Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: (47 commits)
Blackfin: bfin_spi.h: add MMR peripheral layout
Blackfin: bfin_ppi.h: start a common PPI/EPPI header
Blackfin: bfin_can.h: add missing VERSION/VERSION2 MMRs
Blackfin: bf538: add missing SIC_RVECT define
Blackfin: bf561: rewrite SICA_xxx to just SIC_xxx
Blackfin: bf54x: add missing SIC_RVECT definition
Blackfin: H8606: move 8250 irqflags to platform resources
Blackfin: glue XIP/ROM kernel kconfigs
Blackfin: update sparse flags for latest upstream changes
Blackfin: coreb: update ioctl numbers
Blackfin: coreb: add gpl module license
Blackfin: bf518-ezkit: add ssm2603 codec resources
Blackfin: bf51x/bf52x: fix 16/32bit SPORT MMR helpers
Blackfin: tll6527m: new board port
Blackfin: bf526-ezbrd/bf527-ezkit: add NAND partition for u-boot
Blackfin: merge kernel init memory back into main memory region
Blackfin: gpio: add peripheral group check
Blackfin: dma: bf54x: add missing break for SPORT1 TX IRQ
Blackfin: add new cacheflush syscall
Blackfin: bf548-ezkit: increase u-boot partition size
...
diff --git a/arch/blackfin/Kconfig b/arch/blackfin/Kconfig
index 5a3152b..d9a1cb7 100644
--- a/arch/blackfin/Kconfig
+++ b/arch/blackfin/Kconfig
@@ -300,7 +300,7 @@
config BF_REV_0_2
bool "0.2"
- depends on (BF52x || BF537 || BF536 || BF534 || (BF54x && !BF54xM))
+ depends on (BF51x || BF52x || BF537 || BF536 || BF534 || (BF54x && !BF54xM))
config BF_REV_0_3
bool "0.3"
@@ -356,7 +356,7 @@
config MEM_MT48LC32M16A2TG_75
bool
- depends on (BFIN527_EZKIT || BFIN527_EZKIT_V2 || BFIN532_IP0X || BLACKSTAMP)
+ depends on (BFIN527_EZKIT || BFIN527_EZKIT_V2 || BFIN532_IP0X || BLACKSTAMP || BFIN527_AD7160EVAL)
default y
config MEM_MT48H32M16LFCJ_75
@@ -426,6 +426,7 @@
default "25000000" # most people use this
default "27000000" if BFIN533_EZKIT
default "30000000" if BFIN561_EZKIT
+ default "24000000" if BFIN527_AD7160EVAL
help
The frequency of CLKIN crystal oscillator on the board in Hz.
Warning: This value should match the crystal on the board. Otherwise,
@@ -463,6 +464,7 @@
default "20" if (BFIN537_BLUETECHNIX_CM_E || BFIN537_BLUETECHNIX_CM_U || BFIN527_BLUETECHNIX_CM || BFIN561_BLUETECHNIX_CM)
default "20" if BFIN561_EZKIT
default "16" if (H8606_HVSISTEMAS || BLACKSTAMP || BFIN526_EZBRD || BFIN518F_EZBRD)
+ default "25" if BFIN527_AD7160EVAL
help
This controls the frequency of the on-chip PLL. This can be between 1 and 64.
PLL Frequency = (Crystal Frequency) * (this setting)
@@ -926,6 +928,12 @@
endchoice
+# Common code uses "ROMKERNEL" or "XIP_KERNEL", so define both
+config XIP_KERNEL
+ bool
+ default y
+ depends on ROMKERNEL
+
source "mm/Kconfig"
config BFIN_GPTIMERS
diff --git a/arch/blackfin/Makefile b/arch/blackfin/Makefile
index 3e65b0f..46738d4 100644
--- a/arch/blackfin/Makefile
+++ b/arch/blackfin/Makefile
@@ -101,9 +101,8 @@
KBUILD_AFLAGS += -mcpu=$(cpu-y)-$(rev-y)
# - we utilize the silicon rev from the toolchain, so move it over to the checkflags
-# - the l1_text attribute is Blackfin specific, so fake it out as used to kill warnings
CHECKFLAGS_SILICON = $(shell echo "" | $(CPP) $(KBUILD_CFLAGS) -dD - 2>/dev/null | awk '$$2 == "__SILICON_REVISION__" { print $$3 }')
-CHECKFLAGS += -D__SILICON_REVISION__=$(CHECKFLAGS_SILICON) -Dl1_text=__used__
+CHECKFLAGS += -D__SILICON_REVISION__=$(CHECKFLAGS_SILICON) -D__bfin__
head-y := arch/$(ARCH)/kernel/init_task.o
diff --git a/arch/blackfin/configs/BF527-AD7160-EVAL_defconfig b/arch/blackfin/configs/BF527-AD7160-EVAL_defconfig
new file mode 100644
index 0000000..08c55f6
--- /dev/null
+++ b/arch/blackfin/configs/BF527-AD7160-EVAL_defconfig
@@ -0,0 +1,105 @@
+CONFIG_EXPERIMENTAL=y
+CONFIG_SYSVIPC=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_BLK_DEV_INITRD=y
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_EMBEDDED=y
+# CONFIG_ELF_CORE is not set
+# CONFIG_AIO is not set
+CONFIG_SLAB=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_IOSCHED_DEADLINE is not set
+CONFIG_PREEMPT=y
+CONFIG_BF527=y
+CONFIG_BF_REV_0_2=y
+CONFIG_IRQ_TWI=7
+CONFIG_IRQ_PORTH_INTA=7
+CONFIG_IRQ_PORTH_INTB=7
+CONFIG_BFIN527_AD7160EVAL=y
+CONFIG_BF527_SPORT0_PORTF=y
+CONFIG_BF527_UART1_PORTG=y
+CONFIG_IRQ_USB_INT0=11
+CONFIG_IRQ_USB_INT1=11
+CONFIG_IRQ_USB_INT2=11
+CONFIG_IRQ_USB_DMA=11
+CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE="bootargs=root=/dev/mtdblock0 rw clkin_hz=24000000 earlyprintk=serial,uart0,57600 console=tty0 console=ttyBF0,57600"
+CONFIG_CLKIN_HZ=24000000
+CONFIG_HZ_300=y
+# CONFIG_CYCLES_CLOCKSOURCE is not set
+CONFIG_IP_CHECKSUM_L1=y
+CONFIG_SYSCALL_TAB_L1=y
+CONFIG_CPLB_SWITCH_TAB_L1=y
+CONFIG_BFIN_GPTIMERS=y
+CONFIG_C_CDPRIO=y
+CONFIG_BANK_1=0x5554
+CONFIG_BANK_3=0xFFC0
+CONFIG_BINFMT_FLAT=y
+CONFIG_BINFMT_ZFLAT=y
+CONFIG_NET=y
+CONFIG_UNIX=y
+# CONFIG_WIRELESS is not set
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+# CONFIG_MISC_DEVICES is not set
+# CONFIG_INPUT_MOUSEDEV is not set
+CONFIG_INPUT_EVDEV=y
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+CONFIG_TOUCHSCREEN_AD7160=y
+CONFIG_TOUCHSCREEN_AD7160_FW=y
+# CONFIG_SERIO is not set
+# CONFIG_BFIN_DMA_INTERFACE is not set
+# CONFIG_DEVKMEM is not set
+CONFIG_SERIAL_BFIN=y
+CONFIG_SERIAL_BFIN_CONSOLE=y
+CONFIG_SERIAL_BFIN_UART0=y
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_BFIN_OTP is not set
+# CONFIG_HW_RANDOM is not set
+CONFIG_I2C=y
+# CONFIG_I2C_HELPER_AUTO is not set
+CONFIG_I2C_ALGOBIT=y
+CONFIG_I2C_BLACKFIN_TWI=y
+CONFIG_I2C_BLACKFIN_TWI_CLK_KHZ=400
+CONFIG_SPI=y
+CONFIG_SPI_BFIN=y
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_SYSFS=y
+# CONFIG_HWMON is not set
+CONFIG_FB=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
+CONFIG_LOGO=y
+# CONFIG_LOGO_LINUX_MONO is not set
+# CONFIG_LOGO_LINUX_VGA16 is not set
+# CONFIG_LOGO_LINUX_CLUT224 is not set
+# CONFIG_LOGO_BLACKFIN_VGA16 is not set
+# CONFIG_HID_SUPPORT is not set
+CONFIG_USB_MUSB_HDRC=y
+CONFIG_USB_GADGET_MUSB_HDRC=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_VBUS_DRAW=500
+CONFIG_USB_G_SERIAL=y
+CONFIG_MMC=y
+CONFIG_MMC_SPI=y
+CONFIG_EXT2_FS=y
+# CONFIG_DNOTIFY is not set
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_DEBUG_KERNEL=y
+CONFIG_DETECT_HUNG_TASK=y
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_BFIN_NO_KERN_HWTRACE is not set
+CONFIG_EARLY_PRINTK=y
+CONFIG_CPLB_INFO=y
+CONFIG_SECURITY=y
+CONFIG_CRC_CCITT=m
diff --git a/arch/blackfin/configs/BF527-TLL6527M_defconfig b/arch/blackfin/configs/BF527-TLL6527M_defconfig
new file mode 100644
index 0000000..92ded5e
--- /dev/null
+++ b/arch/blackfin/configs/BF527-TLL6527M_defconfig
@@ -0,0 +1,180 @@
+CONFIG_EXPERIMENTAL=y
+CONFIG_LOCALVERSION="DEV_0-1_pre2010"
+CONFIG_SYSVIPC=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_BLK_DEV_INITRD=y
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_EMBEDDED=y
+# CONFIG_SYSCTL_SYSCALL is not set
+# CONFIG_ELF_CORE is not set
+# CONFIG_FUTEX is not set
+# CONFIG_SIGNALFD is not set
+# CONFIG_TIMERFD is not set
+# CONFIG_EVENTFD is not set
+# CONFIG_AIO is not set
+CONFIG_SLAB=y
+CONFIG_MMAP_ALLOW_UNINITIALIZED=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_LBDAF is not set
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_IOSCHED_DEADLINE is not set
+CONFIG_PREEMPT_VOLUNTARY=y
+CONFIG_BF527=y
+CONFIG_BF_REV_0_2=y
+CONFIG_BFIN527_TLL6527M=y
+CONFIG_BF527_UART1_PORTG=y
+CONFIG_IRQ_USB_INT0=11
+CONFIG_IRQ_USB_INT1=11
+CONFIG_IRQ_USB_INT2=11
+CONFIG_IRQ_USB_DMA=11
+CONFIG_BOOT_LOAD=0x400000
+# CONFIG_CYCLES_CLOCKSOURCE is not set
+# CONFIG_SCHEDULE_L1 is not set
+# CONFIG_MEMSET_L1 is not set
+# CONFIG_MEMCPY_L1 is not set
+# CONFIG_SYS_BFIN_SPINLOCK_L1 is not set
+CONFIG_NOMMU_INITIAL_TRIM_EXCESS=0
+CONFIG_BFIN_GPTIMERS=y
+CONFIG_DMA_UNCACHED_2M=y
+CONFIG_C_CDPRIO=y
+CONFIG_BANK_0=0xFFC2
+CONFIG_BANK_1=0xFFC2
+CONFIG_BANK_2=0xFFC2
+CONFIG_BANK_3=0xFFC2
+CONFIG_BINFMT_FLAT=y
+CONFIG_BINFMT_ZFLAT=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_PNP=y
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+# CONFIG_INET_DIAG is not set
+# CONFIG_IPV6 is not set
+CONFIG_IRDA=m
+CONFIG_IRLAN=m
+CONFIG_IRCOMM=m
+CONFIG_IRTTY_SIR=m
+CONFIG_BFIN_SIR=m
+CONFIG_BFIN_SIR0=y
+# CONFIG_WIRELESS is not set
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_FW_LOADER is not set
+CONFIG_MTD=y
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_CFI_INTELEXT=y
+CONFIG_MTD_RAM=y
+CONFIG_MTD_ROM=y
+CONFIG_MTD_COMPLEX_MAPPINGS=y
+CONFIG_MTD_GPIO_ADDR=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_SCSI=y
+# CONFIG_SCSI_PROC_FS is not set
+CONFIG_BLK_DEV_SD=y
+CONFIG_BLK_DEV_SR=m
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_NETDEVICES=y
+CONFIG_NET_ETHERNET=y
+CONFIG_BFIN_MAC=y
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+# CONFIG_WLAN is not set
+# CONFIG_INPUT_MOUSEDEV is not set
+CONFIG_INPUT_EVDEV=y
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+CONFIG_TOUCHSCREEN_AD7879=m
+CONFIG_INPUT_MISC=y
+CONFIG_INPUT_AD714X=y
+CONFIG_INPUT_ADXL34X=y
+# CONFIG_SERIO is not set
+CONFIG_BFIN_PPI=m
+CONFIG_BFIN_SIMPLE_TIMER=m
+CONFIG_BFIN_SPORT=m
+# CONFIG_CONSOLE_TRANSLATIONS is not set
+# CONFIG_DEVKMEM is not set
+CONFIG_BFIN_JTAG_COMM=m
+CONFIG_SERIAL_BFIN=y
+CONFIG_SERIAL_BFIN_CONSOLE=y
+CONFIG_SERIAL_BFIN_UART1=y
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_HW_RANDOM is not set
+CONFIG_I2C_CHARDEV=y
+# CONFIG_I2C_HELPER_AUTO is not set
+CONFIG_I2C_SMBUS=y
+CONFIG_I2C_BLACKFIN_TWI=y
+CONFIG_I2C_BLACKFIN_TWI_CLK_KHZ=100
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_SYSFS=y
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_BFIN_WDT=y
+CONFIG_MEDIA_SUPPORT=y
+CONFIG_VIDEO_DEV=y
+# CONFIG_MEDIA_TUNER_CUSTOMISE is not set
+CONFIG_VIDEO_HELPER_CHIPS_AUTO=y
+CONFIG_VIDEO_BLACKFIN_CAM=m
+CONFIG_OV9655=y
+CONFIG_FB=y
+CONFIG_BACKLIGHT_LCD_SUPPORT=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FONTS=y
+CONFIG_FONT_6x11=y
+CONFIG_LOGO=y
+# CONFIG_LOGO_LINUX_MONO is not set
+# CONFIG_LOGO_LINUX_VGA16 is not set
+# CONFIG_LOGO_LINUX_CLUT224 is not set
+# CONFIG_LOGO_BLACKFIN_VGA16 is not set
+CONFIG_SOUND=y
+CONFIG_SND=y
+CONFIG_SND_MIXER_OSS=y
+CONFIG_SND_PCM_OSS=y
+CONFIG_SND_SOC=y
+CONFIG_SND_BF5XX_I2S=y
+CONFIG_SND_BF5XX_SOC_SSM2602=y
+# CONFIG_HID_SUPPORT is not set
+# CONFIG_USB_SUPPORT is not set
+CONFIG_MMC=m
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_BFIN=y
+CONFIG_EXT2_FS=y
+# CONFIG_DNOTIFY is not set
+CONFIG_ISO9660_FS=m
+CONFIG_JOLIET=y
+CONFIG_UDF_FS=m
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_JFFS2_FS=y
+CONFIG_NFS_FS=m
+CONFIG_NFS_V3=y
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+CONFIG_NLS_CODEPAGE_437=m
+CONFIG_NLS_CODEPAGE_936=m
+CONFIG_NLS_ISO8859_1=m
+CONFIG_NLS_UTF8=m
+CONFIG_DEBUG_KERNEL=y
+CONFIG_DEBUG_SHIRQ=y
+CONFIG_DETECT_HUNG_TASK=y
+CONFIG_DEBUG_INFO=y
+# CONFIG_RCU_CPU_STALL_DETECTOR is not set
+# CONFIG_FTRACE is not set
+CONFIG_DEBUG_MMRS=y
+CONFIG_DEBUG_HWERR=y
+CONFIG_EXACT_HWERR=y
+CONFIG_DEBUG_DOUBLEFAULT=y
+CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_ONE=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_CPLB_INFO=y
+CONFIG_SECURITY=y
+CONFIG_CRYPTO=y
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+CONFIG_CRC7=m
diff --git a/arch/blackfin/include/asm/Kbuild b/arch/blackfin/include/asm/Kbuild
index d9eb29e..9e7c537 100644
--- a/arch/blackfin/include/asm/Kbuild
+++ b/arch/blackfin/include/asm/Kbuild
@@ -1,4 +1,5 @@
include include/asm-generic/Kbuild.asm
header-y += bfin_sport.h
+header-y += cachectl.h
header-y += fixed_code.h
diff --git a/arch/blackfin/include/asm/bfin5xx_spi.h b/arch/blackfin/include/asm/bfin5xx_spi.h
index 4223cf0..0b5136e 100644
--- a/arch/blackfin/include/asm/bfin5xx_spi.h
+++ b/arch/blackfin/include/asm/bfin5xx_spi.h
@@ -41,6 +41,25 @@
#define BIT_STU_SENDOVER 0x0001
#define BIT_STU_RECVFULL 0x0020
+/*
+ * All Blackfin system MMRs are padded to 32bits even if the register
+ * itself is only 16bits. So use a helper macro to streamline this.
+ */
+#define __BFP(m) u16 m; u16 __pad_##m
+
+/*
+ * bfin spi registers layout
+ */
+struct bfin_spi_regs {
+ __BFP(ctl);
+ __BFP(flg);
+ __BFP(stat);
+ __BFP(tdbr);
+ __BFP(rdbr);
+ __BFP(baud);
+ __BFP(shadow);
+};
+
#define MAX_CTRL_CS 8 /* cs in spi controller */
/* device.platform_data for SSP controller devices */
diff --git a/arch/blackfin/include/asm/bfin_can.h b/arch/blackfin/include/asm/bfin_can.h
index eec0076..b1492e0 100644
--- a/arch/blackfin/include/asm/bfin_can.h
+++ b/arch/blackfin/include/asm/bfin_can.h
@@ -34,6 +34,7 @@
};
struct bfin_can_channel_regs {
+ /* data[0,2,4,6] -> data{0,1,2,3} while data[1,3,5,7] is padding */
u16 data[8];
__BFP(dlc);
__BFP(tsv);
@@ -83,16 +84,18 @@
__BFP(gif); /* offset 0x9c */
__BFP(control); /* offset 0xa0 */
__BFP(intr); /* offset 0xa4 */
- u32 __pad3[1];
+ __BFP(version); /* offset 0xa8 */
__BFP(mbtd); /* offset 0xac */
__BFP(ewr); /* offset 0xb0 */
__BFP(esr); /* offset 0xb4 */
- u32 __pad4[2];
+ u32 __pad3[2];
__BFP(ucreg); /* offset 0xc0 */
__BFP(uccnt); /* offset 0xc4 */
__BFP(ucrc); /* offset 0xc8 */
__BFP(uccnf); /* offset 0xcc */
- u32 __pad5[12];
+ u32 __pad4[1];
+ __BFP(version2); /* offset 0xd4 */
+ u32 __pad5[10];
/*
* channel(mailbox) mask and message registers
diff --git a/arch/blackfin/include/asm/bfin_ppi.h b/arch/blackfin/include/asm/bfin_ppi.h
new file mode 100644
index 0000000..0039008
--- /dev/null
+++ b/arch/blackfin/include/asm/bfin_ppi.h
@@ -0,0 +1,51 @@
+/*
+ * bfin_ppi.h - interface to Blackfin PPIs
+ *
+ * Copyright 2005-2010 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#ifndef __ASM_BFIN_PPI_H__
+#define __ASM_BFIN_PPI_H__
+
+#include <linux/types.h>
+
+/*
+ * All Blackfin system MMRs are padded to 32bits even if the register
+ * itself is only 16bits. So use a helper macro to streamline this.
+ */
+#define __BFP(m) u16 m; u16 __pad_##m
+
+/*
+ * bfin ppi registers layout
+ */
+struct bfin_ppi_regs {
+ __BFP(control);
+ __BFP(status);
+ __BFP(count);
+ __BFP(delay);
+ __BFP(frame);
+};
+
+/*
+ * bfin eppi registers layout
+ */
+struct bfin_eppi_regs {
+ __BFP(status);
+ __BFP(hcount);
+ __BFP(hdelay);
+ __BFP(vcount);
+ __BFP(vdelay);
+ __BFP(frame);
+ __BFP(line);
+ __BFP(clkdiv);
+ u32 control;
+ u32 fs1w_hbl;
+ u32 fs1p_avpl;
+ u32 fs2w_lvb;
+ u32 fs2p_lavf;
+ u32 clip;
+};
+
+#endif
diff --git a/arch/blackfin/include/asm/cachectl.h b/arch/blackfin/include/asm/cachectl.h
new file mode 100644
index 0000000..03255df
--- /dev/null
+++ b/arch/blackfin/include/asm/cachectl.h
@@ -0,0 +1,20 @@
+/*
+ * based on the mips/cachectl.h
+ *
+ * Copyright 2010 Analog Devices Inc.
+ * Copyright (C) 1994, 1995, 1996 by Ralf Baechle
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#ifndef _ASM_CACHECTL
+#define _ASM_CACHECTL
+
+/*
+ * Options for cacheflush system call
+ */
+#define ICACHE (1<<0) /* flush instruction cache */
+#define DCACHE (1<<1) /* writeback and flush data cache */
+#define BCACHE (ICACHE|DCACHE) /* flush both caches */
+
+#endif /* _ASM_CACHECTL */
diff --git a/arch/blackfin/include/asm/cdef_LPBlackfin.h b/arch/blackfin/include/asm/cdef_LPBlackfin.h
index 6c39d94..a1f6817 100644
--- a/arch/blackfin/include/asm/cdef_LPBlackfin.h
+++ b/arch/blackfin/include/asm/cdef_LPBlackfin.h
@@ -172,16 +172,19 @@
#define bfin_write_ICPLB_DATA14(val) bfin_write32(ICPLB_DATA14,val)
#define bfin_read_ICPLB_DATA15() bfin_read32(ICPLB_DATA15)
#define bfin_write_ICPLB_DATA15(val) bfin_write32(ICPLB_DATA15,val)
-#define bfin_read_ITEST_COMMAND() bfin_read32(ITEST_COMMAND)
#define bfin_write_ITEST_COMMAND(val) bfin_write32(ITEST_COMMAND,val)
#if 0
#define ITEST_INDEX 0xFFE01304 /* Instruction Test Index Register */
#endif
-#define bfin_read_ITEST_DATA0() bfin_read32(ITEST_DATA0)
#define bfin_write_ITEST_DATA0(val) bfin_write32(ITEST_DATA0,val)
-#define bfin_read_ITEST_DATA1() bfin_read32(ITEST_DATA1)
#define bfin_write_ITEST_DATA1(val) bfin_write32(ITEST_DATA1,val)
+#if ANOMALY_05000481
+#define bfin_read_ITEST_COMMAND() bfin_read32(ITEST_COMMAND)
+#define bfin_read_ITEST_DATA0() bfin_read32(ITEST_DATA0)
+#define bfin_read_ITEST_DATA1() bfin_read32(ITEST_DATA1)
+#endif
+
/* Event/Interrupt Registers*/
#define bfin_read_EVT0() bfin_read32(EVT0)
diff --git a/arch/blackfin/include/asm/ptrace.h b/arch/blackfin/include/asm/ptrace.h
index aaa1c6c..832d7c0 100644
--- a/arch/blackfin/include/asm/ptrace.h
+++ b/arch/blackfin/include/asm/ptrace.h
@@ -113,6 +113,9 @@
/* common code demands this function */
#define ptrace_disable(child) user_disable_single_step(child)
+extern int is_user_addr_valid(struct task_struct *child,
+ unsigned long start, unsigned long len);
+
/*
* Get the address of the live pt_regs for the specified task.
* These are saved onto the top kernel stack when the process
diff --git a/arch/blackfin/include/asm/serial.h b/arch/blackfin/include/asm/serial.h
index 94a4a12..a0cb0caf 100644
--- a/arch/blackfin/include/asm/serial.h
+++ b/arch/blackfin/include/asm/serial.h
@@ -1,2 +1 @@
#include <asm-generic/serial.h>
-#define SERIAL_EXTRA_IRQ_FLAGS IRQF_TRIGGER_HIGH
diff --git a/arch/blackfin/include/asm/unistd.h b/arch/blackfin/include/asm/unistd.h
index 14fcd25..928ae97 100644
--- a/arch/blackfin/include/asm/unistd.h
+++ b/arch/blackfin/include/asm/unistd.h
@@ -392,8 +392,9 @@
#define __NR_fanotify_init 371
#define __NR_fanotify_mark 372
#define __NR_prlimit64 373
+#define __NR_cacheflush 374
-#define __NR_syscall 374
+#define __NR_syscall 375
#define NR_syscalls __NR_syscall
/* Old optional stuff no one actually uses */
diff --git a/arch/blackfin/kernel/bfin_gpio.c b/arch/blackfin/kernel/bfin_gpio.c
index ca1c1f9..170cf90 100644
--- a/arch/blackfin/kernel/bfin_gpio.c
+++ b/arch/blackfin/kernel/bfin_gpio.c
@@ -1,7 +1,7 @@
/*
* GPIO Abstraction Layer
*
- * Copyright 2006-2009 Analog Devices Inc.
+ * Copyright 2006-2010 Analog Devices Inc.
