mfd: Avoid twl6040-codec PLL reconfiguration when not needed
Do not reconfigure the PLL in case it has been configured already
with the requested parameters.
In case of different PLL configuration do only the needed changes.
This can save considerable amount of time since we can avoid the
defined protocol (with delays) for the PLL configuration.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
diff --git a/drivers/mfd/twl6040-core.c b/drivers/mfd/twl6040-core.c
index c2088f4..b2d8e51 100644
--- a/drivers/mfd/twl6040-core.c
+++ b/drivers/mfd/twl6040-core.c
@@ -326,23 +326,38 @@
hppllctl = twl6040_reg_read(twl6040, TWL6040_REG_HPPLLCTL);
lppllctl = twl6040_reg_read(twl6040, TWL6040_REG_LPPLLCTL);
+ /* Force full reconfiguration when switching between PLL */
+ if (pll_id != twl6040->pll) {
+ twl6040->sysclk = 0;
+ twl6040->mclk = 0;
+ }
+
switch (pll_id) {
case TWL6040_SYSCLK_SEL_LPPLL:
/* low-power PLL divider */
- switch (freq_out) {
- case 17640000:
- lppllctl |= TWL6040_LPLLFIN;
- break;
- case 19200000:
- lppllctl &= ~TWL6040_LPLLFIN;
- break;
- default:
- dev_err(twl6040->dev,
- "freq_out %d not supported\n", freq_out);
- ret = -EINVAL;
- goto pll_out;
+ /* Change the sysclk configuration only if it has been canged */
+ if (twl6040->sysclk != freq_out) {
+ switch (freq_out) {
+ case 17640000:
+ lppllctl |= TWL6040_LPLLFIN;
+ break;
+ case 19200000:
+ lppllctl &= ~TWL6040_LPLLFIN;
+ break;
+ default:
+ dev_err(twl6040->dev,
+ "freq_out %d not supported\n",
+ freq_out);
+ ret = -EINVAL;
+ goto pll_out;
+ }
+ twl6040_reg_write(twl6040, TWL6040_REG_LPPLLCTL,
+ lppllctl);
}
- twl6040_reg_write(twl6040, TWL6040_REG_LPPLLCTL, lppllctl);
+
+ /* The PLL in use has not been change, we can exit */
+ if (twl6040->pll == pll_id)
+ break;
switch (freq_in) {
case 32768:
@@ -373,48 +388,56 @@
goto pll_out;
}
- hppllctl &= ~TWL6040_MCLK_MSK;
+ if (twl6040->mclk != freq_in) {
+ hppllctl &= ~TWL6040_MCLK_MSK;
- switch (freq_in) {
- case 12000000:
- /* PLL enabled, active mode */
- hppllctl |= TWL6040_MCLK_12000KHZ |
- TWL6040_HPLLENA;
- break;
- case 19200000:
+ switch (freq_in) {
+ case 12000000:
+ /* PLL enabled, active mode */
+ hppllctl |= TWL6040_MCLK_12000KHZ |
+ TWL6040_HPLLENA;
+ break;
+ case 19200000:
+ /*
+ * PLL disabled
+ * (enable PLL if MCLK jitter quality
+ * doesn't meet specification)
+ */
+ hppllctl |= TWL6040_MCLK_19200KHZ;
+ break;
+ case 26000000:
+ /* PLL enabled, active mode */
+ hppllctl |= TWL6040_MCLK_26000KHZ |
+ TWL6040_HPLLENA;
+ break;
+ case 38400000:
+ /* PLL enabled, active mode */
+ hppllctl |= TWL6040_MCLK_38400KHZ |
+ TWL6040_HPLLENA;
+ break;
+ default:
+ dev_err(twl6040->dev,
+ "freq_in %d not supported\n", freq_in);
+ ret = -EINVAL;
+ goto pll_out;
+ }
+
/*
- * PLL disabled
- * (enable PLL if MCLK jitter quality
- * doesn't meet specification)
+ * enable clock slicer to ensure input waveform is
+ * square
*/
- hppllctl |= TWL6040_MCLK_19200KHZ;
- break;
- case 26000000:
- /* PLL enabled, active mode */
- hppllctl |= TWL6040_MCLK_26000KHZ |
- TWL6040_HPLLENA;
- break;
- case 38400000:
- /* PLL enabled, active mode */
- hppllctl |= TWL6040_MCLK_38400KHZ |
- TWL6040_HPLLENA;
- break;
- default:
- dev_err(twl6040->dev,
- "freq_in %d not supported\n", freq_in);
- ret = -EINVAL;
- goto pll_out;
+ hppllctl |= TWL6040_HPLLSQRENA;
+
+ twl6040_reg_write(twl6040, TWL6040_REG_HPPLLCTL,
+ hppllctl);
+ usleep_range(500, 700);
+ lppllctl |= TWL6040_HPLLSEL;
+ twl6040_reg_write(twl6040, TWL6040_REG_LPPLLCTL,
+ lppllctl);
+ lppllctl &= ~TWL6040_LPLLENA;
+ twl6040_reg_write(twl6040, TWL6040_REG_LPPLLCTL,
+ lppllctl);
}
-
- /* enable clock slicer to ensure input waveform is square */
- hppllctl |= TWL6040_HPLLSQRENA;
-
- twl6040_reg_write(twl6040, TWL6040_REG_HPPLLCTL, hppllctl);
- usleep_range(500, 700);
- lppllctl |= TWL6040_HPLLSEL;
- twl6040_reg_write(twl6040, TWL6040_REG_LPPLLCTL, lppllctl);
- lppllctl &= ~TWL6040_LPLLENA;
- twl6040_reg_write(twl6040, TWL6040_REG_LPPLLCTL, lppllctl);
break;
default:
dev_err(twl6040->dev, "unknown pll id %d\n", pll_id);