Auto-update from upstream
diff --git a/Documentation/networking/phy.txt b/Documentation/networking/phy.txt
new file mode 100644
index 0000000..29ccae4
--- /dev/null
+++ b/Documentation/networking/phy.txt
@@ -0,0 +1,288 @@
+
+-------
+PHY Abstraction Layer
+(Updated 2005-07-21)
+
+Purpose
+
+ Most network devices consist of set of registers which provide an interface
+ to a MAC layer, which communicates with the physical connection through a
+ PHY. The PHY concerns itself with negotiating link parameters with the link
+ partner on the other side of the network connection (typically, an ethernet
+ cable), and provides a register interface to allow drivers to determine what
+ settings were chosen, and to configure what settings are allowed.
+
+ While these devices are distinct from the network devices, and conform to a
+ standard layout for the registers, it has been common practice to integrate
+ the PHY management code with the network driver. This has resulted in large
+ amounts of redundant code. Also, on embedded systems with multiple (and
+ sometimes quite different) ethernet controllers connected to the same
+ management bus, it is difficult to ensure safe use of the bus.
+
+ Since the PHYs are devices, and the management busses through which they are
+ accessed are, in fact, busses, the PHY Abstraction Layer treats them as such.
+ In doing so, it has these goals:
+
+ 1) Increase code-reuse
+ 2) Increase overall code-maintainability
+ 3) Speed development time for new network drivers, and for new systems
+
+ Basically, this layer is meant to provide an interface to PHY devices which
+ allows network driver writers to write as little code as possible, while
+ still providing a full feature set.
+
+The MDIO bus
+
+ Most network devices are connected to a PHY by means of a management bus.
+ Different devices use different busses (though some share common interfaces).
+ In order to take advantage of the PAL, each bus interface needs to be
+ registered as a distinct device.
+
+ 1) read and write functions must be implemented. Their prototypes are:
+
+ int write(struct mii_bus *bus, int mii_id, int regnum, u16 value);
+ int read(struct mii_bus *bus, int mii_id, int regnum);
+
+ mii_id is the address on the bus for the PHY, and regnum is the register
+ number. These functions are guaranteed not to be called from interrupt
+ time, so it is safe for them to block, waiting for an interrupt to signal
+ the operation is complete
+
+ 2) A reset function is necessary. This is used to return the bus to an
+ initialized state.
+
+ 3) A probe function is needed. This function should set up anything the bus
+ driver needs, setup the mii_bus structure, and register with the PAL using
+ mdiobus_register. Similarly, there's a remove function to undo all of
+ that (use mdiobus_unregister).
+
+ 4) Like any driver, the device_driver structure must be configured, and init
+ exit functions are used to register the driver.
+
+ 5) The bus must also be declared somewhere as a device, and registered.
+
+ As an example for how one driver implemented an mdio bus driver, see
+ drivers/net/gianfar_mii.c and arch/ppc/syslib/mpc85xx_devices.c
+
+Connecting to a PHY
+
+ Sometime during startup, the network driver needs to establish a connection
+ between the PHY device, and the network device. At this time, the PHY's bus
+ and drivers need to all have been loaded, so it is ready for the connection.
+ At this point, there are several ways to connect to the PHY:
+
+ 1) The PAL handles everything, and only calls the network driver when
+ the link state changes, so it can react.
+
+ 2) The PAL handles everything except interrupts (usually because the
+ controller has the interrupt registers).
+
+ 3) The PAL handles everything, but checks in with the driver every second,
+ allowing the network driver to react first to any changes before the PAL
+ does.
+
+ 4) The PAL serves only as a library of functions, with the network device
+ manually calling functions to update status, and configure the PHY
+
+
+Letting the PHY Abstraction Layer do Everything
+
+ If you choose option 1 (The hope is that every driver can, but to still be
+ useful to drivers that can't), connecting to the PHY is simple:
+
+ First, you need a function to react to changes in the link state. This
+ function follows this protocol:
+
+ static void adjust_link(struct net_device *dev);
+
+ Next, you need to know the device name of the PHY connected to this device.
