MIPS: Alchemy: remove au_read/write/sync
replace au_read/write/sync with __raw_read/write and wmb.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7465/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
diff --git a/drivers/mmc/host/au1xmmc.c b/drivers/mmc/host/au1xmmc.c
index 0ea43c0..2988e9d 100644
--- a/drivers/mmc/host/au1xmmc.c
+++ b/drivers/mmc/host/au1xmmc.c
@@ -90,7 +90,7 @@
struct mmc_request *mrq;
u32 flags;
- u32 iobase;
+ void __iomem *iobase;
u32 clock;
u32 bus_width;
u32 power_mode;
@@ -162,32 +162,33 @@
static inline void IRQ_ON(struct au1xmmc_host *host, u32 mask)
{
- u32 val = au_readl(HOST_CONFIG(host));
+ u32 val = __raw_readl(HOST_CONFIG(host));
val |= mask;
- au_writel(val, HOST_CONFIG(host));
- au_sync();
+ __raw_writel(val, HOST_CONFIG(host));
+ wmb(); /* drain writebuffer */
}
static inline void FLUSH_FIFO(struct au1xmmc_host *host)
{
- u32 val = au_readl(HOST_CONFIG2(host));
+ u32 val = __raw_readl(HOST_CONFIG2(host));
- au_writel(val | SD_CONFIG2_FF, HOST_CONFIG2(host));
- au_sync_delay(1);
+ __raw_writel(val | SD_CONFIG2_FF, HOST_CONFIG2(host));
+ wmb(); /* drain writebuffer */
+ mdelay(1);
/* SEND_STOP will turn off clock control - this re-enables it */
val &= ~SD_CONFIG2_DF;
- au_writel(val, HOST_CONFIG2(host));
- au_sync();
+ __raw_writel(val, HOST_CONFIG2(host));
+ wmb(); /* drain writebuffer */
}
static inline void IRQ_OFF(struct au1xmmc_host *host, u32 mask)
{
- u32 val = au_readl(HOST_CONFIG(host));
+ u32 val = __raw_readl(HOST_CONFIG(host));
val &= ~mask;
- au_writel(val, HOST_CONFIG(host));
- au_sync();
+ __raw_writel(val, HOST_CONFIG(host));
+ wmb(); /* drain writebuffer */
}
static inline void SEND_STOP(struct au1xmmc_host *host)
@@ -197,12 +198,13 @@
WARN_ON(host->status != HOST_S_DATA);
host->status = HOST_S_STOP;
- config2 = au_readl(HOST_CONFIG2(host));
- au_writel(config2 | SD_CONFIG2_DF, HOST_CONFIG2(host));
- au_sync();
+ config2 = __raw_readl(HOST_CONFIG2(host));
+ __raw_writel(config2 | SD_CONFIG2_DF, HOST_CONFIG2(host));
+ wmb(); /* drain writebuffer */
/* Send the stop command */
- au_writel(STOP_CMD, HOST_CMD(host));
+ __raw_writel(STOP_CMD, HOST_CMD(host));
+ wmb(); /* drain writebuffer */
}
static void au1xmmc_set_power(struct au1xmmc_host *host, int state)
@@ -296,28 +298,28 @@
}
}
- au_writel(cmd->arg, HOST_CMDARG(host));
- au_sync();
+ __raw_writel(cmd->arg, HOST_CMDARG(host));
+ wmb(); /* drain writebuffer */
if (wait)
IRQ_OFF(host, SD_CONFIG_CR);
- au_writel((mmccmd | SD_CMD_GO), HOST_CMD(host));
- au_sync();
+ __raw_writel((mmccmd | SD_CMD_GO), HOST_CMD(host));
+ wmb(); /* drain writebuffer */
/* Wait for the command to go on the line */
- while (au_readl(HOST_CMD(host)) & SD_CMD_GO)
+ while (__raw_readl(HOST_CMD(host)) & SD_CMD_GO)
