_table);
 
 	if (result) {
@@ -227,6 +227,8 @@
 		goto fail_ck;
 	}
 
+	atomic_inc_return(&freq_table_users);
+
 	result = cpufreq_frequency_table_cpuinfo(policy, freq_table);
 	if (result)
 		goto fail_table;
diff --git a/drivers/crypto/caam/jr.c b/drivers/crypto/caam/jr.c
index 53c8c51..93d1407 100644
--- a/drivers/crypto/caam/jr.c
+++ b/drivers/crypto/caam/jr.c
@@ -63,7 +63,7 @@
 
 		head = ACCESS_ONCE(jrp->head);
 
-		spin_lock_bh(&jrp->outlock);
+		spin_lock(&jrp->outlock);
 
 		sw_idx = tail = jrp->tail;
 		hw_idx = jrp->out_ring_read_index;
@@ -115,7 +115,7 @@
 			jrp->tail = tail;
 		}
 
-		spin_unlock_bh(&jrp->outlock);
+		spin_unlock(&jrp->outlock);
 
 		/* Finally, execute user's callback */
 		usercall(dev, userdesc, userstatus, userarg);
@@ -236,14 +236,14 @@
 		return -EIO;
 	}
 
-	spin_lock(&jrp->inplock);
+	spin_lock_bh(&jrp->inplock);
 
 	head = jrp->head;
 	tail = ACCESS_ONCE(jrp->tail);
 
 	if (!rd_reg32(&jrp->rregs->inpring_avail) ||
 	    CIRC_SPACE(head, tail, JOBR_DEPTH) <= 0) {
-		spin_unlock(&jrp->inplock);
+		spin_unlock_bh(&jrp->inplock);
 		dma_unmap_single(dev, desc_dma, desc_size, DMA_TO_DEVICE);
 		return -EBUSY;
 	}
@@ -265,7 +265,7 @@
 
 	wr_reg32(&jrp->rregs->inpring_jobadd, 1);
 
-	spin_unlock(&jrp->inplock);
+	spin_unlock_bh(&jrp->inplock);
 
 	return 0;
 }
diff --git a/drivers/crypto/hifn_795x.c b/drivers/crypto/hifn_795x.c
index c9c4bef..df14358 100644
--- a/drivers/crypto/hifn_795x.c
+++ b/drivers/crypto/hifn_795x.c
@@ -821,8 +821,8 @@
 	/*
 	 * We must wait at least 256 Pk_clk cycles between two reads of the rng.
 	 */
-	dev->rng_wait_time	= DIV_ROUND_UP(NSEC_PER_SEC, dev->pk_clk_freq) *
-				  256;
+	dev->rng_wait_time	= DIV_ROUND_UP_ULL(NSEC_PER_SEC,
+						   dev->pk_clk_freq) * 256;
 
 	dev->rng.name		= dev->name;
 	dev->rng.data_present	= hifn_rng_data_present,
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index b16c8a7..ba7926f5 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -294,7 +294,7 @@
 
 config GPIO_MC9S08DZ60
 	bool "MX35 3DS BOARD MC9S08DZ60 GPIO functions"
-	depends on I2C && MACH_MX35_3DS
+	depends on I2C=y && MACH_MX35_3DS
 	help
 	  Select this to enable the MC9S08DZ60 GPIO driver
 
diff --git a/drivers/gpio/gpio-em.c b/drivers/gpio/gpio-em.c
index ae37181..ec48ed5 100644
--- a/drivers/gpio/gpio-em.c
+++ b/drivers/gpio/gpio-em.c
@@ -247,9 +247,9 @@
 
 	p->irq_base = irq_alloc_descs(pdata->irq_base, 0,
 				      pdata->number_of_pins, numa_node_id());
-	if (IS_ERR_VALUE(p->irq_base)) {
+	if (p->irq_base < 0) {
 		dev_err(&pdev->dev, "cannot get irq_desc\n");
-		return -ENXIO;
+		return p->irq_base;
 	}
 	pr_debug("gio: hw base = %d, nr = %d, sw base = %d\n",
 		 pdata->gpio_base, pdata->number_of_pins, p->irq_base);
diff --git a/drivers/gpio/gpio-rdc321x.c b/drivers/gpio/gpio-rdc321x.c
index e97016a..b62d443 100644
--- a/drivers/gpio/gpio-rdc321x.c
+++ b/drivers/gpio/gpio-rdc321x.c
@@ -170,6 +170,7 @@
 	rdc321x_gpio_dev->reg2_data_base = r->start + 0x4;
 
 	rdc321x_gpio_dev->chip.label = "rdc321x-gpio";
+	rdc321x_gpio_dev->chip.owner = THIS_MODULE;
 	rdc321x_gpio_dev->chip.direction_input = rdc_gpio_direction_input;
 	rdc321x_gpio_dev->chip.direction_output = rdc_gpio_config;
 	rdc321x_gpio_dev->chip.get = rdc_gpio_get_value;
diff --git a/drivers/gpio/gpiolib-of.c b/drivers/gpio/gpiolib-of.c
index a18c4aa..f1a4599 100644
--- a/drivers/gpio/gpiolib-of.c
+++ b/drivers/gpio/gpiolib-of.c
@@ -82,7 +82,7 @@
 	gpiochip_find(&gg_data, of_gpiochip_find_and_xlate);
 
 	of_node_put(gg_data.gpiospec.np);
-	pr_debug("%s exited with status %d\n", __func__, ret);
+	pr_debug("%s exited with status %d\n", __func__, gg_data.out_gpio);
 	return gg_data.out_gpio;
 }
 EXPORT_SYMBOL(of_get_named_gpio_flags);
diff --git a/drivers/gpu/drm/drm_crtc.c b/drivers/gpu/drm/drm_crtc.c
index 08a7aa7..6fbfc24 100644
--- a/drivers/gpu/drm/drm_crtc.c
+++ b/drivers/gpu/drm/drm_crtc.c
@@ -1981,7 +1981,7 @@
 	if (!drm_core_check_feature(dev, DRIVER_MODESET))
 		return -EINVAL;
 
-	if (!req->flags)
+	if (!req->flags || (~DRM_MODE_CURSOR_FLAGS & req->flags))
 		return -EINVAL;
 
 	mutex_lock(&dev->mode_config.mutex);
diff --git a/drivers/gpu/drm/drm_edid.c b/drivers/gpu/drm/drm_edid.c
index a8743c3..b7ee230 100644
--- a/drivers/gpu/drm/drm_edid.c
+++ b/drivers/gpu/drm/drm_edid.c
@@ -87,6 +87,9 @@
 	int product_id;
 	u32 quirks;
 } edid_quirk_list[] = {
+	/* ASUS VW222S */
+	{ "ACI", 0x22a2, EDID_QUIRK_FORCE_REDUCED_BLANKING },
+
 	/* Acer AL1706 */
 	{ "ACR", 44358, EDID_QUIRK_PREFER_LARGE_60 },
 	/* Acer F51 */
diff --git a/drivers/gpu/drm/gma500/psb_intel_display.c b/drivers/gpu/drm/gma500/psb_intel_display.c
index 30dc22a..8033526 100644
--- a/drivers/gpu/drm/gma500/psb_intel_display.c
+++ b/drivers/gpu/drm/gma500/psb_intel_display.c
@@ -1362,6 +1362,9 @@
 	    (struct drm_connector **) (psb_intel_crtc + 1);
 	psb_intel_crtc->mode_set.num_connectors = 0;
 	psb_intel_cursor_init(dev, psb_intel_crtc);
+
+	/* Set to true so that the pipe is forced off on initial config. */
+	psb_intel_crtc->active = true;
 }
 
 int psb_intel_get_pipe_from_crtc_id(struct drm_device *dev, void *data,
diff --git a/drivers/gpu/drm/i915/i915_gem_gtt.c b/drivers/gpu/drm/i915/i915_gem_gtt.c
index d9a5372..60815b8 100644
--- a/drivers/gpu/drm/i915/i915_gem_gtt.c
+++ b/drivers/gpu/drm/i915/i915_gem_gtt.c
@@ -72,7 +72,7 @@
 	/* ppgtt PDEs reside in the global gtt pagetable, which has 512*1024
 	 * entries. For aliasing ppgtt support we just steal them at the end for
 	 * now. */
-	first_pd_entry_in_global_pt = 512*1024 - I915_PPGTT_PD_ENTRIES;
+	first_pd_entry_in_global_pt = dev_priv->mm.gtt->gtt_total_entries - I915_PPGTT_PD_ENTRIES;
 
 	ppgtt = kzalloc(sizeof(*ppgtt), GFP_KERNEL);
 	if (!ppgtt)
diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index a69a3d0..2dfa6cf 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -1384,7 +1384,7 @@
 				     enum pipe pipe, int reg)
 {
 	u32 val = I915_READ(reg);
-	WARN(hdmi_pipe_enabled(dev_priv, val, pipe),
+	WARN(hdmi_pipe_enabled(dev_priv, pipe, val),
 	     "PCH HDMI (0x%08x) enabled on transcoder %c, should be disabled\n",
 	     reg, pipe_name(pipe));
 
@@ -1404,13 +1404,13 @@
 
 	reg = PCH_ADPA;
 	val = I915_READ(reg);
-	WARN(adpa_pipe_enabled(dev_priv, val, pipe),
+	WARN(adpa_pipe_enabled(dev_priv, pipe, val),
 	     "PCH VGA enabled on transcoder %c, should be disabled\n",
 	     pipe_name(pipe));
 
 	reg = PCH_LVDS;
 	val = I915_READ(reg);
-	WARN(lvds_pipe_enabled(dev_priv, val, pipe),
+	WARN(lvds_pipe_enabled(dev_priv, pipe, val),
 	     "PCH LVDS enabled on transcoder %c, should be disabled\n",
 	     pipe_name(pipe));
 
@@ -1872,7 +1872,7 @@
 			     enum pipe pipe, int reg)
 {
 	u32 val = I915_READ(reg);
-	if (hdmi_pipe_enabled(dev_priv, val, pipe)) {
+	if (hdmi_pipe_enabled(dev_priv, pipe, val)) {
 		DRM_DEBUG_KMS("Disabling pch HDMI %x on pipe %d\n",
 			      reg, pipe);
 		I915_WRITE(reg, val & ~PORT_ENABLE);
@@ -1894,12 +1894,12 @@
 
 	reg = PCH_ADPA;
 	val = I915_READ(reg);
-	if (adpa_pipe_enabled(dev_priv, val, pipe))
+	if (adpa_pipe_enabled(dev_priv, pipe, val))
 		I915_WRITE(reg, val & ~ADPA_DAC_ENABLE);
 
 	reg = PCH_LVDS;
 	val = I915_READ(reg);
-	if (lvds_pipe_enabled(dev_priv, val, pipe)) {
+	if (lvds_pipe_enabled(dev_priv, pipe, val)) {
 		DRM_DEBUG_KMS("disable lvds on pipe %d val 0x%08x\n", pipe, val);
 		I915_WRITE(reg, val & ~LVDS_PORT_EN);
 		POSTING_READ(reg);
diff --git a/drivers/gpu/drm/i915/intel_lvds.c b/drivers/gpu/drm/i915/intel_lvds.c
index e05c0d3..e9a6f6a 100644
--- a/drivers/gpu/drm/i915/intel_lvds.c
+++ b/drivers/gpu/drm/i915/intel_lvds.c
@@ -780,6 +780,14 @@
 			DMI_MATCH(DMI_BOARD_NAME, "ZBOXSD-ID12/ID13"),
 		},
 	},
+	{
+		.callback = intel_no_lvds_dmi_callback,
+		.ident = "Gigabyte GA-D525TUD",
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "Gigabyte Technology Co., Ltd."),
+			DMI_MATCH(DMI_BOARD_NAME, "D525TUD"),
+		},
+	},
 
 	{ }	/* terminating entry */
 };
diff --git a/drivers/gpu/drm/i915/intel_sprite.c b/drivers/gpu/drm/i915/intel_sprite.c
index cc8df4d..7644f31 100644
--- a/drivers/gpu/drm/i915/intel_sprite.c
+++ b/drivers/gpu/drm/i915/intel_sprite.c
@@ -60,11 +60,11 @@
 
 	switch (fb->pixel_format) {
 	case DRM_FORMAT_XBGR8888:
-		sprctl |= SPRITE_FORMAT_RGBX888;
+		sprctl |= SPRITE_FORMAT_RGBX888 | SPRITE_RGB_ORDER_RGBX;
 		pixel_size = 4;
 		break;
 	case DRM_FORMAT_XRGB8888:
-		sprctl |= SPRITE_FORMAT_RGBX888 | SPRITE_RGB_ORDER_RGBX;
+		sprctl |= SPRITE_FORMAT_RGBX888;
 		pixel_size = 4;
 		break;
 	case DRM_FORMAT_YUYV:
diff --git a/drivers/gpu/drm/nouveau/nouveau_state.c b/drivers/gpu/drm/nouveau/nouveau_state.c
index 1866dbb..c610144 100644
--- a/drivers/gpu/drm/nouveau/nouveau_state.c
+++ b/drivers/gpu/drm/nouveau/nouveau_state.c
@@ -736,9 +736,11 @@
 			}
 			break;
 		case NV_C0:
-			nvc0_copy_create(dev, 1);
+			if (!(nv_rd32(dev, 0x022500) & 0x00000200))
+				nvc0_copy_create(dev, 1);
 		case NV_D0:
-			nvc0_copy_create(dev, 0);
+			if (!(nv_rd32(dev, 0x022500) & 0x00000100))
+				nvc0_copy_create(dev, 0);
 			break;
 		default:
 			break;
diff --git a/drivers/gpu/drm/radeon/atombios_crtc.c b/drivers/gpu/drm/radeon/atombios_crtc.c
index f4d4505..2817101 100644
--- a/drivers/gpu/drm/radeon/atombios_crtc.c
+++ b/drivers/gpu/drm/radeon/atombios_crtc.c
@@ -258,7 +258,6 @@
 		radeon_crtc->enabled = true;
 		/* adjust pm to dpms changes BEFORE enabling crtcs */
 		radeon_pm_compute_clocks(rdev);
-		/* disable crtc pair power gating before programming */
 		if (ASIC_IS_DCE6(rdev) && !radeon_crtc->in_mode_set)
 			atombios_powergate_crtc(crtc, ATOM_DISABLE);
 		atombios_enable_crtc(crtc, ATOM_ENABLE);
@@ -278,25 +277,8 @@
 			atombios_enable_crtc_memreq(crtc, ATOM_DISABLE);
 		atombios_enable_crtc(crtc, ATOM_DISABLE);
 		radeon_crtc->enabled = false;
-		/* power gating is per-pair */
-		if (ASIC_IS_DCE6(rdev) && !radeon_crtc->in_mode_set) {
-			struct drm_crtc *other_crtc;
-			struct radeon_crtc *other_radeon_crtc;
-			list_for_each_entry(other_crtc, &rdev->ddev->mode_config.crtc_list, head) {
-				other_radeon_crtc = to_radeon_crtc(other_crtc);
-				if (((radeon_crtc->crtc_id == 0) && (other_radeon_crtc->crtc_id == 1)) ||
-				    ((radeon_crtc->crtc_id == 1) && (other_radeon_crtc->crtc_id == 0)) ||
-				    ((radeon_crtc->crtc_id == 2) && (other_radeon_crtc->crtc_id == 3)) ||
-				    ((radeon_crtc->crtc_id == 3) && (other_radeon_crtc->crtc_id == 2)) ||
-				    ((radeon_crtc->crtc_id == 4) && (other_radeon_crtc->crtc_id == 5)) ||
-				    ((radeon_crtc->crtc_id == 5) && (other_radeon_crtc->crtc_id == 4))) {
-					/* if both crtcs in the pair are off, enable power gating */
-					if (other_radeon_crtc->enabled == false)
-						atombios_powergate_crtc(crtc, ATOM_ENABLE);
-					break;
-				}
-			}
-		}
+		if (ASIC_IS_DCE6(rdev) && !radeon_crtc->in_mode_set)
+			atombios_powergate_crtc(crtc, ATOM_ENABLE);
 		/* adjust pm to dpms changes AFTER disabling crtcs */
 		radeon_pm_compute_clocks(rdev);
 		break;
@@ -1682,9 +1664,22 @@
 	struct drm_device *dev = crtc->dev;
 	struct radeon_device *rdev = dev->dev_private;
 	struct radeon_atom_ss ss;
+	int i;
 
 	atombios_crtc_dpms(crtc, DRM_MODE_DPMS_OFF);
 
+	for (i = 0; i < rdev->num_crtc; i++) {
+		if (rdev->mode_info.crtcs[i] &&
+		    rdev->mode_info.crtcs[i]->enabled &&
+		    i != radeon_crtc->crtc_id &&
+		    radeon_crtc->pll_id == rdev->mode_info.crtcs[i]->pll_id) {
+			/* one other crtc is using this pll don't turn
+			 * off the pll
+			 */
+			goto done;
+		}
+	}
+
 	switch (radeon_crtc->pll_id) {
 	case ATOM_PPLL1:
 	case ATOM_PPLL2:
@@ -1701,6 +1696,7 @@
 	default:
 		break;
 	}
+done:
 	radeon_crtc->pll_id = -1;
 }
 
diff --git a/drivers/gpu/drm/radeon/atombios_dp.c b/drivers/gpu/drm/radeon/atombios_dp.c
index 7712cf5..3623b98 100644
--- a/drivers/gpu/drm/radeon/atombios_dp.c
+++ b/drivers/gpu/drm/radeon/atombios_dp.c
@@ -577,30 +577,25 @@
 	struct radeon_device *rdev = dev->dev_private;
 	struct radeon_connector *radeon_connector = to_radeon_connector(connector);
 	int panel_mode = DP_PANEL_MODE_EXTERNAL_DP_MODE;
+	u16 dp_bridge = radeon_connector_encoder_get_dp_bridge_encoder_id(connector);
+	u8 tmp;
 
 	if (!ASIC_IS_DCE4(rdev))
 		return panel_mode;
 
-	if (radeon_connector_encoder_get_dp_bridge_encoder_id(connector) ==
-	    ENCODER_OBJECT_ID_NUTMEG)
-		panel_mode = DP_PANEL_MODE_INTERNAL_DP1_MODE;
-	else if (radeon_connector_encoder_get_dp_bridge_encoder_id(connector) ==
-		 ENCODER_OBJECT_ID_TRAVIS) {
-		u8 id[6];
-		int i;
-		for (i = 0; i < 6; i++)
-			id[i] = radeon_read_dpcd_reg(radeon_connector, 0x503 + i);
-		if (id[0] == 0x73 &&
-		    id[1] == 0x69 &&
-		    id[2] == 0x76 &&
-		    id[3] == 0x61 &&
-		    id[4] == 0x72 &&
-		    id[5] == 0x54)
+	if (dp_bridge != ENCODER_OBJECT_ID_NONE) {
+		/* DP bridge chips */
+		tmp = radeon_read_dpcd_reg(radeon_connector, DP_EDP_CONFIGURATION_CAP);
+		if (tmp & 1)
+			panel_mode = DP_PANEL_MODE_INTERNAL_DP2_MODE;
+		else if ((dp_bridge == ENCODER_OBJECT_ID_NUTMEG) ||
+			 (dp_bridge == ENCODER_OBJECT_ID_TRAVIS))
 			panel_mode = DP_PANEL_MODE_INTERNAL_DP1_MODE;
 		else
-			panel_mode = DP_PANEL_MODE_INTERNAL_DP2_MODE;
+			panel_mode = DP_PANEL_MODE_EXTERNAL_DP_MODE;
 	} else if (connector->connector_type == DRM_MODE_CONNECTOR_eDP) {
-		u8 tmp = radeon_read_dpcd_reg(radeon_connector, DP_EDP_CONFIGURATION_CAP);
+		/* eDP */
+		tmp = radeon_read_dpcd_reg(radeon_connector, DP_EDP_CONFIGURATION_CAP);
 		if (tmp & 1)
 			panel_mode = DP_PANEL_MODE_INTERNAL_DP2_MODE;
 	}
diff --git a/drivers/gpu/drm/radeon/atombios_encoders.c b/drivers/gpu/drm/radeon/atombios_encoders.c
index f9bc27f..6e8803a 100644
--- a/drivers/gpu/drm/radeon/atombios_encoders.c
+++ b/drivers/gpu/drm/radeon/atombios_encoders.c
@@ -1379,6 +1379,8 @@
 	struct drm_device *dev = encoder->dev;
 	struct radeon_device *rdev = dev->dev_private;
 	struct radeon_encoder *radeon_encoder = to_radeon_encoder(encoder);
+	struct drm_encoder *ext_encoder = radeon_get_external_encoder(encoder);
+	struct radeon_encoder_atom_dig *dig = radeon_encoder->enc_priv;
 	struct drm_connector *connector = radeon_get_connector_for_encoder(encoder);
 	struct radeon_connector *radeon_connector = NULL;
 	struct radeon_connector_atom_dig *radeon_dig_connector = NULL;
@@ -1390,19 +1392,37 @@
 
 	switch (mode) {
 	case DRM_MODE_DPMS_ON:
-		/* some early dce3.2 boards have a bug in their transmitter control table */
-		if ((rdev->family == CHIP_RV710) || (rdev->family == CHIP_RV730) ||
-		    ASIC_IS_DCE41(rdev) || ASIC_IS_DCE5(rdev)) {
-			if (ASIC_IS_DCE6(rdev)) {
-				/* It seems we need to call ATOM_ENCODER_CMD_SETUP again
-				 * before reenabling encoder on DPMS ON, otherwise we never
-				 * get picture
-				 */
-				atombios_dig_encoder_setup(encoder, ATOM_ENCODER_CMD_SETUP, 0);
+		if (ASIC_IS_DCE41(rdev) || ASIC_IS_DCE5(rdev)) {
+			if (!connector)
+				dig->panel_mode = DP_PANEL_MODE_EXTERNAL_DP_MODE;
+			else
+				dig->panel_mode = radeon_dp_get_panel_mode(encoder, connector);
+
+			/* setup and enable the encoder */
+			atombios_dig_encoder_setup(encoder, ATOM_ENCODER_CMD_SETUP, 0);
+			atombios_dig_encoder_setup(encoder,
+						   ATOM_ENCODER_CMD_SETUP_PANEL_MODE,
+						   dig->panel_mode);
+			if (ext_encoder) {
+				if (ASIC_IS_DCE41(rdev) || ASIC_IS_DCE61(rdev))
+					atombios_external_encoder_setup(encoder, ext_encoder,
+									EXTERNAL_ENCODER_ACTION_V3_ENCODER_SETUP);
 			}
 			atombios_dig_transmitter_setup(encoder, ATOM_TRANSMITTER_ACTION_ENABLE, 0, 0);
-		} else {
+		} else if (ASIC_IS_DCE4(rdev)) {
+			/* setup and enable the encoder */
+			atombios_dig_encoder_setup(encoder, ATOM_ENCODER_CMD_SETUP, 0);
+			/* enable the transmitter */
+			atombios_dig_transmitter_setup(encoder, ATOM_TRANSMITTER_ACTION_ENABLE, 0, 0);
 			atombios_dig_transmitter_setup(encoder, ATOM_TRANSMITTER_ACTION_ENABLE_OUTPUT, 0, 0);
+		} else {
+			/* setup and enable the encoder and transmitter */
+			atombios_dig_encoder_setup(encoder, ATOM_ENABLE, 0);
+			atombios_dig_transmitter_setup(encoder, ATOM_TRANSMITTER_ACTION_SETUP, 0, 0);
+			atombios_dig_transmitter_setup(encoder, ATOM_TRANSMITTER_ACTION_ENABLE, 0, 0);
+			/* some early dce3.2 boards have a bug in their transmitter control table */
+			if ((rdev->family != CHIP_RV710) || (rdev->family != CHIP_RV730))
+				atombios_dig_transmitter_setup(encoder, ATOM_TRANSMITTER_ACTION_ENABLE_OUTPUT, 0, 0);
 		}
 		if (ENCODER_MODE_IS_DP(atombios_get_encoder_mode(encoder)) && connector) {
 			if (connector->connector_type == DRM_MODE_CONNECTOR_eDP) {
@@ -1420,10 +1440,19 @@
 	case DRM_MODE_DPMS_STANDBY:
 	case DRM_MODE_DPMS_SUSPEND:
 	case DRM_MODE_DPMS_OFF:
-		if (ASIC_IS_DCE41(rdev) || ASIC_IS_DCE5(rdev))
+		if (ASIC_IS_DCE41(rdev) || ASIC_IS_DCE5(rdev)) {
+			/* disable the transmitter */
 			atombios_dig_transmitter_setup(encoder, ATOM_TRANSMITTER_ACTION_DISABLE, 0, 0);
-		else
+		} else if (ASIC_IS_DCE4(rdev)) {
+			/* disable the transmitter */
 			atombios_dig_transmitter_setup(encoder, ATOM_TRANSMITTER_ACTION_DISABLE_OUTPUT, 0, 0);
+			atombios_dig_transmitter_setup(encoder, ATOM_TRANSMITTER_ACTION_DISABLE, 0, 0);
+		} else {
+			/* disable the encoder and transmitter */
+			atombios_dig_transmitter_setup(encoder, ATOM_TRANSMITTER_ACTION_DISABLE_OUTPUT, 0, 0);
+			atombios_dig_transmitter_setup(encoder, ATOM_TRANSMITTER_ACTION_DISABLE, 0, 0);
+			atombios_dig_encoder_setup(encoder, ATOM_DISABLE, 0);
+		}
 		if (ENCODER_MODE_IS_DP(atombios_get_encoder_mode(encoder)) && connector) {
 			if (ASIC_IS_DCE4(rdev))
 				atombios_dig_encoder_setup(encoder, ATOM_ENCODER_CMD_DP_VIDEO_OFF, 0);
@@ -1740,13 +1769,34 @@
 	struct radeon_crtc *radeon_crtc = to_radeon_crtc(encoder->crtc);
 	struct radeon_encoder *radeon_encoder = to_radeon_encoder(encoder);
 	struct drm_encoder *test_encoder;
-	struct radeon_encoder_atom_dig *dig;
+	struct radeon_encoder_atom_dig *dig = radeon_encoder->enc_priv;
 	uint32_t dig_enc_in_use = 0;
 
-	/* DCE4/5 */
-	if (ASIC_IS_DCE4(rdev)) {
-		dig = radeon_encoder->enc_priv;
-		if (ASIC_IS_DCE41(rdev)) {
+	if (ASIC_IS_DCE6(rdev)) {
+		/* DCE6 */
+		switch (radeon_encoder->encoder_id) {
+		case ENCODER_OBJECT_ID_INTERNAL_UNIPHY:
+			if (dig->linkb)
+				return 1;
+			else
+				return 0;
+			break;
+		case ENCODER_OBJECT_ID_INTERNAL_UNIPHY1:
+			if (dig->linkb)
+				return 3;
+			else
+				return 2;
+			break;
+		case ENCODER_OBJECT_ID_INTERNAL_UNIPHY2:
+			if (dig->linkb)
+				return 5;
+			else
+				return 4;
+			break;
+		}
+	} else if (ASIC_IS_DCE4(rdev)) {
+		/* DCE4/5 */
+		if (ASIC_IS_DCE41(rdev) && !ASIC_IS_DCE61(rdev)) {
 			/* ontario follows DCE4 */
 			if (rdev->family == CHIP_PALM) {
 				if (dig->linkb)
@@ -1848,10 +1898,12 @@
 	struct drm_device *dev = encoder->dev;
 	struct radeon_device *rdev = dev->dev_private;
 	struct radeon_encoder *radeon_encoder = to_radeon_encoder(encoder);
-	struct drm_encoder *ext_encoder = radeon_get_external_encoder(encoder);
 
 	radeon_encoder->pixel_clock = adjusted_mode->clock;
 
+	/* need to call this here rather than in prepare() since we need some crtc info */
+	radeon_atom_encoder_dpms(encoder, DRM_MODE_DPMS_OFF);
+
 	if (ASIC_IS_AVIVO(rdev) && !ASIC_IS_DCE4(rdev)) {
 		if (radeon_encoder->active_device & (ATOM_DEVICE_CV_SUPPORT | ATOM_DEVICE_TV_SUPPORT))
 			atombios_yuv_setup(encoder, true);
@@ -1870,38 +1922,7 @@
 	case ENCODER_OBJECT_ID_INTERNAL_UNIPHY1:
 	case ENCODER_OBJECT_ID_INTERNAL_UNIPHY2:
 	case ENCODER_OBJECT_ID_INTERNAL_KLDSCP_LVTMA:
-		if (ASIC_IS_DCE41(rdev) || ASIC_IS_DCE5(rdev)) {
-			struct drm_connector *connector = radeon_get_connector_for_encoder(encoder);
-			struct radeon_encoder_atom_dig *dig = radeon_encoder->enc_priv;
-
-			if (!connector)
-				dig->panel_mode = DP_PANEL_MODE_EXTERNAL_DP_MODE;
-			else
-				dig->panel_mode = radeon_dp_get_panel_mode(encoder, connector);
-
-			/* setup and enable the encoder */
-			atombios_dig_encoder_setup(encoder, ATOM_ENCODER_CMD_SETUP, 0);
-			atombios_dig_encoder_setup(encoder,
-						   ATOM_ENCODER_CMD_SETUP_PANEL_MODE,
-						   dig->panel_mode);
-		} else if (ASIC_IS_DCE4(rdev)) {
-			/* disable the transmitter */
-			atombios_dig_transmitter_setup(encoder, ATOM_TRANSMITTER_ACTION_DISABLE, 0, 0);
-			/* setup and enable the encoder */
-			atombios_dig_encoder_setup(encoder, ATOM_ENCODER_CMD_SETUP, 0);
-
-			/* enable the transmitter */
-			atombios_dig_transmitter_setup(encoder, ATOM_TRANSMITTER_ACTION_ENABLE, 0, 0);
-		} else {
-			/* disable the encoder and transmitter */
-			atombios_dig_transmitter_setup(encoder, ATOM_TRANSMITTER_ACTION_DISABLE, 0, 0);
-			atombios_dig_encoder_setup(encoder, ATOM_DISABLE, 0);
-
-			/* setup and enable the encoder and transmitter */
-			atombios_dig_encoder_setup(encoder, ATOM_ENABLE, 0);
-			atombios_dig_transmitter_setup(encoder, ATOM_TRANSMITTER_ACTION_SETUP, 0, 0);
-			atombios_dig_transmitter_setup(encoder, ATOM_TRANSMITTER_ACTION_ENABLE, 0, 0);
-		}
+		/* handled in dpms */
 		break;
 	case ENCODER_OBJECT_ID_INTERNAL_DDI:
 	case ENCODER_OBJECT_ID_INTERNAL_DVO1:
@@ -1922,14 +1943,6 @@
 		break;
 	}
 
-	if (ext_encoder) {
-		if (ASIC_IS_DCE41(rdev) || ASIC_IS_DCE61(rdev))
-			atombios_external_encoder_setup(encoder, ext_encoder,
-							EXTERNAL_ENCODER_ACTION_V3_ENCODER_SETUP);
-		else
-			atombios_external_encoder_setup(encoder, ext_encoder, ATOM_ENABLE);
-	}
-
 	atombios_apply_encoder_quirks(encoder, adjusted_mode);
 
 	if (atombios_get_encoder_mode(encoder) == ATOM_ENCODER_MODE_HDMI) {
@@ -2116,7 +2129,6 @@
 	}
 
 	radeon_atom_output_lock(encoder, true);
-	radeon_atom_encoder_dpms(encoder, DRM_MODE_DPMS_OFF);
 
 	if (connector) {
 		struct radeon_connector *radeon_connector = to_radeon_connector(connector);
@@ -2137,6 +2149,7 @@
 
 static void radeon_atom_encoder_commit(struct drm_encoder *encoder)
 {
+	/* need to call this here as we need the crtc set up */
 	radeon_atom_encoder_dpms(encoder, DRM_MODE_DPMS_ON);
 	radeon_atom_output_lock(encoder, false);
 }
@@ -2177,14 +2190,7 @@
 	case ENCODER_OBJECT_ID_INTERNAL_UNIPHY1:
 	case ENCODER_OBJECT_ID_INTERNAL_UNIPHY2:
 	case ENCODER_OBJECT_ID_INTERNAL_KLDSCP_LVTMA:
-		if (ASIC_IS_DCE4(rdev))
-			/* disable the transmitter */
-			atombios_dig_transmitter_setup(encoder, ATOM_TRANSMITTER_ACTION_DISABLE, 0, 0);
-		else {
-			/* disable the encoder and transmitter */
-			atombios_dig_transmitter_setup(encoder, ATOM_TRANSMITTER_ACTION_DISABLE, 0, 0);
-			atombios_dig_encoder_setup(encoder, ATOM_DISABLE, 0);
-		}
+		/* handled in dpms */
 		break;
 	case ENCODER_OBJECT_ID_INTERNAL_DDI:
 	case ENCODER_OBJECT_ID_INTERNAL_DVO1:
diff --git a/drivers/gpu/drm/radeon/r600_cs.c b/drivers/gpu/drm/radeon/r600_cs.c
index ab74e6b..f37676d 100644
--- a/drivers/gpu/drm/radeon/r600_cs.c
+++ b/drivers/gpu/drm/radeon/r600_cs.c
@@ -63,6 +63,7 @@
 	u32			cb_color_size_idx[8]; /* unused */
 	u32			cb_target_mask;
 	u32			cb_shader_mask;  /* unused */
+	bool			is_resolve;
 	u32			cb_color_size[8];
 	u32			vgt_strmout_en;
 	u32			vgt_strmout_buffer_en;
@@ -315,7 +316,15 @@
 		track->cb_color_bo[i] = NULL;
 		track->cb_color_bo_offset[i] = 0xFFFFFFFF;
 		track->cb_color_bo_mc[i] = 0xFFFFFFFF;
+		track->cb_color_frag_bo[i] = NULL;
+		track->cb_color_frag_offset[i] = 0xFFFFFFFF;
+		track->cb_color_tile_bo[i] = NULL;
+		track->cb_color_tile_offset[i] = 0xFFFFFFFF;
+		track->cb_color_mask[i] = 0xFFFFFFFF;
 	}
+	track->is_resolve = false;
+	track->nsamples = 16;
+	track->log_nsamples = 4;
 	track->cb_target_mask = 0xFFFFFFFF;
 	track->cb_shader_mask = 0xFFFFFFFF;
 	track->cb_dirty = true;
@@ -352,6 +361,8 @@
 	volatile u32 *ib = p->ib.ptr;
 	unsigned array_mode;
 	u32 format;
+	/* When resolve is used, the second colorbuffer has always 1 sample. */
+	unsigned nsamples = track->is_resolve && i == 1 ? 1 : track->nsamples;
 
 	size = radeon_bo_size(track->cb_color_bo[i]) - track->cb_color_bo_offset[i];
 	format = G_0280A0_FORMAT(track->cb_color_info[i]);
@@ -375,7 +386,7 @@
 	array_check.group_size = track->group_size;
 	array_check.nbanks = track->nbanks;
 	array_check.npipes = track->npipes;
-	array_check.nsamples = track->nsamples;
+	array_check.nsamples = nsamples;
 	array_check.blocksize = r600_fmt_get_blocksize(format);
 	if (r600_get_array_mode_alignment(&array_check,
 					  &pitch_align, &height_align, &depth_align, &base_align)) {
@@ -421,7 +432,7 @@
 
 	/* check offset */
 	tmp = r600_fmt_get_nblocksy(format, height) * r600_fmt_get_nblocksx(format, pitch) *
-	      r600_fmt_get_blocksize(format) * track->nsamples;
+	      r600_fmt_get_blocksize(format) * nsamples;
 	switch (array_mode) {
 	default:
 	case V_0280A0_ARRAY_LINEAR_GENERAL:
@@ -792,6 +803,12 @@
 	 */
 	if (track->cb_dirty) {
 		tmp = track->cb_target_mask;
+
+		/* We must check both colorbuffers for RESOLVE. */
+		if (track->is_resolve) {
+			tmp |= 0xff;
+		}
+
 		for (i = 0; i < 8; i++) {
 			if ((tmp >> (i * 4)) & 0xF) {
 				/* at least one component is enabled */
@@ -1281,6 +1298,11 @@
 		track->nsamples = 1 << tmp;
 		track->cb_dirty = true;
 		break;
+	case R_028808_CB_COLOR_CONTROL:
+		tmp = G_028808_SPECIAL_OP(radeon_get_ib_value(p, idx));
+		track->is_resolve = tmp == V_028808_SPECIAL_RESOLVE_BOX;
+		track->cb_dirty = true;
+		break;
 	case R_0280A0_CB_COLOR0_INFO:
 	case R_0280A4_CB_COLOR1_INFO:
 	case R_0280A8_CB_COLOR2_INFO:
@@ -1416,7 +1438,7 @@
 	case R_028118_CB_COLOR6_MASK:
 	case R_02811C_CB_COLOR7_MASK:
 		tmp = (reg - R_028100_CB_COLOR0_MASK) / 4;
-		track->cb_color_mask[tmp] = ib[idx];
+		track->cb_color_mask[tmp] = radeon_get_ib_value(p, idx);
 		if (G_0280A0_TILE_MODE(track->cb_color_info[tmp])) {
 			track->cb_dirty = true;
 		}
diff --git a/drivers/gpu/drm/radeon/r600d.h b/drivers/gpu/drm/radeon/r600d.h
index bdb69a6..fa6f370 100644
--- a/drivers/gpu/drm/radeon/r600d.h
+++ b/drivers/gpu/drm/radeon/r600d.h
@@ -66,6 +66,14 @@
 #define	CC_RB_BACKEND_DISABLE				0x98F4
 #define		BACKEND_DISABLE(x)				((x) << 16)
 
+#define R_028808_CB_COLOR_CONTROL			0x28808
+#define   S_028808_SPECIAL_OP(x)                       (((x) & 0x7) << 4)
+#define   G_028808_SPECIAL_OP(x)                       (((x) >> 4) & 0x7)
+#define   C_028808_SPECIAL_OP                          0xFFFFFF8F
+#define     V_028808_SPECIAL_NORMAL                     0x00
+#define     V_028808_SPECIAL_DISABLE                    0x01
+#define     V_028808_SPECIAL_RESOLVE_BOX                0x07
+
 #define	CB_COLOR0_BASE					0x28040
 #define	CB_COLOR1_BASE					0x28044
 #define	CB_COLOR2_BASE					0x28048
diff --git a/drivers/gpu/drm/radeon/radeon_device.c b/drivers/gpu/drm/radeon/radeon_device.c
index d2e2438..7a3daeb 100644
--- a/drivers/gpu/drm/radeon/radeon_device.c
+++ b/drivers/gpu/drm/radeon/radeon_device.c
@@ -1051,7 +1051,7 @@
 	if (rdev->flags & RADEON_IS_AGP)
 		rdev->need_dma32 = true;
 	if ((rdev->flags & RADEON_IS_PCI) &&
-	    (rdev->family < CHIP_RS400))
+	    (rdev->family <= CHIP_RS740))
 		rdev->need_dma32 = true;
 
 	dma_bits = rdev->need_dma32 ? 32 : 40;
@@ -1346,12 +1346,15 @@
 		for (i = 0; i < RADEON_NUM_RINGS; ++i) {
 			radeon_ring_restore(rdev, &rdev->ring[i],
 					    ring_sizes[i], ring_data[i]);
+			ring_sizes[i] = 0;
+			ring_data[i] = NULL;
 		}
 
 		r = radeon_ib_ring_tests(rdev);
 		if (r) {
 			dev_err(rdev->dev, "ib ring test failed (%d).\n", r);
 			if (saved) {
+				saved = false;
 				radeon_suspend(rdev);
 				goto retry;
 			}
diff --git a/drivers/gpu/drm/radeon/radeon_drv.c b/drivers/gpu/drm/radeon/radeon_drv.c
index 27d22d7..8c593ea 100644
--- a/drivers/gpu/drm/radeon/radeon_drv.c
+++ b/drivers/gpu/drm/radeon/radeon_drv.c
@@ -63,9 +63,10 @@
  *   2.19.0 - r600-eg: MSAA textures
  *   2.20.0 - r600-si: RADEON_INFO_TIMESTAMP query
  *   2.21.0 - r600-r700: FMASK and CMASK
+ *   2.22.0 - r600 only: RESOLVE_BOX allowed
  */
 #define KMS_DRIVER_MAJOR	2
-#define KMS_DRIVER_MINOR	21
+#define KMS_DRIVER_MINOR	22
 #define KMS_DRIVER_PATCHLEVEL	0
 int radeon_driver_load_kms(struct drm_device *dev, unsigned long flags);
 int radeon_driver_unload_kms(struct drm_device *dev);
diff --git a/drivers/gpu/drm/radeon/reg_srcs/r600 b/drivers/gpu/drm/radeon/reg_srcs/r600
index f93e45d..20bfbda 100644
--- a/drivers/gpu/drm/radeon/reg_srcs/r600
+++ b/drivers/gpu/drm/radeon/reg_srcs/r600
@@ -744,7 +744,6 @@
 0x00028C38 CB_CLRCMP_DST
 0x00028C3C CB_CLRCMP_MSK
 0x00028C34 CB_CLRCMP_SRC
-0x00028808 CB_COLOR_CONTROL
 0x0002842C CB_FOG_BLUE
 0x00028428 CB_FOG_GREEN
 0x00028424 CB_FOG_RED
diff --git a/drivers/hid/hid-core.c b/drivers/hid/hid-core.c
index 60ea284..8bcd168 100644
--- a/drivers/hid/hid-core.c
+++ b/drivers/hid/hid-core.c
@@ -996,7 +996,8 @@
 	struct hid_driver *hdrv = hid->driver;
 	int ret;
 
-	hid_dump_input(hid, usage, value);
+	if (!list_empty(&hid->debug_list))
+		hid_dump_input(hid, usage, value);
 
 	if (hdrv && hdrv->event && hid_match_usage(hid, usage)) {
 		ret = hdrv->event(hid, field, usage, value);
@@ -1558,7 +1559,9 @@
 	{ HID_USB_DEVICE(USB_VENDOR_ID_KYE, USB_DEVICE_ID_KYE_EASYPEN_M610X) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_LABTEC, USB_DEVICE_ID_LABTEC_WIRELESS_KEYBOARD) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_LCPOWER, USB_DEVICE_ID_LCPOWER_LC1000 ) },
- 	{ HID_USB_DEVICE(USB_VENDOR_ID_LENOVO, USB_DEVICE_ID_LENOVO_TPKBD) },
+#if IS_ENABLED(CONFIG_HID_LENOVO_TPKBD)
+	{ HID_USB_DEVICE(USB_VENDOR_ID_LENOVO, USB_DEVICE_ID_LENOVO_TPKBD) },
+#endif
 	{ HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_MX3000_RECEIVER) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_S510_RECEIVER) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_S510_RECEIVER_2) },
@@ -1624,7 +1627,6 @@
 	{ HID_USB_DEVICE(USB_VENDOR_ID_ORTEK, USB_DEVICE_ID_ORTEK_WKB2000) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_PETALYNX, USB_DEVICE_ID_PETALYNX_MAXTER_REMOTE) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_PRIMAX, USB_DEVICE_ID_PRIMAX_KEYBOARD) },
-	{ HID_USB_DEVICE(USB_VENDOR_ID_QUANTA, USB_DEVICE_ID_PIXART_IMAGING_INC_OPTICAL_TOUCH_SCREEN) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_ROCCAT, USB_DEVICE_ID_ROCCAT_KONE) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_ROCCAT, USB_DEVICE_ID_ROCCAT_ARVO) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_ROCCAT, USB_DEVICE_ID_ROCCAT_ISKU) },
diff --git a/drivers/hid/hid-logitech-dj.c b/drivers/hid/hid-logitech-dj.c
index 0f9c146..4d524b5 100644
--- a/drivers/hid/hid-logitech-dj.c
+++ b/drivers/hid/hid-logitech-dj.c
@@ -439,7 +439,7 @@
 	struct dj_report *dj_report;
 	int retval;
 
-	dj_report = kzalloc(sizeof(dj_report), GFP_KERNEL);
+	dj_report = kzalloc(sizeof(struct dj_report), GFP_KERNEL);
 	if (!dj_report)
 		return -ENOMEM;
 	dj_report->report_id = REPORT_ID_DJ_SHORT;
@@ -456,7 +456,7 @@
 	struct dj_report *dj_report;
 	int retval;
 
-	dj_report = kzalloc(sizeof(dj_report), GFP_KERNEL);
+	dj_report = kzalloc(sizeof(struct dj_report), GFP_KERNEL);
 	if (!dj_report)
 		return -ENOMEM;
 	dj_report->report_id = REPORT_ID_DJ_SHORT;
diff --git a/drivers/hid/usbhid/hid-quirks.c b/drivers/hid/usbhid/hid-quirks.c
index 903eef3..991e85c 100644
--- a/drivers/hid/usbhid/hid-quirks.c
+++ b/drivers/hid/usbhid/hid-quirks.c
@@ -70,6 +70,7 @@
 	{ USB_VENDOR_ID_CH, USB_DEVICE_ID_CH_AXIS_295, HID_QUIRK_NOGET },
 	{ USB_VENDOR_ID_DMI, USB_DEVICE_ID_DMI_ENC, HID_QUIRK_NOGET },
 	{ USB_VENDOR_ID_ELO, USB_DEVICE_ID_ELO_TS2700, HID_QUIRK_NOGET },
+	{ USB_VENDOR_ID_MGE, USB_DEVICE_ID_MGE_UPS, HID_QUIRK_NOGET },
 	{ USB_VENDOR_ID_PIXART, USB_DEVICE_ID_PIXART_OPTICAL_TOUCH_SCREEN, HID_QUIRK_NO_INIT_REPORTS },
 	{ USB_VENDOR_ID_PIXART, USB_DEVICE_ID_PIXART_OPTICAL_TOUCH_SCREEN1, HID_QUIRK_NO_INIT_REPORTS },
 	{ USB_VENDOR_ID_PIXART, USB_DEVICE_ID_PIXART_OPTICAL_TOUCH_SCREEN2, HID_QUIRK_NO_INIT_REPORTS },
diff --git a/drivers/hwmon/asus_atk0110.c b/drivers/hwmon/asus_atk0110.c
index 351d1f4..4ee5789 100644
--- a/drivers/hwmon/asus_atk0110.c
+++ b/drivers/hwmon/asus_atk0110.c
@@ -34,6 +34,12 @@
 		.matches = {
 			DMI_MATCH(DMI_BOARD_NAME, "SABERTOOTH X58")
 		}
+	}, {
+		/* Old interface reads the same sensor for fan0 and fan1 */
+		.ident = "Asus M5A78L",
+		.matches = {
+			DMI_MATCH(DMI_BOARD_NAME, "M5A78L")
+		}
 	},
 	{ }
 };
diff --git a/drivers/ide/ide-pm.c b/drivers/ide/ide-pm.c
index 9240609..8d1e32d 100644
--- a/drivers/ide/ide-pm.c
+++ b/drivers/ide/ide-pm.c
@@ -4,7 +4,7 @@
 
 int generic_ide_suspend(struct device *dev, pm_message_t mesg)
 {
-	ide_drive_t *drive = dev_get_drvdata(dev);
+	ide_drive_t *drive = to_ide_device(dev);
 	ide_drive_t *pair = ide_get_pair_dev(drive);
 	ide_hwif_t *hwif = drive->hwif;
 	struct request *rq;
@@ -40,7 +40,7 @@
 
 int generic_ide_resume(struct device *dev)
 {
-	ide_drive_t *drive = dev_get_drvdata(dev);
+	ide_drive_t *drive = to_ide_device(dev);
 	ide_drive_t *pair = ide_get_pair_dev(drive);
 	ide_hwif_t *hwif = drive->hwif;
 	struct request *rq;
diff --git a/drivers/input/keyboard/imx_keypad.c b/drivers/input/keyboard/imx_keypad.c
index ff4c0a8..ce68e36 100644
--- a/drivers/input/keyboard/imx_keypad.c
+++ b/drivers/input/keyboard/imx_keypad.c
@@ -358,6 +358,7 @@
 	/* Inhibit KDI and KRI interrupts. */
 	reg_val = readw(keypad->mmio_base + KPSR);
 	reg_val &= ~(KBD_STAT_KRIE | KBD_STAT_KDIE);
+	reg_val |= KBD_STAT_KPKR | KBD_STAT_KPKD;
 	writew(reg_val, keypad->mmio_base + KPSR);
 
 	/* Colums as open drain and disable all rows */
@@ -515,7 +516,9 @@
 	input_set_drvdata(input_dev, keypad);
 
 	/* Ensure that the keypad will stay dormant until opened */
+	clk_enable(keypad->clk);
 	imx_keypad_inhibit(keypad);
+	clk_disable(keypad->clk);
 
 	error = request_irq(irq, imx_keypad_irq_handler, 0,
 			    pdev->name, keypad);
diff --git a/drivers/input/serio/i8042-x86ia64io.h b/drivers/input/serio/i8042-x86ia64io.h
index 5ec774d..6918773 100644
--- a/drivers/input/serio/i8042-x86ia64io.h
+++ b/drivers/input/serio/i8042-x86ia64io.h
@@ -177,6 +177,20 @@
 		},
 	},
 	{
+		/* Gigabyte T1005 - defines wrong chassis type ("Other") */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "GIGABYTE"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "T1005"),
+		},
+	},
+	{
+		/* Gigabyte T1005M/P - defines wrong chassis type ("Other") */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "GIGABYTE"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "T1005M/P"),
+		},
+	},
+	{
 		.matches = {
 			DMI_MATCH(DMI_SYS_VENDOR, "Hewlett-Packard"),
 			DMI_MATCH(DMI_PRODUCT_NAME, "HP Pavilion dv9700"),
diff --git a/drivers/input/tablet/wacom_wac.c b/drivers/input/tablet/wacom_wac.c
index 0020419..532d067 100644
--- a/drivers/input/tablet/wacom_wac.c
+++ b/drivers/input/tablet/wacom_wac.c
@@ -1848,7 +1848,10 @@
 	{ "Wacom Intuos5 M", WACOM_PKGLEN_INTUOS,  44704, 27940, 2047,
 	  63, INTUOS5, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES };
 static const struct wacom_features wacom_features_0xF4 =
-	{ "Wacom Cintiq 24HD",    WACOM_PKGLEN_INTUOS,   104480, 65600, 2047,
+	{ "Wacom Cintiq 24HD",       WACOM_PKGLEN_INTUOS,   104480, 65600, 2047,
+	  63, WACOM_24HD, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES };
+static const struct wacom_features wacom_features_0xF8 =
+	{ "Wacom Cintiq 24HD touch", WACOM_PKGLEN_INTUOS,   104480, 65600, 2047,
 	  63, WACOM_24HD, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES };
 static const struct wacom_features wacom_features_0x3F =
 	{ "Wacom Cintiq 21UX",    WACOM_PKGLEN_INTUOS,    87200, 65600, 1023,
@@ -2091,6 +2094,7 @@
 	{ USB_DEVICE_WACOM(0xEF) },
 	{ USB_DEVICE_WACOM(0x47) },
 	{ USB_DEVICE_WACOM(0xF4) },
+	{ USB_DEVICE_WACOM(0xF8) },
 	{ USB_DEVICE_WACOM(0xFA) },
 	{ USB_DEVICE_LENOVO(0x6004) },
 	{ }
diff --git a/drivers/input/touchscreen/edt-ft5x06.c b/drivers/input/touchscreen/edt-ft5x06.c
index 9afc777..b06a5e3 100644
--- a/drivers/input/touchscreen/edt-ft5x06.c
+++ b/drivers/input/touchscreen/edt-ft5x06.c
@@ -602,6 +602,7 @@
 {
 	if (tsdata->debug_dir)
 		debugfs_remove_recursive(tsdata->debug_dir);
+	kfree(tsdata->raw_buffer);
 }
 
 #else
@@ -843,7 +844,6 @@
 	if (gpio_is_valid(pdata->reset_pin))
 		gpio_free(pdata->reset_pin);
 
-	kfree(tsdata->raw_buffer);
 	kfree(tsdata);
 
 	return 0;
diff --git a/drivers/isdn/capi/capi.c b/drivers/isdn/capi/capi.c
index 38c4bd8..c679867 100644
--- a/drivers/isdn/capi/capi.c
+++ b/drivers/isdn/capi/capi.c
@@ -234,7 +234,8 @@
 
 	mp->minor = minor;
 
-	dev = tty_register_device(capinc_tty_driver, minor, NULL);
+	dev = tty_port_register_device(&mp->port, capinc_tty_driver, minor,
+			NULL);
 	if (IS_ERR(dev))
 		goto err_out2;
 
diff --git a/drivers/isdn/gigaset/interface.c b/drivers/isdn/gigaset/interface.c
index a6d9fd2..67abf3f 100644
--- a/drivers/isdn/gigaset/interface.c
+++ b/drivers/isdn/gigaset/interface.c
@@ -446,8 +446,8 @@
 		goto out;
 	}
 
-	iflag = tty->termios->c_iflag;
-	cflag = tty->termios->c_cflag;
+	iflag = tty->termios.c_iflag;
+	cflag = tty->termios.c_cflag;
 	old_cflag = old ? old->c_cflag : cflag;
 	gig_dbg(DEBUG_IF, "%u: iflag %x cflag %x old %x",
 		cs->minor_index, iflag, cflag, old_cflag);
@@ -524,7 +524,8 @@
 	tasklet_init(&cs->if_wake_tasklet, if_wake, (unsigned long) cs);
 
 	mutex_lock(&cs->mutex);
-	cs->tty_dev = tty_register_device(drv->tty, cs->minor_index, NULL);
+	cs->tty_dev = tty_port_register_device(&cs->port, drv->tty,
+			cs->minor_index, NULL);
 
 	if (!IS_ERR(cs->tty_dev))
 		dev_set_drvdata(cs->tty_dev, cs);
diff --git a/drivers/isdn/i4l/isdn_tty.c b/drivers/isdn/i4l/isdn_tty.c
index 7bc5067..b817809 100644
--- a/drivers/isdn/i4l/isdn_tty.c
+++ b/drivers/isdn/i4l/isdn_tty.c
@@ -1009,15 +1009,15 @@
 		quot;
 	int i;
 
-	if (!port->tty || !port->tty->termios)
+	if (!port->tty)
 		return;
-	cflag = port->tty->termios->c_cflag;
+	cflag = port->tty->termios.c_cflag;
 
 	quot = i = cflag & CBAUD;
 	if (i & CBAUDEX) {
 		i &= ~CBAUDEX;
 		if (i < 1 || i > 2)
-			port->tty->termios->c_cflag &= ~CBAUDEX;
+			port->tty->termios.c_cflag &= ~CBAUDEX;
 		else
 			i += 15;
 	}
@@ -1097,7 +1097,7 @@
 #endif
 	isdn_unlock_drivers();
 	info->msr &= ~UART_MSR_RI;
-	if (!info->port.tty || (info->port.tty->termios->c_cflag & HUPCL)) {
+	if (!info->port.tty || (info->port.tty->termios.c_cflag & HUPCL)) {
 		info->mcr &= ~(UART_MCR_DTR | UART_MCR_RTS);
 		if (info->emu.mdmreg[REG_DTRHUP] & BIT_DTRHUP) {
 			isdn_tty_modem_reset_regs(info, 0);
@@ -1469,13 +1469,13 @@
 	if (!old_termios)
 		isdn_tty_change_speed(info);
 	else {
-		if (tty->termios->c_cflag == old_termios->c_cflag &&
-		    tty->termios->c_ispeed == old_termios->c_ispeed &&
-		    tty->termios->c_ospeed == old_termios->c_ospeed)
+		if (tty->termios.c_cflag == old_termios->c_cflag &&
+		    tty->termios.c_ispeed == old_termios->c_ispeed &&
+		    tty->termios.c_ospeed == old_termios->c_ospeed)
 			return;
 		isdn_tty_change_speed(info);
 		if ((old_termios->c_cflag & CRTSCTS) &&
-		    !(tty->termios->c_cflag & CRTSCTS))
+		    !(tty->termios.c_cflag & CRTSCTS))
 			tty->hw_stopped = 0;
 	}
 }
@@ -1486,6 +1486,18 @@
  * ------------------------------------------------------------
  */
 
+static int isdn_tty_install(struct tty_driver *driver, struct tty_struct *tty)
+{
+	modem_info *info = &dev->mdm.info[tty->index];
+
+	if (isdn_tty_paranoia_check(info, tty->name, __func__))
+		return -ENODEV;
+
+	tty->driver_data = info;
+
+	return tty_port_install(&info->port, driver, tty);
+}
+
 /*
  * This routine is called whenever a serial port is opened.  It
  * enables interrupts for a serial port, linking in its async structure into
@@ -1495,22 +1507,16 @@
 static int
 isdn_tty_open(struct tty_struct *tty, struct file *filp)
 {
-	struct tty_port *port;
-	modem_info *info;
+	modem_info *info = tty->driver_data;
+	struct tty_port *port = &info->port;
 	int retval;
 
-	info = &dev->mdm.info[tty->index];
-	if (isdn_tty_paranoia_check(info, tty->name, "isdn_tty_open"))
-		return -ENODEV;
-	port = &info->port;
 #ifdef ISDN_DEBUG_MODEM_OPEN
 	printk(KERN_DEBUG "isdn_tty_open %s, count = %d\n", tty->name,
 	       port->count);
 #endif
 	port->count++;
-	tty->driver_data = info;
 	port->tty = tty;
-	tty->port = port;
 	/*
 	 * Start up serial port
 	 */
@@ -1738,6 +1744,7 @@
 }
 
 static const struct tty_operations modem_ops = {
+	.install = isdn_tty_install,
 	.open = isdn_tty_open,
 	.close = isdn_tty_close,
 	.write = isdn_tty_write,
@@ -1782,7 +1789,7 @@
 	m->tty_modem->subtype = SERIAL_TYPE_NORMAL;
 	m->tty_modem->init_termios = tty_std_termios;
 	m->tty_modem->init_termios.c_cflag = B9600 | CS8 | CREAD | HUPCL | CLOCAL;
-	m->tty_modem->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV;
+	m->tty_modem->flags = TTY_DRIVER_REAL_RAW;
 	m->tty_modem->driver_name = "isdn_tty";
 	tty_set_operations(m->tty_modem, &modem_ops);
 	retval = tty_register_driver(m->tty_modem);
diff --git a/drivers/misc/ibmasm/uart.c b/drivers/misc/ibmasm/uart.c
index 1dcb9ae..01e2b0d 100644
--- a/drivers/misc/ibmasm/uart.c
+++ b/drivers/misc/ibmasm/uart.c
@@ -33,7 +33,7 @@
 
 void ibmasm_register_uart(struct service_processor *sp)
 {
-	struct uart_port uport;
+	struct uart_8250_port uart;
 	void __iomem *iomem_base;
 
 	iomem_base = sp->base_address + SCOUT_COM_B_BASE;
@@ -47,14 +47,14 @@
 		return;
 	}
 
-	memset(&uport, 0, sizeof(struct uart_port));
-	uport.irq	= sp->irq;
-	uport.uartclk	= 3686400;
-	uport.flags	= UPF_SHARE_IRQ;
-	uport.iotype	= UPIO_MEM;
-	uport.membase	= iomem_base;
+	memset(&uart, 0, sizeof(uart));
+	uart.port.irq		= sp->irq;
+	uart.port.uartclk	= 3686400;
+	uart.port.flags		= UPF_SHARE_IRQ;
+	uart.port.iotype	= UPIO_MEM;
+	uart.port.membase	= iomem_base;
 
-	sp->serial_line = serial8250_register_port(&uport);
+	sp->serial_line = serial8250_register_8250_port(&uart);
 	if (sp->serial_line < 0) {
 		dev_err(sp->dev, "Failed to register serial port\n");
 		return;
diff --git a/drivers/misc/pti.c b/drivers/misc/pti.c
index b7eb545..4999b34 100644
--- a/drivers/misc/pti.c
+++ b/drivers/misc/pti.c
@@ -60,7 +60,7 @@
 };
 
 struct pti_dev {
-	struct tty_port port;
+	struct tty_port port[PTITTY_MINOR_NUM];
 	unsigned long pti_addr;
 	unsigned long aperture_base;
 	void __iomem *pti_ioaddr;
@@ -76,7 +76,7 @@
  */
 static DEFINE_MUTEX(alloclock);
 
-static struct pci_device_id pci_ids[] __devinitconst = {
+static const struct pci_device_id pci_ids[] __devinitconst = {
 		{PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x82B)},
 		{0}
 };
@@ -393,25 +393,6 @@
 }
 EXPORT_SYMBOL_GPL(pti_writedata);
 
-/**
- * pti_pci_remove()- Driver exit method to remove PTI from
- *		   PCI bus.
- * @pdev: variable containing pci info of PTI.
- */
-static void __devexit pti_pci_remove(struct pci_dev *pdev)
-{
-	struct pti_dev *drv_data;
-
-	drv_data = pci_get_drvdata(pdev);
-	if (drv_data != NULL) {
-		pci_iounmap(pdev, drv_data->pti_ioaddr);
-		pci_set_drvdata(pdev, NULL);
-		kfree(drv_data);
-		pci_release_region(pdev, 1);
-		pci_disable_device(pdev);
-	}
-}
-
 /*
  * for the tty_driver_*() basic function descriptions, see tty_driver.h.
  * Specific header comments made for PTI-related specifics.
@@ -446,7 +427,7 @@
 	 * also removes a locking requirement for the actual write
 	 * procedure.
 	 */
-	return tty_port_open(&drv_data->port, tty, filp);
+	return tty_port_open(tty->port, tty, filp);
 }
 
 /**
@@ -462,7 +443,7 @@
  */
 static void pti_tty_driver_close(struct tty_struct *tty, struct file *filp)
 {
-	tty_port_close(&drv_data->port, tty, filp);
+	tty_port_close(tty->port, tty, filp);
 }
 
 /**
@@ -818,6 +799,7 @@
 static int __devinit pti_pci_probe(struct pci_dev *pdev,
 		const struct pci_device_id *ent)
 {
+	unsigned int a;
 	int retval = -EINVAL;
 	int pci_bar = 1;
 
@@ -830,7 +812,7 @@
 			__func__, __LINE__);
 		pr_err("%s(%d): Error value returned: %d\n",
 			__func__, __LINE__, retval);
-		return retval;
+		goto err;
 	}
 
 	retval = pci_enable_device(pdev);
@@ -838,17 +820,16 @@
 		dev_err(&pdev->dev,
 			"%s: pci_enable_device() returned error %d\n",
 			__func__, retval);
-		return retval;
+		goto err_unreg_misc;
 	}
 
 	drv_data = kzalloc(sizeof(*drv_data), GFP_KERNEL);
-
 	if (drv_data == NULL) {
 		retval = -ENOMEM;
 		dev_err(&pdev->dev,
 			"%s(%d): kmalloc() returned NULL memory.\n",
 			__func__, __LINE__);
-		return retval;
+		goto err_disable_pci;
 	}
 	drv_data->pti_addr = pci_resource_start(pdev, pci_bar);
 
@@ -857,33 +838,65 @@
 		dev_err(&pdev->dev,
 			"%s(%d): pci_request_region() returned error %d\n",
 			__func__, __LINE__, retval);
-		kfree(drv_data);
-		return retval;
+		goto err_free_dd;
 	}
 	drv_data->aperture_base = drv_data->pti_addr+APERTURE_14;
 	drv_data->pti_ioaddr =
 		ioremap_nocache((u32)drv_data->aperture_base,
 		APERTURE_LEN);
 	if (!drv_data->pti_ioaddr) {
-		pci_release_region(pdev, pci_bar);
 		retval = -ENOMEM;
-		kfree(drv_data);
-		return retval;
+		goto err_rel_reg;
 	}
 
 	pci_set_drvdata(pdev, drv_data);
 
-	tty_port_init(&drv_data->port);
-	drv_data->port.ops = &tty_port_ops;
+	for (a = 0; a < PTITTY_MINOR_NUM; a++) {
+		struct tty_port *port = &drv_data->port[a];
+		tty_port_init(port);
+		port->ops = &tty_port_ops;
 
-	tty_register_device(pti_tty_driver, 0, &pdev->dev);
-	tty_register_device(pti_tty_driver, 1, &pdev->dev);
+		tty_port_register_device(port, pti_tty_driver, a, &pdev->dev);
+	}
 
 	register_console(&pti_console);
 
+	return 0;
+err_rel_reg:
+	pci_release_region(pdev, pci_bar);
+err_free_dd:
+	kfree(drv_data);
+err_disable_pci:
+	pci_disable_device(pdev);
+err_unreg_misc:
+	misc_deregister(&pti_char_driver);
+err:
 	return retval;
 }
 
+/**
+ * pti_pci_remove()- Driver exit method to remove PTI from
+ *		   PCI bus.
+ * @pdev: variable containing pci info of PTI.
+ */
+static void __devexit pti_pci_remove(struct pci_dev *pdev)
+{
+	struct pti_dev *drv_data = pci_get_drvdata(pdev);
+
+	unregister_console(&pti_console);
+
+	tty_unregister_device(pti_tty_driver, 0);
+	tty_unregister_device(pti_tty_driver, 1);
+
+	iounmap(drv_data->pti_ioaddr);
+	pci_set_drvdata(pdev, NULL);
+	kfree(drv_data);
+	pci_release_region(pdev, 1);
+	pci_disable_device(pdev);
+
+	misc_deregister(&pti_char_driver);
+}
+
 static struct pci_driver pti_pci_driver = {
 	.name		= PCINAME,
 	.id_table	= pci_ids,
@@ -933,25 +946,24 @@
 		pr_err("%s(%d): Error value returned: %d\n",
 			__func__, __LINE__, retval);
 
-		pti_tty_driver = NULL;
-		return retval;
+		goto put_tty;
 	}
 
 	retval = pci_register_driver(&pti_pci_driver);
-
 	if (retval) {
 		pr_err("%s(%d): PCI registration failed of pti driver\n",
 			__func__, __LINE__);
 		pr_err("%s(%d): Error value returned: %d\n",
 			__func__, __LINE__, retval);
-
-		tty_unregister_driver(pti_tty_driver);
-		pr_err("%s(%d): Unregistering TTY part of pti driver\n",
-			__func__, __LINE__);
-		pti_tty_driver = NULL;
-		return retval;
+		goto unreg_tty;
 	}
 
+	return 0;
+unreg_tty:
+	tty_unregister_driver(pti_tty_driver);
+put_tty:
+	put_tty_driver(pti_tty_driver);
+	pti_tty_driver = NULL;
 	return retval;
 }
 
@@ -960,31 +972,9 @@
  */
 static void __exit pti_exit(void)
 {
-	int retval;
-
-	tty_unregister_device(pti_tty_driver, 0);
-	tty_unregister_device(pti_tty_driver, 1);
-
-	retval = tty_unregister_driver(pti_tty_driver);
-	if (retval) {
-		pr_err("%s(%d): TTY unregistration failed of pti driver\n",
-			__func__, __LINE__);
-		pr_err("%s(%d): Error value returned: %d\n",
-			__func__, __LINE__, retval);
-	}
-
+	tty_unregister_driver(pti_tty_driver);
 	pci_unregister_driver(&pti_pci_driver);
-
-	retval = misc_deregister(&pti_char_driver);
-	if (retval) {
-		pr_err("%s(%d): CHAR unregistration failed of pti driver\n",
-			__func__, __LINE__);
-		pr_err("%s(%d): Error value returned: %d\n",
-			__func__, __LINE__, retval);
-	}
-
-	unregister_console(&pti_console);
-	return;
+	put_tty_driver(pti_tty_driver);
 }
 
 module_init(pti_init);
diff --git a/drivers/mmc/card/block.c b/drivers/mmc/card/block.c
index f1c84de..172a768 100644
--- a/drivers/mmc/card/block.c
+++ b/drivers/mmc/card/block.c
@@ -1411,7 +1411,8 @@
 		/* complete ongoing async transfer before issuing discard */
 		if (card->host->areq)
 			mmc_blk_issue_rw_rq(mq, NULL);
-		if (req->cmd_flags & REQ_SECURE)
+		if (req->cmd_flags & REQ_SECURE &&
+			!(card->quirks & MMC_QUIRK_SEC_ERASE_TRIM_BROKEN))
 			ret = mmc_blk_issue_secdiscard_rq(mq, req);
 		else
 			ret = mmc_blk_issue_discard_rq(mq, req);
@@ -1716,6 +1717,7 @@
 #define CID_MANFID_SANDISK	0x2
 #define CID_MANFID_TOSHIBA	0x11
 #define CID_MANFID_MICRON	0x13
+#define CID_MANFID_SAMSUNG	0x15
 
 static const struct mmc_fixup blk_fixups[] =
 {
@@ -1752,6 +1754,28 @@
 	MMC_FIXUP(CID_NAME_ANY, CID_MANFID_MICRON, 0x200, add_quirk_mmc,
 		  MMC_QUIRK_LONG_READ_TIME),
 
+	/*
+	 * On these Samsung MoviNAND parts, performing secure erase or
+	 * secure trim can result in unrecoverable corruption due to a
+	 * firmware bug.
+	 */
+	MMC_FIXUP("M8G2FA", CID_MANFID_SAMSUNG, CID_OEMID_ANY, add_quirk_mmc,
+		  MMC_QUIRK_SEC_ERASE_TRIM_BROKEN),
+	MMC_FIXUP("MAG4FA", CID_MANFID_SAMSUNG, CID_OEMID_ANY, add_quirk_mmc,
+		  MMC_QUIRK_SEC_ERASE_TRIM_BROKEN),
+	MMC_FIXUP("MBG8FA", CID_MANFID_SAMSUNG, CID_OEMID_ANY, add_quirk_mmc,
+		  MMC_QUIRK_SEC_ERASE_TRIM_BROKEN),
+	MMC_FIXUP("MCGAFA", CID_MANFID_SAMSUNG, CID_OEMID_ANY, add_quirk_mmc,
+		  MMC_QUIRK_SEC_ERASE_TRIM_BROKEN),
+	MMC_FIXUP("VAL00M", CID_MANFID_SAMSUNG, CID_OEMID_ANY, add_quirk_mmc,
+		  MMC_QUIRK_SEC_ERASE_TRIM_BROKEN),
+	MMC_FIXUP("VYL00M", CID_MANFID_SAMSUNG, CID_OEMID_ANY, add_quirk_mmc,
+		  MMC_QUIRK_SEC_ERASE_TRIM_BROKEN),
+	MMC_FIXUP("KYL00M", CID_MANFID_SAMSUNG, CID_OEMID_ANY, add_quirk_mmc,
+		  MMC_QUIRK_SEC_ERASE_TRIM_BROKEN),
+	MMC_FIXUP("VZL00M", CID_MANFID_SAMSUNG, CID_OEMID_ANY, add_quirk_mmc,
+		  MMC_QUIRK_SEC_ERASE_TRIM_BROKEN),
+
 	END_FIXUP
 };
 
diff --git a/drivers/mmc/card/sdio_uart.c b/drivers/mmc/card/sdio_uart.c
index 5a2cbfa..d2339ea 100644
--- a/drivers/mmc/card/sdio_uart.c
+++ b/drivers/mmc/card/sdio_uart.c
@@ -518,7 +518,7 @@
 	if (status & UART_MSR_DCTS) {
 		port->icount.cts++;
 		tty = tty_port_tty_get(&port->port);
-		if (tty && (tty->termios->c_cflag & CRTSCTS)) {
+		if (tty && (tty->termios.c_cflag & CRTSCTS)) {
 			int cts = (status & UART_MSR_CTS);
 			if (tty->hw_stopped) {
 				if (cts) {
@@ -671,12 +671,12 @@
 	port->ier = UART_IER_RLSI|UART_IER_RDI|UART_IER_RTOIE|UART_IER_UUE;
 	port->mctrl = TIOCM_OUT2;
 
-	sdio_uart_change_speed(port, tty->termios, NULL);
+	sdio_uart_change_speed(port, &tty->termios, NULL);
 
-	if (tty->termios->c_cflag & CBAUD)
+	if (tty->termios.c_cflag & CBAUD)
 		sdio_uart_set_mctrl(port, TIOCM_RTS | TIOCM_DTR);
 
-	if (tty->termios->c_cflag & CRTSCTS)
+	if (tty->termios.c_cflag & CRTSCTS)
 		if (!(sdio_uart_get_mctrl(port) & TIOCM_CTS))
 			tty->hw_stopped = 1;
 
@@ -850,7 +850,7 @@
 {
 	struct sdio_uart_port *port = tty->driver_data;
 
-	if (!I_IXOFF(tty) && !(tty->termios->c_cflag & CRTSCTS))
+	if (!I_IXOFF(tty) && !(tty->termios.c_cflag & CRTSCTS))
 		return;
 
 	if (sdio_uart_claim_func(port) != 0)
@@ -861,7 +861,7 @@
 		sdio_uart_start_tx(port);
 	}
 
-	if (tty->termios->c_cflag & CRTSCTS)
+	if (tty->termios.c_cflag & CRTSCTS)
 		sdio_uart_clear_mctrl(port, TIOCM_RTS);
 
 	sdio_uart_irq(port->func);
@@ -872,7 +872,7 @@
 {
 	struct sdio_uart_port *port = tty->driver_data;
 
-	if (!I_IXOFF(tty) && !(tty->termios->c_cflag & CRTSCTS))
+	if (!I_IXOFF(tty) && !(tty->termios.c_cflag & CRTSCTS))
 		return;
 
 	if (sdio_uart_claim_func(port) != 0)
@@ -887,7 +887,7 @@
 		}
 	}
 
-	if (tty->termios->c_cflag & CRTSCTS)
+	if (tty->termios.c_cflag & CRTSCTS)
 		sdio_uart_set_mctrl(port, TIOCM_RTS);
 
 	sdio_uart_irq(port->func);
@@ -898,12 +898,12 @@
 						struct ktermios *old_termios)
 {
 	struct sdio_uart_port *port = tty->driver_data;
-	unsigned int cflag = tty->termios->c_cflag;
+	unsigned int cflag = tty->termios.c_cflag;
 
 	if (sdio_uart_claim_func(port) != 0)
 		return;
 
-	sdio_uart_change_speed(port, tty->termios, old_termios);
+	sdio_uart_change_speed(port, &tty->termios, old_termios);
 
 	/* Handle transition to B0 status */
 	if ((old_termios->c_cflag & CBAUD) && !(cflag & CBAUD))
@@ -1132,8 +1132,8 @@
 		kfree(port);
 	} else {
 		struct device *dev;
-		dev = tty_register_device(sdio_uart_tty_driver,
-						port->index, &func->dev);
+		dev = tty_port_register_device(&port->port,
+				sdio_uart_tty_driver, port->index, &func->dev);
 		if (IS_ERR(dev)) {
 			sdio_uart_port_remove(port);
 			ret = PTR_ERR(dev);
diff --git a/drivers/mmc/host/atmel-mci.c b/drivers/mmc/host/atmel-mci.c
index 322412c..a53c7c4 100644
--- a/drivers/mmc/host/atmel-mci.c
+++ b/drivers/mmc/host/atmel-mci.c
@@ -81,6 +81,7 @@
 	bool	has_bad_data_ordering;
 	bool	need_reset_after_xfer;
 	bool	need_blksz_mul_4;
+	bool	need_notbusy_for_read_ops;
 };
 
 struct atmel_mci_dma {
@@ -1625,7 +1626,8 @@
 				__func__);
 			atmci_set_completed(host, EVENT_XFER_COMPLETE);
 
-			if (host->data->flags & MMC_DATA_WRITE) {
+			if (host->caps.need_notbusy_for_read_ops ||
+			   (host->data->flags & MMC_DATA_WRITE)) {
 				atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
 				state = STATE_WAITING_NOTBUSY;
 			} else if (host->mrq->stop) {
@@ -2218,6 +2220,7 @@
 	host->caps.has_bad_data_ordering = 1;
 	host->caps.need_reset_after_xfer = 1;
 	host->caps.need_blksz_mul_4 = 1;
+	host->caps.need_notbusy_for_read_ops = 0;
 
 	/* keep only major version number */
 	switch (version & 0xf00) {
@@ -2238,6 +2241,7 @@
 	case 0x200:
 		host->caps.has_rwproof = 1;
 		host->caps.need_blksz_mul_4 = 0;
+		host->caps.need_notbusy_for_read_ops = 1;
 	case 0x100:
 		host->caps.has_bad_data_ordering = 0;
 		host->caps.need_reset_after_xfer = 0;
diff --git a/drivers/mmc/host/bfin_sdh.c b/drivers/mmc/host/bfin_sdh.c
index 0366617..a17dd73 100644
--- a/drivers/mmc/host/bfin_sdh.c
+++ b/drivers/mmc/host/bfin_sdh.c
@@ -49,13 +49,6 @@
 #define bfin_write_SDH_CFG		bfin_write_RSI_CFG
 #endif
 
-struct dma_desc_array {
-	unsigned long	start_addr;
-	unsigned short	cfg;
-	unsigned short	x_count;
-	short		x_modify;
-} __packed;
-
 struct sdh_host {
 	struct mmc_host		*mmc;
 	spinlock_t		lock;
diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
index 72dc3cd..af40d22 100644
--- a/drivers/mmc/host/dw_mmc.c
+++ b/drivers/mmc/host/dw_mmc.c
@@ -627,6 +627,7 @@
 {
 	struct dw_mci *host = slot->host;
 	u32 div;
+	u32 clk_en_a;
 
 	if (slot->clock != host->current_speed) {
 		div = host->bus_hz / slot->clock;
@@ -659,9 +660,11 @@
 		mci_send_cmd(slot,
 			     SDMMC_CMD_UPD_CLK | SDMMC_CMD_PRV_DAT_WAIT, 0);
 
-		/* enable clock */
-		mci_writel(host, CLKENA, ((SDMMC_CLKEN_ENABLE |
-			   SDMMC_CLKEN_LOW_PWR) << slot->id));
+		/* enable clock; only low power if no SDIO */
+		clk_en_a = SDMMC_CLKEN_ENABLE << slot->id;
+		if (!(mci_readl(host, INTMASK) & SDMMC_INT_SDIO(slot->id)))
+			clk_en_a |= SDMMC_CLKEN_LOW_PWR << slot->id;
+		mci_writel(host, CLKENA, clk_en_a);
 
 		/* inform CIU */
 		mci_send_cmd(slot,
@@ -862,6 +865,30 @@
 	return present;
 }
 
+/*
+ * Disable lower power mode.
+ *
+ * Low power mode will stop the card clock when idle.  According to the
+ * description of the CLKENA register we should disable low power mode
+ * for SDIO cards if we need SDIO interrupts to work.
+ *
+ * This function is fast if low power mode is already disabled.
+ */
+static void dw_mci_disable_low_power(struct dw_mci_slot *slot)
+{
+	struct dw_mci *host = slot->host;
+	u32 clk_en_a;
+	const u32 clken_low_pwr = SDMMC_CLKEN_LOW_PWR << slot->id;
+
+	clk_en_a = mci_readl(host, CLKENA);
+
+	if (clk_en_a & clken_low_pwr) {
+		mci_writel(host, CLKENA, clk_en_a & ~clken_low_pwr);
+		mci_send_cmd(slot, SDMMC_CMD_UPD_CLK |
+			     SDMMC_CMD_PRV_DAT_WAIT, 0);
+	}
+}
+
 static void dw_mci_enable_sdio_irq(struct mmc_host *mmc, int enb)
 {
 	struct dw_mci_slot *slot = mmc_priv(mmc);
@@ -871,6 +898,14 @@
 	/* Enable/disable Slot Specific SDIO interrupt */
 	int_mask = mci_readl(host, INTMASK);
 	if (enb) {
+		/*
+		 * Turn off low power mode if it was enabled.  This is a bit of
+		 * a heavy operation and we disable / enable IRQs a lot, so
+		 * we'll leave low power mode disabled and it will get
+		 * re-enabled again in dw_mci_setup_bus().
+		 */
+		dw_mci_disable_low_power(slot);
+
 		mci_writel(host, INTMASK,
 			   (int_mask | SDMMC_INT_SDIO(slot->id)));
 	} else {
@@ -1429,22 +1464,10 @@
 			nbytes += len;
 			remain -= len;
 		} while (remain);
-		sg_miter->consumed = offset;
 
+		sg_miter->consumed = offset;
 		status = mci_readl(host, MINTSTS);
 		mci_writel(host, RINTSTS, SDMMC_INT_RXDR);
-		if (status & DW_MCI_DATA_ERROR_FLAGS) {
-			host->data_status = status;
-			data->bytes_xfered += nbytes;
-			sg_miter_stop(sg_miter);
-			host->sg = NULL;
-			smp_wmb();
-
-			set_bit(EVENT_DATA_ERROR, &host->pending_events);
-
-			tasklet_schedule(&host->tasklet);
-			return;
-		}
 	} while (status & SDMMC_INT_RXDR); /*if the RXDR is ready read again*/
 	data->bytes_xfered += nbytes;
 
@@ -1497,23 +1520,10 @@
 			nbytes += len;
 			remain -= len;
 		} while (remain);
-		sg_miter->consumed = offset;
 
+		sg_miter->consumed = offset;
 		status = mci_readl(host, MINTSTS);
 		mci_writel(host, RINTSTS, SDMMC_INT_TXDR);
-		if (status & DW_MCI_DATA_ERROR_FLAGS) {
-			host->data_status = status;
-			data->bytes_xfered += nbytes;
-			sg_miter_stop(sg_miter);
-			host->sg = NULL;
-
-			smp_wmb();
-
-			set_bit(EVENT_DATA_ERROR, &host->pending_events);
-
-			tasklet_schedule(&host->tasklet);
-			return;
-		}
 	} while (status & SDMMC_INT_TXDR); /* if TXDR write again */
 	data->bytes_xfered += nbytes;
 
@@ -1547,12 +1557,11 @@
 static irqreturn_t dw_mci_interrupt(int irq, void *dev_id)
 {
 	struct dw_mci *host = dev_id;
-	u32 status, pending;
+	u32 pending;
 	unsigned int pass_count = 0;
 	int i;
 
 	do {
-		status = mci_readl(host, RINTSTS);
 		pending = mci_readl(host, MINTSTS); /* read-only mask reg */
 
 		/*
@@ -1570,7 +1579,7 @@
 
 		if (pending & DW_MCI_CMD_ERROR_FLAGS) {
 			mci_writel(host, RINTSTS, DW_MCI_CMD_ERROR_FLAGS);
-			host->cmd_status = status;
+			host->cmd_status = pending;
 			smp_wmb();
 			set_bit(EVENT_CMD_COMPLETE, &host->pending_events);
 		}
@@ -1578,18 +1587,16 @@
 		if (pending & DW_MCI_DATA_ERROR_FLAGS) {
 			/* if there is an error report DATA_ERROR */
 			mci_writel(host, RINTSTS, DW_MCI_DATA_ERROR_FLAGS);
-			host->data_status = status;
+			host->data_status = pending;
 			smp_wmb();
 			set_bit(EVENT_DATA_ERROR, &host->pending_events);
-			if (!(pending & (SDMMC_INT_DTO | SDMMC_INT_DCRC |
-					 SDMMC_INT_SBE | SDMMC_INT_EBE)))
-				tasklet_schedule(&host->tasklet);
+			tasklet_schedule(&host->tasklet);
 		}
 
 		if (pending & SDMMC_INT_DATA_OVER) {
 			mci_writel(host, RINTSTS, SDMMC_INT_DATA_OVER);
 			if (!host->data_status)
-				host->data_status = status;
+				host->data_status = pending;
 			smp_wmb();
 			if (host->dir_status == DW_MCI_RECV_STATUS) {
 				if (host->sg != NULL)
@@ -1613,7 +1620,7 @@
 
 		if (pending & SDMMC_INT_CMD_DONE) {
 			mci_writel(host, RINTSTS, SDMMC_INT_CMD_DONE);
-			dw_mci_cmd_interrupt(host, status);
+			dw_mci_cmd_interrupt(host, pending);
 		}
 
 		if (pending & SDMMC_INT_CD) {
diff --git a/drivers/mmc/host/mxs-mmc.c b/drivers/mmc/host/mxs-mmc.c
index a51f930..ad3fcea 100644
--- a/drivers/mmc/host/mxs-mmc.c
+++ b/drivers/mmc/host/mxs-mmc.c
@@ -285,11 +285,11 @@
 	writel(stat & MXS_MMC_IRQ_BITS,
 	       host->base + HW_SSP_CTRL1(host) + STMP_OFFSET_REG_CLR);
 
+	spin_unlock(&host->lock);
+
 	if ((stat & BM_SSP_CTRL1_SDIO_IRQ) && (stat & BM_SSP_CTRL1_SDIO_IRQ_EN))
 		mmc_signal_sdio_irq(host->mmc);
 
-	spin_unlock(&host->lock);
-
 	if (stat & BM_SSP_CTRL1_RESP_TIMEOUT_IRQ)
 		cmd->error = -ETIMEDOUT;
 	else if (stat & BM_SSP_CTRL1_RESP_ERR_IRQ)
@@ -644,11 +644,6 @@
 		       host->base + HW_SSP_CTRL0 + STMP_OFFSET_REG_SET);
 		writel(BM_SSP_CTRL1_SDIO_IRQ_EN,
 		       host->base + HW_SSP_CTRL1(host) + STMP_OFFSET_REG_SET);
-
-		if (readl(host->base + HW_SSP_STATUS(host)) &
-				BM_SSP_STATUS_SDIO_IRQ)
-			mmc_signal_sdio_irq(host->mmc);
-
 	} else {
 		writel(BM_SSP_CTRL0_SDIO_IRQ_CHECK,
 		       host->base + HW_SSP_CTRL0 + STMP_OFFSET_REG_CLR);
@@ -657,6 +652,11 @@
 	}
 
 	spin_unlock_irqrestore(&host->lock, flags);
+
+	if (enable && readl(host->base + HW_SSP_STATUS(host)) &
+			BM_SSP_STATUS_SDIO_IRQ)
+		mmc_signal_sdio_irq(host->mmc);
+
 }
 
 static const struct mmc_host_ops mxs_mmc_ops = {
diff --git a/drivers/mmc/host/omap.c b/drivers/mmc/host/omap.c
index 50e08f0..87c0293 100644
--- a/drivers/mmc/host/omap.c
+++ b/drivers/mmc/host/omap.c
@@ -33,7 +33,6 @@
 #include <asm/io.h>
 #include <asm/irq.h>
 
-#include <plat/board.h>
 #include <plat/mmc.h>
 #include <asm/gpio.h>
 #include <plat/dma.h>
@@ -668,7 +667,7 @@
 static void
 mmc_omap_xfer_data(struct mmc_omap_host *host, int write)
 {
-	int n;
+	int n, nwords;
 
 	if (host->buffer_bytes_left == 0) {
 		host->sg_idx++;
@@ -678,15 +677,23 @@
 	n = 64;
 	if (n > host->buffer_bytes_left)
 		n = host->buffer_bytes_left;
+
+	nwords = n / 2;
+	nwords += n & 1; /* handle odd number of bytes to transfer */
+
 	host->buffer_bytes_left -= n;
 	host->total_bytes_left -= n;
 	host->data->bytes_xfered += n;
 
 	if (write) {
-		__raw_writesw(host->virt_base + OMAP_MMC_REG(host, DATA), host->buffer, n);
+		__raw_writesw(host->virt_base + OMAP_MMC_REG(host, DATA),
+			      host->buffer, nwords);
 	} else {
-		__raw_readsw(host->virt_base + OMAP_MMC_REG(host, DATA), host->buffer, n);
+		__raw_readsw(host->virt_base + OMAP_MMC_REG(host, DATA),
+			     host->buffer, nwords);
 	}
+
+	host->buffer += nwords;
 }
 
 static inline void mmc_omap_report_irq(u16 status)
diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c
index 3a09f93..f871b31 100644
--- a/drivers/mmc/host/omap_hsmmc.c
+++ b/drivers/mmc/host/omap_hsmmc.c
@@ -40,7 +40,6 @@
 #include <linux/regulator/consumer.h>
 #include <linux/pm_runtime.h>
 #include <mach/hardware.h>
-#include <plat/board.h>
 #include <plat/mmc.h>
 #include <plat/cpu.h>
 
diff --git a/drivers/mmc/host/sdhci-esdhc.h b/drivers/mmc/host/sdhci-esdhc.h
index b97b2f5..d25f9ab 100644
--- a/drivers/mmc/host/sdhci-esdhc.h
+++ b/drivers/mmc/host/sdhci-esdhc.h
@@ -48,14 +48,14 @@
 	int div = 1;
 	u32 temp;
 
+	if (clock == 0)
+		goto out;
+
 	temp = sdhci_readl(host, ESDHC_SYSTEM_CONTROL);
 	temp &= ~(ESDHC_CLOCK_IPGEN | ESDHC_CLOCK_HCKEN | ESDHC_CLOCK_PEREN
 		| ESDHC_CLOCK_MASK);
 	sdhci_writel(host, temp, ESDHC_SYSTEM_CONTROL);
 
-	if (clock == 0)
-		goto out;
-
 	while (host->max_clk / pre_div / 16 > clock && pre_div < 256)
 		pre_div *= 2;
 
diff --git a/drivers/mtd/onenand/omap2.c b/drivers/mtd/onenand/omap2.c
index 3ff893d..108ab1a 100644
--- a/drivers/mtd/onenand/omap2.c
+++ b/drivers/mtd/onenand/omap2.c
@@ -44,8 +44,6 @@
 
 #include <plat/dma.h>
 
-#include <plat/board.h>
-
 #define DRIVER_NAME "omap2-onenand"
 
 #define ONENAND_BUFRAM_SIZE	(1024 * 5)
diff --git a/drivers/mtd/ubi/vtbl.c b/drivers/mtd/ubi/vtbl.c
index 437bc19..568307c 100644
--- a/drivers/mtd/ubi/vtbl.c
+++ b/drivers/mtd/ubi/vtbl.c
@@ -340,7 +340,7 @@
 	 * of this LEB as it will be deleted and freed in 'ubi_add_to_av()'.
 	 */
 	err = ubi_add_to_av(ubi, ai, new_aeb->pnum, new_aeb->ec, vid_hdr, 0);
-	kfree(new_aeb);
+	kmem_cache_free(ai->aeb_slab_cache, new_aeb);
 	ubi_free_vid_hdr(ubi, vid_hdr);
 	return err;
 
@@ -353,7 +353,7 @@
 		list_add(&new_aeb->u.list, &ai->erase);
 		goto retry;
 	}
-	kfree(new_aeb);
+	kmem_cache_free(ai->aeb_slab_cache, new_aeb);
 out_free:
 	ubi_free_vid_hdr(ubi, vid_hdr);
 	return err;
diff --git a/drivers/net/can/sja1000/sja1000_platform.c b/drivers/net/can/sja1000/sja1000_platform.c
index 4f50145..662c5f7 100644
--- a/drivers/net/can/sja1000/sja1000_platform.c
+++ b/drivers/net/can/sja1000/sja1000_platform.c
@@ -109,7 +109,9 @@
 	priv = netdev_priv(dev);
 
 	dev->irq = res_irq->start;
-	priv->irq_flags = res_irq->flags & (IRQF_TRIGGER_MASK | IRQF_SHARED);
+	priv->irq_flags = res_irq->flags & IRQF_TRIGGER_MASK;
+	if (res_irq->flags & IORESOURCE_IRQ_SHAREABLE)
+		priv->irq_flags |= IRQF_SHARED;
 	priv->reg_base = addr;
 	/* The CAN clock frequency is half the oscillator clock frequency */
 	priv->can.clock.freq = pdata->osc_freq / 2;
diff --git a/drivers/net/can/softing/softing_fw.c b/drivers/net/can/softing/softing_fw.c
index 3105961..b595d34 100644
--- a/drivers/net/can/softing/softing_fw.c
+++ b/drivers/net/can/softing/softing_fw.c
@@ -150,7 +150,7 @@
 	const uint8_t *mem, *end, *dat;
 	uint16_t type, len;
 	uint32_t addr;
-	uint8_t *buf = NULL;
+	uint8_t *buf = NULL, *new_buf;
 	int buflen = 0;
 	int8_t type_end = 0;
 
@@ -199,11 +199,12 @@
 		if (len > buflen) {
 			/* align buflen */
 			buflen = (len + (1024-1)) & ~(1024-1);
-			buf = krealloc(buf, buflen, GFP_KERNEL);
-			if (!buf) {
+			new_buf = krealloc(buf, buflen, GFP_KERNEL);
+			if (!new_buf) {
 				ret = -ENOMEM;
 				goto failed;
 			}
+			buf = new_buf;
 		}
 		/* verify record data */
 		memcpy_fromio(buf, &dpram[addr + offset], len);
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h
index 463b9ec..6d1a24a 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h
@@ -1708,9 +1708,6 @@
 			continue;		\
 		else
 
-#define for_each_napi_rx_queue(bp, var) \
-	for ((var) = 0; (var) < bp->num_napi_queues; (var)++)
-
 /* Skip OOO FP */
 #define for_each_tx_queue(bp, var) \
 	for ((var) = 0; (var) < BNX2X_NUM_QUEUES(bp); (var)++) \
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
index e879e19..af20c6e 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
@@ -2046,6 +2046,8 @@
 	 */
 	bnx2x_setup_tc(bp->dev, bp->max_cos);
 
+	/* Add all NAPI objects */
+	bnx2x_add_all_napi(bp);
 	bnx2x_napi_enable(bp);
 
 	/* set pf load just before approaching the MCP */
@@ -2408,6 +2410,8 @@
 
 		/* Disable HW interrupts, NAPI */
 		bnx2x_netif_stop(bp, 1);
+		/* Delete all NAPI objects */
+		bnx2x_del_all_napi(bp);
 
 		/* Release IRQs */
 		bnx2x_free_irq(bp);
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h
index dfa757e..21b5532 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h
@@ -792,7 +792,7 @@
 	bp->num_napi_queues = bp->num_queues;
 
 	/* Add NAPI objects */
-	for_each_napi_rx_queue(bp, i)
+	for_each_rx_queue(bp, i)
 		netif_napi_add(bp->dev, &bnx2x_fp(bp, i, napi),
 			       bnx2x_poll, BNX2X_NAPI_WEIGHT);
 }
@@ -801,7 +801,7 @@
 {
 	int i;
 
-	for_each_napi_rx_queue(bp, i)
+	for_each_rx_queue(bp, i)
 		netif_napi_del(&bnx2x_fp(bp, i, napi));
 }
 
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c
index fc4e0e3..c37a68d 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c
@@ -2888,11 +2888,9 @@
  */
 static void bnx2x_change_num_queues(struct bnx2x *bp, int num_rss)
 {
-	bnx2x_del_all_napi(bp);
 	bnx2x_disable_msi(bp);
 	BNX2X_NUM_QUEUES(bp) = num_rss + NON_ETH_CONTEXT_USE;
 	bnx2x_set_int_mode(bp);
-	bnx2x_add_all_napi(bp);
 }
 
 /**
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
index 02b5a34..2105498 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
@@ -8427,6 +8427,8 @@
 
 	/* Disable HW interrupts, NAPI */
 	bnx2x_netif_stop(bp, 1);
+	/* Delete all NAPI objects */
+	bnx2x_del_all_napi(bp);
 
 	/* Release IRQs */
 	bnx2x_free_irq(bp);
@@ -11229,10 +11231,12 @@
 static void poll_bnx2x(struct net_device *dev)
 {
 	struct bnx2x *bp = netdev_priv(dev);
+	int i;
 
-	disable_irq(bp->pdev->irq);
-	bnx2x_interrupt(bp->pdev->irq, dev);
-	enable_irq(bp->pdev->irq);
+	for_each_eth_queue(bp, i) {
+		struct bnx2x_fastpath *fp = &bp->fp[i];
+		napi_schedule(&bnx2x_fp(bp, fp->index, napi));
+	}
 }
 #endif
 
@@ -11899,9 +11903,6 @@
 	 */
 	bnx2x_set_int_mode(bp);
 
-	/* Add all NAPI objects */
-	bnx2x_add_all_napi(bp);
-
 	rc = register_netdev(dev);
 	if (rc) {
 		dev_err(&pdev->dev, "Cannot register net device\n");
@@ -11976,9 +11977,6 @@
 
 	unregister_netdev(dev);
 
-	/* Delete all NAPI objects */
-	bnx2x_del_all_napi(bp);
-
 	/* Power on: we can't let PCI layer write to us while we are in D3 */
 	bnx2x_set_power_state(bp, PCI_D0);
 
@@ -12025,6 +12023,8 @@
 	bnx2x_tx_disable(bp);
 
 	bnx2x_netif_stop(bp, 0);
+	/* Delete all NAPI objects */
+	bnx2x_del_all_napi(bp);
 
 	del_timer_sync(&bp->timer);
 
diff --git a/drivers/net/ethernet/cirrus/cs89x0.c b/drivers/net/ethernet/cirrus/cs89x0.c
index 845b202..1384469 100644
--- a/drivers/net/ethernet/cirrus/cs89x0.c
+++ b/drivers/net/ethernet/cirrus/cs89x0.c
@@ -1243,6 +1243,7 @@
 {
 	struct net_local *lp = netdev_priv(dev);
 	unsigned long flags;
+	u16 cfg;
 
 	spin_lock_irqsave(&lp->lock, flags);
 	if (dev->flags & IFF_PROMISC)
@@ -1260,11 +1261,10 @@
 	/* in promiscuous mode, we accept errored packets,
 	 * so we have to enable interrupts on them also
 	 */
-	writereg(dev, PP_RxCFG,
-		 (lp->curr_rx_cfg |
-		  (lp->rx_mode == RX_ALL_ACCEPT)
-		  ? (RX_CRC_ERROR_ENBL | RX_RUNT_ENBL | RX_EXTRA_DATA_ENBL)
-		  : 0));
+	cfg = lp->curr_rx_cfg;
+	if (lp->rx_mode == RX_ALL_ACCEPT)
+		cfg |= RX_CRC_ERROR_ENBL | RX_RUNT_ENBL | RX_EXTRA_DATA_ENBL;
+	writereg(dev, PP_RxCFG, cfg);
 	spin_unlock_irqrestore(&lp->lock, flags);
 }
 
diff --git a/drivers/net/ethernet/emulex/benet/be_cmds.c b/drivers/net/ethernet/emulex/benet/be_cmds.c
index 7fac97b..8c63d06 100644
--- a/drivers/net/ethernet/emulex/benet/be_cmds.c
+++ b/drivers/net/ethernet/emulex/benet/be_cmds.c
@@ -259,7 +259,7 @@
 	int num = 0, status = 0;
 	struct be_mcc_obj *mcc_obj = &adapter->mcc_obj;
 
-	spin_lock_bh(&adapter->mcc_cq_lock);
+	spin_lock(&adapter->mcc_cq_lock);
 	while ((compl = be_mcc_compl_get(adapter))) {
 		if (compl->flags & CQE_FLAGS_ASYNC_MASK) {
 			/* Interpret flags as an async trailer */
@@ -280,7 +280,7 @@
 	if (num)
 		be_cq_notify(adapter, mcc_obj->cq.id, mcc_obj->rearm_cq, num);
 
-	spin_unlock_bh(&adapter->mcc_cq_lock);
+	spin_unlock(&adapter->mcc_cq_lock);
 	return status;
 }
 
@@ -295,7 +295,9 @@
 		if (be_error(adapter))
 			return -EIO;
 
+		local_bh_disable();
 		status = be_process_mcc(adapter);
+		local_bh_enable();
 
 		if (atomic_read(&mcc_obj->q.used) == 0)
 			break;
diff --git a/drivers/net/ethernet/emulex/benet/be_main.c b/drivers/net/ethernet/emulex/benet/be_main.c
index 90a903d8..78b8aa8 100644
--- a/drivers/net/ethernet/emulex/benet/be_main.c
+++ b/drivers/net/ethernet/emulex/benet/be_main.c
@@ -3763,7 +3763,9 @@
 	/* when interrupts are not yet enabled, just reap any pending
 	* mcc completions */
 	if (!netif_running(adapter->netdev)) {
+		local_bh_disable();
 		be_process_mcc(adapter);
+		local_bh_enable();
 		goto reschedule;
 	}
 
diff --git a/drivers/net/ethernet/freescale/gianfar.c b/drivers/net/ethernet/freescale/gianfar.c
index 4605f72..d3233f5 100644
--- a/drivers/net/ethernet/freescale/gianfar.c
+++ b/drivers/net/ethernet/freescale/gianfar.c
@@ -1041,7 +1041,7 @@
 
 	if (priv->device_flags & FSL_GIANFAR_DEV_HAS_VLAN) {
 		dev->hw_features |= NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX;
-		dev->features |= NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX;
+		dev->features |= NETIF_F_HW_VLAN_RX;
 	}
 
 	if (priv->device_flags & FSL_GIANFAR_DEV_HAS_EXTENDED_HASH) {
diff --git a/drivers/net/ethernet/intel/e1000e/e1000.h b/drivers/net/ethernet/intel/e1000e/e1000.h
index cd15332..cb3356c 100644
--- a/drivers/net/ethernet/intel/e1000e/e1000.h
+++ b/drivers/net/ethernet/intel/e1000e/e1000.h
@@ -310,6 +310,7 @@
 	 */
 	struct e1000_ring *tx_ring /* One per active queue */
 						____cacheline_aligned_in_smp;
+	u32 tx_fifo_limit;
 
 	struct napi_struct napi;
 
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 46c3b1f..d01a099 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -3517,6 +3517,15 @@
 	}
 
 	/*
+	 * Alignment of Tx data is on an arbitrary byte boundary with the
+	 * maximum size per Tx descriptor limited only to the transmit
+	 * allocation of the packet buffer minus 96 bytes with an upper
+	 * limit of 24KB due to receive synchronization limitations.
+	 */
+	adapter->tx_fifo_limit = min_t(u32, ((er32(PBA) >> 16) << 10) - 96,
+				       24 << 10);
+
+	/*
 	 * Disable Adaptive Interrupt Moderation if 2 full packets cannot
 	 * fit in receive buffer.
 	 */
@@ -4785,12 +4794,9 @@
 	return 1;
 }
 
-#define E1000_MAX_PER_TXD	8192
-#define E1000_MAX_TXD_PWR	12
-
 static int e1000_tx_map(struct e1000_ring *tx_ring, struct sk_buff *skb,
 			unsigned int first, unsigned int max_per_txd,
-			unsigned int nr_frags, unsigned int mss)
+			unsigned int nr_frags)
 {
 	struct e1000_adapter *adapter = tx_ring->adapter;
 	struct pci_dev *pdev = adapter->pdev;
@@ -5023,20 +5029,19 @@
 
 static int e1000_maybe_stop_tx(struct e1000_ring *tx_ring, int size)
 {
+	BUG_ON(size > tx_ring->count);
+
 	if (e1000_desc_unused(tx_ring) >= size)
 		return 0;
 	return __e1000_maybe_stop_tx(tx_ring, size);
 }
 
-#define TXD_USE_COUNT(S, X) (((S) >> (X)) + 1)
 static netdev_tx_t e1000_xmit_frame(struct sk_buff *skb,
 				    struct net_device *netdev)
 {
 	struct e1000_adapter *adapter = netdev_priv(netdev);
 	struct e1000_ring *tx_ring = adapter->tx_ring;
 	unsigned int first;
-	unsigned int max_per_txd = E1000_MAX_PER_TXD;
-	unsigned int max_txd_pwr = E1000_MAX_TXD_PWR;
 	unsigned int tx_flags = 0;
 	unsigned int len = skb_headlen(skb);
 	unsigned int nr_frags;
@@ -5056,18 +5061,8 @@
 	}
 
 	mss = skb_shinfo(skb)->gso_size;
-	/*
-	 * The controller does a simple calculation to
-	 * make sure there is enough room in the FIFO before
-	 * initiating the DMA for each buffer.  The calc is:
-	 * 4 = ceil(buffer len/mss).  To make sure we don't
-	 * overrun the FIFO, adjust the max buffer len if mss
-	 * drops.
-	 */
 	if (mss) {
 		u8 hdr_len;
-		max_per_txd = min(mss << 2, max_per_txd);
-		max_txd_pwr = fls(max_per_txd) - 1;
 
 		/*
 		 * TSO Workaround for 82571/2/3 Controllers -- if skb->data
@@ -5097,12 +5092,12 @@
 		count++;
 	count++;
 
-	count += TXD_USE_COUNT(len, max_txd_pwr);
+	count += DIV_ROUND_UP(len, adapter->tx_fifo_limit);
 
 	nr_frags = skb_shinfo(skb)->nr_frags;
 	for (f = 0; f < nr_frags; f++)
-		count += TXD_USE_COUNT(skb_frag_size(&skb_shinfo(skb)->frags[f]),
-				       max_txd_pwr);
+		count += DIV_ROUND_UP(skb_frag_size(&skb_shinfo(skb)->frags[f]),
+				      adapter->tx_fifo_limit);
 
 	if (adapter->hw.mac.tx_pkt_filtering)
 		e1000_transfer_dhcp_info(adapter, skb);
@@ -5144,15 +5139,18 @@
 		tx_flags |= E1000_TX_FLAGS_NO_FCS;
 
 	/* if count is 0 then mapping error has occurred */
-	count = e1000_tx_map(tx_ring, skb, first, max_per_txd, nr_frags, mss);
+	count = e1000_tx_map(tx_ring, skb, first, adapter->tx_fifo_limit,
+			     nr_frags);
 	if (count) {
 		skb_tx_timestamp(skb);
 
 		netdev_sent_queue(netdev, skb->len);
 		e1000_tx_queue(tx_ring, tx_flags, count);
 		/* Make sure there is space in the ring for the next send. */
-		e1000_maybe_stop_tx(tx_ring, MAX_SKB_FRAGS + 2);
-
+		e1000_maybe_stop_tx(tx_ring,
+				    (MAX_SKB_FRAGS *
+				     DIV_ROUND_UP(PAGE_SIZE,
+						  adapter->tx_fifo_limit) + 2));
 	} else {
 		dev_kfree_skb_any(skb);
 		tx_ring->buffer_info[first].time_stamp = 0;
@@ -6327,8 +6325,8 @@
 	adapter->hw.phy.autoneg_advertised = 0x2f;
 
 	/* ring size defaults */
-	adapter->rx_ring->count = 256;
-	adapter->tx_ring->count = 256;
+	adapter->rx_ring->count = E1000_DEFAULT_RXD;
+	adapter->tx_ring->count = E1000_DEFAULT_TXD;
 
 	/*
 	 * Initial Wake on LAN setting - If APM wake is enabled in
diff --git a/drivers/net/ethernet/sfc/ethtool.c b/drivers/net/ethernet/sfc/ethtool.c
index 8cba2df..5faedd8 100644
--- a/drivers/net/ethernet/sfc/ethtool.c
+++ b/drivers/net/ethernet/sfc/ethtool.c
@@ -863,8 +863,8 @@
 				       &ip_entry->ip4dst, &ip_entry->pdst);
 	if (rc != 0) {
 		rc = efx_filter_get_ipv4_full(
-			&spec, &proto, &ip_entry->ip4src, &ip_entry->psrc,
-			&ip_entry->ip4dst, &ip_entry->pdst);
+			&spec, &proto, &ip_entry->ip4dst, &ip_entry->pdst,
+			&ip_entry->ip4src, &ip_entry->psrc);
 		EFX_WARN_ON_PARANOID(rc);
 		ip_mask->ip4src = ~0;
 		ip_mask->psrc = ~0;
diff --git a/drivers/net/ethernet/sgi/ioc3-eth.c b/drivers/net/ethernet/sgi/ioc3-eth.c
index b5ba308..3e5519a 100644
--- a/drivers/net/ethernet/sgi/ioc3-eth.c
+++ b/drivers/net/ethernet/sgi/ioc3-eth.c
@@ -1147,15 +1147,17 @@
 {
 #define COSMISC_CONSTANT 6
 
-	struct uart_port port = {
-		.irq		= 0,
-		.flags		= UPF_SKIP_TEST | UPF_BOOT_AUTOCONF,
-		.iotype		= UPIO_MEM,
-		.regshift	= 0,
-		.uartclk	= (22000000 << 1) / COSMISC_CONSTANT,
+	struct uart_8250_port port = {
+	        .port = {
+			.irq		= 0,
+			.flags		= UPF_SKIP_TEST | UPF_BOOT_AUTOCONF,
+			.iotype		= UPIO_MEM,
+			.regshift	= 0,
+			.uartclk	= (22000000 << 1) / COSMISC_CONSTANT,
 
-		.membase	= (unsigned char __iomem *) uart,
-		.mapbase	= (unsigned long) uart,
+			.membase	= (unsigned char __iomem *) uart,
+			.mapbase	= (unsigned long) uart,
+                }
 	};
 	unsigned char lcr;
 
@@ -1164,7 +1166,7 @@
 	uart->iu_scr = COSMISC_CONSTANT,
 	uart->iu_lcr = lcr;
 	uart->iu_lcr;
-	serial8250_register_port(&port);
+	serial8250_register_8250_port(&port);
 }
 
 static void __devinit ioc3_serial_probe(struct pci_dev *pdev, struct ioc3 *ioc3)
diff --git a/drivers/net/ethernet/stmicro/stmmac/common.h b/drivers/net/ethernet/stmicro/stmmac/common.h
index e2d0832..719be39 100644
--- a/drivers/net/ethernet/stmicro/stmmac/common.h
+++ b/drivers/net/ethernet/stmicro/stmmac/common.h
@@ -22,6 +22,9 @@
   Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>
 *******************************************************************************/
 
+#ifndef __COMMON_H__
+#define __COMMON_H__
+
 #include <linux/etherdevice.h>
 #include <linux/netdevice.h>
 #include <linux/phy.h>
@@ -366,3 +369,5 @@
 
 extern void dwmac_dma_flush_tx_fifo(void __iomem *ioaddr);
 extern const struct stmmac_ring_mode_ops ring_mode_ops;
+
+#endif /* __COMMON_H__ */
diff --git a/drivers/net/ethernet/stmicro/stmmac/descs.h b/drivers/net/ethernet/stmicro/stmmac/descs.h
index 9820ec8..223adf9 100644
--- a/drivers/net/ethernet/stmicro/stmmac/descs.h
+++ b/drivers/net/ethernet/stmicro/stmmac/descs.h
@@ -20,6 +20,10 @@
 
   Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>
 *******************************************************************************/
+
+#ifndef __DESCS_H__
+#define __DESCS_H__
+
 struct dma_desc {
 	/* Receive descriptor */
 	union {
@@ -166,3 +170,5 @@
 					 * is not calculated */
 	cic_full = 3,		/* IP header and pseudoheader */
 };
+
+#endif /* __DESCS_H__ */
diff --git a/drivers/net/ethernet/stmicro/stmmac/descs_com.h b/drivers/net/ethernet/stmicro/stmmac/descs_com.h
index dd8d6e1..7ee9499 100644
--- a/drivers/net/ethernet/stmicro/stmmac/descs_com.h
+++ b/drivers/net/ethernet/stmicro/stmmac/descs_com.h
@@ -27,6 +27,9 @@
   Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>
 *******************************************************************************/
 
+#ifndef __DESC_COM_H__
+#define __DESC_COM_H__
+
 #if defined(CONFIG_STMMAC_RING)
 static inline void ehn_desc_rx_set_on_ring_chain(struct dma_desc *p, int end)
 {
@@ -124,3 +127,5 @@
 	p->des01.tx.buffer1_size = len;
 }
 #endif
+
+#endif /* __DESC_COM_H__ */
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac100.h b/drivers/net/ethernet/stmicro/stmmac/dwmac100.h
index 7c6d857..2ec6aea 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac100.h
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac100.h
@@ -22,6 +22,9 @@
   Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>
 *******************************************************************************/
 
+#ifndef __DWMAC100_H__
+#define __DWMAC100_H__
+
 #include <linux/phy.h>
 #include "common.h"
 
@@ -119,3 +122,5 @@
 #define DMA_MISSED_FRAME_M_CNTR	0x0000ffff	/* Missed Frame Couinter */
 
 extern const struct stmmac_dma_ops dwmac100_dma_ops;
+
+#endif /* __DWMAC100_H__ */
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac1000.h b/drivers/net/ethernet/stmicro/stmmac/dwmac1000.h
index f90fcb5..0e4cace 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac1000.h
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac1000.h
@@ -19,6 +19,8 @@
 
   Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>
 *******************************************************************************/
+#ifndef __DWMAC1000_H__
+#define __DWMAC1000_H__
 
 #include <linux/phy.h>
 #include "common.h"
@@ -229,6 +231,7 @@
 #define GMAC_MMC_RX_CSUM_OFFLOAD   0x208
 
 /* Synopsys Core versions */
-#define	DWMAC_CORE_3_40	34
+#define	DWMAC_CORE_3_40	0x34
 
 extern const struct stmmac_dma_ops dwmac1000_dma_ops;
+#endif /* __DWMAC1000_H__ */
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h b/drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h
index e678ce3..e49c9a0 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h
@@ -22,6 +22,9 @@
   Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>
 *******************************************************************************/
 
+#ifndef __DWMAC_DMA_H__
+#define __DWMAC_DMA_H__
+
 /* DMA CRS Control and Status Register Mapping */
 #define DMA_BUS_MODE		0x00001000	/* Bus Mode */
 #define DMA_XMT_POLL_DEMAND	0x00001004	/* Transmit Poll Demand */
@@ -109,3 +112,5 @@
 extern void dwmac_dma_stop_rx(void __iomem *ioaddr);
 extern int dwmac_dma_interrupt(void __iomem *ioaddr,
 				struct stmmac_extra_stats *x);
+
+#endif /* __DWMAC_DMA_H__ */
diff --git a/drivers/net/ethernet/stmicro/stmmac/mmc.h b/drivers/net/ethernet/stmicro/stmmac/mmc.h
index a3835202..67995ef 100644
--- a/drivers/net/ethernet/stmicro/stmmac/mmc.h
+++ b/drivers/net/ethernet/stmicro/stmmac/mmc.h
@@ -22,6 +22,9 @@
   Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>
 *******************************************************************************/
 
+#ifndef __MMC_H__
+#define __MMC_H__
+
 /* MMC control register */
 /* When set, all counter are reset */
 #define MMC_CNTRL_COUNTER_RESET		0x1
@@ -129,3 +132,5 @@
 extern void dwmac_mmc_ctrl(void __iomem *ioaddr, unsigned int mode);
 extern void dwmac_mmc_intr_all_mask(void __iomem *ioaddr);
 extern void dwmac_mmc_read(void __iomem *ioaddr, struct stmmac_counters *mmc);
+
+#endif /* __MMC_H__ */
diff --git a/drivers/net/ethernet/stmicro/stmmac/mmc_core.c b/drivers/net/ethernet/stmicro/stmmac/mmc_core.c
index c07cfe9..0c74a70 100644
--- a/drivers/net/ethernet/stmicro/stmmac/mmc_core.c
+++ b/drivers/net/ethernet/stmicro/stmmac/mmc_core.c
@@ -33,7 +33,7 @@
 #define MMC_TX_INTR		0x00000108	/* MMC TX Interrupt */
 #define MMC_RX_INTR_MASK	0x0000010c	/* MMC Interrupt Mask */
 #define MMC_TX_INTR_MASK	0x00000110	/* MMC Interrupt Mask */
-#define MMC_DEFAUL_MASK		0xffffffff
+#define MMC_DEFAULT_MASK		0xffffffff
 
 /* MMC TX counter registers */
 
@@ -147,8 +147,8 @@
 /* To mask all all interrupts.*/
 void dwmac_mmc_intr_all_mask(void __iomem *ioaddr)
 {
-	writel(MMC_DEFAUL_MASK, ioaddr + MMC_RX_INTR_MASK);
-	writel(MMC_DEFAUL_MASK, ioaddr + MMC_TX_INTR_MASK);
+	writel(MMC_DEFAULT_MASK, ioaddr + MMC_RX_INTR_MASK);
+	writel(MMC_DEFAULT_MASK, ioaddr + MMC_TX_INTR_MASK);
 }
 
 /* This reads the MAC core counters (if actaully supported).
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac.h b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
index f2d3665..e872e1d 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac.h
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
@@ -20,6 +20,9 @@
   Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>
 *******************************************************************************/
 
+#ifndef __STMMAC_H__
+#define __STMMAC_H__
+
 #define STMMAC_RESOURCE_NAME   "stmmaceth"
 #define DRV_MODULE_VERSION	"March_2012"
 
@@ -166,3 +169,5 @@
 {
 }
 #endif /* CONFIG_STMMAC_PCI */
+
+#endif /* __STMMAC_H__ */
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_timer.h b/drivers/net/ethernet/stmicro/stmmac/stmmac_timer.h
index 6863590..aea9b14 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_timer.h
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_timer.h
@@ -21,6 +21,8 @@
 
   Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>
 *******************************************************************************/
+#ifndef __STMMAC_TIMER_H__
+#define __STMMAC_TIMER_H__
 
 struct stmmac_timer {
 	void (*timer_start) (unsigned int new_freq);
@@ -40,3 +42,5 @@
 extern int tmu2_register_user(void *fnt, void *data);
 extern void tmu2_unregister_user(void);
 #endif
+
+#endif /* __STMMAC_TIMER_H__ */
diff --git a/drivers/net/ethernet/ti/davinci_mdio.c b/drivers/net/ethernet/ti/davinci_mdio.c
index cd7ee20..a9ca4a0 100644
--- a/drivers/net/ethernet/ti/davinci_mdio.c
+++ b/drivers/net/ethernet/ti/davinci_mdio.c
@@ -394,8 +394,10 @@
 	struct device *dev = &pdev->dev;
 	struct davinci_mdio_data *data = dev_get_drvdata(dev);
 
-	if (data->bus)
+	if (data->bus) {
+		mdiobus_unregister(data->bus);
 		mdiobus_free(data->bus);
+	}
 
 	if (data->clk)
 		clk_put(data->clk);
diff --git a/drivers/net/fddi/skfp/pmf.c b/drivers/net/fddi/skfp/pmf.c
index 24d8566..441b4dc 100644
--- a/drivers/net/fddi/skfp/pmf.c
+++ b/drivers/net/fddi/skfp/pmf.c
@@ -673,7 +673,7 @@
 			sm_pm_get_ls(smc,port_to_mib(smc,port))) ;
 		break ;
 	case SMT_P_REASON :
-		* (u_long *) to = 0 ;
+		*(u32 *)to = 0 ;
 		sp_len = 4 ;
 		goto sp_done ;
 	case SMT_P1033 :			/* time stamp */
diff --git a/drivers/net/irda/irtty-sir.c b/drivers/net/irda/irtty-sir.c
index 3352b24..30087ca 100644
--- a/drivers/net/irda/irtty-sir.c
+++ b/drivers/net/irda/irtty-sir.c
@@ -124,8 +124,8 @@
 	tty = priv->tty;
 
 	mutex_lock(&tty->termios_mutex);
-	old_termios = *(tty->termios);
-	cflag = tty->termios->c_cflag;
+	old_termios = tty->termios;
+	cflag = tty->termios.c_cflag;
 	tty_encode_baud_rate(tty, speed, speed);
 	if (tty->ops->set_termios)
 		tty->ops->set_termios(tty, &old_termios);
@@ -281,15 +281,15 @@
 	int cflag;
 
 	mutex_lock(&tty->termios_mutex);
-	old_termios = *(tty->termios);
-	cflag = tty->termios->c_cflag;
+	old_termios = tty->termios;
+	cflag = tty->termios.c_cflag;
 	
 	if (stop)
 		cflag &= ~CREAD;
 	else
 		cflag |= CREAD;
 
-	tty->termios->c_cflag = cflag;
+	tty->termios.c_cflag = cflag;
 	if (tty->ops->set_termios)
 		tty->ops->set_termios(tty, &old_termios);
 	mutex_unlock(&tty->termios_mutex);
diff --git a/drivers/net/usb/hso.c b/drivers/net/usb/hso.c
index 62f30b4..605a4ba 100644
--- a/drivers/net/usb/hso.c
+++ b/drivers/net/usb/hso.c
@@ -1107,7 +1107,6 @@
 				    struct ktermios *old)
 {
 	struct hso_serial *serial = tty->driver_data;
-	struct ktermios *termios;
 
 	if (!serial) {
 		printk(KERN_ERR "%s: no tty structures", __func__);
@@ -1119,16 +1118,15 @@
 	/*
 	 *	Fix up unsupported bits
 	 */
-	termios = tty->termios;
-	termios->c_iflag &= ~IXON; /* disable enable XON/XOFF flow control */
+	tty->termios.c_iflag &= ~IXON; /* disable enable XON/XOFF flow control */
 
-	termios->c_cflag &=
+	tty->termios.c_cflag &=
 		~(CSIZE		/* no size */
 		| PARENB	/* disable parity bit */
 		| CBAUD		/* clear current baud rate */
 		| CBAUDEX);	/* clear current buad rate */
 
-	termios->c_cflag |= CS8;	/* character size 8 bits */
+	tty->termios.c_cflag |= CS8;	/* character size 8 bits */
 
 	/* baud rate 115200 */
 	tty_encode_baud_rate(tty, 115200, 115200);
@@ -1425,14 +1423,14 @@
 
 	if (old)
 		D5("Termios called with: cflags new[%d] - old[%d]",
-		   tty->termios->c_cflag, old->c_cflag);
+		   tty->termios.c_cflag, old->c_cflag);
 
 	/* the actual setup */
 	spin_lock_irqsave(&serial->serial_lock, flags);
 	if (serial->port.count)
 		_hso_serial_set_termios(tty, old);
 	else
-		tty->termios = old;
+		tty->termios = *old;
 	spin_unlock_irqrestore(&serial->serial_lock, flags);
 
 	/* done */
@@ -2289,9 +2287,11 @@
 	if (minor < 0)
 		goto exit;
 
+	tty_port_init(&serial->port);
+
 	/* register our minor number */
-	serial->parent->dev = tty_register_device(tty_drv, minor,
-					&serial->parent->interface->dev);
+	serial->parent->dev = tty_port_register_device(&serial->port, tty_drv,
+			minor, &serial->parent->interface->dev);
 	dev = serial->parent->dev;
 	dev_set_drvdata(dev, serial->parent);
 	i = device_create_file(dev, &dev_attr_hsotype);
@@ -2300,7 +2300,6 @@
 	serial->minor = minor;
 	serial->magic = HSO_SERIAL_MAGIC;
 	spin_lock_init(&serial->serial_lock);
-	tty_port_init(&serial->port);
 	serial->num_rx_urbs = num_urbs;
 
 	/* RX, allocate urb and initialize */
diff --git a/drivers/net/usb/qmi_wwan.c b/drivers/net/usb/qmi_wwan.c
index 328397c..adfab3f 100644
--- a/drivers/net/usb/qmi_wwan.c
+++ b/drivers/net/usb/qmi_wwan.c
@@ -413,7 +413,9 @@
 
 	/* 5. Gobi 2000 and 3000 devices */
 	{QMI_GOBI_DEVICE(0x413c, 0x8186)},	/* Dell Gobi 2000 Modem device (N0218, VU936) */
+	{QMI_GOBI_DEVICE(0x413c, 0x8194)},	/* Dell Gobi 3000 Composite */
 	{QMI_GOBI_DEVICE(0x05c6, 0x920b)},	/* Generic Gobi 2000 Modem device */
+	{QMI_GOBI_DEVICE(0x05c6, 0x920d)},	/* Gobi 3000 Composite */
 	{QMI_GOBI_DEVICE(0x05c6, 0x9225)},	/* Sony Gobi 2000 Modem device (N0279, VU730) */
 	{QMI_GOBI_DEVICE(0x05c6, 0x9245)},	/* Samsung Gobi 2000 Modem device (VL176) */
 	{QMI_GOBI_DEVICE(0x03f0, 0x251d)},	/* HP Gobi 2000 Modem device (VP412) */
@@ -441,6 +443,8 @@
 	{QMI_GOBI_DEVICE(0x1199, 0x9015)},	/* Sierra Wireless Gobi 3000 Modem device */
 	{QMI_GOBI_DEVICE(0x1199, 0x9019)},	/* Sierra Wireless Gobi 3000 Modem device */
 	{QMI_GOBI_DEVICE(0x1199, 0x901b)},	/* Sierra Wireless MC7770 */
+	{QMI_GOBI_DEVICE(0x12d1, 0x14f1)},	/* Sony Gobi 3000 Composite */
+	{QMI_GOBI_DEVICE(0x1410, 0xa021)},	/* Foxconn Gobi 3000 Modem device (Novatel E396) */
 
 	{ }					/* END */
 };
diff --git a/drivers/net/usb/usbnet.c b/drivers/net/usb/usbnet.c
index 8531c1c..fd4b26d 100644
--- a/drivers/net/usb/usbnet.c
+++ b/drivers/net/usb/usbnet.c
@@ -1573,7 +1573,7 @@
 				netif_device_present(dev->net) &&
 				!timer_pending(&dev->delay) &&
 				!test_bit(EVENT_RX_HALT, &dev->flags))
-					rx_alloc_submit(dev, GFP_KERNEL);
+					rx_alloc_submit(dev, GFP_NOIO);
 
 			if (!(dev->txq.qlen >= TX_QLEN(dev)))
 				netif_tx_wake_all_queues(dev->net);
diff --git a/drivers/net/wireless/ath/ath5k/eeprom.c b/drivers/net/wireless/ath/ath5k/eeprom.c
index 4026c90..b7e0258 100644
--- a/drivers/net/wireless/ath/ath5k/eeprom.c
+++ b/drivers/net/wireless/ath/ath5k/eeprom.c
@@ -1482,7 +1482,7 @@
 	case AR5K_EEPROM_MODE_11A:
 		offset += AR5K_EEPROM_TARGET_PWR_OFF_11A(ee->ee_version);
 		rate_pcal_info = ee->ee_rate_tpwr_a;
-		ee->ee_rate_target_pwr_num[mode] = AR5K_EEPROM_N_5GHZ_CHAN;
+		ee->ee_rate_target_pwr_num[mode] = AR5K_EEPROM_N_5GHZ_RATE_CHAN;
 		break;
 	case AR5K_EEPROM_MODE_11B:
 		offset += AR5K_EEPROM_TARGET_PWR_OFF_11B(ee->ee_version);
diff --git a/drivers/net/wireless/ath/ath5k/eeprom.h b/drivers/net/wireless/ath/ath5k/eeprom.h
index dc2bcfe..94a9bbe 100644
--- a/drivers/net/wireless/ath/ath5k/eeprom.h
+++ b/drivers/net/wireless/ath/ath5k/eeprom.h
@@ -182,6 +182,7 @@
 #define AR5K_EEPROM_EEP_DELTA		10
 #define AR5K_EEPROM_N_MODES		3
 #define AR5K_EEPROM_N_5GHZ_CHAN		10
+#define AR5K_EEPROM_N_5GHZ_RATE_CHAN	8
 #define AR5K_EEPROM_N_2GHZ_CHAN		3
 #define AR5K_EEPROM_N_2GHZ_CHAN_2413	4
 #define	AR5K_EEPROM_N_2GHZ_CHAN_MAX	4
diff --git a/drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.c b/drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.c
index 192ad5c..a5edebe 100644
--- a/drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.c
+++ b/drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.c
@@ -1233,6 +1233,9 @@
 	/* dpc will not be rescheduled */
 	wl->resched = false;
 
+	/* inform publicly that interface is down */
+	wl->pub->up = false;
+
 	return 0;
 }
 
diff --git a/drivers/net/wireless/ipw2x00/ipw2100.c b/drivers/net/wireless/ipw2x00/ipw2100.c
index 95aa8e1..83324b3 100644
--- a/drivers/net/wireless/ipw2x00/ipw2100.c
+++ b/drivers/net/wireless/ipw2x00/ipw2100.c
@@ -2042,7 +2042,8 @@
 		return;
 	}
 	len = ETH_ALEN;
-	ipw2100_get_ordinal(priv, IPW_ORD_STAT_ASSN_AP_BSSID, &bssid, &len);
+	ret = ipw2100_get_ordinal(priv, IPW_ORD_STAT_ASSN_AP_BSSID, bssid,
+				  &len);
 	if (ret) {
 		IPW_DEBUG_INFO("failed querying ordinals at line %d\n",
 			       __LINE__);
diff --git a/drivers/net/wireless/iwlwifi/dvm/debugfs.c b/drivers/net/wireless/iwlwifi/dvm/debugfs.c
index 46782f1..a47b306 100644
--- a/drivers/net/wireless/iwlwifi/dvm/debugfs.c
+++ b/drivers/net/wireless/iwlwifi/dvm/debugfs.c
@@ -124,6 +124,9 @@
 	const struct fw_img *img;
 	size_t bufsz;
 
+	if (!iwl_is_ready_rf(priv))
+		return -EAGAIN;
+
 	/* default is to dump the entire data segment */
 	if (!priv->dbgfs_sram_offset && !priv->dbgfs_sram_len) {
 		priv->dbgfs_sram_offset = 0x800000;
diff --git a/drivers/net/wireless/iwlwifi/pcie/internal.h b/drivers/net/wireless/iwlwifi/pcie/internal.h
index d9694c5..4ffc18d 100644
--- a/drivers/net/wireless/iwlwifi/pcie/internal.h
+++ b/drivers/net/wireless/iwlwifi/pcie/internal.h
@@ -350,7 +350,7 @@
 /*****************************************************
 * Error handling
 ******************************************************/
-int iwl_dump_fh(struct iwl_trans *trans, char **buf, bool display);
+int iwl_dump_fh(struct iwl_trans *trans, char **buf);
 void iwl_dump_csr(struct iwl_trans *trans);
 
 /*****************************************************
diff --git a/drivers/net/wireless/iwlwifi/pcie/rx.c b/drivers/net/wireless/iwlwifi/pcie/rx.c
index 39a6ca1..d1a61ba 100644
--- a/drivers/net/wireless/iwlwifi/pcie/rx.c
+++ b/drivers/net/wireless/iwlwifi/pcie/rx.c
@@ -555,7 +555,7 @@
 	}
 
 	iwl_dump_csr(trans);
-	iwl_dump_fh(trans, NULL, false);
+	iwl_dump_fh(trans, NULL);
 
 	iwl_op_mode_nic_error(trans->op_mode);
 }
diff --git a/drivers/net/wireless/iwlwifi/pcie/trans.c b/drivers/net/wireless/iwlwifi/pcie/trans.c
index 939c2f7..1e86ea2 100644
--- a/drivers/net/wireless/iwlwifi/pcie/trans.c
+++ b/drivers/net/wireless/iwlwifi/pcie/trans.c
@@ -1649,13 +1649,9 @@
 #undef IWL_CMD
 }
 
-int iwl_dump_fh(struct iwl_trans *trans, char **buf, bool display)
+int iwl_dump_fh(struct iwl_trans *trans, char **buf)
 {
 	int i;
-#ifdef CONFIG_IWLWIFI_DEBUG
-	int pos = 0;
-	size_t bufsz = 0;
-#endif
 	static const u32 fh_tbl[] = {
 		FH_RSCSR_CHNL0_STTS_WPTR_REG,
 		FH_RSCSR_CHNL0_RBDCB_BASE_REG,
@@ -1667,29 +1663,35 @@
 		FH_TSSR_TX_STATUS_REG,
 		FH_TSSR_TX_ERROR_REG
 	};
-#ifdef CONFIG_IWLWIFI_DEBUG
-	if (display) {
-		bufsz = ARRAY_SIZE(fh_tbl) * 48 + 40;
+
+#ifdef CONFIG_IWLWIFI_DEBUGFS
+	if (buf) {
+		int pos = 0;
+		size_t bufsz = ARRAY_SIZE(fh_tbl) * 48 + 40;
+
 		*buf = kmalloc(bufsz, GFP_KERNEL);
 		if (!*buf)
 			return -ENOMEM;
+
 		pos += scnprintf(*buf + pos, bufsz - pos,
 				"FH register values:\n");
-		for (i = 0; i < ARRAY_SIZE(fh_tbl); i++) {
+
+		for (i = 0; i < ARRAY_SIZE(fh_tbl); i++)
 			pos += scnprintf(*buf + pos, bufsz - pos,
 				"  %34s: 0X%08x\n",
 				get_fh_string(fh_tbl[i]),
 				iwl_read_direct32(trans, fh_tbl[i]));
-		}
+
 		return pos;
 	}
 #endif
+
 	IWL_ERR(trans, "FH register values:\n");
-	for (i = 0; i <  ARRAY_SIZE(fh_tbl); i++) {
+	for (i = 0; i <  ARRAY_SIZE(fh_tbl); i++)
 		IWL_ERR(trans, "  %34s: 0X%08x\n",
 			get_fh_string(fh_tbl[i]),
 			iwl_read_direct32(trans, fh_tbl[i]));
-	}
+
 	return 0;
 }
 
@@ -1982,11 +1984,11 @@
 				     size_t count, loff_t *ppos)
 {
 	struct iwl_trans *trans = file->private_data;
-	char *buf;
+	char *buf = NULL;
 	int pos = 0;
 	ssize_t ret = -EFAULT;
 
-	ret = pos = iwl_dump_fh(trans, &buf, true);
+	ret = pos = iwl_dump_fh(trans, &buf);
 	if (buf) {
 		ret = simple_read_from_buffer(user_buf,
 					      count, ppos, buf, pos);
diff --git a/drivers/net/xen-netfront.c b/drivers/net/xen-netfront.c
index 3089990..650f79a 100644
--- a/drivers/net/xen-netfront.c
+++ b/drivers/net/xen-netfront.c
@@ -57,8 +57,7 @@
 static const struct ethtool_ops xennet_ethtool_ops;
 
 struct netfront_cb {
-	struct page *page;
-	unsigned offset;
+	int pull_to;
 };
 
 #define NETFRONT_SKB_CB(skb)	((struct netfront_cb *)((skb)->cb))
@@ -867,15 +866,9 @@
 	struct sk_buff *skb;
 
 	while ((skb = __skb_dequeue(rxq)) != NULL) {
-		struct page *page = NETFRONT_SKB_CB(skb)->page;
-		void *vaddr = page_address(page);
-		unsigned offset = NETFRONT_SKB_CB(skb)->offset;
+		int pull_to = NETFRONT_SKB_CB(skb)->pull_to;
 
-		memcpy(skb->data, vaddr + offset,
-		       skb_headlen(skb));
-
-		if (page != skb_frag_page(&skb_shinfo(skb)->frags[0]))
-			__free_page(page);
+		__pskb_pull_tail(skb, pull_to - skb_headlen(skb));
 
 		/* Ethernet work: Delayed to here as it peeks the header. */
 		skb->protocol = eth_type_trans(skb, dev);
@@ -913,7 +906,6 @@
 	struct sk_buff_head errq;
 	struct sk_buff_head tmpq;
 	unsigned long flags;
-	unsigned int len;
 	int err;
 
 	spin_lock(&np->rx_lock);
@@ -955,24 +947,13 @@
 			}
 		}
 
-		NETFRONT_SKB_CB(skb)->page =
-			skb_frag_page(&skb_shinfo(skb)->frags[0]);
-		NETFRONT_SKB_CB(skb)->offset = rx->offset;
+		NETFRONT_SKB_CB(skb)->pull_to = rx->status;
+		if (NETFRONT_SKB_CB(skb)->pull_to > RX_COPY_THRESHOLD)
+			NETFRONT_SKB_CB(skb)->pull_to = RX_COPY_THRESHOLD;
 
-		len = rx->status;
-		if (len > RX_COPY_THRESHOLD)
-			len = RX_COPY_THRESHOLD;
-		skb_put(skb, len);
-
-		if (rx->status > len) {
-			skb_shinfo(skb)->frags[0].page_offset =
-				rx->offset + len;
-			skb_frag_size_set(&skb_shinfo(skb)->frags[0], rx->status - len);
-			skb->data_len = rx->status - len;
-		} else {
-			__skb_fill_page_desc(skb, 0, NULL, 0, 0);
-			skb_shinfo(skb)->nr_frags = 0;
-		}
+		skb_shinfo(skb)->frags[0].page_offset = rx->offset;
+		skb_frag_size_set(&skb_shinfo(skb)->frags[0], rx->status);
+		skb->data_len = rx->status;
 
 		i = xennet_fill_frags(np, skb, &tmpq);
 
@@ -999,7 +980,7 @@
 		 * receive throughout using the standard receive
 		 * buffer size was cut by 25%(!!!).
 		 */
-		skb->truesize += skb->data_len - (RX_COPY_THRESHOLD - len);
+		skb->truesize += skb->data_len - RX_COPY_THRESHOLD;
 		skb->len += skb->data_len;
 
 		if (rx->flags & XEN_NETRXF_csum_blank)
diff --git a/drivers/parport/parport_gsc.c b/drivers/parport/parport_gsc.c
index 5d6de38..352f961 100644
--- a/drivers/parport/parport_gsc.c
+++ b/drivers/parport/parport_gsc.c
@@ -271,6 +271,7 @@
 	if (!parport_SPP_supported (p)) {
 		/* No port. */
 		kfree (priv);
+		kfree(ops);
 		return NULL;
 	}
 	parport_PS2_supported (p);
diff --git a/drivers/parport/parport_serial.c b/drivers/parport/parport_serial.c
index e9c3227..1631eeaf 100644
--- a/drivers/parport/parport_serial.c
+++ b/drivers/parport/parport_serial.c
@@ -62,6 +62,7 @@
 	timedia_9079a,
 	timedia_9079b,
 	timedia_9079c,
+	wch_ch353_2s1p,
 };
 
 /* each element directly indexed from enum list, above */
@@ -145,6 +146,7 @@
 	/* timedia_9079a */             { 1, { { 2, 3 }, } },
 	/* timedia_9079b */             { 1, { { 2, 3 }, } },
 	/* timedia_9079c */             { 1, { { 2, 3 }, } },
+	/* wch_ch353_2s1p*/             { 1, { { 2, -1}, } },
 };
 
 static struct pci_device_id parport_serial_pci_tbl[] = {
@@ -243,7 +245,8 @@
 	{ 0x1409, 0x7168, 0x1409, 0xb079, 0, 0, timedia_9079a },
 	{ 0x1409, 0x7168, 0x1409, 0xc079, 0, 0, timedia_9079b },
 	{ 0x1409, 0x7168, 0x1409, 0xd079, 0, 0, timedia_9079c },
-
+	/* WCH CARDS */
+	{ 0x4348, 0x7053, 0x4348, 0x3253, 0, 0, wch_ch353_2s1p},
 	{ 0, } /* terminate list */
 };
 MODULE_DEVICE_TABLE(pci,parport_serial_pci_tbl);
@@ -460,6 +463,12 @@
 		.base_baud	= 921600,
 		.uart_offset	= 8,
 	},
+	[wch_ch353_2s1p] = {
+		.flags          = FL_BASE0|FL_BASE_BARS,
+		.num_ports      = 2,
+		.base_baud      = 115200,
+		.uart_offset    = 8,
+	},
 };
 
 struct parport_serial_private {
diff --git a/drivers/pci/pci-driver.c b/drivers/pci/pci-driver.c
index 5270f1a..d6fd6b6 100644
--- a/drivers/pci/pci-driver.c
+++ b/drivers/pci/pci-driver.c
@@ -280,8 +280,12 @@
 {
 	struct drv_dev_and_id *ddi = _ddi;
 	struct device *dev = &ddi->dev->dev;
+	struct device *parent = dev->parent;
 	int rc;
 
+	/* The parent bridge must be in active state when probing */
+	if (parent)
+		pm_runtime_get_sync(parent);
 	/* Unbound PCI devices are always set to disabled and suspended.
 	 * During probe, the device is set to enabled and active and the
 	 * usage count is incremented.  If the driver supports runtime PM,
@@ -298,6 +302,8 @@
 		pm_runtime_set_suspended(dev);
 		pm_runtime_put_noidle(dev);
 	}
+	if (parent)
+		pm_runtime_put(parent);
 	return rc;
 }
 
diff --git a/drivers/pci/pci-sysfs.c b/drivers/pci/pci-sysfs.c
index 6869009..02d107b 100644
--- a/drivers/pci/pci-sysfs.c
+++ b/drivers/pci/pci-sysfs.c
@@ -458,6 +458,40 @@
 }
 struct device_attribute vga_attr = __ATTR_RO(boot_vga);
 
+static void
+pci_config_pm_runtime_get(struct pci_dev *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device *parent = dev->parent;
+
+	if (parent)
+		pm_runtime_get_sync(parent);
+	pm_runtime_get_noresume(dev);
+	/*
+	 * pdev->current_state is set to PCI_D3cold during suspending,
+	 * so wait until suspending completes
+	 */
+	pm_runtime_barrier(dev);
+	/*
+	 * Only need to resume devices in D3cold, because config
+	 * registers are still accessible for devices suspended but
+	 * not in D3cold.
+	 */
+	if (pdev->current_state == PCI_D3cold)
+		pm_runtime_resume(dev);
+}
+
+static void
+pci_config_pm_runtime_put(struct pci_dev *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device *parent = dev->parent;
+
+	pm_runtime_put(dev);
+	if (parent)
+		pm_runtime_put_sync(parent);
+}
+
 static ssize_t
 pci_read_config(struct file *filp, struct kobject *kobj,
 		struct bin_attribute *bin_attr,
@@ -484,6 +518,8 @@
 		size = count;
 	}
 
+	pci_config_pm_runtime_get(dev);
+
 	if ((off & 1) && size) {
 		u8 val;
 		pci_user_read_config_byte(dev, off, &val);
@@ -529,6 +565,8 @@
 		--size;
 	}
 
+	pci_config_pm_runtime_put(dev);
+
 	return count;
 }
 
@@ -549,6 +587,8 @@
 		count = size;
 	}
 	
+	pci_config_pm_runtime_get(dev);
+
 	if ((off & 1) && size) {
 		pci_user_write_config_byte(dev, off, data[off - init_off]);
 		off++;
@@ -587,6 +627,8 @@
 		--size;
 	}
 
+	pci_config_pm_runtime_put(dev);
+
 	return count;
 }
 
diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c
index f3ea977..ab4bf5a 100644
--- a/drivers/pci/pci.c
+++ b/drivers/pci/pci.c
@@ -1941,6 +1941,7 @@
 	dev->pm_cap = pm;
 	dev->d3_delay = PCI_PM_D3_WAIT;
 	dev->d3cold_delay = PCI_PM_D3COLD_WAIT;
+	dev->d3cold_allowed = true;
 
 	dev->d1_support = false;
 	dev->d2_support = false;
diff --git a/drivers/pci/pcie/portdrv_pci.c b/drivers/pci/pcie/portdrv_pci.c
index 3a7eefc..e76b447 100644
--- a/drivers/pci/pcie/portdrv_pci.c
+++ b/drivers/pci/pcie/portdrv_pci.c
@@ -140,9 +140,17 @@
 {
 	return 0;
 }
+
+static int pcie_port_runtime_idle(struct device *dev)
+{
+	/* Delay for a short while to prevent too frequent suspend/resume */
+	pm_schedule_suspend(dev, 10);
+	return -EBUSY;
+}
 #else
 #define pcie_port_runtime_suspend	NULL
 #define pcie_port_runtime_resume	NULL
+#define pcie_port_runtime_idle		NULL
 #endif
 
 static const struct dev_pm_ops pcie_portdrv_pm_ops = {
@@ -155,6 +163,7 @@
 	.resume_noirq	= pcie_port_resume_noirq,
 	.runtime_suspend = pcie_port_runtime_suspend,
 	.runtime_resume = pcie_port_runtime_resume,
+	.runtime_idle	= pcie_port_runtime_idle,
 };
 
 #define PCIE_PORTDRV_PM_OPS	(&pcie_portdrv_pm_ops)
@@ -200,6 +209,11 @@
 		return status;
 
 	pci_save_state(dev);
+	/*
+	 * D3cold may not work properly on some PCIe port, so disable
+	 * it by default.
+	 */
+	dev->d3cold_allowed = false;
 	if (!pci_match_id(port_runtime_pm_black_list, dev))
 		pm_runtime_put_noidle(&dev->dev);
 
diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c
index 6c143b4..9f8a6b7 100644
--- a/drivers/pci/probe.c
+++ b/drivers/pci/probe.c
@@ -144,15 +144,13 @@
 	case PCI_BASE_ADDRESS_MEM_TYPE_32:
 		break;
 	case PCI_BASE_ADDRESS_MEM_TYPE_1M:
-		dev_info(&dev->dev, "1M mem BAR treated as 32-bit BAR\n");
+		/* 1M mem BAR treated as 32-bit BAR */
 		break;
 	case PCI_BASE_ADDRESS_MEM_TYPE_64:
 		flags |= IORESOURCE_MEM_64;
 		break;
 	default:
-		dev_warn(&dev->dev,
-			 "mem unknown type %x treated as 32-bit BAR\n",
-			 mem_type);
+		/* mem unknown type treated as 32-bit BAR */
 		break;
 	}
 	return flags;
@@ -173,9 +171,11 @@
 	u32 l, sz, mask;
 	u16 orig_cmd;
 	struct pci_bus_region region;
+	bool bar_too_big = false, bar_disabled = false;
 
 	mask = type ? PCI_ROM_ADDRESS_MASK : ~0;
 
+	/* No printks while decoding is disabled! */
 	if (!dev->mmio_always_on) {
 		pci_read_config_word(dev, PCI_COMMAND, &orig_cmd);
 		pci_write_config_word(dev, PCI_COMMAND,
@@ -240,8 +240,7 @@
 			goto fail;
 
 		if ((sizeof(resource_size_t) < 8) && (sz64 > 0x100000000ULL)) {
-			dev_err(&dev->dev, "reg %x: can't handle 64-bit BAR\n",
-				pos);
+			bar_too_big = true;
 			goto fail;
 		}
 
@@ -252,12 +251,11 @@
 			region.start = 0;
 			region.end = sz64;
 			pcibios_bus_to_resource(dev, res, &region);
+			bar_disabled = true;
 		} else {
 			region.start = l64;
 			region.end = l64 + sz64;
 			pcibios_bus_to_resource(dev, res, &region);
-			dev_printk(KERN_DEBUG, &dev->dev, "reg %x: %pR\n",
-				   pos, res);
 		}
 	} else {
 		sz = pci_size(l, sz, mask);
@@ -268,18 +266,23 @@
 		region.start = l;
 		region.end = l + sz;
 		pcibios_bus_to_resource(dev, res, &region);
-
-		dev_printk(KERN_DEBUG, &dev->dev, "reg %x: %pR\n", pos, res);
 	}
 
- out:
+	goto out;
+
+
+fail:
+	res->flags = 0;
+out:
 	if (!dev->mmio_always_on)
 		pci_write_config_word(dev, PCI_COMMAND, orig_cmd);
 
+	if (bar_too_big)
+		dev_err(&dev->dev, "reg %x: can't handle 64-bit BAR\n", pos);
+	if (res->flags && !bar_disabled)
+		dev_printk(KERN_DEBUG, &dev->dev, "reg %x: %pR\n", pos, res);
+
 	return (res->flags & IORESOURCE_MEM_64) ? 1 : 0;
- fail:
-	res->flags = 0;
-	goto out;
 }
 
 static void pci_read_bases(struct pci_dev *dev, unsigned int howmany, int rom)
diff --git a/drivers/rtc/rtc-at91sam9.c b/drivers/rtc/rtc-at91sam9.c
index 8318689..1dd61f4 100644
--- a/drivers/rtc/rtc-at91sam9.c
+++ b/drivers/rtc/rtc-at91sam9.c
@@ -58,6 +58,7 @@
 	struct rtc_device	*rtcdev;
 	u32			imr;
 	void __iomem		*gpbr;
+	int 			irq;
 };
 
 #define rtt_readl(rtc, field) \
@@ -292,7 +293,7 @@
 {
 	struct resource	*r, *r_gpbr;
 	struct sam9_rtc	*rtc;
-	int		ret;
+	int		ret, irq;
 	u32		mr;
 
 	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
@@ -302,10 +303,18 @@
 		return -ENODEV;
 	}
 
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		dev_err(&pdev->dev, "failed to get interrupt resource\n");
+		return irq;
+	}
+
 	rtc = kzalloc(sizeof *rtc, GFP_KERNEL);
 	if (!rtc)
 		return -ENOMEM;
 
+	rtc->irq = irq;
+
 	/* platform setup code should have handled this; sigh */
 	if (!device_can_wakeup(&pdev->dev))
 		device_init_wakeup(&pdev->dev, 1);
@@ -345,11 +354,10 @@
 	}
 
