| /* |
| * Copyright (c) 2005-2011 Atheros Communications Inc. |
| * Copyright (c) 2011-2013 Qualcomm Atheros, Inc. |
| * |
| * Permission to use, copy, modify, and/or distribute this software for any |
| * purpose with or without fee is hereby granted, provided that the above |
| * copyright notice and this permission notice appear in all copies. |
| * |
| * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES |
| * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF |
| * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR |
| * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES |
| * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN |
| * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF |
| * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. |
| */ |
| |
| #ifndef _HW_H_ |
| #define _HW_H_ |
| |
| #include "targaddrs.h" |
| |
| #define ATH10K_FW_DIR "ath10k" |
| |
| #define QCA988X_2_0_DEVICE_ID (0x003c) |
| #define QCA6164_2_1_DEVICE_ID (0x0041) |
| #define QCA6174_2_1_DEVICE_ID (0x003e) |
| #define QCA99X0_2_0_DEVICE_ID (0x0040) |
| #define QCA9888_2_0_DEVICE_ID (0x0056) |
| #define QCA9984_1_0_DEVICE_ID (0x0046) |
| #define QCA9377_1_0_DEVICE_ID (0x0042) |
| #define QCA9887_1_0_DEVICE_ID (0x0050) |
| |
| /* QCA988X 1.0 definitions (unsupported) */ |
| #define QCA988X_HW_1_0_CHIP_ID_REV 0x0 |
| |
| /* QCA988X 2.0 definitions */ |
| #define QCA988X_HW_2_0_VERSION 0x4100016c |
| #define QCA988X_HW_2_0_CHIP_ID_REV 0x2 |
| #define QCA988X_HW_2_0_FW_DIR ATH10K_FW_DIR "/QCA988X/hw2.0" |
| #define QCA988X_HW_2_0_BOARD_DATA_FILE "board.bin" |
| #define QCA988X_HW_2_0_PATCH_LOAD_ADDR 0x1234 |
| |
| /* QCA9887 1.0 definitions */ |
| #define QCA9887_HW_1_0_VERSION 0x4100016d |
| #define QCA9887_HW_1_0_CHIP_ID_REV 0 |
| #define QCA9887_HW_1_0_FW_DIR ATH10K_FW_DIR "/QCA9887/hw1.0" |
| #define QCA9887_HW_1_0_BOARD_DATA_FILE "board.bin" |
| #define QCA9887_HW_1_0_PATCH_LOAD_ADDR 0x1234 |
| |
| /* QCA6174 target BMI version signatures */ |
| #define QCA6174_HW_1_0_VERSION 0x05000000 |
| #define QCA6174_HW_1_1_VERSION 0x05000001 |
| #define QCA6174_HW_1_3_VERSION 0x05000003 |
| #define QCA6174_HW_2_1_VERSION 0x05010000 |
| #define QCA6174_HW_3_0_VERSION 0x05020000 |
| #define QCA6174_HW_3_2_VERSION 0x05030000 |
| |
| /* QCA9377 target BMI version signatures */ |
| #define QCA9377_HW_1_0_DEV_VERSION 0x05020000 |
| #define QCA9377_HW_1_1_DEV_VERSION 0x05020001 |
| |
| enum qca6174_pci_rev { |
| QCA6174_PCI_REV_1_1 = 0x11, |
| QCA6174_PCI_REV_1_3 = 0x13, |
| QCA6174_PCI_REV_2_0 = 0x20, |
| QCA6174_PCI_REV_3_0 = 0x30, |
| }; |
| |
| enum qca6174_chip_id_rev { |
| QCA6174_HW_1_0_CHIP_ID_REV = 0, |
| QCA6174_HW_1_1_CHIP_ID_REV = 1, |
| QCA6174_HW_1_3_CHIP_ID_REV = 2, |
| QCA6174_HW_2_1_CHIP_ID_REV = 4, |
| QCA6174_HW_2_2_CHIP_ID_REV = 5, |
| QCA6174_HW_3_0_CHIP_ID_REV = 8, |
| QCA6174_HW_3_1_CHIP_ID_REV = 9, |
| QCA6174_HW_3_2_CHIP_ID_REV = 10, |
| }; |
| |
| enum qca9377_chip_id_rev { |
| QCA9377_HW_1_0_CHIP_ID_REV = 0x0, |
| QCA9377_HW_1_1_CHIP_ID_REV = 0x1, |
| }; |
| |
| #define QCA6174_HW_2_1_FW_DIR "ath10k/QCA6174/hw2.1" |
| #define QCA6174_HW_2_1_BOARD_DATA_FILE "board.bin" |
| #define QCA6174_HW_2_1_PATCH_LOAD_ADDR 0x1234 |
| |
| #define QCA6174_HW_3_0_FW_DIR "ath10k/QCA6174/hw3.0" |
| #define QCA6174_HW_3_0_BOARD_DATA_FILE "board.bin" |
| #define QCA6174_HW_3_0_PATCH_LOAD_ADDR 0x1234 |
| |
| /* QCA99X0 1.0 definitions (unsupported) */ |
| #define QCA99X0_HW_1_0_CHIP_ID_REV 0x0 |
| |
| /* QCA99X0 2.0 definitions */ |
| #define QCA99X0_HW_2_0_DEV_VERSION 0x01000000 |
| #define QCA99X0_HW_2_0_CHIP_ID_REV 0x1 |
| #define QCA99X0_HW_2_0_FW_DIR ATH10K_FW_DIR "/QCA99X0/hw2.0" |
| #define QCA99X0_HW_2_0_BOARD_DATA_FILE "board.bin" |
| #define QCA99X0_HW_2_0_PATCH_LOAD_ADDR 0x1234 |
| |
| /* QCA9984 1.0 defines */ |
| #define QCA9984_HW_1_0_DEV_VERSION 0x1000000 |
| #define QCA9984_HW_DEV_TYPE 0xa |
| #define QCA9984_HW_1_0_CHIP_ID_REV 0x0 |
| #define QCA9984_HW_1_0_FW_DIR ATH10K_FW_DIR "/QCA9984/hw1.0" |
| #define QCA9984_HW_1_0_BOARD_DATA_FILE "board.bin" |
| #define QCA9984_HW_1_0_PATCH_LOAD_ADDR 0x1234 |
| |
| /* QCA9888 2.0 defines */ |
| #define QCA9888_HW_2_0_DEV_VERSION 0x1000000 |
| #define QCA9888_HW_DEV_TYPE 0xc |
| #define QCA9888_HW_2_0_CHIP_ID_REV 0x0 |
| #define QCA9888_HW_2_0_FW_DIR ATH10K_FW_DIR "/QCA9888/hw2.0" |
| #define QCA9888_HW_2_0_BOARD_DATA_FILE "board.bin" |
| #define QCA9888_HW_2_0_PATCH_LOAD_ADDR 0x1234 |
| |
| /* QCA9377 1.0 definitions */ |
| #define QCA9377_HW_1_0_FW_DIR ATH10K_FW_DIR "/QCA9377/hw1.0" |
| #define QCA9377_HW_1_0_BOARD_DATA_FILE "board.bin" |
| #define QCA9377_HW_1_0_PATCH_LOAD_ADDR 0x1234 |
| |
| /* QCA4019 1.0 definitions */ |
| #define QCA4019_HW_1_0_DEV_VERSION 0x01000000 |
| #define QCA4019_HW_1_0_FW_DIR ATH10K_FW_DIR "/QCA4019/hw1.0" |
| #define QCA4019_HW_1_0_BOARD_DATA_FILE "board.bin" |
| #define QCA4019_HW_1_0_PATCH_LOAD_ADDR 0x1234 |
| |
| #define ATH10K_FW_FILE_BASE "firmware" |
| #define ATH10K_FW_API_MAX 6 |