+ The name will look something like, "phy0:0", where the first number is the
+ bus id, and the second is the PHY's address on that bus.
+
+ Now, to connect, just call this function:
+
+ phydev = phy_connect(dev, phy_name, &adjust_link, flags);
+
+ phydev is a pointer to the phy_device structure which represents the PHY. If
+ phy_connect is successful, it will return the pointer. dev, here, is the
+ pointer to your net_device. Once done, this function will have started the
+ PHY's software state machine, and registered for the PHY's interrupt, if it
+ has one. The phydev structure will be populated with information about the
+ current state, though the PHY will not yet be truly operational at this
+ point.
+
+ flags is a u32 which can optionally contain phy-specific flags.
+ This is useful if the system has put hardware restrictions on
+ the PHY/controller, of which the PHY needs to be aware.
+
+ Now just make sure that phydev->supported and phydev->advertising have any
+ values pruned from them which don't make sense for your controller (a 10/100
+ controller may be connected to a gigabit capable PHY, so you would need to
+ mask off SUPPORTED_1000baseT*). See include/linux/ethtool.h for definitions
+ for these bitfields. Note that you should not SET any bits, or the PHY may
+ get put into an unsupported state.
+
+ Lastly, once the controller is ready to handle network traffic, you call
+ phy_start(phydev). This tells the PAL that you are ready, and configures the
+ PHY to connect to the network. If you want to handle your own interrupts,
+ just set phydev->irq to PHY_IGNORE_INTERRUPT before you call phy_start.
+ Similarly, if you don't want to use interrupts, set phydev->irq to PHY_POLL.
+
+ When you want to disconnect from the network (even if just briefly), you call
+ phy_stop(phydev).
+
+Keeping Close Tabs on the PAL
+
+ It is possible that the PAL's built-in state machine needs a little help to
+ keep your network device and the PHY properly in sync. If so, you can
+ register a helper function when connecting to the PHY, which will be called
+ every second before the state machine reacts to any changes. To do this, you
+ need to manually call phy_attach() and phy_prepare_link(), and then call
+ phy_start_machine() with the second argument set to point to your special
+ handler.
+
+ Currently there are no examples of how to use this functionality, and testing
+ on it has been limited because the author does not have any drivers which use
+ it (they all use option 1). So Caveat Emptor.
+
+Doing it all yourself
+
+ There's a remote chance that the PAL's built-in state machine cannot track
+ the complex interactions between the PHY and your network device. If this is
+ so, you can simply call phy_attach(), and not call phy_start_machine or
+ phy_prepare_link(). This will mean that phydev->state is entirely yours to
+ handle (phy_start and phy_stop toggle between some of the states, so you
+ might need to avoid them).
+
+ An effort has been made to make sure that useful functionality can be
+ accessed without the state-machine running, and most of these functions are
+ descended from functions which did not interact with a complex state-machine.
+ However, again, no effort has been made so far to test running without the
+ state machine, so tryer beware.
+
+ Here is a brief rundown of the functions:
+
+ int phy_read(struct phy_device *phydev, u16 regnum);
+ int phy_write(struct phy_device *phydev, u16 regnum, u16 val);
+
+ Simple read/write primitives. They invoke the bus's read/write function
+ pointers.
+
+ void phy_print_status(struct phy_device *phydev);
+
+ A convenience function to print out the PHY status neatly.
+
+ int phy_clear_interrupt(struct phy_device *phydev);
+ int phy_config_interrupt(struct phy_device *phydev, u32 interrupts);
+
+ Clear the PHY's interrupt, and configure which ones are allowed,
+ respectively. Currently only supports all on, or all off.
+
+ int phy_enable_interrupts(struct phy_device *phydev);
+ int phy_disable_interrupts(struct phy_device *phydev);
+
+ Functions which enable/disable PHY interrupts, clearing them
+ before and after, respectively.