 	/* register irq handler after we know what name we'll use */
-	ret = request_irq(AT91_ID_SYS, at91_rtc_interrupt,
-				IRQF_SHARED,
+	ret = request_irq(rtc->irq, at91_rtc_interrupt, IRQF_SHARED,
 				dev_name(&rtc->rtcdev->dev), rtc);
 	if (ret) {
-		dev_dbg(&pdev->dev, "can't share IRQ %d?\n", AT91_ID_SYS);
+		dev_dbg(&pdev->dev, "can't share IRQ %d?\n", rtc->irq);
 		rtc_device_unregister(rtc->rtcdev);
 		goto fail_register;
 	}
@@ -386,7 +394,7 @@
 
 	/* disable all interrupts */
 	rtt_writel(rtc, MR, mr & ~(AT91_RTT_ALMIEN | AT91_RTT_RTTINCIEN));
-	free_irq(AT91_ID_SYS, rtc);
+	free_irq(rtc->irq, rtc);
 
 	rtc_device_unregister(rtc->rtcdev);
 
@@ -423,7 +431,7 @@
 	rtc->imr = mr & (AT91_RTT_ALMIEN | AT91_RTT_RTTINCIEN);
 	if (rtc->imr) {
 		if (device_may_wakeup(&pdev->dev) && (mr & AT91_RTT_ALMIEN)) {
-			enable_irq_wake(AT91_ID_SYS);
+			enable_irq_wake(rtc->irq);
 			/* don't let RTTINC cause wakeups */
 			if (mr & AT91_RTT_RTTINCIEN)
 				rtt_writel(rtc, MR, mr & ~AT91_RTT_RTTINCIEN);
@@ -441,7 +449,7 @@
 
 	if (rtc->imr) {
 		if (device_may_wakeup(&pdev->dev))
-			disable_irq_wake(AT91_ID_SYS);
+			disable_irq_wake(rtc->irq);
 		mr = rtt_readl(rtc, MR);
 		rtt_writel(rtc, MR, mr | rtc->imr);
 	}
diff --git a/drivers/s390/block/dasd_eckd.c b/drivers/s390/block/dasd_eckd.c
index 40a826a..2fb2b9e 100644
--- a/drivers/s390/block/dasd_eckd.c
+++ b/drivers/s390/block/dasd_eckd.c
@@ -3804,7 +3804,7 @@
 	case BIODASDSYMMIO:
 		return dasd_symm_io(device, argp);
 	default:
-		return -ENOIOCTLCMD;
+		return -ENOTTY;
 	}
 }
 
diff --git a/drivers/s390/block/dasd_ioctl.c b/drivers/s390/block/dasd_ioctl.c
index cceae70..654c692 100644
--- a/drivers/s390/block/dasd_ioctl.c
+++ b/drivers/s390/block/dasd_ioctl.c
@@ -498,12 +498,9 @@
 		break;
 	default:
 		/* if the discipline has an ioctl method try it. */
-		if (base->discipline->ioctl) {
+		rc = -ENOTTY;
+		if (base->discipline->ioctl)
 			rc = base->discipline->ioctl(block, cmd, argp);
-			if (rc == -ENOIOCTLCMD)
-				rc = -EINVAL;
-		} else
-			rc = -EINVAL;
 	}
 	dasd_put_device(base);
 	return rc;
diff --git a/drivers/s390/char/con3215.c b/drivers/s390/char/con3215.c
index 6c0116d..9ffb6d5 100644
--- a/drivers/s390/char/con3215.c
+++ b/drivers/s390/char/con3215.c
@@ -716,10 +716,17 @@
 static void raw3215_remove (struct ccw_device *cdev)
 {
 	struct raw3215_info *raw;
+	unsigned int line;
 
 	ccw_device_set_offline(cdev);
 	raw = dev_get_drvdata(&cdev->dev);
 	if (raw) {
+		spin_lock(&raw3215_device_lock);
+		for (line = 0; line < NR_3215; line++)
+			if (raw3215[line] == raw)
+				break;
+		raw3215[line] = NULL;
+		spin_unlock(&raw3215_device_lock);
 		dev_set_drvdata(&cdev->dev, NULL);
 		raw3215_free_info(raw);
 	}
@@ -935,6 +942,19 @@
 console_initcall(con3215_init);
 #endif
 
+static int tty3215_install(struct tty_driver *driver, struct tty_struct *tty)
+{
+	struct raw3215_info *raw;
+
+	raw = raw3215[tty->index];
+	if (raw == NULL)
+		return -ENODEV;
+
+	tty->driver_data = raw;
+
+	return tty_port_install(&raw->port, driver, tty);
+}
+
 /*
  * tty3215_open
  *
@@ -942,14 +962,9 @@
  */
 static int tty3215_open(struct tty_struct *tty, struct file * filp)
 {
-	struct raw3215_info *raw;
+	struct raw3215_info *raw = tty->driver_data;
 	int retval;
 
-	raw = raw3215[tty->index];
-	if (raw == NULL)
-		return -ENODEV;
-
-	tty->driver_data = raw;
 	tty_port_tty_set(&raw->port, tty);
 
 	tty->low_latency = 0;  /* don't use bottom half for pushing chars */
@@ -1110,6 +1125,7 @@
 }
 
 static const struct tty_operations tty3215_ops = {
+	.install = tty3215_install,
 	.open = tty3215_open,
 	.close = tty3215_close,
 	.write = tty3215_write,
diff --git a/drivers/s390/char/sclp_tty.c b/drivers/s390/char/sclp_tty.c
index 0792c85..30ec09e 100644
--- a/drivers/s390/char/sclp_tty.c
+++ b/drivers/s390/char/sclp_tty.c
@@ -567,6 +567,7 @@
 	driver->init_termios.c_lflag = ISIG | ECHO;
 	driver->flags = TTY_DRIVER_REAL_RAW;
 	tty_set_operations(driver, &sclp_ops);
+	tty_port_link_device(&sclp_port, driver, 0);
 	rc = tty_register_driver(driver);
 	if (rc) {
 		put_tty_driver(driver);
diff --git a/drivers/s390/char/sclp_vt220.c b/drivers/s390/char/sclp_vt220.c
index edfc0fd..7e60f3d 100644
--- a/drivers/s390/char/sclp_vt220.c
+++ b/drivers/s390/char/sclp_vt220.c
@@ -691,6 +691,7 @@
 	driver->init_termios = tty_std_termios;
 	driver->flags = TTY_DRIVER_REAL_RAW;
 	tty_set_operations(driver, &sclp_vt220_ops);
+	tty_port_link_device(&sclp_vt220_port, driver, 0);
 
 	rc = tty_register_driver(driver);
 	if (rc)
diff --git a/drivers/s390/char/tty3270.c b/drivers/s390/char/tty3270.c
index 1928f34..482ee02 100644
--- a/drivers/s390/char/tty3270.c
+++ b/drivers/s390/char/tty3270.c
@@ -842,17 +842,14 @@
 };
 
 /*
- * This routine is called whenever a 3270 tty is opened.
+ * This routine is called whenever a 3270 tty is opened first time.
  */
-static int
-tty3270_open(struct tty_struct *tty, struct file * filp)
+static int tty3270_install(struct tty_driver *driver, struct tty_struct *tty)
 {
 	struct raw3270_view *view;
 	struct tty3270 *tp;
 	int i, rc;
 
-	if (tty->count > 1)
-		return 0;
 	/* Check if the tty3270 is already there. */
 	view = raw3270_find_view(&tty3270_fn,
 				  tty->index + RAW3270_FIRSTMINOR);
@@ -865,7 +862,7 @@
 		/* why to reassign? */
 		tty_port_tty_set(&tp->port, tty);
 		tp->inattr = TF_INPUT;
-		return 0;
+		return tty_port_install(&tp->port, driver, tty);
 	}
 	if (tty3270_max_index < tty->index + 1)
 		tty3270_max_index = tty->index + 1;
@@ -895,7 +892,6 @@
 
 	tty_port_tty_set(&tp->port, tty);
 	tty->low_latency = 0;
-	tty->driver_data = tp;
 	tty->winsize.ws_row = tp->view.rows - 2;
 	tty->winsize.ws_col = tp->view.cols;
 
@@ -915,6 +911,15 @@
 	kbd_ascebc(tp->kbd, tp->view.ascebc);
 
 	raw3270_activate_view(&tp->view);
+
+	rc = tty_port_install(&tp->port, driver, tty);
+	if (rc) {
+		raw3270_put_view(&tp->view);
+		return rc;
+	}
+
+	tty->driver_data = tp;
+
 	return 0;
 }
 
@@ -932,10 +937,17 @@
 	if (tp) {
 		tty->driver_data = NULL;
 		tty_port_tty_set(&tp->port, NULL);
-		raw3270_put_view(&tp->view);
 	}
 }
 
+static void tty3270_cleanup(struct tty_struct *tty)
+{
+	struct tty3270 *tp = tty->driver_data;
+
+	if (tp)
+		raw3270_put_view(&tp->view);
+}
+
 /*
  * We always have room.
  */
@@ -1737,7 +1749,8 @@
 #endif
 
 static const struct tty_operations tty3270_ops = {
-	.open = tty3270_open,
+	.install = tty3270_install,
+	.cleanup = tty3270_cleanup,
 	.close = tty3270_close,
 	.write = tty3270_write,
 	.put_char = tty3270_put_char,
@@ -1781,7 +1794,7 @@
 	driver->type = TTY_DRIVER_TYPE_SYSTEM;
 	driver->subtype = SYSTEM_TYPE_TTY;
 	driver->init_termios = tty_std_termios;
-	driver->flags = TTY_DRIVER_RESET_TERMIOS | TTY_DRIVER_DYNAMIC_DEV;
+	driver->flags = TTY_DRIVER_RESET_TERMIOS;
 	tty_set_operations(driver, &tty3270_ops);
 	ret = tty_register_driver(driver);
 	if (ret) {
@@ -1800,6 +1813,7 @@
 	driver = tty3270_driver;
 	tty3270_driver = NULL;
 	tty_unregister_driver(driver);
+	put_tty_driver(driver);
 	tty3270_del_views();
 }
 
diff --git a/drivers/spi/spi-bcm63xx.c b/drivers/spi/spi-bcm63xx.c
index ea0aaa3..a9f4049 100644
--- a/drivers/spi/spi-bcm63xx.c
+++ b/drivers/spi/spi-bcm63xx.c
@@ -47,6 +47,8 @@
 	/* Platform data */
 	u32			speed_hz;
 	unsigned		fifo_size;
+	unsigned int		msg_type_shift;
+	unsigned int		msg_ctl_width;
 
 	/* Data buffers */
 	const unsigned char	*tx_ptr;
@@ -221,13 +223,20 @@
 	msg_ctl = (t->len << SPI_BYTE_CNT_SHIFT);
 
 	if (t->rx_buf && t->tx_buf)
-		msg_ctl |= (SPI_FD_RW << SPI_MSG_TYPE_SHIFT);
+		msg_ctl |= (SPI_FD_RW << bs->msg_type_shift);
 	else if (t->rx_buf)
-		msg_ctl |= (SPI_HD_R << SPI_MSG_TYPE_SHIFT);
+		msg_ctl |= (SPI_HD_R << bs->msg_type_shift);
 	else if (t->tx_buf)
-		msg_ctl |= (SPI_HD_W << SPI_MSG_TYPE_SHIFT);
+		msg_ctl |= (SPI_HD_W << bs->msg_type_shift);
 
-	bcm_spi_writew(bs, msg_ctl, SPI_MSG_CTL);
+	switch (bs->msg_ctl_width) {
+	case 8:
+		bcm_spi_writeb(bs, msg_ctl, SPI_MSG_CTL);
+		break;
+	case 16:
+		bcm_spi_writew(bs, msg_ctl, SPI_MSG_CTL);
+		break;
+	}
 
 	/* Issue the transfer */
 	cmd = SPI_CMD_START_IMMEDIATE;
@@ -406,9 +415,21 @@
 	master->transfer_one_message = bcm63xx_spi_transfer_one;
 	master->mode_bits = MODEBITS;
 	bs->speed_hz = pdata->speed_hz;
+	bs->msg_type_shift = pdata->msg_type_shift;
+	bs->msg_ctl_width = pdata->msg_ctl_width;
 	bs->tx_io = (u8 *)(bs->regs + bcm63xx_spireg(SPI_MSG_DATA));
 	bs->rx_io = (const u8 *)(bs->regs + bcm63xx_spireg(SPI_RX_DATA));
 
+	switch (bs->msg_ctl_width) {
+	case 8:
+	case 16:
+		break;
+	default:
+		dev_err(dev, "unsupported MSG_CTL width: %d\n",
+			 bs->msg_ctl_width);
+		goto out_clk_disable;
+	}
+
 	/* Initialize hardware */
 	clk_enable(bs->clk);
 	bcm_spi_writeb(bs, SPI_INTR_CLEAR_ALL, SPI_INT_STATUS);
diff --git a/drivers/staging/ipack/devices/ipoctal.c b/drivers/staging/ipack/devices/ipoctal.c
index fd0e301..a68d981 100644
--- a/drivers/staging/ipack/devices/ipoctal.c
+++ b/drivers/staging/ipack/devices/ipoctal.c
@@ -502,7 +502,7 @@
 		ipoctal->pointer_read[i] = 0;
 		ipoctal->pointer_write[i] = 0;
 		ipoctal->nb_bytes[i] = 0;
-		tty_register_device(tty, i, NULL);
+		tty_port_register_device(&ipoctal->tty_port[i], tty, i, NULL);
 
 		/*
 		 * Enable again the RX. TX will be enabled when
@@ -617,7 +617,7 @@
 	struct ipoctal *ipoctal = tty->driver_data;
 	speed_t baud;
 
-	cflag = tty->termios->c_cflag;
+	cflag = tty->termios.c_cflag;
 
 	/* Disable and reset everything before change the setup */
 	ipoctal_write_io_reg(ipoctal, &ipoctal->chan_regs[channel].u.w.cr,
@@ -643,7 +643,7 @@
 	default:
 		mr1 |= MR1_CHRL_8_BITS;
 		/* By default, select CS8 */
-		tty->termios->c_cflag = (cflag & ~CSIZE) | CS8;
+		tty->termios.c_cflag = (cflag & ~CSIZE) | CS8;
 		break;
 	}
 
@@ -657,7 +657,7 @@
 		mr1 |= MR1_PARITY_OFF;
 
 	/* Mark or space parity is not supported */
-	tty->termios->c_cflag &= ~CMSPAR;
+	tty->termios.c_cflag &= ~CMSPAR;
 
 	/* Set stop bits */
 	if (cflag & CSTOPB)
@@ -690,10 +690,10 @@
 	}
 
 	baud = tty_get_baud_rate(tty);
-	tty_termios_encode_baud_rate(tty->termios, baud, baud);
+	tty_termios_encode_baud_rate(&tty->termios, baud, baud);
 
 	/* Set baud rate */
-	switch (tty->termios->c_ospeed) {
+	switch (baud) {
 	case 75:
 		csr |= TX_CLK_75 | RX_CLK_75;
 		break;
@@ -734,7 +734,7 @@
 	default:
 		csr |= TX_CLK_38400 | RX_CLK_38400;
 		/* In case of default, we establish 38400 bps */
-		tty_termios_encode_baud_rate(tty->termios, 38400, 38400);
+		tty_termios_encode_baud_rate(&tty->termios, 38400, 38400);
 		break;
 	}
 
diff --git a/drivers/staging/serqt_usb2/serqt_usb2.c b/drivers/staging/serqt_usb2/serqt_usb2.c
index 8a362f7..c90de96 100644
--- a/drivers/staging/serqt_usb2/serqt_usb2.c
+++ b/drivers/staging/serqt_usb2/serqt_usb2.c
@@ -315,10 +315,8 @@
 	}
 
 	tty = tty_port_tty_get(&port->port);
-	if (!tty) {
-		dbg("%s - bad tty pointer - exiting", __func__);
+	if (!tty)
 		return;
-	}
 
 	data = urb->transfer_buffer;
 
@@ -364,7 +362,7 @@
 		goto exit;
 	}
 
-	if (tty && RxCount) {
+	if (RxCount) {
 		flag_data = 0;
 		for (i = 0; i < RxCount; ++i) {
 			/* Look ahead code here */
@@ -428,7 +426,7 @@
 		dbg("%s - failed resubmitting read urb, error %d",
 		    __func__, result);
 	else {
-		if (tty && RxCount) {
+		if (RxCount) {
 			tty_flip_buffer_push(tty);
 			tty_schedule_flip(tty);
 		}
@@ -897,8 +895,6 @@
 	 * Put this here to make it responsive to stty and defaults set by
 	 * the tty layer
 	 */
-	/* FIXME: is this needed? */
-	/* qt_set_termios(tty, port, NULL); */
 
 	/*  Check to see if we've set up our endpoint info yet */
 	if (port0->open_ports == 1) {
@@ -1195,7 +1191,7 @@
 			   struct usb_serial_port *port,
 			   struct ktermios *old_termios)
 {
-	struct ktermios *termios = tty->termios;
+	struct ktermios *termios = &tty->termios;
 	unsigned char new_LCR = 0;
 	unsigned int cflag = termios->c_cflag;
 	unsigned int index;
@@ -1204,7 +1200,7 @@
 
 	index = tty->index - port->serial->minor;
 
-	switch (cflag) {
+	switch (cflag & CSIZE) {
 	case CS5:
 		new_LCR |= SERIAL_5_DATA;
 		break;
@@ -1215,6 +1211,8 @@
 		new_LCR |= SERIAL_7_DATA;
 		break;
 	default:
+		termios->c_cflag &= ~CSIZE;
+		termios->c_cflag |= CS8;
 	case CS8:
 		new_LCR |= SERIAL_8_DATA;
 		break;
@@ -1301,7 +1299,7 @@
 			dbg(__FILE__ "BoxSetSW_FlowCtrl (diabling) failed\n");
 
 	}
-	tty->termios->c_cflag &= ~CMSPAR;
+	termios->c_cflag &= ~CMSPAR;
 	/* FIXME: Error cases should be returning the actual bits changed only */
 }
 
diff --git a/drivers/staging/speakup/serialio.h b/drivers/staging/speakup/serialio.h
index 614271f..55d68b5 100644
--- a/drivers/staging/speakup/serialio.h
+++ b/drivers/staging/speakup/serialio.h
@@ -1,8 +1,7 @@
 #ifndef _SPEAKUP_SERIAL_H
 #define _SPEAKUP_SERIAL_H
 
-#include <linux/serial.h>	/* for rs_table, serial constants &
-				   serial_uart_config */
+#include <linux/serial.h>	/* for rs_table, serial constants */
 #include <linux/serial_reg.h>	/* for more serial constants */
 #ifndef __sparc__
 #include <asm/serial.h>
diff --git a/drivers/tty/amiserial.c b/drivers/tty/amiserial.c
index 6cc4358..42d0a25 100644
--- a/drivers/tty/amiserial.c
+++ b/drivers/tty/amiserial.c
@@ -420,7 +420,7 @@
 				tty_hangup(port->tty);
 		}
 	}
-	if (port->flags & ASYNC_CTS_FLOW) {
+	if (tty_port_cts_enabled(port)) {
 		if (port->tty->hw_stopped) {
 			if (!(status & SER_CTS)) {
 #if (defined(SERIAL_DEBUG_INTR) || defined(SERIAL_DEBUG_FLOW))
@@ -646,7 +646,7 @@
 	custom.adkcon = AC_UARTBRK;
 	mb();
 
-	if (tty->termios->c_cflag & HUPCL)
+	if (tty->termios.c_cflag & HUPCL)
 		info->MCR &= ~(SER_DTR|SER_RTS);
 	rtsdtr_ctrl(info->MCR);
 
@@ -670,7 +670,7 @@
 	int	bits;
 	unsigned long	flags;
 
-	cflag = tty->termios->c_cflag;
+	cflag = tty->termios.c_cflag;
 
 	/* Byte size is always 8 bits plus parity bit if requested */
 
@@ -707,8 +707,8 @@
 	/* If the quotient is zero refuse the change */
 	if (!quot && old_termios) {
 		/* FIXME: Will need updating for new tty in the end */
-		tty->termios->c_cflag &= ~CBAUD;
-		tty->termios->c_cflag |= (old_termios->c_cflag & CBAUD);
+		tty->termios.c_cflag &= ~CBAUD;
+		tty->termios.c_cflag |= (old_termios->c_cflag & CBAUD);
 		baud = tty_get_baud_rate(tty);
 		if (!baud)
 			baud = 9600;
@@ -984,7 +984,7 @@
 	if (I_IXOFF(tty))
 		rs_send_xchar(tty, STOP_CHAR(tty));
 
-	if (tty->termios->c_cflag & CRTSCTS)
+	if (tty->termios.c_cflag & CRTSCTS)
 		info->MCR &= ~SER_RTS;
 
 	local_irq_save(flags);
@@ -1012,7 +1012,7 @@
 		else
 			rs_send_xchar(tty, START_CHAR(tty));
 	}
-	if (tty->termios->c_cflag & CRTSCTS)
+	if (tty->termios.c_cflag & CRTSCTS)
 		info->MCR |= SER_RTS;
 	local_irq_save(flags);
 	rtsdtr_ctrl(info->MCR);
@@ -1033,7 +1033,7 @@
 	if (!retinfo)
 		return -EFAULT;
 	memset(&tmp, 0, sizeof(tmp));
-	tty_lock();
+	tty_lock(tty);
 	tmp.line = tty->index;
 	tmp.port = state->port;
 	tmp.flags = state->tport.flags;
@@ -1042,7 +1042,7 @@
 	tmp.close_delay = state->tport.close_delay;
 	tmp.closing_wait = state->tport.closing_wait;
 	tmp.custom_divisor = state->custom_divisor;
-	tty_unlock();
+	tty_unlock(tty);
 	if (copy_to_user(retinfo,&tmp,sizeof(*retinfo)))
 		return -EFAULT;
 	return 0;
@@ -1059,12 +1059,12 @@
 	if (copy_from_user(&new_serial,new_info,sizeof(new_serial)))
 		return -EFAULT;
 
-	tty_lock();
+	tty_lock(tty);
 	change_spd = ((new_serial.flags ^ port->flags) & ASYNC_SPD_MASK) ||
 		new_serial.custom_divisor != state->custom_divisor;
 	if (new_serial.irq || new_serial.port != state->port ||
 			new_serial.xmit_fifo_size != state->xmit_fifo_size) {
-		tty_unlock();
+		tty_unlock(tty);
 		return -EINVAL;
 	}
   
@@ -1074,7 +1074,7 @@
 		    (new_serial.xmit_fifo_size != state->xmit_fifo_size) ||
 		    ((new_serial.flags & ~ASYNC_USR_MASK) !=
 		     (port->flags & ~ASYNC_USR_MASK))) {
-			tty_unlock();
+			tty_unlock(tty);
 			return -EPERM;
 		}
 		port->flags = ((port->flags & ~ASYNC_USR_MASK) |
@@ -1084,7 +1084,7 @@
 	}
 
 	if (new_serial.baud_base < 9600) {
-		tty_unlock();
+		tty_unlock(tty);
 		return -EINVAL;
 	}
 
@@ -1116,7 +1116,7 @@
 		}
 	} else
 		retval = startup(tty, state);
-	tty_unlock();
+	tty_unlock(tty);
 	return retval;
 }
 
@@ -1330,7 +1330,7 @@
 {
 	struct serial_state *info = tty->driver_data;
 	unsigned long flags;
-	unsigned int cflag = tty->termios->c_cflag;
+	unsigned int cflag = tty->termios.c_cflag;
 
 	change_speed(tty, info, old_termios);
 
@@ -1347,7 +1347,7 @@
 	if (!(old_termios->c_cflag & CBAUD) &&
 	    (cflag & CBAUD)) {
 		info->MCR |= SER_DTR;
-		if (!(tty->termios->c_cflag & CRTSCTS) || 
+		if (!(tty->termios.c_cflag & CRTSCTS) || 
 		    !test_bit(TTY_THROTTLED, &tty->flags)) {
 			info->MCR |= SER_RTS;
 		}
@@ -1358,7 +1358,7 @@
 
 	/* Handle turning off CRTSCTS */
 	if ((old_termios->c_cflag & CRTSCTS) &&
-	    !(tty->termios->c_cflag & CRTSCTS)) {
+	    !(tty->termios.c_cflag & CRTSCTS)) {
 		tty->hw_stopped = 0;
 		rs_start(tty);
 	}
@@ -1371,7 +1371,7 @@
 	 * or not.  Hence, this may change.....
 	 */
 	if (!(old_termios->c_cflag & CLOCAL) &&
-	    (tty->termios->c_cflag & CLOCAL))
+	    (tty->termios.c_cflag & CLOCAL))
 		wake_up_interruptible(&info->open_wait);
 #endif
 }
@@ -1710,10 +1710,6 @@
 	serial_driver->flags = TTY_DRIVER_REAL_RAW;
 	tty_set_operations(serial_driver, &serial_ops);
 
-	error = tty_register_driver(serial_driver);
-	if (error)
-		goto fail_put_tty_driver;
-
 	state = rs_table;
 	state->port = (int)&custom.serdatr; /* Just to give it a value */
 	state->custom_divisor = 0;
@@ -1724,6 +1720,11 @@
 	state->icount.overrun = state->icount.brk = 0;
 	tty_port_init(&state->tport);
 	state->tport.ops = &amiga_port_ops;
+	tty_port_link_device(&state->tport, serial_driver, 0);
+
+	error = tty_register_driver(serial_driver);
+	if (error)
+		goto fail_put_tty_driver;
 
 	printk(KERN_INFO "ttyS0 is the amiga builtin serial port\n");
 
diff --git a/drivers/tty/bfin_jtag_comm.c b/drivers/tty/bfin_jtag_comm.c
index 61fc74f..02b7d3a 100644
--- a/drivers/tty/bfin_jtag_comm.c
+++ b/drivers/tty/bfin_jtag_comm.c
@@ -263,6 +263,7 @@
 	bfin_jc_driver->subtype      = SERIAL_TYPE_NORMAL;
 	bfin_jc_driver->init_termios = tty_std_termios;
 	tty_set_operations(bfin_jc_driver, &bfin_jc_ops);
+	tty_port_link_device(&port, bfin_jc_driver, 0);
 
 	ret = tty_register_driver(bfin_jc_driver);
 	if (ret)
diff --git a/drivers/tty/cyclades.c b/drivers/tty/cyclades.c
index e61cabd..0a6a0bc 100644
--- a/drivers/tty/cyclades.c
+++ b/drivers/tty/cyclades.c
@@ -727,7 +727,7 @@
 		else
 			tty_hangup(tty);
 	}
-	if ((mdm_change & CyCTS) && (info->port.flags & ASYNC_CTS_FLOW)) {
+	if ((mdm_change & CyCTS) && tty_port_cts_enabled(&info->port)) {
 		if (tty->hw_stopped) {
 			if (mdm_status & CyCTS) {
 				/* cy_start isn't used
@@ -1459,7 +1459,7 @@
 			info->port.xmit_buf = NULL;
 			free_page((unsigned long)temp);
 		}
-		if (tty->termios->c_cflag & HUPCL)
+		if (tty->termios.c_cflag & HUPCL)
 			cyy_change_rts_dtr(info, 0, TIOCM_RTS | TIOCM_DTR);
 
 		cyy_issue_cmd(info, CyCHAN_CTL | CyDIS_RCVR);
@@ -1488,7 +1488,7 @@
 			free_page((unsigned long)temp);
 		}
 
-		if (tty->termios->c_cflag & HUPCL)
+		if (tty->termios.c_cflag & HUPCL)
 			tty_port_lower_dtr_rts(&info->port);
 
 		set_bit(TTY_IO_ERROR, &tty->flags);
@@ -1599,7 +1599,7 @@
 	 * If the port is the middle of closing, bail out now
 	 */
 	if (tty_hung_up_p(filp) || (info->port.flags & ASYNC_CLOSING)) {
-		wait_event_interruptible_tty(info->port.close_wait,
+		wait_event_interruptible_tty(tty, info->port.close_wait,
 				!(info->port.flags & ASYNC_CLOSING));
 		return (info->port.flags & ASYNC_HUP_NOTIFY) ? -EAGAIN: -ERESTARTSYS;
 	}
@@ -1999,14 +1999,11 @@
 	int baud, baud_rate = 0;
 	int i;
 
-	if (!tty->termios) /* XXX can this happen at all? */
-		return;
-
 	if (info->line == -1)
 		return;
 
-	cflag = tty->termios->c_cflag;
-	iflag = tty->termios->c_iflag;
+	cflag = tty->termios.c_cflag;
+	iflag = tty->termios.c_iflag;
 
 	/*
 	 * Set up the tty->alt_speed kludge
@@ -2825,7 +2822,7 @@
 	cy_set_line_char(info, tty);
 
 	if ((old_termios->c_cflag & CRTSCTS) &&
-			!(tty->termios->c_cflag & CRTSCTS)) {
+			!(tty->termios.c_cflag & CRTSCTS)) {
 		tty->hw_stopped = 0;
 		cy_start(tty);
 	}
@@ -2837,7 +2834,7 @@
 	 * or not.  Hence, this may change.....
 	 */
 	if (!(old_termios->c_cflag & CLOCAL) &&
-	    (tty->termios->c_cflag & CLOCAL))
+	    (tty->termios.c_cflag & CLOCAL))
 		wake_up_interruptible(&info->port.open_wait);
 #endif
 }				/* cy_set_termios */
@@ -2899,7 +2896,7 @@
 			info->throttle = 1;
 	}
 
-	if (tty->termios->c_cflag & CRTSCTS) {
+	if (tty->termios.c_cflag & CRTSCTS) {
 		if (!cy_is_Z(card)) {
 			spin_lock_irqsave(&card->card_lock, flags);
 			cyy_change_rts_dtr(info, 0, TIOCM_RTS);
@@ -2938,7 +2935,7 @@
 			cy_send_xchar(tty, START_CHAR(tty));
 	}
 
-	if (tty->termios->c_cflag & CRTSCTS) {
+	if (tty->termios.c_cflag & CRTSCTS) {
 		card = info->card;
 		if (!cy_is_Z(card)) {
 			spin_lock_irqsave(&card->card_lock, flags);
@@ -3289,9 +3286,10 @@
 static int __init cy_detect_isa(void)
 {
 #ifdef CONFIG_ISA
+	struct cyclades_card *card;
 	unsigned short cy_isa_irq, nboard;
 	void __iomem *cy_isa_address;
-	unsigned short i, j, cy_isa_nchan;
+	unsigned short i, j, k, cy_isa_nchan;
 	int isparam = 0;
 
 	nboard = 0;
@@ -3349,7 +3347,8 @@
 		}
 		/* fill the next cy_card structure available */
 		for (j = 0; j < NR_CARDS; j++) {
-			if (cy_card[j].base_addr == NULL)
+			card = &cy_card[j];
+			if (card->base_addr == NULL)
 				break;
 		}
 		if (j == NR_CARDS) {	/* no more cy_cards available */
@@ -3363,7 +3362,7 @@
 
 		/* allocate IRQ */
 		if (request_irq(cy_isa_irq, cyy_interrupt,
-				0, "Cyclom-Y", &cy_card[j])) {
+				0, "Cyclom-Y", card)) {
 			printk(KERN_ERR "Cyclom-Y/ISA found at 0x%lx, but "
 				"could not allocate IRQ#%d.\n",
 				(unsigned long)cy_isa_address, cy_isa_irq);
@@ -3372,16 +3371,16 @@
 		}
 
 		/* set cy_card */
-		cy_card[j].base_addr = cy_isa_address;
-		cy_card[j].ctl_addr.p9050 = NULL;
-		cy_card[j].irq = (int)cy_isa_irq;
-		cy_card[j].bus_index = 0;
-		cy_card[j].first_line = cy_next_channel;
-		cy_card[j].num_chips = cy_isa_nchan / CyPORTS_PER_CHIP;
-		cy_card[j].nports = cy_isa_nchan;
-		if (cy_init_card(&cy_card[j])) {
-			cy_card[j].base_addr = NULL;
-			free_irq(cy_isa_irq, &cy_card[j]);
+		card->base_addr = cy_isa_address;
+		card->ctl_addr.p9050 = NULL;
+		card->irq = (int)cy_isa_irq;
+		card->bus_index = 0;
+		card->first_line = cy_next_channel;
+		card->num_chips = cy_isa_nchan / CyPORTS_PER_CHIP;
+		card->nports = cy_isa_nchan;
+		if (cy_init_card(card)) {
+			card->base_addr = NULL;
+			free_irq(cy_isa_irq, card);
 			iounmap(cy_isa_address);
 			continue;
 		}
@@ -3393,9 +3392,10 @@
 			(unsigned long)(cy_isa_address + (CyISA_Ywin - 1)),
 			cy_isa_irq, cy_isa_nchan, cy_next_channel);
 
-		for (j = cy_next_channel;
-				j < cy_next_channel + cy_isa_nchan; j++)
-			tty_register_device(cy_serial_driver, j, NULL);
+		for (k = 0, j = cy_next_channel;
+				j < cy_next_channel + cy_isa_nchan; j++, k++)
+			tty_port_register_device(&card->ports[k].port,
+					cy_serial_driver, j, NULL);
 		cy_next_channel += cy_isa_nchan;
 	}
 	return nboard;
@@ -3695,10 +3695,11 @@
 static int __devinit cy_pci_probe(struct pci_dev *pdev,
 		const struct pci_device_id *ent)
 {
+	struct cyclades_card *card;
 	void __iomem *addr0 = NULL, *addr2 = NULL;
 	char *card_name = NULL;
 	u32 uninitialized_var(mailbox);
-	unsigned int device_id, nchan = 0, card_no, i;
+	unsigned int device_id, nchan = 0, card_no, i, j;
 	unsigned char plx_ver;
 	int retval, irq;
 
@@ -3829,7 +3830,8 @@
 	}
 	/* fill the next cy_card structure available */
 	for (card_no = 0; card_no < NR_CARDS; card_no++) {
-		if (cy_card[card_no].base_addr == NULL)
+		card = &cy_card[card_no];
+		if (card->base_addr == NULL)
 			break;
 	}
 	if (card_no == NR_CARDS) {	/* no more cy_cards available */
@@ -3843,27 +3845,26 @@
 			device_id == PCI_DEVICE_ID_CYCLOM_Y_Hi) {
 		/* allocate IRQ */
 		retval = request_irq(irq, cyy_interrupt,
-				IRQF_SHARED, "Cyclom-Y", &cy_card[card_no]);
+				IRQF_SHARED, "Cyclom-Y", card);
 		if (retval) {
 			dev_err(&pdev->dev, "could not allocate IRQ\n");
 			goto err_unmap;
 		}
-		cy_card[card_no].num_chips = nchan / CyPORTS_PER_CHIP;
+		card->num_chips = nchan / CyPORTS_PER_CHIP;
 	} else {
 		struct FIRM_ID __iomem *firm_id = addr2 + ID_ADDRESS;
 		struct ZFW_CTRL __iomem *zfw_ctrl;
 
 		zfw_ctrl = addr2 + (readl(&firm_id->zfwctrl_addr) & 0xfffff);
 
-		cy_card[card_no].hw_ver = mailbox;
-		cy_card[card_no].num_chips = (unsigned int)-1;
-		cy_card[card_no].board_ctrl = &zfw_ctrl->board_ctrl;
+		card->hw_ver = mailbox;
+		card->num_chips = (unsigned int)-1;
+		card->board_ctrl = &zfw_ctrl->board_ctrl;
 #ifdef CONFIG_CYZ_INTR
 		/* allocate IRQ only if board has an IRQ */
 		if (irq != 0 && irq != 255) {
 			retval = request_irq(irq, cyz_interrupt,
-					IRQF_SHARED, "Cyclades-Z",
-					&cy_card[card_no]);
+					IRQF_SHARED, "Cyclades-Z", card);
 			if (retval) {
 				dev_err(&pdev->dev, "could not allocate IRQ\n");
 				goto err_unmap;
@@ -3873,17 +3874,17 @@
 	}
 
 	/* set cy_card */
-	cy_card[card_no].base_addr = addr2;
-	cy_card[card_no].ctl_addr.p9050 = addr0;
-	cy_card[card_no].irq = irq;
-	cy_card[card_no].bus_index = 1;
-	cy_card[card_no].first_line = cy_next_channel;
-	cy_card[card_no].nports = nchan;
-	retval = cy_init_card(&cy_card[card_no]);
+	card->base_addr = addr2;
+	card->ctl_addr.p9050 = addr0;
+	card->irq = irq;
+	card->bus_index = 1;
+	card->first_line = cy_next_channel;
+	card->nports = nchan;
+	retval = cy_init_card(card);
 	if (retval)
 		goto err_null;
 
-	pci_set_drvdata(pdev, &cy_card[card_no]);
+	pci_set_drvdata(pdev, card);
 
 	if (device_id == PCI_DEVICE_ID_CYCLOM_Y_Lo ||
 			device_id == PCI_DEVICE_ID_CYCLOM_Y_Hi) {
@@ -3909,14 +3910,15 @@
 
 	dev_info(&pdev->dev, "%s/PCI #%d found: %d channels starting from "
 		"port %d.\n", card_name, card_no + 1, nchan, cy_next_channel);
-	for (i = cy_next_channel; i < cy_next_channel + nchan; i++)
-		tty_register_device(cy_serial_driver, i, &pdev->dev);
+	for (j = 0, i = cy_next_channel; i < cy_next_channel + nchan; i++, j++)
+		tty_port_register_device(&card->ports[j].port,
+				cy_serial_driver, i, &pdev->dev);
 	cy_next_channel += nchan;
 
 	return 0;
 err_null:
-	cy_card[card_no].base_addr = NULL;
-	free_irq(irq, &cy_card[card_no]);
+	card->base_addr = NULL;
+	free_irq(irq, card);
 err_unmap:
 	iounmap(addr0);
 	if (addr2)
diff --git a/drivers/tty/ehv_bytechan.c b/drivers/tty/ehv_bytechan.c
index 4813684..4ab936b 100644
--- a/drivers/tty/ehv_bytechan.c
+++ b/drivers/tty/ehv_bytechan.c
@@ -738,16 +738,17 @@
 		goto error;
 	}
 
-	bc->dev = tty_register_device(ehv_bc_driver, i, &pdev->dev);
+	tty_port_init(&bc->port);
+	bc->port.ops = &ehv_bc_tty_port_ops;
+
+	bc->dev = tty_port_register_device(&bc->port, ehv_bc_driver, i,
+			&pdev->dev);
 	if (IS_ERR(bc->dev)) {
 		ret = PTR_ERR(bc->dev);
 		dev_err(&pdev->dev, "could not register tty (ret=%i)\n", ret);
 		goto error;
 	}
 
-	tty_port_init(&bc->port);
-	bc->port.ops = &ehv_bc_tty_port_ops;
-
 	dev_set_drvdata(&pdev->dev, bc);
 
 	dev_info(&pdev->dev, "registered /dev/%s%u for byte channel %u\n",
diff --git a/drivers/tty/hvc/hvc_console.c b/drivers/tty/hvc/hvc_console.c
index 2d691eb..7f80f15 100644
--- a/drivers/tty/hvc/hvc_console.c
+++ b/drivers/tty/hvc/hvc_console.c
@@ -299,20 +299,33 @@
 	hvc_kick();
 }
 
+static int hvc_install(struct tty_driver *driver, struct tty_struct *tty)
+{
+	struct hvc_struct *hp;
+	int rc;
+
+	/* Auto increments kref reference if found. */
+	if (!(hp = hvc_get_by_index(tty->index)))
+		return -ENODEV;
+
+	tty->driver_data = hp;
+
+	rc = tty_port_install(&hp->port, driver, tty);
+	if (rc)
+		tty_port_put(&hp->port);
+	return rc;
+}
+
 /*
  * The TTY interface won't be used until after the vio layer has exposed the vty
  * adapter to the kernel.
  */
 static int hvc_open(struct tty_struct *tty, struct file * filp)
 {
-	struct hvc_struct *hp;
+	struct hvc_struct *hp = tty->driver_data;
 	unsigned long flags;
 	int rc = 0;
 
-	/* Auto increments kref reference if found. */
-	if (!(hp = hvc_get_by_index(tty->index)))
-		return -ENODEV;
-
 	spin_lock_irqsave(&hp->port.lock, flags);
 	/* Check and then increment for fast path open. */
 	if (hp->port.count++ > 0) {
@@ -322,7 +335,6 @@
 	} /* else count == 0 */
 	spin_unlock_irqrestore(&hp->port.lock, flags);
 
-	tty->driver_data = hp;
 	tty_port_tty_set(&hp->port, tty);
 
 	if (hp->ops->notifier_add)
@@ -389,6 +401,11 @@
 				hp->vtermno, hp->port.count);
 		spin_unlock_irqrestore(&hp->port.lock, flags);
 	}
+}
+
+static void hvc_cleanup(struct tty_struct *tty)
+{
+	struct hvc_struct *hp = tty->driver_data;
 
 	tty_port_put(&hp->port);
 }
@@ -792,8 +809,10 @@
 #endif
 
 static const struct tty_operations hvc_ops = {
+	.install = hvc_install,
 	.open = hvc_open,
 	.close = hvc_close,
+	.cleanup = hvc_cleanup,
 	.write = hvc_write,
 	.hangup = hvc_hangup,
 	.unthrottle = hvc_unthrottle,
diff --git a/drivers/tty/hvc/hvcs.c b/drivers/tty/hvc/hvcs.c
index d56788c..cab5c7a 100644
--- a/drivers/tty/hvc/hvcs.c
+++ b/drivers/tty/hvc/hvcs.c
@@ -1102,27 +1102,20 @@
 	return NULL;
 }
 
-/*
- * This is invoked via the tty_open interface when a user app connects to the
- * /dev node.
- */
-static int hvcs_open(struct tty_struct *tty, struct file *filp)
+static int hvcs_install(struct tty_driver *driver, struct tty_struct *tty)
 {
 	struct hvcs_struct *hvcsd;
-	int rc, retval = 0;
-	unsigned long flags;
-	unsigned int irq;
 	struct vio_dev *vdev;
-	unsigned long unit_address;
-
-	if (tty->driver_data)
-		goto fast_open;
+	unsigned long unit_address, flags;
+	unsigned int irq;
+	int retval;
 
 	/*
 	 * Is there a vty-server that shares the same index?
 	 * This function increments the kref index.
 	 */
-	if (!(hvcsd = hvcs_get_by_index(tty->index))) {
+	hvcsd = hvcs_get_by_index(tty->index);
+	if (!hvcsd) {
 		printk(KERN_WARNING "HVCS: open failed, no device associated"
 				" with tty->index %d.\n", tty->index);
 		return -ENODEV;
@@ -1130,11 +1123,16 @@
 
 	spin_lock_irqsave(&hvcsd->lock, flags);
 
-	if (hvcsd->connected == 0)
-		if ((retval = hvcs_partner_connect(hvcsd)))
-			goto error_release;
+	if (hvcsd->connected == 0) {
+		retval = hvcs_partner_connect(hvcsd);
+		if (retval) {
+			spin_unlock_irqrestore(&hvcsd->lock, flags);
+			printk(KERN_WARNING "HVCS: partner connect failed.\n");
+			goto err_put;
+		}
+	}
 
-	hvcsd->port.count = 1;
+	hvcsd->port.count = 0;
 	hvcsd->port.tty = tty;
 	tty->driver_data = hvcsd;
 
@@ -1155,37 +1153,48 @@
 	 * This must be done outside of the spinlock because it requests irqs
 	 * and will grab the spinlock and free the connection if it fails.
 	 */
-	if (((rc = hvcs_enable_device(hvcsd, unit_address, irq, vdev)))) {
-		tty_port_put(&hvcsd->port);
+	retval = hvcs_enable_device(hvcsd, unit_address, irq, vdev);
+	if (retval) {
 		printk(KERN_WARNING "HVCS: enable device failed.\n");
-		return rc;
+		goto err_put;
 	}
 
-	goto open_success;
+	retval = tty_port_install(&hvcsd->port, driver, tty);
+	if (retval)
+		goto err_irq;
 
-fast_open:
-	hvcsd = tty->driver_data;
+	return 0;
+err_irq:
+	spin_lock_irqsave(&hvcsd->lock, flags);
+	vio_disable_interrupts(hvcsd->vdev);
+	spin_unlock_irqrestore(&hvcsd->lock, flags);
+	free_irq(irq, hvcsd);
+err_put:
+	tty_port_put(&hvcsd->port);
+
+	return retval;
+}
+
+/*
+ * This is invoked via the tty_open interface when a user app connects to the
+ * /dev node.
+ */
+static int hvcs_open(struct tty_struct *tty, struct file *filp)
+{
+	struct hvcs_struct *hvcsd = tty->driver_data;
+	unsigned long flags;
 
 	spin_lock_irqsave(&hvcsd->lock, flags);
-	tty_port_get(&hvcsd->port);
 	hvcsd->port.count++;
 	hvcsd->todo_mask |= HVCS_SCHED_READ;
 	spin_unlock_irqrestore(&hvcsd->lock, flags);
 
-open_success:
 	hvcs_kick();
 
 	printk(KERN_INFO "HVCS: vty-server@%X connection opened.\n",
 		hvcsd->vdev->unit_address );
 
 	return 0;
-
-error_release:
-	spin_unlock_irqrestore(&hvcsd->lock, flags);
-	tty_port_put(&hvcsd->port);
-
-	printk(KERN_WARNING "HVCS: partner connect failed.\n");
-	return retval;
 }
 
 static void hvcs_close(struct tty_struct *tty, struct file *filp)
@@ -1236,7 +1245,6 @@
 		tty->driver_data = NULL;
 
 		free_irq(irq, hvcsd);
-		tty_port_put(&hvcsd->port);
 		return;
 	} else if (hvcsd->port.count < 0) {
 		printk(KERN_ERR "HVCS: vty-server@%X open_count: %d"
@@ -1245,6 +1253,12 @@
 	}
 
 	spin_unlock_irqrestore(&hvcsd->lock, flags);
+}
+
+static void hvcs_cleanup(struct tty_struct * tty)
+{
+	struct hvcs_struct *hvcsd = tty->driver_data;
+
 	tty_port_put(&hvcsd->port);
 }
 
@@ -1431,8 +1445,10 @@
 }
 
 static const struct tty_operations hvcs_ops = {
+	.install = hvcs_install,
 	.open = hvcs_open,
 	.close = hvcs_close,
+	.cleanup = hvcs_cleanup,
 	.hangup = hvcs_hangup,
 	.write = hvcs_write,
 	.write_room = hvcs_write_room,
diff --git a/drivers/tty/hvc/hvsi.c b/drivers/tty/hvc/hvsi.c
index 6f5bc49..0083bc1 100644
--- a/drivers/tty/hvc/hvsi.c
+++ b/drivers/tty/hvc/hvsi.c
@@ -1080,6 +1080,8 @@
 		struct hvsi_struct *hp = &hvsi_ports[i];
 		int ret = 1;
 
+		tty_port_link_device(&hp->port, hvsi_driver, i);
+
 		ret = request_irq(hp->virq, hvsi_interrupt, 0, "hvsi", hp);
 		if (ret)
 			printk(KERN_ERR "HVSI: couldn't reserve irq 0x%x (error %i)\n",
diff --git a/drivers/tty/hvc/hvsi_lib.c b/drivers/tty/hvc/hvsi_lib.c
index 59c135d..3396eb9 100644
--- a/drivers/tty/hvc/hvsi_lib.c
+++ b/drivers/tty/hvc/hvsi_lib.c
@@ -400,7 +400,7 @@
 		spin_unlock_irqrestore(&hp->lock, flags);
 
 		/* Clear our own DTR */
-		if (!pv->tty || (pv->tty->termios->c_cflag & HUPCL))
+		if (!pv->tty || (pv->tty->termios.c_cflag & HUPCL))
 			hvsilib_write_mctrl(pv, 0);
 
 		/* Tear down the connection */
diff --git a/drivers/tty/ipwireless/tty.c b/drivers/tty/ipwireless/tty.c
index f8b5fa0..160f0ad 100644
--- a/drivers/tty/ipwireless/tty.c
+++ b/drivers/tty/ipwireless/tty.c
@@ -476,7 +476,7 @@
 	mutex_init(&ttys[j]->ipw_tty_mutex);
 	tty_port_init(&ttys[j]->port);
 
-	tty_register_device(ipw_tty_driver, j, NULL);
+	tty_port_register_device(&ttys[j]->port, ipw_tty_driver, j, NULL);
 	ipwireless_associate_network_tty(network, channel_idx, ttys[j]);
 
 	if (secondary_channel_idx != -1)
diff --git a/drivers/tty/isicom.c b/drivers/tty/isicom.c
index e1235ac..d7492e1 100644
--- a/drivers/tty/isicom.c
+++ b/drivers/tty/isicom.c
@@ -600,7 +600,7 @@
 					port->status &= ~ISI_DCD;
 			}
 
-			if (port->port.flags & ASYNC_CTS_FLOW) {
+			if (tty_port_cts_enabled(&port->port)) {
 				if (tty->hw_stopped) {
 					if (header & ISI_CTS) {
 						port->port.tty->hw_stopped = 0;
@@ -702,7 +702,7 @@
 
 		/* 1,2,3,4 => 57.6, 115.2, 230, 460 kbps resp. */
 		if (baud < 1 || baud > 4)
-			tty->termios->c_cflag &= ~CBAUDEX;
+			tty->termios.c_cflag &= ~CBAUDEX;
 		else
 			baud += 15;
 	}
@@ -1196,8 +1196,8 @@
 	if (isicom_paranoia_check(port, tty->name, "isicom_set_termios"))
 		return;
 
-	if (tty->termios->c_cflag == old_termios->c_cflag &&
-			tty->termios->c_iflag == old_termios->c_iflag)
+	if (tty->termios.c_cflag == old_termios->c_cflag &&
+			tty->termios.c_iflag == old_termios->c_iflag)
 		return;
 
 	spin_lock_irqsave(&port->card->card_lock, flags);
@@ -1205,7 +1205,7 @@
 	spin_unlock_irqrestore(&port->card->card_lock, flags);
 
 	if ((old_termios->c_cflag & CRTSCTS) &&
-			!(tty->termios->c_cflag & CRTSCTS)) {
+			!(tty->termios.c_cflag & CRTSCTS)) {
 		tty->hw_stopped = 0;
 		isicom_start(tty);
 	}
@@ -1611,7 +1611,8 @@
 		goto errunri;
 
 	for (index = 0; index < board->port_count; index++)
-		tty_register_device(isicom_normal, board->index * 16 + index,
+		tty_port_register_device(&board->ports[index].port,
+				isicom_normal, board->index * 16 + index,
 				&pdev->dev);
 
 	return 0;
diff --git a/drivers/tty/moxa.c b/drivers/tty/moxa.c
index 324467d..56e616b 100644
--- a/drivers/tty/moxa.c
+++ b/drivers/tty/moxa.c
@@ -169,6 +169,7 @@
 static unsigned long baseaddr[MAX_BOARDS];
 static unsigned int type[MAX_BOARDS];
 static unsigned int numports[MAX_BOARDS];
+static struct tty_port moxa_service_port;
 
 MODULE_AUTHOR("William Chen");
 MODULE_DESCRIPTION("MOXA Intellio Family Multiport Board Device Driver");
@@ -367,10 +368,10 @@
 					tmp.dcd = 1;
 
 				ttyp = tty_port_tty_get(&p->port);
-				if (!ttyp || !ttyp->termios)
+				if (!ttyp)
 					tmp.cflag = p->cflag;
 				else
-					tmp.cflag = ttyp->termios->c_cflag;
+					tmp.cflag = ttyp->termios.c_cflag;
 				tty_kref_put(ttyp);
 copy:
 				if (copy_to_user(argm, &tmp, sizeof(tmp)))
@@ -834,7 +835,7 @@
 	const struct firmware *fw;
 	const char *file;
 	struct moxa_port *p;
-	unsigned int i;
+	unsigned int i, first_idx;
 	int ret;
 
 	brd->ports = kcalloc(MAX_PORTS_PER_BOARD, sizeof(*brd->ports),
@@ -887,6 +888,11 @@
 		mod_timer(&moxaTimer, jiffies + HZ / 50);
 	spin_unlock_bh(&moxa_lock);
 
+	first_idx = (brd - moxa_boards) * MAX_PORTS_PER_BOARD;
+	for (i = 0; i < brd->numPorts; i++)
+		tty_port_register_device(&brd->ports[i].port, moxaDriver,
+				first_idx + i, dev);
+
 	return 0;
 err_free:
 	kfree(brd->ports);
@@ -896,7 +902,7 @@
 
 static void moxa_board_deinit(struct moxa_board_conf *brd)
 {
-	unsigned int a, opened;
+	unsigned int a, opened, first_idx;
 
 	mutex_lock(&moxa_openlock);
 	spin_lock_bh(&moxa_lock);
@@ -925,6 +931,10 @@
 		mutex_lock(&moxa_openlock);
 	}
 
+	first_idx = (brd - moxa_boards) * MAX_PORTS_PER_BOARD;
+	for (a = 0; a < brd->numPorts; a++)
+		tty_unregister_device(moxaDriver, first_idx + a);
+
 	iounmap(brd->basemem);
 	brd->basemem = NULL;
 	kfree(brd->ports);
@@ -967,6 +977,7 @@
 	board->basemem = ioremap_nocache(pci_resource_start(pdev, 2), 0x4000);
 	if (board->basemem == NULL) {
 		dev_err(&pdev->dev, "can't remap io space 2\n");
+		retval = -ENOMEM;
 		goto err_reg;
 	}
 
@@ -1031,9 +1042,14 @@
 
 	printk(KERN_INFO "MOXA Intellio family driver version %s\n",
 			MOXA_VERSION);
-	moxaDriver = alloc_tty_driver(MAX_PORTS + 1);
-	if (!moxaDriver)
-		return -ENOMEM;
+
+	tty_port_init(&moxa_service_port);
+
+	moxaDriver = tty_alloc_driver(MAX_PORTS + 1,
+			TTY_DRIVER_REAL_RAW |
+			TTY_DRIVER_DYNAMIC_DEV);
+	if (IS_ERR(moxaDriver))
+		return PTR_ERR(moxaDriver);
 
 	moxaDriver->name = "ttyMX";
 	moxaDriver->major = ttymajor;
@@ -1044,8 +1060,9 @@
 	moxaDriver->init_termios.c_cflag = B9600 | CS8 | CREAD | CLOCAL | HUPCL;
 	moxaDriver->init_termios.c_ispeed = 9600;
 	moxaDriver->init_termios.c_ospeed = 9600;
-	moxaDriver->flags = TTY_DRIVER_REAL_RAW;
 	tty_set_operations(moxaDriver, &moxa_ops);
+	/* Having one more port only for ioctls is ugly */
+	tty_port_link_device(&moxa_service_port, moxaDriver, MAX_PORTS);
 
 	if (tty_register_driver(moxaDriver)) {
 		printk(KERN_ERR "can't register MOXA Smartio tty driver!\n");
@@ -1178,7 +1195,7 @@
 	mutex_lock(&ch->port.mutex);
 	if (!(ch->port.flags & ASYNC_INITIALIZED)) {
 		ch->statusflags = 0;
-		moxa_set_tty_param(tty, tty->termios);
+		moxa_set_tty_param(tty, &tty->termios);
 		MoxaPortLineCtrl(ch, 1, 1);
 		MoxaPortEnable(ch);
 		MoxaSetFifo(ch, ch->type == PORT_16550A);
@@ -1193,7 +1210,7 @@
 static void moxa_close(struct tty_struct *tty, struct file *filp)
 {
 	struct moxa_port *ch = tty->driver_data;
-	ch->cflag = tty->termios->c_cflag;
+	ch->cflag = tty->termios.c_cflag;
 	tty_port_close(&ch->port, tty, filp);
 }
 
@@ -1464,7 +1481,7 @@
 
 static void moxa_set_tty_param(struct tty_struct *tty, struct ktermios *old_termios)
 {
-	register struct ktermios *ts = tty->termios;
+	register struct ktermios *ts = &tty->termios;
 	struct moxa_port *ch = tty->driver_data;
 	int rts, cts, txflow, rxflow, xany, baud;
 
diff --git a/drivers/tty/mxser.c b/drivers/tty/mxser.c
index 90cc680..cfda47d 100644
--- a/drivers/tty/mxser.c
+++ b/drivers/tty/mxser.c
@@ -643,7 +643,7 @@
 	int ret = 0;
 	unsigned char status;
 
-	cflag = tty->termios->c_cflag;
+	cflag = tty->termios.c_cflag;
 	if (!info->ioaddr)
 		return ret;
 
@@ -830,7 +830,7 @@
 			wake_up_interruptible(&port->port.open_wait);
 	}
 
-	if (port->port.flags & ASYNC_CTS_FLOW) {
+	if (tty_port_cts_enabled(&port->port)) {
 		if (tty->hw_stopped) {
 			if (status & UART_MSR_CTS) {
 				tty->hw_stopped = 0;
@@ -1520,10 +1520,10 @@
 				
 				tty = tty_port_tty_get(port);
 
-				if (!tty || !tty->termios)
+				if (!tty)
 					ms.cflag = ip->normal_termios.c_cflag;
 				else
-					ms.cflag = tty->termios->c_cflag;
+					ms.cflag = tty->termios.c_cflag;
 				tty_kref_put(tty);
 				spin_lock_irq(&ip->slock);
 				status = inb(ip->ioaddr + UART_MSR);
@@ -1589,13 +1589,13 @@
 
 				tty = tty_port_tty_get(&ip->port);
 
-				if (!tty || !tty->termios) {
+				if (!tty) {
 					cflag = ip->normal_termios.c_cflag;
 					iflag = ip->normal_termios.c_iflag;
 					me->baudrate[p] = tty_termios_baud_rate(&ip->normal_termios);
 				} else {
-					cflag = tty->termios->c_cflag;
-					iflag = tty->termios->c_iflag;
+					cflag = tty->termios.c_cflag;
+					iflag = tty->termios.c_iflag;
 					me->baudrate[p] = tty_get_baud_rate(tty);
 				}
 				tty_kref_put(tty);
@@ -1853,7 +1853,7 @@
 		}
 	}
 
-	if (tty->termios->c_cflag & CRTSCTS) {
+	if (tty->termios.c_cflag & CRTSCTS) {
 		info->MCR &= ~UART_MCR_RTS;
 		outb(info->MCR, info->ioaddr + UART_MCR);
 	}
@@ -1890,7 +1890,7 @@
 		}
 	}
 
-	if (tty->termios->c_cflag & CRTSCTS) {
+	if (tty->termios.c_cflag & CRTSCTS) {
 		info->MCR |= UART_MCR_RTS;
 		outb(info->MCR, info->ioaddr + UART_MCR);
 	}
@@ -1939,14 +1939,14 @@
 	spin_unlock_irqrestore(&info->slock, flags);
 
 	if ((old_termios->c_cflag & CRTSCTS) &&
-			!(tty->termios->c_cflag & CRTSCTS)) {
+			!(tty->termios.c_cflag & CRTSCTS)) {
 		tty->hw_stopped = 0;
 		mxser_start(tty);
 	}
 
 	/* Handle sw stopped */
 	if ((old_termios->c_iflag & IXON) &&
-			!(tty->termios->c_iflag & IXON)) {
+			!(tty->termios.c_iflag & IXON)) {
 		tty->stopped = 0;
 
 		if (info->board->chip_flag) {
@@ -2337,11 +2337,36 @@
  * The MOXA Smartio/Industio serial driver boot-time initialization code!
  */
 
+static bool allow_overlapping_vector;
+module_param(allow_overlapping_vector, bool, S_IRUGO);
+MODULE_PARM_DESC(allow_overlapping_vector, "whether we allow ISA cards to be configured such that vector overlabs IO ports (default=no)");
+
+static bool mxser_overlapping_vector(struct mxser_board *brd)
+{
+	return allow_overlapping_vector &&
+		brd->vector >= brd->ports[0].ioaddr &&
+		brd->vector < brd->ports[0].ioaddr + 8 * brd->info->nports;
+}
+
+static int mxser_request_vector(struct mxser_board *brd)
+{
+	if (mxser_overlapping_vector(brd))
+		return 0;
+	return request_region(brd->vector, 1, "mxser(vector)") ? 0 : -EIO;
+}
+
+static void mxser_release_vector(struct mxser_board *brd)
+{
+	if (mxser_overlapping_vector(brd))
+		return;
+	release_region(brd->vector, 1);
+}
+
 static void mxser_release_ISA_res(struct mxser_board *brd)
 {
 	free_irq(brd->irq, brd);
 	release_region(brd->ports[0].ioaddr, 8 * brd->info->nports);
-	release_region(brd->vector, 1);
+	mxser_release_vector(brd);
 }
 
 static int __devinit mxser_initbrd(struct mxser_board *brd,
@@ -2396,7 +2421,7 @@
 
 static int __init mxser_get_ISA_conf(int cap, struct mxser_board *brd)
 {
-	int id, i, bits;
+	int id, i, bits, ret;
 	unsigned short regs[16], irq;
 	unsigned char scratch, scratch2;
 
@@ -2492,13 +2517,15 @@
 				8 * brd->info->nports - 1);
 		return -EIO;
 	}
-	if (!request_region(brd->vector, 1, "mxser(vector)")) {
+
+	ret = mxser_request_vector(brd);
+	if (ret) {
 		release_region(brd->ports[0].ioaddr, 8 * brd->info->nports);
 		printk(KERN_ERR "mxser: can't request interrupt vector region: "
 				"0x%.8lx-0x%.8lx\n",
 				brd->ports[0].ioaddr, brd->ports[0].ioaddr +
 				8 * brd->info->nports - 1);
-		return -EIO;
+		return ret;
 	}
 	return brd->info->nports;
 
@@ -2598,7 +2625,8 @@
 		goto err_rel3;
 
 	for (i = 0; i < brd->info->nports; i++)
-		tty_register_device(mxvar_sdriver, brd->idx + i, &pdev->dev);
+		tty_port_register_device(&brd->ports[i].port, mxvar_sdriver,
+				brd->idx + i, &pdev->dev);
 
 	pci_set_drvdata(pdev, brd);
 
@@ -2695,7 +2723,8 @@
 
 		brd->idx = m * MXSER_PORTS_PER_BOARD;
 		for (i = 0; i < brd->info->nports; i++)
-			tty_register_device(mxvar_sdriver, brd->idx + i, NULL);
+			tty_port_register_device(&brd->ports[i].port,
+					mxvar_sdriver, brd->idx + i, NULL);
 
 		m++;
 	}
diff --git a/drivers/tty/n_gsm.c b/drivers/tty/n_gsm.c
index c43b683..3e210a4 100644
--- a/drivers/tty/n_gsm.c
+++ b/drivers/tty/n_gsm.c
@@ -108,7 +108,7 @@
  */
 
 struct gsm_msg {
-	struct gsm_msg *next;
+	struct list_head list;
 	u8 addr;		/* DLCI address + flags */
 	u8 ctrl;		/* Control byte + flags */
 	unsigned int len;	/* Length of data block (can be zero) */
@@ -245,8 +245,7 @@
 	unsigned int tx_bytes;		/* TX data outstanding */
 #define TX_THRESH_HI		8192
 #define TX_THRESH_LO		2048
-	struct gsm_msg *tx_head;	/* Pending data packets */
-	struct gsm_msg *tx_tail;
+	struct list_head tx_list;	/* Pending data packets */
 
 	/* Control messages */
 	struct timer_list t2_timer;	/* Retransmit timer for commands */
@@ -663,7 +662,7 @@
 	m->len = len;
 	m->addr = addr;
 	m->ctrl = ctrl;
-	m->next = NULL;
+	INIT_LIST_HEAD(&m->list);
 	return m;
 }
 
@@ -673,22 +672,21 @@
  *
  *	The tty device has called us to indicate that room has appeared in
  *	the transmit queue. Ram more data into the pipe if we have any
+ *	If we have been flow-stopped by a CMD_FCOFF, then we can only
+ *	send messages on DLCI0 until CMD_FCON
  *
  *	FIXME: lock against link layer control transmissions
  */
 
 static void gsm_data_kick(struct gsm_mux *gsm)
 {
-	struct gsm_msg *msg = gsm->tx_head;
+	struct gsm_msg *msg, *nmsg;
 	int len;
 	int skip_sof = 0;
 
-	/* FIXME: We need to apply this solely to data messages */
-	if (gsm->constipated)
-		return;
-
-	while (gsm->tx_head != NULL) {
-		msg = gsm->tx_head;
+	list_for_each_entry_safe(msg, nmsg, &gsm->tx_list, list) {
+		if (gsm->constipated && msg->addr)
+			continue;
 		if (gsm->encoding != 0) {
 			gsm->txframe[0] = GSM1_SOF;
 			len = gsm_stuff_frame(msg->data,
@@ -711,14 +709,13 @@
 						len - skip_sof) < 0)
 			break;
 		/* FIXME: Can eliminate one SOF in many more cases */
-		gsm->tx_head = msg->next;
-		if (gsm->tx_head == NULL)
-			gsm->tx_tail = NULL;
 		gsm->tx_bytes -= msg->len;
-		kfree(msg);
 		/* For a burst of frames skip the extra SOF within the
 		   burst */
 		skip_sof = 1;
+
+		list_del(&msg->list);
+		kfree(msg);
 	}
 }
 
@@ -768,11 +765,7 @@
 	msg->data = dp;
 
 	/* Add to the actual output queue */
-	if (gsm->tx_tail)
-		gsm->tx_tail->next = msg;
-	else
-		gsm->tx_head = msg;
-	gsm->tx_tail = msg;
+	list_add_tail(&msg->list, &gsm->tx_list);
 	gsm->tx_bytes += msg->len;
 	gsm_data_kick(gsm);
 }
@@ -875,7 +868,7 @@
 
 	/* dlci->skb is locked by tx_lock */
 	if (dlci->skb == NULL) {
-		dlci->skb = skb_dequeue(&dlci->skb_list);
+		dlci->skb = skb_dequeue_tail(&dlci->skb_list);
 		if (dlci->skb == NULL)
 			return 0;
 		first = 1;
@@ -886,7 +879,7 @@
 	if (len > gsm->mtu) {
 		if (dlci->adaption == 3) {
 			/* Over long frame, bin it */
-			kfree_skb(dlci->skb);
+			dev_kfree_skb_any(dlci->skb);
 			dlci->skb = NULL;
 			return 0;
 		}
@@ -899,8 +892,11 @@
 
 	/* FIXME: need a timer or something to kick this so it can't
 	   get stuck with no work outstanding and no buffer free */
-	if (msg == NULL)
+	if (msg == NULL) {
+		skb_queue_tail(&dlci->skb_list, dlci->skb);
+		dlci->skb = NULL;
 		return -ENOMEM;
+	}
 	dp = msg->data;
 
 	if (dlci->adaption == 4) { /* Interruptible framed (Packetised Data) */
@@ -912,7 +908,7 @@
 	skb_pull(dlci->skb, len);
 	__gsm_data_queue(dlci, msg);
 	if (last) {
-		kfree_skb(dlci->skb);
+		dev_kfree_skb_any(dlci->skb);
 		dlci->skb = NULL;
 	}
 	return size;
@@ -971,16 +967,22 @@
 static void gsm_dlci_data_kick(struct gsm_dlci *dlci)
 {
 	unsigned long flags;
+	int sweep;
+
+	if (dlci->constipated) 
+		return;
 
 	spin_lock_irqsave(&dlci->gsm->tx_lock, flags);
 	/* If we have nothing running then we need to fire up */
+	sweep = (dlci->gsm->tx_bytes < TX_THRESH_LO);
 	if (dlci->gsm->tx_bytes == 0) {
 		if (dlci->net)
 			gsm_dlci_data_output_framed(dlci->gsm, dlci);
 		else
 			gsm_dlci_data_output(dlci->gsm, dlci);
-	} else if (dlci->gsm->tx_bytes < TX_THRESH_LO)
-		gsm_dlci_data_sweep(dlci->gsm);
+	}
+	if (sweep)
+ 		gsm_dlci_data_sweep(dlci->gsm);
 	spin_unlock_irqrestore(&dlci->gsm->tx_lock, flags);
 }
 
@@ -1027,6 +1029,7 @@
 {
 	int  mlines = 0;
 	u8 brk = 0;
+	int fc;
 
 	/* The modem status command can either contain one octet (v.24 signals)
 	   or two octets (v.24 signals + break signals). The length field will
@@ -1038,19 +1041,21 @@
 	else {
 		brk = modem & 0x7f;
 		modem = (modem >> 7) & 0x7f;
-	};
+	}
 
 	/* Flow control/ready to communicate */
-	if (modem & MDM_FC) {
+	fc = (modem & MDM_FC) || !(modem & MDM_RTR);
+	if (fc && !dlci->constipated) {
 		/* Need to throttle our output on this device */
 		dlci->constipated = 1;
-	}
-	if (modem & MDM_RTC) {
-		mlines |= TIOCM_DSR | TIOCM_DTR;
+	} else if (!fc && dlci->constipated) {
 		dlci->constipated = 0;
 		gsm_dlci_data_kick(dlci);
 	}
+
 	/* Map modem bits */
+	if (modem & MDM_RTC)
+		mlines |= TIOCM_DSR | TIOCM_DTR;
 	if (modem & MDM_RTR)
 		mlines |= TIOCM_RTS | TIOCM_CTS;
 	if (modem & MDM_IC)
@@ -1061,7 +1066,7 @@
 	/* Carrier drop -> hangup */
 	if (tty) {
 		if ((mlines & TIOCM_CD) == 0 && (dlci->modem_rx & TIOCM_CD))
-			if (!(tty->termios->c_cflag & CLOCAL))
+			if (!(tty->termios.c_cflag & CLOCAL))
 				tty_hangup(tty);
 		if (brk & 0x01)
 			tty_insert_flip_char(tty, 0, TTY_BREAK);
@@ -1190,6 +1195,8 @@
 							u8 *data, int clen)
 {
 	u8 buf[1];
+	unsigned long flags;
+
 	switch (command) {
 	case CMD_CLD: {
 		struct gsm_dlci *dlci = gsm->dlci[0];
@@ -1206,16 +1213,18 @@
 		gsm_control_reply(gsm, CMD_TEST, data, clen);
 		break;
 	case CMD_FCON:
-		/* Modem wants us to STFU */
-		gsm->constipated = 1;
-		gsm_control_reply(gsm, CMD_FCON, NULL, 0);
-		break;
-	case CMD_FCOFF:
 		/* Modem can accept data again */
 		gsm->constipated = 0;
-		gsm_control_reply(gsm, CMD_FCOFF, NULL, 0);
+		gsm_control_reply(gsm, CMD_FCON, NULL, 0);
 		/* Kick the link in case it is idling */
+		spin_lock_irqsave(&gsm->tx_lock, flags);
 		gsm_data_kick(gsm);
+		spin_unlock_irqrestore(&gsm->tx_lock, flags);
+		break;
+	case CMD_FCOFF:
+		/* Modem wants us to STFU */
+		gsm->constipated = 1;
+		gsm_control_reply(gsm, CMD_FCOFF, NULL, 0);
 		break;
 	case CMD_MSC:
 		/* Out of band modem line change indicator for a DLCI */
@@ -1668,7 +1677,7 @@
 	dlci->gsm->dlci[dlci->addr] = NULL;
 	kfifo_free(dlci->fifo);
 	while ((dlci->skb = skb_dequeue(&dlci->skb_list)))
-		kfree_skb(dlci->skb);
+		dev_kfree_skb(dlci->skb);
 	kfree(dlci);
 }
 
@@ -2007,7 +2016,7 @@
 {
 	int i;
 	struct gsm_dlci *dlci = gsm->dlci[0];
-	struct gsm_msg *txq;
+	struct gsm_msg *txq, *ntxq;
 	struct gsm_control *gc;
 
 	gsm->dead = 1;
@@ -2042,11 +2051,9 @@
 		if (gsm->dlci[i])
 			gsm_dlci_release(gsm->dlci[i]);
 	/* Now wipe the queues */
-	for (txq = gsm->tx_head; txq != NULL; txq = gsm->tx_head) {
-		gsm->tx_head = txq->next;
+	list_for_each_entry_safe(txq, ntxq, &gsm->tx_list, list)
 		kfree(txq);
-	}
-	gsm->tx_tail = NULL;
+	INIT_LIST_HEAD(&gsm->tx_list);
 }
 EXPORT_SYMBOL_GPL(gsm_cleanup_mux);
 
@@ -2157,6 +2164,7 @@
 	}
 	spin_lock_init(&gsm->lock);
 	kref_init(&gsm->ref);
+	INIT_LIST_HEAD(&gsm->tx_list);
 
 	gsm->t1 = T1;
 	gsm->t2 = T2;
@@ -2273,7 +2281,7 @@
 			gsm->error(gsm, *dp, flags);
 			break;
 		default:
-			WARN_ONCE("%s: unknown flag %d\n",
+			WARN_ONCE(1, "%s: unknown flag %d\n",
 			       tty_name(tty, buf), flags);
 			break;
 		}
@@ -2377,12 +2385,12 @@
 
 	/* Queue poll */
 	clear_bit(TTY_DO_WRITE_WAKEUP, &tty->flags);
+	spin_lock_irqsave(&gsm->tx_lock, flags);
 	gsm_data_kick(gsm);
 	if (gsm->tx_bytes < TX_THRESH_LO) {
-		spin_lock_irqsave(&gsm->tx_lock, flags);
 		gsm_dlci_data_sweep(gsm);
-		spin_unlock_irqrestore(&gsm->tx_lock, flags);
 	}
+	spin_unlock_irqrestore(&gsm->tx_lock, flags);
 }
 
 /**
@@ -2868,14 +2876,14 @@
 	.dtr_rts = gsm_dtr_rts,
 };
 
-
-static int gsmtty_open(struct tty_struct *tty, struct file *filp)
+static int gsmtty_install(struct tty_driver *driver, struct tty_struct *tty)
 {
 	struct gsm_mux *gsm;
 	struct gsm_dlci *dlci;
-	struct tty_port *port;
 	unsigned int line = tty->index;
 	unsigned int mux = line >> 6;
+	bool alloc = false;
+	int ret;
 
 	line = line & 0x3F;
 
@@ -2889,14 +2897,35 @@
 	gsm = gsm_mux[mux];
 	if (gsm->dead)
 		return -EL2HLT;
+	/* If DLCI 0 is not yet fully open return an error. This is ok from a locking
+	   perspective as we don't have to worry about this if DLCI0 is lost */
+	if (gsm->dlci[0] && gsm->dlci[0]->state != DLCI_OPEN) 
+		return -EL2NSYNC;
 	dlci = gsm->dlci[line];
-	if (dlci == NULL)
+	if (dlci == NULL) {
+		alloc = true;
 		dlci = gsm_dlci_alloc(gsm, line);
+	}
 	if (dlci == NULL)
 		return -ENOMEM;
-	port = &dlci->port;
-	port->count++;
+	ret = tty_port_install(&dlci->port, driver, tty);
+	if (ret) {
+		if (alloc)
+			dlci_put(dlci);
+		return ret;
+	}
+
 	tty->driver_data = dlci;
+
+	return 0;
+}
+
+static int gsmtty_open(struct tty_struct *tty, struct file *filp)
+{
+	struct gsm_dlci *dlci = tty->driver_data;
+	struct tty_port *port = &dlci->port;
+
+	port->count++;
 	dlci_get(dlci);
 	dlci_get(dlci->gsm->dlci[0]);
 	mux_get(dlci->gsm);
@@ -3043,13 +3072,13 @@
 	   the RPN control message. This however rapidly gets nasty as we
 	   then have to remap modem signals each way according to whether
 	   our virtual cable is null modem etc .. */
-	tty_termios_copy_hw(tty->termios, old);
+	tty_termios_copy_hw(&tty->termios, old);
 }
 
 static void gsmtty_throttle(struct tty_struct *tty)
 {
 	struct gsm_dlci *dlci = tty->driver_data;
-	if (tty->termios->c_cflag & CRTSCTS)
+	if (tty->termios.c_cflag & CRTSCTS)
 		dlci->modem_tx &= ~TIOCM_DTR;
 	dlci->throttled = 1;
 	/* Send an MSC with DTR cleared */
@@ -3059,7 +3088,7 @@
 static void gsmtty_unthrottle(struct tty_struct *tty)
 {
 	struct gsm_dlci *dlci = tty->driver_data;
-	if (tty->termios->c_cflag & CRTSCTS)
+	if (tty->termios.c_cflag & CRTSCTS)
 		dlci->modem_tx |= TIOCM_DTR;
 	dlci->throttled = 0;
 	/* Send an MSC with DTR set */
@@ -3085,6 +3114,7 @@
 
 /* Virtual ttys for the demux */
 static const struct tty_operations gsmtty_ops = {
+	.install		= gsmtty_install,
 	.open			= gsmtty_open,
 	.close			= gsmtty_close,
 	.write			= gsmtty_write,
diff --git a/drivers/tty/n_r3964.c b/drivers/tty/n_r3964.c
index 5c6c314..1e64050 100644
--- a/drivers/tty/n_r3964.c
+++ b/drivers/tty/n_r3964.c
@@ -1065,7 +1065,7 @@
 
 	TRACE_L("read()");
 
-	tty_lock();
+	tty_lock(tty);
 
 	pClient = findClient(pInfo, task_pid(current));
 	if (pClient) {
@@ -1077,7 +1077,7 @@
 				goto unlock;
 			}
 			/* block until there is a message: */
-			wait_event_interruptible_tty(pInfo->read_wait,
+			wait_event_interruptible_tty(tty, pInfo->read_wait,
 					(pMsg = remove_msg(pInfo, pClient)));
 		}
 
@@ -1107,7 +1107,7 @@
 	}
 	ret = -EPERM;
 unlock:
-	tty_unlock();
+	tty_unlock(tty);
 	return ret;
 }
 
@@ -1156,7 +1156,7 @@
 	pHeader->locks = 0;
 	pHeader->owner = NULL;
 
-	tty_lock();
+	tty_lock(tty);
 
 	pClient = findClient(pInfo, task_pid(current));
 	if (pClient) {
@@ -1175,7 +1175,7 @@
 	add_tx_queue(pInfo, pHeader);
 	trigger_transmit(pInfo);
 
-	tty_unlock();
+	tty_unlock(tty);
 
 	return 0;
 }
diff --git a/drivers/tty/n_tty.c b/drivers/tty/n_tty.c
index ee1c268..8c0b7b4 100644
--- a/drivers/tty/n_tty.c
+++ b/drivers/tty/n_tty.c
@@ -92,10 +92,18 @@
 
 static void n_tty_set_room(struct tty_struct *tty)
 {
-	/* tty->read_cnt is not read locked ? */
-	int	left = N_TTY_BUF_SIZE - tty->read_cnt - 1;
+	int left;
 	int old_left;
 
+	/* tty->read_cnt is not read locked ? */
+	if (I_PARMRK(tty)) {
+		/* Multiply read_cnt by 3, since each byte might take up to
+		 * three times as many spaces when PARMRK is set (depending on
+		 * its flags, e.g. parity error). */
+		left = N_TTY_BUF_SIZE - tty->read_cnt * 3 - 1;
+	} else
+		left = N_TTY_BUF_SIZE - tty->read_cnt - 1;
+
 	/*
 	 * If we are doing input canonicalization, and there are no
 	 * pending newlines, let characters through without limit, so
@@ -1432,6 +1440,12 @@
 	 */
 	if (tty->receive_room < TTY_THRESHOLD_THROTTLE)
 		tty_throttle(tty);
+
+        /* FIXME: there is a tiny race here if the receive room check runs
+           before the other work executes and empties the buffer (upping
+           the receiving room and unthrottling. We then throttle and get
+           stuck. This has been observed and traced down by Vincent Pillet/
+           We need to address this when we sort out out the rx path locking */
 }
 
 int is_ignored(int sig)
@@ -1460,7 +1474,7 @@
 	BUG_ON(!tty);
 
 	if (old)
-		canon_change = (old->c_lflag ^ tty->termios->c_lflag) & ICANON;
+		canon_change = (old->c_lflag ^ tty->termios.c_lflag) & ICANON;
 	if (canon_change) {
 		memset(&tty->read_flags, 0, sizeof tty->read_flags);
 		tty->canon_head = tty->read_tail;
@@ -1728,7 +1742,8 @@
 
 do_it_again:
 
-	BUG_ON(!tty->read_buf);
+	if (WARN_ON(!tty->read_buf))
+		return -EAGAIN;
 
 	c = job_control(tty, file);
 	if (c < 0)
@@ -1832,13 +1847,13 @@
 
 		if (tty->icanon && !L_EXTPROC(tty)) {
 			/* N.B. avoid overrun if nr == 0 */
+			spin_lock_irqsave(&tty->read_lock, flags);
 			while (nr && tty->read_cnt) {
 				int eol;
 
 				eol = test_and_clear_bit(tty->read_tail,
 						tty->read_flags);
 				c = tty->read_buf[tty->read_tail];
-				spin_lock_irqsave(&tty->read_lock, flags);
 				tty->read_tail = ((tty->read_tail+1) &
 						  (N_TTY_BUF_SIZE-1));
 				tty->read_cnt--;
@@ -1856,15 +1871,19 @@
 					if (tty_put_user(tty, c, b++)) {
 						retval = -EFAULT;
 						b--;
+						spin_lock_irqsave(&tty->read_lock, flags);
 						break;
 					}
 					nr--;
 				}
 				if (eol) {
 					tty_audit_push(tty);
+					spin_lock_irqsave(&tty->read_lock, flags);
 					break;
 				}
+				spin_lock_irqsave(&tty->read_lock, flags);
 			}
+			spin_unlock_irqrestore(&tty->read_lock, flags);
 			if (retval)
 				break;
 		} else {
diff --git a/drivers/tty/nozomi.c b/drivers/tty/nozomi.c
index e7592f9..b917c94 100644
--- a/drivers/tty/nozomi.c
+++ b/drivers/tty/nozomi.c
@@ -1473,8 +1473,8 @@
 		port->dc = dc;
 		tty_port_init(&port->port);
 		port->port.ops = &noz_tty_port_ops;
-		tty_dev = tty_register_device(ntty_driver, dc->index_start + i,
-							&pdev->dev);
+		tty_dev = tty_port_register_device(&port->port, ntty_driver,
+				dc->index_start + i, &pdev->dev);
 
 		if (IS_ERR(tty_dev)) {
 			ret = PTR_ERR(tty_dev);
diff --git a/drivers/tty/pty.c b/drivers/tty/pty.c
index 5505ffc..2bace84 100644
--- a/drivers/tty/pty.c
+++ b/drivers/tty/pty.c
@@ -47,6 +47,7 @@
 	wake_up_interruptible(&tty->read_wait);
 	wake_up_interruptible(&tty->write_wait);
 	tty->packet = 0;
+	/* Review - krefs on tty_link ?? */
 	if (!tty->link)
 		return;
 	tty->link->packet = 0;
@@ -62,9 +63,9 @@
 		        mutex_unlock(&devpts_mutex);
 		}
 #endif
-		tty_unlock();
+		tty_unlock(tty);
 		tty_vhangup(tty->link);
-		tty_lock();
+		tty_lock(tty);
 	}
 }
 
@@ -231,8 +232,8 @@
 static void pty_set_termios(struct tty_struct *tty,
 					struct ktermios *old_termios)
 {
-	tty->termios->c_cflag &= ~(CSIZE | PARENB);
-	tty->termios->c_cflag |= (CS8 | CREAD);
+	tty->termios.c_cflag &= ~(CSIZE | PARENB);
+	tty->termios.c_cflag |= (CS8 | CREAD);
 }
 
 /**
@@ -282,60 +283,110 @@
 	return 0;
 }
 
-/* Traditional BSD devices */
-#ifdef CONFIG_LEGACY_PTYS
-
-static int pty_install(struct tty_driver *driver, struct tty_struct *tty)
+/**
+ *	pty_common_install		-	set up the pty pair
+ *	@driver: the pty driver
+ *	@tty: the tty being instantiated
+ *	@bool: legacy, true if this is BSD style
+ *
+ *	Perform the initial set up for the tty/pty pair. Called from the
+ *	tty layer when the port is first opened.
+ *
+ *	Locking: the caller must hold the tty_mutex
+ */
+static int pty_common_install(struct tty_driver *driver, struct tty_struct *tty,
+		bool legacy)
 {
 	struct tty_struct *o_tty;
+	struct tty_port *ports[2];
 	int idx = tty->index;
-	int retval;
+	int retval = -ENOMEM;
 
 	o_tty = alloc_tty_struct();
 	if (!o_tty)
-		return -ENOMEM;
+		goto err;
+	ports[0] = kmalloc(sizeof **ports, GFP_KERNEL);
+	ports[1] = kmalloc(sizeof **ports, GFP_KERNEL);
+	if (!ports[0] || !ports[1])
+		goto err_free_tty;
 	if (!try_module_get(driver->other->owner)) {
 		/* This cannot in fact currently happen */
-		retval = -ENOMEM;
 		goto err_free_tty;
 	}
 	initialize_tty_struct(o_tty, driver->other, idx);
 
-	/* We always use new tty termios data so we can do this
-	   the easy way .. */
-	retval = tty_init_termios(tty);
-	if (retval)
-		goto err_deinit_tty;
+	if (legacy) {
+		/* We always use new tty termios data so we can do this
+		   the easy way .. */
+		retval = tty_init_termios(tty);
+		if (retval)
+			goto err_deinit_tty;
 
-	retval = tty_init_termios(o_tty);
-	if (retval)
-		goto err_free_termios;
+		retval = tty_init_termios(o_tty);
+		if (retval)
+			goto err_free_termios;
+
+		driver->other->ttys[idx] = o_tty;
+		driver->ttys[idx] = tty;
+	} else {
+		memset(&tty->termios_locked, 0, sizeof(tty->termios_locked));
+		tty->termios = driver->init_termios;
+		memset(&o_tty->termios_locked, 0, sizeof(tty->termios_locked));
+		o_tty->termios = driver->other->init_termios;
+	}
 
 	/*
 	 * Everything allocated ... set up the o_tty structure.
 	 */
-	driver->other->ttys[idx] = o_tty;
 	tty_driver_kref_get(driver->other);
 	if (driver->subtype == PTY_TYPE_MASTER)
 		o_tty->count++;
 	/* Establish the links in both directions */
 	tty->link   = o_tty;
 	o_tty->link = tty;
+	tty_port_init(ports[0]);
+	tty_port_init(ports[1]);
+	o_tty->port = ports[0];
+	tty->port = ports[1];
 
 	tty_driver_kref_get(driver);
 	tty->count++;
-	driver->ttys[idx] = tty;
 	return 0;
 err_free_termios:
-	tty_free_termios(tty);
+	if (legacy)
+		tty_free_termios(tty);
 err_deinit_tty:
 	deinitialize_tty_struct(o_tty);
 	module_put(o_tty->driver->owner);
 err_free_tty:
+	kfree(ports[0]);
+	kfree(ports[1]);
 	free_tty_struct(o_tty);
+err:
 	return retval;
 }
 
+static void pty_cleanup(struct tty_struct *tty)
+{
+	kfree(tty->port);
+}
+
+/* Traditional BSD devices */
+#ifdef CONFIG_LEGACY_PTYS
+
+static int pty_install(struct tty_driver *driver, struct tty_struct *tty)
+{
+	return pty_common_install(driver, tty, true);
+}
+
+static void pty_remove(struct tty_driver *driver, struct tty_struct *tty)
+{
+	struct tty_struct *pair = tty->link;
+	driver->ttys[tty->index] = NULL;
+	if (pair)
+		pair->driver->ttys[pair->index] = NULL;
+}
+
 static int pty_bsd_ioctl(struct tty_struct *tty,
 			 unsigned int cmd, unsigned long arg)
 {
@@ -366,7 +417,9 @@
 	.unthrottle = pty_unthrottle,
 	.set_termios = pty_set_termios,
 	.ioctl = pty_bsd_ioctl,
-	.resize = pty_resize
+	.cleanup = pty_cleanup,
+	.resize = pty_resize,
+	.remove = pty_remove
 };
 
 static const struct tty_operations slave_pty_ops_bsd = {
@@ -379,7 +432,9 @@
 	.chars_in_buffer = pty_chars_in_buffer,
 	.unthrottle = pty_unthrottle,
 	.set_termios = pty_set_termios,
-	.resize = pty_resize
+	.cleanup = pty_cleanup,
+	.resize = pty_resize,
+	.remove = pty_remove
 };
 
 static void __init legacy_pty_init(void)
@@ -389,12 +444,18 @@
 	if (legacy_count <= 0)
 		return;
 
-	pty_driver = alloc_tty_driver(legacy_count);
-	if (!pty_driver)
+	pty_driver = tty_alloc_driver(legacy_count,
+			TTY_DRIVER_RESET_TERMIOS |
+			TTY_DRIVER_REAL_RAW |
+			TTY_DRIVER_DYNAMIC_ALLOC);
+	if (IS_ERR(pty_driver))
 		panic("Couldn't allocate pty driver");
 
-	pty_slave_driver = alloc_tty_driver(legacy_count);
-	if (!pty_slave_driver)
+	pty_slave_driver = tty_alloc_driver(legacy_count,
+			TTY_DRIVER_RESET_TERMIOS |
+			TTY_DRIVER_REAL_RAW |
+			TTY_DRIVER_DYNAMIC_ALLOC);
+	if (IS_ERR(pty_slave_driver))
 		panic("Couldn't allocate pty slave driver");
 
 	pty_driver->driver_name = "pty_master";
@@ -410,7 +471,6 @@
 	pty_driver->init_termios.c_lflag = 0;
 	pty_driver->init_termios.c_ispeed = 38400;
 	pty_driver->init_termios.c_ospeed = 38400;
-	pty_driver->flags = TTY_DRIVER_RESET_TERMIOS | TTY_DRIVER_REAL_RAW;
 	pty_driver->other = pty_slave_driver;
 	tty_set_operations(pty_driver, &master_pty_ops_bsd);
 
@@ -424,8 +484,6 @@
 	pty_slave_driver->init_termios.c_cflag = B38400 | CS8 | CREAD;
 	pty_slave_driver->init_termios.c_ispeed = 38400;
 	pty_slave_driver->init_termios.c_ospeed = 38400;
-	pty_slave_driver->flags = TTY_DRIVER_RESET_TERMIOS |
-					TTY_DRIVER_REAL_RAW;
 	pty_slave_driver->other = pty_driver;
 	tty_set_operations(pty_slave_driver, &slave_pty_ops_bsd);
 
@@ -497,78 +555,22 @@
 	return tty;
 }
 
-static void pty_unix98_shutdown(struct tty_struct *tty)
-{
-	tty_driver_remove_tty(tty->driver, tty);
-	/* We have our own method as we don't use the tty index */
-	kfree(tty->termios);
-}
-
 /* We have no need to install and remove our tty objects as devpts does all
    the work for us */
 
 static int pty_unix98_install(struct tty_driver *driver, struct tty_struct *tty)
 {
-	struct tty_struct *o_tty;
-	int idx = tty->index;
-
-	o_tty = alloc_tty_struct();
-	if (!o_tty)
-		return -ENOMEM;
-	if (!try_module_get(driver->other->owner)) {
-		/* This cannot in fact currently happen */
-		goto err_free_tty;
-	}
-	initialize_tty_struct(o_tty, driver->other, idx);
-
-	tty->termios = kzalloc(sizeof(struct ktermios[2]), GFP_KERNEL);
-	if (tty->termios == NULL)
-		goto err_free_mem;
-	*tty->termios = driver->init_termios;
-	tty->termios_locked = tty->termios + 1;
-
-	o_tty->termios = kzalloc(sizeof(struct ktermios[2]), GFP_KERNEL);
-	if (o_tty->termios == NULL)
-		goto err_free_mem;
-	*o_tty->termios = driver->other->init_termios;
-	o_tty->termios_locked = o_tty->termios + 1;
-
-	tty_driver_kref_get(driver->other);
-	if (driver->subtype == PTY_TYPE_MASTER)
-		o_tty->count++;
-	/* Establish the links in both directions */
-	tty->link   = o_tty;
-	o_tty->link = tty;
-	/*
-	 * All structures have been allocated, so now we install them.
-	 * Failures after this point use release_tty to clean up, so
-	 * there's no need to null out the local pointers.
-	 */
-	tty_driver_kref_get(driver);
-	tty->count++;
-	return 0;
-err_free_mem:
-	deinitialize_tty_struct(o_tty);
-	kfree(o_tty->termios);
-	kfree(tty->termios);
-	module_put(o_tty->driver->owner);
-err_free_tty:
-	free_tty_struct(o_tty);
-	return -ENOMEM;
+	return pty_common_install(driver, tty, false);
 }
 
-static void ptm_unix98_remove(struct tty_driver *driver, struct tty_struct *tty)
-{
-}
-
-static void pts_unix98_remove(struct tty_driver *driver, struct tty_struct *tty)
+static void pty_unix98_remove(struct tty_driver *driver, struct tty_struct *tty)
 {
 }
 
 static const struct tty_operations ptm_unix98_ops = {
 	.lookup = ptm_unix98_lookup,
 	.install = pty_unix98_install,
-	.remove = ptm_unix98_remove,
+	.remove = pty_unix98_remove,
 	.open = pty_open,
 	.close = pty_close,
 	.write = pty_write,
@@ -578,14 +580,14 @@
 	.unthrottle = pty_unthrottle,
 	.set_termios = pty_set_termios,
 	.ioctl = pty_unix98_ioctl,
-	.shutdown = pty_unix98_shutdown,
-	.resize = pty_resize
+	.resize = pty_resize,
+	.cleanup = pty_cleanup
 };
 
 static const struct tty_operations pty_unix98_ops = {
 	.lookup = pts_unix98_lookup,
 	.install = pty_unix98_install,
-	.remove = pts_unix98_remove,
+	.remove = pty_unix98_remove,
 	.open = pty_open,
 	.close = pty_close,
 	.write = pty_write,
@@ -594,7 +596,7 @@
 	.chars_in_buffer = pty_chars_in_buffer,
 	.unthrottle = pty_unthrottle,
 	.set_termios = pty_set_termios,
-	.shutdown = pty_unix98_shutdown
+	.cleanup = pty_cleanup,
 };
 
 /**
@@ -622,26 +624,27 @@
 		return retval;
 
 	/* find a device that is not in use. */
-	tty_lock();
+	mutex_lock(&devpts_mutex);
 	index = devpts_new_index(inode);
-	tty_unlock();
 	if (index < 0) {
 		retval = index;
 		goto err_file;
 	}
 
-	mutex_lock(&tty_mutex);
-	mutex_lock(&devpts_mutex);
-	tty = tty_init_dev(ptm_driver, index);
 	mutex_unlock(&devpts_mutex);
-	tty_lock();
-	mutex_unlock(&tty_mutex);
+
+	mutex_lock(&tty_mutex);
+	tty = tty_init_dev(ptm_driver, index);
 
 	if (IS_ERR(tty)) {
 		retval = PTR_ERR(tty);
 		goto out;
 	}
 
+	/* The tty returned here is locked so we can safely
+	   drop the mutex */
+	mutex_unlock(&tty_mutex);
+
 	set_bit(TTY_PTY_LOCK, &tty->flags); /* LOCK THE SLAVE */
 
 	tty_add_file(tty, filp);
@@ -654,16 +657,17 @@
 	if (retval)
 		goto err_release;
 
-	tty_unlock();
+	tty_unlock(tty);
 	return 0;
 err_release:
-	tty_unlock();
+	tty_unlock(tty);
 	tty_release(inode, filp);
 	return retval;
 out:
+	mutex_unlock(&tty_mutex);
 	devpts_kill_index(inode, index);
-	tty_unlock();
 err_file:
+        mutex_unlock(&devpts_mutex);
 	tty_free_file(filp);
 	return retval;
 }
@@ -672,11 +676,21 @@
 
 static void __init unix98_pty_init(void)
 {
-	ptm_driver = alloc_tty_driver(NR_UNIX98_PTY_MAX);
-	if (!ptm_driver)
+	ptm_driver = tty_alloc_driver(NR_UNIX98_PTY_MAX,
+			TTY_DRIVER_RESET_TERMIOS |
+			TTY_DRIVER_REAL_RAW |
+			TTY_DRIVER_DYNAMIC_DEV |
+			TTY_DRIVER_DEVPTS_MEM |
+			TTY_DRIVER_DYNAMIC_ALLOC);
+	if (IS_ERR(ptm_driver))
 		panic("Couldn't allocate Unix98 ptm driver");
-	pts_driver = alloc_tty_driver(NR_UNIX98_PTY_MAX);
-	if (!pts_driver)
+	pts_driver = tty_alloc_driver(NR_UNIX98_PTY_MAX,
+			TTY_DRIVER_RESET_TERMIOS |
+			TTY_DRIVER_REAL_RAW |
+			TTY_DRIVER_DYNAMIC_DEV |
+			TTY_DRIVER_DEVPTS_MEM |
+			TTY_DRIVER_DYNAMIC_ALLOC);
+	if (IS_ERR(pts_driver))
 		panic("Couldn't allocate Unix98 pts driver");
 
 	ptm_driver->driver_name = "pty_master";
@@ -692,8 +706,6 @@
 	ptm_driver->init_termios.c_lflag = 0;
 	ptm_driver->init_termios.c_ispeed = 38400;
 	ptm_driver->init_termios.c_ospeed = 38400;
-	ptm_driver->flags = TTY_DRIVER_RESET_TERMIOS | TTY_DRIVER_REAL_RAW |
-		TTY_DRIVER_DYNAMIC_DEV | TTY_DRIVER_DEVPTS_MEM;
 	ptm_driver->other = pts_driver;
 	tty_set_operations(ptm_driver, &ptm_unix98_ops);
 
@@ -707,8 +719,6 @@
 	pts_driver->init_termios.c_cflag = B38400 | CS8 | CREAD;
 	pts_driver->init_termios.c_ispeed = 38400;
 	pts_driver->init_termios.c_ospeed = 38400;
-	pts_driver->flags = TTY_DRIVER_RESET_TERMIOS | TTY_DRIVER_REAL_RAW |
-		TTY_DRIVER_DYNAMIC_DEV | TTY_DRIVER_DEVPTS_MEM;
 	pts_driver->other = ptm_driver;
 	tty_set_operations(pts_driver, &pty_unix98_ops);
 
diff --git a/drivers/tty/rocket.c b/drivers/tty/rocket.c
index 777d5f9..9700d34 100644
--- a/drivers/tty/rocket.c
+++ b/drivers/tty/rocket.c
@@ -704,8 +704,8 @@
 	spin_lock_init(&info->slock);
 	mutex_init(&info->write_mtx);
 	rp_table[line] = info;
-	tty_register_device(rocket_driver, line, pci_dev ? &pci_dev->dev :
-			NULL);
+	tty_port_register_device(&info->port, rocket_driver, line,
+			pci_dev ? &pci_dev->dev : NULL);
 }
 
 /*
@@ -720,7 +720,7 @@
 	unsigned rocketMode;
 	int bits, baud, divisor;
 	CHANNEL_t *cp;
-	struct ktermios *t = tty->termios;
+	struct ktermios *t = &tty->termios;
 
 	cp = &info->channel;
 	cflag = t->c_cflag;
@@ -978,7 +978,7 @@
 			tty->alt_speed = 460800;
 
 		configure_r_port(tty, info, NULL);
-		if (tty->termios->c_cflag & CBAUD) {
+		if (tty->termios.c_cflag & CBAUD) {
 			sSetDTR(cp);
 			sSetRTS(cp);
 		}
@@ -1089,35 +1089,35 @@
 	if (rocket_paranoia_check(info, "rp_set_termios"))
 		return;
 
-	cflag = tty->termios->c_cflag;
+	cflag = tty->termios.c_cflag;
 
 	/*
 	 * This driver doesn't support CS5 or CS6
 	 */
 	if (((cflag & CSIZE) == CS5) || ((cflag & CSIZE) == CS6))
-		tty->termios->c_cflag =
+		tty->termios.c_cflag =
 		    ((cflag & ~CSIZE) | (old_termios->c_cflag & CSIZE));
 	/* Or CMSPAR */
-	tty->termios->c_cflag &= ~CMSPAR;
+	tty->termios.c_cflag &= ~CMSPAR;
 
 	configure_r_port(tty, info, old_termios);
 
 	cp = &info->channel;
 
 	/* Handle transition to B0 status */
-	if ((old_termios->c_cflag & CBAUD) && !(tty->termios->c_cflag & CBAUD)) {
+	if ((old_termios->c_cflag & CBAUD) && !(tty->termios.c_cflag & CBAUD)) {
 		sClrDTR(cp);
 		sClrRTS(cp);
 	}
 
 	/* Handle transition away from B0 status */
-	if (!(old_termios->c_cflag & CBAUD) && (tty->termios->c_cflag & CBAUD)) {
-		if (!tty->hw_stopped || !(tty->termios->c_cflag & CRTSCTS))
+	if (!(old_termios->c_cflag & CBAUD) && (tty->termios.c_cflag & CBAUD)) {
+		if (!tty->hw_stopped || !(tty->termios.c_cflag & CRTSCTS))
 			sSetRTS(cp);
 		sSetDTR(cp);
 	}
 
-	if ((old_termios->c_cflag & CRTSCTS) && !(tty->termios->c_cflag & CRTSCTS)) {
+	if ((old_termios->c_cflag & CRTSCTS) && !(tty->termios.c_cflag & CRTSCTS)) {
 		tty->hw_stopped = 0;
 		rp_start(tty);
 	}
diff --git a/drivers/tty/serial/68328serial.c b/drivers/tty/serial/68328serial.c
index 3ed20e4..66c38a3 100644
--- a/drivers/tty/serial/68328serial.c
+++ b/drivers/tty/serial/68328serial.c
@@ -515,7 +515,7 @@
 	unsigned cflag;
 	int	i;
 
-	cflag = tty->termios->c_cflag;
+	cflag = tty->termios.c_cflag;
 	if (!(port = info->port))
 		return;
 
@@ -617,7 +617,7 @@
 	if (serial_paranoia_check(info, tty->name, "rs_set_ldisc"))
 		return;
 
-	info->is_cons = (tty->termios->c_line == N_TTY);
+	info->is_cons = (tty->termios.c_line == N_TTY);
 	
 	printk("ttyS%d console mode %s\n", info->line, info->is_cons ? "on" : "off");
 }
@@ -985,7 +985,7 @@
 	change_speed(info, tty);
 
 	if ((old_termios->c_cflag & CRTSCTS) &&
-	    !(tty->termios->c_cflag & CRTSCTS)) {
+	    !(tty->termios.c_cflag & CRTSCTS)) {
 		tty->hw_stopped = 0;
 		rs_start(tty);
 	}
@@ -1070,7 +1070,7 @@
 		if (tty->ldisc.close)
 			(tty->ldisc.close)(tty);
 		tty->ldisc = ldiscs[N_TTY];
-		tty->termios->c_line = N_TTY;
+		tty->termios.c_line = N_TTY;
 		if (tty->ldisc.open)
 			(tty->ldisc.open)(tty);
 	}
@@ -1189,12 +1189,6 @@
 	serial_driver->flags = TTY_DRIVER_REAL_RAW;
 	tty_set_operations(serial_driver, &rs_ops);
 
-	if (tty_register_driver(serial_driver)) {
-		put_tty_driver(serial_driver);
-		printk(KERN_ERR "Couldn't register serial driver\n");
-		return -ENOMEM;
-	}
-
 	local_irq_save(flags);
 
 	for(i=0;i<NR_PORTS;i++) {
@@ -1224,8 +1218,17 @@
 			    0,
 			    "M68328_UART", info))
                 panic("Unable to attach 68328 serial interrupt\n");
+
+	    tty_port_link_device(&info->tport, serial_driver, i);
 	}
 	local_irq_restore(flags);
+
+	if (tty_register_driver(serial_driver)) {
+		put_tty_driver(serial_driver);
+		printk(KERN_ERR "Couldn't register serial driver\n");
+		return -ENOMEM;
+	}
+
 	return 0;
 }
 
diff --git a/drivers/tty/serial/8250/8250.c b/drivers/tty/serial/8250/8250.c
index 8123f78..d4e0b07 100644
--- a/drivers/tty/serial/8250/8250.c
+++ b/drivers/tty/serial/8250/8250.c
@@ -2202,6 +2202,7 @@
 	unsigned char cval, fcr = 0;
 	unsigned long flags;
 	unsigned int baud, quot;
+	int fifo_bug = 0;
 
 	switch (termios->c_cflag & CSIZE) {
 	case CS5:
@@ -2221,8 +2222,11 @@
 
 	if (termios->c_cflag & CSTOPB)
 		cval |= UART_LCR_STOP;
-	if (termios->c_cflag & PARENB)
+	if (termios->c_cflag & PARENB) {
 		cval |= UART_LCR_PARITY;
+		if (up->bugs & UART_BUG_PARITY)
+			fifo_bug = 1;
+	}
 	if (!(termios->c_cflag & PARODD))
 		cval |= UART_LCR_EPAR;
 #ifdef CMSPAR
@@ -2246,7 +2250,7 @@
 
 	if (up->capabilities & UART_CAP_FIFO && port->fifosize > 1) {
 		fcr = uart_config[port->type].fcr;
-		if (baud < 2400) {
+		if (baud < 2400 || fifo_bug) {
 			fcr &= ~UART_FCR_TRIGGER_MASK;
 			fcr |= UART_FCR_TRIGGER_1;
 		}
@@ -2336,7 +2340,7 @@
 			serial_port_out(port, UART_EFR, efr);
 	}
 
-#ifdef CONFIG_ARCH_OMAP
+#ifdef CONFIG_ARCH_OMAP1
 	/* Workaround to enable 115200 baud on OMAP1510 internal ports */
 	if (cpu_is_omap1510() && is_omap_port(up)) {
 		if (baud == 115200) {
@@ -2426,7 +2430,7 @@
 {
 	if (pt->port.iotype == UPIO_AU)
 		return 0x1000;
-#ifdef CONFIG_ARCH_OMAP
+#ifdef CONFIG_ARCH_OMAP1
 	if (is_omap_port(pt))
 		return 0x16 << pt->port.regshift;
 #endif
@@ -2979,36 +2983,36 @@
 static int __devinit serial8250_probe(struct platform_device *dev)
 {
 	struct plat_serial8250_port *p = dev->dev.platform_data;
-	struct uart_port port;
+	struct uart_8250_port uart;
 	int ret, i, irqflag = 0;
 
-	memset(&port, 0, sizeof(struct uart_port));
+	memset(&uart, 0, sizeof(uart));
 
 	if (share_irqs)
 		irqflag = IRQF_SHARED;
 
 	for (i = 0; p && p->flags != 0; p++, i++) {
-		port.iobase		= p->iobase;
-		port.membase		= p->membase;
-		port.irq		= p->irq;
-		port.irqflags		= p->irqflags;
-		port.uartclk		= p->uartclk;
-		port.regshift		= p->regshift;
-		port.iotype		= p->iotype;
-		port.flags		= p->flags;
-		port.mapbase		= p->mapbase;
-		port.hub6		= p->hub6;
-		port.private_data	= p->private_data;
-		port.type		= p->type;
-		port.serial_in		= p->serial_in;
-		port.serial_out		= p->serial_out;
-		port.handle_irq		= p->handle_irq;
-		port.handle_break	= p->handle_break;
-		port.set_termios	= p->set_termios;
-		port.pm			= p->pm;
-		port.dev		= &dev->dev;
-		port.irqflags		|= irqflag;
-		ret = serial8250_register_port(&port);
+		uart.port.iobase	= p->iobase;
+		uart.port.membase	= p->membase;
+		uart.port.irq		= p->irq;
+		uart.port.irqflags	= p->irqflags;
+		uart.port.uartclk	= p->uartclk;
+		uart.port.regshift	= p->regshift;
+		uart.port.iotype	= p->iotype;
+		uart.port.flags		= p->flags;
+		uart.port.mapbase	= p->mapbase;
+		uart.port.hub6		= p->hub6;
+		uart.port.private_data	= p->private_data;
+		uart.port.type		= p->type;
+		uart.port.serial_in	= p->serial_in;
+		uart.port.serial_out	= p->serial_out;
+		uart.port.handle_irq	= p->handle_irq;
+		uart.port.handle_break	= p->handle_break;
+		uart.port.set_termios	= p->set_termios;
+		uart.port.pm		= p->pm;
+		uart.port.dev		= &dev->dev;
+		uart.port.irqflags	|= irqflag;
+		ret = serial8250_register_8250_port(&uart);
 		if (ret < 0) {
 			dev_err(&dev->dev, "unable to register port at index %d "
 				"(IO%lx MEM%llx IRQ%d): %d\n", i,
@@ -3081,7 +3085,7 @@
 static struct platform_device *serial8250_isa_devs;
 
 /*
- * serial8250_register_port and serial8250_unregister_port allows for
+ * serial8250_register_8250_port and serial8250_unregister_port allows for
  * 16x50 serial ports to be configured at run-time, to support PCMCIA
  * modems and PCI multiport cards.
  */
@@ -3155,6 +3159,7 @@
 		uart->port.regshift     = up->port.regshift;
 		uart->port.iotype       = up->port.iotype;
 		uart->port.flags        = up->port.flags | UPF_BOOT_AUTOCONF;
+		uart->bugs		= up->bugs;
 		uart->port.mapbase      = up->port.mapbase;
 		uart->port.private_data = up->port.private_data;
 		if (up->port.dev)
@@ -3198,29 +3203,6 @@
 EXPORT_SYMBOL(serial8250_register_8250_port);
 
 /**
- *	serial8250_register_port - register a serial port
- *	@port: serial port template
- *
- *	Configure the serial port specified by the request. If the
- *	port exists and is in use, it is hung up and unregistered
- *	first.
- *
- *	The port is then probed and if necessary the IRQ is autodetected
- *	If this fails an error is returned.
- *
- *	On success the port is ready to use and the line number is returned.
- */
-int serial8250_register_port(struct uart_port *port)
-{
-	struct uart_8250_port up;
-
-	memset(&up, 0, sizeof(up));
-	memcpy(&up.port, port, sizeof(*port));
-	return serial8250_register_8250_port(&up);
-}
-EXPORT_SYMBOL(serial8250_register_port);
-
-/**
  *	serial8250_unregister_port - remove a 16x50 serial port at runtime
  *	@line: serial line number
  *
diff --git a/drivers/tty/serial/8250/8250.h b/drivers/tty/serial/8250/8250.h
index f9719d1..0c5e908 100644
--- a/drivers/tty/serial/8250/8250.h
+++ b/drivers/tty/serial/8250/8250.h
@@ -13,36 +13,6 @@
 
 #include <linux/serial_8250.h>
 
-struct uart_8250_port {
-	struct uart_port	port;
-	struct timer_list	timer;		/* "no irq" timer */
-	struct list_head	list;		/* ports on this IRQ */
-	unsigned short		capabilities;	/* port capabilities */
-	unsigned short		bugs;		/* port bugs */
-	unsigned int		tx_loadsz;	/* transmit fifo load size */
-	unsigned char		acr;
-	unsigned char		ier;
-	unsigned char		lcr;
-	unsigned char		mcr;
-	unsigned char		mcr_mask;	/* mask of user bits */
-	unsigned char		mcr_force;	/* mask of forced bits */
-	unsigned char		cur_iotype;	/* Running I/O type */
-
-	/*
-	 * Some bits in registers are cleared on a read, so they must
-	 * be saved whenever the register is read but the bits will not
-	 * be immediately processed.
-	 */
-#define LSR_SAVE_FLAGS UART_LSR_BRK_ERROR_BITS
-	unsigned char		lsr_saved_flags;
-#define MSR_SAVE_FLAGS UART_MSR_ANY_DELTA
-	unsigned char		msr_saved_flags;
-
-	/* 8250 specific callbacks */
-	int			(*dl_read)(struct uart_8250_port *);
-	void			(*dl_write)(struct uart_8250_port *, int);
-};
-
 struct old_serial_port {
 	unsigned int uart;
 	unsigned int baud_base;
@@ -56,9 +26,6 @@
 	unsigned long irqflags;
 };
 
-/*
- * This replaces serial_uart_config in include/linux/serial.h
- */
 struct serial8250_config {
 	const char	*name;
 	unsigned short	fifo_size;
@@ -78,6 +45,7 @@
 #define UART_BUG_TXEN	(1 << 1)	/* UART has buggy TX IIR status */
 #define UART_BUG_NOMSR	(1 << 2)	/* UART has buggy MSR status bits (Au1x00) */
 #define UART_BUG_THRE	(1 << 3)	/* UART has buggy THRE reassertion */
+#define UART_BUG_PARITY	(1 << 4)	/* UART mishandles parity if FIFO enabled */
 
 #define PROBE_RSA	(1 << 0)
 #define PROBE_ANY	(~0)
diff --git a/drivers/tty/serial/8250/8250_acorn.c b/drivers/tty/serial/8250/8250_acorn.c
index b0ce8c5..8574983 100644
--- a/drivers/tty/serial/8250/8250_acorn.c
+++ b/drivers/tty/serial/8250/8250_acorn.c
@@ -43,7 +43,7 @@
 {
 	struct serial_card_info *info;
 	struct serial_card_type *type = id->data;
-	struct uart_port port;
+	struct uart_8250_port uart;
 	unsigned long bus_addr;
 	unsigned int i;
 
@@ -62,19 +62,19 @@
 
 	ecard_set_drvdata(ec, info);
 
-	memset(&port, 0, sizeof(struct uart_port));
-	port.irq	= ec->irq;
-	port.flags	= UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ;
-	port.uartclk	= type->uartclk;
-	port.iotype	= UPIO_MEM;
-	port.regshift	= 2;
-	port.dev	= &ec->dev;
+	memset(&uart, 0, sizeof(struct uart_8250_port));
+	uart.port.irq	= ec->irq;
+	uart.port.flags	= UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ;
+	uart.port.uartclk	= type->uartclk;
+	uart.port.iotype	= UPIO_MEM;
+	uart.port.regshift	= 2;
+	uart.port.dev	= &ec->dev;
 
 	for (i = 0; i < info->num_ports; i ++) {
-		port.membase = info->vaddr + type->offset[i];
-		port.mapbase = bus_addr + type->offset[i];
+		uart.port.membase = info->vaddr + type->offset[i];
+		uart.port.mapbase = bus_addr + type->offset[i];
 
-		info->ports[i] = serial8250_register_port(&port);
+		info->ports[i] = serial8250_register_8250_port(&uart);
 	}
 
 	return 0;
diff --git a/drivers/tty/serial/8250/8250_dw.c b/drivers/tty/serial/8250/8250_dw.c
index f574eef..c3b2ec0 100644
--- a/drivers/tty/serial/8250/8250_dw.c
+++ b/drivers/tty/serial/8250/8250_dw.c
@@ -89,7 +89,7 @@
 
 static int __devinit dw8250_probe(struct platform_device *pdev)
 {
-	struct uart_port port = {};
+	struct uart_8250_port uart = {};
 	struct resource *regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	struct resource *irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
 	struct device_node *np = pdev->dev.of_node;
@@ -104,28 +104,28 @@
 	data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
 	if (!data)
 		return -ENOMEM;
-	port.private_data = data;
+	uart.port.private_data = data;
 
-	spin_lock_init(&port.lock);
-	port.mapbase = regs->start;
-	port.irq = irq->start;
-	port.handle_irq = dw8250_handle_irq;
-	port.type = PORT_8250;
-	port.flags = UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF | UPF_IOREMAP |
+	spin_lock_init(&uart.port.lock);
+	uart.port.mapbase = regs->start;
+	uart.port.irq = irq->start;
+	uart.port.handle_irq = dw8250_handle_irq;
+	uart.port.type = PORT_8250;
+	uart.port.flags = UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF | UPF_IOREMAP |
 		UPF_FIXED_PORT | UPF_FIXED_TYPE;
-	port.dev = &pdev->dev;
+	uart.port.dev = &pdev->dev;
 
-	port.iotype = UPIO_MEM;
-	port.serial_in = dw8250_serial_in;
-	port.serial_out = dw8250_serial_out;
+	uart.port.iotype = UPIO_MEM;
+	uart.port.serial_in = dw8250_serial_in;
+	uart.port.serial_out = dw8250_serial_out;
 	if (!of_property_read_u32(np, "reg-io-width", &val)) {
 		switch (val) {
 		case 1:
 			break;
 		case 4:
-			port.iotype = UPIO_MEM32;
-			port.serial_in = dw8250_serial_in32;
-			port.serial_out = dw8250_serial_out32;
+			uart.port.iotype = UPIO_MEM32;
+			uart.port.serial_in = dw8250_serial_in32;
+			uart.port.serial_out = dw8250_serial_out32;
 			break;
 		default:
 			dev_err(&pdev->dev, "unsupported reg-io-width (%u)\n",
@@ -135,15 +135,15 @@
 	}
 
 	if (!of_property_read_u32(np, "reg-shift", &val))
-		port.regshift = val;
+		uart.port.regshift = val;
 
 	if (of_property_read_u32(np, "clock-frequency", &val)) {
 		dev_err(&pdev->dev, "no clock-frequency property set\n");
 		return -EINVAL;
 	}
-	port.uartclk = val;
+	uart.port.uartclk = val;
 
-	data->line = serial8250_register_port(&port);
+	data->line = serial8250_register_8250_port(&uart);
 	if (data->line < 0)
 		return data->line;
 
diff --git a/drivers/tty/serial/8250/8250_gsc.c b/drivers/tty/serial/8250/8250_gsc.c
index d8c0ffb..097dff9 100644
--- a/drivers/tty/serial/8250/8250_gsc.c
+++ b/drivers/tty/serial/8250/8250_gsc.c
@@ -26,7 +26,7 @@
 
 static int __init serial_init_chip(struct parisc_device *dev)
 {
-	struct uart_port port;
+	struct uart_8250_port uart;
 	unsigned long address;
 	int err;
 
@@ -48,21 +48,21 @@
 	if (dev->id.sversion != 0x8d)
 		address += 0x800;
 
-	memset(&port, 0, sizeof(port));
-	port.iotype	= UPIO_MEM;
+	memset(&uart, 0, sizeof(uart));
+	uart.port.iotype	= UPIO_MEM;
 	/* 7.272727MHz on Lasi.  Assumed the same for Dino, Wax and Timi. */
-	port.uartclk	= 7272727;
-	port.mapbase	= address;
-	port.membase	= ioremap_nocache(address, 16);
-	port.irq	= dev->irq;
-	port.flags	= UPF_BOOT_AUTOCONF;
-	port.dev	= &dev->dev;
+	uart.port.uartclk	= 7272727;
+	uart.port.mapbase	= address;
+	uart.port.membase	= ioremap_nocache(address, 16);
+	uart.port.irq	= dev->irq;
+	uart.port.flags	= UPF_BOOT_AUTOCONF;
+	uart.port.dev	= &dev->dev;
 
-	err = serial8250_register_port(&port);
+	err = serial8250_register_8250_port(&uart);
 	if (err < 0) {
 		printk(KERN_WARNING
-			"serial8250_register_port returned error %d\n", err);
-		iounmap(port.membase);
+			"serial8250_register_8250_port returned error %d\n", err);
+		iounmap(uart.port.membase);
 		return err;
 	}
 
diff --git a/drivers/tty/serial/8250/8250_hp300.c b/drivers/tty/serial/8250/8250_hp300.c
index c13438c..8f1dd2c 100644
--- a/drivers/tty/serial/8250/8250_hp300.c
+++ b/drivers/tty/serial/8250/8250_hp300.c
@@ -171,7 +171,7 @@
 		return 0;
 	}
 #endif
-	memset(&port, 0, sizeof(struct uart_port));
+	memset(&uart, 0, sizeof(uart));
 
 	/* Memory mapped I/O */
 	port.iotype = UPIO_MEM;
@@ -182,7 +182,7 @@
 	port.membase = (char *)(port.mapbase + DIO_VIRADDRBASE);
 	port.regshift = 1;
 	port.dev = &d->dev;
-	line = serial8250_register_port(&port);
+	line = serial8250_register_8250_port(&uart);
 
 	if (line < 0) {
 		printk(KERN_NOTICE "8250_hp300: register_serial() DCA scode %d"
@@ -210,7 +210,7 @@
 #ifdef CONFIG_HPAPCI
 	int line;
 	unsigned long base;
-	struct uart_port uport;
+	struct uart_8250_port uart;
 	struct hp300_port *port;
 	int i;
 #endif
@@ -248,26 +248,26 @@
 		if (!port)
 			return -ENOMEM;
 
-		memset(&uport, 0, sizeof(struct uart_port));
+		memset(&uart, 0, sizeof(uart));
 
 		base = (FRODO_BASE + FRODO_APCI_OFFSET(i));
 
 		/* Memory mapped I/O */
-		uport.iotype = UPIO_MEM;
-		uport.flags = UPF_SKIP_TEST | UPF_SHARE_IRQ \
+		uart.port.iotype = UPIO_MEM;
+		uart.port.flags = UPF_SKIP_TEST | UPF_SHARE_IRQ \
 			      | UPF_BOOT_AUTOCONF;
 		/* XXX - no interrupt support yet */
-		uport.irq = 0;
-		uport.uartclk = HPAPCI_BAUD_BASE * 16;
-		uport.mapbase = base;
-		uport.membase = (char *)(base + DIO_VIRADDRBASE);
-		uport.regshift = 2;
+		uart.port.irq = 0;
+		uart.port.uartclk = HPAPCI_BAUD_BASE * 16;
+		uart.port.mapbase = base;
+		uart.port.membase = (char *)(base + DIO_VIRADDRBASE);
+		uart.port.regshift = 2;
 
-		line = serial8250_register_port(&uport);
+		line = serial8250_register_8250_port(&uart);
 
 		if (line < 0) {
 			printk(KERN_NOTICE "8250_hp300: register_serial() APCI"
-			       " %d irq %d failed\n", i, uport.irq);
+			       " %d irq %d failed\n", i, uart.port.irq);
 			kfree(port);
 			continue;
 		}
diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
index 28e7c7c..fdab80a 100644
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -44,7 +44,7 @@
 	int	(*init)(struct pci_dev *dev);
 	int	(*setup)(struct serial_private *,
 			 const struct pciserial_board *,
-			 struct uart_port *, int);
+			 struct uart_8250_port *, int);
 	void	(*exit)(struct pci_dev *dev);
 };
 
@@ -59,7 +59,7 @@
 };
 
 static int pci_default_setup(struct serial_private*,
-	  const struct pciserial_board*, struct uart_port*, int);
+	  const struct pciserial_board*, struct uart_8250_port *, int);
 
 static void moan_device(const char *str, struct pci_dev *dev)
 {
@@ -74,7 +74,7 @@
 }
 
 static int
-setup_port(struct serial_private *priv, struct uart_port *port,
+setup_port(struct serial_private *priv, struct uart_8250_port *port,
 	   int bar, int offset, int regshift)
 {
 	struct pci_dev *dev = priv->dev;
@@ -93,17 +93,17 @@
 		if (!priv->remapped_bar[bar])
 			return -ENOMEM;
 
-		port->iotype = UPIO_MEM;
-		port->iobase = 0;
-		port->mapbase = base + offset;
-		port->membase = priv->remapped_bar[bar] + offset;
-		port->regshift = regshift;
+		port->port.iotype = UPIO_MEM;
+		port->port.iobase = 0;
+		port->port.mapbase = base + offset;
+		port->port.membase = priv->remapped_bar[bar] + offset;
+		port->port.regshift = regshift;
 	} else {
-		port->iotype = UPIO_PORT;
-		port->iobase = base + offset;
-		port->mapbase = 0;
-		port->membase = NULL;
-		port->regshift = 0;
+		port->port.iotype = UPIO_PORT;
+		port->port.iobase = base + offset;
+		port->port.mapbase = 0;
+		port->port.membase = NULL;
+		port->port.regshift = 0;
 	}
 	return 0;
 }
@@ -113,7 +113,7 @@
  */
 static int addidata_apci7800_setup(struct serial_private *priv,
 				const struct pciserial_board *board,
-				struct uart_port *port, int idx)
+				struct uart_8250_port *port, int idx)
 {
 	unsigned int bar = 0, offset = board->first_offset;
 	bar = FL_GET_BASE(board->flags);
@@ -140,7 +140,7 @@
  */
 static int
 afavlab_setup(struct serial_private *priv, const struct pciserial_board *board,
-	      struct uart_port *port, int idx)
+	      struct uart_8250_port *port, int idx)
 {
 	unsigned int bar, offset = board->first_offset;
 
@@ -195,7 +195,7 @@
 static int
 pci_hp_diva_setup(struct serial_private *priv,
 		const struct pciserial_board *board,
-		struct uart_port *port, int idx)
+		struct uart_8250_port *port, int idx)
 {
 	unsigned int offset = board->first_offset;
 	unsigned int bar = FL_GET_BASE(board->flags);
@@ -370,7 +370,7 @@
 /* SBS Technologies Inc. PMC-OCTPRO and P-OCTAL cards */
 static int
 sbs_setup(struct serial_private *priv, const struct pciserial_board *board,
-		struct uart_port *port, int idx)
+		struct uart_8250_port *port, int idx)
 {
 	unsigned int bar, offset = board->first_offset;
 
@@ -525,7 +525,7 @@
 
 static int pci_siig_setup(struct serial_private *priv,
 			  const struct pciserial_board *board,
-			  struct uart_port *port, int idx)
+			  struct uart_8250_port *port, int idx)
 {
 	unsigned int bar = FL_GET_BASE(board->flags) + idx, offset = 0;
 
@@ -619,7 +619,7 @@
 static int
 pci_timedia_setup(struct serial_private *priv,
 		  const struct pciserial_board *board,
-		  struct uart_port *port, int idx)
+		  struct uart_8250_port *port, int idx)
 {
 	unsigned int bar = 0, offset = board->first_offset;
 
@@ -653,7 +653,7 @@
 static int
 titan_400l_800l_setup(struct serial_private *priv,
 		      const struct pciserial_board *board,
-		      struct uart_port *port, int idx)
+		      struct uart_8250_port *port, int idx)
 {
 	unsigned int bar, offset = board->first_offset;
 
@@ -754,7 +754,7 @@
 static int
 pci_ni8430_setup(struct serial_private *priv,
 		 const struct pciserial_board *board,
-		 struct uart_port *port, int idx)
+		 struct uart_8250_port *port, int idx)
 {
 	void __iomem *p;
 	unsigned long base, len;
@@ -781,7 +781,7 @@
 
 static int pci_netmos_9900_setup(struct serial_private *priv,
 				const struct pciserial_board *board,
-				struct uart_port *port, int idx)
+				struct uart_8250_port *port, int idx)
 {
 	unsigned int bar;
 
@@ -1032,10 +1032,17 @@
 	return number_uarts;
 }
 
-static int
-pci_default_setup(struct serial_private *priv,
+static int pci_asix_setup(struct serial_private *priv,
 		  const struct pciserial_board *board,
-		  struct uart_port *port, int idx)
+		  struct uart_8250_port *port, int idx)
+{
+	port->bugs |= UART_BUG_PARITY;
+	return pci_default_setup(priv, board, port, idx);
+}
+
+static int pci_default_setup(struct serial_private *priv,
+		  const struct pciserial_board *board,
+		  struct uart_8250_port *port, int idx)
 {
 	unsigned int bar, offset = board->first_offset, maxnr;
 
@@ -1057,15 +1064,15 @@
 static int
 ce4100_serial_setup(struct serial_private *priv,
 		  const struct pciserial_board *board,
-		  struct uart_port *port, int idx)
+		  struct uart_8250_port *port, int idx)
 {
 	int ret;
 
 	ret = setup_port(priv, port, 0, 0, board->reg_shift);
-	port->iotype = UPIO_MEM32;
-	port->type = PORT_XSCALE;
-	port->flags = (port->flags | UPF_FIXED_PORT | UPF_FIXED_TYPE);
-	port->regshift = 2;
+	port->port.iotype = UPIO_MEM32;
+	port->port.type = PORT_XSCALE;
+	port->port.flags = (port->port.flags | UPF_FIXED_PORT | UPF_FIXED_TYPE);
+	port->port.regshift = 2;
 
 	return ret;
 }
@@ -1073,16 +1080,16 @@
 static int
 pci_omegapci_setup(struct serial_private *priv,
 		      const struct pciserial_board *board,
-		      struct uart_port *port, int idx)
+		      struct uart_8250_port *port, int idx)
 {
 	return setup_port(priv, port, 2, idx * 8, 0);
 }
 
 static int skip_tx_en_setup(struct serial_private *priv,
 			const struct pciserial_board *board,
-			struct uart_port *port, int idx)
+			struct uart_8250_port *port, int idx)
 {
-	port->flags |= UPF_NO_TXEN_TEST;
+	port->port.flags |= UPF_NO_TXEN_TEST;
 	printk(KERN_DEBUG "serial8250: skipping TxEn test for device "
 			  "[%04x:%04x] subsystem [%04x:%04x]\n",
 			  priv->dev->vendor,
@@ -1131,11 +1138,11 @@
 
 static int kt_serial_setup(struct serial_private *priv,
 			   const struct pciserial_board *board,
-			   struct uart_port *port, int idx)
+			   struct uart_8250_port *port, int idx)
 {
-	port->flags |= UPF_BUG_THRE;
-	port->serial_in = kt_serial_in;
-	port->handle_break = kt_handle_break;
+	port->port.flags |= UPF_BUG_THRE;
+	port->port.serial_in = kt_serial_in;
+	port->port.handle_break = kt_handle_break;
 	return skip_tx_en_setup(priv, board, port, idx);
 }
 
@@ -1151,9 +1158,19 @@
 static int
 pci_xr17c154_setup(struct serial_private *priv,
 		  const struct pciserial_board *board,
-		  struct uart_port *port, int idx)
+		  struct uart_8250_port *port, int idx)
 {
-	port->flags |= UPF_EXAR_EFR;
+	port->port.flags |= UPF_EXAR_EFR;
+	return pci_default_setup(priv, board, port, idx);
+}
+
+static int
+pci_wch_ch353_setup(struct serial_private *priv,
+                    const struct pciserial_board *board,
+                    struct uart_8250_port *port, int idx)
+{
+	port->port.flags |= UPF_FIXED_TYPE;
+	port->port.type = PORT_16550A;
 	return pci_default_setup(priv, board, port, idx);
 }
 
@@ -1187,6 +1204,13 @@
 #define PCIE_DEVICE_ID_NEO_2_OX_IBM	0x00F6
 #define PCI_DEVICE_ID_PLX_CRONYX_OMEGA	0xc001
 #define PCI_DEVICE_ID_INTEL_PATSBURG_KT 0x1d3d
+#define PCI_VENDOR_ID_WCH		0x4348
+#define PCI_DEVICE_ID_WCH_CH353_4S	0x3453
+#define PCI_DEVICE_ID_WCH_CH353_2S1PF	0x5046
+#define PCI_DEVICE_ID_WCH_CH353_2S1P	0x7053
+#define PCI_VENDOR_ID_AGESTAR		0x5372
+#define PCI_DEVICE_ID_AGESTAR_9375	0x6872
+#define PCI_VENDOR_ID_ASIX		0x9710
 
 /* Unknown vendors/cards - this should not be in linux/pci_ids.h */
 #define PCI_SUBDEVICE_ID_UNKNOWN_0x1584	0x1584
@@ -1726,7 +1750,41 @@
 		.subvendor	= PCI_ANY_ID,
 		.subdevice	= PCI_ANY_ID,
 		.setup		= pci_omegapci_setup,
-	 },
+	},
+	/* WCH CH353 2S1P card (16550 clone) */
+	{
+		.vendor         = PCI_VENDOR_ID_WCH,
+		.device         = PCI_DEVICE_ID_WCH_CH353_2S1P,
+		.subvendor      = PCI_ANY_ID,
+		.subdevice      = PCI_ANY_ID,
+		.setup          = pci_wch_ch353_setup,
+	},
+	/* WCH CH353 4S card (16550 clone) */
+	{
+		.vendor         = PCI_VENDOR_ID_WCH,
+		.device         = PCI_DEVICE_ID_WCH_CH353_4S,
+		.subvendor      = PCI_ANY_ID,
+		.subdevice      = PCI_ANY_ID,
+		.setup          = pci_wch_ch353_setup,
+	},
+	/* WCH CH353 2S1PF card (16550 clone) */
+	{
+		.vendor         = PCI_VENDOR_ID_WCH,
+		.device         = PCI_DEVICE_ID_WCH_CH353_2S1PF,
+		.subvendor      = PCI_ANY_ID,
+		.subdevice      = PCI_ANY_ID,
+		.setup          = pci_wch_ch353_setup,
+	},
+	/*
+	 * ASIX devices with FIFO bug
+	 */
+	{
+		.vendor		= PCI_VENDOR_ID_ASIX,
+		.device		= PCI_ANY_ID,
+		.subvendor	= PCI_ANY_ID,
+		.subdevice	= PCI_ANY_ID,
+		.setup		= pci_asix_setup,
+	},
 	/*
 	 * Default "match everything" terminator entry
 	 */
@@ -1887,7 +1945,6 @@
 	pbn_panacom,
 	pbn_panacom2,
 	pbn_panacom4,
-	pbn_exsys_4055,
 	pbn_plx_romulus,
 	pbn_oxsemi,
 	pbn_oxsemi_1_4000000,
@@ -2393,13 +2450,6 @@
 		.reg_shift	= 7,
 	},
 
-	[pbn_exsys_4055] = {
-		.flags		= FL_BASE2,
-		.num_ports	= 4,
-		.base_baud	= 115200,
-		.uart_offset	= 8,
-	},
-
 	/* I think this entry is broken - the first_offset looks wrong --rmk */
 	[pbn_plx_romulus] = {
 		.flags		= FL_BASE2,
@@ -2624,10 +2674,14 @@
 	},
 };
 
-static const struct pci_device_id softmodem_blacklist[] = {
+static const struct pci_device_id blacklist[] = {
+	/* softmodems */
 	{ PCI_VDEVICE(AL, 0x5457), }, /* ALi Corporation M5457 AC'97 Modem */
 	{ PCI_VDEVICE(MOTOROLA, 0x3052), }, /* Motorola Si3052-based modem */
 	{ PCI_DEVICE(0x1543, 0x3052), }, /* Si3052-based modem, default IDs */
+
+	/* multi-io cards handled by parport_serial */
+	{ PCI_DEVICE(0x4348, 0x7053), }, /* WCH CH353 2S1P */
 };
 
 /*
@@ -2638,7 +2692,7 @@
 static int __devinit
 serial_pci_guess_board(struct pci_dev *dev, struct pciserial_board *board)
 {
-	const struct pci_device_id *blacklist;
+	const struct pci_device_id *bldev;
 	int num_iomem, num_port, first_port = -1, i;
 
 	/*
@@ -2655,13 +2709,13 @@
 
 	/*
 	 * Do not access blacklisted devices that are known not to
-	 * feature serial ports.
+	 * feature serial ports or are handled by other modules.
 	 */
-	for (blacklist = softmodem_blacklist;
-	     blacklist < softmodem_blacklist + ARRAY_SIZE(softmodem_blacklist);
-	     blacklist++) {
-		if (dev->vendor == blacklist->vendor &&
-		    dev->device == blacklist->device)
+	for (bldev = blacklist;
+	     bldev < blacklist + ARRAY_SIZE(blacklist);
+	     bldev++) {
+		if (dev->vendor == bldev->vendor &&
+		    dev->device == bldev->device)
 			return -ENODEV;
 	}
 
@@ -2728,7 +2782,7 @@
 struct serial_private *
 pciserial_init_ports(struct pci_dev *dev, const struct pciserial_board *board)
 {
-	struct uart_port serial_port;
+	struct uart_8250_port uart;
 	struct serial_private *priv;
 	struct pci_serial_quirk *quirk;
 	int rc, nr_ports, i;
@@ -2768,22 +2822,22 @@
 	priv->dev = dev;
 	priv->quirk = quirk;
 
-	memset(&serial_port, 0, sizeof(struct uart_port));
-	serial_port.flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ;
-	serial_port.uartclk = board->base_baud * 16;
-	serial_port.irq = get_pci_irq(dev, board);
-	serial_port.dev = &dev->dev;
+	memset(&uart, 0, sizeof(uart));
+	uart.port.flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ;
+	uart.port.uartclk = board->base_baud * 16;
+	uart.port.irq = get_pci_irq(dev, board);
+	uart.port.dev = &dev->dev;
 
 	for (i = 0; i < nr_ports; i++) {
-		if (quirk->setup(priv, board, &serial_port, i))
+		if (quirk->setup(priv, board, &uart, i))
 			break;
 
 #ifdef SERIAL_DEBUG_PCI
 		printk(KERN_DEBUG "Setup PCI port: port %lx, irq %d, type %d\n",
-		       serial_port.iobase, serial_port.irq, serial_port.iotype);
+		       uart.port.iobase, uart.port.irq, uart.port.iotype);
 #endif
 
-		priv->line[i] = serial8250_register_port(&serial_port);
+		priv->line[i] = serial8250_register_8250_port(&uart);
 		if (priv->line[i] < 0) {
 			printk(KERN_WARNING "Couldn't register serial port %s: %d\n", pci_name(dev), priv->line[i]);
 			break;
@@ -3193,7 +3247,7 @@
 	{	PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
 		PCI_SUBVENDOR_ID_EXSYS,
 		PCI_SUBDEVICE_ID_EXSYS_4055, 0, 0,
-		pbn_exsys_4055 },
+		pbn_b2_4_115200 },
 	/*
 	 * Megawolf Romulus PCI Serial Card, from Mike Hudson
 	 * (Exoray@isys.ca)
@@ -4179,6 +4233,25 @@
 		pbn_omegapci },
 
 	/*
+	 * AgeStar as-prs2-009
+	 */
+	{	PCI_VENDOR_ID_AGESTAR, PCI_DEVICE_ID_AGESTAR_9375,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0, pbn_b0_bt_2_115200 },
+
+	/*
+	 * WCH CH353 series devices: The 2S1P is handled by parport_serial
+	 * so not listed here.
+	 */
+	{	PCI_VENDOR_ID_WCH, PCI_DEVICE_ID_WCH_CH353_4S,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0, pbn_b0_bt_4_115200 },
+
+	{	PCI_VENDOR_ID_WCH, PCI_DEVICE_ID_WCH_CH353_2S1PF,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0, pbn_b0_bt_2_115200 },
+
+	/*
 	 * These entries match devices with class COMMUNICATION_SERIAL,
 	 * COMMUNICATION_MODEM or COMMUNICATION_MULTISERIAL
 	 */
diff --git a/drivers/tty/serial/8250/8250_pnp.c b/drivers/tty/serial/8250/8250_pnp.c
index a2f2365..fde5aa6 100644
--- a/drivers/tty/serial/8250/8250_pnp.c
+++ b/drivers/tty/serial/8250/8250_pnp.c
@@ -424,7 +424,7 @@
 static int __devinit
 serial_pnp_probe(struct pnp_dev *dev, const struct pnp_device_id *dev_id)
 {
-	struct uart_port port;
+	struct uart_8250_port uart;
 	int ret, line, flags = dev_id->driver_data;
 
 	if (flags & UNKNOWN_DEV) {
@@ -433,32 +433,32 @@
 			return ret;
 	}
 
-	memset(&port, 0, sizeof(struct uart_port));
+	memset(&uart, 0, sizeof(uart));
 	if (pnp_irq_valid(dev, 0))
-		port.irq = pnp_irq(dev, 0);
+		uart.port.irq = pnp_irq(dev, 0);
 	if (pnp_port_valid(dev, 0)) {
-		port.iobase = pnp_port_start(dev, 0);
-		port.iotype = UPIO_PORT;
+		uart.port.iobase = pnp_port_start(dev, 0);
+		uart.port.iotype = UPIO_PORT;
 	} else if (pnp_mem_valid(dev, 0)) {
-		port.mapbase = pnp_mem_start(dev, 0);
-		port.iotype = UPIO_MEM;
-		port.flags = UPF_IOREMAP;
+		uart.port.mapbase = pnp_mem_start(dev, 0);
+		uart.port.iotype = UPIO_MEM;
+		uart.port.flags = UPF_IOREMAP;
 	} else
 		return -ENODEV;
 
 #ifdef SERIAL_DEBUG_PNP
 	printk(KERN_DEBUG
 		"Setup PNP port: port %x, mem 0x%lx, irq %d, type %d\n",
-		       port.iobase, port.mapbase, port.irq, port.iotype);
+		       uart.port.iobase, uart.port.mapbase, uart.port.irq, uart.port.iotype);
 #endif
 
-	port.flags |= UPF_SKIP_TEST | UPF_BOOT_AUTOCONF;
+	uart.port.flags |= UPF_SKIP_TEST | UPF_BOOT_AUTOCONF;
 	if (pnp_irq_flags(dev, 0) & IORESOURCE_IRQ_SHAREABLE)
-		port.flags |= UPF_SHARE_IRQ;
-	port.uartclk = 1843200;
-	port.dev = &dev->dev;
+		uart.port.flags |= UPF_SHARE_IRQ;
+	uart.port.uartclk = 1843200;
+	uart.port.dev = &dev->dev;
 
-	line = serial8250_register_port(&port);
+	line = serial8250_register_8250_port(&uart);
 	if (line < 0)
 		return -ENODEV;
 
diff --git a/drivers/tty/serial/8250/serial_cs.c b/drivers/tty/serial/8250/serial_cs.c
index 29b695d..b7d48b3 100644
--- a/drivers/tty/serial/8250/serial_cs.c
+++ b/drivers/tty/serial/8250/serial_cs.c
@@ -73,7 +73,7 @@
 	unsigned int prodid;
 	int multi;		/* 1 = multifunction, > 1 = # ports */
 	void (*config)(struct pcmcia_device *);
-	void (*setup)(struct pcmcia_device *, struct uart_port *);
+	void (*setup)(struct pcmcia_device *, struct uart_8250_port *);
 	void (*wakeup)(struct pcmcia_device *);
 	int (*post)(struct pcmcia_device *);
 };
@@ -105,9 +105,9 @@
  * Elan VPU16551 UART with 14.7456MHz oscillator
  * manfid 0x015D, 0x4C45
  */
-static void quirk_setup_brainboxes_0104(struct pcmcia_device *link, struct uart_port *port)
+static void quirk_setup_brainboxes_0104(struct pcmcia_device *link, struct uart_8250_port *uart)
 {
-	port->uartclk = 14745600;
+	uart->port.uartclk = 14745600;
 }
 
 static int quirk_post_ibm(struct pcmcia_device *link)
@@ -343,25 +343,25 @@
 static int setup_serial(struct pcmcia_device *handle, struct serial_info * info,
 			unsigned int iobase, int irq)
 {
-	struct uart_port port;
+	struct uart_8250_port uart;
 	int line;
 
-	memset(&port, 0, sizeof (struct uart_port));
-	port.iobase = iobase;
-	port.irq = irq;
-	port.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_SHARE_IRQ;
-	port.uartclk = 1843200;
-	port.dev = &handle->dev;
+	memset(&uart, 0, sizeof(uart));
+	uart.port.iobase = iobase;
+	uart.port.irq = irq;
+	uart.port.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_SHARE_IRQ;
+	uart.port.uartclk = 1843200;
+	uart.port.dev = &handle->dev;
 	if (buggy_uart)
-		port.flags |= UPF_BUGGY_UART;
+		uart.port.flags |= UPF_BUGGY_UART;
 
 	if (info->quirk && info->quirk->setup)
-		info->quirk->setup(handle, &port);
+		info->quirk->setup(handle, &uart);
 
-	line = serial8250_register_port(&port);
+	line = serial8250_register_8250_port(&uart);
 	if (line < 0) {
-		printk(KERN_NOTICE "serial_cs: serial8250_register_port() at "
-		       "0x%04lx, irq %d failed\n", (u_long)iobase, irq);
+		pr_err("serial_cs: serial8250_register_8250_port() at 0x%04lx, irq %d failed\n",
+							(unsigned long)iobase, irq);
 		return -EINVAL;
 	}
 
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index 4720b4b..26907cf 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -257,12 +257,19 @@
 	help
 	  MAX3100 chip support
 
-config SERIAL_MAX3107
-	tristate "MAX3107 support"
+config SERIAL_MAX310X
+	bool "MAX310X support"
 	depends on SPI
 	select SERIAL_CORE
+	select REGMAP_SPI if SPI
+	default n
 	help
-	  MAX3107 chip support
+	  This selects support for an advanced UART from Maxim (Dallas).
+	  Supported ICs are MAX3107, MAX3108.
+	  Each IC contains 128 words each of receive and transmit FIFO
+	  that can be controlled through I2C or high-speed SPI.
+
+	  Say Y here if you want to support this ICs.
 
 config SERIAL_DZ
 	bool "DECstation DZ serial driver"
@@ -704,6 +711,25 @@
 	  If you have a MIPS-based Philips SoC such as PNX8550 or PNX8330
 	  and you want to use serial console, say Y. Otherwise, say N.
 
+config SERIAL_HS_LPC32XX
+	tristate "LPC32XX high speed serial port support"
+	depends on ARCH_LPC32XX && OF
+	select SERIAL_CORE
+	help
+	  Support for the LPC32XX high speed serial ports (up to 900kbps).
+	  Those are UARTs completely different from the Standard UARTs on the
+	  LPC32XX SoC.
+	  Choose M or Y here to build this driver.
+
+config SERIAL_HS_LPC32XX_CONSOLE
+	bool "Enable LPC32XX high speed UART serial console"
+	depends on SERIAL_HS_LPC32XX
+	select SERIAL_CORE_CONSOLE
+	help
+	  If you would like to be able to use one of the high speed serial
+	  ports on the LPC32XX as the console, you can do so by answering
+	  Y to this option.
+
 config SERIAL_CORE
 	tristate
 
@@ -1104,6 +1130,24 @@
 	help
 	  Support for Console on SC2681/SC2692 serial ports.
 