| #define ATH10K_FW_API_MIN 2 |
| |
| #define ATH10K_FW_API2_FILE "firmware-2.bin" |
| #define ATH10K_FW_API3_FILE "firmware-3.bin" |
| |
| /* added support for ATH10K_FW_IE_WMI_OP_VERSION */ |
| #define ATH10K_FW_API4_FILE "firmware-4.bin" |
| |
| /* HTT id conflict fix for management frames over HTT */ |
| #define ATH10K_FW_API5_FILE "firmware-5.bin" |
| |
| /* the firmware-6.bin blob */ |
| #define ATH10K_FW_API6_FILE "firmware-6.bin" |
| |
| #define ATH10K_FW_UTF_FILE "utf.bin" |
| #define ATH10K_FW_UTF_API2_FILE "utf-2.bin" |
| |
| /* includes also the null byte */ |
| #define ATH10K_FIRMWARE_MAGIC "QCA-ATH10K" |
| #define ATH10K_BOARD_MAGIC "QCA-ATH10K-BOARD" |
| |
| #define ATH10K_BOARD_API2_FILE "board-2.bin" |
| |
| #define REG_DUMP_COUNT_QCA988X 60 |
| |
| struct ath10k_fw_ie { |
| __le32 id; |
| __le32 len; |
| u8 data[0]; |
| }; |
| |
| enum ath10k_fw_ie_type { |
| ATH10K_FW_IE_FW_VERSION = 0, |
| ATH10K_FW_IE_TIMESTAMP = 1, |
| ATH10K_FW_IE_FEATURES = 2, |
| ATH10K_FW_IE_FW_IMAGE = 3, |
| ATH10K_FW_IE_OTP_IMAGE = 4, |
| |
| /* WMI "operations" interface version, 32 bit value. Supported from |
| * FW API 4 and above. |
| */ |
| ATH10K_FW_IE_WMI_OP_VERSION = 5, |
| |
| /* HTT "operations" interface version, 32 bit value. Supported from |
| * FW API 5 and above. |
| */ |
| ATH10K_FW_IE_HTT_OP_VERSION = 6, |
| |
| /* Code swap image for firmware binary */ |
| ATH10K_FW_IE_FW_CODE_SWAP_IMAGE = 7, |
| }; |
| |
| enum ath10k_fw_wmi_op_version { |
| ATH10K_FW_WMI_OP_VERSION_UNSET = 0, |
| |
| ATH10K_FW_WMI_OP_VERSION_MAIN = 1, |
| ATH10K_FW_WMI_OP_VERSION_10_1 = 2, |
| ATH10K_FW_WMI_OP_VERSION_10_2 = 3, |
| ATH10K_FW_WMI_OP_VERSION_TLV = 4, |
| ATH10K_FW_WMI_OP_VERSION_10_2_4 = 5, |
| ATH10K_FW_WMI_OP_VERSION_10_4 = 6, |
| |
| /* keep last */ |
| ATH10K_FW_WMI_OP_VERSION_MAX, |
| }; |
| |
| enum ath10k_fw_htt_op_version { |
| ATH10K_FW_HTT_OP_VERSION_UNSET = 0, |
| |
| ATH10K_FW_HTT_OP_VERSION_MAIN = 1, |
| |
| /* also used in 10.2 and 10.2.4 branches */ |
| ATH10K_FW_HTT_OP_VERSION_10_1 = 2, |
| |
| ATH10K_FW_HTT_OP_VERSION_TLV = 3, |
| |
| ATH10K_FW_HTT_OP_VERSION_10_4 = 4, |
| |
| /* keep last */ |
| ATH10K_FW_HTT_OP_VERSION_MAX, |
| }; |
| |
| enum ath10k_bd_ie_type { |
| /* contains sub IEs of enum ath10k_bd_ie_board_type */ |
| ATH10K_BD_IE_BOARD = 0, |
| }; |
| |
| enum ath10k_bd_ie_board_type { |
| ATH10K_BD_IE_BOARD_NAME = 0, |
| ATH10K_BD_IE_BOARD_DATA = 1, |
| }; |
| |
| enum ath10k_hw_rev { |
| ATH10K_HW_QCA988X, |
| ATH10K_HW_QCA6174, |
| ATH10K_HW_QCA99X0, |
| ATH10K_HW_QCA9888, |
| ATH10K_HW_QCA9984, |
| ATH10K_HW_QCA9377, |
| ATH10K_HW_QCA4019, |
| ATH10K_HW_QCA9887, |
| ATH10K_HW_WCN3990, |
| }; |
| |
| struct ath10k_hw_regs { |
| u32 rtc_soc_base_address; |
| u32 rtc_wmac_base_address; |
| u32 soc_core_base_address; |
| u32 wlan_mac_base_address; |
| u32 ce_wrapper_base_address; |
| u32 ce0_base_address; |
| u32 ce1_base_address; |
| u32 ce2_base_address; |
| u32 ce3_base_address; |
| u32 ce4_base_address; |
| u32 ce5_base_address; |
| u32 ce6_base_address; |
| u32 ce7_base_address; |
| u32 ce8_base_address; |
| u32 ce9_base_address; |
| u32 ce10_base_address; |
| u32 ce11_base_address; |
| u32 soc_reset_control_si0_rst_mask; |
| u32 soc_reset_control_ce_rst_mask; |
| u32 soc_chip_id_address; |
| u32 scratch_3_address; |
| u32 fw_indicator_address; |
| u32 pcie_local_base_address; |
| u32 ce_wrap_intr_sum_host_msi_lsb; |
| u32 ce_wrap_intr_sum_host_msi_mask; |
| u32 pcie_intr_fw_mask; |
| u32 pcie_intr_ce_mask_all; |
| u32 pcie_intr_clr_address; |
| u32 cpu_pll_init_address; |
| u32 cpu_speed_address; |
| u32 core_clk_div_address; |
| }; |
| |
| extern const struct ath10k_hw_regs qca988x_regs; |
| extern const struct ath10k_hw_regs qca6174_regs; |
| extern const struct ath10k_hw_regs qca99x0_regs; |
| extern const struct ath10k_hw_regs qca4019_regs; |
| extern const struct ath10k_hw_regs wcn3990_regs; |
| |
| struct ath10k_hw_ce_regs_addr_map { |
| u32 msb; |
| u32 lsb; |
| u32 mask; |
| }; |
| |
| struct ath10k_hw_ce_ctrl1 { |
| u32 addr; |
| u32 hw_mask; |
| u32 sw_mask; |
| u32 hw_wr_mask; |
| u32 sw_wr_mask; |
| u32 reset_mask; |
| u32 reset; |
| struct ath10k_hw_ce_regs_addr_map *src_ring; |
| struct ath10k_hw_ce_regs_addr_map *dst_ring; |
| struct ath10k_hw_ce_regs_addr_map *dmax; }; |
| |
| struct ath10k_hw_ce_cmd_halt { |
| u32 status_reset; |
| u32 msb; |
| u32 mask; |
| struct ath10k_hw_ce_regs_addr_map *status; }; |
| |
| struct ath10k_hw_ce_host_ie { |
| u32 copy_complete_reset; |
| struct ath10k_hw_ce_regs_addr_map *copy_complete; }; |
| |
| struct ath10k_hw_ce_host_wm_regs { |
| u32 dstr_lmask; |
| u32 dstr_hmask; |
| u32 srcr_lmask; |
| u32 srcr_hmask; |
| u32 cc_mask; |
| u32 wm_mask; |
| u32 addr; |
| }; |
| |
| struct ath10k_hw_ce_misc_regs { |
| u32 axi_err; |
| u32 dstr_add_err; |
| u32 srcr_len_err; |
| u32 dstr_mlen_vio; |
| u32 dstr_overflow; |
| u32 srcr_overflow; |
| u32 err_mask; |
| u32 addr; |
| }; |
| |