+
+ int phy_start_interrupts(struct phy_device *phydev);
+ int phy_stop_interrupts(struct phy_device *phydev);
+
+ Requests the IRQ for the PHY interrupts, then enables them for
+ start, or disables then frees them for stop.
+
+ struct phy_device * phy_attach(struct net_device *dev, const char *phy_id,
+ u32 flags);
+
+ Attaches a network device to a particular PHY, binding the PHY to a generic
+ driver if none was found during bus initialization. Passes in
+ any phy-specific flags as needed.
+
+ int phy_start_aneg(struct phy_device *phydev);
+
+ Using variables inside the phydev structure, either configures advertising
+ and resets autonegotiation, or disables autonegotiation, and configures
+ forced settings.
+
+ static inline int phy_read_status(struct phy_device *phydev);
+
+ Fills the phydev structure with up-to-date information about the current
+ settings in the PHY.
+
+ void phy_sanitize_settings(struct phy_device *phydev)
+
+ Resolves differences between currently desired settings, and
+ supported settings for the given PHY device. Does not make
+ the changes in the hardware, though.
+
+ int phy_ethtool_sset(struct phy_device *phydev, struct ethtool_cmd *cmd);
+ int phy_ethtool_gset(struct phy_device *phydev, struct ethtool_cmd *cmd);
+
+ Ethtool convenience functions.
+
+ int phy_mii_ioctl(struct phy_device *phydev,
+ struct mii_ioctl_data *mii_data, int cmd);
+
+ The MII ioctl. Note that this function will completely screw up the state
+ machine if you write registers like BMCR, BMSR, ADVERTISE, etc. Best to
+ use this only to write registers which are not standard, and don't set off
+ a renegotiation.
+
+
+PHY Device Drivers
+
+ With the PHY Abstraction Layer, adding support for new PHYs is
+ quite easy. In some cases, no work is required at all! However,
+ many PHYs require a little hand-holding to get up-and-running.
+
+Generic PHY driver
+
+ If the desired PHY doesn't have any errata, quirks, or special
+ features you want to support, then it may be best to not add
+ support, and let the PHY Abstraction Layer's Generic PHY Driver
+ do all of the work.
+
+Writing a PHY driver
+
+ If you do need to write a PHY driver, the first thing to do is
+ make sure it can be matched with an appropriate PHY device.
+ This is done during bus initialization by reading the device's
+ UID (stored in registers 2 and 3), then comparing it to each
+ driver's phy_id field by ANDing it with each driver's
+ phy_id_mask field. Also, it needs a name. Here's an example:
+
+ static struct phy_driver dm9161_driver = {
+ .phy_id = 0x0181b880,
+ .name = "Davicom DM9161E",
+ .phy_id_mask = 0x0ffffff0,
+ ...
+ }
+
+ Next, you need to specify what features (speed, duplex, autoneg,
+ etc) your PHY device and driver support. Most PHYs support
+ PHY_BASIC_FEATURES, but you can look in include/mii.h for other
+ features.
+
+ Each driver consists of a number of function pointers:
+
+ config_init: configures PHY into a sane state after a reset.
+ For instance, a Davicom PHY requires descrambling disabled.
+ probe: Does any setup needed by the driver
+ suspend/resume: power management
+ config_aneg: Changes the speed/duplex/negotiation settings
+ read_status: Reads the current speed/duplex/negotiation settings
+ ack_interrupt: Clear a pending interrupt
+ config_intr: Enable or disable interrupts
+ remove: Does any driver take-down
+
+ Of these, only config_aneg and read_status are required to be
+ assigned by the driver code. The rest are optional. Also, it is
+ preferred to use the generic phy driver's versions of these two
+ functions if at all possible: genphy_read_status and
+ genphy_config_aneg. If this is not possible, it is likely that
+ you only need to perform some actions before and after invoking
+ these functions, and so your functions will wrap the generic
+ ones.
