drivers/net: Trim trailing whitespace
Signed-off-by: Jeff Garzik <jeff@garzik.org>
diff --git a/drivers/net/hp100.h b/drivers/net/hp100.h
index 236d945..e6ca128 100644
--- a/drivers/net/hp100.h
+++ b/drivers/net/hp100.h
@@ -8,9 +8,9 @@
*
* This driver is based on the 'hpfepkt' crynwr packet driver.
*
- * This source/code is public free; you can distribute it and/or modify
+ * This source/code is public free; you can distribute it and/or modify
* it under terms of the GNU General Public License (published by the
- * Free Software Foundation) either version two of this License, or any
+ * Free Software Foundation) either version two of this License, or any
* later version.
*/
@@ -18,7 +18,7 @@
* Hardware Constants
****************************************************************************/
-/*
+/*
* Page Identifiers
* (Swap Paging Register, PAGING, bits 3:0, Offset 0x02)
*/
@@ -143,15 +143,15 @@
/* ------------------------------------------------------------------------ */
-/*
+/*
* Hardware ID Register I (Always available, HW_ID, Offset 0x00)
*/
#define HP100_HW_ID_CASCADE 0x4850 /* Identifies Cascade Chip */
-/*
+/*
* Hardware ID Register 2 & Paging Register
* (Always available, PAGING, Offset 0x02)
- * Bits 15:4 are for the Chip ID
+ * Bits 15:4 are for the Chip ID
*/
#define HP100_CHIPID_MASK 0xFFF0
#define HP100_CHIPID_SHASTA 0x5350 /* Not 802.12 compliant */
@@ -162,7 +162,7 @@
/* LRF supported */
/*
- * Option Registers I and II
+ * Option Registers I and II
* (Always available, OPTION_LSW, Offset 0x04-0x05)
*/
#define HP100_DEBUG_EN 0x8000 /* 0:Dis., 1:Enable Debug Dump Ptr. */
@@ -187,7 +187,7 @@
/* NIC reset on 0 to 1 transition */
/*
- * Option Register III
+ * Option Register III
* (Always available, OPTION_MSW, Offset 0x06)
*/
#define HP100_PRIORITY_TX 0x0080 /* 1:Do all Tx pkts as priority */
@@ -253,7 +253,7 @@
#define HP100_BM_PCI_8CLK 0x40 /* ... cycles 8 clocks apart */
-/*
+/*
* Mode Control Register I
* (Page HW_MAP, MODECTRL1, Offset0x10)
*/
@@ -281,7 +281,7 @@
#define HP100_EN_BUS_FAIL 0x80 /* Enables bus-fail portion of misc */
/* interrupt */
-/*
+/*
* PCI Configuration and Control Register I
* (Page HW_MAP, PCICTRL1, Offset 0x12)
*/
@@ -378,7 +378,7 @@
/*
* 100MB LAN Control and Configuration Register
- * (Page MAC_CTRL, VG_LAN_CFG_1, Offset 0x0a)
+ * (Page MAC_CTRL, VG_LAN_CFG_1, Offset 0x0a)
*/
#define HP100_VG_SEL 0x80 /* 0:No, 1:Yes use 100 Mbit MAC */
#define HP100_LINK_UP_ST 0x40 /* 0:No, 1:Yes endnode logged in */
@@ -422,7 +422,7 @@
#define HP100_MAC1MODE7 HP100_MAC1MODE6 | HP100_ACC_ERRORED
/*
- * MAC Configuration Register II
+ * MAC Configuration Register II
* (Page MAC_CTRL, MAC_CFG_2, Offset 0x0d)
*/
#define HP100_TR_MODE 0x80 /* 0:No, 1:Yes support Token Ring formats */
@@ -447,8 +447,8 @@
#define HP100_MAC2MODE7 KEEP_CRC
/*
- * MAC Configuration Register III
- * (Page MAC_CTRL, MAC_CFG_3, Offset 0x0e)
+ * MAC Configuration Register III
+ * (Page MAC_CTRL, MAC_CFG_3, Offset 0x0e)
*/
#define HP100_PACKET_PACE 0x03 /* Packet Pacing:
* 00: No packet pacing
@@ -461,7 +461,7 @@
#define HP100_AUTO_MODE 0x10 /* 1: AutoSelect between 10/100 */
/*
- * MAC Configuration Register IV
+ * MAC Configuration Register IV
* (Page MAC_CTRL, MAC_CFG_4, Offset 0x0f)
*/
#define HP100_MAC_SEL_ST 0x01 /* (R): Status of external VGSEL
@@ -469,18 +469,18 @@
#define HP100_LINK_FAIL_ST 0x02 /* (R): Status of Link Fail portion
* of the Misc. Interrupt */
-/*
- * 100 MB LAN Training Request/Allowed Registers
+/*
+ * 100 MB LAN Training Request/Allowed Registers
* (Page MAC_CTRL, TRAIN_REQUEST and TRAIN_ALLOW, Offset 0x14-0x16)(ETR parts only)
*/
-#define HP100_MACRQ_REPEATER 0x0001 /* 1: MAC tells HUB it wants to be
+#define HP100_MACRQ_REPEATER 0x0001 /* 1: MAC tells HUB it wants to be
* a cascaded repeater
* 0: ... wants to be a DTE */
#define HP100_MACRQ_PROMSC 0x0006 /* 2 bits: Promiscious mode
* 00: Rcv only unicast packets
* specifically addr to this
* endnode
- * 10: Rcv all pckts fwded by
+ * 10: Rcv all pckts fwded by
* the local repeater */
#define HP100_MACRQ_FRAMEFMT_EITHER 0x0018 /* 11: either format allowed */
#define HP100_MACRQ_FRAMEFMT_802_3 0x0000 /* 00: 802.3 is requested */
@@ -492,7 +492,7 @@
* 00: Rcv only unicast packets
* specifically addr to this
* endnode
- * 10: Rcv all pckts fwded by
+ * 10: Rcv all pckts fwded by
* the local repeater */
#define HP100_MALLOW_FRAMEFMT 0x00e0 /* 2 bits: Frame Format
* 00: 802.3 format will be used
@@ -521,7 +521,7 @@
#define HP100_LAN_COAX 9 /* lan_type value for Coax */
#define HP100_LAN_ERR (-1) /* lan_type value for link down */
-/*
+/*
* Bus Master Data Structures ----------------------------------------------
*/
@@ -554,7 +554,7 @@
#define HP100_PKT_LEN_MASK 0x1FFF /* AND with RxLength to get length */
-/* Receive Packet Status. Note, the error bits are only valid if ACC_ERRORED
+/* Receive Packet Status. Note, the error bits are only valid if ACC_ERRORED
bit in the MAC Configuration Register 1 is set. */
#define HP100_RX_PRI 0x8000 /* 0:No, 1:Yes packet is priority */
#define HP100_SDF_ERR 0x4000 /* 0:No, 1:Yes start of frame error */