| struct ath10k_hw_ce_dst_src_wm_regs { |
| u32 addr; |
| u32 low_rst; |
| u32 high_rst; |
| struct ath10k_hw_ce_regs_addr_map *wm_low; |
| struct ath10k_hw_ce_regs_addr_map *wm_high; }; |
| |
| struct ath10k_hw_ce_regs { |
| u32 sr_base_addr; |
| u32 sr_size_addr; |
| u32 dr_base_addr; |
| u32 dr_size_addr; |
| u32 ce_cmd_addr; |
| u32 misc_ie_addr; |
| u32 sr_wr_index_addr; |
| u32 dst_wr_index_addr; |
| u32 current_srri_addr; |
| u32 current_drri_addr; |
| u32 ddr_addr_for_rri_low; |
| u32 ddr_addr_for_rri_high; |
| u32 ce_rri_low; |
| u32 ce_rri_high; |
| u32 host_ie_addr; |
| struct ath10k_hw_ce_host_wm_regs *wm_regs; |
| struct ath10k_hw_ce_misc_regs *misc_regs; |
| struct ath10k_hw_ce_ctrl1 *ctrl1_regs; |
| struct ath10k_hw_ce_cmd_halt *cmd_halt; |
| struct ath10k_hw_ce_host_ie *host_ie; |
| struct ath10k_hw_ce_dst_src_wm_regs *wm_srcr; |
| struct ath10k_hw_ce_dst_src_wm_regs *wm_dstr; }; |
| |
| struct ath10k_hw_values { |
| u32 rtc_state_val_on; |
| u8 ce_count; |
| u8 msi_assign_ce_max; |
| u8 num_target_ce_config_wlan; |
| u16 ce_desc_meta_data_mask; |
| u8 ce_desc_meta_data_lsb; |
| }; |
| |
| extern const struct ath10k_hw_values qca988x_values; |
| extern const struct ath10k_hw_values qca6174_values; |
| extern const struct ath10k_hw_values qca99x0_values; |
| extern const struct ath10k_hw_values qca9888_values; |
| extern const struct ath10k_hw_values qca4019_values; |
| extern const struct ath10k_hw_values wcn3990_values; |
| extern struct ath10k_hw_ce_regs wcn3990_ce_regs; |
| extern struct ath10k_hw_ce_regs qcax_ce_regs; |
| |
| void ath10k_hw_fill_survey_time(struct ath10k *ar, struct survey_info *survey, |
| u32 cc, u32 rcc, u32 cc_prev, u32 rcc_prev); |
| |
| #define QCA_REV_988X(ar) ((ar)->hw_rev == ATH10K_HW_QCA988X) |
| #define QCA_REV_9887(ar) ((ar)->hw_rev == ATH10K_HW_QCA9887) |
| #define QCA_REV_6174(ar) ((ar)->hw_rev == ATH10K_HW_QCA6174) |
| #define QCA_REV_99X0(ar) ((ar)->hw_rev == ATH10K_HW_QCA99X0) |
| #define QCA_REV_9888(ar) ((ar)->hw_rev == ATH10K_HW_QCA9888) |
| #define QCA_REV_9984(ar) ((ar)->hw_rev == ATH10K_HW_QCA9984) |
| #define QCA_REV_9377(ar) ((ar)->hw_rev == ATH10K_HW_QCA9377) |
| #define QCA_REV_40XX(ar) ((ar)->hw_rev == ATH10K_HW_QCA4019) |
| #define QCA_REV_WCN3990(ar) ((ar)->hw_rev == ATH10K_HW_WCN3990) |
| |
| /* Known peculiarities: |
| * - raw appears in nwifi decap, raw and nwifi appear in ethernet decap |
| * - raw have FCS, nwifi doesn't |
| * - ethernet frames have 802.11 header decapped and parts (base hdr, cipher |
| * param, llc/snap) are aligned to 4byte boundaries each |
| */ |
| enum ath10k_hw_txrx_mode { |
| ATH10K_HW_TXRX_RAW = 0, |
| |
| /* Native Wifi decap mode is used to align IP frames to 4-byte |
| * boundaries and avoid a very expensive re-alignment in mac80211. |
| */ |
| ATH10K_HW_TXRX_NATIVE_WIFI = 1, |
| ATH10K_HW_TXRX_ETHERNET = 2, |
| |
| /* Valid for HTT >= 3.0. Used for management frames in TX_FRM. */ |
| ATH10K_HW_TXRX_MGMT = 3, |
| }; |
| |
| enum ath10k_mcast2ucast_mode { |
| ATH10K_MCAST2UCAST_DISABLED = 0, |
| ATH10K_MCAST2UCAST_ENABLED = 1, |
| }; |
| |
| enum ath10k_hw_rate_ofdm { |
| ATH10K_HW_RATE_OFDM_48M = 0, |
| ATH10K_HW_RATE_OFDM_24M, |
| ATH10K_HW_RATE_OFDM_12M, |
| ATH10K_HW_RATE_OFDM_6M, |
| ATH10K_HW_RATE_OFDM_54M, |
| ATH10K_HW_RATE_OFDM_36M, |
| ATH10K_HW_RATE_OFDM_18M, |
| ATH10K_HW_RATE_OFDM_9M, |
| }; |
| |
| enum ath10k_hw_rate_cck { |
| ATH10K_HW_RATE_CCK_LP_11M = 0, |
| ATH10K_HW_RATE_CCK_LP_5_5M, |
| ATH10K_HW_RATE_CCK_LP_2M, |
| ATH10K_HW_RATE_CCK_LP_1M, |
| ATH10K_HW_RATE_CCK_SP_11M, |
| ATH10K_HW_RATE_CCK_SP_5_5M, |
| ATH10K_HW_RATE_CCK_SP_2M, |
| }; |
| |
| enum ath10k_hw_rate_rev2_cck { |
| ATH10K_HW_RATE_REV2_CCK_LP_1M = 1, |
| ATH10K_HW_RATE_REV2_CCK_LP_2M, |
| ATH10K_HW_RATE_REV2_CCK_LP_5_5M, |
| ATH10K_HW_RATE_REV2_CCK_LP_11M, |
| ATH10K_HW_RATE_REV2_CCK_SP_2M, |
| ATH10K_HW_RATE_REV2_CCK_SP_5_5M, |
| ATH10K_HW_RATE_REV2_CCK_SP_11M, |
| }; |
| |
| enum ath10k_hw_cc_wraparound_type { |
| ATH10K_HW_CC_WRAP_DISABLED = 0, |
| |
| /* This type is when the HW chip has a quirky Cycle Counter |
| * wraparound which resets to 0x7fffffff instead of 0. All |
| * other CC related counters (e.g. Rx Clear Count) are divided |
| * by 2 so they never wraparound themselves. |
| */ |
| ATH10K_HW_CC_WRAP_SHIFTED_ALL = 1, |
| |
| /* Each hw counter wrapsaround independently. When the |
| * counter overflows the repestive counter is right shifted |
| * by 1, i.e reset to 0x7fffffff, and other counters will be |
| * running unaffected. In this type of wraparound, it should |
| * be possible to report accurate Rx busy time unlike the |
| * first type. |
| */ |
| ATH10K_HW_CC_WRAP_SHIFTED_EACH = 2, |
| }; |
| |
| enum ath10k_hw_refclk_speed { |
| ATH10K_HW_REFCLK_UNKNOWN = -1, |
| ATH10K_HW_REFCLK_48_MHZ = 0, |
| ATH10K_HW_REFCLK_19_2_MHZ = 1, |
| ATH10K_HW_REFCLK_24_MHZ = 2, |
| ATH10K_HW_REFCLK_26_MHZ = 3, |
| ATH10K_HW_REFCLK_37_4_MHZ = 4, |
| ATH10K_HW_REFCLK_38_4_MHZ = 5, |