/* nop */;
/* Wait for the command to come back */
if (wait) {
- u32 status = au_readl(HOST_STATUS(host));
+ u32 status = __raw_readl(HOST_STATUS(host));
while (!(status & SD_STATUS_CR))
- status = au_readl(HOST_STATUS(host));
+ status = __raw_readl(HOST_STATUS(host));
/* Clear the CR status */
- au_writel(SD_STATUS_CR, HOST_STATUS(host));
+ __raw_writel(SD_STATUS_CR, HOST_STATUS(host));
IRQ_ON(host, SD_CONFIG_CR);
}
@@ -339,11 +341,11 @@
data = mrq->cmd->data;
if (status == 0)
- status = au_readl(HOST_STATUS(host));
+ status = __raw_readl(HOST_STATUS(host));
/* The transaction is really over when the SD_STATUS_DB bit is clear */
while ((host->flags & HOST_F_XMIT) && (status & SD_STATUS_DB))
- status = au_readl(HOST_STATUS(host));
+ status = __raw_readl(HOST_STATUS(host));
data->error = 0;
dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len, host->dma.dir);
@@ -357,7 +359,7 @@
data->error = -EILSEQ;
/* Clear the CRC bits */
- au_writel(SD_STATUS_WC | SD_STATUS_RC, HOST_STATUS(host));
+ __raw_writel(SD_STATUS_WC | SD_STATUS_RC, HOST_STATUS(host));
data->bytes_xfered = 0;
@@ -380,7 +382,7 @@
{
struct au1xmmc_host *host = (struct au1xmmc_host *)param;
- u32 status = au_readl(HOST_STATUS(host));
+ u32 status = __raw_readl(HOST_STATUS(host));
au1xmmc_data_complete(host, status);
}
@@ -412,15 +414,15 @@
max = AU1XMMC_MAX_TRANSFER;
for (count = 0; count < max; count++) {
- status = au_readl(HOST_STATUS(host));
+ status = __raw_readl(HOST_STATUS(host));
if (!(status & SD_STATUS_TH))
break;
val = *sg_ptr++;
- au_writel((unsigned long)val, HOST_TXPORT(host));
- au_sync();
+ __raw_writel((unsigned long)val, HOST_TXPORT(host));
+ wmb(); /* drain writebuffer */
}
host->pio.len -= count;
@@ -472,7 +474,7 @@
max = AU1XMMC_MAX_TRANSFER;
for (count = 0; count < max; count++) {
- status = au_readl(HOST_STATUS(host));
+ status = __raw_readl(HOST_STATUS(host));
if (!(status & SD_STATUS_NE))
break;
@@ -494,7 +496,7 @@
break;
}
- val = au_readl(HOST_RXPORT(host));
+ val = __raw_readl(HOST_RXPORT(host));
if (sg_ptr)
*sg_ptr++ = (unsigned char)(val & 0xFF);
@@ -537,10 +539,10 @@
if (cmd->flags & MMC_RSP_PRESENT) {
if (cmd->flags & MMC_RSP_136) {
- r[0] = au_readl(host->iobase + SD_RESP3);
- r[1] = au_readl(host->iobase + SD_RESP2);
- r[2] = au_readl(host->iobase + SD_RESP1);
- r[3] = au_readl(host->iobase + SD_RESP0);
+ r[0] = __raw_readl(host->iobase + SD_RESP3);
+ r[1] = __raw_readl(host->iobase + SD_RESP2);
+ r[2] = __raw_readl(host->iobase + SD_RESP1);
+ r[3] = __raw_readl(host->iobase + SD_RESP0);
/* The CRC is omitted from the response, so really
* we only got 120 bytes, but the engine expects
@@ -559,7 +561,7 @@
* that means that the OSR data starts at bit 31,
* so we can just read RESP0 and return that.