+config SERIAL_SCCNXP
+	bool "SCCNXP serial port support"
+	depends on !SERIAL_SC26XX
+	select SERIAL_CORE
+	default n
+	help
+	  This selects support for an advanced UART from NXP (Philips).
+	  Supported ICs are SCC2681, SCC2691, SCC2692, SC28L91, SC28L92,
+	  SC28L202, SCC68681 and SCC68692.
+	  Positioned as a replacement for the driver SC26XX.
+
+config SERIAL_SCCNXP_CONSOLE
+	bool "Console on SCCNXP serial port"
+	depends on SERIAL_SCCNXP
+	select SERIAL_CORE_CONSOLE
+	help
+	  Support for console on SCCNXP serial ports.
+
 config SERIAL_BFIN_SPORT
 	tristate "Blackfin SPORT emulate UART"
 	depends on BLACKFIN
diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile
index 7257c5d..ce88667 100644
--- a/drivers/tty/serial/Makefile
+++ b/drivers/tty/serial/Makefile
@@ -28,12 +28,13 @@
 obj-$(CONFIG_SERIAL_BFIN_SPORT) += bfin_sport_uart.o
 obj-$(CONFIG_SERIAL_SAMSUNG) += samsung.o
 obj-$(CONFIG_SERIAL_MAX3100) += max3100.o
-obj-$(CONFIG_SERIAL_MAX3107) += max3107.o
+obj-$(CONFIG_SERIAL_MAX310X) += max310x.o
 obj-$(CONFIG_SERIAL_IP22_ZILOG) += ip22zilog.o
 obj-$(CONFIG_SERIAL_MUX) += mux.o
 obj-$(CONFIG_SERIAL_68328) += 68328serial.o
 obj-$(CONFIG_SERIAL_MCF) += mcf.o
 obj-$(CONFIG_SERIAL_PMACZILOG) += pmac_zilog.o
+obj-$(CONFIG_SERIAL_HS_LPC32XX) += lpc32xx_hs.o
 obj-$(CONFIG_SERIAL_DZ) += dz.o
 obj-$(CONFIG_SERIAL_ZS) += zs.o
 obj-$(CONFIG_SERIAL_SH_SCI) += sh-sci.o
@@ -47,6 +48,7 @@
 obj-$(CONFIG_SERIAL_SB1250_DUART) += sb1250-duart.o
 obj-$(CONFIG_ETRAX_SERIAL) += crisv10.o
 obj-$(CONFIG_SERIAL_SC26XX) += sc26xx.o
+obj-$(CONFIG_SERIAL_SCCNXP) += sccnxp.o
 obj-$(CONFIG_SERIAL_JSM) += jsm/
 obj-$(CONFIG_SERIAL_TXX9) += serial_txx9.o
 obj-$(CONFIG_SERIAL_VR41XX) += vr41xx_siu.o
diff --git a/drivers/tty/serial/altera_uart.c b/drivers/tty/serial/altera_uart.c
index 1f03309..15d80b9 100644
--- a/drivers/tty/serial/altera_uart.c
+++ b/drivers/tty/serial/altera_uart.c
@@ -591,7 +591,7 @@
 	port->ops = &altera_uart_ops;
 	port->flags = UPF_BOOT_AUTOCONF;
 
-	dev_set_drvdata(&pdev->dev, port);
+	platform_set_drvdata(pdev, port);
 
 	uart_add_one_port(&altera_uart_driver, port);
 
@@ -600,11 +600,11 @@
 
 static int __devexit altera_uart_remove(struct platform_device *pdev)
 {
-	struct uart_port *port = dev_get_drvdata(&pdev->dev);
+	struct uart_port *port = platform_get_drvdata(pdev);
 
 	if (port) {
 		uart_remove_one_port(&altera_uart_driver, port);
-		dev_set_drvdata(&pdev->dev, NULL);
+		platform_set_drvdata(pdev, NULL);
 		port->mapbase = 0;
 	}
 
diff --git a/drivers/tty/serial/amba-pl010.c b/drivers/tty/serial/amba-pl010.c
index 0d91a54..22317dd 100644
--- a/drivers/tty/serial/amba-pl010.c
+++ b/drivers/tty/serial/amba-pl010.c
@@ -312,16 +312,12 @@
 	struct uart_amba_port *uap = (struct uart_amba_port *)port;
 	int retval;
 
-	retval = clk_prepare(uap->clk);
-	if (retval)
-		goto out;
-
 	/*
 	 * Try to enable the clock producer.
 	 */
-	retval = clk_enable(uap->clk);
+	retval = clk_prepare_enable(uap->clk);
 	if (retval)
-		goto clk_unprep;
+		goto out;
 
 	uap->port.uartclk = clk_get_rate(uap->clk);
 
@@ -346,9 +342,7 @@
 	return 0;
 
  clk_dis:
-	clk_disable(uap->clk);
- clk_unprep:
-	clk_unprepare(uap->clk);
+	clk_disable_unprepare(uap->clk);
  out:
 	return retval;
 }
@@ -375,8 +369,7 @@
 	/*
 	 * Shut down the clock producer
 	 */
-	clk_disable(uap->clk);
-	clk_unprepare(uap->clk);
+	clk_disable_unprepare(uap->clk);
 }
 
 static void
diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c
index d3553b5..cede938 100644
--- a/drivers/tty/serial/amba-pl011.c
+++ b/drivers/tty/serial/amba-pl011.c
@@ -52,6 +52,8 @@
 #include <linux/scatterlist.h>
 #include <linux/delay.h>
 #include <linux/types.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
 #include <linux/pinctrl/consumer.h>
 #include <linux/sizes.h>
 
@@ -75,7 +77,6 @@
 	unsigned int		lcrh_tx;
 	unsigned int		lcrh_rx;
 	bool			oversampling;
-	bool			interrupt_may_hang;   /* vendor-specific */
 	bool			dma_threshold;
 	bool			cts_event_workaround;
 };
@@ -96,7 +97,6 @@
 	.lcrh_tx		= ST_UART011_LCRH_TX,
 	.lcrh_rx		= ST_UART011_LCRH_RX,
 	.oversampling		= true,
-	.interrupt_may_hang	= true,
 	.dma_threshold		= true,
 	.cts_event_workaround	= true,
 };
@@ -147,7 +147,6 @@
 	unsigned int		old_cr;		/* state during shutdown */
 	bool			autorts;
 	char			type[12];
-	bool			interrupt_may_hang; /* vendor-specific */
 #ifdef CONFIG_DMA_ENGINE
 	/* DMA stuff */
 	bool			using_tx_dma;
@@ -1215,14 +1214,14 @@
 	return IRQ_RETVAL(handled);
 }
 
-static unsigned int pl01x_tx_empty(struct uart_port *port)
+static unsigned int pl011_tx_empty(struct uart_port *port)
 {
 	struct uart_amba_port *uap = (struct uart_amba_port *)port;
 	unsigned int status = readw(uap->port.membase + UART01x_FR);
 	return status & (UART01x_FR_BUSY|UART01x_FR_TXFF) ? 0 : TIOCSER_TEMT;
 }
 
-static unsigned int pl01x_get_mctrl(struct uart_port *port)
+static unsigned int pl011_get_mctrl(struct uart_port *port)
 {
 	struct uart_amba_port *uap = (struct uart_amba_port *)port;
 	unsigned int result = 0;
@@ -1285,7 +1284,7 @@
 }
 
 #ifdef CONFIG_CONSOLE_POLL
-static int pl010_get_poll_char(struct uart_port *port)
+static int pl011_get_poll_char(struct uart_port *port)
 {
 	struct uart_amba_port *uap = (struct uart_amba_port *)port;
 	unsigned int status;
@@ -1297,7 +1296,7 @@
 	return readw(uap->port.membase + UART01x_DR);
 }
 
-static void pl010_put_poll_char(struct uart_port *port,
+static void pl011_put_poll_char(struct uart_port *port,
 			 unsigned char ch)
 {
 	struct uart_amba_port *uap = (struct uart_amba_port *)port;
@@ -1324,16 +1323,12 @@
 				"could not set default pins\n");
 	}
 
-	retval = clk_prepare(uap->clk);
-	if (retval)
-		goto out;
-
 	/*
 	 * Try to enable the clock producer.
 	 */
-	retval = clk_enable(uap->clk);
+	retval = clk_prepare_enable(uap->clk);
 	if (retval)
-		goto clk_unprep;
+		goto out;
 
 	uap->port.uartclk = clk_get_rate(uap->clk);
 
@@ -1411,9 +1406,7 @@
 	return 0;
 
  clk_dis:
-	clk_disable(uap->clk);
- clk_unprep:
-	clk_unprepare(uap->clk);
+	clk_disable_unprepare(uap->clk);
  out:
 	return retval;
 }
@@ -1473,8 +1466,7 @@
 	/*
 	 * Shut down the clock producer
 	 */
-	clk_disable(uap->clk);
-	clk_unprepare(uap->clk);
+	clk_disable_unprepare(uap->clk);
 	/* Optionally let pins go into sleep states */
 	if (!IS_ERR(uap->pins_sleep)) {
 		retval = pinctrl_select_state(uap->pinctrl, uap->pins_sleep);
@@ -1637,7 +1629,7 @@
 /*
  * Release the memory region(s) being used by 'port'
  */
-static void pl010_release_port(struct uart_port *port)
+static void pl011_release_port(struct uart_port *port)
 {
 	release_mem_region(port->mapbase, SZ_4K);
 }
@@ -1645,7 +1637,7 @@
 /*
  * Request the memory region(s) being used by 'port'
  */
-static int pl010_request_port(struct uart_port *port)
+static int pl011_request_port(struct uart_port *port)
 {
 	return request_mem_region(port->mapbase, SZ_4K, "uart-pl011")
 			!= NULL ? 0 : -EBUSY;
@@ -1654,18 +1646,18 @@
 /*
  * Configure/autoconfigure the port.
  */
-static void pl010_config_port(struct uart_port *port, int flags)
+static void pl011_config_port(struct uart_port *port, int flags)
 {
 	if (flags & UART_CONFIG_TYPE) {
 		port->type = PORT_AMBA;
-		pl010_request_port(port);
+		pl011_request_port(port);
 	}
 }
 
 /*
  * verify the new serial_struct (for TIOCSSERIAL).
  */
-static int pl010_verify_port(struct uart_port *port, struct serial_struct *ser)
+static int pl011_verify_port(struct uart_port *port, struct serial_struct *ser)
 {
 	int ret = 0;
 	if (ser->type != PORT_UNKNOWN && ser->type != PORT_AMBA)
@@ -1678,9 +1670,9 @@
 }
 
 static struct uart_ops amba_pl011_pops = {
-	.tx_empty	= pl01x_tx_empty,
+	.tx_empty	= pl011_tx_empty,
 	.set_mctrl	= pl011_set_mctrl,
-	.get_mctrl	= pl01x_get_mctrl,
+	.get_mctrl	= pl011_get_mctrl,
 	.stop_tx	= pl011_stop_tx,
 	.start_tx	= pl011_start_tx,
 	.stop_rx	= pl011_stop_rx,
@@ -1691,13 +1683,13 @@
 	.flush_buffer	= pl011_dma_flush_buffer,
 	.set_termios	= pl011_set_termios,
 	.type		= pl011_type,
-	.release_port	= pl010_release_port,
-	.request_port	= pl010_request_port,
-	.config_port	= pl010_config_port,
-	.verify_port	= pl010_verify_port,
+	.release_port	= pl011_release_port,
+	.request_port	= pl011_request_port,
+	.config_port	= pl011_config_port,
+	.verify_port	= pl011_verify_port,
 #ifdef CONFIG_CONSOLE_POLL
-	.poll_get_char = pl010_get_poll_char,
-	.poll_put_char = pl010_put_poll_char,
+	.poll_get_char = pl011_get_poll_char,
+	.poll_put_char = pl011_put_poll_char,
 #endif
 };
 
@@ -1869,6 +1861,38 @@
 	.cons			= AMBA_CONSOLE,
 };
 
+static int pl011_probe_dt_alias(int index, struct device *dev)
+{
+	struct device_node *np;
+	static bool seen_dev_with_alias = false;
+	static bool seen_dev_without_alias = false;
+	int ret = index;
+
+	if (!IS_ENABLED(CONFIG_OF))
+		return ret;
+
+	np = dev->of_node;
+	if (!np)
+		return ret;
+
+	ret = of_alias_get_id(np, "serial");
+	if (IS_ERR_VALUE(ret)) {
+		seen_dev_without_alias = true;
+		ret = index;
+	} else {
+		seen_dev_with_alias = true;
+		if (ret >= ARRAY_SIZE(amba_ports) || amba_ports[ret] != NULL) {
+			dev_warn(dev, "requested serial port %d  not available.\n", ret);
+			ret = index;
+		}
+	}
+
+	if (seen_dev_with_alias && seen_dev_without_alias)
+		dev_warn(dev, "aliased and non-aliased serial devices found in device tree. Serial port enumeration may be unpredictable.\n");
+
+	return ret;
+}
+
 static int pl011_probe(struct amba_device *dev, const struct amba_id *id)
 {
 	struct uart_amba_port *uap;
@@ -1891,6 +1915,8 @@
 		goto out;
 	}
 
+	i = pl011_probe_dt_alias(i, &dev->dev);
+
 	base = ioremap(dev->res.start, resource_size(&dev->res));
 	if (!base) {
 		ret = -ENOMEM;
@@ -1923,7 +1949,6 @@
 	uap->lcrh_tx = vendor->lcrh_tx;
 	uap->old_cr = 0;
 	uap->fifosize = vendor->fifosize;
-	uap->interrupt_may_hang = vendor->interrupt_may_hang;
 	uap->port.dev = &dev->dev;
 	uap->port.mapbase = dev->res.start;
 	uap->port.membase = base;
diff --git a/drivers/tty/serial/bfin_uart.c b/drivers/tty/serial/bfin_uart.c
index bd97db2..9242d56 100644
--- a/drivers/tty/serial/bfin_uart.c
+++ b/drivers/tty/serial/bfin_uart.c
@@ -182,7 +182,7 @@
 	 * To avoid losting RX interrupt, we reset IR function
 	 * before sending data.
 	 */
-	if (tty->termios->c_line == N_IRDA)
+	if (tty->termios.c_line == N_IRDA)
 		bfin_serial_reset_irda(port);
 
 #ifdef CONFIG_SERIAL_BFIN_DMA
diff --git a/drivers/tty/serial/crisv10.c b/drivers/tty/serial/crisv10.c
index 80b6b1b..35ee6a2 100644
--- a/drivers/tty/serial/crisv10.c
+++ b/drivers/tty/serial/crisv10.c
@@ -955,7 +955,7 @@
 /* Calculate the chartime depending on baudrate, numbor of bits etc. */
 static void update_char_time(struct e100_serial * info)
 {
-	tcflag_t cflags = info->port.tty->termios->c_cflag;
+	tcflag_t cflags = info->port.tty->termios.c_cflag;
 	int bits;
 
 	/* calc. number of bits / data byte */
@@ -1473,7 +1473,7 @@
 		xoff = IO_FIELD(R_SERIAL0_XOFF, xoff_char,
 				STOP_CHAR(info->port.tty));
 		xoff |= IO_STATE(R_SERIAL0_XOFF, tx_stop, stop);
-		if (tty->termios->c_iflag & IXON ) {
+		if (tty->termios.c_iflag & IXON ) {
 			xoff |= IO_STATE(R_SERIAL0_XOFF, auto_xoff, enable);
 		}
 
@@ -1496,7 +1496,7 @@
 					 info->xmit.tail,SERIAL_XMIT_SIZE)));
 		xoff = IO_FIELD(R_SERIAL0_XOFF, xoff_char, STOP_CHAR(tty));
 		xoff |= IO_STATE(R_SERIAL0_XOFF, tx_stop, enable);
-		if (tty->termios->c_iflag & IXON ) {
+		if (tty->termios.c_iflag & IXON ) {
 			xoff |= IO_STATE(R_SERIAL0_XOFF, auto_xoff, enable);
 		}
 
@@ -2929,7 +2929,7 @@
 			descr[i].buf = 0;
 		}
 
-	if (!info->port.tty || (info->port.tty->termios->c_cflag & HUPCL)) {
+	if (!info->port.tty || (info->port.tty->termios.c_cflag & HUPCL)) {
 		/* hang up DTR and RTS if HUPCL is enabled */
 		e100_dtr(info, 0);
 		e100_rts(info, 0); /* could check CRTSCTS before doing this */
@@ -2953,12 +2953,12 @@
 	unsigned long flags;
 	/* first some safety checks */
 
-	if (!info->port.tty || !info->port.tty->termios)
+	if (!info->port.tty)
 		return;
 	if (!info->ioport)
 		return;
 
-	cflag = info->port.tty->termios->c_cflag;
+	cflag = info->port.tty->termios.c_cflag;
 
 	/* possibly, the tx/rx should be disabled first to do this safely */
 
@@ -3088,7 +3088,7 @@
 	info->ioport[REG_REC_CTRL] = info->rx_ctrl;
 	xoff = IO_FIELD(R_SERIAL0_XOFF, xoff_char, STOP_CHAR(info->port.tty));
 	xoff |= IO_STATE(R_SERIAL0_XOFF, tx_stop, enable);
-	if (info->port.tty->termios->c_iflag & IXON ) {
+	if (info->port.tty->termios.c_iflag & IXON ) {
 		DFLOW(DEBUG_LOG(info->line, "FLOW XOFF enabled 0x%02X\n",
 				STOP_CHAR(info->port.tty)));
 		xoff |= IO_STATE(R_SERIAL0_XOFF, auto_xoff, enable);
@@ -3355,7 +3355,7 @@
 	DFLOW(DEBUG_LOG(info->line,"rs_throttle %lu\n", tty->ldisc.chars_in_buffer(tty)));
 
 	/* Do RTS before XOFF since XOFF might take some time */
-	if (tty->termios->c_cflag & CRTSCTS) {
+	if (tty->termios.c_cflag & CRTSCTS) {
 		/* Turn off RTS line */
 		e100_rts(info, 0);
 	}
@@ -3377,7 +3377,7 @@
 	DFLOW(DEBUG_LOG(info->line,"rs_unthrottle ldisc %d\n", tty->ldisc.chars_in_buffer(tty)));
 	DFLOW(DEBUG_LOG(info->line,"rs_unthrottle flip.count: %i\n", tty->flip.count));
 	/* Do RTS before XOFF since XOFF might take some time */
-	if (tty->termios->c_cflag & CRTSCTS) {
+	if (tty->termios.c_cflag & CRTSCTS) {
 		/* Assert RTS line  */
 		e100_rts(info, 1);
 	}
@@ -3748,7 +3748,7 @@
 
 	/* Handle turning off CRTSCTS */
 	if ((old_termios->c_cflag & CRTSCTS) &&
-	    !(tty->termios->c_cflag & CRTSCTS)) {
+	    !(tty->termios.c_cflag & CRTSCTS)) {
 		tty->hw_stopped = 0;
 		rs_start(tty);
 	}
@@ -3815,7 +3815,7 @@
 	 * separate termios for callout and dialin.
 	 */
 	if (info->flags & ASYNC_NORMAL_ACTIVE)
-		info->normal_termios = *tty->termios;
+		info->normal_termios = tty->termios;
 	/*
 	 * Now we wait for the transmit buffer to clear; and we notify
 	 * the line discipline to only process XON/XOFF characters.
@@ -3976,7 +3976,7 @@
 	 */
 	if (tty_hung_up_p(filp) ||
 	    (info->flags & ASYNC_CLOSING)) {
-		wait_event_interruptible_tty(info->close_wait,
+		wait_event_interruptible_tty(tty, info->close_wait,
 			!(info->flags & ASYNC_CLOSING));
 #ifdef SERIAL_DO_RESTART
 		if (info->flags & ASYNC_HUP_NOTIFY)
@@ -3998,7 +3998,7 @@
 		return 0;
 	}
 
-	if (tty->termios->c_cflag & CLOCAL) {
+	if (tty->termios.c_cflag & CLOCAL) {
 			do_clocal = 1;
 	}
 
@@ -4052,9 +4052,9 @@
 		printk("block_til_ready blocking: ttyS%d, count = %d\n",
 		       info->line, info->count);
 #endif
-		tty_unlock();
+		tty_unlock(tty);
 		schedule();
-		tty_lock();
+		tty_lock(tty);
 	}
 	set_current_state(TASK_RUNNING);
 	remove_wait_queue(&info->open_wait, &wait);
@@ -4115,7 +4115,7 @@
 	 */
 	if (tty_hung_up_p(filp) ||
 	    (info->flags & ASYNC_CLOSING)) {
-		wait_event_interruptible_tty(info->close_wait,
+		wait_event_interruptible_tty(tty, info->close_wait,
 			!(info->flags & ASYNC_CLOSING));
 #ifdef SERIAL_DO_RESTART
 		return ((info->flags & ASYNC_HUP_NOTIFY) ?
@@ -4219,7 +4219,7 @@
 	}
 
 	if ((info->count == 1) && (info->flags & ASYNC_SPLIT_TERMIOS)) {
-		*tty->termios = info->normal_termios;
+		tty->termios = info->normal_termios;
 		change_speed(info);
 	}
 
@@ -4443,14 +4443,12 @@
 		B115200 | CS8 | CREAD | HUPCL | CLOCAL; /* is normally B9600 default... */
 	driver->init_termios.c_ispeed = 115200;
 	driver->init_termios.c_ospeed = 115200;
-	driver->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV;
+	driver->flags = TTY_DRIVER_REAL_RAW;
 
 	tty_set_operations(driver, &rs_ops);
         serial_driver = driver;
-	if (tty_register_driver(driver))
-		panic("Couldn't register serial driver\n");
-	/* do some initializing for the separate ports */
 
+	/* do some initializing for the separate ports */
 	for (i = 0, info = rs_table; i < NR_PORTS; i++,info++) {
 		if (info->enabled) {
 			if (cris_request_io_interface(info->io_if,
@@ -4502,7 +4500,12 @@
 			printk(KERN_INFO "%s%d at %p is a builtin UART with DMA\n",
 			       serial_driver->name, info->line, info->ioport);
 		}
+		tty_port_link_device(&info->port, driver, i);
 	}
+
+	if (tty_register_driver(driver))
+		panic("Couldn't register serial driver\n");
+
 #ifdef CONFIG_ETRAX_FAST_TIMER
 #ifdef CONFIG_ETRAX_SERIAL_FAST_TIMER
 	memset(fast_timers, 0, sizeof(fast_timers));
diff --git a/drivers/tty/serial/ifx6x60.c b/drivers/tty/serial/ifx6x60.c
index 3ad079f..5b9bc19 100644
--- a/drivers/tty/serial/ifx6x60.c
+++ b/drivers/tty/serial/ifx6x60.c
@@ -800,8 +800,8 @@
 	tty_port_init(pport);
 	pport->ops = &ifx_tty_port_ops;
 	ifx_dev->minor = IFX_SPI_TTY_ID;
-	ifx_dev->tty_dev = tty_register_device(tty_drv, ifx_dev->minor,
-					       &ifx_dev->spi_dev->dev);
+	ifx_dev->tty_dev = tty_port_register_device(pport, tty_drv,
+			ifx_dev->minor, &ifx_dev->spi_dev->dev);
 	if (IS_ERR(ifx_dev->tty_dev)) {
 		dev_dbg(&ifx_dev->spi_dev->dev,
 			"%s: registering tty device failed", __func__);
diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
index d5c689d6..72ec56e 100644
--- a/drivers/tty/serial/imx.c
+++ b/drivers/tty/serial/imx.c
@@ -206,7 +206,7 @@
 	unsigned short		trcv_delay; /* transceiver delay */
 	struct clk		*clk_ipg;
 	struct clk		*clk_per;
-	struct imx_uart_data	*devdata;
+	const struct imx_uart_data *devdata;
 };
 
 struct imx_port_ucrs {
@@ -1505,18 +1505,21 @@
 	pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
 	if (IS_ERR(pinctrl)) {
 		ret = PTR_ERR(pinctrl);
+		dev_err(&pdev->dev, "failed to get default pinctrl: %d\n", ret);
 		goto unmap;
 	}
 
 	sport->clk_ipg = devm_clk_get(&pdev->dev, "ipg");
 	if (IS_ERR(sport->clk_ipg)) {
 		ret = PTR_ERR(sport->clk_ipg);
+		dev_err(&pdev->dev, "failed to get ipg clk: %d\n", ret);
 		goto unmap;
 	}
 
 	sport->clk_per = devm_clk_get(&pdev->dev, "per");
 	if (IS_ERR(sport->clk_per)) {
 		ret = PTR_ERR(sport->clk_per);
+		dev_err(&pdev->dev, "failed to get per clk: %d\n", ret);
 		goto unmap;
 	}
 
diff --git a/drivers/tty/serial/ioc3_serial.c b/drivers/tty/serial/ioc3_serial.c
index 758ff310..5ac5289 100644
--- a/drivers/tty/serial/ioc3_serial.c
+++ b/drivers/tty/serial/ioc3_serial.c
@@ -1120,13 +1120,14 @@
 	struct ioc3_port *port = get_ioc3_port(the_port);
 	struct ring *inring;
 	struct ring_entry *entry;
-	struct port_hooks *hooks = port->ip_hooks;
+	struct port_hooks *hooks;
 	int byte_num;
 	char *sc;
 	int loop_counter;
 
 	BUG_ON(!(len >= 0));
 	BUG_ON(!port);
+	hooks = port->ip_hooks;
 
 	/* There is a nasty timing issue in the IOC3. When the rx_timer
 	 * expires or the rx_high condition arises, we take an interrupt.
diff --git a/drivers/tty/serial/ioc4_serial.c b/drivers/tty/serial/ioc4_serial.c
index e16894f..3e7da10 100644
--- a/drivers/tty/serial/ioc4_serial.c
+++ b/drivers/tty/serial/ioc4_serial.c
@@ -1803,7 +1803,7 @@
 	ioc4_set_proto(port, the_port->mapbase);
 
 	/* set the speed of the serial port */
-	ioc4_change_speed(the_port, state->port.tty->termios,
+	ioc4_change_speed(the_port, &state->port.tty->termios,
 			  (struct ktermios *)0);
 
 	return 0;
@@ -2069,13 +2069,14 @@
 	struct ioc4_port *port = get_ioc4_port(the_port, 0);
 	struct ring *inring;
 	struct ring_entry *entry;
-	struct hooks *hooks = port->ip_hooks;
+	struct hooks *hooks;
 	int byte_num;
 	char *sc;
 	int loop_counter;
 
 	BUG_ON(!(len >= 0));
 	BUG_ON(!port);
+	hooks = port->ip_hooks;
 
 	/* There is a nasty timing issue in the IOC4. When the rx_timer
 	 * expires or the rx_high condition arises, we take an interrupt.
diff --git a/drivers/tty/serial/jsm/jsm_tty.c b/drivers/tty/serial/jsm/jsm_tty.c
index 434bd88..7139796 100644
--- a/drivers/tty/serial/jsm/jsm_tty.c
+++ b/drivers/tty/serial/jsm/jsm_tty.c
@@ -161,7 +161,7 @@
 	struct ktermios *termios;
 
 	spin_lock_irqsave(&port->lock, lock_flags);
-	termios = port->state->port.tty->termios;
+	termios = &port->state->port.tty->termios;
 	if (ch == termios->c_cc[VSTART])
 		channel->ch_bd->bd_ops->send_start_character(channel);
 
@@ -250,7 +250,7 @@
 	channel->ch_cached_lsr = 0;
 	channel->ch_stops_sent = 0;
 
-	termios = port->state->port.tty->termios;
+	termios = &port->state->port.tty->termios;
 	channel->ch_c_cflag	= termios->c_cflag;
 	channel->ch_c_iflag	= termios->c_iflag;
 	channel->ch_c_oflag	= termios->c_oflag;
@@ -283,7 +283,7 @@
 	jsm_printk(CLOSE, INFO, &channel->ch_bd->pci_dev, "start\n");
 
 	bd = channel->ch_bd;
-	ts = port->state->port.tty->termios;
+	ts = &port->state->port.tty->termios;
 
 	channel->ch_flags &= ~(CH_STOPI);
 
@@ -567,7 +567,7 @@
 	 *input data and return immediately.
 	 */
 	if (!tp ||
-		!(tp->termios->c_cflag & CREAD) ) {
+		!(tp->termios.c_cflag & CREAD) ) {
 
 		jsm_printk(READ, INFO, &ch->ch_bd->pci_dev,
 			"input. dropping %d bytes on port %d...\n", data_len, ch->ch_portnum);
diff --git a/drivers/tty/serial/lpc32xx_hs.c b/drivers/tty/serial/lpc32xx_hs.c
new file mode 100644
index 0000000..ba3af3b
--- /dev/null
+++ b/drivers/tty/serial/lpc32xx_hs.c
@@ -0,0 +1,823 @@
+/*
+ * High Speed Serial Ports on NXP LPC32xx SoC
+ *
+ * Authors: Kevin Wells <kevin.wells@nxp.com>
+ *          Roland Stigge <stigge@antcom.de>
+ *
+ * Copyright (C) 2010 NXP Semiconductors
+ * Copyright (C) 2012 Roland Stigge
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/module.h>
+#include <linux/ioport.h>
+#include <linux/init.h>
+#include <linux/console.h>
+#include <linux/sysrq.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/serial_core.h>
+#include <linux/serial.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/nmi.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/gpio.h>
+#include <linux/of.h>
+#include <mach/platform.h>
+#include <mach/hardware.h>
+
+/*
+ * High Speed UART register offsets
+ */
+#define LPC32XX_HSUART_FIFO(x)			((x) + 0x00)
+#define LPC32XX_HSUART_LEVEL(x)			((x) + 0x04)
+#define LPC32XX_HSUART_IIR(x)			((x) + 0x08)
+#define LPC32XX_HSUART_CTRL(x)			((x) + 0x0C)
+#define LPC32XX_HSUART_RATE(x)			((x) + 0x10)
+
+#define LPC32XX_HSU_BREAK_DATA			(1 << 10)
+#define LPC32XX_HSU_ERROR_DATA			(1 << 9)
+#define LPC32XX_HSU_RX_EMPTY			(1 << 8)
+
+#define LPC32XX_HSU_TX_LEV(n)			(((n) >> 8) & 0xFF)
+#define LPC32XX_HSU_RX_LEV(n)			((n) & 0xFF)
+
+#define LPC32XX_HSU_TX_INT_SET			(1 << 6)
+#define LPC32XX_HSU_RX_OE_INT			(1 << 5)
+#define LPC32XX_HSU_BRK_INT			(1 << 4)
+#define LPC32XX_HSU_FE_INT			(1 << 3)
+#define LPC32XX_HSU_RX_TIMEOUT_INT		(1 << 2)
+#define LPC32XX_HSU_RX_TRIG_INT			(1 << 1)
+#define LPC32XX_HSU_TX_INT			(1 << 0)
+
+#define LPC32XX_HSU_HRTS_INV			(1 << 21)
+#define LPC32XX_HSU_HRTS_TRIG_8B		(0x0 << 19)
+#define LPC32XX_HSU_HRTS_TRIG_16B		(0x1 << 19)
+#define LPC32XX_HSU_HRTS_TRIG_32B		(0x2 << 19)
+#define LPC32XX_HSU_HRTS_TRIG_48B		(0x3 << 19)
+#define LPC32XX_HSU_HRTS_EN			(1 << 18)
+#define LPC32XX_HSU_TMO_DISABLED		(0x0 << 16)
+#define LPC32XX_HSU_TMO_INACT_4B		(0x1 << 16)
+#define LPC32XX_HSU_TMO_INACT_8B		(0x2 << 16)
+#define LPC32XX_HSU_TMO_INACT_16B		(0x3 << 16)
+#define LPC32XX_HSU_HCTS_INV			(1 << 15)
+#define LPC32XX_HSU_HCTS_EN			(1 << 14)
+#define LPC32XX_HSU_OFFSET(n)			((n) << 9)
+#define LPC32XX_HSU_BREAK			(1 << 8)
+#define LPC32XX_HSU_ERR_INT_EN			(1 << 7)
+#define LPC32XX_HSU_RX_INT_EN			(1 << 6)
+#define LPC32XX_HSU_TX_INT_EN			(1 << 5)
+#define LPC32XX_HSU_RX_TL1B			(0x0 << 2)
+#define LPC32XX_HSU_RX_TL4B			(0x1 << 2)
+#define LPC32XX_HSU_RX_TL8B			(0x2 << 2)
+#define LPC32XX_HSU_RX_TL16B			(0x3 << 2)
+#define LPC32XX_HSU_RX_TL32B			(0x4 << 2)
+#define LPC32XX_HSU_RX_TL48B			(0x5 << 2)
+#define LPC32XX_HSU_TX_TLEMPTY			(0x0 << 0)
+#define LPC32XX_HSU_TX_TL0B			(0x0 << 0)
+#define LPC32XX_HSU_TX_TL4B			(0x1 << 0)
+#define LPC32XX_HSU_TX_TL8B			(0x2 << 0)
+#define LPC32XX_HSU_TX_TL16B			(0x3 << 0)
+
+#define MODNAME "lpc32xx_hsuart"
+
+struct lpc32xx_hsuart_port {
+	struct uart_port port;
+};
+
+#define FIFO_READ_LIMIT 128
+#define MAX_PORTS 3
+#define LPC32XX_TTY_NAME "ttyTX"
+static struct lpc32xx_hsuart_port lpc32xx_hs_ports[MAX_PORTS];
+
+#ifdef CONFIG_SERIAL_HS_LPC32XX_CONSOLE
+static void wait_for_xmit_empty(struct uart_port *port)
+{
+	unsigned int timeout = 10000;
+
+	do {
+		if (LPC32XX_HSU_TX_LEV(readl(LPC32XX_HSUART_LEVEL(
+							port->membase))) == 0)
+			break;
+		if (--timeout == 0)
+			break;
+		udelay(1);
+	} while (1);
+}
+
+static void wait_for_xmit_ready(struct uart_port *port)
+{
+	unsigned int timeout = 10000;
+
+	while (1) {
+		if (LPC32XX_HSU_TX_LEV(readl(LPC32XX_HSUART_LEVEL(
+							port->membase))) < 32)
+			break;
+		if (--timeout == 0)
+			break;
+		udelay(1);
+	}
+}
+
+static void lpc32xx_hsuart_console_putchar(struct uart_port *port, int ch)
+{
+	wait_for_xmit_ready(port);
+	writel((u32)ch, LPC32XX_HSUART_FIFO(port->membase));
+}
+
+static void lpc32xx_hsuart_console_write(struct console *co, const char *s,
+					 unsigned int count)
+{
+	struct lpc32xx_hsuart_port *up = &lpc32xx_hs_ports[co->index];
+	unsigned long flags;
+	int locked = 1;
+
+	touch_nmi_watchdog();
+	local_irq_save(flags);
+	if (up->port.sysrq)
+		locked = 0;
+	else if (oops_in_progress)
+		locked = spin_trylock(&up->port.lock);
+	else
+		spin_lock(&up->port.lock);
+
+	uart_console_write(&up->port, s, count, lpc32xx_hsuart_console_putchar);
+	wait_for_xmit_empty(&up->port);
+
+	if (locked)
+		spin_unlock(&up->port.lock);
+	local_irq_restore(flags);
+}
+
+static int __init lpc32xx_hsuart_console_setup(struct console *co,
+					       char *options)
+{
+	struct uart_port *port;
+	int baud = 115200;
+	int bits = 8;
+	int parity = 'n';
+	int flow = 'n';
+
+	if (co->index >= MAX_PORTS)
+		co->index = 0;
+
+	port = &lpc32xx_hs_ports[co->index].port;
+	if (!port->membase)
+		return -ENODEV;
+
+	if (options)
+		uart_parse_options(options, &baud, &parity, &bits, &flow);
+
+	return uart_set_options(port, co, baud, parity, bits, flow);
+}
+
+static struct uart_driver lpc32xx_hsuart_reg;
+static struct console lpc32xx_hsuart_console = {
+	.name		= LPC32XX_TTY_NAME,
+	.write		= lpc32xx_hsuart_console_write,
+	.device		= uart_console_device,
+	.setup		= lpc32xx_hsuart_console_setup,
+	.flags		= CON_PRINTBUFFER,
+	.index		= -1,
+	.data		= &lpc32xx_hsuart_reg,
+};
+
+static int __init lpc32xx_hsuart_console_init(void)
+{
+	register_console(&lpc32xx_hsuart_console);
+	return 0;
+}
+console_initcall(lpc32xx_hsuart_console_init);
+
+#define LPC32XX_HSUART_CONSOLE (&lpc32xx_hsuart_console)
+#else
+#define LPC32XX_HSUART_CONSOLE NULL
+#endif
+
+static struct uart_driver lpc32xx_hs_reg = {
+	.owner		= THIS_MODULE,
+	.driver_name	= MODNAME,
+	.dev_name	= LPC32XX_TTY_NAME,
+	.nr		= MAX_PORTS,
+	.cons		= LPC32XX_HSUART_CONSOLE,
+};
+static int uarts_registered;
+
+static unsigned int __serial_get_clock_div(unsigned long uartclk,
+					   unsigned long rate)
+{
+	u32 div, goodrate, hsu_rate, l_hsu_rate, comprate;
+	u32 rate_diff;
+
+	/* Find the closest divider to get the desired clock rate */
+	div = uartclk / rate;
+	goodrate = hsu_rate = (div / 14) - 1;
+	if (hsu_rate != 0)
+		hsu_rate--;
+
+	/* Tweak divider */
+	l_hsu_rate = hsu_rate + 3;
+	rate_diff = 0xFFFFFFFF;
+
+	while (hsu_rate < l_hsu_rate) {
+		comprate = uartclk / ((hsu_rate + 1) * 14);
+		if (abs(comprate - rate) < rate_diff) {
+			goodrate = hsu_rate;
+			rate_diff = abs(comprate - rate);
+		}
+
+		hsu_rate++;
+	}
+	if (hsu_rate > 0xFF)
+		hsu_rate = 0xFF;
+
+	return goodrate;
+}
+
+static void __serial_uart_flush(struct uart_port *port)
+{
+	u32 tmp;
+	int cnt = 0;
+
+	while ((readl(LPC32XX_HSUART_LEVEL(port->membase)) > 0) &&
+	       (cnt++ < FIFO_READ_LIMIT))
+		tmp = readl(LPC32XX_HSUART_FIFO(port->membase));
+}
+
+static void __serial_lpc32xx_rx(struct uart_port *port)
+{
+	unsigned int tmp, flag;
+	struct tty_struct *tty = tty_port_tty_get(&port->state->port);
+
+	if (!tty) {
+		/* Discard data: no tty available */
+		while (!(readl(LPC32XX_HSUART_FIFO(port->membase)) &
+			 LPC32XX_HSU_RX_EMPTY))
+			;
+
+		return;
+	}
+
+	/* Read data from FIFO and push into terminal */
+	tmp = readl(LPC32XX_HSUART_FIFO(port->membase));
+	while (!(tmp & LPC32XX_HSU_RX_EMPTY)) {
+		flag = TTY_NORMAL;
+		port->icount.rx++;
+
+		if (tmp & LPC32XX_HSU_ERROR_DATA) {
+			/* Framing error */
+			writel(LPC32XX_HSU_FE_INT,
+			       LPC32XX_HSUART_IIR(port->membase));
+			port->icount.frame++;
+			flag = TTY_FRAME;
+			tty_insert_flip_char(tty, 0, TTY_FRAME);
+		}
+
+		tty_insert_flip_char(tty, (tmp & 0xFF), flag);
+
+		tmp = readl(LPC32XX_HSUART_FIFO(port->membase));
+	}
+	tty_flip_buffer_push(tty);
+	tty_kref_put(tty);
+}
+
+static void __serial_lpc32xx_tx(struct uart_port *port)
+{
+	struct circ_buf *xmit = &port->state->xmit;
+	unsigned int tmp;
+
+	if (port->x_char) {
+		writel((u32)port->x_char, LPC32XX_HSUART_FIFO(port->membase));
+		port->icount.tx++;
+		port->x_char = 0;
+		return;
+	}
+
+	if (uart_circ_empty(xmit) || uart_tx_stopped(port))
+		goto exit_tx;
+
+	/* Transfer data */
+	while (LPC32XX_HSU_TX_LEV(readl(
+		LPC32XX_HSUART_LEVEL(port->membase))) < 64) {
+		writel((u32) xmit->buf[xmit->tail],
+		       LPC32XX_HSUART_FIFO(port->membase));
+		xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+		port->icount.tx++;
+		if (uart_circ_empty(xmit))
+			break;
+	}
+
+	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+		uart_write_wakeup(port);
+
+exit_tx:
+	if (uart_circ_empty(xmit)) {
+		tmp = readl(LPC32XX_HSUART_CTRL(port->membase));
+		tmp &= ~LPC32XX_HSU_TX_INT_EN;
+		writel(tmp, LPC32XX_HSUART_CTRL(port->membase));
+	}
+}
+
+static irqreturn_t serial_lpc32xx_interrupt(int irq, void *dev_id)
+{
+	struct uart_port *port = dev_id;
+	struct tty_struct *tty = tty_port_tty_get(&port->state->port);
+	u32 status;
+
+	spin_lock(&port->lock);
+
+	/* Read UART status and clear latched interrupts */
+	status = readl(LPC32XX_HSUART_IIR(port->membase));
+
+	if (status & LPC32XX_HSU_BRK_INT) {
+		/* Break received */
+		writel(LPC32XX_HSU_BRK_INT, LPC32XX_HSUART_IIR(port->membase));
+		port->icount.brk++;
+		uart_handle_break(port);
+	}
+
+	/* Framing error */
+	if (status & LPC32XX_HSU_FE_INT)
+		writel(LPC32XX_HSU_FE_INT, LPC32XX_HSUART_IIR(port->membase));
+
+	if (status & LPC32XX_HSU_RX_OE_INT) {
+		/* Receive FIFO overrun */
+		writel(LPC32XX_HSU_RX_OE_INT,
+		       LPC32XX_HSUART_IIR(port->membase));
+		port->icount.overrun++;
+		if (tty) {
+			tty_insert_flip_char(tty, 0, TTY_OVERRUN);
+			tty_schedule_flip(tty);
+		}
+	}
+
+	/* Data received? */
+	if (status & (LPC32XX_HSU_RX_TIMEOUT_INT | LPC32XX_HSU_RX_TRIG_INT)) {
+		__serial_lpc32xx_rx(port);
+		if (tty)
+			tty_flip_buffer_push(tty);
+	}
+
+	/* Transmit data request? */
+	if ((status & LPC32XX_HSU_TX_INT) && (!uart_tx_stopped(port))) {
+		writel(LPC32XX_HSU_TX_INT, LPC32XX_HSUART_IIR(port->membase));
+		__serial_lpc32xx_tx(port);
+	}
+
+	spin_unlock(&port->lock);
+	tty_kref_put(tty);
+
+	return IRQ_HANDLED;
+}
+
+/* port->lock is not held.  */
+static unsigned int serial_lpc32xx_tx_empty(struct uart_port *port)
+{
+	unsigned int ret = 0;
+
+	if (LPC32XX_HSU_TX_LEV(readl(LPC32XX_HSUART_LEVEL(port->membase))) == 0)
+		ret = TIOCSER_TEMT;
+
+	return ret;
+}
+
+/* port->lock held by caller.  */
+static void serial_lpc32xx_set_mctrl(struct uart_port *port,
+				     unsigned int mctrl)
+{
+	/* No signals are supported on HS UARTs */
+}
+
+/* port->lock is held by caller and interrupts are disabled.  */
+static unsigned int serial_lpc32xx_get_mctrl(struct uart_port *port)
+{
+	/* No signals are supported on HS UARTs */
+	return TIOCM_CAR | TIOCM_DSR | TIOCM_CTS;
+}
+
+/* port->lock held by caller.  */
+static void serial_lpc32xx_stop_tx(struct uart_port *port)
+{
+	u32 tmp;
+
+	tmp = readl(LPC32XX_HSUART_CTRL(port->membase));
+	tmp &= ~LPC32XX_HSU_TX_INT_EN;
+	writel(tmp, LPC32XX_HSUART_CTRL(port->membase));
+}
+
+/* port->lock held by caller.  */
+static void serial_lpc32xx_start_tx(struct uart_port *port)
+{
+	u32 tmp;
+
+	__serial_lpc32xx_tx(port);
+	tmp = readl(LPC32XX_HSUART_CTRL(port->membase));
+	tmp |= LPC32XX_HSU_TX_INT_EN;
+	writel(tmp, LPC32XX_HSUART_CTRL(port->membase));
+}
+
+/* port->lock held by caller.  */
+static void serial_lpc32xx_stop_rx(struct uart_port *port)
+{
+	u32 tmp;
+
+	tmp = readl(LPC32XX_HSUART_CTRL(port->membase));
+	tmp &= ~(LPC32XX_HSU_RX_INT_EN | LPC32XX_HSU_ERR_INT_EN);
+	writel(tmp, LPC32XX_HSUART_CTRL(port->membase));
+
+	writel((LPC32XX_HSU_BRK_INT | LPC32XX_HSU_RX_OE_INT |
+		LPC32XX_HSU_FE_INT), LPC32XX_HSUART_IIR(port->membase));
+}
+
+/* port->lock held by caller.  */
+static void serial_lpc32xx_enable_ms(struct uart_port *port)
+{
+	/* Modem status is not supported */
+}
+
+/* port->lock is not held.  */
+static void serial_lpc32xx_break_ctl(struct uart_port *port,
+				     int break_state)
+{
+	unsigned long flags;
+	u32 tmp;
+
+	spin_lock_irqsave(&port->lock, flags);
+	tmp = readl(LPC32XX_HSUART_CTRL(port->membase));
+	if (break_state != 0)
+		tmp |= LPC32XX_HSU_BREAK;
+	else
+		tmp &= ~LPC32XX_HSU_BREAK;
+	writel(tmp, LPC32XX_HSUART_CTRL(port->membase));
+	spin_unlock_irqrestore(&port->lock, flags);
+}
+
+/* LPC3250 Errata HSUART.1: Hang workaround via loopback mode on inactivity */
+static void lpc32xx_loopback_set(resource_size_t mapbase, int state)
+{
+	int bit;
+	u32 tmp;
+
+	switch (mapbase) {
+	case LPC32XX_HS_UART1_BASE:
+		bit = 0;
+		break;
+	case LPC32XX_HS_UART2_BASE:
+		bit = 1;
+		break;
+	case LPC32XX_HS_UART7_BASE:
+		bit = 6;
+		break;
+	default:
+		WARN(1, "lpc32xx_hs: Warning: Unknown port at %08x\n", mapbase);
+		return;
+	}
+
+	tmp = readl(LPC32XX_UARTCTL_CLOOP);
+	if (state)
+		tmp |= (1 << bit);
+	else
+		tmp &= ~(1 << bit);
+	writel(tmp, LPC32XX_UARTCTL_CLOOP);
+}
+
+/* port->lock is not held.  */
+static int serial_lpc32xx_startup(struct uart_port *port)
+{
+	int retval;
+	unsigned long flags;
+	u32 tmp;
+
+	spin_lock_irqsave(&port->lock, flags);
+
+	__serial_uart_flush(port);
+
+	writel((LPC32XX_HSU_TX_INT | LPC32XX_HSU_FE_INT |
+		LPC32XX_HSU_BRK_INT | LPC32XX_HSU_RX_OE_INT),
+	       LPC32XX_HSUART_IIR(port->membase));
+
+	writel(0xFF, LPC32XX_HSUART_RATE(port->membase));
+
+	/*
+	 * Set receiver timeout, HSU offset of 20, no break, no interrupts,
+	 * and default FIFO trigger levels
+	 */
+	tmp = LPC32XX_HSU_TX_TL8B | LPC32XX_HSU_RX_TL32B |
+		LPC32XX_HSU_OFFSET(20) | LPC32XX_HSU_TMO_INACT_4B;
+	writel(tmp, LPC32XX_HSUART_CTRL(port->membase));
+
+	lpc32xx_loopback_set(port->mapbase, 0); /* get out of loopback mode */
+
+	spin_unlock_irqrestore(&port->lock, flags);
+
+	retval = request_irq(port->irq, serial_lpc32xx_interrupt,
+			     0, MODNAME, port);
+	if (!retval)
+		writel((tmp | LPC32XX_HSU_RX_INT_EN | LPC32XX_HSU_ERR_INT_EN),
+		       LPC32XX_HSUART_CTRL(port->membase));
+
+	return retval;
+}
+
+/* port->lock is not held.  */
+static void serial_lpc32xx_shutdown(struct uart_port *port)
+{
+	u32 tmp;
+	unsigned long flags;
+
+	spin_lock_irqsave(&port->lock, flags);
+
+	tmp = LPC32XX_HSU_TX_TL8B | LPC32XX_HSU_RX_TL32B |
+		LPC32XX_HSU_OFFSET(20) | LPC32XX_HSU_TMO_INACT_4B;
+	writel(tmp, LPC32XX_HSUART_CTRL(port->membase));
+
+	lpc32xx_loopback_set(port->mapbase, 1); /* go to loopback mode */
+
+	spin_unlock_irqrestore(&port->lock, flags);
+
+	free_irq(port->irq, port);
+}
+
+/* port->lock is not held.  */
+static void serial_lpc32xx_set_termios(struct uart_port *port,
+				       struct ktermios *termios,
+				       struct ktermios *old)
+{
+	unsigned long flags;
+	unsigned int baud, quot;
+	u32 tmp;
+
+	/* Always 8-bit, no parity, 1 stop bit */
+	termios->c_cflag &= ~(CSIZE | CSTOPB | PARENB | PARODD);
+	termios->c_cflag |= CS8;
+
+	termios->c_cflag &= ~(HUPCL | CMSPAR | CLOCAL | CRTSCTS);
+
+	baud = uart_get_baud_rate(port, termios, old, 0,
+				  port->uartclk / 14);
+
+	quot = __serial_get_clock_div(port->uartclk, baud);
+
+	spin_lock_irqsave(&port->lock, flags);
+
+	/* Ignore characters? */
+	tmp = readl(LPC32XX_HSUART_CTRL(port->membase));
+	if ((termios->c_cflag & CREAD) == 0)
+		tmp &= ~(LPC32XX_HSU_RX_INT_EN | LPC32XX_HSU_ERR_INT_EN);
+	else
+		tmp |= LPC32XX_HSU_RX_INT_EN | LPC32XX_HSU_ERR_INT_EN;
+	writel(tmp, LPC32XX_HSUART_CTRL(port->membase));
+
+	writel(quot, LPC32XX_HSUART_RATE(port->membase));
+
+	uart_update_timeout(port, termios->c_cflag, baud);
+
+	spin_unlock_irqrestore(&port->lock, flags);
+
+	/* Don't rewrite B0 */
+	if (tty_termios_baud_rate(termios))
+		tty_termios_encode_baud_rate(termios, baud, baud);
+}
+
+static const char *serial_lpc32xx_type(struct uart_port *port)
+{
+	return MODNAME;
+}
+
+static void serial_lpc32xx_release_port(struct uart_port *port)
+{
+	if ((port->iotype == UPIO_MEM32) && (port->mapbase)) {
+		if (port->flags & UPF_IOREMAP) {
+			iounmap(port->membase);
+			port->membase = NULL;
+		}
+
+		release_mem_region(port->mapbase, SZ_4K);
+	}
+}
+
+static int serial_lpc32xx_request_port(struct uart_port *port)
+{
+	int ret = -ENODEV;
+
+	if ((port->iotype == UPIO_MEM32) && (port->mapbase)) {
+		ret = 0;
+
+		if (!request_mem_region(port->mapbase, SZ_4K, MODNAME))
+			ret = -EBUSY;
+		else if (port->flags & UPF_IOREMAP) {
+			port->membase = ioremap(port->mapbase, SZ_4K);
+			if (!port->membase) {
+				release_mem_region(port->mapbase, SZ_4K);
+				ret = -ENOMEM;
+			}
+		}
+	}
+
+	return ret;
+}
+
+static void serial_lpc32xx_config_port(struct uart_port *port, int uflags)
+{
+	int ret;
+
+	ret = serial_lpc32xx_request_port(port);
+	if (ret < 0)
+		return;
+	port->type = PORT_UART00;
+	port->fifosize = 64;
+
+	__serial_uart_flush(port);
+
+	writel((LPC32XX_HSU_TX_INT | LPC32XX_HSU_FE_INT |
+		LPC32XX_HSU_BRK_INT | LPC32XX_HSU_RX_OE_INT),
+	       LPC32XX_HSUART_IIR(port->membase));
+
+	writel(0xFF, LPC32XX_HSUART_RATE(port->membase));
+
+	/* Set receiver timeout, HSU offset of 20, no break, no interrupts,
+	   and default FIFO trigger levels */
+	writel(LPC32XX_HSU_TX_TL8B | LPC32XX_HSU_RX_TL32B |
+	       LPC32XX_HSU_OFFSET(20) | LPC32XX_HSU_TMO_INACT_4B,
+	       LPC32XX_HSUART_CTRL(port->membase));
+}
+
+static int serial_lpc32xx_verify_port(struct uart_port *port,
+				      struct serial_struct *ser)
+{
+	int ret = 0;
+
+	if (ser->type != PORT_UART00)
+		ret = -EINVAL;
+
+	return ret;
+}
+
+static struct uart_ops serial_lpc32xx_pops = {
+	.tx_empty	= serial_lpc32xx_tx_empty,
+	.set_mctrl	= serial_lpc32xx_set_mctrl,
+	.get_mctrl	= serial_lpc32xx_get_mctrl,
+	.stop_tx	= serial_lpc32xx_stop_tx,
+	.start_tx	= serial_lpc32xx_start_tx,
+	.stop_rx	= serial_lpc32xx_stop_rx,
+	.enable_ms	= serial_lpc32xx_enable_ms,
+	.break_ctl	= serial_lpc32xx_break_ctl,
+	.startup	= serial_lpc32xx_startup,
+	.shutdown	= serial_lpc32xx_shutdown,
+	.set_termios	= serial_lpc32xx_set_termios,
+	.type		= serial_lpc32xx_type,
+	.release_port	= serial_lpc32xx_release_port,
+	.request_port	= serial_lpc32xx_request_port,
+	.config_port	= serial_lpc32xx_config_port,
+	.verify_port	= serial_lpc32xx_verify_port,
+};
+
+/*
+ * Register a set of serial devices attached to a platform device
+ */
+static int __devinit serial_hs_lpc32xx_probe(struct platform_device *pdev)
+{
+	struct lpc32xx_hsuart_port *p = &lpc32xx_hs_ports[uarts_registered];
+	int ret = 0;
+	struct resource *res;
+
+	if (uarts_registered >= MAX_PORTS) {
+		dev_err(&pdev->dev,
+			"Error: Number of possible ports exceeded (%d)!\n",
+			uarts_registered + 1);
+		return -ENXIO;
+	}
+
+	memset(p, 0, sizeof(*p));
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(&pdev->dev,
+			"Error getting mem resource for HS UART port %d\n",
+			uarts_registered);
+		return -ENXIO;
+	}
+	p->port.mapbase = res->start;
+	p->port.membase = NULL;
+
+	p->port.irq = platform_get_irq(pdev, 0);
+	if (p->port.irq < 0) {
+		dev_err(&pdev->dev, "Error getting irq for HS UART port %d\n",
+			uarts_registered);
+		return p->port.irq;
+	}
+
+	p->port.iotype = UPIO_MEM32;
+	p->port.uartclk = LPC32XX_MAIN_OSC_FREQ;
+	p->port.regshift = 2;
+	p->port.flags = UPF_BOOT_AUTOCONF | UPF_FIXED_PORT | UPF_IOREMAP;
+	p->port.dev = &pdev->dev;
+	p->port.ops = &serial_lpc32xx_pops;
+	p->port.line = uarts_registered++;
+	spin_lock_init(&p->port.lock);
+
+	/* send port to loopback mode by default */
+	lpc32xx_loopback_set(p->port.mapbase, 1);
+
+	ret = uart_add_one_port(&lpc32xx_hs_reg, &p->port);
+
+	platform_set_drvdata(pdev, p);
+
+	return ret;
+}
+
+/*
+ * Remove serial ports registered against a platform device.
+ */
+static int __devexit serial_hs_lpc32xx_remove(struct platform_device *pdev)
+{
+	struct lpc32xx_hsuart_port *p = platform_get_drvdata(pdev);
+
+	uart_remove_one_port(&lpc32xx_hs_reg, &p->port);
+
+	return 0;
+}
+
+
+#ifdef CONFIG_PM
+static int serial_hs_lpc32xx_suspend(struct platform_device *pdev,
+				     pm_message_t state)
+{
+	struct lpc32xx_hsuart_port *p = platform_get_drvdata(pdev);
+
+	uart_suspend_port(&lpc32xx_hs_reg, &p->port);
+
+	return 0;
+}
+
+static int serial_hs_lpc32xx_resume(struct platform_device *pdev)
+{
+	struct lpc32xx_hsuart_port *p = platform_get_drvdata(pdev);
+
+	uart_resume_port(&lpc32xx_hs_reg, &p->port);
+
+	return 0;
+}
+#else
+#define serial_hs_lpc32xx_suspend	NULL
+#define serial_hs_lpc32xx_resume	NULL
+#endif
+
+static const struct of_device_id serial_hs_lpc32xx_dt_ids[] = {
+	{ .compatible = "nxp,lpc3220-hsuart" },
+	{ /* sentinel */ }
+};
+
+MODULE_DEVICE_TABLE(of, serial_hs_lpc32xx_dt_ids);
+
+static struct platform_driver serial_hs_lpc32xx_driver = {
+	.probe		= serial_hs_lpc32xx_probe,
+	.remove		= __devexit_p(serial_hs_lpc32xx_remove),
+	.suspend	= serial_hs_lpc32xx_suspend,
+	.resume		= serial_hs_lpc32xx_resume,
+	.driver		= {
+		.name	= MODNAME,
+		.owner	= THIS_MODULE,
+		.of_match_table	= serial_hs_lpc32xx_dt_ids,
+	},
+};
+
+static int __init lpc32xx_hsuart_init(void)
+{
+	int ret;
+
+	ret = uart_register_driver(&lpc32xx_hs_reg);
+	if (ret)
+		return ret;
+
+	ret = platform_driver_register(&serial_hs_lpc32xx_driver);
+	if (ret)
+		uart_unregister_driver(&lpc32xx_hs_reg);
+
+	return ret;
+}
+
+static void __exit lpc32xx_hsuart_exit(void)
+{
+	platform_driver_unregister(&serial_hs_lpc32xx_driver);
+	uart_unregister_driver(&lpc32xx_hs_reg);
+}
+
+module_init(lpc32xx_hsuart_init);
+module_exit(lpc32xx_hsuart_exit);
+
+MODULE_AUTHOR("Kevin Wells <kevin.wells@nxp.com>");
+MODULE_AUTHOR("Roland Stigge <stigge@antcom.de>");
+MODULE_DESCRIPTION("NXP LPC32XX High Speed UART driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/tty/serial/m32r_sio.c b/drivers/tty/serial/m32r_sio.c
index a070362..b13949a 100644
--- a/drivers/tty/serial/m32r_sio.c
+++ b/drivers/tty/serial/m32r_sio.c
@@ -44,8 +44,6 @@
 #include <asm/io.h>
 #include <asm/irq.h>
 
-#define PORT_M32R_BASE	PORT_M32R_SIO
-#define PORT_INDEX(x)	(x - PORT_M32R_BASE + 1)
 #define BAUD_RATE	115200
 
 #include <linux/serial_core.h>
@@ -132,22 +130,6 @@
 
 static struct irq_info irq_lists[NR_IRQS];
 
-/*
- * Here we define the default xmit fifo size used for each type of UART.
- */
-static const struct serial_uart_config uart_config[] = {
-	[PORT_UNKNOWN] = {
-		.name			= "unknown",
-		.dfl_xmit_fifo_size	= 1,
-		.flags			= 0,
-	},
-	[PORT_INDEX(PORT_M32R_SIO)] = {
-		.name			= "M32RSIO",
-		.dfl_xmit_fifo_size	= 1,
-		.flags			= 0,
-	},
-};
-
 #ifdef CONFIG_SERIAL_M32R_PLDSIO
 
 #define __sio_in(x) inw((unsigned long)(x))
@@ -907,8 +889,7 @@
 
 	spin_lock_irqsave(&up->port.lock, flags);
 
-	up->port.type = (PORT_M32R_SIO - PORT_M32R_BASE + 1);
-	up->port.fifosize = uart_config[up->port.type].dfl_xmit_fifo_size;
+	up->port.fifosize = 1;
 
 	spin_unlock_irqrestore(&up->port.lock, flags);
 }
@@ -916,23 +897,11 @@
 static int
 m32r_sio_verify_port(struct uart_port *port, struct serial_struct *ser)
 {
-	if (ser->irq >= nr_irqs || ser->irq < 0 ||
-	    ser->baud_base < 9600 || ser->type < PORT_UNKNOWN ||
-	    ser->type >= ARRAY_SIZE(uart_config))
+	if (ser->irq >= nr_irqs || ser->irq < 0 || ser->baud_base < 9600)
 		return -EINVAL;
 	return 0;
 }
 
-static const char *
-m32r_sio_type(struct uart_port *port)
-{
-	int type = port->type;
-
-	if (type >= ARRAY_SIZE(uart_config))
-		type = 0;
-	return uart_config[type].name;
-}
-
 static struct uart_ops m32r_sio_pops = {
 	.tx_empty	= m32r_sio_tx_empty,
 	.set_mctrl	= m32r_sio_set_mctrl,
@@ -946,7 +915,6 @@
 	.shutdown	= m32r_sio_shutdown,
 	.set_termios	= m32r_sio_set_termios,
 	.pm		= m32r_sio_pm,
-	.type		= m32r_sio_type,
 	.release_port	= m32r_sio_release_port,
 	.request_port	= m32r_sio_request_port,
 	.config_port	= m32r_sio_config_port,
diff --git a/drivers/tty/serial/max3100.c b/drivers/tty/serial/max3100.c
index b4902b9..46043c2 100644
--- a/drivers/tty/serial/max3100.c
+++ b/drivers/tty/serial/max3100.c
@@ -910,17 +910,7 @@
 	.resume		= max3100_resume,
 };
 
-static int __init max3100_init(void)
-{
-	return spi_register_driver(&max3100_driver);
-}
-module_init(max3100_init);
-
-static void __exit max3100_exit(void)
-{
-	spi_unregister_driver(&max3100_driver);
-}
-module_exit(max3100_exit);
+module_spi_driver(max3100_driver);
 
 MODULE_DESCRIPTION("MAX3100 driver");
 MODULE_AUTHOR("Christian Pellegrin <chripell@evolware.org>");
diff --git a/drivers/tty/serial/max3107.c b/drivers/tty/serial/max3107.c
deleted file mode 100644
index 17c7ba8..0000000
--- a/drivers/tty/serial/max3107.c
+++ /dev/null
@@ -1,1215 +0,0 @@
-/*
- *  max3107.c - spi uart protocol driver for Maxim 3107
- *  Based on max3100.c
- *	by Christian Pellegrin <chripell@evolware.org>
- *  and	max3110.c
- *	by Feng Tang <feng.tang@intel.com>
- *
- *  Copyright (C) Aavamobile 2009
- *
- * ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
- *
- *  This program is free software; you can redistribute it and/or modify
- *  it under the terms of the GNU General Public License as published by
- *  the Free Software Foundation; either version 2 of the License, or
- *  (at your option) any later version.
- *
- *  This program is distributed in the hope that it will be useful,
- *  but WITHOUT ANY WARRANTY; without even the implied warranty of
- *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *  GNU General Public License for more details.
- *
- *  You should have received a copy of the GNU General Public License
- *  along with this program; if not, write to the Free Software
- *  Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- *
- * ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
- *
- */
-
-#include <linux/delay.h>
-#include <linux/device.h>
-#include <linux/serial_core.h>
-#include <linux/serial.h>
-#include <linux/tty.h>
-#include <linux/tty_flip.h>
-#include <linux/gpio.h>
-#include <linux/spi/spi.h>
-#include <linux/freezer.h>
-#include <linux/module.h>
-#include "max3107.h"
-
-static const struct baud_table brg26_ext[] = {
-	{ 300,    MAX3107_BRG26_B300 },
-	{ 600,    MAX3107_BRG26_B600 },
-	{ 1200,   MAX3107_BRG26_B1200 },
-	{ 2400,   MAX3107_BRG26_B2400 },
-	{ 4800,   MAX3107_BRG26_B4800 },
-	{ 9600,   MAX3107_BRG26_B9600 },
-	{ 19200,  MAX3107_BRG26_B19200 },
-	{ 57600,  MAX3107_BRG26_B57600 },
-	{ 115200, MAX3107_BRG26_B115200 },
-	{ 230400, MAX3107_BRG26_B230400 },
-	{ 460800, MAX3107_BRG26_B460800 },
-	{ 921600, MAX3107_BRG26_B921600 },
-	{ 0, 0 }
-};
-
-static const struct baud_table brg13_int[] = {
-	{ 300,    MAX3107_BRG13_IB300 },
-	{ 600,    MAX3107_BRG13_IB600 },
-	{ 1200,   MAX3107_BRG13_IB1200 },
-	{ 2400,   MAX3107_BRG13_IB2400 },
-	{ 4800,   MAX3107_BRG13_IB4800 },
-	{ 9600,   MAX3107_BRG13_IB9600 },
-	{ 19200,  MAX3107_BRG13_IB19200 },
-	{ 57600,  MAX3107_BRG13_IB57600 },
-	{ 115200, MAX3107_BRG13_IB115200 },
-	{ 230400, MAX3107_BRG13_IB230400 },
-	{ 460800, MAX3107_BRG13_IB460800 },
-	{ 921600, MAX3107_BRG13_IB921600 },
-	{ 0, 0 }
-};
-
-static u32 get_new_brg(int baud, struct max3107_port *s)
-{
-	int i;
-	const struct baud_table *baud_tbl = s->baud_tbl;
-
-	for (i = 0; i < 13; i++) {
-		if (baud == baud_tbl[i].baud)
-			return baud_tbl[i].new_brg;
-	}
-
-	return 0;
-}
-
-/* Perform SPI transfer for write/read of device register(s) */
-int max3107_rw(struct max3107_port *s, u8 *tx, u8 *rx, int len)
-{
-	struct spi_message spi_msg;
-	struct spi_transfer spi_xfer;
-
-	/* Initialize SPI ,message */
-	spi_message_init(&spi_msg);
-
-	/* Initialize SPI transfer */
-	memset(&spi_xfer, 0, sizeof spi_xfer);
-	spi_xfer.len = len;
-	spi_xfer.tx_buf = tx;
-	spi_xfer.rx_buf = rx;
-	spi_xfer.speed_hz = MAX3107_SPI_SPEED;
-
-	/* Add SPI transfer to SPI message */
-	spi_message_add_tail(&spi_xfer, &spi_msg);
-
-#ifdef DBG_TRACE_SPI_DATA
-	{
-		int i;
-		pr_info("tx len %d:\n", spi_xfer.len);
-		for (i = 0 ; i < spi_xfer.len && i < 32 ; i++)
-			pr_info(" %x", ((u8 *)spi_xfer.tx_buf)[i]);
-		pr_info("\n");
-	}
-#endif
-
-	/* Perform synchronous SPI transfer */
-	if (spi_sync(s->spi, &spi_msg)) {
-		dev_err(&s->spi->dev, "spi_sync failure\n");
-		return -EIO;
-	}
-
-#ifdef DBG_TRACE_SPI_DATA
-	if (spi_xfer.rx_buf) {
-		int i;
-		pr_info("rx len %d:\n", spi_xfer.len);
-		for (i = 0 ; i < spi_xfer.len && i < 32 ; i++)
-			pr_info(" %x", ((u8 *)spi_xfer.rx_buf)[i]);
-		pr_info("\n");
-	}
-#endif
-	return 0;
-}
-EXPORT_SYMBOL_GPL(max3107_rw);
-
-/* Puts received data to circular buffer */
-static void put_data_to_circ_buf(struct max3107_port *s, unsigned char *data,
-					int len)
-{
-	struct uart_port *port = &s->port;
-	struct tty_struct *tty;
-
-	if (!port->state)
-		return;
-
-	tty = port->state->port.tty;
-	if (!tty)
-		return;
-
-	/* Insert received data */
-	tty_insert_flip_string(tty, data, len);
-	/* Update RX counter */
-	port->icount.rx += len;
-}
-
-/* Handle data receiving */
-static void max3107_handlerx(struct max3107_port *s, u16 rxlvl)
-{
-	int i;
-	int j;
-	int len;				/* SPI transfer buffer length */
-	u16 *buf;
-	u8 *valid_str;
-
-	if (!s->rx_enabled)
-		/* RX is disabled */
-		return;
-
-	if (rxlvl == 0) {
-		/* RX fifo is empty */
-		return;
-	} else if (rxlvl >= MAX3107_RX_FIFO_SIZE) {
-		dev_warn(&s->spi->dev, "Possible RX FIFO overrun %d\n", rxlvl);
-		/* Ensure sanity of RX level */
-		rxlvl = MAX3107_RX_FIFO_SIZE;
-	}
-	if ((s->rxbuf == 0) || (s->rxstr == 0)) {
-		dev_warn(&s->spi->dev, "Rx buffer/str isn't ready\n");
-		return;
-	}
-	buf = s->rxbuf;
-	valid_str = s->rxstr;
-	while (rxlvl) {
-		pr_debug("rxlvl %d\n", rxlvl);
-		/* Clear buffer */
-		memset(buf, 0, sizeof(u16) * (MAX3107_RX_FIFO_SIZE + 2));
-		len = 0;
-		if (s->irqen_reg & MAX3107_IRQ_RXFIFO_BIT) {
-			/* First disable RX FIFO interrupt */
-			pr_debug("Disabling RX INT\n");
-			buf[0] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG);
-			s->irqen_reg &= ~MAX3107_IRQ_RXFIFO_BIT;
-			buf[0] |= s->irqen_reg;
-			len++;
-		}
-		/* Just increase the length by amount of words in FIFO since
-		 * buffer was zeroed and SPI transfer of 0x0000 means reading
-		 * from RX FIFO
-		 */
-		len += rxlvl;
-		/* Append RX level query */
-		buf[len] = MAX3107_RXFIFOLVL_REG;
-		len++;
-
-		/* Perform the SPI transfer */
-		if (max3107_rw(s, (u8 *)buf, (u8 *)buf, len * 2)) {
-			dev_err(&s->spi->dev, "SPI transfer for RX h failed\n");
-			return;
-		}
-
-		/* Skip RX FIFO interrupt disabling word if it was added */
-		j = ((len - 1) - rxlvl);
-		/* Read received words */
-		for (i = 0; i < rxlvl; i++, j++)
-			valid_str[i] = (u8)buf[j];
-		put_data_to_circ_buf(s, valid_str, rxlvl);
-		/* Get new RX level */
-		rxlvl = (buf[len - 1] & MAX3107_SPI_RX_DATA_MASK);
-	}
-
-	if (s->rx_enabled) {
-		/* RX still enabled, re-enable RX FIFO interrupt */
-		pr_debug("Enabling RX INT\n");
-		buf[0] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG);
-		s->irqen_reg |= MAX3107_IRQ_RXFIFO_BIT;
-		buf[0] |= s->irqen_reg;
-		if (max3107_rw(s, (u8 *)buf, NULL, 2))
-			dev_err(&s->spi->dev, "RX FIFO INT enabling failed\n");
-	}
-
-	/* Push the received data to receivers */
-	if (s->port.state->port.tty)
-		tty_flip_buffer_push(s->port.state->port.tty);
-}
-
-
-/* Handle data sending */
-static void max3107_handletx(struct max3107_port *s)
-{
-	struct circ_buf *xmit = &s->port.state->xmit;
-	int i;
-	unsigned long flags;
-	int len;				/* SPI transfer buffer length */
-	u16 *buf;
-
-	if (!s->tx_fifo_empty)
-		/* Don't send more data before previous data is sent */
-		return;
-
-	if (uart_circ_empty(xmit) || uart_tx_stopped(&s->port))
-		/* No data to send or TX is stopped */
-		return;
-
-	if (!s->txbuf) {
-		dev_warn(&s->spi->dev, "Txbuf isn't ready\n");
-		return;
-	}
-	buf = s->txbuf;
-	/* Get length of data pending in circular buffer */
-	len = uart_circ_chars_pending(xmit);
-	if (len) {
-		/* Limit to size of TX FIFO */
-		if (len > MAX3107_TX_FIFO_SIZE)
-			len = MAX3107_TX_FIFO_SIZE;
-
-		pr_debug("txlen %d\n", len);
-
-		/* Update TX counter */
-		s->port.icount.tx += len;
-
-		/* TX FIFO will no longer be empty */
-		s->tx_fifo_empty = 0;
-
-		i = 0;
-		if (s->irqen_reg & MAX3107_IRQ_TXEMPTY_BIT) {
-			/* First disable TX empty interrupt */
-			pr_debug("Disabling TE INT\n");
-			buf[i] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG);
-			s->irqen_reg &= ~MAX3107_IRQ_TXEMPTY_BIT;
-			buf[i] |= s->irqen_reg;
-			i++;
-			len++;
-		}
-		/* Add data to send */
-		spin_lock_irqsave(&s->port.lock, flags);
-		for ( ; i < len ; i++) {
-			buf[i] = (MAX3107_WRITE_BIT | MAX3107_THR_REG);
-			buf[i] |= ((u16)xmit->buf[xmit->tail] &
-						MAX3107_SPI_TX_DATA_MASK);
-			xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
-		}
-		spin_unlock_irqrestore(&s->port.lock, flags);
-		if (!(s->irqen_reg & MAX3107_IRQ_TXEMPTY_BIT)) {
-			/* Enable TX empty interrupt */
-			pr_debug("Enabling TE INT\n");
-			buf[i] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG);
-			s->irqen_reg |= MAX3107_IRQ_TXEMPTY_BIT;
-			buf[i] |= s->irqen_reg;
-			i++;
-			len++;
-		}
-		if (!s->tx_enabled) {
-			/* Enable TX */
-			pr_debug("Enable TX\n");
-			buf[i] = (MAX3107_WRITE_BIT | MAX3107_MODE1_REG);
-			spin_lock_irqsave(&s->data_lock, flags);
-			s->mode1_reg &= ~MAX3107_MODE1_TXDIS_BIT;
-			buf[i] |= s->mode1_reg;
-			spin_unlock_irqrestore(&s->data_lock, flags);
-			s->tx_enabled = 1;
-			i++;
-			len++;
-		}
-
-		/* Perform the SPI transfer */
-		if (max3107_rw(s, (u8 *)buf, NULL, len*2)) {
-			dev_err(&s->spi->dev,
-				"SPI transfer TX handling failed\n");
-			return;
-		}
-	}
-
-	/* Indicate wake up if circular buffer is getting low on data */
-	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
-		uart_write_wakeup(&s->port);
-
-}
-
-/* Handle interrupts
- * Also reads and returns current RX FIFO level
- */
-static u16 handle_interrupt(struct max3107_port *s)
-{
-	u16 buf[4];	/* Buffer for SPI transfers */
-	u8 irq_status;
-	u16 rx_level;
-	unsigned long flags;
-
-	/* Read IRQ status register */
-	buf[0] = MAX3107_IRQSTS_REG;
-	/* Read status IRQ status register */
-	buf[1] = MAX3107_STS_IRQSTS_REG;
-	/* Read LSR IRQ status register */
-	buf[2] = MAX3107_LSR_IRQSTS_REG;
-	/* Query RX level */
-	buf[3] = MAX3107_RXFIFOLVL_REG;
-
-	if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 8)) {
-		dev_err(&s->spi->dev,
-			"SPI transfer for INTR handling failed\n");
-		return 0;
-	}
-
-	irq_status = (u8)buf[0];
-	pr_debug("IRQSTS %x\n", irq_status);
-	rx_level = (buf[3] & MAX3107_SPI_RX_DATA_MASK);
-
-	if (irq_status & MAX3107_IRQ_LSR_BIT) {
-		/* LSR interrupt */
-		if (buf[2] & MAX3107_LSR_RXTO_BIT)
-			/* RX timeout interrupt,
-			 * handled by normal RX handling
-			 */
-			pr_debug("RX TO INT\n");
-	}
-
-	if (irq_status & MAX3107_IRQ_TXEMPTY_BIT) {
-		/* Tx empty interrupt,
-		 * disable TX and set tx_fifo_empty flag
-		 */
-		pr_debug("TE INT, disabling TX\n");
-		buf[0] = (MAX3107_WRITE_BIT | MAX3107_MODE1_REG);
-		spin_lock_irqsave(&s->data_lock, flags);
-		s->mode1_reg |= MAX3107_MODE1_TXDIS_BIT;
-		buf[0] |= s->mode1_reg;
-		spin_unlock_irqrestore(&s->data_lock, flags);
-		if (max3107_rw(s, (u8 *)buf, NULL, 2))
-			dev_err(&s->spi->dev, "SPI transfer TX dis failed\n");
-		s->tx_enabled = 0;
-		s->tx_fifo_empty = 1;
-	}
-
-	if (irq_status & MAX3107_IRQ_RXFIFO_BIT)
-		/* RX FIFO interrupt,
-		 * handled by normal RX handling
-		 */
-		pr_debug("RFIFO INT\n");
-
-	/* Return RX level */
-	return rx_level;
-}
-
-/* Trigger work thread*/
-static void max3107_dowork(struct max3107_port *s)
-{
-	if (!work_pending(&s->work) && !freezing(current) && !s->suspended)
-		queue_work(s->workqueue, &s->work);
-	else
-		dev_warn(&s->spi->dev, "interrup isn't serviced normally!\n");
-}
-
-/* Work thread */
-static void max3107_work(struct work_struct *w)
-{
-	struct max3107_port *s = container_of(w, struct max3107_port, work);
-	u16 rxlvl = 0;
-	int len;	/* SPI transfer buffer length */
-	u16 buf[5];	/* Buffer for SPI transfers */
-	unsigned long flags;
-
-	/* Start by reading current RX FIFO level */
-	buf[0] = MAX3107_RXFIFOLVL_REG;
-	if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 2)) {
-		dev_err(&s->spi->dev, "SPI transfer RX lev failed\n");
-		rxlvl = 0;
-	} else {
-		rxlvl = (buf[0] & MAX3107_SPI_RX_DATA_MASK);
-	}
-
-	do {
-		pr_debug("rxlvl %d\n", rxlvl);
-
-		/* Handle RX */
-		max3107_handlerx(s, rxlvl);
-		rxlvl = 0;
-
-		if (s->handle_irq) {
-			/* Handle pending interrupts
-			 * We also get new RX FIFO level since new data may
-			 * have been received while pushing received data to
-			 * receivers
-			 */
-			s->handle_irq = 0;
-			rxlvl = handle_interrupt(s);
-		}
-
-		/* Handle TX */
-		max3107_handletx(s);
-
-		/* Handle configuration changes */
-		len = 0;
-		spin_lock_irqsave(&s->data_lock, flags);
-		if (s->mode1_commit) {
-			pr_debug("mode1_commit\n");
-			buf[len] = (MAX3107_WRITE_BIT | MAX3107_MODE1_REG);
-			buf[len++] |= s->mode1_reg;
-			s->mode1_commit = 0;
-		}
-		if (s->lcr_commit) {
-			pr_debug("lcr_commit\n");
-			buf[len] = (MAX3107_WRITE_BIT | MAX3107_LCR_REG);
-			buf[len++] |= s->lcr_reg;
-			s->lcr_commit = 0;
-		}
-		if (s->brg_commit) {
-			pr_debug("brg_commit\n");
-			buf[len] = (MAX3107_WRITE_BIT | MAX3107_BRGDIVMSB_REG);
-			buf[len++] |= ((s->brg_cfg >> 16) &
-						MAX3107_SPI_TX_DATA_MASK);
-			buf[len] = (MAX3107_WRITE_BIT | MAX3107_BRGDIVLSB_REG);
-			buf[len++] |= ((s->brg_cfg >> 8) &
-						MAX3107_SPI_TX_DATA_MASK);
-			buf[len] = (MAX3107_WRITE_BIT | MAX3107_BRGCFG_REG);
-			buf[len++] |= ((s->brg_cfg) & 0xff);
-			s->brg_commit = 0;
-		}
-		spin_unlock_irqrestore(&s->data_lock, flags);
-
-		if (len > 0) {
-			if (max3107_rw(s, (u8 *)buf, NULL, len * 2))
-				dev_err(&s->spi->dev,
-					"SPI transfer config failed\n");
-		}
-
-		/* Reloop if interrupt handling indicated data in RX FIFO */
-	} while (rxlvl);
-
-}
-
-/* Set sleep mode */
-static void max3107_set_sleep(struct max3107_port *s, int mode)
-{
-	u16 buf[1];	/* Buffer for SPI transfer */
-	unsigned long flags;
-	pr_debug("enter, mode %d\n", mode);
-
-	buf[0] = (MAX3107_WRITE_BIT | MAX3107_MODE1_REG);
-	spin_lock_irqsave(&s->data_lock, flags);
-	switch (mode) {
-	case MAX3107_DISABLE_FORCED_SLEEP:
-			s->mode1_reg &= ~MAX3107_MODE1_FORCESLEEP_BIT;
-			break;
-	case MAX3107_ENABLE_FORCED_SLEEP:
-			s->mode1_reg |= MAX3107_MODE1_FORCESLEEP_BIT;
-			break;
-	case MAX3107_DISABLE_AUTOSLEEP:
-			s->mode1_reg &= ~MAX3107_MODE1_AUTOSLEEP_BIT;
-			break;
-	case MAX3107_ENABLE_AUTOSLEEP:
-			s->mode1_reg |= MAX3107_MODE1_AUTOSLEEP_BIT;
-			break;
-	default:
-		spin_unlock_irqrestore(&s->data_lock, flags);
-		dev_warn(&s->spi->dev, "invalid sleep mode\n");
-		return;
-	}
-	buf[0] |= s->mode1_reg;
-	spin_unlock_irqrestore(&s->data_lock, flags);
-
-	if (max3107_rw(s, (u8 *)buf, NULL, 2))
-		dev_err(&s->spi->dev, "SPI transfer sleep mode failed\n");
-
-	if (mode == MAX3107_DISABLE_AUTOSLEEP ||
-			mode == MAX3107_DISABLE_FORCED_SLEEP)
-		msleep(MAX3107_WAKEUP_DELAY);
-}
-
-/* Perform full register initialization */
-static void max3107_register_init(struct max3107_port *s)
-{
-	u16 buf[11];	/* Buffer for SPI transfers */
-
-	/* 1. Configure baud rate, 9600 as default */
-	s->baud = 9600;
-	/* the below is default*/
-	if (s->ext_clk) {
-		s->brg_cfg = MAX3107_BRG26_B9600;
-		s->baud_tbl = (struct baud_table *)brg26_ext;
-	} else {
-		s->brg_cfg = MAX3107_BRG13_IB9600;
-		s->baud_tbl = (struct baud_table *)brg13_int;
-	}
-
-	if (s->pdata->init)
-		s->pdata->init(s);
-
-	buf[0] = (MAX3107_WRITE_BIT | MAX3107_BRGDIVMSB_REG)
-		| ((s->brg_cfg >> 16) & MAX3107_SPI_TX_DATA_MASK);
-	buf[1] = (MAX3107_WRITE_BIT | MAX3107_BRGDIVLSB_REG)
-		| ((s->brg_cfg >> 8) & MAX3107_SPI_TX_DATA_MASK);
-	buf[2] = (MAX3107_WRITE_BIT | MAX3107_BRGCFG_REG)
-		| ((s->brg_cfg) & 0xff);
-
-	/* 2. Configure LCR register, 8N1 mode by default */
-	s->lcr_reg = MAX3107_LCR_WORD_LEN_8;
-	buf[3] = (MAX3107_WRITE_BIT | MAX3107_LCR_REG)
-		| s->lcr_reg;
-
-	/* 3. Configure MODE 1 register */
-	s->mode1_reg = 0;
-	/* Enable IRQ pin */
-	s->mode1_reg |= MAX3107_MODE1_IRQSEL_BIT;
-	/* Disable TX */
-	s->mode1_reg |= MAX3107_MODE1_TXDIS_BIT;
-	s->tx_enabled = 0;
-	/* RX is enabled */
-	s->rx_enabled = 1;
-	buf[4] = (MAX3107_WRITE_BIT | MAX3107_MODE1_REG)
-		| s->mode1_reg;
-
-	/* 4. Configure MODE 2 register */
-	buf[5] = (MAX3107_WRITE_BIT | MAX3107_MODE2_REG);
-	if (s->loopback) {
-		/* Enable loopback */
-		buf[5] |= MAX3107_MODE2_LOOPBACK_BIT;
-	}
-	/* Reset FIFOs */
-	buf[5] |= MAX3107_MODE2_FIFORST_BIT;
-	s->tx_fifo_empty = 1;
-
-	/* 5. Configure FIFO trigger level register */
-	buf[6] = (MAX3107_WRITE_BIT | MAX3107_FIFOTRIGLVL_REG);
-	/* RX FIFO trigger for 16 words, TX FIFO trigger not used */
-	buf[6] |= (MAX3107_FIFOTRIGLVL_RX(16) | MAX3107_FIFOTRIGLVL_TX(0));
-
-	/* 6. Configure flow control levels */
-	buf[7] = (MAX3107_WRITE_BIT | MAX3107_FLOWLVL_REG);
-	/* Flow control halt level 96, resume level 48 */
-	buf[7] |= (MAX3107_FLOWLVL_RES(48) | MAX3107_FLOWLVL_HALT(96));
-
-	/* 7. Configure flow control */
-	buf[8] = (MAX3107_WRITE_BIT | MAX3107_FLOWCTRL_REG);
-	/* Enable auto CTS and auto RTS flow control */
-	buf[8] |= (MAX3107_FLOWCTRL_AUTOCTS_BIT | MAX3107_FLOWCTRL_AUTORTS_BIT);
-
-	/* 8. Configure RX timeout register */
-	buf[9] = (MAX3107_WRITE_BIT | MAX3107_RXTO_REG);
-	/* Timeout after 48 character intervals */
-	buf[9] |= 0x0030;
-
-	/* 9. Configure LSR interrupt enable register */
-	buf[10] = (MAX3107_WRITE_BIT | MAX3107_LSR_IRQEN_REG);
-	/* Enable RX timeout interrupt */
-	buf[10] |= MAX3107_LSR_RXTO_BIT;
-
-	/* Perform SPI transfer */
-	if (max3107_rw(s, (u8 *)buf, NULL, 22))
-		dev_err(&s->spi->dev, "SPI transfer for init failed\n");
-
-	/* 10. Clear IRQ status register by reading it */
-	buf[0] = MAX3107_IRQSTS_REG;
-
-	/* 11. Configure interrupt enable register */
-	/* Enable LSR interrupt */
-	s->irqen_reg = MAX3107_IRQ_LSR_BIT;
-	/* Enable RX FIFO interrupt */
-	s->irqen_reg |= MAX3107_IRQ_RXFIFO_BIT;
-	buf[1] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG)
-		| s->irqen_reg;
-
-	/* 12. Clear FIFO reset that was set in step 6 */
-	buf[2] = (MAX3107_WRITE_BIT | MAX3107_MODE2_REG);
-	if (s->loopback) {
-		/* Keep loopback enabled */
-		buf[2] |= MAX3107_MODE2_LOOPBACK_BIT;
-	}
-
-	/* Perform SPI transfer */
-	if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 6))
-		dev_err(&s->spi->dev, "SPI transfer for init failed\n");
-
-}
-
-/* IRQ handler */
-static irqreturn_t max3107_irq(int irqno, void *dev_id)
-{
-	struct max3107_port *s = dev_id;
-
-	if (irqno != s->spi->irq) {
-		/* Unexpected IRQ */
-		return IRQ_NONE;
-	}
-
-	/* Indicate irq */
-	s->handle_irq = 1;
-
-	/* Trigger work thread */
-	max3107_dowork(s);
-
-	return IRQ_HANDLED;
-}
-
-/* HW suspension function
- *
- * Currently autosleep is used to decrease current consumption, alternative
- * approach would be to set the chip to reset mode if UART is not being
- * used but that would mess the GPIOs
- *
- */
-void max3107_hw_susp(struct max3107_port *s, int suspend)
-{
-	pr_debug("enter, suspend %d\n", suspend);
-
-	if (suspend) {
-		/* Suspend requested,
-		 * enable autosleep to decrease current consumption
-		 */
-		s->suspended = 1;
-		max3107_set_sleep(s, MAX3107_ENABLE_AUTOSLEEP);
-	} else {
-		/* Resume requested,
-		 * disable autosleep
-		 */
-		s->suspended = 0;
-		max3107_set_sleep(s, MAX3107_DISABLE_AUTOSLEEP);
-	}
-}
-EXPORT_SYMBOL_GPL(max3107_hw_susp);
-
-/* Modem status IRQ enabling */
-static void max3107_enable_ms(struct uart_port *port)
-{
-	/* Modem status not supported */
-}
-
-/* Data send function */
-static void max3107_start_tx(struct uart_port *port)
-{
-	struct max3107_port *s = container_of(port, struct max3107_port, port);
-
-	/* Trigger work thread for sending data */
-	max3107_dowork(s);
-}
-
-/* Function for checking that there is no pending transfers */
-static unsigned int max3107_tx_empty(struct uart_port *port)
-{
-	struct max3107_port *s = container_of(port, struct max3107_port, port);
-
-	pr_debug("returning %d\n",
-		  (s->tx_fifo_empty && uart_circ_empty(&s->port.state->xmit)));
-	return s->tx_fifo_empty && uart_circ_empty(&s->port.state->xmit);
-}
-
-/* Function for stopping RX */
-static void max3107_stop_rx(struct uart_port *port)
-{
-	struct max3107_port *s = container_of(port, struct max3107_port, port);
-	unsigned long flags;
-
-	/* Set RX disabled in MODE 1 register */
-	spin_lock_irqsave(&s->data_lock, flags);
-	s->mode1_reg |= MAX3107_MODE1_RXDIS_BIT;
-	s->mode1_commit = 1;
-	spin_unlock_irqrestore(&s->data_lock, flags);
-	/* Set RX disabled */
-	s->rx_enabled = 0;
-	/* Trigger work thread for doing the actual configuration change */
-	max3107_dowork(s);
-}
-
-/* Function for returning control pin states */
-static unsigned int max3107_get_mctrl(struct uart_port *port)
-{
-	/* DCD and DSR are not wired and CTS/RTS is handled automatically
-	 * so just indicate DSR and CAR asserted
-	 */
-	return TIOCM_DSR | TIOCM_CAR;
-}
-
-/* Function for setting control pin states */
-static void max3107_set_mctrl(struct uart_port *port, unsigned int mctrl)
-{
-	/* DCD and DSR are not wired and CTS/RTS is hadnled automatically
-	 * so do nothing
-	 */
-}
-
-/* Function for configuring UART parameters */
-static void max3107_set_termios(struct uart_port *port,
-				struct ktermios *termios,
-				struct ktermios *old)
-{
-	struct max3107_port *s = container_of(port, struct max3107_port, port);
-	struct tty_struct *tty;
-	int baud;
-	u16 new_lcr = 0;
-	u32 new_brg = 0;
-	unsigned long flags;
-
-	if (!port->state)
-		return;
-
-	tty = port->state->port.tty;
-	if (!tty)
-		return;
-
-	/* Get new LCR register values */
-	/* Word size */
-	if ((termios->c_cflag & CSIZE) == CS7)
-		new_lcr |= MAX3107_LCR_WORD_LEN_7;
-	else
-		new_lcr |= MAX3107_LCR_WORD_LEN_8;
-
-	/* Parity */
-	if (termios->c_cflag & PARENB) {
-		new_lcr |= MAX3107_LCR_PARITY_BIT;
-		if (!(termios->c_cflag & PARODD))
-			new_lcr |= MAX3107_LCR_EVENPARITY_BIT;
-	}
-
-	/* Stop bits */
-	if (termios->c_cflag & CSTOPB) {
-		/* 2 stop bits */
-		new_lcr |= MAX3107_LCR_STOPLEN_BIT;
-	}
-
-	/* Mask termios capabilities we don't support */
-	termios->c_cflag &= ~CMSPAR;
-
-	/* Set status ignore mask */
-	s->port.ignore_status_mask = 0;
-	if (termios->c_iflag & IGNPAR)
-		s->port.ignore_status_mask |= MAX3107_ALL_ERRORS;
-
-	/* Set low latency to immediately handle pushed data */
-	s->port.state->port.tty->low_latency = 1;
-
-	/* Get new baud rate generator configuration */
-	baud = tty_get_baud_rate(tty);
-
-	spin_lock_irqsave(&s->data_lock, flags);
-	new_brg = get_new_brg(baud, s);
-	/* if can't find the corrent config, use previous */
-	if (!new_brg) {
-		baud = s->baud;
-		new_brg = s->brg_cfg;
-	}
-	spin_unlock_irqrestore(&s->data_lock, flags);
-	tty_termios_encode_baud_rate(termios, baud, baud);
-	s->baud = baud;
-
-	/* Update timeout according to new baud rate */
-	uart_update_timeout(port, termios->c_cflag, baud);
-
-	spin_lock_irqsave(&s->data_lock, flags);
-	if (s->lcr_reg != new_lcr) {
-		s->lcr_reg = new_lcr;
-		s->lcr_commit = 1;
-	}
-	if (s->brg_cfg != new_brg) {
-		s->brg_cfg = new_brg;
-		s->brg_commit = 1;
-	}
-	spin_unlock_irqrestore(&s->data_lock, flags);
-
-	/* Trigger work thread for doing the actual configuration change */
-	max3107_dowork(s);
-}
-
-/* Port shutdown function */
-static void max3107_shutdown(struct uart_port *port)
-{
-	struct max3107_port *s = container_of(port, struct max3107_port, port);
-
-	if (s->suspended && s->pdata->hw_suspend)
-		s->pdata->hw_suspend(s, 0);
-
-	/* Free the interrupt */
-	free_irq(s->spi->irq, s);
-
-	if (s->workqueue) {
-		/* Flush and destroy work queue */
-		flush_workqueue(s->workqueue);
-		destroy_workqueue(s->workqueue);
-		s->workqueue = NULL;
-	}
-
-	/* Suspend HW */
-	if (s->pdata->hw_suspend)
-		s->pdata->hw_suspend(s, 1);
-}
-
-/* Port startup function */
-static int max3107_startup(struct uart_port *port)
-{
-	struct max3107_port *s = container_of(port, struct max3107_port, port);
-
-	/* Initialize work queue */
-	s->workqueue = create_freezable_workqueue("max3107");
-	if (!s->workqueue) {
-		dev_err(&s->spi->dev, "Workqueue creation failed\n");
-		return -EBUSY;
-	}
-	INIT_WORK(&s->work, max3107_work);
-
-	/* Setup IRQ */
-	if (request_irq(s->spi->irq, max3107_irq, IRQF_TRIGGER_FALLING,
-			"max3107", s)) {
-		dev_err(&s->spi->dev, "IRQ reguest failed\n");
-		destroy_workqueue(s->workqueue);
-		s->workqueue = NULL;
-		return -EBUSY;
-	}
-
-	/* Resume HW */
-	if (s->pdata->hw_suspend)
-		s->pdata->hw_suspend(s, 0);
-
-	/* Init registers */
-	max3107_register_init(s);
-
-	return 0;
-}
-
-/* Port type function */
-static const char *max3107_type(struct uart_port *port)
-{
-	struct max3107_port *s = container_of(port, struct max3107_port, port);
-	return s->spi->modalias;
-}
-
-/* Port release function */
-static void max3107_release_port(struct uart_port *port)
-{
-	/* Do nothing */
-}
-
-/* Port request function */
-static int max3107_request_port(struct uart_port *port)
-{
-	/* Do nothing */
-	return 0;
-}
-
-/* Port config function */
-static void max3107_config_port(struct uart_port *port, int flags)
-{
-	struct max3107_port *s = container_of(port, struct max3107_port, port);
-	s->port.type = PORT_MAX3107;
-}
-
-/* Port verify function */
-static int max3107_verify_port(struct uart_port *port,
-				struct serial_struct *ser)
-{
-	if (ser->type == PORT_UNKNOWN || ser->type == PORT_MAX3107)
-		return 0;
-
-	return -EINVAL;
-}
-
-/* Port stop TX function */
-static void max3107_stop_tx(struct uart_port *port)
-{
-	/* Do nothing */
-}
-
-/* Port break control function */
-static void max3107_break_ctl(struct uart_port *port, int break_state)
-{
-	/* We don't support break control, do nothing */
-}
-
-
-/* Port functions */
-static struct uart_ops max3107_ops = {
-	.tx_empty       = max3107_tx_empty,
-	.set_mctrl      = max3107_set_mctrl,
-	.get_mctrl      = max3107_get_mctrl,
-	.stop_tx        = max3107_stop_tx,
-	.start_tx       = max3107_start_tx,
-	.stop_rx        = max3107_stop_rx,
-	.enable_ms      = max3107_enable_ms,
-	.break_ctl      = max3107_break_ctl,
-	.startup        = max3107_startup,
-	.shutdown       = max3107_shutdown,
-	.set_termios    = max3107_set_termios,
-	.type           = max3107_type,
-	.release_port   = max3107_release_port,
-	.request_port   = max3107_request_port,
-	.config_port    = max3107_config_port,
-	.verify_port    = max3107_verify_port,
-};
-
-/* UART driver data */
-static struct uart_driver max3107_uart_driver = {
-	.owner          = THIS_MODULE,
-	.driver_name    = "ttyMAX",
-	.dev_name       = "ttyMAX",
-	.nr             = 1,
-};
-
-static int driver_registered = 0;
-
-
-
-/* 'Generic' platform data */
-static struct max3107_plat generic_plat_data = {
-	.loopback               = 0,
-	.ext_clk                = 1,
-	.hw_suspend		= max3107_hw_susp,
-	.polled_mode            = 0,
-	.poll_time              = 0,
-};
-
-
-/*******************************************************************/
-
-/**
- *	max3107_probe		-	SPI bus probe entry point
- *	@spi: the spi device
- *
- *	SPI wants us to probe this device and if appropriate claim it.
- *	Perform any platform specific requirements and then initialise
- *	the device.
- */
-
-int max3107_probe(struct spi_device *spi, struct max3107_plat *pdata)
-{
-	struct max3107_port *s;
-	u16 buf[2];	/* Buffer for SPI transfers */
-	int retval;
-
-	pr_info("enter max3107 probe\n");
-
-	/* Allocate port structure */
-	s = kzalloc(sizeof(*s), GFP_KERNEL);
-	if (!s) {
-		pr_err("Allocating port structure failed\n");
-		return -ENOMEM;
-	}
-
-	s->pdata = pdata;
-
-	/* SPI Rx buffer
-	 * +2 for RX FIFO interrupt
-	 * disabling and RX level query
-	 */
-	s->rxbuf = kzalloc(sizeof(u16) * (MAX3107_RX_FIFO_SIZE+2), GFP_KERNEL);
-	if (!s->rxbuf) {
-		pr_err("Allocating RX buffer failed\n");
-		retval = -ENOMEM;
-		goto err_free4;
-	}
-	s->rxstr = kzalloc(sizeof(u8) * MAX3107_RX_FIFO_SIZE, GFP_KERNEL);
-	if (!s->rxstr) {
-		pr_err("Allocating RX buffer failed\n");
-		retval = -ENOMEM;
-		goto err_free3;
-	}
-	/* SPI Tx buffer
-	 * SPI transfer buffer
-	 * +3 for TX FIFO empty
-	 * interrupt disabling and
-	 * enabling and TX enabling
-	 */
-	s->txbuf = kzalloc(sizeof(u16) * MAX3107_TX_FIFO_SIZE + 3, GFP_KERNEL);
-	if (!s->txbuf) {
-		pr_err("Allocating TX buffer failed\n");
-		retval = -ENOMEM;
-		goto err_free2;
-	}
-	/* Initialize shared data lock */
-	spin_lock_init(&s->data_lock);
-
-	/* SPI intializations */
-	dev_set_drvdata(&spi->dev, s);
-	spi->mode = SPI_MODE_0;
-	spi->dev.platform_data = pdata;
-	spi->bits_per_word = 16;
-	s->ext_clk = pdata->ext_clk;
-	s->loopback = pdata->loopback;
-	spi_setup(spi);
-	s->spi = spi;
-
-	/* Check REV ID to ensure we are talking to what we expect */
-	buf[0] = MAX3107_REVID_REG;
-	if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 2)) {
-		dev_err(&s->spi->dev, "SPI transfer for REVID read failed\n");
-		retval = -EIO;
-		goto err_free1;
-	}
-	if ((buf[0] & MAX3107_SPI_RX_DATA_MASK) != MAX3107_REVID1 &&
-		(buf[0] & MAX3107_SPI_RX_DATA_MASK) != MAX3107_REVID2) {
-		dev_err(&s->spi->dev, "REVID %x does not match\n",
-				(buf[0] & MAX3107_SPI_RX_DATA_MASK));
-		retval = -ENODEV;
-		goto err_free1;
-	}
-
-	/* Disable all interrupts */
-	buf[0] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG | 0x0000);
-	buf[0] |= 0x0000;
-
-	/* Configure clock source */
-	buf[1] = (MAX3107_WRITE_BIT | MAX3107_CLKSRC_REG);
-	if (s->ext_clk) {
-		/* External clock */
-		buf[1] |= MAX3107_CLKSRC_EXTCLK_BIT;
-	}
-
-	/* PLL bypass ON */
-	buf[1] |= MAX3107_CLKSRC_PLLBYP_BIT;
-
-	/* Perform SPI transfer */
-	if (max3107_rw(s, (u8 *)buf, NULL, 4)) {
-		dev_err(&s->spi->dev, "SPI transfer for init failed\n");
-		retval = -EIO;
-		goto err_free1;
-	}
-
-	/* Register UART driver */
-	if (!driver_registered) {
-		retval = uart_register_driver(&max3107_uart_driver);
-		if (retval) {
-			dev_err(&s->spi->dev, "Registering UART driver failed\n");
-			goto err_free1;
-		}
-		driver_registered = 1;
-	}
-
-	/* Initialize UART port data */
-	s->port.fifosize = 128;
-	s->port.ops = &max3107_ops;
-	s->port.line = 0;
-	s->port.dev = &spi->dev;
-	s->port.uartclk = 9600;
-	s->port.flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF;
-	s->port.irq = s->spi->irq;
-	s->port.type = PORT_MAX3107;
-
-	/* Add UART port */
-	retval = uart_add_one_port(&max3107_uart_driver, &s->port);
-	if (retval < 0) {
-		dev_err(&s->spi->dev, "Adding UART port failed\n");
-		goto err_free1;
-	}
-
-	if (pdata->configure) {
-		retval = pdata->configure(s);
-		if (retval < 0)
-			goto err_free1;
-	}
-
-	/* Go to suspend mode */
-	if (pdata->hw_suspend)
-		pdata->hw_suspend(s, 1);
-
-	return 0;
-
-err_free1:
-	kfree(s->txbuf);
-err_free2:
-	kfree(s->rxstr);
-err_free3:
-	kfree(s->rxbuf);
-err_free4:
-	kfree(s);
-	return retval;
-}
-EXPORT_SYMBOL_GPL(max3107_probe);
-
-/* Driver remove function */
-int max3107_remove(struct spi_device *spi)
-{
-	struct max3107_port *s = dev_get_drvdata(&spi->dev);
-
-	pr_info("enter max3107 remove\n");
-
-	/* Remove port */
-	if (uart_remove_one_port(&max3107_uart_driver, &s->port))
-		dev_warn(&s->spi->dev, "Removing UART port failed\n");
-
-
-	/* Free TxRx buffer */
-	kfree(s->rxbuf);
-	kfree(s->rxstr);
-	kfree(s->txbuf);
-
-	/* Free port structure */
-	kfree(s);
-
-	return 0;
-}
-EXPORT_SYMBOL_GPL(max3107_remove);
-
-/* Driver suspend function */
-int max3107_suspend(struct spi_device *spi, pm_message_t state)
-{
-#ifdef CONFIG_PM
-	struct max3107_port *s = dev_get_drvdata(&spi->dev);
-
-	pr_debug("enter suspend\n");
-
-	/* Suspend UART port */
-	uart_suspend_port(&max3107_uart_driver, &s->port);
-
-	/* Go to suspend mode */
-	if (s->pdata->hw_suspend)
-		s->pdata->hw_suspend(s, 1);
-#endif	/* CONFIG_PM */
-	return 0;
-}
-EXPORT_SYMBOL_GPL(max3107_suspend);
-
-/* Driver resume function */
-int max3107_resume(struct spi_device *spi)
-{
-#ifdef CONFIG_PM
-	struct max3107_port *s = dev_get_drvdata(&spi->dev);
-
-	pr_debug("enter resume\n");
-
-	/* Resume from suspend */
-	if (s->pdata->hw_suspend)
-		s->pdata->hw_suspend(s, 0);
-
-	/* Resume UART port */
-	uart_resume_port(&max3107_uart_driver, &s->port);
-#endif	/* CONFIG_PM */
-	return 0;
-}
-EXPORT_SYMBOL_GPL(max3107_resume);
-
-static int max3107_probe_generic(struct spi_device *spi)
-{
-	return max3107_probe(spi, &generic_plat_data);
-}
-
-/* Spi driver data */
-static struct spi_driver max3107_driver = {
-	.driver = {
-		.name		= "max3107",
-		.owner		= THIS_MODULE,
-	},
-	.probe		= max3107_probe_generic,
-	.remove		= __devexit_p(max3107_remove),
-	.suspend	= max3107_suspend,
-	.resume		= max3107_resume,
-};
-
-/* Driver init function */
-static int __init max3107_init(void)
-{
-	pr_info("enter max3107 init\n");
-	return spi_register_driver(&max3107_driver);
-}
-
-/* Driver exit function */
-static void __exit max3107_exit(void)
-{
-	pr_info("enter max3107 exit\n");
-	/* Unregister UART driver */
-	if (driver_registered)
-		uart_unregister_driver(&max3107_uart_driver);
-	spi_unregister_driver(&max3107_driver);
-}
-
-module_init(max3107_init);
-module_exit(max3107_exit);
-
-MODULE_DESCRIPTION("MAX3107 driver");
-MODULE_AUTHOR("Aavamobile");
-MODULE_ALIAS("spi:max3107");
-MODULE_LICENSE("GPL v2");
diff --git a/drivers/tty/serial/max3107.h b/drivers/tty/serial/max3107.h
deleted file mode 100644
index 8415fc7..0000000
--- a/drivers/tty/serial/max3107.h
+++ /dev/null
@@ -1,441 +0,0 @@
-/*
- * max3107.h - spi uart protocol driver header for Maxim 3107
- *
- * Copyright (C) Aavamobile 2009
- * Based on serial_max3100.h by Christian Pellegrin
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#ifndef _MAX3107_H
-#define _MAX3107_H
-
-/* Serial error status definitions */
-#define MAX3107_PARITY_ERROR	1
-#define MAX3107_FRAME_ERROR	2
-#define MAX3107_OVERRUN_ERROR	4
-#define MAX3107_ALL_ERRORS	(MAX3107_PARITY_ERROR | \
-				 MAX3107_FRAME_ERROR | \
-				 MAX3107_OVERRUN_ERROR)
-
-/* GPIO definitions */
-#define MAX3107_GPIO_BASE	88
-#define MAX3107_GPIO_COUNT	4
-
-
-/* GPIO connected to chip's reset pin */
-#define MAX3107_RESET_GPIO	87
-
-
-/* Chip reset delay */
-#define MAX3107_RESET_DELAY	10
-
-/* Chip wakeup delay */
-#define MAX3107_WAKEUP_DELAY	50
-
-
-/* Sleep mode definitions */
-#define MAX3107_DISABLE_FORCED_SLEEP	0
-#define MAX3107_ENABLE_FORCED_SLEEP	1
-#define MAX3107_DISABLE_AUTOSLEEP	2
-#define MAX3107_ENABLE_AUTOSLEEP	3
-
-
-/* Definitions for register access with SPI transfers
- *
- * SPI transfer format:
- *
- * Master to slave bits xzzzzzzzyyyyyyyy
- * Slave to master bits aaaaaaaabbbbbbbb
- *
- * where:
- * x = 0 for reads, 1 for writes
- * z = register address
- * y = new register value if write, 0 if read
- * a = unspecified
- * b = register value if read, unspecified if write
- */
-
-/* SPI speed */
-#define MAX3107_SPI_SPEED	(3125000 * 2)
-
-/* Write bit */
-#define MAX3107_WRITE_BIT	(1 << 15)
-
-/* SPI TX data mask */
-#define MAX3107_SPI_RX_DATA_MASK	(0x00ff)
-
-/* SPI RX data mask */
-#define MAX3107_SPI_TX_DATA_MASK	(0x00ff)
-
-/* Register access masks */
-#define MAX3107_RHR_REG			(0x0000) /* RX FIFO */
-#define MAX3107_THR_REG			(0x0000) /* TX FIFO */
-#define MAX3107_IRQEN_REG		(0x0100) /* IRQ enable */
-#define MAX3107_IRQSTS_REG		(0x0200) /* IRQ status */
-#define MAX3107_LSR_IRQEN_REG		(0x0300) /* LSR IRQ enable */
-#define MAX3107_LSR_IRQSTS_REG		(0x0400) /* LSR IRQ status */
-#define MAX3107_SPCHR_IRQEN_REG		(0x0500) /* Special char IRQ enable */
-#define MAX3107_SPCHR_IRQSTS_REG	(0x0600) /* Special char IRQ status */
-#define MAX3107_STS_IRQEN_REG		(0x0700) /* Status IRQ enable */
-#define MAX3107_STS_IRQSTS_REG		(0x0800) /* Status IRQ status */
-#define MAX3107_MODE1_REG		(0x0900) /* MODE1 */
-#define MAX3107_MODE2_REG		(0x0a00) /* MODE2 */
-#define MAX3107_LCR_REG			(0x0b00) /* LCR */
-#define MAX3107_RXTO_REG		(0x0c00) /* RX timeout */
-#define MAX3107_HDPIXDELAY_REG		(0x0d00) /* Auto transceiver delays */
-#define MAX3107_IRDA_REG		(0x0e00) /* IRDA settings */
-#define MAX3107_FLOWLVL_REG		(0x0f00) /* Flow control levels */
-#define MAX3107_FIFOTRIGLVL_REG		(0x1000) /* FIFO IRQ trigger levels */
-#define MAX3107_TXFIFOLVL_REG		(0x1100) /* TX FIFO level */
-#define MAX3107_RXFIFOLVL_REG		(0x1200) /* RX FIFO level */
-#define MAX3107_FLOWCTRL_REG		(0x1300) /* Flow control */
-#define MAX3107_XON1_REG		(0x1400) /* XON1 character */
-#define MAX3107_XON2_REG		(0x1500) /* XON2 character */
-#define MAX3107_XOFF1_REG		(0x1600) /* XOFF1 character */
-#define MAX3107_XOFF2_REG		(0x1700) /* XOFF2 character */
-#define MAX3107_GPIOCFG_REG		(0x1800) /* GPIO config */
-#define MAX3107_GPIODATA_REG		(0x1900) /* GPIO data */
-#define MAX3107_PLLCFG_REG		(0x1a00) /* PLL config */
-#define MAX3107_BRGCFG_REG		(0x1b00) /* Baud rate generator conf */
-#define MAX3107_BRGDIVLSB_REG		(0x1c00) /* Baud rate divisor LSB */
-#define MAX3107_BRGDIVMSB_REG		(0x1d00) /* Baud rate divisor MSB */
-#define MAX3107_CLKSRC_REG		(0x1e00) /* Clock source */
-#define MAX3107_REVID_REG		(0x1f00) /* Revision identification */
-
-/* IRQ register bits */
-#define MAX3107_IRQ_LSR_BIT	(1 << 0) /* LSR interrupt */
-#define MAX3107_IRQ_SPCHR_BIT	(1 << 1) /* Special char interrupt */
-#define MAX3107_IRQ_STS_BIT	(1 << 2) /* Status interrupt */
-#define MAX3107_IRQ_RXFIFO_BIT	(1 << 3) /* RX FIFO interrupt */
-#define MAX3107_IRQ_TXFIFO_BIT	(1 << 4) /* TX FIFO interrupt */
-#define MAX3107_IRQ_TXEMPTY_BIT	(1 << 5) /* TX FIFO empty interrupt */
-#define MAX3107_IRQ_RXEMPTY_BIT	(1 << 6) /* RX FIFO empty interrupt */
-#define MAX3107_IRQ_CTS_BIT	(1 << 7) /* CTS interrupt */
-
-/* LSR register bits */
-#define MAX3107_LSR_RXTO_BIT	(1 << 0) /* RX timeout */
-#define MAX3107_LSR_RXOVR_BIT	(1 << 1) /* RX overrun */
-#define MAX3107_LSR_RXPAR_BIT	(1 << 2) /* RX parity error */
-#define MAX3107_LSR_FRERR_BIT	(1 << 3) /* Frame error */
-#define MAX3107_LSR_RXBRK_BIT	(1 << 4) /* RX break */
-#define MAX3107_LSR_RXNOISE_BIT	(1 << 5) /* RX noise */
-#define MAX3107_LSR_UNDEF6_BIT	(1 << 6) /* Undefined/not used */
-#define MAX3107_LSR_CTS_BIT	(1 << 7) /* CTS pin state */
-
-/* Special character register bits */
-#define MAX3107_SPCHR_XON1_BIT		(1 << 0) /* XON1 character */
-#define MAX3107_SPCHR_XON2_BIT		(1 << 1) /* XON2 character */
-#define MAX3107_SPCHR_XOFF1_BIT		(1 << 2) /* XOFF1 character */
-#define MAX3107_SPCHR_XOFF2_BIT		(1 << 3) /* XOFF2 character */
-#define MAX3107_SPCHR_BREAK_BIT		(1 << 4) /* RX break */
-#define MAX3107_SPCHR_MULTIDROP_BIT	(1 << 5) /* 9-bit multidrop addr char */
-#define MAX3107_SPCHR_UNDEF6_BIT	(1 << 6) /* Undefined/not used */
-#define MAX3107_SPCHR_UNDEF7_BIT	(1 << 7) /* Undefined/not used */
-
-/* Status register bits */
-#define MAX3107_STS_GPIO0_BIT		(1 << 0) /* GPIO 0 interrupt */
-#define MAX3107_STS_GPIO1_BIT		(1 << 1) /* GPIO 1 interrupt */
-#define MAX3107_STS_GPIO2_BIT		(1 << 2) /* GPIO 2 interrupt */
-#define MAX3107_STS_GPIO3_BIT		(1 << 3) /* GPIO 3 interrupt */
-#define MAX3107_STS_UNDEF4_BIT		(1 << 4) /* Undefined/not used */
-#define MAX3107_STS_CLKREADY_BIT	(1 << 5) /* Clock ready */
-#define MAX3107_STS_SLEEP_BIT		(1 << 6) /* Sleep interrupt */
-#define MAX3107_STS_UNDEF7_BIT		(1 << 7) /* Undefined/not used */
-
-/* MODE1 register bits */
-#define MAX3107_MODE1_RXDIS_BIT		(1 << 0) /* RX disable */
-#define MAX3107_MODE1_TXDIS_BIT		(1 << 1) /* TX disable */
-#define MAX3107_MODE1_TXHIZ_BIT		(1 << 2) /* TX pin three-state */
-#define MAX3107_MODE1_RTSHIZ_BIT	(1 << 3) /* RTS pin three-state */
-#define MAX3107_MODE1_TRNSCVCTRL_BIT	(1 << 4) /* Transceiver ctrl enable */
-#define MAX3107_MODE1_FORCESLEEP_BIT	(1 << 5) /* Force sleep mode */
-#define MAX3107_MODE1_AUTOSLEEP_BIT	(1 << 6) /* Auto sleep enable */
-#define MAX3107_MODE1_IRQSEL_BIT	(1 << 7) /* IRQ pin enable */
-
-/* MODE2 register bits */
-#define MAX3107_MODE2_RST_BIT		(1 << 0) /* Chip reset */
-#define MAX3107_MODE2_FIFORST_BIT	(1 << 1) /* FIFO reset */
-#define MAX3107_MODE2_RXTRIGINV_BIT	(1 << 2) /* RX FIFO INT invert */
-#define MAX3107_MODE2_RXEMPTINV_BIT	(1 << 3) /* RX FIFO empty INT invert */
-#define MAX3107_MODE2_SPCHR_BIT		(1 << 4) /* Special chr detect enable */
-#define MAX3107_MODE2_LOOPBACK_BIT	(1 << 5) /* Internal loopback enable */
-#define MAX3107_MODE2_MULTIDROP_BIT	(1 << 6) /* 9-bit multidrop enable */
-#define MAX3107_MODE2_ECHOSUPR_BIT	(1 << 7) /* ECHO suppression enable */
-
-/* LCR register bits */
-#define MAX3107_LCR_LENGTH0_BIT		(1 << 0) /* Word length bit 0 */
-#define MAX3107_LCR_LENGTH1_BIT		(1 << 1) /* Word length bit 1
-						  *
-						  * Word length bits table:
-						  * 00 -> 5 bit words
-						  * 01 -> 6 bit words
-						  * 10 -> 7 bit words
-						  * 11 -> 8 bit words
-						  */
-#define MAX3107_LCR_STOPLEN_BIT		(1 << 2) /* STOP length bit
-						  *
-						  * STOP length bit table:
-						  * 0 -> 1 stop bit
-						  * 1 -> 1-1.5 stop bits if
-						  *      word length is 5,
-						  *      2 stop bits otherwise
-						  */
-#define MAX3107_LCR_PARITY_BIT		(1 << 3) /* Parity bit enable */
-#define MAX3107_LCR_EVENPARITY_BIT	(1 << 4) /* Even parity bit enable */
-#define MAX3107_LCR_FORCEPARITY_BIT	(1 << 5) /* 9-bit multidrop parity */
-#define MAX3107_LCR_TXBREAK_BIT		(1 << 6) /* TX break enable */
-#define MAX3107_LCR_RTS_BIT		(1 << 7) /* RTS pin control */
-#define MAX3107_LCR_WORD_LEN_5		(0x0000)
-#define MAX3107_LCR_WORD_LEN_6		(0x0001)
-#define MAX3107_LCR_WORD_LEN_7		(0x0002)
-#define MAX3107_LCR_WORD_LEN_8		(0x0003)
-
-
-/* IRDA register bits */
-#define MAX3107_IRDA_IRDAEN_BIT		(1 << 0) /* IRDA mode enable */
-#define MAX3107_IRDA_SIR_BIT		(1 << 1) /* SIR mode enable */
-#define MAX3107_IRDA_SHORTIR_BIT	(1 << 2) /* Short SIR mode enable */
-#define MAX3107_IRDA_MIR_BIT		(1 << 3) /* MIR mode enable */
-#define MAX3107_IRDA_RXINV_BIT		(1 << 4) /* RX logic inversion enable */
-#define MAX3107_IRDA_TXINV_BIT		(1 << 5) /* TX logic inversion enable */
-#define MAX3107_IRDA_UNDEF6_BIT		(1 << 6) /* Undefined/not used */
-#define MAX3107_IRDA_UNDEF7_BIT		(1 << 7) /* Undefined/not used */
-
-/* Flow control trigger level register masks */
-#define MAX3107_FLOWLVL_HALT_MASK	(0x000f) /* Flow control halt level */
-#define MAX3107_FLOWLVL_RES_MASK	(0x00f0) /* Flow control resume level */
-#define MAX3107_FLOWLVL_HALT(words)	((words/8) & 0x000f)
-#define MAX3107_FLOWLVL_RES(words)	(((words/8) & 0x000f) << 4)
-
-/* FIFO interrupt trigger level register masks */
-#define MAX3107_FIFOTRIGLVL_TX_MASK	(0x000f) /* TX FIFO trigger level */
-#define MAX3107_FIFOTRIGLVL_RX_MASK	(0x00f0) /* RX FIFO trigger level */
-#define MAX3107_FIFOTRIGLVL_TX(words)	((words/8) & 0x000f)
-#define MAX3107_FIFOTRIGLVL_RX(words)	(((words/8) & 0x000f) << 4)
-
-/* Flow control register bits */
-#define MAX3107_FLOWCTRL_AUTORTS_BIT	(1 << 0) /* Auto RTS flow ctrl enable */
-#define MAX3107_FLOWCTRL_AUTOCTS_BIT	(1 << 1) /* Auto CTS flow ctrl enable */
-#define MAX3107_FLOWCTRL_GPIADDR_BIT	(1 << 2) /* Enables that GPIO inputs
-						  * are used in conjunction with
-						  * XOFF2 for definition of
-						  * special character */
-#define MAX3107_FLOWCTRL_SWFLOWEN_BIT	(1 << 3) /* Auto SW flow ctrl enable */
-#define MAX3107_FLOWCTRL_SWFLOW0_BIT	(1 << 4) /* SWFLOW bit 0 */
-#define MAX3107_FLOWCTRL_SWFLOW1_BIT	(1 << 5) /* SWFLOW bit 1
-						  *
-						  * SWFLOW bits 1 & 0 table:
-						  * 00 -> no transmitter flow
-						  *       control
-						  * 01 -> receiver compares
-						  *       XON2 and XOFF2
-						  *       and controls
-						  *       transmitter
-						  * 10 -> receiver compares
-						  *       XON1 and XOFF1
-						  *       and controls
-						  *       transmitter
-						  * 11 -> receiver compares
-						  *       XON1, XON2, XOFF1 and
-						  *       XOFF2 and controls
-						  *       transmitter
-						  */
-#define MAX3107_FLOWCTRL_SWFLOW2_BIT	(1 << 6) /* SWFLOW bit 2 */
-#define MAX3107_FLOWCTRL_SWFLOW3_BIT	(1 << 7) /* SWFLOW bit 3
-						  *
-						  * SWFLOW bits 3 & 2 table:
-						  * 00 -> no received flow
-						  *       control
-						  * 01 -> transmitter generates
-						  *       XON2 and XOFF2
-						  * 10 -> transmitter generates
-						  *       XON1 and XOFF1
-						  * 11 -> transmitter generates
-						  *       XON1, XON2, XOFF1 and
-						  *       XOFF2
-						  */
-
-/* GPIO configuration register bits */
-#define MAX3107_GPIOCFG_GP0OUT_BIT	(1 << 0) /* GPIO 0 output enable */
-#define MAX3107_GPIOCFG_GP1OUT_BIT	(1 << 1) /* GPIO 1 output enable */
-#define MAX3107_GPIOCFG_GP2OUT_BIT	(1 << 2) /* GPIO 2 output enable */
-#define MAX3107_GPIOCFG_GP3OUT_BIT	(1 << 3) /* GPIO 3 output enable */
-#define MAX3107_GPIOCFG_GP0OD_BIT	(1 << 4) /* GPIO 0 open-drain enable */
-#define MAX3107_GPIOCFG_GP1OD_BIT	(1 << 5) /* GPIO 1 open-drain enable */
-#define MAX3107_GPIOCFG_GP2OD_BIT	(1 << 6) /* GPIO 2 open-drain enable */
-#define MAX3107_GPIOCFG_GP3OD_BIT	(1 << 7) /* GPIO 3 open-drain enable */
-
-/* GPIO DATA register bits */
-#define MAX3107_GPIODATA_GP0OUT_BIT	(1 << 0) /* GPIO 0 output value */
-#define MAX3107_GPIODATA_GP1OUT_BIT	(1 << 1) /* GPIO 1 output value */
-#define MAX3107_GPIODATA_GP2OUT_BIT	(1 << 2) /* GPIO 2 output value */
-#define MAX3107_GPIODATA_GP3OUT_BIT	(1 << 3) /* GPIO 3 output value */
-#define MAX3107_GPIODATA_GP0IN_BIT	(1 << 4) /* GPIO 0 input value */
-#define MAX3107_GPIODATA_GP1IN_BIT	(1 << 5) /* GPIO 1 input value */
-#define MAX3107_GPIODATA_GP2IN_BIT	(1 << 6) /* GPIO 2 input value */
-#define MAX3107_GPIODATA_GP3IN_BIT	(1 << 7) /* GPIO 3 input value */
-
-/* PLL configuration register masks */
-#define MAX3107_PLLCFG_PREDIV_MASK	(0x003f) /* PLL predivision value */
-#define MAX3107_PLLCFG_PLLFACTOR_MASK	(0x00c0) /* PLL multiplication factor */
-
-/* Baud rate generator configuration register masks and bits */
-#define MAX3107_BRGCFG_FRACT_MASK	(0x000f) /* Fractional portion of
-						  * Baud rate generator divisor
-						  */
-#define MAX3107_BRGCFG_2XMODE_BIT	(1 << 4) /* Double baud rate */
-#define MAX3107_BRGCFG_4XMODE_BIT	(1 << 5) /* Quadruple baud rate */
-#define MAX3107_BRGCFG_UNDEF6_BIT	(1 << 6) /* Undefined/not used */
-#define MAX3107_BRGCFG_UNDEF7_BIT	(1 << 7) /* Undefined/not used */
-
-/* Clock source register bits */
-#define MAX3107_CLKSRC_INTOSC_BIT	(1 << 0) /* Internal osc enable */
-#define MAX3107_CLKSRC_CRYST_BIT	(1 << 1) /* Crystal osc enable */
-#define MAX3107_CLKSRC_PLL_BIT		(1 << 2) /* PLL enable */
-#define MAX3107_CLKSRC_PLLBYP_BIT	(1 << 3) /* PLL bypass */
-#define MAX3107_CLKSRC_EXTCLK_BIT	(1 << 4) /* External clock enable */
-#define MAX3107_CLKSRC_UNDEF5_BIT	(1 << 5) /* Undefined/not used */
-#define MAX3107_CLKSRC_UNDEF6_BIT	(1 << 6) /* Undefined/not used */
-#define MAX3107_CLKSRC_CLK2RTS_BIT	(1 << 7) /* Baud clk to RTS pin */
-
-
-/* HW definitions */
-#define MAX3107_RX_FIFO_SIZE	128
-#define MAX3107_TX_FIFO_SIZE	128
-#define MAX3107_REVID1		0x00a0
-#define MAX3107_REVID2		0x00a1
-
-
-/* Baud rate generator configuration values for external clock 13MHz */
-#define MAX3107_BRG13_B300	(0x0A9400 | 0x05)
-#define MAX3107_BRG13_B600	(0x054A00 | 0x03)
-#define MAX3107_BRG13_B1200	(0x02A500 | 0x01)
-#define MAX3107_BRG13_B2400	(0x015200 | 0x09)
-#define MAX3107_BRG13_B4800	(0x00A900 | 0x04)
-#define MAX3107_BRG13_B9600	(0x005400 | 0x0A)
-#define MAX3107_BRG13_B19200	(0x002A00 | 0x05)
-#define MAX3107_BRG13_B38400	(0x001500 | 0x03)
-#define MAX3107_BRG13_B57600	(0x000E00 | 0x02)
-#define MAX3107_BRG13_B115200	(0x000700 | 0x01)
-#define MAX3107_BRG13_B230400	(0x000300 | 0x08)
-#define MAX3107_BRG13_B460800	(0x000100 | 0x0c)
-#define MAX3107_BRG13_B921600	(0x000100 | 0x1c)
-
-/* Baud rate generator configuration values for external clock 26MHz */
-#define MAX3107_BRG26_B300	(0x152800 | 0x0A)
-#define MAX3107_BRG26_B600	(0x0A9400 | 0x05)
-#define MAX3107_BRG26_B1200	(0x054A00 | 0x03)
-#define MAX3107_BRG26_B2400	(0x02A500 | 0x01)
-#define MAX3107_BRG26_B4800	(0x015200 | 0x09)
-#define MAX3107_BRG26_B9600	(0x00A900 | 0x04)
-#define MAX3107_BRG26_B19200	(0x005400 | 0x0A)
-#define MAX3107_BRG26_B38400	(0x002A00 | 0x05)
-#define MAX3107_BRG26_B57600	(0x001C00 | 0x03)
-#define MAX3107_BRG26_B115200	(0x000E00 | 0x02)
-#define MAX3107_BRG26_B230400	(0x000700 | 0x01)
-#define MAX3107_BRG26_B460800	(0x000300 | 0x08)
-#define MAX3107_BRG26_B921600	(0x000100 | 0x0C)
-
-/* Baud rate generator configuration values for internal clock */
-#define MAX3107_BRG13_IB300	(0x008000 | 0x00)
-#define MAX3107_BRG13_IB600	(0x004000 | 0x00)
-#define MAX3107_BRG13_IB1200	(0x002000 | 0x00)
-#define MAX3107_BRG13_IB2400	(0x001000 | 0x00)
-#define MAX3107_BRG13_IB4800	(0x000800 | 0x00)
-#define MAX3107_BRG13_IB9600	(0x000400 | 0x00)
-#define MAX3107_BRG13_IB19200	(0x000200 | 0x00)
-#define MAX3107_BRG13_IB38400	(0x000100 | 0x00)
-#define MAX3107_BRG13_IB57600	(0x000000 | 0x0B)
-#define MAX3107_BRG13_IB115200	(0x000000 | 0x05)
-#define MAX3107_BRG13_IB230400	(0x000000 | 0x03)
-#define MAX3107_BRG13_IB460800	(0x000000 | 0x00)
-#define MAX3107_BRG13_IB921600	(0x000000 | 0x00)
-
-
-struct baud_table {
-	int baud;
-	u32 new_brg;
-};
-
-struct max3107_port {
-	/* UART port structure */
-	struct uart_port port;
-
-	/* SPI device structure */
-	struct spi_device *spi;
-
-#if defined(CONFIG_GPIOLIB)
-	/* GPIO chip structure */
-	struct gpio_chip chip;
-#endif
-
-	/* Workqueue that does all the magic */
-	struct workqueue_struct *workqueue;
-	struct work_struct work;
-
-	/* Lock for shared data */
-	spinlock_t data_lock;
-
-	/* Device configuration */
-	int ext_clk;		/* 1 if external clock used */
-	int loopback;		/* Current loopback mode state */
-	int baud;			/* Current baud rate */
-
-	/* State flags */
-	int suspended;		/* Indicates suspend mode */
-	int tx_fifo_empty;	/* Flag for TX FIFO state */
-	int rx_enabled;		/* Flag for receiver state */
-	int tx_enabled;		/* Flag for transmitter state */
-
-	u16 irqen_reg;		/* Current IRQ enable register value */
-	/* Shared data */
-	u16 mode1_reg;		/* Current mode1 register value*/
-	int mode1_commit;	/* Flag for setting new mode1 register value */
-	u16 lcr_reg;		/* Current LCR register value */
-	int lcr_commit;		/* Flag for setting new LCR register value */
-	u32 brg_cfg;		/* Current Baud rate generator config  */
-	int brg_commit;		/* Flag for setting new baud rate generator
-				 * config
-				 */
-	struct baud_table *baud_tbl;
-	int handle_irq;		/* Indicates that IRQ should be handled */
-
-	/* Rx buffer and str*/
-	u16 *rxbuf;
-	u8  *rxstr;
-	/* Tx buffer*/
-	u16 *txbuf;
-
-	struct max3107_plat *pdata;	/* Platform data */
-};
-
-/* Platform data structure */
-struct max3107_plat {
-	/* Loopback mode enable */
-	int loopback;
-	/* External clock enable */
-	int ext_clk;
-	/* Called during the register initialisation */
-	void (*init)(struct max3107_port *s);
-	/* Called when the port is found and configured */
-	int (*configure)(struct max3107_port *s);
-	/* HW suspend function */
-	void (*hw_suspend) (struct max3107_port *s, int suspend);
-	/* Polling mode enable */
-	int polled_mode;
-	/* Polling period if polling mode enabled */
-	int poll_time;
-};
-
-extern int max3107_rw(struct max3107_port *s, u8 *tx, u8 *rx, int len);
-extern void max3107_hw_susp(struct max3107_port *s, int suspend);
-extern int max3107_probe(struct spi_device *spi, struct max3107_plat *pdata);
-extern int max3107_remove(struct spi_device *spi);
-extern int max3107_suspend(struct spi_device *spi, pm_message_t state);
-extern int max3107_resume(struct spi_device *spi);
-
-#endif /* _LINUX_SERIAL_MAX3107_H */
diff --git a/drivers/tty/serial/max310x.c b/drivers/tty/serial/max310x.c
new file mode 100644
index 0000000..2bc28a5
--- /dev/null
+++ b/drivers/tty/serial/max310x.c
@@ -0,0 +1,1260 @@
+/*
+ *  Maxim (Dallas) MAX3107/8 serial driver
+ *
+ *  Copyright (C) 2012 Alexander Shiyan <shc_work@mail.ru>
+ *
+ *  Based on max3100.c, by Christian Pellegrin <chripell@evolware.org>
+ *  Based on max3110.c, by Feng Tang <feng.tang@intel.com>
+ *  Based on max3107.c, by Aavamobile
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2 of the License, or
+ *  (at your option) any later version.
+ */
+
+/* TODO: MAX3109 support (Dual) */
+/* TODO: MAX14830 support (Quad) */
+
+#include <linux/module.h>
+#include <linux/device.h>
+#include <linux/serial_core.h>
+#include <linux/serial.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/regmap.h>
+#include <linux/gpio.h>
+#include <linux/spi/spi.h>
+#include <linux/platform_data/max310x.h>
+
+#define MAX310X_MAJOR			204
+#define MAX310X_MINOR			209
+
+/* MAX310X register definitions */
+#define MAX310X_RHR_REG			(0x00) /* RX FIFO */
+#define MAX310X_THR_REG			(0x00) /* TX FIFO */
+#define MAX310X_IRQEN_REG		(0x01) /* IRQ enable */
+#define MAX310X_IRQSTS_REG		(0x02) /* IRQ status */
+#define MAX310X_LSR_IRQEN_REG		(0x03) /* LSR IRQ enable */
+#define MAX310X_LSR_IRQSTS_REG		(0x04) /* LSR IRQ status */
+#define MAX310X_SPCHR_IRQEN_REG		(0x05) /* Special char IRQ enable */
+#define MAX310X_SPCHR_IRQSTS_REG	(0x06) /* Special char IRQ status */
+#define MAX310X_STS_IRQEN_REG		(0x07) /* Status IRQ enable */
+#define MAX310X_STS_IRQSTS_REG		(0x08) /* Status IRQ status */
+#define MAX310X_MODE1_REG		(0x09) /* MODE1 */
+#define MAX310X_MODE2_REG		(0x0a) /* MODE2 */
+#define MAX310X_LCR_REG			(0x0b) /* LCR */
+#define MAX310X_RXTO_REG		(0x0c) /* RX timeout */
+#define MAX310X_HDPIXDELAY_REG		(0x0d) /* Auto transceiver delays */
+#define MAX310X_IRDA_REG		(0x0e) /* IRDA settings */
+#define MAX310X_FLOWLVL_REG		(0x0f) /* Flow control levels */
+#define MAX310X_FIFOTRIGLVL_REG		(0x10) /* FIFO IRQ trigger levels */
+#define MAX310X_TXFIFOLVL_REG		(0x11) /* TX FIFO level */
+#define MAX310X_RXFIFOLVL_REG		(0x12) /* RX FIFO level */
+#define MAX310X_FLOWCTRL_REG		(0x13) /* Flow control */
+#define MAX310X_XON1_REG		(0x14) /* XON1 character */
+#define MAX310X_XON2_REG		(0x15) /* XON2 character */
+#define MAX310X_XOFF1_REG		(0x16) /* XOFF1 character */
+#define MAX310X_XOFF2_REG		(0x17) /* XOFF2 character */
+#define MAX310X_GPIOCFG_REG		(0x18) /* GPIO config */
+#define MAX310X_GPIODATA_REG		(0x19) /* GPIO data */
+#define MAX310X_PLLCFG_REG		(0x1a) /* PLL config */
+#define MAX310X_BRGCFG_REG		(0x1b) /* Baud rate generator conf */
+#define MAX310X_BRGDIVLSB_REG		(0x1c) /* Baud rate divisor LSB */
+#define MAX310X_BRGDIVMSB_REG		(0x1d) /* Baud rate divisor MSB */
+#define MAX310X_CLKSRC_REG		(0x1e) /* Clock source */
+/* Only present in MAX3107 */
+#define MAX3107_REVID_REG		(0x1f) /* Revision identification */
+
+/* IRQ register bits */
+#define MAX310X_IRQ_LSR_BIT		(1 << 0) /* LSR interrupt */
+#define MAX310X_IRQ_SPCHR_BIT		(1 << 1) /* Special char interrupt */
+#define MAX310X_IRQ_STS_BIT		(1 << 2) /* Status interrupt */
+#define MAX310X_IRQ_RXFIFO_BIT		(1 << 3) /* RX FIFO interrupt */
+#define MAX310X_IRQ_TXFIFO_BIT		(1 << 4) /* TX FIFO interrupt */
+#define MAX310X_IRQ_TXEMPTY_BIT		(1 << 5) /* TX FIFO empty interrupt */
+#define MAX310X_IRQ_RXEMPTY_BIT		(1 << 6) /* RX FIFO empty interrupt */
+#define MAX310X_IRQ_CTS_BIT		(1 << 7) /* CTS interrupt */
+
+/* LSR register bits */
+#define MAX310X_LSR_RXTO_BIT		(1 << 0) /* RX timeout */
+#define MAX310X_LSR_RXOVR_BIT		(1 << 1) /* RX overrun */
+#define MAX310X_LSR_RXPAR_BIT		(1 << 2) /* RX parity error */
+#define MAX310X_LSR_FRERR_BIT		(1 << 3) /* Frame error */
+#define MAX310X_LSR_RXBRK_BIT		(1 << 4) /* RX break */
+#define MAX310X_LSR_RXNOISE_BIT		(1 << 5) /* RX noise */
+#define MAX310X_LSR_CTS_BIT		(1 << 7) /* CTS pin state */
+
+/* Special character register bits */
+#define MAX310X_SPCHR_XON1_BIT		(1 << 0) /* XON1 character */
+#define MAX310X_SPCHR_XON2_BIT		(1 << 1) /* XON2 character */
+#define MAX310X_SPCHR_XOFF1_BIT		(1 << 2) /* XOFF1 character */
+#define MAX310X_SPCHR_XOFF2_BIT		(1 << 3) /* XOFF2 character */
+#define MAX310X_SPCHR_BREAK_BIT		(1 << 4) /* RX break */
+#define MAX310X_SPCHR_MULTIDROP_BIT	(1 << 5) /* 9-bit multidrop addr char */
+
+/* Status register bits */
+#define MAX310X_STS_GPIO0_BIT		(1 << 0) /* GPIO 0 interrupt */
+#define MAX310X_STS_GPIO1_BIT		(1 << 1) /* GPIO 1 interrupt */
+#define MAX310X_STS_GPIO2_BIT		(1 << 2) /* GPIO 2 interrupt */
+#define MAX310X_STS_GPIO3_BIT		(1 << 3) /* GPIO 3 interrupt */
+#define MAX310X_STS_CLKREADY_BIT	(1 << 5) /* Clock ready */
+#define MAX310X_STS_SLEEP_BIT		(1 << 6) /* Sleep interrupt */
+
+/* MODE1 register bits */
+#define MAX310X_MODE1_RXDIS_BIT		(1 << 0) /* RX disable */
+#define MAX310X_MODE1_TXDIS_BIT		(1 << 1) /* TX disable */
+#define MAX310X_MODE1_TXHIZ_BIT		(1 << 2) /* TX pin three-state */
+#define MAX310X_MODE1_RTSHIZ_BIT	(1 << 3) /* RTS pin three-state */
+#define MAX310X_MODE1_TRNSCVCTRL_BIT	(1 << 4) /* Transceiver ctrl enable */
+#define MAX310X_MODE1_FORCESLEEP_BIT	(1 << 5) /* Force sleep mode */
+#define MAX310X_MODE1_AUTOSLEEP_BIT	(1 << 6) /* Auto sleep enable */
+#define MAX310X_MODE1_IRQSEL_BIT	(1 << 7) /* IRQ pin enable */
+
+/* MODE2 register bits */
+#define MAX310X_MODE2_RST_BIT		(1 << 0) /* Chip reset */
+#define MAX310X_MODE2_FIFORST_BIT	(1 << 1) /* FIFO reset */
+#define MAX310X_MODE2_RXTRIGINV_BIT	(1 << 2) /* RX FIFO INT invert */
+#define MAX310X_MODE2_RXEMPTINV_BIT	(1 << 3) /* RX FIFO empty INT invert */
+#define MAX310X_MODE2_SPCHR_BIT		(1 << 4) /* Special chr detect enable */
+#define MAX310X_MODE2_LOOPBACK_BIT	(1 << 5) /* Internal loopback enable */
+#define MAX310X_MODE2_MULTIDROP_BIT	(1 << 6) /* 9-bit multidrop enable */
+#define MAX310X_MODE2_ECHOSUPR_BIT	(1 << 7) /* ECHO suppression enable */
+
+/* LCR register bits */
+#define MAX310X_LCR_LENGTH0_BIT		(1 << 0) /* Word length bit 0 */
+#define MAX310X_LCR_LENGTH1_BIT		(1 << 1) /* Word length bit 1
+						  *
+						  * Word length bits table:
+						  * 00 -> 5 bit words
+						  * 01 -> 6 bit words
+						  * 10 -> 7 bit words
+						  * 11 -> 8 bit words
+						  */
+#define MAX310X_LCR_STOPLEN_BIT		(1 << 2) /* STOP length bit
+						  *
+						  * STOP length bit table:
+						  * 0 -> 1 stop bit
+						  * 1 -> 1-1.5 stop bits if
+						  *      word length is 5,
+						  *      2 stop bits otherwise
+						  */
+#define MAX310X_LCR_PARITY_BIT		(1 << 3) /* Parity bit enable */
+#define MAX310X_LCR_EVENPARITY_BIT	(1 << 4) /* Even parity bit enable */
+#define MAX310X_LCR_FORCEPARITY_BIT	(1 << 5) /* 9-bit multidrop parity */
+#define MAX310X_LCR_TXBREAK_BIT		(1 << 6) /* TX break enable */
+#define MAX310X_LCR_RTS_BIT		(1 << 7) /* RTS pin control */
+#define MAX310X_LCR_WORD_LEN_5		(0x00)
+#define MAX310X_LCR_WORD_LEN_6		(0x01)
+#define MAX310X_LCR_WORD_LEN_7		(0x02)
+#define MAX310X_LCR_WORD_LEN_8		(0x03)
+
+/* IRDA register bits */
+#define MAX310X_IRDA_IRDAEN_BIT		(1 << 0) /* IRDA mode enable */
+#define MAX310X_IRDA_SIR_BIT		(1 << 1) /* SIR mode enable */
+#define MAX310X_IRDA_SHORTIR_BIT	(1 << 2) /* Short SIR mode enable */
+#define MAX310X_IRDA_MIR_BIT		(1 << 3) /* MIR mode enable */
+#define MAX310X_IRDA_RXINV_BIT		(1 << 4) /* RX logic inversion enable */
+#define MAX310X_IRDA_TXINV_BIT		(1 << 5) /* TX logic inversion enable */
+
+/* Flow control trigger level register masks */
+#define MAX310X_FLOWLVL_HALT_MASK	(0x000f) /* Flow control halt level */
+#define MAX310X_FLOWLVL_RES_MASK	(0x00f0) /* Flow control resume level */
+#define MAX310X_FLOWLVL_HALT(words)	((words / 8) & 0x0f)
+#define MAX310X_FLOWLVL_RES(words)	(((words / 8) & 0x0f) << 4)
+
+/* FIFO interrupt trigger level register masks */
+#define MAX310X_FIFOTRIGLVL_TX_MASK	(0x0f) /* TX FIFO trigger level */
+#define MAX310X_FIFOTRIGLVL_RX_MASK	(0xf0) /* RX FIFO trigger level */
+#define MAX310X_FIFOTRIGLVL_TX(words)	((words / 8) & 0x0f)
+#define MAX310X_FIFOTRIGLVL_RX(words)	(((words / 8) & 0x0f) << 4)
+
+/* Flow control register bits */
+#define MAX310X_FLOWCTRL_AUTORTS_BIT	(1 << 0) /* Auto RTS flow ctrl enable */
+#define MAX310X_FLOWCTRL_AUTOCTS_BIT	(1 << 1) /* Auto CTS flow ctrl enable */
+#define MAX310X_FLOWCTRL_GPIADDR_BIT	(1 << 2) /* Enables that GPIO inputs
+						  * are used in conjunction with
+						  * XOFF2 for definition of
+						  * special character */
+#define MAX310X_FLOWCTRL_SWFLOWEN_BIT	(1 << 3) /* Auto SW flow ctrl enable */
+#define MAX310X_FLOWCTRL_SWFLOW0_BIT	(1 << 4) /* SWFLOW bit 0 */
+#define MAX310X_FLOWCTRL_SWFLOW1_BIT	(1 << 5) /* SWFLOW bit 1
+						  *
+						  * SWFLOW bits 1 & 0 table:
+						  * 00 -> no transmitter flow
+						  *       control
+						  * 01 -> receiver compares
+						  *       XON2 and XOFF2
+						  *       and controls
+						  *       transmitter
+						  * 10 -> receiver compares
+						  *       XON1 and XOFF1
+						  *       and controls
+						  *       transmitter
+						  * 11 -> receiver compares
+						  *       XON1, XON2, XOFF1 and
+						  *       XOFF2 and controls
+						  *       transmitter
+						  */
+#define MAX310X_FLOWCTRL_SWFLOW2_BIT	(1 << 6) /* SWFLOW bit 2 */
+#define MAX310X_FLOWCTRL_SWFLOW3_BIT	(1 << 7) /* SWFLOW bit 3
+						  *
+						  * SWFLOW bits 3 & 2 table:
+						  * 00 -> no received flow
+						  *       control
+						  * 01 -> transmitter generates
+						  *       XON2 and XOFF2
+						  * 10 -> transmitter generates
+						  *       XON1 and XOFF1
+						  * 11 -> transmitter generates
+						  *       XON1, XON2, XOFF1 and
+						  *       XOFF2
+						  */
+
+/* GPIO configuration register bits */
+#define MAX310X_GPIOCFG_GP0OUT_BIT	(1 << 0) /* GPIO 0 output enable */
+#define MAX310X_GPIOCFG_GP1OUT_BIT	(1 << 1) /* GPIO 1 output enable */
+#define MAX310X_GPIOCFG_GP2OUT_BIT	(1 << 2) /* GPIO 2 output enable */
+#define MAX310X_GPIOCFG_GP3OUT_BIT	(1 << 3) /* GPIO 3 output enable */
+#define MAX310X_GPIOCFG_GP0OD_BIT	(1 << 4) /* GPIO 0 open-drain enable */
+#define MAX310X_GPIOCFG_GP1OD_BIT	(1 << 5) /* GPIO 1 open-drain enable */
+#define MAX310X_GPIOCFG_GP2OD_BIT	(1 << 6) /* GPIO 2 open-drain enable */
+#define MAX310X_GPIOCFG_GP3OD_BIT	(1 << 7) /* GPIO 3 open-drain enable */
+
+/* GPIO DATA register bits */
+#define MAX310X_GPIODATA_GP0OUT_BIT	(1 << 0) /* GPIO 0 output value */
+#define MAX310X_GPIODATA_GP1OUT_BIT	(1 << 1) /* GPIO 1 output value */
+#define MAX310X_GPIODATA_GP2OUT_BIT	(1 << 2) /* GPIO 2 output value */
+#define MAX310X_GPIODATA_GP3OUT_BIT	(1 << 3) /* GPIO 3 output value */
+#define MAX310X_GPIODATA_GP0IN_BIT	(1 << 4) /* GPIO 0 input value */
+#define MAX310X_GPIODATA_GP1IN_BIT	(1 << 5) /* GPIO 1 input value */
+#define MAX310X_GPIODATA_GP2IN_BIT	(1 << 6) /* GPIO 2 input value */
+#define MAX310X_GPIODATA_GP3IN_BIT	(1 << 7) /* GPIO 3 input value */
+
+/* PLL configuration register masks */
+#define MAX310X_PLLCFG_PREDIV_MASK	(0x3f) /* PLL predivision value */
+#define MAX310X_PLLCFG_PLLFACTOR_MASK	(0xc0) /* PLL multiplication factor */
+
+/* Baud rate generator configuration register bits */
+#define MAX310X_BRGCFG_2XMODE_BIT	(1 << 4) /* Double baud rate */
+#define MAX310X_BRGCFG_4XMODE_BIT	(1 << 5) /* Quadruple baud rate */
+
+/* Clock source register bits */
+#define MAX310X_CLKSRC_CRYST_BIT	(1 << 1) /* Crystal osc enable */
+#define MAX310X_CLKSRC_PLL_BIT		(1 << 2) /* PLL enable */
+#define MAX310X_CLKSRC_PLLBYP_BIT	(1 << 3) /* PLL bypass */
+#define MAX310X_CLKSRC_EXTCLK_BIT	(1 << 4) /* External clock enable */
+#define MAX310X_CLKSRC_CLK2RTS_BIT	(1 << 7) /* Baud clk to RTS pin */
+
+/* Misc definitions */
+#define MAX310X_FIFO_SIZE		(128)
+
+/* MAX3107 specific */
+#define MAX3107_REV_ID			(0xa0)
+#define MAX3107_REV_MASK		(0xfe)
+
+/* IRQ status bits definitions */
+#define MAX310X_IRQ_TX			(MAX310X_IRQ_TXFIFO_BIT | \
+					 MAX310X_IRQ_TXEMPTY_BIT)
+#define MAX310X_IRQ_RX			(MAX310X_IRQ_RXFIFO_BIT | \
+					 MAX310X_IRQ_RXEMPTY_BIT)
+
+/* Supported chip types */
+enum {
+	MAX310X_TYPE_MAX3107	= 3107,
+	MAX310X_TYPE_MAX3108	= 3108,
+};
+
+struct max310x_port {
+	struct uart_driver	uart;
+	struct uart_port	port;
+
+	const char		*name;
+	int			uartclk;
+
+	unsigned int		nr_gpio;
+#ifdef CONFIG_GPIOLIB
+	struct gpio_chip	gpio;
+#endif
+
+	struct regmap		*regmap;
+	struct regmap_config	regcfg;
+
+	struct workqueue_struct	*wq;
+	struct work_struct	tx_work;
+
+	struct mutex		max310x_mutex;
+
+	struct max310x_pdata	*pdata;
+};
+
+static bool max3107_8_reg_writeable(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case MAX310X_IRQSTS_REG:
+	case MAX310X_LSR_IRQSTS_REG:
+	case MAX310X_SPCHR_IRQSTS_REG:
+	case MAX310X_STS_IRQSTS_REG:
+	case MAX310X_TXFIFOLVL_REG:
+	case MAX310X_RXFIFOLVL_REG:
+	case MAX3107_REVID_REG: /* Only available on MAX3107 */
+		return false;
+	default:
+		break;
+	}
+
+	return true;
+}
+
+static bool max310x_reg_volatile(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case MAX310X_RHR_REG:
+	case MAX310X_IRQSTS_REG:
+	case MAX310X_LSR_IRQSTS_REG:
+	case MAX310X_SPCHR_IRQSTS_REG:
+	case MAX310X_STS_IRQSTS_REG:
+	case MAX310X_TXFIFOLVL_REG:
+	case MAX310X_RXFIFOLVL_REG:
+	case MAX310X_GPIODATA_REG:
+		return true;
+	default:
+		break;
+	}
+
+	return false;
+}
+
+static bool max310x_reg_precious(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case MAX310X_RHR_REG:
+	case MAX310X_IRQSTS_REG:
+	case MAX310X_SPCHR_IRQSTS_REG:
+	case MAX310X_STS_IRQSTS_REG:
+		return true;
+	default:
+		break;
+	}
+
+	return false;
+}
+
+static void max310x_set_baud(struct max310x_port *s, int baud)
+{
+	unsigned int mode = 0, div = s->uartclk / baud;
+
+	if (!(div / 16)) {
+		/* Mode x2 */
+		mode = MAX310X_BRGCFG_2XMODE_BIT;
+		div = (s->uartclk * 2) / baud;
+	}
+
+	if (!(div / 16)) {
+		/* Mode x4 */
+		mode = MAX310X_BRGCFG_4XMODE_BIT;
+		div = (s->uartclk * 4) / baud;
+	}
+
+	regmap_write(s->regmap, MAX310X_BRGDIVMSB_REG,
+		     ((div / 16) >> 8) & 0xff);
+	regmap_write(s->regmap, MAX310X_BRGDIVLSB_REG, (div / 16) & 0xff);
+	regmap_write(s->regmap, MAX310X_BRGCFG_REG, (div % 16) | mode);
+}
+
+static void max310x_wait_pll(struct max310x_port *s)
+{
+	int tryes = 1000;
+
+	/* Wait for PLL only if crystal is used */
+	if (!(s->pdata->driver_flags & MAX310X_EXT_CLK)) {
+		unsigned int sts = 0;
+
+		while (tryes--) {
+			regmap_read(s->regmap, MAX310X_STS_IRQSTS_REG, &sts);
+			if (sts & MAX310X_STS_CLKREADY_BIT)
+				break;
+		}
+	}
+}
+
+static int __devinit max310x_update_best_err(unsigned long f, long *besterr)
+{
+	/* Use baudrate 115200 for calculate error */
+	long err = f % (115200 * 16);
+
+	if ((*besterr < 0) || (*besterr > err)) {
+		*besterr = err;
+		return 0;
+	}
+
+	return 1;
+}
+
+static int __devinit max310x_set_ref_clk(struct max310x_port *s)
+{
+	unsigned int div, clksrc, pllcfg = 0;
+	long besterr = -1;
+	unsigned long fdiv, fmul, bestfreq = s->pdata->frequency;
+
+	/* First, update error without PLL */
+	max310x_update_best_err(s->pdata->frequency, &besterr);
+
+	/* Try all possible PLL dividers */
+	for (div = 1; (div <= 63) && besterr; div++) {
+		fdiv = DIV_ROUND_CLOSEST(s->pdata->frequency, div);
+
+		/* Try multiplier 6 */
+		fmul = fdiv * 6;
+		if ((fdiv >= 500000) && (fdiv <= 800000))
+			if (!max310x_update_best_err(fmul, &besterr)) {
+				pllcfg = (0 << 6) | div;
+				bestfreq = fmul;
+			}
+		/* Try multiplier 48 */
+		fmul = fdiv * 48;
+		if ((fdiv >= 850000) && (fdiv <= 1200000))
+			if (!max310x_update_best_err(fmul, &besterr)) {
+				pllcfg = (1 << 6) | div;
+				bestfreq = fmul;
+			}
+		/* Try multiplier 96 */
+		fmul = fdiv * 96;
+		if ((fdiv >= 425000) && (fdiv <= 1000000))
+			if (!max310x_update_best_err(fmul, &besterr)) {
+				pllcfg = (2 << 6) | div;
+				bestfreq = fmul;
+			}
+		/* Try multiplier 144 */
+		fmul = fdiv * 144;
+		if ((fdiv >= 390000) && (fdiv <= 667000))
+			if (!max310x_update_best_err(fmul, &besterr)) {
+				pllcfg = (3 << 6) | div;
+				bestfreq = fmul;
+			}
+	}
+
+	/* Configure clock source */
+	if (s->pdata->driver_flags & MAX310X_EXT_CLK)
+		clksrc = MAX310X_CLKSRC_EXTCLK_BIT;
+	else
+		clksrc = MAX310X_CLKSRC_CRYST_BIT;
+
+	/* Configure PLL */
+	if (pllcfg) {
+		clksrc |= MAX310X_CLKSRC_PLL_BIT;
+		regmap_write(s->regmap, MAX310X_PLLCFG_REG, pllcfg);
+	} else
+		clksrc |= MAX310X_CLKSRC_PLLBYP_BIT;
+
+	regmap_write(s->regmap, MAX310X_CLKSRC_REG, clksrc);
+
+	if (pllcfg)
+		max310x_wait_pll(s);
+
+	dev_dbg(s->port.dev, "Reference clock set to %lu Hz\n", bestfreq);
+
+	return (int)bestfreq;
+}
+
+static void max310x_handle_rx(struct max310x_port *s, unsigned int rxlen)
+{
+	unsigned int sts = 0, ch = 0, flag;
+	struct tty_struct *tty = tty_port_tty_get(&s->port.state->port);
+
+	if (!tty)
+		return;
+
+	if (unlikely(rxlen >= MAX310X_FIFO_SIZE)) {
+		dev_warn(s->port.dev, "Possible RX FIFO overrun %d\n", rxlen);
+		/* Ensure sanity of RX level */
+		rxlen = MAX310X_FIFO_SIZE;
+	}
+
+	dev_dbg(s->port.dev, "RX Len = %u\n", rxlen);
+
+	while (rxlen--) {
+		regmap_read(s->regmap, MAX310X_RHR_REG, &ch);
+		regmap_read(s->regmap, MAX310X_LSR_IRQSTS_REG, &sts);
+
+		sts &= MAX310X_LSR_RXPAR_BIT | MAX310X_LSR_FRERR_BIT |
+		       MAX310X_LSR_RXOVR_BIT | MAX310X_LSR_RXBRK_BIT;
+
+		s->port.icount.rx++;
+		flag = TTY_NORMAL;
+
+		if (unlikely(sts)) {
+			if (sts & MAX310X_LSR_RXBRK_BIT) {
+				s->port.icount.brk++;
+				if (uart_handle_break(&s->port))
+					continue;
+			} else if (sts & MAX310X_LSR_RXPAR_BIT)
+				s->port.icount.parity++;
+			else if (sts & MAX310X_LSR_FRERR_BIT)
+				s->port.icount.frame++;
+			else if (sts & MAX310X_LSR_RXOVR_BIT)
+				s->port.icount.overrun++;
+
+			sts &= s->port.read_status_mask;
+			if (sts & MAX310X_LSR_RXBRK_BIT)
+				flag = TTY_BREAK;
+			else if (sts & MAX310X_LSR_RXPAR_BIT)
+				flag = TTY_PARITY;
+			else if (sts & MAX310X_LSR_FRERR_BIT)
+				flag = TTY_FRAME;
+			else if (sts & MAX310X_LSR_RXOVR_BIT)
+				flag = TTY_OVERRUN;
+		}
+
+		if (uart_handle_sysrq_char(s->port, ch))
+			continue;
+
+		if (sts & s->port.ignore_status_mask)
+			continue;
+
+		uart_insert_char(&s->port, sts, MAX310X_LSR_RXOVR_BIT,
+				 ch, flag);
+	}
+
+	tty_flip_buffer_push(tty);
+
+	tty_kref_put(tty);
+}
+
+static void max310x_handle_tx(struct max310x_port *s)
+{
+	struct circ_buf *xmit = &s->port.state->xmit;
+	unsigned int txlen = 0, to_send;
+
+	if (unlikely(s->port.x_char)) {
+		regmap_write(s->regmap, MAX310X_THR_REG, s->port.x_char);
+		s->port.icount.tx++;
+		s->port.x_char = 0;
+		return;
+	}
+
+	if (uart_circ_empty(xmit) || uart_tx_stopped(&s->port))
+		return;
+
+	/* Get length of data pending in circular buffer */
+	to_send = uart_circ_chars_pending(xmit);
+	if (likely(to_send)) {
+		/* Limit to size of TX FIFO */
+		regmap_read(s->regmap, MAX310X_TXFIFOLVL_REG, &txlen);
+		txlen = MAX310X_FIFO_SIZE - txlen;
+		to_send = (to_send > txlen) ? txlen : to_send;
+
+		dev_dbg(s->port.dev, "TX Len = %u\n", to_send);
+
+		/* Add data to send */
+		s->port.icount.tx += to_send;
+		while (to_send--) {
+			regmap_write(s->regmap, MAX310X_THR_REG,
+				     xmit->buf[xmit->tail]);
+			xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+		};
+	}
+
+	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+		uart_write_wakeup(&s->port);
+}
+
+static irqreturn_t max310x_ist(int irq, void *dev_id)
+{
+	struct max310x_port *s = (struct max310x_port *)dev_id;
+	unsigned int ists = 0, lsr = 0, rxlen = 0;
+
+	mutex_lock(&s->max310x_mutex);
+
+	for (;;) {
+		/* Read IRQ status & RX FIFO level */
+		regmap_read(s->regmap, MAX310X_IRQSTS_REG, &ists);
+		regmap_read(s->regmap, MAX310X_LSR_IRQSTS_REG, &lsr);
+		regmap_read(s->regmap, MAX310X_RXFIFOLVL_REG, &rxlen);
+		if (!ists && !(lsr & MAX310X_LSR_RXTO_BIT) && !rxlen)
+			break;
+
+		dev_dbg(s->port.dev, "IRQ status: 0x%02x\n", ists);
+
+		if (rxlen)
+			max310x_handle_rx(s, rxlen);
+		if (ists & MAX310X_IRQ_TX)
+			max310x_handle_tx(s);
+		if (ists & MAX310X_IRQ_CTS_BIT)
+			uart_handle_cts_change(&s->port,
+					       !!(lsr & MAX310X_LSR_CTS_BIT));
+	}
+
+	mutex_unlock(&s->max310x_mutex);
+
+	return IRQ_HANDLED;
+}
+
+static void max310x_wq_proc(struct work_struct *ws)
+{
+	struct max310x_port *s = container_of(ws, struct max310x_port, tx_work);
+
+	mutex_lock(&s->max310x_mutex);
+	max310x_handle_tx(s);
+	mutex_unlock(&s->max310x_mutex);
+}
+
+static void max310x_start_tx(struct uart_port *port)
+{
+	struct max310x_port *s = container_of(port, struct max310x_port, port);
+
+	queue_work(s->wq, &s->tx_work);
+}
+
+static void max310x_stop_tx(struct uart_port *port)
+{
+	/* Do nothing */
+}
+
+static void max310x_stop_rx(struct uart_port *port)
+{
+	/* Do nothing */
+}
+
+static unsigned int max310x_tx_empty(struct uart_port *port)
+{
+	unsigned int val = 0;
+	struct max310x_port *s = container_of(port, struct max310x_port, port);
+
+	mutex_lock(&s->max310x_mutex);
+	regmap_read(s->regmap, MAX310X_TXFIFOLVL_REG, &val);
+	mutex_unlock(&s->max310x_mutex);
+
+	return val ? 0 : TIOCSER_TEMT;
+}
+
+static void max310x_enable_ms(struct uart_port *port)
+{
+	/* Modem status not supported */
+}
+
+static unsigned int max310x_get_mctrl(struct uart_port *port)
+{
+	/* DCD and DSR are not wired and CTS/RTS is handled automatically
+	 * so just indicate DSR and CAR asserted
+	 */
+	return TIOCM_DSR | TIOCM_CAR;
+}
+
+static void max310x_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+	/* DCD and DSR are not wired and CTS/RTS is hadnled automatically
+	 * so do nothing
+	 */
+}
+
+static void max310x_break_ctl(struct uart_port *port, int break_state)
+{
+	struct max310x_port *s = container_of(port, struct max310x_port, port);
+
+	mutex_lock(&s->max310x_mutex);
+	regmap_update_bits(s->regmap, MAX310X_LCR_REG,
+			   MAX310X_LCR_TXBREAK_BIT,
+			   break_state ? MAX310X_LCR_TXBREAK_BIT : 0);
+	mutex_unlock(&s->max310x_mutex);
+}
+
+static void max310x_set_termios(struct uart_port *port,
+				struct ktermios *termios,
+				struct ktermios *old)
+{
+	struct max310x_port *s = container_of(port, struct max310x_port, port);
+	unsigned int lcr, flow = 0;
+	int baud;
+
+	mutex_lock(&s->max310x_mutex);
+
+	/* Mask termios capabilities we don't support */
+	termios->c_cflag &= ~CMSPAR;
+	termios->c_iflag &= ~IXANY;
+
+	/* Word size */
+	switch (termios->c_cflag & CSIZE) {
+	case CS5:
+		lcr = MAX310X_LCR_WORD_LEN_5;
+		break;
+	case CS6:
+		lcr = MAX310X_LCR_WORD_LEN_6;
+		break;
+	case CS7:
+		lcr = MAX310X_LCR_WORD_LEN_7;
+		break;
+	case CS8:
+	default:
+		lcr = MAX310X_LCR_WORD_LEN_8;
+		break;
+	}
+
+	/* Parity */
+	if (termios->c_cflag & PARENB) {
+		lcr |= MAX310X_LCR_PARITY_BIT;
+		if (!(termios->c_cflag & PARODD))
+			lcr |= MAX310X_LCR_EVENPARITY_BIT;
+	}
+
+	/* Stop bits */
+	if (termios->c_cflag & CSTOPB)
+		lcr |= MAX310X_LCR_STOPLEN_BIT; /* 2 stops */
+
+	/* Update LCR register */
+	regmap_write(s->regmap, MAX310X_LCR_REG, lcr);
+
+	/* Set read status mask */
+	port->read_status_mask = MAX310X_LSR_RXOVR_BIT;
+	if (termios->c_iflag & INPCK)
+		port->read_status_mask |= MAX310X_LSR_RXPAR_BIT |
+					  MAX310X_LSR_FRERR_BIT;
+	if (termios->c_iflag & (BRKINT | PARMRK))
+		port->read_status_mask |= MAX310X_LSR_RXBRK_BIT;
+
+	/* Set status ignore mask */
+	port->ignore_status_mask = 0;
+	if (termios->c_iflag & IGNBRK)
+		port->ignore_status_mask |= MAX310X_LSR_RXBRK_BIT;
+	if (!(termios->c_cflag & CREAD))
+		port->ignore_status_mask |= MAX310X_LSR_RXPAR_BIT |
+					    MAX310X_LSR_RXOVR_BIT |
+					    MAX310X_LSR_FRERR_BIT |
+					    MAX310X_LSR_RXBRK_BIT;
+
+	/* Configure flow control */
+	regmap_write(s->regmap, MAX310X_XON1_REG, termios->c_cc[VSTART]);
+	regmap_write(s->regmap, MAX310X_XOFF1_REG, termios->c_cc[VSTOP]);
+	if (termios->c_cflag & CRTSCTS)
+		flow |= MAX310X_FLOWCTRL_AUTOCTS_BIT |
+			MAX310X_FLOWCTRL_AUTORTS_BIT;
+	if (termios->c_iflag & IXON)
+		flow |= MAX310X_FLOWCTRL_SWFLOW3_BIT |
+			MAX310X_FLOWCTRL_SWFLOWEN_BIT;
+	if (termios->c_iflag & IXOFF)
+		flow |= MAX310X_FLOWCTRL_SWFLOW1_BIT |
+			MAX310X_FLOWCTRL_SWFLOWEN_BIT;
+	regmap_write(s->regmap, MAX310X_FLOWCTRL_REG, flow);
+
+	/* Get baud rate generator configuration */
+	baud = uart_get_baud_rate(port, termios, old,
+				  port->uartclk / 16 / 0xffff,
+				  port->uartclk / 4);
+
+	/* Setup baudrate generator */
+	max310x_set_baud(s, baud);
+
+	/* Update timeout according to new baud rate */
+	uart_update_timeout(port, termios->c_cflag, baud);
+
+	mutex_unlock(&s->max310x_mutex);
+}
+
+static int max310x_startup(struct uart_port *port)
+{
+	unsigned int val, line = port->line;
+	struct max310x_port *s = container_of(port, struct max310x_port, port);
+
+	if (s->pdata->suspend)
+		s->pdata->suspend(0);
+
+	mutex_lock(&s->max310x_mutex);
+
+	/* Configure baud rate, 9600 as default */
+	max310x_set_baud(s, 9600);
+
+	/* Configure LCR register, 8N1 mode by default */
+	val = MAX310X_LCR_WORD_LEN_8;
+	regmap_write(s->regmap, MAX310X_LCR_REG, val);
+
+	/* Configure MODE1 register */
+	regmap_update_bits(s->regmap, MAX310X_MODE1_REG,
+			   MAX310X_MODE1_TRNSCVCTRL_BIT,
+			   (s->pdata->uart_flags[line] & MAX310X_AUTO_DIR_CTRL)
+			   ? MAX310X_MODE1_TRNSCVCTRL_BIT : 0);
+
+	/* Configure MODE2 register */
+	val = MAX310X_MODE2_RXEMPTINV_BIT;
+	if (s->pdata->uart_flags[line] & MAX310X_LOOPBACK)
+		val |= MAX310X_MODE2_LOOPBACK_BIT;
+	if (s->pdata->uart_flags[line] & MAX310X_ECHO_SUPRESS)
+		val |= MAX310X_MODE2_ECHOSUPR_BIT;
+
+	/* Reset FIFOs */
+	val |= MAX310X_MODE2_FIFORST_BIT;
+	regmap_write(s->regmap, MAX310X_MODE2_REG, val);
+
+	/* Configure FIFO trigger level register */
+	/* RX FIFO trigger for 16 words, TX FIFO trigger for 64 words */
+	val = MAX310X_FIFOTRIGLVL_RX(16) | MAX310X_FIFOTRIGLVL_TX(64);
+	regmap_write(s->regmap, MAX310X_FIFOTRIGLVL_REG, val);
+
+	/* Configure flow control levels */
+	/* Flow control halt level 96, resume level 48 */
+	val = MAX310X_FLOWLVL_RES(48) | MAX310X_FLOWLVL_HALT(96);
+	regmap_write(s->regmap, MAX310X_FLOWLVL_REG, val);
+
+	/* Clear timeout register */
+	regmap_write(s->regmap, MAX310X_RXTO_REG, 0);
+
+	/* Configure LSR interrupt enable register */
+	/* Enable RX timeout interrupt */
+	val = MAX310X_LSR_RXTO_BIT;
+	regmap_write(s->regmap, MAX310X_LSR_IRQEN_REG, val);
+
+	/* Clear FIFO reset */
+	regmap_update_bits(s->regmap, MAX310X_MODE2_REG,
+			   MAX310X_MODE2_FIFORST_BIT, 0);
+
+	/* Clear IRQ status register by reading it */
+	regmap_read(s->regmap, MAX310X_IRQSTS_REG, &val);
+
+	/* Configure interrupt enable register */
+	/* Enable CTS change interrupt */
+	val = MAX310X_IRQ_CTS_BIT;
+	/* Enable RX, TX interrupts */
+	val |= MAX310X_IRQ_RX | MAX310X_IRQ_TX;
+	regmap_write(s->regmap, MAX310X_IRQEN_REG, val);
+
+	mutex_unlock(&s->max310x_mutex);
+
+	return 0;
+}
+
+static void max310x_shutdown(struct uart_port *port)
+{
+	struct max310x_port *s = container_of(port, struct max310x_port, port);
+
+	/* Disable all interrupts */
+	mutex_lock(&s->max310x_mutex);
+	regmap_write(s->regmap, MAX310X_IRQEN_REG, 0);
+	mutex_unlock(&s->max310x_mutex);
+
+	if (s->pdata->suspend)
+		s->pdata->suspend(1);
+}
+
+static const char *max310x_type(struct uart_port *port)
+{
+	struct max310x_port *s = container_of(port, struct max310x_port, port);
+
+	return (port->type == PORT_MAX310X) ? s->name : NULL;
+}
+
+static int max310x_request_port(struct uart_port *port)
+{
+	/* Do nothing */
+	return 0;
+}
+
+static void max310x_release_port(struct uart_port *port)
+{
+	/* Do nothing */
+}
+
+static void max310x_config_port(struct uart_port *port, int flags)
+{
+	if (flags & UART_CONFIG_TYPE)
+		port->type = PORT_MAX310X;
+}
+
+static int max310x_verify_port(struct uart_port *port, struct serial_struct *ser)
+{
+	if ((ser->type == PORT_UNKNOWN) || (ser->type == PORT_MAX310X))
+		return 0;
+	if (ser->irq == port->irq)
+		return 0;
+
+	return -EINVAL;
+}
+
+static struct uart_ops max310x_ops = {
+	.tx_empty	= max310x_tx_empty,
+	.set_mctrl	= max310x_set_mctrl,
+	.get_mctrl	= max310x_get_mctrl,
+	.stop_tx	= max310x_stop_tx,
+	.start_tx	= max310x_start_tx,
+	.stop_rx	= max310x_stop_rx,
+	.enable_ms	= max310x_enable_ms,
+	.break_ctl	= max310x_break_ctl,
+	.startup	= max310x_startup,
+	.shutdown	= max310x_shutdown,
+	.set_termios	= max310x_set_termios,
+	.type		= max310x_type,
+	.request_port	= max310x_request_port,
+	.release_port	= max310x_release_port,
+	.config_port	= max310x_config_port,
+	.verify_port	= max310x_verify_port,
+};
+
+static int max310x_suspend(struct spi_device *spi, pm_message_t state)
+{
+	int ret;
+	struct max310x_port *s = dev_get_drvdata(&spi->dev);
+
+	dev_dbg(&spi->dev, "Suspend\n");
+
+	ret = uart_suspend_port(&s->uart, &s->port);
+
+	mutex_lock(&s->max310x_mutex);
+
+	/* Enable sleep mode */
+	regmap_update_bits(s->regmap, MAX310X_MODE1_REG,
+			   MAX310X_MODE1_FORCESLEEP_BIT,
+			   MAX310X_MODE1_FORCESLEEP_BIT);
+
+	mutex_unlock(&s->max310x_mutex);
+
+	if (s->pdata->suspend)
+		s->pdata->suspend(1);
+
+	return ret;
+}
+
+static int max310x_resume(struct spi_device *spi)
+{
+	struct max310x_port *s = dev_get_drvdata(&spi->dev);
+
+	dev_dbg(&spi->dev, "Resume\n");
+
+	if (s->pdata->suspend)
+		s->pdata->suspend(0);
+
+	mutex_lock(&s->max310x_mutex);
+
+	/* Disable sleep mode */
+	regmap_update_bits(s->regmap, MAX310X_MODE1_REG,
+			   MAX310X_MODE1_FORCESLEEP_BIT,
+			   0);
+
+	max310x_wait_pll(s);
+
+	mutex_unlock(&s->max310x_mutex);
+
+	return uart_resume_port(&s->uart, &s->port);
+}
+
+#ifdef CONFIG_GPIOLIB
+static int max310x_gpio_get(struct gpio_chip *chip, unsigned offset)
+{
+	unsigned int val = 0;
+	struct max310x_port *s = container_of(chip, struct max310x_port, gpio);
+
+	mutex_lock(&s->max310x_mutex);
+	regmap_read(s->regmap, MAX310X_GPIODATA_REG, &val);
+	mutex_unlock(&s->max310x_mutex);
+
+	return !!((val >> 4) & (1 << offset));
+}
+
+static void max310x_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
+{
+	struct max310x_port *s = container_of(chip, struct max310x_port, gpio);
+
+	mutex_lock(&s->max310x_mutex);
+	regmap_update_bits(s->regmap, MAX310X_GPIODATA_REG, 1 << offset, value ?
+							    1 << offset : 0);
+	mutex_unlock(&s->max310x_mutex);
+}
+
+static int max310x_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
+{
+	struct max310x_port *s = container_of(chip, struct max310x_port, gpio);
+
+	mutex_lock(&s->max310x_mutex);
+
+	regmap_update_bits(s->regmap, MAX310X_GPIOCFG_REG, 1 << offset, 0);
+
+	mutex_unlock(&s->max310x_mutex);
+
+	return 0;
+}
+
+static int max310x_gpio_direction_output(struct gpio_chip *chip,
+					 unsigned offset, int value)
+{
+	struct max310x_port *s = container_of(chip, struct max310x_port, gpio);
+
+	mutex_lock(&s->max310x_mutex);
+
+	regmap_update_bits(s->regmap, MAX310X_GPIOCFG_REG, 1 << offset,
+							   1 << offset);
+	regmap_update_bits(s->regmap, MAX310X_GPIODATA_REG, 1 << offset, value ?
+							    1 << offset : 0);
+
+	mutex_unlock(&s->max310x_mutex);
+
+	return 0;
+}
+#endif
+
+/* Generic platform data */
+static struct max310x_pdata generic_plat_data = {
+	.driver_flags	= MAX310X_EXT_CLK,
+	.uart_flags[0]	= MAX310X_ECHO_SUPRESS,
+	.frequency	= 26000000,
+};
+
+static int __devinit max310x_probe(struct spi_device *spi)
+{
+	struct max310x_port *s;
+	struct device *dev = &spi->dev;
+	int chiptype = spi_get_device_id(spi)->driver_data;
+	struct max310x_pdata *pdata = dev->platform_data;
+	unsigned int val = 0;
+	int ret;
+
+	/* Check for IRQ */
+	if (spi->irq <= 0) {
+		dev_err(dev, "No IRQ specified\n");
+		return -ENOTSUPP;
+	}
+
+	/* Alloc port structure */
+	s = devm_kzalloc(dev, sizeof(struct max310x_port), GFP_KERNEL);
+	if (!s) {
+		dev_err(dev, "Error allocating port structure\n");
+		return -ENOMEM;
+	}
+	dev_set_drvdata(dev, s);
+
+	if (!pdata) {
+		dev_warn(dev, "No platform data supplied, using defaults\n");
+		pdata = &generic_plat_data;
+	}
+	s->pdata = pdata;
+
+	/* Individual chip settings */
+	switch (chiptype) {
+	case MAX310X_TYPE_MAX3107:
+		s->name = "MAX3107";
+		s->nr_gpio = 4;
+		s->uart.nr = 1;
+		s->regcfg.max_register = 0x1f;
+		break;
+	case MAX310X_TYPE_MAX3108:
+		s->name = "MAX3108";
+		s->nr_gpio = 4;
+		s->uart.nr = 1;
+		s->regcfg.max_register = 0x1e;
+		break;
+	default:
+		dev_err(dev, "Unsupported chip type %i\n", chiptype);
+		return -ENOTSUPP;
+	}
+
+	/* Check input frequency */
+	if ((pdata->driver_flags & MAX310X_EXT_CLK) &&
+	   ((pdata->frequency < 500000) || (pdata->frequency > 35000000)))
+		goto err_freq;
+	/* Check frequency for quartz */
+	if (!(pdata->driver_flags & MAX310X_EXT_CLK) &&
+	   ((pdata->frequency < 1000000) || (pdata->frequency > 4000000)))
+		goto err_freq;
+
+	mutex_init(&s->max310x_mutex);
+
+	/* Setup SPI bus */
+	spi->mode		= SPI_MODE_0;
+	spi->bits_per_word	= 8;
+	spi->max_speed_hz	= 26000000;
+	spi_setup(spi);
+
+	/* Setup regmap */
+	s->regcfg.reg_bits		= 8;
+	s->regcfg.val_bits		= 8;
+	s->regcfg.read_flag_mask	= 0x00;
+	s->regcfg.write_flag_mask	= 0x80;
+	s->regcfg.cache_type		= REGCACHE_RBTREE;
+	s->regcfg.writeable_reg		= max3107_8_reg_writeable;
+	s->regcfg.volatile_reg		= max310x_reg_volatile;
+	s->regcfg.precious_reg		= max310x_reg_precious;
+	s->regmap = devm_regmap_init_spi(spi, &s->regcfg);
+	if (IS_ERR(s->regmap)) {
+		ret = PTR_ERR(s->regmap);
+		dev_err(dev, "Failed to initialize register map\n");
+		goto err_out;
+	}
+
+	/* Reset chip & check SPI function */
+	ret = regmap_write(s->regmap, MAX310X_MODE2_REG, MAX310X_MODE2_RST_BIT);
+	if (ret) {
+		dev_err(dev, "SPI transfer failed\n");
+		goto err_out;
+	}
+	/* Clear chip reset */
+	regmap_write(s->regmap, MAX310X_MODE2_REG, 0);
+
+	switch (chiptype) {
+	case MAX310X_TYPE_MAX3107:
+		/* Check REV ID to ensure we are talking to what we expect */
+		regmap_read(s->regmap, MAX3107_REVID_REG, &val);
+		if (((val & MAX3107_REV_MASK) != MAX3107_REV_ID)) {
+			dev_err(dev, "%s ID 0x%02x does not match\n",
+				s->name, val);
+			ret = -ENODEV;
+			goto err_out;
+		}
+		break;
+	case MAX310X_TYPE_MAX3108:
+		/* MAX3108 have not REV ID register, we just check default value
+		 * from clocksource register to make sure everything works.
+		 */
+		regmap_read(s->regmap, MAX310X_CLKSRC_REG, &val);
+		if (val != (MAX310X_CLKSRC_EXTCLK_BIT |
+			    MAX310X_CLKSRC_PLLBYP_BIT)) {
+			dev_err(dev, "%s not present\n", s->name);
+			ret = -ENODEV;
+			goto err_out;
+		}
+		break;
+	}
+
+	/* Board specific configure */
+	if (pdata->init)
+		pdata->init();
+	if (pdata->suspend)
+		pdata->suspend(0);
+
+	/* Calculate referecne clock */
+	s->uartclk = max310x_set_ref_clk(s);
+
+	/* Disable all interrupts */
+	regmap_write(s->regmap, MAX310X_IRQEN_REG, 0);
+
+	/* Setup MODE1 register */
+	val = MAX310X_MODE1_IRQSEL_BIT; /* Enable IRQ pin */
+	if (pdata->driver_flags & MAX310X_AUTOSLEEP)
+		val = MAX310X_MODE1_AUTOSLEEP_BIT;
+	regmap_write(s->regmap, MAX310X_MODE1_REG, val);
+
+	/* Setup interrupt */
+	ret = devm_request_threaded_irq(dev, spi->irq, NULL, max310x_ist,
+					IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
+					dev_name(dev), s);
+	if (ret) {
+		dev_err(dev, "Unable to reguest IRQ %i\n", spi->irq);
+		goto err_out;
+	}
+
+	/* Register UART driver */
+	s->uart.owner		= THIS_MODULE;
+	s->uart.driver_name	= dev_name(dev);
+	s->uart.dev_name	= "ttyMAX";
+	s->uart.major		= MAX310X_MAJOR;
+	s->uart.minor		= MAX310X_MINOR;
+	ret = uart_register_driver(&s->uart);
+	if (ret) {
+		dev_err(dev, "Registering UART driver failed\n");
+		goto err_out;
+	}
+
+	/* Initialize workqueue for start TX */
+	s->wq = create_freezable_workqueue(dev_name(dev));
+	INIT_WORK(&s->tx_work, max310x_wq_proc);
+
+	/* Initialize UART port data */
+	s->port.line		= 0;
+	s->port.dev		= dev;
+	s->port.irq		= spi->irq;
+	s->port.type		= PORT_MAX310X;
+	s->port.fifosize	= MAX310X_FIFO_SIZE;
+	s->port.flags		= UPF_SKIP_TEST | UPF_FIXED_TYPE;
+	s->port.iotype		= UPIO_PORT;
+	s->port.membase		= (void __iomem *)0xffffffff; /* Bogus value */
+	s->port.uartclk		= s->uartclk;
+	s->port.ops		= &max310x_ops;
+	uart_add_one_port(&s->uart, &s->port);
+
+#ifdef CONFIG_GPIOLIB
+	/* Setup GPIO cotroller */
+	if (pdata->gpio_base) {
+		s->gpio.owner		= THIS_MODULE;
+		s->gpio.dev		= dev;
+		s->gpio.label		= dev_name(dev);
+		s->gpio.direction_input	= max310x_gpio_direction_input;
+		s->gpio.get		= max310x_gpio_get;
+		s->gpio.direction_output= max310x_gpio_direction_output;
+		s->gpio.set		= max310x_gpio_set;
+		s->gpio.base		= pdata->gpio_base;
+		s->gpio.ngpio		= s->nr_gpio;
+		if (gpiochip_add(&s->gpio)) {
+			/* Indicate that we should not call gpiochip_remove */
+			s->gpio.base = 0;
+		}
+	} else
+		dev_info(dev, "GPIO support not enabled\n");
+#endif
+
+	/* Go to suspend mode */
+	if (pdata->suspend)
+		pdata->suspend(1);
+
+	return 0;
+
+err_freq:
+	dev_err(dev, "Frequency parameter incorrect\n");
+	ret = -EINVAL;
+
+err_out:
+	dev_set_drvdata(dev, NULL);
+
+	return ret;
+}
+
+static int __devexit max310x_remove(struct spi_device *spi)
+{
+	struct device *dev = &spi->dev;
+	struct max310x_port *s = dev_get_drvdata(dev);
+	int ret = 0;
+
+	dev_dbg(dev, "Removing port\n");
+
+	devm_free_irq(dev, s->port.irq, s);
+
+	destroy_workqueue(s->wq);
+
+	uart_remove_one_port(&s->uart, &s->port);
+
+	uart_unregister_driver(&s->uart);
+
+#ifdef CONFIG_GPIOLIB
+	if (s->pdata->gpio_base) {
+		ret = gpiochip_remove(&s->gpio);
+		if (ret)
+			dev_err(dev, "Failed to remove gpio chip: %d\n", ret);
+	}
+#endif
+
+	dev_set_drvdata(dev, NULL);
+
+	if (s->pdata->suspend)
+		s->pdata->suspend(1);
+	if (s->pdata->exit)
+		s->pdata->exit();
+
+	return ret;
+}
+
+static const struct spi_device_id max310x_id_table[] = {
+	{ "max3107",	MAX310X_TYPE_MAX3107 },
+	{ "max3108",	MAX310X_TYPE_MAX3108 },
+};
+MODULE_DEVICE_TABLE(spi, max310x_id_table);
+
+static struct spi_driver max310x_driver = {
+	.driver = {
+		.name	= "max310x",
+		.owner	= THIS_MODULE,
+	},
+	.probe		= max310x_probe,
+	.remove		= __devexit_p(max310x_remove),
+	.suspend	= max310x_suspend,
+	.resume		= max310x_resume,
+	.id_table	= max310x_id_table,
+};
+module_spi_driver(max310x_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Alexander Shiyan <shc_work@mail.ru>");
+MODULE_DESCRIPTION("MAX310X serial driver");
diff --git a/drivers/tty/serial/mpc52xx_uart.c b/drivers/tty/serial/mpc52xx_uart.c
index bedac0d..f19d04e 100644
--- a/drivers/tty/serial/mpc52xx_uart.c
+++ b/drivers/tty/serial/mpc52xx_uart.c
@@ -775,11 +775,15 @@
 	}
 