| ATH10K_HW_REFCLK_40_MHZ = 6, |
| ATH10K_HW_REFCLK_52_MHZ = 7, |
| |
| /* must be the last one */ |
| ATH10K_HW_REFCLK_COUNT, |
| }; |
| |
| struct ath10k_hw_clk_params { |
| u32 refclk; |
| u32 div; |
| u32 rnfrac; |
| u32 settle_time; |
| u32 refdiv; |
| u32 outdiv; |
| }; |
| |
| struct ath10k_hw_params { |
| u32 id; |
| u16 dev_id; |
| const char *name; |
| u32 patch_load_addr; |
| int uart_pin; |
| u32 otp_exe_param; |
| |
| /* Type of hw cycle counter wraparound logic, for more info |
| * refer enum ath10k_hw_cc_wraparound_type. |
| */ |
| enum ath10k_hw_cc_wraparound_type cc_wraparound_type; |
| |
| /* Some of chip expects fragment descriptor to be continuous |
| * memory for any TX operation. Set continuous_frag_desc flag |
| * for the hardware which have such requirement. |
| */ |
| bool continuous_frag_desc; |
| |
| /* CCK hardware rate table mapping for the newer chipsets |
| * like QCA99X0, QCA4019 got revised. The CCK h/w rate values |
| * are in a proper order with respect to the rate/preamble |
| */ |
| bool cck_rate_map_rev2; |
| |
| u32 channel_counters_freq_hz; |
| |
| /* Mgmt tx descriptors threshold for limiting probe response |
| * frames. |
| */ |
| u32 max_probe_resp_desc_thres; |
| |
| u32 tx_chain_mask; |
| u32 rx_chain_mask; |
| u32 max_spatial_stream; |
| u32 cal_data_len; |
| |
| struct ath10k_hw_params_fw { |
| const char *dir; |
| const char *board; |
| size_t board_size; |
| size_t board_ext_size; |
| } fw; |
| |
| /* qca99x0 family chips deliver broadcast/multicast management |
| * frames encrypted and expect software do decryption. |
| */ |
| bool sw_decrypt_mcast_mgmt; |
| |
| const struct ath10k_hw_ops *hw_ops; |
| |
| /* Number of bytes used for alignment in rx_hdr_status of rx desc. */ |
| int decap_align_bytes; |
| |
| /* hw specific clock control parameters */ |
| const struct ath10k_hw_clk_params *hw_clk; |
| int target_cpu_freq; |
| |
| /* Number of bytes to be discarded for each FFT sample */ |
| int spectral_bin_discard; |
| |
| /* The board may have a restricted NSS for 160 or 80+80 vs what it |
| * can do for 80Mhz. |
| */ |
| int vht160_mcs_rx_highest; |
| int vht160_mcs_tx_highest; |
| }; |
| |
| struct htt_rx_desc; |
| |
| /* Defines needed for Rx descriptor abstraction */ |
| struct ath10k_hw_ops { |
| int (*rx_desc_get_l3_pad_bytes)(struct htt_rx_desc *rxd); |
| void (*set_coverage_class)(struct ath10k *ar, s16 value); |
| int (*enable_pll_clk)(struct ath10k *ar); |
| }; |
| |
| extern const struct ath10k_hw_ops qca988x_ops; |
| extern const struct ath10k_hw_ops qca99x0_ops; |
| extern const struct ath10k_hw_ops qca6174_ops; |
| |
| extern const struct ath10k_hw_clk_params qca6174_clk[]; |
| |
| static inline int |
| ath10k_rx_desc_get_l3_pad_bytes(struct ath10k_hw_params *hw, |
| struct htt_rx_desc *rxd) |
| { |
| if (hw->hw_ops->rx_desc_get_l3_pad_bytes) |
| return hw->hw_ops->rx_desc_get_l3_pad_bytes(rxd); |
| return 0; |
| } |
| |
| /* Target specific defines for MAIN firmware */ |
| #define TARGET_NUM_VDEVS 8 |
| #define TARGET_NUM_PEER_AST 2 |
| #define TARGET_NUM_WDS_ENTRIES 32 |
| #define TARGET_DMA_BURST_SIZE 0 |
| #define TARGET_MAC_AGGR_DELIM 0 |
| #define TARGET_AST_SKID_LIMIT 16 |
| #define TARGET_NUM_STATIONS 16 |
| #define TARGET_NUM_PEERS ((TARGET_NUM_STATIONS) + \ |
| (TARGET_NUM_VDEVS)) |
| #define TARGET_NUM_OFFLOAD_PEERS 0 |
| #define TARGET_NUM_OFFLOAD_REORDER_BUFS 0 |
| #define TARGET_NUM_PEER_KEYS 2 |
| #define TARGET_NUM_TIDS ((TARGET_NUM_PEERS) * 2) |
| #define TARGET_TX_CHAIN_MASK (BIT(0) | BIT(1) | BIT(2)) |
| #define TARGET_RX_CHAIN_MASK (BIT(0) | BIT(1) | BIT(2)) |
| #define TARGET_RX_TIMEOUT_LO_PRI 100 |
| #define TARGET_RX_TIMEOUT_HI_PRI 40 |
| |
| #define TARGET_SCAN_MAX_PENDING_REQS 4 |
| #define TARGET_BMISS_OFFLOAD_MAX_VDEV 3 |
| #define TARGET_ROAM_OFFLOAD_MAX_VDEV 3 |
| #define TARGET_ROAM_OFFLOAD_MAX_AP_PROFILES 8 |
| #define TARGET_GTK_OFFLOAD_MAX_VDEV 3 |
| #define TARGET_NUM_MCAST_GROUPS 0 |
| #define TARGET_NUM_MCAST_TABLE_ELEMS 0 |
| #define TARGET_MCAST2UCAST_MODE ATH10K_MCAST2UCAST_DISABLED |
| #define TARGET_TX_DBG_LOG_SIZE 1024 |
| #define TARGET_RX_SKIP_DEFRAG_TIMEOUT_DUP_DETECTION_CHECK 0 |
| #define TARGET_VOW_CONFIG 0 |
| #define TARGET_NUM_MSDU_DESC (1024 + 400) |
| #define TARGET_MAX_FRAG_ENTRIES 0 |
| |
| /* Target specific defines for 10.X firmware */ |
| #define TARGET_10X_NUM_VDEVS 16 |
| #define TARGET_10X_NUM_PEER_AST 2 |
| #define TARGET_10X_NUM_WDS_ENTRIES 32 |
| #define TARGET_10X_DMA_BURST_SIZE 0 |
| #define TARGET_10X_MAC_AGGR_DELIM 0 |
| #define TARGET_10X_AST_SKID_LIMIT 128 |
| #define TARGET_10X_NUM_STATIONS 128 |
| #define TARGET_10X_TX_STATS_NUM_STATIONS 118 |
| #define TARGET_10X_NUM_PEERS ((TARGET_10X_NUM_STATIONS) + \ |
| (TARGET_10X_NUM_VDEVS)) |
| #define TARGET_10X_TX_STATS_NUM_PEERS ((TARGET_10X_TX_STATS_NUM_STATIONS) + \ |
| (TARGET_10X_NUM_VDEVS)) |
| #define TARGET_10X_NUM_OFFLOAD_PEERS 0 |
| #define TARGET_10X_NUM_OFFLOAD_REORDER_BUFS 0 |