*/
- cmd->resp[0] = au_readl(host->iobase + SD_RESP0);
+ cmd->resp[0] = __raw_readl(host->iobase + SD_RESP0);
}
}
@@ -586,7 +588,7 @@
u32 mask = SD_STATUS_DB | SD_STATUS_NE;
while((status & mask) != mask)
- status = au_readl(HOST_STATUS(host));
+ status = __raw_readl(HOST_STATUS(host));
}
au1xxx_dbdma_start(channel);
@@ -606,13 +608,13 @@
pbus /= 2;
divisor = ((pbus / rate) / 2) - 1;
- config = au_readl(HOST_CONFIG(host));
+ config = __raw_readl(HOST_CONFIG(host));
config &= ~(SD_CONFIG_DIV);
config |= (divisor & SD_CONFIG_DIV) | SD_CONFIG_DE;
- au_writel(config, HOST_CONFIG(host));
- au_sync();
+ __raw_writel(config, HOST_CONFIG(host));
+ wmb(); /* drain writebuffer */
}
static int au1xmmc_prepare_data(struct au1xmmc_host *host,
@@ -636,7 +638,7 @@
if (host->dma.len == 0)
return -ETIMEDOUT;
- au_writel(data->blksz - 1, HOST_BLKSIZE(host));
+ __raw_writel(data->blksz - 1, HOST_BLKSIZE(host));
if (host->flags & (HOST_F_DMA | HOST_F_DBDMA)) {
int i;
@@ -723,31 +725,34 @@
static void au1xmmc_reset_controller(struct au1xmmc_host *host)
{
/* Apply the clock */
- au_writel(SD_ENABLE_CE, HOST_ENABLE(host));
- au_sync_delay(1);
+ __raw_writel(SD_ENABLE_CE, HOST_ENABLE(host));
+ wmb(); /* drain writebuffer */
+ mdelay(1);
- au_writel(SD_ENABLE_R | SD_ENABLE_CE, HOST_ENABLE(host));
- au_sync_delay(5);
+ __raw_writel(SD_ENABLE_R | SD_ENABLE_CE, HOST_ENABLE(host));
+ wmb(); /* drain writebuffer */
+ mdelay(5);
- au_writel(~0, HOST_STATUS(host));
- au_sync();
+ __raw_writel(~0, HOST_STATUS(host));
+ wmb(); /* drain writebuffer */
- au_writel(0, HOST_BLKSIZE(host));
- au_writel(0x001fffff, HOST_TIMEOUT(host));
- au_sync();
+ __raw_writel(0, HOST_BLKSIZE(host));
+ __raw_writel(0x001fffff, HOST_TIMEOUT(host));
+ wmb(); /* drain writebuffer */
- au_writel(SD_CONFIG2_EN, HOST_CONFIG2(host));
- au_sync();
+ __raw_writel(SD_CONFIG2_EN, HOST_CONFIG2(host));
+ wmb(); /* drain writebuffer */
- au_writel(SD_CONFIG2_EN | SD_CONFIG2_FF, HOST_CONFIG2(host));
- au_sync_delay(1);
+ __raw_writel(SD_CONFIG2_EN | SD_CONFIG2_FF, HOST_CONFIG2(host));
+ wmb(); /* drain writebuffer */
+ mdelay(1);
- au_writel(SD_CONFIG2_EN, HOST_CONFIG2(host));
- au_sync();
+ __raw_writel(SD_CONFIG2_EN, HOST_CONFIG2(host));
+ wmb(); /* drain writebuffer */
/* Configure interrupts */
- au_writel(AU1XMMC_INTERRUPTS, HOST_CONFIG(host));
- au_sync();
+ __raw_writel(AU1XMMC_INTERRUPTS, HOST_CONFIG(host));
+ wmb(); /* drain writebuffer */
}
@@ -767,7 +772,7 @@
host->clock = ios->clock;
}
- config2 = au_readl(HOST_CONFIG2(host));
+ config2 = __raw_readl(HOST_CONFIG2(host));
switch (ios->bus_width) {
case MMC_BUS_WIDTH_8:
config2 |= SD_CONFIG2_BB;
@@ -780,8 +785,8 @@
config2 &= ~(SD_CONFIG2_WB | SD_CONFIG2_BB);
break;
}
- au_writel(config2, HOST_CONFIG2(host));
- au_sync();
+ __raw_writel(config2, HOST_CONFIG2(host));
+ wmb(); /* drain writebuffer */
}
#define STATUS_TIMEOUT (SD_STATUS_RAT | SD_STATUS_DT)
@@ -793,7 +798,7 @@
struct au1xmmc_host *host = dev_id;
u32 status;
- status = au_readl(HOST_STATUS(host));
+ status = __raw_readl(HOST_STATUS(host));