 	if (new->c_cflag & PARENB) {
+		if (new->c_cflag & CMSPAR)
+			mr1 |= MPC52xx_PSC_MODE_PARFORCE;
+
+		/* With CMSPAR, PARODD also means high parity (same as termios) */
 		mr1 |= (new->c_cflag & PARODD) ?
 			MPC52xx_PSC_MODE_PARODD : MPC52xx_PSC_MODE_PAREVEN;
-	} else
+	} else {
 		mr1 |= MPC52xx_PSC_MODE_PARNONE;
-
+	}
 
 	mr2 = 0;
 
diff --git a/drivers/tty/serial/msm_serial.c b/drivers/tty/serial/msm_serial.c
index 8131e2c..033e0bc 100644
--- a/drivers/tty/serial/msm_serial.c
+++ b/drivers/tty/serial/msm_serial.c
@@ -896,7 +896,7 @@
 			return PTR_ERR(msm_port->clk);
 
 	if (msm_port->is_uartdm)
-		clk_set_rate(msm_port->clk, 7372800);
+		clk_set_rate(msm_port->clk, 1843200);
 
 	port->uartclk = clk_get_rate(msm_port->clk);
 	printk(KERN_INFO "uartclk = %d\n", port->uartclk);
diff --git a/drivers/tty/serial/msm_smd_tty.c b/drivers/tty/serial/msm_smd_tty.c
index b25e6ee..925d1fa 100644
--- a/drivers/tty/serial/msm_smd_tty.c
+++ b/drivers/tty/serial/msm_smd_tty.c
@@ -223,9 +223,11 @@
 		return ret;
 
 	for (i = 0; i < smd_tty_channels_len; i++) {
-		tty_port_init(&smd_tty[smd_tty_channels[i].id].port);
-		smd_tty[smd_tty_channels[i].id].port.ops = &smd_tty_port_ops;
-		tty_register_device(smd_tty_driver, smd_tty_channels[i].id, 0);
+		struct tty_port *port = &smd_tty[smd_tty_channels[i].id].port;
+		tty_port_init(port);
+		port->ops = &smd_tty_port_ops;
+		tty_port_register_device(port, smd_tty_driver,
+				smd_tty_channels[i].id, NULL);
 	}
 
 	return 0;
diff --git a/drivers/tty/serial/mxs-auart.c b/drivers/tty/serial/mxs-auart.c
index 3a667ee..6898413 100644
--- a/drivers/tty/serial/mxs-auart.c
+++ b/drivers/tty/serial/mxs-auart.c
@@ -262,7 +262,7 @@
 
 	ctrl &= ~AUART_CTRL2_RTSEN;
 	if (mctrl & TIOCM_RTS) {
-		if (u->state->port.flags & ASYNC_CTS_FLOW)
+		if (tty_port_cts_enabled(&u->state->port))
 			ctrl |= AUART_CTRL2_RTSEN;
 	}
 
@@ -457,11 +457,11 @@
 
 	writel(AUART_CTRL2_UARTEN, u->membase + AUART_CTRL2_CLR);
 
-	writel(AUART_CTRL0_CLKGATE, u->membase + AUART_CTRL0_SET);
-
 	writel(AUART_INTR_RXIEN | AUART_INTR_RTIEN | AUART_INTR_CTSMIEN,
 			u->membase + AUART_INTR_CLR);
 
+	writel(AUART_CTRL0_CLKGATE, u->membase + AUART_CTRL0_SET);
+
 	clk_disable_unprepare(s->clk);
 }
 
@@ -796,6 +796,7 @@
 
 	auart_port[pdev->id] = NULL;
 
+	put_device(s->dev);
 	clk_put(s->clk);
 	free_irq(s->irq, s);
 	kfree(s);
diff --git a/drivers/tty/serial/of_serial.c b/drivers/tty/serial/of_serial.c
index 34e7187..df443b9 100644
--- a/drivers/tty/serial/of_serial.c
+++ b/drivers/tty/serial/of_serial.c
@@ -105,6 +105,10 @@
 	port->uartclk = clk;
 	port->flags = UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF | UPF_IOREMAP
 		| UPF_FIXED_PORT | UPF_FIXED_TYPE;
+
+	if (of_find_property(np, "no-loopback-test", NULL))
+		port->flags |= UPF_SKIP_TEST;
+
 	port->dev = &ofdev->dev;
 
 	if (type == PORT_TEGRA)
@@ -144,8 +148,15 @@
 	switch (port_type) {
 #ifdef CONFIG_SERIAL_8250
 	case PORT_8250 ... PORT_MAX_8250:
-		ret = serial8250_register_port(&port);
+	{
+		/* For now the of bindings don't support the extra
+		   8250 specific bits */
+		struct uart_8250_port port8250;
+		memset(&port8250, 0, sizeof(port8250));
+		port8250.port = port;
+		ret = serial8250_register_8250_port(&port8250);
 		break;
+	}
 #endif
 #ifdef CONFIG_SERIAL_OF_PLATFORM_NWPSERIAL
 	case PORT_NWPSERIAL:
diff --git a/drivers/tty/serial/omap-serial.c b/drivers/tty/serial/omap-serial.c
index d3cda0c..f175385 100644
--- a/drivers/tty/serial/omap-serial.c
+++ b/drivers/tty/serial/omap-serial.c
@@ -32,16 +32,16 @@
 #include <linux/slab.h>
 #include <linux/tty.h>
 #include <linux/tty_flip.h>
+#include <linux/platform_device.h>
 #include <linux/io.h>
-#include <linux/dma-mapping.h>
 #include <linux/clk.h>
 #include <linux/serial_core.h>
 #include <linux/irq.h>
 #include <linux/pm_runtime.h>
 #include <linux/of.h>
+#include <linux/gpio.h>
+#include <linux/pinctrl/consumer.h>
 
-#include <plat/dma.h>
-#include <plat/dmtimer.h>
 #include <plat/omap-serial.h>
 
 #define UART_BUILD_REVISION(x, y)	(((x) << 8) | (y))
@@ -57,8 +57,8 @@
 #define OMAP_UART_SCR_RX_TRIG_GRANU1_MASK		(1 << 7)
 
 /* FCR register bitmasks */
-#define OMAP_UART_FCR_RX_FIFO_TRIG_SHIFT		6
 #define OMAP_UART_FCR_RX_FIFO_TRIG_MASK			(0x3 << 6)
+#define OMAP_UART_FCR_TX_FIFO_TRIG_MASK			(0x3 << 4)
 
 /* MVR register bitmasks */
 #define OMAP_UART_MVR_SCHEME_SHIFT	30
@@ -71,12 +71,52 @@
 #define OMAP_UART_MVR_MAJ_SHIFT		8
 #define OMAP_UART_MVR_MIN_MASK		0x3f
 
+struct uart_omap_port {
+	struct uart_port	port;
+	struct uart_omap_dma	uart_dma;
+	struct device		*dev;
+
+	unsigned char		ier;
+	unsigned char		lcr;
+	unsigned char		mcr;
+	unsigned char		fcr;
+	unsigned char		efr;
+	unsigned char		dll;
+	unsigned char		dlh;
+	unsigned char		mdr1;
+	unsigned char		scr;
+
+	int			use_dma;
+	/*
+	 * Some bits in registers are cleared on a read, so they must
+	 * be saved whenever the register is read but the bits will not
+	 * be immediately processed.
+	 */
+	unsigned int		lsr_break_flag;
+	unsigned char		msr_saved_flags;
+	char			name[20];
+	unsigned long		port_activity;
+	u32			context_loss_cnt;
+	u32			errata;
+	u8			wakeups_enabled;
+	unsigned int		irq_pending:1;
+
+	int			DTR_gpio;
+	int			DTR_inverted;
+	int			DTR_active;
+
+	struct pm_qos_request	pm_qos_request;
+	u32			latency;
+	u32			calc_latency;
+	struct work_struct	qos_work;
+	struct pinctrl		*pins;
+};
+
+#define to_uart_omap_port(p)	((container_of((p), struct uart_omap_port, port)))
+
 static struct uart_omap_port *ui[OMAP_MAX_HSUART_PORTS];
 
 /* Forward declaration of functions */
-static void uart_tx_dma_callback(int lch, u16 ch_status, void *data);
-static void serial_omap_rxdma_poll(unsigned long uart_no);
-static int serial_omap_start_rxdma(struct uart_omap_port *up);
 static void serial_omap_mdr1_errataset(struct uart_omap_port *up, u8 mdr1);
 
 static struct workqueue_struct *serial_omap_uart_wq;
@@ -101,6 +141,46 @@
 	serial_out(up, UART_FCR, 0);
 }
 
+static int serial_omap_get_context_loss_count(struct uart_omap_port *up)
+{
+	struct omap_uart_port_info *pdata = up->dev->platform_data;
+
+	if (!pdata || !pdata->get_context_loss_count)
+		return 0;
+
+	return pdata->get_context_loss_count(up->dev);
+}
+
+static void serial_omap_set_forceidle(struct uart_omap_port *up)
+{
+	struct omap_uart_port_info *pdata = up->dev->platform_data;
+
+	if (!pdata || !pdata->set_forceidle)
+		return;
+
+	pdata->set_forceidle(up->dev);
+}
+
+static void serial_omap_set_noidle(struct uart_omap_port *up)
+{
+	struct omap_uart_port_info *pdata = up->dev->platform_data;
+
+	if (!pdata || !pdata->set_noidle)
+		return;
+
+	pdata->set_noidle(up->dev);
+}
+
+static void serial_omap_enable_wakeup(struct uart_omap_port *up, bool enable)
+{
+	struct omap_uart_port_info *pdata = up->dev->platform_data;
+
+	if (!pdata || !pdata->enable_wakeup)
+		return;
+
+	pdata->enable_wakeup(up->dev, enable);
+}
+
 /*
  * serial_omap_get_divisor - calculate divisor value
  * @port: uart port info
@@ -126,151 +206,55 @@
 	return port->uartclk/(baud * divisor);
 }
 
-static void serial_omap_stop_rxdma(struct uart_omap_port *up)
-{
-	if (up->uart_dma.rx_dma_used) {
-		del_timer(&up->uart_dma.rx_timer);
-		omap_stop_dma(up->uart_dma.rx_dma_channel);
-		omap_free_dma(up->uart_dma.rx_dma_channel);
-		up->uart_dma.rx_dma_channel = OMAP_UART_DMA_CH_FREE;
-		up->uart_dma.rx_dma_used = false;
-		pm_runtime_mark_last_busy(&up->pdev->dev);
-		pm_runtime_put_autosuspend(&up->pdev->dev);
-	}
-}
-
 static void serial_omap_enable_ms(struct uart_port *port)
 {
-	struct uart_omap_port *up = (struct uart_omap_port *)port;
+	struct uart_omap_port *up = to_uart_omap_port(port);
 
 	dev_dbg(up->port.dev, "serial_omap_enable_ms+%d\n", up->port.line);
 
-	pm_runtime_get_sync(&up->pdev->dev);
+	pm_runtime_get_sync(up->dev);
 	up->ier |= UART_IER_MSI;
 	serial_out(up, UART_IER, up->ier);
-	pm_runtime_put(&up->pdev->dev);
+	pm_runtime_mark_last_busy(up->dev);
+	pm_runtime_put_autosuspend(up->dev);
 }
 
 static void serial_omap_stop_tx(struct uart_port *port)
 {
-	struct uart_omap_port *up = (struct uart_omap_port *)port;
-	struct omap_uart_port_info *pdata = up->pdev->dev.platform_data;
+	struct uart_omap_port *up = to_uart_omap_port(port);
 
-	if (up->use_dma &&
-		up->uart_dma.tx_dma_channel != OMAP_UART_DMA_CH_FREE) {
-		/*
-		 * Check if dma is still active. If yes do nothing,
-		 * return. Else stop dma
-		 */
-		if (omap_get_dma_active_status(up->uart_dma.tx_dma_channel))
-			return;
-		omap_stop_dma(up->uart_dma.tx_dma_channel);
-		omap_free_dma(up->uart_dma.tx_dma_channel);
-		up->uart_dma.tx_dma_channel = OMAP_UART_DMA_CH_FREE;
-		pm_runtime_mark_last_busy(&up->pdev->dev);
-		pm_runtime_put_autosuspend(&up->pdev->dev);
-	}
-
-	pm_runtime_get_sync(&up->pdev->dev);
+	pm_runtime_get_sync(up->dev);
 	if (up->ier & UART_IER_THRI) {
 		up->ier &= ~UART_IER_THRI;
 		serial_out(up, UART_IER, up->ier);
 	}
 
-	if (!up->use_dma && pdata && pdata->set_forceidle)
-		pdata->set_forceidle(up->pdev);
+	serial_omap_set_forceidle(up);
 
-	pm_runtime_mark_last_busy(&up->pdev->dev);
-	pm_runtime_put_autosuspend(&up->pdev->dev);
+	pm_runtime_mark_last_busy(up->dev);
+	pm_runtime_put_autosuspend(up->dev);
 }
 
 static void serial_omap_stop_rx(struct uart_port *port)
 {
-	struct uart_omap_port *up = (struct uart_omap_port *)port;
+	struct uart_omap_port *up = to_uart_omap_port(port);
 
-	pm_runtime_get_sync(&up->pdev->dev);
-	if (up->use_dma)
-		serial_omap_stop_rxdma(up);
+	pm_runtime_get_sync(up->dev);
 	up->ier &= ~UART_IER_RLSI;
 	up->port.read_status_mask &= ~UART_LSR_DR;
 	serial_out(up, UART_IER, up->ier);
-	pm_runtime_mark_last_busy(&up->pdev->dev);
-	pm_runtime_put_autosuspend(&up->pdev->dev);
+	pm_runtime_mark_last_busy(up->dev);
+	pm_runtime_put_autosuspend(up->dev);
 }
 
-static inline void receive_chars(struct uart_omap_port *up,
-		unsigned int *status)
-{
-	struct tty_struct *tty = up->port.state->port.tty;
-	unsigned int flag, lsr = *status;
-	unsigned char ch = 0;
-	int max_count = 256;
-
-	do {
-		if (likely(lsr & UART_LSR_DR))
-			ch = serial_in(up, UART_RX);
-		flag = TTY_NORMAL;
-		up->port.icount.rx++;
-
-		if (unlikely(lsr & UART_LSR_BRK_ERROR_BITS)) {
-			/*
-			 * For statistics only
-			 */
-			if (lsr & UART_LSR_BI) {
-				lsr &= ~(UART_LSR_FE | UART_LSR_PE);
-				up->port.icount.brk++;
-				/*
-				 * We do the SysRQ and SAK checking
-				 * here because otherwise the break
-				 * may get masked by ignore_status_mask
-				 * or read_status_mask.
-				 */
-				if (uart_handle_break(&up->port))
-					goto ignore_char;
-			} else if (lsr & UART_LSR_PE) {
-				up->port.icount.parity++;
-			} else if (lsr & UART_LSR_FE) {
-				up->port.icount.frame++;
-			}
-
-			if (lsr & UART_LSR_OE)
-				up->port.icount.overrun++;
-
-			/*
-			 * Mask off conditions which should be ignored.
-			 */
-			lsr &= up->port.read_status_mask;
-
-#ifdef CONFIG_SERIAL_OMAP_CONSOLE
-			if (up->port.line == up->port.cons->index) {
-				/* Recover the break flag from console xmit */
-				lsr |= up->lsr_break_flag;
-			}
-#endif
-			if (lsr & UART_LSR_BI)
-				flag = TTY_BREAK;
-			else if (lsr & UART_LSR_PE)
-				flag = TTY_PARITY;
-			else if (lsr & UART_LSR_FE)
-				flag = TTY_FRAME;
-		}
-
-		if (uart_handle_sysrq_char(&up->port, ch))
-			goto ignore_char;
-		uart_insert_char(&up->port, lsr, UART_LSR_OE, ch, flag);
-ignore_char:
-		lsr = serial_in(up, UART_LSR);
-	} while ((lsr & (UART_LSR_DR | UART_LSR_BI)) && (max_count-- > 0));
-	spin_unlock(&up->port.lock);
-	tty_flip_buffer_push(tty);
-	spin_lock(&up->port.lock);
-}
-
-static void transmit_chars(struct uart_omap_port *up)
+static void transmit_chars(struct uart_omap_port *up, unsigned int lsr)
 {
 	struct circ_buf *xmit = &up->port.state->xmit;
 	int count;
 
+	if (!(lsr & UART_LSR_THRE))
+		return;
+
 	if (up->port.x_char) {
 		serial_out(up, UART_TX, up->port.x_char);
 		up->port.icount.tx++;
@@ -290,8 +274,11 @@
 			break;
 	} while (--count > 0);
 
-	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) {
+		spin_unlock(&up->port.lock);
 		uart_write_wakeup(&up->port);
+		spin_lock(&up->port.lock);
+	}
 
 	if (uart_circ_empty(xmit))
 		serial_omap_stop_tx(&up->port);
@@ -307,70 +294,13 @@
 
 static void serial_omap_start_tx(struct uart_port *port)
 {
-	struct uart_omap_port *up = (struct uart_omap_port *)port;
-	struct omap_uart_port_info *pdata = up->pdev->dev.platform_data;
-	struct circ_buf *xmit;
-	unsigned int start;
-	int ret = 0;
+	struct uart_omap_port *up = to_uart_omap_port(port);
 
-	if (!up->use_dma) {
-		pm_runtime_get_sync(&up->pdev->dev);
-		serial_omap_enable_ier_thri(up);
-		if (pdata && pdata->set_noidle)
-			pdata->set_noidle(up->pdev);
-		pm_runtime_mark_last_busy(&up->pdev->dev);
-		pm_runtime_put_autosuspend(&up->pdev->dev);
-		return;
-	}
-
-	if (up->uart_dma.tx_dma_used)
-		return;
-
-	xmit = &up->port.state->xmit;
-
-	if (up->uart_dma.tx_dma_channel == OMAP_UART_DMA_CH_FREE) {
-		pm_runtime_get_sync(&up->pdev->dev);
-		ret = omap_request_dma(up->uart_dma.uart_dma_tx,
-				"UART Tx DMA",
-				(void *)uart_tx_dma_callback, up,
-				&(up->uart_dma.tx_dma_channel));
-
-		if (ret < 0) {
-			serial_omap_enable_ier_thri(up);
-			return;
-		}
-	}
-	spin_lock(&(up->uart_dma.tx_lock));
-	up->uart_dma.tx_dma_used = true;
-	spin_unlock(&(up->uart_dma.tx_lock));
-
-	start = up->uart_dma.tx_buf_dma_phys +
-				(xmit->tail & (UART_XMIT_SIZE - 1));
-
-	up->uart_dma.tx_buf_size = uart_circ_chars_pending(xmit);
-	/*
-	 * It is a circular buffer. See if the buffer has wounded back.
-	 * If yes it will have to be transferred in two separate dma
-	 * transfers
-	 */
-	if (start + up->uart_dma.tx_buf_size >=
-			up->uart_dma.tx_buf_dma_phys + UART_XMIT_SIZE)
-		up->uart_dma.tx_buf_size =
-			(up->uart_dma.tx_buf_dma_phys +
-			UART_XMIT_SIZE) - start;
-
-	omap_set_dma_dest_params(up->uart_dma.tx_dma_channel, 0,
-				OMAP_DMA_AMODE_CONSTANT,
-				up->uart_dma.uart_base, 0, 0);
-	omap_set_dma_src_params(up->uart_dma.tx_dma_channel, 0,
-				OMAP_DMA_AMODE_POST_INC, start, 0, 0);
-	omap_set_dma_transfer_params(up->uart_dma.tx_dma_channel,
-				OMAP_DMA_DATA_TYPE_S8,
-				up->uart_dma.tx_buf_size, 1,
-				OMAP_DMA_SYNC_ELEMENT,
-				up->uart_dma.uart_dma_tx, 0);
-	/* FIXME: Cache maintenance needed here? */
-	omap_start_dma(up->uart_dma.tx_dma_channel);
+	pm_runtime_get_sync(up->dev);
+	serial_omap_enable_ier_thri(up);
+	serial_omap_set_noidle(up);
+	pm_runtime_mark_last_busy(up->dev);
+	pm_runtime_put_autosuspend(up->dev);
 }
 
 static unsigned int check_modem_status(struct uart_omap_port *up)
@@ -401,76 +331,158 @@
 	return status;
 }
 
+static void serial_omap_rlsi(struct uart_omap_port *up, unsigned int lsr)
+{
+	unsigned int flag;
+
+	up->port.icount.rx++;
+	flag = TTY_NORMAL;
+
+	if (lsr & UART_LSR_BI) {
+		flag = TTY_BREAK;
+		lsr &= ~(UART_LSR_FE | UART_LSR_PE);
+		up->port.icount.brk++;
+		/*
+		 * We do the SysRQ and SAK checking
+		 * here because otherwise the break
+		 * may get masked by ignore_status_mask
+		 * or read_status_mask.
+		 */
+		if (uart_handle_break(&up->port))
+			return;
+
+	}
+
+	if (lsr & UART_LSR_PE) {
+		flag = TTY_PARITY;
+		up->port.icount.parity++;
+	}
+
+	if (lsr & UART_LSR_FE) {
+		flag = TTY_FRAME;
+		up->port.icount.frame++;
+	}
+
+	if (lsr & UART_LSR_OE)
+		up->port.icount.overrun++;
+
+#ifdef CONFIG_SERIAL_OMAP_CONSOLE
+	if (up->port.line == up->port.cons->index) {
+		/* Recover the break flag from console xmit */
+		lsr |= up->lsr_break_flag;
+	}
+#endif
+	uart_insert_char(&up->port, lsr, UART_LSR_OE, 0, flag);
+}
+
+static void serial_omap_rdi(struct uart_omap_port *up, unsigned int lsr)
+{
+	unsigned char ch = 0;
+	unsigned int flag;
+
+	if (!(lsr & UART_LSR_DR))
+		return;
+
+	ch = serial_in(up, UART_RX);
+	flag = TTY_NORMAL;
+	up->port.icount.rx++;
+
+	if (uart_handle_sysrq_char(&up->port, ch))
+		return;
+
+	uart_insert_char(&up->port, lsr, UART_LSR_OE, ch, flag);
+}
+
 /**
  * serial_omap_irq() - This handles the interrupt from one port
  * @irq: uart port irq number
  * @dev_id: uart port info
  */
-static inline irqreturn_t serial_omap_irq(int irq, void *dev_id)
+static irqreturn_t serial_omap_irq(int irq, void *dev_id)
 {
 	struct uart_omap_port *up = dev_id;
+	struct tty_struct *tty = up->port.state->port.tty;
 	unsigned int iir, lsr;
-	unsigned long flags;
+	unsigned int type;
+	irqreturn_t ret = IRQ_NONE;
+	int max_count = 256;
 
-	pm_runtime_get_sync(&up->pdev->dev);
-	iir = serial_in(up, UART_IIR);
-	if (iir & UART_IIR_NO_INT) {
-		pm_runtime_mark_last_busy(&up->pdev->dev);
-		pm_runtime_put_autosuspend(&up->pdev->dev);
-		return IRQ_NONE;
-	}
+	spin_lock(&up->port.lock);
+	pm_runtime_get_sync(up->dev);
 
-	spin_lock_irqsave(&up->port.lock, flags);
-	lsr = serial_in(up, UART_LSR);
-	if (iir & UART_IIR_RLSI) {
-		if (!up->use_dma) {
-			if (lsr & UART_LSR_DR)
-				receive_chars(up, &lsr);
-		} else {
-			up->ier &= ~(UART_IER_RDI | UART_IER_RLSI);
-			serial_out(up, UART_IER, up->ier);
-			if ((serial_omap_start_rxdma(up) != 0) &&
-					(lsr & UART_LSR_DR))
-				receive_chars(up, &lsr);
+	do {
+		iir = serial_in(up, UART_IIR);
+		if (iir & UART_IIR_NO_INT)
+			break;
+
+		ret = IRQ_HANDLED;
+		lsr = serial_in(up, UART_LSR);
+
+		/* extract IRQ type from IIR register */
+		type = iir & 0x3e;
+
+		switch (type) {
+		case UART_IIR_MSI:
+			check_modem_status(up);
+			break;
+		case UART_IIR_THRI:
+			transmit_chars(up, lsr);
+			break;
+		case UART_IIR_RX_TIMEOUT:
+			/* FALLTHROUGH */
+		case UART_IIR_RDI:
+			serial_omap_rdi(up, lsr);
+			break;
+		case UART_IIR_RLSI:
+			serial_omap_rlsi(up, lsr);
+			break;
+		case UART_IIR_CTS_RTS_DSR:
+			/* simply try again */
+			break;
+		case UART_IIR_XOFF:
+			/* FALLTHROUGH */
+		default:
+			break;
 		}
-	}
+	} while (!(iir & UART_IIR_NO_INT) && max_count--);
 
-	check_modem_status(up);
-	if ((lsr & UART_LSR_THRE) && (iir & UART_IIR_THRI))
-		transmit_chars(up);
+	spin_unlock(&up->port.lock);
 
-	spin_unlock_irqrestore(&up->port.lock, flags);
-	pm_runtime_mark_last_busy(&up->pdev->dev);
-	pm_runtime_put_autosuspend(&up->pdev->dev);
+	tty_flip_buffer_push(tty);
 
+	pm_runtime_mark_last_busy(up->dev);
+	pm_runtime_put_autosuspend(up->dev);
 	up->port_activity = jiffies;
-	return IRQ_HANDLED;
+
+	return ret;
 }
 
 static unsigned int serial_omap_tx_empty(struct uart_port *port)
 {
-	struct uart_omap_port *up = (struct uart_omap_port *)port;
+	struct uart_omap_port *up = to_uart_omap_port(port);
 	unsigned long flags = 0;
 	unsigned int ret = 0;
 
-	pm_runtime_get_sync(&up->pdev->dev);
+	pm_runtime_get_sync(up->dev);
 	dev_dbg(up->port.dev, "serial_omap_tx_empty+%d\n", up->port.line);
 	spin_lock_irqsave(&up->port.lock, flags);
 	ret = serial_in(up, UART_LSR) & UART_LSR_TEMT ? TIOCSER_TEMT : 0;
 	spin_unlock_irqrestore(&up->port.lock, flags);
-	pm_runtime_put(&up->pdev->dev);
+	pm_runtime_mark_last_busy(up->dev);
+	pm_runtime_put_autosuspend(up->dev);
 	return ret;
 }
 
 static unsigned int serial_omap_get_mctrl(struct uart_port *port)
 {
-	struct uart_omap_port *up = (struct uart_omap_port *)port;
+	struct uart_omap_port *up = to_uart_omap_port(port);
 	unsigned int status;
 	unsigned int ret = 0;
 
-	pm_runtime_get_sync(&up->pdev->dev);
+	pm_runtime_get_sync(up->dev);
 	status = check_modem_status(up);
-	pm_runtime_put(&up->pdev->dev);
+	pm_runtime_mark_last_busy(up->dev);
+	pm_runtime_put_autosuspend(up->dev);
 
 	dev_dbg(up->port.dev, "serial_omap_get_mctrl+%d\n", up->port.line);
 
@@ -487,7 +499,7 @@
 
 static void serial_omap_set_mctrl(struct uart_port *port, unsigned int mctrl)
 {
-	struct uart_omap_port *up = (struct uart_omap_port *)port;
+	struct uart_omap_port *up = to_uart_omap_port(port);
 	unsigned char mcr = 0;
 
 	dev_dbg(up->port.dev, "serial_omap_set_mctrl+%d\n", up->port.line);
@@ -502,20 +514,31 @@
 	if (mctrl & TIOCM_LOOP)
 		mcr |= UART_MCR_LOOP;
 
-	pm_runtime_get_sync(&up->pdev->dev);
+	pm_runtime_get_sync(up->dev);
 	up->mcr = serial_in(up, UART_MCR);
 	up->mcr |= mcr;
 	serial_out(up, UART_MCR, up->mcr);
-	pm_runtime_put(&up->pdev->dev);
+	pm_runtime_mark_last_busy(up->dev);
+	pm_runtime_put_autosuspend(up->dev);
+
+	if (gpio_is_valid(up->DTR_gpio) &&
+	    !!(mctrl & TIOCM_DTR) != up->DTR_active) {
+		up->DTR_active = !up->DTR_active;
+		if (gpio_cansleep(up->DTR_gpio))
+			schedule_work(&up->qos_work);
+		else
+			gpio_set_value(up->DTR_gpio,
+				       up->DTR_active != up->DTR_inverted);
+	}
 }
 
 static void serial_omap_break_ctl(struct uart_port *port, int break_state)
 {
-	struct uart_omap_port *up = (struct uart_omap_port *)port;
+	struct uart_omap_port *up = to_uart_omap_port(port);
 	unsigned long flags = 0;
 
 	dev_dbg(up->port.dev, "serial_omap_break_ctl+%d\n", up->port.line);
-	pm_runtime_get_sync(&up->pdev->dev);
+	pm_runtime_get_sync(up->dev);
 	spin_lock_irqsave(&up->port.lock, flags);
 	if (break_state == -1)
 		up->lcr |= UART_LCR_SBC;
@@ -523,12 +546,13 @@
 		up->lcr &= ~UART_LCR_SBC;
 	serial_out(up, UART_LCR, up->lcr);
 	spin_unlock_irqrestore(&up->port.lock, flags);
-	pm_runtime_put(&up->pdev->dev);
+	pm_runtime_mark_last_busy(up->dev);
+	pm_runtime_put_autosuspend(up->dev);
 }
 
 static int serial_omap_startup(struct uart_port *port)
 {
-	struct uart_omap_port *up = (struct uart_omap_port *)port;
+	struct uart_omap_port *up = to_uart_omap_port(port);
 	unsigned long flags = 0;
 	int retval;
 
@@ -542,7 +566,7 @@
 
 	dev_dbg(up->port.dev, "serial_omap_startup+%d\n", up->port.line);
 
-	pm_runtime_get_sync(&up->pdev->dev);
+	pm_runtime_get_sync(up->dev);
 	/*
 	 * Clear the FIFO buffers and disable them.
 	 * (they will be reenabled in set_termios())
@@ -573,20 +597,6 @@
 	spin_unlock_irqrestore(&up->port.lock, flags);
 
 	up->msr_saved_flags = 0;
-	if (up->use_dma) {
-		free_page((unsigned long)up->port.state->xmit.buf);
-		up->port.state->xmit.buf = dma_alloc_coherent(NULL,
-			UART_XMIT_SIZE,
-			(dma_addr_t *)&(up->uart_dma.tx_buf_dma_phys),
-			0);
-		init_timer(&(up->uart_dma.rx_timer));
-		up->uart_dma.rx_timer.function = serial_omap_rxdma_poll;
-		up->uart_dma.rx_timer.data = up->port.line;
-		/* Currently the buffer size is 4KB. Can increase it */
-		up->uart_dma.rx_buf = dma_alloc_coherent(NULL,
-			up->uart_dma.rx_buf_size,
-			(dma_addr_t *)&(up->uart_dma.rx_buf_dma_phys), 0);
-	}
 	/*
 	 * Finally, enable interrupts. Note: Modem status interrupts
 	 * are set via set_termios(), which will be occurring imminently
@@ -598,20 +608,20 @@
 	/* Enable module level wake up */
 	serial_out(up, UART_OMAP_WER, OMAP_UART_WER_MOD_WKUP);
 
-	pm_runtime_mark_last_busy(&up->pdev->dev);
-	pm_runtime_put_autosuspend(&up->pdev->dev);
+	pm_runtime_mark_last_busy(up->dev);
+	pm_runtime_put_autosuspend(up->dev);
 	up->port_activity = jiffies;
 	return 0;
 }
 
 static void serial_omap_shutdown(struct uart_port *port)
 {
-	struct uart_omap_port *up = (struct uart_omap_port *)port;
+	struct uart_omap_port *up = to_uart_omap_port(port);
 	unsigned long flags = 0;
 
 	dev_dbg(up->port.dev, "serial_omap_shutdown+%d\n", up->port.line);
 
-	pm_runtime_get_sync(&up->pdev->dev);
+	pm_runtime_get_sync(up->dev);
 	/*
 	 * Disable interrupts from this port
 	 */
@@ -634,19 +644,9 @@
 	 */
 	if (serial_in(up, UART_LSR) & UART_LSR_DR)
 		(void) serial_in(up, UART_RX);
-	if (up->use_dma) {
-		dma_free_coherent(up->port.dev,
-			UART_XMIT_SIZE,	up->port.state->xmit.buf,
-			up->uart_dma.tx_buf_dma_phys);
-		up->port.state->xmit.buf = NULL;
-		serial_omap_stop_rx(port);
-		dma_free_coherent(up->port.dev,
-			up->uart_dma.rx_buf_size, up->uart_dma.rx_buf,
-			up->uart_dma.rx_buf_dma_phys);
-		up->uart_dma.rx_buf = NULL;
-	}
 
-	pm_runtime_put(&up->pdev->dev);
+	pm_runtime_mark_last_busy(up->dev);
+	pm_runtime_put_autosuspend(up->dev);
 	free_irq(up->port.irq, up);
 }
 
@@ -667,19 +667,19 @@
 
 	/*
 	 * IXON Flag:
-	 * Enable XON/XOFF flow control on output.
-	 * Transmit XON1, XOFF1
+	 * Flow control for OMAP.TX
+	 * OMAP.RX should listen for XON/XOFF
 	 */
 	if (termios->c_iflag & IXON)
-		up->efr |= OMAP_UART_SW_TX;
+		up->efr |= OMAP_UART_SW_RX;
 
 	/*
 	 * IXOFF Flag:
-	 * Enable XON/XOFF flow control on input.
-	 * Receiver compares XON1, XOFF1.
+	 * Flow control for OMAP.RX
+	 * OMAP.TX should send XON/XOFF
 	 */
 	if (termios->c_iflag & IXOFF)
-		up->efr |= OMAP_UART_SW_RX;
+		up->efr |= OMAP_UART_SW_TX;
 
 	serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);
 	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
@@ -715,13 +715,16 @@
 						qos_work);
 
 	pm_qos_update_request(&up->pm_qos_request, up->latency);
+	if (gpio_is_valid(up->DTR_gpio))
+		gpio_set_value_cansleep(up->DTR_gpio,
+					up->DTR_active != up->DTR_inverted);
 }
 
 static void
 serial_omap_set_termios(struct uart_port *port, struct ktermios *termios,
 			struct ktermios *old)
 {
-	struct uart_omap_port *up = (struct uart_omap_port *)port;
+	struct uart_omap_port *up = to_uart_omap_port(port);
 	unsigned char cval = 0;
 	unsigned char efr = 0;
 	unsigned long flags = 0;
@@ -768,14 +771,12 @@
 
 	up->fcr = UART_FCR_R_TRIG_01 | UART_FCR_T_TRIG_01 |
 			UART_FCR_ENABLE_FIFO;
-	if (up->use_dma)
-		up->fcr |= UART_FCR_DMA_SELECT;
 
 	/*
 	 * Ok, we're now changing the port state. Do it with
 	 * interrupts disabled.
 	 */
-	pm_runtime_get_sync(&up->pdev->dev);
+	pm_runtime_get_sync(up->dev);
 	spin_lock_irqsave(&up->port.lock, flags);
 
 	/*
@@ -845,14 +846,13 @@
 
 	up->scr |= OMAP_UART_SCR_RX_TRIG_GRANU1_MASK;
 
-	if (up->use_dma) {
-		serial_out(up, UART_TI752_TLR, 0);
-		up->scr |= UART_FCR_TRIGGER_4;
-	} else {
-		/* Set receive FIFO threshold to 1 byte */
-		up->fcr &= ~OMAP_UART_FCR_RX_FIFO_TRIG_MASK;
-		up->fcr |= (0x1 << OMAP_UART_FCR_RX_FIFO_TRIG_SHIFT);
-	}
+	/* Set receive FIFO threshold to 16 characters and
+	 * transmit FIFO threshold to 16 spaces
+	 */
+	up->fcr &= ~OMAP_UART_FCR_RX_FIFO_TRIG_MASK;
+	up->fcr &= ~OMAP_UART_FCR_TX_FIFO_TRIG_MASK;
+	up->fcr |= UART_FCR6_R_TRIGGER_16 | UART_FCR6_T_TRIGGER_24 |
+		UART_FCR_ENABLE_FIFO;
 
 	serial_out(up, UART_FCR, up->fcr);
 	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
@@ -924,20 +924,30 @@
 	serial_omap_configure_xonxoff(up, termios);
 
 	spin_unlock_irqrestore(&up->port.lock, flags);
-	pm_runtime_put(&up->pdev->dev);
+	pm_runtime_mark_last_busy(up->dev);
+	pm_runtime_put_autosuspend(up->dev);
 	dev_dbg(up->port.dev, "serial_omap_set_termios+%d\n", up->port.line);
 }
 
+static int serial_omap_set_wake(struct uart_port *port, unsigned int state)
+{
+	struct uart_omap_port *up = to_uart_omap_port(port);
+
+	serial_omap_enable_wakeup(up, state);
+
+	return 0;
+}
+
 static void
 serial_omap_pm(struct uart_port *port, unsigned int state,
 	       unsigned int oldstate)
 {
-	struct uart_omap_port *up = (struct uart_omap_port *)port;
+	struct uart_omap_port *up = to_uart_omap_port(port);
 	unsigned char efr;
 
 	dev_dbg(up->port.dev, "serial_omap_pm+%d\n", up->port.line);
 
-	pm_runtime_get_sync(&up->pdev->dev);
+	pm_runtime_get_sync(up->dev);
 	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
 	efr = serial_in(up, UART_EFR);
 	serial_out(up, UART_EFR, efr | UART_EFR_ECB);
@@ -948,14 +958,15 @@
 	serial_out(up, UART_EFR, efr);
 	serial_out(up, UART_LCR, 0);
 
-	if (!device_may_wakeup(&up->pdev->dev)) {
+	if (!device_may_wakeup(up->dev)) {
 		if (!state)
-			pm_runtime_forbid(&up->pdev->dev);
+			pm_runtime_forbid(up->dev);
 		else
-			pm_runtime_allow(&up->pdev->dev);
+			pm_runtime_allow(up->dev);
 	}
 
-	pm_runtime_put(&up->pdev->dev);
+	pm_runtime_mark_last_busy(up->dev);
+	pm_runtime_put_autosuspend(up->dev);
 }
 
 static void serial_omap_release_port(struct uart_port *port)
@@ -971,7 +982,7 @@
 
 static void serial_omap_config_port(struct uart_port *port, int flags)
 {
-	struct uart_omap_port *up = (struct uart_omap_port *)port;
+	struct uart_omap_port *up = to_uart_omap_port(port);
 
 	dev_dbg(up->port.dev, "serial_omap_config_port+%d\n",
 							up->port.line);
@@ -989,7 +1000,7 @@
 static const char *
 serial_omap_type(struct uart_port *port)
 {
-	struct uart_omap_port *up = (struct uart_omap_port *)port;
+	struct uart_omap_port *up = to_uart_omap_port(port);
 
 	dev_dbg(up->port.dev, "serial_omap_type+%d\n", up->port.line);
 	return up->name;
@@ -1032,26 +1043,33 @@
 
 static void serial_omap_poll_put_char(struct uart_port *port, unsigned char ch)
 {
-	struct uart_omap_port *up = (struct uart_omap_port *)port;
+	struct uart_omap_port *up = to_uart_omap_port(port);
 
-	pm_runtime_get_sync(&up->pdev->dev);
+	pm_runtime_get_sync(up->dev);
 	wait_for_xmitr(up);
 	serial_out(up, UART_TX, ch);
-	pm_runtime_put(&up->pdev->dev);
+	pm_runtime_mark_last_busy(up->dev);
+	pm_runtime_put_autosuspend(up->dev);
 }
 
 static int serial_omap_poll_get_char(struct uart_port *port)
 {
-	struct uart_omap_port *up = (struct uart_omap_port *)port;
+	struct uart_omap_port *up = to_uart_omap_port(port);
 	unsigned int status;
 
-	pm_runtime_get_sync(&up->pdev->dev);
+	pm_runtime_get_sync(up->dev);
 	status = serial_in(up, UART_LSR);
-	if (!(status & UART_LSR_DR))
-		return NO_POLL_CHAR;
+	if (!(status & UART_LSR_DR)) {
+		status = NO_POLL_CHAR;
+		goto out;
+	}
 
 	status = serial_in(up, UART_RX);
-	pm_runtime_put(&up->pdev->dev);
+
+out:
+	pm_runtime_mark_last_busy(up->dev);
+	pm_runtime_put_autosuspend(up->dev);
+
 	return status;
 }
 
@@ -1065,7 +1083,7 @@
 
 static void serial_omap_console_putchar(struct uart_port *port, int ch)
 {
-	struct uart_omap_port *up = (struct uart_omap_port *)port;
+	struct uart_omap_port *up = to_uart_omap_port(port);
 
 	wait_for_xmitr(up);
 	serial_out(up, UART_TX, ch);
@@ -1080,7 +1098,7 @@
 	unsigned int ier;
 	int locked = 1;
 
-	pm_runtime_get_sync(&up->pdev->dev);
+	pm_runtime_get_sync(up->dev);
 
 	local_irq_save(flags);
 	if (up->port.sysrq)
@@ -1114,8 +1132,8 @@
 	if (up->msr_saved_flags)
 		check_modem_status(up);
 
-	pm_runtime_mark_last_busy(&up->pdev->dev);
-	pm_runtime_put_autosuspend(&up->pdev->dev);
+	pm_runtime_mark_last_busy(up->dev);
+	pm_runtime_put_autosuspend(up->dev);
 	if (locked)
 		spin_unlock(&up->port.lock);
 	local_irq_restore(flags);
@@ -1179,6 +1197,7 @@
 	.shutdown	= serial_omap_shutdown,
 	.set_termios	= serial_omap_set_termios,
 	.pm		= serial_omap_pm,
+	.set_wake	= serial_omap_set_wake,
 	.type		= serial_omap_type,
 	.release_port	= serial_omap_release_port,
 	.request_port	= serial_omap_request_port,
@@ -1221,150 +1240,7 @@
 }
 #endif
 
-static void serial_omap_rxdma_poll(unsigned long uart_no)
-{
-	struct uart_omap_port *up = ui[uart_no];
-	unsigned int curr_dma_pos, curr_transmitted_size;
-	int ret = 0;
-
-	curr_dma_pos = omap_get_dma_dst_pos(up->uart_dma.rx_dma_channel);
-	if ((curr_dma_pos == up->uart_dma.prev_rx_dma_pos) ||
-			     (curr_dma_pos == 0)) {
-		if (jiffies_to_msecs(jiffies - up->port_activity) <
-						up->uart_dma.rx_timeout) {
-			mod_timer(&up->uart_dma.rx_timer, jiffies +
-				usecs_to_jiffies(up->uart_dma.rx_poll_rate));
-		} else {
-			serial_omap_stop_rxdma(up);
-			up->ier |= (UART_IER_RDI | UART_IER_RLSI);
-			serial_out(up, UART_IER, up->ier);
-		}
-		return;
-	}
-
-	curr_transmitted_size = curr_dma_pos -
-					up->uart_dma.prev_rx_dma_pos;
-	up->port.icount.rx += curr_transmitted_size;
-	tty_insert_flip_string(up->port.state->port.tty,
-			up->uart_dma.rx_buf +
-			(up->uart_dma.prev_rx_dma_pos -
-			up->uart_dma.rx_buf_dma_phys),
-			curr_transmitted_size);
-	tty_flip_buffer_push(up->port.state->port.tty);
-	up->uart_dma.prev_rx_dma_pos = curr_dma_pos;
-	if (up->uart_dma.rx_buf_size +
-			up->uart_dma.rx_buf_dma_phys == curr_dma_pos) {
-		ret = serial_omap_start_rxdma(up);
-		if (ret < 0) {
-			serial_omap_stop_rxdma(up);
-			up->ier |= (UART_IER_RDI | UART_IER_RLSI);
-			serial_out(up, UART_IER, up->ier);
-		}
-	} else  {
-		mod_timer(&up->uart_dma.rx_timer, jiffies +
-			usecs_to_jiffies(up->uart_dma.rx_poll_rate));
-	}
-	up->port_activity = jiffies;
-}
-
-static void uart_rx_dma_callback(int lch, u16 ch_status, void *data)
-{
-	return;
-}
-
-static int serial_omap_start_rxdma(struct uart_omap_port *up)
-{
-	int ret = 0;
-
-	if (up->uart_dma.rx_dma_channel == -1) {
-		pm_runtime_get_sync(&up->pdev->dev);
-		ret = omap_request_dma(up->uart_dma.uart_dma_rx,
-				"UART Rx DMA",
-				(void *)uart_rx_dma_callback, up,
-				&(up->uart_dma.rx_dma_channel));
-		if (ret < 0)
-			return ret;
-
-		omap_set_dma_src_params(up->uart_dma.rx_dma_channel, 0,
-				OMAP_DMA_AMODE_CONSTANT,
-				up->uart_dma.uart_base, 0, 0);
-		omap_set_dma_dest_params(up->uart_dma.rx_dma_channel, 0,
-				OMAP_DMA_AMODE_POST_INC,
-				up->uart_dma.rx_buf_dma_phys, 0, 0);
-		omap_set_dma_transfer_params(up->uart_dma.rx_dma_channel,
-				OMAP_DMA_DATA_TYPE_S8,
-				up->uart_dma.rx_buf_size, 1,
-				OMAP_DMA_SYNC_ELEMENT,
-				up->uart_dma.uart_dma_rx, 0);
-	}
-	up->uart_dma.prev_rx_dma_pos = up->uart_dma.rx_buf_dma_phys;
-	/* FIXME: Cache maintenance needed here? */
-	omap_start_dma(up->uart_dma.rx_dma_channel);
-	mod_timer(&up->uart_dma.rx_timer, jiffies +
-				usecs_to_jiffies(up->uart_dma.rx_poll_rate));
-	up->uart_dma.rx_dma_used = true;
-	return ret;
-}
-
-static void serial_omap_continue_tx(struct uart_omap_port *up)
-{
-	struct circ_buf *xmit = &up->port.state->xmit;
-	unsigned int start = up->uart_dma.tx_buf_dma_phys
-			+ (xmit->tail & (UART_XMIT_SIZE - 1));
-
-	if (uart_circ_empty(xmit))
-		return;
-
-	up->uart_dma.tx_buf_size = uart_circ_chars_pending(xmit);
-	/*
-	 * It is a circular buffer. See if the buffer has wounded back.
-	 * If yes it will have to be transferred in two separate dma
-	 * transfers
-	 */
-	if (start + up->uart_dma.tx_buf_size >=
-			up->uart_dma.tx_buf_dma_phys + UART_XMIT_SIZE)
-		up->uart_dma.tx_buf_size =
-			(up->uart_dma.tx_buf_dma_phys + UART_XMIT_SIZE) - start;
-	omap_set_dma_dest_params(up->uart_dma.tx_dma_channel, 0,
-				OMAP_DMA_AMODE_CONSTANT,
-				up->uart_dma.uart_base, 0, 0);
-	omap_set_dma_src_params(up->uart_dma.tx_dma_channel, 0,
-				OMAP_DMA_AMODE_POST_INC, start, 0, 0);
-	omap_set_dma_transfer_params(up->uart_dma.tx_dma_channel,
-				OMAP_DMA_DATA_TYPE_S8,
-				up->uart_dma.tx_buf_size, 1,
-				OMAP_DMA_SYNC_ELEMENT,
-				up->uart_dma.uart_dma_tx, 0);
-	/* FIXME: Cache maintenance needed here? */
-	omap_start_dma(up->uart_dma.tx_dma_channel);
-}
-
-static void uart_tx_dma_callback(int lch, u16 ch_status, void *data)
-{
-	struct uart_omap_port *up = (struct uart_omap_port *)data;
-	struct circ_buf *xmit = &up->port.state->xmit;
-
-	xmit->tail = (xmit->tail + up->uart_dma.tx_buf_size) & \
-			(UART_XMIT_SIZE - 1);
-	up->port.icount.tx += up->uart_dma.tx_buf_size;
-
-	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
-		uart_write_wakeup(&up->port);
-
-	if (uart_circ_empty(xmit)) {
-		spin_lock(&(up->uart_dma.tx_lock));
-		serial_omap_stop_tx(&up->port);
-		up->uart_dma.tx_dma_used = false;
-		spin_unlock(&(up->uart_dma.tx_lock));
-	} else {
-		omap_stop_dma(up->uart_dma.tx_dma_channel);
-		serial_omap_continue_tx(up);
-	}
-	up->port_activity = jiffies;
-	return;
-}
-
-static void omap_serial_fill_features_erratas(struct uart_omap_port *up)
+static void __devinit omap_serial_fill_features_erratas(struct uart_omap_port *up)
 {
 	u32 mvr, scheme;
 	u16 revision, major, minor;
@@ -1389,7 +1265,7 @@
 		minor = (mvr & OMAP_UART_MVR_MIN_MASK);
 		break;
 	default:
-		dev_warn(&up->pdev->dev,
+		dev_warn(up->dev,
 			"Unknown %s revision, defaulting to highest\n",
 			up->name);
 		/* highest possible revision */
@@ -1417,7 +1293,7 @@
 	}
 }
 
-static struct omap_uart_port_info *of_get_uart_port_info(struct device *dev)
+static __devinit struct omap_uart_port_info *of_get_uart_port_info(struct device *dev)
 {
 	struct omap_uart_port_info *omap_up_info;
 
@@ -1430,12 +1306,12 @@
 	return omap_up_info;
 }
 
-static int serial_omap_probe(struct platform_device *pdev)
+static int __devinit serial_omap_probe(struct platform_device *pdev)
 {
 	struct uart_omap_port	*up;
-	struct resource		*mem, *irq, *dma_tx, *dma_rx;
+	struct resource		*mem, *irq;
 	struct omap_uart_port_info *omap_up_info = pdev->dev.platform_data;
-	int ret = -ENOSPC;
+	int ret;
 
 	if (pdev->dev.of_node)
 		omap_up_info = of_get_uart_port_info(&pdev->dev);
@@ -1458,19 +1334,30 @@
 		return -EBUSY;
 	}
 
-	dma_rx = platform_get_resource_byname(pdev, IORESOURCE_DMA, "rx");
-	if (!dma_rx)
-		return -ENXIO;
-
-	dma_tx = platform_get_resource_byname(pdev, IORESOURCE_DMA, "tx");
-	if (!dma_tx)
-		return -ENXIO;
+	if (gpio_is_valid(omap_up_info->DTR_gpio) &&
+	    omap_up_info->DTR_present) {
+		ret = gpio_request(omap_up_info->DTR_gpio, "omap-serial");
+		if (ret < 0)
+			return ret;
+		ret = gpio_direction_output(omap_up_info->DTR_gpio,
+					    omap_up_info->DTR_inverted);
+		if (ret < 0)
+			return ret;
+	}
 
 	up = devm_kzalloc(&pdev->dev, sizeof(*up), GFP_KERNEL);
 	if (!up)
 		return -ENOMEM;
 
-	up->pdev = pdev;
+	if (gpio_is_valid(omap_up_info->DTR_gpio) &&
+	    omap_up_info->DTR_present) {
+		up->DTR_gpio = omap_up_info->DTR_gpio;
+		up->DTR_inverted = omap_up_info->DTR_inverted;
+	} else
+		up->DTR_gpio = -EINVAL;
+	up->DTR_active = 0;
+
+	up->dev = &pdev->dev;
 	up->port.dev = &pdev->dev;
 	up->port.type = PORT_OMAP;
 	up->port.iotype = UPIO_MEM;
@@ -1492,6 +1379,13 @@
 		goto err_port_line;
 	}
 
+	up->pins = devm_pinctrl_get_select_default(&pdev->dev);
+	if (IS_ERR(up->pins)) {
+		dev_warn(&pdev->dev, "did not get pins for uart%i error: %li\n",
+			 up->port.line, PTR_ERR(up->pins));
+		up->pins = NULL;
+	}
+
 	sprintf(up->name, "OMAP UART%d", up->port.line);
 	up->port.mapbase = mem->start;
 	up->port.membase = devm_ioremap(&pdev->dev, mem->start,
@@ -1509,20 +1403,6 @@
 		dev_warn(&pdev->dev, "No clock speed specified: using default:"
 						"%d\n", DEFAULT_CLK_SPEED);
 	}
-	up->uart_dma.uart_base = mem->start;
-
-	if (omap_up_info->dma_enabled) {
-		up->uart_dma.uart_dma_tx = dma_tx->start;
-		up->uart_dma.uart_dma_rx = dma_rx->start;
-		up->use_dma = 1;
-		up->uart_dma.rx_buf_size = omap_up_info->dma_rx_buf_size;
-		up->uart_dma.rx_timeout = omap_up_info->dma_rx_timeout;
-		up->uart_dma.rx_poll_rate = omap_up_info->dma_rx_poll_rate;
-		spin_lock_init(&(up->uart_dma.tx_lock));
-		spin_lock_init(&(up->uart_dma.rx_lock));
-		up->uart_dma.tx_dma_channel = OMAP_UART_DMA_CH_FREE;
-		up->uart_dma.rx_dma_channel = OMAP_UART_DMA_CH_FREE;
-	}
 
 	up->latency = PM_QOS_CPU_DMA_LAT_DEFAULT_VALUE;
 	up->calc_latency = PM_QOS_CPU_DMA_LAT_DEFAULT_VALUE;
@@ -1531,12 +1411,13 @@
 	serial_omap_uart_wq = create_singlethread_workqueue(up->name);
 	INIT_WORK(&up->qos_work, serial_omap_uart_qos_work);
 
+	platform_set_drvdata(pdev, up);
+	pm_runtime_enable(&pdev->dev);
 	pm_runtime_use_autosuspend(&pdev->dev);
 	pm_runtime_set_autosuspend_delay(&pdev->dev,
 			omap_up_info->autosuspend_timeout);
 
 	pm_runtime_irq_safe(&pdev->dev);
-	pm_runtime_enable(&pdev->dev);
 	pm_runtime_get_sync(&pdev->dev);
 
 	omap_serial_fill_features_erratas(up);
@@ -1548,8 +1429,8 @@
 	if (ret != 0)
 		goto err_add_port;
 
-	pm_runtime_put(&pdev->dev);
-	platform_set_drvdata(pdev, up);
+	pm_runtime_mark_last_busy(up->dev);
+	pm_runtime_put_autosuspend(up->dev);
 	return 0;
 
 err_add_port:
@@ -1562,17 +1443,15 @@
 	return ret;
 }
 
-static int serial_omap_remove(struct platform_device *dev)
+static int __devexit serial_omap_remove(struct platform_device *dev)
 {
 	struct uart_omap_port *up = platform_get_drvdata(dev);
 
-	if (up) {
-		pm_runtime_disable(&up->pdev->dev);
-		uart_remove_one_port(&serial_omap_reg, &up->port);
-		pm_qos_remove_request(&up->pm_qos_request);
-	}
+	pm_runtime_put_sync(up->dev);
+	pm_runtime_disable(up->dev);
+	uart_remove_one_port(&serial_omap_reg, &up->port);
+	pm_qos_remove_request(&up->pm_qos_request);
 
-	platform_set_drvdata(dev, NULL);
 	return 0;
 }
 
@@ -1602,7 +1481,7 @@
 		timeout--;
 		if (!timeout) {
 			/* Should *never* happen. we warn and carry on */
-			dev_crit(&up->pdev->dev, "Errata i202: timedout %x\n",
+			dev_crit(up->dev, "Errata i202: timedout %x\n",
 						serial_in(up, UART_LSR));
 			break;
 		}
@@ -1648,29 +1527,23 @@
 	if (!up)
 		return -EINVAL;
 
-	if (!pdata || !pdata->enable_wakeup)
+	if (!pdata)
 		return 0;
 
-	if (pdata->get_context_loss_count)
-		up->context_loss_cnt = pdata->get_context_loss_count(dev);
+	up->context_loss_cnt = serial_omap_get_context_loss_count(up);
 
 	if (device_may_wakeup(dev)) {
 		if (!up->wakeups_enabled) {
-			pdata->enable_wakeup(up->pdev, true);
+			serial_omap_enable_wakeup(up, true);
 			up->wakeups_enabled = true;
 		}
 	} else {
 		if (up->wakeups_enabled) {
-			pdata->enable_wakeup(up->pdev, false);
+			serial_omap_enable_wakeup(up, false);
 			up->wakeups_enabled = false;
 		}
 	}
 
-	/* Errata i291 */
-	if (up->use_dma && pdata->set_forceidle &&
-			(up->errata & UART_ERRATA_i291_DMA_FORCEIDLE))
-		pdata->set_forceidle(up->pdev);
-
 	up->latency = PM_QOS_CPU_DMA_LAT_DEFAULT_VALUE;
 	schedule_work(&up->qos_work);
 
@@ -1683,17 +1556,10 @@
 	struct omap_uart_port_info *pdata = dev->platform_data;
 
 	if (up && pdata) {
-		if (pdata->get_context_loss_count) {
-			u32 loss_cnt = pdata->get_context_loss_count(dev);
+			u32 loss_cnt = serial_omap_get_context_loss_count(up);
 
 			if (up->context_loss_cnt != loss_cnt)
 				serial_omap_restore_context(up);
-		}
-
-		/* Errata i291 */
-		if (up->use_dma && pdata->set_noidle &&
-				(up->errata & UART_ERRATA_i291_DMA_FORCEIDLE))
-			pdata->set_noidle(up->pdev);
 
 		up->latency = up->calc_latency;
 		schedule_work(&up->qos_work);
@@ -1721,7 +1587,7 @@
 
 static struct platform_driver serial_omap_driver = {
 	.probe          = serial_omap_probe,
-	.remove         = serial_omap_remove,
+	.remove         = __devexit_p(serial_omap_remove),
 	.driver		= {
 		.name	= DRIVER_NAME,
 		.pm	= &serial_omap_dev_pm_ops,
diff --git a/drivers/tty/serial/pch_uart.c b/drivers/tty/serial/pch_uart.c
index 558ce85..4cd6c23 100644
--- a/drivers/tty/serial/pch_uart.c
+++ b/drivers/tty/serial/pch_uart.c
@@ -979,6 +979,10 @@
 	priv->tx_dma_use = 1;
 
 	priv->sg_tx_p = kzalloc(sizeof(struct scatterlist)*num, GFP_ATOMIC);
+	if (!priv->sg_tx_p) {
+		dev_err(priv->port.dev, "%s:kzalloc Failed\n", __func__);
+		return 0;
+	}
 
 	sg_init_table(priv->sg_tx_p, num); /* Initialize SG table */
 	sg = priv->sg_tx_p;
diff --git a/drivers/tty/serial/pxa.c b/drivers/tty/serial/pxa.c
index 5847a4b..9033fc6 100644
--- a/drivers/tty/serial/pxa.c
+++ b/drivers/tty/serial/pxa.c
@@ -670,9 +670,19 @@
 {
 	struct uart_pxa_port *up = serial_pxa_ports[co->index];
 	unsigned int ier;
+	unsigned long flags;
+	int locked = 1;
 
 	clk_prepare_enable(up->clk);
 
+	local_irq_save(flags);
+	if (up->port.sysrq)
+		locked = 0;
+	else if (oops_in_progress)
+		locked = spin_trylock(&up->port.lock);
+	else
+		spin_lock(&up->port.lock);
+
 	/*
 	 *	First save the IER then disable the interrupts
 	 */
@@ -688,6 +698,10 @@
 	wait_for_xmitr(up);
 	serial_out(up, UART_IER, ier);
 
+	if (locked)
+		spin_unlock(&up->port.lock);
+	local_irq_restore(flags);
+
 	clk_disable_unprepare(up->clk);
 }
 
diff --git a/drivers/tty/serial/samsung.c b/drivers/tty/serial/samsung.c
index 02d07bf..bdaa06f 100644
--- a/drivers/tty/serial/samsung.c
+++ b/drivers/tty/serial/samsung.c
@@ -82,7 +82,7 @@
 
 static int s3c24xx_serial_txempty_nofifo(struct uart_port *port)
 {
-	return (rd_regl(port, S3C2410_UTRSTAT) & S3C2410_UTRSTAT_TXE);
+	return rd_regl(port, S3C2410_UTRSTAT) & S3C2410_UTRSTAT_TXE;
 }
 
 /*
@@ -268,7 +268,7 @@
 				dbg("break!\n");
 				port->icount.brk++;
 				if (uart_handle_break(port))
-				    goto ignore_char;
+					goto ignore_char;
 			}
 
 			if (uerstat & S3C2410_UERSTAT_FRAME)
@@ -459,7 +459,7 @@
 			  s3c24xx_serial_portname(port), ourport);
 
 	if (ret != 0) {
-		printk(KERN_ERR "cannot get irq %d\n", ourport->rx_irq);
+		dev_err(port->dev, "cannot get irq %d\n", ourport->rx_irq);
 		return ret;
 	}
 
@@ -473,7 +473,7 @@
 			  s3c24xx_serial_portname(port), ourport);
 
 	if (ret) {
-		printk(KERN_ERR "cannot get irq %d\n", ourport->tx_irq);
+		dev_err(port->dev, "cannot get irq %d\n", ourport->tx_irq);
 		goto err;
 	}
 
@@ -502,7 +502,7 @@
 	ret = request_irq(port->irq, s3c64xx_serial_handle_irq, IRQF_SHARED,
 			  s3c24xx_serial_portname(port), ourport);
 	if (ret) {
-		printk(KERN_ERR "cannot get irq %d\n", port->irq);
+		dev_err(port->dev, "cannot get irq %d\n", port->irq);
 		return ret;
 	}
 
@@ -529,7 +529,7 @@
 
 	switch (level) {
 	case 3:
-		if (!IS_ERR(ourport->baudclk) && ourport->baudclk != NULL)
+		if (!IS_ERR(ourport->baudclk))
 			clk_disable(ourport->baudclk);
 
 		clk_disable(ourport->clk);
@@ -538,12 +538,12 @@
 	case 0:
 		clk_enable(ourport->clk);
 
-		if (!IS_ERR(ourport->baudclk) && ourport->baudclk != NULL)
+		if (!IS_ERR(ourport->baudclk))
 			clk_enable(ourport->baudclk);
 
 		break;
 	default:
-		printk(KERN_ERR "s3c24xx_serial: unknown pm %d\n", level);
+		dev_err(port->dev, "s3c24xx_serial: unknown pm %d\n", level);
 	}
 }
 
@@ -604,7 +604,6 @@
 	char clkname[MAX_CLK_NAME_LENGTH];
 	int calc_deviation, deviation = (1 << 30) - 1;
 
-	*best_clk = NULL;
 	clk_sel = (ourport->cfg->clk_sel) ? ourport->cfg->clk_sel :
 			ourport->info->def_clk_sel;
 	for (cnt = 0; cnt < info->num_clks; cnt++) {
@@ -613,7 +612,7 @@
 
 		sprintf(clkname, "clk_uart_baud%d", cnt);
 		clk = clk_get(ourport->port.dev, clkname);
-		if (IS_ERR_OR_NULL(clk))
+		if (IS_ERR(clk))
 			continue;
 
 		rate = clk_get_rate(clk);
@@ -684,7 +683,7 @@
 {
 	struct s3c2410_uartcfg *cfg = s3c24xx_port_to_cfg(port);
 	struct s3c24xx_uart_port *ourport = to_ourport(port);
-	struct clk *clk = NULL;
+	struct clk *clk = ERR_PTR(-EINVAL);
 	unsigned long flags;
 	unsigned int baud, quot, clk_sel = 0;
 	unsigned int ulcon;
@@ -705,7 +704,7 @@
 	quot = s3c24xx_serial_getclk(ourport, baud, &clk, &clk_sel);
 	if (baud == 38400 && (port->flags & UPF_SPD_MASK) == UPF_SPD_CUST)
 		quot = port->custom_divisor;
-	if (!clk)
+	if (IS_ERR(clk))
 		return;
 
 	/* check to see if we need  to change clock source */
@@ -713,9 +712,9 @@
 	if (ourport->baudclk != clk) {
 		s3c24xx_serial_setsource(port, clk_sel);
 
-		if (ourport->baudclk != NULL && !IS_ERR(ourport->baudclk)) {
+		if (!IS_ERR(ourport->baudclk)) {
 			clk_disable(ourport->baudclk);
-			ourport->baudclk  = NULL;
+			ourport->baudclk = ERR_PTR(-EINVAL);
 		}
 
 		clk_enable(clk);
@@ -1036,10 +1035,10 @@
 		if (tty == NULL)
 			goto exit;
 
-		termios = tty->termios;
+		termios = &tty->termios;
 
 		if (termios == NULL) {
-			printk(KERN_WARNING "%s: no termios?\n", __func__);
+			dev_warn(uport->dev, "%s: no termios?\n", __func__);
 			goto exit;
 		}
 
@@ -1114,7 +1113,7 @@
 
 	res = platform_get_resource(platdev, IORESOURCE_MEM, 0);
 	if (res == NULL) {
-		printk(KERN_ERR "failed to find memory resource for uart\n");
+		dev_err(port->dev, "failed to find memory resource for uart\n");
 		return -EINVAL;
 	}
 
@@ -1130,7 +1129,7 @@
 		ourport->rx_irq = ret;
 		ourport->tx_irq = ret + 1;
 	}
-	
+
 	ret = platform_get_irq(platdev, 1);
 	if (ret > 0)
 		ourport->tx_irq = ret;
@@ -1160,7 +1159,11 @@
 	struct uart_port *port = s3c24xx_dev_to_port(dev);
 	struct s3c24xx_uart_port *ourport = to_ourport(port);
 
-	return snprintf(buf, PAGE_SIZE, "* %s\n", ourport->baudclk->name);
+	if (IS_ERR(ourport->baudclk))
+		return -EINVAL;
+
+	return snprintf(buf, PAGE_SIZE, "* %s\n",
+			ourport->baudclk->name ?: "(null)");
 }
 
 static DEVICE_ATTR(clock_source, S_IRUGO, s3c24xx_serial_show_clksrc, NULL);
@@ -1200,6 +1203,7 @@
 		return -ENODEV;
 	}
 
+	ourport->baudclk = ERR_PTR(-EINVAL);
 	ourport->info = ourport->drv_data->info;
 	ourport->cfg = (pdev->dev.platform_data) ?
 			(struct s3c2410_uartcfg *)pdev->dev.platform_data :
@@ -1387,7 +1391,7 @@
 		sprintf(clk_name, "clk_uart_baud%d", clk_sel);
 
 		clk = clk_get(port->dev, clk_name);
-		if (!IS_ERR(clk) && clk != NULL)
+		if (!IS_ERR(clk))
 			rate = clk_get_rate(clk);
 		else
 			rate = 1;
@@ -1679,7 +1683,7 @@
 
 	ret = uart_register_driver(&s3c24xx_uart_drv);
 	if (ret < 0) {
-		printk(KERN_ERR "failed to register UART driver\n");
+		pr_err("Failed to register Samsung UART driver\n");
 		return -1;
 	}
 
diff --git a/drivers/tty/serial/sc26xx.c b/drivers/tty/serial/sc26xx.c
index e0b4b0a..9d66424 100644
--- a/drivers/tty/serial/sc26xx.c
+++ b/drivers/tty/serial/sc26xx.c
@@ -20,6 +20,10 @@
 #include <linux/init.h>
 #include <linux/platform_device.h>
 #include <linux/irq.h>
+#include <linux/io.h>
+
+#warning "Please try migrate to use new driver SCCNXP and report the status" \
+	 "in the linux-serial mailing list."
 
 #if defined(CONFIG_MAGIC_SYSRQ)
 #define SUPPORT_SYSRQ
diff --git a/drivers/tty/serial/sccnxp.c b/drivers/tty/serial/sccnxp.c
new file mode 100644
index 0000000..05d767c
--- /dev/null
+++ b/drivers/tty/serial/sccnxp.c
@@ -0,0 +1,985 @@
+/*
+ *  NXP (Philips) SCC+++(SCN+++) serial driver
+ *
+ *  Copyright (C) 2012 Alexander Shiyan <shc_work@mail.ru>
+ *
+ *  Based on sc26xx.c, by Thomas Bogendörfer (tsbogend@alpha.franken.de)
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#if defined(CONFIG_SERIAL_SCCNXP_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+#define SUPPORT_SYSRQ
+#endif
+
+#include <linux/module.h>
+#include <linux/device.h>
+#include <linux/console.h>
+#include <linux/serial_core.h>
+#include <linux/serial.h>
+#include <linux/io.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/platform_device.h>
+#include <linux/platform_data/sccnxp.h>
+
+#define SCCNXP_NAME			"uart-sccnxp"
+#define SCCNXP_MAJOR			204
+#define SCCNXP_MINOR			205
+
+#define SCCNXP_MR_REG			(0x00)
+#	define MR0_BAUD_NORMAL		(0 << 0)
+#	define MR0_BAUD_EXT1		(1 << 0)
+#	define MR0_BAUD_EXT2		(5 << 0)
+#	define MR0_FIFO			(1 << 3)
+#	define MR0_TXLVL		(1 << 4)
+#	define MR1_BITS_5		(0 << 0)
+#	define MR1_BITS_6		(1 << 0)
+#	define MR1_BITS_7		(2 << 0)
+#	define MR1_BITS_8		(3 << 0)
+#	define MR1_PAR_EVN		(0 << 2)
+#	define MR1_PAR_ODD		(1 << 2)
+#	define MR1_PAR_NO		(4 << 2)
+#	define MR2_STOP1		(7 << 0)
+#	define MR2_STOP2		(0xf << 0)
+#define SCCNXP_SR_REG			(0x01)
+#define SCCNXP_CSR_REG			SCCNXP_SR_REG
+#	define SR_RXRDY			(1 << 0)
+#	define SR_FULL			(1 << 1)
+#	define SR_TXRDY			(1 << 2)
+#	define SR_TXEMT			(1 << 3)
+#	define SR_OVR			(1 << 4)
+#	define SR_PE			(1 << 5)
+#	define SR_FE			(1 << 6)
+#	define SR_BRK			(1 << 7)
+#define SCCNXP_CR_REG			(0x02)
+#	define CR_RX_ENABLE		(1 << 0)
+#	define CR_RX_DISABLE		(1 << 1)
+#	define CR_TX_ENABLE		(1 << 2)
+#	define CR_TX_DISABLE		(1 << 3)
+#	define CR_CMD_MRPTR1		(0x01 << 4)
+#	define CR_CMD_RX_RESET		(0x02 << 4)
+#	define CR_CMD_TX_RESET		(0x03 << 4)
+#	define CR_CMD_STATUS_RESET	(0x04 << 4)
+#	define CR_CMD_BREAK_RESET	(0x05 << 4)
+#	define CR_CMD_START_BREAK	(0x06 << 4)
+#	define CR_CMD_STOP_BREAK	(0x07 << 4)
+#	define CR_CMD_MRPTR0		(0x0b << 4)
+#define SCCNXP_RHR_REG			(0x03)
+#define SCCNXP_THR_REG			SCCNXP_RHR_REG
+#define SCCNXP_IPCR_REG			(0x04)
+#define SCCNXP_ACR_REG			SCCNXP_IPCR_REG
+#	define ACR_BAUD0		(0 << 7)
+#	define ACR_BAUD1		(1 << 7)
+#	define ACR_TIMER_MODE		(6 << 4)
+#define SCCNXP_ISR_REG			(0x05)
+#define SCCNXP_IMR_REG			SCCNXP_ISR_REG
+#	define IMR_TXRDY		(1 << 0)
+#	define IMR_RXRDY		(1 << 1)
+#	define ISR_TXRDY(x)		(1 << ((x * 4) + 0))
+#	define ISR_RXRDY(x)		(1 << ((x * 4) + 1))
+#define SCCNXP_IPR_REG			(0x0d)
+#define SCCNXP_OPCR_REG			SCCNXP_IPR_REG
+#define SCCNXP_SOP_REG			(0x0e)
+#define SCCNXP_ROP_REG			(0x0f)
+
+/* Route helpers */
+#define MCTRL_MASK(sig)			(0xf << (sig))
+#define MCTRL_IBIT(cfg, sig)		((((cfg) >> (sig)) & 0xf) - LINE_IP0)
+#define MCTRL_OBIT(cfg, sig)		((((cfg) >> (sig)) & 0xf) - LINE_OP0)
+
+/* Supported chip types */
+enum {
+	SCCNXP_TYPE_SC2681	= 2681,
+	SCCNXP_TYPE_SC2691	= 2691,
+	SCCNXP_TYPE_SC2692	= 2692,
+	SCCNXP_TYPE_SC2891	= 2891,
+	SCCNXP_TYPE_SC2892	= 2892,
+	SCCNXP_TYPE_SC28202	= 28202,
+	SCCNXP_TYPE_SC68681	= 68681,
+	SCCNXP_TYPE_SC68692	= 68692,
+};
+
+struct sccnxp_port {
+	struct uart_driver	uart;
+	struct uart_port	port[SCCNXP_MAX_UARTS];
+
+	const char		*name;
+	int			irq;
+
+	u8			imr;
+	u8			addr_mask;
+	int			freq_std;
+
+	int			flags;
+#define SCCNXP_HAVE_IO		0x00000001
+#define SCCNXP_HAVE_MR0		0x00000002
+
+#ifdef CONFIG_SERIAL_SCCNXP_CONSOLE
+	struct console		console;
+#endif
+
+	struct mutex		sccnxp_mutex;
+
+	struct sccnxp_pdata	pdata;
+};
+
+static inline u8 sccnxp_raw_read(void __iomem *base, u8 reg, u8 shift)
+{
+	return readb(base + (reg << shift));
+}
+
+static inline void sccnxp_raw_write(void __iomem *base, u8 reg, u8 shift, u8 v)
+{
+	writeb(v, base + (reg << shift));
+}
+
+static inline u8 sccnxp_read(struct uart_port *port, u8 reg)
+{
+	struct sccnxp_port *s = dev_get_drvdata(port->dev);
+
+	return sccnxp_raw_read(port->membase, reg & s->addr_mask,
+			       port->regshift);
+}
+
+static inline void sccnxp_write(struct uart_port *port, u8 reg, u8 v)
+{
+	struct sccnxp_port *s = dev_get_drvdata(port->dev);
+
+	sccnxp_raw_write(port->membase, reg & s->addr_mask, port->regshift, v);
+}
+
+static inline u8 sccnxp_port_read(struct uart_port *port, u8 reg)
+{
+	return sccnxp_read(port, (port->line << 3) + reg);
+}
+
+static inline void sccnxp_port_write(struct uart_port *port, u8 reg, u8 v)
+{
+	sccnxp_write(port, (port->line << 3) + reg, v);
+}
+
+static int sccnxp_update_best_err(int a, int b, int *besterr)
+{
+	int err = abs(a - b);
+
+	if ((*besterr < 0) || (*besterr > err)) {
+		*besterr = err;
+		return 0;
+	}
+
+	return 1;
+}
+
+struct baud_table {
+	u8	csr;
+	u8	acr;
+	u8	mr0;
+	int	baud;
+};
+
+const struct baud_table baud_std[] = {
+	{ 0,	ACR_BAUD0,	MR0_BAUD_NORMAL,	50, },
+	{ 0,	ACR_BAUD1,	MR0_BAUD_NORMAL,	75, },
+	{ 1,	ACR_BAUD0,	MR0_BAUD_NORMAL,	110, },
+	{ 2,	ACR_BAUD0,	MR0_BAUD_NORMAL,	134, },
+	{ 3,	ACR_BAUD1,	MR0_BAUD_NORMAL,	150, },
+	{ 3,	ACR_BAUD0,	MR0_BAUD_NORMAL,	200, },
+	{ 4,	ACR_BAUD0,	MR0_BAUD_NORMAL,	300, },
+	{ 0,	ACR_BAUD1,	MR0_BAUD_EXT1,		450, },
+	{ 1,	ACR_BAUD0,	MR0_BAUD_EXT2,		880, },
+	{ 3,	ACR_BAUD1,	MR0_BAUD_EXT1,		900, },
+	{ 5,	ACR_BAUD0,	MR0_BAUD_NORMAL,	600, },
+	{ 7,	ACR_BAUD0,	MR0_BAUD_NORMAL,	1050, },
+	{ 2,	ACR_BAUD0,	MR0_BAUD_EXT2,		1076, },
+	{ 6,	ACR_BAUD0,	MR0_BAUD_NORMAL,	1200, },
+	{ 10,	ACR_BAUD1,	MR0_BAUD_NORMAL,	1800, },
+	{ 7,	ACR_BAUD1,	MR0_BAUD_NORMAL,	2000, },
+	{ 8,	ACR_BAUD0,	MR0_BAUD_NORMAL,	2400, },
+	{ 5,	ACR_BAUD1,	MR0_BAUD_EXT1,		3600, },
+	{ 9,	ACR_BAUD0,	MR0_BAUD_NORMAL,	4800, },
+	{ 10,	ACR_BAUD0,	MR0_BAUD_NORMAL,	7200, },
+	{ 11,	ACR_BAUD0,	MR0_BAUD_NORMAL,	9600, },
+	{ 8,	ACR_BAUD0,	MR0_BAUD_EXT1,		14400, },
+	{ 12,	ACR_BAUD1,	MR0_BAUD_NORMAL,	19200, },
+	{ 9,	ACR_BAUD0,	MR0_BAUD_EXT1,		28800, },
+	{ 12,	ACR_BAUD0,	MR0_BAUD_NORMAL,	38400, },
+	{ 11,	ACR_BAUD0,	MR0_BAUD_EXT1,		57600, },
+	{ 12,	ACR_BAUD1,	MR0_BAUD_EXT1,		115200, },
+	{ 12,	ACR_BAUD0,	MR0_BAUD_EXT1,		230400, },
+	{ 0, 0, 0, 0 }
+};
+
+static void sccnxp_set_baud(struct uart_port *port, int baud)
+{
+	struct sccnxp_port *s = dev_get_drvdata(port->dev);
+	int div_std, tmp_baud, bestbaud = baud, besterr = -1;
+	u8 i, acr = 0, csr = 0, mr0 = 0;
+
+	/* Find best baud from table */
+	for (i = 0; baud_std[i].baud && besterr; i++) {
+		if (baud_std[i].mr0 && !(s->flags & SCCNXP_HAVE_MR0))
+			continue;
+		div_std = DIV_ROUND_CLOSEST(s->freq_std, baud_std[i].baud);
+		tmp_baud = DIV_ROUND_CLOSEST(port->uartclk, div_std);
+		if (!sccnxp_update_best_err(baud, tmp_baud, &besterr)) {
+			acr = baud_std[i].acr;
+			csr = baud_std[i].csr;
+			mr0 = baud_std[i].mr0;
+			bestbaud = tmp_baud;
+		}
+	}
+
+	if (s->flags & SCCNXP_HAVE_MR0) {
+		/* Enable FIFO, set half level for TX */
+		mr0 |= MR0_FIFO | MR0_TXLVL;
+		/* Update MR0 */
+		sccnxp_port_write(port, SCCNXP_CR_REG, CR_CMD_MRPTR0);
+		sccnxp_port_write(port, SCCNXP_MR_REG, mr0);
+	}
+
+	sccnxp_port_write(port, SCCNXP_ACR_REG, acr | ACR_TIMER_MODE);
+	sccnxp_port_write(port, SCCNXP_CSR_REG, (csr << 4) | csr);
+
+	dev_dbg(port->dev, "Baudrate desired: %i, calculated: %i\n",
+		baud, bestbaud);
+}
+
+static void sccnxp_enable_irq(struct uart_port *port, int mask)
+{
+	struct sccnxp_port *s = dev_get_drvdata(port->dev);
+
+	s->imr |= mask << (port->line * 4);
+	sccnxp_write(port, SCCNXP_IMR_REG, s->imr);
+}
+
+static void sccnxp_disable_irq(struct uart_port *port, int mask)
+{
+	struct sccnxp_port *s = dev_get_drvdata(port->dev);
+
+	s->imr &= ~(mask << (port->line * 4));
+	sccnxp_write(port, SCCNXP_IMR_REG, s->imr);
+}
+
+static void sccnxp_set_bit(struct uart_port *port, int sig, int state)
+{
+	u8 bitmask;
+	struct sccnxp_port *s = dev_get_drvdata(port->dev);
+
+	if (s->pdata.mctrl_cfg[port->line] & MCTRL_MASK(sig)) {
+		bitmask = 1 << MCTRL_OBIT(s->pdata.mctrl_cfg[port->line], sig);
+		if (state)
+			sccnxp_write(port, SCCNXP_SOP_REG, bitmask);
+		else
+			sccnxp_write(port, SCCNXP_ROP_REG, bitmask);
+	}
+}
+
+static void sccnxp_handle_rx(struct uart_port *port)
+{
+	u8 sr;
+	unsigned int ch, flag;
+	struct tty_struct *tty = tty_port_tty_get(&port->state->port);
+
+	if (!tty)
+		return;
+
+	for (;;) {
+		sr = sccnxp_port_read(port, SCCNXP_SR_REG);
+		if (!(sr & SR_RXRDY))
+			break;
+		sr &= SR_PE | SR_FE | SR_OVR | SR_BRK;
+
+		ch = sccnxp_port_read(port, SCCNXP_RHR_REG);
+
+		port->icount.rx++;
+		flag = TTY_NORMAL;
+
+		if (unlikely(sr)) {
+			if (sr & SR_BRK) {
+				port->icount.brk++;
+				if (uart_handle_break(port))
+					continue;
+			} else if (sr & SR_PE)
+				port->icount.parity++;
+			else if (sr & SR_FE)
+				port->icount.frame++;
+			else if (sr & SR_OVR)
+				port->icount.overrun++;
+
+			sr &= port->read_status_mask;
+			if (sr & SR_BRK)
+				flag = TTY_BREAK;
+			else if (sr & SR_PE)
+				flag = TTY_PARITY;
+			else if (sr & SR_FE)
+				flag = TTY_FRAME;
+			else if (sr & SR_OVR)
+				flag = TTY_OVERRUN;
+		}
+
+		if (uart_handle_sysrq_char(port, ch))
+			continue;
+
+		if (sr & port->ignore_status_mask)
+			continue;
+
+		uart_insert_char(port, sr, SR_OVR, ch, flag);
+	}
+
+	tty_flip_buffer_push(tty);
+
+	tty_kref_put(tty);
+}
+
+static void sccnxp_handle_tx(struct uart_port *port)
+{
+	u8 sr;
+	struct circ_buf *xmit = &port->state->xmit;
+	struct sccnxp_port *s = dev_get_drvdata(port->dev);
+
+	if (unlikely(port->x_char)) {
+		sccnxp_port_write(port, SCCNXP_THR_REG, port->x_char);
+		port->icount.tx++;
+		port->x_char = 0;
+		return;
+	}
+
+	if (uart_circ_empty(xmit) || uart_tx_stopped(port)) {
+		/* Disable TX if FIFO is empty */
+		if (sccnxp_port_read(port, SCCNXP_SR_REG) & SR_TXEMT) {
+			sccnxp_disable_irq(port, IMR_TXRDY);
+
+			/* Set direction to input */
+			if (s->flags & SCCNXP_HAVE_IO)
+				sccnxp_set_bit(port, DIR_OP, 0);
+		}
+		return;
+	}
+
+	while (!uart_circ_empty(xmit)) {
+		sr = sccnxp_port_read(port, SCCNXP_SR_REG);
+		if (!(sr & SR_TXRDY))
+			break;
+
+		sccnxp_port_write(port, SCCNXP_THR_REG, xmit->buf[xmit->tail]);
+		xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+		port->icount.tx++;
+	}
+
+	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+		uart_write_wakeup(port);
+}
+
+static irqreturn_t sccnxp_ist(int irq, void *dev_id)
+{
+	int i;
+	u8 isr;
+	struct sccnxp_port *s = (struct sccnxp_port *)dev_id;
+
+	mutex_lock(&s->sccnxp_mutex);
+
+	for (;;) {
+		isr = sccnxp_read(&s->port[0], SCCNXP_ISR_REG);
+		isr &= s->imr;
+		if (!isr)
+			break;
+
+		dev_dbg(s->port[0].dev, "IRQ status: 0x%02x\n", isr);
+
+		for (i = 0; i < s->uart.nr; i++) {
+			if (isr & ISR_RXRDY(i))
+				sccnxp_handle_rx(&s->port[i]);
+			if (isr & ISR_TXRDY(i))
+				sccnxp_handle_tx(&s->port[i]);
+		}
+	}
+
+	mutex_unlock(&s->sccnxp_mutex);
+
+	return IRQ_HANDLED;
+}
+
+static void sccnxp_start_tx(struct uart_port *port)
+{
+	struct sccnxp_port *s = dev_get_drvdata(port->dev);
+
+	mutex_lock(&s->sccnxp_mutex);
+
+	/* Set direction to output */
+	if (s->flags & SCCNXP_HAVE_IO)
+		sccnxp_set_bit(port, DIR_OP, 1);
+
+	sccnxp_enable_irq(port, IMR_TXRDY);
+
+	mutex_unlock(&s->sccnxp_mutex);
+}
+
+static void sccnxp_stop_tx(struct uart_port *port)
+{
+	/* Do nothing */
+}
+
+static void sccnxp_stop_rx(struct uart_port *port)
+{
+	struct sccnxp_port *s = dev_get_drvdata(port->dev);
+
+	mutex_lock(&s->sccnxp_mutex);
+	sccnxp_port_write(port, SCCNXP_CR_REG, CR_RX_DISABLE);
+	mutex_unlock(&s->sccnxp_mutex);
+}
+
+static unsigned int sccnxp_tx_empty(struct uart_port *port)
+{
+	u8 val;
+	struct sccnxp_port *s = dev_get_drvdata(port->dev);
+
+	mutex_lock(&s->sccnxp_mutex);
+	val = sccnxp_port_read(port, SCCNXP_SR_REG);
+	mutex_unlock(&s->sccnxp_mutex);
+
+	return (val & SR_TXEMT) ? TIOCSER_TEMT : 0;
+}
+
+static void sccnxp_enable_ms(struct uart_port *port)
+{
+	/* Do nothing */
+}
+
+static void sccnxp_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+	struct sccnxp_port *s = dev_get_drvdata(port->dev);
+
+	if (!(s->flags & SCCNXP_HAVE_IO))
+		return;
+
+	mutex_lock(&s->sccnxp_mutex);
+
+	sccnxp_set_bit(port, DTR_OP, mctrl & TIOCM_DTR);
+	sccnxp_set_bit(port, RTS_OP, mctrl & TIOCM_RTS);
+
+	mutex_unlock(&s->sccnxp_mutex);
+}
+
+static unsigned int sccnxp_get_mctrl(struct uart_port *port)
+{
+	u8 bitmask, ipr;
+	struct sccnxp_port *s = dev_get_drvdata(port->dev);
+	unsigned int mctrl = TIOCM_DSR | TIOCM_CTS | TIOCM_CAR;
+
+	if (!(s->flags & SCCNXP_HAVE_IO))
+		return mctrl;
+
+	mutex_lock(&s->sccnxp_mutex);
+
+	ipr = ~sccnxp_read(port, SCCNXP_IPCR_REG);
+
+	if (s->pdata.mctrl_cfg[port->line] & MCTRL_MASK(DSR_IP)) {
+		bitmask = 1 << MCTRL_IBIT(s->pdata.mctrl_cfg[port->line],
+					  DSR_IP);
+		mctrl &= ~TIOCM_DSR;
+		mctrl |= (ipr & bitmask) ? TIOCM_DSR : 0;
+	}
+	if (s->pdata.mctrl_cfg[port->line] & MCTRL_MASK(CTS_IP)) {
+		bitmask = 1 << MCTRL_IBIT(s->pdata.mctrl_cfg[port->line],
+					  CTS_IP);
+		mctrl &= ~TIOCM_CTS;
+		mctrl |= (ipr & bitmask) ? TIOCM_CTS : 0;
+	}
+	if (s->pdata.mctrl_cfg[port->line] & MCTRL_MASK(DCD_IP)) {
+		bitmask = 1 << MCTRL_IBIT(s->pdata.mctrl_cfg[port->line],
+					  DCD_IP);
+		mctrl &= ~TIOCM_CAR;
+		mctrl |= (ipr & bitmask) ? TIOCM_CAR : 0;
+	}
+	if (s->pdata.mctrl_cfg[port->line] & MCTRL_MASK(RNG_IP)) {
+		bitmask = 1 << MCTRL_IBIT(s->pdata.mctrl_cfg[port->line],
+					  RNG_IP);
+		mctrl &= ~TIOCM_RNG;
+		mctrl |= (ipr & bitmask) ? TIOCM_RNG : 0;
+	}
+
+	mutex_unlock(&s->sccnxp_mutex);
+
+	return mctrl;
+}
+
+static void sccnxp_break_ctl(struct uart_port *port, int break_state)
+{
+	struct sccnxp_port *s = dev_get_drvdata(port->dev);
+
+	mutex_lock(&s->sccnxp_mutex);
+	sccnxp_port_write(port, SCCNXP_CR_REG, break_state ?
+			  CR_CMD_START_BREAK : CR_CMD_STOP_BREAK);
+	mutex_unlock(&s->sccnxp_mutex);
+}
+
+static void sccnxp_set_termios(struct uart_port *port,
+			       struct ktermios *termios, struct ktermios *old)
+{
+	struct sccnxp_port *s = dev_get_drvdata(port->dev);
+	u8 mr1, mr2;
+	int baud;
+
+	mutex_lock(&s->sccnxp_mutex);
+
+	/* Mask termios capabilities we don't support */
+	termios->c_cflag &= ~CMSPAR;
+	termios->c_iflag &= ~(IXON | IXOFF | IXANY);
+
+	/* Disable RX & TX, reset break condition, status and FIFOs */
+	sccnxp_port_write(port, SCCNXP_CR_REG, CR_CMD_RX_RESET |
+					       CR_RX_DISABLE | CR_TX_DISABLE);
+	sccnxp_port_write(port, SCCNXP_CR_REG, CR_CMD_TX_RESET);
+	sccnxp_port_write(port, SCCNXP_CR_REG, CR_CMD_STATUS_RESET);
+	sccnxp_port_write(port, SCCNXP_CR_REG, CR_CMD_BREAK_RESET);
+
+	/* Word size */
+	switch (termios->c_cflag & CSIZE) {
+	case CS5:
+		mr1 = MR1_BITS_5;
+		break;
+	case CS6:
+		mr1 = MR1_BITS_6;
+		break;
+	case CS7:
+		mr1 = MR1_BITS_7;
+		break;
+	default:
+	case CS8:
+		mr1 = MR1_BITS_8;
+		break;
+	}
+
+	/* Parity */
+	if (termios->c_cflag & PARENB) {
+		if (termios->c_cflag & PARODD)
+			mr1 |= MR1_PAR_ODD;
+	} else
+		mr1 |= MR1_PAR_NO;
+
+	/* Stop bits */
+	mr2 = (termios->c_cflag & CSTOPB) ? MR2_STOP2 : MR2_STOP1;
+
+	/* Update desired format */
+	sccnxp_port_write(port, SCCNXP_CR_REG, CR_CMD_MRPTR1);
+	sccnxp_port_write(port, SCCNXP_MR_REG, mr1);
+	sccnxp_port_write(port, SCCNXP_MR_REG, mr2);
+
+	/* Set read status mask */
+	port->read_status_mask = SR_OVR;
+	if (termios->c_iflag & INPCK)
+		port->read_status_mask |= SR_PE | SR_FE;
+	if (termios->c_iflag & (BRKINT | PARMRK))
+		port->read_status_mask |= SR_BRK;
+
+	/* Set status ignore mask */
+	port->ignore_status_mask = 0;
+	if (termios->c_iflag & IGNBRK)
+		port->ignore_status_mask |= SR_BRK;
+	if (!(termios->c_cflag & CREAD))
+		port->ignore_status_mask |= SR_PE | SR_OVR | SR_FE | SR_BRK;
+
+	/* Setup baudrate */
+	baud = uart_get_baud_rate(port, termios, old, 50,
+				  (s->flags & SCCNXP_HAVE_MR0) ?
+				  230400 : 38400);
+	sccnxp_set_baud(port, baud);
+
+	/* Update timeout according to new baud rate */
+	uart_update_timeout(port, termios->c_cflag, baud);
+
+	/* Enable RX & TX */
+	sccnxp_port_write(port, SCCNXP_CR_REG, CR_RX_ENABLE | CR_TX_ENABLE);
+
+	mutex_unlock(&s->sccnxp_mutex);
+}
+
+static int sccnxp_startup(struct uart_port *port)
+{
+	struct sccnxp_port *s = dev_get_drvdata(port->dev);
+
+	mutex_lock(&s->sccnxp_mutex);
+
+	if (s->flags & SCCNXP_HAVE_IO) {
+		/* Outputs are controlled manually */
+		sccnxp_write(port, SCCNXP_OPCR_REG, 0);
+	}
+
+	/* Reset break condition, status and FIFOs */
+	sccnxp_port_write(port, SCCNXP_CR_REG, CR_CMD_RX_RESET);
+	sccnxp_port_write(port, SCCNXP_CR_REG, CR_CMD_TX_RESET);
+	sccnxp_port_write(port, SCCNXP_CR_REG, CR_CMD_STATUS_RESET);
+	sccnxp_port_write(port, SCCNXP_CR_REG, CR_CMD_BREAK_RESET);
+
+	/* Enable RX & TX */
+	sccnxp_port_write(port, SCCNXP_CR_REG, CR_RX_ENABLE | CR_TX_ENABLE);
+
+	/* Enable RX interrupt */
+	sccnxp_enable_irq(port, IMR_RXRDY);
+
+	mutex_unlock(&s->sccnxp_mutex);
+
+	return 0;
+}
+
+static void sccnxp_shutdown(struct uart_port *port)
+{
+	struct sccnxp_port *s = dev_get_drvdata(port->dev);
+
+	mutex_lock(&s->sccnxp_mutex);
+
+	/* Disable interrupts */
+	sccnxp_disable_irq(port, IMR_TXRDY | IMR_RXRDY);
+
+	/* Disable TX & RX */
+	sccnxp_port_write(port, SCCNXP_CR_REG, CR_RX_DISABLE | CR_TX_DISABLE);
+
+	/* Leave direction to input */
+	if (s->flags & SCCNXP_HAVE_IO)
+		sccnxp_set_bit(port, DIR_OP, 0);
+
+	mutex_unlock(&s->sccnxp_mutex);
+}
+
+static const char *sccnxp_type(struct uart_port *port)
+{
+	struct sccnxp_port *s = dev_get_drvdata(port->dev);
+
+	return (port->type == PORT_SC26XX) ? s->name : NULL;
+}
+
+static void sccnxp_release_port(struct uart_port *port)
+{
+	/* Do nothing */
+}
+
+static int sccnxp_request_port(struct uart_port *port)
+{
+	/* Do nothing */
+	return 0;
+}
+
+static void sccnxp_config_port(struct uart_port *port, int flags)
+{
+	if (flags & UART_CONFIG_TYPE)
+		port->type = PORT_SC26XX;
+}
+
+static int sccnxp_verify_port(struct uart_port *port, struct serial_struct *s)
+{
+	if ((s->type == PORT_UNKNOWN) || (s->type == PORT_SC26XX))
+		return 0;
+	if (s->irq == port->irq)
+		return 0;
+
+	return -EINVAL;
+}
+
+static const struct uart_ops sccnxp_ops = {
+	.tx_empty	= sccnxp_tx_empty,
+	.set_mctrl	= sccnxp_set_mctrl,
+	.get_mctrl	= sccnxp_get_mctrl,
+	.stop_tx	= sccnxp_stop_tx,
+	.start_tx	= sccnxp_start_tx,
+	.stop_rx	= sccnxp_stop_rx,
+	.enable_ms	= sccnxp_enable_ms,
+	.break_ctl	= sccnxp_break_ctl,
+	.startup	= sccnxp_startup,
+	.shutdown	= sccnxp_shutdown,
+	.set_termios	= sccnxp_set_termios,
+	.type		= sccnxp_type,
+	.release_port	= sccnxp_release_port,
+	.request_port	= sccnxp_request_port,
+	.config_port	= sccnxp_config_port,
+	.verify_port	= sccnxp_verify_port,
+};
+
+#ifdef CONFIG_SERIAL_SCCNXP_CONSOLE
+static void sccnxp_console_putchar(struct uart_port *port, int c)
+{
+	int tryes = 100000;
+
+	while (tryes--) {
+		if (sccnxp_port_read(port, SCCNXP_SR_REG) & SR_TXRDY) {
+			sccnxp_port_write(port, SCCNXP_THR_REG, c);
+			break;
+		}
+		barrier();
+	}
+}
+
+static void sccnxp_console_write(struct console *co, const char *c, unsigned n)
+{
+	struct sccnxp_port *s = (struct sccnxp_port *)co->data;
+	struct uart_port *port = &s->port[co->index];
+
+	mutex_lock(&s->sccnxp_mutex);
+	uart_console_write(port, c, n, sccnxp_console_putchar);
+	mutex_unlock(&s->sccnxp_mutex);
+}
+
+static int sccnxp_console_setup(struct console *co, char *options)
+{
+	struct sccnxp_port *s = (struct sccnxp_port *)co->data;
+	struct uart_port *port = &s->port[(co->index > 0) ? co->index : 0];
+	int baud = 9600, bits = 8, parity = 'n', flow = 'n';
+
+	if (options)
+		uart_parse_options(options, &baud, &parity, &bits, &flow);
+
+	return uart_set_options(port, co, baud, parity, bits, flow);
+}
+#endif
+
+static int __devinit sccnxp_probe(struct platform_device *pdev)
+{
+	struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	int chiptype = pdev->id_entry->driver_data;
+	struct sccnxp_pdata *pdata = dev_get_platdata(&pdev->dev);
+	int i, ret, fifosize, freq_min, freq_max;
+	struct sccnxp_port *s;
+	void __iomem *membase;
+
+	if (!res) {
+		dev_err(&pdev->dev, "Missing memory resource data\n");
+		return -EADDRNOTAVAIL;
+	}
+
+	dev_set_name(&pdev->dev, SCCNXP_NAME);
+
+	s = devm_kzalloc(&pdev->dev, sizeof(struct sccnxp_port), GFP_KERNEL);
+	if (!s) {
+		dev_err(&pdev->dev, "Error allocating port structure\n");
+		return -ENOMEM;
+	}
+	platform_set_drvdata(pdev, s);
+
+	mutex_init(&s->sccnxp_mutex);
+
+	/* Individual chip settings */
+	switch (chiptype) {
+	case SCCNXP_TYPE_SC2681:
+		s->name		= "SC2681";
+		s->uart.nr	= 2;
+		s->freq_std	= 3686400;
+		s->addr_mask	= 0x0f;
+		s->flags	= SCCNXP_HAVE_IO;
+		fifosize	= 3;
+		freq_min	= 1000000;
+		freq_max	= 4000000;
+		break;
+	case SCCNXP_TYPE_SC2691:
+		s->name		= "SC2691";
+		s->uart.nr	= 1;
+		s->freq_std	= 3686400;
+		s->addr_mask	= 0x07;
+		s->flags	= 0;
+		fifosize	= 3;
+		freq_min	= 1000000;
+		freq_max	= 4000000;
+		break;
+	case SCCNXP_TYPE_SC2692:
+		s->name		= "SC2692";
+		s->uart.nr	= 2;
+		s->freq_std	= 3686400;
+		s->addr_mask	= 0x0f;
+		s->flags	= SCCNXP_HAVE_IO;
+		fifosize	= 3;
+		freq_min	= 1000000;
+		freq_max	= 4000000;
+		break;
+	case SCCNXP_TYPE_SC2891:
+		s->name		= "SC2891";
+		s->uart.nr	= 1;
+		s->freq_std	= 3686400;
+		s->addr_mask	= 0x0f;
+		s->flags	= SCCNXP_HAVE_IO | SCCNXP_HAVE_MR0;
+		fifosize	= 16;
+		freq_min	= 100000;
+		freq_max	= 8000000;
+		break;
+	case SCCNXP_TYPE_SC2892:
+		s->name		= "SC2892";
+		s->uart.nr	= 2;
+		s->freq_std	= 3686400;
+		s->addr_mask	= 0x0f;
+		s->flags	= SCCNXP_HAVE_IO | SCCNXP_HAVE_MR0;
+		fifosize	= 16;
+		freq_min	= 100000;
+		freq_max	= 8000000;
+		break;
+	case SCCNXP_TYPE_SC28202:
+		s->name		= "SC28202";
+		s->uart.nr	= 2;
+		s->freq_std	= 14745600;
+		s->addr_mask	= 0x7f;
+		s->flags	= SCCNXP_HAVE_IO | SCCNXP_HAVE_MR0;
+		fifosize	= 256;
+		freq_min	= 1000000;
+		freq_max	= 50000000;
+		break;
+	case SCCNXP_TYPE_SC68681:
+		s->name		= "SC68681";
+		s->uart.nr	= 2;
+		s->freq_std	= 3686400;
+		s->addr_mask	= 0x0f;
+		s->flags	= SCCNXP_HAVE_IO;
+		fifosize	= 3;
+		freq_min	= 1000000;
+		freq_max	= 4000000;
+		break;
+	case SCCNXP_TYPE_SC68692:
+		s->name		= "SC68692";
+		s->uart.nr	= 2;
+		s->freq_std	= 3686400;
+		s->addr_mask	= 0x0f;
+		s->flags	= SCCNXP_HAVE_IO;
+		fifosize	= 3;
+		freq_min	= 1000000;
+		freq_max	= 4000000;
+		break;
+	default:
+		dev_err(&pdev->dev, "Unsupported chip type %i\n", chiptype);
+		ret = -ENOTSUPP;
+		goto err_out;
+	}
+
+	if (!pdata) {
+		dev_warn(&pdev->dev,
+			 "No platform data supplied, using defaults\n");
+		s->pdata.frequency = s->freq_std;
+	} else
+		memcpy(&s->pdata, pdata, sizeof(struct sccnxp_pdata));
+
+	s->irq = platform_get_irq(pdev, 0);
+	if (s->irq <= 0) {
+		dev_err(&pdev->dev, "Missing irq resource data\n");
+		ret = -ENXIO;
+		goto err_out;
+	}
+
+	/* Check input frequency */
+	if ((s->pdata.frequency < freq_min) ||
+	    (s->pdata.frequency > freq_max)) {
+		dev_err(&pdev->dev, "Frequency out of bounds\n");
+		ret = -EINVAL;
+		goto err_out;
+	}
+
+	membase = devm_request_and_ioremap(&pdev->dev, res);
+	if (!membase) {
+		dev_err(&pdev->dev, "Failed to ioremap\n");
+		ret = -EIO;
+		goto err_out;
+	}
+
+	s->uart.owner		= THIS_MODULE;
+	s->uart.dev_name	= "ttySC";
+	s->uart.major		= SCCNXP_MAJOR;
+	s->uart.minor		= SCCNXP_MINOR;
+#ifdef CONFIG_SERIAL_SCCNXP_CONSOLE
+	s->uart.cons		= &s->console;
+	s->uart.cons->device	= uart_console_device;
+	s->uart.cons->write	= sccnxp_console_write;
+	s->uart.cons->setup	= sccnxp_console_setup;
+	s->uart.cons->flags	= CON_PRINTBUFFER;
+	s->uart.cons->index	= -1;
+	s->uart.cons->data	= s;
+	strcpy(s->uart.cons->name, "ttySC");
+#endif
+	ret = uart_register_driver(&s->uart);
+	if (ret) {
+		dev_err(&pdev->dev, "Registering UART driver failed\n");
+		goto err_out;
+	}
+
+	for (i = 0; i < s->uart.nr; i++) {
+		s->port[i].line		= i;
+		s->port[i].dev		= &pdev->dev;
+		s->port[i].irq		= s->irq;
+		s->port[i].type		= PORT_SC26XX;
+		s->port[i].fifosize	= fifosize;
+		s->port[i].flags	= UPF_SKIP_TEST | UPF_FIXED_TYPE;
+		s->port[i].iotype	= UPIO_MEM;
+		s->port[i].mapbase	= res->start;
+		s->port[i].membase	= membase;
+		s->port[i].regshift	= s->pdata.reg_shift;
+		s->port[i].uartclk	= s->pdata.frequency;
+		s->port[i].ops		= &sccnxp_ops;
+		uart_add_one_port(&s->uart, &s->port[i]);
+		/* Set direction to input */
+		if (s->flags & SCCNXP_HAVE_IO)
+			sccnxp_set_bit(&s->port[i], DIR_OP, 0);
+	}
+
+	/* Disable interrupts */
+	s->imr = 0;
+	sccnxp_write(&s->port[0], SCCNXP_IMR_REG, 0);
+
+	/* Board specific configure */
+	if (s->pdata.init)
+		s->pdata.init();
+
+	ret = devm_request_threaded_irq(&pdev->dev, s->irq, NULL, sccnxp_ist,
+					IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
+					dev_name(&pdev->dev), s);
+	if (!ret)
+		return 0;
+
+	dev_err(&pdev->dev, "Unable to reguest IRQ %i\n", s->irq);
+
+err_out:
+	platform_set_drvdata(pdev, NULL);
+
+	return ret;
+}
+
+static int __devexit sccnxp_remove(struct platform_device *pdev)
+{
+	int i;
+	struct sccnxp_port *s = platform_get_drvdata(pdev);
+
+	devm_free_irq(&pdev->dev, s->irq, s);
+
+	for (i = 0; i < s->uart.nr; i++)
+		uart_remove_one_port(&s->uart, &s->port[i]);
+
+	uart_unregister_driver(&s->uart);
+	platform_set_drvdata(pdev, NULL);
+
+	if (s->pdata.exit)
+		s->pdata.exit();
+
+	return 0;
+}
+
+static const struct platform_device_id sccnxp_id_table[] = {
+	{ "sc2681",	SCCNXP_TYPE_SC2681 },
+	{ "sc2691",	SCCNXP_TYPE_SC2691 },
+	{ "sc2692",	SCCNXP_TYPE_SC2692 },
+	{ "sc2891",	SCCNXP_TYPE_SC2891 },
+	{ "sc2892",	SCCNXP_TYPE_SC2892 },
+	{ "sc28202",	SCCNXP_TYPE_SC28202 },
+	{ "sc68681",	SCCNXP_TYPE_SC68681 },
+	{ "sc68692",	SCCNXP_TYPE_SC68692 },
+};
+MODULE_DEVICE_TABLE(platform, sccnxp_id_table);
+
+static struct platform_driver sccnxp_uart_driver = {
+	.driver = {
+		.name	= SCCNXP_NAME,
+		.owner	= THIS_MODULE,
+	},
+	.probe		= sccnxp_probe,
+	.remove		= __devexit_p(sccnxp_remove),
+	.id_table	= sccnxp_id_table,
+};
+module_platform_driver(sccnxp_uart_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Alexander Shiyan <shc_work@mail.ru>");
+MODULE_DESCRIPTION("SCCNXP serial driver");
diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c
index a21dc8e..046279c 100644
--- a/drivers/tty/serial/serial_core.c
+++ b/drivers/tty/serial/serial_core.c
@@ -159,7 +159,7 @@
 	retval = uport->ops->startup(uport);
 	if (retval == 0) {
 		if (uart_console(uport) && uport->cons->cflag) {
-			tty->termios->c_cflag = uport->cons->cflag;
+			tty->termios.c_cflag = uport->cons->cflag;
 			uport->cons->cflag = 0;
 		}
 		/*
@@ -172,11 +172,11 @@
 			 * Setup the RTS and DTR signals once the
 			 * port is open and ready to respond.
 			 */
-			if (tty->termios->c_cflag & CBAUD)
+			if (tty->termios.c_cflag & CBAUD)
 				uart_set_mctrl(uport, TIOCM_RTS | TIOCM_DTR);
 		}
 
-		if (port->flags & ASYNC_CTS_FLOW) {
+		if (tty_port_cts_enabled(port)) {
 			spin_lock_irq(&uport->lock);
 			if (!(uport->ops->get_mctrl(uport) & TIOCM_CTS))
 				tty->hw_stopped = 1;
@@ -240,7 +240,7 @@
 		/*
 		 * Turn off DTR and RTS early.
 		 */
-		if (!tty || (tty->termios->c_cflag & HUPCL))
+		if (!tty || (tty->termios.c_cflag & HUPCL))
 			uart_clear_mctrl(uport, TIOCM_DTR | TIOCM_RTS);
 
 		uart_port_shutdown(port);
@@ -440,10 +440,10 @@
 	 * If we have no tty, termios, or the port does not exist,
 	 * then we can't set the parameters for this port.
 	 */
-	if (!tty || !tty->termios || uport->type == PORT_UNKNOWN)
+	if (!tty || uport->type == PORT_UNKNOWN)
 		return;
 
-	termios = tty->termios;
+	termios = &tty->termios;
 
 	/*
 	 * Set flags based on termios cflag
@@ -614,7 +614,7 @@
 	if (I_IXOFF(tty))
 		uart_send_xchar(tty, STOP_CHAR(tty));
 
-	if (tty->termios->c_cflag & CRTSCTS)
+	if (tty->termios.c_cflag & CRTSCTS)
 		uart_clear_mctrl(state->uart_port, TIOCM_RTS);
 }
 
@@ -630,42 +630,48 @@
 			uart_send_xchar(tty, START_CHAR(tty));
 	}
 
-	if (tty->termios->c_cflag & CRTSCTS)
+	if (tty->termios.c_cflag & CRTSCTS)
 		uart_set_mctrl(port, TIOCM_RTS);
 }
 
-static int uart_get_info(struct uart_state *state,
-			 struct serial_struct __user *retinfo)
+static void uart_get_info(struct tty_port *port,
+                        struct uart_state *state,
+			struct serial_struct *retinfo)
 {
 	struct uart_port *uport = state->uart_port;
+
+	memset(retinfo, 0, sizeof(*retinfo));
+
+	retinfo->type	    = uport->type;
+	retinfo->line	    = uport->line;
+	retinfo->port	    = uport->iobase;
+	if (HIGH_BITS_OFFSET)
+		retinfo->port_high = (long) uport->iobase >> HIGH_BITS_OFFSET;
+	retinfo->irq		    = uport->irq;
+	retinfo->flags	    = uport->flags;
+	retinfo->xmit_fifo_size  = uport->fifosize;
+	retinfo->baud_base	    = uport->uartclk / 16;
+	retinfo->close_delay	    = jiffies_to_msecs(port->close_delay) / 10;
+	retinfo->closing_wait    = port->closing_wait == ASYNC_CLOSING_WAIT_NONE ?
+				ASYNC_CLOSING_WAIT_NONE :
+				jiffies_to_msecs(port->closing_wait) / 10;
+	retinfo->custom_divisor  = uport->custom_divisor;
+	retinfo->hub6	    = uport->hub6;
+	retinfo->io_type         = uport->iotype;
+	retinfo->iomem_reg_shift = uport->regshift;
+	retinfo->iomem_base      = (void *)(unsigned long)uport->mapbase;
+}
+
+static int uart_get_info_user(struct uart_state *state,
+			 struct serial_struct __user *retinfo)
+{
 	struct tty_port *port = &state->port;
 	struct serial_struct tmp;
 
-	memset(&tmp, 0, sizeof(tmp));
-
 	/* Ensure the state we copy is consistent and no hardware changes
 	   occur as we go */
 	mutex_lock(&port->mutex);
-
-	tmp.type	    = uport->type;
-	tmp.line	    = uport->line;
-	tmp.port	    = uport->iobase;
-	if (HIGH_BITS_OFFSET)
-		tmp.port_high = (long) uport->iobase >> HIGH_BITS_OFFSET;
-	tmp.irq		    = uport->irq;
-	tmp.flags	    = uport->flags;
-	tmp.xmit_fifo_size  = uport->fifosize;
-	tmp.baud_base	    = uport->uartclk / 16;
-	tmp.close_delay	    = jiffies_to_msecs(port->close_delay) / 10;
-	tmp.closing_wait    = port->closing_wait == ASYNC_CLOSING_WAIT_NONE ?
-				ASYNC_CLOSING_WAIT_NONE :
-				jiffies_to_msecs(port->closing_wait) / 10;
-	tmp.custom_divisor  = uport->custom_divisor;
-	tmp.hub6	    = uport->hub6;
-	tmp.io_type         = uport->iotype;
-	tmp.iomem_reg_shift = uport->regshift;
-	tmp.iomem_base      = (void *)(unsigned long)uport->mapbase;
-
+	uart_get_info(port, state, &tmp);
 	mutex_unlock(&port->mutex);
 
 	if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
@@ -673,42 +679,30 @@
 	return 0;
 }
 
-static int uart_set_info(struct tty_struct *tty, struct uart_state *state,
-			 struct serial_struct __user *newinfo)
+static int uart_set_info(struct tty_struct *tty, struct tty_port *port,
+			 struct uart_state *state,
+			 struct serial_struct *new_info)
 {
-	struct serial_struct new_serial;
 	struct uart_port *uport = state->uart_port;
-	struct tty_port *port = &state->port;
 	unsigned long new_port;
 	unsigned int change_irq, change_port, closing_wait;
 	unsigned int old_custom_divisor, close_delay;
 	upf_t old_flags, new_flags;
 	int retval = 0;
 
-	if (copy_from_user(&new_serial, newinfo, sizeof(new_serial)))
-		return -EFAULT;
-
-	new_port = new_serial.port;
+	new_port = new_info->port;
 	if (HIGH_BITS_OFFSET)
-		new_port += (unsigned long) new_serial.port_high << HIGH_BITS_OFFSET;
+		new_port += (unsigned long) new_info->port_high << HIGH_BITS_OFFSET;
 
-	new_serial.irq = irq_canonicalize(new_serial.irq);
-	close_delay = msecs_to_jiffies(new_serial.close_delay * 10);
-	closing_wait = new_serial.closing_wait == ASYNC_CLOSING_WAIT_NONE ?
+	new_info->irq = irq_canonicalize(new_info->irq);
+	close_delay = msecs_to_jiffies(new_info->close_delay * 10);
+	closing_wait = new_info->closing_wait == ASYNC_CLOSING_WAIT_NONE ?
 			ASYNC_CLOSING_WAIT_NONE :
-			msecs_to_jiffies(new_serial.closing_wait * 10);
+			msecs_to_jiffies(new_info->closing_wait * 10);
 