| #define TARGET_10X_NUM_PEER_KEYS 2 |
| #define TARGET_10X_NUM_TIDS_MAX 256 |
| #define TARGET_10X_NUM_TIDS min((TARGET_10X_NUM_TIDS_MAX), \ |
| (TARGET_10X_NUM_PEERS) * 2) |
| #define TARGET_10X_TX_STATS_NUM_TIDS min((TARGET_10X_NUM_TIDS_MAX), \ |
| (TARGET_10X_TX_STATS_NUM_PEERS) * 2) |
| #define TARGET_10X_TX_CHAIN_MASK (BIT(0) | BIT(1) | BIT(2)) |
| #define TARGET_10X_RX_CHAIN_MASK (BIT(0) | BIT(1) | BIT(2)) |
| #define TARGET_10X_RX_TIMEOUT_LO_PRI 100 |
| #define TARGET_10X_RX_TIMEOUT_HI_PRI 40 |
| #define TARGET_10X_SCAN_MAX_PENDING_REQS 4 |
| #define TARGET_10X_BMISS_OFFLOAD_MAX_VDEV 2 |
| #define TARGET_10X_ROAM_OFFLOAD_MAX_VDEV 2 |
| #define TARGET_10X_ROAM_OFFLOAD_MAX_AP_PROFILES 8 |
| #define TARGET_10X_GTK_OFFLOAD_MAX_VDEV 3 |
| #define TARGET_10X_NUM_MCAST_GROUPS 0 |
| #define TARGET_10X_NUM_MCAST_TABLE_ELEMS 0 |
| #define TARGET_10X_MCAST2UCAST_MODE ATH10K_MCAST2UCAST_DISABLED |
| #define TARGET_10X_TX_DBG_LOG_SIZE 1024 |
| #define TARGET_10X_RX_SKIP_DEFRAG_TIMEOUT_DUP_DETECTION_CHECK 1 |
| #define TARGET_10X_VOW_CONFIG 0 |
| #define TARGET_10X_NUM_MSDU_DESC (1024 + 400) |
| #define TARGET_10X_MAX_FRAG_ENTRIES 0 |
| |
| /* 10.2 parameters */ |
| #define TARGET_10_2_DMA_BURST_SIZE 0 |
| |
| /* Target specific defines for WMI-TLV firmware */ |
| #define TARGET_TLV_NUM_VDEVS 4 |
| #define TARGET_TLV_NUM_STATIONS 32 |
| #define TARGET_TLV_NUM_PEERS 33 |
| #define TARGET_TLV_NUM_TDLS_VDEVS 1 |
| #define TARGET_TLV_NUM_TIDS ((TARGET_TLV_NUM_PEERS) * 2) |
| #define TARGET_TLV_NUM_MSDU_DESC (1024 + 32) |
| #define TARGET_TLV_NUM_WOW_PATTERNS 22 |
| |
| /* Diagnostic Window */ |
| #define CE_DIAG_PIPE 7 |
| |
| #define NUM_TARGET_CE_CONFIG_WLAN ar->hw_values->num_target_ce_config_wlan |
| |
| /* Target specific defines for 10.4 firmware */ |
| #define TARGET_10_4_NUM_VDEVS 16 |
| #define TARGET_10_4_NUM_STATIONS 32 |
| #define TARGET_10_4_NUM_PEERS ((TARGET_10_4_NUM_STATIONS) + \ |
| (TARGET_10_4_NUM_VDEVS)) |
| #define TARGET_10_4_ACTIVE_PEERS 0 |
| |
| #define TARGET_10_4_NUM_QCACHE_PEERS_MAX 512 |
| #define TARGET_10_4_QCACHE_ACTIVE_PEERS 50 |
| #define TARGET_10_4_QCACHE_ACTIVE_PEERS_PFC 35 |
| #define TARGET_10_4_NUM_OFFLOAD_PEERS 0 |
| #define TARGET_10_4_NUM_OFFLOAD_REORDER_BUFFS 0 |
| #define TARGET_10_4_NUM_PEER_KEYS 2 |
| #define TARGET_10_4_TGT_NUM_TIDS ((TARGET_10_4_NUM_PEERS) * 2) |
| #define TARGET_10_4_NUM_MSDU_DESC (1024 + 400) |
| #define TARGET_10_4_NUM_MSDU_DESC_PFC 2500 |
| #define TARGET_10_4_AST_SKID_LIMIT 32 |
| |
| /* 100 ms for video, best-effort, and background */ |
| #define TARGET_10_4_RX_TIMEOUT_LO_PRI 100 |
| |
| /* 40 ms for voice */ |
| #define TARGET_10_4_RX_TIMEOUT_HI_PRI 40 |
| |
| #define TARGET_10_4_RX_DECAP_MODE ATH10K_HW_TXRX_NATIVE_WIFI |
| #define TARGET_10_4_SCAN_MAX_REQS 4 |
| #define TARGET_10_4_BMISS_OFFLOAD_MAX_VDEV 3 |
| #define TARGET_10_4_ROAM_OFFLOAD_MAX_VDEV 3 |
| #define TARGET_10_4_ROAM_OFFLOAD_MAX_PROFILES 8 |
| |
| /* Note: mcast to ucast is disabled by default */ |
| #define TARGET_10_4_NUM_MCAST_GROUPS 0 |
| #define TARGET_10_4_NUM_MCAST_TABLE_ELEMS 0 |
| #define TARGET_10_4_MCAST2UCAST_MODE 0 |
| |
| #define TARGET_10_4_TX_DBG_LOG_SIZE 1024 |
| #define TARGET_10_4_NUM_WDS_ENTRIES 32 |
| #define TARGET_10_4_DMA_BURST_SIZE 1 |
| #define TARGET_10_4_MAC_AGGR_DELIM 0 |
| #define TARGET_10_4_RX_SKIP_DEFRAG_TIMEOUT_DUP_DETECTION_CHECK 1 |
| #define TARGET_10_4_VOW_CONFIG 0 |
| #define TARGET_10_4_GTK_OFFLOAD_MAX_VDEV 3 |
| #define TARGET_10_4_11AC_TX_MAX_FRAGS 2 |
| #define TARGET_10_4_MAX_PEER_EXT_STATS 16 |
| #define TARGET_10_4_SMART_ANT_CAP 0 |
| #define TARGET_10_4_BK_MIN_FREE 0 |
| #define TARGET_10_4_BE_MIN_FREE 0 |
| #define TARGET_10_4_VI_MIN_FREE 0 |
| #define TARGET_10_4_VO_MIN_FREE 0 |
| #define TARGET_10_4_RX_BATCH_MODE 1 |
| #define TARGET_10_4_THERMAL_THROTTLING_CONFIG 0 |
| #define TARGET_10_4_ATF_CONFIG 0 |
| #define TARGET_10_4_IPHDR_PAD_CONFIG 1 |
| #define TARGET_10_4_QWRAP_CONFIG 0 |
| |
| /* TDLS config */ |
| #define TARGET_10_4_NUM_TDLS_VDEVS 1 |
| #define TARGET_10_4_NUM_TDLS_BUFFER_STA 1 |
| #define TARGET_10_4_NUM_TDLS_SLEEP_STA 1 |
| |
| /* Maximum number of Copy Engine's supported */ |
| #define CE_COUNT_MAX 12 |
| |
| /* Number of Copy Engines supported */ |
| #define CE_COUNT ar->hw_values->ce_count |
| |
| /* |
| * Granted MSIs are assigned as follows: |
| * Firmware uses the first |
| * Remaining MSIs, if any, are used by Copy Engines |
| * This mapping is known to both Target firmware and Host software. |
| * It may be changed as long as Host and Target are kept in sync. |
| */ |
| /* MSI for firmware (errors, etc.) */ |
| #define MSI_ASSIGN_FW 0 |
| |
| /* MSIs for Copy Engines */ |
| #define MSI_ASSIGN_CE_INITIAL 1 |
| #define MSI_ASSIGN_CE_MAX ar->hw_values->msi_assign_ce_max |
| |
| /* as of IP3.7.1 */ |
| #define RTC_STATE_V_ON ar->hw_values->rtc_state_val_on |
| |
| #define RTC_STATE_V_LSB 0 |
| #define RTC_STATE_V_MASK 0x00000007 |
| #define RTC_STATE_ADDRESS 0x0000 |