if (!(status & SD_STATUS_I))
return IRQ_NONE; /* not ours */
@@ -839,8 +844,8 @@
status);
}
- au_writel(status, HOST_STATUS(host));
- au_sync();
+ __raw_writel(status, HOST_STATUS(host));
+ wmb(); /* drain writebuffer */
return IRQ_HANDLED;
}
@@ -976,7 +981,7 @@
goto out1;
}
- host->iobase = (unsigned long)ioremap(r->start, 0x3c);
+ host->iobase = ioremap(r->start, 0x3c);
if (!host->iobase) {
dev_err(&pdev->dev, "cannot remap mmio\n");
goto out2;
@@ -1075,7 +1080,7 @@
platform_set_drvdata(pdev, host);
- pr_info(DRIVER_NAME ": MMC Controller %d set up at %8.8X"
+ pr_info(DRIVER_NAME ": MMC Controller %d set up at %p"
" (mode=%s)\n", pdev->id, host->iobase,
host->flags & HOST_F_DMA ? "dma" : "pio");
@@ -1087,10 +1092,10 @@
led_classdev_unregister(host->platdata->led);
out5:
#endif
- au_writel(0, HOST_ENABLE(host));
- au_writel(0, HOST_CONFIG(host));
- au_writel(0, HOST_CONFIG2(host));
- au_sync();
+ __raw_writel(0, HOST_ENABLE(host));
+ __raw_writel(0, HOST_CONFIG(host));
+ __raw_writel(0, HOST_CONFIG2(host));
+ wmb(); /* drain writebuffer */
if (host->flags & HOST_F_DBDMA)
au1xmmc_dbdma_shutdown(host);
@@ -1130,10 +1135,10 @@
!(host->mmc->caps & MMC_CAP_NEEDS_POLL))
host->platdata->cd_setup(host->mmc, 0);
- au_writel(0, HOST_ENABLE(host));
- au_writel(0, HOST_CONFIG(host));
- au_writel(0, HOST_CONFIG2(host));
- au_sync();
+ __raw_writel(0, HOST_ENABLE(host));
+ __raw_writel(0, HOST_CONFIG(host));
+ __raw_writel(0, HOST_CONFIG2(host));
+ wmb(); /* drain writebuffer */
tasklet_kill(&host->data_task);
tasklet_kill(&host->finish_task);
@@ -1158,11 +1163,11 @@
{
struct au1xmmc_host *host = platform_get_drvdata(pdev);
- au_writel(0, HOST_CONFIG2(host));
- au_writel(0, HOST_CONFIG(host));
- au_writel(0xffffffff, HOST_STATUS(host));
- au_writel(0, HOST_ENABLE(host));
- au_sync();
+ __raw_writel(0, HOST_CONFIG2(host));
+ __raw_writel(0, HOST_CONFIG(host));
+ __raw_writel(0xffffffff, HOST_STATUS(host));
+ __raw_writel(0, HOST_ENABLE(host));
+ wmb(); /* drain writebuffer */
return 0;
}
diff --git a/drivers/mtd/nand/au1550nd.c b/drivers/mtd/nand/au1550nd.c
index 6cece6e..77d6c17 100644
--- a/drivers/mtd/nand/au1550nd.c
+++ b/drivers/mtd/nand/au1550nd.c
@@ -41,7 +41,7 @@
{
struct nand_chip *this = mtd->priv;
u_char ret = readb(this->IO_ADDR_R);
- au_sync();
+ wmb(); /* drain writebuffer */
return ret;
}
@@ -56,7 +56,7 @@
{
struct nand_chip *this = mtd->priv;
writeb(byte, this->IO_ADDR_W);
- au_sync();
+ wmb(); /* drain writebuffer */
}
/**
@@ -69,7 +69,7 @@
{
struct nand_chip *this = mtd->priv;
u_char ret = (u_char) cpu_to_le16(readw(this->IO_ADDR_R));
- au_sync();
+ wmb(); /* drain writebuffer */
return ret;
}
@@ -84,7 +84,7 @@
{
struct nand_chip *this = mtd->priv;
writew(le16_to_cpu((u16) byte), this->IO_ADDR_W);
- au_sync();
+ wmb(); /* drain writebuffer */
}
/**
@@ -97,7 +97,7 @@
{
struct nand_chip *this = mtd->priv;
u16 ret = readw(this->IO_ADDR_R);
- au_sync();
+ wmb(); /* drain writebuffer */
return ret;
}
@@ -116,7 +116,7 @@
for (i = 0; i < len; i++) {
writeb(buf[i], this->IO_ADDR_W);