-	/*
-	 * This semaphore protects port->count.  It is also
-	 * very useful to prevent opens.  Also, take the
-	 * port configuration semaphore to make sure that a
-	 * module insertion/removal doesn't change anything
-	 * under us.
-	 */
-	mutex_lock(&port->mutex);
 
 	change_irq  = !(uport->flags & UPF_FIXED_PORT)
-		&& new_serial.irq != uport->irq;
+		&& new_info->irq != uport->irq;
 
 	/*
 	 * Since changing the 'type' of the port changes its resource
@@ -717,29 +711,29 @@
 	 */
 	change_port = !(uport->flags & UPF_FIXED_PORT)
 		&& (new_port != uport->iobase ||
-		    (unsigned long)new_serial.iomem_base != uport->mapbase ||
-		    new_serial.hub6 != uport->hub6 ||
-		    new_serial.io_type != uport->iotype ||
-		    new_serial.iomem_reg_shift != uport->regshift ||
-		    new_serial.type != uport->type);
+		    (unsigned long)new_info->iomem_base != uport->mapbase ||
+		    new_info->hub6 != uport->hub6 ||
+		    new_info->io_type != uport->iotype ||
+		    new_info->iomem_reg_shift != uport->regshift ||
+		    new_info->type != uport->type);
 
 	old_flags = uport->flags;
-	new_flags = new_serial.flags;
+	new_flags = new_info->flags;
 	old_custom_divisor = uport->custom_divisor;
 
 	if (!capable(CAP_SYS_ADMIN)) {
 		retval = -EPERM;
 		if (change_irq || change_port ||
-		    (new_serial.baud_base != uport->uartclk / 16) ||
+		    (new_info->baud_base != uport->uartclk / 16) ||
 		    (close_delay != port->close_delay) ||
 		    (closing_wait != port->closing_wait) ||
-		    (new_serial.xmit_fifo_size &&
-		     new_serial.xmit_fifo_size != uport->fifosize) ||
+		    (new_info->xmit_fifo_size &&
+		     new_info->xmit_fifo_size != uport->fifosize) ||
 		    (((new_flags ^ old_flags) & ~UPF_USR_MASK) != 0))
 			goto exit;
 		uport->flags = ((uport->flags & ~UPF_USR_MASK) |
 			       (new_flags & UPF_USR_MASK));
-		uport->custom_divisor = new_serial.custom_divisor;
+		uport->custom_divisor = new_info->custom_divisor;
 		goto check_and_exit;
 	}
 
@@ -747,10 +741,10 @@
 	 * Ask the low level driver to verify the settings.
 	 */
 	if (uport->ops->verify_port)
-		retval = uport->ops->verify_port(uport, &new_serial);
+		retval = uport->ops->verify_port(uport, new_info);
 
-	if ((new_serial.irq >= nr_irqs) || (new_serial.irq < 0) ||
-	    (new_serial.baud_base < 9600))
+	if ((new_info->irq >= nr_irqs) || (new_info->irq < 0) ||
+	    (new_info->baud_base < 9600))
 		retval = -EINVAL;
 
 	if (retval)
@@ -790,11 +784,11 @@
 			uport->ops->release_port(uport);
 
 		uport->iobase = new_port;
-		uport->type = new_serial.type;
-		uport->hub6 = new_serial.hub6;
-		uport->iotype = new_serial.io_type;
-		uport->regshift = new_serial.iomem_reg_shift;
-		uport->mapbase = (unsigned long)new_serial.iomem_base;
+		uport->type = new_info->type;
+		uport->hub6 = new_info->hub6;
+		uport->iotype = new_info->io_type;
+		uport->regshift = new_info->iomem_reg_shift;
+		uport->mapbase = (unsigned long)new_info->iomem_base;
 
 		/*
 		 * Claim and map the new regions
@@ -835,16 +829,16 @@
 	}
 
 	if (change_irq)
-		uport->irq      = new_serial.irq;
+		uport->irq      = new_info->irq;
 	if (!(uport->flags & UPF_FIXED_PORT))
-		uport->uartclk  = new_serial.baud_base * 16;
+		uport->uartclk  = new_info->baud_base * 16;
 	uport->flags            = (uport->flags & ~UPF_CHANGE_MASK) |
 				 (new_flags & UPF_CHANGE_MASK);
-	uport->custom_divisor   = new_serial.custom_divisor;
+	uport->custom_divisor   = new_info->custom_divisor;
 	port->close_delay     = close_delay;
 	port->closing_wait    = closing_wait;
-	if (new_serial.xmit_fifo_size)
-		uport->fifosize = new_serial.xmit_fifo_size;
+	if (new_info->xmit_fifo_size)
+		uport->fifosize = new_info->xmit_fifo_size;
 	if (port->tty)
 		port->tty->low_latency =
 			(uport->flags & UPF_LOW_LATENCY) ? 1 : 0;
@@ -873,6 +867,28 @@
 	} else
 		retval = uart_startup(tty, state, 1);
  exit:
+	return retval;
+}
+
+static int uart_set_info_user(struct tty_struct *tty, struct uart_state *state,
+			 struct serial_struct __user *newinfo)
+{
+	struct serial_struct new_serial;
+	struct tty_port *port = &state->port;
+	int retval;
+
+	if (copy_from_user(&new_serial, newinfo, sizeof(new_serial)))
+		return -EFAULT;
+
+	/*
+	 * This semaphore protects port->count.  It is also
+	 * very useful to prevent opens.  Also, take the
+	 * port configuration semaphore to make sure that a
+	 * module insertion/removal doesn't change anything
+	 * under us.
+	 */
+	mutex_lock(&port->mutex);
+	retval = uart_set_info(tty, port, state, &new_serial);
 	mutex_unlock(&port->mutex);
 	return retval;
 }
@@ -1115,11 +1131,11 @@
 	 */
 	switch (cmd) {
 	case TIOCGSERIAL:
-		ret = uart_get_info(state, uarg);
+		ret = uart_get_info_user(state, uarg);
 		break;
 
 	case TIOCSSERIAL:
-		ret = uart_set_info(tty, state, uarg);
+		ret = uart_set_info_user(tty, state, uarg);
 		break;
 
 	case TIOCSERCONFIG:
@@ -1187,7 +1203,7 @@
 	struct uart_port *uport = state->uart_port;
 
 	if (uport->ops->set_ldisc)
-		uport->ops->set_ldisc(uport, tty->termios->c_line);
+		uport->ops->set_ldisc(uport, tty->termios.c_line);
 }
 
 static void uart_set_termios(struct tty_struct *tty,
@@ -1195,7 +1211,7 @@
 {
 	struct uart_state *state = tty->driver_data;
 	unsigned long flags;
-	unsigned int cflag = tty->termios->c_cflag;
+	unsigned int cflag = tty->termios.c_cflag;
 
 
 	/*
@@ -1206,9 +1222,9 @@
 	 */
 #define RELEVANT_IFLAG(iflag)	((iflag) & (IGNBRK|BRKINT|IGNPAR|PARMRK|INPCK))
 	if ((cflag ^ old_termios->c_cflag) == 0 &&
-	    tty->termios->c_ospeed == old_termios->c_ospeed &&
-	    tty->termios->c_ispeed == old_termios->c_ispeed &&
-	    RELEVANT_IFLAG(tty->termios->c_iflag ^ old_termios->c_iflag) == 0) {
+	    tty->termios.c_ospeed == old_termios->c_ospeed &&
+	    tty->termios.c_ispeed == old_termios->c_ispeed &&
+	    RELEVANT_IFLAG(tty->termios.c_iflag ^ old_termios->c_iflag) == 0) {
 		return;
 	}
 
@@ -1960,8 +1976,8 @@
 		/*
 		 * If that's unset, use the tty termios setting.
 		 */
-		if (port->tty && port->tty->termios && termios.c_cflag == 0)
-			termios = *(port->tty->termios);
+		if (port->tty && termios.c_cflag == 0)
+			termios = port->tty->termios;
 
 		if (console_suspend_enabled)
 			uart_change_pm(state, 0);
@@ -2293,6 +2309,36 @@
 	return p->tty_driver;
 }
 
+static ssize_t uart_get_attr_uartclk(struct device *dev,
+	struct device_attribute *attr, char *buf)
+{
+	int ret;
+	struct tty_port *port = dev_get_drvdata(dev);
+	struct uart_state *state = container_of(port, struct uart_state, port);
+
+	mutex_lock(&state->port.mutex);
+	ret = snprintf(buf, PAGE_SIZE, "%d\n", state->uart_port->uartclk);
+	mutex_unlock(&state->port.mutex);
+
+	return ret;
+}
+
+static DEVICE_ATTR(uartclk, S_IRUSR | S_IRGRP, uart_get_attr_uartclk, NULL);
+
+static struct attribute *tty_dev_attrs[] = {
+	&dev_attr_uartclk.attr,
+	NULL,
+	};
+
+static const struct attribute_group tty_dev_attr_group = {
+	.attrs = tty_dev_attrs,
+	};
+
+static const struct attribute_group *tty_dev_attr_groups[] = {
+	&tty_dev_attr_group,
+	NULL
+	};
+
 /**
  *	uart_add_one_port - attach a driver-defined port structure
  *	@drv: pointer to the uart low level driver structure for this port
@@ -2346,7 +2392,8 @@
 	 * Register the port whether it's detected or not.  This allows
 	 * setserial to be used to alter this ports parameters.
 	 */
-	tty_dev = tty_register_device(drv->tty_driver, uport->line, uport->dev);
+	tty_dev = tty_port_register_device_attr(port, drv->tty_driver,
+			uport->line, uport->dev, port, tty_dev_attr_groups);
 	if (likely(!IS_ERR(tty_dev))) {
 		device_set_wakeup_capable(tty_dev, 1);
 	} else {
@@ -2492,7 +2539,7 @@
 
 	uport->icount.cts++;
 
-	if (port->flags & ASYNC_CTS_FLOW) {
+	if (tty_port_cts_enabled(port)) {
 		if (tty->hw_stopped) {
 			if (status) {
 				tty->hw_stopped = 0;
diff --git a/drivers/tty/serial/sirfsoc_uart.c b/drivers/tty/serial/sirfsoc_uart.c
index 5b3eda2..a9e2bd1 100644
--- a/drivers/tty/serial/sirfsoc_uart.c
+++ b/drivers/tty/serial/sirfsoc_uart.c
@@ -668,7 +668,7 @@
 	if (res == NULL) {
 		dev_err(&pdev->dev, "Insufficient resources.\n");
 		ret = -EFAULT;
-		goto irq_err;
+		goto err;
 	}
 	port->irq = res->start;
 
@@ -676,7 +676,7 @@
 		sirfport->p = pinctrl_get_select_default(&pdev->dev);
 		ret = IS_ERR(sirfport->p);
 		if (ret)
-			goto pin_err;
+			goto err;
 	}
 
 	port->ops = &sirfsoc_uart_ops;
@@ -695,9 +695,6 @@
 	platform_set_drvdata(pdev, NULL);
 	if (sirfport->hw_flow_ctrl)
 		pinctrl_put(sirfport->p);
-pin_err:
-irq_err:
-	devm_iounmap(&pdev->dev, port->membase);
 err:
 	return ret;
 }
@@ -709,7 +706,6 @@
 	platform_set_drvdata(pdev, NULL);
 	if (sirfport->hw_flow_ctrl)
 		pinctrl_put(sirfport->p);
-	devm_iounmap(&pdev->dev, port->membase);
 	uart_remove_one_port(&sirfsoc_uart_drv, port);
 	return 0;
 }
diff --git a/drivers/tty/serial/sunsu.c b/drivers/tty/serial/sunsu.c
index 675303b..b97913d 100644
--- a/drivers/tty/serial/sunsu.c
+++ b/drivers/tty/serial/sunsu.c
@@ -58,10 +58,16 @@
 enum su_type { SU_PORT_NONE, SU_PORT_MS, SU_PORT_KBD, SU_PORT_PORT };
 static char *su_typev[] = { "su(???)", "su(mouse)", "su(kbd)", "su(serial)" };
 
+struct serial_uart_config {
+	char	*name;
+	int	dfl_xmit_fifo_size;
+	int	flags;
+};
+
 /*
  * Here we define the default xmit fifo size used for each type of UART.
  */
-static const struct serial_uart_config uart_config[PORT_MAX_8250+1] = {
+static const struct serial_uart_config uart_config[] = {
 	{ "unknown",	1,	0 },
 	{ "8250",	1,	0 },
 	{ "16450",	1,	0 },
diff --git a/drivers/tty/synclink.c b/drivers/tty/synclink.c
index 593d40a..70e3a52 100644
--- a/drivers/tty/synclink.c
+++ b/drivers/tty/synclink.c
@@ -1359,7 +1359,7 @@
 			}
 		}
 	
-		if ( (info->port.flags & ASYNC_CTS_FLOW) && 
+		if (tty_port_cts_enabled(&info->port) &&
 		     (status & MISCSTATUS_CTS_LATCHED) ) {
 			if (info->port.tty->hw_stopped) {
 				if (status & MISCSTATUS_CTS) {
@@ -1840,22 +1840,22 @@
 	usc_DisableInterrupts(info,RECEIVE_DATA + RECEIVE_STATUS +
 		TRANSMIT_DATA + TRANSMIT_STATUS + IO_PIN + MISC );
 	usc_DisableDmaInterrupts(info,DICR_MASTER + DICR_TRANSMIT + DICR_RECEIVE);
-	
+
 	/* Disable DMAEN (Port 7, Bit 14) */
 	/* This disconnects the DMA request signal from the ISA bus */
 	/* on the ISA adapter. This has no effect for the PCI adapter */
 	usc_OutReg(info, PCR, (u16)((usc_InReg(info, PCR) | BIT15) | BIT14));
-	
+
 	/* Disable INTEN (Port 6, Bit12) */
 	/* This disconnects the IRQ request signal to the ISA bus */
 	/* on the ISA adapter. This has no effect for the PCI adapter */
 	usc_OutReg(info, PCR, (u16)((usc_InReg(info, PCR) | BIT13) | BIT12));
-	
- 	if (!info->port.tty || info->port.tty->termios->c_cflag & HUPCL) {
+
+	if (!info->port.tty || info->port.tty->termios.c_cflag & HUPCL) {
  		info->serial_signals &= ~(SerialSignal_DTR + SerialSignal_RTS);
 		usc_set_serial_signals(info);
 	}
-	
+
 	spin_unlock_irqrestore(&info->irq_spinlock,flags);
 
 	mgsl_release_resources(info);	
@@ -1895,7 +1895,7 @@
 	usc_EnableInterrupts(info, IO_PIN);
 	usc_get_serial_signals(info);
 		
-	if (info->netcount || info->port.tty->termios->c_cflag & CREAD)
+	if (info->netcount || info->port.tty->termios.c_cflag & CREAD)
 		usc_start_receiver(info);
 		
 	spin_unlock_irqrestore(&info->irq_spinlock,flags);
@@ -1908,14 +1908,14 @@
 	unsigned cflag;
 	int bits_per_char;
 
-	if (!info->port.tty || !info->port.tty->termios)
+	if (!info->port.tty)
 		return;
 		
 	if (debug_level >= DEBUG_LEVEL_INFO)
 		printk("%s(%d):mgsl_change_params(%s)\n",
 			 __FILE__,__LINE__, info->device_name );
 			 
-	cflag = info->port.tty->termios->c_cflag;
+	cflag = info->port.tty->termios.c_cflag;
 
 	/* if B0 rate (hangup) specified then negate DTR and RTS */
 	/* otherwise assert DTR and RTS */
@@ -2367,8 +2367,8 @@
 	
 	if (I_IXOFF(tty))
 		mgsl_send_xchar(tty, STOP_CHAR(tty));
- 
- 	if (tty->termios->c_cflag & CRTSCTS) {
+
+	if (tty->termios.c_cflag & CRTSCTS) {
 		spin_lock_irqsave(&info->irq_spinlock,flags);
 		info->serial_signals &= ~SerialSignal_RTS;
 	 	usc_set_serial_signals(info);
@@ -2401,8 +2401,8 @@
 		else
 			mgsl_send_xchar(tty, START_CHAR(tty));
 	}
-	
- 	if (tty->termios->c_cflag & CRTSCTS) {
+
+	if (tty->termios.c_cflag & CRTSCTS) {
 		spin_lock_irqsave(&info->irq_spinlock,flags);
 		info->serial_signals |= SerialSignal_RTS;
 	 	usc_set_serial_signals(info);
@@ -3045,7 +3045,7 @@
 
 	/* Handle transition to B0 status */
 	if (old_termios->c_cflag & CBAUD &&
-	    !(tty->termios->c_cflag & CBAUD)) {
+	    !(tty->termios.c_cflag & CBAUD)) {
 		info->serial_signals &= ~(SerialSignal_RTS + SerialSignal_DTR);
 		spin_lock_irqsave(&info->irq_spinlock,flags);
 	 	usc_set_serial_signals(info);
@@ -3054,9 +3054,9 @@
 	
 	/* Handle transition away from B0 status */
 	if (!(old_termios->c_cflag & CBAUD) &&
-	    tty->termios->c_cflag & CBAUD) {
+	    tty->termios.c_cflag & CBAUD) {
 		info->serial_signals |= SerialSignal_DTR;
- 		if (!(tty->termios->c_cflag & CRTSCTS) || 
+ 		if (!(tty->termios.c_cflag & CRTSCTS) || 
  		    !test_bit(TTY_THROTTLED, &tty->flags)) {
 			info->serial_signals |= SerialSignal_RTS;
  		}
@@ -3067,7 +3067,7 @@
 	
 	/* Handle turning off CRTSCTS */
 	if (old_termios->c_cflag & CRTSCTS &&
-	    !(tty->termios->c_cflag & CRTSCTS)) {
+	    !(tty->termios.c_cflag & CRTSCTS)) {
 		tty->hw_stopped = 0;
 		mgsl_start(tty);
 	}
@@ -3287,7 +3287,7 @@
 		return 0;
 	}
 
-	if (tty->termios->c_cflag & CLOCAL)
+	if (tty->termios.c_cflag & CLOCAL)
 		do_clocal = true;
 
 	/* Wait for carrier detect and the line to become
@@ -3313,7 +3313,7 @@
 	port->blocked_open++;
 	
 	while (1) {
-		if (tty->termios->c_cflag & CBAUD)
+		if (tty->termios.c_cflag & CBAUD)
 			tty_port_raise_dtr_rts(port);
 		
 		set_current_state(TASK_INTERRUPTIBLE);
@@ -3338,9 +3338,9 @@
 			printk("%s(%d):block_til_ready blocking on %s count=%d\n",
 				 __FILE__,__LINE__, tty->driver->name, port->count );
 				 
-		tty_unlock();
+		tty_unlock(tty);
 		schedule();
-		tty_lock();
+		tty_lock(tty);
 	}
 	
 	set_current_state(TASK_RUNNING);
@@ -3362,6 +3362,29 @@
 	
 }	/* end of block_til_ready() */
 
+static int mgsl_install(struct tty_driver *driver, struct tty_struct *tty)
+{
+	struct mgsl_struct *info;
+	int line = tty->index;
+
+	/* verify range of specified line number */
+	if (line >= mgsl_device_count) {
+		printk("%s(%d):mgsl_open with invalid line #%d.\n",
+			__FILE__, __LINE__, line);
+		return -ENODEV;
+	}
+
+	/* find the info structure for the specified line */
+	info = mgsl_device_list;
+	while (info && info->line != line)
+		info = info->next_device;
+	if (mgsl_paranoia_check(info, tty->name, "mgsl_open"))
+		return -ENODEV;
+	tty->driver_data = info;
+
+	return tty_port_install(&info->port, driver, tty);
+}
+
 /* mgsl_open()
  *
  *	Called when a port is opened.  Init and enable port.
@@ -3374,26 +3397,10 @@
  */
 static int mgsl_open(struct tty_struct *tty, struct file * filp)
 {
-	struct mgsl_struct	*info;
-	int 			retval, line;
+	struct mgsl_struct *info = tty->driver_data;
 	unsigned long flags;
+	int retval;
 
-	/* verify range of specified line number */	
-	line = tty->index;
-	if (line >= mgsl_device_count) {
-		printk("%s(%d):mgsl_open with invalid line #%d.\n",
-			__FILE__,__LINE__,line);
-		return -ENODEV;
-	}
-
-	/* find the info structure for the specified line */
-	info = mgsl_device_list;
-	while(info && info->line != line)
-		info = info->next_device;
-	if (mgsl_paranoia_check(info, tty->name, "mgsl_open"))
-		return -ENODEV;
-	
-	tty->driver_data = info;
 	info->port.tty = tty;
 		
 	if (debug_level >= DEBUG_LEVEL_INFO)
@@ -4297,6 +4304,7 @@
 }	/* end of mgsl_allocate_device()*/
 
 static const struct tty_operations mgsl_ops = {
+	.install = mgsl_install,
 	.open = mgsl_open,
 	.close = mgsl_close,
 	.write = mgsl_write,
diff --git a/drivers/tty/synclink_gt.c b/drivers/tty/synclink_gt.c
index aa1debf..b38e954 100644
--- a/drivers/tty/synclink_gt.c
+++ b/drivers/tty/synclink_gt.c
@@ -785,7 +785,7 @@
 
 	/* Handle transition to B0 status */
 	if (old_termios->c_cflag & CBAUD &&
-	    !(tty->termios->c_cflag & CBAUD)) {
+	    !(tty->termios.c_cflag & CBAUD)) {
 		info->signals &= ~(SerialSignal_RTS + SerialSignal_DTR);
 		spin_lock_irqsave(&info->lock,flags);
 		set_signals(info);
@@ -794,9 +794,9 @@
 
 	/* Handle transition away from B0 status */
 	if (!(old_termios->c_cflag & CBAUD) &&
-	    tty->termios->c_cflag & CBAUD) {
+	    tty->termios.c_cflag & CBAUD) {
 		info->signals |= SerialSignal_DTR;
- 		if (!(tty->termios->c_cflag & CRTSCTS) ||
+ 		if (!(tty->termios.c_cflag & CRTSCTS) ||
  		    !test_bit(TTY_THROTTLED, &tty->flags)) {
 			info->signals |= SerialSignal_RTS;
  		}
@@ -807,7 +807,7 @@
 
 	/* Handle turning off CRTSCTS */
 	if (old_termios->c_cflag & CRTSCTS &&
-	    !(tty->termios->c_cflag & CRTSCTS)) {
+	    !(tty->termios.c_cflag & CRTSCTS)) {
 		tty->hw_stopped = 0;
 		tx_release(tty);
 	}
@@ -1372,7 +1372,7 @@
 	DBGINFO(("%s throttle\n", info->device_name));
 	if (I_IXOFF(tty))
 		send_xchar(tty, STOP_CHAR(tty));
- 	if (tty->termios->c_cflag & CRTSCTS) {
+ 	if (tty->termios.c_cflag & CRTSCTS) {
 		spin_lock_irqsave(&info->lock,flags);
 		info->signals &= ~SerialSignal_RTS;
 	 	set_signals(info);
@@ -1397,7 +1397,7 @@
 		else
 			send_xchar(tty, START_CHAR(tty));
 	}
- 	if (tty->termios->c_cflag & CRTSCTS) {
+ 	if (tty->termios.c_cflag & CRTSCTS) {
 		spin_lock_irqsave(&info->lock,flags);
 		info->signals |= SerialSignal_RTS;
 	 	set_signals(info);
@@ -2053,7 +2053,7 @@
 	wake_up_interruptible(&info->event_wait_q);
 	info->pending_bh |= BH_STATUS;
 
-	if (info->port.flags & ASYNC_CTS_FLOW) {
+	if (tty_port_cts_enabled(&info->port)) {
 		if (info->port.tty) {
 			if (info->port.tty->hw_stopped) {
 				if (info->signals & SerialSignal_CTS) {
@@ -2493,7 +2493,7 @@
 
 	slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
 
- 	if (!info->port.tty || info->port.tty->termios->c_cflag & HUPCL) {
+ 	if (!info->port.tty || info->port.tty->termios.c_cflag & HUPCL) {
  		info->signals &= ~(SerialSignal_DTR + SerialSignal_RTS);
 		set_signals(info);
 	}
@@ -2534,7 +2534,7 @@
 	get_signals(info);
 
 	if (info->netcount ||
-	    (info->port.tty && info->port.tty->termios->c_cflag & CREAD))
+	    (info->port.tty && info->port.tty->termios.c_cflag & CREAD))
 		rx_start(info);
 
 	spin_unlock_irqrestore(&info->lock,flags);
@@ -2548,11 +2548,11 @@
 	unsigned cflag;
 	int bits_per_char;
 
-	if (!info->port.tty || !info->port.tty->termios)
+	if (!info->port.tty)
 		return;
 	DBGINFO(("%s change_params\n", info->device_name));
 
-	cflag = info->port.tty->termios->c_cflag;
+	cflag = info->port.tty->termios.c_cflag;
 
 	/* if B0 rate (hangup) specified then negate DTR and RTS */
 	/* otherwise assert DTR and RTS */
@@ -3292,7 +3292,7 @@
 		return 0;
 	}
 
-	if (tty->termios->c_cflag & CLOCAL)
+	if (tty->termios.c_cflag & CLOCAL)
 		do_clocal = true;
 
 	/* Wait for carrier detect and the line to become
@@ -3314,7 +3314,7 @@
 	port->blocked_open++;
 
 	while (1) {
-		if ((tty->termios->c_cflag & CBAUD))
+		if ((tty->termios.c_cflag & CBAUD))
 			tty_port_raise_dtr_rts(port);
 
 		set_current_state(TASK_INTERRUPTIBLE);
@@ -3336,9 +3336,9 @@
 		}
 
 		DBGINFO(("%s block_til_ready wait\n", tty->driver->name));
-		tty_unlock();
+		tty_unlock(tty);
 		schedule();
-		tty_lock();
+		tty_lock(tty);
 	}
 
 	set_current_state(TASK_RUNNING);
@@ -3689,8 +3689,11 @@
 		}
 	}
 
-	for (i=0; i < port_count; ++i)
-		tty_register_device(serial_driver, port_array[i]->line, &(port_array[i]->pdev->dev));
+	for (i = 0; i < port_count; ++i) {
+		struct slgt_info *info = port_array[i];
+		tty_port_register_device(&info->port, serial_driver, info->line,
+				&info->pdev->dev);
+	}
 }
 
 static int __devinit init_one(struct pci_dev *dev,
diff --git a/drivers/tty/synclinkmp.c b/drivers/tty/synclinkmp.c
index a3dddc1..f17d9f3 100644
--- a/drivers/tty/synclinkmp.c
+++ b/drivers/tty/synclinkmp.c
@@ -711,15 +711,11 @@
 
 /* tty callbacks */
 
-/* Called when a port is opened.  Init and enable port.
- */
-static int open(struct tty_struct *tty, struct file *filp)
+static int install(struct tty_driver *driver, struct tty_struct *tty)
 {
 	SLMP_INFO *info;
-	int retval, line;
-	unsigned long flags;
+	int line = tty->index;
 
-	line = tty->index;
 	if (line >= synclinkmp_device_count) {
 		printk("%s(%d): open with invalid line #%d.\n",
 			__FILE__,__LINE__,line);
@@ -727,17 +723,30 @@
 	}
 
 	info = synclinkmp_device_list;
-	while(info && info->line != line)
+	while (info && info->line != line)
 		info = info->next_device;
 	if (sanity_check(info, tty->name, "open"))
 		return -ENODEV;
-	if ( info->init_error ) {
+	if (info->init_error) {
 		printk("%s(%d):%s device is not allocated, init error=%d\n",
-			__FILE__,__LINE__,info->device_name,info->init_error);
+			__FILE__, __LINE__, info->device_name,
+			info->init_error);
 		return -ENODEV;
 	}
 
 	tty->driver_data = info;
+
+	return tty_port_install(&info->port, driver, tty);
+}
+
+/* Called when a port is opened.  Init and enable port.
+ */
+static int open(struct tty_struct *tty, struct file *filp)
+{
+	SLMP_INFO *info = tty->driver_data;
+	unsigned long flags;
+	int retval;
+
 	info->port.tty = tty;
 
 	if (debug_level >= DEBUG_LEVEL_INFO)
@@ -873,7 +882,7 @@
 
 	/* Handle transition to B0 status */
 	if (old_termios->c_cflag & CBAUD &&
-	    !(tty->termios->c_cflag & CBAUD)) {
+	    !(tty->termios.c_cflag & CBAUD)) {
 		info->serial_signals &= ~(SerialSignal_RTS + SerialSignal_DTR);
 		spin_lock_irqsave(&info->lock,flags);
 	 	set_signals(info);
@@ -882,9 +891,9 @@
 
 	/* Handle transition away from B0 status */
 	if (!(old_termios->c_cflag & CBAUD) &&
-	    tty->termios->c_cflag & CBAUD) {
+	    tty->termios.c_cflag & CBAUD) {
 		info->serial_signals |= SerialSignal_DTR;
- 		if (!(tty->termios->c_cflag & CRTSCTS) ||
+ 		if (!(tty->termios.c_cflag & CRTSCTS) ||
  		    !test_bit(TTY_THROTTLED, &tty->flags)) {
 			info->serial_signals |= SerialSignal_RTS;
  		}
@@ -895,7 +904,7 @@
 
 	/* Handle turning off CRTSCTS */
 	if (old_termios->c_cflag & CRTSCTS &&
-	    !(tty->termios->c_cflag & CRTSCTS)) {
+	    !(tty->termios.c_cflag & CRTSCTS)) {
 		tty->hw_stopped = 0;
 		tx_release(tty);
 	}
@@ -1473,7 +1482,7 @@
 	if (I_IXOFF(tty))
 		send_xchar(tty, STOP_CHAR(tty));
 
- 	if (tty->termios->c_cflag & CRTSCTS) {
+ 	if (tty->termios.c_cflag & CRTSCTS) {
 		spin_lock_irqsave(&info->lock,flags);
 		info->serial_signals &= ~SerialSignal_RTS;
 	 	set_signals(info);
@@ -1502,7 +1511,7 @@
 			send_xchar(tty, START_CHAR(tty));
 	}
 
- 	if (tty->termios->c_cflag & CRTSCTS) {
+ 	if (tty->termios.c_cflag & CRTSCTS) {
 		spin_lock_irqsave(&info->lock,flags);
 		info->serial_signals |= SerialSignal_RTS;
 	 	set_signals(info);
@@ -2491,7 +2500,7 @@
 			}
 		}
 
-		if ( (info->port.flags & ASYNC_CTS_FLOW) &&
+		if (tty_port_cts_enabled(&info->port) &&
 		     (status & MISCSTATUS_CTS_LATCHED) ) {
 			if ( info->port.tty ) {
 				if (info->port.tty->hw_stopped) {
@@ -2708,7 +2717,7 @@
 
 	reset_port(info);
 
- 	if (!info->port.tty || info->port.tty->termios->c_cflag & HUPCL) {
+ 	if (!info->port.tty || info->port.tty->termios.c_cflag & HUPCL) {
  		info->serial_signals &= ~(SerialSignal_DTR + SerialSignal_RTS);
 		set_signals(info);
 	}
@@ -2749,7 +2758,7 @@
 
 	get_signals(info);
 
-	if (info->netcount || (info->port.tty && info->port.tty->termios->c_cflag & CREAD) )
+	if (info->netcount || (info->port.tty && info->port.tty->termios.c_cflag & CREAD) )
 		rx_start(info);
 
 	spin_unlock_irqrestore(&info->lock,flags);
@@ -2762,14 +2771,14 @@
 	unsigned cflag;
 	int bits_per_char;
 
-	if (!info->port.tty || !info->port.tty->termios)
+	if (!info->port.tty)
 		return;
 
 	if (debug_level >= DEBUG_LEVEL_INFO)
 		printk("%s(%d):%s change_params()\n",
 			 __FILE__,__LINE__, info->device_name );
 
-	cflag = info->port.tty->termios->c_cflag;
+	cflag = info->port.tty->termios.c_cflag;
 
 	/* if B0 rate (hangup) specified then negate DTR and RTS */
 	/* otherwise assert DTR and RTS */
@@ -3306,7 +3315,7 @@
 		return 0;
 	}
 
-	if (tty->termios->c_cflag & CLOCAL)
+	if (tty->termios.c_cflag & CLOCAL)
 		do_clocal = true;
 
 	/* Wait for carrier detect and the line to become
@@ -3332,7 +3341,7 @@
 	port->blocked_open++;
 
 	while (1) {
-		if (tty->termios->c_cflag & CBAUD)
+		if (tty->termios.c_cflag & CBAUD)
 			tty_port_raise_dtr_rts(port);
 
 		set_current_state(TASK_INTERRUPTIBLE);
@@ -3357,9 +3366,9 @@
 			printk("%s(%d):%s block_til_ready() count=%d\n",
 				 __FILE__,__LINE__, tty->driver->name, port->count );
 
-		tty_unlock();
+		tty_unlock(tty);
 		schedule();
-		tty_lock();
+		tty_lock(tty);
 	}
 
 	set_current_state(TASK_RUNNING);
@@ -3881,6 +3890,7 @@
 }
 
 static const struct tty_operations ops = {
+	.install = install,
 	.open = open,
 	.close = close,
 	.write = write,
diff --git a/drivers/tty/tty_io.c b/drivers/tty/tty_io.c
index b425c79..8a5a8b0 100644
--- a/drivers/tty/tty_io.c
+++ b/drivers/tty/tty_io.c
@@ -181,10 +181,13 @@
 
 void free_tty_struct(struct tty_struct *tty)
 {
+	if (!tty)
+		return;
 	if (tty->dev)
 		put_device(tty->dev);
 	kfree(tty->write_buf);
 	tty_buffer_free_all(tty);
+	tty->magic = 0xDEADDEAD;
 	kfree(tty);
 }
 
@@ -573,7 +576,7 @@
 	}
 	spin_unlock(&redirect_lock);
 
-	tty_lock();
+	tty_lock(tty);
 
 	/* some functions below drop BTM, so we need this bit */
 	set_bit(TTY_HUPPING, &tty->flags);
@@ -666,7 +669,7 @@
 	clear_bit(TTY_HUPPING, &tty->flags);
 	tty_ldisc_enable(tty);
 
-	tty_unlock();
+	tty_unlock(tty);
 
 	if (f)
 		fput(f);
@@ -1103,12 +1106,12 @@
 {
 	if (tty) {
 		mutex_lock(&tty->atomic_write_lock);
-		tty_lock();
+		tty_lock(tty);
 		if (tty->ops->write && !test_bit(TTY_CLOSING, &tty->flags)) {
-			tty_unlock();
+			tty_unlock(tty);
 			tty->ops->write(tty, msg, strlen(msg));
 		} else
-			tty_unlock();
+			tty_unlock(tty);
 		tty_write_unlock(tty);
 	}
 	return;
@@ -1213,7 +1216,10 @@
  */
 static void tty_line_name(struct tty_driver *driver, int index, char *p)
 {
-	sprintf(p, "%s%d", driver->name, index + driver->name_base);
+	if (driver->flags & TTY_DRIVER_UNNUMBERED_NODE)
+		strcpy(p, driver->name);
+	else
+		sprintf(p, "%s%d", driver->name, index + driver->name_base);
 }
 
 /**
@@ -1249,21 +1255,19 @@
 	struct ktermios *tp;
 	int idx = tty->index;
 
-	tp = tty->driver->termios[idx];
-	if (tp == NULL) {
-		tp = kzalloc(sizeof(struct ktermios[2]), GFP_KERNEL);
-		if (tp == NULL)
-			return -ENOMEM;
-		memcpy(tp, &tty->driver->init_termios,
-						sizeof(struct ktermios));
-		tty->driver->termios[idx] = tp;
+	if (tty->driver->flags & TTY_DRIVER_RESET_TERMIOS)
+		tty->termios = tty->driver->init_termios;
+	else {
+		/* Check for lazy saved data */
+		tp = tty->driver->termios[idx];
+		if (tp != NULL)
+			tty->termios = *tp;
+		else
+			tty->termios = tty->driver->init_termios;
 	}
-	tty->termios = tp;
-	tty->termios_locked = tp + 1;
-
 	/* Compatibility until drivers always set this */
-	tty->termios->c_ispeed = tty_termios_input_baud_rate(tty->termios);
-	tty->termios->c_ospeed = tty_termios_baud_rate(tty->termios);
+	tty->termios.c_ispeed = tty_termios_input_baud_rate(&tty->termios);
+	tty->termios.c_ospeed = tty_termios_baud_rate(&tty->termios);
 	return 0;
 }
 EXPORT_SYMBOL_GPL(tty_init_termios);
@@ -1403,10 +1407,18 @@
 	}
 	initialize_tty_struct(tty, driver, idx);
 
+	tty_lock(tty);
 	retval = tty_driver_install_tty(driver, tty);
 	if (retval < 0)
 		goto err_deinit_tty;
 
+	if (!tty->port)
+		tty->port = driver->ports[idx];
+
+	WARN_RATELIMIT(!tty->port,
+			"%s: %s driver does not set tty->port. This will crash the kernel later. Fix the driver!\n",
+			__func__, tty->driver->name);
+
 	/*
 	 * Structures all installed ... call the ldisc open routines.
 	 * If we fail here just call release_tty to clean up.  No need
@@ -1415,9 +1427,11 @@
 	retval = tty_ldisc_setup(tty, tty->link);
 	if (retval)
 		goto err_release_tty;
+	/* Return the tty locked so that it cannot vanish under the caller */
 	return tty;
 
 err_deinit_tty:
+	tty_unlock(tty);
 	deinitialize_tty_struct(tty);
 	free_tty_struct(tty);
 err_module_put:
@@ -1426,6 +1440,7 @@
 
 	/* call the tty release_tty routine to clean out this slot */
 err_release_tty:
+	tty_unlock(tty);
 	printk_ratelimited(KERN_INFO "tty_init_dev: ldisc open failed, "
 				 "clearing slot %d\n", idx);
 	release_tty(tty, idx);
@@ -1436,22 +1451,25 @@
 {
 	struct ktermios *tp;
 	int idx = tty->index;
-	/* Kill this flag and push into drivers for locking etc */
-	if (tty->driver->flags & TTY_DRIVER_RESET_TERMIOS) {
-		/* FIXME: Locking on ->termios array */
-		tp = tty->termios;
-		tty->driver->termios[idx] = NULL;
-		kfree(tp);
+
+	/* If the port is going to reset then it has no termios to save */
+	if (tty->driver->flags & TTY_DRIVER_RESET_TERMIOS)
+		return;
+
+	/* Stash the termios data */
+	tp = tty->driver->termios[idx];
+	if (tp == NULL) {
+		tp = kmalloc(sizeof(struct ktermios), GFP_KERNEL);
+		if (tp == NULL) {
+			pr_warn("tty: no memory to save termios state.\n");
+			return;
+		}
+		tty->driver->termios[idx] = tp;
 	}
+	*tp = tty->termios;
 }
 EXPORT_SYMBOL(tty_free_termios);
 
-void tty_shutdown(struct tty_struct *tty)
-{
-	tty_driver_remove_tty(tty->driver, tty);
-	tty_free_termios(tty);
-}
-EXPORT_SYMBOL(tty_shutdown);
 
 /**
  *	release_one_tty		-	release tty structure memory
@@ -1462,7 +1480,6 @@
  *	in use. It also gets called when setup of a device fails.
  *
  *	Locking:
- *		tty_mutex - sometimes only
  *		takes the file list lock internally when working on the list
  *	of ttys that the driver keeps.
  *
@@ -1495,11 +1512,6 @@
 {
 	struct tty_struct *tty = container_of(kref, struct tty_struct, kref);
 
-	if (tty->ops->shutdown)
-		tty->ops->shutdown(tty);
-	else
-		tty_shutdown(tty);
-
 	/* The hangup queue is now free so we can reuse it rather than
 	   waste a chunk of memory for each port */
 	INIT_WORK(&tty->hangup_work, release_one_tty);
@@ -1528,16 +1540,20 @@
  *	and decrement the refcount of the backing module.
  *
  *	Locking:
- *		tty_mutex - sometimes only
+ *		tty_mutex
  *		takes the file list lock internally when working on the list
  *	of ttys that the driver keeps.
- *		FIXME: should we require tty_mutex is held here ??
  *
  */
 static void release_tty(struct tty_struct *tty, int idx)
 {
 	/* This should always be true but check for the moment */
 	WARN_ON(tty->index != idx);
+	WARN_ON(!mutex_is_locked(&tty_mutex));
+	if (tty->ops->shutdown)
+		tty->ops->shutdown(tty);
+	tty_free_termios(tty);
+	tty_driver_remove_tty(tty->driver, tty);
 
 	if (tty->link)
 		tty_kref_put(tty->link);
@@ -1572,22 +1588,12 @@
 				__func__, idx, tty->name);
 		return -1;
 	}
-	if (tty->termios != tty->driver->termios[idx]) {
-		printk(KERN_DEBUG "%s: driver.termios[%d] not termios for (%s)\n",
-				__func__, idx, tty->name);
-		return -1;
-	}
 	if (tty->driver->other) {
 		if (o_tty != tty->driver->other->ttys[idx]) {
 			printk(KERN_DEBUG "%s: other->table[%d] not o_tty for (%s)\n",
 					__func__, idx, tty->name);
 			return -1;
 		}
-		if (o_tty->termios != tty->driver->other->termios[idx]) {
-			printk(KERN_DEBUG "%s: other->termios[%d] not o_termios for (%s)\n",
-					__func__, idx, tty->name);
-			return -1;
-		}
 		if (o_tty->link != tty) {
 			printk(KERN_DEBUG "%s: bad pty pointers\n", __func__);
 			return -1;
@@ -1628,7 +1634,7 @@
 	if (tty_paranoia_check(tty, inode, __func__))
 		return 0;
 
-	tty_lock();
+	tty_lock(tty);
 	check_tty_count(tty, __func__);
 
 	__tty_fasync(-1, filp, 0);
@@ -1637,10 +1643,11 @@
 	pty_master = (tty->driver->type == TTY_DRIVER_TYPE_PTY &&
 		      tty->driver->subtype == PTY_TYPE_MASTER);
 	devpts = (tty->driver->flags & TTY_DRIVER_DEVPTS_MEM) != 0;
+	/* Review: parallel close */
 	o_tty = tty->link;
 
 	if (tty_release_checks(tty, o_tty, idx)) {
-		tty_unlock();
+		tty_unlock(tty);
 		return 0;
 	}
 
@@ -1652,7 +1659,7 @@
 	if (tty->ops->close)
 		tty->ops->close(tty, filp);
 
-	tty_unlock();
+	tty_unlock(tty);
 	/*
 	 * Sanity check: if tty->count is going to zero, there shouldn't be
 	 * any waiters on tty->read_wait or tty->write_wait.  We test the
@@ -1675,7 +1682,7 @@
 		   opens on /dev/tty */
 
 		mutex_lock(&tty_mutex);
-		tty_lock();
+		tty_lock_pair(tty, o_tty);
 		tty_closing = tty->count <= 1;
 		o_tty_closing = o_tty &&
 			(o_tty->count <= (pty_master ? 1 : 0));
@@ -1706,7 +1713,7 @@
 
 		printk(KERN_WARNING "%s: %s: read/write wait queue active!\n",
 				__func__, tty_name(tty, buf));
-		tty_unlock();
+		tty_unlock_pair(tty, o_tty);
 		mutex_unlock(&tty_mutex);
 		schedule();
 	}
@@ -1715,6 +1722,9 @@
 	 * The closing flags are now consistent with the open counts on
 	 * both sides, and we've completed the last operation that could
 	 * block, so it's safe to proceed with closing.
+	 *
+	 * We must *not* drop the tty_mutex until we ensure that a further
+	 * entry into tty_open can not pick up this tty.
 	 */
 	if (pty_master) {
 		if (--o_tty->count < 0) {
@@ -1766,12 +1776,13 @@
 	}
 
 	mutex_unlock(&tty_mutex);
+	tty_unlock_pair(tty, o_tty);
+	/* At this point the TTY_CLOSING flag should ensure a dead tty
+	   cannot be re-opened by a racing opener */
 
 	/* check whether both sides are closing ... */
-	if (!tty_closing || (o_tty && !o_tty_closing)) {
-		tty_unlock();
+	if (!tty_closing || (o_tty && !o_tty_closing))
 		return 0;
-	}
 
 #ifdef TTY_DEBUG_HANGUP
 	printk(KERN_DEBUG "%s: freeing tty structure...\n", __func__);
@@ -1782,14 +1793,17 @@
 	tty_ldisc_release(tty, o_tty);
 	/*
 	 * The release_tty function takes care of the details of clearing
-	 * the slots and preserving the termios structure.
+	 * the slots and preserving the termios structure. The tty_unlock_pair
+	 * should be safe as we keep a kref while the tty is locked (so the
+	 * unlock never unlocks a freed tty).
 	 */
+	mutex_lock(&tty_mutex);
 	release_tty(tty, idx);
+	mutex_unlock(&tty_mutex);
 
 	/* Make this pty number available for reallocation */
 	if (devpts)
 		devpts_kill_index(inode, idx);
-	tty_unlock();
 	return 0;
 }
 
@@ -1893,6 +1907,9 @@
  *	Locking: tty_mutex protects tty, tty_lookup_driver and tty_init_dev.
  *		 tty->count should protect the rest.
  *		 ->siglock protects ->signal/->sighand
+ *
+ *	Note: the tty_unlock/lock cases without a ref are only safe due to
+ *	tty_mutex
  */
 
 static int tty_open(struct inode *inode, struct file *filp)
@@ -1916,8 +1933,7 @@
 	retval = 0;
 
 	mutex_lock(&tty_mutex);
-	tty_lock();
-
+	/* This is protected by the tty_mutex */
 	tty = tty_open_current_tty(device, filp);
 	if (IS_ERR(tty)) {
 		retval = PTR_ERR(tty);
@@ -1938,17 +1954,19 @@
 	}
 
 	if (tty) {
+		tty_lock(tty);
 		retval = tty_reopen(tty);
-		if (retval)
+		if (retval < 0) {
+			tty_unlock(tty);
 			tty = ERR_PTR(retval);
-	} else
+		}
+	} else	/* Returns with the tty_lock held for now */
 		tty = tty_init_dev(driver, index);
 
 	mutex_unlock(&tty_mutex);
 	if (driver)
 		tty_driver_kref_put(driver);
 	if (IS_ERR(tty)) {
-		tty_unlock();
 		retval = PTR_ERR(tty);
 		goto err_file;
 	}
@@ -1977,7 +1995,7 @@
 		printk(KERN_DEBUG "%s: error %d in opening %s...\n", __func__,
 				retval, tty->name);
 #endif
-		tty_unlock(); /* need to call tty_release without BTM */
+		tty_unlock(tty); /* need to call tty_release without BTM */
 		tty_release(inode, filp);
 		if (retval != -ERESTARTSYS)
 			return retval;
@@ -1989,17 +2007,15 @@
 		/*
 		 * Need to reset f_op in case a hangup happened.
 		 */
-		tty_lock();
 		if (filp->f_op == &hung_up_tty_fops)
 			filp->f_op = &tty_fops;
-		tty_unlock();
 		goto retry_open;
 	}
-	tty_unlock();
+	tty_unlock(tty);
 
 
 	mutex_lock(&tty_mutex);
-	tty_lock();
+	tty_lock(tty);
 	spin_lock_irq(&current->sighand->siglock);
 	if (!noctty &&
 	    current->signal->leader &&
@@ -2007,11 +2023,10 @@
 	    tty->session == NULL)
 		__proc_set_tty(current, tty);
 	spin_unlock_irq(&current->sighand->siglock);
-	tty_unlock();
+	tty_unlock(tty);
 	mutex_unlock(&tty_mutex);
 	return 0;
 err_unlock:
-	tty_unlock();
 	mutex_unlock(&tty_mutex);
 	/* after locks to avoid deadlock */
 	if (!IS_ERR_OR_NULL(driver))
@@ -2094,10 +2109,13 @@
 
 static int tty_fasync(int fd, struct file *filp, int on)
 {
+	struct tty_struct *tty = file_tty(filp);
 	int retval;
-	tty_lock();
+
+	tty_lock(tty);
 	retval = __tty_fasync(fd, filp, on);
-	tty_unlock();
+	tty_unlock(tty);
+
 	return retval;
 }
 
@@ -2756,7 +2774,7 @@
 	if (ld->ops->ioctl) {
 		retval = ld->ops->ioctl(tty, file, cmd, arg);
 		if (retval == -ENOIOCTLCMD)
-			retval = -EINVAL;
+			retval = -ENOTTY;
 	}
 	tty_ldisc_deref(ld);
 	return retval;
@@ -2934,6 +2952,7 @@
 	tty->pgrp = NULL;
 	tty->overrun_time = jiffies;
 	tty_buffer_init(tty);
+	mutex_init(&tty->legacy_mutex);
 	mutex_init(&tty->termios_mutex);
 	mutex_init(&tty->ldisc_mutex);
 	init_waitqueue_head(&tty->write_wait);
@@ -2991,6 +3010,15 @@
 
 struct class *tty_class;
 
+static int tty_cdev_add(struct tty_driver *driver, dev_t dev,
+		unsigned int index, unsigned int count)
+{
+	/* init here, since reused cdevs cause crashes */
+	cdev_init(&driver->cdevs[index], &tty_fops);
+	driver->cdevs[index].owner = driver->owner;
+	return cdev_add(&driver->cdevs[index], dev, count);
+}
+
 /**
  *	tty_register_device - register a tty device
  *	@driver: the tty driver that describes the tty device
@@ -3013,8 +3041,46 @@
 struct device *tty_register_device(struct tty_driver *driver, unsigned index,
 				   struct device *device)
 {
+	return tty_register_device_attr(driver, index, device, NULL, NULL);
+}
+EXPORT_SYMBOL(tty_register_device);
+
+static void tty_device_create_release(struct device *dev)
+{
+	pr_debug("device: '%s': %s\n", dev_name(dev), __func__);
+	kfree(dev);
+}
+
+/**
+ *	tty_register_device_attr - register a tty device
+ *	@driver: the tty driver that describes the tty device
+ *	@index: the index in the tty driver for this tty device
+ *	@device: a struct device that is associated with this tty device.
+ *		This field is optional, if there is no known struct device
+ *		for this tty device it can be set to NULL safely.
+ *	@drvdata: Driver data to be set to device.
+ *	@attr_grp: Attribute group to be set on device.
+ *
+ *	Returns a pointer to the struct device for this tty device
+ *	(or ERR_PTR(-EFOO) on error).
+ *
+ *	This call is required to be made to register an individual tty device
+ *	if the tty driver's flags have the TTY_DRIVER_DYNAMIC_DEV bit set.  If
+ *	that bit is not set, this function should not be called by a tty
+ *	driver.
+ *
+ *	Locking: ??
+ */
+struct device *tty_register_device_attr(struct tty_driver *driver,
+				   unsigned index, struct device *device,
+				   void *drvdata,
+				   const struct attribute_group **attr_grp)
+{
 	char name[64];
-	dev_t dev = MKDEV(driver->major, driver->minor_start) + index;
+	dev_t devt = MKDEV(driver->major, driver->minor_start) + index;
+	struct device *dev = NULL;
+	int retval = -ENODEV;
+	bool cdev = false;
 
 	if (index >= driver->num) {
 		printk(KERN_ERR "Attempt to register invalid tty line number "
@@ -3027,9 +3093,40 @@
 	else
 		tty_line_name(driver, index, name);
 
-	return device_create(tty_class, device, dev, NULL, name);
+	if (!(driver->flags & TTY_DRIVER_DYNAMIC_ALLOC)) {
+		retval = tty_cdev_add(driver, devt, index, 1);
+		if (retval)
+			goto error;
+		cdev = true;
+	}
+
+	dev = kzalloc(sizeof(*dev), GFP_KERNEL);
+	if (!dev) {
+		retval = -ENOMEM;
+		goto error;
+	}
+
+	dev->devt = devt;
+	dev->class = tty_class;
+	dev->parent = device;
+	dev->release = tty_device_create_release;
+	dev_set_name(dev, "%s", name);
+	dev->groups = attr_grp;
+	dev_set_drvdata(dev, drvdata);
+
+	retval = device_register(dev);
+	if (retval)
+		goto error;
+
+	return dev;
+
+error:
+	put_device(dev);
+	if (cdev)
+		cdev_del(&driver->cdevs[index]);
+	return ERR_PTR(retval);
 }
-EXPORT_SYMBOL(tty_register_device);
+EXPORT_SYMBOL_GPL(tty_register_device_attr);
 
 /**
  * 	tty_unregister_device - unregister a tty device
@@ -3046,31 +3143,82 @@
 {
 	device_destroy(tty_class,
 		MKDEV(driver->major, driver->minor_start) + index);
+	if (!(driver->flags & TTY_DRIVER_DYNAMIC_ALLOC))
+		cdev_del(&driver->cdevs[index]);
 }
 EXPORT_SYMBOL(tty_unregister_device);
 
-struct tty_driver *__alloc_tty_driver(int lines, struct module *owner)
+/**
+ * __tty_alloc_driver -- allocate tty driver
+ * @lines: count of lines this driver can handle at most
+ * @owner: module which is repsonsible for this driver
+ * @flags: some of TTY_DRIVER_* flags, will be set in driver->flags
+ *
+ * This should not be called directly, some of the provided macros should be
+ * used instead. Use IS_ERR and friends on @retval.
+ */
+struct tty_driver *__tty_alloc_driver(unsigned int lines, struct module *owner,
+		unsigned long flags)
 {
 	struct tty_driver *driver;
+	unsigned int cdevs = 1;
+	int err;
+
+	if (!lines || (flags & TTY_DRIVER_UNNUMBERED_NODE && lines > 1))
+		return ERR_PTR(-EINVAL);
 
 	driver = kzalloc(sizeof(struct tty_driver), GFP_KERNEL);
-	if (driver) {
-		kref_init(&driver->kref);
-		driver->magic = TTY_DRIVER_MAGIC;
-		driver->num = lines;
-		driver->owner = owner;
-		/* later we'll move allocation of tables here */
+	if (!driver)
+		return ERR_PTR(-ENOMEM);
+
+	kref_init(&driver->kref);
+	driver->magic = TTY_DRIVER_MAGIC;
+	driver->num = lines;
+	driver->owner = owner;
+	driver->flags = flags;
+
+	if (!(flags & TTY_DRIVER_DEVPTS_MEM)) {
+		driver->ttys = kcalloc(lines, sizeof(*driver->ttys),
+				GFP_KERNEL);
+		driver->termios = kcalloc(lines, sizeof(*driver->termios),
+				GFP_KERNEL);
+		if (!driver->ttys || !driver->termios) {
+			err = -ENOMEM;
+			goto err_free_all;
+		}
 	}
+
+	if (!(flags & TTY_DRIVER_DYNAMIC_ALLOC)) {
+		driver->ports = kcalloc(lines, sizeof(*driver->ports),
+				GFP_KERNEL);
+		if (!driver->ports) {
+			err = -ENOMEM;
+			goto err_free_all;
+		}
+		cdevs = lines;
+	}
+
+	driver->cdevs = kcalloc(cdevs, sizeof(*driver->cdevs), GFP_KERNEL);
+	if (!driver->cdevs) {
+		err = -ENOMEM;
+		goto err_free_all;
+	}
+
 	return driver;
+err_free_all:
+	kfree(driver->ports);
+	kfree(driver->ttys);
+	kfree(driver->termios);
+	kfree(driver);
+	return ERR_PTR(err);
 }
-EXPORT_SYMBOL(__alloc_tty_driver);
+EXPORT_SYMBOL(__tty_alloc_driver);
 
 static void destruct_tty_driver(struct kref *kref)
 {
 	struct tty_driver *driver = container_of(kref, struct tty_driver, kref);
 	int i;
 	struct ktermios *tp;
-	void *p;
 
 	if (driver->flags & TTY_DRIVER_INSTALLED) {
 		/*
@@ -3087,13 +3235,14 @@
 			if (!(driver->flags & TTY_DRIVER_DYNAMIC_DEV))
 				tty_unregister_device(driver, i);
 		}
-		p = driver->ttys;
 		proc_tty_unregister_driver(driver);
-		driver->ttys = NULL;
-		driver->termios = NULL;
-		kfree(p);
-		cdev_del(&driver->cdev);
+		if (driver->flags & TTY_DRIVER_DYNAMIC_ALLOC)
+			cdev_del(&driver->cdevs[0]);
 	}
+	kfree(driver->cdevs);
+	kfree(driver->ports);
+	kfree(driver->termios);
+	kfree(driver->ttys);
 	kfree(driver);
 }
 
@@ -3124,15 +3273,8 @@
 	int error;
 	int i;
 	dev_t dev;
-	void **p = NULL;
 	struct device *d;
 
-	if (!(driver->flags & TTY_DRIVER_DEVPTS_MEM) && driver->num) {
-		p = kzalloc(driver->num * 2 * sizeof(void *), GFP_KERNEL);
-		if (!p)
-			return -ENOMEM;
-	}
-
 	if (!driver->major) {
 		error = alloc_chrdev_region(&dev, driver->minor_start,
 						driver->num, driver->name);
@@ -3144,28 +3286,13 @@
 		dev = MKDEV(driver->major, driver->minor_start);
 		error = register_chrdev_region(dev, driver->num, driver->name);
 	}
-	if (error < 0) {
-		kfree(p);
-		return error;
-	}
+	if (error < 0)
+		goto err;
 
-	if (p) {
-		driver->ttys = (struct tty_struct **)p;
-		driver->termios = (struct ktermios **)(p + driver->num);
-	} else {
-		driver->ttys = NULL;
-		driver->termios = NULL;
-	}
-
-	cdev_init(&driver->cdev, &tty_fops);
-	driver->cdev.owner = driver->owner;
-	error = cdev_add(&driver->cdev, dev, driver->num);
-	if (error) {
-		unregister_chrdev_region(dev, driver->num);
-		driver->ttys = NULL;
-		driver->termios = NULL;
-		kfree(p);
-		return error;
+	if (driver->flags & TTY_DRIVER_DYNAMIC_ALLOC) {
+		error = tty_cdev_add(driver, dev, 0, driver->num);
+		if (error)
+			goto err_unreg_char;
 	}
 
 	mutex_lock(&tty_mutex);
@@ -3177,7 +3304,7 @@
 			d = tty_register_device(driver, i, NULL);
 			if (IS_ERR(d)) {
 				error = PTR_ERR(d);
-				goto err;
+				goto err_unreg_devs;
 			}
 		}
 	}
@@ -3185,7 +3312,7 @@
 	driver->flags |= TTY_DRIVER_INSTALLED;
 	return 0;
 
-err:
+err_unreg_devs:
 	for (i--; i >= 0; i--)
 		tty_unregister_device(driver, i);
 
@@ -3193,13 +3320,11 @@
 	list_del(&driver->tty_drivers);
 	mutex_unlock(&tty_mutex);
 
+err_unreg_char:
 	unregister_chrdev_region(dev, driver->num);
-	driver->ttys = NULL;
-	driver->termios = NULL;
-	kfree(p);
+err:
 	return error;
 }
-
 EXPORT_SYMBOL(tty_register_driver);
 
 /*
diff --git a/drivers/tty/tty_ioctl.c b/drivers/tty/tty_ioctl.c
index a1b9a2f..12b1fa0 100644
--- a/drivers/tty/tty_ioctl.c
+++ b/drivers/tty/tty_ioctl.c
@@ -410,7 +410,7 @@
 
 void tty_encode_baud_rate(struct tty_struct *tty, speed_t ibaud, speed_t obaud)
 {
-	tty_termios_encode_baud_rate(tty->termios, ibaud, obaud);
+	tty_termios_encode_baud_rate(&tty->termios, ibaud, obaud);
 }
 EXPORT_SYMBOL_GPL(tty_encode_baud_rate);
 
@@ -427,7 +427,7 @@
 
 speed_t tty_get_baud_rate(struct tty_struct *tty)
 {
-	speed_t baud = tty_termios_baud_rate(tty->termios);
+	speed_t baud = tty_termios_baud_rate(&tty->termios);
 
 	if (baud == 38400 && tty->alt_speed) {
 		if (!tty->warned) {
@@ -509,14 +509,14 @@
 	/* FIXME: we need to decide on some locking/ordering semantics
 	   for the set_termios notification eventually */
 	mutex_lock(&tty->termios_mutex);
-	old_termios = *tty->termios;
-	*tty->termios = *new_termios;
-	unset_locked_termios(tty->termios, &old_termios, tty->termios_locked);
+	old_termios = tty->termios;
+	tty->termios = *new_termios;
+	unset_locked_termios(&tty->termios, &old_termios, &tty->termios_locked);
 
 	/* See if packet mode change of state. */
 	if (tty->link && tty->link->packet) {
 		int extproc = (old_termios.c_lflag & EXTPROC) |
-				(tty->termios->c_lflag & EXTPROC);
+				(tty->termios.c_lflag & EXTPROC);
 		int old_flow = ((old_termios.c_iflag & IXON) &&
 				(old_termios.c_cc[VSTOP] == '\023') &&
 				(old_termios.c_cc[VSTART] == '\021'));
@@ -542,7 +542,7 @@
 	if (tty->ops->set_termios)
 		(*tty->ops->set_termios)(tty, &old_termios);
 	else
-		tty_termios_copy_hw(tty->termios, &old_termios);
+		tty_termios_copy_hw(&tty->termios, &old_termios);
 
 	ld = tty_ldisc_ref(tty);
 	if (ld != NULL) {
@@ -578,7 +578,7 @@
 		return retval;
 
 	mutex_lock(&tty->termios_mutex);
-	memcpy(&tmp_termios, tty->termios, sizeof(struct ktermios));
+	tmp_termios = tty->termios;
 	mutex_unlock(&tty->termios_mutex);
 
 	if (opt & TERMIOS_TERMIO) {
@@ -632,14 +632,14 @@
 static void copy_termios(struct tty_struct *tty, struct ktermios *kterm)
 {
 	mutex_lock(&tty->termios_mutex);
-	memcpy(kterm, tty->termios, sizeof(struct ktermios));
+	*kterm = tty->termios;
 	mutex_unlock(&tty->termios_mutex);
 }
 
 static void copy_termios_locked(struct tty_struct *tty, struct ktermios *kterm)
 {
 	mutex_lock(&tty->termios_mutex);
-	memcpy(kterm, tty->termios_locked, sizeof(struct ktermios));
+	*kterm = tty->termios_locked;
 	mutex_unlock(&tty->termios_mutex);
 }
 
@@ -707,16 +707,16 @@
 {
 	int flags = 0;
 
-	if (!(tty->termios->c_lflag & ICANON)) {
-		if (tty->termios->c_lflag & ISIG)
+	if (!(tty->termios.c_lflag & ICANON)) {
+		if (tty->termios.c_lflag & ISIG)
 			flags |= 0x02;		/* cbreak */
 		else
 			flags |= 0x20;		/* raw */
 	}
-	if (tty->termios->c_lflag & ECHO)
+	if (tty->termios.c_lflag & ECHO)
 		flags |= 0x08;			/* echo */
-	if (tty->termios->c_oflag & OPOST)
-		if (tty->termios->c_oflag & ONLCR)
+	if (tty->termios.c_oflag & OPOST)
+		if (tty->termios.c_oflag & ONLCR)
 			flags |= 0x10;		/* crmod */
 	return flags;
 }
@@ -726,10 +726,10 @@
 	struct sgttyb tmp;
 
 	mutex_lock(&tty->termios_mutex);
-	tmp.sg_ispeed = tty->termios->c_ispeed;
-	tmp.sg_ospeed = tty->termios->c_ospeed;
-	tmp.sg_erase = tty->termios->c_cc[VERASE];
-	tmp.sg_kill = tty->termios->c_cc[VKILL];
+	tmp.sg_ispeed = tty->termios.c_ispeed;
+	tmp.sg_ospeed = tty->termios.c_ospeed;
+	tmp.sg_erase = tty->termios.c_cc[VERASE];
+	tmp.sg_kill = tty->termios.c_cc[VKILL];
 	tmp.sg_flags = get_sgflags(tty);
 	mutex_unlock(&tty->termios_mutex);
 
@@ -787,7 +787,7 @@
 		return -EFAULT;
 
 	mutex_lock(&tty->termios_mutex);
-	termios = *tty->termios;
+	termios = tty->termios;
 	termios.c_cc[VERASE] = tmp.sg_erase;
 	termios.c_cc[VKILL] = tmp.sg_kill;
 	set_sgflags(&termios, tmp.sg_flags);
@@ -808,12 +808,12 @@
 	struct tchars tmp;
 
 	mutex_lock(&tty->termios_mutex);
-	tmp.t_intrc = tty->termios->c_cc[VINTR];
-	tmp.t_quitc = tty->termios->c_cc[VQUIT];
-	tmp.t_startc = tty->termios->c_cc[VSTART];
-	tmp.t_stopc = tty->termios->c_cc[VSTOP];
-	tmp.t_eofc = tty->termios->c_cc[VEOF];
-	tmp.t_brkc = tty->termios->c_cc[VEOL2];	/* what is brkc anyway? */
+	tmp.t_intrc = tty->termios.c_cc[VINTR];
+	tmp.t_quitc = tty->termios.c_cc[VQUIT];
+	tmp.t_startc = tty->termios.c_cc[VSTART];
+	tmp.t_stopc = tty->termios.c_cc[VSTOP];
+	tmp.t_eofc = tty->termios.c_cc[VEOF];
+	tmp.t_brkc = tty->termios.c_cc[VEOL2];	/* what is brkc anyway? */
 	mutex_unlock(&tty->termios_mutex);
 	return copy_to_user(tchars, &tmp, sizeof(tmp)) ? -EFAULT : 0;
 }
@@ -825,12 +825,12 @@
 	if (copy_from_user(&tmp, tchars, sizeof(tmp)))
 		return -EFAULT;
 	mutex_lock(&tty->termios_mutex);
-	tty->termios->c_cc[VINTR] = tmp.t_intrc;
-	tty->termios->c_cc[VQUIT] = tmp.t_quitc;
-	tty->termios->c_cc[VSTART] = tmp.t_startc;
-	tty->termios->c_cc[VSTOP] = tmp.t_stopc;
-	tty->termios->c_cc[VEOF] = tmp.t_eofc;
-	tty->termios->c_cc[VEOL2] = tmp.t_brkc;	/* what is brkc anyway? */
+	tty->termios.c_cc[VINTR] = tmp.t_intrc;
+	tty->termios.c_cc[VQUIT] = tmp.t_quitc;
+	tty->termios.c_cc[VSTART] = tmp.t_startc;
+	tty->termios.c_cc[VSTOP] = tmp.t_stopc;
+	tty->termios.c_cc[VEOF] = tmp.t_eofc;
+	tty->termios.c_cc[VEOL2] = tmp.t_brkc;	/* what is brkc anyway? */
 	mutex_unlock(&tty->termios_mutex);
 	return 0;
 }
@@ -842,14 +842,14 @@
 	struct ltchars tmp;
 
 	mutex_lock(&tty->termios_mutex);
-	tmp.t_suspc = tty->termios->c_cc[VSUSP];
+	tmp.t_suspc = tty->termios.c_cc[VSUSP];
 	/* what is dsuspc anyway? */
-	tmp.t_dsuspc = tty->termios->c_cc[VSUSP];
-	tmp.t_rprntc = tty->termios->c_cc[VREPRINT];
+	tmp.t_dsuspc = tty->termios.c_cc[VSUSP];
+	tmp.t_rprntc = tty->termios.c_cc[VREPRINT];
 	/* what is flushc anyway? */
-	tmp.t_flushc = tty->termios->c_cc[VEOL2];
-	tmp.t_werasc = tty->termios->c_cc[VWERASE];
-	tmp.t_lnextc = tty->termios->c_cc[VLNEXT];
+	tmp.t_flushc = tty->termios.c_cc[VEOL2];
+	tmp.t_werasc = tty->termios.c_cc[VWERASE];
+	tmp.t_lnextc = tty->termios.c_cc[VLNEXT];
 	mutex_unlock(&tty->termios_mutex);
 	return copy_to_user(ltchars, &tmp, sizeof(tmp)) ? -EFAULT : 0;
 }
@@ -862,14 +862,14 @@
 		return -EFAULT;
 
 	mutex_lock(&tty->termios_mutex);
-	tty->termios->c_cc[VSUSP] = tmp.t_suspc;
+	tty->termios.c_cc[VSUSP] = tmp.t_suspc;
 	/* what is dsuspc anyway? */
-	tty->termios->c_cc[VEOL2] = tmp.t_dsuspc;
-	tty->termios->c_cc[VREPRINT] = tmp.t_rprntc;
+	tty->termios.c_cc[VEOL2] = tmp.t_dsuspc;
+	tty->termios.c_cc[VREPRINT] = tmp.t_rprntc;
 	/* what is flushc anyway? */
-	tty->termios->c_cc[VEOL2] = tmp.t_flushc;
-	tty->termios->c_cc[VWERASE] = tmp.t_werasc;
-	tty->termios->c_cc[VLNEXT] = tmp.t_lnextc;
+	tty->termios.c_cc[VEOL2] = tmp.t_flushc;
+	tty->termios.c_cc[VWERASE] = tmp.t_werasc;
+	tty->termios.c_cc[VLNEXT] = tmp.t_lnextc;
 	mutex_unlock(&tty->termios_mutex);
 	return 0;
 }
@@ -920,12 +920,12 @@
 	struct ktermios old;
 
 	mutex_lock(&tty->termios_mutex);
-	old = *tty->termios;
-	tty->termios->c_cflag &= ~CLOCAL;
-	tty->termios->c_cflag |= bit;
+	old = tty->termios;
+	tty->termios.c_cflag &= ~CLOCAL;
+	tty->termios.c_cflag |= bit;
 	if (tty->ops->set_termios)
 		tty->ops->set_termios(tty, &old);
-	if ((tty->termios->c_cflag & CLOCAL) != bit)
+	if ((tty->termios.c_cflag & CLOCAL) != bit)
 		ret = -EINVAL;
 	mutex_unlock(&tty->termios_mutex);
 	return ret;
@@ -1031,7 +1031,7 @@
 					       (struct termios __user *) arg))
 			return -EFAULT;
 		mutex_lock(&real_tty->termios_mutex);
-		memcpy(real_tty->termios_locked, &kterm, sizeof(struct ktermios));
+		real_tty->termios_locked = kterm;
 		mutex_unlock(&real_tty->termios_mutex);
 		return 0;
 #else
@@ -1048,7 +1048,7 @@
 					       (struct termios __user *) arg))
 			return -EFAULT;
 		mutex_lock(&real_tty->termios_mutex);
-		memcpy(real_tty->termios_locked, &kterm, sizeof(struct ktermios));
+		real_tty->termios_locked = kterm;
 		mutex_unlock(&real_tty->termios_mutex);
 		return ret;
 #endif
diff --git a/drivers/tty/tty_ldisc.c b/drivers/tty/tty_ldisc.c
index 6f99c99..4d7b562 100644
--- a/drivers/tty/tty_ldisc.c
+++ b/drivers/tty/tty_ldisc.c
@@ -413,7 +413,7 @@
 static void tty_set_termios_ldisc(struct tty_struct *tty, int num)
 {
 	mutex_lock(&tty->termios_mutex);
-	tty->termios->c_line = num;
+	tty->termios.c_line = num;
 	mutex_unlock(&tty->termios_mutex);
 }
 
@@ -568,7 +568,7 @@
 	if (IS_ERR(new_ldisc))
 		return PTR_ERR(new_ldisc);
 
-	tty_lock();
+	tty_lock(tty);
 	/*
 	 *	We need to look at the tty locking here for pty/tty pairs
 	 *	when both sides try to change in parallel.
@@ -582,12 +582,12 @@
 	 */
 
 	if (tty->ldisc->ops->num == ldisc) {
-		tty_unlock();
+		tty_unlock(tty);
 		tty_ldisc_put(new_ldisc);
 		return 0;
 	}
 
-	tty_unlock();
+	tty_unlock(tty);
 	/*
 	 *	Problem: What do we do if this blocks ?
 	 *	We could deadlock here
@@ -595,7 +595,7 @@
 
 	tty_wait_until_sent(tty, 0);
 
-	tty_lock();
+	tty_lock(tty);
 	mutex_lock(&tty->ldisc_mutex);
 
 	/*
@@ -605,10 +605,10 @@
 
 	while (test_bit(TTY_LDISC_CHANGING, &tty->flags)) {
 		mutex_unlock(&tty->ldisc_mutex);
-		tty_unlock();
+		tty_unlock(tty);
 		wait_event(tty_ldisc_wait,
 			test_bit(TTY_LDISC_CHANGING, &tty->flags) == 0);
-		tty_lock();
+		tty_lock(tty);
 		mutex_lock(&tty->ldisc_mutex);
 	}
 
@@ -623,7 +623,7 @@
 
 	o_ldisc = tty->ldisc;
 
-	tty_unlock();
+	tty_unlock(tty);
 	/*
 	 *	Make sure we don't change while someone holds a
 	 *	reference to the line discipline. The TTY_LDISC bit
@@ -650,7 +650,7 @@
 
 	retval = tty_ldisc_wait_idle(tty, 5 * HZ);
 
-	tty_lock();
+	tty_lock(tty);
 	mutex_lock(&tty->ldisc_mutex);
 
 	/* handle wait idle failure locked */
@@ -665,7 +665,7 @@
 		clear_bit(TTY_LDISC_CHANGING, &tty->flags);
 		mutex_unlock(&tty->ldisc_mutex);
 		tty_ldisc_put(new_ldisc);
-		tty_unlock();
+		tty_unlock(tty);
 		return -EIO;
 	}
 
@@ -708,7 +708,7 @@
 	if (o_work)
 		schedule_work(&o_tty->buf.work);
 	mutex_unlock(&tty->ldisc_mutex);
-	tty_unlock();
+	tty_unlock(tty);
 	return retval;
 }
 
@@ -722,9 +722,9 @@
 static void tty_reset_termios(struct tty_struct *tty)
 {
 	mutex_lock(&tty->termios_mutex);
-	*tty->termios = tty->driver->init_termios;
-	tty->termios->c_ispeed = tty_termios_input_baud_rate(tty->termios);
-	tty->termios->c_ospeed = tty_termios_baud_rate(tty->termios);
+	tty->termios = tty->driver->init_termios;
+	tty->termios.c_ispeed = tty_termios_input_baud_rate(&tty->termios);
+	tty->termios.c_ospeed = tty_termios_baud_rate(&tty->termios);
 	mutex_unlock(&tty->termios_mutex);
 }
 
@@ -816,11 +816,11 @@
 	 * need to wait for another function taking the BTM
 	 */
 	clear_bit(TTY_LDISC, &tty->flags);
-	tty_unlock();
+	tty_unlock(tty);
 	cancel_work_sync(&tty->buf.work);
 	mutex_unlock(&tty->ldisc_mutex);
 retry:
-	tty_lock();
+	tty_lock(tty);
 	mutex_lock(&tty->ldisc_mutex);
 
 	/* At this point we have a closed ldisc and we want to
@@ -831,7 +831,7 @@
 		if (atomic_read(&tty->ldisc->users) != 1) {
 			char cur_n[TASK_COMM_LEN], tty_n[64];
 			long timeout = 3 * HZ;
-			tty_unlock();
+			tty_unlock(tty);
 
 			while (tty_ldisc_wait_idle(tty, timeout) == -EBUSY) {
 				timeout = MAX_SCHEDULE_TIMEOUT;
@@ -846,7 +846,7 @@
 
 		if (reset == 0) {
 
-			if (!tty_ldisc_reinit(tty, tty->termios->c_line))
+			if (!tty_ldisc_reinit(tty, tty->termios.c_line))
 				err = tty_ldisc_open(tty, tty->ldisc);
 			else
 				err = 1;
@@ -894,6 +894,23 @@
 	tty_ldisc_enable(tty);
 	return 0;
 }
+
+static void tty_ldisc_kill(struct tty_struct *tty)
+{
+	mutex_lock(&tty->ldisc_mutex);
+	/*
+	 * Now kill off the ldisc
+	 */
+	tty_ldisc_close(tty, tty->ldisc);
+	tty_ldisc_put(tty->ldisc);
+	/* Force an oops if we mess this up */
+	tty->ldisc = NULL;
+
+	/* Ensure the next open requests the N_TTY ldisc */
+	tty_set_termios_ldisc(tty, N_TTY);
+	mutex_unlock(&tty->ldisc_mutex);
+}
+
 /**
  *	tty_ldisc_release		-	release line discipline
  *	@tty: tty being shut down
@@ -912,28 +929,21 @@
 	 * race with the set_ldisc code path.
 	 */
 
-	tty_unlock();
+	tty_lock_pair(tty, o_tty);
 	tty_ldisc_halt(tty);
 	tty_ldisc_flush_works(tty);
-	tty_lock();
-
-	mutex_lock(&tty->ldisc_mutex);
-	/*
-	 * Now kill off the ldisc
-	 */
-	tty_ldisc_close(tty, tty->ldisc);
-	tty_ldisc_put(tty->ldisc);
-	/* Force an oops if we mess this up */
-	tty->ldisc = NULL;
-
-	/* Ensure the next open requests the N_TTY ldisc */
-	tty_set_termios_ldisc(tty, N_TTY);
-	mutex_unlock(&tty->ldisc_mutex);
+	if (o_tty) {
+		tty_ldisc_halt(o_tty);
+		tty_ldisc_flush_works(o_tty);
+	}
 
 	/* This will need doing differently if we need to lock */
-	if (o_tty)
-		tty_ldisc_release(o_tty, NULL);
+	tty_ldisc_kill(tty);
 
+	if (o_tty)
+		tty_ldisc_kill(o_tty);
+
+	tty_unlock_pair(tty, o_tty);
 	/* And the memory resources remaining (buffers, termios) will be
 	   disposed of when the kref hits zero */
 }
diff --git a/drivers/tty/tty_mutex.c b/drivers/tty/tty_mutex.c
index 9ff986c..67feac9 100644
--- a/drivers/tty/tty_mutex.c
+++ b/drivers/tty/tty_mutex.c
@@ -4,29 +4,70 @@
 #include <linux/semaphore.h>
 #include <linux/sched.h>
 
-/*
- * The 'big tty mutex'
- *
- * This mutex is taken and released by tty_lock() and tty_unlock(),
- * replacing the older big kernel lock.
- * It can no longer be taken recursively, and does not get
- * released implicitly while sleeping.
- *
- * Don't use in new code.
- */
-static DEFINE_MUTEX(big_tty_mutex);
+/* Legacy tty mutex glue */
+
+enum {
+	TTY_MUTEX_NORMAL,
+	TTY_MUTEX_NESTED,
+};
 
 /*
  * Getting the big tty mutex.
  */
-void __lockfunc tty_lock(void)
+
+static void __lockfunc tty_lock_nested(struct tty_struct *tty,
+				       unsigned int subclass)
 {
-	mutex_lock(&big_tty_mutex);
+	if (tty->magic != TTY_MAGIC) {
+		printk(KERN_ERR "L Bad %p\n", tty);
+		WARN_ON(1);
+		return;
+	}
+	tty_kref_get(tty);
+	mutex_lock_nested(&tty->legacy_mutex, subclass);
+}
+
+void __lockfunc tty_lock(struct tty_struct *tty)
+{
+	return tty_lock_nested(tty, TTY_MUTEX_NORMAL);
 }
 EXPORT_SYMBOL(tty_lock);
 
-void __lockfunc tty_unlock(void)
+void __lockfunc tty_unlock(struct tty_struct *tty)
 {
-	mutex_unlock(&big_tty_mutex);
+	if (tty->magic != TTY_MAGIC) {
+		printk(KERN_ERR "U Bad %p\n", tty);
+		WARN_ON(1);
+		return;
+	}
+	mutex_unlock(&tty->legacy_mutex);
+	tty_kref_put(tty);
 }
 EXPORT_SYMBOL(tty_unlock);
+
+/*
+ * Getting the big tty mutex for a pair of ttys with lock ordering
+ * On a non pty/tty pair tty2 can be NULL which is just fine.
+ */
+void __lockfunc tty_lock_pair(struct tty_struct *tty,
+					struct tty_struct *tty2)
+{
+	if (tty < tty2) {
+		tty_lock(tty);
+		tty_lock_nested(tty2, TTY_MUTEX_NESTED);
+	} else {
+		if (tty2 && tty2 != tty)
+			tty_lock(tty2);
+		tty_lock_nested(tty, TTY_MUTEX_NESTED);
+	}
+}
+EXPORT_SYMBOL(tty_lock_pair);
+
+void __lockfunc tty_unlock_pair(struct tty_struct *tty,
+						struct tty_struct *tty2)
+{
+	tty_unlock(tty);
+	if (tty2 && tty2 != tty)
+		tty_unlock(tty2);
+}
+EXPORT_SYMBOL(tty_unlock_pair);
diff --git a/drivers/tty/tty_port.c b/drivers/tty/tty_port.c
index bf6e238..d7bdd8d 100644
--- a/drivers/tty/tty_port.c
+++ b/drivers/tty/tty_port.c
@@ -33,6 +33,70 @@
 }
 EXPORT_SYMBOL(tty_port_init);
 
+/**
+ * tty_port_link_device - link tty and tty_port
+ * @port: tty_port of the device
+ * @driver: tty_driver for this device
+ * @index: index of the tty
+ *
+ * Provide the tty layer wit ha link from a tty (specified by @index) to a
+ * tty_port (@port). Use this only if neither tty_port_register_device nor
+ * tty_port_install is used in the driver. If used, this has to be called before
+ * tty_register_driver.
+ */
+void tty_port_link_device(struct tty_port *port,
+		struct tty_driver *driver, unsigned index)
+{
+	if (WARN_ON(index >= driver->num))
+		return;
+	driver->ports[index] = port;
+}
+EXPORT_SYMBOL_GPL(tty_port_link_device);
+
+/**
+ * tty_port_register_device - register tty device
+ * @port: tty_port of the device
+ * @driver: tty_driver for this device
+ * @index: index of the tty
+ * @device: parent if exists, otherwise NULL
+ *
+ * It is the same as tty_register_device except the provided @port is linked to
+ * a concrete tty specified by @index. Use this or tty_port_install (or both).
+ * Call tty_port_link_device as a last resort.
+ */
+struct device *tty_port_register_device(struct tty_port *port,
+		struct tty_driver *driver, unsigned index,
+		struct device *device)
+{
+	tty_port_link_device(port, driver, index);
+	return tty_register_device(driver, index, device);
+}
+EXPORT_SYMBOL_GPL(tty_port_register_device);
+
+/**
+ * tty_port_register_device_attr - register tty device
+ * @port: tty_port of the device
+ * @driver: tty_driver for this device
+ * @index: index of the tty
+ * @device: parent if exists, otherwise NULL
+ * @drvdata: Driver data to be set to device.
+ * @attr_grp: Attribute group to be set on device.
+ *
+ * It is the same as tty_register_device_attr except the provided @port is
+ * linked to a concrete tty specified by @index. Use this or tty_port_install
+ * (or both). Call tty_port_link_device as a last resort.
+ */
+struct device *tty_port_register_device_attr(struct tty_port *port,
+		struct tty_driver *driver, unsigned index,
+		struct device *device, void *drvdata,
+		const struct attribute_group **attr_grp)
+{
+	tty_port_link_device(port, driver, index);
+	return tty_register_device_attr(driver, index, device, drvdata,
+			attr_grp);
+}
+EXPORT_SYMBOL_GPL(tty_port_register_device_attr);
+
 int tty_port_alloc_xmit_buf(struct tty_port *port)
 {
 	/* We may sleep in get_zeroed_page() */
@@ -230,7 +294,7 @@
 
 	/* block if port is in the process of being closed */
 	if (tty_hung_up_p(filp) || port->flags & ASYNC_CLOSING) {
-		wait_event_interruptible_tty(port->close_wait,
+		wait_event_interruptible_tty(tty, port->close_wait,
 				!(port->flags & ASYNC_CLOSING));
 		if (port->flags & ASYNC_HUP_NOTIFY)
 			return -EAGAIN;
@@ -246,7 +310,7 @@
 	}
 	if (filp->f_flags & O_NONBLOCK) {
 		/* Indicate we are open */
-		if (tty->termios->c_cflag & CBAUD)
+		if (tty->termios.c_cflag & CBAUD)
 			tty_port_raise_dtr_rts(port);
 		port->flags |= ASYNC_NORMAL_ACTIVE;
 		return 0;
@@ -270,7 +334,7 @@
 
 	while (1) {
 		/* Indicate we are open */
-		if (tty->termios->c_cflag & CBAUD)
+		if (tty->termios.c_cflag & CBAUD)
 			tty_port_raise_dtr_rts(port);
 
 		prepare_to_wait(&port->open_wait, &wait, TASK_INTERRUPTIBLE);
@@ -296,9 +360,9 @@
 			retval = -ERESTARTSYS;
 			break;
 		}
-		tty_unlock();
+		tty_unlock(tty);
 		schedule();
-		tty_lock();
+		tty_lock(tty);
 	}
 	finish_wait(&port->open_wait, &wait);
 
@@ -369,7 +433,7 @@
 
 	/* Drop DTR/RTS if HUPCL is set. This causes any attached modem to
 	   hang up the line */
-	if (tty->termios->c_cflag & HUPCL)
+	if (tty->termios.c_cflag & HUPCL)
 		tty_port_lower_dtr_rts(port);
 
 	/* Don't call port->drop for the last reference. Callers will want
@@ -413,6 +477,24 @@
 }
 EXPORT_SYMBOL(tty_port_close);
 
+/**
+ * tty_port_install - generic tty->ops->install handler
+ * @port: tty_port of the device
+ * @driver: tty_driver for this device
+ * @tty: tty to be installed
+ *
+ * It is the same as tty_standard_install except the provided @port is linked
+ * to a concrete tty specified by @tty. Use this or tty_port_register_device
+ * (or both). Call tty_port_link_device as a last resort.
+ */
+int tty_port_install(struct tty_port *port, struct tty_driver *driver,
+		struct tty_struct *tty)
+{
+	tty->port = port;
+	return tty_standard_install(driver, tty);
+}
+EXPORT_SYMBOL_GPL(tty_port_install);
+
 int tty_port_open(struct tty_port *port, struct tty_struct *tty,
 							struct file *filp)
 {
diff --git a/drivers/tty/vt/keyboard.c b/drivers/tty/vt/keyboard.c
index 48cc6f2..681765b 100644
--- a/drivers/tty/vt/keyboard.c
+++ b/drivers/tty/vt/keyboard.c
@@ -119,6 +119,7 @@
 
 static struct input_handler kbd_handler;
 static DEFINE_SPINLOCK(kbd_event_lock);
+static DEFINE_SPINLOCK(led_lock);
 static unsigned long key_down[BITS_TO_LONGS(KEY_CNT)];	/* keyboard key bitmap */
 static unsigned char shift_down[NR_SHIFT];		/* shift state counters.. */
 static bool dead_key_next;
@@ -310,7 +311,7 @@
 
 	if (tty) {
 		tty_insert_flip_char(tty, ch, 0);
-		con_schedule_flip(tty);
+		tty_schedule_flip(tty);
 	}
 }
 
@@ -325,7 +326,7 @@
 		tty_insert_flip_char(tty, *cp, 0);
 		cp++;
 	}
-	con_schedule_flip(tty);
+	tty_schedule_flip(tty);
 }
 
 static void applkey(struct vc_data *vc, int key, char mode)
@@ -586,7 +587,7 @@
 	if (!tty)
 		return;
 	tty_insert_flip_char(tty, 0, TTY_BREAK);
-	con_schedule_flip(tty);
+	tty_schedule_flip(tty);
 }
 
 static void fn_scroll_forw(struct vc_data *vc)
@@ -984,7 +985,7 @@
  * or (ii) whatever pattern of lights people want to show using KDSETLED,
  * or (iii) specified bits of specified words in kernel memory.
  */
-unsigned char getledstate(void)
+static unsigned char getledstate(void)
 {
 	return ledstate;
 }
@@ -992,7 +993,7 @@
 void setledstate(struct kbd_struct *kbd, unsigned int led)
 {
         unsigned long flags;
-        spin_lock_irqsave(&kbd_event_lock, flags);
+        spin_lock_irqsave(&led_lock, flags);
 	if (!(led & ~7)) {
 		ledioctl = led;
 		kbd->ledmode = LED_SHOW_IOCTL;
@@ -1000,7 +1001,7 @@
 		kbd->ledmode = LED_SHOW_FLAGS;
 
 	set_leds();
-	spin_unlock_irqrestore(&kbd_event_lock, flags);
+	spin_unlock_irqrestore(&led_lock, flags);
 }
 
 static inline unsigned char getleds(void)
@@ -1049,13 +1050,13 @@
  */
 int vt_get_leds(int console, int flag)
 {
-	unsigned long flags;
 	struct kbd_struct * kbd = kbd_table + console;
 	int ret;
+	unsigned long flags;
 
-	spin_lock_irqsave(&kbd_event_lock, flags);
+	spin_lock_irqsave(&led_lock, flags);
 	ret = vc_kbd_led(kbd, flag);
-	spin_unlock_irqrestore(&kbd_event_lock, flags);
+	spin_unlock_irqrestore(&led_lock, flags);
 
 	return ret;
 }
@@ -1091,11 +1092,11 @@
 void vt_kbd_con_start(int console)
 {
 	struct kbd_struct * kbd = kbd_table + console;
-/*	unsigned long flags; */
-/*	spin_lock_irqsave(&kbd_event_lock, flags); */
+	unsigned long flags;
+	spin_lock_irqsave(&led_lock, flags);
 	clr_vc_kbd_led(kbd, VC_SCROLLOCK);
 	set_leds();
-/*	spin_unlock_irqrestore(&kbd_event_lock, flags); */
+	spin_unlock_irqrestore(&led_lock, flags);
 }
 
 /**
@@ -1104,21 +1105,15 @@
  *
  *	Handle console stop. This is a wrapper for the VT layer
  *	so that we can keep kbd knowledge internal
- *
- *	FIXME: We eventually need to hold the kbd lock here to protect
- *	the LED updating. We can't do it yet because fn_hold calls stop_tty
- *	and start_tty under the kbd_event_lock, while normal tty paths
- *	don't hold the lock. We probably need to split out an LED lock
- *	but not during an -rc release!
  */
 void vt_kbd_con_stop(int console)
 {
 	struct kbd_struct * kbd = kbd_table + console;
-/*	unsigned long flags; */
-/*	spin_lock_irqsave(&kbd_event_lock, flags); */
+	unsigned long flags;
+	spin_lock_irqsave(&led_lock, flags);
 	set_vc_kbd_led(kbd, VC_SCROLLOCK);
 	set_leds();
-/*	spin_unlock_irqrestore(&kbd_event_lock, flags); */
+	spin_unlock_irqrestore(&led_lock, flags);
 }
 
 /*
@@ -1130,7 +1125,12 @@
  */
 static void kbd_bh(unsigned long dummy)
 {
-	unsigned char leds = getleds();
+	unsigned char leds;
+	unsigned long flags;
+	
+	spin_lock_irqsave(&led_lock, flags);
+	leds = getleds();
+	spin_unlock_irqrestore(&led_lock, flags);
 
 	if (leds != ledstate) {
 		input_handler_for_each_handle(&kbd_handler, &leds,
@@ -2035,11 +2035,11 @@
 			return -EPERM;
 		if (arg & ~0x77)
 			return -EINVAL;
-                spin_lock_irqsave(&kbd_event_lock, flags);
+                spin_lock_irqsave(&led_lock, flags);
 		kbd->ledflagstate = (arg & 7);
 		kbd->default_ledflagstate = ((arg >> 4) & 7);
 		set_leds();
-                spin_unlock_irqrestore(&kbd_event_lock, flags);
+                spin_unlock_irqrestore(&led_lock, flags);
 		return 0;
 
 	/* the ioctls below only set the lights, not the functions */
@@ -2134,8 +2134,10 @@
 	clr_vc_kbd_mode(kbd, VC_CRLF);
 	kbd->lockstate = 0;
 	kbd->slockstate = 0;
+	spin_lock(&led_lock);
 	kbd->ledmode = LED_SHOW_FLAGS;
 	kbd->ledflagstate = kbd->default_ledflagstate;
+	spin_unlock(&led_lock);
 	/* do not do set_leds here because this causes an endless tasklet loop
 	   when the keyboard hasn't been initialized yet */
 	spin_unlock_irqrestore(&kbd_event_lock, flags);
diff --git a/drivers/tty/vt/vt.c b/drivers/tty/vt/vt.c
index 84cbf29..999ca63 100644
--- a/drivers/tty/vt/vt.c
+++ b/drivers/tty/vt/vt.c
@@ -537,45 +537,27 @@
 
 static void insert_char(struct vc_data *vc, unsigned int nr)
 {
-	unsigned short *p, *q = (unsigned short *)vc->vc_pos;
+	unsigned short *p = (unsigned short *) vc->vc_pos;
 
-	p = q + vc->vc_cols - nr - vc->vc_x;
-	while (--p >= q)
-		scr_writew(scr_readw(p), p + nr);
-	scr_memsetw(q, vc->vc_video_erase_char, nr * 2);
+	scr_memmovew(p + nr, p, vc->vc_cols - vc->vc_x);
+	scr_memsetw(p, vc->vc_video_erase_char, nr * 2);
 	vc->vc_need_wrap = 0;
-	if (DO_UPDATE(vc)) {
-		unsigned short oldattr = vc->vc_attr;
-		vc->vc_sw->con_bmove(vc, vc->vc_y, vc->vc_x, vc->vc_y, vc->vc_x + nr, 1,
-				     vc->vc_cols - vc->vc_x - nr);
-		vc->vc_attr = vc->vc_video_erase_char >> 8;
-		while (nr--)
-			vc->vc_sw->con_putc(vc, vc->vc_video_erase_char, vc->vc_y, vc->vc_x + nr);
-		vc->vc_attr = oldattr;
-	}
+	if (DO_UPDATE(vc))
+		do_update_region(vc, (unsigned long) p,
+			(vc->vc_cols - vc->vc_x) / 2 + 1);
 }
 
 static void delete_char(struct vc_data *vc, unsigned int nr)
 {
-	unsigned int i = vc->vc_x;
-	unsigned short *p = (unsigned short *)vc->vc_pos;
+	unsigned short *p = (unsigned short *) vc->vc_pos;
 
-	while (++i <= vc->vc_cols - nr) {
-		scr_writew(scr_readw(p+nr), p);
-		p++;
-	}
-	scr_memsetw(p, vc->vc_video_erase_char, nr * 2);
+	scr_memcpyw(p, p + nr, vc->vc_cols - vc->vc_x - nr);
+	scr_memsetw(p + vc->vc_cols - vc->vc_x - nr, vc->vc_video_erase_char,
+			nr * 2);
 	vc->vc_need_wrap = 0;
-	if (DO_UPDATE(vc)) {
-		unsigned short oldattr = vc->vc_attr;
-		vc->vc_sw->con_bmove(vc, vc->vc_y, vc->vc_x + nr, vc->vc_y, vc->vc_x, 1,
-				     vc->vc_cols - vc->vc_x - nr);
-		vc->vc_attr = vc->vc_video_erase_char >> 8;
-		while (nr--)
-			vc->vc_sw->con_putc(vc, vc->vc_video_erase_char, vc->vc_y,
-				     vc->vc_cols - 1 - nr);
-		vc->vc_attr = oldattr;
-	}
+	if (DO_UPDATE(vc))
+		do_update_region(vc, (unsigned long) p,
+			(vc->vc_cols - vc->vc_x) / 2);
 }
 
 static int softcursor_original;
@@ -1172,45 +1154,26 @@
 		case 0:	/* erase from cursor to end of display */
 			count = (vc->vc_scr_end - vc->vc_pos) >> 1;
 			start = (unsigned short *)vc->vc_pos;
-			if (DO_UPDATE(vc)) {
-				/* do in two stages */
-				vc->vc_sw->con_clear(vc, vc->vc_y, vc->vc_x, 1,
-					      vc->vc_cols - vc->vc_x);
-				vc->vc_sw->con_clear(vc, vc->vc_y + 1, 0,
-					      vc->vc_rows - vc->vc_y - 1,
-					      vc->vc_cols);
-			}
 			break;
 		case 1:	/* erase from start to cursor */
 			count = ((vc->vc_pos - vc->vc_origin) >> 1) + 1;
 			start = (unsigned short *)vc->vc_origin;
-			if (DO_UPDATE(vc)) {
-				/* do in two stages */
-				vc->vc_sw->con_clear(vc, 0, 0, vc->vc_y,
-					      vc->vc_cols);
-				vc->vc_sw->con_clear(vc, vc->vc_y, 0, 1,
-					      vc->vc_x + 1);
-			}
 			break;
 		case 3: /* erase scroll-back buffer (and whole display) */
 			scr_memsetw(vc->vc_screenbuf, vc->vc_video_erase_char,
 				    vc->vc_screenbuf_size >> 1);
 			set_origin(vc);
-			if (CON_IS_VISIBLE(vc))
-				update_screen(vc);
 			/* fall through */
 		case 2: /* erase whole display */
 			count = vc->vc_cols * vc->vc_rows;
 			start = (unsigned short *)vc->vc_origin;
-			if (DO_UPDATE(vc))
-				vc->vc_sw->con_clear(vc, 0, 0,
-					      vc->vc_rows,
-					      vc->vc_cols);
 			break;
 		default:
 			return;
 	}
 	scr_memsetw(start, vc->vc_video_erase_char, 2 * count);
+	if (DO_UPDATE(vc))
+		do_update_region(vc, (unsigned long) start, count);
 	vc->vc_need_wrap = 0;
 }
 
@@ -1223,29 +1186,22 @@
 		case 0:	/* erase from cursor to end of line */
 			count = vc->vc_cols - vc->vc_x;
 			start = (unsigned short *)vc->vc_pos;
-			if (DO_UPDATE(vc))
-				vc->vc_sw->con_clear(vc, vc->vc_y, vc->vc_x, 1,
-						     vc->vc_cols - vc->vc_x);
 			break;
 		case 1:	/* erase from start of line to cursor */
 			start = (unsigned short *)(vc->vc_pos - (vc->vc_x << 1));
 			count = vc->vc_x + 1;
-			if (DO_UPDATE(vc))
-				vc->vc_sw->con_clear(vc, vc->vc_y, 0, 1,
-						     vc->vc_x + 1);
 			break;
 		case 2: /* erase whole line */
 			start = (unsigned short *)(vc->vc_pos - (vc->vc_x << 1));
 			count = vc->vc_cols;
-			if (DO_UPDATE(vc))
-				vc->vc_sw->con_clear(vc, vc->vc_y, 0, 1,
-					      vc->vc_cols);
 			break;
 		default:
 			return;
 	}
 	scr_memsetw(start, vc->vc_video_erase_char, 2 * count);
 	vc->vc_need_wrap = 0;
+	if (DO_UPDATE(vc))
+		do_update_region(vc, (unsigned long) start, count);
 }
 
 static void csi_X(struct vc_data *vc, int vpar) /* erase the following vpar positions */
@@ -1380,7 +1336,7 @@
 		tty_insert_flip_char(tty, *p, 0);
 		p++;
 	}
-	con_schedule_flip(tty);
+	tty_schedule_flip(tty);
 }
 
 static void cursor_report(struct vc_data *vc, struct tty_struct *tty)
@@ -2792,41 +2748,52 @@
 /*
  * Allocate the console screen memory.
  */
-static int con_open(struct tty_struct *tty, struct file *filp)
+static int con_install(struct tty_driver *driver, struct tty_struct *tty)
 {
 	unsigned int currcons = tty->index;
-	int ret = 0;
+	struct vc_data *vc;
+	int ret;
 
 	console_lock();
-	if (tty->driver_data == NULL) {
-		ret = vc_allocate(currcons);
-		if (ret == 0) {
-			struct vc_data *vc = vc_cons[currcons].d;
+	ret = vc_allocate(currcons);
+	if (ret)
+		goto unlock;
 
-			/* Still being freed */
-			if (vc->port.tty) {
-				console_unlock();
-				return -ERESTARTSYS;
-			}
-			tty->driver_data = vc;
-			vc->port.tty = tty;
+	vc = vc_cons[currcons].d;
 
-			if (!tty->winsize.ws_row && !tty->winsize.ws_col) {
-				tty->winsize.ws_row = vc_cons[currcons].d->vc_rows;
-				tty->winsize.ws_col = vc_cons[currcons].d->vc_cols;
-			}
-			if (vc->vc_utf)
-				tty->termios->c_iflag |= IUTF8;
-			else
-				tty->termios->c_iflag &= ~IUTF8;
-			console_unlock();
-			return ret;
-		}
+	/* Still being freed */
+	if (vc->port.tty) {
+		ret = -ERESTARTSYS;
+		goto unlock;
 	}
+
+	ret = tty_port_install(&vc->port, driver, tty);
+	if (ret)
+		goto unlock;
+
+	tty->driver_data = vc;
+	vc->port.tty = tty;
+
+	if (!tty->winsize.ws_row && !tty->winsize.ws_col) {
+		tty->winsize.ws_row = vc_cons[currcons].d->vc_rows;
+		tty->winsize.ws_col = vc_cons[currcons].d->vc_cols;
+	}
+	if (vc->vc_utf)
+		tty->termios.c_iflag |= IUTF8;
+	else
+		tty->termios.c_iflag &= ~IUTF8;
+unlock:
 	console_unlock();
 	return ret;
 }
 
+static int con_open(struct tty_struct *tty, struct file *filp)
+{
+	/* everything done in install */
+	return 0;
+}
+
+
 static void con_close(struct tty_struct *tty, struct file *filp)
 {
 	/* Nothing to do - we defer to shutdown */
@@ -2839,7 +2806,6 @@
 	console_lock();
 	vc->port.tty = NULL;
 	console_unlock();
-	tty_shutdown(tty);
 }
 
 static int default_italic_color    = 2; // green (ASCII)
@@ -2947,6 +2913,7 @@
 console_initcall(con_init);
 
 static const struct tty_operations con_ops = {
+	.install = con_install,
 	.open = con_open,
 	.close = con_close,
 	.write = con_write,
diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c
index f763ed7..ff7b5a8 100644
--- a/drivers/usb/class/cdc-acm.c
+++ b/drivers/usb/class/cdc-acm.c
@@ -826,7 +826,7 @@
 						struct ktermios *termios_old)
 {
 	struct acm *acm = tty->driver_data;
-	struct ktermios *termios = tty->termios;
+	struct ktermios *termios = &tty->termios;
 	struct usb_cdc_line_coding newline;
 	int newctrl = acm->ctrlout;
 
@@ -1299,7 +1299,8 @@
 	usb_set_intfdata(data_interface, acm);
 
 	usb_get_intf(control_interface);
-	tty_register_device(acm_tty_driver, minor, &control_interface->dev);
+	tty_port_register_device(&acm->port, acm_tty_driver, minor,
+			&control_interface->dev);
 
 	return 0;
 alloc_fail7:
diff --git a/drivers/usb/gadget/u_serial.c b/drivers/usb/gadget/u_serial.c
index 5b3f5ff..2b5534c2 100644
--- a/drivers/usb/gadget/u_serial.c
+++ b/drivers/usb/gadget/u_serial.c
@@ -1129,7 +1129,8 @@
 	for (i = 0; i < count; i++) {
 		struct device	*tty_dev;
 
-		tty_dev = tty_register_device(gs_tty_driver, i, &g->dev);
+		tty_dev = tty_port_register_device(&ports[i].port->port,
+				gs_tty_driver, i, &g->dev);
 		if (IS_ERR(tty_dev))
 			pr_warning("%s: no classdev for port %d, err %ld\n",
 				__func__, i, PTR_ERR(tty_dev));
diff --git a/drivers/usb/serial/ark3116.c b/drivers/usb/serial/ark3116.c
index f8ce97d..3b98fb7 100644
--- a/drivers/usb/serial/ark3116.c
+++ b/drivers/usb/serial/ark3116.c
@@ -215,7 +215,7 @@
 
 static void ark3116_init_termios(struct tty_struct *tty)
 {
-	struct ktermios *termios = tty->termios;
+	struct ktermios *termios = &tty->termios;
 	*termios = tty_std_termios;
 	termios->c_cflag = B9600 | CS8
 				      | CREAD | HUPCL | CLOCAL;
@@ -229,7 +229,7 @@
 {
 	struct usb_serial *serial = port->serial;
 	struct ark3116_private *priv = usb_get_serial_port_data(port);
-	struct ktermios *termios = tty->termios;
+	struct ktermios *termios = &tty->termios;
 	unsigned int cflag = termios->c_cflag;
 	int bps = tty_get_baud_rate(tty);
 	int quot;
diff --git a/drivers/usb/serial/belkin_sa.c b/drivers/usb/serial/belkin_sa.c
index 6b73656..a46df73 100644
--- a/drivers/usb/serial/belkin_sa.c
+++ b/drivers/usb/serial/belkin_sa.c
@@ -307,7 +307,7 @@
 	unsigned long control_state;
 	int bad_flow_control;
 	speed_t baud;
-	struct ktermios *termios = tty->termios;
+	struct ktermios *termios = &tty->termios;
 
 	iflag = termios->c_iflag;
 	cflag = termios->c_cflag;
diff --git a/drivers/usb/serial/console.c b/drivers/usb/serial/console.c
index b9cca6d..9a56428 100644
--- a/drivers/usb/serial/console.c
+++ b/drivers/usb/serial/console.c
@@ -165,8 +165,8 @@
 		}
 
 		if (serial->type->set_termios) {
-			tty->termios->c_cflag = cflag;
-			tty_termios_encode_baud_rate(tty->termios, baud, baud);
+			tty->termios.c_cflag = cflag;
+			tty_termios_encode_baud_rate(&tty->termios, baud, baud);
 			memset(&dummy, 0, sizeof(struct ktermios));
 			serial->type->set_termios(tty, port, &dummy);
 
diff --git a/drivers/usb/serial/cp210x.c b/drivers/usb/serial/cp210x.c
index 1e71079..ba5e07e1 100644
--- a/drivers/usb/serial/cp210x.c
+++ b/drivers/usb/serial/cp210x.c
@@ -469,7 +469,7 @@
 
 	if (tty) {
 		cp210x_get_termios_port(tty->driver_data,
-			&tty->termios->c_cflag, &baud);
+			&tty->termios.c_cflag, &baud);
 		tty_encode_baud_rate(tty, baud, baud);
 	}
 
@@ -631,7 +631,7 @@
 {
 	u32 baud;
 
-	baud = tty->termios->c_ospeed;
+	baud = tty->termios.c_ospeed;
 
 	/* This maps the requested rate to a rate valid on cp2102 or cp2103,
 	 * or to an arbitrary rate in [1M,2M].
@@ -665,10 +665,10 @@
 	if (!tty)
 		return;
 
-	cflag = tty->termios->c_cflag;
+	cflag = tty->termios.c_cflag;
 	old_cflag = old_termios->c_cflag;
 
-	if (tty->termios->c_ospeed != old_termios->c_ospeed)
+	if (tty->termios.c_ospeed != old_termios->c_ospeed)
 		cp210x_change_speed(tty, port, old_termios);
 
 	/* If the number of data bits is to be updated */
diff --git a/drivers/usb/serial/cypress_m8.c b/drivers/usb/serial/cypress_m8.c
index b78c34e..be34f15 100644
--- a/drivers/usb/serial/cypress_m8.c
+++ b/drivers/usb/serial/cypress_m8.c
@@ -922,38 +922,38 @@
 	   early enough */
 	if (!priv->termios_initialized) {
 		if (priv->chiptype == CT_EARTHMATE) {
-			*(tty->termios) = tty_std_termios;
-			tty->termios->c_cflag = B4800 | CS8 | CREAD | HUPCL |
+			tty->termios = tty_std_termios;
+			tty->termios.c_cflag = B4800 | CS8 | CREAD | HUPCL |
 				CLOCAL;
-			tty->termios->c_ispeed = 4800;
-			tty->termios->c_ospeed = 4800;
+			tty->termios.c_ispeed = 4800;
+			tty->termios.c_ospeed = 4800;
 		} else if (priv->chiptype == CT_CYPHIDCOM) {
-			*(tty->termios) = tty_std_termios;
-			tty->termios->c_cflag = B9600 | CS8 | CREAD | HUPCL |
+			tty->termios = tty_std_termios;
+			tty->termios.c_cflag = B9600 | CS8 | CREAD | HUPCL |
 				CLOCAL;
-			tty->termios->c_ispeed = 9600;
-			tty->termios->c_ospeed = 9600;
+			tty->termios.c_ispeed = 9600;
+			tty->termios.c_ospeed = 9600;
 		} else if (priv->chiptype == CT_CA42V2) {
-			*(tty->termios) = tty_std_termios;
-			tty->termios->c_cflag = B9600 | CS8 | CREAD | HUPCL |
+			tty->termios = tty_std_termios;
+			tty->termios.c_cflag = B9600 | CS8 | CREAD | HUPCL |
 				CLOCAL;
-			tty->termios->c_ispeed = 9600;
-			tty->termios->c_ospeed = 9600;
+			tty->termios.c_ispeed = 9600;
+			tty->termios.c_ospeed = 9600;
 		}
 		priv->termios_initialized = 1;
 	}
 	spin_unlock_irqrestore(&priv->lock, flags);
 
 	/* Unsupported features need clearing */
-	tty->termios->c_cflag &= ~(CMSPAR|CRTSCTS);
+	tty->termios.c_cflag &= ~(CMSPAR|CRTSCTS);
 
-	cflag = tty->termios->c_cflag;
-	iflag = tty->termios->c_iflag;
+	cflag = tty->termios.c_cflag;
+	iflag = tty->termios.c_iflag;
 
 	/* check if there are new settings */
 	if (old_termios) {
 		spin_lock_irqsave(&priv->lock, flags);
-		priv->tmp_termios = *(tty->termios);
+		priv->tmp_termios = tty->termios;
 		spin_unlock_irqrestore(&priv->lock, flags);
 	}
 
@@ -1021,7 +1021,7 @@
 				"4800bps.");
 		/* define custom termios settings for NMEA protocol */
 
-		tty->termios->c_iflag /* input modes - */
+		tty->termios.c_iflag /* input modes - */
 			&= ~(IGNBRK  /* disable ignore break */
 			| BRKINT     /* disable break causes interrupt */
 			| PARMRK     /* disable mark parity errors */
@@ -1031,10 +1031,10 @@
 			| ICRNL      /* disable translate CR to NL */
 			| IXON);     /* disable enable XON/XOFF flow control */
 
-		tty->termios->c_oflag /* output modes */
+		tty->termios.c_oflag /* output modes */
 			&= ~OPOST;    /* disable postprocess output char */
 
-		tty->termios->c_lflag /* line discipline modes */
+		tty->termios.c_lflag /* line discipline modes */
 			&= ~(ECHO     /* disable echo input characters */
 			| ECHONL      /* disable echo new line */
 			| ICANON      /* disable erase, kill, werase, and rprnt
@@ -1200,7 +1200,7 @@
 
 	/* hangup, as defined in acm.c... this might be a bad place for it
 	 * though */
-	if (tty && !(tty->termios->c_cflag & CLOCAL) &&
+	if (tty && !(tty->termios.c_cflag & CLOCAL) &&
 			!(priv->current_status & UART_CD)) {
 		dbg("%s - calling hangup", __func__);
 		tty_hangup(tty);
diff --git a/drivers/usb/serial/digi_acceleport.c b/drivers/usb/serial/digi_acceleport.c
index b5cd838..afd9d2e 100644
--- a/drivers/usb/serial/digi_acceleport.c
+++ b/drivers/usb/serial/digi_acceleport.c
@@ -687,8 +687,8 @@
 		struct usb_serial_port *port, struct ktermios *old_termios)
 {
 	struct digi_port *priv = usb_get_serial_port_data(port);
-	unsigned int iflag = tty->termios->c_iflag;
-	unsigned int cflag = tty->termios->c_cflag;
+	unsigned int iflag = tty->termios.c_iflag;
+	unsigned int cflag = tty->termios.c_cflag;
 	unsigned int old_iflag = old_termios->c_iflag;
 	unsigned int old_cflag = old_termios->c_cflag;
 	unsigned char buf[32];
@@ -709,7 +709,7 @@
 			/* don't set RTS if using hardware flow control */
 			/* and throttling input */
 			modem_signals = TIOCM_DTR;
-			if (!(tty->termios->c_cflag & CRTSCTS) ||
+			if (!(tty->termios.c_cflag & CRTSCTS) ||
 			    !test_bit(TTY_THROTTLED, &tty->flags))
 				modem_signals |= TIOCM_RTS;
 			digi_set_modem_signals(port, modem_signals, 1);
@@ -748,7 +748,7 @@
 		}
 	}
 	/* set parity */
-	tty->termios->c_cflag &= ~CMSPAR;
+	tty->termios.c_cflag &= ~CMSPAR;
 
 	if ((cflag&(PARENB|PARODD)) != (old_cflag&(PARENB|PARODD))) {
 		if (cflag&PARENB) {
@@ -1124,8 +1124,8 @@
 
 	/* set termios settings */
 	if (tty) {
-		not_termios.c_cflag = ~tty->termios->c_cflag;
-		not_termios.c_iflag = ~tty->termios->c_iflag;
+		not_termios.c_cflag = ~tty->termios.c_cflag;
+		not_termios.c_iflag = ~tty->termios.c_iflag;
 		digi_set_termios(tty, port, &not_termios);
 	}
 	return 0;
@@ -1500,7 +1500,7 @@
 
 		rts = 0;
 		if (tty)
-			rts = tty->termios->c_cflag & CRTSCTS;
+			rts = tty->termios.c_cflag & CRTSCTS;
 		
 		if (tty && opcode == DIGI_CMD_READ_INPUT_SIGNALS) {
 			spin_lock(&priv->dp_port_lock);
diff --git a/drivers/usb/serial/empeg.c b/drivers/usb/serial/empeg.c
index cdf61dd..34e8638 100644
--- a/drivers/usb/serial/empeg.c
+++ b/drivers/usb/serial/empeg.c
@@ -87,7 +87,7 @@
 
 static void empeg_init_termios(struct tty_struct *tty)
 {
-	struct ktermios *termios = tty->termios;
+	struct ktermios *termios = &tty->termios;
 
 	/*
 	 * The empeg-car player wants these particular tty settings.
diff --git a/drivers/usb/serial/f81232.c b/drivers/usb/serial/f81232.c
index 499b15f..79451ee 100644
--- a/drivers/usb/serial/f81232.c
+++ b/drivers/usb/serial/f81232.c
@@ -173,10 +173,11 @@
 	/* FIXME - Stubbed out for now */
 
 	/* Don't change anything if nothing has changed */
-	if (!tty_termios_hw_change(tty->termios, old_termios))
+	if (!tty_termios_hw_change(&tty->termios, old_termios))
 		return;
 
 	/* Do the real work here... */
+	tty_termios_copy_hw(&tty->termios, old_termios);
 }
 
 static int f81232_tiocmget(struct tty_struct *tty)
diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c
index 5620db6..24e3e19 100644
--- a/drivers/usb/serial/ftdi_sio.c
+++ b/drivers/usb/serial/ftdi_sio.c
@@ -2082,7 +2082,7 @@
 {
 	struct usb_device *dev = port->serial->dev;
 	struct ftdi_private *priv = usb_get_serial_port_data(port);
-	struct ktermios *termios = tty->termios;
+	struct ktermios *termios = &tty->termios;
 	unsigned int cflag = termios->c_cflag;
 	__u16 urb_value; /* will hold the new flags */
 
diff --git a/drivers/usb/serial/io_edgeport.c b/drivers/usb/serial/io_edgeport.c
index e1f5ccd..f435575 100644
--- a/drivers/usb/serial/io_edgeport.c
+++ b/drivers/usb/serial/io_edgeport.c
@@ -1458,7 +1458,7 @@
 	}
 
 	/* if we are implementing RTS/CTS, toggle that line */
-	if (tty->termios->c_cflag & CRTSCTS) {
+	if (tty->termios.c_cflag & CRTSCTS) {
 		edge_port->shadowMCR &= ~MCR_RTS;
 		status = send_cmd_write_uart_register(edge_port, MCR,
 							edge_port->shadowMCR);
@@ -1497,7 +1497,7 @@
 			return;
 	}
 	/* if we are implementing RTS/CTS, toggle that line */
-	if (tty->termios->c_cflag & CRTSCTS) {
+	if (tty->termios.c_cflag & CRTSCTS) {
 		edge_port->shadowMCR |= MCR_RTS;
 		send_cmd_write_uart_register(edge_port, MCR,
 						edge_port->shadowMCR);
@@ -1516,9 +1516,9 @@
 	struct edgeport_port *edge_port = usb_get_serial_port_data(port);
 	unsigned int cflag;
 
-	cflag = tty->termios->c_cflag;
+	cflag = tty->termios.c_cflag;
 	dbg("%s - clfag %08x iflag %08x", __func__,
-	    tty->termios->c_cflag, tty->termios->c_iflag);
+	    tty->termios.c_cflag, tty->termios.c_iflag);
 	dbg("%s - old clfag %08x old iflag %08x", __func__,
 	    old_termios->c_cflag, old_termios->c_iflag);
 
@@ -1987,7 +1987,7 @@
 		tty = tty_port_tty_get(&edge_port->port->port);
 		if (tty) {
 			change_port_settings(tty,
-				edge_port, tty->termios);
+				edge_port, &tty->termios);
 			tty_kref_put(tty);
 		}
 
@@ -2570,7 +2570,7 @@
 		return;
 	}
 
-	cflag = tty->termios->c_cflag;
+	cflag = tty->termios.c_cflag;
 
 	switch (cflag & CSIZE) {
 	case CS5:
diff --git a/drivers/usb/serial/io_ti.c b/drivers/usb/serial/io_ti.c
index 3936904..765978a 100644
--- a/drivers/usb/serial/io_ti.c
+++ b/drivers/usb/serial/io_ti.c
@@ -1870,7 +1870,7 @@
 
 	/* set up the port settings */
 	if (tty)
-		edge_set_termios(tty, port, tty->termios);
+		edge_set_termios(tty, port, &tty->termios);
 
 	/* open up the port */
 
@@ -2272,13 +2272,13 @@
 
 	config = kmalloc (sizeof (*config), GFP_KERNEL);
 	if (!config) {
-		*tty->termios = *old_termios;
+		tty->termios = *old_termios;
 		dev_err(&edge_port->port->dev, "%s - out of memory\n",
 								__func__);
 		return;
 	}
 
-	cflag = tty->termios->c_cflag;
+	cflag = tty->termios.c_cflag;
 
 	config->wFlags = 0;
 
@@ -2362,7 +2362,7 @@
 	} else
 		dbg("%s - OUTBOUND XON/XOFF is disabled", __func__);
 
-	tty->termios->c_cflag &= ~CMSPAR;
+	tty->termios.c_cflag &= ~CMSPAR;
 
 	/* Round the baud rate */
 	baud = tty_get_baud_rate(tty);
@@ -2408,10 +2408,10 @@
 	struct edgeport_port *edge_port = usb_get_serial_port_data(port);
 	unsigned int cflag;
 
-	cflag = tty->termios->c_cflag;
+	cflag = tty->termios.c_cflag;
 
 	dbg("%s - clfag %08x iflag %08x", __func__,
-	    tty->termios->c_cflag, tty->termios->c_iflag);
+	    tty->termios.c_cflag, tty->termios.c_iflag);
 	dbg("%s - old clfag %08x old iflag %08x", __func__,
 	    old_termios->c_cflag, old_termios->c_iflag);
 	dbg("%s - port %d", __func__, port->number);
diff --git a/drivers/usb/serial/ir-usb.c b/drivers/usb/serial/ir-usb.c
index fc09414..5a96692 100644
--- a/drivers/usb/serial/ir-usb.c
+++ b/drivers/usb/serial/ir-usb.c
@@ -381,7 +381,7 @@
 		ir_xbof = ir_xbof_change(xbof) ;
 
 	/* Only speed changes are supported */
-	tty_termios_copy_hw(tty->termios, old_termios);
+	tty_termios_copy_hw(&tty->termios, old_termios);
 	tty_encode_baud_rate(tty, baud, baud);
 
 	/*
diff --git a/drivers/usb/serial/iuu_phoenix.c b/drivers/usb/serial/iuu_phoenix.c
index 22b1eb5..bf38640 100644
--- a/drivers/usb/serial/iuu_phoenix.c
+++ b/drivers/usb/serial/iuu_phoenix.c
@@ -921,7 +921,7 @@
 {
 	const u32 supported_mask = CMSPAR|PARENB|PARODD;
 	struct iuu_private *priv = usb_get_serial_port_data(port);
-	unsigned int cflag = tty->termios->c_cflag;
+	unsigned int cflag = tty->termios.c_cflag;
 	int status;
 	u32 actual;
 	u32 parity;
@@ -930,7 +930,7 @@
 	u32 newval = cflag & supported_mask;
 
 	/* Just use the ospeed. ispeed should be the same. */
-	baud = tty->termios->c_ospeed;
+	baud = tty->termios.c_ospeed;
 
 	dbg("%s - enter c_ospeed or baud=%d", __func__, baud);
 
@@ -961,13 +961,13 @@
 	 * settings back over and then adjust them
 	 */
 	if (old_termios)
-		tty_termios_copy_hw(tty->termios, old_termios);
+		tty_termios_copy_hw(&tty->termios, old_termios);
 	if (status != 0)	/* Set failed - return old bits */
 		return;
 	/* Re-encode speed, parity and csize */
 	tty_encode_baud_rate(tty, baud, baud);
-	tty->termios->c_cflag &= ~(supported_mask|CSIZE);
-	tty->termios->c_cflag |= newval | csize;
+	tty->termios.c_cflag &= ~(supported_mask|CSIZE);
+	tty->termios.c_cflag |= newval | csize;
 }
 
 static void iuu_close(struct usb_serial_port *port)
@@ -993,14 +993,14 @@
 
 static void iuu_init_termios(struct tty_struct *tty)
 {
-	*(tty->termios) = tty_std_termios;
-	tty->termios->c_cflag = CLOCAL | CREAD | CS8 | B9600
+	tty->termios = tty_std_termios;
+	tty->termios.c_cflag = CLOCAL | CREAD | CS8 | B9600
 				| TIOCM_CTS | CSTOPB | PARENB;
-	tty->termios->c_ispeed = 9600;
-	tty->termios->c_ospeed = 9600;
-	tty->termios->c_lflag = 0;
-	tty->termios->c_oflag = 0;
-	tty->termios->c_iflag = 0;
+	tty->termios.c_ispeed = 9600;
+	tty->termios.c_ospeed = 9600;
+	tty->termios.c_lflag = 0;
+	tty->termios.c_oflag = 0;
+	tty->termios.c_iflag = 0;
 }
 
 static int iuu_open(struct tty_struct *tty, struct usb_serial_port *port)
@@ -1012,8 +1012,8 @@
 	u32 actual;
 	struct iuu_private *priv = usb_get_serial_port_data(port);
 
-	baud = tty->termios->c_ospeed;
-	tty->termios->c_ispeed = baud;
+	baud = tty->termios.c_ospeed;
+	tty->termios.c_ispeed = baud;
 	/* Re-encode speed */
 	tty_encode_baud_rate(tty, baud, baud);
 
diff --git a/drivers/usb/serial/keyspan.c b/drivers/usb/serial/keyspan.c
index af0b70e..7bcbb47 100644
--- a/drivers/usb/serial/keyspan.c
+++ b/drivers/usb/serial/keyspan.c
@@ -158,7 +158,7 @@
 
 	p_priv = usb_get_serial_port_data(port);
 	d_details = p_priv->device_details;
-	cflag = tty->termios->c_cflag;
+	cflag = tty->termios.c_cflag;
 	device_port = port->number - port->serial->minor;
 
 	/* Baud rate calculation takes baud rate as an integer
@@ -179,7 +179,7 @@
 	p_priv->flow_control = (cflag & CRTSCTS) ? flow_cts : flow_none;
 
 	/* Mark/Space not supported */
-	tty->termios->c_cflag &= ~CMSPAR;
+	tty->termios.c_cflag &= ~CMSPAR;
 
 	keyspan_send_setup(port, 0);
 }
@@ -1086,7 +1086,7 @@
 
 	device_port = port->number - port->serial->minor;
 	if (tty) {
-		cflag = tty->termios->c_cflag;
+		cflag = tty->termios.c_cflag;
 		/* Baud rate calculation takes baud rate as an integer
 		   so other rates can be generated if desired. */
 		baud_rate = tty_get_baud_rate(tty);
diff --git a/drivers/usb/serial/keyspan_pda.c b/drivers/usb/serial/keyspan_pda.c
index a4ac3cf..dcada86 100644
--- a/drivers/usb/serial/keyspan_pda.c
+++ b/drivers/usb/serial/keyspan_pda.c
@@ -338,7 +338,7 @@
 	   7[EOMS]1: 10 bit, b0/b7 is parity
 	   7[EOMS]2: 11 bit, b0/b7 is parity, extra bit always (mark?)
 
-	   HW flow control is dictated by the tty->termios->c_cflags & CRTSCTS
+	   HW flow control is dictated by the tty->termios.c_cflags & CRTSCTS
 	   bit.
 
 	   For now, just do baud. */
@@ -353,7 +353,7 @@
 	}
 	/* Only speed can change so copy the old h/w parameters
 	   then encode the new speed */
-	tty_termios_copy_hw(tty->termios, old_termios);
+	tty_termios_copy_hw(&tty->termios, old_termios);
 	tty_encode_baud_rate(tty, speed, speed);
 }
 
diff --git a/drivers/usb/serial/kl5kusb105.c b/drivers/usb/serial/kl5kusb105.c
index 5bed59c..def9ad2 100644
--- a/drivers/usb/serial/kl5kusb105.c
+++ b/drivers/usb/serial/kl5kusb105.c
@@ -311,12 +311,12 @@
 
 	/* set up termios structure */
 	spin_lock_irqsave(&priv->lock, flags);
-	priv->termios.c_iflag = tty->termios->c_iflag;
-	priv->termios.c_oflag = tty->termios->c_oflag;
-	priv->termios.c_cflag = tty->termios->c_cflag;
-	priv->termios.c_lflag = tty->termios->c_lflag;
+	priv->termios.c_iflag = tty->termios.c_iflag;
+	priv->termios.c_oflag = tty->termios.c_oflag;
+	priv->termios.c_cflag = tty->termios.c_cflag;
+	priv->termios.c_lflag = tty->termios.c_lflag;
 	for (i = 0; i < NCCS; i++)
-		priv->termios.c_cc[i] = tty->termios->c_cc[i];
+		priv->termios.c_cc[i] = tty->termios.c_cc[i];
 	priv->cfg.pktlen   = cfg->pktlen;
 	priv->cfg.baudrate = cfg->baudrate;
 	priv->cfg.databits = cfg->databits;
@@ -445,9 +445,9 @@
 				 struct ktermios *old_termios)
 {
 	struct klsi_105_private *priv = usb_get_serial_port_data(port);
-	unsigned int iflag = tty->termios->c_iflag;
+	unsigned int iflag = tty->termios.c_iflag;
 	unsigned int old_iflag = old_termios->c_iflag;
-	unsigned int cflag = tty->termios->c_cflag;
+	unsigned int cflag = tty->termios.c_cflag;
 	unsigned int old_cflag = old_termios->c_cflag;
 	struct klsi_105_port_settings *cfg;
 	unsigned long flags;
@@ -560,7 +560,7 @@
 	if ((cflag & (PARENB|PARODD)) != (old_cflag & (PARENB|PARODD))
 	    || (cflag & CSTOPB) != (old_cflag & CSTOPB)) {
 		/* Not currently supported */
-		tty->termios->c_cflag &= ~(PARENB|PARODD|CSTOPB);
+		tty->termios.c_cflag &= ~(PARENB|PARODD|CSTOPB);
 #if 0
 		priv->last_lcr = 0;
 
@@ -587,7 +587,7 @@
 	    || (iflag & IXON) != (old_iflag & IXON)
 	    ||  (cflag & CRTSCTS) != (old_cflag & CRTSCTS)) {
 		/* Not currently supported */
-		tty->termios->c_cflag &= ~CRTSCTS;
+		tty->termios.c_cflag &= ~CRTSCTS;
 		/* Drop DTR/RTS if no flow control otherwise assert */
 #if 0
 		if ((iflag & IXOFF) || (iflag & IXON) || (cflag & CRTSCTS))
diff --git a/drivers/usb/serial/kobil_sct.c b/drivers/usb/serial/kobil_sct.c
index fafeabb..bf5c749 100644
--- a/drivers/usb/serial/kobil_sct.c
+++ b/drivers/usb/serial/kobil_sct.c
@@ -191,11 +191,11 @@
 static void kobil_init_termios(struct tty_struct *tty)
 {
 	/* Default to echo off and other sane device settings */
-	tty->termios->c_lflag = 0;
-	tty->termios->c_lflag &= ~(ISIG | ICANON | ECHO | IEXTEN | XCASE);
-	tty->termios->c_iflag = IGNBRK | IGNPAR | IXOFF;
+	tty->termios.c_lflag = 0;
+	tty->termios.c_iflag &= ~(ISIG | ICANON | ECHO | IEXTEN | XCASE);
+	tty->termios.c_iflag |= IGNBRK | IGNPAR | IXOFF;
 	/* do NOT translate CR to CR-NL (0x0A -> 0x0A 0x0D) */
-	tty->termios->c_oflag &= ~ONLCR;
+	tty->termios.c_oflag &= ~ONLCR;
 }
 
 static int kobil_open(struct tty_struct *tty, struct usb_serial_port *port)
@@ -581,14 +581,14 @@
 	struct kobil_private *priv;
 	int result;
 	unsigned short urb_val = 0;
-	int c_cflag = tty->termios->c_cflag;
+	int c_cflag = tty->termios.c_cflag;
 	speed_t speed;
 
 	priv = usb_get_serial_port_data(port);
 	if (priv->device_type == KOBIL_USBTWIN_PRODUCT_ID ||
 			priv->device_type == KOBIL_KAAN_SIM_PRODUCT_ID) {
 		/* This device doesn't support ioctl calls */
-		*tty->termios = *old;
+		tty_termios_copy_hw(&tty->termios, old);
 		return;
 	}
 
@@ -612,7 +612,7 @@
 			urb_val |= SUSBCR_SPASB_EvenParity;
 	} else
 		urb_val |= SUSBCR_SPASB_NoParity;
-	tty->termios->c_cflag &= ~CMSPAR;
+	tty->termios.c_cflag &= ~CMSPAR;
 	tty_encode_baud_rate(tty, speed, speed);
 
 	result = usb_control_msg(port->serial->dev,
diff --git a/drivers/usb/serial/mct_u232.c b/drivers/usb/serial/mct_u232.c
index a71fa0a..df98cff 100644
--- a/drivers/usb/serial/mct_u232.c
+++ b/drivers/usb/serial/mct_u232.c
@@ -454,7 +454,7 @@
 	 * either.
 	 */
 	spin_lock_irqsave(&priv->lock, flags);
-	if (tty && (tty->termios->c_cflag & CBAUD))
+	if (tty && (tty->termios.c_cflag & CBAUD))
 		priv->control_state = TIOCM_DTR | TIOCM_RTS;
 	else
 		priv->control_state = 0;
@@ -634,7 +634,7 @@
 {
 	struct usb_serial *serial = port->serial;
 	struct mct_u232_private *priv = usb_get_serial_port_data(port);
-	struct ktermios *termios = tty->termios;
+	struct ktermios *termios = &tty->termios;
 	unsigned int cflag = termios->c_cflag;
 	unsigned int old_cflag = old_termios->c_cflag;
 	unsigned long flags;
diff --git a/drivers/usb/serial/metro-usb.c b/drivers/usb/serial/metro-usb.c
index d47eb06..2b0627b 100644
--- a/drivers/usb/serial/metro-usb.c
+++ b/drivers/usb/serial/metro-usb.c
@@ -130,12 +130,6 @@
 
 	/* Set the data read from the usb port into the serial port buffer. */
 	tty = tty_port_tty_get(&port->port);
-	if (!tty) {
-		dev_err(&port->dev, "%s - bad tty pointer - exiting\n",
-			__func__);
-		return;
-	}
-
 	if (tty && urb->actual_length) {
 		/* Loop through the data copying each byte to the tty layer. */
 		tty_insert_flip_string(tty, data, urb->actual_length);
diff --git a/drivers/usb/serial/mos7720.c b/drivers/usb/serial/mos7720.c
index a07dd3c..012f67b 100644
--- a/drivers/usb/serial/mos7720.c
+++ b/drivers/usb/serial/mos7720.c
@@ -1349,7 +1349,7 @@
 	}
 
 	/* if we are implementing RTS/CTS, toggle that line */
-	if (tty->termios->c_cflag & CRTSCTS) {
+	if (tty->termios.c_cflag & CRTSCTS) {
 		mos7720_port->shadowMCR &= ~UART_MCR_RTS;
 		write_mos_reg(port->serial, port->number - port->serial->minor,
 			      MCR, mos7720_port->shadowMCR);
@@ -1383,7 +1383,7 @@
 	}
 
 	/* if we are implementing RTS/CTS, toggle that line */
-	if (tty->termios->c_cflag & CRTSCTS) {
+	if (tty->termios.c_cflag & CRTSCTS) {
 		mos7720_port->shadowMCR |= UART_MCR_RTS;
 		write_mos_reg(port->serial, port->number - port->serial->minor,
 			      MCR, mos7720_port->shadowMCR);
@@ -1604,8 +1604,8 @@
 	lStop = 0x00;	/* 1 stop bit */
 	lParity = 0x00;	/* No parity */
 
-	cflag = tty->termios->c_cflag;
-	iflag = tty->termios->c_iflag;
+	cflag = tty->termios.c_cflag;
+	iflag = tty->termios.c_iflag;
 
 	/* Change the number of bits */
 	switch (cflag & CSIZE) {
@@ -1753,11 +1753,11 @@
 
 	dbg("%s\n", "setting termios - ASPIRE");
 
-	cflag = tty->termios->c_cflag;
+	cflag = tty->termios.c_cflag;
 
 	dbg("%s - cflag %08x iflag %08x", __func__,
-	    tty->termios->c_cflag,
-	    RELEVANT_IFLAG(tty->termios->c_iflag));
+	    tty->termios.c_cflag,
+	    RELEVANT_IFLAG(tty->termios.c_iflag));
 
 	dbg("%s - old cflag %08x old iflag %08x", __func__,
 	    old_termios->c_cflag,
diff --git a/drivers/usb/serial/mos7840.c b/drivers/usb/serial/mos7840.c
index 2f6da1e..402c32d 100644
--- a/drivers/usb/serial/mos7840.c
+++ b/drivers/usb/serial/mos7840.c
@@ -1651,7 +1651,7 @@
 			return;
 	}
 	/* if we are implementing RTS/CTS, toggle that line */
-	if (tty->termios->c_cflag & CRTSCTS) {
+	if (tty->termios.c_cflag & CRTSCTS) {
 		mos7840_port->shadowMCR &= ~MCR_RTS;
 		status = mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER,
 					 mos7840_port->shadowMCR);
@@ -1694,7 +1694,7 @@
 	}
 
 	/* if we are implementing RTS/CTS, toggle that line */
-	if (tty->termios->c_cflag & CRTSCTS) {
+	if (tty->termios.c_cflag & CRTSCTS) {
 		mos7840_port->shadowMCR |= MCR_RTS;
 		status = mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER,
 					 mos7840_port->shadowMCR);
@@ -2000,8 +2000,8 @@
 	lStop = LCR_STOP_1;
 	lParity = LCR_PAR_NONE;
 
-	cflag = tty->termios->c_cflag;
-	iflag = tty->termios->c_iflag;
+	cflag = tty->termios.c_cflag;
+	iflag = tty->termios.c_iflag;
 
 	/* Change the number of bits */
 	if (cflag & CSIZE) {
@@ -2161,10 +2161,10 @@
 
 	dbg("%s", "setting termios - ");
 
-	cflag = tty->termios->c_cflag;
+	cflag = tty->termios.c_cflag;
 
 	dbg("%s - clfag %08x iflag %08x", __func__,
-	    tty->termios->c_cflag, RELEVANT_IFLAG(tty->termios->c_iflag));
+	    tty->termios.c_cflag, RELEVANT_IFLAG(tty->termios.c_iflag));
 	dbg("%s - old clfag %08x old iflag %08x", __func__,
 	    old_termios->c_cflag, RELEVANT_IFLAG(old_termios->c_iflag));
 	dbg("%s - port %d", __func__, port->number);
diff --git a/drivers/usb/serial/oti6858.c b/drivers/usb/serial/oti6858.c
index 5976b65..9f55556 100644
--- a/drivers/usb/serial/oti6858.c
+++ b/drivers/usb/serial/oti6858.c
@@ -404,10 +404,10 @@
 
 static void oti6858_init_termios(struct tty_struct *tty)
 {
-	*(tty->termios) = tty_std_termios;
-	tty->termios->c_cflag = B38400 | CS8 | CREAD | HUPCL | CLOCAL;
-	tty->termios->c_ispeed = 38400;
-	tty->termios->c_ospeed = 38400;
+	tty->termios = tty_std_termios;
+	tty->termios.c_cflag = B38400 | CS8 | CREAD | HUPCL | CLOCAL;
+	tty->termios.c_ispeed = 38400;
+	tty->termios.c_ospeed = 38400;
 }
 
 static void oti6858_set_termios(struct tty_struct *tty,
@@ -425,7 +425,7 @@
 		return;
 	}
 
-	cflag = tty->termios->c_cflag;
+	cflag = tty->termios.c_cflag;
 
 	spin_lock_irqsave(&priv->lock, flags);
 	divisor = priv->pending_setup.divisor;
diff --git a/drivers/usb/serial/pl2303.c b/drivers/usb/serial/pl2303.c
index 13b8dd6..2b9108a 100644
--- a/drivers/usb/serial/pl2303.c
+++ b/drivers/usb/serial/pl2303.c
@@ -260,16 +260,16 @@
 	   serial settings even to the same values as before. Thus
 	   we actually need to filter in this specific case */
 
-	if (!tty_termios_hw_change(tty->termios, old_termios))
+	if (!tty_termios_hw_change(&tty->termios, old_termios))
 		return;
 
-	cflag = tty->termios->c_cflag;
+	cflag = tty->termios.c_cflag;
 
 	buf = kzalloc(7, GFP_KERNEL);
 	if (!buf) {
 		dev_err(&port->dev, "%s - out of memory.\n", __func__);
 		/* Report back no change occurred */
-		*tty->termios = *old_termios;
+		tty->termios = *old_termios;
 		return;
 	}
 
diff --git a/drivers/usb/serial/quatech2.c b/drivers/usb/serial/quatech2.c
index 151670b..7df9cdb 100644
--- a/drivers/usb/serial/quatech2.c
+++ b/drivers/usb/serial/quatech2.c
@@ -275,7 +275,7 @@
 {
 	struct usb_device *dev = port->serial->dev;
 	struct qt2_port_private *port_priv;
-	struct ktermios *termios = tty->termios;
+	struct ktermios *termios = &tty->termios;
 	u16 baud;
 	unsigned int cflag = termios->c_cflag;
 	u16 new_lcr = 0;
@@ -406,7 +406,7 @@
 	port_priv->device_port = (u8) device_port;
 
 	if (tty)
-		qt2_set_termios(tty, port, tty->termios);
+		qt2_set_termios(tty, port, &tty->termios);
 
 	return 0;
 
diff --git a/drivers/usb/serial/sierra.c b/drivers/usb/serial/sierra.c
index 0274710..b14ebbd 100644
--- a/drivers/usb/serial/sierra.c
+++ b/drivers/usb/serial/sierra.c
@@ -382,7 +382,7 @@
 static void sierra_set_termios(struct tty_struct *tty,
 		struct usb_serial_port *port, struct ktermios *old_termios)
 {
-	tty_termios_copy_hw(tty->termios, old_termios);
+	tty_termios_copy_hw(&tty->termios, old_termios);
 	sierra_send_setup(port);
 }
 
diff --git a/drivers/usb/serial/spcp8x5.c b/drivers/usb/serial/spcp8x5.c
index cad6089..ab68a4d 100644
--- a/drivers/usb/serial/spcp8x5.c
+++ b/drivers/usb/serial/spcp8x5.c
@@ -316,10 +316,10 @@
 static void spcp8x5_init_termios(struct tty_struct *tty)
 {
 	/* for the 1st time call this function */
-	*(tty->termios) = tty_std_termios;
-	tty->termios->c_cflag = B115200 | CS8 | CREAD | HUPCL | CLOCAL;
-	tty->termios->c_ispeed = 115200;
-	tty->termios->c_ospeed = 115200;
+	tty->termios = tty_std_termios;
+	tty->termios.c_cflag = B115200 | CS8 | CREAD | HUPCL | CLOCAL;
+	tty->termios.c_ispeed = 115200;
+	tty->termios.c_ospeed = 115200;
 }
 
 /* set the serial param for transfer. we should check if we really need to
@@ -330,7 +330,7 @@
 	struct usb_serial *serial = port->serial;
 	struct spcp8x5_private *priv = usb_get_serial_port_data(port);
 	unsigned long flags;
-	unsigned int cflag = tty->termios->c_cflag;
+	unsigned int cflag = tty->termios.c_cflag;
 	unsigned int old_cflag = old_termios->c_cflag;
 	unsigned short uartdata;
 	unsigned char buf[2] = {0, 0};
@@ -340,7 +340,7 @@
 
 
 	/* check that they really want us to change something */
-	if (!tty_termios_hw_change(tty->termios, old_termios))
+	if (!tty_termios_hw_change(&tty->termios, old_termios))
 		return;
 
 	/* set DTR/RTS active */
diff --git a/drivers/usb/serial/ssu100.c b/drivers/usb/serial/ssu100.c
index 3fee23b..cf2d30c 100644
--- a/drivers/usb/serial/ssu100.c
+++ b/drivers/usb/serial/ssu100.c
@@ -216,7 +216,7 @@
 			       struct ktermios *old_termios)
 {
 	struct usb_device *dev = port->serial->dev;
-	struct ktermios *termios = tty->termios;
+	struct ktermios *termios = &tty->termios;
 	u16 baud, divisor, remainder;
 	unsigned int cflag = termios->c_cflag;
 	u16 urb_value = 0; /* will hold the new flags */
@@ -322,7 +322,7 @@
 		dbg("%s - set uart failed", __func__);
 
 	if (tty)
-		ssu100_set_termios(tty, port, tty->termios);
+		ssu100_set_termios(tty, port, &tty->termios);
 
 	return usb_serial_generic_open(tty, port);
 }
diff --git a/drivers/usb/serial/ti_usb_3410_5052.c b/drivers/usb/serial/ti_usb_3410_5052.c
index a4404f5..f502a16 100644
--- a/drivers/usb/serial/ti_usb_3410_5052.c
+++ b/drivers/usb/serial/ti_usb_3410_5052.c
@@ -520,7 +520,7 @@
 	}
 
 	if (tty)
-		ti_set_termios(tty, port, tty->termios);
+		ti_set_termios(tty, port, &tty->termios);
 
 	dbg("%s - sending TI_OPEN_PORT", __func__);
 	status = ti_command_out_sync(tdev, TI_OPEN_PORT,
@@ -562,7 +562,7 @@
 	usb_clear_halt(dev, port->read_urb->pipe);
 
 	if (tty)
-		ti_set_termios(tty, port, tty->termios);
+		ti_set_termios(tty, port, &tty->termios);
 
 	dbg("%s - sending TI_OPEN_PORT (2)", __func__);
 	status = ti_command_out_sync(tdev, TI_OPEN_PORT,
@@ -831,8 +831,8 @@
 	int port_number = port->number - port->serial->minor;
 	unsigned int mcr;
 
-	cflag = tty->termios->c_cflag;
-	iflag = tty->termios->c_iflag;
+	cflag = tty->termios.c_cflag;
+	iflag = tty->termios.c_iflag;
 
 	dbg("%s - cflag %08x, iflag %08x", __func__, cflag, iflag);
 	dbg("%s - old clfag %08x, old iflag %08x", __func__,
@@ -871,7 +871,7 @@
 	}
 
 	/* CMSPAR isn't supported by this driver */
-	tty->termios->c_cflag &= ~CMSPAR;
+	tty->termios.c_cflag &= ~CMSPAR;
 
 	if (cflag & PARENB) {
 		if (cflag & PARODD) {
diff --git a/drivers/usb/serial/usb-serial.c b/drivers/usb/serial/usb-serial.c
index 27483f9..aa4b0d7 100644
--- a/drivers/usb/serial/usb-serial.c
+++ b/drivers/usb/serial/usb-serial.c
@@ -207,7 +207,7 @@
 	if (retval)
 		goto error_get_interface;
 
-	retval = tty_standard_install(driver, tty);
+	retval = tty_port_install(&port->port, driver, tty);
 	if (retval)
 		goto error_init_termios;
 
@@ -305,8 +305,7 @@
  * Do the resource freeing and refcount dropping for the port.
  * Avoid freeing the console.
  *
- * Called asynchronously after the last tty kref is dropped,
- * and the tty layer has already done the tty_shutdown(tty);
+ * Called asynchronously after the last tty kref is dropped.
  */
 static void serial_cleanup(struct tty_struct *tty)
 {
@@ -423,7 +422,7 @@
 	if (port->serial->type->set_termios)
 		port->serial->type->set_termios(tty, port, old);
 	else
-		tty_termios_copy_hw(tty->termios, old);
+		tty_termios_copy_hw(&tty->termios, old);
 }
 
 static int serial_break(struct tty_struct *tty, int break_state)
diff --git a/drivers/usb/serial/usb_wwan.c b/drivers/usb/serial/usb_wwan.c
index 6855d5e..72b678d 100644
--- a/drivers/usb/serial/usb_wwan.c
+++ b/drivers/usb/serial/usb_wwan.c
@@ -67,7 +67,7 @@
 	struct usb_wwan_intf_private *intfdata = port->serial->private;
 
 	/* Doesn't support option setting */
-	tty_termios_copy_hw(tty->termios, old_termios);
+	tty_termios_copy_hw(&tty->termios, old_termios);
 
 	if (intfdata->send_setup)
 		intfdata->send_setup(port);
diff --git a/drivers/usb/serial/whiteheat.c b/drivers/usb/serial/whiteheat.c
index 473635e..b36077d 100644
--- a/drivers/usb/serial/whiteheat.c
+++ b/drivers/usb/serial/whiteheat.c
@@ -724,7 +724,7 @@
 {
 	struct usb_serial_port *port = tty->driver_data;
 	struct whiteheat_port_settings port_settings;
-	unsigned int cflag = tty->termios->c_cflag;
+	unsigned int cflag = tty->termios.c_cflag;
 
 	port_settings.port = port->number + 1;
 
diff --git a/drivers/video/auo_k190x.c b/drivers/video/auo_k190x.c
index 77da6a2..c03ecdd 100644
--- a/drivers/video/auo_k190x.c
+++ b/drivers/video/auo_k190x.c
@@ -987,7 +987,6 @@
 	fb_dealloc_cmap(&info->cmap);
 err_cmap:
 	fb_deferred_io_cleanup(info);
-	kfree(info->fbdefio);
 err_defio:
 	vfree((void *)info->screen_base);
 err_irq:
@@ -1022,7 +1021,6 @@
 	fb_dealloc_cmap(&info->cmap);
 
 	fb_deferred_io_cleanup(info);
-	kfree(info->fbdefio);
 
 	vfree((void *)info->screen_base);
 
diff --git a/drivers/video/backlight/omap1_bl.c b/drivers/video/backlight/omap1_bl.c
index bfdc5fb..92257ef 100644
--- a/drivers/video/backlight/omap1_bl.c
+++ b/drivers/video/backlight/omap1_bl.c
@@ -27,9 +27,9 @@
 #include <linux/fb.h>
 #include <linux/backlight.h>
 #include <linux/slab.h>
+#include <linux/platform_data/omap1_bl.h>
 