| #define PCIE_SOC_WAKE_V_MASK 0x00000001 |
| #define PCIE_SOC_WAKE_ADDRESS 0x0004 |
| #define PCIE_SOC_WAKE_RESET 0x00000000 |
| #define SOC_GLOBAL_RESET_ADDRESS 0x0008 |
| |
| #define RTC_SOC_BASE_ADDRESS ar->regs->rtc_soc_base_address |
| #define RTC_WMAC_BASE_ADDRESS ar->regs->rtc_wmac_base_address |
| #define MAC_COEX_BASE_ADDRESS 0x00006000 |
| #define BT_COEX_BASE_ADDRESS 0x00007000 |
| #define SOC_PCIE_BASE_ADDRESS 0x00008000 |
| #define SOC_CORE_BASE_ADDRESS ar->regs->soc_core_base_address |
| #define WLAN_UART_BASE_ADDRESS 0x0000c000 |
| #define WLAN_SI_BASE_ADDRESS 0x00010000 |
| #define WLAN_GPIO_BASE_ADDRESS 0x00014000 |
| #define WLAN_ANALOG_INTF_BASE_ADDRESS 0x0001c000 |
| #define WLAN_MAC_BASE_ADDRESS ar->regs->wlan_mac_base_address |
| #define EFUSE_BASE_ADDRESS 0x00030000 |
| #define FPGA_REG_BASE_ADDRESS 0x00039000 |
| #define WLAN_UART2_BASE_ADDRESS 0x00054c00 |
| #define CE_WRAPPER_BASE_ADDRESS ar->regs->ce_wrapper_base_address |
| #define CE0_BASE_ADDRESS ar->regs->ce0_base_address |
| #define CE1_BASE_ADDRESS ar->regs->ce1_base_address |
| #define CE2_BASE_ADDRESS ar->regs->ce2_base_address |
| #define CE3_BASE_ADDRESS ar->regs->ce3_base_address |
| #define CE4_BASE_ADDRESS ar->regs->ce4_base_address |
| #define CE5_BASE_ADDRESS ar->regs->ce5_base_address |
| #define CE6_BASE_ADDRESS ar->regs->ce6_base_address |
| #define CE7_BASE_ADDRESS ar->regs->ce7_base_address |
| #define DBI_BASE_ADDRESS 0x00060000 |
| #define WLAN_ANALOG_INTF_PCIE_BASE_ADDRESS 0x0006c000 |
| #define PCIE_LOCAL_BASE_ADDRESS ar->regs->pcie_local_base_address |
| |
| #define SOC_RESET_CONTROL_ADDRESS 0x00000000 |
| #define SOC_RESET_CONTROL_OFFSET 0x00000000 |
| #define SOC_RESET_CONTROL_SI0_RST_MASK ar->regs->soc_reset_control_si0_rst_mask |
| #define SOC_RESET_CONTROL_CE_RST_MASK ar->regs->soc_reset_control_ce_rst_mask |
| #define SOC_RESET_CONTROL_CPU_WARM_RST_MASK 0x00000040 |
| #define SOC_CPU_CLOCK_OFFSET 0x00000020 |
| #define SOC_CPU_CLOCK_STANDARD_LSB 0 |
| #define SOC_CPU_CLOCK_STANDARD_MASK 0x00000003 |
| #define SOC_CLOCK_CONTROL_OFFSET 0x00000028 |
| #define SOC_CLOCK_CONTROL_SI0_CLK_MASK 0x00000001 |
| #define SOC_SYSTEM_SLEEP_OFFSET 0x000000c4 |
| #define SOC_LPO_CAL_OFFSET 0x000000e0 |
| #define SOC_LPO_CAL_ENABLE_LSB 20 |
| #define SOC_LPO_CAL_ENABLE_MASK 0x00100000 |
| #define SOC_LF_TIMER_CONTROL0_ADDRESS 0x00000050 |
| #define SOC_LF_TIMER_CONTROL0_ENABLE_MASK 0x00000004 |
| |
| #define SOC_CHIP_ID_ADDRESS ar->regs->soc_chip_id_address |
| #define SOC_CHIP_ID_REV_LSB 8 |
| #define SOC_CHIP_ID_REV_MASK 0x00000f00 |
| |
| #define WLAN_RESET_CONTROL_COLD_RST_MASK 0x00000008 |
| #define WLAN_RESET_CONTROL_WARM_RST_MASK 0x00000004 |
| #define WLAN_SYSTEM_SLEEP_DISABLE_LSB 0 |
| #define WLAN_SYSTEM_SLEEP_DISABLE_MASK 0x00000001 |
| |
| #define WLAN_GPIO_PIN0_ADDRESS 0x00000028 |
| #define WLAN_GPIO_PIN0_CONFIG_LSB 11 |
| #define WLAN_GPIO_PIN0_CONFIG_MASK 0x00007800 |
| #define WLAN_GPIO_PIN0_PAD_PULL_LSB 5 |
| #define WLAN_GPIO_PIN0_PAD_PULL_MASK 0x00000060 |
| #define WLAN_GPIO_PIN1_ADDRESS 0x0000002c |
| #define WLAN_GPIO_PIN1_CONFIG_MASK 0x00007800 |
| #define WLAN_GPIO_PIN10_ADDRESS 0x00000050 |
| #define WLAN_GPIO_PIN11_ADDRESS 0x00000054 |
| #define WLAN_GPIO_PIN12_ADDRESS 0x00000058 |
| #define WLAN_GPIO_PIN13_ADDRESS 0x0000005c |
| |
| #define CLOCK_GPIO_OFFSET 0xffffffff |
| #define CLOCK_GPIO_BT_CLK_OUT_EN_LSB 0 |
| #define CLOCK_GPIO_BT_CLK_OUT_EN_MASK 0 |
| |
| #define SI_CONFIG_OFFSET 0x00000000 |
| #define SI_CONFIG_ERR_INT_LSB 19 |
| #define SI_CONFIG_ERR_INT_MASK 0x00080000 |
| #define SI_CONFIG_BIDIR_OD_DATA_LSB 18 |
| #define SI_CONFIG_BIDIR_OD_DATA_MASK 0x00040000 |
| #define SI_CONFIG_I2C_LSB 16 |
| #define SI_CONFIG_I2C_MASK 0x00010000 |
| #define SI_CONFIG_POS_SAMPLE_LSB 7 |
| #define SI_CONFIG_POS_SAMPLE_MASK 0x00000080 |
| #define SI_CONFIG_INACTIVE_DATA_LSB 5 |
| #define SI_CONFIG_INACTIVE_DATA_MASK 0x00000020 |
| #define SI_CONFIG_INACTIVE_CLK_LSB 4 |
| #define SI_CONFIG_INACTIVE_CLK_MASK 0x00000010 |
| #define SI_CONFIG_DIVIDER_LSB 0 |
| #define SI_CONFIG_DIVIDER_MASK 0x0000000f |
| #define SI_CS_OFFSET 0x00000004 |
| #define SI_CS_DONE_ERR_LSB 10 |
| #define SI_CS_DONE_ERR_MASK 0x00000400 |
| #define SI_CS_DONE_INT_LSB 9 |
| #define SI_CS_DONE_INT_MASK 0x00000200 |
| #define SI_CS_START_LSB 8 |
| #define SI_CS_START_MASK 0x00000100 |
| #define SI_CS_RX_CNT_LSB 4 |
| #define SI_CS_RX_CNT_MASK 0x000000f0 |
| #define SI_CS_TX_CNT_LSB 0 |
| #define SI_CS_TX_CNT_MASK 0x0000000f |
| |
| #define SI_TX_DATA0_OFFSET 0x00000008 |
| #define SI_TX_DATA1_OFFSET 0x0000000c |
| #define SI_RX_DATA0_OFFSET 0x00000010 |
| #define SI_RX_DATA1_OFFSET 0x00000014 |
| |
| #define CORE_CTRL_CPU_INTR_MASK 0x00002000 |
| #define CORE_CTRL_PCIE_REG_31_MASK 0x00000800 |
| #define CORE_CTRL_ADDRESS 0x0000 |
| #define PCIE_INTR_ENABLE_ADDRESS 0x0008 |
| #define PCIE_INTR_CAUSE_ADDRESS 0x000c |
| #define PCIE_INTR_CLR_ADDRESS ar->regs->pcie_intr_clr_address |