*
* Licensed under the GPL-2 or later
*/
@@ -215,82 +215,91 @@
}
#ifdef BF537_FAMILY
-static struct {
- unsigned short res;
- unsigned short offset;
-} port_mux_lut[] = {
- {.res = P_PPI0_D13, .offset = 11},
- {.res = P_PPI0_D14, .offset = 11},
- {.res = P_PPI0_D15, .offset = 11},
- {.res = P_SPORT1_TFS, .offset = 11},
- {.res = P_SPORT1_TSCLK, .offset = 11},
- {.res = P_SPORT1_DTPRI, .offset = 11},
- {.res = P_PPI0_D10, .offset = 10},
- {.res = P_PPI0_D11, .offset = 10},
- {.res = P_PPI0_D12, .offset = 10},
- {.res = P_SPORT1_RSCLK, .offset = 10},
- {.res = P_SPORT1_RFS, .offset = 10},
- {.res = P_SPORT1_DRPRI, .offset = 10},
- {.res = P_PPI0_D8, .offset = 9},
- {.res = P_PPI0_D9, .offset = 9},
- {.res = P_SPORT1_DRSEC, .offset = 9},
- {.res = P_SPORT1_DTSEC, .offset = 9},
- {.res = P_TMR2, .offset = 8},
- {.res = P_PPI0_FS3, .offset = 8},
- {.res = P_TMR3, .offset = 7},
- {.res = P_SPI0_SSEL4, .offset = 7},
- {.res = P_TMR4, .offset = 6},
- {.res = P_SPI0_SSEL5, .offset = 6},
- {.res = P_TMR5, .offset = 5},
- {.res = P_SPI0_SSEL6, .offset = 5},
- {.res = P_UART1_RX, .offset = 4},
- {.res = P_UART1_TX, .offset = 4},
- {.res = P_TMR6, .offset = 4},
- {.res = P_TMR7, .offset = 4},
- {.res = P_UART0_RX, .offset = 3},
- {.res = P_UART0_TX, .offset = 3},
- {.res = P_DMAR0, .offset = 3},
- {.res = P_DMAR1, .offset = 3},
- {.res = P_SPORT0_DTSEC, .offset = 1},
- {.res = P_SPORT0_DRSEC, .offset = 1},
- {.res = P_CAN0_RX, .offset = 1},
- {.res = P_CAN0_TX, .offset = 1},
- {.res = P_SPI0_SSEL7, .offset = 1},
- {.res = P_SPORT0_TFS, .offset = 0},
- {.res = P_SPORT0_DTPRI, .offset = 0},
- {.res = P_SPI0_SSEL2, .offset = 0},
- {.res = P_SPI0_SSEL3, .offset = 0},
+static const s8 port_mux[] = {
+ [GPIO_PF0] = 3,
+ [GPIO_PF1] = 3,
+ [GPIO_PF2] = 4,
+ [GPIO_PF3] = 4,
+ [GPIO_PF4] = 5,
+ [GPIO_PF5] = 6,
+ [GPIO_PF6] = 7,
+ [GPIO_PF7] = 8,
+ [GPIO_PF8 ... GPIO_PF15] = -1,
+ [GPIO_PG0 ... GPIO_PG7] = -1,
+ [GPIO_PG8] = 9,
+ [GPIO_PG9] = 9,
+ [GPIO_PG10] = 10,
+ [GPIO_PG11] = 10,
+ [GPIO_PG12] = 10,
+ [GPIO_PG13] = 11,
+ [GPIO_PG14] = 11,
+ [GPIO_PG15] = 11,
+ [GPIO_PH0 ... GPIO_PH15] = -1,
+ [PORT_PJ0 ... PORT_PJ3] = -1,
+ [PORT_PJ4] = 1,
+ [PORT_PJ5] = 1,
+ [PORT_PJ6 ... PORT_PJ9] = -1,
+ [PORT_PJ10] = 0,
+ [PORT_PJ11] = 0,
};
+static int portmux_group_check(unsigned short per)
+{
+ u16 ident = P_IDENT(per);
+ u16 function = P_FUNCT2MUX(per);
+ s8 offset = port_mux[ident];
+ u16 m, pmux, pfunc;
+
+ if (offset < 0)
+ return 0;
+
+ pmux = bfin_read_PORT_MUX();
+ for (m = 0; m < ARRAY_SIZE(port_mux); ++m) {
+ if (m == ident)
+ continue;
+ if (port_mux[m] != offset)
+ continue;
+ if (!is_reserved(peri, m, 1))
+ continue;
+
+ if (offset == 1)
+ pfunc = (pmux >> offset) & 3;
+ else
+ pfunc = (pmux >> offset) & 1;
+ if (pfunc != function) {
+ pr_err("pin group conflict! request pin %d func %d conflict with pin %d func %d\n",
+ ident, function, m, pfunc);
+ return -EINVAL;
+ }
+ }
+
+ return 0;
+}
+
static void portmux_setup(unsigned short per)
{
- u16 y, offset, muxreg;
+ u16 ident = P_IDENT(per);
u16 function = P_FUNCT2MUX(per);
+ s8 offset = port_mux[ident];
+ u16 pmux;
- for (y = 0; y < ARRAY_SIZE(port_mux_lut); y++) {
- if (port_mux_lut[y].res == per) {
+ if (offset == -1)
+ return;
- /* SET PORTMUX REG */
-
- offset = port_mux_lut[y].offset;
- muxreg = bfin_read_PORT_MUX();
-
- if (offset != 1)
- muxreg &= ~(1 << offset);
- else
- muxreg &= ~(3 << 1);
-
- muxreg |= (function << offset);
- bfin_write_PORT_MUX(muxreg);
- }
- }
+ pmux = bfin_read_PORT_MUX();
+ if (offset != 1)
+ pmux &= ~(1 << offset);
+ else
+ pmux &= ~(3 << 1);
+ pmux |= (function << offset);
+ bfin_write_PORT_MUX(pmux);
}
#elif defined(CONFIG_BF54x)
inline void portmux_setup(unsigned short per)
{
- u32 pmux;
u16 ident = P_IDENT(per);
u16 function = P_FUNCT2MUX(per);
+ u32 pmux;
pmux = gpio_array[gpio_bank(ident)]->port_mux;
@@ -302,20 +311,54 @@
inline u16 get_portmux(unsigned short per)
{
- u32 pmux;
u16 ident = P_IDENT(per);
-
- pmux = gpio_array[gpio_bank(ident)]->port_mux;
-
+ u32 pmux = gpio_array[gpio_bank(ident)]->port_mux;
return (pmux >> (2 * gpio_sub_n(ident)) & 0x3);
}
+static int portmux_group_check(unsigned short per)
+{
+ return 0;
+}
#elif defined(CONFIG_BF52x) || defined(CONFIG_BF51x)
+static int portmux_group_check(unsigned short per)
+{
+ u16 ident = P_IDENT(per);
+ u16 function = P_FUNCT2MUX(per);
+ u8 offset = pmux_offset[gpio_bank(ident)][gpio_sub_n(ident)];
+ u16 pin, gpiopin, pfunc;
+
+ for (pin = 0; pin < GPIO_BANKSIZE; ++pin) {
+ if (offset != pmux_offset[gpio_bank(ident)][pin])
+ continue;
+
+ gpiopin = gpio_bank(ident) * GPIO_BANKSIZE + pin;
+ if (gpiopin == ident)
+ continue;
+ if (!is_reserved(peri, gpiopin, 1))
+ continue;
+
+ pfunc = *port_mux[gpio_bank(ident)];
+ pfunc = (pfunc >> offset) & 3;
+ if (pfunc != function) {
+ pr_err("pin group conflict! request pin %d func %d conflict with pin %d func %d\n",
+ ident, function, gpiopin, pfunc);
+ return -EINVAL;
+ }
+ }
+
+ return 0;
+}
+
inline void portmux_setup(unsigned short per)
{
- u16 pmux, ident = P_IDENT(per), function = P_FUNCT2MUX(per);
+ u16 ident = P_IDENT(per);
+ u16 function = P_FUNCT2MUX(per);
u8 offset = pmux_offset[gpio_bank(ident)][gpio_sub_n(ident)];
+ u16 pmux;
pmux = *port_mux[gpio_bank(ident)];
+ if (((pmux >> offset) & 3) == function)
+ return;
pmux &= ~(3 << offset);
pmux |= (function & 3) << offset;
*port_mux[gpio_bank(ident)] = pmux;
@@ -323,6 +366,10 @@
}
#else
# define portmux_setup(...) do { } while (0)
+static int portmux_group_check(unsigned short per)
+{
+ return 0;
+}
#endif
#ifndef CONFIG_BF54x
@@ -735,6 +782,10 @@
}
}
+ if (unlikely(portmux_group_check(per))) {
+ hard_local_irq_restore(flags);
+ return -EBUSY;
+ }
anyway:
reserve(peri, ident);
diff --git a/arch/blackfin/kernel/process.c b/arch/blackfin/kernel/process.c
index c86a3ed..cd0c090 100644
--- a/arch/blackfin/kernel/process.c
+++ b/arch/blackfin/kernel/process.c
@@ -493,6 +493,11 @@
return 1;
#endif
+#ifndef CONFIG_EXCEPTION_L1_SCRATCH
+ if (in_mem_const(addr, size, (unsigned long)l1_stack_base, l1_stack_len))
+ return 1;
+#endif
+
aret = in_async(addr, size);
if (aret < 2)
return aret;
diff --git a/arch/blackfin/kernel/ptrace.c b/arch/blackfin/kernel/ptrace.c
index 6ec7768..b358393 100644
--- a/arch/blackfin/kernel/ptrace.c
+++ b/arch/blackfin/kernel/ptrace.c
@@ -27,6 +27,7 @@
#include <asm/fixed_code.h>
#include <asm/cacheflush.h>
#include <asm/mem_map.h>
+#include <asm/mmu_context.h>
/*
* does not yet catch signals sent when the child dies.
@@ -113,8 +114,8 @@
/*
* check that an address falls within the bounds of the target process's memory mappings
*/
-static inline int is_user_addr_valid(struct task_struct *child,
- unsigned long start, unsigned long len)
+int
+is_user_addr_valid(struct task_struct *child, unsigned long start, unsigned long len)
{
struct vm_area_struct *vma;
struct sram_list_struct *sraml;
@@ -135,6 +136,13 @@
if (start >= FIXED_CODE_START && start + len < FIXED_CODE_END)
return 0;
+#ifdef CONFIG_APP_STACK_L1
+ if (child->mm->context.l1_stack_save)
+ if (start >= (unsigned long)l1_stack_base &&
+ start + len < (unsigned long)l1_stack_base + l1_stack_len)
+ return 0;
+#endif
+
return -EIO;
}
diff --git a/arch/blackfin/kernel/sys_bfin.c b/arch/blackfin/kernel/sys_bfin.c
index bdc1e2f..89448ed 100644
--- a/arch/blackfin/kernel/sys_bfin.c
+++ b/arch/blackfin/kernel/sys_bfin.c
@@ -21,6 +21,8 @@
#include <asm/cacheflush.h>
#include <asm/dma.h>
+#include <asm/cachectl.h>
+#include <asm/ptrace.h>
asmlinkage void *sys_sram_alloc(size_t size, unsigned long flags)
{
@@ -70,3 +72,16 @@
return ret;
}
+
+SYSCALL_DEFINE3(cacheflush, unsigned long, addr, unsigned long, len, int, op)
+{
+ if (is_user_addr_valid(current, addr, len) != 0)
+ return -EINVAL;
+
+ if (op & DCACHE)
+ blackfin_dcache_flush_range(addr, addr + len);
+ if (op & ICACHE)
+ blackfin_icache_flush_range(addr, addr + len);
+
+ return 0;
+}
diff --git a/arch/blackfin/mach-bf518/boards/ezbrd.c b/arch/blackfin/mach-bf518/boards/ezbrd.c
index 44d6d52..f95e609 100644
--- a/arch/blackfin/mach-bf518/boards/ezbrd.c
+++ b/arch/blackfin/mach-bf518/boards/ezbrd.c
@@ -312,7 +312,7 @@
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
/* SPI (0) */
static struct bfin5xx_spi_master bfin_spi0_info = {
- .num_chipselect = 5,
+ .num_chipselect = 6,
.enable_dma = 1, /* master has the ability to do dma transfer */
.pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
};
@@ -347,7 +347,7 @@
/* SPI (1) */
static struct bfin5xx_spi_master bfin_spi1_info = {
- .num_chipselect = 5,
+ .num_chipselect = 6,
.enable_dma = 1, /* master has the ability to do dma transfer */
.pin_req = {P_SPI1_SCK, P_SPI1_MISO, P_SPI1_MOSI, 0},
};
@@ -525,6 +525,14 @@
#endif
#endif
+#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+static struct platform_device bfin_i2s = {
+ .name = "bfin-i2s",
+ .id = CONFIG_SND_BF5XX_SPORT_NUM,
+ /* TODO: add platform data here */
+};
+#endif
+
#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
static struct resource bfin_twi0_resource[] = {
[0] = {
@@ -559,6 +567,11 @@
.irq = IRQ_PF8,
},
#endif
+#if defined(CONFIG_SND_SOC_SSM2602) || defined(CONFIG_SND_SOC_SSM2602_MODULE)
+ {
+ I2C_BOARD_INFO("ssm2602", 0x1b),
+ },
+#endif
};
#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
@@ -736,6 +749,10 @@
&i2c_bfin_twi_device,
#endif
+#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+ &bfin_i2s,
+#endif
+
#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
&bfin_sport0_uart_device,
diff --git a/arch/blackfin/mach-bf518/boards/tcm-bf518.c b/arch/blackfin/mach-bf518/boards/tcm-bf518.c
index 9b72e5c..bead810 100644
--- a/arch/blackfin/mach-bf518/boards/tcm-bf518.c
+++ b/arch/blackfin/mach-bf518/boards/tcm-bf518.c
@@ -291,7 +291,7 @@
/* SPI (1) */
static struct bfin5xx_spi_master bfin_spi1_info = {
- .num_chipselect = 5,
+ .num_chipselect = 6,
.enable_dma = 1, /* master has the ability to do dma transfer */
.pin_req = {P_SPI1_SCK, P_SPI1_MISO, P_SPI1_MOSI, 0},
};
diff --git a/arch/blackfin/mach-bf518/include/mach/cdefBF51x_base.h b/arch/blackfin/mach-bf518/include/mach/cdefBF51x_base.h
index 29498e5..e16969f 100644
--- a/arch/blackfin/mach-bf518/include/mach/cdefBF51x_base.h
+++ b/arch/blackfin/mach-bf518/include/mach/cdefBF51x_base.h
@@ -262,14 +262,14 @@
#define bfin_write_SPORT0_TX(val) bfin_write32(SPORT0_TX, val)
#define bfin_read_SPORT0_RX() bfin_read32(SPORT0_RX)
#define bfin_write_SPORT0_RX(val) bfin_write32(SPORT0_RX, val)
-#define bfin_read_SPORT0_TX32() bfin_read32(SPORT0_TX32)
-#define bfin_write_SPORT0_TX32(val) bfin_write32(SPORT0_TX32, val)
-#define bfin_read_SPORT0_RX32() bfin_read32(SPORT0_RX32)
-#define bfin_write_SPORT0_RX32(val) bfin_write32(SPORT0_RX32, val)
-#define bfin_read_SPORT0_TX16() bfin_read16(SPORT0_TX16)
-#define bfin_write_SPORT0_TX16(val) bfin_write16(SPORT0_TX16, val)
-#define bfin_read_SPORT0_RX16() bfin_read16(SPORT0_RX16)
-#define bfin_write_SPORT0_RX16(val) bfin_write16(SPORT0_RX16, val)
+#define bfin_read_SPORT0_TX32() bfin_read32(SPORT0_TX)
+#define bfin_write_SPORT0_TX32(val) bfin_write32(SPORT0_TX, val)
+#define bfin_read_SPORT0_RX32() bfin_read32(SPORT0_RX)
+#define bfin_write_SPORT0_RX32(val) bfin_write32(SPORT0_RX, val)
+#define bfin_read_SPORT0_TX16() bfin_read16(SPORT0_TX)
+#define bfin_write_SPORT0_TX16(val) bfin_write16(SPORT0_TX, val)
+#define bfin_read_SPORT0_RX16() bfin_read16(SPORT0_RX)
+#define bfin_write_SPORT0_RX16(val) bfin_write16(SPORT0_RX, val)
#define bfin_read_SPORT0_RCR1() bfin_read16(SPORT0_RCR1)
#define bfin_write_SPORT0_RCR1(val) bfin_write16(SPORT0_RCR1, val)
#define bfin_read_SPORT0_RCR2() bfin_read16(SPORT0_RCR2)
@@ -317,14 +317,14 @@
#define bfin_write_SPORT1_TX(val) bfin_write32(SPORT1_TX, val)
#define bfin_read_SPORT1_RX() bfin_read32(SPORT1_RX)
#define bfin_write_SPORT1_RX(val) bfin_write32(SPORT1_RX, val)
-#define bfin_read_SPORT1_TX32() bfin_read32(SPORT1_TX32)
-#define bfin_write_SPORT1_TX32(val) bfin_write32(SPORT1_TX32, val)
-#define bfin_read_SPORT1_RX32() bfin_read32(SPORT1_RX32)
-#define bfin_write_SPORT1_RX32(val) bfin_write32(SPORT1_RX32, val)
-#define bfin_read_SPORT1_TX16() bfin_read16(SPORT1_TX16)
-#define bfin_write_SPORT1_TX16(val) bfin_write16(SPORT1_TX16, val)
-#define bfin_read_SPORT1_RX16() bfin_read16(SPORT1_RX16)
-#define bfin_write_SPORT1_RX16(val) bfin_write16(SPORT1_RX16, val)
+#define bfin_read_SPORT1_TX32() bfin_read32(SPORT1_TX)
+#define bfin_write_SPORT1_TX32(val) bfin_write32(SPORT1_TX, val)
+#define bfin_read_SPORT1_RX32() bfin_read32(SPORT1_RX)
+#define bfin_write_SPORT1_RX32(val) bfin_write32(SPORT1_RX, val)
+#define bfin_read_SPORT1_TX16() bfin_read16(SPORT1_TX)
+#define bfin_write_SPORT1_TX16(val) bfin_write16(SPORT1_TX, val)
+#define bfin_read_SPORT1_RX16() bfin_read16(SPORT1_RX)
+#define bfin_write_SPORT1_RX16(val) bfin_write16(SPORT1_RX, val)
#define bfin_read_SPORT1_RCR1() bfin_read16(SPORT1_RCR1)
#define bfin_write_SPORT1_RCR1(val) bfin_write16(SPORT1_RCR1, val)
#define bfin_read_SPORT1_RCR2() bfin_read16(SPORT1_RCR2)
diff --git a/arch/blackfin/mach-bf518/include/mach/defBF51x_base.h b/arch/blackfin/mach-bf518/include/mach/defBF51x_base.h
index 037a51f..5f84913 100644
--- a/arch/blackfin/mach-bf518/include/mach/defBF51x_base.h
+++ b/arch/blackfin/mach-bf518/include/mach/defBF51x_base.h
@@ -748,51 +748,6 @@
#define FFE 0x20 /* Force Framing Error On Transmit */
-/* *********** SERIAL PERIPHERAL INTERFACE (SPI) MASKS ****************************/
-/* SPI_CTL Masks */
-#define TIMOD 0x0003 /* Transfer Initiate Mode */
-#define RDBR_CORE 0x0000 /* RDBR Read Initiates, IRQ When RDBR Full */
-#define TDBR_CORE 0x0001 /* TDBR Write Initiates, IRQ When TDBR Empty */
-#define RDBR_DMA 0x0002 /* DMA Read, DMA Until FIFO Empty */
-#define TDBR_DMA 0x0003 /* DMA Write, DMA Until FIFO Full */
-#define SZ 0x0004 /* Send Zero (When TDBR Empty, Send Zero/Last*) */
-#define GM 0x0008 /* Get More (When RDBR Full, Overwrite/Discard*) */
-#define PSSE 0x0010 /* Slave-Select Input Enable */
-#define EMISO 0x0020 /* Enable MISO As Output */
-#define SIZE 0x0100 /* Size of Words (16/8* Bits) */
-#define LSBF 0x0200 /* LSB First */
-#define CPHA 0x0400 /* Clock Phase */
-#define CPOL 0x0800 /* Clock Polarity */
-#define MSTR 0x1000 /* Master/Slave* */
-#define WOM 0x2000 /* Write Open Drain Master */
-#define SPE 0x4000 /* SPI Enable */
-
-/* SPI_FLG Masks */
-#define FLS1 0x0002 /* Enables SPI_FLOUT1 as SPI Slave-Select Output */
-#define FLS2 0x0004 /* Enables SPI_FLOUT2 as SPI Slave-Select Output */
-#define FLS3 0x0008 /* Enables SPI_FLOUT3 as SPI Slave-Select Output */
-#define FLS4 0x0010 /* Enables SPI_FLOUT4 as SPI Slave-Select Output */
-#define FLS5 0x0020 /* Enables SPI_FLOUT5 as SPI Slave-Select Output */
-#define FLS6 0x0040 /* Enables SPI_FLOUT6 as SPI Slave-Select Output */
-#define FLS7 0x0080 /* Enables SPI_FLOUT7 as SPI Slave-Select Output */
-#define FLG1 0xFDFF /* Activates SPI_FLOUT1 */
-#define FLG2 0xFBFF /* Activates SPI_FLOUT2 */
-#define FLG3 0xF7FF /* Activates SPI_FLOUT3 */
-#define FLG4 0xEFFF /* Activates SPI_FLOUT4 */
-#define FLG5 0xDFFF /* Activates SPI_FLOUT5 */
-#define FLG6 0xBFFF /* Activates SPI_FLOUT6 */
-#define FLG7 0x7FFF /* Activates SPI_FLOUT7 */
-
-/* SPI_STAT Masks */
-#define SPIF 0x0001 /* SPI Finished (Single-Word Transfer Complete) */
-#define MODF 0x0002 /* Mode Fault Error (Another Device Tried To Become Master) */
-#define TXE 0x0004 /* Transmission Error (Data Sent With No New Data In TDBR) */
-#define TXS 0x0008 /* SPI_TDBR Data Buffer Status (Full/Empty*) */
-#define RBSY 0x0010 /* Receive Error (Data Received With RDBR Full) */
-#define RXS 0x0020 /* SPI_RDBR Data Buffer Status (Full/Empty*) */
-#define TXCOL 0x0040 /* Transmit Collision Error (Corrupt Data May Have Been Sent) */
-
-
/* **************** GENERAL PURPOSE TIMER MASKS **********************/
/* TIMER_ENABLE Masks */
#define TIMEN0 0x0001 /* Enable Timer 0 */
diff --git a/arch/blackfin/mach-bf527/boards/Kconfig b/arch/blackfin/mach-bf527/boards/Kconfig
index b14c288..1cc2667 100644
--- a/arch/blackfin/mach-bf527/boards/Kconfig
+++ b/arch/blackfin/mach-bf527/boards/Kconfig
@@ -24,4 +24,14 @@
help
BF526-EZBRD/EZKIT Lite board support.
+config BFIN527_AD7160EVAL
+ bool "BF527-AD7160-EVAL"
+ help
+ BF527-AD7160-EVAL board support.
+
+config BFIN527_TLL6527M
+ bool "The Learning Labs TLL6527M"
+ help
+ TLL6527M V1.0 platform support
+
endchoice
diff --git a/arch/blackfin/mach-bf527/boards/Makefile b/arch/blackfin/mach-bf527/boards/Makefile
index 51a5817..1d67da9 100644
--- a/arch/blackfin/mach-bf527/boards/Makefile
+++ b/arch/blackfin/mach-bf527/boards/Makefile
@@ -6,3 +6,5 @@
obj-$(CONFIG_BFIN527_EZKIT_V2) += ezkit.o
obj-$(CONFIG_BFIN527_BLUETECHNIX_CM) += cm_bf527.o
obj-$(CONFIG_BFIN526_EZBRD) += ezbrd.o
+obj-$(CONFIG_BFIN527_AD7160EVAL) += ad7160eval.o
+obj-$(CONFIG_BFIN527_TLL6527M) += tll6527m.o
diff --git a/arch/blackfin/mach-bf527/boards/ad7160eval.c b/arch/blackfin/mach-bf527/boards/ad7160eval.c
new file mode 100644
index 0000000..fc767ac
--- /dev/null
+++ b/arch/blackfin/mach-bf527/boards/ad7160eval.c
@@ -0,0 +1,870 @@
+/*
+ * Copyright 2004-20010 Analog Devices Inc.
+ * 2005 National ICT Australia (NICTA)
+ * Aidan Williams <aidan@nicta.com.au>
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+#include <linux/i2c.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <linux/usb/musb.h>
+#include <linux/leds.h>
+#include <linux/input.h>
+#include <asm/dma.h>
+#include <asm/bfin5xx_spi.h>
+#include <asm/reboot.h>
+#include <asm/nand.h>
+#include <asm/portmux.h>
+#include <asm/dpmc.h>
+
+
+/*
+ * Name the Board for the /proc/cpuinfo
+ */
+const char bfin_board_name[] = "ADI BF527-AD7160EVAL";
+
+/*
+ * Driver needs to know address, irq and flag pin.
+ */
+
+#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+static struct resource musb_resources[] = {
+ [0] = {
+ .start = 0xffc03800,
+ .end = 0xffc03cff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = { /* general IRQ */
+ .start = IRQ_USB_INT0,
+ .end = IRQ_USB_INT0,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+ },
+ [2] = { /* DMA IRQ */
+ .start = IRQ_USB_DMA,
+ .end = IRQ_USB_DMA,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+ },
+};
+
+static struct musb_hdrc_config musb_config = {
+ .multipoint = 0,
+ .dyn_fifo = 0,
+ .soft_con = 1,
+ .dma = 1,
+ .num_eps = 8,
+ .dma_channels = 8,
+ .gpio_vrsel = GPIO_PG13,
+ /* Some custom boards need to be active low, just set it to "0"
+ * if it is the case.