+
+ Feel free to look at the Marvell, Cicada, and Davicom drivers in
+ drivers/net/phy/ for examples (the lxt and qsemi drivers have
+ not been tested as of this writing)
diff --git a/Makefile b/Makefile
index 300f61f..3d84df5 100644
--- a/Makefile
+++ b/Makefile
@@ -1,8 +1,8 @@
VERSION = 2
PATCHLEVEL = 6
SUBLEVEL = 13
-EXTRAVERSION =-rc7
-NAME=Woozy Numbat
+EXTRAVERSION =
+NAME=Affluent Albatross
# *DOCUMENTATION*
# To see a list of typical targets execute "make help"
diff --git a/arch/alpha/kernel/signal.c b/arch/alpha/kernel/signal.c
index 08fe807..2e45e86 100644
--- a/arch/alpha/kernel/signal.c
+++ b/arch/alpha/kernel/signal.c
@@ -566,13 +566,12 @@
if (ka->sa.sa_flags & SA_RESETHAND)
ka->sa.sa_handler = SIG_DFL;
- if (!(ka->sa.sa_flags & SA_NODEFER)) {
- spin_lock_irq(¤t->sighand->siglock);
- sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ spin_lock_irq(¤t->sighand->siglock);
+ sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ if (!(ka->sa.sa_flags & SA_NODEFER))
sigaddset(¤t->blocked,sig);
- recalc_sigpending();
- spin_unlock_irq(¤t->sighand->siglock);
- }
+ recalc_sigpending();
+ spin_unlock_irq(¤t->sighand->siglock);
}
static inline void
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index c65c6eb..4bf0e87 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -635,10 +635,6 @@
and the Battery Powered Linux mini-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
- Note that, even if you say N here, Linux on the x86 architecture
- will issue the hlt instruction if nothing is to be done, thereby
- sending the processor to sleep and saving power.
-
config APM
tristate "Advanced Power Management Emulation"
depends on PM
@@ -650,12 +646,6 @@
battery status information, and user-space programs will receive
notification of APM "events" (e.g. battery status change).
- If you select "Y" here, you can disable actual use of the APM
- BIOS by passing the "apm=off" option to the kernel at boot time.
-
- Note that the APM support is almost completely disabled for
- machines with more than one CPU.
-
In order to use APM, you will need supporting software. For location
and more information, read <file:Documentation/pm.txt> and the
Battery Powered Linux mini-HOWTO, available from
@@ -665,39 +655,12 @@
manpage ("man 8 hdparm") for that), and it doesn't turn off
VESA-compliant "green" monitors.
- This driver does not support the TI 4000M TravelMate and the ACER
- 486/DX4/75 because they don't have compliant BIOSes. Many "green"
- desktop machines also don't have compliant BIOSes, and this driver
- may cause those machines to panic during the boot phase.
-
Generally, if you don't have a battery in your machine, there isn't
much point in using this driver and you should say N. If you get
random kernel OOPSes or reboots that don't seem to be related to
anything, try disabling/enabling this option (or disabling/enabling
APM in your BIOS).
- Some other things you should try when experiencing seemingly random,
- "weird" problems:
-
- 1) make sure that you have enough swap space and that it is
- enabled.
- 2) pass the "no-hlt" option to the kernel
- 3) switch on floating point emulation in the kernel and pass
- the "no387" option to the kernel
- 4) pass the "floppy=nodma" option to the kernel
- 5) pass the "mem=4M" option to the kernel (thereby disabling
- all but the first 4 MB of RAM)
- 6) make sure that the CPU is not over clocked.
- 7) read the sig11 FAQ at <http://www.bitwizard.nl/sig11/>
- 8) disable the cache from your BIOS settings
- 9) install a fan for the video card or exchange video RAM
- 10) install a better fan for the CPU
- 11) exchange RAM chips
- 12) exchange the motherboard.
-
- To compile this driver as a module, choose M here: the
- module will be called apm.
-
endmenu
source "net/Kconfig"
@@ -752,6 +715,8 @@
source "drivers/misc/Kconfig"
+source "drivers/mfd/Kconfig"
+
source "drivers/media/Kconfig"
source "drivers/video/Kconfig"
diff --git a/arch/arm/common/Kconfig b/arch/arm/common/Kconfig
index 692af6b..666ba39 100644
--- a/arch/arm/common/Kconfig
+++ b/arch/arm/common/Kconfig
@@ -1,6 +1,9 @@
config ICST525
bool
+config ARM_GIC
+ bool
+
config ICST307
bool
diff --git a/arch/arm/common/Makefile b/arch/arm/common/Makefile
index 11f20a4..a878865 100644
--- a/arch/arm/common/Makefile
+++ b/arch/arm/common/Makefile
@@ -4,6 +4,7 @@
obj-y += rtctime.o
obj-$(CONFIG_ARM_AMBA) += amba.o
+obj-$(CONFIG_ARM_GIC) += gic.o
obj-$(CONFIG_ICST525) += icst525.o
obj-$(CONFIG_ICST307) += icst307.o
obj-$(CONFIG_SA1111) += sa1111.o
diff --git a/arch/arm/common/gic.c b/arch/arm/common/gic.c
new file mode 100644
index 0000000..51dbf54
--- /dev/null
+++ b/arch/arm/common/gic.c
@@ -0,0 +1,166 @@
+/*
+ * linux/arch/arm/common/gic.c
+ *
+ * Copyright (C) 2002 ARM Limited, All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * Interrupt architecture for the GIC:
+ *
+ * o There is one Interrupt Distributor, which receives interrupts
+ * from system devices and sends them to the Interrupt Controllers.
+ *
+ * o There is one CPU Interface per CPU, which sends interrupts sent
+ * by the Distributor, and interrupts generated locally, to the
+ * associated CPU.
+ *
+ * Note that IRQs 0-31 are special - they are local to each CPU.
+ * As such, the enable set/clear, pending set/clear and active bit
+ * registers are banked per-cpu for these sources.
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/list.h>
+#include <linux/smp.h>
+
+#include <asm/irq.h>
+#include <asm/io.h>
+#include <asm/mach/irq.h>
+#include <asm/hardware/gic.h>
+
+static void __iomem *gic_dist_base;
+static void __iomem *gic_cpu_base;
+
+/*
+ * Routines to acknowledge, disable and enable interrupts
+ *
+ * Linux assumes that when we're done with an interrupt we need to
+ * unmask it, in the same way we need to unmask an interrupt when
+ * we first enable it.
+ *
+ * The GIC has a seperate notion of "end of interrupt" to re-enable
+ * an interrupt after handling, in order to support hardware
+ * prioritisation.
+ *
+ * We can make the GIC behave in the way that Linux expects by making
+ * our "acknowledge" routine disable the interrupt, then mark it as
+ * complete.
+ */
+static void gic_ack_irq(unsigned int irq)
+{
+ u32 mask = 1 << (irq % 32);
+ writel(mask, gic_dist_base + GIC_DIST_ENABLE_CLEAR + (irq / 32) * 4);
+ writel(irq, gic_cpu_base + GIC_CPU_EOI);
+}
+
+static void gic_mask_irq(unsigned int irq)
+{
+ u32 mask = 1 << (irq % 32);
+ writel(mask, gic_dist_base + GIC_DIST_ENABLE_CLEAR + (irq / 32) * 4);
+}
+
+static void gic_unmask_irq(unsigned int irq)
+{
+ u32 mask = 1 << (irq % 32);
+ writel(mask, gic_dist_base + GIC_DIST_ENABLE_SET + (irq / 32) * 4);
+}
+
+static void gic_set_cpu(struct irqdesc *desc, unsigned int irq, unsigned int cpu)
+{
+ void __iomem *reg = gic_dist_base + GIC_DIST_TARGET + (irq & ~3);
+ unsigned int shift = (irq % 4) * 8;
+ u32 val;
+
+ val = readl(reg) & ~(0xff << shift);
+ val |= 1 << (cpu + shift);
+ writel(val, reg);
+}
+
+static struct irqchip gic_chip = {
+ .ack = gic_ack_irq,
+ .mask = gic_mask_irq,
+ .unmask = gic_unmask_irq,
+#ifdef CONFIG_SMP
+ .set_cpu = gic_set_cpu,
+#endif
+};
+
+void __init gic_dist_init(void __iomem *base)
+{
+ unsigned int max_irq, i;
+ u32 cpumask = 1 << smp_processor_id();
+
+ cpumask |= cpumask << 8;
+ cpumask |= cpumask << 16;
+
+ gic_dist_base = base;
+
+ writel(0, base + GIC_DIST_CTRL);
+
+ /*
+ * Find out how many interrupts are supported.