 #include <mach/hardware.h>
-#include <plat/board.h>
 #include <plat/mux.h>
 
 #define OMAPBL_MAX_INTENSITY		0xff
diff --git a/drivers/video/console/bitblit.c b/drivers/video/console/bitblit.c
index 28b1a83..61b182b 100644
--- a/drivers/video/console/bitblit.c
+++ b/drivers/video/console/bitblit.c
@@ -162,7 +162,7 @@
 	image.depth = 1;
 
 	if (attribute) {
-		buf = kmalloc(cellsize, GFP_KERNEL);
+		buf = kmalloc(cellsize, GFP_ATOMIC);
 		if (!buf)
 			return;
 	}
diff --git a/drivers/video/console/fbcon.c b/drivers/video/console/fbcon.c
index 88e9204..fdefa8f 100644
--- a/drivers/video/console/fbcon.c
+++ b/drivers/video/console/fbcon.c
@@ -449,7 +449,7 @@
 
 	while ((options = strsep(&this_opt, ",")) != NULL) {
 		if (!strncmp(options, "font:", 5))
-			strcpy(fontname, options + 5);
+			strlcpy(fontname, options + 5, sizeof(fontname));
 		
 		if (!strncmp(options, "scrollback:", 11)) {
 			options += 11;
diff --git a/drivers/video/mb862xx/mb862xxfbdrv.c b/drivers/video/mb862xx/mb862xxfbdrv.c
index 00ce1f3..57d940b 100644
--- a/drivers/video/mb862xx/mb862xxfbdrv.c
+++ b/drivers/video/mb862xx/mb862xxfbdrv.c
@@ -328,6 +328,8 @@
 	case MB862XX_L1_SET_CFG:
 		if (copy_from_user(l1_cfg, argp, sizeof(*l1_cfg)))
 			return -EFAULT;
+		if (l1_cfg->dh == 0 || l1_cfg->dw == 0)
+			return -EINVAL;
 		if ((l1_cfg->sw >= l1_cfg->dw) && (l1_cfg->sh >= l1_cfg->dh)) {
 			/* downscaling */
 			outreg(cap, GC_CAP_CSC,
diff --git a/drivers/video/omap2/dss/sdi.c b/drivers/video/omap2/dss/sdi.c
index 5d31699..f43bfe1 100644
--- a/drivers/video/omap2/dss/sdi.c
+++ b/drivers/video/omap2/dss/sdi.c
@@ -105,6 +105,20 @@
 
 	sdi_config_lcd_manager(dssdev);
 
+	/*
+	 * LCLK and PCLK divisors are located in shadow registers, and we
+	 * normally write them to DISPC registers when enabling the output.
+	 * However, SDI uses pck-free as source clock for its PLL, and pck-free
+	 * is affected by the divisors. And as we need the PLL before enabling
+	 * the output, we need to write the divisors early.
+	 *
+	 * It seems just writing to the DISPC register is enough, and we don't
+	 * need to care about the shadow register mechanism for pck-free. The
+	 * exact reason for this is unknown.
+	 */
+	dispc_mgr_set_clock_div(dssdev->manager->id,
+			&sdi.mgr_config.clock_info);
+
 	dss_sdi_init(dssdev->phy.sdi.datapairs);
 	r = dss_sdi_enable();
 	if (r)
diff --git a/drivers/video/omap2/omapfb/omapfb-main.c b/drivers/video/omap2/omapfb/omapfb-main.c
index 08ec1a7..fc671d3 100644
--- a/drivers/video/omap2/omapfb/omapfb-main.c
+++ b/drivers/video/omap2/omapfb/omapfb-main.c
@@ -1192,7 +1192,7 @@
 			break;
 
 		if (regno < 16) {
-			u16 pal;
+			u32 pal;
 			pal = ((red >> (16 - var->red.length)) <<
 					var->red.offset) |
 				((green >> (16 - var->green.length)) <<
diff --git a/drivers/watchdog/booke_wdt.c b/drivers/watchdog/booke_wdt.c
index 3fe82d0..5b06d31 100644
--- a/drivers/watchdog/booke_wdt.c
+++ b/drivers/watchdog/booke_wdt.c
@@ -166,18 +166,17 @@
 
 	switch (cmd) {
 	case WDIOC_GETSUPPORT:
-		if (copy_to_user((void *)arg, &ident, sizeof(ident)))
-			return -EFAULT;
+		return copy_to_user(p, &ident, sizeof(ident)) ? -EFAULT : 0;
 	case WDIOC_GETSTATUS:
 		return put_user(0, p);
 	case WDIOC_GETBOOTSTATUS:
 		/* XXX: something is clearing TSR */
 		tmp = mfspr(SPRN_TSR) & TSR_WRS(3);
 		/* returns CARDRESET if last reset was caused by the WDT */
-		return (tmp ? WDIOF_CARDRESET : 0);
+		return put_user((tmp ? WDIOF_CARDRESET : 0), p);
 	case WDIOC_SETOPTIONS:
 		if (get_user(tmp, p))
-			return -EINVAL;
+			return -EFAULT;
 		if (tmp == WDIOS_ENABLECARD) {
 			booke_wdt_ping();
 			break;
diff --git a/drivers/watchdog/da9052_wdt.c b/drivers/watchdog/da9052_wdt.c
index 3f75129..f7abbae 100644
--- a/drivers/watchdog/da9052_wdt.c
+++ b/drivers/watchdog/da9052_wdt.c
@@ -21,7 +21,6 @@
 #include <linux/types.h>
 #include <linux/kernel.h>
 #include <linux/jiffies.h>
-#include <linux/delay.h>
 
 #include <linux/mfd/da9052/reg.h>
 #include <linux/mfd/da9052/da9052.h>
diff --git a/drivers/xen/platform-pci.c b/drivers/xen/platform-pci.c
index d4c50d6..97ca359 100644
--- a/drivers/xen/platform-pci.c
+++ b/drivers/xen/platform-pci.c
@@ -101,19 +101,6 @@
 	return 0;
 }
 
-static void __devinit prepare_shared_info(void)
-{
-#ifdef CONFIG_KEXEC
-	unsigned long addr;
-	struct shared_info *hvm_shared_info;
-
-	addr = alloc_xen_mmio(PAGE_SIZE);
-	hvm_shared_info = ioremap(addr, PAGE_SIZE);
-	memset(hvm_shared_info, 0, PAGE_SIZE);
-	xen_hvm_prepare_kexec(hvm_shared_info, addr >> PAGE_SHIFT);
-#endif
-}
-
 static int __devinit platform_pci_init(struct pci_dev *pdev,
 				       const struct pci_device_id *ent)
 {
@@ -151,8 +138,6 @@
 	platform_mmio = mmio_addr;
 	platform_mmiolen = mmio_len;
 
-	prepare_shared_info();
-
 	if (!xen_have_vector_callback) {
 		ret = xen_allocate_irq(pdev);
 		if (ret) {
diff --git a/drivers/xen/swiotlb-xen.c b/drivers/xen/swiotlb-xen.c
index 1afb4fb..4d51948 100644
--- a/drivers/xen/swiotlb-xen.c
+++ b/drivers/xen/swiotlb-xen.c
@@ -232,7 +232,7 @@
 		return ret;
 
 	if (hwdev && hwdev->coherent_dma_mask)
-		dma_mask = hwdev->coherent_dma_mask;
+		dma_mask = dma_alloc_coherent_mask(hwdev, flags);
 
 	phys = virt_to_phys(ret);
 	dev_addr = xen_phys_to_bus(phys);
diff --git a/drivers/xen/xen-pciback/pci_stub.c b/drivers/xen/xen-pciback/pci_stub.c
index 097e536..0334272 100644
--- a/drivers/xen/xen-pciback/pci_stub.c
+++ b/drivers/xen/xen-pciback/pci_stub.c
@@ -353,16 +353,16 @@
 	if (err)
 		goto config_release;
 
-	dev_dbg(&dev->dev, "reseting (FLR, D3, etc) the device\n");
-	__pci_reset_function_locked(dev);
-
 	/* We need the device active to save the state. */
 	dev_dbg(&dev->dev, "save state of device\n");
 	pci_save_state(dev);
 	dev_data->pci_saved_state = pci_store_saved_state(dev);
 	if (!dev_data->pci_saved_state)
 		dev_err(&dev->dev, "Could not store PCI conf saved state!\n");
-
+	else {
+		dev_dbg(&dev->dev, "reseting (FLR, D3, etc) the device\n");
+		__pci_reset_function_locked(dev);
+	}
 	/* Now disable the device (this also ensures some private device
 	 * data is setup before we export)
 	 */
diff --git a/firmware/Makefile b/firmware/Makefile
index 344713b..fdc9ff0 100644
--- a/firmware/Makefile
+++ b/firmware/Makefile
@@ -40,7 +40,6 @@
 			     bnx2/bnx2-mips-06-6.2.1.fw \
 			     bnx2/bnx2-rv2p-06-6.0.15.fw
 fw-shipped-$(CONFIG_CASSINI) += sun/cassini.bin
-fw-shipped-$(CONFIG_COMPUTONE) += intelliport2.bin
 fw-shipped-$(CONFIG_CHELSIO_T3) += cxgb3/t3b_psram-1.1.0.bin \
 				   cxgb3/t3c_psram-1.1.0.bin \
 				   cxgb3/t3fw-7.10.0.bin \
diff --git a/firmware/intelliport2.bin.ihex b/firmware/intelliport2.bin.ihex
deleted file mode 100644
index e9cfe8c..0000000
--- a/firmware/intelliport2.bin.ihex
+++ /dev/null
@@ -1,2147 +0,0 @@
-:100000003C4237180201030000000000000000001D
-:10001000576564204465632030312031323A3234F0
-:100020003A33302031393939000000000000000037
-:10003000E96C0F426547694E6E496E47206F462056
-:10004000634F6445CC135A15E8167618041A921BB0
-:10005000201DAE1E3C20CA215823E6247426022807
-:1000600090291E2BAC2C3A2EC82F5631E432723414
-:1000700000368E371C39AA3A383CC63D543FE24020
-:100080007042FE438C451A47A848364AC44B524D2D
-:10009000E04E6E50FC518A531855A6563458C2593A
-:1000A000505BDE5C6C5EFA5F88611663A464326646
-:1000B000C0674E69DC6A6A6CF86D866F1471A27253
-:1000C0003074BE754C776C778C77AC7733DB8ADC19
-:1000D0005333DB250700750A8A1E080183E30CEB06
-:1000E00020903C01750A8A1E080180E3C0EB129043
-:1000F0008A1E0D013C02750680E30CEB049080E340
-:10010000C053508B1EBA138EDBE86A65558BEC53D7
-:100110001E2BC08ED88B5E04C1E304035E06D1E3C0
-:100120002E8B9F44008D472A1E5A1F5B5DC3558B43
-:10013000EC531E2BC08ED88B5E04C1E304035E0615
-:10014000D1E32E8B9F44008D47341E5A1F5B5DC345
-:10015000FB558BEC53515256571E061E0733C08E6B
-:10016000D88B5E04268A47592503008BF0D1E62EF2
-:100170008BB4C400C1E0042602471AD1E08BE82EFC
-:100180008BAE4400892C268A471C88440F268A4758
-:100190001D884410268A471E884411268A471F88D6
-:1001A0004412268A4720884413268A472388441409
-:1001B000268A4724884415268A475A88440E33C025
-:1001C00089440689440888440B88440AB021B464F1
-:1001D000894404894402B05588440D88440CE86A77
-:1001E00000725BE8C900E8C110894408807C0F01F7
-:1001F0007429E82B02E87F02807C0F03741DE8A9B4
-:10020000108BF82B44083DA00F7210897C0833C076
-:1002100087440685C07504C6440AFF8A440A84C020
-:10022000750BB80800E86A4AE8A90173BFE84F01F6
-:100230008166487FFF83667ABFB002E8040E8A4475
-:100240000A98071F5F5E5A595B5DC3814E48800064
-:10025000B040E83D4AE88940732AE84D108BD8B099
-:1002600005E82E4AF6462702751AE83D102BC33DD5
-:10027000581B72EB8166487FFFB002E8C40DC6448C
-:100280000A01F9C3834E7A40F8C3FBB001E8024A81
-:10029000FAE8991EE40A84C075F0B04EE60AFBB095
-:1002A00001E8EE49FAE8851EE40A84C075F0C3FA55
-:1002B000E87A1EE4EC884416E4E4884417E4F888FD
-:1002C0004418E4F0884419E41088441AE41288447D
-:1002D0001BE41488441CE43488441DE43688441E1E
-:1002E000E4D824018AE0E4DA24020AC488441F8A9C
-:1002F0004410E8CD1F8A4411E835218A4412E88968
-:10030000218A4413E84321C686A10000E414241086
-:10031000E614E412243DE6128A44153C01721E776D
-:1003200016B011E634B013E636E4140C10E614E40B
-:10033000120C40E612EB06E4120C02E6128A440F9D
-:100340003C0174063C02740AEB0EE4120C08E6123F
-:10035000EB06E4120C10E612E82FFF8A44143C026C
-:100360007508B05588440C88440DB021B4648944A4
-:1003700004894402E40C0C10E60CE8ED39FBC3E8F8
-:100380005F3F7308FBB00AE80849EBF3FAE89D1DEC
-:100390008A64168A441789869400E6E48AC4E6ECE7
-:1003A0008A64188A441989869600E6F08AC4E6F8B9
-:1003B0008A441AE6108A441BE6128A441CE6148A10
-:1003C000441DE6348A441EE6368A441FE6D8E6DA3F
-:1003D000E9B7FE90FA8A440EE6FEE402A80175052C
-:1003E00033C0FBF8C333C0E400FBF9C38A64148054
-:1003F000FC02742BFEC0FEC780FF4E721C74098085
-:10040000FF507308B00AEB17B00DEB1302DC32FF9C
-:1004100080FB7F7C02B3218AC33C7F7C02B021C376
-:10042000FA807C0B047602FBC38B46243D080072E5
-:10043000F68E46028B7E228A440C8B5C02AAE8ABC5
-:10044000FFAAE8A7FFAAE8A3FFAAE89FFF88440C39
-:10045000895C0280440B04897E22836E24048346D7
-:100460001A04807E26027406806626FDFBC360B0F7
-:10047000FDE8023F61FBC3FA807C0F037509C644A7
-:100480000B00E8E538FBC3C47E148B4E3A85C97572
-:1004900035268B0D4747E3EA3B7E047622B80200FF
-:1004A00039462E7707C7462E0000EB138B5E2C894A
-:1004B0005E0426C70700004343895E2C29462E852B
-:1004C000C978CE894E3A8A440D8B5C04268A25472A
-:1004D0003AC47516FE4C0BFF4406E80FFFE2ED88A8
-:1004E000440D895C04894E3AEBA7C6440AFEE879BC
-:1004F00038FBC390E8B30D8AE88A0ECB13B3078AA2
-:10050000C1EEEB00EC3AC1750902CDFECB75F0EB04
-:100510000C90880ECB138AE8BBFFFFF9C3880ECB83
-:1005200013F8C390BB3F3F8A8E9E00BAFE00EC8A50
-:10053000E832C122C37502F8C3F9C390E8E5FF733E
-:1005400001C3BAD000BB03038A8E9F00EC8AE83255
-:10055000C122C37502F8C3F9C39033C08ED88EC0D0
-:10056000803EC813007507B00AE82647EBF2FB335C
-:10057000DB8A1EC913434383FB7E760733DBB0025D
-:10058000E80F472E8BAF4400837E080074E7881E77
-:10059000C913B002E8FB46FAF7463840007414E885
-:1005A000961BE87FFF721C33D28A969F0083C20E8F
-:1005B000EB0C90E8771BE883FF7208BA4800E83339
-:1005C000FF73AB23CB898E9A0089969C00FE86B57B
-:1005D00000C606C81300B00AE8670AFBEB891018CA
-:1005E000082833C0A005018AC824407524C7067CAA
-:1005F000128E45C70642120100C606541202B00808
-:10060000F6C1017402B004A34612A24C12A29412C5
-:10061000C3C7067C12B645A00F0184C0750E6A00E0
-:100620001FC60693121E9C0EE8B10C90C70644121A
-:100630000100A342128BD8C1E304881E9412BEE2CB
-:10064000052BF08BC833DB8BFB2EAC888548128AD8
-:10065000D80C05E6FE8AE0EB00E4FE32C4A83F7445
-:1006600003E99E00E400888550128AE02430BA1025
-:10067000FF3C30741280FC04740ABA0403F60608C6
-:1006800001FE7403BA080F88954C1202FA32C0F6C4
-:10069000C4087402B001888558128AC43C35745B62
-:1006A0003C3674573C3474533C04744F3C14744BC4
-:1006B0003C157447A8407425C685541204D1E7B48C
-:1006C000038AC389855C128AC38AE380CC01898549
-:1006D0006412D1EF47E203EB1A90E96CFFC6855430
-:1006E0001202D1E78AE68AC30C0489855C12D1EF35
-:1006F00047E2E733C08AC7A34612C3C68554120631
-:10070000EBBBC68554120033C08885501288854CD7
-:100710001288855812EBA6C7462602128B461E8900
-:1007200046008946228B4620894624C7461A000087
-:10073000C3C7463C8000C7463801001E568B763042
-:100740008976048976148E5E0633C089044646890C
-:10075000762C89463A8B4632484889462E5E1FC31E
-:1007600033C089464889464AC74646AE0189464E47
-:100770008B46448946508B4642894640894608C389
-:1007800033C0894676894678C7467A1000561E8B54
-:10079000767089761089760C8E5E12C70400008B05
-:1007A00046728946741F5EC3895618895602895657
-:1007B0000689560A89560E8956128956168BD84BC9
-:1007C0004BC1E302BF0200897E1E03FB897E30031A
-:1007D000FB897E4203FB897E7083EB08895E20895A
-:1007E0005E32895E44895E7250E82BFFE871FFE853
-:1007F0003FFFE88BFF58C3B83075C1E8040E5B03B8
-:10080000C3A3BA13833E4212007407803E941200C1
-:10081000750E6A001FC60693121E9C0EE8BD0A9054
-:10082000B8307AC1E80440A3C0132B061201F7D8F0
-:1008300033D28BCA8A0E9412F7F13D8000770E6A8C
-:10084000001FC6069312259C0EE8900A90483DFFB3
-:10085000077203B8FF07A3C21333C98A0E94123379
-:10086000F6B800092E8BAC440089464C404646E25F
-:10087000F38A0E941233F68B16C013A1C2132E8B7B
-:10088000AC4400E822FF03D04646E2F2C333C02E58
-:100890008BAD44008946084747E2F4C35133C00A90
-:1008A000C22E8BAD440089869E00814E38002047C1
-:1008B00047FEC480FC04720432E4FEC0E2E35983C4
-:1008C000E9107405F7D9E8C4FFC35133C00AC22E3A
-:1008D0008BAD440089869E00834E3840474780C4D4
-:1008E00010790432E4FEC0E2E65983E9107405F79A
-:1008F000D9E899FFC3E8D2FFC38D089C08CA08F560
-:10090000088B0E421233F6515633DB8BCB8A944858
-:10091000128A8C4C128A9C54128BFEC1E70585DB2F
-:100920007502B1102EFF97F9085E5946E2D9C3014E
-:10093000CC03D000E802D000E801D000E800D000ED
-:10094000E804D0A8DA00DC00DE01D803CC03CC0335
-:10095000CC04D0A8DA20DC00DE03CC03CC03CC002E
-:10096000D803CC03CC03CC03CC03CC03CC03CC0303
-:10097000CC03CC03CC03CC03CC03CC03CC03CC03FF
-:10098000CC04D000DA20DC03DE01D803CC03CC0396
-:10099000CC03CC00D800CC00D0000056521E0E1F55
-:1009A000BE2F0933D2FCAD85C0740D8AD4EEAD855F
-:1009B000C074058AD4EEEBEE1F5A5EC3E48084C097
-:1009C00074167814B027E6FCB011E634E4FC3C273A
-:1009D0007506E4117502F8C3F9C383C206B0BFEE11
-:1009E00083EA02B010EE8886AF00B01183C204EE35
-:1009F00083C202EEB01383C202EE83C202EE2EA1C6
-:100A00004C2D8986940083EA0EEE83C2028AC4EEDE
-:100A100083C204B003EE8886A80083EA0432C0EEE5
-:100A200083C202B089EE8886A6000C06EEB040B400
-:100A30003889461CC74636380083C20432C0EE8867
-:100A400086A700C383C206B0BFEE83EA02EC3A86F3
-:100A5000AF00752483C204EC3C11751C83C206EC04
-:100A60003C13751483EA088A86A800EE83EA02EC38
-:100A700024C03CC07502F8C3F9C333C98BD18BF1D4
-:100A80008A0E9412C1E9022E8BAC4400F74638005E
-:100A900020740E8A869E00E6FE32C0E68042E8FAA6
-:100AA000FE83C608E2E185D27403E80508C333C9B2
-:100AB0008BF18A0E94122E8BAC4400F7463840001E
-:100AC0007406E87316E812FF4646E2EAC333C98BA0
-:100AD000F18A0E9412C1E9022E8BAC4400F746381D
-:100AE00000207416E84616E8D2FE730E6A001FC690
-:100AF0000693121C9C0EE8E3079083C608E2D9C354
-:100B000033C98BF18A0E94122E8BAC4400F7463811
-:100B100040007416E82116E82AFF730E6A001FC60B
-:100B20000693121C9C0EE8B307904646E2DAC30C0B
-:100B300000001000131200001400283C001B3E00AF
-:100B4000002A00002C0000420014D80000DA000047
-:100B50003400113600133800113A001300005650CB
-:100B600052BE2F0B2EAD85C07406922EACEEEBF468
-:100B70005A585EC3532EA16022E6E4E6F08AC4E62A
-:100B8000ECE6F8E8D8FFB04BE610B050E612B0380B
-:100B9000E614E8AE15B046E60AE8A715B01AE60A6C
-:100BA000E8A015B022E60AE89915E8FD068BD8E41E
-:100BB00016A8047518E8F2062BC33D320072F06ADD
-:100BC000001FC6069312239C0EE8100790E8DA0671
-:100BD0002BC33D2400771BB031E6FC565155B910AC
-:100BE000002E8BAC4400814E3880004646E2F25D18
-:100BF000595EE869FFE84B15B046E60AE844155B24
-:100C0000C333F68B0E42122E8BAC4400F7463800ED
-:100C1000207406E81715E85BFF83C620E2E9C38B62
-:100C2000C20504008946282EA14C2D89868E008994
-:100C300086900089869200C686A3000AC686C300F5
-:100C4000035283C2048A86A6000C06EE5A83C202AF
-:100C5000B005EE8886A500C3E803FFE8E514B042BE
-:100C6000E60AF74638800074062EA19C22EB042E7B
-:100C7000A16C22C7461C0C008986940089869600C8
-:100C800089868E008986900089869200E6F0E6E4E7
-:100C90008AC4E6F8E6ECC686C30003E8A514B01AD9
-:100CA000E60AB0108886A500E60CC333C98BF18A2A
-:100CB0000E94122E8BAC4400F7463840007406E8C0
-:100CC0007614E85AFF4646E2EAC333C98BF18A0E2E
-:100CD00094122E8BAC4400F7463800207406E84C82
-:100CE00014E874FF4646E2EAC390833E441200755E
-:100CF00014B001BA0601EE2AC0EEB002EEB004EE66
-:100D0000B80002EB0FBA0601B040EEB801008A0E3F
-:100D10000E01D3E0A38812C3A18812A384122D2050
-:100D200000A38A122D2000A38212C706861220007B
-:100D3000C70680123200C3833E44120074768B0EC5
-:100D4000421233F68AA4541284E4745F8A844812EF
-:100D50000C04E6FEF6C4047425B01BBA0000EEEBEA
-:100D6000002AC0BA0200EEEB00B003EEEB0032C086
-:100D7000BA0200EEEB00BA0000B000EEEB2DB01F9F
-:100D8000BA0000EEEB002AC0BA0200EEEB00B0039E
-:100D9000EEEB00D1E68A845D12D1EEF6D0BA020005
-:100DA000EEEB00BA0000B00AEEEB00E404EB00E466
-:100DB0000446E290C390B81400BA3EFFEFB80600B4
-:100DC000BA32FFEFB80F00BA34FFEFBA36FFEF8345
-:100DD0003E4412007516B81100BA38FFEFB8120081
-:100DE000BA3AFFEFB81B00BA3CFFEFC3B81100BA24
-:100DF00038FFEFB81200BA3AFFEFB81B00BA3CFF59
-:100E0000EFC3B8FC00BA28FFEFFB833E4412007426
-:100E100007B8CC00BA28FFEFC300FFFF202428FF4B
-:100E20002CFFFF303438FFFF3C903C0F770EBB198E
-:100E30000E2ED73CFF74058AD8F8C3902ADBF9C37D
-:100E4000833E4412007427A00601802606013080EC
-:100E50003E0601307518B90200BFC413BA0601EC92
-:100E6000A82075F8BA0401EDABE2F1EB1690B904D5
-:100E700000BFC413BA0601ECA82075F8BA0401EC4F
-:100E8000AAE2F1FA90BEC413AD80E43F80FC027484
-:100E90000E6A001FC60693120A9C0EE83E0490AD2F
-:100EA0003C0F75ED8AC4E881FF72E6881E1A01C600
-:100EB000068E1200B0000A061A01BA0001EEC6063C
-:100EC0008F1240833E4412007506B80C00EB04906C
-:100ED000B84C00BA28FFEFC3833E4412007501C32B
-:100EE000A150120B0652120AC4A80874F2A00F01F6
-:100EF0002AE450FF36BA131FE8505683C4026A0032
-:100F00001F33C0A3BC13A00F01A3BE138B1EBC13C1
-:100F10008A875012F687501208740D24078AE0BEA3
-:100F2000CC00A0BC13E8943DFF06BC13FF0EBE131B
-:100F300075DAC3901E33C08ED8B001E8543D1FC38C
-:100F400033C98BF18A0E94122E8BAC4400C74662D3
-:100F50003844C7467CFC3BC7467EE23BC7868000E0
-:100F6000EC3CE8AB16C686C00011837E080074070F
-:100F70005156E833335E594646E2CDC333C98BF14F
-:100F80008BF98A0E9412C1E902E3132E8BAC440054
-:100F90008A869E0088856C1283C60847E2EDC3FAF4
-:100FA000FCB0C0BA0001EE33C08ED88EC08ED0BF68
-:100FB0001601B9CC772BCFD1E9F3ABBC4012E8D9FD
-:100FC00002E8703CBECC0FE8F23CF49033C08ED8FF
-:100FD0008EC08ED0F6060A0180740BBE3555E8DB54
-:100FE0003CB001E8AC3CE8B300E8F6F5E808F8E806
-:100FF0000FF9E885FAE8B6FAE8EFFCE8C210E80372
-:101000003CE8B2FDE830FDE85402C6068F12C0E8A5
-:10101000BBFAE8EBFAE8E9FBE8AFFCE88DFCE81F77
-:10102000FFE858FFE8DBFDE816FE33C0BE5A05E8CE
-:101030008A3CE8A3FEE8E0FCFBBEA444E87D3CE972
-:10104000CA2D56988BF08B425285C07527C74252E5
-:10105000010053368B9C2C01F6C301750C36896850
-:10106000523689AC2C015B5EC33689AC2C013689C3
-:10107000AC1C015B5EC356988BF033ED368B841C41
-:1010800001A80175158BE833C08742523689841C4C
-:1010900001A80174053689842C015EC3565133F6CC
-:1010A000B80100B9080089841C0189842C014646D6
-:1010B000E2F4595EC390BB01008BE8FF4E6E740AE8
-:1010C0008BDD8B4658A80174F0C38B4648A90800F5
-:1010D0007445F7463840007427E85C1080C2068AE1
-:1010E00086A80024BF8886A800EE60B0FEE886329D
-:1010F00061B002E84CFF8B464824F7894648EB175D
-:10110000E82A10814E2600408A86A5000C028886B7
-:10111000A500E60C8B4648A904007414B002E8212F
-:10112000FF8B464824FB89464860B0DFE8473261C0
-:1011300033C0874658F6C301750B36894758A80156
-:10114000750DE974FFA32201A8017503E96AFF89FF
-:101150001E3201C3BB01008BE8F74638400074150E
-:10116000E8D50F80C20AECA840750A8BDD8B465685
-:10117000A80174E3C38B462680E4FE80CC02894636
-:1011800026B002E8BCFE33C0874656F6C301750A96
-:1011900036894756A801750BEBBDA32001A8017540
-:1011A00002EBB4891E3001C3601E062BC08ED8A08E
-:1011B000901284C07549A12201A8017503E8F6FECA
-:1011C000A12001A8017503E88AFFA1AC13487805A6
-:1011D0007445A3AC13A1AE134878057451A3AE13A4
-:1011E000A1B0134878057463A3B013A17E124078B0
-:1011F00003A37E12B80080BA22FFEF071F61CFA0C1
-:101200009112403C02720B33C0A29112FF167C1265
-:10121000EBA4A29112EB9FA08E1232068F12A28E27
-:10122000120A061A01BA0001EEB82C01EBA4833EA3
-:101230008412107211BA28FFED0C81EFE85337BA0F
-:1012400028FFED247EEFB80400EB92C6068D120154
-:10125000E83F37C6068D1200A1B213EB8B908A1EB1
-:101260000B012AFF6BC319BA62FFEFB80A00BA601C
-:10127000FFEFB801E0BA66FFEFB8FFFFBA52FFEF29
-:10128000B809C0BA56FFEFC706AC132C01C706AEAB
-:10129000130400C606911200C3908A1E0B012AFF98
-:1012A0006BC305D1E8A31801C39052BA50FFED5AA1
-:1012B000C39053518B1E1801B9320590E2FE4B7555
-:1012C000F7595BC3B080BA00010A061A01EEC39059
-:1012D000B040EBF2B0C0EBEEB000EBEAFA60061EF5
-:1012E000162BDB8EDB2EA1BA4C2EA3924CA09312B0
-:1012F000988BE889262D7A803ECA13007403E96B27
-:1013000042E8C0FFE8ABFFE8A8FFB020C606901295
-:1013100000FF167C128BFD83FF0A7211E8B9FFE80B
-:1013200090FFE8ABFFE88AFF83EF0AEBEA0BFF745C
-:101330000FE8A4FFE87BFFE89AFFE875FF4F75F11F
-:10134000E895FFE86CFFEBB98A86A50024FDEE88DE
-:1013500086A500C38A86A6000C02EEC38B7638F7FA
-:10136000C6010074EF8B4E368B462E3BC173028B49
-:10137000C82BC189462E014E34C47E0426010D8B34
-:101380007E2C83EA04F36C8EC1897E2C3B463C7232
-:1013900012F7C62000750B83CE20897638B000E89E
-:1013A000A0FCC3F7C60400741B8BD883CE108976CB
-:1013B000388A86A70024FE8886A70083C208EE83A9
-:1013C000EA088BC33D40007201C3814E380004839C
-:1013D000C2028A86A50024FA8886A500EEC38A8602
-:1013E000A6000C02EEC3F74638010074F18B4E2EB6
-:1013F00032DB8ABEA30083C206C476048B7E2C83B4
-:10140000F908722CECA80174168AE083EA0AEC83CE
-:10141000C20A84E77551AAFEC34983F90873E5320D
-:10142000FF26011C015E34897604894E2E897E2CAC
-:101430003B4E3C7211F64638207401C3834E38206F
-:10144000B000E8FDFBC3F64638047415834E38102F
-:101450008A86A70024FE8886A70083EA02EE83C25C
-:10146000023D4000725DC332FF26031C85DB740918
-:1014700026891C8BF74747494980E41E80CCC0264B
-:101480008904F6C41074278B7638F7C60010740BE5
-:1014900050FE86B200B00AE8A8FB58F7C6000174F7
-:1014A0000DE882268B76388B4E2E8B7E04AB8BF725
-:1014B00033C0AB32DB8ABEA300494983F9087217F7
-:1014C000E941FF814E38000483C2F88A86A50024D2
-:1014D000FA8886A500EEC3E945FF83C208EC88863A
-:1014E000AA00C0E8048AE08AC88686A90032E08B98
-:1014F0005E3E84E3744F8AC18B4E26F6C504740C9D
-:10150000A808740580E1BFEB0380C940F6C50874E4
-:101510000CA802740580E17FEB0380C980884E2609
-:101520008BF08A86A50084C97408A802741524FD6E
-:10153000EB06A802750D0C028886A50083EA0AEE68
-:1015400083C20A8BC684E77501C3C686BA0001B0A0
-:101550000EE8EEFAF74638000274EE837E2E06722D
-:10156000E88AA6AA00C45E048B7E2CB0FFAAB00253
-:10157000AB26830703836E2E03897E2CF646382024
-:101580007401C3834E3820B000E8B6FAC39083EAF2
-:1015900008E9B4FD83C2068B5E26F6C3C075EF8BE7
-:1015A0004E1CEC8886A40083EA0AA82075028ACD26
-:1015B00032ED8B461A3BC87318014E2A2BC189465F
-:1015C0001AC57600F36E8ED98976003D2000723000
-:1015D000C385C074318BC801462AC57600F36E8E70
-:1015E000D980CB02895E26E832F1F6C701751683F1
-:1015F000C202E853FDF6C710750BB002E843FAC308
-:10160000F6C70174F0C380CB02895E26F6C7017469
-:10161000DE83C202E831FDF686A40040740B80E749
-:10162000FE80CF02895E26EBCCB004E814FAC3C07A
-:10163000C2C8CAC4C6CCCED0D2D8DAD4D6DCDE90EA
-:10164000E90E01E4C48AE0E4C48BD083F90872F0A7
-:1016500026833F0074048BDF49498BFB8ADE83E3DA
-:101660000F2E8AA72F16ABF6C4107424F7C60010ED
-:10167000740B50FE86B200B00AE8C6F958F7C600EF
-:1016800001740DE8A0248B76388B4E2E8B7E04AB34
-:10169000897E0433C0AB4949894E2E897E2C8BC18B
-:1016A000EB4E90EB9E90E4D684C07963E6D08AC876
-:1016B00025030003D8D1E32E8BAF4400888EAE0003
-:1016C0008B4E2EC45E048B7E2C8B7638E4862407EA
-:1016D0003C0375CFE41C913BC173028BC82BC189BD
-:1016E000462E014E3426010FBAC400F36C897E2CBD
-:1016F0003B463C721CF7C62000750B83CE208976D2
-:1017000038B000E83CF98A86AE00243FE6D6C3F93B
-:10171000C3F7C60A007435F7C61000752F83CE10C4
-:10172000897638F7C60200740E50E4D824FEE6D855
-:1017300058F7C6080074155051B9E803E40A84C08C
-:10174000E0FA84C07504B024E60A59583D4000739D
-:10175000B58A86A50024EF8886A500E60C81CE1008
-:1017600004897638EBA00008040C0109050D020A73
-:10177000060E030B070F004080C02060A0E0105051
-:1017800090D03070B0F0E4D2E6D08AC825030003D0
-:10179000D8D1E32E8BAF4400888EAE00E4D8C0E8E9
-:1017A000048BD82E8A8766178AE08AC88686A900A5
-:1017B00032E0E4988B5E3E84E374548AC18B4E26FB
-:1017C000F6C504740CA808740580E1BFEB0380C95A
-:1017D00040F6C508740CA802740580E17FEB038015
-:1017E000C980884E268BF08A86A500F6C1FD740854
-:1017F000A806741924F9EB0FA8067511F6C5017532
-:10180000040C04EB020C028886A500E60C8BC6844F
-:10181000E775098A86AE00243FE6D2C3C686BA00C1
-:1018200001B00EE81CF8F74638000274E6837E2EFD
-:101830000672E08A86A9008AE08686AA008AC832F3
-:10184000C480C90B22C1C0E4040AE0C45E048B7EDC
-:101850002CB0FFAAB002AB26830703836E2E038948
-:101860007E2CF646382075AB834E3820B000E8D188
-:10187000F7EBA090E41224DFE61281E3FE9F895E7D
-:1018800026836648F7EB7390F6C72075E7E4120CE1
-:1018900020E61232C0E6C6B083E6C680CF20895E5D
-:1018A000268A86A5000C028886A500E60CEB7490BB
-:1018B000F6C74075D3E4120C20E61232C0E6C6B07B
-:1018C00081E6C680E7DF80CB01895E26B006E8713D
-:1018D000F7908A86A50024F9E60C8886A500EB43DC
-:1018E000E4D4E6D08BF825030003D8D1E32E8BAFE8
-:1018F00044008B5E26F6C76075B6F6C3C075D3BAD2
-:10190000C6008B4E1C8B461A3BC8731E014E2A2BF9
-:10191000C189461AC57600F36E8ED98976003D20BE
-:1019200000723D8BC7243FE6D4C385C074398BC891
-:1019300001462AC57600F36E8ED983CB02895E26D6
-:10194000E8D9EDF6C70175398A86A50024F9E60CB9
-:101950008886A500F6C71075CAB002E8E4F6EBC3A6
-:10196000F6C70174EFEBBCF6C70174DC8A86A500EC
-:10197000A802741181E3FFFE81CB0002895E26EB91
-:10198000C78A86A50024FB0C02E60C8886A500EB1E
-:101990009290FDF7DF7FFEFBEFBF0004000405041B
-:1019A00005040104000405040504060406040504F6
-:1019B00005040604060405040504020400040504E5
-:1019C00005040104000405040504060406040504D6
-:1019D00005040604060405040504070407040504B9
-:1019E00005040704070405040504060406040504A9
-:1019F0000504060406040504050407040704050499
-:101A00000504070407040504050406040604050488
-:101A10000504060406040504050403040004050483
-:101A20000504010400040504050406040604050475
-:101A30000504060406040504050402040004050464
-:101A40000504010400040504050406040604050455
-:101A50000504060406040504050407040704050438
-:101A60000504070407040504050406040604050428
-:101A70000504060406040504050407040704050418
-:101A80000504070407040504050406040604050408
-:101A90000504060406040504050433DB8AD88A8796
-:101AA0006C12E6FEC1E302E4CEA8047509A8027434
-:101AB00003E92CFEF9C35053E8CBFC5B58A8027431
-:101AC00003E91CFEF8C333DB8AD88A876C12E6FE72
-:101AD000C1E302E9D0FB9A1AC61A00000200040012
-:101AE00002000600020004000200080002000400D8
-:101AF000020006000200040002000A0002000400C6
-:101B000002000600020004000200080002000400B7
-:101B1000020006000200040002000C0002000400A3
-:101B20000200060002000400020008000200040097
-:101B3000020006000200040002000A000200040085
-:101B40000200060002000400020008000200040077
-:101B5000020006000200040002000E000200040061
-:101B60000200060002000400020008000200040057
-:101B7000020006000200040002000A000200040045
-:101B80000200060002000400020008000200040037
-:101B9000020006000200040002000C000200040023
-:101BA0000200060002000400020008000200040017
-:101BB000020006000200040002000A000200040005
-:101BC00002000600020004000200080002000400F7
-:101BD00002000600020004000200C390DA1494150B
-:101BE0005C13E613DA1BDA1BE613DA1B8B94641220
-:101BF000C1E604A80174355033C08AC2E6FEE4A0F1
-:101C000085C074278BD82E8A9FDA1A52562E8BA83D
-:101C100044008B5628ECA801750D8886AD00240E73
-:101C20008AD82EFF97DC1B5E5AEBCD58A80274367B
-:101C300083C61033C08AC6E6FEE4A085C074278B35
-:101C4000D82E8A9FDA1A52562E8BA844008B56281B
-:101C5000ECA801750D8886AD00240E8AD82EFF975A
-:101C6000DC1B5E5AEBCDC39032E48BD88BD02E8A2E
-:101C70009F9A192E2297921956528AC3240303C69B
-:101C800080E304D0EB2EFF97D61A585EA955007555
-:101C9000D9C3601E062BC08ED8A15C12E6FEE400FC
-:101CA00022C4740833F6E8BFFFEBEE90E40407E4C7
-:101CB000041FB80080BA22FFEF61CF90601E062B90
-:101CC000C08ED8A15E12E6FEE40022C47408BE04F1
-:101CD00000E894FFEBEDE40407E4041FB80080BAC9
-:101CE00022FFEF61CF90601E062BC08ED8A15C1240
-:101CF000E6FEE40022C4741833F6E86BFFA160121C
-:101D0000E6FEE40022C474E5BE0800E85AFFEBDDFD
-:101D1000A16012E6FEE40022C475EDE40407E404C9
-:101D2000A15C12E6FEE4041FE404B80080BA22FFBE
-:101D3000EF61CF90601E062BC08ED8A15E12E6FE2A
-:101D4000E40022C47419BE0400E81CFFA16212E67C
-:101D5000FEE40022C474E4BE0C00E80BFFEBDCA13F
-:101D60006212E6FEE40022C475EDE40407E404A177
-:101D70005E12E6FEE4041FE404B80080BA22FFEF1E
-:101D800061CF601E062BC08ED8A15C12E6FEE480F7
-:101D900084C4740833F6E853FEEBEE90B80080BAC2
-:101DA00022FFEF071F61CF90601E062BC08ED8A1C7
-:101DB0005E12E6FEE48084C47408BE0200E82CFED5
-:101DC000EBEDB80080BA22FFEF071F61CF90601ED5
-:101DD000062BC08ED8A16012E6FEE48084C474088D
-:101DE000BE0400E806FEEBEDB80080BA22FFEF0764
-:101DF0001F61CF90601E062BC08ED8A16212E6FE36
-:101E0000E48084C47408BE0600E8E0FDEBEDB80091
-:101E100080BA22FFEF071F61CF90601E062BC08E95
-:101E2000D8A15C12E6FEE40022C4741833F6E83749
-:101E3000FEA16012E6FEE48084C474E5BE0400E8FE
-:101E4000AAFDEBDDA16012E6FEE48084C475EDA17D
-:101E50005C12E6FEE40407E4041FB80080BA22FF27
-:101E6000EF61CF90601E062BC08ED8A15E12E6FEF9
-:101E7000E40022C47419BE0400E8ECFDA16212E67D
-:101E8000FEE48084C474E4BE0600E85FFDEBDCA1E0
-:101E90006212E6FEE48084C475EDA15E12E6FEE403
-:101EA0000407E4041FB80080BA22FFEF61CF601E70
-:101EB000062BC08ED8A15C12E6FEE48084C47418A0
-:101EC00033F6E827FDA16012E6FEE40022C474E5C3
-:101ED000BE0800E892FDEBDDA16012E6FEE4002200
-:101EE000C475EDE40407E4041FB80080BA22FFEFD4
-:101EF00061CF601E062BC08ED8A15E12E6FEE48084
-:101F000084C47419BE0200E8E2FCA16212E6FEE499
-:101F10000022C474E4BE0C00E84DFDEBDCA16212AB
-:101F2000E6FEE40022C475EDE40407E4041FB800F3
-:101F300080BA22FFEF61CF90601E062BC08ED8A121
-:101F40005C12E6FEE48084C4741833F6E89DFCA1BC
-:101F50006012E6FEE48084C474E5BE0400E88CFCF4
-:101F6000EBDDA16012E6FEE48084C475ED071FB8C6
-:101F70000080BA22FFEF61CF601E062BC08ED8A171
-:101F80005E12E6FEE48084C47419BE0200E85CFCC4
-:101F9000A16212E6FEE48084C474E4BE0600E84B4D
-:101FA000FCEBDCA16212E6FEE48084C475ED071F41
-:101FB000B80080BA22FFEF61CF90601E062BC08E62
-:101FC000D8902AC0E6FEE4CEA801741433DBE8D52D
-:101FD000F6EBEF90B80080BA22FFEF071F61CF90B9
-:101FE000F60605010175EDB001E6FEE4CEA8017428
-:101FF000E3BB0400E8AFF6EBC990601E062BC08E71
-:10200000D890FB90FA2AC0E6FEE4CEA802741333FF
-:10201000DBE8CCF8EBECB80080BA22FFEF071F61D9
-:10202000CF90A80474F033DBE85BF7EBD590601E2B
-:10203000062BC08ED890FB90FAB001E6FEE4CEA845
-:10204000027415BB0400E897F8EBEB90B80080BA77
-:1020500022FFEF071F61CF90A80474F0BB0400E8D3
-:1020600024F7EBD26A001FC6069312099C0EE86B98
-:10207000F2906A001FC6069312299C0EE85DF2904A
-:10208000722072207220CE1D921CE61C1A1E722035
-:10209000821DAE1E381F7220821D72207220381FD2
-:1020A000722072207220F41DBC1C341D641E72202C
-:1020B000A81DF21E781F7220A81D72207220781FA2
-:1020C000FCB940008CCBB864202BFFAB93AB93E200
-:1020D000FAC7064C00A811833E4412007520C706BB
-:1020E0003C00084BC7063000BA1FC7063400FA1F71
-:1020F000F6060501017506C70638002E20C3C7067F
-:102100003C00564B33DB8A1E5412C1E302021E56BA
-:10211000122E8B878020A330008A1E5512C1E30245
-:10212000021E57122E8B87A020A33400C38B869EDD
-:1021300000E6FE86C4E6D0C38B869E00E6FE33D260
-:102140008AD4C351B91027E40A909084C07405E280
-:10215000F659F9C359F8C384C0781E518AE88AC871
-:10216000B80100D3E0098698003AAEA00059751076
-:10217000E8A9E5834E2602F9C39889869800EBF01A
-:10218000F8C384C07812518AE08AC8B80100D3E04D
-:1021900059F7D021869800C3C78698000000C383F2
-:1021A000C2048A86A6000C04EE83EA04C3E893FF07
-:1021B0007204B082E60AC38B4626A8FD74118A8693
-:1021C000A500A806740824F98886A500E60CC3F6C5
-:1021D000C401740A8A86A50024FB0C02EB0CA80239
-:1021E000750F8A86A50024FD0C043A86A50075D8D3
-:1021F000C38A86A500EBCFE4D833DB8AD8C0EB04D2
-:102200002E8A9F6617889EA9008B5E2680E33FF684
-:10221000C7047407A810750380CB40F6C70874077D
-:10222000A880750380CB40885E268A86A500F6C309
-:10223000FD740DA806740824F98886A500E60CC371
-:10224000F6C70174040C02EBF0F6C30275E90C0446
-:10225000EBE7C404C4048504590448044104C303DF
-:10226000820341038202570241028201410182003E
-:1022700041004E02AD0157012D002B002700210027
-:102280001600F404F404A3046F045B045104F40383
-:10229000A3035103A3026D025102A3015101A30044
-:1022A00051006202D9016D01380036003100290069
-:1022B0001B005157BF0200EB0F905156BF0100EBBE
-:1022C00007905156BF0300903C197602B017988BC7
-:1022D000F08A82C4002AE48BF083FE187346D1E6AC
-:1022E0002E8B8C5222F74638800074052E8B8C8200
-:1022F00022F7C7020074123B8E9400740C898E94EE
-:10230000008AC5E6EC8AC1E6E4F7C7010074123B17
-:102310008E9600740C898E96008AC5E6F88AC1E60E
-:10232000F05E59C377068B8E8E00EBC58B8E9000C6
-:10233000EBBFD503F6003E0010000400CA043301D1
-:102340004D00140005000103050709000102030404
-:1023500080841E00A02526000000608BF033FF2E35
-:10236000A150232E8B165223BB3223F74638800010
-:10237000740C2EA154232E8B165623BB3C23B90577
-:10238000002E3B31730A4747E2F7B8FFFFEB1D9081
-:10239000D1EF2E8A8D46232AEDD1EAD1D8E2FAF781
-:1023A000F6050200C1E8022E8AA54B232EA358236E
-:1023B000612EA15823C3080020008000000260099C
-:1023C0000800200080000002000800000100020058
-:1023D0000300040052565785C074053D0109760379
-:1023E000B80109BF5B01F7463880007403BFB20132
-:1023F00033F62E3B84B62376044646EBF5F7E72EFC
-:102400008BBCC02303C783D200D1E7F7F72E8AA481
-:10241000CA235F5E5AC3E43E80BEC30003750CF757
-:10242000467A200074050C80E63EC3247FE63EC356
-:1024300024038886C3008AE0E41024FC0AC4E61062
-:10244000808EA10042E8CEFFC390568BF083E60752
-:10245000D1E62EFFA458249068246C2470247424A0
-:102460007824872487248724B400EB0EB4C0EB0AB9
-:10247000B440EB06B420EB02B4A0E410241F0AC45D
-:10248000E610808EA100425EC3903C0277128AE083
-:10249000E41024F3C0E4020AC4E610808EA10042D6
-:1024A000C3908B5E3884C0741F3C02742083CB08B9
-:1024B0008B462E3B463C770CE888FC7207B024E63E
-:1024C0000A83CB10895E38C383E3F7EBF7F7C310B9
-:1024D0000074F5E86DFC72EC8A86C000E638B02323
-:1024E000E60AEBE08B5E388B462E3B463CE4D87721
-:1024F0000B24FE80CB12E6D8895E38C30C0180CB5A
-:1025000002EBF35033DBC1E804250F0F8AD82E8A83
-:102510008766178ADC2E8AA7661709463E58C3507D
-:1025200033DBC1E804250F0F8AD82E8A8766178A05
-:10253000DC2E8AA76617F7D021463E58C38B463E4D
-:1025400033DB8AD80ADC2E8A877617E62C8AE0E409
-:102550002A240F0AC4E62A8A86A50084E4750DA8F9
-:10256000807411247F8886A500E60CC3A8807504BA
-:102570000C80EBF1C31E6033C933D233F68ED98D94
-:10258000BEFD00578B0584C074168BD1428BFE4F65
-:10259000780938A3E40074084F79F788A2E400466C
-:1025A0005F83C7094183F91072D989B6860089967D
-:1025B0008400611FC353C7466600008B4664A94070
-:1025C00000740DB300A980007402B37F889EC1001F
-:1025D00032DBA90200740380CB40A9004074038061
-:1025E000CB02A90080740380CB01A9301E74038044
-:1025F000CBBCA90020740380CB08A904017403801C
-:10260000CB10A90800740380CB20889EC2005BC356
-:102610000651575016078DBEC400B91F0033C0AA1B
-:1026200040E2FC8B86920089868E00898690005855
-:102630005F5907C3E4D8C0E80453250F008BD82E98
-:102640008A8766178886A9005AC30886AC00C686A2
-:10265000BA0001B00EE8EAE9C3AD36A3B413AD3653
-:10266000A3B613AD36A3B81383E90636F706B6133F
-:102670000F00C38A4626F74648800074020C108873
-:1026800086BD0032C0837E1A00750E8B5E4043808B
-:10269000E3FE3B5E0875020C01837E3A00750D1E59
-:1026A000C55E148B1F1F85DB75020C02F7463810C0
-:1026B0000074020C048B5E7AF7C3020074020C08EB
-:1026C000F7C3040074020C10F7C3080074020C2056
-:1026D000F7C3400074020C408886BF00C3906A00B4
-:1026E0001FC60693120D9C0EE8F1EB90B002E6DADD
-:1026F000F8C333C0E6DAF8C3B001E6D8F8C333C094
-:10270000E6D8F8C3B0FFE84EFAE8A1FAF8C3AC493E
-:10271000E8AFFBF8C390AC49E815FDF8C390AC49AD
-:10272000E867FDF8C390AC49E81FFDF8C390AC49D9
-:10273000E634F8C3AC49E636F8C3AC493C02771F2F
-:1027400084C0751DE41424EFE614E412243FE6125D
-:10275000E416A8047409E8EAF97204B018E60AF865
-:10276000C38AE0E4140C10E614E4120CC0F6C401B1
-:102770007402247FE612F8C3AC49E825FDF8C39043
-:10278000B80040E87DFDE8B4FDE8A8FEB001E8B976
-:10279000FEF8C390B80040E885FDE8A0FDF8C390BE
-:1027A000B80010E85DFDE894FDE888FEB008E899FF
-:1027B000FEF8C390B80010E865FDE880FDF8C3900E
-:1027C000B80080E83DFDE874FDE868FEB002E879F5
-:1027D000FEF8C390B80080E845FDE860FDF8C390BE
-:1027E000B80020E81DFDE854FDE848FEB004E859B3
-:1027F000FEF8C390B80020E825FDE840FDF8C3903E
-:10280000AC49E84814E43C24E70AC4E63CF8C39029
-:10281000B8FC3B89467CE43C0C18E63CF8C3E41267
-:102820000C02E612F8C3E41224FDEBF6E8B5FCF85E
-:10283000C390836638FDF8C3AC49A8017406834E83
-:102840007A20EB0483667ADFE8CBFBF8C3908A86B4
-:10285000A5000C0224FB8886A500E60C814E26010B
-:1028600020AC4932E489466E834E48084946F9C394
-:102870008A86A5000C0224FB8886A500E60C814E02
-:10288000260120ACB40AF6E4EBD8E8FA13E43C24C1
-:10289000F80AC4E63CF8C390AD4949894664A901E9
-:1028A00000741B8BD883E3FA751AA90400740FE433
-:1028B0003E0C02E63EB83844894662F8C390E43ED6
-:1028C00024FCEBEFE43E24FCE63EE8E8FCB8AA403A
-:1028D000EBE6E86EF87205B018E60AF8C390AC496A
-:1028E000E8CFF9F8C390AC49E8CFF9F8C390E868AD
-:1028F000FD750632C0E6DAF8C3B002E6DA36A0B4F7
-:102900001324103410E8160136A1B413A901007481
-:1029100005E8FCFEEB0EA90200740432C0EB02B025
-:1029200001E8DEFE36A1B413E8B513E43C24F80A4E
-:10293000C4E63C36A1B413C1E805250100E8FAFE5F
-:1029400036A0B5132410E859FB32C0368A26B513D9
-:10295000F6C4047409FEC0F6C4087402FEC0E8DBC5
-:10296000FD36A1B613250F00E857F936A1B613C1FD
-:10297000E804250300E8B8FA36A1B613C1E8052536
-:102980000200E805FB36A1B613F6C401750432C097
-:10299000EB0980E402D0ECB0022AC4E8ACFA36F6C7
-:1029A00006B713407405E883FEEB03E884FE36F6B1
-:1029B00006B713207405E865FEEB03E868FEF8C36C
-:1029C000E4120C01E612F8C3E41224FEEBF6E41460
-:1029D00024F00C05E614E42A24F00C06E62AF8C3D9
-:1029E000E42A24F0E62AE41424F00C07E614F8C3E1
-:1029F000AD4949E864F989868E00F8C3AD4949E8D4
-:102A000058F989869000F8C3834E2604E8A8F7F8A1
-:102A1000C390836626FBE89EF7F8C390AC4984C058
-:102A2000750DE41024EFE610808EA10042F8C3E497
-:102A3000100C10EBF190AC493C02760232C0C0E0C1
-:102A400004A82074020C0824188AE0E41224E70A7F
-:102A5000C4E612808EA10044F8C3AC498886C00049
-:102A6000F8C3AC49E63AF8C3AC4984C07408E41230
-:102A70000C04E612F8C3E41224FBEBF6AC49E8D6EA
-:102A8000F67303E827F7F8C3E412A802740424FDE0
-:102A9000E612B8F000E887FA816626FFF3E857F7F8
-:102AA000E89AFAF8C390B88000E857FA804E2708F1
-:102AB000E844F7E887FAF8C3B88000E861FA81666D
-:102AC00026FFF7E831F7E874FAF8C390B81000E889
-:102AD00031FA804E2704E81EF7E861FAF8C3B8100F
-:102AE00000E83BFA816626FFFBE80BF7E84EFAF8B0
-:102AF000C39033C0AC493C017304B001EB063C0CFD
-:102B00007602B00C89461CF8C390814E2600208ABC
-:102B100086A5000C0224FB8886A500E60C834E26C1
-:102B200001F8C390814E2600408A86A5000C0288D9
-:102B300086A500E60CF8C390AC4950E805F658723B
-:102B400008E638B023E60AF8C3F9C390AC50ADE804
-:102B500082F85AF6C201741239869600740C89867E
-:102B60009600E6F086E0E6F886E0F6C202741039D8
-:102B7000869400740A89869400E6E486E0E6EC8395
-:102B8000E903C390E4168886BC00E8E6FA33DBE488
-:102B90000CA806740380CB01A810740380CB02A894
-:102BA00080740380CB04E4128AE024180AD8E4DAA3
-:102BB000F6C4027407A840750380CB20A8027509EB
-:102BC000E42AA80F740380CB40F74638020074094A
-:102BD000E4D8A801750380CB80889EBE00FE86B431
-:102BE00000B00AE85CE4F8C3AC493C027441771FCA
-:102BF00050E84FF558720C84C0740AB012E60A808F
-:102C00004E3801F8C3B011E60A806638FEF8C38B6F
-:102C1000463825FFF7894638A9000475E68A86A557
-:102C200000A81075DE0C108886A500E60CF8C3819C
-:102C30004E3800088A86A500A81074C724EFEBE779
-:102C4000AD49493C0172113C0C770D508AE0E41407
-:102C500025F00F0AC4E614588AC484C07402E64200
-:102C6000F8C3E8CFF9FE86B900B00EE8D4E3F8C3A4
-:102C70003A86AF00741F8886AF008AE080C206B033
-:102C8000BFEE80EA028AC4EE8A86A80080C202EE05
-:102C900080EA068AC4C38B463E85C08A86A5007436
-:102CA00012A808750D0C088886A50080C202EE8067
-:102CB000EA02C3A80874FB24F7EBEC8B462684C019
-:102CC00074168A86A500A802740D24FD8886A500C6
-:102CD00083C202EE83EA02C38A86A500A80275F7C2
-:102CE0000C02EBE85283C20CECC0E8048886A90011
-:102CF0008B5E2680E33FF6C7047407A8087503803F
-:102D0000CB40F6C7087407A802750380CB80885EA5
-:102D1000268A86A50084DB7410A802740A24FD8824
-:102D200086A50083EA0AEE5AC3A80275FA0C02EBE4
-:102D3000EE90FFFF00480030BA20C41A00180012BD
-:102D4000000C0006000300028001C000600030009B
-:102D50001800CD0100018000100010000E000C00D2
-:102D6000080000000000060004000300020001004B
-:102D70005251563C1E7747988BF08A82C40032E449
-:102D800083FE18743D83FE19743E83FE1E772FD197
-:102D9000E62E8B8C322D3B8E94007422898E94000B
-:102DA00083C2068A86A8008AE00C80EE83EA068A3F
-:102DB000C1EE83C2028AC5EE83C2048AC4EE5E59A4
-:102DC0005AC38B8E8E00EBCE8B8E9000EBC8525187
-:102DD0003D05007703B805008BC8BA0200B800D0E3
-:102DE000F7F1050100D1E8595AC38B467AA820743F
-:102DF0000B80BEC3000375040C01EB0224FE894660
-:102E00007AC324038886C3008AA6A8008ADC80E4EB
-:102E1000FC0AC43AC3740B8886A80083C206EE83FA
-:102E2000EA06E8C5FFC30008183828903C04772359
-:102E300032E48BD82E8A87262E8AA6A8008ADC80C8
-:102E4000E4C70AC43AC3740B8886A80083C206EE9E
-:102E500083EA06C384C07402B0048AA6A8008ADC90
-:102E600080E4FB0AC43AC3740B8886A80083C206B8
-:102E7000EE83EA06C3908B5E3884C074343C0274DF
-:102E80003B8A86AF000C04E8E6FD8B462E3B463CB1
-:102E9000771BF7C30004751581CB000483C2028A37
-:102EA00086A50024FA8886A500EE83EA02895E38AA
-:102EB000C38A86AF0024FBE8B6FDEBF1F7C3100030
-:102EC00074EFEBED83C20CEC83EA0CC0E804888657
-:102ED000A900C3908A86A7000C018886A7008BDA18
-:102EE00080C208EE8BD3F8C38A86A70024FEEBEAE3
-:102EF0008A86A7000C02EBE28A86A70024FDEBDAA3
-:102F0000B0FFE852F2E897F2F8C3AC49E861FEF886
-:102F1000C390AC49E8EBFEF8C390AC49E835FFF844
-:102F2000C390AC49E805FFF8C3905283C206B0BF16
-:102F3000EE5283C202AC49EE5A8A86A800EE5AF8D5
-:102F4000C3905283C206B0BFEE5283C206EBE69036
-:102F5000AC493C02770D84C0750B8A86AF0024FD16
-:102F6000E80DFDF8C3508A86AF000C02E801FD5B56
-:102F700083C2088A86A700F6C301740C24DF888602
-:102F8000A700EE83EA08F8C30C20EBF2AC49E8E5B1
-:102F9000FEF8C390B80040E869F5E8F9FCE824FFC2
-:102FA000B001E8A5F6F8C390B80040E871F5E8E58F
-:102FB000FCF8C390B80010E849F5E8D9FCE804FF34
-:102FC000B008E885F6F8C390B80010E851F5E8C5F8
-:102FD000FCF8C390B80080E829F5E8B9FCE8E4FE05
-:102FE000B002E865F6F8C390B80080E831F5E8A5CE
-:102FF000FCF8C390B80020E809F5E899FCE8C4FEA5
-:10300000B004E845F6F8C390B80020E811F5E8856B
-:10301000FCF8C390AC49E8340CF8C390B8FC3B8989
-:10302000467CF8C38A86AF000C80E843FCF8C39066
-:103030008A86AF00247FEBF28A86AF000C40E82F2F
-:10304000FCF8C3908A86AF0024BFEBF2AC49A8011C
-:103050007407834E7A20EB059083667ADFE88AFD59
-:10306000F8C383C2068A86A8000C408886A800EEB2
-:1030700083EA06AC4932E489466E834E2601834ECC
-:103080004808B006E8BBDF4946F9C39083C2068A08
-:1030900086A8000C408886A800EE83EA06ACB40A35
-:1030A000F6E4EBD0E8E00BF8C390AD4949894664FB
-:1030B000A9010074198BD883E3FA750AA904007476
-:1030C0000DB8E23FEB0BE8ECF4B8AA40EB03B838DC
-:1030D00044894662F8C38A86AF00A802740A24FDB8
-:1030E000E88DFB0C02E888FBF8C3AC49E881FCF8EA
-:1030F000C390AC49E879FCF8C390E85CF57505E845
-:10310000E6FDF8C3E8CDFD36A0B41324103410E872
-:10311000260136A1B413A901007405E8FEFEEB0EEA
-:10312000A90200740432C0EB02B001E8E8FE36A147
-:10313000B413E8AB0B36A1B413C1E805250100E8D0
-:103140000CFF36A0B5132410E82BFD32C0368A26BA
-:10315000B513F6C4047409FEC0F6C4087402FEC0B8
-:10316000E8EFFD36A1B613250F00E803FC36A1B643
-:1031700013C1E804250300E888FC36A1B613C1E8B2
-:1031800005250200E8CDFC36A1B613F6C40175048E
-:1031900032C0EB0980E402D0ECB0022AC4E88CFC17
-:1031A00036F606B713407405E88DFEEB03E894FE8F
-:1031B00036F606B713207405E869FEEB03E870FEE7
-:1031C000F8C3F8C38B4638A9040075230D040089A1
-:1031D000463883C2088B462E3B463C7314834E38D8
-:1031E000108A86A70024FE8886A700EE83EA08F8E6
-:1031F000C38A86A7000C01EBEE908B4638A9040029
-:10320000740625FBFF894638F8C3AD4949E8BEFB83
-:1032100089868E00F8C3AD4949E8B2FB89869000E3
-:10322000F8C3834E2604E892FAF8C390836626FB1F
-:10323000E888FAF8C390AC4984C07507808EA30073
-:1032400004F8C380A6A300FBF8C3AC4983C2083CC2
-:1032500002760232C03C017412770B8A86A70024E2
-:10326000EF8886A700EE83EA08F8C38A86A7000CD9
-:1032700010EBEE905283C206B0BFEE5283C204AC94
-:1032800049EE5A8A86A800EE5AF8C3905283C206C5
-:10329000B0BFEE5283C208EBE690AC49F8C3AC492C
-:1032A000E8B4EE7303E8F7EEF8C38A86AF00247F34
-:1032B000E8BDF9B8F000E866F2816626FFF3E8237E
-:1032C000FAE8D2F9F8C3B88000E837F2804E270850
-:1032D000E811FAE8C0F9F8C3B88000E841F2816665
-:1032E00026FFF7E8FEF9E8ADF9F8C390B81000E85A
-:1032F00011F2804E2704E8EBF9E89AF9F8C3B81008
-:1033000000E8FFF1816626FFFBE8D8F9F8C3AC4975
-:10331000F8C383C2068A86A8000C408886A800EEFF
-:1033200083EA06F8C39083C2068A86A80024BFEB0E
-:10333000EA90AC498AE080C20AEC80EA0AA82074CC
-:10334000058AC4EEF8C30651578B4E24E3344989ED
-:103350004E24FF461A8E46028B7E228AC4AA897E9C
-:10336000228B462624FD89462675298A86A500A833
-:1033700002752180C2020C028886A500EE80EA0256
-:10338000EB12C47E003B7E1E760A4F268825897E7E
-:1033900000FF461A5F5907F8C390ACAD83E9038577
-:1033A000C074053D00207205B8FFFFEB03C1E003C8
-:1033B0003B8694007426898694008BD85283C2067B
-:1033C0008A86A8008AE00C80EE83EA068AC3EE8330
-:1033D000C2028AC7EE83C2048AC4EE5AF8C3B08818
-:1033E0008886BC00E88CF233DB8A86A500A80274CC
-:1033F0000380CB01A805740380CB02A80874038066
-:10340000CB04F686A70010740380CB108A86A9002F
-:10341000F6C304750A83C20CEC83EA0CC0E8048A84
-:10342000E08A86AF00A8807408F6C401750380CBDB
-:1034300020F686A70002750AF74638040074038058
-:10344000CB40889EBE00FE86B400B00AE8F3DBF8ED
-:10345000C3FE86B400B00AE8E8DBF8C3AC493C021E
-:103460007437771084C07406804E3801F8C38066C4
-:1034700038FEF8C38B463825FFF7894638A9000483
-:1034800075EA8A86A500A80175E20C0583C2028848
-:1034900086A500EE83EA02F8C3814E3800088A86CA
-:1034A000A500A80174C624FAEBE2AD4949F8C3901F
-:1034B000E811FAFE86B900B00EE886DBF8C3B0FF6B
-:1034C000E8BFECF8C39083667AFBB000E873DBF8E2
-:1034D000C390AC49E853D9721136881E1A0136A040
-:1034E0008E120AC352BA0001EE5AF8C3AC4932E454
-:1034F00036A38612050600368B1E88122BD8368915
-:103500001E8A12F8C390AD8BD8AD83E90403C32B98
-:103510004676894678F7467A0200740A83667AFD11
-:10352000B80000E81CDBF8C3061607AC49250F00FD
-:103530006BC0098DBEFD0003F8AC49250F00AA85BC
-:10354000C074082BC8518BC8F3A459E827F0E8448D
-:103550000307F8C333C0AC4936A3B21336A3B01384
-:10356000F8C383667AEFE82C03F8C390834E7A1091
-:10357000EBF4E89BF0F8C390AD3C19770E3C19775B
-:103580000A8BF881E7FF0088A6C400F8C390834E39
-:103590002620AC4932E4D1E08BD8C1E30203C389D1
-:1035A000466E834E4804B006E897DA4946F9C39060
-:1035B000FE86B300B00AE889DAF8C39033C0AC499C
-:1035C0006BC00A89868A00F8C390AC4932E43D0A90
-:1035D000007705B80A00EB083D5A007203B85A009C
-:1035E00051F7D80564008BC88B4644F7E1B96400F5
-:1035F000F7F189464659F8C3AC49E885EBF8C39022
-:10360000AC4984C07507816638FFFDF8C3814E3828
-:103610000002F74638400075088A86A9008886AA05
-:1036200000F8C3905156E87F0C5E59F8C390FE86AF
-:10363000B600B00AE80BDAF8C390FE86B700B00A0D
-:10364000E8FFD9F8C390FE86B800B00AE8F3D9F8CD
-:10365000C39000905155AC2EA2523633C9AD8BF9B0
-:10366000C1E705A9010074232E8BAD4400837E08B9
-:103670000074182E803E523601740960B004E8BB15
-:103680000C61EB0760B0FBE8EC0C614747D1E875D3
-:10369000D24183F90472C65D5983E905F746384083
-:1036A000007405E887EAF8C3E88DEAF8C39036C6E7
-:1036B00006C81301F8C333C0AC4936A38012AC4925
-:1036C000362B068812F7D836A38212F8C390DE266E
-:1036D000DE26EC26F226F826FE2604270E271627DD
-:1036E0001E2726272E273427BE34C634D2343A2745
-:1036F000782780279427A027B427C027D427E0273E
-:10370000F42700281028EC34DE261E2826282C2832
-:10371000322838284E288A28063528359828BE2889
-:10372000D228DE28E628543562356C35EE28C029CB
-:10373000C829CE29E02972357835F029FC298E3543
-:10374000082A122A1C2AB035362ABC355A2A622A7F
-:10375000682ACA357C2AF835882AA62AB82ACC2AAB
-:10376000DE2AF22A00360A2B242B2436382B4C2B47
-:10377000842B2E363A3646365436E82BAE36402C5D
-:10378000622CB6367028DE26DE26D42EE82EF02EE9
-:10379000F82E002F0A2F122F1A2F222F2A2F422FF6
-:1037A000BE34C634D234502F8C2F942FA82FB42F70
-:1037B000C82FD42FE82FF42F083014301C30EC34ED
-:1037C000DE2624303030383044304C306230A43083
-:1037D00006352835AA30CE30D630EA30F2305435AE
-:1037E00062356C35FA30C231C231C431FA317235CA
-:1037F00078350A3216328E3522322C323632B035D6
-:103800004A32BC3574328C329A32CA359E32F8351F
-:10381000AA32C632D832EC32FE320E3300361233C0
-:103820002633243632339A33DE332E363A36463652
-:1038300054365C34AE36AA34B034B6368C30E32815
-:10384000F7463840007532E8E3E833C0AC493D5BE9
-:103850000077198BD8D1E32EFF97CE36720B85C92E
-:1038600075E88B4648E81A0CC34E41C36A001FC670
-:103870000693120C9C0EE863DAE8BCE833C0AC494E
-:103880003D5B0077E78BD8D1E32EFF97863772D95F
-:1038900085C975E8C3F7467A1000750F83BE8400AA
-:1038A000007408B8483A89868000C381BE8000EC65
-:1038B0003C74F783BE8800007505B8EC3CEBE7F775
-:1038C000467A080075401E608B8E88003B4E7477E8
-:1038D000333B4E78772EC47E108BDF26033D47475F
-:1038E00033C08ED88DB6F4008BC1F7467A010075CF
-:1038F0001DF3A4260107294678014676294674B0AF
-:103900000CE83ED7611FC78688000000EBACE3E3FC
-:103910005090AC247FAAE2FA58EBD8908B8E8800A6
-:10392000E3468B9E8A0085DB743EBA50FFED2B8602
-:1039300082003BC372378DB6F400C47E108BDF2645
-:10394000033D47478BC1161FF7467A01007524F3E4
-:10395000A4260107294678014676294674C7868839
-:10396000000000B00CE8DAD683667AF7C3B000E84E
-:10397000D0D6C3E3DC50AC247FAAE2FA58EBD29055
-:103980001E6033C08ED88DB6FD008B8688008B9666
-:1039900084003A0475108BDE468BC88DBEF400F3AC
-:1039A000A674668BF39083C6094A75E68DB6FD0052
-:1039B0008B9684003A0473108BDE468BC88DBEF460
-:1039C00000F3A674768BF39083C6094A75E68DB62C
-:1039D000F400ACF7467A01007402247F1EC55E1025
-:1039E0008B37884002468937FF4E78FF4676FF4E78
-:1039F000741F8B8E880049898E8800E3438DB6F44E
-:103A0000008BFE46F3A4E97DFFC576108B1C85DB99
-:103A1000740803F383C60383E6FE8B8684002BC2FF
-:103A2000B48089044646C7040000897610834E7A24
-:103A300004C78688000000611FF9C333C0611FC33B
-:103A4000B08084C0611FC3908B4E782B8E88007627
-:103A50002789B68C008B5E743BCB72028BCB3BC844
-:103A600072028BC88BC1E34433D28EC28BD183BE2A
-:103A70008800007406E98E0033C0C38B5E10031FFC
-:103A8000434352F7467A0100752AAC8DBEE4008BA1
-:103A90008E8600F2AE74348807434A75ED588B5E0B
-:103AA0001001072946780146762946748BC62B8675
-:103AB0008C00C390AC8DBEE4008B8E8600F2AE7499
-:103AC0000A247F8807434A75EBEBD28886F400C747
-:103AD0008688000100582BC2740E8B5E10010729E6
-:103AE000467801467629467440E894FE72BE4A75CF
-:103AF0001583BE8A000074B4BA50FFED8986820037
-:103B0000834E7A08EBA68DBEF40003BE8800A4FFA6
-:103B1000868800E86AFE729479064A748FE95BFF32
-:103B20004A74CEEBE19050E811CC8B467439467262
-:103B300074271E565133C9C5760CAD74107809032D
-:103B4000C805010024FE03F03B761076ED294E7681
-:103B5000014E78E837CC595E1F58C390C47E1026BA
-:103B60008B1D83C30326891D4B03FBAB91AAB803AE
-:103B700000294678014676294674C390C47E1026F3
-:103B80008B1D4326891D4303FBAAFF4E78FF467613
-:103B9000FF4E74C3E8E5FFC38081848582838687F6
-:103BA00050538ADC83E30ED1EB2E8A87983B08863C
-:103BB000B000FE86B100B00AE887D45B58C3508AD3
-:103BC000C8B8FF00E895FF58C3908A86BB00E8ABF1
-:103BD000FFC3E8CBFFE8F2FFC390E8C3FFE8B4FF00
-:103BE000C39033C0E895FFC3B8FF0033C9E86CFF4A
-:103BF000C390B8FF01B110E862FFC390C3FC3BE281
-:103C00003BF23BF23BFC3BE23BE83BE83BFC3BE26C
-:103C10003BE83BE83BFC3BE23BE23BE23B00100085
-:103C20000000100000001000000010000000100054
-:103C3000000010000000100000001000000008004C
-:103C40000000080000000800000008000051538B2D
-:103C50004E3881E1FFEEA804740481C900018AE0B6
-:103C600080E4032418D0E40AC433DB8AD82E8B877F
-:103C7000FD3B89467C2E0B8F1D3C894E38D1EB2EA7
-:103C80008AA73D3C5B59C3AC493C01721D74203C82
-:103C900003722374283C08722B74303C20723774F2
-:103CA0003ABBDA3B32E4895E7EC3BBA03BEBF5BB9B
-:103CB000943BB401EBF0BBFC3BB402EBE9BBE23B51
-:103CC000B403EBE2BBBE3BB404EBDBBBCA3BAC4989
-:103CD0008886BB00EBCEBBD23BEBF3BBFC3BEBC41B
-:103CE000A9040075D1A9080075DAEBD18B5E748B3D
-:103CF0004E783BCB72028BCB3BC872028BC88BC118
-:103D0000E32CC47E108BDF26033D4747F7467A013C
-:103D100000751CF7C70100740249A4D1E9F3A5732B
-:103D200001A4260107294678014676294674C35026
-:103D300053BB7F7FF7C70100740549AC22C3AAD1EA
-:103D4000E9E31D9CAD23C3AB497414AD23C3AB4958
-:103D5000740DAD23C3AB497406AD23C3ABE2E59D3F
-:103D60007304AC22C3AB5B58EBB8E8CEC98B5E38AA
-:103D7000F7C310047501C3F7C340007405E8B8E346
-:103D8000EB03E8A8E3816638EFFBF6C310743CF65A
-:103D9000C3027406E4D80C01E6D8F6C30474118398
-:103DA000C2088A86A7000C01EE8886A70083EA086D
-:103DB000F6C308740FE88BE3720A8A86C000E638FF
-:103DC000B023E60AF7C300047501C3F7C300087502
-:103DD000F98A86A500F6C340750DA81075EC0C1085
-:103DE0008886A500E60CC3A80175DF83C2020C0516
-:103DF000EE8886A500C3B000E847D2EB0FB002E81A
-:103E0000900EEB08836638DF834E7A0233C08ED87B
-:103E1000FAA0921240A292123C05721EC60692129D
-:103E200000FBB001E86B0EFAA1260123062A01A8C7
-:103E3000017507E8E207E8610990B000E837D2FBB6
-:103E400085ED74B9FAF7467A460075C08B46783D21
-:103E50000A0072B08B4E7483F950729A836638DF11
-:103E6000C576148B463A85C07558AD85C0750FE888
-:103E7000F8FEF7467A08007493E8A0FAEB8E3B76DA
-:103E8000047621B90200394E2E7705C7462E000070
-:103E9000568B762C897604C7040000464689762C1A
-:103EA000294E2E5E85C07917F6C4107405FF567C26
-:103EB000EB03FF567E897614B00CE885D1EB86893A
-:103EC000463AFF96800029463A897614B00CE8718C
-:103ED000D1E971FF0000000000000000080410029A
-:103EE00001200000000000000000000000000000B1
-:103EF00000000000808080808080808080808080C2
-:103F000080808080808080808080808080808080B1
-:103F100080808080808080808080808080808080A1
-:103F20008080808080808080808080808080808091
-:103F30008080808080C0C0C0C0C0C0C0C0C0C0C0C1
-:103F4000C0C0C0C0C0C0C0C0C0C0C0C0C0C0C080B1
-:103F500080808000808080808080808080808080E1
-:103F60008080808080808080808080808080808051
-:103F70008080808080808080808080808080808041
-:103F80008080808080808080808080808080808031
-:103F90008080808080808080808080808080808021
-:103FA0008080808080808080808080808080808011
-:103FB0008080808080808080808080808080808001
-:103FC00080808080808080808080808080808080F1
-:103FD000808080804E417841D041F44106421842B1
-:103FE000C3908E46028B7E22897E6C806627FD8B75
-:103FF000562483FA0472E983EA028BD93BCA76021B
-:104000008BCAB00A57518BFEF2AE8BC1595F751E39
-:1040100050402BC874062BD12BD9F3A4594B4A4AD4
-:10402000B00DAAA43BCA76028BCAE313EBD42BD9FA
-:10403000F7C601007402A449D1E9F3A57301A4896C
-:104040007E222B7E6C297E24017E1A8BCB807E26DD
-:10405000027405806626FDC360B0FDE8180361C3E5
-:10406000C390E87C0272F990834E26208B466A89C1
-:10407000466E8B46480D040025BFFF894648B006B2
-:10408000E8BFCFC3897E222B7E6C017E1A297E2455
-:10409000807E26027405836626FDC360B0FDE8D5E8
-:1040A0000261C3908ABEC200EB24F7464840007507
-:1040B000B18E46028B7E22897E6C8B562483EA0A5F
-:1040C000789E03D7806627FD33C08ABEC200E3B462
-:1040D0003BFA77B0AC49932E8A87D43E9322DF75A2
-:1040E00017AAE3A03BFA779CAC49932E8A87D43E6B
-:1040F0009322DF7503AAEBD6F6C37F7505FF4666EC
-:10410000EBDFF6C340750C8BD883EB08D1E32EFFB1
-:10411000A7D43FFF46662C20EBC785C0742C894688
-:104120006A834E4840897E222B7E6C017E1A297E4E
-:1041300024807E26027408836626FDE8A301C360FE
-:10414000B0FDE8310261E89801C3E957FF908B5E4A
-:10415000664B7803895E66AA8B5E64F7C3002075A0
-:1041600003E940FFF7C3400074088A86C100AAE94A
-:1041700032FFB83200EBA3908B5E66895E6883C322
-:104180000880E3F8895E668B5E6481E3001881FB3A
-:104190000018742DAA85DB7425F746644000751855
-:1041A00081FB0010740C8B46662B4668C1E004E965
-:1041B00068FFB86400E962FF8A86C100AAAAE9E341
-:1041C000FE518B4E662B4E68B020F3AA59E9D4FEFF
-:1041D0008B5E66895E688B5E64F7C324007410C7CB
-:1041E00046660000F7C304007405B00DAAB00AAA21
-:1041F000EB489090AAF7466400407406B8D007E9EF
-:1042000018FFE99FFE90AAF7466400807406B8D0B4
-:1042100007E906FFE98DFE908B5E66895E6885DBA7
-:10422000750C8B5E64F7C310007406E976FE8B5E36
-:1042300064F7C308007427B00AAAF7C32000751FEB
-:10424000F7C300017503E95BFEF7C340007506B8CC
-:104250006400E9C5FE8A86C100AAAAE946FEAAC78B
-:1042600046660000F7C3000674F1F7C340007419F6
-:104270008A86C10081E3000681FB00047206760293
-:10428000AAAAAAAAAAAAE91BFE81E3000681FB004A
-:1042900004720E7606B89600E97FFEB86400E979EC
-:1042A000FE8B4668E973FE90368B0EDA1283F93284
-:1042B000731D1E0633C08ED88EC08D764CBFDC12A7
-:1042C00003F9A5A5A583C106890EDA12071FC3B09D
-:1042D00008E86ECDC390836648FEE893C4E8C8FF43
-:1042E000C3F6462702750F9CFA837E1A0074098074
-:1042F0004E27019DF9C3F8C35052F7463840007469
-:104300001DE834DE83C20AECA840752783EA088AD8
-:1043100086A5000C028886A500EE5A58EBD1E80C61
-:10432000DE8A86A50024FB0C028886A500E60C5ACE
-:1043300058EBBC804E27025A589DF8C30846269C6D
-:10434000FA8A8EA500F7463840007514F6C1067447
-:1043500023E8D9DD8AC124F98886A500E60C9DC32F
-:10436000F6C102740FE8D0DD83C2028AC124FD8841
-:1043700086A500EE9DC38B5E2622C3884626740167
-:10438000C3806627FD9CFA8A8EA500F74638400058
-:104390007516F6C104750FE893DD8AC124FD0C047F
-:1043A0008886A500E60C9DC3F6C10275F9E888DD94
-:1043B00083C20AECA820750E83EA088AC10C028821
-:1043C00086A500EE9DC383EA0A33C98A4E1C8B463C
-:1043D0001A3BC8731B014E2A2BC189461A1EC5768B
-:1043E00000F36E1F89760083C2028A86A500EBCD9A
-:1043F00085C0741201462A8BC81EC57600F36E1F55
-:10440000897600894E1AF6C701752380CB02895E32
-:1044100026E808C383C2028A86A50024FDEE8886AA
-:10442000A500F6C7107505B002E816CC9DC383C27F
-:10443000028A86A500EB86908BD18B46243BC876FA
-:10444000028BC82BD12BC18BD9E322806627FD8E2E
-:1044500046028B7E22F7C601007402A449D1E9F31B
-:10446000A57301A4897E22894624015E1A8BCA8025
-:104470007E26027405806626FDC360B0FDE8F6FE68
-:1044800061C350E40A84C0750A8686A10084C074A2
-:104490000AE60A580C20894648F9C35824DF8946A1
-:1044A00048F8C390FBB002E8E807FAE82E01FBB039
-:1044B00001E8DE07FAB002E8BCCBFB85ED74E5FA53
-:1044C0008E5E0AFB90FA8B46488B7640A88C75DE90
-:1044D000A820741A50E855DC58E8A6FF7310B00203
-:1044E000E85FCBEBC99025FF008BC8EB3690A801A5
-:1044F00075224683E6FE3B76087479AD8AFCB3F0FC
-:1045000022FB3AFB74E03ABEA000742EE8D2FD73A1
-:1045100077EB9B908AE024FC8846488B4E4AF6C491
-:1045200002741DE8BBFD7286E813F3897640E393BD
-:10453000834E4803894E4AE974FF25FF0F8BC890CC
-:104540008B86980085C0741A518A8EA000C0E90439
-:10455000BA0100D3E25923C2740803F1897640E915
-:1045600061FFFF5662E3F5834E4801894E4A897622
-:1045700040E93AFF814E2600108B46503B46467775
-:1045800003E852FDE927FF9088BEA000EBAC0A06C5
-:1045900090128AE0BA0601B004EEEC84C07512B045
-:1045A00004EE8AC4EE32E4A8807406C706841200C2
-:1045B0000088269012C30A0690128AE0BA0601EC1F
-:1045C000A80175EDBA08018AC4EE32E4A88074E14E
-:1045D000C7068412000088269012C39036F706247E
-:1045E0000101007530368B0EDA1280F936732633EE
-:1045F000C08EC08ED8BFDC1203F9B008E877CA8538
-:10460000ED740E8D764CA5A5A580C10680F9367295
-:10461000E9890EDA12C3C390F7062601010075F688
-:104620008B0E201385C975EE33C08EC08ED8BF2483
-:1046300013B93600B00AE83DCA85ED7506E91201E6
-:10464000E90A0133DB8A464C8AA6B300FECC780E19
-:1046500088A6B3000ADCB40AAB83E90276E28AA634
-:10466000B200FECC780E88A6B2000ADCB408AB8398
-:10467000E90276CC8AA6B100FECC78188ABEB000DA
-:10468000750488A6B00088A6B1000ADC8AE7AB836F
-:10469000E90276AC8AA6B400FECC781F88A6B400E6
-:1046A0000ADCB40BAB8A86BC008AA6BD00AB8B8645
-:1046B000BE00AB83E90676888A464C8AA6B600FE21
-:1046C000CC781988A6B6000ADCB40CABE8DBCBAB1F
-:1046D0008B462AAB83E90676748A464C8AA6B700D5
-:1046E000FECC781988A6B7000ADCB40DABE8BACBCB
-:1046F000AB8B4634AB83E90676538A464C8AA6B820
-:1047000000FECC781988A6B8000ADCB40EABA15024
-:1047100012ABA15212AB83E90676328A464C8AA6C6
-:10472000B500FECC781888A6B5000ADCB40FAB8BB8
-:10473000869A00AB8B869C00AB83E906760F84DB00
-:104740007503E9EFFEB00AE8F8C8E9E7FEB00AE849
-:10475000F0C8F7D983C1368BC10D800086C4A3226F
-:10476000134141890E2013C3A184122BC17211A3DE
-:104770008412BE2213D1E9F36F90890E2013F8C37F
-:10478000F9C3C381EF6A1374F98BC70D800086C427
-:10479000A368134747893E6613C3F7062A01010041
-:1047A00075E08B0E6613E30780F92077D54949330E
-:1047B000C08EC08ED8BF6A138BF703F983C6343B13
-:1047C000FE77C0B00EE8AEC885ED74B78A464C8A55
-:1047D000B6B900FECE781588B6B9008AA6A90080C1
-:1047E000CCC0AB84F67405B00EE856C88AB6BA00E1
-:1047F000FECE78CB8A9EA9008ABEAB008A563F8A3D
-:10480000F332F70AB6AC00C686AC000022F2744B55
-:10481000F6C608740FB402F6C3087502B403AB8081
-:10482000E6F77437F6C601740FB400F6C3017502DB
-:10483000B401AB80E6FE7423F6C602740FB404F62E
-:10484000C3027502B405AB80E6FD740FF6C60474AE
-:104850000AB406F6C3047502B407ABC686BA0000F4
-:10486000889EAB00E958FF90A184122BC17211A35E
-:104870008412BE6813D1E9F36F90890E6613F8C3F2
-:10488000F9C3A1841241412BC17223A384128BC1AD
-:10489000484832E40C8086C4EF9090909090BEDC43
-:1048A000124949D1E9F36F90890EDA12F8C3F9C3BE
-:1048B0008AC88A464CB40183EB06EF9090909090A2
-:1048C000B80100EF90909090908AC1EF90909090F6
-:1048D00090E99700E9AC0033C08ED8891E8412C3DA
-:1048E000368B1E8412FB90FAB00CE889C785ED74F4
-:1048F000E6C5760C83FB1472DBFB90FAAD85C078BD
-:10490000AF74E28BFE03F8368B0E86123BC1770242
-:104910008BC883EB043BD977028BCB33C08A464CE0
-:10492000EF90909090908BC1EF90909090904180FC
-:10493000E1FE2BD951D1E9F36F90598BC74024FE8A
-:104940003BC674272BFE4E4E538B5E103BF3721307
-:10495000031F83C30380E3FEC7070000836E740256
-:10496000895E105B893C89760CEB8989760C3976F7
-:104970001077817208833C007403E977FFE80DBE6D
-:10498000E962FF36891E8412B00CE8B5C633C08ECA
-:10499000D8C3A184123D10007277BA04013B068887
-:1049A000127506C7067E1200008B0EDA12E30BE8C2
-:1049B000D0FE7257C7067E12FF7F8B0E2013E30BCB
-:1049C000E8A5FD7246C7067E12FF7F8B0E6613E3D5
-:1049D0000BE894FE7235C7067E12FF7FA12801A95D
-:1049E00001007503E8F9FE803E8D1200751DA1845B
-:1049F000123D200076153B0682127609A17E123BFD
-:104A0000068012720C800E901280C3B080FF167C5C
-:104A100012C3800E901240C36A001FC6069312177D
-:104A20009C0EE8B7C86A001FC6069312209C0EE8C9
-:104A3000AAC86A001FC6069312169C0EE89DC8906D
-:104A4000BA0601ECA82075CAFB90FABA0401ED90F1
-:104A5000909090903A06941277BE33DB8AD8D1E3D7
-:104A60002E8BAF4400C47E0885FF74B9F6C4C075B0
-:104A70005532C0C1E00280E4F08BF0ED9090909050
-:104A80009085C074BB8BC84180E1FE0BC68B5E5025
-:104A90004B4B2BD9789CAB8BC1404001464ED1E9A2
-:104AA000F36D90895E50897E088B462680E4EF89FD
-:104AB0004626F6C401750CF746480C007505B00291
-:104AC000E87FC5E97AFF86C48BC883E13F4180E176
-:104AD000FEE30A3C807209243FB4F0EBB0E960FFCA
-:104AE000253F0033FF8EC7BF96128BF7D1E9F36DD8
-:104AF000908BC8E848EDE947FF906A001FC606930F
-:104B0000121B9C0EE8D5C790601E0633C08ED88E4F
-:104B1000C0BA0601ECA80474E1B006EEECA28C1257
-:104B2000A8407411A18812A38412C6068D1200E851
-:104B300060FEA08C12A8807403E804FFB80080BA5D
-:104B400022FFEF071F61CF906A001FC60693121B5A
-:104B50009C0EE887C790601E0633C08ED88EC0BA00
-:104B60000601ECA80474E1BA0801ECA28C12A8407A
-:104B70007411A18812A38412C6068D1200E812FED9
-:104B8000A08C12A8807403E8B6FEB80080BA22FF99
-:104B9000EF071F61CF90EE86E0EE86E0EC86E0EC5A
-:104BA00086E080E1FEF36C9080E1FEF36E900500FC
-:104BB0007547A84B05007548A84B0500A348A84BAE
-:104BC00005003549A84B06009848964B0600BA48A0
-:104BD000964B0600C348964B0600CB48964B060002
-:104BE0002049964B06002849964B06004E4A9C4B9E
-:104BF00006007B4A9C4B05009E4AA24B0500EC4AEE
-:104C0000A24B00001E06833E4412007409A0060158
-:104C100024303C30741A8CC88ED88EC0BBAE4B8BFF
-:104C20000FE30D8B7F028B7704F3A483C306EBEFB6
-:104C3000071FC39033C0A33E01B90C01BE40018BD6
-:104C4000FE81C6B40F89048BC62BF13BC777F6A350
-:104C50003C01C3901E0660368B2E3E018B5E003BEE
-:104C6000EB742B8B7602891C89770236A13C018973
-:104C7000460036892E3C018BEBFF4E0674088B6E86
-:104C800000FF4E0675F836892E3E018B66046107DB
-:104C90001FC31E0660368B2E3E0198894606896624
-:104CA000043B6E0074108B6E00FF4E0675F836895B
-:104CB0002E3E018B660461071FC3C3901E06609CD5
-:104CC000FA33ED8EDD8B2E3C0185ED743D8B4E006D
-:104CD000890E3C018BCC8DA60A01561E06608966A2
-:104CE00004C746080F1AC7460601008B1E3E018501
-:104CF000DB741D8BC58707894600895E028BD889C6
-:104D00006F028BE19D61071FF8C39D61071FF9C307
-:104D1000892E3E01896E00896E0287E19D8BE1EB51
-:104D2000E4000D0A5465726D696E616C73207375D1
-:104D300070706F727465643A0D0A312920414E53C8
-:104D40004920636F6D70617469626C650D0A322968
-:104D500020577973652033300D0A506C6561736597
-:104D60002073656C6563743A20000D0A636F646597
-:104D7000207365676D656E743D000D0A4D6F6E6939
-:104D8000746F722076322E350A0D0A3E000D0A50DD
-:104D90006172646F6E3F000D0A4E6F206164647231
-:104DA00065737320737065636966696564000D0AD5
-:104DB0003A000D0A004C6F633D000D0A4641544114
-:104DC0004C204552524F523D000D0A4D6F6E697492
-:104DD0006F7220636F6D6D616E64733A2D0D0A20E2
-:104DE0002020442C645B5B787878783A5D7878781A
-:104DF000785D202D2064756D70206D656D6F727902
-:104E00000D0A2020204C2C6C5B5B787878783A5D1A
-:104E1000787878785D202D2064756D702073696EC8
-:104E2000676C65206C696E650D0A202020452C6535
-:104E30005B5B787878783A5D787878785D202D209B
-:104E400065646974206D656D6F72790D0A2020208C
-:104E5000462C665B5B78787878205D787878785D2A
-:104E6000202D2066696C6C206D656D6F72792070E5
-:104E70006172616772617068730D0A202020495B5E
-:104E8000787878785D202020202020202020202D78
-:104E900020776F726420696E7075742066726F6D12
-:104EA00020706F72740D0A202020695B7878787802
-:104EB0005D202020202020202020202D20627974B9
-:104EC0006520696E7075742066726F6D20706F72E8
-:104ED000740D0A2020204F78787878207878202068
-:104EE000202020202020202D206F757470757420C4
-:104EF000776F726420746F20706F72740D0A2020B7
-:104F0000206F787878782078782020202020202042
-:104F100020202D206F75747075742062797465205F
-:104F2000746F20706F72740D0A202020475B5B78CD
-:104F30007878783A5D787878785D2020202D206721
-:104F40006F746F20616464726573730D0A20202092
-:104F5000575B5B787878783A5D787878785D202050
-:104F6000202D207761746368206120776F72640D53
-:104F70000A20202043202020202020202020202024
-:104F800020202020202D20696E7465727275707447
-:104F900073206F66660D0A202020532020202020D9
-:104FA00020202020202020202020202D20696E7409
-:104FB00065727275707473206F6E0D0A20202073F5
-:104FC00020202020202020202020202020202020E1
-:104FD0002D2073696E676C6520737465700D0A20EF
-:104FE000202042787878782020202020202020203F
-:104FF0002020202D20627265616B706F696E7420B5
-:105000007365740D0A20202062202020202020209B
-:105010002020202020202020202D20627265616B1E
-:10502000706F696E7420636C6561720D0A202020B8
-:10503000522020202020202020202020202020203E
-:10504000202D207265737461727420627265616BC9
-:10505000706F696E740D0A2020207220202020209D
-:1050600020202020202020202020202D2072656755
-:105070006973746572732061742062726B70740D51
-:105080000A202020582C78206E202020202020204C
-:1050900020202020202D206578616D696E652063B9
-:1050A00068616E6E656C206E0D0A202020482C3FD2
-:1050B00020202020202020202020202020202D20E3
-:1050C00074686973206D657373616765001B5B327B
-:1050D0004A1B5B313B3148414E5349205465726D48
-:1050E000696E616C0D0A0A001B5B4B001B5B4A007A
-:1050F0001B5B324A1B5B313B3148001B5B44201B6E
-:105100005B44001B5B313B373248001B5B003B00BC
-:1051100048001B5B73001B5B75001B7A2B0B7F1B0E
-:105120007A2E0C7F1B7A2D087F1B7A2C0A7F1B7A24
-:1051300022087F1A57797365203330205465726DC9
-:10514000696E616C0D0A001B54001B59001A001E89
-:105150000008200800001B3D0000001B46000D0059
-:105160003F4464456546664767486849694F6F43F1
-:1051700063537342625272577758784C6C3C60D4D8
-:1051800057D45750585058D659D659B459B4593C99
-:10519000603C606C57485726570657905790579871
-:1051A00057485F0C5F585F335F405FA057A057FEC2
-:1051B00059FE59DC57DC5788619861C061CC61D8D1
-:1051C00061F66102622262F8564A625862605920B2
-:1051D00020666C6167733D00202061783D002020CF
-:1051E00062783D00202063783D00202064783D00F7
-:1051F000202063733D00202064733D0020206573F0
-:105200003D00202073733D00202064693D00202074
-:1052100073693D00202062703D00202073703D00C6
-:10522000202069703D00206368616E656C3D002040
-:105230002020207365673D002074695F7374723DA0
-:10524000002074695F746F733D002074695F6D6145
-:10525000783D002074695F6261733D002074695F6E
-:1052600073697A3D002074695F7374663D00207431
-:10527000695F726F6F3D002074695F666C673D0007
-:105280002074695F746F743D002072695F70636E93
-:105290003D002072695F7374723D002072695F7314
-:1052A00074663D002072695F726F6F3D0020726905
-:1052B0005F6261733D002072695F73697A3D00200F
-:1052C00072695F746F743D002072695F6D696E3D35
-:1052D000002072695F666C673D002072695F746FC1
-:1052E000733D002072695F7468723D002074685FCE
-:1052F0007374663D002074685F7374723D0020749F
-:10530000685F6261733D002074685F73697A3D0075
-:105310002074685F7472673D002074685F666C6714
-:105320003D002074685F636E743D002072685F7397
-:1053300074723D002072685F7374663D002072686D
-:105340005F6261733D002072685F73697A3D00207F
-:1053500072685F7370613D002072685F61736F3DBA
-:10536000002072685F726F6F3D002072685F666C2C
-:10537000673D00206D5F636172653D002070745F62
-:10538000666C6F3D002061735F666C6F3D0020723C
-:105390006D5F666C6F3D00202020715F696E3D007F
-:1053A0002020715F6F75743D0020715F6472616EC3
-:1053B0003D002020715F74696D3D00202020715FE9
-:1053C00066633D0020715F737461743D0020715FFE
-:1053D000646174613D0020715F6D6F646D3D0020FC
-:1053E00068616E645F6F3D002068616E645F623D5E
-:1053F000002068616E645F653D002068616E645FD7
-:10540000693D0020206F706F73743D002020746927
-:105410006D656F3D0020637573746D313D002063D1
-:105420007573746D323D0020637573746D643D0057
-:10543000207478726174653D0020727872617465C1
-:105440003D002020635F6D61703D0020635F6164FB
-:1054500064723D0020635F616973723D0020635F89
-:10546000787461673D0020635F646566723D00206B
-:10547000635F666C73683D002074786D6178733D7E
-:10548000002072695F656D733D002020635F6C735F
-:10549000723D002020635F6965723D002020635FDC
-:1054A0006663723D002020635F6D63723D002020C3
-:1054B000635F6C63723D002020635F6473733D0023
-:1054C00020635F647373693D0020635F647373726C
-:1054D0003D002020635F6973723D002020635F639D
-:1054E00061723D002020635F6566723D0020635F4E
-:1054F000657273743D0020635F65636E743D0020C8
-:10550000635F62726B633D0020635F626F6B633D3C
-:105510000020635F7265706C3D0020635F6363739E
-:10552000723D0020635F737474313D0020635F73CC
-:105530007474323D002BC08ED88EC0E8C200E8E5FE
-:1055400000FABF8400C705DC568C4D02BF0C00C7B3
-:10555000056E5E8C4D02BF0400C705BA5E8C4D021D
-:10556000E8F10090E84901E81600F490E8E500BE93
-:10557000BA4DE8090CA09312E85D0CE8C209EBE40F
-:10558000E8D50CE8C40C0AC074F68B1EF8793C0D03
-:10559000742E3C0874173C7F741383FB207FE188D2
-:1055A00087D67943891EF879E8770CEBD30BDB7447
-:1055B000CF4B891EF8798B36167AE8C10BEBC19078
-:1055C000E80200EBBBC687D679000BDB741EA0D6C1
-:1055D00079BF6051B91D008BD9060E07F2AE077571
-:1055E00017412BD9D1E32EFF977D519033C0A3F8FB
-:1055F00079BE894DE8870BC3BE8D4DE8800BEBEC7F
-:10560000BA0002B093EEB055EEBA1002B093EEB00D
-:10561000AAEEBA0002EC3C557508BA1002EC3CAA9E
-:105620007403E82FF6C3BA0402B01AEEB020EEB04D
-:1056300030EEB040EEB080EEBA0002B013EEB0072C
-:10564000EEBA0802B080EEBA0202B0BBEEBA0402B3
-:10565000B005EEC3C606CA1301C706F8790000C636
-:1056600006F67901C706D0790000C706D279000096
-:10567000C706D4790000C706FA790000C706FC798E
-:105680000000C706FE790000C706007A0000C706C2
-:10569000027ACE598C0E047AC706067A0000C70635
-:1056A000277A0000C606297A00C6062A7A00C39027
-:1056B000BE224DE8C80AE83F002C313C0177F7E8EC
-:1056C00081098B360C7AE8B50ABE6A4DE8AF0A0E3E
-:1056D00058E8F80ABE7A4DE8A40AC39060D1E38383
-:1056E000FB1873111EBA00008EDA2EFF97B7518B8C
-:1056F000EC8946101F61CF90E84F0B0AC07505E892
-:10570000560BEBF4C390833EF879017416BED7793B
-:10571000E8310A8BD0AC3C2C74043C207505E8239E
-:105720000AEEC3E9D2FE833EF8790174F6BED7795A
-:10573000E8110A8BD0AC3C2C74083C207404E9B707
-:10574000FE90E8FF09EFC3908B16067A833EF87946
-:1057500001740BBED779E8EB098BD0A3067AB02091
-:10576000E8570B8B16067AECE86F0BC38B16067A9C
-:10577000833EF87901740BBED779E8C7098BD0A3B3
-:10578000067AB020E8330B8B16067AEDE8670BC378
-:10579000FAC606F67900C390C606F67901FBC390F7
-:1057A00006E85809B020E8110B268B05E8470BB036
-:1057B00008E8060BE8030BE8000BE8FD0AB8010057
-:1057C000E8CFF4BA0202EC24017502EBDCBA06025F
-:1057D000EC07C390C706087A1000EB06C706087AE4
-:1057E0000100068E06FC798B3EFA79E80E09E80B7B
-:1057F00000893EFA798C06FC7907C390BEB24DE869
-:105800007C098B16087A52E82A09E80F0AE80C0A84
-:1058100033DBB9100090268A01E8BC09E8FD094392
-:10582000E2F4E8F709E8F40933DBB9100090268ABE
-:10583000013C2072053C7E760390B02EE8E30943DC
-:10584000E2ECBEB24DE8360983C7105A4A75B7C3B9
-:10585000068E06007A8B3EFE79E8A008893EFE7926
-:105860008C06007A578B360E7AE81209C706087A3A
-:105870001000BA0002E8E800E881FF5FBA0000E823
-:10588000DE00BEB54DE8F6088CC0E83F09B03AE846
-:1058900090098BC7E83509E87E08E8C30090E8B7AF
-:1058A00009E8A6090AC074F63C0B750683EF10EBF5
-:1058B00019903C0A750683C710EB0F903C0C7504D9
-:1058C00047EB07903C0875244F908B36FE798BC7C9
-:1058D0002BC63D000172A53D1001720483EE20909D
-:1058E00083C6108936FE79578BFEEB803C2E7508F7
-:1058F000BA0113E86A0007C3C6060A7A0232C990E1
-:105900003C30724C3C39760C245F3C4172423C4640
-:10591000773E2C072C3050E8CC085802C8FE0E0AFF
-:105920007A740FC0E104E82F09E81E090AC074F672
-:10593000EBCE26880DE8E0078AD0E823008AC13C38
-:105940002072053C7E760390B02EE8D508E970FF02
-:10595000E8C507E80A00268A05E87C08E91DFF90EB
-:10596000F606267A02750286F2528B361A7AE80D0E
-:10597000085A528AC60206247AF606267A01750665
-:10598000E89F08EB0D9032E4E80D088B361C7AE8AE
-:10599000EC075A8AC20206257AF606267A017506AF
-:1059A000E87F08EB069032E4E8ED078B361E7AE8D4
-:1059B000CC07C390068E06047A8B3E027AE83C0739
-:1059C000893E027A8C06047A07FF1E027AC3BE97CC
-:1059D0004DE8AA07CB900657BED779E866078BD863
-:1059E000E861078BC82BCB78118EC3BF0000B8FFCE
-:1059F000FF51B90800F3AB59E2F75F07C39006BE49
-:105A0000D779E83F078BD8D1E32E8B9F4400BE2681
-:105A100052E8F1088BC3E8DD08B80100E873F2E84A
-:105A2000E008BE2F52E8DD088B4718E8C808BE77AB
-:105A300052E8D1088B4726E8BC08BE5352E8C50897
-:105A40008B471EE8B008BE5C52E8B9088B4720E8D7
-:105A5000A408BE6E52E8AD088B4724E89808BE80C3
-:105A600052E8A1088B472AE88C08E89508BE38520E
-:105A7000E892088B07E87E08BE4152E887088B470A
-:105A80001AE87208BE4A52E87B088B471CE8660891
-:105A9000BE6552E86F088B4722E85A08E86308BEE3
-:105AA000D152E860088B4738E84B08BEAD52E85445
-:105AB000088B4730E83F08BEB652E848088B4732AB
-:105AC000E83308BEA452E83C088B472EE82708BEFE
-:105AD000BF52E830088B4734E81B08E82408BE8929
-:105AE00052E821088B4704E80C08BE9252E81508DA
-:105AF0008B4714E80008BE9B52E809088B472CE846
-:105B0000F407BEC852E8FD078B4736E8E807BEDA5F
-:105B100052E8F1078B473AE8DC07BEE352E8E507B5
-:105B20008B473CE8D007E8D907BE1953E8D6078B66
-:105B30004748E8C107BEFE52E8CA078B4742E8B5AE
-:105B400007BE0753E8BE078B4744E8A907BE7C534E
-:105B5000E8B2078B474CE89D07BE8553E8A6078B44
-:105B6000474EE89107BE8E53E89A078B4750E88569
-:105B700007E88E07BE2253E88B078B474AE8760773
-:105B8000BEEC52E87F078B4708E86A07BEF552E88B
-:105B900073078B4740E85E07BE1053E867078B47E3
-:105BA00046E85207E85B07BE6A53E858078B477A16
-:105BB000E84307BE3D53E84C078B4770E83707BE04
-:105BC0004653E840078B4772E82B07BE4F53E83433
-:105BD000078B4774E81F07E82807BE2B53E8250703
-:105BE0008B470CE81007BE3453E819078B4710E8C1
-:105BF0000407BE5853E80D078B4776E8F806BE61E8
-:105C000053E801078B4778E8EC06BE7353E8F506C6
-:105C10008B473EE8E006E8E906BE9753E8E6068BC8
-:105C20004752E8D106BEA053E8DA068B4754E8C5D0
-:105C300006BEA953E8CE068B4756E8B906BEB25356
-:105C4000E8C2068B4758E8AD06BEBB53E8B6068BE4
-:105C5000475AE8A106BEC453E8AA068B475CE895FC
-:105C600006E89E06BECD53E89B068B475EE8860697
-:105C7000BED653E88F068B4760E87A06BEDF53E84E
-:105C800083068B4762E86E06BEE853E877068B47CB
-:105C90007CE86206BEF153E86B068B477EE8560649
-:105CA000BEFA53E85F068B878000E84906E8520693
-:105CB000BE4254E84F068B879E00E83906BE035467
-:105CC000E842068B4764E82D06BE0C54E836068B86
-:105CD000476EE82106BE1554E82A068B878E00E839
-:105CE0001406BE1E54E81D068B879000E80706BE0A
-:105CF0002754E810068B879200E8FA05E80306BEF1
-:105D00003054E800068B879400E8EA05BE3954E871
-:105D1000F3058B879600E8DD05BE6F54E8E6058B3A
-:105D2000879800E8D005BE5D54E8D9058A87A000B1
-:105D3000E8A705BE5454E8CC058A4728E89B05BE71
-:105D40006654E8C0058A87A100E88E05E8B305BE61
-:105D50007854E8B0058A87A200E87E05BE8154E841
-:105D6000A3058A87A300E87105BE8A54E896058AD0
-:105D700087A400E86405BE9354E889058A87A500D6
-:105D8000E85705BE9C54E87C058A87A600E84A05CA
-:105D9000BEA554E86F058A87A700E83D05BEAE544E
-:105DA000E862058A87A800E83005E85505BEB754C3
-:105DB000E852058A87A900E82005BEC054E84505D9
-:105DC0008A87AA00E81305BEC954E838058A87AB5C
-:105DD00000E80605BED254E82B058A87AD00E8F935
-:105DE00004BEDB54E81E058A87AE00E8EC04BEE47E
-:105DF00054E811058A87AF00E8DF04BEED54E804DB
-:105E0000058A87B000E8D204E8F704BEF654E8F447
-:105E1000048A87B100E8C204BEFF54E8E7048A8719
-:105E2000B200E8B504BE0855E8DA048A87B300E892
-:105E3000A804BE1155E8CD048A87BB00E89B04E89E
-:105E4000C004BE1A55E8BD048A87BC00E88B04BEB6
-:105E50002355E8B0048A87BE00E87E04BE2C55E8CE
-:105E6000A3048A87BF00E87104E8960407C36006AC
-:105E70001E168BECFF4E16F7461A00027401FBB893
-:105E800000008ED88EC0892E2D7AE8CB0081661A4C
-:105E9000FFFEC6062A7A00E8D800B8005FA32B7A76
-:105EA000E85D00803E2A7A00740A814E1A0001C61D
-:105EB000062A7A00171F0761CF9060061E168BEC2A
-:105EC000F7461A00027401FBB800008ED88EC08914
-:105ED0002E2D7A81661AFFFEC6062A7A00E8920005
-:105EE000B8005FA32B7AE81700803E2A7A00740A74
-:105EF000814E1A0001C6062A7A00171F0761CF904B
-:105F0000B8F000E88CEDFF262B7AC390065356803C
-:105F10003E297A007403E83F00BED779E825028B5A
-:105F2000D8A3277A2E8A07A2297AB0CC2E88075EBA
-:105F30005B07C3C6062A7A00B80A5FA32B7AC39010
-:105F40008B2E2D7AE82B00C3C6062A7A01E80800BA
-:105F5000B80A5FA32B7AC39057803E297A00740F4A
-:105F60008B3E277AA0297A2E8805C606297A005FFB
-:105F7000C390BEB24DE80602BED851E80002FF76DB
-:105F80001458E84702BEDE51E8F301FF760E58E8E8
-:105F90003A02BEE451E8E601FF761258E82D02BE4F
-:105FA000EA51E8D901FF761058E82002BE1452E801
-:105FB000CC01FF760A58E81302BE1A52E8BF01FF6F
-:105FC000760C58E80602BECF51E8B201FF761A58A7
-:105FD000E8F901BEB24DE8A501BEF051E89F01FF0E
-:105FE000761858E8E601BEF651E89201FF760258AD
-:105FF000E8D901BEFC51E88501FF760458E8CC01E0
-:10600000BE0252E87801FF760058E8BF01BE085290
-:10601000E86B01FF760658E8B201BE0E52E85E0159
-:10602000FF760858E8A501BE2052E85101FF761618
-:1060300058E89801BE894DE84401C390BEC94DE8B7
-:106040003C01C33C0074053C017459C3C7060C7A7B
-:10605000CD50C7060E7AF050C706107AE850C70632
-:10606000127AEC50C706147AF450C706167AFB5021
-:10607000C706187A0351C7061A7A0B51C7061C7A4D
-:106080000E51C7061E7A1051C706207A1251C70654
-:10609000227A1651C606247A01C606257A01C6065A
-:1060A000267A03C3C7060C7A1A51C7060E7A4D51D9
-:1060B000C706107A4751C706127A4A51C706147AA2
-:1060C0004F51C706167A5151C706187A5551C7065F
-:1060D0001A7A5651C7061C7A5951C7061E7A5A5168
-:1060E000C706207A5B51C706227A5E51C606247A1B
-:1060F00020C606257A20C606267A02C3A1F879486A
-:106100007414BED779E83C008BF8AC3C3A75078E26
-:10611000C7E830008BF8C3908BC72B06FE798AF056
-:10612000240F8AD002D002D080C20BC0EE0480C6F9
-:1061300003043DC38CC0E89300B03AE8E4008BC789
-:10614000E88900C35133C990AC3C2074FB900AC06D
-:1061500074262C3072223C0976143C11721A2C07DA
-:106160003C0F760A3C2A72102C203C0F770A98C10B
-:10617000E10403C8ACEBD7904E8BC159C390068C99
-:10618000C88EC0E8020007C3268A04460AC0740607
-:10619000E88F00EBF390C3900BC0747A5133D2B9FF
-:1061A000E803F7F18BCAE803008BC159BA6400F623
-:1061B000F2E80C008AC498B20AF6F2E802008AC437
-:1061C000500AF074050430E8580058C386C4E80744
-:1061D0000086C4E80200C390C1C804E80800C1C03A
-:1061E00004E80200C3905350240FBBCA622ED7E8C4
-:1061F0003000585BC39086C4E8070086C4E80200FC
-:10620000C39050B908008AE032C0D1C00430E81110
-:1062100000E2F558C390B030E80700C3B020E801B1
-:1062200000C3568B36D0798884D0774681E6FF014B
-:10623000FF06D4798936D079813ED479FE0175087C
-:1062400056E814005EEBF1905EC3BA0202EC240142
-:106250007404BA0602ECC390803EF67900740960BB
-:10626000B80100E82CEA6190BA0202ECA804742894
-:106270008B36D279833ED47900741D8A84D07746D8
-:1062800081E6FF018936D279FF0ED479BA0602EE93
-:10629000BA0202ECA80475DCA1D479C352BA060292
-:1062A000EE5AC3905250BA0202ECA8047408585A2D
-:1062B000E8E9FFF9C390585AF8C35250BA0202EC09
-:1062C000A80474FB585AE8D3FFC330313233343555
-:1062D0003637383941424344454653508AE080E4DA
-:1062E0000FBBCA62C0E8042ED7E8CEFF8AC42ED7FF
-:1062F000E8C7FF585BC386E0E8DFFF86E0E8DAFF27
-:10630000C390BEB24D502EAC3C007405E8ABFFEB21
-:10631000F558C390C808000056578B7604BF040098
-:10632000C746FC0000C746FA0000C746F8000083D5
-:106330007E0600750E56E8B60E590BC075058BC764
-:10634000E95B018B46FC8946FE0BFF7505B8010031
-:10635000EB0233C05056E8A40D5959B4008946FCED
-:106360008B5EFC83FB087603E92B01D1E32EFFA7AC
-:10637000B264B80300E92601837EFA007414C746AC
-:10638000FA00008A445898508A44599850E8C20F3D
-:106390005959837EF800740AC746F8000056E89BF6
-:1063A0000859837E060075058BC7E9F10083FF0459
-:1063B0007503E9E6008BC7E9E400837EFE00750300
-:1063C000BF0200E9D500837EFE007503BF0100E92E
-:1063D000C9008B5EFE83FB077603E98600D1E32EBE
-:1063E000FFA7A26433FFE97F00BF0400807C580F41
-:1063F0007422837EF800751CFE44586A0856E87EB5
-:106400000C59598A445804805056E8720C5959C79F
-:1064100046FA0100837EF800740AC746F800005669
-:10642000E8190859EB42BF0400807C5800742283AD
-:106430007EF800751CFE4C586A0856E8410C595904
-:106440008A445804805056E8350C5959C746FA0119
-:1064500000837EF800740AC746F8000056E8DC079F
-:1064600059EB05BF0400EB00EB31BF0400EB2CC778
-:1064700046F801006A0856E8050C5959807C58090D
-:106480007D04B00FEB02B00004805056E8F00B59C9
-:1064900059BF0400EB05BF0400EB00E9A5FE5F5EF9
-:1064A000C9C3E4636364636463646364E963266427
-:1064B00051647863BA63C6639664D2636A646A643B
-:1064C0006F647263C808000056578B76048B7E0891
-:1064D0006A0156E8A90B59598A4606C0E0060480AD
-:1064E0005056E89A0B5959C746FE0000897EF8EBD2
-:1064F00003FF46FE8B5EF8FF46F8803F0075F2838F
-:106500007EFE107D25B810002B46FED1F88946FC92
-:10651000C746FA0000EB0B6A2056E8620B5959FF98
-:1065200046FA8B46FA3B46FC7CEDEB0C8BDF478A48
-:10653000075056E8490B5959803D0075EF6A0256DD
-:10654000E83C0B5959EB005F5EC9C3C80400005614
-:10655000578B7E04C746FE0000BE1400E909018B7C
-:106560005EFE83C3042BDF8A87AC0B88445AC64483
-:1065700058088A46FE884459C744060000C6441994
-:1065800000C6441A00C6441B00C6441D0DC6441E66
-:1065900003C6441F00C6442000C6442100C6445B15
-:1065A00000C6445D00C6445E00C6445F00C6446049
-:1065B00000C746FC0000EB0D8B5EFCD1E3C740300A
-:1065C0000000FF46FC837EFC107CEDC746FC00000B
-:1065D000EB0A8B5EFCC6405000FF46FC837EFC0449
-:1065E0007CF0C744540000C7445600008A445A98BF
-:1065F000BAF80023D0B805000BC28946FC9CFA8A81
-:1066000046FCBAFE00EEBA0000EC9D24088846FC69
-:10661000837EFC007502EB4AFF76FEE87A0C59682F
-:10662000350256E8320A59590BC07534683802569B
-:10663000E8250A59590BC0752768420256E8180A1E
-:1066400059590BC0751A684C0256E80B0A59590B78
-:10665000C0750D68560256E8FE0959590BC0740200
-:10666000EB00FF46FE83C662397EFE7D03E9EFFE46
-:10667000EB005F5EC9C3C808000056578B4604BADA
-:106680006200F7EA0514008BF0837E06007405B8FB
-:106690001000EB03B808008944048A460888445C6B
-:1066A00056E85904598BF88BC78944568944548A53
-:1066B000445D88442F0BFF751D68C20F6A0156E8C0
-:1066C00002FE83C406EB006A0156E847FC59590BE9
-:1066D000C075F4BF0100897EFAB90500BBE96A2ED6
-:1066E0008B073B46FA74074343E2F4E9A4032EFF09
-:1066F000670AC744060200C74408F4088B5E04D149
-:10670000E38B87FC0889440A33C08BF8894454E939
-:10671000800356E8BB0559BF01008A445D88446088
-:10672000E96F03837C04087530807C5C0175158AF1
-:10673000445DB400D1E08BD8FFB7E40856E8F70811
-:106740005959EB138A445DB400D1E08BD8FFB7C42C
-:106750000856E8E2085959EB2E807C5C0175158AD1
-:10676000445DB400D1E08BD8FFB7D40856E8C70821
-:106770005959EB138A445DB400D1E08BD8FFB7B40C
-:106780000856E8B20859596A0156E887FB59598BEF
-:10679000D883FB03772AD1E32EFFA7E16ABF01006C
-:1067A0008A445D88445EEB188A445D04FF240788B0
-:1067B000445DEB0C8A445DFEC0240788445DEB0019
-:1067C000E9CF028A445DB400D1E08BD8FFB7FD0267
-:1067D00056E863085959681D0356E85A0859596A1A
-:1067E0000156E82FFB59598BD883FB037736D1E349
-:1067F0002EFFA7D96ABF01008A445D88445FEB245D
-:106800008A445D04FF8A540480C2FF22C288445D2A
-:10681000EB128A445DFEC08A540480C2FF22C28803
-:10682000445DEB00E96B028B5C0683C3FED1E38B16
-:10683000400889048B1CFF77066A0056E885FC83B4
-:10684000C4068B5C064BD1E38B40088944028B5C09
-:1068500002FF77066A0156E86AFC83C4066A01569D
-:10686000E8B1FA59598BD883FB037603E91F02D1AB
-:10687000E32EFFA7D16A8B5C028B47048944028B0D
-:106880005C02803F44750D8B5C028A4701B4003B7B
-:1068900044047DE28B4604D1E08B1C03D88B440278
-:1068A0008947088B5C064BD1E38B4402894008E999
-:1068B000DE018B5C028B47028944028B5C02803FC5
-:1068C00044750D8B5C028A4701B4003B44047DE2B1
-:1068D0008B4604D1E08B1C03D88B44028947088B7C
-:1068E0005C064BD1E38B4402894008E9A201BF0159
-:1068F00000E99C018B5C028A07B4008946F8B90C58
-:1069000000BBA16A2E8B073B46F874074343E2F4B1
-:10691000E977012EFF67188B4604D1E08B5C0203F8
-:10692000D88B47088B5C06FF4406D1E38940088B6F
-:106930001C807F010074128B5C028A47018B1C8AC9
-:106940005701B6008BDA884018E94001FF4C06E990
-:106950003A018B5C028A47018B1C8A5701B6008B77
-:10696000DA884018E925018B5C028A47018B1C8A72
-:106970005701B6008BDA884018FF4C06E90D018BF1
-:106980005C028A47018B1C8A5701B6008BDA3040C3
-:1069900018E9F800B8F0108BF88944548A445F88ED
-:1069A000445DE9E7008A441C983D020074073D03FA
-:1069B000007402EB07C746FE0000EB2B8A441C98CC
-:1069C000D1E08BD8FFB7690256E86B0659596A01C6
-:1069D00056E840F959598946FE837EFE00740683C5
-:1069E0007EFE0375E9EB00837EFE0374628A441C1D
-:1069F00098D1E08BD8FFB76D0256E83A0659595640
-:106A0000E84D97598946FC8B5EFC83EBFE83FB03C4
-:106A10007733D1E32EFFA7996A68AC0256E81706D0
-:106A20005959EB23688F0256E80C065959EB186840
-:106A3000750256E801065959EB0D68C60256E8F68C
-:106A4000055959EB02EB006A0156E8C7F85959BFDE
-:106A50000100EB3868DD0256E8DC0559596A015639
-:106A6000E8B1F85959BF0100EB22B8D0308BF88952
-:106A700044548A446088445DEB12B8E0208BF88966
-:106A800044548A445E88445DEB02EB00EB02EB0069
-:106A9000EB00E941FC5F5EC9C3196A246A2F6A3AB8
-:106AA0006A0000010002000400410042004300446B
-:106AB00000800081008200FF001769546A7A6AA58D
-:106AC00069526994696A6A676952697F6967694C42
-:106AD00069F4687668B268EE68F56700681268F570
-:106AE000679D67A867B4679D6700000100F010E02C
-:106AF00020D0302768F266C36723671267C8040096
-:106B00000056578B76048A4459988946FC6A098B4B
-:106B100046FC05840150E8930859598BF88BC7252A
-:106B200000F03D001075558BC725F0003DF0007555
-:106B30004B8BC725000FC1F8088946FE8B44043BE8
-:106B400046FE7D0533C0E9EF008BC7250F00BA0F65
-:106B5000002BD03B56FE740533C0E9DB00C744026E
-:106B600004098A46FE88445F88445D8B5EFCD1E35D
-:106B7000C787FC080409B8F010E9BC008BC72500E2
-:106B8000F03D002075528BC725F0003DE0007548B0
-:106B90008BC725000FC1F8088946FE837EFE087E5C
-:106BA0000533C0E992008BC7250F00BA0F002BD028
-:106BB0003B56FE740533C0EB7F90C744020C098A34
-:106BC00046FE88445E88445D8B5EFCD1E3C787FC4B
-:106BD000080C09B8E020EB608BC72500F03D0030C1
-:106BE00075528BC725F0003DD00075488BC7250036
-:106BF0000FC1F8088946FE8B44043B46FE7D0433F2
-:106C0000C0EB358BC7250F00BA0F002BD03B56FECB
-:106C1000740433C0EB22C7440214098A46FE884438
-:106C20006088445D8B5EFCD1E3C787FC081409B81B
-:106C3000D030EB0433C0EB005F5EC9C3C806000070
-:106C4000568B76046A0856E8350459598A44580424
-:106C5000805056E8290459598B44543B4456750AD0
-:106C60008A445D3A442F7502EB648B445489445640
-:106C70008B5C028A470188442F8A445DB400C1E0DE
-:106C8000088B54540BD08A445DB400BB0F002BD842
-:106C90000BD38956FE6A108A445998050400990559
-:106CA000400183D2005250E8540883C4068956FC40
-:106CB0008946FA8B46FE0946FA834EFC006A19FFA4
-:106CC00076FCFF76FAE8730783C406E8FE075EC920
-:106CD000C3C81C000056578B5E048A4759988BF036
-:106CE0008B5E048A475DB4008946E6837EE6007DBC
-:106CF0000A8B5E048B4704488946E68B5E048B470B
-:106D0000043B46E67F05C746E600008B5E048A46E4
-:106D1000E688475D8BDED1E38B9F5902C647022090
-:106D20008BDED1E38B9F5902C64703308BDED1E364
-:106D30008B9F6102C64702208BDED1E38B9F6102ED
-:106D4000C64703308B46E68946FA837EFA007418FC
-:106D50008B46FABB0A0033D2F7F380C2308BDED108
-:106D6000E38B9F5902885703BB0A008B46FA33D244
-:106D7000F7F38946FA837EFA0074188B46FABB0A49
-:106D80000033D2F7F380C2308BDED1E38B9F590200
-:106D90008857028B46E68946FA837EFA0074188B80
-:106DA00046FABB0A0033D2F7F380C2308BDED1E360
-:106DB0008B9F6102885703BB0A008B46FA33D2F7D8
-:106DC000F38946FA837EFA0074188B46FABB0A00F0
-:106DD00033D2F7F380C2308BDED1E38B9F61028820
-:106DE00057028B5EE6D1E3FFB712026A00FF76041A
-:106DF000E8D1F683C40668D30F6A01FF7604E8C3BE
-:106E0000F683C406FF76E656E8019359598956F28F
-:106E10008946F0FF76E656E8149359598956EE896B
-:106E200046EC9CFAC45EF0268B078946EAC45EEC09
-:106E3000268B078946E8BA50FFED8946FE9DC74676
-:106E4000E40100E8EEA0BA50FFED8946FC8B46FC59
-:106E50002B46FE3DE8037303E980019CFABA50FF1C
-:106E6000ED8946FC8B46FC2B46FE8946F8C45EF055
-:106E7000268B072B46EA8946F6C45EF0268B0789E7
-:106E800046EAC45EEC268B072B46E88946F4C45ECE
-:106E9000EC268B078946E8BA50FFED8946FE9D81B6
-:106EA0007EF8E803761CFF76F8FF76F6E87601595F
-:106EB000598946F6FF76F8FF76F4E8680159598952
-:106EC00046F4BF0E00EB178BDED1E38B9F5902C651
-:106ED00001208BDED1E38B9F6102C601204783FF37
-:106EE0001176E48BDED1E38B9F5902C6470D308BC0
-:106EF000DED1E38B9F6102C6470D30837EF60977B2
-:106F000005B80D00EB26837EF6637705B80E00EB1F
-:106F10001B817EF6E7037705B80F00EB0F817EF645
-:106F20000F277705B81000EB03B811008BF8EB259D
-:106F30008B46F6BB0A0033D2F7F380C2308BDED12A
-:106F4000E38B9F590288114FBB0A008B46F633D260
-:106F5000F7F38946F6837EF60075D5837EF40977CC
-:106F600005B80D00EB26837EF4637705B80E00EBC1
-:106F70001B817EF4E7037705B80F00EB0F817EF4E9
-:106F80000F277705B81000EB03B811008BF8EB253D
-:106F90008B46F4BB0A0033D2F7F380C2308BDED1CC
-:106FA000E38B9F610288114FBB0A008B46F433D2FA
-:106FB000F7F38946F4837EF40075D58BDED1E3FFC9
-:106FC000B75902FF7604E86E0059598BDED1E3FF12
-:106FD000B76102FF7604E85E0059596A00FF760443
-:106FE000E831F359598BD883FB04771FD1E32EFF87
-:106FF000A71B70EB22C746E40000FF4EE6EB0CC770
-:1070000046E40000FF46E6EB02EB00837EE40074FA
-:1070100003E92AFEE9D4FC5F5EC9C3F36FF56FFF95
-:107020006FF36F0970558BEC8B4604B9E803F7E1F9
-:107030008B4E06F7F15DC3558BEC568B7606EB0E47
-:107040008BDE468A0750FF7604E833005959803CAE
-:107050000075EDEB005E5DC3558BEC568B7606EB51
-:10706000148BDE468A0750FF7604E8450059590B19
-:10707000C07402EB07803C0075E7EB005E5DC3C89F
-:10708000020000568B76048A445A988946FE9CFA80
-:107090008A46FEBAFE00EEBA0200ECA80274069D13
-:1070A000E8919EEBE9BA00008A4606EE9DEB005E91
-:1070B000C9C3C8040000568B76048A445A9889468E
-:1070C000FEE8E6A18946FCE8E0A12B46FC3DB80BB2
-:1070D0007605B80100EB239CFA8A46FEBAFE00EE64
-:1070E000BA0200ECA80274069DE8489EEBD9BA00EB
-:1070F000008A4606EE9D33C0EB005EC9C3C804009B
-:107100000056578B7604837E0600740756E8030109
-:1071100059EB0556E8A200598846FF807EFF0877A4
-:10712000068A46FFE98400807EFF0F7603EB7990A4
-:107130008A46FFB4002D0A008BD883FB047767D101
-:10714000E32EFFA7AF71B000EB6156E86B0059B4B6
-:1071500000250F008946FC56E85E0059B4008BF804
-:1071600056E8550059B400C1E0088BD703D08BFA1C
-:107170008B5EFCD1E3897830EB2E56E83B005988D2
-:10718000445BEB2456E831005988445056E8290006
-:107190005988445156E821005988445256E819004C
-:1071A00059884453EB02EB00E95BFF5F5EC9C346BD
-:1071B00071A6714A717A718471C8040000568B7689
-:1071C000048A445A988946FE9CFA8A46FEBAFE0012
-:1071D000EEBA0200ECA80175069DE8579DEBE9BAEE
-:1071E0000000EC8846FD9D8A46FDEB005EC9C3C8E1
-:1071F000020000568B76048A445A988946FE9CFA0F
-:107200008A46FEBAFE00EEBA0200EC32E424019D8A
-:107210005EC9C3C8060000568B76048A445A988912
-:1072200046FEE885A08946FAE87FA02B46FA3DB8DD
-:107230000B7604B008EB249CFA8A46FEBAFE00EEF8
-:10724000BA0200ECA80175069DE8E89CEBDABA00EA
-:1072500000EC8846FD9D8A46FDEB005EC9C3558B58
-:10726000EC568B56048A4606EE33F6EB035058462E
-:1072700083FE147CF85E5DC3C8020000568B560482
-:10728000EC8846FF33F6EB0350584683FE147CF837
-:107290008A46FFEB005EC9C3C802000056578B76D2
-:1072A00004833EB00B00751FBA8801B000EEBA86A9
-:1072B00001B000EE6A096A00683001E87D0183C40C
-:1072C00006C706B00B01006A098BC605800150E8AD
-:1072D000DA0059598BF88BC7C1E80C250F00894695
-:1072E000FE8BC7C1E808250F008B56FE83F20C3BCE
-:1072F000C275218BC7C1E804250F008B56FE83F2AF
-:10730000063BC2750F8BC7250F008B56FE83F20913
-:107310003BC2740D6A0756E838005959C746FE0744
-:10732000008A46FE0480A233028BC6BA6200F7EAE6
-:107330008A56FE8BD888976C006832028BC6BA6278
-:1073400000F7EA05140050E80EFD5959EB005F5EA6
-:10735000C9C3C8020000568B760683E60F8BC6C1F0
-:10736000E00C8BD683F20CC1E2080BC28BD683F201
-:1073700006C1E2040BC28BD683F2090BC28946FE1A
-:107380006A196A108B46049905400183D200525055
-:10739000E86B0183C4060B46FE83CA005250E89A8C
-:1073A0000083C406E82501EB005EC9C3558BEC568B
-:1073B0005733FF6A01688601E8A3FE5959B1102AC4
-:1073C0004E06D3660433F6EB2E817E0400807204F1
-:1073D000B001EB02B00050688801E881FE59596A9B
-:1073E00003688601E877FE59596A01688601E86DED
-:1073F000FE5959D16604463B76067CCD33F6EB2424
-:10740000D1E76A03688601E854FE59596A01688623
-:1074100001E84AFE5959688801E85CFE599825013F
-:10742000000BF84683FE107CD76A00688601E82DC1
-:10743000FE59598BC7EB005F5E5DC3558BEC565709
-:107440008B7E086A01688601E813FE5959B820004E
-:107450002BC750FF7606FF7604E8A20083C4068996
-:10746000560689460433F6EB47817E060080720C8F
-:107470007506837E04007204B001EB02B000506810
-:107480008801E8D9FD59596A03688601E8CFFD599A
-:10749000596A01688601E8C5FD59596A01FF7606F7
-:1074A000FF7604E8580083C40689560689460446D8
-:1074B0003BF77CB56A00688601E8A2FD59596A006D
-:1074C000688601E898FD59595F5E5DC3558BEC569F
-:1074D0006A01688601E886FD595933F6EB00688831
-:1074E00001E894FD59A80175088BC6463D64007CEF
-:1074F000ED6A00688601E865FD59595E5DC3C80400
-:1075000000008B46048B56068B4E08E306D1E0D173
-:10751000D2E2FA8946FC8956FE8B56FE8B46FCEB7E
-:1075200000C9C300000000000000000000000000CF
-:1075300050726576696F7573204D656E7500426592
-:1075400067696E00000000000000000000000000FD
-:10755000000000000000000000000000000000002B
-:10756000000000000000000000000000000000001B
-:10757000000000000000000000000000000000000B
-:1075800000000000000000000000000000000000FB
-:1075900000000000000000000000000000000000EB
-:1075A00000000000000000000000000000000000DB
-:1075B00000000000000000000000000000000000CB
-:1075C00000000000000000000000000000000000BB
-:1075D00000000000000000000000000000000000AB
-:1075E000000000000000000000000000000000009B
-:1075F000000000000000000000000000000000008B
-:10760000000000000000000000000000000000007A
-:10761000000000000000000000000000000000006A
-:10762000000000000000000000000000000000005A
-:10763000000000000000000000000000000000004A
-:10764000000000000000000000000000000000003A
-:10765000000000000000000000000000000000002A
-:10766000000000000000000000000000000000001A
-:10767000000000000000000000000000000000000A
-:1076800000000000000000000000000000000000FA
-:1076900000000000000000000000000000000000EA
-:1076A00000000000000000000000000000000000DA
-:1076B00000000000000000000000000000000000CA
-:1076C000000000000000000000000000506F727415
-:1076D000203000506F7274203100506F727420326D
-:1076E00000506F7274203300506F72742034005059
-:1076F0006F7274203500506F7274203600506F72B4
-:1077000074203700506F7274203800506F727420EC
-:107710003900506F727420313000506F7274203114
-:107720003100506F727420313200506F727420310A
-:107730003300506F727420313400506F72742031F6
-:1077400035009C01A301AA01B101B801BF01C60126
-:10775000CD01D401DB01E201EA01F201FA010202EA
-:107760000A02080000078100038080809F919591A4
-:107770009F000381848E95848484840003828484A2
-:107780008484958E8400048800B20BC60BDA0BEE5D
-:107790000B020C160C2A0C3E0C520C770C9C0CBEE7
-:1077A0000CE00C020D01802054657374205061734D
-:1077B000736564201F20507265737320800200017E
-:1077C00080204D697373696E67205278204461741C
-:1077D000611F205072657373208002000180204277
-:1077E00061642052782044617461201F20507265CA
-:1077F000737320800200018020586D7472204275DE
-:1078000073791F20507265737320800200018020FD
-:107810006E6F742063757272656E746C791F2020B0
-:10782000696D706C656D656E7465640200240D2F62
-:107830000D3A0D450D500D5B0D660D710D7C0D87DC
-:107840000D920D9D0DA80DB30DBE0DC90D53802CCD
-:107850003254442053862C334454522053822C33C8
-:10786000525453201F53812C3252442053852C32C2
-:1078700043442053832C334354532053842C3344A8
-:1078800053522053872C3252492702000180202076
-:10789000444344202D2070696E2032301F275385C9
-:1078A0002E31818263908081828384858687888956
-:1078B0008A8B8C8D8E8F27020001802020445352AA
-:1078C000202D2070696E2031311F2753842E318185
-:1078D000826390808182838485868788898A8B8C65
-:1078E0008D8E8F27020001802020435453202D20AD
-:1078F00070696E20341F2753832E318182639080FC
-:107900008182838485868788898A8B8C8D8E8F2758
-:107910000200018020205249202D2070696E203203
-:10792000321F2753872E3181826390808182838426
-:1079300085868788898A8B8C8D8E8F2702000180AF
-:107940002020445452202D2070696E20362F381F7D
-:107950002753862E3181826390808182838485863D
-:107960008788898A8B8C8D8E8F270200018020204A
-:10797000525453202D2070696E20351F2753822EBC
-:107980003181826390808182838485868788898A19
-:107990008B8C8D8E8F27020001802020527844200E
-:1079A0002D2070696E20321F2753812E30534D8158
-:1079B000826390808182838485868788898A8B8C84
-:1079C0008D8E8F27020001802020547844202D20A6
-:1079D00070696E20331F2753802E30534D81826390
-:1079E00090808182838485868788898A8B8C8D8E1E
-:1079F0008F27020001802020444344202D207069FD
-:107A00006E20351F2753852E3181826390808182BD
-:107A1000838485868788898A8B8C8D8E8F27020048
-:107A200001802020445352202D2070696E20351F84
-:107A30002753842E3181826390808182838485865E
-:107A40008788898A8B8C8D8E8F2702000180202069
-:107A5000435453202D2070696E20311F2753832EED
-:107A60003181826390808182838485868788898A38
-:107A70008B8C8D8E8F270200018020205249202D73
-:107A800020286E2E632E291F2753872E3181826373
-:107A900090808182838485868788898A8B8C8D8E6D
-:107AA0008F27020001802020445452202D2070692D
-:107AB0006E20321F2753862E31818263908081820F
-:107AC000838485868788898A8B8C8D8E8F27020098
-:107AD00001802020525453202D2070696E20371FC2
-:107AE0002753822E318182639080818283848586B0
-:107AF0008788898A8B8C8D8E8F27020001802020B9
-:107B0000527844202D2070696E20361F2753812E15
-:107B100030534D81826390808182838485868788FB
-:107B2000898A8B8C8D8E8F270200018020205478CB
-:107B300044202D2070696E20331F2753802E305330
-:107B40004D81826390808182838485868788898A3B
-:107B50008B8C8D8E8F27020001802020444344208F
-:107B60002D2070696E20351F202020202753852E60
-:107B700031818263888081828384858687270200A1
-:107B800001802020445352202D2070696E20351F23
-:107B9000202020202753842E318182638880818297
-:107BA0008384858687270200018020204354532048
-:107BB0002D2070696E20311F202020202753832E16
-:107BC0003181826388808182838485868727020051
-:107BD000018020205249202D20286E2E632E291F3F
-:107BE000202020202753872E318182638880818244
-:107BF00083848586872702000180202044545220F8
-:107C00002D2070696E20321F202020202753862EC1
-:107C10003181826388808182838485868727020000
-:107C200001802020525453202D2070696E20371F70
-:107C3000202020202753822E3181826388808182F8
-:107C40008384858687270200018020205278442083
-:107C50002D2070696E20361F202020202753812E72
-:107C600030534D8182638880818283848586872713
-:107C7000020001802020547844202D2070696E205D
-:107C8000331F202020202753802E30534D818263C4
-:107C90008880818283848586872702000180202056
-:107CA000444344202D2070696E2032301F20202054
-:107CB000202753852E318182638880818283848549
-:107CC000868727020001802020445352202D2070F7
-:107CD000696E2031311F202020202753842E3181CE
-:107CE0008263888081828384858687270200018061
-:107CF0002020435453202D2070696E20341F2020F3
-:107D000020202753832E318182638880818283845F
-:107D1000858687270200018020205249202D20706F
-:107D2000696E2032321F202020202753872E318178
-:107D30008263888081828384858687270200018010
-:107D40002020445452202D2070696E20362F381F79
-:107D5000202020202753862E3181826388808182D3
-:107D60008384858687270200018020205254532077
-:107D70002D2070696E20351F202020202753822E51
-:107D8000318182638880818283848586872702008F
-:107D900001802020527844202D2070696E20321FEF
-:107DA000202020202753812E30534D8182638880EC
-:107DB0008182838485868727020001802020547871
-:107DC00044202D2070696E20331F2020202027534F
-:107DD000802E30534D8182638880818283848586A2
-:107DE0008727020068049604B6033C040E04890346
-:107DF0005C03E20360088A08BE0738080E0895078E
-:107E00006C07E6071C057405FA05C404F004CC05EC
-:107E1000A00548057806C806420728065006180738
-:107E2000F006A0060000F408F408D40D04090409C3
-:107E30000409040942000C091C09E50D020014099B
-:107E40000409F40D43001C090C09050E0004040983
-:107E50001409120E2C092C092C092C0900003C09CC
-:107E60006C091E0E740974097409740900014C0927
-:107E70002C092D0E740974097409740900025C0937
-:107E80003C093D0E740974097409740900036C09F6
-:107E90004C094D0E7409740974097409FF002C090A
-:107EA0005C09000000058409EC095E0EF409F40980
-:107EB000F409F409000694097409680EAC0AAC0AC6
-:107EC000AC0AAC0A0007A4098409720EBC0ABC0AF9
-:107ED000BC0ABC0A0008B40994097C0ED40AD40A6E
-:107EE000D40AD40A000BC409A409830EFC0AFC0AB4
-:107EF000FC0AFC0A000CD409B409900E140B140BF4
-:107F0000140B140B0002E409C409A00E2C0B2C0B5B
-:107F10002C0B2C0B0400EC09D4090E00FF00740993
-:107F2000E40900008201FC09A40AAC0E8202040AE2
-:107F3000F409AF0E82030C0AFC09B20E8204140A83
-:107F4000040AB60E82051C0A0C0ABC0E8206240A1C
-:107F5000140AC00E82072C0A1C0AC40E8208340AB6
-:107F6000240AC80E82093C0A2C0ACC0E820A440A52
-:107F7000340AD10E82104C0A3C0AD60E820B540AE7
-:107F8000440ADB0E82115C0A4C0AE00E820C640A81
-:107F9000540AE50E82126C0A5C0AEA0E820D740A1B
-:107FA000640AEF0E820E7C0A6C0AF40E820F840AB9
-:107FB000740AFB0E82138C0A7C0A020F8214940A44
-:107FC000840A090F82159C0A8C0A100F8216A40AD3
-:107FD000940A170F8217F4099C0A1E0F8202B40A32
-:107FE000B40A260F8203AC0AAC0A2D0F8200C40A21
-:107FF000CC0A340F8201CC0ABC0A3F0F8202BC0AB1
-:10800000C40A4D0F8200DC0AF40A590F8201E40A07
-:10801000D40A630F8202EC0ADC0A6E0F8203F40AB0
-:10802000E40A7A0F8204D40AEC0A870F8200040B58
-:108030000C0B930F82010C0BFC0A9B0F8202FC0AB3
-:10804000040BA70F82001C0B240BB00F8201240B22
-:10805000140BB50F8202140B1C0BBE0F4400340B23
-:10806000A40B9C0144013C0B2C0BA3014402440BC8
-:10807000340BAA0144034C0B3C0BB1014404540BD8
-:10808000440BB80144055C0B4C0BBF014406640B68
-:10809000540BC60144076C0B5C0BCD014408740BF8
-:1080A000640BD40144097C0B6C0BDB01440A840B88
-:1080B000740BE201440B8C0B7C0BEA01440C940B17
-:1080C000840BF201440D9C0B8C0BFA01440EA40BA3
-:1080D000940B0202440F2C0B9C0B0A02171F0F2F4C
-:1080E0000000018078783A20747820637073202A29
-:1080F0002A2A2A2A0200018078783A20747820639C
-:108100007073202A2A2A2A2A0200018078783A20CD
-:10811000747820637073202A2A2A2A2A0200018098
-:1081200078783A20747820637073202A2A2A2A2AC1
-:10813000020001C078783A20726320637073202AAD
-:108140002A2A2A2A020001C078783A207263206322
-:108150007073202A2A2A2A2A020001C078783A203D
-:10816000726320637073202A2A2A2A2A020001C01F
-:1081700078783A20726320637073202A2A2A2A2A88
-:1081800002000180496E7374616C6C204C6F6F70DB
-:108190006261636B1F5072657373208020746F205F
-:1081A000737461727402000180204361626C652007
-:1081B000746F2052656D6F74651F50726573732004
-:1081C0008020746F20737461727402000180204CEF
-:1081D0006F63616C204C6F6F706261636B201F2056
-:1081E0002052756E6E696E67202E2E2E0200018061
-:1081F00052656D6F7465204C6F6F706261636B20A8
-:108200001F202052756E6E696E67202E2E2E020082
-:10821000018020496E74726E6C204C6F6F706261C9
-:10822000636B1F202052756E6E696E67202E2E2E96
-:10823000020001805472616E736D69742050617424
-:108240007465726E1F202052756E6E696E67202EE7
-:108250002E2E020001802020303A2027438000018A
-:10826000802020313A202743810001802020323AAB
-:10827000202743820001802020333A2027438300B7
-:1082800001802020343A20274384000180202035BB
-:108290003A202743850001802020363A2027438654
-:1082A0000001802020373A202743870001802020CA
-:1082B000383A202743880001802020393A2027437C
-:1082C000890001802031303A2027438A0001802034
-:1082D00031313A2027438B0001802031323A202768
-:1082E000438C0001802031333A2027438D000180E8
-:1082F0002031343A2027438E0001802031353A2046
-:1083000027438F002A2A204D61696E20204D656E1B
-:1083100075202A2A004D6F6E69746F72206120509B
-:108320006F7274004D6F6E69746F722061205369B3
-:10833000676E616C00457374696D617465204350AC
-:108340005300446961676E6F7374696373004C6FA7
-:1083500063616C204C6F6F706261636B0052656D7E
-:108360006F7465204C6F6F706261636B00496E744F
-:10837000726E6C204C6F6F706261636B005472613F
-:108380006E736D6974205061747465726E00426121
-:10839000756420526174650044617461204269749F
-:1083A000730053746F702042697473005061726976
-:1083B00074790044617461205061747465726E0058
-:1083C000547820466C6F7720436F6E74726F6C0028
-:1083D000506F7274204E756D6265720035300037D3
-:1083E0003500313130003133342E35003135300035
-:1083F00032303000333030003630300031323030FF
-:10840000003138303000323030300032343030001B
-:1084100033363030003438303000373230300039C5
-:108420003630300031392C3230300033382C343093
-:10843000300035362C3030300035372C36303000B7
-:1084400036342C3030300037362C38303000313173
-:10845000352C323030003720626974730038206266
-:1084600069747300312073746F7020626974003115
-:108470002E352073746F702062697473003220731C
-:10848000746F702062697473006E6F20706172691E
-:108490007479006F64642070617269747900657624
-:1084A000656E207061726974790073706163652014
-:1084B000706172697479006D61726B2070617269AC
-:1084C000747900436F6C756D6E7300426172626502
-:1084D0007220506F6C650055555555552E2E2E0047
-:1084E0004E6F6E6500586F6E2F586F66660043546E
-:1084F00053005072657373208020666F72206D6523
-:108500006E750028636F756E74696E672E2E2E2946
-:108510000000654E64204F6620436F4465000000F4
-:10852000000000000000000000000000000000004B
-:10853000000000000000000000000000000000003B
-:10854000000000000000000000000000000000002B
-:10855000000000000000000000000000000000001B
-:10856000000000000000000000000000000000000B
-:1085700000000000000000000000000000000000FB
-:1085800000000000000000000000000000000000EB
-:1085900000000000000000000000000000000000DB
-:1085A00000000000000000000000000000000000CB
-:1085B00000000000000000000000000000000000BB
-:1085C00000000000000000000000000000000000AB
-:1085D000000000000000000000000000000000009B
-:1085E000000000000000000000000000000000008B
-:1085F000000000000000000000000000000000007B
-:00000001FF
-/*  Intelliport II loadware */
-/* -31232 bytes read from ff.lod */
diff --git a/fs/bio.c b/fs/bio.c
index 5eaa70c..71072ab 100644
--- a/fs/bio.c
+++ b/fs/bio.c
@@ -73,7 +73,7 @@
 {
 	unsigned int sz = sizeof(struct bio) + extra_size;
 	struct kmem_cache *slab = NULL;
-	struct bio_slab *bslab;
+	struct bio_slab *bslab, *new_bio_slabs;
 	unsigned int i, entry = -1;
 
 	mutex_lock(&bio_slab_lock);
@@ -97,11 +97,12 @@
 
 	if (bio_slab_nr == bio_slab_max && entry == -1) {
 		bio_slab_max <<= 1;
-		bio_slabs = krealloc(bio_slabs,
-				     bio_slab_max * sizeof(struct bio_slab),
-				     GFP_KERNEL);
-		if (!bio_slabs)
+		new_bio_slabs = krealloc(bio_slabs,
+					 bio_slab_max * sizeof(struct bio_slab),
+					 GFP_KERNEL);
+		if (!new_bio_slabs)
 			goto out_unlock;
+		bio_slabs = new_bio_slabs;
 	}
 	if (entry == -1)
 		entry = bio_slab_nr++;
diff --git a/fs/block_dev.c b/fs/block_dev.c
index 1e51919..38e721b 100644
--- a/fs/block_dev.c
+++ b/fs/block_dev.c
@@ -1578,10 +1578,12 @@
 			 unsigned long nr_segs, loff_t pos)
 {
 	struct file *file = iocb->ki_filp;
+	struct blk_plug plug;
 	ssize_t ret;
 
