ide: ide_get_best_pio_mode() returns incorrect IORDY setting (take 2)
The function ide_get_best_pio_mode() fails to return the correct IORDY setting
for the explicitly specified modes -- fix this along with the heading comment,
and also remove the long commented out code.
Also, while at it, correct the misliading comment about the PIO cycle time in
<linux/ide.h> -- it actually consists of only the active and recovery periods,
with only some chips also including the address setup time into equation...
[ bart: sl82c105 seems to be currently the only driver affected by this fix ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
diff --git a/drivers/ide/ide-lib.c b/drivers/ide/ide-lib.c
index 8afce4c..6871931 100644
--- a/drivers/ide/ide-lib.c
+++ b/drivers/ide/ide-lib.c
@@ -345,16 +345,16 @@
/**
* ide_get_best_pio_mode - get PIO mode from drive
- * @driver: drive to consider
+ * @drive: drive to consider
* @mode_wanted: preferred mode
- * @max_mode: highest allowed
- * @d: pio data
+ * @max_mode: highest allowed mode
+ * @d: PIO data
*
* This routine returns the recommended PIO settings for a given drive,
* based on the drive->id information and the ide_pio_blacklist[].
- * This is used by most chipset support modules when "auto-tuning".
*
- * Drive PIO mode auto selection
+ * Drive PIO mode is auto-selected if 255 is passed as mode_wanted.
+ * This is used by most chipset support modules when "auto-tuning".
*/
u8 ide_get_best_pio_mode (ide_drive_t *drive, u8 mode_wanted, u8 max_mode, ide_pio_data_t *d)
@@ -367,6 +367,7 @@
if (mode_wanted != 255) {
pio_mode = mode_wanted;
+ use_iordy = (pio_mode > 2);
} else if (!drive->id) {
pio_mode = 0;
} else if ((pio_mode = ide_scan_pio_blacklist(id->model)) != -1) {
@@ -396,19 +397,12 @@
}
}
-#if 0
- if (drive->id->major_rev_num & 0x0004) printk("ATA-2 ");
-#endif
-
/*
* Conservative "downgrade" for all pre-ATA2 drives
*/
if (pio_mode && pio_mode < 4) {
pio_mode--;
overridden = 1;
-#if 0
- use_iordy = (pio_mode > 2);
-#endif
if (cycle_time && cycle_time < ide_pio_timings[pio_mode].cycle_time)
cycle_time = 0; /* use standard timing */
}
diff --git a/include/linux/ide.h b/include/linux/ide.h
index 79c0282..34f2676 100644
--- a/include/linux/ide.h
+++ b/include/linux/ide.h
@@ -1359,7 +1359,8 @@
typedef struct ide_pio_timings_s {
int setup_time; /* Address setup (ns) minimum */
int active_time; /* Active pulse (ns) minimum */
- int cycle_time; /* Cycle time (ns) minimum = (setup + active + recovery) */
+ int cycle_time; /* Cycle time (ns) minimum = */
+ /* active + recovery (+ setup for some chips) */
} ide_pio_timings_t;
typedef struct ide_pio_data_s {