- au_sync();
+ wmb(); /* drain writebuffer */
}
}
@@ -135,7 +135,7 @@
for (i = 0; i < len; i++) {
buf[i] = readb(this->IO_ADDR_R);
- au_sync();
+ wmb(); /* drain writebuffer */
}
}
@@ -156,7 +156,7 @@
for (i = 0; i < len; i++) {
writew(p[i], this->IO_ADDR_W);
- au_sync();
+ wmb(); /* drain writebuffer */
}
}
@@ -178,7 +178,7 @@
for (i = 0; i < len; i++) {
p[i] = readw(this->IO_ADDR_R);
- au_sync();
+ wmb(); /* drain writebuffer */
}
}
@@ -234,8 +234,7 @@
this->IO_ADDR_R = this->IO_ADDR_W;
- /* Drain the writebuffer */
- au_sync();
+ wmb(); /* Drain the writebuffer */
}
int au1550_device_ready(struct mtd_info *mtd)
diff --git a/drivers/net/ethernet/amd/au1000_eth.c b/drivers/net/ethernet/amd/au1000_eth.c
index ad8b058..31c48a7 100644
--- a/drivers/net/ethernet/amd/au1000_eth.c
+++ b/drivers/net/ethernet/amd/au1000_eth.c
@@ -270,10 +270,12 @@
if (force_reset || (!aup->mac_enabled)) {
writel(MAC_EN_CLOCK_ENABLE, aup->enable);
- au_sync_delay(2);
+ wmb(); /* drain writebuffer */
+ mdelay(2);
writel((MAC_EN_RESET0 | MAC_EN_RESET1 | MAC_EN_RESET2
| MAC_EN_CLOCK_ENABLE), aup->enable);
- au_sync_delay(2);
+ wmb(); /* drain writebuffer */
+ mdelay(2);
aup->mac_enabled = 1;
}
@@ -391,7 +393,8 @@
reg = readl(&aup->mac->control);
reg &= ~(MAC_RX_ENABLE | MAC_TX_ENABLE);
writel(reg, &aup->mac->control);
- au_sync_delay(10);
+ wmb(); /* drain writebuffer */
+ mdelay(10);
}
static void au1000_enable_rx_tx(struct net_device *dev)
@@ -404,7 +407,8 @@
reg = readl(&aup->mac->control);
reg |= (MAC_RX_ENABLE | MAC_TX_ENABLE);
writel(reg, &aup->mac->control);
- au_sync_delay(10);
+ wmb(); /* drain writebuffer */
+ mdelay(10);
}
static void
@@ -454,7 +458,8 @@
reg |= MAC_DISABLE_RX_OWN;
}
writel(reg, &aup->mac->control);
- au_sync_delay(1);
+ wmb(); /* drain writebuffer */
+ mdelay(1);
au1000_enable_rx_tx(dev);
aup->old_duplex = phydev->duplex;
@@ -618,9 +623,11 @@
au1000_hard_stop(dev);
writel(MAC_EN_CLOCK_ENABLE, aup->enable);
- au_sync_delay(2);
+ wmb(); /* drain writebuffer */
+ mdelay(2);
writel(0, aup->enable);
- au_sync_delay(2);
+ wmb(); /* drain writebuffer */
+ mdelay(2);
aup->tx_full = 0;
for (i = 0; i < NUM_RX_DMA; i++) {
@@ -770,7 +777,7 @@
for (i = 0; i < NUM_RX_DMA; i++)
aup->rx_dma_ring[i]->buff_stat |= RX_DMA_ENABLE;
- au_sync();
+ wmb(); /* drain writebuffer */
control = MAC_RX_ENABLE | MAC_TX_ENABLE;
#ifndef CONFIG_CPU_LITTLE_ENDIAN
@@ -787,7 +794,7 @@
writel(control, &aup->mac->control);
writel(0x8100, &aup->mac->vlan1_tag); /* activate vlan support */
- au_sync();
+ wmb(); /* drain writebuffer */
spin_unlock_irqrestore(&aup->lock, flags);
return 0;
@@ -878,7 +885,7 @@
}
prxd->buff_stat = (u32)(pDB->dma_addr | RX_DMA_ENABLE);
aup->rx_head = (aup->rx_head + 1) & (NUM_RX_DMA - 1);
- au_sync();
+ wmb(); /* drain writebuffer */
/* next descriptor */
prxd = aup->rx_dma_ring[aup->rx_head];
@@ -926,7 +933,7 @@
au1000_update_tx_stats(dev, ptxd->status);
ptxd->buff_stat &= ~TX_T_DONE;
ptxd->len = 0;
- au_sync();
+ wmb(); /* drain writebuffer */
aup->tx_tail = (aup->tx_tail + 1) & (NUM_TX_DMA - 1);