 	BUG_ON(iocb->ki_pos != pos);
 
+	blk_start_plug(&plug);
 	ret = __generic_file_aio_write(iocb, iov, nr_segs, &iocb->ki_pos);
 	if (ret > 0 || ret == -EIOCBQUEUED) {
 		ssize_t err;
@@ -1590,6 +1592,7 @@
 		if (err < 0 && ret > 0)
 			ret = err;
 	}
+	blk_finish_plug(&plug);
 	return ret;
 }
 EXPORT_SYMBOL_GPL(blkdev_aio_write);
diff --git a/fs/btrfs/backref.c b/fs/btrfs/backref.c
index a256f3b..ff6475f 100644
--- a/fs/btrfs/backref.c
+++ b/fs/btrfs/backref.c
@@ -1438,10 +1438,10 @@
 	ret = extent_from_logical(fs_info, logical, path,
 					&found_key);
 	btrfs_release_path(path);
-	if (ret & BTRFS_EXTENT_FLAG_TREE_BLOCK)
-		ret = -EINVAL;
 	if (ret < 0)
 		return ret;
+	if (ret & BTRFS_EXTENT_FLAG_TREE_BLOCK)
+		return -EINVAL;
 
 	extent_item_pos = logical - found_key.objectid;
 	ret = iterate_extent_inodes(fs_info, found_key.objectid,
diff --git a/fs/btrfs/compression.c b/fs/btrfs/compression.c
index 86eff48..43d1c5a 100644
--- a/fs/btrfs/compression.c
+++ b/fs/btrfs/compression.c
@@ -818,6 +818,7 @@
 	btrfs_compress_op[idx]->free_workspace(workspace);
 	atomic_dec(alloc_workspace);
 wake:
+	smp_mb();
 	if (waitqueue_active(workspace_wait))
 		wake_up(workspace_wait);
 }
diff --git a/fs/btrfs/ctree.c b/fs/btrfs/ctree.c
index 9d7621f..6d183f6 100644
--- a/fs/btrfs/ctree.c
+++ b/fs/btrfs/ctree.c
@@ -421,12 +421,6 @@
 	spin_unlock(&fs_info->tree_mod_seq_lock);
 
 	/*
-	 * we removed the lowest blocker from the blocker list, so there may be
-	 * more processible delayed refs.
-	 */
-	wake_up(&fs_info->tree_mod_seq_wait);
-
-	/*
 	 * anything that's lower than the lowest existing (read: blocked)
 	 * sequence number can be removed from the tree.
 	 */
@@ -631,6 +625,9 @@
 	u32 nritems;
 	int ret;
 
+	if (btrfs_header_level(eb) == 0)
+		return;
+
 	nritems = btrfs_header_nritems(eb);
 	for (i = nritems - 1; i >= 0; i--) {
 		ret = tree_mod_log_insert_key_locked(fs_info, eb, i,
diff --git a/fs/btrfs/ctree.h b/fs/btrfs/ctree.h
index 4bab807..0d195b5 100644
--- a/fs/btrfs/ctree.h
+++ b/fs/btrfs/ctree.h
@@ -1252,7 +1252,6 @@
 	atomic_t tree_mod_seq;
 	struct list_head tree_mod_seq_list;
 	struct seq_list tree_mod_seq_elem;
-	wait_queue_head_t tree_mod_seq_wait;
 
 	/* this protects tree_mod_log */
 	rwlock_t tree_mod_log_lock;
@@ -3192,7 +3191,7 @@
 int btrfs_lookup_bio_sums(struct btrfs_root *root, struct inode *inode,
 			  struct bio *bio, u32 *dst);
 int btrfs_lookup_bio_sums_dio(struct btrfs_root *root, struct inode *inode,
-			      struct bio *bio, u64 logical_offset, u32 *dst);
+			      struct bio *bio, u64 logical_offset);
 int btrfs_insert_file_extent(struct btrfs_trans_handle *trans,
 			     struct btrfs_root *root,
 			     u64 objectid, u64 pos,
diff --git a/fs/btrfs/delayed-inode.c b/fs/btrfs/delayed-inode.c
index 335605c..07d5eeb 100644
--- a/fs/btrfs/delayed-inode.c
+++ b/fs/btrfs/delayed-inode.c
@@ -512,8 +512,8 @@
 
 	rb_erase(&delayed_item->rb_node, root);
 	delayed_item->delayed_node->count--;
-	atomic_dec(&delayed_root->items);
-	if (atomic_read(&delayed_root->items) < BTRFS_DELAYED_BACKGROUND &&
+	if (atomic_dec_return(&delayed_root->items) <
+	    BTRFS_DELAYED_BACKGROUND &&
 	    waitqueue_active(&delayed_root->wait))
 		wake_up(&delayed_root->wait);
 }
@@ -1028,9 +1028,10 @@
 		btrfs_release_delayed_item(prev);
 		ret = 0;
 		btrfs_release_path(path);
-		if (curr)
+		if (curr) {
+			mutex_unlock(&node->mutex);
 			goto do_again;
-		else
+		} else
 			goto delete_fail;
 	}
 
@@ -1055,8 +1056,7 @@
 		delayed_node->count--;
 
 		delayed_root = delayed_node->root->fs_info->delayed_root;
-		atomic_dec(&delayed_root->items);
-		if (atomic_read(&delayed_root->items) <
+		if (atomic_dec_return(&delayed_root->items) <
 		    BTRFS_DELAYED_BACKGROUND &&
 		    waitqueue_active(&delayed_root->wait))
 			wake_up(&delayed_root->wait);
diff --git a/fs/btrfs/delayed-ref.c b/fs/btrfs/delayed-ref.c
index da7419e..ae94117 100644
--- a/fs/btrfs/delayed-ref.c
+++ b/fs/btrfs/delayed-ref.c
@@ -38,17 +38,14 @@
 static int comp_tree_refs(struct btrfs_delayed_tree_ref *ref2,
 			  struct btrfs_delayed_tree_ref *ref1)
 {
-	if (ref1->node.type == BTRFS_TREE_BLOCK_REF_KEY) {
-		if (ref1->root < ref2->root)
-			return -1;
-		if (ref1->root > ref2->root)
-			return 1;
-	} else {
-		if (ref1->parent < ref2->parent)
-			return -1;
-		if (ref1->parent > ref2->parent)
-			return 1;
-	}
+	if (ref1->root < ref2->root)
+		return -1;
+	if (ref1->root > ref2->root)
+		return 1;
+	if (ref1->parent < ref2->parent)
+		return -1;
+	if (ref1->parent > ref2->parent)
+		return 1;
 	return 0;
 }
 
@@ -85,7 +82,8 @@
  * type of the delayed backrefs and content of delayed backrefs.
  */
 static int comp_entry(struct btrfs_delayed_ref_node *ref2,
-		      struct btrfs_delayed_ref_node *ref1)
+		      struct btrfs_delayed_ref_node *ref1,
+		      bool compare_seq)
 {
 	if (ref1->bytenr < ref2->bytenr)
 		return -1;
@@ -102,10 +100,12 @@
 	if (ref1->type > ref2->type)
 		return 1;
 	/* merging of sequenced refs is not allowed */
-	if (ref1->seq < ref2->seq)
-		return -1;
-	if (ref1->seq > ref2->seq)
-		return 1;
+	if (compare_seq) {
+		if (ref1->seq < ref2->seq)
+			return -1;
+		if (ref1->seq > ref2->seq)
+			return 1;
+	}
 	if (ref1->type == BTRFS_TREE_BLOCK_REF_KEY ||
 	    ref1->type == BTRFS_SHARED_BLOCK_REF_KEY) {
 		return comp_tree_refs(btrfs_delayed_node_to_tree_ref(ref2),
@@ -139,7 +139,7 @@
 		entry = rb_entry(parent_node, struct btrfs_delayed_ref_node,
 				 rb_node);
 
-		cmp = comp_entry(entry, ins);
+		cmp = comp_entry(entry, ins, 1);
 		if (cmp < 0)
 			p = &(*p)->rb_left;
 		else if (cmp > 0)
@@ -233,6 +233,114 @@
 	return 0;
 }
 
+static void inline drop_delayed_ref(struct btrfs_trans_handle *trans,
+				    struct btrfs_delayed_ref_root *delayed_refs,
+				    struct btrfs_delayed_ref_node *ref)
+{
+	rb_erase(&ref->rb_node, &delayed_refs->root);
+	ref->in_tree = 0;
+	btrfs_put_delayed_ref(ref);
+	delayed_refs->num_entries--;
+	if (trans->delayed_ref_updates)
+		trans->delayed_ref_updates--;
+}
+
+static int merge_ref(struct btrfs_trans_handle *trans,
+		     struct btrfs_delayed_ref_root *delayed_refs,
+		     struct btrfs_delayed_ref_node *ref, u64 seq)
+{
+	struct rb_node *node;
+	int merged = 0;
+	int mod = 0;
+	int done = 0;
+
+	node = rb_prev(&ref->rb_node);
+	while (node) {
+		struct btrfs_delayed_ref_node *next;
+
+		next = rb_entry(node, struct btrfs_delayed_ref_node, rb_node);
+		node = rb_prev(node);
+		if (next->bytenr != ref->bytenr)
+			break;
+		if (seq && next->seq >= seq)
+			break;
+		if (comp_entry(ref, next, 0))
+			continue;
+
+		if (ref->action == next->action) {
+			mod = next->ref_mod;
+		} else {
+			if (ref->ref_mod < next->ref_mod) {
+				struct btrfs_delayed_ref_node *tmp;
+
+				tmp = ref;
+				ref = next;
+				next = tmp;
+				done = 1;
+			}
+			mod = -next->ref_mod;
+		}
+
+		merged++;
+		drop_delayed_ref(trans, delayed_refs, next);
+		ref->ref_mod += mod;
+		if (ref->ref_mod == 0) {
+			drop_delayed_ref(trans, delayed_refs, ref);
+			break;
+		} else {
+			/*
+			 * You can't have multiples of the same ref on a tree
+			 * block.
+			 */
+			WARN_ON(ref->type == BTRFS_TREE_BLOCK_REF_KEY ||
+				ref->type == BTRFS_SHARED_BLOCK_REF_KEY);
+		}
+
+		if (done)
+			break;
+		node = rb_prev(&ref->rb_node);
+	}
+
+	return merged;
+}
+
+void btrfs_merge_delayed_refs(struct btrfs_trans_handle *trans,
+			      struct btrfs_fs_info *fs_info,
+			      struct btrfs_delayed_ref_root *delayed_refs,
+			      struct btrfs_delayed_ref_head *head)
+{
+	struct rb_node *node;
+	u64 seq = 0;
+
+	spin_lock(&fs_info->tree_mod_seq_lock);
+	if (!list_empty(&fs_info->tree_mod_seq_list)) {
+		struct seq_list *elem;
+
+		elem = list_first_entry(&fs_info->tree_mod_seq_list,
+					struct seq_list, list);
+		seq = elem->seq;
+	}
+	spin_unlock(&fs_info->tree_mod_seq_lock);
+
+	node = rb_prev(&head->node.rb_node);
+	while (node) {
+		struct btrfs_delayed_ref_node *ref;
+
+		ref = rb_entry(node, struct btrfs_delayed_ref_node,
+			       rb_node);
+		if (ref->bytenr != head->node.bytenr)
+			break;
+
+		/* We can't merge refs that are outside of our seq count */
+		if (seq && ref->seq >= seq)
+			break;
+		if (merge_ref(trans, delayed_refs, ref, seq))
+			node = rb_prev(&head->node.rb_node);
+		else
+			node = rb_prev(node);
+	}
+}
+
 int btrfs_check_delayed_seq(struct btrfs_fs_info *fs_info,
 			    struct btrfs_delayed_ref_root *delayed_refs,
 			    u64 seq)
@@ -336,18 +444,11 @@
 		 * every changing the extent allocation tree.
 		 */
 		existing->ref_mod--;
-		if (existing->ref_mod == 0) {
-			rb_erase(&existing->rb_node,
-				 &delayed_refs->root);
-			existing->in_tree = 0;
-			btrfs_put_delayed_ref(existing);
-			delayed_refs->num_entries--;
-			if (trans->delayed_ref_updates)
-				trans->delayed_ref_updates--;
-		} else {
+		if (existing->ref_mod == 0)
+			drop_delayed_ref(trans, delayed_refs, existing);
+		else
 			WARN_ON(existing->type == BTRFS_TREE_BLOCK_REF_KEY ||
 				existing->type == BTRFS_SHARED_BLOCK_REF_KEY);
-		}
 	} else {
 		WARN_ON(existing->type == BTRFS_TREE_BLOCK_REF_KEY ||
 			existing->type == BTRFS_SHARED_BLOCK_REF_KEY);
@@ -662,9 +763,6 @@
 	add_delayed_tree_ref(fs_info, trans, &ref->node, bytenr,
 				   num_bytes, parent, ref_root, level, action,
 				   for_cow);
-	if (!need_ref_seq(for_cow, ref_root) &&
-	    waitqueue_active(&fs_info->tree_mod_seq_wait))
-		wake_up(&fs_info->tree_mod_seq_wait);
 	spin_unlock(&delayed_refs->lock);
 	if (need_ref_seq(for_cow, ref_root))
 		btrfs_qgroup_record_ref(trans, &ref->node, extent_op);
@@ -713,9 +811,6 @@
 	add_delayed_data_ref(fs_info, trans, &ref->node, bytenr,
 				   num_bytes, parent, ref_root, owner, offset,
 				   action, for_cow);
-	if (!need_ref_seq(for_cow, ref_root) &&
-	    waitqueue_active(&fs_info->tree_mod_seq_wait))
-		wake_up(&fs_info->tree_mod_seq_wait);
 	spin_unlock(&delayed_refs->lock);
 	if (need_ref_seq(for_cow, ref_root))
 		btrfs_qgroup_record_ref(trans, &ref->node, extent_op);
@@ -744,8 +839,6 @@
 				   num_bytes, BTRFS_UPDATE_DELAYED_HEAD,
 				   extent_op->is_data);
 
-	if (waitqueue_active(&fs_info->tree_mod_seq_wait))
-		wake_up(&fs_info->tree_mod_seq_wait);
 	spin_unlock(&delayed_refs->lock);
 	return 0;
 }
diff --git a/fs/btrfs/delayed-ref.h b/fs/btrfs/delayed-ref.h
index 0d7c90c..ab53005 100644
--- a/fs/btrfs/delayed-ref.h
+++ b/fs/btrfs/delayed-ref.h
@@ -167,6 +167,10 @@
 				struct btrfs_trans_handle *trans,
 				u64 bytenr, u64 num_bytes,
 				struct btrfs_delayed_extent_op *extent_op);
+void btrfs_merge_delayed_refs(struct btrfs_trans_handle *trans,
+			      struct btrfs_fs_info *fs_info,
+			      struct btrfs_delayed_ref_root *delayed_refs,
+			      struct btrfs_delayed_ref_head *head);
 
 struct btrfs_delayed_ref_head *
 btrfs_find_delayed_ref_head(struct btrfs_trans_handle *trans, u64 bytenr);
diff --git a/fs/btrfs/disk-io.c b/fs/btrfs/disk-io.c
index 62e0caf..22e98e0 100644
--- a/fs/btrfs/disk-io.c
+++ b/fs/btrfs/disk-io.c
@@ -377,9 +377,13 @@
 		ret = read_extent_buffer_pages(io_tree, eb, start,
 					       WAIT_COMPLETE,
 					       btree_get_extent, mirror_num);
-		if (!ret && !verify_parent_transid(io_tree, eb,
+		if (!ret) {
+			if (!verify_parent_transid(io_tree, eb,
 						   parent_transid, 0))
-			break;
+				break;
+			else
+				ret = -EIO;
+		}
 
 		/*
 		 * This buffer's crc is fine, but its contents are corrupted, so
@@ -754,9 +758,7 @@
 	limit = btrfs_async_submit_limit(fs_info);
 	limit = limit * 2 / 3;
 
-	atomic_dec(&fs_info->nr_async_submits);
-
-	if (atomic_read(&fs_info->nr_async_submits) < limit &&
+	if (atomic_dec_return(&fs_info->nr_async_submits) < limit &&
 	    waitqueue_active(&fs_info->async_submit_wait))
 		wake_up(&fs_info->async_submit_wait);
 
@@ -2032,8 +2034,6 @@
 	fs_info->free_chunk_space = 0;
 	fs_info->tree_mod_log = RB_ROOT;
 
-	init_waitqueue_head(&fs_info->tree_mod_seq_wait);
-
 	/* readahead state */
 	INIT_RADIX_TREE(&fs_info->reada_tree, GFP_NOFS & ~__GFP_WAIT);
 	spin_lock_init(&fs_info->reada_lock);
@@ -2528,8 +2528,7 @@
 		goto fail_trans_kthread;
 
 	/* do not make disk changes in broken FS */
-	if (btrfs_super_log_root(disk_super) != 0 &&
-	    !(fs_info->fs_state & BTRFS_SUPER_FLAG_ERROR)) {
+	if (btrfs_super_log_root(disk_super) != 0) {
 		u64 bytenr = btrfs_super_log_root(disk_super);
 
 		if (fs_devices->rw_devices == 0) {
@@ -3189,30 +3188,14 @@
 	/* clear out the rbtree of defraggable inodes */
 	btrfs_run_defrag_inodes(fs_info);
 
-	/*
-	 * Here come 2 situations when btrfs is broken to flip readonly:
-	 *
-	 * 1. when btrfs flips readonly somewhere else before
-	 * btrfs_commit_super, sb->s_flags has MS_RDONLY flag,
-	 * and btrfs will skip to write sb directly to keep
-	 * ERROR state on disk.
-	 *
-	 * 2. when btrfs flips readonly just in btrfs_commit_super,
-	 * and in such case, btrfs cannot write sb via btrfs_commit_super,
-	 * and since fs_state has been set BTRFS_SUPER_FLAG_ERROR flag,
-	 * btrfs will cleanup all FS resources first and write sb then.
-	 */
 	if (!(fs_info->sb->s_flags & MS_RDONLY)) {
 		ret = btrfs_commit_super(root);
 		if (ret)
 			printk(KERN_ERR "btrfs: commit super ret %d\n", ret);
 	}
 
-	if (fs_info->fs_state & BTRFS_SUPER_FLAG_ERROR) {
-		ret = btrfs_error_commit_super(root);
-		if (ret)
-			printk(KERN_ERR "btrfs: commit super ret %d\n", ret);
-	}
+	if (fs_info->fs_state & BTRFS_SUPER_FLAG_ERROR)
+		btrfs_error_commit_super(root);
 
 	btrfs_put_block_group_cache(fs_info);
 
@@ -3434,18 +3417,11 @@
 	if (read_only)
 		return 0;
 
-	if (fs_info->fs_state & BTRFS_SUPER_FLAG_ERROR) {
-		printk(KERN_WARNING "warning: mount fs with errors, "
-		       "running btrfsck is recommended\n");
-	}
-
 	return 0;
 }
 
-int btrfs_error_commit_super(struct btrfs_root *root)
+void btrfs_error_commit_super(struct btrfs_root *root)
 {
-	int ret;
-
 	mutex_lock(&root->fs_info->cleaner_mutex);
 	btrfs_run_delayed_iputs(root);
 	mutex_unlock(&root->fs_info->cleaner_mutex);
@@ -3455,10 +3431,6 @@
 
 	/* cleanup FS via transaction */
 	btrfs_cleanup_transaction(root);
-
-	ret = write_ctree_super(NULL, root, 0);
-
-	return ret;
 }
 
 static void btrfs_destroy_ordered_operations(struct btrfs_root *root)
@@ -3782,14 +3754,17 @@
 		/* FIXME: cleanup wait for commit */
 		t->in_commit = 1;
 		t->blocked = 1;
+		smp_mb();
 		if (waitqueue_active(&root->fs_info->transaction_blocked_wait))
 			wake_up(&root->fs_info->transaction_blocked_wait);
 
 		t->blocked = 0;
+		smp_mb();
 		if (waitqueue_active(&root->fs_info->transaction_wait))
 			wake_up(&root->fs_info->transaction_wait);
 
 		t->commit_done = 1;
+		smp_mb();
 		if (waitqueue_active(&t->commit_wait))
 			wake_up(&t->commit_wait);
 
diff --git a/fs/btrfs/disk-io.h b/fs/btrfs/disk-io.h
index 95e147e..c5b00a7 100644
--- a/fs/btrfs/disk-io.h
+++ b/fs/btrfs/disk-io.h
@@ -54,7 +54,7 @@
 		      struct btrfs_root *root, int max_mirrors);
 struct buffer_head *btrfs_read_dev_super(struct block_device *bdev);
 int btrfs_commit_super(struct btrfs_root *root);
-int btrfs_error_commit_super(struct btrfs_root *root);
+void btrfs_error_commit_super(struct btrfs_root *root);
 struct extent_buffer *btrfs_find_tree_block(struct btrfs_root *root,
 					    u64 bytenr, u32 blocksize);
 struct btrfs_root *btrfs_read_fs_root_no_radix(struct btrfs_root *tree_root,
diff --git a/fs/btrfs/extent-tree.c b/fs/btrfs/extent-tree.c
index 4e1b153..ba58024 100644
--- a/fs/btrfs/extent-tree.c
+++ b/fs/btrfs/extent-tree.c
@@ -2252,6 +2252,16 @@
 		}
 
 		/*
+		 * We need to try and merge add/drops of the same ref since we
+		 * can run into issues with relocate dropping the implicit ref
+		 * and then it being added back again before the drop can
+		 * finish.  If we merged anything we need to re-loop so we can
+		 * get a good ref.
+		 */
+		btrfs_merge_delayed_refs(trans, fs_info, delayed_refs,
+					 locked_ref);
+
+		/*
 		 * locked_ref is the head node, so we have to go one
 		 * node back for any delayed ref updates
 		 */
@@ -2318,12 +2328,23 @@
 		ref->in_tree = 0;
 		rb_erase(&ref->rb_node, &delayed_refs->root);
 		delayed_refs->num_entries--;
-		/*
-		 * we modified num_entries, but as we're currently running
-		 * delayed refs, skip
-		 *     wake_up(&delayed_refs->seq_wait);
-		 * here.
-		 */
+		if (locked_ref) {
+			/*
+			 * when we play the delayed ref, also correct the
+			 * ref_mod on head
+			 */
+			switch (ref->action) {
+			case BTRFS_ADD_DELAYED_REF:
+			case BTRFS_ADD_DELAYED_EXTENT:
+				locked_ref->node.ref_mod -= ref->ref_mod;
+				break;
+			case BTRFS_DROP_DELAYED_REF:
+				locked_ref->node.ref_mod += ref->ref_mod;
+				break;
+			default:
+				WARN_ON(1);
+			}
+		}
 		spin_unlock(&delayed_refs->lock);
 
 		ret = run_one_delayed_ref(trans, root, ref, extent_op,
@@ -2350,22 +2371,6 @@
 	return count;
 }
 
-static void wait_for_more_refs(struct btrfs_fs_info *fs_info,
-			       struct btrfs_delayed_ref_root *delayed_refs,
-			       unsigned long num_refs,
-			       struct list_head *first_seq)
-{
-	spin_unlock(&delayed_refs->lock);
-	pr_debug("waiting for more refs (num %ld, first %p)\n",
-		 num_refs, first_seq);
-	wait_event(fs_info->tree_mod_seq_wait,
-		   num_refs != delayed_refs->num_entries ||
-		   fs_info->tree_mod_seq_list.next != first_seq);
-	pr_debug("done waiting for more refs (num %ld, first %p)\n",
-		 delayed_refs->num_entries, fs_info->tree_mod_seq_list.next);
-	spin_lock(&delayed_refs->lock);
-}
-
 #ifdef SCRAMBLE_DELAYED_REFS
 /*
  * Normally delayed refs get processed in ascending bytenr order. This
@@ -2460,13 +2465,11 @@
 	struct btrfs_delayed_ref_root *delayed_refs;
 	struct btrfs_delayed_ref_node *ref;
 	struct list_head cluster;
-	struct list_head *first_seq = NULL;
 	int ret;
 	u64 delayed_start;
 	int run_all = count == (unsigned long)-1;
 	int run_most = 0;
-	unsigned long num_refs = 0;
-	int consider_waiting;
+	int loops;
 
 	/* We'll clean this up in btrfs_cleanup_transaction */
 	if (trans->aborted)
@@ -2484,7 +2487,7 @@
 	delayed_refs = &trans->transaction->delayed_refs;
 	INIT_LIST_HEAD(&cluster);
 again:
-	consider_waiting = 0;
+	loops = 0;
 	spin_lock(&delayed_refs->lock);
 
 #ifdef SCRAMBLE_DELAYED_REFS
@@ -2512,31 +2515,6 @@
 		if (ret)
 			break;
 
-		if (delayed_start >= delayed_refs->run_delayed_start) {
-			if (consider_waiting == 0) {
-				/*
-				 * btrfs_find_ref_cluster looped. let's do one
-				 * more cycle. if we don't run any delayed ref
-				 * during that cycle (because we can't because
-				 * all of them are blocked) and if the number of
-				 * refs doesn't change, we avoid busy waiting.
-				 */
-				consider_waiting = 1;
-				num_refs = delayed_refs->num_entries;
-				first_seq = root->fs_info->tree_mod_seq_list.next;
-			} else {
-				wait_for_more_refs(root->fs_info, delayed_refs,
-						   num_refs, first_seq);
-				/*
-				 * after waiting, things have changed. we
-				 * dropped the lock and someone else might have
-				 * run some refs, built new clusters and so on.
-				 * therefore, we restart staleness detection.
-				 */
-				consider_waiting = 0;
-			}
-		}
-
 		ret = run_clustered_refs(trans, root, &cluster);
 		if (ret < 0) {
 			spin_unlock(&delayed_refs->lock);
@@ -2549,9 +2527,26 @@
 		if (count == 0)
 			break;
 
-		if (ret || delayed_refs->run_delayed_start == 0) {
+		if (delayed_start >= delayed_refs->run_delayed_start) {
+			if (loops == 0) {
+				/*
+				 * btrfs_find_ref_cluster looped. let's do one
+				 * more cycle. if we don't run any delayed ref
+				 * during that cycle (because we can't because
+				 * all of them are blocked), bail out.
+				 */
+				loops = 1;
+			} else {
+				/*
+				 * no runnable refs left, stop trying
+				 */
+				BUG_ON(run_all);
+				break;
+			}
+		}
+		if (ret) {
 			/* refs were run, let's reset staleness detection */
-			consider_waiting = 0;
+			loops = 0;
 		}
 	}
 
@@ -3007,17 +3002,16 @@
 	}
 	spin_unlock(&block_group->lock);
 
-	num_pages = (int)div64_u64(block_group->key.offset, 1024 * 1024 * 1024);
+	/*
+	 * Try to preallocate enough space based on how big the block group is.
+	 * Keep in mind this has to include any pinned space which could end up
+	 * taking up quite a bit since it's not folded into the other space
+	 * cache.
+	 */
+	num_pages = (int)div64_u64(block_group->key.offset, 256 * 1024 * 1024);
 	if (!num_pages)
 		num_pages = 1;
 
-	/*
-	 * Just to make absolutely sure we have enough space, we're going to
-	 * preallocate 12 pages worth of space for each block group.  In
-	 * practice we ought to use at most 8, but we need extra space so we can
-	 * add our header and have a terminator between the extents and the
-	 * bitmaps.
-	 */
 	num_pages *= 16;
 	num_pages *= PAGE_CACHE_SIZE;
 
@@ -4571,8 +4565,10 @@
 	if (root->fs_info->quota_enabled) {
 		ret = btrfs_qgroup_reserve(root, num_bytes +
 					   nr_extents * root->leafsize);
-		if (ret)
+		if (ret) {
+			mutex_unlock(&BTRFS_I(inode)->delalloc_mutex);
 			return ret;
+		}
 	}
 
 	ret = reserve_metadata_bytes(root, block_rsv, to_reserve, flush);
@@ -5294,9 +5290,6 @@
 	rb_erase(&head->node.rb_node, &delayed_refs->root);
 
 	delayed_refs->num_entries--;
-	smp_mb();
-	if (waitqueue_active(&root->fs_info->tree_mod_seq_wait))
-		wake_up(&root->fs_info->tree_mod_seq_wait);
 
 	/*
 	 * we don't take a ref on the node because we're removing it from the
diff --git a/fs/btrfs/extent_io.c b/fs/btrfs/extent_io.c
index 45c81bb..4c87847 100644
--- a/fs/btrfs/extent_io.c
+++ b/fs/btrfs/extent_io.c
@@ -2330,23 +2330,10 @@
 		if (uptodate && tree->ops && tree->ops->readpage_end_io_hook) {
 			ret = tree->ops->readpage_end_io_hook(page, start, end,
 							      state, mirror);
-			if (ret) {
-				/* no IO indicated but software detected errors
-				 * in the block, either checksum errors or
-				 * issues with the contents */
-				struct btrfs_root *root =
-					BTRFS_I(page->mapping->host)->root;
-				struct btrfs_device *device;
-
+			if (ret)
 				uptodate = 0;
-				device = btrfs_find_device_for_logical(
-						root, start, mirror);
-				if (device)
-					btrfs_dev_stat_inc_and_print(device,
-						BTRFS_DEV_STAT_CORRUPTION_ERRS);
-			} else {
+			else
 				clean_io_failure(start, page);
-			}
 		}
 
 		if (!uptodate && tree->ops && tree->ops->readpage_io_failed_hook) {
diff --git a/fs/btrfs/file-item.c b/fs/btrfs/file-item.c
index b45b9de..857d93c 100644
--- a/fs/btrfs/file-item.c
+++ b/fs/btrfs/file-item.c
@@ -272,9 +272,9 @@
 }
 
 int btrfs_lookup_bio_sums_dio(struct btrfs_root *root, struct inode *inode,
-			      struct bio *bio, u64 offset, u32 *dst)
+			      struct bio *bio, u64 offset)
 {
-	return __btrfs_lookup_bio_sums(root, inode, bio, offset, dst, 1);
+	return __btrfs_lookup_bio_sums(root, inode, bio, offset, NULL, 1);
 }
 
 int btrfs_lookup_csums_range(struct btrfs_root *root, u64 start, u64 end,
diff --git a/fs/btrfs/inode.c b/fs/btrfs/inode.c
index 6e8f416..ec154f9 100644
--- a/fs/btrfs/inode.c
+++ b/fs/btrfs/inode.c
@@ -1008,9 +1008,7 @@
 	nr_pages = (async_cow->end - async_cow->start + PAGE_CACHE_SIZE) >>
 		PAGE_CACHE_SHIFT;
 
-	atomic_sub(nr_pages, &root->fs_info->async_delalloc_pages);
-
-	if (atomic_read(&root->fs_info->async_delalloc_pages) <
+	if (atomic_sub_return(nr_pages, &root->fs_info->async_delalloc_pages) <
 	    5 * 1024 * 1024 &&
 	    waitqueue_active(&root->fs_info->async_submit_wait))
 		wake_up(&root->fs_info->async_submit_wait);
@@ -1885,8 +1883,11 @@
 				trans = btrfs_join_transaction_nolock(root);
 			else
 				trans = btrfs_join_transaction(root);
-			if (IS_ERR(trans))
-				return PTR_ERR(trans);
+			if (IS_ERR(trans)) {
+				ret = PTR_ERR(trans);
+				trans = NULL;
+				goto out;
+			}
 			trans->block_rsv = &root->fs_info->delalloc_block_rsv;
 			ret = btrfs_update_inode_fallback(trans, root, inode);
 			if (ret) /* -ENOMEM or corruption */
@@ -3174,7 +3175,7 @@
 	btrfs_i_size_write(dir, dir->i_size - name_len * 2);
 	inode_inc_iversion(dir);
 	dir->i_mtime = dir->i_ctime = CURRENT_TIME;
-	ret = btrfs_update_inode(trans, root, dir);
+	ret = btrfs_update_inode_fallback(trans, root, dir);
 	if (ret)
 		btrfs_abort_transaction(trans, root, ret);
 out:
@@ -5774,18 +5775,112 @@
 	return ret;
 }
 
+static int lock_extent_direct(struct inode *inode, u64 lockstart, u64 lockend,
+			      struct extent_state **cached_state, int writing)
+{
+	struct btrfs_ordered_extent *ordered;
+	int ret = 0;
+
+	while (1) {
+		lock_extent_bits(&BTRFS_I(inode)->io_tree, lockstart, lockend,
+				 0, cached_state);
+		/*
+		 * We're concerned with the entire range that we're going to be
+		 * doing DIO to, so we need to make sure theres no ordered
+		 * extents in this range.
+		 */
+		ordered = btrfs_lookup_ordered_range(inode, lockstart,
+						     lockend - lockstart + 1);
+
+		/*
+		 * We need to make sure there are no buffered pages in this
+		 * range either, we could have raced between the invalidate in
+		 * generic_file_direct_write and locking the extent.  The
+		 * invalidate needs to happen so that reads after a write do not
+		 * get stale data.
+		 */
+		if (!ordered && (!writing ||
+		    !test_range_bit(&BTRFS_I(inode)->io_tree,
+				    lockstart, lockend, EXTENT_UPTODATE, 0,
+				    *cached_state)))
+			break;
+
+		unlock_extent_cached(&BTRFS_I(inode)->io_tree, lockstart, lockend,
+				     cached_state, GFP_NOFS);
+
+		if (ordered) {
+			btrfs_start_ordered_extent(inode, ordered, 1);
+			btrfs_put_ordered_extent(ordered);
+		} else {
+			/* Screw you mmap */
+			ret = filemap_write_and_wait_range(inode->i_mapping,
+							   lockstart,
+							   lockend);
+			if (ret)
+				break;
+
+			/*
+			 * If we found a page that couldn't be invalidated just
+			 * fall back to buffered.
+			 */
+			ret = invalidate_inode_pages2_range(inode->i_mapping,
+					lockstart >> PAGE_CACHE_SHIFT,
+					lockend >> PAGE_CACHE_SHIFT);
+			if (ret)
+				break;
+		}
+
+		cond_resched();
+	}
+
+	return ret;
+}
+
 static int btrfs_get_blocks_direct(struct inode *inode, sector_t iblock,
 				   struct buffer_head *bh_result, int create)
 {
 	struct extent_map *em;
 	struct btrfs_root *root = BTRFS_I(inode)->root;
+	struct extent_state *cached_state = NULL;
 	u64 start = iblock << inode->i_blkbits;
+	u64 lockstart, lockend;
 	u64 len = bh_result->b_size;
 	struct btrfs_trans_handle *trans;
+	int unlock_bits = EXTENT_LOCKED;
+	int ret;
+
+	if (create) {
+		ret = btrfs_delalloc_reserve_space(inode, len);
+		if (ret)
+			return ret;
+		unlock_bits |= EXTENT_DELALLOC | EXTENT_DIRTY;
+	} else {
+		len = min_t(u64, len, root->sectorsize);
+	}
+
+	lockstart = start;
+	lockend = start + len - 1;
+
+	/*
+	 * If this errors out it's because we couldn't invalidate pagecache for
+	 * this range and we need to fallback to buffered.
+	 */
+	if (lock_extent_direct(inode, lockstart, lockend, &cached_state, create))
+		return -ENOTBLK;
+
+	if (create) {
+		ret = set_extent_bit(&BTRFS_I(inode)->io_tree, lockstart,
+				     lockend, EXTENT_DELALLOC, NULL,
+				     &cached_state, GFP_NOFS);
+		if (ret)
+			goto unlock_err;
+	}
 
 	em = btrfs_get_extent(inode, NULL, 0, start, len, 0);
-	if (IS_ERR(em))
-		return PTR_ERR(em);
+	if (IS_ERR(em)) {
+		ret = PTR_ERR(em);
+		goto unlock_err;
+	}
 
 	/*
 	 * Ok for INLINE and COMPRESSED extents we need to fallback on buffered
@@ -5804,17 +5899,16 @@
 	if (test_bit(EXTENT_FLAG_COMPRESSED, &em->flags) ||
 	    em->block_start == EXTENT_MAP_INLINE) {
 		free_extent_map(em);
-		return -ENOTBLK;
+		ret = -ENOTBLK;
+		goto unlock_err;
 	}
 
 	/* Just a good old fashioned hole, return */
 	if (!create && (em->block_start == EXTENT_MAP_HOLE ||
 			test_bit(EXTENT_FLAG_PREALLOC, &em->flags))) {
 		free_extent_map(em);
-		/* DIO will do one hole at a time, so just unlock a sector */
-		unlock_extent(&BTRFS_I(inode)->io_tree, start,
-			      start + root->sectorsize - 1);
-		return 0;
+		ret = 0;
+		goto unlock_err;
 	}
 
 	/*
@@ -5827,8 +5921,9 @@
 	 *
 	 */
 	if (!create) {
-		len = em->len - (start - em->start);
-		goto map;
+		len = min(len, em->len - (start - em->start));
+		lockstart = start + len;
+		goto unlock;
 	}
 
 	if (test_bit(EXTENT_FLAG_PREALLOC, &em->flags) ||
@@ -5860,7 +5955,7 @@
 			btrfs_end_transaction(trans, root);
 			if (ret) {
 				free_extent_map(em);
-				return ret;
+				goto unlock_err;
 			}
 			goto unlock;
 		}
@@ -5873,14 +5968,12 @@
 	 */
 	len = bh_result->b_size;
 	em = btrfs_new_extent_direct(inode, em, start, len);
-	if (IS_ERR(em))
-		return PTR_ERR(em);
+	if (IS_ERR(em)) {
+		ret = PTR_ERR(em);
+		goto unlock_err;
+	}
 	len = min(len, em->len - (start - em->start));
 unlock:
-	clear_extent_bit(&BTRFS_I(inode)->io_tree, start, start + len - 1,
-			  EXTENT_LOCKED | EXTENT_DELALLOC | EXTENT_DIRTY, 1,
-			  0, NULL, GFP_NOFS);
-map:
 	bh_result->b_blocknr = (em->block_start + (start - em->start)) >>
 		inode->i_blkbits;
 	bh_result->b_size = len;
@@ -5898,9 +5991,44 @@
 			i_size_write(inode, start + len);
 	}
 
+	/*
+	 * In the case of write we need to clear and unlock the entire range,
+	 * in the case of read we need to unlock only the end area that we
+	 * aren't using if there is any left over space.
+	 */
+	if (lockstart < lockend) {
+		if (create && len < lockend - lockstart) {
+			clear_extent_bit(&BTRFS_I(inode)->io_tree, lockstart,
+					 lockstart + len - 1, unlock_bits, 1, 0,
+					 &cached_state, GFP_NOFS);
+			/*
+			 * Beside unlock, we also need to cleanup reserved space
+			 * for the left range by attaching EXTENT_DO_ACCOUNTING.
+			 */
+			clear_extent_bit(&BTRFS_I(inode)->io_tree,
+					 lockstart + len, lockend,
+					 unlock_bits | EXTENT_DO_ACCOUNTING,
+					 1, 0, NULL, GFP_NOFS);
+		} else {
+			clear_extent_bit(&BTRFS_I(inode)->io_tree, lockstart,
+					 lockend, unlock_bits, 1, 0,
+					 &cached_state, GFP_NOFS);
+		}
+	} else {
+		free_extent_state(cached_state);
+	}
+
 	free_extent_map(em);
 
 	return 0;
+
+unlock_err:
+	if (create)
+		unlock_bits |= EXTENT_DO_ACCOUNTING;
+
+	clear_extent_bit(&BTRFS_I(inode)->io_tree, lockstart, lockend,
+			 unlock_bits, 1, 0, &cached_state, GFP_NOFS);
+	return ret;
 }
 
 struct btrfs_dio_private {
@@ -5908,7 +6036,6 @@
 	u64 logical_offset;
 	u64 disk_bytenr;
 	u64 bytes;
-	u32 *csums;
 	void *private;
 
 	/* number of bios pending for this dio */
@@ -5928,7 +6055,6 @@
 	struct inode *inode = dip->inode;
 	struct btrfs_root *root = BTRFS_I(inode)->root;
 	u64 start;
-	u32 *private = dip->csums;
 
 	start = dip->logical_offset;
 	do {
@@ -5936,8 +6062,12 @@
 			struct page *page = bvec->bv_page;
 			char *kaddr;
 			u32 csum = ~(u32)0;
+			u64 private = ~(u32)0;
 			unsigned long flags;
 
+			if (get_state_private(&BTRFS_I(inode)->io_tree,
+					      start, &private))
+				goto failed;
 			local_irq_save(flags);
 			kaddr = kmap_atomic(page);
 			csum = btrfs_csum_data(root, kaddr + bvec->bv_offset,
@@ -5947,18 +6077,18 @@
 			local_irq_restore(flags);
 
 			flush_dcache_page(bvec->bv_page);
-			if (csum != *private) {
+			if (csum != private) {
+failed:
 				printk(KERN_ERR "btrfs csum failed ino %llu off"
 				      " %llu csum %u private %u\n",
 				      (unsigned long long)btrfs_ino(inode),
 				      (unsigned long long)start,
-				      csum, *private);
+				      csum, (unsigned)private);
 				err = -EIO;
 			}
 		}
 
 		start += bvec->bv_len;
-		private++;
 		bvec++;
 	} while (bvec <= bvec_end);
 
@@ -5966,7 +6096,6 @@
 		      dip->logical_offset + dip->bytes - 1);
 	bio->bi_private = dip->private;
 
-	kfree(dip->csums);
 	kfree(dip);
 
 	/* If we had a csum failure make sure to clear the uptodate flag */
@@ -6072,7 +6201,7 @@
 
 static inline int __btrfs_submit_dio_bio(struct bio *bio, struct inode *inode,
 					 int rw, u64 file_offset, int skip_sum,
-					 u32 *csums, int async_submit)
+					 int async_submit)
 {
 	int write = rw & REQ_WRITE;
 	struct btrfs_root *root = BTRFS_I(inode)->root;
@@ -6105,8 +6234,7 @@
 		if (ret)
 			goto err;
 	} else if (!skip_sum) {
-		ret = btrfs_lookup_bio_sums_dio(root, inode, bio,
-					  file_offset, csums);
+		ret = btrfs_lookup_bio_sums_dio(root, inode, bio, file_offset);
 		if (ret)
 			goto err;
 	}
@@ -6132,10 +6260,8 @@
 	u64 submit_len = 0;
 	u64 map_length;
 	int nr_pages = 0;
-	u32 *csums = dip->csums;
 	int ret = 0;
 	int async_submit = 0;
-	int write = rw & REQ_WRITE;
 
 	map_length = orig_bio->bi_size;
 	ret = btrfs_map_block(map_tree, READ, start_sector << 9,
@@ -6171,16 +6297,13 @@
 			atomic_inc(&dip->pending_bios);
 			ret = __btrfs_submit_dio_bio(bio, inode, rw,
 						     file_offset, skip_sum,
-						     csums, async_submit);
+						     async_submit);
 			if (ret) {
 				bio_put(bio);
 				atomic_dec(&dip->pending_bios);
 				goto out_err;
 			}
 
-			/* Write's use the ordered csums */
-			if (!write && !skip_sum)
-				csums = csums + nr_pages;
 			start_sector += submit_len >> 9;
 			file_offset += submit_len;
 
@@ -6210,7 +6333,7 @@
 
 submit:
 	ret = __btrfs_submit_dio_bio(bio, inode, rw, file_offset, skip_sum,
-				     csums, async_submit);
+				     async_submit);
 	if (!ret)
 		return 0;
 
@@ -6246,17 +6369,6 @@
 		ret = -ENOMEM;
 		goto free_ordered;
 	}
-	dip->csums = NULL;
-
-	/* Write's use the ordered csum stuff, so we don't need dip->csums */
-	if (!write && !skip_sum) {
-		dip->csums = kmalloc(sizeof(u32) * bio->bi_vcnt, GFP_NOFS);
-		if (!dip->csums) {
-			kfree(dip);
-			ret = -ENOMEM;
-			goto free_ordered;
-		}
-	}
 
 	dip->private = bio->bi_private;
 	dip->inode = inode;
@@ -6341,132 +6453,22 @@
 out:
 	return retval;
 }
+
 static ssize_t btrfs_direct_IO(int rw, struct kiocb *iocb,
 			const struct iovec *iov, loff_t offset,
 			unsigned long nr_segs)
 {
 	struct file *file = iocb->ki_filp;
 	struct inode *inode = file->f_mapping->host;
-	struct btrfs_ordered_extent *ordered;
-	struct extent_state *cached_state = NULL;
-	u64 lockstart, lockend;
-	ssize_t ret;
-	int writing = rw & WRITE;
-	int write_bits = 0;
-	size_t count = iov_length(iov, nr_segs);
 
 	if (check_direct_IO(BTRFS_I(inode)->root, rw, iocb, iov,
-			    offset, nr_segs)) {
+			    offset, nr_segs))
 		return 0;
-	}
 
-	lockstart = offset;
-	lockend = offset + count - 1;
-
-	if (writing) {
-		ret = btrfs_delalloc_reserve_space(inode, count);
-		if (ret)
-			goto out;
-	}
-
-	while (1) {
-		lock_extent_bits(&BTRFS_I(inode)->io_tree, lockstart, lockend,
-				 0, &cached_state);
-		/*
-		 * We're concerned with the entire range that we're going to be
-		 * doing DIO to, so we need to make sure theres no ordered
-		 * extents in this range.
-		 */
-		ordered = btrfs_lookup_ordered_range(inode, lockstart,
-						     lockend - lockstart + 1);
-
-		/*
-		 * We need to make sure there are no buffered pages in this
-		 * range either, we could have raced between the invalidate in
-		 * generic_file_direct_write and locking the extent.  The
-		 * invalidate needs to happen so that reads after a write do not
-		 * get stale data.
-		 */
-		if (!ordered && (!writing ||
-		    !test_range_bit(&BTRFS_I(inode)->io_tree,
-				    lockstart, lockend, EXTENT_UPTODATE, 0,
-				    cached_state)))
-			break;
-
-		unlock_extent_cached(&BTRFS_I(inode)->io_tree, lockstart, lockend,
-				     &cached_state, GFP_NOFS);
-
-		if (ordered) {
-			btrfs_start_ordered_extent(inode, ordered, 1);
-			btrfs_put_ordered_extent(ordered);
-		} else {
-			/* Screw you mmap */
-			ret = filemap_write_and_wait_range(file->f_mapping,
-							   lockstart,
-							   lockend);
-			if (ret)
-				goto out;
-
-			/*
-			 * If we found a page that couldn't be invalidated just
-			 * fall back to buffered.
-			 */
-			ret = invalidate_inode_pages2_range(file->f_mapping,
-					lockstart >> PAGE_CACHE_SHIFT,
-					lockend >> PAGE_CACHE_SHIFT);
-			if (ret) {
-				if (ret == -EBUSY)
-					ret = 0;
-				goto out;
-			}
-		}
-
-		cond_resched();
-	}
-
-	/*
-	 * we don't use btrfs_set_extent_delalloc because we don't want
-	 * the dirty or uptodate bits
-	 */
-	if (writing) {
-		write_bits = EXTENT_DELALLOC | EXTENT_DO_ACCOUNTING;
-		ret = set_extent_bit(&BTRFS_I(inode)->io_tree, lockstart, lockend,
-				     EXTENT_DELALLOC, NULL, &cached_state,
-				     GFP_NOFS);
-		if (ret) {
-			clear_extent_bit(&BTRFS_I(inode)->io_tree, lockstart,
-					 lockend, EXTENT_LOCKED | write_bits,
-					 1, 0, &cached_state, GFP_NOFS);
-			goto out;
-		}
-	}
-
-	free_extent_state(cached_state);
-	cached_state = NULL;
-
-	ret = __blockdev_direct_IO(rw, iocb, inode,
+	return __blockdev_direct_IO(rw, iocb, inode,
 		   BTRFS_I(inode)->root->fs_info->fs_devices->latest_bdev,
 		   iov, offset, nr_segs, btrfs_get_blocks_direct, NULL,
 		   btrfs_submit_direct, 0);
-
-	if (ret < 0 && ret != -EIOCBQUEUED) {
-		clear_extent_bit(&BTRFS_I(inode)->io_tree, offset,
-			      offset + iov_length(iov, nr_segs) - 1,
-			      EXTENT_LOCKED | write_bits, 1, 0,
-			      &cached_state, GFP_NOFS);
-	} else if (ret >= 0 && ret < iov_length(iov, nr_segs)) {
-		/*
-		 * We're falling back to buffered, unlock the section we didn't
-		 * do IO on.
-		 */
-		clear_extent_bit(&BTRFS_I(inode)->io_tree, offset + ret,
-			      offset + iov_length(iov, nr_segs) - 1,
-			      EXTENT_LOCKED | write_bits, 1, 0,
-			      &cached_state, GFP_NOFS);
-	}
-out:
-	free_extent_state(cached_state);
-	return ret;
 }
 
 static int btrfs_fiemap(struct inode *inode, struct fiemap_extent_info *fieinfo,
diff --git a/fs/btrfs/ioctl.c b/fs/btrfs/ioctl.c
index 7bb7556..9df50fa 100644
--- a/fs/btrfs/ioctl.c
+++ b/fs/btrfs/ioctl.c
@@ -424,7 +424,7 @@
 	uuid_le_gen(&new_uuid);
 	memcpy(root_item.uuid, new_uuid.b, BTRFS_UUID_SIZE);
 	root_item.otime.sec = cpu_to_le64(cur_time.tv_sec);
-	root_item.otime.nsec = cpu_to_le64(cur_time.tv_nsec);
+	root_item.otime.nsec = cpu_to_le32(cur_time.tv_nsec);
 	root_item.ctime = root_item.otime;
 	btrfs_set_root_ctransid(&root_item, trans->transid);
 	btrfs_set_root_otransid(&root_item, trans->transid);
diff --git a/fs/btrfs/locking.c b/fs/btrfs/locking.c
index a44eff074..2a1762c 100644
--- a/fs/btrfs/locking.c
+++ b/fs/btrfs/locking.c
@@ -67,7 +67,7 @@
 {
 	if (eb->lock_nested) {
 		read_lock(&eb->lock);
-		if (&eb->lock_nested && current->pid == eb->lock_owner) {
+		if (eb->lock_nested && current->pid == eb->lock_owner) {
 			read_unlock(&eb->lock);
 			return;
 		}
diff --git a/fs/btrfs/qgroup.c b/fs/btrfs/qgroup.c
index bc424ae..38b42e7 100644
--- a/fs/btrfs/qgroup.c
+++ b/fs/btrfs/qgroup.c
@@ -1364,13 +1364,17 @@
 	spin_lock(&fs_info->qgroup_lock);
 
 	dstgroup = add_qgroup_rb(fs_info, objectid);
-	if (!dstgroup)
+	if (IS_ERR(dstgroup)) {
+		ret = PTR_ERR(dstgroup);
 		goto unlock;
+	}
 
 	if (srcid) {
 		srcgroup = find_qgroup_rb(fs_info, srcid);
-		if (!srcgroup)
+		if (!srcgroup) {
+			ret = -EINVAL;
 			goto unlock;
+		}
 		dstgroup->rfer = srcgroup->rfer - level_size;
 		dstgroup->rfer_cmpr = srcgroup->rfer_cmpr - level_size;
 		srcgroup->excl = level_size;
@@ -1379,8 +1383,10 @@
 		qgroup_dirty(fs_info, srcgroup);
 	}
 
-	if (!inherit)
+	if (!inherit) {
+		ret = -EINVAL;
 		goto unlock;
+	}
 
 	i_qgroups = (u64 *)(inherit + 1);
 	for (i = 0; i < inherit->num_qgroups; ++i) {
diff --git a/fs/btrfs/root-tree.c b/fs/btrfs/root-tree.c
index 6bb465c..10d8e4d 100644
--- a/fs/btrfs/root-tree.c
+++ b/fs/btrfs/root-tree.c
@@ -544,8 +544,8 @@
 	struct timespec ct = CURRENT_TIME;
 
 	spin_lock(&root->root_times_lock);
-	item->ctransid = trans->transid;
+	item->ctransid = cpu_to_le64(trans->transid);
 	item->ctime.sec = cpu_to_le64(ct.tv_sec);
-	item->ctime.nsec = cpu_to_le64(ct.tv_nsec);
+	item->ctime.nsec = cpu_to_le32(ct.tv_nsec);
 	spin_unlock(&root->root_times_lock);
 }
diff --git a/fs/btrfs/super.c b/fs/btrfs/super.c
index f2eb24c..83d6f9f 100644
--- a/fs/btrfs/super.c
+++ b/fs/btrfs/super.c
@@ -838,7 +838,6 @@
 	struct btrfs_trans_handle *trans;
 	struct btrfs_fs_info *fs_info = btrfs_sb(sb);
 	struct btrfs_root *root = fs_info->tree_root;
-	int ret;
 
 	trace_btrfs_sync_fs(wait);
 
@@ -849,11 +848,17 @@
 
 	btrfs_wait_ordered_extents(root, 0, 0);
 
-	trans = btrfs_start_transaction(root, 0);
+	spin_lock(&fs_info->trans_lock);
+	if (!fs_info->running_transaction) {
+		spin_unlock(&fs_info->trans_lock);
+		return 0;
+	}
+	spin_unlock(&fs_info->trans_lock);
+
+	trans = btrfs_join_transaction(root);
 	if (IS_ERR(trans))
 		return PTR_ERR(trans);
-	ret = btrfs_commit_transaction(trans, root);
-	return ret;
+	return btrfs_commit_transaction(trans, root);
 }
 
 static int btrfs_show_options(struct seq_file *seq, struct dentry *dentry)
@@ -1530,6 +1535,8 @@
 	while (cur_devices) {
 		head = &cur_devices->devices;
 		list_for_each_entry(dev, head, dev_list) {
+			if (dev->missing)
+				continue;
 			if (!first_dev || dev->devid < first_dev->devid)
 				first_dev = dev;
 		}
diff --git a/fs/btrfs/transaction.c b/fs/btrfs/transaction.c
index 17be3de..27c2600 100644
--- a/fs/btrfs/transaction.c
+++ b/fs/btrfs/transaction.c
@@ -1031,6 +1031,7 @@
 
 	btrfs_i_size_write(parent_inode, parent_inode->i_size +
 					 dentry->d_name.len * 2);
+	parent_inode->i_mtime = parent_inode->i_ctime = CURRENT_TIME;
 	ret = btrfs_update_inode(trans, parent_root, parent_inode);
 	if (ret)
 		goto abort_trans_dput;
@@ -1066,7 +1067,7 @@
 	memcpy(new_root_item->parent_uuid, root->root_item.uuid,
 			BTRFS_UUID_SIZE);
 	new_root_item->otime.sec = cpu_to_le64(cur_time.tv_sec);
-	new_root_item->otime.nsec = cpu_to_le64(cur_time.tv_nsec);
+	new_root_item->otime.nsec = cpu_to_le32(cur_time.tv_nsec);
 	btrfs_set_root_otransid(new_root_item, trans->transid);
 	memset(&new_root_item->stime, 0, sizeof(new_root_item->stime));
 	memset(&new_root_item->rtime, 0, sizeof(new_root_item->rtime));
diff --git a/fs/btrfs/volumes.c b/fs/btrfs/volumes.c
index e86ae04..88b969a 100644
--- a/fs/btrfs/volumes.c
+++ b/fs/btrfs/volumes.c
@@ -227,9 +227,8 @@
 		cur = pending;
 		pending = pending->bi_next;
 		cur->bi_next = NULL;
-		atomic_dec(&fs_info->nr_async_bios);
 
-		if (atomic_read(&fs_info->nr_async_bios) < limit &&
+		if (atomic_dec_return(&fs_info->nr_async_bios) < limit &&
 		    waitqueue_active(&fs_info->async_submit_wait))
 			wake_up(&fs_info->async_submit_wait);
 
@@ -569,9 +568,11 @@
 		memcpy(new_device, device, sizeof(*new_device));
 
 		/* Safe because we are under uuid_mutex */
-		name = rcu_string_strdup(device->name->str, GFP_NOFS);
-		BUG_ON(device->name && !name); /* -ENOMEM */
-		rcu_assign_pointer(new_device->name, name);
+		if (device->name) {
+			name = rcu_string_strdup(device->name->str, GFP_NOFS);
+			BUG_ON(device->name && !name); /* -ENOMEM */
+			rcu_assign_pointer(new_device->name, name);
+		}
 		new_device->bdev = NULL;
 		new_device->writeable = 0;
 		new_device->in_fs_metadata = 0;
@@ -4605,28 +4606,6 @@
 	return ret;
 }
 
-struct btrfs_device *btrfs_find_device_for_logical(struct btrfs_root *root,
-						   u64 logical, int mirror_num)
-{
-	struct btrfs_mapping_tree *map_tree = &root->fs_info->mapping_tree;
-	int ret;
-	u64 map_length = 0;
-	struct btrfs_bio *bbio = NULL;
-	struct btrfs_device *device;
-
-	BUG_ON(mirror_num == 0);
-	ret = btrfs_map_block(map_tree, WRITE, logical, &map_length, &bbio,
-			      mirror_num);
-	if (ret) {
-		BUG_ON(bbio != NULL);
-		return NULL;
-	}
-	BUG_ON(mirror_num != bbio->mirror_num);
-	device = bbio->stripes[mirror_num - 1].dev;
-	kfree(bbio);
-	return device;
-}
-
 int btrfs_read_chunk_tree(struct btrfs_root *root)
 {
 	struct btrfs_path *path;
diff --git a/fs/btrfs/volumes.h b/fs/btrfs/volumes.h
index 5479325..53c06af 100644
--- a/fs/btrfs/volumes.h
+++ b/fs/btrfs/volumes.h
@@ -289,8 +289,6 @@
 int btrfs_chunk_readonly(struct btrfs_root *root, u64 chunk_offset);
 int find_free_dev_extent(struct btrfs_device *device, u64 num_bytes,
 			 u64 *start, u64 *max_avail);
-struct btrfs_device *btrfs_find_device_for_logical(struct btrfs_root *root,
-						   u64 logical, int mirror_num);
 void btrfs_dev_stat_print_on_error(struct btrfs_device *device);
 void btrfs_dev_stat_inc_and_print(struct btrfs_device *dev, int index);
 int btrfs_get_dev_stats(struct btrfs_root *root,
diff --git a/fs/buffer.c b/fs/buffer.c
index 9f6d2e4..58e2e7b 100644
--- a/fs/buffer.c
+++ b/fs/buffer.c
@@ -914,7 +914,7 @@
 /*
  * Initialise the state of a blockdev page's buffers.
  */ 
-static void
+static sector_t
 init_page_buffers(struct page *page, struct block_device *bdev,
 			sector_t block, int size)
 {
@@ -936,33 +936,41 @@
 		block++;
 		bh = bh->b_this_page;
 	} while (bh != head);
+
+	/*
+	 * Caller needs to validate requested block against end of device.
+	 */
+	return end_block;
 }
 
 /*
  * Create the page-cache page that contains the requested block.
  *
- * This is user purely for blockdev mappings.
+ * This is used purely for blockdev mappings.
  */
-static struct page *
+static int
 grow_dev_page(struct block_device *bdev, sector_t block,
-		pgoff_t index, int size)
+		pgoff_t index, int size, int sizebits)
 {
 	struct inode *inode = bdev->bd_inode;
 	struct page *page;
 	struct buffer_head *bh;
+	sector_t end_block;
+	int ret = 0;		/* Will call free_more_memory() */
 
 	page = find_or_create_page(inode->i_mapping, index,
 		(mapping_gfp_mask(inode->i_mapping) & ~__GFP_FS)|__GFP_MOVABLE);
 	if (!page)
-		return NULL;
+		return ret;
 
 	BUG_ON(!PageLocked(page));
 
 	if (page_has_buffers(page)) {
 		bh = page_buffers(page);
 		if (bh->b_size == size) {
-			init_page_buffers(page, bdev, block, size);
-			return page;
+			end_block = init_page_buffers(page, bdev,
+						index << sizebits, size);
+			goto done;
 		}
 		if (!try_to_free_buffers(page))
 			goto failed;
@@ -982,14 +990,14 @@
 	 */
 	spin_lock(&inode->i_mapping->private_lock);
 	link_dev_buffers(page, bh);
-	init_page_buffers(page, bdev, block, size);
+	end_block = init_page_buffers(page, bdev, index << sizebits, size);
 	spin_unlock(&inode->i_mapping->private_lock);
-	return page;
-
+done:
+	ret = (block < end_block) ? 1 : -ENXIO;
 failed:
 	unlock_page(page);
 	page_cache_release(page);
-	return NULL;
+	return ret;
 }
 
 /*
@@ -999,7 +1007,6 @@
 static int
 grow_buffers(struct block_device *bdev, sector_t block, int size)
 {
-	struct page *page;
 	pgoff_t index;
 	int sizebits;
 
@@ -1023,22 +1030,14 @@
 			bdevname(bdev, b));
 		return -EIO;
 	}
-	block = index << sizebits;
+
 	/* Create a page with the proper size buffers.. */
-	page = grow_dev_page(bdev, block, index, size);
-	if (!page)
-		return 0;
-	unlock_page(page);
-	page_cache_release(page);
-	return 1;
+	return grow_dev_page(bdev, block, index, size, sizebits);
 }
 
 static struct buffer_head *
 __getblk_slow(struct block_device *bdev, sector_t block, int size)
 {
-	int ret;
-	struct buffer_head *bh;
-
 	/* Size must be multiple of hard sectorsize */
 	if (unlikely(size & (bdev_logical_block_size(bdev)-1) ||
 			(size < 512 || size > PAGE_SIZE))) {
@@ -1051,21 +1050,20 @@
 		return NULL;
 	}
 
-retry:
-	bh = __find_get_block(bdev, block, size);
-	if (bh)
-		return bh;
+	for (;;) {
+		struct buffer_head *bh;
+		int ret;
 
-	ret = grow_buffers(bdev, block, size);
-	if (ret == 0) {
-		free_more_memory();
-		goto retry;
-	} else if (ret > 0) {
 		bh = __find_get_block(bdev, block, size);
 		if (bh)
 			return bh;
+
+		ret = grow_buffers(bdev, block, size);
+		if (ret < 0)
+			return NULL;
+		if (ret == 0)
+			free_more_memory();
 	}
-	return NULL;
 }
 
 /*
@@ -1321,10 +1319,6 @@
  * which corresponds to the passed block_device, block and size. The
  * returned buffer has its reference count incremented.
  *
- * __getblk() cannot fail - it just keeps trying.  If you pass it an
- * illegal block number, __getblk() will happily return a buffer_head
- * which represents the non-existent block.  Very weird.
- *
  * __getblk() will lock up the machine if grow_dev_page's try_to_free_buffers()
  * attempt is failing.  FIXME, perhaps?
  */
diff --git a/fs/cifs/cifssmb.c b/fs/cifs/cifssmb.c
index 074923c..f0cf934 100644
--- a/fs/cifs/cifssmb.c
+++ b/fs/cifs/cifssmb.c
@@ -1576,9 +1576,14 @@
 		/* result already set, check signature */
 		if (server->sec_mode &
 		    (SECMODE_SIGN_REQUIRED | SECMODE_SIGN_ENABLED)) {
-			if (cifs_verify_signature(rdata->iov, rdata->nr_iov,
-					  server, mid->sequence_number + 1))
-				cERROR(1, "Unexpected SMB signature");
+			int rc = 0;
+
+			rc = cifs_verify_signature(rdata->iov, rdata->nr_iov,
+						   server,
+						   mid->sequence_number + 1);
+			if (rc)
+				cERROR(1, "SMB signature verification returned "
+				       "error = %d", rc);
 		}
 		/* FIXME: should this be counted toward the initiating task? */
 		task_io_account_read(rdata->bytes);
diff --git a/fs/cifs/dir.c b/fs/cifs/dir.c
index cbe709a..781025b 100644
--- a/fs/cifs/dir.c
+++ b/fs/cifs/dir.c
@@ -356,19 +356,12 @@
 cifs_create_set_dentry:
 	if (rc != 0) {
 		cFYI(1, "Create worked, get_inode_info failed rc = %d", rc);
+		CIFSSMBClose(xid, tcon, *fileHandle);
 		goto out;
 	}
 	d_drop(direntry);
 	d_add(direntry, newinode);
 
-	/* ENOENT for create?  How weird... */
-	rc = -ENOENT;
-	if (!newinode) {
-		CIFSSMBClose(xid, tcon, *fileHandle);
-		goto out;
-	}
-	rc = 0;
-
 out:
 	kfree(buf);
 	kfree(full_path);
diff --git a/fs/cifs/inode.c b/fs/cifs/inode.c
index 7354877..cb79c7e 100644
--- a/fs/cifs/inode.c
+++ b/fs/cifs/inode.c
@@ -124,10 +124,10 @@
 {
 	struct cifsInodeInfo *cifs_i = CIFS_I(inode);
 	struct cifs_sb_info *cifs_sb = CIFS_SB(inode->i_sb);
-	unsigned long oldtime = cifs_i->time;
 
 	cifs_revalidate_cache(inode, fattr);
 
+	spin_lock(&inode->i_lock);
 	inode->i_atime = fattr->cf_atime;
 	inode->i_mtime = fattr->cf_mtime;
 	inode->i_ctime = fattr->cf_ctime;
@@ -148,9 +148,6 @@
 	else
 		cifs_i->time = jiffies;
 
-	cFYI(1, "inode 0x%p old_time=%ld new_time=%ld", inode,
-		 oldtime, cifs_i->time);
-
 	cifs_i->delete_pending = fattr->cf_flags & CIFS_FATTR_DELETE_PENDING;
 
 	cifs_i->server_eof = fattr->cf_eof;
@@ -158,7 +155,6 @@
 	 * Can't safely change the file size here if the client is writing to
 	 * it due to potential races.
 	 */
-	spin_lock(&inode->i_lock);
 	if (is_size_safe_to_change(cifs_i, fattr->cf_eof)) {
 		i_size_write(inode, fattr->cf_eof);
 
@@ -859,12 +855,14 @@
 
 	if (rc && tcon->ipc) {
 		cFYI(1, "ipc connection - fake read inode");
+		spin_lock(&inode->i_lock);
 		inode->i_mode |= S_IFDIR;
 		set_nlink(inode, 2);
 		inode->i_op = &cifs_ipc_inode_ops;
 		inode->i_fop = &simple_dir_operations;
 		inode->i_uid = cifs_sb->mnt_uid;
 		inode->i_gid = cifs_sb->mnt_gid;
+		spin_unlock(&inode->i_lock);
 	} else if (rc) {
 		iget_failed(inode);
 		inode = ERR_PTR(rc);
@@ -1110,6 +1108,15 @@
 	goto out_close;
 }
 
+/* copied from fs/nfs/dir.c with small changes */
+static void
+cifs_drop_nlink(struct inode *inode)
+{
+	spin_lock(&inode->i_lock);
+	if (inode->i_nlink > 0)
+		drop_nlink(inode);
+	spin_unlock(&inode->i_lock);
+}
 
 /*
  * If dentry->d_inode is null (usually meaning the cached dentry
@@ -1166,13 +1173,13 @@
 psx_del_no_retry:
 	if (!rc) {
 		if (inode)
-			drop_nlink(inode);
+			cifs_drop_nlink(inode);
 	} else if (rc == -ENOENT) {
 		d_drop(dentry);
 	} else if (rc == -ETXTBSY) {
 		rc = cifs_rename_pending_delete(full_path, dentry, xid);
 		if (rc == 0)
-			drop_nlink(inode);
+			cifs_drop_nlink(inode);
 	} else if ((rc == -EACCES) && (dosattr == 0) && inode) {
 		attrs = kzalloc(sizeof(*attrs), GFP_KERNEL);
 		if (attrs == NULL) {
@@ -1241,9 +1248,10 @@
 	 * setting nlink not necessary except in cases where we failed to get it
 	 * from the server or was set bogus
 	 */
+	spin_lock(&dentry->d_inode->i_lock);
 	if ((dentry->d_inode) && (dentry->d_inode->i_nlink < 2))
 		set_nlink(dentry->d_inode, 2);
-
+	spin_unlock(&dentry->d_inode->i_lock);
 	mode &= ~current_umask();
 	/* must turn on setgid bit if parent dir has it */
 	if (inode->i_mode & S_ISGID)
diff --git a/fs/cifs/link.c b/fs/cifs/link.c
index 09e4b3a..e6ce3b1 100644
--- a/fs/cifs/link.c
+++ b/fs/cifs/link.c
@@ -433,7 +433,9 @@
 	if (old_file->d_inode) {
 		cifsInode = CIFS_I(old_file->d_inode);
 		if (rc == 0) {
+			spin_lock(&old_file->d_inode->i_lock);
 			inc_nlink(old_file->d_inode);
+			spin_unlock(&old_file->d_inode->i_lock);
 /* BB should we make this contingent on superblock flag NOATIME? */
 /*			old_file->d_inode->i_ctime = CURRENT_TIME;*/
 			/* parent dir timestamps will update from srv
diff --git a/fs/cifs/smb2misc.c b/fs/cifs/smb2misc.c
index a4ff5d5..e4d3b99 100644
--- a/fs/cifs/smb2misc.c
+++ b/fs/cifs/smb2misc.c
@@ -52,7 +52,8 @@
 			cERROR(1, "Bad protocol string signature header %x",
 				  *(unsigned int *) hdr->ProtocolId);
 		if (mid != hdr->MessageId)
-			cERROR(1, "Mids do not match");
+			cERROR(1, "Mids do not match: %llu and %llu", mid,
+				  hdr->MessageId);
 	}
 	cERROR(1, "Bad SMB detected. The Mid=%llu", hdr->MessageId);
 	return 1;
@@ -107,7 +108,7 @@
 	 * ie Validate the wct via smb2_struct_sizes table above
 	 */
 
-	if (length < 2 + sizeof(struct smb2_hdr)) {
+	if (length < sizeof(struct smb2_pdu)) {
 		if ((length >= sizeof(struct smb2_hdr)) && (hdr->Status != 0)) {
 			pdu->StructureSize2 = 0;
 			/*
@@ -121,15 +122,15 @@
 		return 1;
 	}
 	if (len > CIFSMaxBufSize + MAX_SMB2_HDR_SIZE - 4) {
-		cERROR(1, "SMB length greater than maximum, mid=%lld", mid);
+		cERROR(1, "SMB length greater than maximum, mid=%llu", mid);
 		return 1;
 	}
 
 	if (check_smb2_hdr(hdr, mid))
 		return 1;
 
-	if (hdr->StructureSize != SMB2_HEADER_SIZE) {
-		cERROR(1, "Illegal structure size %d",
+	if (hdr->StructureSize != SMB2_HEADER_STRUCTURE_SIZE) {
+		cERROR(1, "Illegal structure size %u",
 			  le16_to_cpu(hdr->StructureSize));
 		return 1;
 	}
@@ -161,8 +162,9 @@
 	if (4 + len != clc_len) {
 		cFYI(1, "Calculated size %u length %u mismatch mid %llu",
 			clc_len, 4 + len, mid);
-		if (clc_len == 4 + len + 1) /* BB FIXME (fix samba) */
-			return 0; /* BB workaround Samba 3 bug SessSetup rsp */
+		/* server can return one byte more */
+		if (clc_len == 4 + len + 1)
+			return 0;
 		return 1;
 	}
 	return 0;
diff --git a/fs/cifs/smb2pdu.h b/fs/cifs/smb2pdu.h
index f37a1b4..c5fbfac 100644
--- a/fs/cifs/smb2pdu.h
+++ b/fs/cifs/smb2pdu.h
@@ -87,10 +87,6 @@
 
 #define SMB2_PROTO_NUMBER __constant_cpu_to_le32(0x424d53fe)
 
-#define SMB2_HEADER_SIZE __constant_le16_to_cpu(64)
-
-#define SMB2_ERROR_STRUCTURE_SIZE2 __constant_le16_to_cpu(9)
-
 /*
  * SMB2 Header Definition
  *
@@ -99,6 +95,9 @@
  * "PDU" :  "Protocol Data Unit" (ie a network "frame")
  *
  */
+
+#define SMB2_HEADER_STRUCTURE_SIZE __constant_le16_to_cpu(64)
+
 struct smb2_hdr {
 	__be32 smb2_buf_length;	/* big endian on wire */
 				/* length is only two or three bytes - with
@@ -140,6 +139,9 @@
  *  command code name for the struct. Note that structures must be packed.
  *
  */
+
+#define SMB2_ERROR_STRUCTURE_SIZE2 __constant_le16_to_cpu(9)
+
 struct smb2_err_rsp {
 	struct smb2_hdr hdr;
 	__le16 StructureSize;
diff --git a/fs/cifs/transport.c b/fs/cifs/transport.c
index 83867ef..d9b639b 100644
--- a/fs/cifs/transport.c
+++ b/fs/cifs/transport.c
@@ -503,13 +503,16 @@
 	/* convert the length into a more usable form */
 	if (server->sec_mode & (SECMODE_SIGN_REQUIRED | SECMODE_SIGN_ENABLED)) {
 		struct kvec iov;
+		int rc = 0;
 
 		iov.iov_base = mid->resp_buf;
 		iov.iov_len = len;
 		/* FIXME: add code to kill session */
-		if (cifs_verify_signature(&iov, 1, server,
-					  mid->sequence_number + 1) != 0)
-			cERROR(1, "Unexpected SMB signature");
+		rc = cifs_verify_signature(&iov, 1, server,
+					   mid->sequence_number + 1);
+		if (rc)
+			cERROR(1, "SMB signature verification returned error = "
+			       "%d", rc);
 	}
 
 	/* BB special case reconnect tid and uid here? */
diff --git a/fs/direct-io.c b/fs/direct-io.c
index 1faf4cb..f86c720 100644
--- a/fs/direct-io.c
+++ b/fs/direct-io.c
@@ -1062,6 +1062,7 @@
 	unsigned long user_addr;
 	size_t bytes;
 	struct buffer_head map_bh = { 0, };
+	struct blk_plug plug;
 
 	if (rw & WRITE)
 		rw = WRITE_ODIRECT;
@@ -1177,6 +1178,8 @@
 				PAGE_SIZE - user_addr / PAGE_SIZE);
 	}
 
+	blk_start_plug(&plug);
+
 	for (seg = 0; seg < nr_segs; seg++) {
 		user_addr = (unsigned long)iov[seg].iov_base;
 		sdio.size += bytes = iov[seg].iov_len;
@@ -1235,6 +1238,8 @@
 	if (sdio.bio)
 		dio_bio_submit(dio, &sdio);
 
+	blk_finish_plug(&plug);
+
 	/*
 	 * It is possible that, we return short IO due to end of file.
 	 * In that case, we need to release all the pages we got hold on.
diff --git a/fs/jbd/journal.c b/fs/jbd/journal.c
index 0935750..a286233 100644
--- a/fs/jbd/journal.c
+++ b/fs/jbd/journal.c
@@ -1113,6 +1113,11 @@
 
 	BUG_ON(!mutex_is_locked(&journal->j_checkpoint_mutex));
 	spin_lock(&journal->j_state_lock);
+	/* Is it already empty? */
+	if (sb->s_start == 0) {
+		spin_unlock(&journal->j_state_lock);
+		return;
+	}
 	jbd_debug(1, "JBD: Marking journal as empty (seq %d)\n",
         	  journal->j_tail_sequence);
 
diff --git a/fs/logfs/dev_bdev.c b/fs/logfs/dev_bdev.c
index df0de27..e784a21 100644
--- a/fs/logfs/dev_bdev.c
+++ b/fs/logfs/dev_bdev.c
@@ -26,6 +26,7 @@
 	struct completion complete;
 
 	bio_init(&bio);
+	bio.bi_max_vecs = 1;
 	bio.bi_io_vec = &bio_vec;
 	bio_vec.bv_page = page;
 	bio_vec.bv_len = PAGE_SIZE;
@@ -95,12 +96,11 @@
 	struct address_space *mapping = super->s_mapping_inode->i_mapping;
 	struct bio *bio;
 	struct page *page;
-	struct request_queue *q = bdev_get_queue(sb->s_bdev);
-	unsigned int max_pages = queue_max_hw_sectors(q) >> (PAGE_SHIFT - 9);
+	unsigned int max_pages;
 	int i;
 
-	if (max_pages > BIO_MAX_PAGES)
-		max_pages = BIO_MAX_PAGES;
+	max_pages = min(nr_pages, (size_t) bio_get_nr_vecs(super->s_bdev));
+
 	bio = bio_alloc(GFP_NOFS, max_pages);
 	BUG_ON(!bio);
 
@@ -190,12 +190,11 @@
 {
 	struct logfs_super *super = logfs_super(sb);
 	struct bio *bio;
-	struct request_queue *q = bdev_get_queue(sb->s_bdev);
-	unsigned int max_pages = queue_max_hw_sectors(q) >> (PAGE_SHIFT - 9);
+	unsigned int max_pages;
 	int i;
 
-	if (max_pages > BIO_MAX_PAGES)
-		max_pages = BIO_MAX_PAGES;
+	max_pages = min(nr_pages, (size_t) bio_get_nr_vecs(super->s_bdev));
+
 	bio = bio_alloc(GFP_NOFS, max_pages);
 	BUG_ON(!bio);
 
diff --git a/fs/logfs/inode.c b/fs/logfs/inode.c
index a422f42..6984562 100644
--- a/fs/logfs/inode.c
+++ b/fs/logfs/inode.c
@@ -156,10 +156,26 @@
 	call_rcu(&inode->i_rcu, logfs_i_callback);
 }
 
+static void __logfs_destroy_meta_inode(struct inode *inode)
+{
+	struct logfs_inode *li = logfs_inode(inode);
+	BUG_ON(li->li_block);
+	call_rcu(&inode->i_rcu, logfs_i_callback);
+}
+
 static void logfs_destroy_inode(struct inode *inode)
 {
 	struct logfs_inode *li = logfs_inode(inode);
 
+	if (inode->i_ino < LOGFS_RESERVED_INOS) {
+		/*
+		 * The reserved inodes are never destroyed unless we are in
+		 * unmont path.
+		 */
+		__logfs_destroy_meta_inode(inode);
+		return;
+	}
+
 	BUG_ON(list_empty(&li->li_freeing_list));
 	spin_lock(&logfs_inode_lock);
 	li->li_refcount--;
@@ -373,8 +389,8 @@
 {
 	struct logfs_super *super = logfs_super(sb);
 	/* kill the meta-inodes */
-	iput(super->s_master_inode);
 	iput(super->s_segfile_inode);
+	iput(super->s_master_inode);
 	iput(super->s_mapping_inode);
 }
 
diff --git a/fs/logfs/journal.c b/fs/logfs/journal.c
index 1e1c369..2a09b8d 100644
--- a/fs/logfs/journal.c
+++ b/fs/logfs/journal.c
@@ -565,7 +565,7 @@
 	index = ofs >> PAGE_SHIFT;
 	page_ofs = ofs & (PAGE_SIZE - 1);
 
-	page = find_lock_page(mapping, index);
+	page = find_or_create_page(mapping, index, GFP_NOFS);
 	BUG_ON(!page);
 	memcpy(wbuf, page_address(page) + page_ofs, super->s_writesize);
 	unlock_page(page);
diff --git a/fs/logfs/readwrite.c b/fs/logfs/readwrite.c
index f1cb512..5be0abe 100644
--- a/fs/logfs/readwrite.c
+++ b/fs/logfs/readwrite.c
@@ -2189,7 +2189,6 @@
 		return;
 	}
 
-	BUG_ON(inode->i_ino < LOGFS_RESERVED_INOS);
 	page = inode_to_page(inode);
 	BUG_ON(!page); /* FIXME: Use emergency page */
 	logfs_put_write_page(page);
diff --git a/fs/logfs/segment.c b/fs/logfs/segment.c
index e28d090..038da09 100644
--- a/fs/logfs/segment.c
+++ b/fs/logfs/segment.c
@@ -886,7 +886,7 @@
 
 static void map_invalidatepage(struct page *page, unsigned long l)
 {
-	BUG();
+	return;
 }
 
 static int map_releasepage(struct page *page, gfp_t g)
diff --git a/fs/nfsd/nfs4callback.c b/fs/nfsd/nfs4callback.c
index cbaf4f8..4c7bd35 100644
--- a/fs/nfsd/nfs4callback.c
+++ b/fs/nfsd/nfs4callback.c
@@ -651,12 +651,12 @@
 
 	if (clp->cl_minorversion == 0) {
 		if (!clp->cl_cred.cr_principal &&
-				(clp->cl_flavor >= RPC_AUTH_GSS_KRB5))
+				(clp->cl_cred.cr_flavor >= RPC_AUTH_GSS_KRB5))
 			return -EINVAL;
 		args.client_name = clp->cl_cred.cr_principal;
 		args.prognumber	= conn->cb_prog,
 		args.protocol = XPRT_TRANSPORT_TCP;
-		args.authflavor = clp->cl_flavor;
+		args.authflavor = clp->cl_cred.cr_flavor;
 		clp->cl_cb_ident = conn->cb_ident;
 	} else {
 		if (!conn->cb_xprt)
diff --git a/fs/nfsd/state.h b/fs/nfsd/state.h
index e617314..22bd0a6 100644
--- a/fs/nfsd/state.h
+++ b/fs/nfsd/state.h
@@ -231,7 +231,6 @@
 	nfs4_verifier		cl_verifier; 	/* generated by client */
 	time_t                  cl_time;        /* time of last lease renewal */
 	struct sockaddr_storage	cl_addr; 	/* client ipaddress */
-	u32			cl_flavor;	/* setclientid pseudoflavor */
 	struct svc_cred		cl_cred; 	/* setclientid principal */
 	clientid_t		cl_clientid;	/* generated by server */
 	nfs4_verifier		cl_confirm;	/* generated by server */
diff --git a/fs/quota/dquot.c b/fs/quota/dquot.c
index 36a29b7..c495a30 100644
--- a/fs/quota/dquot.c
+++ b/fs/quota/dquot.c
@@ -1589,10 +1589,10 @@
 		goto out;
 	}
 
-	down_read(&sb_dqopt(inode->i_sb)->dqptr_sem);
 	for (cnt = 0; cnt < MAXQUOTAS; cnt++)
 		warn[cnt].w_type = QUOTA_NL_NOWARN;
 
+	down_read(&sb_dqopt(inode->i_sb)->dqptr_sem);
 	spin_lock(&dq_data_lock);
 	for (cnt = 0; cnt < MAXQUOTAS; cnt++) {
 		if (!dquots[cnt])
diff --git a/fs/reiserfs/bitmap.c b/fs/reiserfs/bitmap.c
index 4c0c7d1..a98b774 100644
--- a/fs/reiserfs/bitmap.c
+++ b/fs/reiserfs/bitmap.c
@@ -1334,9 +1334,7 @@
 	else if (bitmap == 0)
 		block = (REISERFS_DISK_OFFSET_IN_BYTES >> sb->s_blocksize_bits) + 1;
 
-	reiserfs_write_unlock(sb);
 	bh = sb_bread(sb, block);
-	reiserfs_write_lock(sb);
 	if (bh == NULL)
 		reiserfs_warning(sb, "sh-2029: %s: bitmap block (#%u) "
 		                 "reading failed", __func__, block);
diff --git a/fs/reiserfs/inode.c b/fs/reiserfs/inode.c
index a6d4268..855da58 100644
--- a/fs/reiserfs/inode.c
+++ b/fs/reiserfs/inode.c
@@ -76,10 +76,10 @@
 		;
 	}
       out:
+	reiserfs_write_unlock_once(inode->i_sb, depth);
 	clear_inode(inode);	/* note this must go after the journal_end to prevent deadlock */
 	dquot_drop(inode);
 	inode->i_blocks = 0;
-	reiserfs_write_unlock_once(inode->i_sb, depth);
 	return;
 
 no_delete:
diff --git a/fs/ubifs/debug.h b/fs/ubifs/debug.h
index 8b8cc4e..760de72 100644
--- a/fs/ubifs/debug.h
+++ b/fs/ubifs/debug.h
@@ -167,7 +167,7 @@
 #define ubifs_dbg_msg(type, fmt, ...) \
 	pr_debug("UBIFS DBG " type ": " fmt "\n", ##__VA_ARGS__)
 
-#define DBG_KEY_BUF_LEN 32
+#define DBG_KEY_BUF_LEN 48
 #define ubifs_dbg_msg_key(type, key, fmt, ...) do {                            \
 	char __tmp_key_buf[DBG_KEY_BUF_LEN];                                   \
 	pr_debug("UBIFS DBG " type ": " fmt "%s\n", ##__VA_ARGS__,             \
diff --git a/fs/ubifs/lpt.c b/fs/ubifs/lpt.c
index ce33b2b..8640920 100644
--- a/fs/ubifs/lpt.c
+++ b/fs/ubifs/lpt.c
@@ -1749,7 +1749,10 @@
 	return 0;
 
 out_err:
-	ubifs_lpt_free(c, 0);
+	if (wr)
+		ubifs_lpt_free(c, 1);
+	if (rd)
+		ubifs_lpt_free(c, 0);
 	return err;
 }
 
diff --git a/fs/ubifs/recovery.c b/fs/ubifs/recovery.c
index c30d976b..edeec49 100644
--- a/fs/ubifs/recovery.c
+++ b/fs/ubifs/recovery.c
@@ -788,7 +788,7 @@
 
 corrupted_rescan:
 	/* Re-scan the corrupted data with verbose messages */
-	ubifs_err("corruptio %d", ret);
+	ubifs_err("corruption %d", ret);
 	ubifs_scan_a_node(c, buf, len, lnum, offs, 1);
 corrupted:
 	ubifs_scanned_corruption(c, lnum, offs, buf);
diff --git a/fs/ubifs/replay.c b/fs/ubifs/replay.c
index eba46d4..94d78fc 100644
--- a/fs/ubifs/replay.c
+++ b/fs/ubifs/replay.c
@@ -1026,7 +1026,6 @@
 	c->replaying = 1;
 	lnum = c->ltail_lnum = c->lhead_lnum;
 
-	lnum = UBIFS_LOG_LNUM;
 	do {
 		err = replay_log_leb(c, lnum, 0, c->sbuf);
 		if (err == 1)
@@ -1035,7 +1034,7 @@
 		if (err)
 			goto out;
 		lnum = ubifs_next_log_lnum(c, lnum);
-	} while (lnum != UBIFS_LOG_LNUM);
+	} while (lnum != c->ltail_lnum);
 
 	err = replay_buds(c);
 	if (err)
diff --git a/fs/ubifs/super.c b/fs/ubifs/super.c
index c3fa6c5..71a197f 100644
--- a/fs/ubifs/super.c
+++ b/fs/ubifs/super.c
@@ -1157,9 +1157,6 @@
  *
  * This function mounts UBIFS file system. Returns zero in case of success and
  * a negative error code in case of failure.
- *
- * Note, the function does not de-allocate resources it it fails half way
- * through, and the caller has to do this instead.
  */
 static int mount_ubifs(struct ubifs_info *c)
 {
diff --git a/fs/udf/inode.c b/fs/udf/inode.c
index fafaad7..aa23346 100644
--- a/fs/udf/inode.c
+++ b/fs/udf/inode.c
@@ -1124,14 +1124,17 @@
 				if (err)
 					return err;
 				down_write(&iinfo->i_data_sem);
-			} else
+			} else {
 				iinfo->i_lenAlloc = newsize;
+				goto set_size;
+			}
 		}
 		err = udf_extend_file(inode, newsize);
 		if (err) {
 			up_write(&iinfo->i_data_sem);
 			return err;
 		}
+set_size:
 		truncate_setsize(inode, newsize);
 		up_write(&iinfo->i_data_sem);
 	} else {
diff --git a/fs/udf/super.c b/fs/udf/super.c
index dcbf987..18fc038 100644
--- a/fs/udf/super.c
+++ b/fs/udf/super.c
@@ -1344,6 +1344,7 @@
 		udf_err(sb, "error loading logical volume descriptor: "
 			"Partition table too long (%u > %lu)\n", table_len,
 			sb->s_blocksize - sizeof(*lvd));
+		ret = 1;
 		goto out_bh;
 	}
 
@@ -1388,8 +1389,10 @@
 						UDF_ID_SPARABLE,
 						strlen(UDF_ID_SPARABLE))) {
 				if (udf_load_sparable_map(sb, map,
-				    (struct sparablePartitionMap *)gpm) < 0)
+				    (struct sparablePartitionMap *)gpm) < 0) {
+					ret = 1;
 					goto out_bh;
+				}
 			} else if (!strncmp(upm2->partIdent.ident,
 						UDF_ID_METADATA,
 						strlen(UDF_ID_METADATA))) {
@@ -2000,6 +2003,8 @@
 			if (!silent)
 				pr_notice("Rescanning with blocksize %d\n",
 					  UDF_DEFAULT_BLOCKSIZE);
+			brelse(sbi->s_lvid_bh);
+			sbi->s_lvid_bh = NULL;
 			uopt.blocksize = UDF_DEFAULT_BLOCKSIZE;
 			ret = udf_load_vrs(sb, &uopt, silent, &fileset);
 		}
diff --git a/fs/xfs/xfs_discard.c b/fs/xfs/xfs_discard.c
index f9c3fe3..69cf4fc 100644
--- a/fs/xfs/xfs_discard.c
+++ b/fs/xfs/xfs_discard.c
@@ -179,12 +179,14 @@
 	 * used by the fstrim application.  In the end it really doesn't
 	 * matter as trimming blocks is an advisory interface.
 	 */
+	if (range.start >= XFS_FSB_TO_B(mp, mp->m_sb.sb_dblocks) ||
+	    range.minlen > XFS_FSB_TO_B(mp, XFS_ALLOC_AG_MAX_USABLE(mp)))
+		return -XFS_ERROR(EINVAL);
+
 	start = BTOBB(range.start);
 	end = start + BTOBBT(range.len) - 1;
 	minlen = BTOBB(max_t(u64, granularity, range.minlen));
 
-	if (XFS_BB_TO_FSB(mp, start) >= mp->m_sb.sb_dblocks)
-		return -XFS_ERROR(EINVAL);
 	if (end > XFS_FSB_TO_BB(mp, mp->m_sb.sb_dblocks) - 1)
 		end = XFS_FSB_TO_BB(mp, mp->m_sb.sb_dblocks)- 1;
 
diff --git a/fs/xfs/xfs_ialloc.c b/fs/xfs/xfs_ialloc.c
index 21e37b5..5aceb3f 100644
--- a/fs/xfs/xfs_ialloc.c
+++ b/fs/xfs/xfs_ialloc.c
@@ -962,23 +962,22 @@
 		if (!pag->pagi_freecount && !okalloc)
 			goto nextag;
 
+		/*
+		 * Then read in the AGI buffer and recheck with the AGI buffer
+		 * lock held.
+		 */
 		error = xfs_ialloc_read_agi(mp, tp, agno, &agbp);
 		if (error)
 			goto out_error;
 
-		/*
-		 * Once the AGI has been read in we have to recheck
-		 * pagi_freecount with the AGI buffer lock held.
-		 */
 		if (pag->pagi_freecount) {
 			xfs_perag_put(pag);
 			goto out_alloc;
 		}
 
-		if (!okalloc) {
-			xfs_trans_brelse(tp, agbp);
-			goto nextag;
-		}
+		if (!okalloc)
+			goto nextag_relse_buffer;
+
 
 		error = xfs_ialloc_ag_alloc(tp, agbp, &ialloced);
 		if (error) {
@@ -1007,6 +1006,8 @@
 			return 0;
 		}
 
+nextag_relse_buffer:
+		xfs_trans_brelse(tp, agbp);
 nextag:
 		xfs_perag_put(pag);
 		if (++agno == mp->m_sb.sb_agcount)
diff --git a/fs/xfs/xfs_rtalloc.c b/fs/xfs/xfs_rtalloc.c
index 92d4331..ca28a4b 100644
--- a/fs/xfs/xfs_rtalloc.c
+++ b/fs/xfs/xfs_rtalloc.c
@@ -857,7 +857,7 @@
 	xfs_buf_t	*bp;		/* block buffer, result */
 	xfs_inode_t	*ip;		/* bitmap or summary inode */
 	xfs_bmbt_irec_t	map;
-	int		nmap;
+	int		nmap = 1;
 	int		error;		/* error value */
 
 	ip = issum ? mp->m_rsumip : mp->m_rbmip;
diff --git a/include/drm/drm_crtc.h b/include/drm/drm_crtc.h
index ced3625..bfacf0d 100644
--- a/include/drm/drm_crtc.h
+++ b/include/drm/drm_crtc.h
@@ -118,7 +118,8 @@
 	.hdisplay = (hd), .hsync_start = (hss), .hsync_end = (hse), \
 	.htotal = (ht), .hskew = (hsk), .vdisplay = (vd), \
 	.vsync_start = (vss), .vsync_end = (vse), .vtotal = (vt), \
-	.vscan = (vs), .flags = (f), .vrefresh = 0
+	.vscan = (vs), .flags = (f), .vrefresh = 0, \
+	.base.type = DRM_MODE_OBJECT_MODE
 
 #define CRTC_INTERLACE_HALVE_V 0x1 /* halve V values for interlacing */
 
diff --git a/include/drm/drm_mode.h b/include/drm/drm_mode.h
index 5581980..3d6301b 100644
--- a/include/drm/drm_mode.h
+++ b/include/drm/drm_mode.h
@@ -359,8 +359,9 @@
 	struct drm_mode_modeinfo mode;
 };
 
-#define DRM_MODE_CURSOR_BO	(1<<0)
-#define DRM_MODE_CURSOR_MOVE	(1<<1)
+#define DRM_MODE_CURSOR_BO	0x01
+#define DRM_MODE_CURSOR_MOVE	0x02
+#define DRM_MODE_CURSOR_FLAGS	0x03
 
 /*
  * depending on the value in flags different members are used.
diff --git a/include/linux/Kbuild b/include/linux/Kbuild
index fa21760..c57e064 100644
--- a/include/linux/Kbuild
+++ b/include/linux/Kbuild
@@ -84,7 +84,6 @@
 header-y += capi.h
 header-y += cciss_defs.h
 header-y += cciss_ioctl.h
-header-y += cdk.h
 header-y += cdrom.h
 header-y += cgroupstats.h
 header-y += chio.h
@@ -93,7 +92,6 @@
 header-y += coda.h
 header-y += coda_psdev.h
 header-y += coff.h
-header-y += comstats.h
 header-y += connector.h
 header-y += const.h
 header-y += cramfs_fs.h
@@ -140,7 +138,6 @@
 header-y += futex.h
 header-y += gameport.h
 header-y += gen_stats.h
-header-y += generic_serial.h
 header-y += genetlink.h
 header-y += gfs2_ondisk.h
 header-y += gigaset_dev.h
@@ -372,6 +369,7 @@
 header-y += tipc_config.h
 header-y += toshiba.h
 header-y += tty.h
+header-y += tty_flags.h
 header-y += types.h
 header-y += udf_fs_i.h
 header-y += udp.h
diff --git a/include/linux/amba/serial.h b/include/linux/amba/serial.h
index d117b29..f612c78 100644
--- a/include/linux/amba/serial.h
+++ b/include/linux/amba/serial.h
@@ -205,7 +205,6 @@
 	void *dma_tx_param;
         void (*init) (void);
 	void (*exit) (void);
-	void (*reset) (void);
 };
 #endif
 
diff --git a/include/linux/blkdev.h b/include/linux/blkdev.h
index 4e72a9d..4a2ab7c 100644
--- a/include/linux/blkdev.h
+++ b/include/linux/blkdev.h
@@ -601,7 +601,7 @@
  * it already be started by driver.
  */
 #define RQ_NOMERGE_FLAGS	\
-	(REQ_NOMERGE | REQ_STARTED | REQ_SOFTBARRIER | REQ_FLUSH | REQ_FUA)
+	(REQ_NOMERGE | REQ_STARTED | REQ_SOFTBARRIER | REQ_FLUSH | REQ_FUA | REQ_DISCARD)
 #define rq_mergeable(rq)	\
 	(!((rq)->cmd_flags & RQ_NOMERGE_FLAGS) && \
 	 (((rq)->cmd_flags & REQ_DISCARD) || \
@@ -894,6 +894,8 @@
 extern struct backing_dev_info *blk_get_backing_dev_info(struct block_device *bdev);
 
 extern int blk_rq_map_sg(struct request_queue *, struct request *, struct scatterlist *);
+extern int blk_bio_map_sg(struct request_queue *q, struct bio *bio,
+			  struct scatterlist *sglist);
 extern void blk_dump_rq_flags(struct request *, char *);
 extern long nr_blockdev_pages(void);
 
@@ -1139,6 +1141,16 @@
 		& (lim->discard_granularity - 1);
 }
 
+static inline int bdev_discard_alignment(struct block_device *bdev)
+{
+	struct request_queue *q = bdev_get_queue(bdev);
+
+	if (bdev != bdev->bd_contains)
+		return bdev->bd_part->discard_alignment;
+
+	return q->limits.discard_alignment;
+}
+
 static inline unsigned int queue_discard_zeroes_data(struct request_queue *q)
 {
 	if (q->limits.max_discard_sectors && q->limits.discard_zeroes_data == 1)
diff --git a/include/linux/cd1400.h b/include/linux/cd1400.h
deleted file mode 100644
index 1dc3ab0..0000000
--- a/include/linux/cd1400.h
+++ /dev/null
@@ -1,292 +0,0 @@
-/*****************************************************************************/
-
-/*
- *	cd1400.h  -- cd1400 UART hardware info.
- *
- *	Copyright (C) 1996-1998  Stallion Technologies
- *	Copyright (C) 1994-1996  Greg Ungerer.
- *
- *	This program is free software; you can redistribute it and/or modify
- *	it under the terms of the GNU General Public License as published by
- *	the Free Software Foundation; either version 2 of the License, or
- *	(at your option) any later version.
- *
- *	This program is distributed in the hope that it will be useful,
- *	but WITHOUT ANY WARRANTY; without even the implied warranty of
- *	MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *	GNU General Public License for more details.
- *
- *	You should have received a copy of the GNU General Public License
- *	along with this program; if not, write to the Free Software
- *	Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-/*****************************************************************************/
-#ifndef	_CD1400_H
-#define	_CD1400_H
-/*****************************************************************************/
-
-/*
- *	Define the number of async ports per cd1400 uart chip.
- */
-#define	CD1400_PORTS		4
-
-/*
- *	Define the cd1400 uarts internal FIFO sizes.
- */
-#define	CD1400_TXFIFOSIZE	12
-#define	CD1400_RXFIFOSIZE	12
-
-/*
- *	Local RX FIFO thresh hold level. Also define the RTS thresh hold
- *	based on the RX thresh hold.
- */
-#define	FIFO_RXTHRESHOLD	6
-#define	FIFO_RTSTHRESHOLD	7
-
-/*****************************************************************************/
-
-/*
- *	Define the cd1400 register addresses. These are all the valid
- *	registers with the cd1400. Some are global, some virtual, some
- *	per port.
- */
-#define	GFRCR		0x40
-#define	CAR		0x68
-#define	GCR		0x4b
-#define	SVRR		0x67
-#define	RICR		0x44
-#define	TICR		0x45
-#define	MICR		0x46
-#define	RIR		0x6b
-#define	TIR		0x6a
-#define	MIR		0x69
-#define	PPR		0x7e
-
-#define	RIVR		0x43
-#define	TIVR		0x42
-#define	MIVR		0x41
-#define	TDR		0x63
-#define	RDSR		0x62
-#define	MISR		0x4c
-#define	EOSRR		0x60
-
-#define	LIVR		0x18
-#define	CCR		0x05
-#define	SRER		0x06
-#define	COR1		0x08
-#define	COR2		0x09
-#define	COR3		0x0a
-#define	COR4		0x1e
-#define	COR5		0x1f
-#define	CCSR		0x0b
-#define	RDCR		0x0e
-#define	SCHR1		0x1a
-#define	SCHR2		0x1b
-#define	SCHR3		0x1c
-#define	SCHR4		0x1d
-#define	SCRL		0x22
-#define	SCRH		0x23
-#define	LNC		0x24
-#define	MCOR1		0x15
-#define	MCOR2		0x16
-#define	RTPR		0x21
-#define	MSVR1		0x6c
-#define	MSVR2		0x6d
-#define	PSVR		0x6f
-#define	RBPR		0x78
-#define	RCOR		0x7c
-#define	TBPR		0x72
-#define	TCOR		0x76
-
-/*****************************************************************************/
-
-/*
- *	Define the set of baud rate clock divisors.
- */
-#define	CD1400_CLK0	8
-#define	CD1400_CLK1	32
-#define	CD1400_CLK2	128
-#define	CD1400_CLK3	512
-#define	CD1400_CLK4	2048
-
-#define	CD1400_NUMCLKS	5
-
-/*****************************************************************************/
-
-/*
- *	Define the clock pre-scalar value to be a 5 ms clock. This should be
- *	OK for now. It would probably be better to make it 10 ms, but we
- *	can't fit that divisor into 8 bits!
- */
-#define	PPR_SCALAR	244
-
-/*****************************************************************************/
-
-/*
- *	Define values used to set character size options.
- */
-#define	COR1_CHL5	0x00
-#define	COR1_CHL6	0x01
-#define	COR1_CHL7	0x02
-#define	COR1_CHL8	0x03
-
-/*
- *	Define values used to set the number of stop bits.
- */
-#define	COR1_STOP1	0x00
-#define	COR1_STOP15	0x04
-#define	COR1_STOP2	0x08
-
-/*
- *	Define values used to set the parity scheme in use.
- */
-#define	COR1_PARNONE	0x00
-#define	COR1_PARFORCE	0x20
-#define	COR1_PARENB	0x40
-#define	COR1_PARIGNORE	0x10
-
-#define	COR1_PARODD	0x80
-#define	COR1_PAREVEN	0x00
-
-#define	COR2_IXM	0x80
-#define	COR2_TXIBE	0x40
-#define	COR2_ETC	0x20
-#define	COR2_LLM	0x10
-#define	COR2_RLM	0x08
-#define	COR2_RTSAO	0x04
-#define	COR2_CTSAE	0x02
-
-#define	COR3_SCDRNG	0x80
-#define	COR3_SCD34	0x40
-#define	COR3_FCT	0x20
-#define	COR3_SCD12	0x10
-
-/*
- *	Define values used by COR4.
- */
-#define	COR4_BRKINT	0x08
-#define	COR4_IGNBRK	0x18
-
-/*****************************************************************************/
-
-/*
- *	Define the modem control register values.
- *	Note that the actual hardware is a little different to the conventional
- *	pin names on the cd1400.
- */
-#define	MSVR1_DTR	0x01
-#define	MSVR1_DSR	0x10
-#define	MSVR1_RI	0x20
-#define	MSVR1_CTS	0x40
-#define	MSVR1_DCD	0x80
-
-#define	MSVR2_RTS	0x02
-#define	MSVR2_DSR	0x10
-#define	MSVR2_RI	0x20
-#define	MSVR2_CTS	0x40
-#define	MSVR2_DCD	0x80
-
-#define	MCOR1_DCD	0x80
-#define	MCOR1_CTS	0x40
-#define	MCOR1_RI	0x20
-#define	MCOR1_DSR	0x10
-
-#define	MCOR2_DCD	0x80
-#define	MCOR2_CTS	0x40
-#define	MCOR2_RI	0x20
-#define	MCOR2_DSR	0x10
-
-/*****************************************************************************/
-
-/*
- *	Define the bits used with the service (interrupt) enable register.
- */
-#define	SRER_NNDT	0x01
-#define	SRER_TXEMPTY	0x02
-#define	SRER_TXDATA	0x04
-#define	SRER_RXDATA	0x10
-#define	SRER_MODEM	0x80
-
-/*****************************************************************************/
-
-/*
- *	Define operational commands for the command register.
- */
-#define	CCR_RESET	0x80
-#define	CCR_CORCHANGE	0x4e
-#define	CCR_SENDCH	0x20
-#define	CCR_CHANCTRL	0x10
-
-#define	CCR_TXENABLE	(CCR_CHANCTRL | 0x08)
-#define	CCR_TXDISABLE	(CCR_CHANCTRL | 0x04)
-#define	CCR_RXENABLE	(CCR_CHANCTRL | 0x02)
-#define	CCR_RXDISABLE	(CCR_CHANCTRL | 0x01)
-
-#define	CCR_SENDSCHR1	(CCR_SENDCH | 0x01)
-#define	CCR_SENDSCHR2	(CCR_SENDCH | 0x02)
-#define	CCR_SENDSCHR3	(CCR_SENDCH | 0x03)
-#define	CCR_SENDSCHR4	(CCR_SENDCH | 0x04)
-
-#define	CCR_RESETCHAN	(CCR_RESET | 0x00)
-#define	CCR_RESETFULL	(CCR_RESET | 0x01)
-#define	CCR_TXFLUSHFIFO	(CCR_RESET | 0x02)
-
-#define	CCR_MAXWAIT	10000
-
-/*****************************************************************************/
-
-/*
- *	Define the valid acknowledgement types (for hw ack cycle).
- */
-#define	ACK_TYPMASK	0x07
-#define	ACK_TYPTX	0x02
-#define	ACK_TYPMDM	0x01
-#define	ACK_TYPRXGOOD	0x03
-#define	ACK_TYPRXBAD	0x07
-
-#define	SVRR_RX		0x01
-#define	SVRR_TX		0x02
-#define	SVRR_MDM	0x04
-
-#define	ST_OVERRUN	0x01
-#define	ST_FRAMING	0x02
-#define	ST_PARITY	0x04
-#define	ST_BREAK	0x08
-#define	ST_SCHAR1	0x10
-#define	ST_SCHAR2	0x20
-#define	ST_SCHAR3	0x30
-#define	ST_SCHAR4	0x40
-#define	ST_RANGE	0x70
-#define	ST_SCHARMASK	0x70
-#define	ST_TIMEOUT	0x80
-
-#define	MISR_DCD	0x80
-#define	MISR_CTS	0x40
-#define	MISR_RI		0x20
-#define	MISR_DSR	0x10
-
-/*****************************************************************************/
-
-/*
- *	Defines for the CCSR status register.
- */
-#define	CCSR_RXENABLED	0x80
-#define	CCSR_RXFLOWON	0x40
-#define	CCSR_RXFLOWOFF	0x20
-#define	CCSR_TXENABLED	0x08
-#define	CCSR_TXFLOWON	0x04
-#define	CCSR_TXFLOWOFF	0x02
-
-/*****************************************************************************/
-
-/*
- *	Define the embedded commands.
- */
-#define	ETC_CMD		0x00
-#define	ETC_STARTBREAK	0x81
-#define	ETC_DELAY	0x82
-#define	ETC_STOPBREAK	0x83
-
-/*****************************************************************************/
-#endif
diff --git a/include/linux/cdk.h b/include/linux/cdk.h
deleted file mode 100644
index 80093a8..0000000
--- a/include/linux/cdk.h
+++ /dev/null
@@ -1,486 +0,0 @@
-/*****************************************************************************/
-
-/*
- *	cdk.h  -- CDK interface definitions.
- *
- *	Copyright (C) 1996-1998  Stallion Technologies
- *	Copyright (C) 1994-1996  Greg Ungerer.
- *
- *	This program is free software; you can redistribute it and/or modify
- *	it under the terms of the GNU General Public License as published by
- *	the Free Software Foundation; either version 2 of the License, or
- *	(at your option) any later version.
- *
- *	This program is distributed in the hope that it will be useful,
- *	but WITHOUT ANY WARRANTY; without even the implied warranty of
- *	MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *	GNU General Public License for more details.
- *
- *	You should have received a copy of the GNU General Public License
- *	along with this program; if not, write to the Free Software
- *	Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-/*****************************************************************************/
-#ifndef	_CDK_H
-#define	_CDK_H
-/*****************************************************************************/
-
-#pragma	pack(2)
-
-/*
- *	The following set of definitions is used to communicate with the
- *	shared memory interface of the Stallion intelligent multiport serial
- *	boards. The definitions in this file are taken directly from the
- *	document titled "Generic Stackable Interface, Downloader and
- *	Communications Development Kit".
- */
-
-/*
- *	Define the set of important shared memory addresses. These are
- *	required to initialize the board and get things started. All of these
- *	addresses are relative to the start of the shared memory.
- */
-#define	CDK_SIGADDR	0x200
-#define	CDK_FEATADDR	0x280
-#define	CDK_CDKADDR	0x300
-#define	CDK_RDYADDR	0x262
-
-#define	CDK_ALIVEMARKER	13
-
-/*
- *	On hardware power up the ROMs located on the EasyConnection 8/64 will
- *	fill out the following signature information into shared memory. This
- *	way the host system can quickly determine that the board is present
- *	and is operational.
- */
-typedef struct cdkecpsig {
-	unsigned long	magic;
-	unsigned short	romver;
-	unsigned short	cputype;
-	unsigned char	panelid[8];
-} cdkecpsig_t;
-
-#define	ECP_MAGIC	0x21504345
-
-/*
- *	On hardware power up the ROMs located on the ONboard, Stallion and
- *	Brumbys will fill out the following signature information into shared
- *	memory. This way the host system can quickly determine that the board
- *	is present and is operational.
- */
-typedef struct cdkonbsig {
-	unsigned short	magic0;
-	unsigned short	magic1;
-	unsigned short	magic2;
-	unsigned short	magic3;
-	unsigned short	romver;
-	unsigned short	memoff;
-	unsigned short	memseg;
-	unsigned short	amask0;
-	unsigned short	pic;
-	unsigned short	status;
-	unsigned short	btype;
-	unsigned short	clkticks;
-	unsigned short	clkspeed;
-	unsigned short	amask1;
-	unsigned short	amask2;
-} cdkonbsig_t;
-
-#define	ONB_MAGIC0	0xf2a7
-#define	ONB_MAGIC1	0xa149
-#define	ONB_MAGIC2	0x6352
-#define	ONB_MAGIC3	0xf121
-
-/*
- *	Define the feature area structure. The feature area is the set of
- *	startup parameters used by the slave image when it starts executing.
- *	They allow for the specification of buffer sizes, debug trace, etc.
- */
-typedef struct cdkfeature {
-	unsigned long	debug;
-	unsigned long	banner;
-	unsigned long	etype;
-	unsigned long	nrdevs;
-	unsigned long	brdspec;
-	unsigned long	txrqsize;
-	unsigned long	rxrqsize;
-	unsigned long	flags;
-} cdkfeature_t;
-
-#define	ETYP_DDK	0
-#define	ETYP_CDK	1
-
-/*
- *	Define the CDK header structure. This is the info that the slave
- *	environment sets up after it has been downloaded and started. It
- *	essentially provides a memory map for the shared memory interface.
- */
-typedef struct cdkhdr {
-	unsigned short	command;
-	unsigned short	status;
-	unsigned short	port;
-	unsigned short	mode;
-	unsigned long	cmd_buf[14];
-	unsigned short	alive_cnt;
-	unsigned short	intrpt_mode;
-	unsigned char	intrpt_id[8];
-	unsigned char	ver_release;
-	unsigned char	ver_modification;
-	unsigned char	ver_fix;
-	unsigned char	deadman_restart;
-	unsigned short	deadman;
-	unsigned short	nrdevs;
-	unsigned long	memp;
-	unsigned long	hostp;
-	unsigned long	slavep;
-	unsigned char	hostreq;
-	unsigned char	slavereq;
-	unsigned char	cmd_reserved[30];
-} cdkhdr_t;
-
-#define	MODE_DDK	0
-#define	MODE_CDK	1
-
-#define	IMD_INTR	0x0
-#define	IMD_PPINTR	0x1
-#define	IMD_POLL	0xff
-
-/*
- *	Define the memory mapping structure. This structure is pointed to by
- *	the memp field in the stlcdkhdr struct. As many as these structures
- *	as required are laid out in shared memory to define how the rest of
- *	shared memory is divided up. There will be one for each port.
- */
-typedef struct cdkmem {
-	unsigned short	dtype;
-	unsigned long	offset;
-} cdkmem_t;
-
-#define	TYP_UNDEFINED	0x0
-#define	TYP_ASYNCTRL	0x1
-#define	TYP_ASYNC	0x20
-#define	TYP_PARALLEL	0x40
-#define	TYP_SYNCX21	0x60
-
-/*****************************************************************************/
-
-/*
- *	Following is a set of defines and structures used to actually deal
- *	with the serial ports on the board. Firstly is the set of commands
- *	that can be applied to ports.
- */
-#define	ASYCMD		(((unsigned long) 'a') << 8)
-
-#define	A_NULL		(ASYCMD | 0)
-#define	A_FLUSH		(ASYCMD | 1)
-#define	A_BREAK		(ASYCMD | 2)
-#define	A_GETPORT	(ASYCMD | 3)
-#define	A_SETPORT	(ASYCMD | 4)
-#define	A_SETPORTF	(ASYCMD | 5)
-#define	A_SETPORTFTX	(ASYCMD | 6)
-#define	A_SETPORTFRX	(ASYCMD | 7)
-#define	A_GETSIGNALS	(ASYCMD | 8)
-#define	A_SETSIGNALS	(ASYCMD | 9)
-#define	A_SETSIGNALSF	(ASYCMD | 10)
-#define	A_SETSIGNALSFTX	(ASYCMD | 11)
-#define	A_SETSIGNALSFRX	(ASYCMD | 12)
-#define	A_GETNOTIFY	(ASYCMD | 13)
-#define	A_SETNOTIFY	(ASYCMD | 14)
-#define	A_NOTIFY	(ASYCMD | 15)
-#define	A_PORTCTRL	(ASYCMD | 16)
-#define	A_GETSTATS	(ASYCMD | 17)
-#define	A_RQSTATE	(ASYCMD | 18)
-#define	A_FLOWSTATE	(ASYCMD | 19)
-#define	A_CLEARSTATS	(ASYCMD | 20)
-
-/*
- *	Define those arguments used for simple commands.
- */
-#define	FLUSHRX		0x1
-#define	FLUSHTX		0x2
-
-#define	BREAKON		-1
-#define	BREAKOFF	-2
-
-/*
- *	Define the port setting structure, and all those defines that go along
- *	with it. Basically this structure defines the characteristics of this
- *	port: baud rate, chars, parity, input/output char cooking etc.
- */
-typedef struct asyport {
-	unsigned long	baudout;
-	unsigned long	baudin;
-	unsigned long	iflag;
-	unsigned long	oflag;
-	unsigned long	lflag;
-	unsigned long	pflag;
-	unsigned long	flow;
-	unsigned long	spare1;
-	unsigned short	vtime;
-	unsigned short	vmin;
-	unsigned short	txlo;
-	unsigned short	txhi;
-	unsigned short	rxlo;
-	unsigned short	rxhi;
-	unsigned short	rxhog;
-	unsigned short	spare2;
-	unsigned char	csize;
-	unsigned char	stopbs;
-	unsigned char	parity;
-	unsigned char	stopin;
-	unsigned char	startin;
-	unsigned char	stopout;
-	unsigned char	startout;
-	unsigned char	parmark;
-	unsigned char	brkmark;
-	unsigned char	cc[11];
-} asyport_t;
-
-#define	PT_STOP1	0x0
-#define	PT_STOP15	0x1
-#define	PT_STOP2	0x2
-
-#define	PT_NOPARITY	0x0
-#define	PT_ODDPARITY	0x1
-#define	PT_EVENPARITY	0x2
-#define	PT_MARKPARITY	0x3
-#define	PT_SPACEPARITY	0x4
-
-#define	F_NONE		0x0
-#define	F_IXON		0x1
-#define	F_IXOFF		0x2
-#define	F_IXANY		0x4
-#define	F_IOXANY	0x8
-#define	F_RTSFLOW	0x10
-#define	F_CTSFLOW	0x20
-#define	F_DTRFLOW	0x40
-#define	F_DCDFLOW	0x80
-#define	F_DSROFLOW	0x100
-#define	F_DSRIFLOW	0x200
-
-#define	FI_NORX		0x1
-#define	FI_RAW		0x2
-#define	FI_ISTRIP	0x4
-#define	FI_UCLC		0x8
-#define	FI_INLCR	0x10
-#define	FI_ICRNL	0x20
-#define	FI_IGNCR	0x40
-#define	FI_IGNBREAK	0x80
-#define	FI_DSCRDBREAK	0x100
-#define	FI_1MARKBREAK	0x200
-#define	FI_2MARKBREAK	0x400
-#define	FI_XCHNGBREAK	0x800
-#define	FI_IGNRXERRS	0x1000
-#define	FI_DSCDRXERRS	0x2000
-#define	FI_1MARKRXERRS	0x4000
-#define	FI_2MARKRXERRS	0x8000
-#define	FI_XCHNGRXERRS	0x10000
-#define	FI_DSCRDNULL	0x20000
-
-#define	FO_OLCUC	0x1
-#define	FO_ONLCR	0x2
-#define	FO_OOCRNL	0x4
-#define	FO_ONOCR	0x8
-#define	FO_ONLRET	0x10
-#define	FO_ONL		0x20
-#define	FO_OBS		0x40
-#define	FO_OVT		0x80
-#define	FO_OFF		0x100
-#define	FO_OTAB1	0x200
-#define	FO_OTAB2	0x400
-#define	FO_OTAB3	0x800
-#define	FO_OCR1		0x1000
-#define	FO_OCR2		0x2000
-#define	FO_OCR3		0x4000
-#define	FO_OFILL	0x8000
-#define	FO_ODELL	0x10000
-
-#define	P_RTSLOCK	0x1
-#define	P_CTSLOCK	0x2
-#define	P_MAPRTS	0x4
-#define	P_MAPCTS	0x8
-#define	P_LOOPBACK	0x10
-#define	P_DTRFOLLOW	0x20
-#define	P_FAKEDCD	0x40
-
-#define	P_RXIMIN	0x10000
-#define	P_RXITIME	0x20000
-#define	P_RXTHOLD	0x40000
-
-/*
- *	Define a structure to communicate serial port signal and data state
- *	information.
- */
-typedef struct asysigs {
-	unsigned long	data;
-	unsigned long	signal;
-	unsigned long	sigvalue;
-} asysigs_t;
-
-#define	DT_TXBUSY	0x1
-#define	DT_TXEMPTY	0x2
-#define	DT_TXLOW	0x4
-#define	DT_TXHIGH	0x8
-#define	DT_TXFULL	0x10
-#define	DT_TXHOG	0x20
-#define	DT_TXFLOWED	0x40
-#define	DT_TXBREAK	0x80
-
-#define	DT_RXBUSY	0x100
-#define	DT_RXEMPTY	0x200
-#define	DT_RXLOW	0x400
-#define	DT_RXHIGH	0x800
-#define	DT_RXFULL	0x1000
-#define	DT_RXHOG	0x2000
-#define	DT_RXFLOWED	0x4000
-#define	DT_RXBREAK	0x8000
-
-#define	SG_DTR		0x1
-#define	SG_DCD		0x2
-#define	SG_RTS		0x4
-#define	SG_CTS		0x8
-#define	SG_DSR		0x10
-#define	SG_RI		0x20
-
-/*
- *	Define the notification setting structure. This is used to tell the
- *	port what events we want to be informed about. Fields here use the
- *	same defines as for the asysigs structure above.
- */
-typedef struct asynotify {
-	unsigned long	ctrl;
-	unsigned long	data;
-	unsigned long	signal;
-	unsigned long	sigvalue;
-} asynotify_t;
-
-/*
- *	Define the port control structure. It is used to do fine grain
- *	control operations on the port.
- */
-typedef struct {
-	unsigned long	rxctrl;
-	unsigned long	txctrl;
-	char		rximdch;
-	char		tximdch;
-	char		spare1;
-	char		spare2;
-} asyctrl_t;
-
-#define	CT_ENABLE	0x1
-#define	CT_DISABLE	0x2
-#define	CT_STOP		0x4
-#define	CT_START	0x8
-#define	CT_STARTFLOW	0x10
-#define	CT_STOPFLOW	0x20
-#define	CT_SENDCHR	0x40
-
-/*
- *	Define the stats structure kept for each port. This is a useful set
- *	of data collected for each port on the slave. The A_GETSTATS command
- *	is used to retrieve this data from the slave.
- */
-typedef struct asystats {
-	unsigned long	opens;
-	unsigned long	txchars;
-	unsigned long	rxchars;
-	unsigned long	txringq;
-	unsigned long	rxringq;
-	unsigned long	txmsgs;
-	unsigned long	rxmsgs;
-	unsigned long	txflushes;
-	unsigned long	rxflushes;
-	unsigned long	overruns;
-	unsigned long	framing;
-	unsigned long	parity;
-	unsigned long	ringover;
-	unsigned long	lost;
-	unsigned long	rxstart;
-	unsigned long	rxstop;
-	unsigned long	txstart;
-	unsigned long	txstop;
-	unsigned long	dcdcnt;
-	unsigned long	dtrcnt;
-	unsigned long	ctscnt;
-	unsigned long	rtscnt;
-	unsigned long	dsrcnt;
-	unsigned long	ricnt;
-	unsigned long	txbreaks;
-	unsigned long	rxbreaks;
-	unsigned long	signals;
-	unsigned long	state;
-	unsigned long	hwid;
-} asystats_t;
-
-/*****************************************************************************/
-
-/*
- *	All command and control communication with a device on the slave is
- *	via a control block in shared memory. Each device has its own control
- *	block, defined by the following structure. The control block allows
- *	the host to open, close and control the device on the slave.
- */
-typedef struct cdkctrl {
-	unsigned char	open;
-	unsigned char	close;
-	unsigned long	openarg;
-	unsigned long	closearg;
-	unsigned long	cmd;
-	unsigned long	status;
-	unsigned long	args[32];
-} cdkctrl_t;
-
-/*
- *	Each device on the slave passes data to and from the host via a ring
- *	queue in shared memory. Define a ring queue structure to hold the
- *	vital information about each ring queue. Two ring queues will be
- *	allocated for each port, one for receive data and one for transmit
- *	data.
- */
-typedef struct cdkasyrq {
-	unsigned long	offset;
-	unsigned short	size;
-	unsigned short	head;
-	unsigned short	tail;
-} cdkasyrq_t;
-
-/*
- *	Each asynchronous port is defined in shared memory by the following
- *	structure. It contains a control block to command a device, and also
- *	the necessary data channel information as well.
- */
-typedef struct cdkasy {
-	cdkctrl_t	ctrl;
-	unsigned short	notify;
-	asynotify_t	changed;
-	unsigned short	receive;
-	cdkasyrq_t	rxq;
-	unsigned short	transmit;
-	cdkasyrq_t	txq;
-} cdkasy_t;
-
-#pragma	pack()
-
-/*****************************************************************************/
-
-/*
- *	Define the set of ioctls used by the driver to do special things
- *	to the board. These include interrupting it, and initializing
- *	the driver after board startup and shutdown.
- */
-#include <linux/ioctl.h>
-
-#define	STL_BINTR	_IO('s',20)
-#define	STL_BSTART	_IO('s',21)
-#define	STL_BSTOP	_IO('s',22)
-#define	STL_BRESET	_IO('s',23)
-
-/*
- *	Define a set of ioctl extensions, used to get at special stuff.
- */
-#define	STL_GETPFLAG	_IO('s',80)
-#define	STL_SETPFLAG	_IO('s',81)
-
-/*****************************************************************************/
-#endif
diff --git a/include/linux/comstats.h b/include/linux/comstats.h
deleted file mode 100644
index 3f5ea8e..0000000
--- a/include/linux/comstats.h
+++ /dev/null
@@ -1,119 +0,0 @@
-/*****************************************************************************/
-
-/*
- *	comstats.h  -- Serial Port Stats.
- *
- *	Copyright (C) 1996-1998  Stallion Technologies
- *	Copyright (C) 1994-1996  Greg Ungerer.
- *
- *	This program is free software; you can redistribute it and/or modify
- *	it under the terms of the GNU General Public License as published by
- *	the Free Software Foundation; either version 2 of the License, or
- *	(at your option) any later version.
- *
- *	This program is distributed in the hope that it will be useful,
- *	but WITHOUT ANY WARRANTY; without even the implied warranty of
- *	MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *	GNU General Public License for more details.
- *
- *	You should have received a copy of the GNU General Public License
- *	along with this program; if not, write to the Free Software
- *	Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-/*****************************************************************************/
-#ifndef	_COMSTATS_H
-#define	_COMSTATS_H
-/*****************************************************************************/
-
-/*
- *	Serial port stats structure. The structure itself is UART
- *	independent, but some fields may be UART/driver specific (for
- *	example state).
- */
-
-typedef struct {
-	unsigned long	brd;
-	unsigned long	panel;
-	unsigned long	port;
-	unsigned long	hwid;
-	unsigned long	type;
-	unsigned long	txtotal;
-	unsigned long	rxtotal;
-	unsigned long	txbuffered;
-	unsigned long	rxbuffered;
-	unsigned long	rxoverrun;
-	unsigned long	rxparity;
-	unsigned long	rxframing;
-	unsigned long	rxlost;
-	unsigned long	txbreaks;
-	unsigned long	rxbreaks;
-	unsigned long	txxon;
-	unsigned long	txxoff;
-	unsigned long	rxxon;
-	unsigned long	rxxoff;
-	unsigned long	txctson;
-	unsigned long	txctsoff;
-	unsigned long	rxrtson;
-	unsigned long	rxrtsoff;
-	unsigned long	modem;
-	unsigned long	state;
-	unsigned long	flags;
-	unsigned long	ttystate;
-	unsigned long	cflags;
-	unsigned long	iflags;
-	unsigned long	oflags;
-	unsigned long	lflags;
-	unsigned long	signals;
-} comstats_t;
-
-
-/*
- *	Board stats structure. Returns useful info about the board.
- */
-
-#define	COM_MAXPANELS	8
-
-typedef struct {
-	unsigned long	panel;
-	unsigned long	type;
-	unsigned long	hwid;
-	unsigned long	nrports;
-} companel_t;
-
-typedef struct {
-	unsigned long	brd;
-	unsigned long	type;
-	unsigned long	hwid;
-	unsigned long	state;
-	unsigned long	ioaddr;
-	unsigned long	ioaddr2;
-	unsigned long	memaddr;
-	unsigned long	irq;
-	unsigned long	nrpanels;
-	unsigned long	nrports;
-	companel_t	panels[COM_MAXPANELS];
-} combrd_t;
-
-
-/*
- *	Define the ioctl operations for stats stuff.
- */
-#include <linux/ioctl.h>
-
-#define	COM_GETPORTSTATS	_IO('c',30)
-#define	COM_CLRPORTSTATS	_IO('c',31)
-#define	COM_GETBRDSTATS		_IO('c',32)
-
-
-/*
- *	Define the set of ioctls that give user level access to the
- *	private port, panel and board structures. The argument required
- *	will be driver dependent!  
- */
-#define	COM_READPORT		_IO('c',40)
-#define	COM_READBOARD		_IO('c',41)
-#define	COM_READPANEL		_IO('c',42)
-
-/*****************************************************************************/
-#endif
diff --git a/include/linux/cpuidle.h b/include/linux/cpuidle.h
index 040b13b..279b1ea 100644
--- a/include/linux/cpuidle.h
+++ b/include/linux/cpuidle.h
@@ -194,6 +194,10 @@
 
 #ifdef CONFIG_ARCH_NEEDS_CPU_IDLE_COUPLED
 void cpuidle_coupled_parallel_barrier(struct cpuidle_device *dev, atomic_t *a);
+#else
+static inline void cpuidle_coupled_parallel_barrier(struct cpuidle_device *dev, atomic_t *a)
+{
+}
 #endif
 
 /******************************
diff --git a/include/linux/generic_serial.h b/include/linux/generic_serial.h
deleted file mode 100644
index 79b3eb3..0000000
--- a/include/linux/generic_serial.h
+++ /dev/null
@@ -1,35 +0,0 @@
-/*
- *  generic_serial.h
- *
- *  Copyright (C) 1998 R.E.Wolff@BitWizard.nl
- *
- *  written for the SX serial driver.
- *
- *  Version 0.1 -- December, 1998.
- */
-
-#ifndef GENERIC_SERIAL_H
-#define GENERIC_SERIAL_H
-
-#warning Use of this header is deprecated.
-#warning Since nobody sets the constants defined here for you, you should not, in any case, use them. Including the header is thus pointless.
-
-/* Flags */
-/* Warning: serial.h defines some ASYNC_ flags, they say they are "only"
-   used in serial.c, but they are also used in all other serial drivers. 
-   Make sure they don't clash with these here... */
-#define GS_TX_INTEN      0x00800000
-#define GS_RX_INTEN      0x00400000
-#define GS_ACTIVE        0x00200000
-
-#define GS_TYPE_NORMAL   1
-
-#define GS_DEBUG_FLUSH   0x00000001
-#define GS_DEBUG_BTR     0x00000002
-#define GS_DEBUG_TERMIOS 0x00000004
-#define GS_DEBUG_STUFF   0x00000008
-#define GS_DEBUG_CLOSE   0x00000010
-#define GS_DEBUG_FLOW    0x00000020
-#define GS_DEBUG_WRITE   0x00000040
-
-#endif
diff --git a/include/linux/istallion.h b/include/linux/istallion.h
deleted file mode 100644
index ad700a6..0000000
--- a/include/linux/istallion.h
+++ /dev/null
@@ -1,123 +0,0 @@
-/*****************************************************************************/
-
-/*
- *	istallion.h  -- stallion intelligent multiport serial driver.
- *
- *	Copyright (C) 1996-1998  Stallion Technologies
- *	Copyright (C) 1994-1996  Greg Ungerer.
- *
- *	This program is free software; you can redistribute it and/or modify
- *	it under the terms of the GNU General Public License as published by
- *	the Free Software Foundation; either version 2 of the License, or
- *	(at your option) any later version.
- *
- *	This program is distributed in the hope that it will be useful,
- *	but WITHOUT ANY WARRANTY; without even the implied warranty of
- *	MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *	GNU General Public License for more details.
- *
- *	You should have received a copy of the GNU General Public License
- *	along with this program; if not, write to the Free Software
- *	Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-/*****************************************************************************/
-#ifndef	_ISTALLION_H
-#define	_ISTALLION_H
-/*****************************************************************************/
-
-/*
- *	Define important driver constants here.
- */
-#define	STL_MAXBRDS		4
-#define	STL_MAXPANELS		4
-#define	STL_MAXPORTS		64
-#define	STL_MAXCHANS		(STL_MAXPORTS + 1)
-#define	STL_MAXDEVS		(STL_MAXBRDS * STL_MAXPORTS)
-
-
-/*
- *	Define a set of structures to hold all the board/panel/port info
- *	for our ports. These will be dynamically allocated as required at
- *	driver initialization time.
- */
-
-/*
- *	Port and board structures to hold status info about each object.
- *	The board structure contains pointers to structures for each port
- *	connected to it. Panels are not distinguished here, since
- *	communication with the slave board will always be on a per port
- *	basis.
- */
-struct stliport {
-	unsigned long		magic;
-	struct tty_port		port;
-	unsigned int		portnr;
-	unsigned int		panelnr;
-	unsigned int		brdnr;
-	unsigned long		state;
-	unsigned int		devnr;
-	int			baud_base;
-	int			custom_divisor;
-	int			closing_wait;
-	int			rc;
-	int			argsize;
-	void			*argp;
-	unsigned int		rxmarkmsk;
-	wait_queue_head_t	raw_wait;
-	struct asysigs		asig;
-	unsigned long		addr;
-	unsigned long		rxoffset;
-	unsigned long		txoffset;
-	unsigned long		sigs;
-	unsigned long		pflag;
-	unsigned int		rxsize;
-	unsigned int		txsize;
-	unsigned char		reqbit;
-	unsigned char		portidx;
-	unsigned char		portbit;
-};
-
-/*
- *	Use a structure of function pointers to do board level operations.
- *	These include, enable/disable, paging shared memory, interrupting, etc.
- */
-struct stlibrd {
-	unsigned long	magic;
-	unsigned int	brdnr;
-	unsigned int	brdtype;
-	unsigned long	state;
-	unsigned int	nrpanels;
-	unsigned int	nrports;
-	unsigned int	nrdevs;
-	unsigned int	iobase;
-	int		iosize;
-	unsigned long	memaddr;
-	void		__iomem *membase;
-	unsigned long	memsize;
-	int		pagesize;
-	int		hostoffset;
-	int		slaveoffset;
-	int		bitsize;
-	int		enabval;
-	unsigned int	panels[STL_MAXPANELS];
-	int		panelids[STL_MAXPANELS];
-	void		(*init)(struct stlibrd *brdp);
-	void		(*enable)(struct stlibrd *brdp);
-	void		(*reenable)(struct stlibrd *brdp);
-	void		(*disable)(struct stlibrd *brdp);
-	void		__iomem *(*getmemptr)(struct stlibrd *brdp, unsigned long offset, int line);
-	void		(*intr)(struct stlibrd *brdp);
-	void		(*reset)(struct stlibrd *brdp);
-	struct stliport	*ports[STL_MAXPORTS];
-};
-
-
-/*
- *	Define MAGIC numbers used for above structures.
- */
-#define	STLI_PORTMAGIC	0xe671c7a1
-#define	STLI_BOARDMAGIC	0x4bc6c825
-
-/*****************************************************************************/
-#endif
diff --git a/include/linux/kbd_kern.h b/include/linux/kbd_kern.h
index daf4a3a..b7c8cdc 100644
--- a/include/linux/kbd_kern.h
+++ b/include/linux/kbd_kern.h
@@ -65,7 +65,6 @@
 
 extern int kbd_init(void);
 
-extern unsigned char getledstate(void);
 extern void setledstate(struct kbd_struct *kbd, unsigned int led);
 
 extern int do_poke_blanked_console;
@@ -145,16 +144,4 @@
 
 extern unsigned int keymap_count;
 
-/* console.c */
-
-static inline void con_schedule_flip(struct tty_struct *t)
-{
-	unsigned long flags;
-	spin_lock_irqsave(&t->buf.lock, flags);
-	if (t->buf.tail != NULL)
-		t->buf.tail->commit = t->buf.tail->used;
-	spin_unlock_irqrestore(&t->buf.lock, flags);
-	schedule_work(&t->buf.work);
-}
-
 #endif
diff --git a/include/linux/kernel.h b/include/linux/kernel.h
index 6043821..594b419 100644
--- a/include/linux/kernel.h
+++ b/include/linux/kernel.h
@@ -82,10 +82,18 @@
 	__x - (__x % (y));				\
 }							\
 )
+
+/*
+ * Divide positive or negative dividend by positive divisor and round
+ * to closest integer. Result is undefined for negative divisors.
+ */
 #define DIV_ROUND_CLOSEST(x, divisor)(			\
 {							\
-	typeof(divisor) __divisor = divisor;		\
-	(((x) + ((__divisor) / 2)) / (__divisor));	\
+	typeof(x) __x = x;				\
+	typeof(divisor) __d = divisor;			\
+	(((typeof(x))-1) >= 0 || (__x) >= 0) ?		\
+		(((__x) + ((__d) / 2)) / (__d)) :	\
+		(((__x) - ((__d) / 2)) / (__d));	\
 }							\
 )
 
diff --git a/include/linux/ktime.h b/include/linux/ktime.h
index 603bec2..06177ba10 100644
--- a/include/linux/ktime.h
+++ b/include/linux/ktime.h
@@ -58,13 +58,6 @@
 
 typedef union ktime ktime_t;		/* Kill this */
 
-#define KTIME_MAX			((s64)~((u64)1 << 63))
-#if (BITS_PER_LONG == 64)
-# define KTIME_SEC_MAX			(KTIME_MAX / NSEC_PER_SEC)
-#else
-# define KTIME_SEC_MAX			LONG_MAX
-#endif
-
 /*
  * ktime_t definitions when using the 64-bit scalar representation:
  */
diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h
index 111aca5..4b27f9f 100644
--- a/include/linux/mmc/card.h
+++ b/include/linux/mmc/card.h
@@ -239,6 +239,7 @@
 #define MMC_QUIRK_BLK_NO_CMD23	(1<<7)		/* Avoid CMD23 for regular multiblock */
 #define MMC_QUIRK_BROKEN_BYTE_MODE_512 (1<<8)	/* Avoid sending 512 bytes in */
 #define MMC_QUIRK_LONG_READ_TIME (1<<9)		/* Data read time > CSD says */
+#define MMC_QUIRK_SEC_ERASE_TRIM_BROKEN (1<<10)	/* Skip secure for erase/trim */
 						/* byte mode */
 	unsigned int    poweroff_notify_state;	/* eMMC4.5 notify feature */
 #define MMC_NO_POWER_NOTIFICATION	0
diff --git a/include/linux/mv643xx_eth.h b/include/linux/mv643xx_eth.h
index 51bf8ad..49258e0 100644
--- a/include/linux/mv643xx_eth.h
+++ b/include/linux/mv643xx_eth.h
@@ -15,6 +15,8 @@
 #define MV643XX_ETH_SIZE_REG_4		0x2224
 #define MV643XX_ETH_BASE_ADDR_ENABLE_REG	0x2290
 
+#define MV643XX_TX_CSUM_DEFAULT_LIMIT	0
+
 struct mv643xx_eth_shared_platform_data {
 	struct mbus_dram_target_info	*dram;
 	struct platform_device	*shared_smi;
diff --git a/include/linux/omapfb.h b/include/linux/omapfb.h
index 4ff57e8..85af818 100644
--- a/include/linux/omapfb.h
+++ b/include/linux/omapfb.h
@@ -220,7 +220,12 @@
 