+ */
+ .gpio_vrsel_active = 1,
+};
+
+static struct musb_hdrc_platform_data musb_plat = {
+#if defined(CONFIG_USB_MUSB_OTG)
+ .mode = MUSB_OTG,
+#elif defined(CONFIG_USB_MUSB_HDRC_HCD)
+ .mode = MUSB_HOST,
+#elif defined(CONFIG_USB_GADGET_MUSB_HDRC)
+ .mode = MUSB_PERIPHERAL,
+#endif
+ .config = &musb_config,
+};
+
+static u64 musb_dmamask = ~(u32)0;
+
+static struct platform_device musb_device = {
+ .name = "musb_hdrc",
+ .id = 0,
+ .dev = {
+ .dma_mask = &musb_dmamask,
+ .coherent_dma_mask = 0xffffffff,
+ .platform_data = &musb_plat,
+ },
+ .num_resources = ARRAY_SIZE(musb_resources),
+ .resource = musb_resources,
+};
+#endif
+
+#if defined(CONFIG_FB_BFIN_RA158Z) || defined(CONFIG_FB_BFIN_RA158Z_MODULE)
+static struct resource bf52x_ra158z_resources[] = {
+ {
+ .start = IRQ_PPI_ERROR,
+ .end = IRQ_PPI_ERROR,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bf52x_ra158z_device = {
+ .name = "bfin-ra158z",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(bf52x_ra158z_resources),
+ .resource = bf52x_ra158z_resources,
+};
+#endif
+
+#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+static struct mtd_partition ad7160eval_partitions[] = {
+ {
+ .name = "bootloader(nor)",
+ .size = 0x40000,
+ .offset = 0,
+ }, {
+ .name = "linux kernel(nor)",
+ .size = 0x1C0000,
+ .offset = MTDPART_OFS_APPEND,
+ }, {
+ .name = "file system(nor)",
+ .size = MTDPART_SIZ_FULL,
+ .offset = MTDPART_OFS_APPEND,
+ }
+};
+
+static struct physmap_flash_data ad7160eval_flash_data = {
+ .width = 2,
+ .parts = ad7160eval_partitions,
+ .nr_parts = ARRAY_SIZE(ad7160eval_partitions),
+};
+
+static struct resource ad7160eval_flash_resource = {
+ .start = 0x20000000,
+ .end = 0x203fffff,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device ad7160eval_flash_device = {
+ .name = "physmap-flash",
+ .id = 0,
+ .dev = {
+ .platform_data = &ad7160eval_flash_data,
+ },
+ .num_resources = 1,
+ .resource = &ad7160eval_flash_resource,
+};
+#endif
+
+#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+static struct mtd_partition partition_info[] = {
+ {
+ .name = "linux kernel(nand)",
+ .offset = 0,
+ .size = 4 * 1024 * 1024,
+ },
+ {
+ .name = "file system(nand)",
+ .offset = MTDPART_OFS_APPEND,
+ .size = MTDPART_SIZ_FULL,
+ },
+};
+
+static struct bf5xx_nand_platform bf5xx_nand_platform = {
+ .data_width = NFC_NWIDTH_8,
+ .partitions = partition_info,
+ .nr_partitions = ARRAY_SIZE(partition_info),
+ .rd_dly = 3,
+ .wr_dly = 3,
+};
+
+static struct resource bf5xx_nand_resources[] = {
+ {
+ .start = NFC_CTL,
+ .end = NFC_DATA_RD + 2,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = CH_NFC,
+ .end = CH_NFC,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bf5xx_nand_device = {
+ .name = "bf5xx-nand",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bf5xx_nand_resources),
+ .resource = bf5xx_nand_resources,
+ .dev = {
+ .platform_data = &bf5xx_nand_platform,
+ },
+};
+#endif
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+static struct platform_device rtc_device = {
+ .name = "rtc-bfin",
+ .id = -1,
+};
+#endif
+
+#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#include <linux/bfin_mac.h>
+static const unsigned short bfin_mac_peripherals[] = P_RMII0;
+
+static struct bfin_phydev_platform_data bfin_phydev_data[] = {
+ {
+ .addr = 1,
+ .irq = IRQ_MAC_PHYINT,
+ },
+};
+
+static struct bfin_mii_bus_platform_data bfin_mii_bus_data = {
+ .phydev_number = 1,
+ .phydev_data = bfin_phydev_data,
+ .phy_mode = PHY_INTERFACE_MODE_RMII,
+ .mac_peripherals = bfin_mac_peripherals,
+};
+
+static struct platform_device bfin_mii_bus = {
+ .name = "bfin_mii_bus",
+ .dev = {
+ .platform_data = &bfin_mii_bus_data,
+ }
+};
+
+static struct platform_device bfin_mac_device = {
+ .name = "bfin_mac",
+ .dev = {
+ .platform_data = &bfin_mii_bus,
+ }
+};
+#endif
+
+
+#if defined(CONFIG_MTD_M25P80) \
+ || defined(CONFIG_MTD_M25P80_MODULE)
+static struct mtd_partition bfin_spi_flash_partitions[] = {
+ {
+ .name = "bootloader(spi)",
+ .size = 0x00040000,
+ .offset = 0,
+ .mask_flags = MTD_CAP_ROM
+ }, {
+ .name = "linux kernel(spi)",
+ .size = MTDPART_SIZ_FULL,
+ .offset = MTDPART_OFS_APPEND,
+ }
+};
+
+static struct flash_platform_data bfin_spi_flash_data = {
+ .name = "m25p80",
+ .parts = bfin_spi_flash_partitions,
+ .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
+ .type = "m25p16",
+};
+
+/* SPI flash chip (m25p64) */
+static struct bfin5xx_spi_chip spi_flash_chip_info = {
+ .enable_dma = 0, /* use dma transfer with this chip*/
+ .bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
+ || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+static struct bfin5xx_spi_chip mmc_spi_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+static struct bfin5xx_spi_chip spidev_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+static struct platform_device bfin_i2s = {
+ .name = "bfin-i2s",
+ .id = CONFIG_SND_BF5XX_SPORT_NUM,
+ /* TODO: add platform data here */
+};
+#endif
+
+#if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
+static struct platform_device bfin_tdm = {
+ .name = "bfin-tdm",
+ .id = CONFIG_SND_BF5XX_SPORT_NUM,
+ /* TODO: add platform data here */
+};
+#endif
+
+static struct spi_board_info bfin_spi_board_info[] __initdata = {
+#if defined(CONFIG_MTD_M25P80) \
+ || defined(CONFIG_MTD_M25P80_MODULE)
+ {
+ /* the modalias must be the same as spi device driver name */
+ .modalias = "m25p80", /* Name of spi_driver for this device */
+ .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0, /* Framework bus number */
+ .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
+ .platform_data = &bfin_spi_flash_data,
+ .controller_data = &spi_flash_chip_info,
+ .mode = SPI_MODE_3,
+ },
+#endif
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
+ || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+ {
+ .modalias = "ad183x",
+ .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 4,
+ .controller_data = &ad1836_spi_chip_info,
+ },
+#endif
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+ {
+ .modalias = "mmc_spi",
+ .max_speed_hz = 30000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = GPIO_PH3 + MAX_CTRL_CS,
+ .controller_data = &mmc_spi_chip_info,
+ .mode = SPI_MODE_3,
+ },
+#endif
+#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+ {
+ .modalias = "spidev",
+ .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 1,
+ .controller_data = &spidev_chip_info,
+ },
+#endif
+};
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+/* SPI controller data */
+static struct bfin5xx_spi_master bfin_spi0_info = {
+ .num_chipselect = MAX_CTRL_CS + MAX_BLACKFIN_GPIOS,
+ .enable_dma = 1, /* master has the ability to do dma transfer */
+ .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
+};
+
+/* SPI (0) */
+static struct resource bfin_spi0_resource[] = {
+ [0] = {
+ .start = SPI0_REGBASE,
+ .end = SPI0_REGBASE + 0xFF,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = CH_SPI,
+ .end = CH_SPI,
+ .flags = IORESOURCE_DMA,
+ },
+ [2] = {
+ .start = IRQ_SPI,
+ .end = IRQ_SPI,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bfin_spi0_device = {
+ .name = "bfin-spi",
+ .id = 0, /* Bus number */
+ .num_resources = ARRAY_SIZE(bfin_spi0_resource),
+ .resource = bfin_spi0_resource,
+ .dev = {
+ .platform_data = &bfin_spi0_info, /* Passed to driver */
+ },
+};
+#endif /* spi master and devices */
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#ifdef CONFIG_SERIAL_BFIN_UART0
+static struct resource bfin_uart0_resources[] = {
+ {
+ .start = UART0_THR,
+ .end = UART0_GCTL+2,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_UART0_RX,
+ .end = IRQ_UART0_RX+1,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = IRQ_UART0_ERROR,
+ .end = IRQ_UART0_ERROR,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = CH_UART0_TX,
+ .end = CH_UART0_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ {
+ .start = CH_UART0_RX,
+ .end = CH_UART0_RX,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+unsigned short bfin_uart0_peripherals[] = {
+ P_UART0_TX, P_UART0_RX, 0
+};
+
+static struct platform_device bfin_uart0_device = {
+ .name = "bfin-uart",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bfin_uart0_resources),
+ .resource = bfin_uart0_resources,
+ .dev = {
+ .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
+ },
+};
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+static struct resource bfin_uart1_resources[] = {
+ {
+ .start = UART1_THR,
+ .end = UART1_GCTL+2,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_UART1_RX,
+ .end = IRQ_UART1_RX+1,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = IRQ_UART1_ERROR,
+ .end = IRQ_UART1_ERROR,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = CH_UART1_TX,
+ .end = CH_UART1_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ {
+ .start = CH_UART1_RX,
+ .end = CH_UART1_RX,
+ .flags = IORESOURCE_DMA,
+ },
+#ifdef CONFIG_BFIN_UART1_CTSRTS
+ { /* CTS pin */
+ .start = GPIO_PF9,
+ .end = GPIO_PF9,
+ .flags = IORESOURCE_IO,
+ },
+ { /* RTS pin */
+ .start = GPIO_PF10,
+ .end = GPIO_PF10,
+ .flags = IORESOURCE_IO,
+ },
+#endif
+};
+
+unsigned short bfin_uart1_peripherals[] = {
+ P_UART1_TX, P_UART1_RX, 0
+};
+
+static struct platform_device bfin_uart1_device = {
+ .name = "bfin-uart",
+ .id = 1,
+ .num_resources = ARRAY_SIZE(bfin_uart1_resources),
+ .resource = bfin_uart1_resources,
+ .dev = {
+ .platform_data = &bfin_uart1_peripherals, /* Passed to driver */
+ },
+};
+#endif
+#endif
+
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#ifdef CONFIG_BFIN_SIR0
+static struct resource bfin_sir0_resources[] = {
+ {
+ .start = 0xFFC00400,
+ .end = 0xFFC004FF,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_UART0_RX,
+ .end = IRQ_UART0_RX+1,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = CH_UART0_RX,
+ .end = CH_UART0_RX+1,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device bfin_sir0_device = {
+ .name = "bfin_sir",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bfin_sir0_resources),
+ .resource = bfin_sir0_resources,
+};
+#endif
+#ifdef CONFIG_BFIN_SIR1
+static struct resource bfin_sir1_resources[] = {
+ {
+ .start = 0xFFC02000,
+ .end = 0xFFC020FF,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_UART1_RX,
+ .end = IRQ_UART1_RX+1,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = CH_UART1_RX,
+ .end = CH_UART1_RX+1,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device bfin_sir1_device = {
+ .name = "bfin_sir",
+ .id = 1,
+ .num_resources = ARRAY_SIZE(bfin_sir1_resources),
+ .resource = bfin_sir1_resources,
+};
+#endif
+#endif
+
+#if defined(CONFIG_TOUCHSCREEN_AD7160) || defined(CONFIG_TOUCHSCREEN_AD7160_MODULE)
+#include <linux/input/ad7160.h>
+static const struct ad7160_platform_data bfin_ad7160_ts_info = {
+ .sensor_x_res = 854,
+ .sensor_y_res = 480,
+ .pressure = 100,
+ .filter_coef = 3,
+ .coord_pref = AD7160_ORIG_TOP_LEFT,
+ .first_touch_window = 5,
+ .move_window = 3,
+ .event_cabs = AD7160_EMIT_ABS_MT_TRACKING_ID |
+ AD7160_EMIT_ABS_MT_PRESSURE |
+ AD7160_TRACKING_ID_ASCENDING,
+ .finger_act_ctrl = 0x64,
+ .haptic_effect1_ctrl = AD7160_HAPTIC_SLOT_A(60) |
+ AD7160_HAPTIC_SLOT_A_LVL_HIGH |
+ AD7160_HAPTIC_SLOT_B(60) |
+ AD7160_HAPTIC_SLOT_B_LVL_LOW,
+
+ .haptic_effect2_ctrl = AD7160_HAPTIC_SLOT_A(20) |
+ AD7160_HAPTIC_SLOT_A_LVL_HIGH |
+ AD7160_HAPTIC_SLOT_B(80) |
+ AD7160_HAPTIC_SLOT_B_LVL_LOW |
+ AD7160_HAPTIC_SLOT_C(120) |
+ AD7160_HAPTIC_SLOT_C_LVL_HIGH |
+ AD7160_HAPTIC_SLOT_D(30) |
+ AD7160_HAPTIC_SLOT_D_LVL_LOW,
+};
+#endif
+
+#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+static struct resource bfin_twi0_resource[] = {
+ [0] = {
+ .start = TWI0_REGBASE,
+ .end = TWI0_REGBASE,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = IRQ_TWI,
+ .end = IRQ_TWI,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device i2c_bfin_twi_device = {
+ .name = "i2c-bfin-twi",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bfin_twi0_resource),
+ .resource = bfin_twi0_resource,
+};
+#endif
+
+static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
+#if defined(CONFIG_TOUCHSCREEN_AD7160) || defined(CONFIG_TOUCHSCREEN_AD7160_MODULE)
+ {
+ I2C_BOARD_INFO("ad7160", 0x33),
+ .irq = IRQ_PH1,
+ .platform_data = (void *)&bfin_ad7160_ts_info,
+ },
+#endif
+};
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
+static struct resource bfin_sport0_uart_resources[] = {
+ {
+ .start = SPORT0_TCR1,
+ .end = SPORT0_MRCS3+4,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_SPORT0_RX,
+ .end = IRQ_SPORT0_RX+1,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = IRQ_SPORT0_ERROR,
+ .end = IRQ_SPORT0_ERROR,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+unsigned short bfin_sport0_peripherals[] = {
+ P_SPORT0_TFS, P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS,
+ P_SPORT0_DRPRI, P_SPORT0_RSCLK, P_SPORT0_DRSEC, P_SPORT0_DTSEC, 0
+};
+
+static struct platform_device bfin_sport0_uart_device = {
+ .name = "bfin-sport-uart",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bfin_sport0_uart_resources),
+ .resource = bfin_sport0_uart_resources,
+ .dev = {
+ .platform_data = &bfin_sport0_peripherals, /* Passed to driver */
+ },
+};
+#endif
+#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
+static struct resource bfin_sport1_uart_resources[] = {
+ {
+ .start = SPORT1_TCR1,
+ .end = SPORT1_MRCS3+4,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_SPORT1_RX,
+ .end = IRQ_SPORT1_RX+1,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = IRQ_SPORT1_ERROR,
+ .end = IRQ_SPORT1_ERROR,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+unsigned short bfin_sport1_peripherals[] = {
+ P_SPORT1_TFS, P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_RFS,
+ P_SPORT1_DRPRI, P_SPORT1_RSCLK, P_SPORT1_DRSEC, P_SPORT1_DTSEC, 0
+};
+
+static struct platform_device bfin_sport1_uart_device = {
+ .name = "bfin-sport-uart",
+ .id = 1,
+ .num_resources = ARRAY_SIZE(bfin_sport1_uart_resources),
+ .resource = bfin_sport1_uart_resources,
+ .dev = {
+ .platform_data = &bfin_sport1_peripherals, /* Passed to driver */
+ },
+};
+#endif
+#endif
+
+#if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
+#include <asm/bfin_rotary.h>
+
+static struct bfin_rotary_platform_data bfin_rotary_data = {
+ /*.rotary_up_key = KEY_UP,*/
+ /*.rotary_down_key = KEY_DOWN,*/
+ .rotary_rel_code = REL_WHEEL,
+ .rotary_button_key = KEY_ENTER,
+ .debounce = 10, /* 0..17 */
+ .mode = ROT_QUAD_ENC | ROT_DEBE,
+};
+
+static struct resource bfin_rotary_resources[] = {
+ {
+ .start = IRQ_CNT,
+ .end = IRQ_CNT,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bfin_rotary_device = {
+ .name = "bfin-rotary",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(bfin_rotary_resources),
+ .resource = bfin_rotary_resources,
+ .dev = {
+ .platform_data = &bfin_rotary_data,
+ },
+};
+#endif
+
+static const unsigned int cclk_vlev_datasheet[] = {
+ VRPAIR(VLEV_100, 400000000),
+ VRPAIR(VLEV_105, 426000000),
+ VRPAIR(VLEV_110, 500000000),
+ VRPAIR(VLEV_115, 533000000),
+ VRPAIR(VLEV_120, 600000000),
+};
+
+static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
+ .tuple_tab = cclk_vlev_datasheet,
+ .tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
+ .vr_settling_time = 25 /* us */,
+};
+
+static struct platform_device bfin_dpmc = {
+ .name = "bfin dpmc",
+ .dev = {
+ .platform_data = &bfin_dmpc_vreg_data,
+ },
+};
+
+static struct platform_device *stamp_devices[] __initdata = {
+
+ &bfin_dpmc,
+
+#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+ &bf5xx_nand_device,
+#endif
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+ &rtc_device,
+#endif
+
+#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+ &musb_device,
+#endif
+
+#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+ &bfin_mii_bus,
+ &bfin_mac_device,
+#endif
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+ &bfin_spi0_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#ifdef CONFIG_SERIAL_BFIN_UART0
+ &bfin_uart0_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+ &bfin_uart1_device,
+#endif
+#endif
+
+#if defined(CONFIG_FB_BFIN_RA158Z) || defined(CONFIG_FB_BFIN_RA158Z_MODULE)
+ &bf52x_ra158z_device,
+#endif
+
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#ifdef CONFIG_BFIN_SIR0
+ &bfin_sir0_device,
+#endif
+#ifdef CONFIG_BFIN_SIR1
+ &bfin_sir1_device,
+#endif
+#endif
+
+#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+ &i2c_bfin_twi_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
+ &bfin_sport0_uart_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
+ &bfin_sport1_uart_device,
+#endif
+#endif
+
+#if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
+ &bfin_rotary_device,
+#endif
+
+#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+ &ad7160eval_flash_device,
+#endif
+
+#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+ &bfin_i2s,
+#endif
+
+#if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
+ &bfin_tdm,
+#endif
+};
+
+static int __init ad7160eval_init(void)
+{
+ printk(KERN_INFO "%s(): registering device resources\n", __func__);
+ i2c_register_board_info(0, bfin_i2c_board_info,
+ ARRAY_SIZE(bfin_i2c_board_info));
+ platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices));
+ spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
+ return 0;
+}
+
+arch_initcall(ad7160eval_init);
+
+static struct platform_device *ad7160eval_early_devices[] __initdata = {
+#if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
+#ifdef CONFIG_SERIAL_BFIN_UART0
+ &bfin_uart0_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+ &bfin_uart1_device,
+#endif
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT_CONSOLE)
+#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
+ &bfin_sport0_uart_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
+ &bfin_sport1_uart_device,
+#endif
+#endif
+};
+
+void __init native_machine_early_platform_add_devices(void)
+{
+ printk(KERN_INFO "register early platform devices\n");
+ early_platform_add_devices(ad7160eval_early_devices,
+ ARRAY_SIZE(ad7160eval_early_devices));
+}
+
+void native_machine_restart(char *cmd)
+{
+ /* workaround reboot hang when booting from SPI */
+ if ((bfin_read_SYSCR() & 0x7) == 0x3)
+ bfin_reset_boot_spi_cs(P_DEFAULT_BOOT_SPI_CS);
+}
+
+void bfin_get_ether_addr(char *addr)
+{
+ /* the MAC is stored in OTP memory page 0xDF */
+ u32 ret;
+ u64 otp_mac;
+ u32 (*otp_read)(u32 page, u32 flags, u64 *page_content) = (void *)0xEF00001A;
+
+ ret = otp_read(0xDF, 0x00, &otp_mac);
+ if (!(ret & 0x1)) {
+ char *otp_mac_p = (char *)&otp_mac;
+ for (ret = 0; ret < 6; ++ret)
+ addr[ret] = otp_mac_p[5 - ret];
+ }
+}
+EXPORT_SYMBOL(bfin_get_ether_addr);
diff --git a/arch/blackfin/mach-bf527/boards/cm_bf527.c b/arch/blackfin/mach-bf527/boards/cm_bf527.c
index 645ba5c..38037c7 100644
--- a/arch/blackfin/mach-bf527/boards/cm_bf527.c
+++ b/arch/blackfin/mach-bf527/boards/cm_bf527.c
@@ -342,8 +342,8 @@
};
#endif
-#if defined(CONFIG_SND_BLACKFIN_AD183X) \
- || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
+ || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
@@ -420,13 +420,13 @@
},
#endif
-#if defined(CONFIG_SND_BLACKFIN_AD183X) \
- || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
+ || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
{
- .modalias = "ad1836",
+ .modalias = "ad183x",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
- .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+ .chip_select = 4,
.controller_data = &ad1836_spi_chip_info,
},
#endif
diff --git a/arch/blackfin/mach-bf527/boards/ezbrd.c b/arch/blackfin/mach-bf527/boards/ezbrd.c
index c975fe8..6cc64a1 100644
--- a/arch/blackfin/mach-bf527/boards/ezbrd.c
+++ b/arch/blackfin/mach-bf527/boards/ezbrd.c
@@ -137,8 +137,12 @@
#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
static struct mtd_partition partition_info[] = {
{
- .name = "linux kernel(nand)",
+ .name = "bootloader(nand)",
.offset = 0,
+ .size = 0x40000,
+ }, {
+ .name = "linux kernel(nand)",
+ .offset = MTDPART_OFS_APPEND,
.size = 4 * 1024 * 1024,
},
{
diff --git a/arch/blackfin/mach-bf527/boards/ezkit.c b/arch/blackfin/mach-bf527/boards/ezkit.c
index 87b41e9..07c132d 100644
--- a/arch/blackfin/mach-bf527/boards/ezkit.c
+++ b/arch/blackfin/mach-bf527/boards/ezkit.c
@@ -222,8 +222,12 @@
#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
static struct mtd_partition partition_info[] = {
{
- .name = "linux kernel(nand)",
+ .name = "bootloader(nand)",
.offset = 0,
+ .size = 0x40000,
+ }, {
+ .name = "linux kernel(nand)",
+ .offset = MTDPART_OFS_APPEND,
.size = 4 * 1024 * 1024,
},
{
@@ -431,8 +435,8 @@
};
#endif
-#if defined(CONFIG_SND_BLACKFIN_AD183X) \
- || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
+ || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
@@ -547,13 +551,13 @@
},
#endif
-#if defined(CONFIG_SND_BLACKFIN_AD183X) \
- || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
+ || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
{
- .modalias = "ad1836",
+ .modalias = "ad183x",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
- .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+ .chip_select = 4,
.controller_data = &ad1836_spi_chip_info,
},
#endif
@@ -929,6 +933,11 @@
I2C_BOARD_INFO("ssm2602", 0x1b),
},
#endif
+#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+ {
+ I2C_BOARD_INFO("ad5252", 0x2f),
+ },
+#endif
};
#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
diff --git a/arch/blackfin/mach-bf527/boards/tll6527m.c b/arch/blackfin/mach-bf527/boards/tll6527m.c
new file mode 100644
index 0000000..ae4130e
--- /dev/null
+++ b/arch/blackfin/mach-bf527/boards/tll6527m.c
@@ -0,0 +1,986 @@
+/* File: arch/blackfin/mach-bf527/boards/tll6527m.c
+ * Based on: arch/blackfin/mach-bf527/boards/ezkit.c
+ * Author: Ashish Gupta
+ *
+ * Copyright: 2010 - The Learning Labs Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+#include <linux/i2c.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <linux/usb/musb.h>
+#include <linux/leds.h>
+#include <linux/input.h>
+#include <asm/dma.h>
+#include <asm/bfin5xx_spi.h>
+#include <asm/reboot.h>
+#include <asm/nand.h>
+#include <asm/portmux.h>
+#include <asm/dpmc.h>
+
+#if defined(CONFIG_TOUCHSCREEN_AD7879) \
+ || defined(CONFIG_TOUCHSCREEN_AD7879_MODULE)
+#include <linux/spi/ad7879.h>
+#define LCD_BACKLIGHT_GPIO 0x40
+/* TLL6527M uses TLL7UIQ35 / ADI LCD EZ Extender. AD7879 AUX GPIO is used for
+ * LCD Backlight Enable
+ */
+#endif
+
+/*
+ * Name the Board for the /proc/cpuinfo
+ */
+const char bfin_board_name[] = "TLL6527M";
+/*
+ * Driver needs to know address, irq and flag pin.
+ */
+
+#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+static struct resource musb_resources[] = {
+ [0] = {
+ .start = 0xffc03800,
+ .end = 0xffc03cff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = { /* general IRQ */
+ .start = IRQ_USB_INT0,
+ .end = IRQ_USB_INT0,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+ },
+ [2] = { /* DMA IRQ */
+ .start = IRQ_USB_DMA,
+ .end = IRQ_USB_DMA,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+ },
+};
+
+static struct musb_hdrc_config musb_config = {
+ .multipoint = 0,
+ .dyn_fifo = 0,
+ .soft_con = 1,
+ .dma = 1,
+ .num_eps = 8,
+ .dma_channels = 8,
+ /*.gpio_vrsel = GPIO_PG13,*/
+ /* Some custom boards need to be active low, just set it to "0"
+ * if it is the case.
+ */
+ .gpio_vrsel_active = 1,
+};
+
+static struct musb_hdrc_platform_data musb_plat = {
+#if defined(CONFIG_USB_MUSB_OTG)
+ .mode = MUSB_OTG,
+#elif defined(CONFIG_USB_MUSB_HDRC_HCD)
+ .mode = MUSB_HOST,
+#elif defined(CONFIG_USB_GADGET_MUSB_HDRC)
+ .mode = MUSB_PERIPHERAL,
+#endif
+ .config = &musb_config,
+};
+
+static u64 musb_dmamask = ~(u32)0;
+
+static struct platform_device musb_device = {
+ .name = "musb_hdrc",
+ .id = 0,
+ .dev = {
+ .dma_mask = &musb_dmamask,
+ .coherent_dma_mask = 0xffffffff,
+ .platform_data = &musb_plat,
+ },
+ .num_resources = ARRAY_SIZE(musb_resources),
+ .resource = musb_resources,
+};
+#endif
+
+#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#include <asm/bfin-lq035q1.h>
+
+static struct bfin_lq035q1fb_disp_info bfin_lq035q1_data = {
+ .mode = LQ035_NORM | LQ035_RGB | LQ035_RL | LQ035_TB,
+ .ppi_mode = USE_RGB565_16_BIT_PPI,
+ .use_bl = 1,
+ .gpio_bl = LCD_BACKLIGHT_GPIO,
+};
+
+static struct resource bfin_lq035q1_resources[] = {
+ {
+ .start = IRQ_PPI_ERROR,
+ .end = IRQ_PPI_ERROR,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bfin_lq035q1_device = {
+ .name = "bfin-lq035q1",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(bfin_lq035q1_resources),
+ .resource = bfin_lq035q1_resources,
+ .dev = {
+ .platform_data = &bfin_lq035q1_data,
+ },
+};
+#endif
+
+#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+static struct mtd_partition tll6527m_partitions[] = {
+ {
+ .name = "bootloader(nor)",
+ .size = 0xA0000,
+ .offset = 0,
+ }, {
+ .name = "linux kernel(nor)",
+ .size = 0xD00000,
+ .offset = MTDPART_OFS_APPEND,
+ }, {
+ .name = "file system(nor)",
+ .size = MTDPART_SIZ_FULL,
+ .offset = MTDPART_OFS_APPEND,
+ }
+};
+
+static struct physmap_flash_data tll6527m_flash_data = {
+ .width = 2,
+ .parts = tll6527m_partitions,
+ .nr_parts = ARRAY_SIZE(tll6527m_partitions),
+};
+
+static unsigned tll6527m_flash_gpios[] = { GPIO_PG11, GPIO_PH11, GPIO_PH12 };
+
+static struct resource tll6527m_flash_resource[] = {
+ {
+ .name = "cfi_probe",
+ .start = 0x20000000,
+ .end = 0x201fffff,
+ .flags = IORESOURCE_MEM,
+ }, {
+ .start = (unsigned long)tll6527m_flash_gpios,
+ .end = ARRAY_SIZE(tll6527m_flash_gpios),
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+static struct platform_device tll6527m_flash_device = {
+ .name = "gpio-addr-flash",
+ .id = 0,
+ .dev = {
+ .platform_data = &tll6527m_flash_data,
+ },
+ .num_resources = ARRAY_SIZE(tll6527m_flash_resource),
+ .resource = tll6527m_flash_resource,
+};
+#endif
+
+#if defined(CONFIG_GPIO_DECODER) || defined(CONFIG_GPIO_DECODER_MODULE)
+/* An SN74LVC138A 3:8 decoder chip has been used to generate 7 augmented
+ * outputs used as SPI CS lines for all SPI SLAVE devices on TLL6527v1-0.
