rt2x00: Implement support for 802.11n
Extend rt2x00lib capabilities to support 802.11n,
it still lacks aggregation support, but that can
be added in the future.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/drivers/net/wireless/rt2x00/rt2x00queue.h b/drivers/net/wireless/rt2x00/rt2x00queue.h
index 13e0ece..b5e0634 100644
--- a/drivers/net/wireless/rt2x00/rt2x00queue.h
+++ b/drivers/net/wireless/rt2x00/rt2x00queue.h
@@ -35,9 +35,12 @@
* for USB devices this restriction does not apply, but the value of
* 2432 makes sense since it is big enough to contain the maximum fragment
* size according to the ieee802.11 specs.
+ * The aggregation size depends on support from the driver, but should
+ * be something around 3840 bytes.
*/
-#define DATA_FRAME_SIZE 2432
-#define MGMT_FRAME_SIZE 256
+#define DATA_FRAME_SIZE 2432
+#define MGMT_FRAME_SIZE 256
+#define AGGREGATION_SIZE 3840
/**
* DOC: Number of entries per queue
@@ -148,18 +151,20 @@
*
* @RXDONE_SIGNAL_PLCP: Signal field contains the plcp value.
* @RXDONE_SIGNAL_BITRATE: Signal field contains the bitrate value.
+ * @RXDONE_SIGNAL_MCS: Signal field contains the mcs value.
* @RXDONE_MY_BSS: Does this frame originate from device's BSS.
* @RXDONE_CRYPTO_IV: Driver provided IV/EIV data.
* @RXDONE_CRYPTO_ICV: Driver provided ICV data.
* @RXDONE_L2PAD: 802.11 payload has been padded to 4-byte boundary.
*/
enum rxdone_entry_desc_flags {
- RXDONE_SIGNAL_PLCP = 1 << 0,
- RXDONE_SIGNAL_BITRATE = 1 << 1,
- RXDONE_MY_BSS = 1 << 2,
- RXDONE_CRYPTO_IV = 1 << 3,
- RXDONE_CRYPTO_ICV = 1 << 4,
- RXDONE_L2PAD = 1 << 5,
+ RXDONE_SIGNAL_PLCP = BIT(0),
+ RXDONE_SIGNAL_BITRATE = BIT(1),
+ RXDONE_SIGNAL_MCS = BIT(2),
+ RXDONE_MY_BSS = BIT(3),
+ RXDONE_CRYPTO_IV = BIT(4),
+ RXDONE_CRYPTO_ICV = BIT(5),
+ RXDONE_L2PAD = BIT(6),
};
/**
@@ -168,7 +173,7 @@
* from &rxdone_entry_desc to a signal value type.
*/
#define RXDONE_SIGNAL_MASK \
- ( RXDONE_SIGNAL_PLCP | RXDONE_SIGNAL_BITRATE )
+ ( RXDONE_SIGNAL_PLCP | RXDONE_SIGNAL_BITRATE | RXDONE_SIGNAL_MCS )
/**
* struct rxdone_entry_desc: RX Entry descriptor
@@ -182,6 +187,7 @@
* @size: Data size of the received frame.
* @flags: MAC80211 receive flags (See &enum mac80211_rx_flags).
* @dev_flags: Ralink receive flags (See &enum rxdone_entry_desc_flags).
+ * @rate_mode: Rate mode (See @enum rate_modulation).
* @cipher: Cipher type used during decryption.
* @cipher_status: Decryption status.
* @iv: IV/EIV data used during decryption.
@@ -195,6 +201,7 @@
int size;
int flags;
int dev_flags;
+ u16 rate_mode;
u8 cipher;
u8 cipher_status;
@@ -248,6 +255,9 @@
* @ENTRY_TXD_ENCRYPT_PAIRWISE: Use pairwise key table (instead of shared).
* @ENTRY_TXD_ENCRYPT_IV: Generate IV/EIV in hardware.
* @ENTRY_TXD_ENCRYPT_MMIC: Generate MIC in hardware.
+ * @ENTRY_TXD_HT_AMPDU: This frame is part of an AMPDU.
+ * @ENTRY_TXD_HT_BW_40: Use 40MHz Bandwidth.
+ * @ENTRY_TXD_HT_SHORT_GI: Use short GI.
*/
enum txentry_desc_flags {
ENTRY_TXD_RTS_FRAME,
@@ -263,6 +273,9 @@
ENTRY_TXD_ENCRYPT_PAIRWISE,
ENTRY_TXD_ENCRYPT_IV,
ENTRY_TXD_ENCRYPT_MMIC,
+ ENTRY_TXD_HT_AMPDU,
+ ENTRY_TXD_HT_BW_40,
+ ENTRY_TXD_HT_SHORT_GI,
};
/**
@@ -278,7 +291,11 @@
* @length_low: PLCP length low word.
* @signal: PLCP signal.
* @service: PLCP service.
+ * @msc: MCS.
+ * @stbc: STBC.
+ * @ba_size: BA size.
* @rate_mode: Rate mode (See @enum rate_modulation).
+ * @mpdu_density: MDPU density.
* @retry_limit: Max number of retries.
* @aifs: AIFS value.
* @ifs: IFS value.
@@ -302,7 +319,11 @@
u16 signal;
u16 service;
+ u16 mcs;
+ u16 stbc;
+ u16 ba_size;
u16 rate_mode;
+ u16 mpdu_density;
short retry_limit;
short aifs;