serverworks: PIO mode setup fixes
* limit max PIO mode to PIO4, this driver doesn't support PIO5 and attempt
to program PIO5 by svwks_tune_chipset() could result in incorrect PIO
timings being programmed and possibly the data corruption (it seems that
the minimum possible values were used but I lack the datasheets to be sure)
* select best PIO mode in svwks_tune_drive() and not in svwks_tune_chipset()
when doing PIO autotuning (pio == 255)
* don't try to tune PIO in config_chipset_for_dma() as ide_dma_enable() could
return 1 if DMA was previously enabled (svwks_config_drive_xfer_rate()
takes care of PIO tuning if no suitable DMA mode is found)
* remove config_chipset_for_pio() and use svwks_tune_drive() instead,
config_chipset_for_pio() contained numerous bugs when selecting PIO mode
(luckily it was only used for devices limited to PIO by capabilities/BIOS):
- it didn't check for validity of id->eide_pio_modes and id->eide_pio_iordy
before using them
- it tried to found out maximum PIO mode basing on minimum IORDY cycle time
(moreover wrong cycle times were used for PIO0/1/5)
- it was overriding PIO blacklist and conservative PIO "downgrade" done
by ide_get_best_pio_mode()
- if the max drive PIO was PIO5 then XFER_PIO_0/XFER_PIO_SLOW was selected
(XFER_PIO_SLOW is not supported by svwks_tune_chipset() so the result
was the same as if using XFER_PIO_5 => wrong PIO timings were set)
- it was overriding drive->current_speed
* bump driver version
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
diff --git a/drivers/ide/pci/serverworks.c b/drivers/ide/pci/serverworks.c
index 2fa6d92..a94e77d 100644
--- a/drivers/ide/pci/serverworks.c
+++ b/drivers/ide/pci/serverworks.c
@@ -1,9 +1,10 @@
/*
- * linux/drivers/ide/pci/serverworks.c Version 0.8 25 Ebr 2003
+ * linux/drivers/ide/pci/serverworks.c Version 0.9 Mar 4 2007
*
* Copyright (C) 1998-2000 Michel Aubry
* Copyright (C) 1998-2000 Andrzej Krzysztofowicz
* Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
+ * Copyright (C) 2007 Bartlomiej Zolnierkiewicz
* Portions copyright (c) 2001 Sun Microsystems
*
*
@@ -136,19 +137,14 @@
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
- u8 speed;
- u8 pio = ide_get_best_pio_mode(drive, 255, 5, NULL);
+ u8 speed = ide_rate_filter(drive, xferspeed);
+ u8 pio = ide_get_best_pio_mode(drive, 255, 4, NULL);
u8 unit = (drive->select.b.unit & 0x01);
u8 csb5 = svwks_csb_check(dev);
u8 ultra_enable = 0, ultra_timing = 0;
u8 dma_timing = 0, pio_timing = 0;
u16 csb5_pio = 0;
- if (xferspeed == 255) /* PIO auto-tuning */
- speed = XFER_PIO_0 + pio;
- else
- speed = ide_rate_filter(drive, xferspeed);
-
/* If we are about to put a disk into UDMA mode we screwed up.
Our code assumes we never _ever_ do this on an OSB4 */
@@ -231,6 +227,9 @@
case XFER_MW_DMA_2:
case XFER_MW_DMA_1:
case XFER_MW_DMA_0:
+ /*
+ * TODO: always setup PIO mode so this won't be needed
+ */
pio_timing |= pio_modes[pio];
csb5_pio |= (pio << (4*drive->dn));
dma_timing |= dma_modes[speed - XFER_MW_DMA_0];
@@ -242,6 +241,9 @@
case XFER_UDMA_2:
case XFER_UDMA_1:
case XFER_UDMA_0:
+ /*
+ * TODO: always setup PIO mode so this won't be needed
+ */
pio_timing |= pio_modes[pio];
csb5_pio |= (pio << (4*drive->dn));
dma_timing |= dma_modes[2];
@@ -262,58 +264,18 @@
return (ide_config_drive_speed(drive, speed));
}
-static void config_chipset_for_pio (ide_drive_t *drive)
-{
- u16 eide_pio_timing[6] = {960, 480, 240, 180, 120, 90};
- u16 xfer_pio = drive->id->eide_pio_modes;
- u8 timing, speed, pio;
-
- pio = ide_get_best_pio_mode(drive, 255, 5, NULL);
-
- if (xfer_pio > 4)
- xfer_pio = 0;
-
- if (drive->id->eide_pio_iordy > 0)
- for (xfer_pio = 5;
- xfer_pio>0 &&
- drive->id->eide_pio_iordy>eide_pio_timing[xfer_pio];
- xfer_pio--);
- else
- xfer_pio = (drive->id->eide_pio_modes & 4) ? 0x05 :
- (drive->id->eide_pio_modes & 2) ? 0x04 :
- (drive->id->eide_pio_modes & 1) ? 0x03 :
- (drive->id->tPIO & 2) ? 0x02 :
- (drive->id->tPIO & 1) ? 0x01 : xfer_pio;
-
- timing = (xfer_pio >= pio) ? xfer_pio : pio;
-
- switch(timing) {
- case 4: speed = XFER_PIO_4;break;
- case 3: speed = XFER_PIO_3;break;
- case 2: speed = XFER_PIO_2;break;
- case 1: speed = XFER_PIO_1;break;
- default:
- speed = (!drive->id->tPIO) ? XFER_PIO_0 : XFER_PIO_SLOW;
- break;
- }
- (void) svwks_tune_chipset(drive, speed);
- drive->current_speed = speed;
-}
-
static void svwks_tune_drive (ide_drive_t *drive, u8 pio)
{
- if(pio == 255)
- (void) svwks_tune_chipset(drive, 255);
- else
- (void) svwks_tune_chipset(drive, (XFER_PIO_0 + pio));
+ pio = ide_get_best_pio_mode(drive, pio, 4, NULL);
+ (void)svwks_tune_chipset(drive, XFER_PIO_0 + pio);
}
static int config_chipset_for_dma (ide_drive_t *drive)
{
u8 speed = ide_max_dma_mode(drive);
- if (!(speed))
- speed = XFER_PIO_0 + ide_get_best_pio_mode(drive, 255, 5, NULL);
+ if (!speed)
+ return 0;
(void) svwks_tune_chipset(drive, speed);
return ide_dma_enable(drive);
@@ -327,7 +289,7 @@
return 0;
if (ide_use_fast_pio(drive))
- config_chipset_for_pio(drive);
+ svwks_tune_drive(drive, 255);
return -1;
}