ixgb: fix spelling errors
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
diff --git a/drivers/net/ixgb/ixgb.h b/drivers/net/ixgb/ixgb.h
index 69529ec..6cb4dde 100644
--- a/drivers/net/ixgb/ixgb.h
+++ b/drivers/net/ixgb/ixgb.h
@@ -94,8 +94,8 @@
#define MIN_TXD 64
/* hardware cannot reliably support more than 512 descriptors owned by
- * hardware descrioptor cache otherwise an unreliable ring under heavy
- * recieve load may result */
+ * hardware descriptor cache otherwise an unreliable ring under heavy
+ * receive load may result */
/* #define DEFAULT_RXD 1024 */
/* #define MAX_RXD 4096 */
#define DEFAULT_RXD 512
diff --git a/drivers/net/ixgb/ixgb_ee.c b/drivers/net/ixgb/ixgb_ee.c
index 8bc9716..aa71b9b 100644
--- a/drivers/net/ixgb/ixgb_ee.c
+++ b/drivers/net/ixgb/ixgb_ee.c
@@ -205,7 +205,7 @@
eecd_reg = IXGB_READ_REG(hw, EECD);
- /* Deselct EEPROM */
+ /* Deselect EEPROM */
eecd_reg &= ~(IXGB_EECD_CS | IXGB_EECD_SK);
IXGB_WRITE_REG(hw, EECD, eecd_reg);
udelay(50);
@@ -293,7 +293,7 @@
*/
ixgb_standby_eeprom(hw);
- /* Now read DO repeatedly until is high (equal to '1'). The EEEPROM will
+ /* Now read DO repeatedly until is high (equal to '1'). The EEPROM will
* signal that the command has been completed by raising the DO signal.
* If DO does not go high in 10 milliseconds, then error out.
*/
@@ -365,7 +365,7 @@
*
* hw - Struct containing variables accessed by shared code
* reg - offset within the EEPROM to be written to
- * data - 16 bit word to be writen to the EEPROM
+ * data - 16 bit word to be written to the EEPROM
*
* If ixgb_update_eeprom_checksum is not called after this function, the
* EEPROM will most likely contain an invalid checksum.
diff --git a/drivers/net/ixgb/ixgb_ee.h b/drivers/net/ixgb/ixgb_ee.h
index 4b7bd0d..12136b6 100644
--- a/drivers/net/ixgb/ixgb_ee.h
+++ b/drivers/net/ixgb/ixgb_ee.h
@@ -34,11 +34,11 @@
#define IXGB_ETH_LENGTH_OF_ADDRESS 6
/* EEPROM Commands */
-#define EEPROM_READ_OPCODE 0x6 /* EERPOM read opcode */
-#define EEPROM_WRITE_OPCODE 0x5 /* EERPOM write opcode */
-#define EEPROM_ERASE_OPCODE 0x7 /* EERPOM erase opcode */
-#define EEPROM_EWEN_OPCODE 0x13 /* EERPOM erase/write enable */
-#define EEPROM_EWDS_OPCODE 0x10 /* EERPOM erast/write disable */
+#define EEPROM_READ_OPCODE 0x6 /* EEPROM read opcode */
+#define EEPROM_WRITE_OPCODE 0x5 /* EEPROM write opcode */
+#define EEPROM_ERASE_OPCODE 0x7 /* EEPROM erase opcode */
+#define EEPROM_EWEN_OPCODE 0x13 /* EEPROM erase/write enable */
+#define EEPROM_EWDS_OPCODE 0x10 /* EEPROM erase/write disable */
/* EEPROM MAP (Word Offsets) */
#define EEPROM_IA_1_2_REG 0x0000
diff --git a/drivers/net/ixgb/ixgb_hw.c b/drivers/net/ixgb/ixgb_hw.c
index d023fb5..3694e8c 100644
--- a/drivers/net/ixgb/ixgb_hw.c
+++ b/drivers/net/ixgb/ixgb_hw.c
@@ -371,7 +371,7 @@
* hw - Struct containing variables accessed by shared code
*
* Places the MAC address in receive address register 0 and clears the rest
- * of the receive addresss registers. Clears the multicast table. Assumes
+ * of the receive address registers. Clears the multicast table. Assumes
* the receiver is in reset when the routine is called.
*****************************************************************************/
static void
@@ -964,7 +964,7 @@
}
/******************************************************************************
- * Check for a bad link condition that may have occured.
+ * Check for a bad link condition that may have occurred.
* The indication is that the RFC / LFC registers may be incrementing
* continually. A full adapter reset is required to recover.
*
diff --git a/drivers/net/ixgb/ixgb_main.c b/drivers/net/ixgb/ixgb_main.c
index fc211a3..796f011 100644
--- a/drivers/net/ixgb/ixgb_main.c
+++ b/drivers/net/ixgb/ixgb_main.c
@@ -2248,7 +2248,7 @@
* ixgb_io_slot_reset - called after the pci bus has been reset.
* @pdev pointer to pci device with error
*
- * This callback is called after the PCI buss has been reset.
+ * This callback is called after the PCI bus has been reset.
* Basically, this tries to restart the card from scratch.
* This is a shortened version of the device probe/discovery code,
* it resembles the first-half of the ixgb_probe() routine.