 #ifdef __KERNEL__
 
-#include <plat/board.h>
+struct omap_lcd_config {
+	char panel_name[16];
+	char ctrl_name[16];
+	s16  nreset_gpio;
+	u8   data_lines;
+};
 
 struct omapfb_platform_data {
 	struct omap_lcd_config		lcd;
diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h
index fc35260..6b4565c 100644
--- a/include/linux/pci_ids.h
+++ b/include/linux/pci_ids.h
@@ -2149,7 +2149,7 @@
 #define PCI_DEVICE_ID_TIGON3_5704S	0x16a8
 #define PCI_DEVICE_ID_NX2_57800_VF	0x16a9
 #define PCI_DEVICE_ID_NX2_5706S		0x16aa
-#define PCI_DEVICE_ID_NX2_57840_MF	0x16ab
+#define PCI_DEVICE_ID_NX2_57840_MF	0x16a4
 #define PCI_DEVICE_ID_NX2_5708S		0x16ac
 #define PCI_DEVICE_ID_NX2_57840_VF	0x16ad
 #define PCI_DEVICE_ID_NX2_57810_MF	0x16ae
diff --git a/include/linux/platform_data/max310x.h b/include/linux/platform_data/max310x.h
new file mode 100644
index 0000000..91648bf
--- /dev/null
+++ b/include/linux/platform_data/max310x.h
@@ -0,0 +1,67 @@
+/*
+ *  Maxim (Dallas) MAX3107/8 serial driver
+ *
+ *  Copyright (C) 2012 Alexander Shiyan <shc_work@mail.ru>
+ *
+ *  Based on max3100.c, by Christian Pellegrin <chripell@evolware.org>
+ *  Based on max3110.c, by Feng Tang <feng.tang@intel.com>
+ *  Based on max3107.c, by Aavamobile
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2 of the License, or
+ *  (at your option) any later version.
+ */
+
+#ifndef _MAX310X_H_
+#define _MAX310X_H_
+
+/*
+ * Example board initialization data:
+ *
+ * static struct max310x_pdata max3107_pdata = {
+ *	.driver_flags	= MAX310X_EXT_CLK,
+ *	.uart_flags[0]	= MAX310X_ECHO_SUPRESS | MAX310X_AUTO_DIR_CTRL,
+ *	.frequency	= 3686400,
+ *	.gpio_base	= -1,
+ * };
+ *
+ * static struct spi_board_info spi_device_max3107[] = {
+ *	{
+ *		.modalias	= "max3107",
+ *		.irq		= IRQ_EINT3,
+ *		.bus_num	= 1,
+ *		.chip_select	= 1,
+ *		.platform_data	= &max3107_pdata,
+ *	},
+ * };
+ */
+
+#define MAX310X_MAX_UARTS	1
+
+/* MAX310X platform data structure */
+struct max310x_pdata {
+	/* Flags global to driver */
+	const u8		driver_flags:2;
+#define MAX310X_EXT_CLK		(0x00000001)	/* External clock enable */
+#define MAX310X_AUTOSLEEP	(0x00000002)	/* Enable AutoSleep mode */
+	/* Flags global to UART port */
+	const u8		uart_flags[MAX310X_MAX_UARTS];
+#define MAX310X_LOOPBACK	(0x00000001)	/* Loopback mode enable */
+#define MAX310X_ECHO_SUPRESS	(0x00000002)	/* Enable echo supress */
+#define MAX310X_AUTO_DIR_CTRL	(0x00000004)	/* Enable Auto direction
+						 * control (RS-485)
+						 */
+	/* Frequency (extrenal clock or crystal) */
+	const int		frequency;
+	/* GPIO base number (can be negative) */
+	const int		gpio_base;
+	/* Called during startup */
+	void (*init)(void);
+	/* Called before finish */
+	void (*exit)(void);
+	/* Suspend callback */
+	void (*suspend)(int do_suspend);
+};
+
+#endif
diff --git a/include/linux/platform_data/omap1_bl.h b/include/linux/platform_data/omap1_bl.h
new file mode 100644
index 0000000..881a8e9
--- /dev/null
+++ b/include/linux/platform_data/omap1_bl.h
@@ -0,0 +1,11 @@
+#ifndef __OMAP1_BL_H__
+#define __OMAP1_BL_H__
+
+#include <linux/device.h>
+
+struct omap_backlight_config {
+	int default_intensity;
+	int (*set_power)(struct device *dev, int state);
+};
+
+#endif
diff --git a/include/linux/platform_data/sccnxp.h b/include/linux/platform_data/sccnxp.h
new file mode 100644
index 0000000..7311ccd
--- /dev/null
+++ b/include/linux/platform_data/sccnxp.h
@@ -0,0 +1,93 @@
+/*
+ *  NXP (Philips) SCC+++(SCN+++) serial driver
+ *
+ *  Copyright (C) 2012 Alexander Shiyan <shc_work@mail.ru>
+ *
+ *  Based on sc26xx.c, by Thomas Bogendörfer (tsbogend@alpha.franken.de)
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2 of the License, or
+ *  (at your option) any later version.
+ */
+
+#ifndef __SCCNXP_H
+#define __SCCNXP_H
+
+#define SCCNXP_MAX_UARTS	2
+
+/* Output lines */
+#define LINE_OP0		1
+#define LINE_OP1		2
+#define LINE_OP2		3
+#define LINE_OP3		4
+#define LINE_OP4		5
+#define LINE_OP5		6
+#define LINE_OP6		7
+#define LINE_OP7		8
+
+/* Input lines */
+#define LINE_IP0		9
+#define LINE_IP1		10
+#define LINE_IP2		11
+#define LINE_IP3		12
+#define LINE_IP4		13
+#define LINE_IP5		14
+#define LINE_IP6		15
+
+/* Signals */
+#define DTR_OP			0	/* DTR */
+#define RTS_OP			4	/* RTS */
+#define DSR_IP			8	/* DSR */
+#define CTS_IP			12	/* CTS */
+#define DCD_IP			16	/* DCD */
+#define RNG_IP			20	/* RNG */
+
+#define DIR_OP			24	/* Special signal for control RS-485.
+					 * Goes high when transmit,
+					 * then goes low.
+					 */
+
+/* Routing control signal 'sig' to line 'line' */
+#define MCTRL_SIG(sig, line)	((line) << (sig))
+
+/*
+ * Example board initialization data:
+ *
+ * static struct resource sc2892_resources[] = {
+ *	DEFINE_RES_MEM(UART_PHYS_START, 0x10),
+ *	DEFINE_RES_IRQ(IRQ_EXT2),
+ * };
+ *
+ * static struct sccnxp_pdata sc2892_info = {
+ *	.frequency	= 3686400,
+ *	.mctrl_cfg[0]	= MCTRL_SIG(DIR_OP, LINE_OP0),
+ *	.mctrl_cfg[1]	= MCTRL_SIG(DIR_OP, LINE_OP1),
+ * };
+ *
+ * static struct platform_device sc2892 = {
+ *	.name		= "sc2892",
+ *	.id		= -1,
+ *	.resource	= sc2892_resources,
+ *	.num_resources	= ARRAY_SIZE(sc2892_resources),
+ *	.dev = {
+ *		.platform_data	= &sc2892_info,
+ *	},
+ * };
+ */
+
+/* SCCNXP platform data structure */
+struct sccnxp_pdata {
+	/* Frequency (extrenal clock or crystal) */
+	int			frequency;
+	/* Shift for A0 line */
+	const u8		reg_shift;
+	/* Modem control lines configuration */
+	const u32		mctrl_cfg[SCCNXP_MAX_UARTS];
+	/* Called during startup */
+	void (*init)(void);
+	/* Called before finish */
+	void (*exit)(void);
+};
+
+#endif
diff --git a/include/linux/sc26198.h b/include/linux/sc26198.h
deleted file mode 100644
index 7ca35ab..0000000
--- a/include/linux/sc26198.h
+++ /dev/null
@@ -1,533 +0,0 @@
-/*****************************************************************************/
-
-/*
- *	sc26198.h  -- SC26198 UART hardware info.
- *
- *	Copyright (C) 1995-1998  Stallion Technologies
- *
- *	This program is free software; you can redistribute it and/or modify
- *	it under the terms of the GNU General Public License as published by
- *	the Free Software Foundation; either version 2 of the License, or
- *	(at your option) any later version.
- *
- *	This program is distributed in the hope that it will be useful,
- *	but WITHOUT ANY WARRANTY; without even the implied warranty of
- *	MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *	GNU General Public License for more details.
- *
- *	You should have received a copy of the GNU General Public License
- *	along with this program; if not, write to the Free Software
- *	Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-/*****************************************************************************/
-#ifndef	_SC26198_H
-#define	_SC26198_H
-/*****************************************************************************/
-
-/*
- *	Define the number of async ports per sc26198 uart device.
- */
-#define	SC26198_PORTS		8
-
-/*
- *	Baud rate timing clocks. All derived from a master 14.7456 MHz clock.
- */
-#define	SC26198_MASTERCLOCK	14745600L
-#define	SC26198_DCLK		(SC26198_MASTERCLOCK)
-#define	SC26198_CCLK		(SC26198_MASTERCLOCK / 2)
-#define	SC26198_BCLK		(SC26198_MASTERCLOCK / 4)
-
-/*
- *	Define internal FIFO sizes for the 26198 ports.
- */
-#define	SC26198_TXFIFOSIZE	16
-#define	SC26198_RXFIFOSIZE	16
-
-/*****************************************************************************/
-
-/*
- *	Global register definitions. These registers are global to each 26198
- *	device, not specific ports on it.
- */
-#define	TSTR		0x0d
-#define	GCCR		0x0f
-#define	ICR		0x1b
-#define	WDTRCR		0x1d
-#define	IVR		0x1f
-#define	BRGTRUA		0x84
-#define	GPOSR		0x87
-#define	GPOC		0x8b
-#define	UCIR		0x8c
-#define	CIR		0x8c
-#define	BRGTRUB		0x8d
-#define	GRXFIFO		0x8e
-#define	GTXFIFO		0x8e
-#define	GCCR2		0x8f
-#define	BRGTRLA		0x94
-#define	GPOR		0x97
-#define	GPOD		0x9b
-#define	BRGTCR		0x9c
-#define	GICR		0x9c
-#define	BRGTRLB		0x9d
-#define	GIBCR		0x9d
-#define	GITR		0x9f
-
-/*
- *	Per port channel registers. These are the register offsets within
- *	the port address space, so need to have the port address (0 to 7)
- *	inserted in bit positions 4:6.
- */
-#define	MR0		0x00
-#define	MR1		0x01
-#define	IOPCR		0x02
-#define	BCRBRK		0x03
-#define	BCRCOS		0x04
-#define	BCRX		0x06
-#define	BCRA		0x07
-#define	XONCR		0x08
-#define	XOFFCR		0x09
-#define	ARCR		0x0a
-#define	RXCSR		0x0c
-#define	TXCSR		0x0e
-#define	MR2		0x80
-#define	SR		0x81
-#define SCCR		0x81
-#define	ISR		0x82
-#define	IMR		0x82
-#define	TXFIFO		0x83
-#define	RXFIFO		0x83
-#define	IPR		0x84
-#define	IOPIOR		0x85
-#define	XISR		0x86
-
-/*
- *	For any given port calculate the address to use to access a specified
- *	register. This is only used for unusual access, mostly this is done
- *	through the assembler access routines.
- */
-#define	SC26198_PORTREG(port,reg)	((((port) & 0x07) << 4) | (reg))
-
-/*****************************************************************************/
-
-/*
- *	Global configuration control register bit definitions.
- */
-#define	GCCR_NOACK		0x00
-#define	GCCR_IVRACK		0x02
-#define	GCCR_IVRCHANACK		0x04
-#define	GCCR_IVRTYPCHANACK	0x06
-#define	GCCR_ASYNCCYCLE		0x00
-#define	GCCR_SYNCCYCLE		0x40
-
-/*****************************************************************************/
-
-/*
- *	Mode register 0 bit definitions.
- */
-#define	MR0_ADDRNONE		0x00
-#define	MR0_AUTOWAKE		0x01
-#define	MR0_AUTODOZE		0x02
-#define	MR0_AUTOWAKEDOZE	0x03
-#define	MR0_SWFNONE		0x00
-#define	MR0_SWFTX		0x04
-#define	MR0_SWFRX		0x08
-#define	MR0_SWFRXTX		0x0c
-#define	MR0_TXMASK		0x30
-#define	MR0_TXEMPTY		0x00
-#define	MR0_TXHIGH		0x10
-#define	MR0_TXHALF		0x20
-#define	MR0_TXRDY		0x00
-#define	MR0_ADDRNT		0x00
-#define	MR0_ADDRT		0x40
-#define	MR0_SWFNT		0x00
-#define	MR0_SWFT		0x80
-
-/*
- *	Mode register 1 bit definitions.
- */
-#define	MR1_CS5			0x00
-#define	MR1_CS6			0x01
-#define	MR1_CS7			0x02
-#define	MR1_CS8			0x03
-#define	MR1_PAREVEN		0x00
-#define	MR1_PARODD		0x04
-#define	MR1_PARENB		0x00
-#define	MR1_PARFORCE		0x08
-#define	MR1_PARNONE		0x10
-#define	MR1_PARSPECIAL		0x18
-#define	MR1_ERRCHAR		0x00
-#define	MR1_ERRBLOCK		0x20
-#define	MR1_ISRUNMASKED		0x00
-#define	MR1_ISRMASKED		0x40
-#define	MR1_AUTORTS		0x80
-
-/*
- *	Mode register 2 bit definitions.
- */
-#define	MR2_STOP1		0x00
-#define	MR2_STOP15		0x01
-#define	MR2_STOP2		0x02
-#define	MR2_STOP916		0x03
-#define	MR2_RXFIFORDY		0x00
-#define	MR2_RXFIFOHALF		0x04
-#define	MR2_RXFIFOHIGH		0x08
-#define	MR2_RXFIFOFULL		0x0c
-#define	MR2_AUTOCTS		0x10
-#define	MR2_TXRTS		0x20
-#define	MR2_MODENORM		0x00
-#define	MR2_MODEAUTOECHO	0x40
-#define	MR2_MODELOOP		0x80
-#define	MR2_MODEREMECHO		0xc0
-
-/*****************************************************************************/
-
-/*
- *	Baud Rate Generator (BRG) selector values.
- */
-#define	BRG_50			0x00
-#define	BRG_75			0x01
-#define	BRG_150			0x02
-#define	BRG_200			0x03
-#define	BRG_300			0x04
-#define	BRG_450			0x05
-#define	BRG_600			0x06
-#define	BRG_900			0x07
-#define	BRG_1200		0x08
-#define	BRG_1800		0x09
-#define	BRG_2400		0x0a
-#define	BRG_3600		0x0b
-#define	BRG_4800		0x0c
-#define	BRG_7200		0x0d
-#define	BRG_9600		0x0e
-#define	BRG_14400		0x0f
-#define	BRG_19200		0x10
-#define	BRG_28200		0x11
-#define	BRG_38400		0x12
-#define	BRG_57600		0x13
-#define	BRG_115200		0x14
-#define	BRG_230400		0x15
-#define	BRG_GIN0		0x16
-#define	BRG_GIN1		0x17
-#define	BRG_CT0			0x18
-#define	BRG_CT1			0x19
-#define	BRG_RX2TX316		0x1b
-#define	BRG_RX2TX31		0x1c
-
-#define	SC26198_MAXBAUD		921600
-
-/*****************************************************************************/
-
-/*
- *	Command register command definitions.
- */
-#define	CR_NULL			0x04
-#define	CR_ADDRNORMAL		0x0c
-#define	CR_RXRESET		0x14
-#define	CR_TXRESET		0x1c
-#define	CR_CLEARRXERR		0x24
-#define	CR_BREAKRESET		0x2c
-#define	CR_TXSTARTBREAK		0x34
-#define	CR_TXSTOPBREAK		0x3c
-#define	CR_RTSON		0x44
-#define	CR_RTSOFF		0x4c
-#define	CR_ADDRINIT		0x5c
-#define	CR_RXERRBLOCK		0x6c
-#define	CR_TXSENDXON		0x84
-#define	CR_TXSENDXOFF		0x8c
-#define	CR_GANGXONSET		0x94
-#define	CR_GANGXOFFSET		0x9c
-#define	CR_GANGXONINIT		0xa4
-#define	CR_GANGXOFFINIT		0xac
-#define	CR_HOSTXON		0xb4
-#define	CR_HOSTXOFF		0xbc
-#define	CR_CANCELXOFF		0xc4
-#define	CR_ADDRRESET		0xdc
-#define	CR_RESETALLPORTS	0xf4
-#define	CR_RESETALL		0xfc
-
-#define	CR_RXENABLE		0x01
-#define	CR_TXENABLE		0x02
-
-/*****************************************************************************/
-
-/*
- *	Channel status register.
- */
-#define	SR_RXRDY		0x01
-#define	SR_RXFULL		0x02
-#define	SR_TXRDY		0x04
-#define	SR_TXEMPTY		0x08
-#define	SR_RXOVERRUN		0x10
-#define	SR_RXPARITY		0x20
-#define	SR_RXFRAMING		0x40
-#define	SR_RXBREAK		0x80
-
-#define	SR_RXERRS		(SR_RXPARITY | SR_RXFRAMING | SR_RXOVERRUN)
-
-/*****************************************************************************/
-
-/*
- *	Interrupt status register and interrupt mask register bit definitions.
- */
-#define	IR_TXRDY		0x01
-#define	IR_RXRDY		0x02
-#define	IR_RXBREAK		0x04
-#define	IR_XONXOFF		0x10
-#define	IR_ADDRRECOG		0x20
-#define	IR_RXWATCHDOG		0x40
-#define	IR_IOPORT		0x80
-
-/*****************************************************************************/
-
-/*
- *	Interrupt vector register field definitions.
- */
-#define	IVR_CHANMASK		0x07
-#define	IVR_TYPEMASK		0x18
-#define	IVR_CONSTMASK		0xc0
-
-#define	IVR_RXDATA		0x10
-#define	IVR_RXBADDATA		0x18
-#define	IVR_TXDATA		0x08
-#define	IVR_OTHER		0x00
-
-/*****************************************************************************/
-
-/*
- *	BRG timer control register bit definitions.
- */
-#define	BRGCTCR_DISABCLK0	0x00
-#define	BRGCTCR_ENABCLK0	0x08
-#define	BRGCTCR_DISABCLK1	0x00
-#define	BRGCTCR_ENABCLK1	0x80
-
-#define	BRGCTCR_0SCLK16		0x00
-#define	BRGCTCR_0SCLK32		0x01
-#define	BRGCTCR_0SCLK64		0x02
-#define	BRGCTCR_0SCLK128	0x03
-#define	BRGCTCR_0X1		0x04
-#define	BRGCTCR_0X12		0x05
-#define	BRGCTCR_0IO1A		0x06
-#define	BRGCTCR_0GIN0		0x07
-
-#define	BRGCTCR_1SCLK16		0x00
-#define	BRGCTCR_1SCLK32		0x10
-#define	BRGCTCR_1SCLK64		0x20
-#define	BRGCTCR_1SCLK128	0x30
-#define	BRGCTCR_1X1		0x40
-#define	BRGCTCR_1X12		0x50
-#define	BRGCTCR_1IO1B		0x60
-#define	BRGCTCR_1GIN1		0x70
-
-/*****************************************************************************/
-
-/*
- *	Watch dog timer enable register.
- */
-#define	WDTRCR_ENABALL		0xff
-
-/*****************************************************************************/
-
-/*
- *	XON/XOFF interrupt status register.
- */
-#define	XISR_TXCHARMASK		0x03
-#define	XISR_TXCHARNORMAL	0x00
-#define	XISR_TXWAIT		0x01
-#define	XISR_TXXOFFPEND		0x02
-#define	XISR_TXXONPEND		0x03
-
-#define	XISR_TXFLOWMASK		0x0c
-#define	XISR_TXNORMAL		0x00
-#define	XISR_TXSTOPPEND		0x04
-#define	XISR_TXSTARTED		0x08
-#define	XISR_TXSTOPPED		0x0c
-
-#define	XISR_RXFLOWMASK		0x30
-#define	XISR_RXFLOWNONE		0x00
-#define	XISR_RXXONSENT		0x10
-#define	XISR_RXXOFFSENT		0x20
-
-#define	XISR_RXXONGOT		0x40
-#define	XISR_RXXOFFGOT		0x80
-
-/*****************************************************************************/
-
-/*
- *	Current interrupt register.
- */
-#define	CIR_TYPEMASK		0xc0
-#define	CIR_TYPEOTHER		0x00
-#define	CIR_TYPETX		0x40
-#define	CIR_TYPERXGOOD		0x80
-#define	CIR_TYPERXBAD		0xc0
-
-#define	CIR_RXDATA		0x80
-#define	CIR_RXBADDATA		0x40
-#define	CIR_TXDATA		0x40
-
-#define	CIR_CHANMASK		0x07
-#define	CIR_CNTMASK		0x38
-
-#define	CIR_SUBTYPEMASK		0x38
-#define	CIR_SUBNONE		0x00
-#define	CIR_SUBCOS		0x08
-#define	CIR_SUBADDR		0x10
-#define	CIR_SUBXONXOFF		0x18
-#define	CIR_SUBBREAK		0x28
-
-/*****************************************************************************/
-
-/*
- *	Global interrupting channel register.
- */
-#define	GICR_CHANMASK		0x07
-
-/*****************************************************************************/
-
-/*
- *	Global interrupting byte count register.
- */
-#define	GICR_COUNTMASK		0x0f
-
-/*****************************************************************************/
-
-/*
- *	Global interrupting type register.
- */
-#define	GITR_RXMASK		0xc0
-#define	GITR_RXNONE		0x00
-#define	GITR_RXBADDATA		0x80
-#define	GITR_RXGOODDATA		0xc0
-#define	GITR_TXDATA		0x20
-
-#define	GITR_SUBTYPEMASK	0x07
-#define	GITR_SUBNONE		0x00
-#define	GITR_SUBCOS		0x01
-#define	GITR_SUBADDR		0x02
-#define	GITR_SUBXONXOFF		0x03
-#define	GITR_SUBBREAK		0x05
-
-/*****************************************************************************/
-
-/*
- *	Input port change register.
- */
-#define	IPR_CTS			0x01
-#define	IPR_DTR			0x02
-#define	IPR_RTS			0x04
-#define	IPR_DCD			0x08
-#define	IPR_CTSCHANGE		0x10
-#define	IPR_DTRCHANGE		0x20
-#define	IPR_RTSCHANGE		0x40
-#define	IPR_DCDCHANGE		0x80
-
-#define	IPR_CHANGEMASK		0xf0
-
-/*****************************************************************************/
-
-/*
- *	IO port interrupt and output register.
- */
-#define	IOPR_CTS		0x01
-#define	IOPR_DTR		0x02
-#define	IOPR_RTS		0x04
-#define	IOPR_DCD		0x08
-#define	IOPR_CTSCOS		0x10
-#define	IOPR_DTRCOS		0x20
-#define	IOPR_RTSCOS		0x40
-#define	IOPR_DCDCOS		0x80
-
-/*****************************************************************************/
-
-/*
- *	IO port configuration register.
- */
-#define	IOPCR_SETCTS		0x00
-#define	IOPCR_SETDTR		0x04
-#define	IOPCR_SETRTS		0x10
-#define	IOPCR_SETDCD		0x00
-
-#define	IOPCR_SETSIGS		(IOPCR_SETRTS | IOPCR_SETRTS | IOPCR_SETDTR | IOPCR_SETDCD)
-
-/*****************************************************************************/
-
-/*
- *	General purpose output select register.
- */
-#define	GPORS_TXC1XA		0x08
-#define	GPORS_TXC16XA		0x09
-#define	GPORS_RXC16XA		0x0a
-#define	GPORS_TXC16XB		0x0b
-#define	GPORS_GPOR3		0x0c
-#define	GPORS_GPOR2		0x0d
-#define	GPORS_GPOR1		0x0e
-#define	GPORS_GPOR0		0x0f
-
-/*****************************************************************************/
-
-/*
- *	General purpose output register.
- */
-#define	GPOR_0			0x01
-#define	GPOR_1			0x02
-#define	GPOR_2			0x04
-#define	GPOR_3			0x08
-
-/*****************************************************************************/
-
-/*
- *	General purpose output clock register.
- */
-#define	GPORC_0NONE		0x00
-#define	GPORC_0GIN0		0x01
-#define	GPORC_0GIN1		0x02
-#define	GPORC_0IO3A		0x02
-
-#define	GPORC_1NONE		0x00
-#define	GPORC_1GIN0		0x04
-#define	GPORC_1GIN1		0x08
-#define	GPORC_1IO3C		0x0c
-
-#define	GPORC_2NONE		0x00
-#define	GPORC_2GIN0		0x10
-#define	GPORC_2GIN1		0x20
-#define	GPORC_2IO3E		0x20
-
-#define	GPORC_3NONE		0x00
-#define	GPORC_3GIN0		0x40
-#define	GPORC_3GIN1		0x80
-#define	GPORC_3IO3G		0xc0
-
-/*****************************************************************************/
-
-/*
- *	General purpose output data register.
- */
-#define	GPOD_0MASK		0x03
-#define	GPOD_0SET1		0x00
-#define	GPOD_0SET0		0x01
-#define	GPOD_0SETR0		0x02
-#define	GPOD_0SETIO3B		0x03
-
-#define	GPOD_1MASK		0x0c
-#define	GPOD_1SET1		0x00
-#define	GPOD_1SET0		0x04
-#define	GPOD_1SETR0		0x08
-#define	GPOD_1SETIO3D		0x0c
-
-#define	GPOD_2MASK		0x30
-#define	GPOD_2SET1		0x00
-#define	GPOD_2SET0		0x10
-#define	GPOD_2SETR0		0x20
-#define	GPOD_2SETIO3F		0x30
-
-#define	GPOD_3MASK		0xc0
-#define	GPOD_3SET1		0x00
-#define	GPOD_3SET0		0x40
-#define	GPOD_3SETR0		0x80
-#define	GPOD_3SETIO3H		0xc0
-
-/*****************************************************************************/
-#endif
diff --git a/include/linux/serial.h b/include/linux/serial.h
index 90e9f98..861e51d 100644
--- a/include/linux/serial.h
+++ b/include/linux/serial.h
@@ -12,9 +12,12 @@
 
 #include <linux/types.h>
 
+#include <linux/tty_flags.h>
+
 #ifdef __KERNEL__
 #include <asm/page.h>
 
+
 /*
  * Counters of the input lines (CTS, DSR, RI, CD) interrupts
  */
@@ -83,89 +86,11 @@
 #define SERIAL_IO_HUB6	1
 #define SERIAL_IO_MEM	2
 
-struct serial_uart_config {
-	char	*name;
-	int	dfl_xmit_fifo_size;
-	int	flags;
-};
-
 #define UART_CLEAR_FIFO		0x01
 #define UART_USE_FIFO		0x02
 #define UART_STARTECH		0x04
 #define UART_NATSEMI		0x08
 
-/*
- * Definitions for async_struct (and serial_struct) flags field
- *
- * Define ASYNCB_* for convenient use with {test,set,clear}_bit.
- */
-#define ASYNCB_HUP_NOTIFY	 0 /* Notify getty on hangups and closes
-				    * on the callout port */
-#define ASYNCB_FOURPORT		 1 /* Set OU1, OUT2 per AST Fourport settings */
-#define ASYNCB_SAK		 2 /* Secure Attention Key (Orange book) */
-#define ASYNCB_SPLIT_TERMIOS	 3 /* Separate termios for dialin/callout */
-#define ASYNCB_SPD_HI		 4 /* Use 56000 instead of 38400 bps */
-#define ASYNCB_SPD_VHI		 5 /* Use 115200 instead of 38400 bps */
-#define ASYNCB_SKIP_TEST	 6 /* Skip UART test during autoconfiguration */
-#define ASYNCB_AUTO_IRQ		 7 /* Do automatic IRQ during
-				    * autoconfiguration */
-#define ASYNCB_SESSION_LOCKOUT	 8 /* Lock out cua opens based on session */
-#define ASYNCB_PGRP_LOCKOUT	 9 /* Lock out cua opens based on pgrp */
-#define ASYNCB_CALLOUT_NOHUP	10 /* Don't do hangups for cua device */
-#define ASYNCB_HARDPPS_CD	11 /* Call hardpps when CD goes high  */
-#define ASYNCB_SPD_SHI		12 /* Use 230400 instead of 38400 bps */
-#define ASYNCB_LOW_LATENCY	13 /* Request low latency behaviour */
-#define ASYNCB_BUGGY_UART	14 /* This is a buggy UART, skip some safety
-				    * checks.  Note: can be dangerous! */
-#define ASYNCB_AUTOPROBE	15 /* Port was autoprobed by PCI or PNP code */
-#define ASYNCB_LAST_USER	15
-
-/* Internal flags used only by kernel */
-#define ASYNCB_INITIALIZED	31 /* Serial port was initialized */
-#define ASYNCB_SUSPENDED	30 /* Serial port is suspended */
-#define ASYNCB_NORMAL_ACTIVE	29 /* Normal device is active */
-#define ASYNCB_BOOT_AUTOCONF	28 /* Autoconfigure port on bootup */
-#define ASYNCB_CLOSING		27 /* Serial port is closing */
-#define ASYNCB_CTS_FLOW		26 /* Do CTS flow control */
-#define ASYNCB_CHECK_CD		25 /* i.e., CLOCAL */
-#define ASYNCB_SHARE_IRQ	24 /* for multifunction cards, no longer used */
-#define ASYNCB_CONS_FLOW	23 /* flow control for console  */
-#define ASYNCB_FIRST_KERNEL	22
-
-#define ASYNC_HUP_NOTIFY	(1U << ASYNCB_HUP_NOTIFY)
-#define ASYNC_SUSPENDED		(1U << ASYNCB_SUSPENDED)
-#define ASYNC_FOURPORT		(1U << ASYNCB_FOURPORT)
-#define ASYNC_SAK		(1U << ASYNCB_SAK)
-#define ASYNC_SPLIT_TERMIOS	(1U << ASYNCB_SPLIT_TERMIOS)
-#define ASYNC_SPD_HI		(1U << ASYNCB_SPD_HI)
-#define ASYNC_SPD_VHI		(1U << ASYNCB_SPD_VHI)
-#define ASYNC_SKIP_TEST		(1U << ASYNCB_SKIP_TEST)
-#define ASYNC_AUTO_IRQ		(1U << ASYNCB_AUTO_IRQ)
-#define ASYNC_SESSION_LOCKOUT	(1U << ASYNCB_SESSION_LOCKOUT)
-#define ASYNC_PGRP_LOCKOUT	(1U << ASYNCB_PGRP_LOCKOUT)
-#define ASYNC_CALLOUT_NOHUP	(1U << ASYNCB_CALLOUT_NOHUP)
-#define ASYNC_HARDPPS_CD	(1U << ASYNCB_HARDPPS_CD)
-#define ASYNC_SPD_SHI		(1U << ASYNCB_SPD_SHI)
-#define ASYNC_LOW_LATENCY	(1U << ASYNCB_LOW_LATENCY)
-#define ASYNC_BUGGY_UART	(1U << ASYNCB_BUGGY_UART)
-#define ASYNC_AUTOPROBE		(1U << ASYNCB_AUTOPROBE)
-
-#define ASYNC_FLAGS		((1U << (ASYNCB_LAST_USER + 1)) - 1)
-#define ASYNC_USR_MASK		(ASYNC_SPD_MASK|ASYNC_CALLOUT_NOHUP| \
-		ASYNC_LOW_LATENCY)
-#define ASYNC_SPD_CUST		(ASYNC_SPD_HI|ASYNC_SPD_VHI)
-#define ASYNC_SPD_WARP		(ASYNC_SPD_HI|ASYNC_SPD_SHI)
-#define ASYNC_SPD_MASK		(ASYNC_SPD_HI|ASYNC_SPD_VHI|ASYNC_SPD_SHI)
-
-#define ASYNC_INITIALIZED	(1U << ASYNCB_INITIALIZED)
-#define ASYNC_NORMAL_ACTIVE	(1U << ASYNCB_NORMAL_ACTIVE)
-#define ASYNC_BOOT_AUTOCONF	(1U << ASYNCB_BOOT_AUTOCONF)
-#define ASYNC_CLOSING		(1U << ASYNCB_CLOSING)
-#define ASYNC_CTS_FLOW		(1U << ASYNCB_CTS_FLOW)
-#define ASYNC_CHECK_CD		(1U << ASYNCB_CHECK_CD)
-#define ASYNC_SHARE_IRQ		(1U << ASYNCB_SHARE_IRQ)
-#define ASYNC_CONS_FLOW		(1U << ASYNCB_CONS_FLOW)
-#define ASYNC_INTERNAL_FLAGS	(~((1U << ASYNCB_FIRST_KERNEL) - 1))
 
 /*
  * Multiport serial configuration structure --- external structure
diff --git a/include/linux/serial167.h b/include/linux/serial167.h
deleted file mode 100644
index 59c81b7..0000000
--- a/include/linux/serial167.h
+++ /dev/null
@@ -1,157 +0,0 @@
-/*
- * serial167.h
- *
- * Richard Hirst [richard@sleepie.demon.co.uk]
- *
- * Based on cyclades.h
- */
-
-struct cyclades_monitor {
-        unsigned long           int_count;
-        unsigned long           char_count;
-        unsigned long           char_max;
-        unsigned long           char_last;
-};
-
-/*
- * This is our internal structure for each serial port's state.
- * 
- * Many fields are paralleled by the structure used by the serial_struct
- * structure.
- *
- * For definitions of the flags field, see tty.h
- */
-
-struct cyclades_port {
-	int                     magic;
-	int                     type;
-	int			card;
-	int			line;
-	int			flags; 		/* defined in tty.h */
-	struct tty_struct 	*tty;
-	int			read_status_mask;
-	int			timeout;
-	int			xmit_fifo_size;
-	int                     cor1,cor2,cor3,cor4,cor5,cor6,cor7;
-	int                     tbpr,tco,rbpr,rco;
-	int			ignore_status_mask;
-	int			close_delay;
-	int			IER; 	/* Interrupt Enable Register */
-	unsigned long		last_active;
-	int			count;	/* # of fd on device */
-	int                     x_char; /* to be pushed out ASAP */
-	int                     x_break;
-	int			blocked_open; /* # of blocked opens */
-	unsigned char 		*xmit_buf;
-	int			xmit_head;
-	int			xmit_tail;
-	int			xmit_cnt;
-        int                     default_threshold;
-        int                     default_timeout;
-	wait_queue_head_t	open_wait;
-	wait_queue_head_t	close_wait;
-        struct cyclades_monitor mon;
-};
-
-#define CYCLADES_MAGIC  0x4359
-
-#define CYGETMON                0x435901
-#define CYGETTHRESH             0x435902
-#define CYSETTHRESH             0x435903
-#define CYGETDEFTHRESH          0x435904
-#define CYSETDEFTHRESH          0x435905
-#define CYGETTIMEOUT            0x435906
-#define CYSETTIMEOUT            0x435907
-#define CYGETDEFTIMEOUT         0x435908
-#define CYSETDEFTIMEOUT         0x435909
-
-#define CyMaxChipsPerCard 1
-
-/**** cd2401 registers ****/
-
-#define CyGFRCR         (0x81)
-#define CyCCR		(0x13)
-#define      CyCLR_CHAN		(0x40)
-#define      CyINIT_CHAN	(0x20)
-#define      CyCHIP_RESET	(0x10)
-#define      CyENB_XMTR		(0x08)
-#define      CyDIS_XMTR		(0x04)
-#define      CyENB_RCVR		(0x02)
-#define      CyDIS_RCVR		(0x01)
-#define CyCAR		(0xee)
-#define CyIER		(0x11)
-#define      CyMdmCh		(0x80)
-#define      CyRxExc		(0x20)
-#define      CyRxData		(0x08)
-#define      CyTxMpty		(0x02)
-#define      CyTxRdy		(0x01)
-#define CyLICR		(0x26)
-#define CyRISR		(0x89)
-#define      CyTIMEOUT		(0x80)
-#define      CySPECHAR		(0x70)
-#define      CyOVERRUN		(0x08)
-#define      CyPARITY		(0x04)
-#define      CyFRAME		(0x02)
-#define      CyBREAK		(0x01)
-#define CyREOIR		(0x84)
-#define CyTEOIR		(0x85)
-#define CyMEOIR		(0x86)
-#define      CyNOTRANS		(0x08)
-#define CyRFOC		(0x30)
-#define CyRDR		(0xf8)
-#define CyTDR		(0xf8)
-#define CyMISR		(0x8b)
-#define CyRISR		(0x89)
-#define CyTISR		(0x8a)
-#define CyMSVR1		(0xde)
-#define CyMSVR2		(0xdf)
-#define      CyDSR		(0x80)
-#define      CyDCD		(0x40)
-#define      CyCTS		(0x20)
-#define      CyDTR		(0x02)
-#define      CyRTS		(0x01)
-#define CyRTPRL		(0x25)
-#define CyRTPRH		(0x24)
-#define CyCOR1		(0x10)
-#define      CyPARITY_NONE	(0x00)
-#define      CyPARITY_E		(0x40)
-#define      CyPARITY_O		(0xC0)
-#define      Cy_5_BITS		(0x04)
-#define      Cy_6_BITS		(0x05)
-#define      Cy_7_BITS		(0x06)
-#define      Cy_8_BITS		(0x07)
-#define CyCOR2		(0x17)
-#define      CyETC		(0x20)
-#define      CyCtsAE		(0x02)
-#define CyCOR3		(0x16)
-#define      Cy_1_STOP		(0x02)
-#define      Cy_2_STOP		(0x04)
-#define CyCOR4		(0x15)
-#define      CyREC_FIFO		(0x0F)  /* Receive FIFO threshold */
-#define CyCOR5		(0x14)
-#define CyCOR6		(0x18)
-#define CyCOR7		(0x07)
-#define CyRBPR		(0xcb)
-#define CyRCOR		(0xc8)
-#define CyTBPR		(0xc3)
-#define CyTCOR		(0xc0)
-#define CySCHR1		(0x1f)
-#define CySCHR2 	(0x1e)
-#define CyTPR		(0xda)
-#define CyPILR1		(0xe3)
-#define CyPILR2		(0xe0)
-#define CyPILR3		(0xe1)
-#define CyCMR		(0x1b)
-#define      CyASYNC		(0x02)
-#define CyLICR          (0x26)
-#define CyLIVR          (0x09)
-#define CySCRL		(0x23)
-#define CySCRH		(0x22)
-#define CyTFTC		(0x80)
-
-
-/* max number of chars in the FIFO */
-
-#define CyMAX_CHAR_FIFO	12
-
-/***************************************************************************/
diff --git a/include/linux/serial_8250.h b/include/linux/serial_8250.h
index a416e92..c174c90 100644
--- a/include/linux/serial_8250.h
+++ b/include/linux/serial_8250.h
@@ -65,11 +65,38 @@
  * platform device.  Using these will make your driver
  * dependent on the 8250 driver.
  */
-struct uart_port;
-struct uart_8250_port;
+
+struct uart_8250_port {
+	struct uart_port	port;
+	struct timer_list	timer;		/* "no irq" timer */
+	struct list_head	list;		/* ports on this IRQ */
+	unsigned short		capabilities;	/* port capabilities */
+	unsigned short		bugs;		/* port bugs */
+	unsigned int		tx_loadsz;	/* transmit fifo load size */
+	unsigned char		acr;
+	unsigned char		ier;
+	unsigned char		lcr;
+	unsigned char		mcr;
+	unsigned char		mcr_mask;	/* mask of user bits */
+	unsigned char		mcr_force;	/* mask of forced bits */
+	unsigned char		cur_iotype;	/* Running I/O type */
+
+	/*
+	 * Some bits in registers are cleared on a read, so they must
+	 * be saved whenever the register is read but the bits will not
+	 * be immediately processed.
+	 */
+#define LSR_SAVE_FLAGS UART_LSR_BRK_ERROR_BITS
+	unsigned char		lsr_saved_flags;
+#define MSR_SAVE_FLAGS UART_MSR_ANY_DELTA
+	unsigned char		msr_saved_flags;
+
+	/* 8250 specific callbacks */
+	int			(*dl_read)(struct uart_8250_port *);
+	void			(*dl_write)(struct uart_8250_port *, int);
+};
 
 int serial8250_register_8250_port(struct uart_8250_port *);
-int serial8250_register_port(struct uart_port *);
 void serial8250_unregister_port(int line);
 void serial8250_suspend_port(int line);
 void serial8250_resume_port(int line);
diff --git a/include/linux/serial_core.h b/include/linux/serial_core.h
index 0253c20..7cf0b68 100644
--- a/include/linux/serial_core.h
+++ b/include/linux/serial_core.h
@@ -193,8 +193,8 @@
 /* SH-SCI */
 #define PORT_SCIFB	93
 
-/* MAX3107 */
-#define PORT_MAX3107	94
+/* MAX310X */
+#define PORT_MAX310X	94
 
 /* High Speed UART for Medfield */
 #define PORT_MFD	95
diff --git a/include/linux/serial_reg.h b/include/linux/serial_reg.h
index 8ce70d7..5ed325e 100644
--- a/include/linux/serial_reg.h
+++ b/include/linux/serial_reg.h
@@ -40,6 +40,10 @@
 
 #define UART_IIR_BUSY		0x07 /* DesignWare APB Busy Detect */
 
+#define UART_IIR_RX_TIMEOUT	0x0c /* OMAP RX Timeout interrupt */
+#define UART_IIR_XOFF		0x10 /* OMAP XOFF/Special Character */
+#define UART_IIR_CTS_RTS_DSR	0x20 /* OMAP CTS/RTS/DSR Change */
+
 #define UART_FCR	2	/* Out: FIFO Control Register */
 #define UART_FCR_ENABLE_FIFO	0x01 /* Enable the FIFO */
 #define UART_FCR_CLEAR_RCVR	0x02 /* Clear the RCVR FIFO */
diff --git a/include/linux/stallion.h b/include/linux/stallion.h
deleted file mode 100644
index 336af33c..0000000
--- a/include/linux/stallion.h
+++ /dev/null
@@ -1,147 +0,0 @@
-/*****************************************************************************/
-
-/*
- *	stallion.h  -- stallion multiport serial driver.
- *
- *	Copyright (C) 1996-1998  Stallion Technologies
- *	Copyright (C) 1994-1996  Greg Ungerer.
- *
- *	This program is free software; you can redistribute it and/or modify
- *	it under the terms of the GNU General Public License as published by
- *	the Free Software Foundation; either version 2 of the License, or
- *	(at your option) any later version.
- *
- *	This program is distributed in the hope that it will be useful,
- *	but WITHOUT ANY WARRANTY; without even the implied warranty of
- *	MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *	GNU General Public License for more details.
- *
- *	You should have received a copy of the GNU General Public License
- *	along with this program; if not, write to the Free Software
- *	Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-/*****************************************************************************/
-#ifndef	_STALLION_H
-#define	_STALLION_H
-/*****************************************************************************/
-
-/*
- *	Define important driver constants here.
- */
-#define	STL_MAXBRDS		4
-#define	STL_MAXPANELS		4
-#define	STL_MAXBANKS		8
-#define	STL_PORTSPERPANEL	16
-#define	STL_MAXPORTS		64
-#define	STL_MAXDEVS		(STL_MAXBRDS * STL_MAXPORTS)
-
-
-/*
- *	Define a set of structures to hold all the board/panel/port info
- *	for our ports. These will be dynamically allocated as required.
- */
-
-/*
- *	Define a ring queue structure for each port. This will hold the
- *	TX data waiting to be output. Characters are fed into this buffer
- *	from the line discipline (or even direct from user space!) and
- *	then fed into the UARTs during interrupts. Will use a classic ring
- *	queue here for this. The good thing about this type of ring queue
- *	is that the head and tail pointers can be updated without interrupt
- *	protection - since "write" code only needs to change the head, and
- *	interrupt code only needs to change the tail.
- */
-struct stlrq {
-	char	*buf;
-	char	*head;
-	char	*tail;
-};
-
-/*
- *	Port, panel and board structures to hold status info about each.
- *	The board structure contains pointers to structures for each panel
- *	connected to it, and in turn each panel structure contains pointers
- *	for each port structure for each port on that panel. Note that
- *	the port structure also contains the board and panel number that it
- *	is associated with, this makes it (fairly) easy to get back to the
- *	board/panel info for a port.
- */
-struct stlport {
-	unsigned long		magic;
-	struct tty_port		port;
-	unsigned int		portnr;
-	unsigned int		panelnr;
-	unsigned int		brdnr;
-	int			ioaddr;
-	int			uartaddr;
-	unsigned int		pagenr;
-	unsigned long		istate;
-	int			baud_base;
-	int			custom_divisor;
-	int			close_delay;
-	int			closing_wait;
-	int			openwaitcnt;
-	int			brklen;
-	unsigned int		sigs;
-	unsigned int		rxignoremsk;
-	unsigned int		rxmarkmsk;
-	unsigned int		imr;
-	unsigned int		crenable;
-	unsigned long		clk;
-	unsigned long		hwid;
-	void			*uartp;
-	comstats_t		stats;
-	struct stlrq		tx;
-};
-
-struct stlpanel {
-	unsigned long	magic;
-	unsigned int	panelnr;
-	unsigned int	brdnr;
-	unsigned int	pagenr;
-	unsigned int	nrports;
-	int		iobase;
-	void		*uartp;
-	void		(*isr)(struct stlpanel *panelp, unsigned int iobase);
-	unsigned int	hwid;
-	unsigned int	ackmask;
-	struct stlport	*ports[STL_PORTSPERPANEL];
-};
-
-struct stlbrd {
-	unsigned long	magic;
-	unsigned int	brdnr;
-	unsigned int	brdtype;
-	unsigned int	state;
-	unsigned int	nrpanels;
-	unsigned int	nrports;
-	unsigned int	nrbnks;
-	int		irq;
-	int		irqtype;
-	int		(*isr)(struct stlbrd *brdp);
-	unsigned int	ioaddr1;
-	unsigned int	ioaddr2;
-	unsigned int	iosize1;
-	unsigned int	iosize2;
-	unsigned int	iostatus;
-	unsigned int	ioctrl;
-	unsigned int	ioctrlval;
-	unsigned int	hwid;
-	unsigned long	clk;
-	unsigned int	bnkpageaddr[STL_MAXBANKS];
-	unsigned int	bnkstataddr[STL_MAXBANKS];
-	struct stlpanel	*bnk2panel[STL_MAXBANKS];
-	struct stlpanel	*panels[STL_MAXPANELS];
-};
-
-
-/*
- *	Define MAGIC numbers used for above structures.
- */
-#define	STL_PORTMAGIC	0x5a7182c9
-#define	STL_PANELMAGIC	0x7ef621a1
-#define	STL_BOARDMAGIC	0xa2267f52
-
-/*****************************************************************************/
-#endif
diff --git a/include/linux/time.h b/include/linux/time.h
index c81c5e4..b51e664 100644
--- a/include/linux/time.h
+++ b/include/linux/time.h
@@ -107,11 +107,36 @@
 	return ts_delta;
 }
 
+#define KTIME_MAX			((s64)~((u64)1 << 63))
+#if (BITS_PER_LONG == 64)
+# define KTIME_SEC_MAX			(KTIME_MAX / NSEC_PER_SEC)
+#else
+# define KTIME_SEC_MAX			LONG_MAX
+#endif
+
 /*
  * Returns true if the timespec is norm, false if denorm:
  */
-#define timespec_valid(ts) \
-	(((ts)->tv_sec >= 0) && (((unsigned long) (ts)->tv_nsec) < NSEC_PER_SEC))
+static inline bool timespec_valid(const struct timespec *ts)
+{
+	/* Dates before 1970 are bogus */
+	if (ts->tv_sec < 0)
+		return false;
+	/* Can't have more nanoseconds then a second */
+	if ((unsigned long)ts->tv_nsec >= NSEC_PER_SEC)
+		return false;
+	return true;
+}
+
+static inline bool timespec_valid_strict(const struct timespec *ts)
+{
+	if (!timespec_valid(ts))
+		return false;
+	/* Disallow values that could overflow ktime_t */
+	if ((unsigned long long)ts->tv_sec >= KTIME_SEC_MAX)
+		return false;
+	return true;
+}
 
 extern void read_persistent_clock(struct timespec *ts);
 extern void read_boot_clock(struct timespec *ts);
diff --git a/include/linux/tty.h b/include/linux/tty.h
index 9f47ab5..1509b86 100644
--- a/include/linux/tty.h
+++ b/include/linux/tty.h
@@ -43,6 +43,7 @@
 #include <linux/tty_driver.h>
 #include <linux/tty_ldisc.h>
 #include <linux/mutex.h>
+#include <linux/tty_flags.h>
 
 
 
@@ -103,28 +104,28 @@
 #define TTY_PARITY	3
 #define TTY_OVERRUN	4
 
-#define INTR_CHAR(tty) ((tty)->termios->c_cc[VINTR])
-#define QUIT_CHAR(tty) ((tty)->termios->c_cc[VQUIT])
-#define ERASE_CHAR(tty) ((tty)->termios->c_cc[VERASE])
-#define KILL_CHAR(tty) ((tty)->termios->c_cc[VKILL])
-#define EOF_CHAR(tty) ((tty)->termios->c_cc[VEOF])
-#define TIME_CHAR(tty) ((tty)->termios->c_cc[VTIME])
-#define MIN_CHAR(tty) ((tty)->termios->c_cc[VMIN])
-#define SWTC_CHAR(tty) ((tty)->termios->c_cc[VSWTC])
-#define START_CHAR(tty) ((tty)->termios->c_cc[VSTART])
-#define STOP_CHAR(tty) ((tty)->termios->c_cc[VSTOP])
-#define SUSP_CHAR(tty) ((tty)->termios->c_cc[VSUSP])
-#define EOL_CHAR(tty) ((tty)->termios->c_cc[VEOL])
-#define REPRINT_CHAR(tty) ((tty)->termios->c_cc[VREPRINT])
-#define DISCARD_CHAR(tty) ((tty)->termios->c_cc[VDISCARD])
-#define WERASE_CHAR(tty) ((tty)->termios->c_cc[VWERASE])
-#define LNEXT_CHAR(tty)	((tty)->termios->c_cc[VLNEXT])
-#define EOL2_CHAR(tty) ((tty)->termios->c_cc[VEOL2])
+#define INTR_CHAR(tty) ((tty)->termios.c_cc[VINTR])
+#define QUIT_CHAR(tty) ((tty)->termios.c_cc[VQUIT])
+#define ERASE_CHAR(tty) ((tty)->termios.c_cc[VERASE])
+#define KILL_CHAR(tty) ((tty)->termios.c_cc[VKILL])
+#define EOF_CHAR(tty) ((tty)->termios.c_cc[VEOF])
+#define TIME_CHAR(tty) ((tty)->termios.c_cc[VTIME])
+#define MIN_CHAR(tty) ((tty)->termios.c_cc[VMIN])
+#define SWTC_CHAR(tty) ((tty)->termios.c_cc[VSWTC])
+#define START_CHAR(tty) ((tty)->termios.c_cc[VSTART])
+#define STOP_CHAR(tty) ((tty)->termios.c_cc[VSTOP])
+#define SUSP_CHAR(tty) ((tty)->termios.c_cc[VSUSP])
+#define EOL_CHAR(tty) ((tty)->termios.c_cc[VEOL])
+#define REPRINT_CHAR(tty) ((tty)->termios.c_cc[VREPRINT])
+#define DISCARD_CHAR(tty) ((tty)->termios.c_cc[VDISCARD])
+#define WERASE_CHAR(tty) ((tty)->termios.c_cc[VWERASE])
+#define LNEXT_CHAR(tty)	((tty)->termios.c_cc[VLNEXT])
+#define EOL2_CHAR(tty) ((tty)->termios.c_cc[VEOL2])
 
-#define _I_FLAG(tty, f)	((tty)->termios->c_iflag & (f))
-#define _O_FLAG(tty, f)	((tty)->termios->c_oflag & (f))
-#define _C_FLAG(tty, f)	((tty)->termios->c_cflag & (f))
-#define _L_FLAG(tty, f)	((tty)->termios->c_lflag & (f))
+#define _I_FLAG(tty, f)	((tty)->termios.c_iflag & (f))
+#define _O_FLAG(tty, f)	((tty)->termios.c_oflag & (f))
+#define _C_FLAG(tty, f)	((tty)->termios.c_cflag & (f))
+#define _L_FLAG(tty, f)	((tty)->termios.c_lflag & (f))
 
 #define I_IGNBRK(tty)	_I_FLAG((tty), IGNBRK)
 #define I_BRKINT(tty)	_I_FLAG((tty), BRKINT)
@@ -268,10 +269,11 @@
 	struct mutex ldisc_mutex;
 	struct tty_ldisc *ldisc;
 
+	struct mutex legacy_mutex;
 	struct mutex termios_mutex;
 	spinlock_t ctrl_lock;
 	/* Termios values are protected by the termios mutex */
-	struct ktermios *termios, *termios_locked;
+	struct ktermios termios, termios_locked;
 	struct termiox *termiox;	/* May be NULL for unsupported */
 	char name[64];
 	struct pid *pgrp;		/* Protected by ctrl lock */
@@ -410,6 +412,10 @@
 extern int tty_unregister_driver(struct tty_driver *driver);
 extern struct device *tty_register_device(struct tty_driver *driver,
 					  unsigned index, struct device *dev);
+extern struct device *tty_register_device_attr(struct tty_driver *driver,
+				unsigned index, struct device *device,
+				void *drvdata,
+				const struct attribute_group **attr_grp);
 extern void tty_unregister_device(struct tty_driver *driver, unsigned index);
 extern int tty_read_raw_data(struct tty_struct *tty, unsigned char *bufp,
 			     int buflen);
@@ -423,7 +429,6 @@
 extern int tty_do_resize(struct tty_struct *tty, struct winsize *ws);
 extern void tty_driver_remove_tty(struct tty_driver *driver,
 				  struct tty_struct *tty);
-extern void tty_shutdown(struct tty_struct *tty);
 extern void tty_free_termios(struct tty_struct *tty);
 extern int is_current_pgrp_orphaned(void);
 extern struct pid *tty_get_pgrp(struct tty_struct *tty);
@@ -497,6 +502,15 @@
 #define tty_is_writelocked(tty)  (mutex_is_locked(&tty->atomic_write_lock))
 
 extern void tty_port_init(struct tty_port *port);
+extern void tty_port_link_device(struct tty_port *port,
+		struct tty_driver *driver, unsigned index);
+extern struct device *tty_port_register_device(struct tty_port *port,
+		struct tty_driver *driver, unsigned index,
+		struct device *device);
+extern struct device *tty_port_register_device_attr(struct tty_port *port,
+		struct tty_driver *driver, unsigned index,
+		struct device *device, void *drvdata,
+		const struct attribute_group **attr_grp);
 extern int tty_port_alloc_xmit_buf(struct tty_port *port);
 extern void tty_port_free_xmit_buf(struct tty_port *port);
 extern void tty_port_put(struct tty_port *port);
@@ -508,6 +522,12 @@
 	return port;
 }
 
+/* If the cts flow control is enabled, return true. */
+static inline bool tty_port_cts_enabled(struct tty_port *port)
+{
+	return port->flags & ASYNC_CTS_FLOW;
+}
+
 extern struct tty_struct *tty_port_tty_get(struct tty_port *port);
 extern void tty_port_tty_set(struct tty_port *port, struct tty_struct *tty);
 extern int tty_port_carrier_raised(struct tty_port *port);
@@ -521,6 +541,8 @@
 extern void tty_port_close_end(struct tty_port *port, struct tty_struct *tty);
 extern void tty_port_close(struct tty_port *port,
 				struct tty_struct *tty, struct file *filp);
+extern int tty_port_install(struct tty_port *port, struct tty_driver *driver,
+				struct tty_struct *tty);
 extern int tty_port_open(struct tty_port *port,
 				struct tty_struct *tty, struct file *filp);
 static inline int tty_port_users(struct tty_port *port)
@@ -605,8 +627,12 @@
 
 /* tty_mutex.c */
 /* functions for preparation of BKL removal */
-extern void __lockfunc tty_lock(void) __acquires(tty_lock);
-extern void __lockfunc tty_unlock(void) __releases(tty_lock);
+extern void __lockfunc tty_lock(struct tty_struct *tty);
+extern void __lockfunc tty_unlock(struct tty_struct *tty);
+extern void __lockfunc tty_lock_pair(struct tty_struct *tty,
+				struct tty_struct *tty2);
+extern void __lockfunc tty_unlock_pair(struct tty_struct *tty,
+				struct tty_struct *tty2);
 
 /*
  * this shall be called only from where BTM is held (like close)
@@ -621,9 +647,9 @@
 static inline void tty_wait_until_sent_from_close(struct tty_struct *tty,
 		long timeout)
 {
-	tty_unlock(); /* tty->ops->close holds the BTM, drop it while waiting */
+	tty_unlock(tty); /* tty->ops->close holds the BTM, drop it while waiting */
 	tty_wait_until_sent(tty, timeout);
-	tty_lock();
+	tty_lock(tty);
 }
 
 /*
@@ -638,16 +664,16 @@
  *
  * Do not use in new code.
  */
-#define wait_event_interruptible_tty(wq, condition)			\
+#define wait_event_interruptible_tty(tty, wq, condition)		\
 ({									\
 	int __ret = 0;							\
 	if (!(condition)) {						\
-		__wait_event_interruptible_tty(wq, condition, __ret);	\
+		__wait_event_interruptible_tty(tty, wq, condition, __ret);	\
 	}								\
 	__ret;								\
 })
 
-#define __wait_event_interruptible_tty(wq, condition, ret)		\
+#define __wait_event_interruptible_tty(tty, wq, condition, ret)		\
 do {									\
 	DEFINE_WAIT(__wait);						\
 									\
@@ -656,9 +682,9 @@
 		if (condition)						\
 			break;						\
 		if (!signal_pending(current)) {				\
-			tty_unlock();					\
+			tty_unlock(tty);					\
 			schedule();					\
-			tty_lock();					\
+			tty_lock(tty);					\
 			continue;					\
 		}							\
 		ret = -ERESTARTSYS;					\
diff --git a/include/linux/tty_driver.h b/include/linux/tty_driver.h
index 6e6dbb7..dd976cf 100644
--- a/include/linux/tty_driver.h
+++ b/include/linux/tty_driver.h
@@ -45,14 +45,9 @@
  *
  * void (*shutdown)(struct tty_struct * tty);
  *
- * 	This routine is called synchronously when a particular tty device
- *	is closed for the last time freeing up the resources.
- *	Note that tty_shutdown() is not called if ops->shutdown is defined.
- *	This means one is responsible to take care of calling ops->remove (e.g.
- *	via tty_driver_remove_tty) and releasing tty->termios.
- *	Note that this hook may be called from *all* the contexts where one
- *	uses tty refcounting (e.g. tty_port_tty_get).
- *
+ * 	This routine is called under the tty lock when a particular tty device
+ *	is closed for the last time. It executes before the tty resources
+ *	are freed so may execute while another function holds a tty kref.
  *
  * void (*cleanup)(struct tty_struct * tty);
  *
@@ -294,18 +289,18 @@
 struct tty_driver {
 	int	magic;		/* magic number for this structure */
 	struct kref kref;	/* Reference management */
-	struct cdev cdev;
+	struct cdev *cdevs;
 	struct module	*owner;
 	const char	*driver_name;
 	const char	*name;
 	int	name_base;	/* offset of printed name */
 	int	major;		/* major device number */
 	int	minor_start;	/* start of minor device number */
-	int	num;		/* number of devices allocated */
+	unsigned int	num;	/* number of devices allocated */
 	short	type;		/* type of tty driver */
 	short	subtype;	/* subtype of tty driver */
 	struct ktermios init_termios; /* Initial termios */
-	int	flags;		/* tty driver flags */
+	unsigned long	flags;		/* tty driver flags */
 	struct proc_dir_entry *proc_entry; /* /proc fs entry */
 	struct tty_driver *other; /* only used for the PTY driver */
 
@@ -313,6 +308,7 @@
 	 * Pointer to the tty data structures
 	 */
 	struct tty_struct **ttys;
+	struct tty_port **ports;
 	struct ktermios **termios;
 	void *driver_state;
 
@@ -326,7 +322,8 @@
 
 extern struct list_head tty_drivers;
 
-extern struct tty_driver *__alloc_tty_driver(int lines, struct module *owner);
+extern struct tty_driver *__tty_alloc_driver(unsigned int lines,
+		struct module *owner, unsigned long flags);
 extern void put_tty_driver(struct tty_driver *driver);
 extern void tty_set_operations(struct tty_driver *driver,
 			const struct tty_operations *op);
@@ -334,7 +331,21 @@
 
 extern void tty_driver_kref_put(struct tty_driver *driver);
 
-#define alloc_tty_driver(lines) __alloc_tty_driver(lines, THIS_MODULE)
+/* Use TTY_DRIVER_* flags below */
+#define tty_alloc_driver(lines, flags) \
+		__tty_alloc_driver(lines, THIS_MODULE, flags)
+
+/*
+ * DEPRECATED Do not use this in new code, use tty_alloc_driver instead.
+ * (And change the return value checks.)
+ */
+static inline struct tty_driver *alloc_tty_driver(unsigned int lines)
+{
+	struct tty_driver *ret = tty_alloc_driver(lines, 0);
+	if (IS_ERR(ret))
+		return NULL;
+	return ret;
+}
 
 static inline struct tty_driver *tty_driver_kref_get(struct tty_driver *d)
 {
@@ -380,6 +391,14 @@
  *	the requested timeout to the caller instead of using a simple
  *	on/off interface.
  *
+ * TTY_DRIVER_DYNAMIC_ALLOC -- do not allocate structures which are
+ *	needed per line for this driver as it would waste memory.
+ *	The driver will take care.
+ *
+ * TTY_DRIVER_UNNUMBERED_NODE -- do not create numbered /dev nodes. In
+ *	other words create /dev/ttyprintk and not /dev/ttyprintk0.
+ *	Applicable only when a driver for a single tty device is
+ *	being allocated.
  */
 #define TTY_DRIVER_INSTALLED		0x0001
 #define TTY_DRIVER_RESET_TERMIOS	0x0002
@@ -387,6 +406,8 @@
 #define TTY_DRIVER_DYNAMIC_DEV		0x0008
 #define TTY_DRIVER_DEVPTS_MEM		0x0010
 #define TTY_DRIVER_HARDWARE_BREAK	0x0020
+#define TTY_DRIVER_DYNAMIC_ALLOC	0x0040
+#define TTY_DRIVER_UNNUMBERED_NODE	0x0080
 
 /* tty driver types */
 #define TTY_DRIVER_TYPE_SYSTEM		0x0001
diff --git a/include/linux/tty_flags.h b/include/linux/tty_flags.h
new file mode 100644
index 0000000..eefcb48
--- /dev/null
+++ b/include/linux/tty_flags.h
@@ -0,0 +1,78 @@
+#ifndef _LINUX_TTY_FLAGS_H
+#define _LINUX_TTY_FLAGS_H
+
+/*
+ * Definitions for async_struct (and serial_struct) flags field also
+ * shared by the tty_port flags structures.
+ *
+ * Define ASYNCB_* for convenient use with {test,set,clear}_bit.
+ */
+#define ASYNCB_HUP_NOTIFY	 0 /* Notify getty on hangups and closes
+				    * on the callout port */
+#define ASYNCB_FOURPORT		 1 /* Set OU1, OUT2 per AST Fourport settings */
+#define ASYNCB_SAK		 2 /* Secure Attention Key (Orange book) */
+#define ASYNCB_SPLIT_TERMIOS	 3 /* Separate termios for dialin/callout */
+#define ASYNCB_SPD_HI		 4 /* Use 56000 instead of 38400 bps */
+#define ASYNCB_SPD_VHI		 5 /* Use 115200 instead of 38400 bps */
+#define ASYNCB_SKIP_TEST	 6 /* Skip UART test during autoconfiguration */
+#define ASYNCB_AUTO_IRQ		 7 /* Do automatic IRQ during
+				    * autoconfiguration */
+#define ASYNCB_SESSION_LOCKOUT	 8 /* Lock out cua opens based on session */
+#define ASYNCB_PGRP_LOCKOUT	 9 /* Lock out cua opens based on pgrp */
+#define ASYNCB_CALLOUT_NOHUP	10 /* Don't do hangups for cua device */
+#define ASYNCB_HARDPPS_CD	11 /* Call hardpps when CD goes high  */
+#define ASYNCB_SPD_SHI		12 /* Use 230400 instead of 38400 bps */
+#define ASYNCB_LOW_LATENCY	13 /* Request low latency behaviour */
+#define ASYNCB_BUGGY_UART	14 /* This is a buggy UART, skip some safety
+				    * checks.  Note: can be dangerous! */
+#define ASYNCB_AUTOPROBE	15 /* Port was autoprobed by PCI or PNP code */
+#define ASYNCB_LAST_USER	15
+
+/* Internal flags used only by kernel */
+#define ASYNCB_INITIALIZED	31 /* Serial port was initialized */
+#define ASYNCB_SUSPENDED	30 /* Serial port is suspended */
+#define ASYNCB_NORMAL_ACTIVE	29 /* Normal device is active */
+#define ASYNCB_BOOT_AUTOCONF	28 /* Autoconfigure port on bootup */
+#define ASYNCB_CLOSING		27 /* Serial port is closing */
+#define ASYNCB_CTS_FLOW		26 /* Do CTS flow control */
+#define ASYNCB_CHECK_CD		25 /* i.e., CLOCAL */
+#define ASYNCB_SHARE_IRQ	24 /* for multifunction cards, no longer used */
+#define ASYNCB_CONS_FLOW	23 /* flow control for console  */
+#define ASYNCB_FIRST_KERNEL	22
+
+#define ASYNC_HUP_NOTIFY	(1U << ASYNCB_HUP_NOTIFY)
+#define ASYNC_SUSPENDED		(1U << ASYNCB_SUSPENDED)
+#define ASYNC_FOURPORT		(1U << ASYNCB_FOURPORT)
+#define ASYNC_SAK		(1U << ASYNCB_SAK)
+#define ASYNC_SPLIT_TERMIOS	(1U << ASYNCB_SPLIT_TERMIOS)
+#define ASYNC_SPD_HI		(1U << ASYNCB_SPD_HI)
+#define ASYNC_SPD_VHI		(1U << ASYNCB_SPD_VHI)
+#define ASYNC_SKIP_TEST		(1U << ASYNCB_SKIP_TEST)
+#define ASYNC_AUTO_IRQ		(1U << ASYNCB_AUTO_IRQ)
+#define ASYNC_SESSION_LOCKOUT	(1U << ASYNCB_SESSION_LOCKOUT)
+#define ASYNC_PGRP_LOCKOUT	(1U << ASYNCB_PGRP_LOCKOUT)
+#define ASYNC_CALLOUT_NOHUP	(1U << ASYNCB_CALLOUT_NOHUP)
+#define ASYNC_HARDPPS_CD	(1U << ASYNCB_HARDPPS_CD)
+#define ASYNC_SPD_SHI		(1U << ASYNCB_SPD_SHI)
+#define ASYNC_LOW_LATENCY	(1U << ASYNCB_LOW_LATENCY)
+#define ASYNC_BUGGY_UART	(1U << ASYNCB_BUGGY_UART)
+#define ASYNC_AUTOPROBE		(1U << ASYNCB_AUTOPROBE)
+
+#define ASYNC_FLAGS		((1U << (ASYNCB_LAST_USER + 1)) - 1)
+#define ASYNC_USR_MASK		(ASYNC_SPD_MASK|ASYNC_CALLOUT_NOHUP| \
+		ASYNC_LOW_LATENCY)
+#define ASYNC_SPD_CUST		(ASYNC_SPD_HI|ASYNC_SPD_VHI)
+#define ASYNC_SPD_WARP		(ASYNC_SPD_HI|ASYNC_SPD_SHI)
+#define ASYNC_SPD_MASK		(ASYNC_SPD_HI|ASYNC_SPD_VHI|ASYNC_SPD_SHI)
+
+#define ASYNC_INITIALIZED	(1U << ASYNCB_INITIALIZED)
+#define ASYNC_NORMAL_ACTIVE	(1U << ASYNCB_NORMAL_ACTIVE)
+#define ASYNC_BOOT_AUTOCONF	(1U << ASYNCB_BOOT_AUTOCONF)
+#define ASYNC_CLOSING		(1U << ASYNCB_CLOSING)
+#define ASYNC_CTS_FLOW		(1U << ASYNCB_CTS_FLOW)
+#define ASYNC_CHECK_CD		(1U << ASYNCB_CHECK_CD)
+#define ASYNC_SHARE_IRQ		(1U << ASYNCB_SHARE_IRQ)
+#define ASYNC_CONS_FLOW		(1U << ASYNCB_CONS_FLOW)
+#define ASYNC_INTERNAL_FLAGS	(~((1U << ASYNCB_FIRST_KERNEL) - 1))
+
+#endif
diff --git a/include/net/irda/ircomm_tty.h b/include/net/irda/ircomm_tty.h
index 59ba38bc..80ffde3 100644
--- a/include/net/irda/ircomm_tty.h
+++ b/include/net/irda/ircomm_tty.h
@@ -52,21 +52,16 @@
 /* Same for payload size. See qos.c for the smallest max data size */
 #define IRCOMM_TTY_DATA_UNINITIALISED	(64 - IRCOMM_TTY_HDR_UNINITIALISED)
 
-/* Those are really defined in include/linux/serial.h - Jean II */
-#define ASYNC_B_INITIALIZED	31	/* Serial port was initialized */
-#define ASYNC_B_NORMAL_ACTIVE	29	/* Normal device is active */
-#define ASYNC_B_CLOSING		27	/* Serial port is closing */
-
 /*
  * IrCOMM TTY driver state
  */
 struct ircomm_tty_cb {
 	irda_queue_t queue;            /* Must be first */
+	struct tty_port port;
 	magic_t magic;
 
 	int state;                /* Connect state */
 
-	struct tty_struct *tty;
 	struct ircomm_cb *ircomm; /* IrCOMM layer instance */
 
 	struct sk_buff *tx_skb;   /* Transmit buffer */
@@ -80,7 +75,6 @@
 	LOCAL_FLOW flow;          /* IrTTP flow status */
 
 	int line;
-	unsigned long flags;
 
 	__u8 dlsap_sel;
 	__u8 slsap_sel;
@@ -97,19 +91,10 @@
 	void *skey;
 	void *ckey;
 
-	wait_queue_head_t open_wait;
-	wait_queue_head_t close_wait;
 	struct timer_list watchdog_timer;
 	struct work_struct  tqueue;
 
-        unsigned short    close_delay;
-        unsigned short    closing_wait; /* time to wait before closing */
-
-	int  open_count;
-	int  blocked_open;	/* # of blocked opens */
-
 	/* Protect concurent access to :
-	 *	o self->open_count
 	 *	o self->ctrl_skb
 	 *	o self->tx_skb
 	 * Maybe other things may gain to be protected as well...
diff --git a/include/net/netfilter/nf_conntrack_ecache.h b/include/net/netfilter/nf_conntrack_ecache.h
index e1ce104..4a045cd 100644
--- a/include/net/netfilter/nf_conntrack_ecache.h
+++ b/include/net/netfilter/nf_conntrack_ecache.h
@@ -18,6 +18,7 @@
 	u16 ctmask;		/* bitmask of ct events to be delivered */
 	u16 expmask;		/* bitmask of expect events to be delivered */
 	u32 pid;		/* netlink pid of destroyer */
+	struct timer_list timeout;
 };
 
 static inline struct nf_conntrack_ecache *
diff --git a/include/xen/events.h b/include/xen/events.h
index 9c641de..04399b2 100644
--- a/include/xen/events.h
+++ b/include/xen/events.h
@@ -58,8 +58,6 @@
 
 void xen_irq_resume(void);
 
-void xen_hvm_prepare_kexec(struct shared_info *sip, unsigned long pfn);
-
 /* Clear an irq's pending state, in preparation for polling on it */
 void xen_clear_irq_pending(int irq);
 void xen_set_irq_pending(int irq);
diff --git a/kernel/fork.c b/kernel/fork.c
index 3bd2280..2c8857e 100644
--- a/kernel/fork.c
+++ b/kernel/fork.c
@@ -455,8 +455,8 @@
 		if (retval)
 			goto out;
 
-		if (file && uprobe_mmap(tmp))
-			goto out;
+		if (file)
+			uprobe_mmap(tmp);
 	}
 	/* a new mm has just been created */
 	arch_dup_mmap(oldmm, mm);
diff --git a/kernel/time/timekeeping.c b/kernel/time/timekeeping.c
index e16af19..34e5eac 100644
--- a/kernel/time/timekeeping.c
+++ b/kernel/time/timekeeping.c
@@ -115,6 +115,7 @@
 {
 	tk->xtime_sec += ts->tv_sec;
 	tk->xtime_nsec += (u64)ts->tv_nsec << tk->shift;
+	tk_normalize_xtime(tk);
 }
 
 static void tk_set_wall_to_mono(struct timekeeper *tk, struct timespec wtm)
@@ -276,7 +277,7 @@
 	tk->xtime_nsec += cycle_delta * tk->mult;
 
 	/* If arch requires, add in gettimeoffset() */
-	tk->xtime_nsec += arch_gettimeoffset() << tk->shift;
+	tk->xtime_nsec += (u64)arch_gettimeoffset() << tk->shift;
 
 	tk_normalize_xtime(tk);
 
@@ -427,7 +428,7 @@
 	struct timespec ts_delta, xt;
 	unsigned long flags;
 
-	if ((unsigned long)tv->tv_nsec >= NSEC_PER_SEC)
+	if (!timespec_valid_strict(tv))
 		return -EINVAL;
 
 	write_seqlock_irqsave(&tk->lock, flags);
@@ -463,6 +464,8 @@
 {
 	struct timekeeper *tk = &timekeeper;
 	unsigned long flags;
+	struct timespec tmp;
+	int ret = 0;
 
 	if ((unsigned long)ts->tv_nsec >= NSEC_PER_SEC)
 		return -EINVAL;
@@ -471,10 +474,17 @@
 
 	timekeeping_forward_now(tk);
 
+	/* Make sure the proposed value is valid */
+	tmp = timespec_add(tk_xtime(tk),  *ts);
+	if (!timespec_valid_strict(&tmp)) {
+		ret = -EINVAL;
+		goto error;
+	}
 
 	tk_xtime_add(tk, ts);
 	tk_set_wall_to_mono(tk, timespec_sub(tk->wall_to_monotonic, *ts));
 
+error: /* even if we error out, we forwarded the time, so call update */
 	timekeeping_update(tk, true);
 
 	write_sequnlock_irqrestore(&tk->lock, flags);
@@ -482,7 +492,7 @@
 	/* signal hrtimers about time change */
 	clock_was_set();
 
-	return 0;
+	return ret;
 }
 EXPORT_SYMBOL(timekeeping_inject_offset);
 
@@ -649,7 +659,20 @@
 	struct timespec now, boot, tmp;
 
 	read_persistent_clock(&now);
+	if (!timespec_valid_strict(&now)) {
+		pr_warn("WARNING: Persistent clock returned invalid value!\n"
+			"         Check your CMOS/BIOS settings.\n");
+		now.tv_sec = 0;
+		now.tv_nsec = 0;
+	}
+
 	read_boot_clock(&boot);
+	if (!timespec_valid_strict(&boot)) {
+		pr_warn("WARNING: Boot clock returned invalid value!\n"
+			"         Check your CMOS/BIOS settings.\n");
+		boot.tv_sec = 0;
+		boot.tv_nsec = 0;
+	}
 
 	seqlock_init(&tk->lock);
 
@@ -690,7 +713,7 @@
 static void __timekeeping_inject_sleeptime(struct timekeeper *tk,
 							struct timespec *delta)
 {
-	if (!timespec_valid(delta)) {
+	if (!timespec_valid_strict(delta)) {
 		printk(KERN_WARNING "__timekeeping_inject_sleeptime: Invalid "
 					"sleep delta value!\n");
 		return;
@@ -1129,6 +1152,10 @@
 	offset = (clock->read(clock) - clock->cycle_last) & clock->mask;
 #endif
 
+	/* Check if there's really nothing to do */
+	if (offset < tk->cycle_interval)
+		goto out;
+
 	/*
 	 * With NO_HZ we may have to accumulate many cycle_intervals
 	 * (think "ticks") worth of time at once. To do this efficiently,
@@ -1161,9 +1188,9 @@
 	* the vsyscall implementations are converted to use xtime_nsec
 	* (shifted nanoseconds), this can be killed.
 	*/
-	remainder = tk->xtime_nsec & ((1 << tk->shift) - 1);
+	remainder = tk->xtime_nsec & ((1ULL << tk->shift) - 1);
 	tk->xtime_nsec -= remainder;
-	tk->xtime_nsec += 1 << tk->shift;
+	tk->xtime_nsec += 1ULL << tk->shift;
 	tk->ntp_error += remainder << tk->ntp_error_shift;
 
 	/*
diff --git a/kernel/trace/trace_syscalls.c b/kernel/trace/trace_syscalls.c
index 60e4d78..6b245f64 100644
--- a/kernel/trace/trace_syscalls.c
+++ b/kernel/trace/trace_syscalls.c
@@ -506,6 +506,8 @@
 	int size;
 
 	syscall_nr = syscall_get_nr(current, regs);
+	if (syscall_nr < 0)
+		return;
 	if (!test_bit(syscall_nr, enabled_perf_enter_syscalls))
 		return;
 
@@ -580,6 +582,8 @@
 	int size;
 
 	syscall_nr = syscall_get_nr(current, regs);
+	if (syscall_nr < 0)
+		return;
 	if (!test_bit(syscall_nr, enabled_perf_exit_syscalls))
 		return;
 
diff --git a/mm/filemap.c b/mm/filemap.c
index fa5ca30..3843445 100644
--- a/mm/filemap.c
+++ b/mm/filemap.c
@@ -1412,12 +1412,8 @@
 			retval = filemap_write_and_wait_range(mapping, pos,
 					pos + iov_length(iov, nr_segs) - 1);
 			if (!retval) {
-				struct blk_plug plug;
-
-				blk_start_plug(&plug);
 				retval = mapping->a_ops->direct_IO(READ, iocb,
 							iov, pos, nr_segs);
-				blk_finish_plug(&plug);
 			}
 			if (retval > 0) {
 				*ppos = pos + retval;
@@ -2527,14 +2523,12 @@
 {
 	struct file *file = iocb->ki_filp;
 	struct inode *inode = file->f_mapping->host;
-	struct blk_plug plug;
 	ssize_t ret;
 
 	BUG_ON(iocb->ki_pos != pos);
 
 	sb_start_write(inode->i_sb);
 	mutex_lock(&inode->i_mutex);
-	blk_start_plug(&plug);
 	ret = __generic_file_aio_write(iocb, iov, nr_segs, &iocb->ki_pos);
 	mutex_unlock(&inode->i_mutex);
 
@@ -2545,7 +2539,6 @@
 		if (err < 0 && ret > 0)
 			ret = err;
 	}
-	blk_finish_plug(&plug);
 	sb_end_write(inode->i_sb);
 	return ret;
 }
diff --git a/mm/mempolicy.c b/mm/mempolicy.c
index bd92431..4ada3be 100644
--- a/mm/mempolicy.c
+++ b/mm/mempolicy.c
@@ -2562,7 +2562,7 @@
 		break;
 
 	default:
-		BUG();
+		return -EINVAL;
 	}
 
 	l = strlen(policy_modes[mode]);
diff --git a/mm/mmap.c b/mm/mmap.c
index 9adee9f..ae18a48 100644
--- a/mm/mmap.c
+++ b/mm/mmap.c
@@ -1356,9 +1356,8 @@
 	} else if ((flags & MAP_POPULATE) && !(flags & MAP_NONBLOCK))
 		make_pages_present(addr, addr + len);
 
-	if (file && uprobe_mmap(vma))
-		/* matching probes but cannot insert */
-		goto unmap_and_free_vma;
+	if (file)
+		uprobe_mmap(vma);
 
 	return addr;
 
diff --git a/mm/slab.c b/mm/slab.c
index f8b0d53..811af03 100644
--- a/mm/slab.c
+++ b/mm/slab.c
@@ -3260,6 +3260,7 @@
 
 		/* cache_grow can reenable interrupts, then ac could change. */
 		ac = cpu_cache_get(cachep);
+		node = numa_mem_id();
 
 		/* no objects in sight? abort */
 		if (!x && (ac->avail == 0 || force_refill))
diff --git a/net/bluetooth/rfcomm/tty.c b/net/bluetooth/rfcomm/tty.c
index 56f1823..ccc2487 100644
--- a/net/bluetooth/rfcomm/tty.c
+++ b/net/bluetooth/rfcomm/tty.c
@@ -278,8 +278,8 @@
 	if (err < 0)
 		goto free;
 
-	dev->tty_dev = tty_register_device(rfcomm_tty_driver, dev->id, NULL);
-
+	dev->tty_dev = tty_port_register_device(&dev->port, rfcomm_tty_driver,
+			dev->id, NULL);
 	if (IS_ERR(dev->tty_dev)) {
 		err = PTR_ERR(dev->tty_dev);
 		list_del(&dev->list);
@@ -705,9 +705,9 @@
 			break;
 		}
 
-		tty_unlock();
+		tty_unlock(tty);
 		schedule();
-		tty_lock();
+		tty_lock(tty);
 	}
 	set_current_state(TASK_RUNNING);
 	remove_wait_queue(&dev->wait, &wait);
@@ -861,7 +861,7 @@
 
 static void rfcomm_tty_set_termios(struct tty_struct *tty, struct ktermios *old)
 {
-	struct ktermios *new = tty->termios;
+	struct ktermios *new = &tty->termios;
 	int old_baud_rate = tty_termios_baud_rate(old);
 	int new_baud_rate = tty_termios_baud_rate(new);
 
diff --git a/net/core/netpoll.c b/net/core/netpoll.c
index 346b1eb..e4ba3e7 100644
--- a/net/core/netpoll.c
+++ b/net/core/netpoll.c
@@ -168,24 +168,16 @@
 	struct napi_struct *napi;
 	int budget = 16;
 
-	WARN_ON_ONCE(!irqs_disabled());
-
 	list_for_each_entry(napi, &dev->napi_list, dev_list) {
-		local_irq_enable();
 		if (napi->poll_owner != smp_processor_id() &&
 		    spin_trylock(&napi->poll_lock)) {
-			rcu_read_lock_bh();
 			budget = poll_one_napi(rcu_dereference_bh(dev->npinfo),
 					       napi, budget);
-			rcu_read_unlock_bh();
 			spin_unlock(&napi->poll_lock);
 
-			if (!budget) {
-				local_irq_disable();
+			if (!budget)
 				break;
-			}
 		}
-		local_irq_disable();
 	}
 }
 
diff --git a/net/ipv4/ipmr.c b/net/ipv4/ipmr.c
index 8eec8f4..ebdf06f 100644
--- a/net/ipv4/ipmr.c
+++ b/net/ipv4/ipmr.c
@@ -124,6 +124,8 @@
 static struct kmem_cache *mrt_cachep __read_mostly;
 
 static struct mr_table *ipmr_new_table(struct net *net, u32 id);
+static void ipmr_free_table(struct mr_table *mrt);
+
 static int ip_mr_forward(struct net *net, struct mr_table *mrt,
 			 struct sk_buff *skb, struct mfc_cache *cache,
 			 int local);
@@ -131,6 +133,7 @@
 			     struct sk_buff *pkt, vifi_t vifi, int assert);
 static int __ipmr_fill_mroute(struct mr_table *mrt, struct sk_buff *skb,
 			      struct mfc_cache *c, struct rtmsg *rtm);
+static void mroute_clean_tables(struct mr_table *mrt);
 static void ipmr_expire_process(unsigned long arg);
 
 #ifdef CONFIG_IP_MROUTE_MULTIPLE_TABLES
@@ -271,7 +274,7 @@
 
 	list_for_each_entry_safe(mrt, next, &net->ipv4.mr_tables, list) {
 		list_del(&mrt->list);
-		kfree(mrt);
+		ipmr_free_table(mrt);
 	}
 	fib_rules_unregister(net->ipv4.mr_rules_ops);
 }
@@ -299,7 +302,7 @@
 
 static void __net_exit ipmr_rules_exit(struct net *net)
 {
-	kfree(net->ipv4.mrt);
+	ipmr_free_table(net->ipv4.mrt);
 }
 #endif
 
@@ -336,6 +339,13 @@
 	return mrt;
 }
 
+static void ipmr_free_table(struct mr_table *mrt)
+{
+	del_timer_sync(&mrt->ipmr_expire_timer);
+	mroute_clean_tables(mrt);
+	kfree(mrt);
+}
+
 /* Service routines creating virtual interfaces: DVMRP tunnels and PIMREG */
 
 static void ipmr_del_tunnel(struct net_device *dev, struct vifctl *v)
diff --git a/net/ipv4/netfilter/nf_nat_sip.c b/net/ipv4/netfilter/nf_nat_sip.c
index 4ad9cf1..9c87cde 100644
--- a/net/ipv4/netfilter/nf_nat_sip.c
+++ b/net/ipv4/netfilter/nf_nat_sip.c
@@ -502,7 +502,10 @@
 		ret = nf_ct_expect_related(rtcp_exp);
 		if (ret == 0)
 			break;
-		else if (ret != -EBUSY) {
+		else if (ret == -EBUSY) {
+			nf_ct_unexpect_related(rtp_exp);
+			continue;
+		} else if (ret < 0) {
 			nf_ct_unexpect_related(rtp_exp);
 			port = 0;
 			break;
diff --git a/net/ipv4/route.c b/net/ipv4/route.c
index fd9ecb5..82cf2a7 100644
--- a/net/ipv4/route.c
+++ b/net/ipv4/route.c
@@ -934,12 +934,14 @@
 	if (mtu < ip_rt_min_pmtu)
 		mtu = ip_rt_min_pmtu;
 
+	rcu_read_lock();
 	if (fib_lookup(dev_net(rt->dst.dev), fl4, &res) == 0) {
 		struct fib_nh *nh = &FIB_RES_NH(res);
 
 		update_or_create_fnhe(nh, fl4->daddr, 0, mtu,
 				      jiffies + ip_rt_mtu_expires);
 	}
+	rcu_read_unlock();
 	return mtu;
 }
 
@@ -956,7 +958,7 @@
 		dst->obsolete = DST_OBSOLETE_KILL;
 	} else {
 		rt->rt_pmtu = mtu;
-		dst_set_expires(&rt->dst, ip_rt_mtu_expires);
+		rt->dst.expires = max(1UL, jiffies + ip_rt_mtu_expires);
 	}
 }
 
@@ -1263,7 +1265,7 @@
 {
 	struct rtable *rt = (struct rtable *) dst;
 
-	if (dst->flags & DST_NOCACHE) {
+	if (!list_empty(&rt->rt_uncached)) {
 		spin_lock_bh(&rt_uncached_lock);
 		list_del(&rt->rt_uncached);
 		spin_unlock_bh(&rt_uncached_lock);
diff --git a/net/ipv4/tcp_input.c b/net/ipv4/tcp_input.c
index 85308b9..6e38c6c 100644
--- a/net/ipv4/tcp_input.c
+++ b/net/ipv4/tcp_input.c
@@ -2926,13 +2926,14 @@
  * tcp_xmit_retransmit_queue().
  */
 static void tcp_fastretrans_alert(struct sock *sk, int pkts_acked,
-				  int newly_acked_sacked, bool is_dupack,
+				  int prior_sacked, bool is_dupack,
 				  int flag)
 {
 	struct inet_connection_sock *icsk = inet_csk(sk);
 	struct tcp_sock *tp = tcp_sk(sk);
 	int do_lost = is_dupack || ((flag & FLAG_DATA_SACKED) &&
 				    (tcp_fackets_out(tp) > tp->reordering));
+	int newly_acked_sacked = 0;
 	int fast_rexmit = 0;
 
 	if (WARN_ON(!tp->packets_out && tp->sacked_out))
@@ -2992,6 +2993,7 @@
 				tcp_add_reno_sack(sk);
 		} else
 			do_lost = tcp_try_undo_partial(sk, pkts_acked);
+		newly_acked_sacked = pkts_acked + tp->sacked_out - prior_sacked;
 		break;
 	case TCP_CA_Loss:
 		if (flag & FLAG_DATA_ACKED)
@@ -3013,6 +3015,7 @@
 			if (is_dupack)
 				tcp_add_reno_sack(sk);
 		}
+		newly_acked_sacked = pkts_acked + tp->sacked_out - prior_sacked;
 
 		if (icsk->icsk_ca_state <= TCP_CA_Disorder)
 			tcp_try_undo_dsack(sk);
@@ -3590,7 +3593,6 @@
 	int prior_packets;
 	int prior_sacked = tp->sacked_out;
 	int pkts_acked = 0;
-	int newly_acked_sacked = 0;
 	bool frto_cwnd = false;
 
 	/* If the ack is older than previous acks
@@ -3666,8 +3668,6 @@
 	flag |= tcp_clean_rtx_queue(sk, prior_fackets, prior_snd_una);
 
 	pkts_acked = prior_packets - tp->packets_out;
-	newly_acked_sacked = (prior_packets - prior_sacked) -
-			     (tp->packets_out - tp->sacked_out);
 
 	if (tp->frto_counter)
 		frto_cwnd = tcp_process_frto(sk, flag);
@@ -3681,7 +3681,7 @@
 		    tcp_may_raise_cwnd(sk, flag))
 			tcp_cong_avoid(sk, ack, prior_in_flight);
 		is_dupack = !(flag & (FLAG_SND_UNA_ADVANCED | FLAG_NOT_DUP));
-		tcp_fastretrans_alert(sk, pkts_acked, newly_acked_sacked,
+		tcp_fastretrans_alert(sk, pkts_acked, prior_sacked,
 				      is_dupack, flag);
 	} else {
 		if ((flag & FLAG_DATA_ACKED) && !frto_cwnd)
@@ -3698,7 +3698,7 @@
 no_queue:
 	/* If data was DSACKed, see if we can undo a cwnd reduction. */
 	if (flag & FLAG_DSACKING_ACK)
-		tcp_fastretrans_alert(sk, pkts_acked, newly_acked_sacked,
+		tcp_fastretrans_alert(sk, pkts_acked, prior_sacked,
 				      is_dupack, flag);
 	/* If this ack opens up a zero window, clear backoff.  It was
 	 * being used to time the probes, and is probably far higher than
@@ -3718,8 +3718,7 @@
 	 */
 	if (TCP_SKB_CB(skb)->sacked) {
 		flag |= tcp_sacktag_write_queue(sk, skb, prior_snd_una);
-		newly_acked_sacked = tp->sacked_out - prior_sacked;
-		tcp_fastretrans_alert(sk, pkts_acked, newly_acked_sacked,
+		tcp_fastretrans_alert(sk, pkts_acked, prior_sacked,
 				      is_dupack, flag);
 	}
 
diff --git a/net/ipv6/esp6.c b/net/ipv6/esp6.c
index 6dc7fd3..282f372 100644
--- a/net/ipv6/esp6.c
+++ b/net/ipv6/esp6.c
@@ -167,8 +167,6 @@
 	struct esp_data *esp = x->data;
 
 	/* skb is pure payload to encrypt */
-	err = -ENOMEM;
-
 	aead = esp->aead;
 	alen = crypto_aead_authsize(aead);
 
@@ -203,8 +201,10 @@
 	}
 
 	tmp = esp_alloc_tmp(aead, nfrags + sglists, seqhilen);
-	if (!tmp)
+	if (!tmp) {
+		err = -ENOMEM;
 		goto error;
+	}
 
 	seqhi = esp_tmp_seqhi(tmp);
 	iv = esp_tmp_iv(aead, tmp, seqhilen);
diff --git a/net/irda/ircomm/ircomm_param.c b/net/irda/ircomm/ircomm_param.c
index 8b915f3..3089391 100644
--- a/net/irda/ircomm/ircomm_param.c
+++ b/net/irda/ircomm/ircomm_param.c
@@ -99,7 +99,6 @@
  */
 int ircomm_param_request(struct ircomm_tty_cb *self, __u8 pi, int flush)
 {
-	struct tty_struct *tty;
 	unsigned long flags;
 	struct sk_buff *skb;
 	int count;
@@ -109,10 +108,6 @@
 	IRDA_ASSERT(self != NULL, return -1;);
 	IRDA_ASSERT(self->magic == IRCOMM_TTY_MAGIC, return -1;);
 
-	tty = self->tty;
-	if (!tty)
-		return 0;
-
 	/* Make sure we don't send parameters for raw mode */
 	if (self->service_type == IRCOMM_3_WIRE_RAW)
 		return 0;
diff --git a/net/irda/ircomm/ircomm_tty.c b/net/irda/ircomm/ircomm_tty.c
index 6b9d5a0..95a3a7a 100644
--- a/net/irda/ircomm/ircomm_tty.c
+++ b/net/irda/ircomm/ircomm_tty.c
@@ -52,6 +52,8 @@
 #include <net/irda/ircomm_tty_attach.h>
 #include <net/irda/ircomm_tty.h>
 
+static int ircomm_tty_install(struct tty_driver *driver,
+		struct tty_struct *tty);
 static int  ircomm_tty_open(struct tty_struct *tty, struct file *filp);
 static void ircomm_tty_close(struct tty_struct * tty, struct file *filp);
 static int  ircomm_tty_write(struct tty_struct * tty,
@@ -82,6 +84,7 @@
 static hashbin_t *ircomm_tty = NULL;
 
 static const struct tty_operations ops = {
+	.install	 = ircomm_tty_install,
 	.open            = ircomm_tty_open,
 	.close           = ircomm_tty_close,
 	.write           = ircomm_tty_write,
@@ -104,6 +107,35 @@
 #endif /* CONFIG_PROC_FS */
 };
 
+static void ircomm_port_raise_dtr_rts(struct tty_port *port, int raise)
+{
+	struct ircomm_tty_cb *self = container_of(port, struct ircomm_tty_cb,
+			port);
+	/*
+	 * Here, we use to lock those two guys, but as ircomm_param_request()
+	 * does it itself, I don't see the point (and I see the deadlock).
+	 * Jean II
+	 */
+	if (raise)
+		self->settings.dte |= IRCOMM_RTS | IRCOMM_DTR;
+	else
+		self->settings.dte &= ~(IRCOMM_RTS | IRCOMM_DTR);
+
+	ircomm_param_request(self, IRCOMM_DTE, TRUE);
+}
+
+static int ircomm_port_carrier_raised(struct tty_port *port)
+{
+	struct ircomm_tty_cb *self = container_of(port, struct ircomm_tty_cb,
+			port);
+	return self->settings.dce & IRCOMM_CD;
+}
+
+static const struct tty_port_operations ircomm_port_ops = {
+	.dtr_rts = ircomm_port_raise_dtr_rts,
+	.carrier_raised = ircomm_port_carrier_raised,
+};
+
 /*
  * Function ircomm_tty_init()
  *
@@ -194,7 +226,7 @@
 	IRDA_ASSERT(self->magic == IRCOMM_TTY_MAGIC, return -1;);
 
 	/* Check if already open */
-	if (test_and_set_bit(ASYNC_B_INITIALIZED, &self->flags)) {
+	if (test_and_set_bit(ASYNCB_INITIALIZED, &self->port.flags)) {
 		IRDA_DEBUG(2, "%s(), already open so break out!\n", __func__ );
 		return 0;
 	}
@@ -231,7 +263,7 @@
 
 	return 0;
 err:
-	clear_bit(ASYNC_B_INITIALIZED, &self->flags);
+	clear_bit(ASYNCB_INITIALIZED, &self->port.flags);
 	return ret;
 }
 
@@ -242,72 +274,62 @@
  *
  */
 static int ircomm_tty_block_til_ready(struct ircomm_tty_cb *self,
-				      struct file *filp)
+		struct tty_struct *tty, struct file *filp)
 {
+	struct tty_port *port = &self->port;
 	DECLARE_WAITQUEUE(wait, current);
 	int		retval;
 	int		do_clocal = 0, extra_count = 0;
 	unsigned long	flags;
-	struct tty_struct *tty;
 
 	IRDA_DEBUG(2, "%s()\n", __func__ );
 
-	tty = self->tty;
-
 	/*
 	 * If non-blocking mode is set, or the port is not enabled,
 	 * then make the check up front and then exit.
 	 */
 	if (filp->f_flags & O_NONBLOCK || tty->flags & (1 << TTY_IO_ERROR)){
 		/* nonblock mode is set or port is not enabled */
-		self->flags |= ASYNC_NORMAL_ACTIVE;
+		port->flags |= ASYNC_NORMAL_ACTIVE;
 		IRDA_DEBUG(1, "%s(), O_NONBLOCK requested!\n", __func__ );
 		return 0;
 	}
 
-	if (tty->termios->c_cflag & CLOCAL) {
+	if (tty->termios.c_cflag & CLOCAL) {
 		IRDA_DEBUG(1, "%s(), doing CLOCAL!\n", __func__ );
 		do_clocal = 1;
 	}
 
 	/* Wait for carrier detect and the line to become
 	 * free (i.e., not in use by the callout).  While we are in
-	 * this loop, self->open_count is dropped by one, so that
+	 * this loop, port->count is dropped by one, so that
 	 * mgsl_close() knows when to free things.  We restore it upon
 	 * exit, either normal or abnormal.
 	 */
 
 	retval = 0;
-	add_wait_queue(&self->open_wait, &wait);
+	add_wait_queue(&port->open_wait, &wait);
 
 	IRDA_DEBUG(2, "%s(%d):block_til_ready before block on %s open_count=%d\n",
-	      __FILE__,__LINE__, tty->driver->name, self->open_count );
+	      __FILE__, __LINE__, tty->driver->name, port->count);
 
-	/* As far as I can see, we protect open_count - Jean II */
-	spin_lock_irqsave(&self->spinlock, flags);
+	spin_lock_irqsave(&port->lock, flags);
 	if (!tty_hung_up_p(filp)) {
 		extra_count = 1;
-		self->open_count--;
+		port->count--;
 	}
-	spin_unlock_irqrestore(&self->spinlock, flags);
-	self->blocked_open++;
+	spin_unlock_irqrestore(&port->lock, flags);
+	port->blocked_open++;
 
 	while (1) {
-		if (tty->termios->c_cflag & CBAUD) {
-			/* Here, we use to lock those two guys, but
-			 * as ircomm_param_request() does it itself,
-			 * I don't see the point (and I see the deadlock).
-			 * Jean II */
-			self->settings.dte |= IRCOMM_RTS + IRCOMM_DTR;
-
-			ircomm_param_request(self, IRCOMM_DTE, TRUE);
-		}
+		if (tty->termios.c_cflag & CBAUD)
+			tty_port_raise_dtr_rts(port);
 
 		current->state = TASK_INTERRUPTIBLE;
 
 		if (tty_hung_up_p(filp) ||
-		    !test_bit(ASYNC_B_INITIALIZED, &self->flags)) {
-			retval = (self->flags & ASYNC_HUP_NOTIFY) ?
+		    !test_bit(ASYNCB_INITIALIZED, &port->flags)) {
+			retval = (port->flags & ASYNC_HUP_NOTIFY) ?
 					-EAGAIN : -ERESTARTSYS;
 			break;
 		}
@@ -317,8 +339,8 @@
 		 * specified, we cannot return before the IrCOMM link is
 		 * ready
 		 */
-		if (!test_bit(ASYNC_B_CLOSING, &self->flags) &&
-		    (do_clocal || (self->settings.dce & IRCOMM_CD)) &&
+		if (!test_bit(ASYNCB_CLOSING, &port->flags) &&
+		    (do_clocal || tty_port_carrier_raised(port)) &&
 		    self->state == IRCOMM_TTY_READY)
 		{
 			break;
@@ -330,46 +352,36 @@
 		}
 
 		IRDA_DEBUG(1, "%s(%d):block_til_ready blocking on %s open_count=%d\n",
-		      __FILE__,__LINE__, tty->driver->name, self->open_count );
+		      __FILE__, __LINE__, tty->driver->name, port->count);
 
 		schedule();
 	}
 
 	__set_current_state(TASK_RUNNING);
-	remove_wait_queue(&self->open_wait, &wait);
+	remove_wait_queue(&port->open_wait, &wait);
 
 	if (extra_count) {
 		/* ++ is not atomic, so this should be protected - Jean II */
-		spin_lock_irqsave(&self->spinlock, flags);
-		self->open_count++;
-		spin_unlock_irqrestore(&self->spinlock, flags);
+		spin_lock_irqsave(&port->lock, flags);
+		port->count++;
+		spin_unlock_irqrestore(&port->lock, flags);
 	}
-	self->blocked_open--;
+	port->blocked_open--;
 
 	IRDA_DEBUG(1, "%s(%d):block_til_ready after blocking on %s open_count=%d\n",
-	      __FILE__,__LINE__, tty->driver->name, self->open_count);
+	      __FILE__, __LINE__, tty->driver->name, port->count);
 
 	if (!retval)
-		self->flags |= ASYNC_NORMAL_ACTIVE;
+		port->flags |= ASYNC_NORMAL_ACTIVE;
 
 	return retval;
 }
 
-/*
- * Function ircomm_tty_open (tty, filp)
- *
- *    This routine is called when a particular tty device is opened. This
- *    routine is mandatory; if this routine is not filled in, the attempted
- *    open will fail with ENODEV.
- */
-static int ircomm_tty_open(struct tty_struct *tty, struct file *filp)
+
+static int ircomm_tty_install(struct tty_driver *driver, struct tty_struct *tty)
 {
 	struct ircomm_tty_cb *self;
 	unsigned int line = tty->index;
-	unsigned long	flags;
-	int ret;
-
-	IRDA_DEBUG(2, "%s()\n", __func__ );
 
 	/* Check if instance already exists */
 	self = hashbin_lock_find(ircomm_tty, line, NULL);
@@ -381,6 +393,8 @@
 			return -ENOMEM;
 		}
 
+		tty_port_init(&self->port);
+		self->port.ops = &ircomm_port_ops;
 		self->magic = IRCOMM_TTY_MAGIC;
 		self->flow = FLOW_STOP;
 
@@ -388,13 +402,9 @@
 		INIT_WORK(&self->tqueue, ircomm_tty_do_softint);
 		self->max_header_size = IRCOMM_TTY_HDR_UNINITIALISED;
 		self->max_data_size = IRCOMM_TTY_DATA_UNINITIALISED;
-		self->close_delay = 5*HZ/10;
-		self->closing_wait = 30*HZ;
 
 		/* Init some important stuff */
 		init_timer(&self->watchdog_timer);
-		init_waitqueue_head(&self->open_wait);
-		init_waitqueue_head(&self->close_wait);
 		spin_lock_init(&self->spinlock);
 
 		/*
@@ -404,31 +414,48 @@
 		 *
 		 * Note this is completely usafe and doesn't work properly
 		 */
-		tty->termios->c_iflag = 0;
-		tty->termios->c_oflag = 0;
+		tty->termios.c_iflag = 0;
+		tty->termios.c_oflag = 0;
 
 		/* Insert into hash */
 		hashbin_insert(ircomm_tty, (irda_queue_t *) self, line, NULL);
 	}
-	/* ++ is not atomic, so this should be protected - Jean II */
-	spin_lock_irqsave(&self->spinlock, flags);
-	self->open_count++;
 
-	tty->driver_data = self;
-	self->tty = tty;
-	spin_unlock_irqrestore(&self->spinlock, flags);
+	return tty_port_install(&self->port, driver, tty);
+}
+
+/*
+ * Function ircomm_tty_open (tty, filp)
+ *
+ *    This routine is called when a particular tty device is opened. This
+ *    routine is mandatory; if this routine is not filled in, the attempted
+ *    open will fail with ENODEV.
+ */
+static int ircomm_tty_open(struct tty_struct *tty, struct file *filp)
+{
+	struct ircomm_tty_cb *self = tty->driver_data;
+	unsigned long	flags;
+	int ret;
+
+	IRDA_DEBUG(2, "%s()\n", __func__ );
+
+	/* ++ is not atomic, so this should be protected - Jean II */
+	spin_lock_irqsave(&self->port.lock, flags);
+	self->port.count++;
+	spin_unlock_irqrestore(&self->port.lock, flags);
+	tty_port_tty_set(&self->port, tty);
 
 	IRDA_DEBUG(1, "%s(), %s%d, count = %d\n", __func__ , tty->driver->name,
-		   self->line, self->open_count);
+		   self->line, self->port.count);
 
 	/* Not really used by us, but lets do it anyway */
-	self->tty->low_latency = (self->flags & ASYNC_LOW_LATENCY) ? 1 : 0;
+	tty->low_latency = (self->port.flags & ASYNC_LOW_LATENCY) ? 1 : 0;
 
 	/*
 	 * If the port is the middle of closing, bail out now
 	 */
 	if (tty_hung_up_p(filp) ||
-	    test_bit(ASYNC_B_CLOSING, &self->flags)) {
+	    test_bit(ASYNCB_CLOSING, &self->port.flags)) {
 
 		/* Hm, why are we blocking on ASYNC_CLOSING if we
 		 * do return -EAGAIN/-ERESTARTSYS below anyway?
@@ -438,14 +465,15 @@
 		 * probably better sleep uninterruptible?
 		 */
 
-		if (wait_event_interruptible(self->close_wait, !test_bit(ASYNC_B_CLOSING, &self->flags))) {
+		if (wait_event_interruptible(self->port.close_wait,
+				!test_bit(ASYNCB_CLOSING, &self->port.flags))) {
 			IRDA_WARNING("%s - got signal while blocking on ASYNC_CLOSING!\n",
 				     __func__);
 			return -ERESTARTSYS;
 		}
 
 #ifdef SERIAL_DO_RESTART
-		return (self->flags & ASYNC_HUP_NOTIFY) ?
+		return (self->port.flags & ASYNC_HUP_NOTIFY) ?
 			-EAGAIN : -ERESTARTSYS;
 #else
 		return -EAGAIN;
@@ -453,7 +481,7 @@
 	}
 
 	/* Check if this is a "normal" ircomm device, or an irlpt device */
-	if (line < 0x10) {
+	if (self->line < 0x10) {
 		self->service_type = IRCOMM_3_WIRE | IRCOMM_9_WIRE;
 		self->settings.service_type = IRCOMM_9_WIRE; /* 9 wire as default */
 		/* Jan Kiszka -> add DSR/RI -> Conform to IrCOMM spec */
@@ -469,7 +497,7 @@
 	if (ret)
 		return ret;
 
-	ret = ircomm_tty_block_til_ready(self, filp);
+	ret = ircomm_tty_block_til_ready(self, tty, filp);
 	if (ret) {
 		IRDA_DEBUG(2,
 		      "%s(), returning after block_til_ready with %d\n", __func__ ,
@@ -489,81 +517,22 @@
 static void ircomm_tty_close(struct tty_struct *tty, struct file *filp)
 {
 	struct ircomm_tty_cb *self = (struct ircomm_tty_cb *) tty->driver_data;
-	unsigned long flags;
+	struct tty_port *port = &self->port;
 
 	IRDA_DEBUG(0, "%s()\n", __func__ );
 
 	IRDA_ASSERT(self != NULL, return;);
 	IRDA_ASSERT(self->magic == IRCOMM_TTY_MAGIC, return;);
 
-	spin_lock_irqsave(&self->spinlock, flags);
-
-	if (tty_hung_up_p(filp)) {
-		spin_unlock_irqrestore(&self->spinlock, flags);
-
-		IRDA_DEBUG(0, "%s(), returning 1\n", __func__ );
+	if (tty_port_close_start(port, tty, filp) == 0)
 		return;
-	}
-
-	if ((tty->count == 1) && (self->open_count != 1)) {
-		/*
-		 * Uh, oh.  tty->count is 1, which means that the tty
-		 * structure will be freed.  state->count should always
-		 * be one in these conditions.  If it's greater than
-		 * one, we've got real problems, since it means the
-		 * serial port won't be shutdown.
-		 */
-		IRDA_DEBUG(0, "%s(), bad serial port count; "
-			   "tty->count is 1, state->count is %d\n", __func__ ,
-			   self->open_count);
-		self->open_count = 1;
-	}
-
-	if (--self->open_count < 0) {
-		IRDA_ERROR("%s(), bad serial port count for ttys%d: %d\n",
-			   __func__, self->line, self->open_count);
-		self->open_count = 0;
-	}
-	if (self->open_count) {
-		spin_unlock_irqrestore(&self->spinlock, flags);
-
-		IRDA_DEBUG(0, "%s(), open count > 0\n", __func__ );
-		return;
-	}
-
-	/* Hum... Should be test_and_set_bit ??? - Jean II */
-	set_bit(ASYNC_B_CLOSING, &self->flags);
-
-	/* We need to unlock here (we were unlocking at the end of this
-	 * function), because tty_wait_until_sent() may schedule.
-	 * I don't know if the rest should be protected somehow,
-	 * so someone should check. - Jean II */
-	spin_unlock_irqrestore(&self->spinlock, flags);
-
-	/*
-	 * Now we wait for the transmit buffer to clear; and we notify
-	 * the line discipline to only process XON/XOFF characters.
-	 */
-	tty->closing = 1;
-	if (self->closing_wait != ASYNC_CLOSING_WAIT_NONE)
-		tty_wait_until_sent_from_close(tty, self->closing_wait);
 
 	ircomm_tty_shutdown(self);
 
 	tty_driver_flush_buffer(tty);
-	tty_ldisc_flush(tty);
 
-	tty->closing = 0;
-	self->tty = NULL;
-
-	if (self->blocked_open) {
-		if (self->close_delay)
-			schedule_timeout_interruptible(self->close_delay);
-		wake_up_interruptible(&self->open_wait);
-	}
-
-	self->flags &= ~(ASYNC_NORMAL_ACTIVE|ASYNC_CLOSING);
-	wake_up_interruptible(&self->close_wait);
+	tty_port_close_end(port, tty);
+	tty_port_tty_set(port, NULL);
 }
 
 /*
@@ -606,7 +575,7 @@
 	if (!self || self->magic != IRCOMM_TTY_MAGIC)
 		return;
 
-	tty = self->tty;
+	tty = tty_port_tty_get(&self->port);
 	if (!tty)
 		return;
 
@@ -627,7 +596,7 @@
 	}
 
 	if (tty->hw_stopped)
-		return;
+		goto put;
 
 	/* Unlink transmit buffer */
 	spin_lock_irqsave(&self->spinlock, flags);
@@ -646,6 +615,8 @@
 
 	/* Check if user (still) wants to be waken up */
 	tty_wakeup(tty);
+put:
+	tty_kref_put(tty);
 }
 
 /*
@@ -880,7 +851,7 @@
 		ircomm_tty_send_xchar(tty, STOP_CHAR(tty));
 
 	/* Hardware flow control? */
-	if (tty->termios->c_cflag & CRTSCTS) {
+	if (tty->termios.c_cflag & CRTSCTS) {
 		self->settings.dte &= ~IRCOMM_RTS;
 		self->settings.dte |= IRCOMM_DELTA_RTS;
 
@@ -912,7 +883,7 @@
 	}
 
 	/* Using hardware flow control? */
-	if (tty->termios->c_cflag & CRTSCTS) {
+	if (tty->termios.c_cflag & CRTSCTS) {
 		self->settings.dte |= (IRCOMM_RTS|IRCOMM_DELTA_RTS);
 
 		ircomm_param_request(self, IRCOMM_DTE, TRUE);
@@ -955,7 +926,7 @@
 
 	IRDA_DEBUG(0, "%s()\n", __func__ );
 
-	if (!test_and_clear_bit(ASYNC_B_INITIALIZED, &self->flags))
+	if (!test_and_clear_bit(ASYNCB_INITIALIZED, &self->port.flags))
 		return;
 
 	ircomm_tty_detach_cable(self);
@@ -994,6 +965,7 @@
 static void ircomm_tty_hangup(struct tty_struct *tty)
 {
 	struct ircomm_tty_cb *self = (struct ircomm_tty_cb *) tty->driver_data;
+	struct tty_port *port = &self->port;
 	unsigned long	flags;
 
 	IRDA_DEBUG(0, "%s()\n", __func__ );
@@ -1004,14 +976,17 @@
 	/* ircomm_tty_flush_buffer(tty); */
 	ircomm_tty_shutdown(self);
 
-	/* I guess we need to lock here - Jean II */
-	spin_lock_irqsave(&self->spinlock, flags);
-	self->flags &= ~ASYNC_NORMAL_ACTIVE;
-	self->tty = NULL;
-	self->open_count = 0;
-	spin_unlock_irqrestore(&self->spinlock, flags);
+	spin_lock_irqsave(&port->lock, flags);
+	port->flags &= ~ASYNC_NORMAL_ACTIVE;
+	if (port->tty) {
+		set_bit(TTY_IO_ERROR, &port->tty->flags);
+		tty_kref_put(port->tty);
+	}
+	port->tty = NULL;
+	port->count = 0;
+	spin_unlock_irqrestore(&port->lock, flags);
 
-	wake_up_interruptible(&self->open_wait);
+	wake_up_interruptible(&port->open_wait);
 }
 
 /*
@@ -1071,20 +1046,20 @@
 	IRDA_ASSERT(self != NULL, return;);
 	IRDA_ASSERT(self->magic == IRCOMM_TTY_MAGIC, return;);
 
-	tty = self->tty;
+	tty = tty_port_tty_get(&self->port);
 
 	status = self->settings.dce;
 
 	if (status & IRCOMM_DCE_DELTA_ANY) {
 		/*wake_up_interruptible(&self->delta_msr_wait);*/
 	}
-	if ((self->flags & ASYNC_CHECK_CD) && (status & IRCOMM_DELTA_CD)) {
+	if ((self->port.flags & ASYNC_CHECK_CD) && (status & IRCOMM_DELTA_CD)) {
 		IRDA_DEBUG(2,
 			   "%s(), ircomm%d CD now %s...\n", __func__ , self->line,
 			   (status & IRCOMM_CD) ? "on" : "off");
 
 		if (status & IRCOMM_CD) {
-			wake_up_interruptible(&self->open_wait);
+			wake_up_interruptible(&self->port.open_wait);
 		} else {
 			IRDA_DEBUG(2,
 				   "%s(), Doing serial hangup..\n", __func__ );
@@ -1092,10 +1067,10 @@
 				tty_hangup(tty);
 
 			/* Hangup will remote the tty, so better break out */
-			return;
+			goto put;
 		}
 	}
-	if (self->flags & ASYNC_CTS_FLOW) {
+	if (tty && tty_port_cts_enabled(&self->port)) {
 		if (tty->hw_stopped) {
 			if (status & IRCOMM_CTS) {
 				IRDA_DEBUG(2,
@@ -1103,10 +1078,10 @@
 				tty->hw_stopped = 0;
 
 				/* Wake up processes blocked on open */
-				wake_up_interruptible(&self->open_wait);
+				wake_up_interruptible(&self->port.open_wait);
 
 				schedule_work(&self->tqueue);
-				return;
+				goto put;
 			}
 		} else {
 			if (!(status & IRCOMM_CTS)) {
@@ -1116,6 +1091,8 @@
 			}
 		}
 	}
+put:
+	tty_kref_put(tty);
 }
 
 /*
@@ -1128,6 +1105,7 @@
 				      struct sk_buff *skb)
 {
 	struct ircomm_tty_cb *self = (struct ircomm_tty_cb *) instance;
+	struct tty_struct *tty;
 
 	IRDA_DEBUG(2, "%s()\n", __func__ );
 
@@ -1135,7 +1113,8 @@
 	IRDA_ASSERT(self->magic == IRCOMM_TTY_MAGIC, return -1;);
 	IRDA_ASSERT(skb != NULL, return -1;);
 
-	if (!self->tty) {
+	tty = tty_port_tty_get(&self->port);
+	if (!tty) {
 		IRDA_DEBUG(0, "%s(), no tty!\n", __func__ );
 		return 0;
 	}
@@ -1146,7 +1125,7 @@
 	 * Devices like WinCE can do this, and since they don't send any
 	 * params, we can just as well declare the hardware for running.
 	 */
-	if (self->tty->hw_stopped && (self->flow == FLOW_START)) {
+	if (tty->hw_stopped && (self->flow == FLOW_START)) {
 		IRDA_DEBUG(0, "%s(), polling for line settings!\n", __func__ );
 		ircomm_param_request(self, IRCOMM_POLL, TRUE);
 
@@ -1159,8 +1138,9 @@
 	 * Use flip buffer functions since the code may be called from interrupt
 	 * context
 	 */
-	tty_insert_flip_string(self->tty, skb->data, skb->len);
-	tty_flip_buffer_push(self->tty);
+	tty_insert_flip_string(tty, skb->data, skb->len);
+	tty_flip_buffer_push(tty);
+	tty_kref_put(tty);
 
 	/* No need to kfree_skb - see ircomm_ttp_data_indication() */
 
@@ -1211,12 +1191,13 @@
 	IRDA_ASSERT(self != NULL, return;);
 	IRDA_ASSERT(self->magic == IRCOMM_TTY_MAGIC, return;);
 
-	tty = self->tty;
+	tty = tty_port_tty_get(&self->port);
 
 	switch (cmd) {
 	case FLOW_START:
 		IRDA_DEBUG(2, "%s(), hw start!\n", __func__ );
-		tty->hw_stopped = 0;
+		if (tty)
+			tty->hw_stopped = 0;
 
 		/* ircomm_tty_do_softint will take care of the rest */
 		schedule_work(&self->tqueue);
@@ -1224,15 +1205,19 @@
 	default:  /* If we get here, something is very wrong, better stop */
 	case FLOW_STOP:
 		IRDA_DEBUG(2, "%s(), hw stopped!\n", __func__ );
-		tty->hw_stopped = 1;
+		if (tty)
+			tty->hw_stopped = 1;
 		break;
 	}
+
+	tty_kref_put(tty);
 	self->flow = cmd;
 }
 
 #ifdef CONFIG_PROC_FS
 static void ircomm_tty_line_info(struct ircomm_tty_cb *self, struct seq_file *m)
 {
+	struct tty_struct *tty;
 	char sep;
 
 	seq_printf(m, "State: %s\n", ircomm_tty_state[self->state]);
@@ -1328,40 +1313,43 @@
 
 	seq_puts(m, "Flags:");
 	sep = ' ';
-	if (self->flags & ASYNC_CTS_FLOW) {
+	if (tty_port_cts_enabled(&self->port)) {
 		seq_printf(m, "%cASYNC_CTS_FLOW", sep);
 		sep = '|';
 	}
-	if (self->flags & ASYNC_CHECK_CD) {
+	if (self->port.flags & ASYNC_CHECK_CD) {
 		seq_printf(m, "%cASYNC_CHECK_CD", sep);
 		sep = '|';
 	}
-	if (self->flags & ASYNC_INITIALIZED) {
+	if (self->port.flags & ASYNC_INITIALIZED) {
 		seq_printf(m, "%cASYNC_INITIALIZED", sep);
 		sep = '|';
 	}
-	if (self->flags & ASYNC_LOW_LATENCY) {
+	if (self->port.flags & ASYNC_LOW_LATENCY) {
 		seq_printf(m, "%cASYNC_LOW_LATENCY", sep);
 		sep = '|';
 	}
-	if (self->flags & ASYNC_CLOSING) {
+	if (self->port.flags & ASYNC_CLOSING) {
 		seq_printf(m, "%cASYNC_CLOSING", sep);
 		sep = '|';
 	}
-	if (self->flags & ASYNC_NORMAL_ACTIVE) {
+	if (self->port.flags & ASYNC_NORMAL_ACTIVE) {
 		seq_printf(m, "%cASYNC_NORMAL_ACTIVE", sep);
 		sep = '|';
 	}
 	seq_putc(m, '\n');
 
 	seq_printf(m, "Role: %s\n", self->client ? "client" : "server");
-	seq_printf(m, "Open count: %d\n", self->open_count);
+	seq_printf(m, "Open count: %d\n", self->port.count);
 	seq_printf(m, "Max data size: %d\n", self->max_data_size);
 	seq_printf(m, "Max header size: %d\n", self->max_header_size);
 
-	if (self->tty)
+	tty = tty_port_tty_get(&self->port);
+	if (tty) {
 		seq_printf(m, "Hardware: %s\n",
-			       self->tty->hw_stopped ? "Stopped" : "Running");
+			       tty->hw_stopped ? "Stopped" : "Running");
+		tty_kref_put(tty);
+	}
 }
 
 static int ircomm_tty_proc_show(struct seq_file *m, void *v)
diff --git a/net/irda/ircomm/ircomm_tty_attach.c b/net/irda/ircomm/ircomm_tty_attach.c
index b65d66e..edab393 100644
--- a/net/irda/ircomm/ircomm_tty_attach.c
+++ b/net/irda/ircomm/ircomm_tty_attach.c
@@ -130,6 +130,8 @@
  */
 int ircomm_tty_attach_cable(struct ircomm_tty_cb *self)
 {
+	struct tty_struct *tty;
+
 	IRDA_DEBUG(0, "%s()\n", __func__ );
 
 	IRDA_ASSERT(self != NULL, return -1;);
@@ -142,7 +144,11 @@
 	}
 
 	/* Make sure nobody tries to write before the link is up */
-	self->tty->hw_stopped = 1;
+	tty = tty_port_tty_get(&self->port);
+	if (tty) {
+		tty->hw_stopped = 1;
+		tty_kref_put(tty);
+	}
 
 	ircomm_tty_ias_register(self);
 
@@ -398,23 +404,26 @@
 				      struct sk_buff *skb)
 {
 	struct ircomm_tty_cb *self = (struct ircomm_tty_cb *) instance;
+	struct tty_struct *tty;
 
 	IRDA_DEBUG(2, "%s()\n", __func__ );
 
 	IRDA_ASSERT(self != NULL, return;);
 	IRDA_ASSERT(self->magic == IRCOMM_TTY_MAGIC, return;);
 
-	if (!self->tty)
+	tty = tty_port_tty_get(&self->port);
+	if (!tty)
 		return;
 
 	/* This will stop control data transfers */
 	self->flow = FLOW_STOP;
 
 	/* Stop data transfers */
-	self->tty->hw_stopped = 1;
+	tty->hw_stopped = 1;
 
 	ircomm_tty_do_event(self, IRCOMM_TTY_DISCONNECT_INDICATION, NULL,
 			    NULL);
+	tty_kref_put(tty);
 }
 
 /*
@@ -550,12 +559,15 @@
  */
 void ircomm_tty_link_established(struct ircomm_tty_cb *self)
 {
+	struct tty_struct *tty;
+
 	IRDA_DEBUG(2, "%s()\n", __func__ );
 
 	IRDA_ASSERT(self != NULL, return;);
 	IRDA_ASSERT(self->magic == IRCOMM_TTY_MAGIC, return;);
 
-	if (!self->tty)
+	tty = tty_port_tty_get(&self->port);
+	if (!tty)
 		return;
 
 	del_timer(&self->watchdog_timer);
@@ -566,19 +578,22 @@
 	 * will have to wait for the peer device (DCE) to raise the CTS
 	 * line.
 	 */
-	if ((self->flags & ASYNC_CTS_FLOW) && ((self->settings.dce & IRCOMM_CTS) == 0)) {
+	if (tty_port_cts_enabled(&self->port) &&
+			((self->settings.dce & IRCOMM_CTS) == 0)) {
 		IRDA_DEBUG(0, "%s(), waiting for CTS ...\n", __func__ );
-		return;
+		goto put;
 	} else {
 		IRDA_DEBUG(1, "%s(), starting hardware!\n", __func__ );
 
-		self->tty->hw_stopped = 0;
+		tty->hw_stopped = 0;
 
 		/* Wake up processes blocked on open */
-		wake_up_interruptible(&self->open_wait);
+		wake_up_interruptible(&self->port.open_wait);
 	}
 
 	schedule_work(&self->tqueue);
+put:
+	tty_kref_put(tty);
 }
 
 /*
@@ -977,14 +992,17 @@
 		ircomm_tty_next_state(self, IRCOMM_TTY_SEARCH);
 		ircomm_tty_start_watchdog_timer(self, 3*HZ);
 
-		if (self->flags & ASYNC_CHECK_CD) {
+		if (self->port.flags & ASYNC_CHECK_CD) {
 			/* Drop carrier */
 			self->settings.dce = IRCOMM_DELTA_CD;
 			ircomm_tty_check_modem_status(self);
 		} else {
+			struct tty_struct *tty = tty_port_tty_get(&self->port);
 			IRDA_DEBUG(0, "%s(), hanging up!\n", __func__ );
-			if (self->tty)
-				tty_hangup(self->tty);
+			if (tty) {
+				tty_hangup(tty);
+				tty_kref_put(tty);
+			}
 		}
 		break;
 	default:
diff --git a/net/irda/ircomm/ircomm_tty_ioctl.c b/net/irda/ircomm/ircomm_tty_ioctl.c
index d0667d6..b343f50 100644
--- a/net/irda/ircomm/ircomm_tty_ioctl.c
+++ b/net/irda/ircomm/ircomm_tty_ioctl.c
@@ -52,17 +52,18 @@
  *    Change speed of the driver. If the remote device is a DCE, then this
  *    should make it change the speed of its serial port
  */
-static void ircomm_tty_change_speed(struct ircomm_tty_cb *self)
+static void ircomm_tty_change_speed(struct ircomm_tty_cb *self,
+		struct tty_struct *tty)
 {
 	unsigned int cflag, cval;
 	int baud;
 
 	IRDA_DEBUG(2, "%s()\n", __func__ );
 
-	if (!self->tty || !self->tty->termios || !self->ircomm)
+	if (!self->ircomm)
 		return;
 
-	cflag = self->tty->termios->c_cflag;
+	cflag = tty->termios.c_cflag;
 
 	/*  byte size and parity */
 	switch (cflag & CSIZE) {
@@ -81,7 +82,7 @@
 		cval |= IRCOMM_PARITY_EVEN;
 
 	/* Determine divisor based on baud rate */
-	baud = tty_get_baud_rate(self->tty);
+	baud = tty_get_baud_rate(tty);
 	if (!baud)
 		baud = 9600;	/* B0 transition handled in rs_set_termios */
 
@@ -90,19 +91,19 @@
 
 	/* CTS flow control flag and modem status interrupts */
 	if (cflag & CRTSCTS) {
-		self->flags |= ASYNC_CTS_FLOW;
+		self->port.flags |= ASYNC_CTS_FLOW;
 		self->settings.flow_control |= IRCOMM_RTS_CTS_IN;
 		/* This got me. Bummer. Jean II */
 		if (self->service_type == IRCOMM_3_WIRE_RAW)
 			IRDA_WARNING("%s(), enabling RTS/CTS on link that doesn't support it (3-wire-raw)\n", __func__);
 	} else {
-		self->flags &= ~ASYNC_CTS_FLOW;
+		self->port.flags &= ~ASYNC_CTS_FLOW;
 		self->settings.flow_control &= ~IRCOMM_RTS_CTS_IN;
 	}
 	if (cflag & CLOCAL)
-		self->flags &= ~ASYNC_CHECK_CD;
+		self->port.flags &= ~ASYNC_CHECK_CD;
 	else
-		self->flags |= ASYNC_CHECK_CD;
+		self->port.flags |= ASYNC_CHECK_CD;
 #if 0
 	/*
 	 * Set up parity check flag
@@ -148,18 +149,18 @@
 			    struct ktermios *old_termios)
 {
 	struct ircomm_tty_cb *self = (struct ircomm_tty_cb *) tty->driver_data;
-	unsigned int cflag = tty->termios->c_cflag;
+	unsigned int cflag = tty->termios.c_cflag;
 
 	IRDA_DEBUG(2, "%s()\n", __func__ );
 
 	if ((cflag == old_termios->c_cflag) &&
-	    (RELEVANT_IFLAG(tty->termios->c_iflag) ==
+	    (RELEVANT_IFLAG(tty->termios.c_iflag) ==
 	     RELEVANT_IFLAG(old_termios->c_iflag)))
 	{
 		return;
 	}
 
-	ircomm_tty_change_speed(self);
+	ircomm_tty_change_speed(self, tty);
 
 	/* Handle transition to B0 status */
 	if ((old_termios->c_cflag & CBAUD) &&
@@ -172,7 +173,7 @@
 	if (!(old_termios->c_cflag & CBAUD) &&
 	    (cflag & CBAUD)) {
 		self->settings.dte |= IRCOMM_DTR;
-		if (!(tty->termios->c_cflag & CRTSCTS) ||
+		if (!(tty->termios.c_cflag & CRTSCTS) ||
 		    !test_bit(TTY_THROTTLED, &tty->flags)) {
 			self->settings.dte |= IRCOMM_RTS;
 		}
@@ -181,7 +182,7 @@
 
 	/* Handle turning off CRTSCTS */
 	if ((old_termios->c_cflag & CRTSCTS) &&
-	    !(tty->termios->c_cflag & CRTSCTS))
+	    !(tty->termios.c_cflag & CRTSCTS))
 	{
 		tty->hw_stopped = 0;
 		ircomm_tty_start(tty);
@@ -270,10 +271,10 @@
 
 	memset(&info, 0, sizeof(info));
 	info.line = self->line;
-	info.flags = self->flags;
+	info.flags = self->port.flags;
 	info.baud_base = self->settings.data_rate;
-	info.close_delay = self->close_delay;
-	info.closing_wait = self->closing_wait;
+	info.close_delay = self->port.close_delay;
+	info.closing_wait = self->port.closing_wait;
 
 	/* For compatibility  */
 	info.type = PORT_16550A;
diff --git a/net/l2tp/l2tp_core.c b/net/l2tp/l2tp_core.c
index 393355d..513cab0 100644
--- a/net/l2tp/l2tp_core.c
+++ b/net/l2tp/l2tp_core.c
@@ -1347,11 +1347,10 @@
 	/* Remove from tunnel list */
 	spin_lock_bh(&pn->l2tp_tunnel_list_lock);
 	list_del_rcu(&tunnel->list);
+	kfree_rcu(tunnel, rcu);
 	spin_unlock_bh(&pn->l2tp_tunnel_list_lock);
-	synchronize_rcu();
 
 	atomic_dec(&l2tp_tunnel_count);
-	kfree(tunnel);
 }
 
 /* Create a socket for the tunnel, if one isn't set up by
diff --git a/net/l2tp/l2tp_core.h b/net/l2tp/l2tp_core.h
index a38ec6c..56d583e 100644
--- a/net/l2tp/l2tp_core.h
+++ b/net/l2tp/l2tp_core.h
@@ -163,6 +163,7 @@
 
 struct l2tp_tunnel {
 	int			magic;		/* Should be L2TP_TUNNEL_MAGIC */
+	struct rcu_head rcu;
 	rwlock_t		hlist_lock;	/* protect session_hlist */
 	struct hlist_head	session_hlist[L2TP_HASH_SIZE];
 						/* hashed list of sessions,
diff --git a/net/mac80211/tx.c b/net/mac80211/tx.c
index acf712f..c5e8c9c 100644
--- a/net/mac80211/tx.c
+++ b/net/mac80211/tx.c
@@ -1811,37 +1811,31 @@
 			meshhdrlen = ieee80211_new_mesh_header(&mesh_hdr,
 					sdata, NULL, NULL);
 		} else {
-			int is_mesh_mcast = 1;
-			const u8 *mesh_da;
+			/* DS -> MBSS (802.11-2012 13.11.3.3).
+			 * For unicast with unknown forwarding information,
+			 * destination might be in the MBSS or if that fails
+			 * forwarded to another mesh gate. In either case
+			 * resolution will be handled in ieee80211_xmit(), so
+			 * leave the original DA. This also works for mcast */
+			const u8 *mesh_da = skb->data;
 
-			if (is_multicast_ether_addr(skb->data))
-				/* DA TA mSA AE:SA */
-				mesh_da = skb->data;
-			else {
-				static const u8 bcast[ETH_ALEN] =
-					{ 0xff, 0xff, 0xff, 0xff, 0xff, 0xff };
-				if (mppath) {
-					/* RA TA mDA mSA AE:DA SA */
-					mesh_da = mppath->mpp;
-					is_mesh_mcast = 0;
-				} else if (mpath) {
-					mesh_da = mpath->dst;
-					is_mesh_mcast = 0;
-				} else {
-					/* DA TA mSA AE:SA */
-					mesh_da = bcast;
-				}
-			}
+			if (mppath)
+				mesh_da = mppath->mpp;
+			else if (mpath)
+				mesh_da = mpath->dst;
+			rcu_read_unlock();
+
 			hdrlen = ieee80211_fill_mesh_addresses(&hdr, &fc,
 					mesh_da, sdata->vif.addr);
-			rcu_read_unlock();
-			if (is_mesh_mcast)
+			if (is_multicast_ether_addr(mesh_da))
+				/* DA TA mSA AE:SA */
 				meshhdrlen =
 					ieee80211_new_mesh_header(&mesh_hdr,
 							sdata,
 							skb->data + ETH_ALEN,
 							NULL);
 			else
+				/* RA TA mDA mSA AE:DA SA */
 				meshhdrlen =
 					ieee80211_new_mesh_header(&mesh_hdr,
 							sdata,
diff --git a/net/netfilter/ipvs/ip_vs_ctl.c b/net/netfilter/ipvs/ip_vs_ctl.c
index 72bf32a..f51013c 100644
--- a/net/netfilter/ipvs/ip_vs_ctl.c
+++ b/net/netfilter/ipvs/ip_vs_ctl.c
@@ -1171,8 +1171,10 @@
 		goto out_err;
 	}
 	svc->stats.cpustats = alloc_percpu(struct ip_vs_cpu_stats);
-	if (!svc->stats.cpustats)
+	if (!svc->stats.cpustats) {
+		ret = -ENOMEM;
 		goto out_err;
+	}
 
 	/* I'm the first user of the service */
 	atomic_set(&svc->usecnt, 0);
diff --git a/net/netfilter/nf_conntrack_core.c b/net/netfilter/nf_conntrack_core.c
index cf48755..2ceec64 100644
--- a/net/netfilter/nf_conntrack_core.c
+++ b/net/netfilter/nf_conntrack_core.c
@@ -249,12 +249,15 @@
 {
 	struct nf_conn *ct = (void *)ul_conntrack;
 	struct net *net = nf_ct_net(ct);
+	struct nf_conntrack_ecache *ecache = nf_ct_ecache_find(ct);
+
+	BUG_ON(ecache == NULL);
 
 	if (nf_conntrack_event(IPCT_DESTROY, ct) < 0) {
 		/* bad luck, let's retry again */
-		ct->timeout.expires = jiffies +
+		ecache->timeout.expires = jiffies +
 			(random32() % net->ct.sysctl_events_retry_timeout);
-		add_timer(&ct->timeout);
+		add_timer(&ecache->timeout);
 		return;
 	}
 	/* we've got the event delivered, now it's dying */
@@ -268,6 +271,9 @@
 void nf_ct_insert_dying_list(struct nf_conn *ct)
 {
 	struct net *net = nf_ct_net(ct);
+	struct nf_conntrack_ecache *ecache = nf_ct_ecache_find(ct);
+
+	BUG_ON(ecache == NULL);
 
 	/* add this conntrack to the dying list */
 	spin_lock_bh(&nf_conntrack_lock);
@@ -275,10 +281,10 @@
 			     &net->ct.dying);
 	spin_unlock_bh(&nf_conntrack_lock);
 	/* set a new timer to retry event delivery */
-	setup_timer(&ct->timeout, death_by_event, (unsigned long)ct);
-	ct->timeout.expires = jiffies +
+	setup_timer(&ecache->timeout, death_by_event, (unsigned long)ct);
+	ecache->timeout.expires = jiffies +
 		(random32() % net->ct.sysctl_events_retry_timeout);
-	add_timer(&ct->timeout);
+	add_timer(&ecache->timeout);
 }
 EXPORT_SYMBOL_GPL(nf_ct_insert_dying_list);
 
diff --git a/net/netfilter/nf_conntrack_netlink.c b/net/netfilter/nf_conntrack_netlink.c
index da4fc37..9807f32 100644
--- a/net/netfilter/nf_conntrack_netlink.c
+++ b/net/netfilter/nf_conntrack_netlink.c
@@ -2790,7 +2790,8 @@
 		goto err_unreg_subsys;
 	}
 
-	if (register_pernet_subsys(&ctnetlink_net_ops)) {
+	ret = register_pernet_subsys(&ctnetlink_net_ops);
+	if (ret < 0) {
 		pr_err("ctnetlink_init: cannot register pernet operations\n");
 		goto err_unreg_exp_subsys;
 	}
diff --git a/net/netfilter/nfnetlink_log.c b/net/netfilter/nfnetlink_log.c
index 169ab59..14e2f39 100644
--- a/net/netfilter/nfnetlink_log.c
+++ b/net/netfilter/nfnetlink_log.c
@@ -480,7 +480,7 @@
 	}
 
 	if (indev && skb_mac_header_was_set(skb)) {
-		if (nla_put_be32(inst->skb, NFULA_HWTYPE, htons(skb->dev->type)) ||
+		if (nla_put_be16(inst->skb, NFULA_HWTYPE, htons(skb->dev->type)) ||
 		    nla_put_be16(inst->skb, NFULA_HWLEN,
 				 htons(skb->dev->hard_header_len)) ||
 		    nla_put(inst->skb, NFULA_HWHEADER, skb->dev->hard_header_len,
@@ -996,8 +996,10 @@
 
 #ifdef CONFIG_PROC_FS
 	if (!proc_create("nfnetlink_log", 0440,
-			 proc_net_netfilter, &nful_file_ops))
+			 proc_net_netfilter, &nful_file_ops)) {
+		status = -ENOMEM;
 		goto cleanup_logger;
+	}
 #endif
 	return status;
 
diff --git a/net/netlink/af_netlink.c b/net/netlink/af_netlink.c
index 1445d73..5270238 100644
--- a/net/netlink/af_netlink.c
+++ b/net/netlink/af_netlink.c
@@ -1373,7 +1373,8 @@
 		dst_pid = addr->nl_pid;
 		dst_group = ffs(addr->nl_groups);
 		err =  -EPERM;
-		if (dst_group && !netlink_capable(sock, NL_NONROOT_SEND))
+		if ((dst_group || dst_pid) &&
+		    !netlink_capable(sock, NL_NONROOT_SEND))
 			goto out;
 	} else {
 		dst_pid = nlk->dst_pid;
@@ -2147,6 +2148,7 @@
 	rcu_assign_pointer(nl_table[NETLINK_USERSOCK].listeners, listeners);
 	nl_table[NETLINK_USERSOCK].module = THIS_MODULE;
 	nl_table[NETLINK_USERSOCK].registered = 1;
+	nl_table[NETLINK_USERSOCK].nl_nonroot = NL_NONROOT_SEND;
 
 	netlink_table_ungrab();
 }
diff --git a/net/packet/af_packet.c b/net/packet/af_packet.c
index aee7196..c5c9e2a 100644
--- a/net/packet/af_packet.c
+++ b/net/packet/af_packet.c
@@ -1273,7 +1273,7 @@
 	spin_unlock(&f->lock);
 }
 
-bool match_fanout_group(struct packet_type *ptype, struct sock * sk)
+static bool match_fanout_group(struct packet_type *ptype, struct sock * sk)
 {
 	if (ptype->af_packet_priv == (void*)((struct packet_sock *)sk)->fanout)
 		return true;
diff --git a/net/socket.c b/net/socket.c
index a5471f8..edc3c4a 100644
--- a/net/socket.c
+++ b/net/socket.c
@@ -2604,7 +2604,7 @@
 	err = sock_do_ioctl(net, sock, cmd, (unsigned long)&ktv);
 	set_fs(old_fs);
 	if (!err)
-		err = compat_put_timeval(up, &ktv);
+		err = compat_put_timeval(&ktv, up);
 
 	return err;
 }
@@ -2620,7 +2620,7 @@
 	err = sock_do_ioctl(net, sock, cmd, (unsigned long)&kts);
 	set_fs(old_fs);
 	if (!err)
-		err = compat_put_timespec(up, &kts);
+		err = compat_put_timespec(&kts, up);
 
 	return err;
 }
diff --git a/net/sunrpc/svc_xprt.c b/net/sunrpc/svc_xprt.c
index 88f2bf6..bac973a 100644
--- a/net/sunrpc/svc_xprt.c
+++ b/net/sunrpc/svc_xprt.c
@@ -316,7 +316,6 @@
  */
 void svc_xprt_enqueue(struct svc_xprt *xprt)
 {
-	struct svc_serv	*serv = xprt->xpt_server;
 	struct svc_pool *pool;
 	struct svc_rqst	*rqstp;
 	int cpu;
@@ -362,8 +361,6 @@
 				rqstp, rqstp->rq_xprt);
 		rqstp->rq_xprt = xprt;
 		svc_xprt_get(xprt);
-		rqstp->rq_reserved = serv->sv_max_mesg;
-		atomic_add(rqstp->rq_reserved, &xprt->xpt_reserved);
 		pool->sp_stats.threads_woken++;
 		wake_up(&rqstp->rq_wait);
 	} else {
@@ -640,8 +637,6 @@
 	if (xprt) {
 		rqstp->rq_xprt = xprt;
 		svc_xprt_get(xprt);
-		rqstp->rq_reserved = serv->sv_max_mesg;
-		atomic_add(rqstp->rq_reserved, &xprt->xpt_reserved);
 
 		/* As there is a shortage of threads and this request
 		 * had to be queued, don't allow the thread to wait so
@@ -738,6 +733,8 @@
 		else
 			len = xprt->xpt_ops->xpo_recvfrom(rqstp);
 		dprintk("svc: got len=%d\n", len);
+		rqstp->rq_reserved = serv->sv_max_mesg;
+		atomic_add(rqstp->rq_reserved, &xprt->xpt_reserved);
 	}
 	svc_xprt_received(xprt);
 
@@ -794,7 +791,8 @@
 
 	/* Grab mutex to serialize outgoing data. */
 	mutex_lock(&xprt->xpt_mutex);
-	if (test_bit(XPT_DEAD, &xprt->xpt_flags))
+	if (test_bit(XPT_DEAD, &xprt->xpt_flags)
+			|| test_bit(XPT_CLOSE, &xprt->xpt_flags))
 		len = -ENOTCONN;
 	else
 		len = xprt->xpt_ops->xpo_sendto(rqstp);
diff --git a/net/sunrpc/svcsock.c b/net/sunrpc/svcsock.c
index 18bc130..998aa8c 100644
--- a/net/sunrpc/svcsock.c
+++ b/net/sunrpc/svcsock.c
@@ -1129,9 +1129,9 @@
 	if (len >= 0)
 		svsk->sk_tcplen += len;
 	if (len != want) {
+		svc_tcp_save_pages(svsk, rqstp);
 		if (len < 0 && len != -EAGAIN)
 			goto err_other;
-		svc_tcp_save_pages(svsk, rqstp);
 		dprintk("svc: incomplete TCP record (%d of %d)\n",
 			svsk->sk_tcplen, svsk->sk_reclen);
 		goto err_noclose;
diff --git a/net/xfrm/xfrm_state.c b/net/xfrm/xfrm_state.c
index 87cd0e4..210be48 100644
--- a/net/xfrm/xfrm_state.c
+++ b/net/xfrm/xfrm_state.c
@@ -1994,8 +1994,10 @@
 		goto error;
 
 	x->outer_mode = xfrm_get_mode(x->props.mode, family);
-	if (x->outer_mode == NULL)
+	if (x->outer_mode == NULL) {
+		err = -EPROTONOSUPPORT;
 		goto error;
+	}
 
 	if (init_replay) {
 		err = xfrm_init_replay(x);
diff --git a/scripts/Makefile.fwinst b/scripts/Makefile.fwinst
index 6bf8e87..c3f69ae2 100644
--- a/scripts/Makefile.fwinst
+++ b/scripts/Makefile.fwinst
@@ -42,7 +42,7 @@
 $(installed-fw-dirs):
 	$(call cmd,mkdir)
 
-$(installed-fw): $(INSTALL_FW_PATH)/%: $(obj)/% | $(INSTALL_FW_PATH)/$$(dir %)
+$(installed-fw): $(INSTALL_FW_PATH)/%: $(obj)/% | $$(dir $(INSTALL_FW_PATH)/%)
 	$(call cmd,install)
 
 PHONY +=  __fw_install __fw_modinst FORCE
diff --git a/scripts/link-vmlinux.sh b/scripts/link-vmlinux.sh
index 4629038c..4235a63 100644
--- a/scripts/link-vmlinux.sh
+++ b/scripts/link-vmlinux.sh
@@ -211,7 +211,7 @@
 
 	if ! cmp -s System.map .tmp_System.map; then
 		echo >&2 Inconsistent kallsyms data
-		echo >&2 echo Try "make KALLSYMS_EXTRA_PASS=1" as a workaround
+		echo >&2 Try "make KALLSYMS_EXTRA_PASS=1" as a workaround
 		cleanup
 		exit 1
 	fi
diff --git a/sound/pci/hda/hda_codec.c b/sound/pci/hda/hda_codec.c
index f560051..f25c24c 100644
--- a/sound/pci/hda/hda_codec.c
+++ b/sound/pci/hda/hda_codec.c
@@ -1209,6 +1209,9 @@
 	kfree(codec);
 }
 
+static bool snd_hda_codec_get_supported_ps(struct hda_codec *codec,
+				hda_nid_t fg, unsigned int power_state);
+
 static void hda_set_power_state(struct hda_codec *codec, hda_nid_t fg,
 				unsigned int power_state);
 
@@ -1317,6 +1320,10 @@
 					   AC_VERB_GET_SUBSYSTEM_ID, 0);
 	}
 
+	codec->epss = snd_hda_codec_get_supported_ps(codec,
+					codec->afg ? codec->afg : codec->mfg,
+					AC_PWRST_EPSS);
+
 	/* power-up all before initialization */
 	hda_set_power_state(codec,
 			    codec->afg ? codec->afg : codec->mfg,
@@ -3543,8 +3550,7 @@
 	/* this delay seems necessary to avoid click noise at power-down */
 	if (power_state == AC_PWRST_D3) {
 		/* transition time less than 10ms for power down */
-		bool epss = snd_hda_codec_get_supported_ps(codec, fg, AC_PWRST_EPSS);
-		msleep(epss ? 10 : 100);
+		msleep(codec->epss ? 10 : 100);
 	}
 
 	/* repeat power states setting at most 10 times*/
diff --git a/sound/pci/hda/hda_codec.h b/sound/pci/hda/hda_codec.h
index 7fbc1bc..e5a7e19 100644
--- a/sound/pci/hda/hda_codec.h
+++ b/sound/pci/hda/hda_codec.h
@@ -862,6 +862,7 @@
 	unsigned int ignore_misc_bit:1; /* ignore MISC_NO_PRESENCE bit */
 	unsigned int no_jack_detect:1;	/* Machine has no jack-detection */
 	unsigned int pcm_format_first:1; /* PCM format must be set first */
+	unsigned int epss:1;		/* supporting EPSS? */
 #ifdef CONFIG_SND_HDA_POWER_SAVE
 	unsigned int power_on :1;	/* current (global) power-state */
 	int power_transition;	/* power-state in transition */
diff --git a/sound/pci/hda/patch_sigmatel.c b/sound/pci/hda/patch_sigmatel.c
index ea5775a..6f806d3 100644
--- a/sound/pci/hda/patch_sigmatel.c
+++ b/sound/pci/hda/patch_sigmatel.c
@@ -4543,6 +4543,9 @@
 	struct auto_pin_cfg *cfg = &spec->autocfg;
 	int i;
 
+	if (cfg->speaker_outs == 0)
+		return;
+
 	for (i = 0; i < cfg->line_outs; i++) {
 		if (presence)
 			break;
@@ -5531,6 +5534,7 @@
 		snd_hda_codec_set_pincfg(codec, 0xf, 0x2181205e);
 	}
 
+	codec->epss = 0; /* longer delay needed for D3 */
 	codec->no_trigger_sense = 1;
 	codec->spec = spec;
 
diff --git a/sound/usb/card.c b/sound/usb/card.c
index d5b5c33..4a469f0 100644
--- a/sound/usb/card.c
+++ b/sound/usb/card.c
@@ -553,7 +553,7 @@
 				     struct snd_usb_audio *chip)
 {
 	struct snd_card *card;
-	struct list_head *p;
+	struct list_head *p, *n;
 
 	if (chip == (void *)-1L)
 		return;
@@ -570,7 +570,7 @@
 			snd_usb_stream_disconnect(p);
 		}
 		/* release the endpoint resources */
-		list_for_each(p, &chip->ep_list) {
+		list_for_each_safe(p, n, &chip->ep_list) {
 			snd_usb_endpoint_free(p);
 		}
 		/* release the midi resources */
diff --git a/sound/usb/endpoint.c b/sound/usb/endpoint.c
index c411812..d6e2bb4 100644
--- a/sound/usb/endpoint.c
+++ b/sound/usb/endpoint.c
@@ -141,7 +141,7 @@
  *
  * For implicit feedback, next_packet_size() is unused.
  */
-static int next_packet_size(struct snd_usb_endpoint *ep)
+int snd_usb_endpoint_next_packet_size(struct snd_usb_endpoint *ep)
 {
 	unsigned long flags;
 	int ret;
@@ -177,15 +177,6 @@
 		ep->retire_data_urb(ep->data_subs, urb);
 }
 
-static void prepare_outbound_urb_sizes(struct snd_usb_endpoint *ep,
-				       struct snd_urb_ctx *ctx)
-{
-	int i;
-
-	for (i = 0; i < ctx->packets; ++i)
-		ctx->packet_size[i] = next_packet_size(ep);
-}
-
 /*
  * Prepare a PLAYBACK urb for submission to the bus.
  */
@@ -370,7 +361,6 @@
 			goto exit_clear;
 		}
 
-		prepare_outbound_urb_sizes(ep, ctx);
 		prepare_outbound_urb(ep, ctx);
 	} else {
 		retire_inbound_urb(ep, ctx);
@@ -799,7 +789,9 @@
 /**
  * snd_usb_endpoint_start: start an snd_usb_endpoint
  *
- * @ep: the endpoint to start
+ * @ep:		the endpoint to start
+ * @can_sleep:	flag indicating whether the operation is executed in
+ * 		non-atomic context
  *
  * A call to this function will increment the use count of the endpoint.
  * In case it is not already running, the URBs for this endpoint will be
@@ -809,7 +801,7 @@
  *
  * Returns an error if the URB submission failed, 0 in all other cases.
  */
-int snd_usb_endpoint_start(struct snd_usb_endpoint *ep)
+int snd_usb_endpoint_start(struct snd_usb_endpoint *ep, int can_sleep)
 {
 	int err;
 	unsigned int i;
@@ -821,6 +813,11 @@
 	if (++ep->use_count != 1)
 		return 0;
 
+	/* just to be sure */
+	deactivate_urbs(ep, 0, can_sleep);
+	if (can_sleep)
+		wait_clear_urbs(ep);
+
 	ep->active_mask = 0;
 	ep->unlink_mask = 0;
 	ep->phase = 0;
@@ -850,7 +847,6 @@
 			goto __error;
 
 		if (usb_pipeout(ep->pipe)) {
-			prepare_outbound_urb_sizes(ep, urb->context);
 			prepare_outbound_urb(ep, urb->context);
 		} else {
 			prepare_inbound_urb(ep, urb->context);
diff --git a/sound/usb/endpoint.h b/sound/usb/endpoint.h
index ee2723f..cbbbdf2 100644
--- a/sound/usb/endpoint.h
+++ b/sound/usb/endpoint.h
@@ -13,7 +13,7 @@
 				struct audioformat *fmt,
 				struct snd_usb_endpoint *sync_ep);
 
-int  snd_usb_endpoint_start(struct snd_usb_endpoint *ep);
+int  snd_usb_endpoint_start(struct snd_usb_endpoint *ep, int can_sleep);
 void snd_usb_endpoint_stop(struct snd_usb_endpoint *ep,
 			   int force, int can_sleep, int wait);
 int  snd_usb_endpoint_activate(struct snd_usb_endpoint *ep);
@@ -21,6 +21,7 @@
 void snd_usb_endpoint_free(struct list_head *head);
 
 int snd_usb_endpoint_implict_feedback_sink(struct snd_usb_endpoint *ep);
+int snd_usb_endpoint_next_packet_size(struct snd_usb_endpoint *ep);
 
 void snd_usb_handle_sync_urb(struct snd_usb_endpoint *ep,
 			     struct snd_usb_endpoint *sender,
diff --git a/sound/usb/pcm.c b/sound/usb/pcm.c
index 62ec808..fd5e982 100644
--- a/sound/usb/pcm.c
+++ b/sound/usb/pcm.c
@@ -212,7 +212,7 @@
 	}
 }
 
-static int start_endpoints(struct snd_usb_substream *subs)
+static int start_endpoints(struct snd_usb_substream *subs, int can_sleep)
 {
 	int err;
 
@@ -225,7 +225,7 @@
 		snd_printdd(KERN_DEBUG "Starting data EP @%p\n", ep);
 
 		ep->data_subs = subs;
-		err = snd_usb_endpoint_start(ep);
+		err = snd_usb_endpoint_start(ep, can_sleep);
 		if (err < 0) {
 			clear_bit(SUBSTREAM_FLAG_DATA_EP_STARTED, &subs->flags);
 			return err;
@@ -236,10 +236,25 @@
 	    !test_and_set_bit(SUBSTREAM_FLAG_SYNC_EP_STARTED, &subs->flags)) {
 		struct snd_usb_endpoint *ep = subs->sync_endpoint;
 
+		if (subs->data_endpoint->iface != subs->sync_endpoint->iface ||
+		    subs->data_endpoint->alt_idx != subs->sync_endpoint->alt_idx) {
+			err = usb_set_interface(subs->dev,
+						subs->sync_endpoint->iface,
+						subs->sync_endpoint->alt_idx);
+			if (err < 0) {
+				snd_printk(KERN_ERR
+					   "%d:%d:%d: cannot set interface (%d)\n",
+					   subs->dev->devnum,
+					   subs->sync_endpoint->iface,
+					   subs->sync_endpoint->alt_idx, err);
+				return -EIO;
+			}
+		}
+
 		snd_printdd(KERN_DEBUG "Starting sync EP @%p\n", ep);
 
 		ep->sync_slave = subs->data_endpoint;
-		err = snd_usb_endpoint_start(ep);
+		err = snd_usb_endpoint_start(ep, can_sleep);
 		if (err < 0) {
 			clear_bit(SUBSTREAM_FLAG_SYNC_EP_STARTED, &subs->flags);
 			return err;
@@ -544,13 +559,10 @@
 	subs->last_frame_number = 0;
 	runtime->delay = 0;
 
-	/* clear the pending deactivation on the target EPs */
-	deactivate_endpoints(subs);
-
 	/* for playback, submit the URBs now; otherwise, the first hwptr_done
 	 * updates for all URBs would happen at the same time when starting */
 	if (subs->direction == SNDRV_PCM_STREAM_PLAYBACK)
-		return start_endpoints(subs);
+		return start_endpoints(subs, 1);
 
 	return 0;
 }
@@ -1032,6 +1044,7 @@
 				 struct urb *urb)
 {
 	struct snd_pcm_runtime *runtime = subs->pcm_substream->runtime;
+	struct snd_usb_endpoint *ep = subs->data_endpoint;
 	struct snd_urb_ctx *ctx = urb->context;
 	unsigned int counts, frames, bytes;
 	int i, stride, period_elapsed = 0;
@@ -1043,7 +1056,11 @@
 	urb->number_of_packets = 0;
 	spin_lock_irqsave(&subs->lock, flags);
 	for (i = 0; i < ctx->packets; i++) {
-		counts = ctx->packet_size[i];
+		if (ctx->packet_size[i])
+			counts = ctx->packet_size[i];
+		else
+			counts = snd_usb_endpoint_next_packet_size(ep);
+
 		/* set up descriptor */
 		urb->iso_frame_desc[i].offset = frames * stride;
 		urb->iso_frame_desc[i].length = counts * stride;
@@ -1094,7 +1111,16 @@
 	subs->hwptr_done += bytes;
 	if (subs->hwptr_done >= runtime->buffer_size * stride)
 		subs->hwptr_done -= runtime->buffer_size * stride;
+
+	/* update delay with exact number of samples queued */
+	runtime->delay = subs->last_delay;
 	runtime->delay += frames;
+	subs->last_delay = runtime->delay;
+
+	/* realign last_frame_number */
+	subs->last_frame_number = usb_get_current_frame_number(subs->dev);
+	subs->last_frame_number &= 0xFF; /* keep 8 LSBs */
+
 	spin_unlock_irqrestore(&subs->lock, flags);
 	urb->transfer_buffer_length = bytes;
 	if (period_elapsed)
@@ -1112,12 +1138,26 @@
 	struct snd_pcm_runtime *runtime = subs->pcm_substream->runtime;
 	int stride = runtime->frame_bits >> 3;
 	int processed = urb->transfer_buffer_length / stride;
+	int est_delay;
 
 	spin_lock_irqsave(&subs->lock, flags);
-	if (processed > runtime->delay)
-		runtime->delay = 0;
+	est_delay = snd_usb_pcm_delay(subs, runtime->rate);
+	/* update delay with exact number of samples played */
+	if (processed > subs->last_delay)
+		subs->last_delay = 0;
 	else
-		runtime->delay -= processed;
+		subs->last_delay -= processed;
+	runtime->delay = subs->last_delay;
+
+	/*
+	 * Report when delay estimate is off by more than 2ms.
+	 * The error should be lower than 2ms since the estimate relies
+	 * on two reads of a counter updated every ms.
+	 */
+	if (abs(est_delay - subs->last_delay) * 1000 > runtime->rate * 2)
+		snd_printk(KERN_DEBUG "delay: estimated %d, actual %d\n",
+			est_delay, subs->last_delay);
+
 	spin_unlock_irqrestore(&subs->lock, flags);
 }
 
@@ -1175,7 +1215,7 @@
 
 	switch (cmd) {
 	case SNDRV_PCM_TRIGGER_START:
-		err = start_endpoints(subs);
+		err = start_endpoints(subs, 0);
 		if (err < 0)
 			return err;
 
diff --git a/tools/perf/util/python-ext-sources b/tools/perf/util/python-ext-sources
index 2884e67..2133628 100644
--- a/tools/perf/util/python-ext-sources
+++ b/tools/perf/util/python-ext-sources
@@ -10,10 +10,12 @@
 util/evlist.c
 util/evsel.c
 util/cpumap.c
+util/hweight.c
 util/thread_map.c
 util/util.c
 util/xyarray.c
 util/cgroup.c
 util/debugfs.c
+util/rblist.c
 util/strlist.c
 ../../lib/rbtree.c
diff --git a/virt/kvm/kvm_main.c b/virt/kvm/kvm_main.c
index 2468523..d617f69 100644
--- a/virt/kvm/kvm_main.c
+++ b/virt/kvm/kvm_main.c
@@ -1976,9 +1976,10 @@
 			if (copy_from_user(&csigset, sigmask_arg->sigset,
 					   sizeof csigset))
 				goto out;
-		}
-		sigset_from_compat(&sigset, &csigset);
-		r = kvm_vcpu_ioctl_set_sigmask(vcpu, &sigset);
+			sigset_from_compat(&sigset, &csigset);
+			r = kvm_vcpu_ioctl_set_sigmask(vcpu, &sigset);
+		} else
+			r = kvm_vcpu_ioctl_set_sigmask(vcpu, NULL);
 		break;
 	}
 	default: