drm: adv7511: it's HPD, not HDP
Fix this typo, consequently used over both files :)
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Archit Taneja <architt@codeaurora.org>
diff --git a/drivers/gpu/drm/i2c/adv7511.c b/drivers/gpu/drm/i2c/adv7511.c
index e1756a4..a02112b 100644
--- a/drivers/gpu/drm/i2c/adv7511.c
+++ b/drivers/gpu/drm/i2c/adv7511.c
@@ -378,16 +378,16 @@
}
/*
- * Per spec it is allowed to pulse the HDP signal to indicate that the
+ * Per spec it is allowed to pulse the HPD signal to indicate that the
* EDID information has changed. Some monitors do this when they wakeup
- * from standby or are enabled. When the HDP goes low the adv7511 is
+ * from standby or are enabled. When the HPD goes low the adv7511 is
* reset and the outputs are disabled which might cause the monitor to
- * go to standby again. To avoid this we ignore the HDP pin for the
+ * go to standby again. To avoid this we ignore the HPD pin for the
* first few seconds after enabling the output.
*/
regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
- ADV7511_REG_POWER2_HDP_SRC_MASK,
- ADV7511_REG_POWER2_HDP_SRC_NONE);
+ ADV7511_REG_POWER2_HPD_SRC_MASK,
+ ADV7511_REG_POWER2_HPD_SRC_NONE);
/*
* Most of the registers are reset during power down or when HPD is low.
@@ -421,9 +421,9 @@
if (ret < 0)
return false;
- if (irq0 & ADV7511_INT0_HDP) {
+ if (irq0 & ADV7511_INT0_HPD) {
regmap_write(adv7511->regmap, ADV7511_REG_INT(0),
- ADV7511_INT0_HDP);
+ ADV7511_INT0_HPD);
return true;
}
@@ -446,7 +446,7 @@
regmap_write(adv7511->regmap, ADV7511_REG_INT(0), irq0);
regmap_write(adv7511->regmap, ADV7511_REG_INT(1), irq1);
- if (irq0 & ADV7511_INT0_HDP && adv7511->encoder)
+ if (irq0 & ADV7511_INT0_HPD && adv7511->encoder)
drm_helper_hpd_irq_event(adv7511->encoder->dev);
if (irq0 & ADV7511_INT0_EDID_READY || irq1 & ADV7511_INT1_DDC_ERROR) {
@@ -648,10 +648,10 @@
if (adv7511->status == connector_status_connected)
status = connector_status_disconnected;
} else {
- /* Renable HDP sensing */
+ /* Renable HPD sensing */
regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
- ADV7511_REG_POWER2_HDP_SRC_MASK,
- ADV7511_REG_POWER2_HDP_SRC_BOTH);
+ ADV7511_REG_POWER2_HPD_SRC_MASK,
+ ADV7511_REG_POWER2_HPD_SRC_BOTH);
}
adv7511->status = status;