+ * EXP_GPIO_SPISEL_BASE is the base number for the expanded outputs being
+ * used as SPI CS lines, this should be > MAX_BLACKFIN_GPIOS
+ */
+#include <linux/gpio-decoder.h>
+#define EXP_GPIO_SPISEL_BASE 0x64
+static unsigned gpio_addr_inputs[] = {
+ GPIO_PG1, GPIO_PH9, GPIO_PH10
+};
+
+static struct gpio_decoder_platfrom_data spi_decoded_cs = {
+ .base = EXP_GPIO_SPISEL_BASE,
+ .input_addrs = gpio_addr_inputs,
+ .nr_input_addrs = ARRAY_SIZE(gpio_addr_inputs),
+ .default_output = 0,
+/* .default_output = (1 << ARRAY_SIZE(gpio_addr_inputs)) - 1 */
+};
+
+static struct platform_device spi_decoded_gpio = {
+ .name = "gpio-decoder",
+ .id = 0,
+ .dev = {
+ .platform_data = &spi_decoded_cs,
+ },
+};
+
+#else
+#define EXP_GPIO_SPISEL_BASE 0x0
+
+#endif
+
+#if defined(CONFIG_INPUT_ADXL34X) || defined(CONFIG_INPUT_ADXL34X_MODULE)
+#include <linux/input/adxl34x.h>
+static const struct adxl34x_platform_data adxl345_info = {
+ .x_axis_offset = 0,
+ .y_axis_offset = 0,
+ .z_axis_offset = 0,
+ .tap_threshold = 0x31,
+ .tap_duration = 0x10,
+ .tap_latency = 0x60,
+ .tap_window = 0xF0,
+ .tap_axis_control = ADXL_TAP_X_EN | ADXL_TAP_Y_EN | ADXL_TAP_Z_EN,
+ .act_axis_control = 0xFF,
+ .activity_threshold = 5,
+ .inactivity_threshold = 2,
+ .inactivity_time = 2,
+ .free_fall_threshold = 0x7,
+ .free_fall_time = 0x20,
+ .data_rate = 0x8,
+ .data_range = ADXL_FULL_RES,
+
+ .ev_type = EV_ABS,
+ .ev_code_x = ABS_X, /* EV_REL */
+ .ev_code_y = ABS_Y, /* EV_REL */
+ .ev_code_z = ABS_Z, /* EV_REL */
+
+ .ev_code_tap = {BTN_TOUCH, BTN_TOUCH, BTN_TOUCH}, /* EV_KEY x,y,z */
+
+/* .ev_code_ff = KEY_F,*/ /* EV_KEY */
+ .ev_code_act_inactivity = KEY_A, /* EV_KEY */
+ .use_int2 = 1,
+ .power_mode = ADXL_AUTO_SLEEP | ADXL_LINK,
+ .fifo_mode = ADXL_FIFO_STREAM,
+};
+#endif
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+static struct platform_device rtc_device = {
+ .name = "rtc-bfin",
+ .id = -1,
+};
+#endif
+
+#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+static struct platform_device bfin_mii_bus = {
+ .name = "bfin_mii_bus",
+};
+
+static struct platform_device bfin_mac_device = {
+ .name = "bfin_mac",
+ .dev.platform_data = &bfin_mii_bus,
+};
+#endif
+
+#if defined(CONFIG_MTD_M25P80) \
+ || defined(CONFIG_MTD_M25P80_MODULE)
+static struct mtd_partition bfin_spi_flash_partitions[] = {
+ {
+ .name = "bootloader(spi)",
+ .size = 0x00040000,
+ .offset = 0,
+ .mask_flags = MTD_CAP_ROM
+ }, {
+ .name = "linux kernel(spi)",
+ .size = MTDPART_SIZ_FULL,
+ .offset = MTDPART_OFS_APPEND,
+ }
+};
+
+static struct flash_platform_data bfin_spi_flash_data = {
+ .name = "m25p80",
+ .parts = bfin_spi_flash_partitions,
+ .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
+ .type = "m25p16",
+};
+
+/* SPI flash chip (m25p64) */
+static struct bfin5xx_spi_chip spi_flash_chip_info = {
+ .enable_dma = 0, /* use dma transfer with this chip*/
+ .bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_BFIN_SPI_ADC) \
+ || defined(CONFIG_BFIN_SPI_ADC_MODULE)
+/* SPI ADC chip */
+static struct bfin5xx_spi_chip spi_adc_chip_info = {
+ .enable_dma = 0, /* use dma transfer with this chip*/
+/*
+ * tll6527m V1.0 does not support native spi slave selects
+ * hence DMA mode will not be useful since the ADC needs
+ * CS to toggle for each sample and cs_change_per_word
+ * seems to be removed from spi_bfin5xx.c
+ */
+ .bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+static struct bfin5xx_spi_chip mmc_spi_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_TOUCHSCREEN_AD7879) \
+ || defined(CONFIG_TOUCHSCREEN_AD7879_MODULE)
+static const struct ad7879_platform_data bfin_ad7879_ts_info = {
+ .model = 7879, /* Model = AD7879 */
+ .x_plate_ohms = 620, /* 620 Ohm from the touch datasheet */
+ .pressure_max = 10000,
+ .pressure_min = 0,
+ .first_conversion_delay = 3,
+ /* wait 512us before do a first conversion */
+ .acquisition_time = 1, /* 4us acquisition time per sample */
+ .median = 2, /* do 8 measurements */
+ .averaging = 1,
+ /* take the average of 4 middle samples */
+ .pen_down_acc_interval = 255, /* 9.4 ms */
+ .gpio_export = 1, /* configure AUX as GPIO output*/
+ .gpio_base = LCD_BACKLIGHT_GPIO,
+};
+#endif
+
+#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) \
+ || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
+static struct bfin5xx_spi_chip spi_ad7879_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+static struct bfin5xx_spi_chip spidev_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+static struct platform_device bfin_i2s = {
+ .name = "bfin-i2s",
+ .id = CONFIG_SND_BF5XX_SPORT_NUM,
+ /* TODO: add platform data here */
+};
+#endif
+
+#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+static struct bfin5xx_spi_chip lq035q1_spi_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_GPIO_MCP23S08) || defined(CONFIG_GPIO_MCP23S08_MODULE)
+static struct bfin5xx_spi_chip spi_mcp23s08_sys_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 8,
+};
+
+static struct bfin5xx_spi_chip spi_mcp23s08_usr_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 8,
+};
+
+#include <linux/spi/mcp23s08.h>
+static const struct mcp23s08_platform_data bfin_mcp23s08_sys_gpio_info = {
+ .chip[0].is_present = true,
+ .base = 0x30,
+};
+static const struct mcp23s08_platform_data bfin_mcp23s08_usr_gpio_info = {
+ .chip[2].is_present = true,
+ .base = 0x38,
+};
+#endif
+
+static struct spi_board_info bfin_spi_board_info[] __initdata = {
+#if defined(CONFIG_MTD_M25P80) \
+ || defined(CONFIG_MTD_M25P80_MODULE)
+ {
+ /* the modalias must be the same as spi device driver name */
+ .modalias = "m25p80", /* Name of spi_driver for this device */
+ .max_speed_hz = 25000000,
+ /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0, /* Framework bus number */
+ .chip_select = EXP_GPIO_SPISEL_BASE + 0x04 + MAX_CTRL_CS,
+ /* Can be connected to TLL6527M GPIO connector */
+ /* Either SPI_ADC or M25P80 FLASH can be installed at a time */
+ .platform_data = &bfin_spi_flash_data,
+ .controller_data = &spi_flash_chip_info,
+ .mode = SPI_MODE_3,
+ },
+#endif
+
+#if defined(CONFIG_BFIN_SPI_ADC)
+ || defined(CONFIG_BFIN_SPI_ADC_MODULE)
+ {
+ .modalias = "bfin_spi_adc",
+ /* Name of spi_driver for this device */
+ .max_speed_hz = 10000000,
+ /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0, /* Framework bus number */
+ .chip_select = EXP_GPIO_SPISEL_BASE + 0x04 + MAX_CTRL_CS,
+ /* Framework chip select. */
+ .platform_data = NULL, /* No spi_driver specific config */
+ .controller_data = &spi_adc_chip_info,
+ .mode = SPI_MODE_0,
+ },
+#endif
+
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+ {
+ .modalias = "mmc_spi",
+/*
+ * TLL6527M V1.0 does not support SD Card at SPI Clock > 10 MHz due to
+ * SPI buffer limitations
+ */
+ .max_speed_hz = 10000000,
+ /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = EXP_GPIO_SPISEL_BASE + 0x05 + MAX_CTRL_CS,
+ .controller_data = &mmc_spi_chip_info,
+ .mode = SPI_MODE_0,
+ },
+#endif
+#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) \
+ || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
+ {
+ .modalias = "ad7879",
+ .platform_data = &bfin_ad7879_ts_info,
+ .irq = IRQ_PH14,
+ .max_speed_hz = 5000000,
+ /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = EXP_GPIO_SPISEL_BASE + 0x07 + MAX_CTRL_CS,
+ .controller_data = &spi_ad7879_chip_info,
+ .mode = SPI_CPHA | SPI_CPOL,
+ },
+#endif
+#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+ {
+ .modalias = "spidev",
+ .max_speed_hz = 10000000,
+ /* TLL6527Mv1-0 supports max spi clock (SCK) speed = 10 MHz */
+ .bus_num = 0,
+ .chip_select = EXP_GPIO_SPISEL_BASE + 0x03 + MAX_CTRL_CS,
+ .mode = SPI_CPHA | SPI_CPOL,
+ .controller_data = &spidev_chip_info,
+ },
+#endif
+#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+ {
+ .modalias = "bfin-lq035q1-spi",
+ .max_speed_hz = 20000000,
+ .bus_num = 0,
+ .chip_select = EXP_GPIO_SPISEL_BASE + 0x06 + MAX_CTRL_CS,
+ .controller_data = &lq035q1_spi_chip_info,
+ .mode = SPI_CPHA | SPI_CPOL,
+ },
+#endif
+#if defined(CONFIG_GPIO_MCP23S08) || defined(CONFIG_GPIO_MCP23S08_MODULE)
+ {
+ .modalias = "mcp23s08",
+ .platform_data = &bfin_mcp23s08_sys_gpio_info,
+ .max_speed_hz = 5000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = EXP_GPIO_SPISEL_BASE + 0x01 + MAX_CTRL_CS,
+ .controller_data = &spi_mcp23s08_sys_chip_info,
+ .mode = SPI_CPHA | SPI_CPOL,
+ },
+ {
+ .modalias = "mcp23s08",
+ .platform_data = &bfin_mcp23s08_usr_gpio_info,
+ .max_speed_hz = 5000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = EXP_GPIO_SPISEL_BASE + 0x02 + MAX_CTRL_CS,
+ .controller_data = &spi_mcp23s08_usr_chip_info,
+ .mode = SPI_CPHA | SPI_CPOL,
+ },
+#endif
+};
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+/* SPI controller data */
+static struct bfin5xx_spi_master bfin_spi0_info = {
+ .num_chipselect = EXP_GPIO_SPISEL_BASE + 8 + MAX_CTRL_CS,
+ /* EXP_GPIO_SPISEL_BASE will be > MAX_BLACKFIN_GPIOS */
+ .enable_dma = 1, /* master has the ability to do dma transfer */
+ .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
+};
+
+/* SPI (0) */
+static struct resource bfin_spi0_resource[] = {
+ [0] = {
+ .start = SPI0_REGBASE,
+ .end = SPI0_REGBASE + 0xFF,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = CH_SPI,
+ .end = CH_SPI,
+ .flags = IORESOURCE_DMA,
+ },
+ [2] = {
+ .start = IRQ_SPI,
+ .end = IRQ_SPI,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bfin_spi0_device = {
+ .name = "bfin-spi",
+ .id = 0, /* Bus number */
+ .num_resources = ARRAY_SIZE(bfin_spi0_resource),
+ .resource = bfin_spi0_resource,
+ .dev = {
+ .platform_data = &bfin_spi0_info, /* Passed to driver */
+ },
+};
+#endif /* spi master and devices */
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#ifdef CONFIG_SERIAL_BFIN_UART0
+static struct resource bfin_uart0_resources[] = {
+ {
+ .start = UART0_THR,
+ .end = UART0_GCTL+2,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_UART0_RX,
+ .end = IRQ_UART0_RX+1,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = IRQ_UART0_ERROR,
+ .end = IRQ_UART0_ERROR,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = CH_UART0_TX,
+ .end = CH_UART0_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ {
+ .start = CH_UART0_RX,
+ .end = CH_UART0_RX,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+unsigned short bfin_uart0_peripherals[] = {
+ P_UART0_TX, P_UART0_RX, 0
+};
+
+static struct platform_device bfin_uart0_device = {
+ .name = "bfin-uart",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bfin_uart0_resources),
+ .resource = bfin_uart0_resources,
+ .dev = {
+ .platform_data = &bfin_uart0_peripherals,
+ /* Passed to driver */
+ },
+};
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+static struct resource bfin_uart1_resources[] = {
+ {
+ .start = UART1_THR,
+ .end = UART1_GCTL+2,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_UART1_RX,
+ .end = IRQ_UART1_RX+1,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = IRQ_UART1_ERROR,
+ .end = IRQ_UART1_ERROR,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = CH_UART1_TX,
+ .end = CH_UART1_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ {
+ .start = CH_UART1_RX,
+ .end = CH_UART1_RX,
+ .flags = IORESOURCE_DMA,
+ },
+#ifdef CONFIG_BFIN_UART1_CTSRTS
+ { /* CTS pin */
+ .start = GPIO_PF9,
+ .end = GPIO_PF9,
+ .flags = IORESOURCE_IO,
+ },
+ { /* RTS pin */
+ .start = GPIO_PF10,
+ .end = GPIO_PF10,
+ .flags = IORESOURCE_IO,
+ },
+#endif
+};
+
+unsigned short bfin_uart1_peripherals[] = {
+ P_UART1_TX, P_UART1_RX, 0
+};
+
+static struct platform_device bfin_uart1_device = {
+ .name = "bfin-uart",
+ .id = 1,
+ .num_resources = ARRAY_SIZE(bfin_uart1_resources),
+ .resource = bfin_uart1_resources,
+ .dev = {
+ .platform_data = &bfin_uart1_peripherals,
+ /* Passed to driver */
+ },
+};
+#endif
+#endif
+
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#ifdef CONFIG_BFIN_SIR0
+static struct resource bfin_sir0_resources[] = {
+ {
+ .start = 0xFFC00400,
+ .end = 0xFFC004FF,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_UART0_RX,
+ .end = IRQ_UART0_RX+1,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = CH_UART0_RX,
+ .end = CH_UART0_RX+1,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device bfin_sir0_device = {
+ .name = "bfin_sir",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bfin_sir0_resources),
+ .resource = bfin_sir0_resources,
+};
+#endif
+#ifdef CONFIG_BFIN_SIR1
+static struct resource bfin_sir1_resources[] = {
+ {
+ .start = 0xFFC02000,
+ .end = 0xFFC020FF,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_UART1_RX,
+ .end = IRQ_UART1_RX+1,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = CH_UART1_RX,
+ .end = CH_UART1_RX+1,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device bfin_sir1_device = {
+ .name = "bfin_sir",
+ .id = 1,
+ .num_resources = ARRAY_SIZE(bfin_sir1_resources),
+ .resource = bfin_sir1_resources,
+};
+#endif
+#endif
+
+#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+static struct resource bfin_twi0_resource[] = {
+ [0] = {
+ .start = TWI0_REGBASE,
+ .end = TWI0_REGBASE,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = IRQ_TWI,
+ .end = IRQ_TWI,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device i2c_bfin_twi_device = {
+ .name = "i2c-bfin-twi",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bfin_twi0_resource),
+ .resource = bfin_twi0_resource,
+};
+#endif
+
+static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
+#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+ {
+ I2C_BOARD_INFO("pcf8574_lcd", 0x22),
+ },
+#endif
+
+#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
+ {
+ I2C_BOARD_INFO("bfin-adv7393", 0x2B),
+ },
+#endif
+#if defined(CONFIG_TOUCHSCREEN_AD7879_I2C) \
+ || defined(CONFIG_TOUCHSCREEN_AD7879_I2C_MODULE)
+ {
+ I2C_BOARD_INFO("ad7879", 0x2C),
+ .irq = IRQ_PH14,
+ .platform_data = (void *)&bfin_ad7879_ts_info,
+ },
+#endif
+#if defined(CONFIG_SND_SOC_SSM2602) || defined(CONFIG_SND_SOC_SSM2602_MODULE)
+ {
+ I2C_BOARD_INFO("ssm2602", 0x1b),
+ },
+#endif
+ {
+ I2C_BOARD_INFO("adm1192", 0x2e),
+ },
+
+ {
+ I2C_BOARD_INFO("ltc3576", 0x09),
+ },
+#if defined(CONFIG_INPUT_ADXL34X_I2C) \
+ || defined(CONFIG_INPUT_ADXL34X_I2C_MODULE)
+ {
+ I2C_BOARD_INFO("adxl34x", 0x53),
+ .irq = IRQ_PH13,
+ .platform_data = (void *)&adxl345_info,
+ },
+#endif
+};
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT) \
+ || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
+static struct resource bfin_sport0_uart_resources[] = {
+ {
+ .start = SPORT0_TCR1,
+ .end = SPORT0_MRCS3+4,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_SPORT0_RX,
+ .end = IRQ_SPORT0_RX+1,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = IRQ_SPORT0_ERROR,
+ .end = IRQ_SPORT0_ERROR,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+unsigned short bfin_sport0_peripherals[] = {
+ P_SPORT0_TFS, P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS,
+ P_SPORT0_DRPRI, P_SPORT0_RSCLK, P_SPORT0_DRSEC, P_SPORT0_DTSEC, 0
+};
+
+static struct platform_device bfin_sport0_uart_device = {
+ .name = "bfin-sport-uart",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bfin_sport0_uart_resources),
+ .resource = bfin_sport0_uart_resources,
+ .dev = {
+ .platform_data = &bfin_sport0_peripherals,
+ /* Passed to driver */
+ },
+};
+#endif
+#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
+static struct resource bfin_sport1_uart_resources[] = {
+ {
+ .start = SPORT1_TCR1,
+ .end = SPORT1_MRCS3+4,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_SPORT1_RX,
+ .end = IRQ_SPORT1_RX+1,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = IRQ_SPORT1_ERROR,
+ .end = IRQ_SPORT1_ERROR,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+unsigned short bfin_sport1_peripherals[] = {
+ P_SPORT1_TFS, P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_RFS,
+ P_SPORT1_DRPRI, P_SPORT1_RSCLK, P_SPORT1_DRSEC, P_SPORT1_DTSEC, 0
+};
+
+static struct platform_device bfin_sport1_uart_device = {
+ .name = "bfin-sport-uart",
+ .id = 1,
+ .num_resources = ARRAY_SIZE(bfin_sport1_uart_resources),
+ .resource = bfin_sport1_uart_resources,
+ .dev = {
+ .platform_data = &bfin_sport1_peripherals,
+ /* Passed to driver */
+ },
+};
+#endif
+#endif
+
+static const unsigned int cclk_vlev_datasheet[] = {
+ VRPAIR(VLEV_100, 400000000),
+ VRPAIR(VLEV_105, 426000000),
+ VRPAIR(VLEV_110, 500000000),
+ VRPAIR(VLEV_115, 533000000),
+ VRPAIR(VLEV_120, 600000000),
+};
+
+static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
+ .tuple_tab = cclk_vlev_datasheet,
+ .tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
+ .vr_settling_time = 25 /* us */,
+};
+
+static struct platform_device bfin_dpmc = {
+ .name = "bfin dpmc",
+ .dev = {
+ .platform_data = &bfin_dmpc_vreg_data,
+ },
+};
+
+static struct platform_device *tll6527m_devices[] __initdata = {
+
+ &bfin_dpmc,
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+ &rtc_device,
+#endif
+
+#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+ &musb_device,
+#endif
+
+#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+ &bfin_mii_bus,
+ &bfin_mac_device,
+#endif
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+ &bfin_spi0_device,
+#endif
+
+#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+ &bfin_lq035q1_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#ifdef CONFIG_SERIAL_BFIN_UART0
+ &bfin_uart0_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+ &bfin_uart1_device,
+#endif
+#endif
+
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#ifdef CONFIG_BFIN_SIR0
+ &bfin_sir0_device,
+#endif
+#ifdef CONFIG_BFIN_SIR1
+ &bfin_sir1_device,
+#endif
+#endif
+
+#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+ &i2c_bfin_twi_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT) \
+ || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
+ &bfin_sport0_uart_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
+ &bfin_sport1_uart_device,
+#endif
+#endif
+
+#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+ &tll6527m_flash_device,
+#endif
+
+#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+ &bfin_i2s,
+#endif
+
+#if defined(CONFIG_GPIO_DECODER) || defined(CONFIG_GPIO_DECODER_MODULE)
+ &spi_decoded_gpio,
+#endif
+};
+
+static int __init tll6527m_init(void)
+{
+ printk(KERN_INFO "%s(): registering device resources\n", __func__);
+ i2c_register_board_info(0, bfin_i2c_board_info,
+ ARRAY_SIZE(bfin_i2c_board_info));
+ platform_add_devices(tll6527m_devices, ARRAY_SIZE(tll6527m_devices));
+ spi_register_board_info(bfin_spi_board_info,
+ ARRAY_SIZE(bfin_spi_board_info));
+ return 0;
+}
+
+arch_initcall(tll6527m_init);
+
+static struct platform_device *tll6527m_early_devices[] __initdata = {
+#if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
+#ifdef CONFIG_SERIAL_BFIN_UART0
+ &bfin_uart0_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+ &bfin_uart1_device,
+#endif
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT_CONSOLE)
+#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
+ &bfin_sport0_uart_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
+ &bfin_sport1_uart_device,
+#endif
+#endif
+};
+
+void __init native_machine_early_platform_add_devices(void)
+{
+ printk(KERN_INFO "register early platform devices\n");
+ early_platform_add_devices(tll6527m_early_devices,
+ ARRAY_SIZE(tll6527m_early_devices));
+}
+
+void native_machine_restart(char *cmd)
+{
+ /* workaround reboot hang when booting from SPI */
+ if ((bfin_read_SYSCR() & 0x7) == 0x3)
+ bfin_reset_boot_spi_cs(P_DEFAULT_BOOT_SPI_CS);
+}
+
+void bfin_get_ether_addr(char *addr)
+{
+ /* the MAC is stored in OTP memory page 0xDF */
+ u32 ret;
+ u64 otp_mac;
+ u32 (*otp_read)(u32 page, u32 flags,
+ u64 *page_content) = (void *)0xEF00001A;
+
+ ret = otp_read(0xDF, 0x00, &otp_mac);
+ if (!(ret & 0x1)) {
+ char *otp_mac_p = (char *)&otp_mac;
+ for (ret = 0; ret < 6; ++ret)
+ addr[ret] = otp_mac_p[5 - ret];
+ }
+}
+EXPORT_SYMBOL(bfin_get_ether_addr);
diff --git a/arch/blackfin/mach-bf527/include/mach/cdefBF52x_base.h b/arch/blackfin/mach-bf527/include/mach/cdefBF52x_base.h
index 11fb27b..3048b52b 100644
--- a/arch/blackfin/mach-bf527/include/mach/cdefBF52x_base.h
+++ b/arch/blackfin/mach-bf527/include/mach/cdefBF52x_base.h
@@ -279,14 +279,14 @@
#define bfin_write_SPORT0_TX(val) bfin_write32(SPORT0_TX, val)
#define bfin_read_SPORT0_RX() bfin_read32(SPORT0_RX)
#define bfin_write_SPORT0_RX(val) bfin_write32(SPORT0_RX, val)
-#define bfin_read_SPORT0_TX32() bfin_read32(SPORT0_TX32)
-#define bfin_write_SPORT0_TX32(val) bfin_write32(SPORT0_TX32, val)
-#define bfin_read_SPORT0_RX32() bfin_read32(SPORT0_RX32)
-#define bfin_write_SPORT0_RX32(val) bfin_write32(SPORT0_RX32, val)
-#define bfin_read_SPORT0_TX16() bfin_read16(SPORT0_TX16)
-#define bfin_write_SPORT0_TX16(val) bfin_write16(SPORT0_TX16, val)
-#define bfin_read_SPORT0_RX16() bfin_read16(SPORT0_RX16)
-#define bfin_write_SPORT0_RX16(val) bfin_write16(SPORT0_RX16, val)
+#define bfin_read_SPORT0_TX32() bfin_read32(SPORT0_TX)
+#define bfin_write_SPORT0_TX32(val) bfin_write32(SPORT0_TX, val)
+#define bfin_read_SPORT0_RX32() bfin_read32(SPORT0_RX)
+#define bfin_write_SPORT0_RX32(val) bfin_write32(SPORT0_RX, val)
+#define bfin_read_SPORT0_TX16() bfin_read16(SPORT0_TX)
+#define bfin_write_SPORT0_TX16(val) bfin_write16(SPORT0_TX, val)
+#define bfin_read_SPORT0_RX16() bfin_read16(SPORT0_RX)
+#define bfin_write_SPORT0_RX16(val) bfin_write16(SPORT0_RX, val)
#define bfin_read_SPORT0_RCR1() bfin_read16(SPORT0_RCR1)
#define bfin_write_SPORT0_RCR1(val) bfin_write16(SPORT0_RCR1, val)
#define bfin_read_SPORT0_RCR2() bfin_read16(SPORT0_RCR2)
@@ -334,14 +334,14 @@
#define bfin_write_SPORT1_TX(val) bfin_write32(SPORT1_TX, val)
#define bfin_read_SPORT1_RX() bfin_read32(SPORT1_RX)
#define bfin_write_SPORT1_RX(val) bfin_write32(SPORT1_RX, val)
-#define bfin_read_SPORT1_TX32() bfin_read32(SPORT1_TX32)
-#define bfin_write_SPORT1_TX32(val) bfin_write32(SPORT1_TX32, val)
-#define bfin_read_SPORT1_RX32() bfin_read32(SPORT1_RX32)
-#define bfin_write_SPORT1_RX32(val) bfin_write32(SPORT1_RX32, val)
-#define bfin_read_SPORT1_TX16() bfin_read16(SPORT1_TX16)
-#define bfin_write_SPORT1_TX16(val) bfin_write16(SPORT1_TX16, val)
-#define bfin_read_SPORT1_RX16() bfin_read16(SPORT1_RX16)
-#define bfin_write_SPORT1_RX16(val) bfin_write16(SPORT1_RX16, val)
+#define bfin_read_SPORT1_TX32() bfin_read32(SPORT1_TX)
+#define bfin_write_SPORT1_TX32(val) bfin_write32(SPORT1_TX, val)
+#define bfin_read_SPORT1_RX32() bfin_read32(SPORT1_RX)
+#define bfin_write_SPORT1_RX32(val) bfin_write32(SPORT1_RX, val)
+#define bfin_read_SPORT1_TX16() bfin_read16(SPORT1_TX)
+#define bfin_write_SPORT1_TX16(val) bfin_write16(SPORT1_TX, val)
+#define bfin_read_SPORT1_RX16() bfin_read16(SPORT1_RX)
+#define bfin_write_SPORT1_RX16(val) bfin_write16(SPORT1_RX, val)
#define bfin_read_SPORT1_RCR1() bfin_read16(SPORT1_RCR1)
#define bfin_write_SPORT1_RCR1(val) bfin_write16(SPORT1_RCR1, val)
#define bfin_read_SPORT1_RCR2() bfin_read16(SPORT1_RCR2)
diff --git a/arch/blackfin/mach-bf527/include/mach/defBF52x_base.h b/arch/blackfin/mach-bf527/include/mach/defBF52x_base.h
index 3e00075..0947503 100644
--- a/arch/blackfin/mach-bf527/include/mach/defBF52x_base.h
+++ b/arch/blackfin/mach-bf527/include/mach/defBF52x_base.h
@@ -749,51 +749,6 @@
#define FFE 0x20 /* Force Framing Error On Transmit */
-/* *********** SERIAL PERIPHERAL INTERFACE (SPI) MASKS ****************************/
-/* SPI_CTL Masks */
-#define TIMOD 0x0003 /* Transfer Initiate Mode */
-#define RDBR_CORE 0x0000 /* RDBR Read Initiates, IRQ When RDBR Full */
-#define TDBR_CORE 0x0001 /* TDBR Write Initiates, IRQ When TDBR Empty */
-#define RDBR_DMA 0x0002 /* DMA Read, DMA Until FIFO Empty */
-#define TDBR_DMA 0x0003 /* DMA Write, DMA Until FIFO Full */
-#define SZ 0x0004 /* Send Zero (When TDBR Empty, Send Zero/Last*) */
-#define GM 0x0008 /* Get More (When RDBR Full, Overwrite/Discard*) */
-#define PSSE 0x0010 /* Slave-Select Input Enable */
-#define EMISO 0x0020 /* Enable MISO As Output */
-#define SIZE 0x0100 /* Size of Words (16/8* Bits) */
-#define LSBF 0x0200 /* LSB First */
-#define CPHA 0x0400 /* Clock Phase */
-#define CPOL 0x0800 /* Clock Polarity */
-#define MSTR 0x1000 /* Master/Slave* */
-#define WOM 0x2000 /* Write Open Drain Master */
-#define SPE 0x4000 /* SPI Enable */
-
-/* SPI_FLG Masks */
-#define FLS1 0x0002 /* Enables SPI_FLOUT1 as SPI Slave-Select Output */
-#define FLS2 0x0004 /* Enables SPI_FLOUT2 as SPI Slave-Select Output */
-#define FLS3 0x0008 /* Enables SPI_FLOUT3 as SPI Slave-Select Output */
-#define FLS4 0x0010 /* Enables SPI_FLOUT4 as SPI Slave-Select Output */
-#define FLS5 0x0020 /* Enables SPI_FLOUT5 as SPI Slave-Select Output */
-#define FLS6 0x0040 /* Enables SPI_FLOUT6 as SPI Slave-Select Output */
-#define FLS7 0x0080 /* Enables SPI_FLOUT7 as SPI Slave-Select Output */
-#define FLG1 0xFDFF /* Activates SPI_FLOUT1 */
-#define FLG2 0xFBFF /* Activates SPI_FLOUT2 */
-#define FLG3 0xF7FF /* Activates SPI_FLOUT3 */
-#define FLG4 0xEFFF /* Activates SPI_FLOUT4 */
-#define FLG5 0xDFFF /* Activates SPI_FLOUT5 */
-#define FLG6 0xBFFF /* Activates SPI_FLOUT6 */
-#define FLG7 0x7FFF /* Activates SPI_FLOUT7 */
-
-/* SPI_STAT Masks */
-#define SPIF 0x0001 /* SPI Finished (Single-Word Transfer Complete) */
-#define MODF 0x0002 /* Mode Fault Error (Another Device Tried To Become Master) */
-#define TXE 0x0004 /* Transmission Error (Data Sent With No New Data In TDBR) */
-#define TXS 0x0008 /* SPI_TDBR Data Buffer Status (Full/Empty*) */
-#define RBSY 0x0010 /* Receive Error (Data Received With RDBR Full) */
-#define RXS 0x0020 /* SPI_RDBR Data Buffer Status (Full/Empty*) */
-#define TXCOL 0x0040 /* Transmit Collision Error (Corrupt Data May Have Been Sent) */
-
-
/* **************** GENERAL PURPOSE TIMER MASKS **********************/
/* TIMER_ENABLE Masks */
#define TIMEN0 0x0001 /* Enable Timer 0 */
diff --git a/arch/blackfin/mach-bf533/boards/H8606.c b/arch/blackfin/mach-bf533/boards/H8606.c
index 175371a..2ce7b16 100644
--- a/arch/blackfin/mach-bf533/boards/H8606.c
+++ b/arch/blackfin/mach-bf533/boards/H8606.c
@@ -171,7 +171,7 @@
};
#endif
-#if defined(CONFIG_SND_BLACKFIN_AD183X) || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
@@ -206,12 +206,12 @@
},
#endif
-#if defined(CONFIG_SND_BLACKFIN_AD183X) || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
{
- .modalias = "ad1836",
+ .modalias = "ad183x",
.max_speed_hz = 16,
.bus_num = 1,
- .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+ .chip_select = 4,
.controller_data = &ad1836_spi_chip_info,
},
#endif
@@ -347,6 +347,7 @@
.membase = (void *)0x20200000,
.mapbase = 0x20200000,
.irq = IRQ_PF8,
+ .irqflags = IRQF_TRIGGER_HIGH,
.flags = UPF_BOOT_AUTOCONF | UART_CONFIG_TYPE,
.iotype = UPIO_MEM,
.regshift = 1,
@@ -355,6 +356,7 @@
.membase = (void *)0x20200010,
.mapbase = 0x20200010,
.irq = IRQ_PF8,
+ .irqflags = IRQF_TRIGGER_HIGH,
.flags = UPF_BOOT_AUTOCONF | UART_CONFIG_TYPE,
.iotype = UPIO_MEM,
.regshift = 1,
diff --git a/arch/blackfin/mach-bf533/boards/blackstamp.c b/arch/blackfin/mach-bf533/boards/blackstamp.c
index 84a06f6..20c1022 100644
--- a/arch/blackfin/mach-bf533/boards/blackstamp.c
+++ b/arch/blackfin/mach-bf533/boards/blackstamp.c
@@ -368,8 +368,8 @@
#include <linux/i2c-gpio.h>
static struct i2c_gpio_platform_data i2c_gpio_data = {
- .sda_pin = 8,
- .scl_pin = 9,
+ .sda_pin = GPIO_PF8,
+ .scl_pin = GPIO_PF9,