ptxd = aup->tx_dma_ring[aup->tx_tail];
@@ -1057,7 +1064,7 @@
ps->tx_bytes += ptxd->len;
ptxd->buff_stat = pDB->dma_addr | TX_DMA_ENABLE;
- au_sync();
+ wmb(); /* drain writebuffer */
dev_kfree_skb(skb);
aup->tx_head = (aup->tx_head + 1) & (NUM_TX_DMA - 1);
return NETDEV_TX_OK;
diff --git a/drivers/spi/spi-au1550.c b/drivers/spi/spi-au1550.c
index 67375a1..ffb42f1 100644
--- a/drivers/spi/spi-au1550.c
+++ b/drivers/spi/spi-au1550.c
@@ -141,13 +141,13 @@
PSC_SPIMSK_MM | PSC_SPIMSK_RR | PSC_SPIMSK_RO
| PSC_SPIMSK_RU | PSC_SPIMSK_TR | PSC_SPIMSK_TO
| PSC_SPIMSK_TU | PSC_SPIMSK_SD | PSC_SPIMSK_MD;
- au_sync();
+ wmb(); /* drain writebuffer */
hw->regs->psc_spievent =
PSC_SPIEVNT_MM | PSC_SPIEVNT_RR | PSC_SPIEVNT_RO
| PSC_SPIEVNT_RU | PSC_SPIEVNT_TR | PSC_SPIEVNT_TO
| PSC_SPIEVNT_TU | PSC_SPIEVNT_SD | PSC_SPIEVNT_MD;
- au_sync();
+ wmb(); /* drain writebuffer */
}
static void au1550_spi_reset_fifos(struct au1550_spi *hw)
@@ -155,10 +155,10 @@
u32 pcr;
hw->regs->psc_spipcr = PSC_SPIPCR_RC | PSC_SPIPCR_TC;
- au_sync();
+ wmb(); /* drain writebuffer */
do {
pcr = hw->regs->psc_spipcr;
- au_sync();
+ wmb(); /* drain writebuffer */
} while (pcr != 0);
}
@@ -188,9 +188,9 @@
au1550_spi_bits_handlers_set(hw, spi->bits_per_word);
cfg = hw->regs->psc_spicfg;
- au_sync();
+ wmb(); /* drain writebuffer */
hw->regs->psc_spicfg = cfg & ~PSC_SPICFG_DE_ENABLE;
- au_sync();
+ wmb(); /* drain writebuffer */
if (spi->mode & SPI_CPOL)
cfg |= PSC_SPICFG_BI;
@@ -218,10 +218,10 @@
cfg |= au1550_spi_baudcfg(hw, spi->max_speed_hz);
hw->regs->psc_spicfg = cfg | PSC_SPICFG_DE_ENABLE;
- au_sync();
+ wmb(); /* drain writebuffer */
do {
stat = hw->regs->psc_spistat;
- au_sync();
+ wmb(); /* drain writebuffer */
} while ((stat & PSC_SPISTAT_DR) == 0);
if (hw->pdata->activate_cs)
@@ -252,9 +252,9 @@
au1550_spi_bits_handlers_set(hw, spi->bits_per_word);
cfg = hw->regs->psc_spicfg;
- au_sync();
+ wmb(); /* drain writebuffer */
hw->regs->psc_spicfg = cfg & ~PSC_SPICFG_DE_ENABLE;
- au_sync();
+ wmb(); /* drain writebuffer */
if (hw->usedma && bpw <= 8)
cfg &= ~PSC_SPICFG_DD_DISABLE;
@@ -268,12 +268,12 @@
cfg |= au1550_spi_baudcfg(hw, hz);
hw->regs->psc_spicfg = cfg;
- au_sync();
+ wmb(); /* drain writebuffer */
if (cfg & PSC_SPICFG_DE_ENABLE) {
do {
stat = hw->regs->psc_spistat;
- au_sync();
+ wmb(); /* drain writebuffer */
} while ((stat & PSC_SPISTAT_DR) == 0);
}
@@ -396,11 +396,11 @@
/* by default enable nearly all events interrupt */
hw->regs->psc_spimsk = PSC_SPIMSK_SD;
- au_sync();
+ wmb(); /* drain writebuffer */
/* start the transfer */
hw->regs->psc_spipcr = PSC_SPIPCR_MS;
- au_sync();
+ wmb(); /* drain writebuffer */
wait_for_completion(&hw->master_done);
@@ -429,7 +429,7 @@
stat = hw->regs->psc_spistat;
evnt = hw->regs->psc_spievent;
- au_sync();
+ wmb(); /* drain writebuffer */
if ((stat & PSC_SPISTAT_DI) == 0) {
dev_err(hw->dev, "Unexpected IRQ!\n");
return IRQ_NONE;
@@ -484,7 +484,7 @@
static void au1550_spi_rx_word_##size(struct au1550_spi *hw) \
{ \
u32 fifoword = hw->regs->psc_spitxrx & (u32)(mask); \
- au_sync(); \