| #define SCRATCH_3_ADDRESS ar->regs->scratch_3_address |
| #define CPU_INTR_ADDRESS 0x0010 |
| |
| #define CCNT_TO_MSEC(ar, x) ((x) / ar->hw_params.channel_counters_freq_hz) |
| |
| /* Firmware indications to the Host via SCRATCH_3 register. */ |
| #define FW_INDICATOR_ADDRESS ar->regs->fw_indicator_address |
| #define FW_IND_EVENT_PENDING 1 |
| #define FW_IND_INITIALIZED 2 |
| #define FW_IND_HOST_READY 0x80000000 |
| |
| /* HOST_REG interrupt from firmware */ |
| #define PCIE_INTR_FIRMWARE_MASK ar->regs->pcie_intr_fw_mask |
| #define PCIE_INTR_CE_MASK_ALL ar->regs->pcie_intr_ce_mask_all |
| |
| #define DRAM_BASE_ADDRESS 0x00400000 |
| |
| #define PCIE_BAR_REG_ADDRESS 0x40030 |
| |
| #define MISSING 0 |
| |
| #define SYSTEM_SLEEP_OFFSET SOC_SYSTEM_SLEEP_OFFSET |
| #define WLAN_SYSTEM_SLEEP_OFFSET SOC_SYSTEM_SLEEP_OFFSET |
| #define WLAN_RESET_CONTROL_OFFSET SOC_RESET_CONTROL_OFFSET |
| #define CLOCK_CONTROL_OFFSET SOC_CLOCK_CONTROL_OFFSET |
| #define CLOCK_CONTROL_SI0_CLK_MASK SOC_CLOCK_CONTROL_SI0_CLK_MASK |
| #define RESET_CONTROL_MBOX_RST_MASK MISSING |
| #define RESET_CONTROL_SI0_RST_MASK SOC_RESET_CONTROL_SI0_RST_MASK |
| #define GPIO_BASE_ADDRESS WLAN_GPIO_BASE_ADDRESS |
| #define GPIO_PIN0_OFFSET WLAN_GPIO_PIN0_ADDRESS |
| #define GPIO_PIN1_OFFSET WLAN_GPIO_PIN1_ADDRESS |
| #define GPIO_PIN0_CONFIG_LSB WLAN_GPIO_PIN0_CONFIG_LSB |
| #define GPIO_PIN0_CONFIG_MASK WLAN_GPIO_PIN0_CONFIG_MASK |
| #define GPIO_PIN0_PAD_PULL_LSB WLAN_GPIO_PIN0_PAD_PULL_LSB |
| #define GPIO_PIN0_PAD_PULL_MASK WLAN_GPIO_PIN0_PAD_PULL_MASK |
| #define GPIO_PIN1_CONFIG_MASK WLAN_GPIO_PIN1_CONFIG_MASK |
| #define SI_BASE_ADDRESS WLAN_SI_BASE_ADDRESS |
| #define SCRATCH_BASE_ADDRESS SOC_CORE_BASE_ADDRESS |
| #define LOCAL_SCRATCH_OFFSET 0x18 |
| #define CPU_CLOCK_OFFSET SOC_CPU_CLOCK_OFFSET |
| #define LPO_CAL_OFFSET SOC_LPO_CAL_OFFSET |
| #define GPIO_PIN10_OFFSET WLAN_GPIO_PIN10_ADDRESS |
| #define GPIO_PIN11_OFFSET WLAN_GPIO_PIN11_ADDRESS |
| #define GPIO_PIN12_OFFSET WLAN_GPIO_PIN12_ADDRESS |
| #define GPIO_PIN13_OFFSET WLAN_GPIO_PIN13_ADDRESS |
| #define CPU_CLOCK_STANDARD_LSB SOC_CPU_CLOCK_STANDARD_LSB |
| #define CPU_CLOCK_STANDARD_MASK SOC_CPU_CLOCK_STANDARD_MASK |
| #define LPO_CAL_ENABLE_LSB SOC_LPO_CAL_ENABLE_LSB |
| #define LPO_CAL_ENABLE_MASK SOC_LPO_CAL_ENABLE_MASK |
| #define ANALOG_INTF_BASE_ADDRESS WLAN_ANALOG_INTF_BASE_ADDRESS |
| #define MBOX_BASE_ADDRESS MISSING |
| #define INT_STATUS_ENABLE_ERROR_LSB MISSING |
| #define INT_STATUS_ENABLE_ERROR_MASK MISSING |
| #define INT_STATUS_ENABLE_CPU_LSB MISSING |
| #define INT_STATUS_ENABLE_CPU_MASK MISSING |
| #define INT_STATUS_ENABLE_COUNTER_LSB MISSING |
| #define INT_STATUS_ENABLE_COUNTER_MASK MISSING |
| #define INT_STATUS_ENABLE_MBOX_DATA_LSB MISSING |
| #define INT_STATUS_ENABLE_MBOX_DATA_MASK MISSING |
| #define ERROR_STATUS_ENABLE_RX_UNDERFLOW_LSB MISSING |
| #define ERROR_STATUS_ENABLE_RX_UNDERFLOW_MASK MISSING |
| #define ERROR_STATUS_ENABLE_TX_OVERFLOW_LSB MISSING |
| #define ERROR_STATUS_ENABLE_TX_OVERFLOW_MASK MISSING |
| #define COUNTER_INT_STATUS_ENABLE_BIT_LSB MISSING |
| #define COUNTER_INT_STATUS_ENABLE_BIT_MASK MISSING |
| #define INT_STATUS_ENABLE_ADDRESS MISSING |
| #define CPU_INT_STATUS_ENABLE_BIT_LSB MISSING |
| #define CPU_INT_STATUS_ENABLE_BIT_MASK MISSING |
| #define HOST_INT_STATUS_ADDRESS MISSING |
| #define CPU_INT_STATUS_ADDRESS MISSING |
| #define ERROR_INT_STATUS_ADDRESS MISSING |
| #define ERROR_INT_STATUS_WAKEUP_MASK MISSING |
| #define ERROR_INT_STATUS_WAKEUP_LSB MISSING |
| #define ERROR_INT_STATUS_RX_UNDERFLOW_MASK MISSING |
| #define ERROR_INT_STATUS_RX_UNDERFLOW_LSB MISSING |
| #define ERROR_INT_STATUS_TX_OVERFLOW_MASK MISSING |
| #define ERROR_INT_STATUS_TX_OVERFLOW_LSB MISSING |
| #define COUNT_DEC_ADDRESS MISSING |
| #define HOST_INT_STATUS_CPU_MASK MISSING |
| #define HOST_INT_STATUS_CPU_LSB MISSING |
| #define HOST_INT_STATUS_ERROR_MASK MISSING |
| #define HOST_INT_STATUS_ERROR_LSB MISSING |
| #define HOST_INT_STATUS_COUNTER_MASK MISSING |
| #define HOST_INT_STATUS_COUNTER_LSB MISSING |
| #define RX_LOOKAHEAD_VALID_ADDRESS MISSING |
| #define WINDOW_DATA_ADDRESS MISSING |
| #define WINDOW_READ_ADDR_ADDRESS MISSING |
| #define WINDOW_WRITE_ADDR_ADDRESS MISSING |
| |
| #define QCA9887_1_0_I2C_SDA_GPIO_PIN 5 |
| #define QCA9887_1_0_I2C_SDA_PIN_CONFIG 3 |
| #define QCA9887_1_0_SI_CLK_GPIO_PIN 17 |
| #define QCA9887_1_0_SI_CLK_PIN_CONFIG 3 |
| #define QCA9887_1_0_GPIO_ENABLE_W1TS_LOW_ADDRESS 0x00000010 |
| |
| #define QCA9887_EEPROM_SELECT_READ 0xa10000a0 |
| #define QCA9887_EEPROM_ADDR_HI_MASK 0x0000ff00 |
| #define QCA9887_EEPROM_ADDR_HI_LSB 8 |
| #define QCA9887_EEPROM_ADDR_LO_MASK 0x00ff0000 |
| #define QCA9887_EEPROM_ADDR_LO_LSB 16 |
| |
| #define MBOX_RESET_CONTROL_ADDRESS 0x00000000 |
| #define MBOX_HOST_INT_STATUS_ADDRESS 0x00000800 |
| #define MBOX_HOST_INT_STATUS_ERROR_LSB 7 |
| #define MBOX_HOST_INT_STATUS_ERROR_MASK 0x00000080 |
| #define MBOX_HOST_INT_STATUS_CPU_LSB 6 |
| #define MBOX_HOST_INT_STATUS_CPU_MASK 0x00000040 |
| #define MBOX_HOST_INT_STATUS_COUNTER_LSB 4 |
| #define MBOX_HOST_INT_STATUS_COUNTER_MASK 0x00000010 |
| #define MBOX_CPU_INT_STATUS_ADDRESS 0x00000801 |
| #define MBOX_ERROR_INT_STATUS_ADDRESS 0x00000802 |
| #define MBOX_ERROR_INT_STATUS_WAKEUP_LSB 2 |
| #define MBOX_ERROR_INT_STATUS_WAKEUP_MASK 0x00000004 |
| #define MBOX_ERROR_INT_STATUS_RX_UNDERFLOW_LSB 1 |
| #define MBOX_ERROR_INT_STATUS_RX_UNDERFLOW_MASK 0x00000002 |
| #define MBOX_ERROR_INT_STATUS_TX_OVERFLOW_LSB 0 |
| #define MBOX_ERROR_INT_STATUS_TX_OVERFLOW_MASK 0x00000001 |
| #define MBOX_COUNTER_INT_STATUS_ADDRESS 0x00000803 |
| #define MBOX_COUNTER_INT_STATUS_COUNTER_LSB 0 |
| #define MBOX_COUNTER_INT_STATUS_COUNTER_MASK 0x000000ff |
| #define MBOX_RX_LOOKAHEAD_VALID_ADDRESS 0x00000805 |
| #define MBOX_INT_STATUS_ENABLE_ADDRESS 0x00000828 |
| #define MBOX_INT_STATUS_ENABLE_ERROR_LSB 7 |
| #define MBOX_INT_STATUS_ENABLE_ERROR_MASK 0x00000080 |
| #define MBOX_INT_STATUS_ENABLE_CPU_LSB 6 |
| #define MBOX_INT_STATUS_ENABLE_CPU_MASK 0x00000040 |
| #define MBOX_INT_STATUS_ENABLE_INT_LSB 5 |
| #define MBOX_INT_STATUS_ENABLE_INT_MASK 0x00000020 |
| #define MBOX_INT_STATUS_ENABLE_COUNTER_LSB 4 |
| #define MBOX_INT_STATUS_ENABLE_COUNTER_MASK 0x00000010 |
| #define MBOX_INT_STATUS_ENABLE_MBOX_DATA_LSB 0 |
| #define MBOX_INT_STATUS_ENABLE_MBOX_DATA_MASK 0x0000000f |
| #define MBOX_CPU_INT_STATUS_ENABLE_ADDRESS 0x00000819 |
| #define MBOX_CPU_INT_STATUS_ENABLE_BIT_LSB 0 |
| #define MBOX_CPU_INT_STATUS_ENABLE_BIT_MASK 0x000000ff |
| #define MBOX_ERROR_STATUS_ENABLE_ADDRESS 0x0000081a |
| #define MBOX_ERROR_STATUS_ENABLE_RX_UNDERFLOW_LSB 1 |
| #define MBOX_ERROR_STATUS_ENABLE_RX_UNDERFLOW_MASK 0x00000002 |
| #define MBOX_ERROR_STATUS_ENABLE_TX_OVERFLOW_LSB 0 |
| #define MBOX_ERROR_STATUS_ENABLE_TX_OVERFLOW_MASK 0x00000001 |
| #define MBOX_COUNTER_INT_STATUS_ENABLE_ADDRESS 0x0000081b |
| #define MBOX_COUNTER_INT_STATUS_ENABLE_BIT_LSB 0 |
| #define MBOX_COUNTER_INT_STATUS_ENABLE_BIT_MASK 0x000000ff |
| #define MBOX_COUNT_ADDRESS 0x00000820 |
| #define MBOX_COUNT_DEC_ADDRESS 0x00000840 |
| #define MBOX_WINDOW_DATA_ADDRESS 0x00000874 |
| #define MBOX_WINDOW_WRITE_ADDR_ADDRESS 0x00000878 |
| #define MBOX_WINDOW_READ_ADDR_ADDRESS 0x0000087c |
| #define MBOX_CPU_DBG_SEL_ADDRESS 0x00000883 |
| #define MBOX_CPU_DBG_ADDRESS 0x00000884 |
| #define MBOX_RTC_BASE_ADDRESS 0x00000000 |
| #define MBOX_GPIO_BASE_ADDRESS 0x00005000 |
| #define MBOX_MBOX_BASE_ADDRESS 0x00008000 |
| |
| #define RTC_STATE_V_GET(x) (((x) & RTC_STATE_V_MASK) >> RTC_STATE_V_LSB) |
| |
| /* Register definitions for first generation ath10k cards. These cards include |
| * a mac thich has a register allocation similar to ath9k and at least some |
| * registers including the ones relevant for modifying the coverage class are |
| * identical to the ath9k definitions. |
| * These registers are usually managed by the ath10k firmware. However by |
| * overriding them it is possible to support coverage class modifications. |
| */ |
| #define WAVE1_PCU_ACK_CTS_TIMEOUT 0x8014 |
| #define WAVE1_PCU_ACK_CTS_TIMEOUT_MAX 0x00003FFF |
| #define WAVE1_PCU_ACK_CTS_TIMEOUT_ACK_MASK 0x00003FFF |
| #define WAVE1_PCU_ACK_CTS_TIMEOUT_ACK_LSB 0 |
| #define WAVE1_PCU_ACK_CTS_TIMEOUT_CTS_MASK 0x3FFF0000 |
| #define WAVE1_PCU_ACK_CTS_TIMEOUT_CTS_LSB 16 |
| |
| #define WAVE1_PCU_GBL_IFS_SLOT 0x1070 |
| #define WAVE1_PCU_GBL_IFS_SLOT_MASK 0x0000FFFF |
| #define WAVE1_PCU_GBL_IFS_SLOT_MAX 0x0000FFFF |
| #define WAVE1_PCU_GBL_IFS_SLOT_LSB 0 |
| #define WAVE1_PCU_GBL_IFS_SLOT_RESV0 0xFFFF0000 |
| |
| #define WAVE1_PHYCLK 0x801C |
| #define WAVE1_PHYCLK_USEC_MASK 0x0000007F |
| #define WAVE1_PHYCLK_USEC_LSB 0 |
| |
| /* qca6174 PLL offset/mask */ |
| #define SOC_CORE_CLK_CTRL_OFFSET 0x00000114 |
| #define SOC_CORE_CLK_CTRL_DIV_LSB 0 |
| #define SOC_CORE_CLK_CTRL_DIV_MASK 0x00000007 |
| |
| #define EFUSE_OFFSET 0x0000032c |
| #define EFUSE_XTAL_SEL_LSB 8 |
| #define EFUSE_XTAL_SEL_MASK 0x00000700 |
| |
| #define BB_PLL_CONFIG_OFFSET 0x000002f4 |
| #define BB_PLL_CONFIG_FRAC_LSB 0 |
| #define BB_PLL_CONFIG_FRAC_MASK 0x0003ffff |
| #define BB_PLL_CONFIG_OUTDIV_LSB 18 |
| #define BB_PLL_CONFIG_OUTDIV_MASK 0x001c0000 |
| |
| #define WLAN_PLL_SETTLE_OFFSET 0x0018 |
| #define WLAN_PLL_SETTLE_TIME_LSB 0 |
| #define WLAN_PLL_SETTLE_TIME_MASK 0x000007ff |
| |
| #define WLAN_PLL_CONTROL_OFFSET 0x0014 |
| #define WLAN_PLL_CONTROL_DIV_LSB 0 |
| #define WLAN_PLL_CONTROL_DIV_MASK 0x000003ff |
| #define WLAN_PLL_CONTROL_REFDIV_LSB 10 |
| #define WLAN_PLL_CONTROL_REFDIV_MASK 0x00003c00 |
| #define WLAN_PLL_CONTROL_BYPASS_LSB 16 |
| #define WLAN_PLL_CONTROL_BYPASS_MASK 0x00010000 |
| #define WLAN_PLL_CONTROL_NOPWD_LSB 18 |
| #define WLAN_PLL_CONTROL_NOPWD_MASK 0x00040000 |
| |
| #define RTC_SYNC_STATUS_OFFSET 0x0244 |
| #define RTC_SYNC_STATUS_PLL_CHANGING_LSB 5 |
| #define RTC_SYNC_STATUS_PLL_CHANGING_MASK 0x00000020 |
| /* qca6174 PLL offset/mask end */ |
| |
| #endif /* _HW_H_ */ |