.sda_is_open_drain = 0,
.scl_is_open_drain = 0,
.udelay = 40,
diff --git a/arch/blackfin/mach-bf533/boards/cm_bf533.c b/arch/blackfin/mach-bf533/boards/cm_bf533.c
index fdcde61..adbe62a 100644
--- a/arch/blackfin/mach-bf533/boards/cm_bf533.c
+++ b/arch/blackfin/mach-bf533/boards/cm_bf533.c
@@ -71,7 +71,7 @@
};
#endif
-#if defined(CONFIG_SND_BLACKFIN_AD183X) || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
@@ -110,12 +110,12 @@
},
#endif
-#if defined(CONFIG_SND_BLACKFIN_AD183X) || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
{
- .modalias = "ad1836",
+ .modalias = "ad183x",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
- .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+ .chip_select = 4,
.controller_data = &ad1836_spi_chip_info,
},
#endif
@@ -400,7 +400,7 @@
}, {
.start = IRQ_PF4,
.end = IRQ_PF4,
- .flags = IORESOURCE_IRQ,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
},
};
diff --git a/arch/blackfin/mach-bf533/boards/ezkit.c b/arch/blackfin/mach-bf533/boards/ezkit.c
index 739773c..a1cb8e7 100644
--- a/arch/blackfin/mach-bf533/boards/ezkit.c
+++ b/arch/blackfin/mach-bf533/boards/ezkit.c
@@ -222,7 +222,7 @@
};
#endif
-#if defined(CONFIG_SND_BLACKFIN_AD183X) || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
@@ -261,12 +261,12 @@
},
#endif
-#if defined(CONFIG_SND_BLACKFIN_AD183X) || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
{
- .modalias = "ad1836",
+ .modalias = "ad183x",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
- .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+ .chip_select = 4,
.controller_data = &ad1836_spi_chip_info,
},
#endif
@@ -422,8 +422,8 @@
#include <linux/i2c-gpio.h>
static struct i2c_gpio_platform_data i2c_gpio_data = {
- .sda_pin = 1,
- .scl_pin = 0,
+ .sda_pin = GPIO_PF1,
+ .scl_pin = GPIO_PF0,
.sda_is_open_drain = 0,
.scl_is_open_drain = 0,
.udelay = 40,
diff --git a/arch/blackfin/mach-bf533/boards/ip0x.c b/arch/blackfin/mach-bf533/boards/ip0x.c
index b8474ca..5ba4b02 100644
--- a/arch/blackfin/mach-bf533/boards/ip0x.c
+++ b/arch/blackfin/mach-bf533/boards/ip0x.c
@@ -232,7 +232,7 @@
},{
.start = IRQ_PF11,
.end = IRQ_PF11,
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
},
};
diff --git a/arch/blackfin/mach-bf533/boards/stamp.c b/arch/blackfin/mach-bf533/boards/stamp.c
index 29c219e..b3b1cde 100644
--- a/arch/blackfin/mach-bf533/boards/stamp.c
+++ b/arch/blackfin/mach-bf533/boards/stamp.c
@@ -185,7 +185,7 @@
};
#endif
-#if defined(CONFIG_SND_BLACKFIN_AD183X) || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
@@ -252,13 +252,15 @@
},
#endif
-#if defined(CONFIG_SND_BLACKFIN_AD183X) || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
{
- .modalias = "ad1836",
+ .modalias = "ad183x",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
- .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+ .chip_select = 4,
+ .platform_data = "ad1836", /* only includes chip name for the moment */
.controller_data = &ad1836_spi_chip_info,
+ .mode = SPI_MODE_3,
},
#endif
@@ -495,8 +497,8 @@
#include <linux/i2c-gpio.h>
static struct i2c_gpio_platform_data i2c_gpio_data = {
- .sda_pin = 2,
- .scl_pin = 3,
+ .sda_pin = GPIO_PF2,
+ .scl_pin = GPIO_PF3,
.sda_is_open_drain = 0,
.scl_is_open_drain = 0,
.udelay = 40,
@@ -534,6 +536,11 @@
I2C_BOARD_INFO("bfin-adv7393", 0x2B),
},
#endif
+#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+ {
+ I2C_BOARD_INFO("ad5252", 0x2f),
+ },
+#endif
};
static const unsigned int cclk_vlev_datasheet[] =
diff --git a/arch/blackfin/mach-bf533/include/mach/defBF532.h b/arch/blackfin/mach-bf533/include/mach/defBF532.h
index 04acf1e..3adb0b4 100644
--- a/arch/blackfin/mach-bf533/include/mach/defBF532.h
+++ b/arch/blackfin/mach-bf533/include/mach/defBF532.h
@@ -681,76 +681,6 @@
#define PF14_P 14
#define PF15_P 15
-/* *********** SERIAL PERIPHERAL INTERFACE (SPI) MASKS **************** */
-
-/* SPI_CTL Masks */
-#define TIMOD 0x00000003 /* Transfer initiation mode and interrupt generation */
-#define RDBR_CORE 0x0000 /* RDBR Read Initiates, IRQ When RDBR Full */
-#define TDBR_CORE 0x0001 /* TDBR Write Initiates, IRQ When TDBR Empty */
-#define RDBR_DMA 0x0002 /* DMA Read, DMA Until FIFO Empty */
-#define TDBR_DMA 0x0003 /* DMA Write, DMA Until FIFO Full */
-#define SZ 0x00000004 /* Send Zero (=0) or last (=1) word when TDBR empty. */
-#define GM 0x00000008 /* When RDBR full, get more (=1) data or discard (=0) incoming Data */
-#define PSSE 0x00000010 /* Enable (=1) Slave-Select input for Master. */
-#define EMISO 0x00000020 /* Enable (=1) MISO pin as an output. */
-#define SIZE 0x00000100 /* Word length (0 => 8 bits, 1 => 16 bits) */
-#define LSBF 0x00000200 /* Data format (0 => MSB sent/received first 1 => LSB sent/received first) */
-#define CPHA 0x00000400 /* Clock phase (0 => SPICLK starts toggling in middle of xfer, 1 => SPICLK toggles at the beginning of xfer. */
-#define CPOL 0x00000800 /* Clock polarity (0 => active-high, 1 => active-low) */
-#define MSTR 0x00001000 /* Configures SPI as master (=1) or slave (=0) */
-#define WOM 0x00002000 /* Open drain (=1) data output enable (for MOSI and MISO) */
-#define SPE 0x00004000 /* SPI module enable (=1), disable (=0) */
-
-/* SPI_FLG Masks */
-#define FLS1 0x00000002 /* Enables (=1) SPI_FLOUT1 as flag output for SPI Slave-select */
-#define FLS2 0x00000004 /* Enables (=1) SPI_FLOUT2 as flag output for SPI Slave-select */
-#define FLS3 0x00000008 /* Enables (=1) SPI_FLOUT3 as flag output for SPI Slave-select */
-#define FLS4 0x00000010 /* Enables (=1) SPI_FLOUT4 as flag output for SPI Slave-select */
-#define FLS5 0x00000020 /* Enables (=1) SPI_FLOUT5 as flag output for SPI Slave-select */
-#define FLS6 0x00000040 /* Enables (=1) SPI_FLOUT6 as flag output for SPI Slave-select */
-#define FLS7 0x00000080 /* Enables (=1) SPI_FLOUT7 as flag output for SPI Slave-select */
-#define FLG1 0x00000200 /* Activates (=0) SPI_FLOUT1 as flag output for SPI Slave-select */
-#define FLG2 0x00000400 /* Activates (=0) SPI_FLOUT2 as flag output for SPI Slave-select */
-#define FLG3 0x00000800 /* Activates (=0) SPI_FLOUT3 as flag output for SPI Slave-select */
-#define FLG4 0x00001000 /* Activates (=0) SPI_FLOUT4 as flag output for SPI Slave-select */
-#define FLG5 0x00002000 /* Activates (=0) SPI_FLOUT5 as flag output for SPI Slave-select */
-#define FLG6 0x00004000 /* Activates (=0) SPI_FLOUT6 as flag output for SPI Slave-select */
-#define FLG7 0x00008000 /* Activates (=0) SPI_FLOUT7 as flag output for SPI Slave-select */
-
-/* SPI_FLG Bit Positions */
-#define FLS1_P 0x00000001 /* Enables (=1) SPI_FLOUT1 as flag output for SPI Slave-select */
-#define FLS2_P 0x00000002 /* Enables (=1) SPI_FLOUT2 as flag output for SPI Slave-select */
-#define FLS3_P 0x00000003 /* Enables (=1) SPI_FLOUT3 as flag output for SPI Slave-select */
-#define FLS4_P 0x00000004 /* Enables (=1) SPI_FLOUT4 as flag output for SPI Slave-select */
-#define FLS5_P 0x00000005 /* Enables (=1) SPI_FLOUT5 as flag output for SPI Slave-select */
-#define FLS6_P 0x00000006 /* Enables (=1) SPI_FLOUT6 as flag output for SPI Slave-select */
-#define FLS7_P 0x00000007 /* Enables (=1) SPI_FLOUT7 as flag output for SPI Slave-select */
-#define FLG1_P 0x00000009 /* Activates (=0) SPI_FLOUT1 as flag output for SPI Slave-select */
-#define FLG2_P 0x0000000A /* Activates (=0) SPI_FLOUT2 as flag output for SPI Slave-select */
-#define FLG3_P 0x0000000B /* Activates (=0) SPI_FLOUT3 as flag output for SPI Slave-select */
-#define FLG4_P 0x0000000C /* Activates (=0) SPI_FLOUT4 as flag output for SPI Slave-select */
-#define FLG5_P 0x0000000D /* Activates (=0) SPI_FLOUT5 as flag output for SPI Slave-select */
-#define FLG6_P 0x0000000E /* Activates (=0) SPI_FLOUT6 as flag output for SPI Slave-select */
-#define FLG7_P 0x0000000F /* Activates (=0) SPI_FLOUT7 as flag output for SPI Slave-select */
-
-/* SPI_STAT Masks */
-#define SPIF 0x00000001 /* Set (=1) when SPI single-word transfer complete */
-#define MODF 0x00000002 /* Set (=1) in a master device when some other device tries to become master */
-#define TXE 0x00000004 /* Set (=1) when transmission occurs with no new data in SPI_TDBR */
-#define TXS 0x00000008 /* SPI_TDBR Data Buffer Status (0=Empty, 1=Full) */
-#define RBSY 0x00000010 /* Set (=1) when data is received with RDBR full */
-#define RXS 0x00000020 /* SPI_RDBR Data Buffer Status (0=Empty, 1=Full) */
-#define TXCOL 0x00000040 /* When set (=1), corrupt data may have been transmitted */
-
-/* SPIx_FLG Masks */
-#define FLG1E 0xFDFF /* Activates SPI_FLOUT1 */
-#define FLG2E 0xFBFF /* Activates SPI_FLOUT2 */
-#define FLG3E 0xF7FF /* Activates SPI_FLOUT3 */
-#define FLG4E 0xEFFF /* Activates SPI_FLOUT4 */
-#define FLG5E 0xDFFF /* Activates SPI_FLOUT5 */
-#define FLG6E 0xBFFF /* Activates SPI_FLOUT6 */
-#define FLG7E 0x7FFF /* Activates SPI_FLOUT7 */
-
/* ********************* ASYNCHRONOUS MEMORY CONTROLLER MASKS ************* */
/* AMGCTL Masks */
diff --git a/arch/blackfin/mach-bf537/Kconfig b/arch/blackfin/mach-bf537/Kconfig
index d81224f..08b2b34 100644
--- a/arch/blackfin/mach-bf537/Kconfig
+++ b/arch/blackfin/mach-bf537/Kconfig
@@ -14,8 +14,8 @@
int "IRQ_DMA_ERROR Generic"
default 7
config IRQ_ERROR
- int "IRQ_ERROR: CAN MAC SPORT0 SPORT1 SPI UART0 UART1"
- default 7
+ int "IRQ_ERROR: PPI CAN MAC SPORT0 SPORT1 SPI UART0 UART1"
+ default 11
config IRQ_RTC
int "IRQ_RTC"
default 8
diff --git a/arch/blackfin/mach-bf537/boards/cm_bf537e.c b/arch/blackfin/mach-bf537/boards/cm_bf537e.c
index d35fc5f..e2e7be4 100644
--- a/arch/blackfin/mach-bf537/boards/cm_bf537e.c
+++ b/arch/blackfin/mach-bf537/boards/cm_bf537e.c
@@ -73,7 +73,7 @@
};
#endif
-#if defined(CONFIG_SND_BLACKFIN_AD183X) || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
@@ -112,12 +112,12 @@
},
#endif
-#if defined(CONFIG_SND_BLACKFIN_AD183X) || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
{
- .modalias = "ad1836",
+ .modalias = "ad183x",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
- .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+ .chip_select = 4,
.controller_data = &ad1836_spi_chip_info,
},
#endif
@@ -229,7 +229,7 @@
}, {
.start = IRQ_PG15,
.end = IRQ_PG15,
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
},
};
diff --git a/arch/blackfin/mach-bf537/boards/cm_bf537u.c b/arch/blackfin/mach-bf537/boards/cm_bf537u.c
index d464ad5..752c833 100644
--- a/arch/blackfin/mach-bf537/boards/cm_bf537u.c
+++ b/arch/blackfin/mach-bf537/boards/cm_bf537u.c
@@ -74,7 +74,7 @@
};
#endif
-#if defined(CONFIG_SND_BLACKFIN_AD183X) || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
@@ -113,12 +113,12 @@
},
#endif
-#if defined(CONFIG_SND_BLACKFIN_AD183X) || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
{
- .modalias = "ad1836",
+ .modalias = "ad183x",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
- .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+ .chip_select = 4,
.controller_data = &ad1836_spi_chip_info,
},
#endif
@@ -230,7 +230,7 @@
}, {
.start = IRQ_PG15,
.end = IRQ_PG15,
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
},
};
diff --git a/arch/blackfin/mach-bf537/boards/pnav10.c b/arch/blackfin/mach-bf537/boards/pnav10.c
index 812e8f9..6b03808 100644
--- a/arch/blackfin/mach-bf537/boards/pnav10.c
+++ b/arch/blackfin/mach-bf537/boards/pnav10.c
@@ -175,8 +175,8 @@
};
#endif
-#if defined(CONFIG_SND_BLACKFIN_AD183X) \
- || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
+ || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
@@ -238,13 +238,13 @@
},
#endif
-#if defined(CONFIG_SND_BLACKFIN_AD183X) \
- || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
+ || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
{
- .modalias = "ad1836",
+ .modalias = "ad183x",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
- .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+ .chip_select = 4,
.controller_data = &ad1836_spi_chip_info,
},
#endif
diff --git a/arch/blackfin/mach-bf537/boards/stamp.c b/arch/blackfin/mach-bf537/boards/stamp.c
index 68a27bc..c9e0e85 100644
--- a/arch/blackfin/mach-bf537/boards/stamp.c
+++ b/arch/blackfin/mach-bf537/boards/stamp.c
@@ -35,12 +35,10 @@
#include <asm/reboot.h>
#include <asm/portmux.h>
#include <asm/dpmc.h>
-#ifdef CONFIG_REGULATOR_ADP_SWITCH
-#include <linux/regulator/adp_switch.h>
+#ifdef CONFIG_REGULATOR_FIXED_VOLTAGE
+#include <linux/regulator/fixed.h>
#endif
-#ifdef CONFIG_REGULATOR_AD5398
-#include <linux/regulator/ad5398.h>
-#endif
+#include <linux/regulator/machine.h>
#include <linux/regulator/consumer.h>
#include <linux/regulator/userspace-consumer.h>
@@ -264,7 +262,7 @@
}, {
.start = IRQ_PF3,
.end = IRQ_PF3,
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
},
};
@@ -418,7 +416,7 @@
static struct resource bfin_plat_nand_resources = {
.start = 0x20212000,
.end = 0x20212000 + (1 << MAX(BFIN_NAND_PLAT_CLE, BFIN_NAND_PLAT_ALE)),
- .flags = IORESOURCE_IO,
+ .flags = IORESOURCE_MEM,
};
static struct platform_device bfin_async_nand_device = {
@@ -545,6 +543,14 @@
};
#endif
+#if defined(CONFIG_SND_BF5XX_SOC_ADAV80X) \
+ || defined(CONFIG_SND_BF5XX_SOC_ADAV80X_MODULE)
+static struct bfin5xx_spi_chip adav801_spi_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 8,
+};
+#endif
+
#if defined(CONFIG_INPUT_AD714X_SPI) || defined(CONFIG_INPUT_AD714X_SPI_MODULE)
#include <linux/input/ad714x.h>
static struct bfin5xx_spi_chip ad7147_spi_chip_info = {
@@ -693,6 +699,65 @@
};
#endif
+#if defined(CONFIG_AD7314) || defined(CONFIG_AD7314_MODULE)
+static struct bfin5xx_spi_chip ad7314_spi_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_AD7816) || defined(CONFIG_AD7816_MODULE)
+static unsigned short ad7816_platform_data[] = {
+ GPIO_PF4, /* rdwr_pin */
+ GPIO_PF5, /* convert_pin */
+ GPIO_PF7, /* busy_pin */
+ 0,
+};
+
+static struct bfin5xx_spi_chip ad7816_spi_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_ADT7310) || defined(CONFIG_ADT7310_MODULE)
+static unsigned long adt7310_platform_data[3] = {
+/* INT bound temperature alarm event. line 1 */
+ IRQ_PG4, IRQF_TRIGGER_LOW,
+/* CT bound temperature alarm event irq_flags. line 0 */
+ IRQF_TRIGGER_LOW,
+};
+
+static struct bfin5xx_spi_chip adt7310_spi_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_AD7298) || defined(CONFIG_AD7298_MODULE)
+static unsigned short ad7298_platform_data[] = {
+ GPIO_PF7, /* busy_pin */
+ 0,
+};
+
+static struct bfin5xx_spi_chip ad7298_spi_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_ADT7316_SPI) || defined(CONFIG_ADT7316_SPI_MODULE)
+static unsigned long adt7316_spi_data[2] = {
+ IRQF_TRIGGER_LOW, /* interrupt flags */
+ GPIO_PF7, /* ldac_pin, 0 means DAC/LDAC registers control DAC update */
+};
+
+static struct bfin5xx_spi_chip adt7316_spi_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 8,
+};
+#endif
+
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
#define MMC_SPI_CARD_DETECT_INT IRQ_PF5
@@ -824,14 +889,12 @@
static struct bfin5xx_spi_chip enc28j60_spi_chip_info = {
.enable_dma = 1,
.bits_per_word = 8,
- .cs_gpio = GPIO_PF10,
};
#endif
#if defined(CONFIG_ADF702X) || defined(CONFIG_ADF702X_MODULE)
static struct bfin5xx_spi_chip adf7021_spi_chip_info = {
.bits_per_word = 16,
- .cs_gpio = GPIO_PF10,
};
#include <linux/spi/adf702x.h>
@@ -938,6 +1001,13 @@
};
#endif
+#if defined(CONFIG_AD7476) || defined(CONFIG_AD7476_MODULE)
+static struct bfin5xx_spi_chip spi_ad7476_chip_info = {
+ .enable_dma = 0, /* use dma transfer with this chip*/
+ .bits_per_word = 8,
+};
+#endif
+
static struct spi_board_info bfin_spi_board_info[] __initdata = {
#if defined(CONFIG_MTD_M25P80) \
|| defined(CONFIG_MTD_M25P80_MODULE)
@@ -982,7 +1052,7 @@
.modalias = "ad183x",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
- .chip_select = 4,/* CONFIG_SND_BLACKFIN_SPI_PFBIT */
+ .chip_select = 4,
.platform_data = "ad1836", /* only includes chip name for the moment */
.controller_data = &ad1836_spi_chip_info,
.mode = SPI_MODE_3,
@@ -1000,6 +1070,17 @@
},
#endif
+#if defined(CONFIG_SND_BF5XX_SOC_ADAV80X) || defined(CONFIG_SND_BF5XX_SOC_ADAV80X_MODULE)
+ {
+ .modalias = "adav80x",
+ .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 1,
+ .controller_data = &adav801_spi_chip_info,
+ .mode = SPI_MODE_3,
+ },
+#endif
+
#if defined(CONFIG_INPUT_AD714X_SPI) || defined(CONFIG_INPUT_AD714X_SPI_MODULE)
{
.modalias = "ad714x_captouch",
@@ -1018,6 +1099,7 @@
.modalias = "ad2s90",
.bus_num = 0,
.chip_select = 3, /* change it for your board */
+ .mode = SPI_MODE_3,
.platform_data = NULL,
.controller_data = &ad2s90_spi_chip_info,
},
@@ -1044,6 +1126,67 @@
},
#endif
+#if defined(CONFIG_AD7314) || defined(CONFIG_AD7314_MODULE)
+ {
+ .modalias = "ad7314",
+ .max_speed_hz = 1000000,
+ .bus_num = 0,
+ .chip_select = 4, /* CS, change it for your board */
+ .controller_data = &ad7314_spi_chip_info,
+ .mode = SPI_MODE_1,
+ },
+#endif
+
+#if defined(CONFIG_AD7816) || defined(CONFIG_AD7816_MODULE)
+ {
+ .modalias = "ad7818",
+ .max_speed_hz = 1000000,
+ .bus_num = 0,
+ .chip_select = 4, /* CS, change it for your board */
+ .platform_data = ad7816_platform_data,
+ .controller_data = &ad7816_spi_chip_info,
+ .mode = SPI_MODE_3,
+ },
+#endif
+
+#if defined(CONFIG_ADT7310) || defined(CONFIG_ADT7310_MODULE)
+ {
+ .modalias = "adt7310",
+ .max_speed_hz = 1000000,
+ .irq = IRQ_PG5, /* CT alarm event. Line 0 */
+ .bus_num = 0,
+ .chip_select = 4, /* CS, change it for your board */
+ .platform_data = adt7310_platform_data,
+ .controller_data = &adt7310_spi_chip_info,
+ .mode = SPI_MODE_3,
+ },
+#endif
+
+#if defined(CONFIG_AD7298) || defined(CONFIG_AD7298_MODULE)
+ {
+ .modalias = "ad7298",
+ .max_speed_hz = 1000000,
+ .bus_num = 0,
+ .chip_select = 4, /* CS, change it for your board */
+ .platform_data = ad7298_platform_data,
+ .controller_data = &ad7298_spi_chip_info,
+ .mode = SPI_MODE_3,
+ },
+#endif
+
+#if defined(CONFIG_ADT7316_SPI) || defined(CONFIG_ADT7316_SPI_MODULE)
+ {
+ .modalias = "adt7316",
+ .max_speed_hz = 1000000,
+ .irq = IRQ_PG5, /* interrupt line */
+ .bus_num = 0,
+ .chip_select = 4, /* CS, change it for your board */
+ .platform_data = adt7316_spi_data,
+ .controller_data = &adt7316_spi_chip_info,
+ .mode = SPI_MODE_3,
+ },
+#endif
+
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
{
.modalias = "mmc_spi",
@@ -1103,7 +1246,7 @@
.max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
.irq = IRQ_PF6,
.bus_num = 0,
- .chip_select = 0, /* GPIO controlled SSEL */
+ .chip_select = GPIO_PF10 + MAX_CTRL_CS, /* GPIO controlled SSEL */
.controller_data = &enc28j60_spi_chip_info,
.mode = SPI_MODE_0,
},
@@ -1125,7 +1268,7 @@
.modalias = "adf702x",
.max_speed_hz = 16000000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
- .chip_select = 0, /* GPIO controlled SSEL */
+ .chip_select = GPIO_PF10 + MAX_CTRL_CS, /* GPIO controlled SSEL */
.controller_data = &adf7021_spi_chip_info,
.platform_data = &adf7021_platform_data,
.mode = SPI_MODE_0,
@@ -1143,12 +1286,239 @@
.mode = SPI_MODE_0,
},
#endif
+#if defined(CONFIG_AD7476) \
+ || defined(CONFIG_AD7476_MODULE)
+ {
+ .modalias = "ad7476", /* Name of spi_driver for this device */
+ .max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0, /* Framework bus number */
+ .chip_select = 1, /* Framework chip select. */
+ .platform_data = NULL, /* No spi_driver specific config */
+ .controller_data = &spi_ad7476_chip_info,
+ .mode = SPI_MODE_3,
+ },
+#endif
+#if defined(CONFIG_ADE7753) \
+ || defined(CONFIG_ADE7753_MODULE)
+ {
+ .modalias = "ade7753",
+ .max_speed_hz = 1000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 1, /* CS, change it for your board */
+ .platform_data = NULL, /* No spi_driver specific config */
+ .mode = SPI_MODE_1,
+ },
+#endif
+#if defined(CONFIG_ADE7754) \
+ || defined(CONFIG_ADE7754_MODULE)
+ {
+ .modalias = "ade7754",
+ .max_speed_hz = 1000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 1, /* CS, change it for your board */
+ .platform_data = NULL, /* No spi_driver specific config */
+ .mode = SPI_MODE_1,
+ },
+#endif
+#if defined(CONFIG_ADE7758) \
+ || defined(CONFIG_ADE7758_MODULE)
+ {
+ .modalias = "ade7758",
+ .max_speed_hz = 1000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 1, /* CS, change it for your board */
+ .platform_data = NULL, /* No spi_driver specific config */
+ .mode = SPI_MODE_1,
+ },
+#endif
+#if defined(CONFIG_ADE7759) \
+ || defined(CONFIG_ADE7759_MODULE)
+ {
+ .modalias = "ade7759",
+ .max_speed_hz = 1000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 1, /* CS, change it for your board */
+ .platform_data = NULL, /* No spi_driver specific config */
+ .mode = SPI_MODE_1,
+ },
+#endif
+#if defined(CONFIG_ADE7854_SPI) \
+ || defined(CONFIG_ADE7854_SPI_MODULE)
+ {
+ .modalias = "ade7854",
+ .max_speed_hz = 1000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 1, /* CS, change it for your board */
+ .platform_data = NULL, /* No spi_driver specific config */
+ .mode = SPI_MODE_3,
+ },
+#endif
+#if defined(CONFIG_ADIS16060) \
+ || defined(CONFIG_ADIS16060_MODULE)
+ {
+ .modalias = "adis16060_r",
+ .max_speed_hz = 2900000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = MAX_CTRL_CS + 1, /* CS for read, change it for your board */
+ .platform_data = NULL, /* No spi_driver specific config */
+ .mode = SPI_MODE_0,
+ },
+ {
+ .modalias = "adis16060_w",
+ .max_speed_hz = 2900000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 2, /* CS for write, change it for your board */
+ .platform_data = NULL, /* No spi_driver specific config */
+ .mode = SPI_MODE_1,
+ },
+#endif
+#if defined(CONFIG_ADIS16130) \
+ || defined(CONFIG_ADIS16130_MODULE)
+ {
+ .modalias = "adis16130",
+ .max_speed_hz = 1000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 1, /* CS for read, change it for your board */
+ .platform_data = NULL, /* No spi_driver specific config */
+ .mode = SPI_MODE_3,
+ },
+#endif
+#if defined(CONFIG_ADIS16201) \
+ || defined(CONFIG_ADIS16201_MODULE)
+ {
+ .modalias = "adis16201",
+ .max_speed_hz = 1000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 5, /* CS, change it for your board */
+ .platform_data = NULL, /* No spi_driver specific config */
+ .mode = SPI_MODE_3,
+ .irq = IRQ_PF4,
+ },
+#endif
+#if defined(CONFIG_ADIS16203) \
+ || defined(CONFIG_ADIS16203_MODULE)
+ {
+ .modalias = "adis16203",
+ .max_speed_hz = 1000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 5, /* CS, change it for your board */
+ .platform_data = NULL, /* No spi_driver specific config */
+ .mode = SPI_MODE_3,
+ .irq = IRQ_PF4,
+ },
+#endif
+#if defined(CONFIG_ADIS16204) \
+ || defined(CONFIG_ADIS16204_MODULE)
+ {
+ .modalias = "adis16204",
+ .max_speed_hz = 1000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 5, /* CS, change it for your board */
+ .platform_data = NULL, /* No spi_driver specific config */
+ .mode = SPI_MODE_3,
+ .irq = IRQ_PF4,
+ },
+#endif
+#if defined(CONFIG_ADIS16209) \
+ || defined(CONFIG_ADIS16209_MODULE)
+ {
+ .modalias = "adis16209",
+ .max_speed_hz = 1000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 5, /* CS, change it for your board */
+ .platform_data = NULL, /* No spi_driver specific config */
+ .mode = SPI_MODE_3,
+ .irq = IRQ_PF4,
+ },
+#endif
+#if defined(CONFIG_ADIS16220) \
+ || defined(CONFIG_ADIS16220_MODULE)
+ {
+ .modalias = "adis16220",
+ .max_speed_hz = 2000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 5, /* CS, change it for your board */
+ .platform_data = NULL, /* No spi_driver specific config */
+ .mode = SPI_MODE_3,
+ .irq = IRQ_PF4,
+ },
+#endif
+#if defined(CONFIG_ADIS16240) \
+ || defined(CONFIG_ADIS16240_MODULE)
+ {
+ .modalias = "adis16240",
+ .max_speed_hz = 1500000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 5, /* CS, change it for your board */
+ .platform_data = NULL, /* No spi_driver specific config */
+ .mode = SPI_MODE_3,
+ .irq = IRQ_PF4,
+ },
+#endif
+#if defined(CONFIG_ADIS16260) \
+ || defined(CONFIG_ADIS16260_MODULE)
+ {
+ .modalias = "adis16260",
+ .max_speed_hz = 1500000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 5, /* CS, change it for your board */
+ .platform_data = NULL, /* No spi_driver specific config */
+ .mode = SPI_MODE_3,
+ .irq = IRQ_PF4,
+ },
+#endif
+#if defined(CONFIG_ADIS16261) \
+ || defined(CONFIG_ADIS16261_MODULE)
+ {
+ .modalias = "adis16261",
+ .max_speed_hz = 2500000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 1, /* CS, change it for your board */
+ .platform_data = NULL, /* No spi_driver specific config */
+ .mode = SPI_MODE_3,
+ },
+#endif
+#if defined(CONFIG_ADIS16300) \
+ || defined(CONFIG_ADIS16300_MODULE)
+ {
+ .modalias = "adis16300",
+ .max_speed_hz = 1000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 5, /* CS, change it for your board */
+ .platform_data = NULL, /* No spi_driver specific config */
+ .mode = SPI_MODE_3,
+ .irq = IRQ_PF4,
+ },
+#endif
+#if defined(CONFIG_ADIS16350) \
+ || defined(CONFIG_ADIS16350_MODULE)
+ {
+ .modalias = "adis16364",
+ .max_speed_hz = 1000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 5, /* CS, change it for your board */
+ .platform_data = NULL, /* No spi_driver specific config */
+ .mode = SPI_MODE_3,
+ .irq = IRQ_PF4,
+ },
+#endif
+#if defined(CONFIG_ADIS16400) \
+ || defined(CONFIG_ADIS16400_MODULE)
+ {
+ .modalias = "adis16400",
+ .max_speed_hz = 1000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 1, /* CS, change it for your board */
+ .platform_data = NULL, /* No spi_driver specific config */
+ .mode = SPI_MODE_3,
+ },
+#endif
};
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
/* SPI controller data */
static struct bfin5xx_spi_master bfin_spi0_info = {
- .num_chipselect = 8,
+ .num_chipselect = MAX_CTRL_CS + MAX_BLACKFIN_GPIOS,
.enable_dma = 1, /* master has the ability to do dma transfer */
.pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
};
@@ -1773,12 +2143,6 @@
.consumer_supplies = &ad5398_consumer,
};
-static struct ad5398_platform_data ad5398_i2c_platform_data = {
- .current_bits = 10,
- .current_offset = 4,
- .regulator_data = &ad5398_regulator_data,
-};
-
#if defined(CONFIG_REGULATOR_VIRTUAL_CONSUMER) || \
defined(CONFIG_REGULATOR_VIRTUAL_CONSUMER_MODULE)
static struct platform_device ad5398_virt_consumer_device = {
@@ -1811,7 +2175,34 @@
#endif
#endif
+#if defined(CONFIG_ADT7410) || defined(CONFIG_ADT7410_MODULE)
+/* INT bound temperature alarm event. line 1 */
+static unsigned long adt7410_platform_data[2] = {
+ IRQ_PG4, IRQF_TRIGGER_LOW,
+};
+#endif
+
+#if defined(CONFIG_ADT7316_I2C) || defined(CONFIG_ADT7316_I2C_MODULE)
+/* INT bound temperature alarm event. line 1 */
+static unsigned long adt7316_i2c_data[2] = {
+ IRQF_TRIGGER_LOW, /* interrupt flags */
+ GPIO_PF4, /* ldac_pin, 0 means DAC/LDAC registers control DAC update */
+};
+#endif
+
static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
+#if defined(CONFIG_SND_BF5XX_SOC_AD193X) || defined(CONFIG_SND_BF5XX_SOC_AD193X_MODULE)
+ {
+ I2C_BOARD_INFO("ad1937", 0x04),
+ },
+#endif
+
+#if defined(CONFIG_SND_BF5XX_SOC_ADAV80X) || defined(CONFIG_SND_BF5XX_SOC_ADAV80X_MODULE)
+ {
+ I2C_BOARD_INFO("adav803", 0x10),
+ },
+#endif
+
#if defined(CONFIG_INPUT_AD714X_I2C) || defined(CONFIG_INPUT_AD714X_I2C_MODULE)
{
I2C_BOARD_INFO("ad7142_captouch", 0x2C),
@@ -1843,12 +2234,7 @@
{
I2C_BOARD_INFO("ad7414", 0x9),
.irq = IRQ_PG5,
- /*
- * platform_data pointer is borrwoed by the driver to
- * store custimer defined IRQ ALART level mode.