+ wmb(); /* drain writebuffer */ \
if (hw->rx) { \
*(u##size *)hw->rx = (u##size)fifoword; \
hw->rx += (size) / 8; \
@@ -504,7 +504,7 @@
if (hw->tx_count >= hw->len) \
fifoword |= PSC_SPITXRX_LC; \
hw->regs->psc_spitxrx = fifoword; \
- au_sync(); \
+ wmb(); /* drain writebuffer */ \
}
AU1550_SPI_RX_WORD(8,0xff)
@@ -539,18 +539,18 @@
}
stat = hw->regs->psc_spistat;
- au_sync();
+ wmb(); /* drain writebuffer */
if (stat & PSC_SPISTAT_TF)
break;
}
/* enable event interrupts */
hw->regs->psc_spimsk = mask;
- au_sync();
+ wmb(); /* drain writebuffer */
/* start the transfer */
hw->regs->psc_spipcr = PSC_SPIPCR_MS;
- au_sync();
+ wmb(); /* drain writebuffer */
wait_for_completion(&hw->master_done);
@@ -564,7 +564,7 @@
stat = hw->regs->psc_spistat;
evnt = hw->regs->psc_spievent;
- au_sync();
+ wmb(); /* drain writebuffer */
if ((stat & PSC_SPISTAT_DI) == 0) {
dev_err(hw->dev, "Unexpected IRQ!\n");
return IRQ_NONE;
@@ -594,7 +594,7 @@
do {
busy = 0;
stat = hw->regs->psc_spistat;
- au_sync();
+ wmb(); /* drain writebuffer */
/*
* Take care to not let the Rx FIFO overflow.
@@ -615,7 +615,7 @@
} while (busy);
hw->regs->psc_spievent = PSC_SPIEVNT_RR | PSC_SPIEVNT_TR;
- au_sync();
+ wmb(); /* drain writebuffer */
/*
* Restart the SPI transmission in case of a transmit underflow.
@@ -634,9 +634,9 @@
*/
if (evnt & PSC_SPIEVNT_TU) {
hw->regs->psc_spievent = PSC_SPIEVNT_TU | PSC_SPIEVNT_MD;
- au_sync();
+ wmb(); /* drain writebuffer */
hw->regs->psc_spipcr = PSC_SPIPCR_MS;
- au_sync();
+ wmb(); /* drain writebuffer */
}
if (hw->rx_count >= hw->len) {
@@ -690,19 +690,19 @@
/* set up the PSC for SPI mode */
hw->regs->psc_ctrl = PSC_CTRL_DISABLE;
- au_sync();
+ wmb(); /* drain writebuffer */
hw->regs->psc_sel = PSC_SEL_PS_SPIMODE;
- au_sync();
+ wmb(); /* drain writebuffer */
hw->regs->psc_spicfg = 0;
- au_sync();
+ wmb(); /* drain writebuffer */
hw->regs->psc_ctrl = PSC_CTRL_ENABLE;
- au_sync();
+ wmb(); /* drain writebuffer */
do {
stat = hw->regs->psc_spistat;
- au_sync();
+ wmb(); /* drain writebuffer */
} while ((stat & PSC_SPISTAT_SR) == 0);
@@ -717,16 +717,16 @@
#endif
hw->regs->psc_spicfg = cfg;
- au_sync();
+ wmb(); /* drain writebuffer */
au1550_spi_mask_ack_all(hw);
hw->regs->psc_spicfg |= PSC_SPICFG_DE_ENABLE;
- au_sync();
+ wmb(); /* drain writebuffer */
do {
stat = hw->regs->psc_spistat;
- au_sync();
+ wmb(); /* drain writebuffer */
} while ((stat & PSC_SPISTAT_DR) == 0);
au1550_spi_reset_fifos(hw);
diff --git a/drivers/video/fbdev/au1100fb.c b/drivers/video/fbdev/au1100fb.c
index c0832ea..c163424 100644
--- a/drivers/video/fbdev/au1100fb.c
+++ b/drivers/video/fbdev/au1100fb.c
@@ -113,7 +113,7 @@
case VESA_NO_BLANKING:
/* Turn on panel */
fbdev->regs->lcd_control |= LCD_CONTROL_GO;
- au_sync();
+ wmb(); /* drain writebuffer */
break;
case VESA_VSYNC_SUSPEND:
@@ -121,7 +121,7 @@
case VESA_POWERDOWN:
/* Turn off panel */
fbdev->regs->lcd_control &= ~LCD_CONTROL_GO;
- au_sync();
+ wmb(); /* drain writebuffer */
break;
default:
break;
diff --git a/drivers/video/fbdev/au1200fb.c b/drivers/video/fbdev/au1200fb.c