- * only IRQF_TRIGGER_HIGH and IRQF_TRIGGER_LOW are valid.
- */
- .platform_data = (void *)IRQF_TRIGGER_LOW,
+ .irq_flags = IRQF_TRIGGER_LOW,
},
#endif
@@ -1856,12 +2242,56 @@
{
I2C_BOARD_INFO("ad7417", 0xb),
.irq = IRQ_PG5,
- /*
- * platform_data pointer is borrwoed by the driver to
- * store custimer defined IRQ ALART level mode.
- * only IRQF_TRIGGER_HIGH and IRQF_TRIGGER_LOW are valid.
- */
- .platform_data = (void *)IRQF_TRIGGER_LOW,
+ .irq_flags = IRQF_TRIGGER_LOW,
+ .platform_data = (void *)GPIO_PF4,
+ },
+#endif
+
+#if defined(CONFIG_ADE7854_I2C) || defined(CONFIG_ADE7854_I2C_MODULE)
+ {
+ I2C_BOARD_INFO("ade7854", 0x38),
+ },
+#endif
+
+#if defined(CONFIG_ADT75) || defined(CONFIG_ADT75_MODULE)
+ {
+ I2C_BOARD_INFO("adt75", 0x9),
+ .irq = IRQ_PG5,
+ .irq_flags = IRQF_TRIGGER_LOW,
+ },
+#endif
+
+#if defined(CONFIG_ADT7408) || defined(CONFIG_ADT7408_MODULE)
+ {
+ I2C_BOARD_INFO("adt7408", 0x18),
+ .irq = IRQ_PG5,
+ .irq_flags = IRQF_TRIGGER_LOW,
+ },
+#endif
+
+#if defined(CONFIG_ADT7410) || defined(CONFIG_ADT7410_MODULE)
+ {
+ I2C_BOARD_INFO("adt7410", 0x48),
+ /* CT critical temperature event. line 0 */
+ .irq = IRQ_PG5,
+ .irq_flags = IRQF_TRIGGER_LOW,
+ .platform_data = (void *)&adt7410_platform_data,
+ },
+#endif
+
+#if defined(CONFIG_AD7291) || defined(CONFIG_AD7291_MODULE)
+ {
+ I2C_BOARD_INFO("ad7291", 0x20),
+ .irq = IRQ_PG5,
+ .irq_flags = IRQF_TRIGGER_LOW,
+ },
+#endif
+
+#if defined(CONFIG_ADT7316_I2C) || defined(CONFIG_ADT7316_I2C_MODULE)
+ {
+ I2C_BOARD_INFO("adt7316", 0x48),
+ .irq = IRQ_PG6,
+ .platform_data = (void *)&adt7316_i2c_data,
},
#endif
@@ -1917,7 +2347,7 @@
#endif
#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
{
- I2C_BOARD_INFO("bf537-lq035-ad5280", 0x2C),
+ I2C_BOARD_INFO("bf537-lq035-ad5280", 0x2F),
},
#endif
#if defined(CONFIG_BACKLIGHT_ADP8870) || defined(CONFIG_BACKLIGHT_ADP8870_MODULE)
@@ -1954,7 +2384,7 @@
#if defined(CONFIG_REGULATOR_AD5398) || defined(CONFIG_REGULATOR_AD5398_MODULE)
{
I2C_BOARD_INFO("ad5398", 0xC),
- .platform_data = (void *)&ad5398_i2c_platform_data,
+ .platform_data = (void *)&ad5398_regulator_data,
},
#endif
#if defined(CONFIG_BACKLIGHT_ADP8860) || defined(CONFIG_BACKLIGHT_ADP8860_MODULE)
@@ -1963,6 +2393,16 @@
.platform_data = (void *)&adp8860_pdata,
},
#endif
+#if defined(CONFIG_SND_SOC_ADAU1373) || defined(CONFIG_SND_SOC_ADAU1373_MODULE)
+ {
+ I2C_BOARD_INFO("adau1373", 0x1A),
+ },
+#endif
+#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+ {
+ I2C_BOARD_INFO("ad5252", 0x2e),
+ },
+#endif
};
#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
@@ -2147,50 +2587,38 @@
};
#endif
-#if defined(CONFIG_REGULATOR_ADP_SWITCH) || defined(CONFIG_REGULATOR_ADP_SWITCH_MODULE)
-#define REGULATOR_ADP122 "adp122"
-#define REGULATOR_ADP150 "adp150"
+#if defined(CONFIG_REGULATOR_FIXED_VOLTAGE) || defined(CONFIG_REGULATOR_FIXED_VOLTAGE_MODULE)
+#define REGULATOR_ADP122 "adp122"
+#define REGULATOR_ADP122_UV 2500000
static struct regulator_consumer_supply adp122_consumers = {
.supply = REGULATOR_ADP122,
};
-static struct regulator_consumer_supply adp150_consumers = {
- .supply = REGULATOR_ADP150,
+static struct regulator_init_data adp_switch_regulator_data = {
+ .constraints = {
+ .name = REGULATOR_ADP122,
+ .valid_ops_mask = REGULATOR_CHANGE_STATUS,
+ .min_uV = REGULATOR_ADP122_UV,
+ .max_uV = REGULATOR_ADP122_UV,
+ .min_uA = 0,
+ .max_uA = 300000,
+ },
+ .num_consumer_supplies = 1, /* only 1 */
+ .consumer_supplies = &adp122_consumers,
};
-static struct regulator_init_data adp_switch_regulator_data[] = {
- {
- .constraints = {
- .name = REGULATOR_ADP122,
- .valid_ops_mask = REGULATOR_CHANGE_STATUS,
- .min_uA = 0,
- .max_uA = 300000,
- },
- .num_consumer_supplies = 1, /* only 1 */
- .consumer_supplies = &adp122_consumers,
- .driver_data = (void *)GPIO_PF2, /* gpio port only */
- },
- {
- .constraints = {
- .name = REGULATOR_ADP150,
- .valid_ops_mask = REGULATOR_CHANGE_STATUS,
- .min_uA = 0,
- .max_uA = 150000,
- },
- .num_consumer_supplies = 1, /* only 1 */
- .consumer_supplies = &adp150_consumers,
- .driver_data = (void *)GPIO_PF3, /* gpio port only */
- },
-};
-
-static struct adp_switch_platform_data adp_switch_pdata = {
- .regulator_num = ARRAY_SIZE(adp_switch_regulator_data),
- .regulator_data = adp_switch_regulator_data,
+static struct fixed_voltage_config adp_switch_pdata = {
+ .supply_name = REGULATOR_ADP122,
+ .microvolts = REGULATOR_ADP122_UV,
+ .gpio = GPIO_PF2,
+ .enable_high = 1,
+ .enabled_at_boot = 0,
+ .init_data = &adp_switch_regulator_data,
};
static struct platform_device adp_switch_device = {
- .name = "adp_switch",
+ .name = "reg-fixed-voltage",
.id = 0,
.dev = {
.platform_data = &adp_switch_pdata,
@@ -2216,27 +2644,26 @@
.platform_data = &adp122_userspace_comsumer_data,
},
};
+#endif
+#endif
-static struct regulator_bulk_data adp150_bulk_data = {
- .supply = REGULATOR_ADP150,
-};
+#if defined(CONFIG_IIO_GPIO_TRIGGER) || \
+ defined(CONFIG_IIO_GPIO_TRIGGER_MODULE)
-static struct regulator_userspace_consumer_data adp150_userspace_comsumer_data = {
- .name = REGULATOR_ADP150,
- .num_supplies = 1,
- .supplies = &adp150_bulk_data,
-};
-
-static struct platform_device adp150_userspace_consumer_device = {
- .name = "reg-userspace-consumer",
- .id = 1,
- .dev = {
- .platform_data = &adp150_userspace_comsumer_data,
+static struct resource iio_gpio_trigger_resources[] = {
+ [0] = {
+ .start = IRQ_PF5,
+ .end = IRQ_PF5,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
},
};
-#endif
-#endif
+static struct platform_device iio_gpio_trigger = {
+ .name = "iio_gpio_trigger",
+ .num_resources = ARRAY_SIZE(iio_gpio_trigger_resources),
+ .resource = iio_gpio_trigger_resources,
+};
+#endif
static struct platform_device *stamp_devices[] __initdata = {
@@ -2369,14 +2796,18 @@
#endif
#endif
-#if defined(CONFIG_REGULATOR_ADP_SWITCH) || defined(CONFIG_REGULATOR_ADP_SWITCH_MODULE)
+#if defined(CONFIG_REGULATOR_FIXED_VOLTAGE) || defined(CONFIG_REGULATOR_FIXED_VOLTAGE_MODULE)
&adp_switch_device,
#if defined(CONFIG_REGULATOR_USERSPACE_CONSUMER) || \
defined(CONFIG_REGULATOR_USERSPACE_CONSUMER_MODULE)
&adp122_userspace_consumer_device,
- &adp150_userspace_consumer_device,
#endif
#endif
+
+#if defined(CONFIG_IIO_GPIO_TRIGGER) || \
+ defined(CONFIG_IIO_GPIO_TRIGGER_MODULE)
+ &iio_gpio_trigger,
+#endif
};
static int __init stamp_init(void)
diff --git a/arch/blackfin/mach-bf537/boards/tcm_bf537.c b/arch/blackfin/mach-bf537/boards/tcm_bf537.c
index 4f0a2e7..a4d62b5 100644
--- a/arch/blackfin/mach-bf537/boards/tcm_bf537.c
+++ b/arch/blackfin/mach-bf537/boards/tcm_bf537.c
@@ -74,7 +74,7 @@
};
#endif
-#if defined(CONFIG_SND_BLACKFIN_AD183X) || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
@@ -113,12 +113,12 @@
},
#endif
-#if defined(CONFIG_SND_BLACKFIN_AD183X) || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
{
- .modalias = "ad1836",
+ .modalias = "ad183x",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
- .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+ .chip_select = 4,
.controller_data = &ad1836_spi_chip_info,
},
#endif
@@ -230,7 +230,7 @@
}, {
.start = IRQ_PG15,
.end = IRQ_PG15,
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
},
};
diff --git a/arch/blackfin/mach-bf537/include/mach/defBF534.h b/arch/blackfin/mach-bf537/include/mach/defBF534.h
index 6f56907..0323e6b 100644
--- a/arch/blackfin/mach-bf537/include/mach/defBF534.h
+++ b/arch/blackfin/mach-bf537/include/mach/defBF534.h
@@ -1071,50 +1071,6 @@
#define FPE 0x10 /* Force Parity Error On Transmit */
#define FFE 0x20 /* Force Framing Error On Transmit */
-/* *********** SERIAL PERIPHERAL INTERFACE (SPI) MASKS ****************************/
-/* SPI_CTL Masks */
-#define TIMOD 0x0003 /* Transfer Initiate Mode */
-#define RDBR_CORE 0x0000 /* RDBR Read Initiates, IRQ When RDBR Full */
-#define TDBR_CORE 0x0001 /* TDBR Write Initiates, IRQ When TDBR Empty */
-#define RDBR_DMA 0x0002 /* DMA Read, DMA Until FIFO Empty */
-#define TDBR_DMA 0x0003 /* DMA Write, DMA Until FIFO Full */
-#define SZ 0x0004 /* Send Zero (When TDBR Empty, Send Zero/Last*) */
-#define GM 0x0008 /* Get More (When RDBR Full, Overwrite/Discard*) */
-#define PSSE 0x0010 /* Slave-Select Input Enable */
-#define EMISO 0x0020 /* Enable MISO As Output */
-#define SIZE 0x0100 /* Size of Words (16/8* Bits) */
-#define LSBF 0x0200 /* LSB First */
-#define CPHA 0x0400 /* Clock Phase */
-#define CPOL 0x0800 /* Clock Polarity */
-#define MSTR 0x1000 /* Master/Slave* */
-#define WOM 0x2000 /* Write Open Drain Master */
-#define SPE 0x4000 /* SPI Enable */
-
-/* SPI_FLG Masks */
-#define FLS1 0x0002 /* Enables SPI_FLOUT1 as SPI Slave-Select Output */
-#define FLS2 0x0004 /* Enables SPI_FLOUT2 as SPI Slave-Select Output */
-#define FLS3 0x0008 /* Enables SPI_FLOUT3 as SPI Slave-Select Output */
-#define FLS4 0x0010 /* Enables SPI_FLOUT4 as SPI Slave-Select Output */
-#define FLS5 0x0020 /* Enables SPI_FLOUT5 as SPI Slave-Select Output */
-#define FLS6 0x0040 /* Enables SPI_FLOUT6 as SPI Slave-Select Output */
-#define FLS7 0x0080 /* Enables SPI_FLOUT7 as SPI Slave-Select Output */
-#define FLG1 0xFDFF /* Activates SPI_FLOUT1 */
-#define FLG2 0xFBFF /* Activates SPI_FLOUT2 */
-#define FLG3 0xF7FF /* Activates SPI_FLOUT3 */
-#define FLG4 0xEFFF /* Activates SPI_FLOUT4 */
-#define FLG5 0xDFFF /* Activates SPI_FLOUT5 */
-#define FLG6 0xBFFF /* Activates SPI_FLOUT6 */
-#define FLG7 0x7FFF /* Activates SPI_FLOUT7 */
-
-/* SPI_STAT Masks */
-#define SPIF 0x0001 /* SPI Finished (Single-Word Transfer Complete) */
-#define MODF 0x0002 /* Mode Fault Error (Another Device Tried To Become Master) */
-#define TXE 0x0004 /* Transmission Error (Data Sent With No New Data In TDBR) */
-#define TXS 0x0008 /* SPI_TDBR Data Buffer Status (Full/Empty*) */
-#define RBSY 0x0010 /* Receive Error (Data Received With RDBR Full) */
-#define RXS 0x0020 /* SPI_RDBR Data Buffer Status (Full/Empty*) */
-#define TXCOL 0x0040 /* Transmit Collision Error (Corrupt Data May Have Been Sent) */
-
/* **************** GENERAL PURPOSE TIMER MASKS **********************/
/* TIMER_ENABLE Masks */
#define TIMEN0 0x0001 /* Enable Timer 0 */
diff --git a/arch/blackfin/mach-bf538/boards/ezkit.c b/arch/blackfin/mach-bf538/boards/ezkit.c
index 1a1f658..c6fb0a5 100644
--- a/arch/blackfin/mach-bf538/boards/ezkit.c
+++ b/arch/blackfin/mach-bf538/boards/ezkit.c
@@ -695,7 +695,7 @@
};
static struct bfin5xx_spi_master bf538_spi_master_info1 = {
- .num_chipselect = 8,
+ .num_chipselect = 2,
.enable_dma = 1, /* master has the ability to do dma transfer */
.pin_req = {P_SPI1_SCK, P_SPI1_MISO, P_SPI1_MOSI, 0},
};
@@ -711,7 +711,7 @@
};
static struct bfin5xx_spi_master bf538_spi_master_info2 = {
- .num_chipselect = 8,
+ .num_chipselect = 2,
.enable_dma = 1, /* master has the ability to do dma transfer */
.pin_req = {P_SPI2_SCK, P_SPI2_MISO, P_SPI2_MOSI, 0},
};
diff --git a/arch/blackfin/mach-bf538/include/mach/defBF539.h b/arch/blackfin/mach-bf538/include/mach/defBF539.h
index fe43062..7a8ac5f 100644
--- a/arch/blackfin/mach-bf538/include/mach/defBF539.h
+++ b/arch/blackfin/mach-bf538/include/mach/defBF539.h
@@ -32,6 +32,7 @@
/* System Interrupt Controller (0xFFC00100 - 0xFFC001FF) */
#define SWRST 0xFFC00100 /* Software Reset Register (16-bit) */
#define SYSCR 0xFFC00104 /* System Configuration registe */
+#define SIC_RVECT 0xFFC00108
#define SIC_IMASK0 0xFFC0010C /* Interrupt Mask Register */
#define SIC_IAR0 0xFFC00110 /* Interrupt Assignment Register 0 */
#define SIC_IAR1 0xFFC00114 /* Interrupt Assignment Register 1 */
@@ -1894,78 +1895,6 @@
#define PE14_P 0xE
#define PE15_P 0xF
-
-/* *********** SERIAL PERIPHERAL INTERFACE (SPI) MASKS **************** */
-/* SPIx_CTL Masks */
-#define TIMOD 0x0003 /* Transfer Initiate Mode */
-#define RDBR_CORE 0x0000 /* RDBR Read Initiates, IRQ When RDBR Full */
-#define TDBR_CORE 0x0001 /* TDBR Write Initiates, IRQ When TDBR Empty */
-#define RDBR_DMA 0x0002 /* DMA Read, DMA Until FIFO Empty */
-#define TDBR_DMA 0x0003 /* DMA Write, DMA Until FIFO Full */
-#define SZ 0x0004 /* Send Zero (When TDBR Empty, Send Zero/Last*) */
-#define GM 0x0008 /* Get More (When RDBR Full, Overwrite/Discard*) */
-#define PSSE 0x0010 /* Slave-Select Input Enable */
-#define EMISO 0x0020 /* Enable MISO As Output */
-#define SIZE 0x0100 /* Size of Words (16/8* Bits) */
-#define LSBF 0x0200 /* LSB First */
-#define CPHA 0x0400 /* Clock Phase */
-#define CPOL 0x0800 /* Clock Polarity */
-#define MSTR 0x1000 /* Master/Slave* */
-#define WOM 0x2000 /* Write Open Drain Master */
-#define SPE 0x4000 /* SPI Enable */
-
-/* SPIx_FLG Masks */
-#define FLS1 0x0002 /* Enables (=1) SPI_FLOUT1 as flag output for SPI Slave-select */
-#define FLS2 0x0004 /* Enables (=1) SPI_FLOUT2 as flag output for SPI Slave-select */
-#define FLS3 0x0008 /* Enables (=1) SPI_FLOUT3 as flag output for SPI Slave-select */
-#define FLS4 0x0010 /* Enables (=1) SPI_FLOUT4 as flag output for SPI Slave-select */
-#define FLS5 0x0020 /* Enables (=1) SPI_FLOUT5 as flag output for SPI Slave-select */
-#define FLS6 0x0040 /* Enables (=1) SPI_FLOUT6 as flag output for SPI Slave-select */
-#define FLS7 0x0080 /* Enables (=1) SPI_FLOUT7 as flag output for SPI Slave-select */
-
-#define FLG1 0x0200 /* Activates (=0) SPI_FLOUT1 as flag output for SPI Slave-select */
-#define FLG2 0x0400 /* Activates (=0) SPI_FLOUT2 as flag output for SPI Slave-select */
-#define FLG3 0x0800 /* Activates (=0) SPI_FLOUT3 as flag output for SPI Slave-select */
-#define FLG4 0x1000 /* Activates (=0) SPI_FLOUT4 as flag output for SPI Slave-select */
-#define FLG5 0x2000 /* Activates (=0) SPI_FLOUT5 as flag output for SPI Slave-select */
-#define FLG6 0x4000 /* Activates (=0) SPI_FLOUT6 as flag output for SPI Slave-select */
-#define FLG7 0x8000 /* Activates (=0) SPI_FLOUT7 as flag output for SPI Slave-select */
-
-/* SPIx_FLG Bit Positions */
-#define FLS1_P 0x0001 /* Enables (=1) SPI_FLOUT1 as flag output for SPI Slave-select */
-#define FLS2_P 0x0002 /* Enables (=1) SPI_FLOUT2 as flag output for SPI Slave-select */
-#define FLS3_P 0x0003 /* Enables (=1) SPI_FLOUT3 as flag output for SPI Slave-select */
-#define FLS4_P 0x0004 /* Enables (=1) SPI_FLOUT4 as flag output for SPI Slave-select */
-#define FLS5_P 0x0005 /* Enables (=1) SPI_FLOUT5 as flag output for SPI Slave-select */
-#define FLS6_P 0x0006 /* Enables (=1) SPI_FLOUT6 as flag output for SPI Slave-select */
-#define FLS7_P 0x0007 /* Enables (=1) SPI_FLOUT7 as flag output for SPI Slave-select */
-#define FLG1_P 0x0009 /* Activates (=0) SPI_FLOUT1 as flag output for SPI Slave-select */
-#define FLG2_P 0x000A /* Activates (=0) SPI_FLOUT2 as flag output for SPI Slave-select */
-#define FLG3_P 0x000B /* Activates (=0) SPI_FLOUT3 as flag output for SPI Slave-select */
-#define FLG4_P 0x000C /* Activates (=0) SPI_FLOUT4 as flag output for SPI Slave-select */
-#define FLG5_P 0x000D /* Activates (=0) SPI_FLOUT5 as flag output for SPI Slave-select */
-#define FLG6_P 0x000E /* Activates (=0) SPI_FLOUT6 as flag output for SPI Slave-select */
-#define FLG7_P 0x000F /* Activates (=0) SPI_FLOUT7 as flag output for SPI Slave-select */
-
-/* SPIx_STAT Masks */
-#define SPIF 0x0001 /* Set (=1) when SPI single-word transfer complete */
-#define MODF 0x0002 /* Set (=1) in a master device when some other device tries to become master */
-#define TXE 0x0004 /* Set (=1) when transmission occurs with no new data in SPI_TDBR */
-#define TXS 0x0008 /* SPI_TDBR Data Buffer Status (0=Empty, 1=Full) */
-#define RBSY 0x0010 /* Set (=1) when data is received with RDBR full */
-#define RXS 0x0020 /* SPI_RDBR Data Buffer Status (0=Empty, 1=Full) */
-#define TXCOL 0x0040 /* When set (=1), corrupt data may have been transmitted */
-
-/* SPIx_FLG Masks */
-#define FLG1E 0xFDFF /* Activates SPI_FLOUT1 */
-#define FLG2E 0xFBFF /* Activates SPI_FLOUT2 */
-#define FLG3E 0xF7FF /* Activates SPI_FLOUT3 */
-#define FLG4E 0xEFFF /* Activates SPI_FLOUT4 */
-#define FLG5E 0xDFFF /* Activates SPI_FLOUT5 */
-#define FLG6E 0xBFFF /* Activates SPI_FLOUT6 */
-#define FLG7E 0x7FFF /* Activates SPI_FLOUT7 */
-
-
/* ********************* ASYNCHRONOUS MEMORY CONTROLLER MASKS ************* */
/* EBIU_AMGCTL Masks */
#define AMCKEN 0x0001 /* Enable CLKOUT */
diff --git a/arch/blackfin/mach-bf548/boards/cm_bf548.c b/arch/blackfin/mach-bf548/boards/cm_bf548.c
index 0c38eec..f0c0eef 100644
--- a/arch/blackfin/mach-bf548/boards/cm_bf548.c
+++ b/arch/blackfin/mach-bf548/boards/cm_bf548.c
@@ -753,6 +753,44 @@
};
#endif
+#if defined(CONFIG_CAN_BFIN) || defined(CONFIG_CAN_BFIN_MODULE)
+unsigned short bfin_can_peripherals[] = {
+ P_CAN0_RX, P_CAN0_TX, 0
+};
+
+static struct resource bfin_can_resources[] = {
+ {
+ .start = 0xFFC02A00,
+ .end = 0xFFC02FFF,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_CAN0_RX,
+ .end = IRQ_CAN0_RX,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = IRQ_CAN0_TX,
+ .end = IRQ_CAN0_TX,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = IRQ_CAN0_ERROR,
+ .end = IRQ_CAN0_ERROR,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bfin_can_device = {
+ .name = "bfin_can",
+ .num_resources = ARRAY_SIZE(bfin_can_resources),
+ .resource = bfin_can_resources,
+ .dev = {
+ .platform_data = &bfin_can_peripherals, /* Passed to driver */
+ },
+};
+#endif
+
#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
static struct mtd_partition para_partitions[] = {
{
@@ -928,7 +966,7 @@
/* SPI controller data */
static struct bfin5xx_spi_master bf54x_spi_master_info0 = {
- .num_chipselect = 3,
+ .num_chipselect = 4,
.enable_dma = 1, /* master has the ability to do dma transfer */
.pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
};
@@ -944,7 +982,7 @@
};
static struct bfin5xx_spi_master bf54x_spi_master_info1 = {
- .num_chipselect = 3,
+ .num_chipselect = 4,
.enable_dma = 1, /* master has the ability to do dma transfer */
.pin_req = {P_SPI1_SCK, P_SPI1_MISO, P_SPI1_MOSI, 0},
};
@@ -1152,6 +1190,11 @@
#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
¶_flash_device,
#endif
+
+#if defined(CONFIG_CAN_BFIN) || defined(CONFIG_CAN_BFIN_MODULE)
+ &bfin_can_device,
+#endif
+
};
static int __init cm_bf548_init(void)
diff --git a/arch/blackfin/mach-bf548/boards/ezkit.c b/arch/blackfin/mach-bf548/boards/ezkit.c
index 56682a3..216e269 100644
--- a/arch/blackfin/mach-bf548/boards/ezkit.c
+++ b/arch/blackfin/mach-bf548/boards/ezkit.c
@@ -837,8 +837,12 @@
#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
static struct mtd_partition partition_info[] = {
{
- .name = "linux kernel(nand)",
+ .name = "bootloader(nand)",
.offset = 0,
+ .size = 0x80000,
+ }, {
+ .name = "linux kernel(nand)",
+ .offset = MTDPART_OFS_APPEND,
.size = 4 * 1024 * 1024,
},
{
@@ -901,7 +905,7 @@
static struct mtd_partition ezkit_partitions[] = {
{
.name = "bootloader(nor)",
- .size = 0x40000,
+ .size = 0x80000,
.offset = 0,
}, {
.name = "linux kernel(nor)",
@@ -943,7 +947,7 @@
static struct mtd_partition bfin_spi_flash_partitions[] = {
{
.name = "bootloader(spi)",
- .size = 0x00040000,
+ .size = 0x00080000,
.offset = 0,
.mask_flags = MTD_CAP_ROM
}, {
@@ -966,8 +970,8 @@
};
#endif
-#if defined(CONFIG_SND_BLACKFIN_AD183X) \
- || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
+ || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
@@ -1023,13 +1027,13 @@
.mode = SPI_MODE_3,
},
#endif
-#if defined(CONFIG_SND_BLACKFIN_AD183X) \
- || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
+ || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
{
- .modalias = "ad1836",
+ .modalias = "ad183x",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 1,
- .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+ .chip_select = 4,
.controller_data = &ad1836_spi_chip_info,
},
#endif
@@ -1107,7 +1111,7 @@
/* SPI controller data */
static struct bfin5xx_spi_master bf54x_spi_master_info0 = {
- .num_chipselect = 3,
+ .num_chipselect = 4,
.enable_dma = 1, /* master has the ability to do dma transfer */
.pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
};
@@ -1123,7 +1127,7 @@
};
static struct bfin5xx_spi_master bf54x_spi_master_info1 = {
- .num_chipselect = 3,
+ .num_chipselect = 4,
.enable_dma = 1, /* master has the ability to do dma transfer */
.pin_req = {P_SPI1_SCK, P_SPI1_MISO, P_SPI1_MOSI, 0},
};
@@ -1206,6 +1210,11 @@
.platform_data = (void *)&adxl34x_info,
},
#endif
+#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+ {
+ I2C_BOARD_INFO("ad5252", 0x2f),
+ },
+#endif
};
#endif
diff --git a/arch/blackfin/mach-bf548/dma.c b/arch/blackfin/mach-bf548/dma.c
index 039a6d9..888b9cc 100644
--- a/arch/blackfin/mach-bf548/dma.c
+++ b/arch/blackfin/mach-bf548/dma.c
@@ -63,6 +63,7 @@
break;
case CH_SPORT1_TX:
ret_irq = IRQ_SPORT1_TX;
+ break;
case CH_SPI0:
ret_irq = IRQ_SPI0;
break;
diff --git a/arch/blackfin/mach-bf548/include/mach/cdefBF54x_base.h b/arch/blackfin/mach-bf548/include/mach/cdefBF54x_base.h
index 0c16067d..deaf5d6 100644
--- a/arch/blackfin/mach-bf548/include/mach/cdefBF54x_base.h
+++ b/arch/blackfin/mach-bf548/include/mach/cdefBF54x_base.h
@@ -40,6 +40,8 @@
/* SIC Registers */
+#define bfin_read_SIC_RVECT() bfin_read32(SIC_RVECT)
+#define bfin_write_SIC_RVECT(val) bfin_write32(SIC_RVECT, val)
#define bfin_read_SIC_IMASK0() bfin_read32(SIC_IMASK0)
#define bfin_write_SIC_IMASK0(val) bfin_write32(SIC_IMASK0, val)
#define bfin_read_SIC_IMASK1() bfin_read32(SIC_IMASK1)
diff --git a/arch/blackfin/mach-bf548/include/mach/defBF54x_base.h b/arch/blackfin/mach-bf548/include/mach/defBF54x_base.h
index 7866197..78f9110 100644
--- a/arch/blackfin/mach-bf548/include/mach/defBF54x_base.h
+++ b/arch/blackfin/mach-bf548/include/mach/defBF54x_base.h
@@ -35,6 +35,7 @@
/* SIC Registers */
+#define SIC_RVECT 0xffc00108
#define SIC_IMASK0 0xffc0010c /* System Interrupt Mask Register 0 */
#define SIC_IMASK1 0xffc00110 /* System Interrupt Mask Register 1 */
#define SIC_IMASK2 0xffc00114 /* System Interrupt Mask Register 2 */
@@ -2061,56 +2062,6 @@
#define LOW_EVEN 0xff0000 /* Lower Limit for Even Bytes (Luma) */
#define HIGH_EVEN 0xff000000 /* Upper Limit for Even Bytes (Luma) */
-/* Bit masks for SPIx_BAUD */
-
-#define SPI_BAUD 0xffff /* Baud Rate */
-
-/* Bit masks for SPIx_CTL */
-
-#define SPE 0x4000 /* SPI Enable */
-#define WOM 0x2000 /* Write Open Drain Master */
-#define MSTR 0x1000 /* Master Mode */
-#define CPOL 0x800 /* Clock Polarity */
-#define CPHA 0x400 /* Clock Phase */
-#define LSBF 0x200 /* LSB First */
-#define SIZE 0x100 /* Size of Words */
-#define EMISO 0x20 /* Enable MISO Output */
-#define PSSE 0x10 /* Slave-Select Enable */
-#define GM 0x8 /* Get More Data */
-#define SZ 0x4 /* Send Zero */
-#define TIMOD 0x3 /* Transfer Initiation Mode */
-
-/* Bit masks for SPIx_FLG */
-
-#define FLS1 0x2 /* Slave Select Enable 1 */
-#define FLS2 0x4 /* Slave Select Enable 2 */
-#define FLS3 0x8 /* Slave Select Enable 3 */
-#define FLG1 0x200 /* Slave Select Value 1 */
-#define FLG2 0x400 /* Slave Select Value 2 */
-#define FLG3 0x800 /* Slave Select Value 3 */
-
-/* Bit masks for SPIx_STAT */
-
-#define TXCOL 0x40 /* Transmit Collision Error */
-#define RXS 0x20 /* RDBR Data Buffer Status */
-#define RBSY 0x10 /* Receive Error */
-#define TXS 0x8 /* TDBR Data Buffer Status */
-#define TXE 0x4 /* Transmission Error */
-#define MODF 0x2 /* Mode Fault Error */
-#define SPIF 0x1 /* SPI Finished */
-
-/* Bit masks for SPIx_TDBR */
-
-#define TDBR 0xffff /* Transmit Data Buffer */
-
-/* Bit masks for SPIx_RDBR */
-
-#define RDBR 0xffff /* Receive Data Buffer */
-
-/* Bit masks for SPIx_SHADOW */
-
-#define SHADOW 0xffff /* RDBR Shadow */
-
/* ************************************************ */
/* The TWI bit masks fields are from the ADSP-BF538 */
/* and they have not been verified as the final */
diff --git a/arch/blackfin/mach-bf561/boards/acvilon.c b/arch/blackfin/mach-bf561/boards/acvilon.c
index 35b6d12..0b1c20f 100644
--- a/arch/blackfin/mach-bf561/boards/acvilon.c
+++ b/arch/blackfin/mach-bf561/boards/acvilon.c
@@ -302,7 +302,7 @@
static struct resource bfin_plat_nand_resources = {
.start = 0x24000000,
.end = 0x24000000 + (1 << MAX(BFIN_NAND_PLAT_CLE, BFIN_NAND_PLAT_ALE)),
- .flags = IORESOURCE_IO,
+ .flags = IORESOURCE_MEM,
};
static struct platform_device bfin_async_nand_device = {
diff --git a/arch/blackfin/mach-bf561/boards/cm_bf561.c b/arch/blackfin/mach-bf561/boards/cm_bf561.c
index e127aed..087b6b0 100644
--- a/arch/blackfin/mach-bf561/boards/cm_bf561.c
+++ b/arch/blackfin/mach-bf561/boards/cm_bf561.c
@@ -72,7 +72,7 @@
};
#endif
-#if defined(CONFIG_SND_BLACKFIN_AD183X) || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
@@ -111,12 +111,12 @@
},
#endif
-#if defined(CONFIG_SND_BLACKFIN_AD183X) || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
{
- .modalias = "ad1836",
+ .modalias = "ad183x",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
- .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+ .chip_select = 4,
.controller_data = &ad1836_spi_chip_info,
},
#endif
@@ -278,7 +278,7 @@
}, {
.start = IRQ_PF47,
.end = IRQ_PF47,
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
},
};
diff --git a/arch/blackfin/mach-bf561/boards/ezkit.c b/arch/blackfin/mach-bf561/boards/ezkit.c
index 9b93e2f..ab7a487 100644
--- a/arch/blackfin/mach-bf561/boards/ezkit.c
+++ b/arch/blackfin/mach-bf561/boards/ezkit.c
@@ -14,6 +14,7 @@
#include <linux/spi/spi.h>
#include <linux/irq.h>
#include <linux/interrupt.h>
+#include <linux/delay.h>
#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
#include <asm/portmux.h>
@@ -74,7 +75,7 @@
}, {
.start = IRQ_PF8,
.end = IRQ_PF8,
- .flags = IORESOURCE_IRQ,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
},
};
@@ -274,8 +275,8 @@
};
#endif
-#if defined(CONFIG_SND_BLACKFIN_AD183X) \
- || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
+ || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
@@ -328,14 +329,16 @@
#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_SND_BLACKFIN_AD183X) \
- || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
+ || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
{
- .modalias = "ad1836",
+ .modalias = "ad183x",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
- .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+ .chip_select = 4,
+ .platform_data = "ad1836", /* only includes chip name for the moment */
.controller_data = &ad1836_spi_chip_info,
+ .mode = SPI_MODE_3,
},
#endif
#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
@@ -377,8 +380,8 @@
#include <linux/i2c-gpio.h>
static struct i2c_gpio_platform_data i2c_gpio_data = {
- .sda_pin = 1,
- .scl_pin = 0,
+ .sda_pin = GPIO_PF1,
+ .scl_pin = GPIO_PF0,
.sda_is_open_drain = 0,
.scl_is_open_drain = 0,
.udelay = 40,
@@ -420,6 +423,30 @@
},
};
+#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+static struct platform_device bfin_i2s = {
+ .name = "bfin-i2s",
+ .id = CONFIG_SND_BF5XX_SPORT_NUM,
+ /* TODO: add platform data here */
+};
+#endif
+
+#if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
+static struct platform_device bfin_tdm = {
+ .name = "bfin-tdm",
+ .id = CONFIG_SND_BF5XX_SPORT_NUM,
+ /* TODO: add platform data here */
+};
+#endif
+
+#if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+static struct platform_device bfin_ac97 = {
+ .name = "bfin-ac97",
+ .id = CONFIG_SND_BF5XX_SPORT_NUM,
+ /* TODO: add platform data here */
+};
+#endif
+
static struct platform_device *ezkit_devices[] __initdata = {
&bfin_dpmc,
@@ -467,6 +494,18 @@
#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
&ezkit_flash_device,
#endif
+
+#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+ &bfin_i2s,
+#endif
+
+#if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
+ &bfin_tdm,
+#endif
+
+#if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+ &bfin_ac97,
+#endif
};
static int __init ezkit_init(void)
@@ -484,6 +523,17 @@
SSYNC();
#endif
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+ bfin_write_FIO0_DIR(bfin_read_FIO0_DIR() | (1 << 15));
+ bfin_write_FIO0_FLAG_S(1 << 15);
+ SSYNC();
+ /*
+ * This initialization lasts for approximately 4500 MCLKs.
+ * MCLK = 12.288MHz
+ */
+ udelay(400);
+#endif
+
spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
return 0;
}
diff --git a/arch/blackfin/mach-bf561/coreb.c b/arch/blackfin/mach-bf561/coreb.c
index c6a4c8f..78ecb50 100644
--- a/arch/blackfin/mach-bf561/coreb.c
+++ b/arch/blackfin/mach-bf561/coreb.c
@@ -18,9 +18,9 @@
#include <linux/miscdevice.h>
#include <linux/module.h>
-#define CMD_COREB_START 2
-#define CMD_COREB_STOP 3
-#define CMD_COREB_RESET 4
+#define CMD_COREB_START _IO('b', 0)
+#define CMD_COREB_STOP _IO('b', 1)
+#define CMD_COREB_RESET _IO('b', 2)
static long
coreb_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
@@ -29,10 +29,10 @@
switch (cmd) {
case CMD_COREB_START:
- bfin_write_SICA_SYSCR(bfin_read_SICA_SYSCR() & ~0x0020);
+ bfin_write_SYSCR(bfin_read_SYSCR() & ~0x0020);
break;
case CMD_COREB_STOP:
- bfin_write_SICA_SYSCR(bfin_read_SICA_SYSCR() | 0x0020);
+ bfin_write_SYSCR(bfin_read_SYSCR() | 0x0020);
bfin_write_SICB_SYSCR(bfin_read_SICB_SYSCR() | 0x0080);
break;
case CMD_COREB_RESET:
@@ -74,3 +74,4 @@
MODULE_AUTHOR("Bas Vermeulen <bvermeul@blackstar.xs4all.nl>");
MODULE_DESCRIPTION("BF561 Core B Support");
+MODULE_LICENSE("GPL");
diff --git a/arch/blackfin/mach-bf561/include/mach/blackfin.h b/arch/blackfin/mach-bf561/include/mach/blackfin.h
index 67d6bdc..6c7dc58 100644
--- a/arch/blackfin/mach-bf561/include/mach/blackfin.h
+++ b/arch/blackfin/mach-bf561/include/mach/blackfin.h
@@ -24,29 +24,16 @@
#define bfin_read_FIO_INEN() bfin_read_FIO0_INEN()
#define bfin_write_FIO_INEN(val) bfin_write_FIO0_INEN(val)
-#define SIC_IWR0 SICA_IWR0
-#define SIC_IWR1 SICA_IWR1
-#define SIC_IAR0 SICA_IAR0
-#define bfin_write_SIC_IMASK0 bfin_write_SICA_IMASK0
-#define bfin_write_SIC_IMASK1 bfin_write_SICA_IMASK1
-#define bfin_write_SIC_IWR0 bfin_write_SICA_IWR0
-#define bfin_write_SIC_IWR1 bfin_write_SICA_IWR1
-
-#define bfin_read_SIC_IMASK0 bfin_read_SICA_IMASK0
-#define bfin_read_SIC_IMASK1 bfin_read_SICA_IMASK1
-#define bfin_read_SIC_IWR0 bfin_read_SICA_IWR0
-#define bfin_read_SIC_IWR1 bfin_read_SICA_IWR1
-#define bfin_read_SIC_ISR0 bfin_read_SICA_ISR0
-#define bfin_read_SIC_ISR1 bfin_read_SICA_ISR1
-
-#define bfin_read_SIC_IMASK(x) bfin_read32(SICA_IMASK0 + (x << 2))
-#define bfin_write_SIC_IMASK(x, val) bfin_write32((SICA_IMASK0 + (x << 2)), val)
-#define bfin_read_SICB_IMASK(x) bfin_read32(SICB_IMASK0 + (x << 2))
-#define bfin_write_SICB_IMASK(x, val) bfin_write32((SICB_IMASK0 + (x << 2)), val)
-#define bfin_read_SIC_ISR(x) bfin_read32(SICA_ISR0 + (x << 2))
-#define bfin_write_SIC_ISR(x, val) bfin_write32((SICA_ISR0 + (x << 2)), val)
-#define bfin_read_SICB_ISR(x) bfin_read32(SICB_ISR0 + (x << 2))
-#define bfin_write_SICB_ISR(x, val) bfin_write32((SICB_ISR0 + (x << 2)), val)
+/* Weird muxer funcs which pick SIC regs from IMASK base */
+#define __SIC_MUX(base, x) ((base) + ((x) << 2))
+#define bfin_read_SIC_IMASK(x) bfin_read32(__SIC_MUX(SIC_IMASK0, x))
+#define bfin_write_SIC_IMASK(x, val) bfin_write32(__SIC_MUX(SIC_IMASK0, x), val)
+#define bfin_read_SICB_IMASK(x) bfin_read32(__SIC_MUX(SICB_IMASK0, x))
+#define bfin_write_SICB_IMASK(x, val) bfin_write32(__SIC_MUX(SICB_IMASK0, x), val)
+#define bfin_read_SIC_ISR(x) bfin_read32(__SIC_MUX(SIC_ISR0, x))
+#define bfin_write_SIC_ISR(x, val) bfin_write32(__SIC_MUX(SIC_ISR0, x), val)
+#define bfin_read_SICB_ISR(x) bfin_read32(__SIC_MUX(SICB_ISR0, x))
+#define bfin_write_SICB_ISR(x, val) bfin_write32(__SIC_MUX(SICB_ISR0, x), val)
#define BFIN_UART_NR_PORTS 1
diff --git a/arch/blackfin/mach-bf561/include/mach/cdefBF561.h b/arch/blackfin/mach-bf561/include/mach/cdefBF561.h
index cc0416a..2bab991 100644
--- a/arch/blackfin/mach-bf561/include/mach/cdefBF561.h
+++ b/arch/blackfin/mach-bf561/include/mach/cdefBF561.h
@@ -30,49 +30,41 @@
#define bfin_write_PLL_LOCKCNT(val) bfin_write16(PLL_LOCKCNT,val)
#define bfin_read_CHIPID() bfin_read32(CHIPID)
-/* For MMR's that are reserved on Core B, set up defines to better integrate with other ports */
-#define bfin_read_SWRST() bfin_read_SICA_SWRST()
-#define bfin_write_SWRST(val) bfin_write_SICA_SWRST(val)
-#define bfin_read_SYSCR() bfin_read_SICA_SYSCR()
-#define bfin_write_SYSCR(val) bfin_write_SICA_SYSCR(val)
-
/* System Reset and Interrupt Controller registers for core A (0xFFC0 0100-0xFFC0 01FF) */
-#define bfin_read_SICA_SWRST() bfin_read16(SICA_SWRST)
-#define bfin_write_SICA_SWRST(val) bfin_write16(SICA_SWRST,val)
-#define bfin_read_SICA_SYSCR() bfin_read16(SICA_SYSCR)
-#define bfin_write_SICA_SYSCR(val) bfin_write16(SICA_SYSCR,val)
-#define bfin_read_SICA_RVECT() bfin_read16(SICA_RVECT)
-#define bfin_write_SICA_RVECT(val) bfin_write16(SICA_RVECT,val)
-#define bfin_read_SICA_IMASK() bfin_read32(SICA_IMASK)
-#define bfin_write_SICA_IMASK(val) bfin_write32(SICA_IMASK,val)
-#define bfin_read_SICA_IMASK0() bfin_read32(SICA_IMASK0)
-#define bfin_write_SICA_IMASK0(val) bfin_write32(SICA_IMASK0,val)
-#define bfin_read_SICA_IMASK1() bfin_read32(SICA_IMASK1)
-#define bfin_write_SICA_IMASK1(val) bfin_write32(SICA_IMASK1,val)
-#define bfin_read_SICA_IAR0() bfin_read32(SICA_IAR0)
-#define bfin_write_SICA_IAR0(val) bfin_write32(SICA_IAR0,val)
-#define bfin_read_SICA_IAR1() bfin_read32(SICA_IAR1)
-#define bfin_write_SICA_IAR1(val) bfin_write32(SICA_IAR1,val)
-#define bfin_read_SICA_IAR2() bfin_read32(SICA_IAR2)
-#define bfin_write_SICA_IAR2(val) bfin_write32(SICA_IAR2,val)
-#define bfin_read_SICA_IAR3() bfin_read32(SICA_IAR3)
-#define bfin_write_SICA_IAR3(val) bfin_write32(SICA_IAR3,val)
-#define bfin_read_SICA_IAR4() bfin_read32(SICA_IAR4)
-#define bfin_write_SICA_IAR4(val) bfin_write32(SICA_IAR4,val)
-#define bfin_read_SICA_IAR5() bfin_read32(SICA_IAR5)
-#define bfin_write_SICA_IAR5(val) bfin_write32(SICA_IAR5,val)
-#define bfin_read_SICA_IAR6() bfin_read32(SICA_IAR6)
-#define bfin_write_SICA_IAR6(val) bfin_write32(SICA_IAR6,val)
-#define bfin_read_SICA_IAR7() bfin_read32(SICA_IAR7)
-#define bfin_write_SICA_IAR7(val) bfin_write32(SICA_IAR7,val)
-#define bfin_read_SICA_ISR0() bfin_read32(SICA_ISR0)
-#define bfin_write_SICA_ISR0(val) bfin_write32(SICA_ISR0,val)
-#define bfin_read_SICA_ISR1() bfin_read32(SICA_ISR1)
-#define bfin_write_SICA_ISR1(val) bfin_write32(SICA_ISR1,val)
-#define bfin_read_SICA_IWR0() bfin_read32(SICA_IWR0)
-#define bfin_write_SICA_IWR0(val) bfin_write32(SICA_IWR0,val)
-#define bfin_read_SICA_IWR1() bfin_read32(SICA_IWR1)
-#define bfin_write_SICA_IWR1(val) bfin_write32(SICA_IWR1,val)
+#define bfin_read_SWRST() bfin_read16(SWRST)
+#define bfin_write_SWRST(val) bfin_write16(SWRST,val)
+#define bfin_read_SYSCR() bfin_read16(SYSCR)
+#define bfin_write_SYSCR(val) bfin_write16(SYSCR,val)
+#define bfin_read_SIC_RVECT() bfin_read16(SIC_RVECT)
+#define bfin_write_SIC_RVECT(val) bfin_write16(SIC_RVECT,val)
+#define bfin_read_SIC_IMASK0() bfin_read32(SIC_IMASK0)
+#define bfin_write_SIC_IMASK0(val) bfin_write32(SIC_IMASK0,val)
+#define bfin_read_SIC_IMASK1() bfin_read32(SIC_IMASK1)
+#define bfin_write_SIC_IMASK1(val) bfin_write32(SIC_IMASK1,val)
+#define bfin_read_SIC_IAR0() bfin_read32(SIC_IAR0)
+#define bfin_write_SIC_IAR0(val) bfin_write32(SIC_IAR0,val)
+#define bfin_read_SIC_IAR1() bfin_read32(SIC_IAR1)
+#define bfin_write_SIC_IAR1(val) bfin_write32(SIC_IAR1,val)
+#define bfin_read_SIC_IAR2() bfin_read32(SIC_IAR2)
+#define bfin_write_SIC_IAR2(val) bfin_write32(SIC_IAR2,val)
+#define bfin_read_SIC_IAR3() bfin_read32(SIC_IAR3)
+#define bfin_write_SIC_IAR3(val) bfin_write32(SIC_IAR3,val)
+#define bfin_read_SIC_IAR4() bfin_read32(SIC_IAR4)
+#define bfin_write_SIC_IAR4(val) bfin_write32(SIC_IAR4,val)
+#define bfin_read_SIC_IAR5() bfin_read32(SIC_IAR5)
+#define bfin_write_SIC_IAR5(val) bfin_write32(SIC_IAR5,val)
+#define bfin_read_SIC_IAR6() bfin_read32(SIC_IAR6)
+#define bfin_write_SIC_IAR6(val) bfin_write32(SIC_IAR6,val)
+#define bfin_read_SIC_IAR7() bfin_read32(SIC_IAR7)
+#define bfin_write_SIC_IAR7(val) bfin_write32(SIC_IAR7,val)
+#define bfin_read_SIC_ISR0() bfin_read32(SIC_ISR0)
+#define bfin_write_SIC_ISR0(val) bfin_write32(SIC_ISR0,val)
+#define bfin_read_SIC_ISR1() bfin_read32(SIC_ISR1)
+#define bfin_write_SIC_ISR1(val) bfin_write32(SIC_ISR1,val)
+#define bfin_read_SIC_IWR0() bfin_read32(SIC_IWR0)
+#define bfin_write_SIC_IWR0(val) bfin_write32(SIC_IWR0,val)
+#define bfin_read_SIC_IWR1() bfin_read32(SIC_IWR1)
+#define bfin_write_SIC_IWR1(val) bfin_write32(SIC_IWR1,val)
/* System Reset and Interrupt Controller registers for Core B (0xFFC0 1100-0xFFC0 11FF) */
#define bfin_read_SICB_SWRST() bfin_read16(SICB_SWRST)
diff --git a/arch/blackfin/mach-bf561/include/mach/defBF561.h b/arch/blackfin/mach-bf561/include/mach/defBF561.h
index 2674f00..79e048d 100644
--- a/arch/blackfin/mach-bf561/include/mach/defBF561.h
+++ b/arch/blackfin/mach-bf561/include/mach/defBF561.h
@@ -28,32 +28,29 @@
#define CHIPID 0xFFC00014 /* Chip ID Register */
/* For MMR's that are reserved on Core B, set up defines to better integrate with other ports */
-#define SWRST SICA_SWRST
-#define SYSCR SICA_SYSCR
#define DOUBLE_FAULT (DOUBLE_FAULT_B|DOUBLE_FAULT_A)
#define RESET_DOUBLE (SWRST_DBL_FAULT_B|SWRST_DBL_FAULT_A)
#define RESET_WDOG (SWRST_WDT_B|SWRST_WDT_A)
#define RESET_SOFTWARE (SWRST_OCCURRED)
/* System Reset and Interrupt Controller registers for core A (0xFFC0 0100-0xFFC0 01FF) */
-#define SICA_SWRST 0xFFC00100 /* Software Reset register */
-#define SICA_SYSCR 0xFFC00104 /* System Reset Configuration register */
-#define SICA_RVECT 0xFFC00108 /* SIC Reset Vector Address Register */
-#define SICA_IMASK 0xFFC0010C /* SIC Interrupt Mask register 0 - hack to fix old tests */
-#define SICA_IMASK0 0xFFC0010C /* SIC Interrupt Mask register 0 */
-#define SICA_IMASK1 0xFFC00110 /* SIC Interrupt Mask register 1 */
-#define SICA_IAR0 0xFFC00124 /* SIC Interrupt Assignment Register 0 */
-#define SICA_IAR1 0xFFC00128 /* SIC Interrupt Assignment Register 1 */
-#define SICA_IAR2 0xFFC0012C /* SIC Interrupt Assignment Register 2 */
-#define SICA_IAR3 0xFFC00130 /* SIC Interrupt Assignment Register 3 */
-#define SICA_IAR4 0xFFC00134 /* SIC Interrupt Assignment Register 4 */
-#define SICA_IAR5 0xFFC00138 /* SIC Interrupt Assignment Register 5 */
-#define SICA_IAR6 0xFFC0013C /* SIC Interrupt Assignment Register 6 */
-#define SICA_IAR7 0xFFC00140 /* SIC Interrupt Assignment Register 7 */
-#define SICA_ISR0 0xFFC00114 /* SIC Interrupt Status register 0 */
-#define SICA_ISR1 0xFFC00118 /* SIC Interrupt Status register 1 */
-#define SICA_IWR0 0xFFC0011C /* SIC Interrupt Wakeup-Enable register 0 */
-#define SICA_IWR1 0xFFC00120 /* SIC Interrupt Wakeup-Enable register 1 */
+#define SWRST 0xFFC00100 /* Software Reset register */
+#define SYSCR 0xFFC00104 /* System Reset Configuration register */
+#define SIC_RVECT 0xFFC00108 /* SIC Reset Vector Address Register */
+#define SIC_IMASK0 0xFFC0010C /* SIC Interrupt Mask register 0 */
+#define SIC_IMASK1 0xFFC00110 /* SIC Interrupt Mask register 1 */
+#define SIC_IAR0 0xFFC00124 /* SIC Interrupt Assignment Register 0 */
+#define SIC_IAR1 0xFFC00128 /* SIC Interrupt Assignment Register 1 */
+#define SIC_IAR2 0xFFC0012C /* SIC Interrupt Assignment Register 2 */
+#define SIC_IAR3 0xFFC00130 /* SIC Interrupt Assignment Register 3 */
+#define SIC_IAR4 0xFFC00134 /* SIC Interrupt Assignment Register 4 */
+#define SIC_IAR5 0xFFC00138 /* SIC Interrupt Assignment Register 5 */
+#define SIC_IAR6 0xFFC0013C /* SIC Interrupt Assignment Register 6 */
+#define SIC_IAR7 0xFFC00140 /* SIC Interrupt Assignment Register 7 */
+#define SIC_ISR0 0xFFC00114 /* SIC Interrupt Status register 0 */
+#define SIC_ISR1 0xFFC00118 /* SIC Interrupt Status register 1 */
+#define SIC_IWR0 0xFFC0011C /* SIC Interrupt Wakeup-Enable register 0 */
+#define SIC_IWR1 0xFFC00120 /* SIC Interrupt Wakeup-Enable register 1 */
/* System Reset and Interrupt Controller registers for Core B (0xFFC0 1100-0xFFC0 11FF) */
#define SICB_SWRST 0xFFC01100 /* reserved */
@@ -1271,63 +1268,6 @@
#define PF14_P 14
#define PF15_P 15
-/* *********** SERIAL PERIPHERAL INTERFACE (SPI) MASKS **************** */
-
-/* SPI_CTL Masks */
-#define TIMOD 0x00000003 /* Transfer initiation mode and interrupt generation */
-#define SZ 0x00000004 /* Send Zero (=0) or last (=1) word when TDBR empty. */
-#define GM 0x00000008 /* When RDBR full, get more (=1) data or discard (=0) incoming Data */
-#define PSSE 0x00000010 /* Enable (=1) Slave-Select input for Master. */
-#define EMISO 0x00000020 /* Enable (=1) MISO pin as an output. */
-#define SIZE 0x00000100 /* Word length (0 => 8 bits, 1 => 16 bits) */
-#define LSBF 0x00000200 /* Data format (0 => MSB sent/received first 1 => LSB sent/received first) */
-#define CPHA 0x00000400 /* Clock phase (0 => SPICLK starts toggling in middle of xfer, 1 => SPICLK toggles at the beginning of xfer. */
-#define CPOL 0x00000800 /* Clock polarity (0 => active-high, 1 => active-low) */
-#define MSTR 0x00001000 /* Configures SPI as master (=1) or slave (=0) */
-#define WOM 0x00002000 /* Open drain (=1) data output enable (for MOSI and MISO) */
-#define SPE 0x00004000 /* SPI module enable (=1), disable (=0) */
-
-/* SPI_FLG Masks */
-#define FLS1 0x00000002 /* Enables (=1) SPI_FLOUT1 as flag output for SPI Slave-select */
-#define FLS2 0x00000004 /* Enables (=1) SPI_FLOUT2 as flag output for SPI Slave-select */
-#define FLS3 0x00000008 /* Enables (=1) SPI_FLOUT3 as flag output for SPI Slave-select */
-#define FLS4 0x00000010 /* Enables (=1) SPI_FLOUT4 as flag output for SPI Slave-select */
-#define FLS5 0x00000020 /* Enables (=1) SPI_FLOUT5 as flag output for SPI Slave-select */
-#define FLS6 0x00000040 /* Enables (=1) SPI_FLOUT6 as flag output for SPI Slave-select */
-#define FLS7 0x00000080 /* Enables (=1) SPI_FLOUT7 as flag output for SPI Slave-select */
-#define FLG1 0x00000200 /* Activates (=0) SPI_FLOUT1 as flag output for SPI Slave-select */
-#define FLG2 0x00000400 /* Activates (=0) SPI_FLOUT2 as flag output for SPI Slave-select */
-#define FLG3 0x00000800 /* Activates (=0) SPI_FLOUT3 as flag output for SPI Slave-select */
-#define FLG4 0x00001000 /* Activates (=0) SPI_FLOUT4 as flag output for SPI Slave-select */
-#define FLG5 0x00002000 /* Activates (=0) SPI_FLOUT5 as flag output for SPI Slave-select */
-#define FLG6 0x00004000 /* Activates (=0) SPI_FLOUT6 as flag output for SPI Slave-select */
-#define FLG7 0x00008000 /* Activates (=0) SPI_FLOUT7 as flag output for SPI Slave-select */
-
-/* SPI_FLG Bit Positions */
-#define FLS1_P 0x00000001 /* Enables (=1) SPI_FLOUT1 as flag output for SPI Slave-select */
-#define FLS2_P 0x00000002 /* Enables (=1) SPI_FLOUT2 as flag output for SPI Slave-select */
-#define FLS3_P 0x00000003 /* Enables (=1) SPI_FLOUT3 as flag output for SPI Slave-select */
-#define FLS4_P 0x00000004 /* Enables (=1) SPI_FLOUT4 as flag output for SPI Slave-select */
-#define FLS5_P 0x00000005 /* Enables (=1) SPI_FLOUT5 as flag output for SPI Slave-select */
-#define FLS6_P 0x00000006 /* Enables (=1) SPI_FLOUT6 as flag output for SPI Slave-select */
-#define FLS7_P 0x00000007 /* Enables (=1) SPI_FLOUT7 as flag output for SPI Slave-select */
-#define FLG1_P 0x00000009 /* Activates (=0) SPI_FLOUT1 as flag output for SPI Slave-select */
-#define FLG2_P 0x0000000A /* Activates (=0) SPI_FLOUT2 as flag output for SPI Slave-select */
-#define FLG3_P 0x0000000B /* Activates (=0) SPI_FLOUT3 as flag output for SPI Slave-select */
-#define FLG4_P 0x0000000C /* Activates (=0) SPI_FLOUT4 as flag output for SPI Slave-select */
-#define FLG5_P 0x0000000D /* Activates (=0) SPI_FLOUT5 as flag output for SPI Slave-select */
-#define FLG6_P 0x0000000E /* Activates (=0) SPI_FLOUT6 as flag output for SPI Slave-select */
-#define FLG7_P 0x0000000F /* Activates (=0) SPI_FLOUT7 as flag output for SPI Slave-select */
-
-/* SPI_STAT Masks */
-#define SPIF 0x00000001 /* Set (=1) when SPI single-word transfer complete */
-#define MODF 0x00000002 /* Set (=1) in a master device when some other device tries to become master */
-#define TXE 0x00000004 /* Set (=1) when transmission occurs with no new data in SPI_TDBR */
-#define TXS 0x00000008 /* SPI_TDBR Data Buffer Status (0=Empty, 1=Full) */
-#define RBSY 0x00000010 /* Set (=1) when data is received with RDBR full */
-#define RXS 0x00000020 /* SPI_RDBR Data Buffer Status (0=Empty, 1=Full) */
-#define TXCOL 0x00000040 /* When set (=1), corrupt data may have been transmitted */
-
/* ********************* ASYNCHRONOUS MEMORY CONTROLLER MASKS ************* */
/* AMGCTL Masks */
diff --git a/arch/blackfin/mach-bf561/ints-priority.c b/arch/blackfin/mach-bf561/ints-priority.c
index b442417..7ee9262 100644
--- a/arch/blackfin/mach-bf561/ints-priority.c
+++ b/arch/blackfin/mach-bf561/ints-priority.c
@@ -13,7 +13,7 @@
void __init program_IAR(void)
{
/* Program the IAR0 Register with the configured priority */
- bfin_write_SICA_IAR0(((CONFIG_IRQ_PLL_WAKEUP - 7) << IRQ_PLL_WAKEUP_POS) |
+ bfin_write_SIC_IAR0(((CONFIG_IRQ_PLL_WAKEUP - 7) << IRQ_PLL_WAKEUP_POS) |
((CONFIG_IRQ_DMA1_ERROR - 7) << IRQ_DMA1_ERROR_POS) |
((CONFIG_IRQ_DMA2_ERROR - 7) << IRQ_DMA2_ERROR_POS) |
((CONFIG_IRQ_IMDMA_ERROR - 7) << IRQ_IMDMA_ERROR_POS) |
@@ -22,7 +22,7 @@
((CONFIG_IRQ_SPORT0_ERROR - 7) << IRQ_SPORT0_ERROR_POS) |
((CONFIG_IRQ_SPORT1_ERROR - 7) << IRQ_SPORT1_ERROR_POS));
- bfin_write_SICA_IAR1(((CONFIG_IRQ_SPI_ERROR - 7) << IRQ_SPI_ERROR_POS) |
+ bfin_write_SIC_IAR1(((CONFIG_IRQ_SPI_ERROR - 7) << IRQ_SPI_ERROR_POS) |
((CONFIG_IRQ_UART_ERROR - 7) << IRQ_UART_ERROR_POS) |
((CONFIG_IRQ_RESERVED_ERROR - 7) << IRQ_RESERVED_ERROR_POS) |
((CONFIG_IRQ_DMA1_0 - 7) << IRQ_DMA1_0_POS) |
@@ -31,7 +31,7 @@
((CONFIG_IRQ_DMA1_3 - 7) << IRQ_DMA1_3_POS) |
((CONFIG_IRQ_DMA1_4 - 7) << IRQ_DMA1_4_POS));
- bfin_write_SICA_IAR2(((CONFIG_IRQ_DMA1_5 - 7) << IRQ_DMA1_5_POS) |
+ bfin_write_SIC_IAR2(((CONFIG_IRQ_DMA1_5 - 7) << IRQ_DMA1_5_POS) |
((CONFIG_IRQ_DMA1_6 - 7) << IRQ_DMA1_6_POS) |
((CONFIG_IRQ_DMA1_7 - 7) << IRQ_DMA1_7_POS) |
((CONFIG_IRQ_DMA1_8 - 7) << IRQ_DMA1_8_POS) |
@@ -40,7 +40,7 @@
((CONFIG_IRQ_DMA1_11 - 7) << IRQ_DMA1_11_POS) |
((CONFIG_IRQ_DMA2_0 - 7) << IRQ_DMA2_0_POS));
- bfin_write_SICA_IAR3(((CONFIG_IRQ_DMA2_1 - 7) << IRQ_DMA2_1_POS) |
+ bfin_write_SIC_IAR3(((CONFIG_IRQ_DMA2_1 - 7) << IRQ_DMA2_1_POS) |
((CONFIG_IRQ_DMA2_2 - 7) << IRQ_DMA2_2_POS) |
((CONFIG_IRQ_DMA2_3 - 7) << IRQ_DMA2_3_POS) |
((CONFIG_IRQ_DMA2_4 - 7) << IRQ_DMA2_4_POS) |
@@ -49,7 +49,7 @@
((CONFIG_IRQ_DMA2_7 - 7) << IRQ_DMA2_7_POS) |
((CONFIG_IRQ_DMA2_8 - 7) << IRQ_DMA2_8_POS));
- bfin_write_SICA_IAR4(((CONFIG_IRQ_DMA2_9 - 7) << IRQ_DMA2_9_POS) |
+ bfin_write_SIC_IAR4(((CONFIG_IRQ_DMA2_9 - 7) << IRQ_DMA2_9_POS) |
((CONFIG_IRQ_DMA2_10 - 7) << IRQ_DMA2_10_POS) |
((CONFIG_IRQ_DMA2_11 - 7) << IRQ_DMA2_11_POS) |
((CONFIG_IRQ_TIMER0 - 7) << IRQ_TIMER0_POS) |
@@ -58,7 +58,7 @@
((CONFIG_IRQ_TIMER3 - 7) << IRQ_TIMER3_POS) |
((CONFIG_IRQ_TIMER4 - 7) << IRQ_TIMER4_POS));
- bfin_write_SICA_IAR5(((CONFIG_IRQ_TIMER5 - 7) << IRQ_TIMER5_POS) |
+ bfin_write_SIC_IAR5(((CONFIG_IRQ_TIMER5 - 7) << IRQ_TIMER5_POS) |
((CONFIG_IRQ_TIMER6 - 7) << IRQ_TIMER6_POS) |
((CONFIG_IRQ_TIMER7 - 7) << IRQ_TIMER7_POS) |
((CONFIG_IRQ_TIMER8 - 7) << IRQ_TIMER8_POS) |
@@ -67,7 +67,7 @@
((CONFIG_IRQ_TIMER11 - 7) << IRQ_TIMER11_POS) |
((CONFIG_IRQ_PROG0_INTA - 7) << IRQ_PROG0_INTA_POS));
- bfin_write_SICA_IAR6(((CONFIG_IRQ_PROG0_INTB - 7) << IRQ_PROG0_INTB_POS) |
+ bfin_write_SIC_IAR6(((CONFIG_IRQ_PROG0_INTB - 7) << IRQ_PROG0_INTB_POS) |
((CONFIG_IRQ_PROG1_INTA - 7) << IRQ_PROG1_INTA_POS) |
((CONFIG_IRQ_PROG1_INTB - 7) << IRQ_PROG1_INTB_POS) |
((CONFIG_IRQ_PROG2_INTA - 7) << IRQ_PROG2_INTA_POS) |
@@ -76,7 +76,7 @@
((CONFIG_IRQ_DMA1_WRRD1 - 7) << IRQ_DMA1_WRRD1_POS) |
((CONFIG_IRQ_DMA2_WRRD0 - 7) << IRQ_DMA2_WRRD0_POS));
- bfin_write_SICA_IAR7(((CONFIG_IRQ_DMA2_WRRD1 - 7) << IRQ_DMA2_WRRD1_POS) |
+ bfin_write_SIC_IAR7(((CONFIG_IRQ_DMA2_WRRD1 - 7) << IRQ_DMA2_WRRD1_POS) |
((CONFIG_IRQ_IMDMA_WRRD0 - 7) << IRQ_IMDMA_WRRD0_POS) |
((CONFIG_IRQ_IMDMA_WRRD1 - 7) << IRQ_IMDMA_WRRD1_POS) |
((CONFIG_IRQ_WDTIMER - 7) << IRQ_WDTIMER_POS) |
diff --git a/arch/blackfin/mach-bf561/smp.c b/arch/blackfin/mach-bf561/smp.c
index 3b9a4bf..f540ed1 100644
--- a/arch/blackfin/mach-bf561/smp.c
+++ b/arch/blackfin/mach-bf561/smp.c
@@ -52,19 +52,19 @@
void __cpuinit platform_secondary_init(unsigned int cpu)
{
/* Clone setup for peripheral interrupt sources from CoreA. */
- bfin_write_SICB_IMASK0(bfin_read_SICA_IMASK0());
- bfin_write_SICB_IMASK1(bfin_read_SICA_IMASK1());
+ bfin_write_SICB_IMASK0(bfin_read_SIC_IMASK0());
+ bfin_write_SICB_IMASK1(bfin_read_SIC_IMASK1());
SSYNC();
/* Clone setup for IARs from CoreA. */
- bfin_write_SICB_IAR0(bfin_read_SICA_IAR0());
- bfin_write_SICB_IAR1(bfin_read_SICA_IAR1());
- bfin_write_SICB_IAR2(bfin_read_SICA_IAR2());
- bfin_write_SICB_IAR3(bfin_read_SICA_IAR3());
- bfin_write_SICB_IAR4(bfin_read_SICA_IAR4());
- bfin_write_SICB_IAR5(bfin_read_SICA_IAR5());
- bfin_write_SICB_IAR6(bfin_read_SICA_IAR6());
- bfin_write_SICB_IAR7(bfin_read_SICA_IAR7());
+ bfin_write_SICB_IAR0(bfin_read_SIC_IAR0());
+ bfin_write_SICB_IAR1(bfin_read_SIC_IAR1());
+ bfin_write_SICB_IAR2(bfin_read_SIC_IAR2());
+ bfin_write_SICB_IAR3(bfin_read_SIC_IAR3());
+ bfin_write_SICB_IAR4(bfin_read_SIC_IAR4());
+ bfin_write_SICB_IAR5(bfin_read_SIC_IAR5());
+ bfin_write_SICB_IAR6(bfin_read_SIC_IAR6());
+ bfin_write_SICB_IAR7(bfin_read_SIC_IAR7());
bfin_write_SICB_IWR0(IWR_DISABLE_ALL);
bfin_write_SICB_IWR1(IWR_DISABLE_ALL);
SSYNC();
@@ -86,12 +86,12 @@
spin_lock(&boot_lock);
- if ((bfin_read_SICA_SYSCR() & COREB_SRAM_INIT) == 0) {
+ if ((bfin_read_SIC_SYSCR() & COREB_SRAM_INIT) == 0) {
/* CoreB already running, sending ipi to wakeup it */
platform_send_ipi_cpu(cpu, IRQ_SUPPLE_0);
} else {
/* Kick CoreB, which should start execution from CORE_SRAM_BASE. */
- bfin_write_SICA_SYSCR(bfin_read_SICA_SYSCR() & ~COREB_SRAM_INIT);
+ bfin_write_SIC_SYSCR(bfin_read_SIC_SYSCR() & ~COREB_SRAM_INIT);
SSYNC();
}
diff --git a/arch/blackfin/mach-common/dpmc_modes.S b/arch/blackfin/mach-common/dpmc_modes.S
index 5969d86..9cfdd49 100644
--- a/arch/blackfin/mach-common/dpmc_modes.S
+++ b/arch/blackfin/mach-common/dpmc_modes.S
@@ -292,13 +292,7 @@
#ifdef SIC_IMASK
PM_SYS_PUSH(SIC_IMASK)
#endif
-#ifdef SICA_IMASK0
- PM_SYS_PUSH(SICA_IMASK0)
-#endif
-#ifdef SICA_IMASK1
- PM_SYS_PUSH(SICA_IMASK1)
-#endif
-#ifdef SIC_IAR2
+#ifdef SIC_IAR0
PM_SYS_PUSH(SIC_IAR0)
PM_SYS_PUSH(SIC_IAR1)
PM_SYS_PUSH(SIC_IAR2)
@@ -321,17 +315,6 @@
PM_SYS_PUSH(SIC_IAR11)
#endif
-#ifdef SICA_IAR0
- PM_SYS_PUSH(SICA_IAR0)
- PM_SYS_PUSH(SICA_IAR1)
- PM_SYS_PUSH(SICA_IAR2)
- PM_SYS_PUSH(SICA_IAR3)
- PM_SYS_PUSH(SICA_IAR4)
- PM_SYS_PUSH(SICA_IAR5)
- PM_SYS_PUSH(SICA_IAR6)
- PM_SYS_PUSH(SICA_IAR7)
-#endif
-
#ifdef SIC_IWR
PM_SYS_PUSH(SIC_IWR)
#endif
@@ -344,12 +327,6 @@
#ifdef SIC_IWR2
PM_SYS_PUSH(SIC_IWR2)
#endif
-#ifdef SICA_IWR0
- PM_SYS_PUSH(SICA_IWR0)
-#endif
-#ifdef SICA_IWR1
- PM_SYS_PUSH(SICA_IWR1)
-#endif
#ifdef PINT0_ASSIGN
PM_SYS_PUSH(PINT0_MASK_SET)
@@ -750,12 +727,6 @@
PM_SYS_POP(PINT0_MASK_SET)
#endif
-#ifdef SICA_IWR1
- PM_SYS_POP(SICA_IWR1)
-#endif
-#ifdef SICA_IWR0
- PM_SYS_POP(SICA_IWR0)
-#endif
#ifdef SIC_IWR2
PM_SYS_POP(SIC_IWR2)
#endif
@@ -769,17 +740,6 @@
PM_SYS_POP(SIC_IWR)
#endif
-#ifdef SICA_IAR0
- PM_SYS_POP(SICA_IAR7)
- PM_SYS_POP(SICA_IAR6)
- PM_SYS_POP(SICA_IAR5)
- PM_SYS_POP(SICA_IAR4)
- PM_SYS_POP(SICA_IAR3)
- PM_SYS_POP(SICA_IAR2)
- PM_SYS_POP(SICA_IAR1)
- PM_SYS_POP(SICA_IAR0)
-#endif
-
#ifdef SIC_IAR8
PM_SYS_POP(SIC_IAR11)
PM_SYS_POP(SIC_IAR10)
@@ -797,17 +757,11 @@
#ifdef SIC_IAR3
PM_SYS_POP(SIC_IAR3)
#endif
-#ifdef SIC_IAR2
+#ifdef SIC_IAR0
PM_SYS_POP(SIC_IAR2)
PM_SYS_POP(SIC_IAR1)
PM_SYS_POP(SIC_IAR0)
#endif
-#ifdef SICA_IMASK1
- PM_SYS_POP(SICA_IMASK1)
-#endif
-#ifdef SICA_IMASK0
- PM_SYS_POP(SICA_IMASK0)
-#endif
#ifdef SIC_IMASK
PM_SYS_POP(SIC_IMASK)
#endif
diff --git a/arch/blackfin/mach-common/entry.S b/arch/blackfin/mach-common/entry.S
index af1bffa..2ca915e 100644
--- a/arch/blackfin/mach-common/entry.S
+++ b/arch/blackfin/mach-common/entry.S
@@ -889,6 +889,66 @@
rts;
ENDPROC(_ret_from_exception)
+#if defined(CONFIG_PREEMPT)
+
+ENTRY(_up_to_irq14)
+#if ANOMALY_05000281 || ANOMALY_05000461
+ r0.l = lo(SAFE_USER_INSTRUCTION);
+ r0.h = hi(SAFE_USER_INSTRUCTION);
+ reti = r0;
+#endif
+
+#ifdef CONFIG_DEBUG_HWERR
+ /* enable irq14 & hwerr interrupt, until we transition to _evt_evt14 */
+ r0 = (EVT_IVG14 | EVT_IVHW | EVT_IRPTEN | EVT_EVX | EVT_NMI | EVT_RST | EVT_EMU);
+#else
+ /* Only enable irq14 interrupt, until we transition to _evt_evt14 */
+ r0 = (EVT_IVG14 | EVT_IRPTEN | EVT_EVX | EVT_NMI | EVT_RST | EVT_EMU);
+#endif
+ sti r0;
+
+ p0.l = lo(EVT14);
+ p0.h = hi(EVT14);
+ p1.l = _evt_up_evt14;
+ p1.h = _evt_up_evt14;
+ [p0] = p1;
+ csync;
+
+ raise 14;
+1:
+ jump 1b;
+ENDPROC(_up_to_irq14)
+
+ENTRY(_evt_up_evt14)
+#ifdef CONFIG_DEBUG_HWERR
+ r0 = (EVT_IVHW | EVT_IRPTEN | EVT_EVX | EVT_NMI | EVT_RST | EVT_EMU);
+ sti r0;
+#else
+ cli r0;
+#endif
+#ifdef CONFIG_TRACE_IRQFLAGS
+ [--sp] = rets;
+ sp += -12;
+ call _trace_hardirqs_off;
+ sp += 12;
+ rets = [sp++];
+#endif
+ [--sp] = RETI;
+ SP += 4;
+
+ /* restore normal evt14 */
+ p0.l = lo(EVT14);
+ p0.h = hi(EVT14);
+ p1.l = _evt_evt14;
+ p1.h = _evt_evt14;
+ [p0] = p1;
+ csync;
+
+ rts;
+ENDPROC(_evt_up_evt14)
+
+#endif
+
#ifdef CONFIG_IPIPE
_resume_kernel_from_int:
@@ -902,8 +962,54 @@
( r7:4, p5:3 ) = [sp++];
rets = [sp++];
rts
+#elif defined(CONFIG_PREEMPT)
+
+_resume_kernel_from_int:
+ /* check preempt_count */
+ r7 = sp;
+ r4.l = lo(ALIGN_PAGE_MASK);
+ r4.h = hi(ALIGN_PAGE_MASK);
+ r7 = r7 & r4;
+ p5 = r7;
+ r7 = [p5 + TI_PREEMPT];
+ cc = r7 == 0x0;
+ if !cc jump .Lreturn_to_kernel;
+.Lneed_schedule:
+ r7 = [p5 + TI_FLAGS];
+ r4.l = lo(_TIF_WORK_MASK);
+ r4.h = hi(_TIF_WORK_MASK);
+ r7 = r7 & r4;
+ cc = BITTST(r7, TIF_NEED_RESCHED);
+ if !cc jump .Lreturn_to_kernel;
+ /*
+ * let schedule done at level 15, otherwise sheduled process will run
+ * at high level and block low level interrupt
+ */
+ r6 = reti; /* save reti */
+ r5.l = .Lkernel_schedule;
+ r5.h = .Lkernel_schedule;
+ reti = r5;
+ rti;
+.Lkernel_schedule:
+ [--sp] = rets;
+ sp += -12;
+ pseudo_long_call _preempt_schedule_irq, p4;
+ sp += 12;
+ rets = [sp++];
+
+ [--sp] = rets;
+ sp += -12;
+ /* up to irq14 so that reti after restore_all can return to irq15(kernel) */
+ pseudo_long_call _up_to_irq14, p4;
+ sp += 12;
+ rets = [sp++];
+
+ reti = r6; /* restore reti so that origin process can return to interrupted point */
+
+ jump .Lneed_schedule;
#else
-#define _resume_kernel_from_int 2f
+
+#define _resume_kernel_from_int .Lreturn_to_kernel
#endif
ENTRY(_return_from_int)
@@ -913,7 +1019,7 @@
p2.h = hi(ILAT);
r0 = [p2];
cc = bittst (r0, EVT_IVG15_P);
- if cc jump 2f;
+ if cc jump .Lreturn_to_kernel;
/* if not return to user mode, get out */
p2.l = lo(IPEND);
@@ -945,7 +1051,7 @@
STI r0;
raise 15; /* raise evt15 to do signal or reschedule */
rti;
-2:
+.Lreturn_to_kernel:
rts;
ENDPROC(_return_from_int)
@@ -1631,6 +1737,7 @@
.long _sys_fanotify_init
.long _sys_fanotify_mark
.long _sys_prlimit64
+ .long _sys_cacheflush
.rept NR_syscalls-(.-_sys_call_table)/4
.long _sys_ni_syscall
diff --git a/arch/blackfin/mach-common/interrupt.S b/arch/blackfin/mach-common/interrupt.S
index cee62cf..2df37db 100644
--- a/arch/blackfin/mach-common/interrupt.S
+++ b/arch/blackfin/mach-common/interrupt.S
@@ -116,7 +116,24 @@
cc = r0 == 0;
if cc jump .Lcommon_restore_context;
#else /* CONFIG_IPIPE */
+
+#ifdef CONFIG_PREEMPT
+ r7 = sp;
+ r4.l = lo(ALIGN_PAGE_MASK);
+ r4.h = hi(ALIGN_PAGE_MASK);
+ r7 = r7 & r4;
+ p5 = r7;
+ r7 = [p5 + TI_PREEMPT]; /* get preempt count */
+ r7 += 1; /* increment it */
+ [p5 + TI_PREEMPT] = r7;
+#endif
pseudo_long_call _do_irq, p2;
+
+#ifdef CONFIG_PREEMPT
+ r7 += -1;
+ [p5 + TI_PREEMPT] = r7; /* restore preempt count */
+#endif
+
SP += 12;
#endif /* CONFIG_IPIPE */
pseudo_long_call _return_from_int, p2;
diff --git a/arch/blackfin/mach-common/ints-priority.c b/arch/blackfin/mach-common/ints-priority.c
index eaece5f..da7e3c6 100644
--- a/arch/blackfin/mach-common/ints-priority.c
+++ b/arch/blackfin/mach-common/ints-priority.c
@@ -511,7 +511,7 @@
int i, irq = 0;
u32 status = bfin_read_EMAC_SYSTAT();
- for (i = 0; i < (IRQ_MAC_STMDONE - IRQ_MAC_PHYINT); i++)
+ for (i = 0; i <= (IRQ_MAC_STMDONE - IRQ_MAC_PHYINT); i++)
if (status & (1L << i)) {
irq = IRQ_MAC_PHYINT + i;
break;
@@ -529,8 +529,9 @@
} else
printk(KERN_ERR
"%s : %s : LINE %d :\nIRQ ?: MAC ERROR"
- " INTERRUPT ASSERTED BUT NO SOURCE FOUND\n",
- __func__, __FILE__, __LINE__);
+ " INTERRUPT ASSERTED BUT NO SOURCE FOUND"
+ "(EMAC_SYSTAT=0x%X)\n",
+ __func__, __FILE__, __LINE__, status);
}
#endif
@@ -1298,7 +1299,7 @@
} else {
struct ivgx *ivg = ivg7_13[vec - IVG7].ifirst;
struct ivgx *ivg_stop = ivg7_13[vec - IVG7].istop;
-#if defined(SIC_ISR0) || defined(SICA_ISR0)
+#if defined(SIC_ISR0)
unsigned long sic_status[3];
if (smp_processor_id()) {
@@ -1378,7 +1379,7 @@
if (likely(vec == EVT_IVTMR_P))
irq = IRQ_CORETMR;
else {
-#if defined(SIC_ISR0) || defined(SICA_ISR0)
+#if defined(SIC_ISR0)
unsigned long sic_status[3];
sic_status[0] = bfin_read_SIC_ISR0() & bfin_read_SIC_IMASK0();
diff --git a/arch/blackfin/mm/init.c b/arch/blackfin/mm/init.c
index bb4e8ff..f8435cd 100644
--- a/arch/blackfin/mm/init.c
+++ b/arch/blackfin/mm/init.c
@@ -158,5 +158,8 @@
free_init_pages("unused kernel memory",
(unsigned long)(&__init_begin),
(unsigned long)(&__init_end));
+
+ if (memory_start == (unsigned long)(&__init_end))
+ memory_start = (unsigned long)(&__init_begin);
#endif
}