index 2d77334..1c8e106 100644
--- a/drivers/video/fbdev/au1200fb.c
+++ b/drivers/video/fbdev/au1200fb.c
@@ -764,7 +764,7 @@
/* Disable the window while making changes, then restore WINEN */
winenable = lcd->winenable & (1 << plane);
- au_sync();
+ wmb(); /* drain writebuffer */
lcd->winenable &= ~(1 << plane);
lcd->window[plane].winctrl0 = winctrl0;
lcd->window[plane].winctrl1 = winctrl1;
@@ -772,7 +772,7 @@
lcd->window[plane].winbuf1 = fbdev->fb_phys;
lcd->window[plane].winbufctrl = 0; /* select winbuf0 */
lcd->winenable |= winenable;
- au_sync();
+ wmb(); /* drain writebuffer */
return 0;
}
@@ -788,22 +788,21 @@
/* Make sure all windows disabled */
winenable = lcd->winenable;
lcd->winenable = 0;
- au_sync();
+ wmb(); /* drain writebuffer */
/*
* Ensure everything is disabled before reconfiguring
*/
if (lcd->screen & LCD_SCREEN_SEN) {
/* Wait for vertical sync period */
lcd->intstatus = LCD_INT_SS;
- while ((lcd->intstatus & LCD_INT_SS) == 0) {
- au_sync();
- }
+ while ((lcd->intstatus & LCD_INT_SS) == 0)
+ ;
lcd->screen &= ~LCD_SCREEN_SEN; /*disable the controller*/
do {
lcd->intstatus = lcd->intstatus; /*clear interrupts*/
- au_sync();
+ wmb(); /* drain writebuffer */
/*wait for controller to shut down*/
} while ((lcd->intstatus & LCD_INT_SD) == 0);
@@ -847,7 +846,7 @@
lcd->pwmhi = panel->mode_pwmhi;
lcd->outmask = panel->mode_outmask;
lcd->fifoctrl = panel->mode_fifoctrl;
- au_sync();
+ wmb(); /* drain writebuffer */
/* fixme: Check window settings to make sure still valid
* for new geometry */
@@ -863,7 +862,7 @@
* Re-enable screen now that it is configured
*/
lcd->screen |= LCD_SCREEN_SEN;
- au_sync();
+ wmb(); /* drain writebuffer */
/* Call init of panel */
if (pd->panel_init)
@@ -956,7 +955,7 @@
| LCD_WINCTRL2_SCY_1
) ;
lcd->winenable |= win->w[plane].mode_winenable;
- au_sync();
+ wmb(); /* drain writebuffer */
}
@@ -1270,7 +1269,7 @@
if (pdata->flags & SCREEN_MASK)
lcd->colorkeymsk = pdata->mask;
- au_sync();
+ wmb(); /* drain writebuffer */
}
static void get_global(u_int cmd, struct au1200_lcd_global_regs_t *pdata)
@@ -1288,7 +1287,7 @@
hi1 = (lcd->pwmhi >> 16) + 1;
divider = (lcd->pwmdiv & 0x3FFFF) + 1;
pdata->brightness = ((hi1 << 8) / divider) - 1;
- au_sync();
+ wmb(); /* drain writebuffer */
}
static void set_window(unsigned int plane,
@@ -1387,7 +1386,7 @@
val |= (pdata->enable & 1) << plane;
lcd->winenable = val;
}
- au_sync();
+ wmb(); /* drain writebuffer */
}
static void get_window(unsigned int plane,
@@ -1414,7 +1413,7 @@
pdata->ram_array_mode = (lcd->window[plane].winctrl2 & LCD_WINCTRL2_RAM) >> 21;
pdata->enable = (lcd->winenable >> plane) & 1;
- au_sync();
+ wmb(); /* drain writebuffer */
}
static int au1200fb_ioctl(struct fb_info *info, unsigned int cmd,
@@ -1511,7 +1510,7 @@
{
/* Nothing to do for now, just clear any pending interrupt */
lcd->intstatus = lcd->intstatus;
- au_sync();
+ wmb(); /* drain writebuffer */
return IRQ_HANDLED;
}
@@ -1809,7 +1808,7 @@
au1200_setpanel(NULL, pd);
lcd->outmask = 0;
- au_sync();
+ wmb(); /* drain writebuffer */
return 0;
}