+ */
+ max_irq = readl(base + GIC_DIST_CTR) & 0x1f;
+ max_irq = (max_irq + 1) * 32;
+
+ /*
+ * The GIC only supports up to 1020 interrupt sources.
+ * Limit this to either the architected maximum, or the
+ * platform maximum.
+ */
+ if (max_irq > max(1020, NR_IRQS))
+ max_irq = max(1020, NR_IRQS);
+
+ /*
+ * Set all global interrupts to be level triggered, active low.
+ */
+ for (i = 32; i < max_irq; i += 16)
+ writel(0, base + GIC_DIST_CONFIG + i * 4 / 16);
+
+ /*
+ * Set all global interrupts to this CPU only.
+ */
+ for (i = 32; i < max_irq; i += 4)
+ writel(cpumask, base + GIC_DIST_TARGET + i * 4 / 4);
+
+ /*
+ * Set priority on all interrupts.
+ */
+ for (i = 0; i < max_irq; i += 4)
+ writel(0xa0a0a0a0, base + GIC_DIST_PRI + i * 4 / 4);
+
+ /*
+ * Disable all interrupts.
+ */
+ for (i = 0; i < max_irq; i += 32)
+ writel(0xffffffff, base + GIC_DIST_ENABLE_CLEAR + i * 4 / 32);
+
+ /*
+ * Setup the Linux IRQ subsystem.
+ */
+ for (i = 29; i < max_irq; i++) {
+ set_irq_chip(i, &gic_chip);
+ set_irq_handler(i, do_level_IRQ);
+ set_irq_flags(i, IRQF_VALID | IRQF_PROBE);
+ }
+
+ writel(1, base + GIC_DIST_CTRL);
+}
+
+void __cpuinit gic_cpu_init(void __iomem *base)
+{
+ gic_cpu_base = base;
+ writel(0xf0, base + GIC_CPU_PRIMASK);
+ writel(1, base + GIC_CPU_CTRL);
+}
+
+#ifdef CONFIG_SMP
+void gic_raise_softirq(cpumask_t cpumask, unsigned int irq)
+{
+ unsigned long map = *cpus_addr(cpumask);
+
+ writel(map << 16 | irq, gic_dist_base + GIC_DIST_SOFTINT);
+}
+#endif
diff --git a/arch/arm/kernel/signal.c b/arch/arm/kernel/signal.c
index 5e435e4..a94d75f 100644
--- a/arch/arm/kernel/signal.c
+++ b/arch/arm/kernel/signal.c
@@ -658,11 +658,12 @@
/*
* Block the signal if we were unsuccessful.
*/
- if (ret != 0 || !(ka->sa.sa_flags & SA_NODEFER)) {
+ if (ret != 0) {
spin_lock_irq(&tsk->sighand->siglock);
sigorsets(&tsk->blocked, &tsk->blocked,
&ka->sa.sa_mask);
- sigaddset(&tsk->blocked, sig);
+ if (!(ka->sa.sa_flags & SA_NODEFER))
+ sigaddset(&tsk->blocked, sig);
recalc_sigpending();
spin_unlock_irq(&tsk->sighand->siglock);
}
diff --git a/arch/arm/mach-ixp4xx/coyote-setup.c b/arch/arm/mach-ixp4xx/coyote-setup.c
index 7f58afb..411ea99 100644
--- a/arch/arm/mach-ixp4xx/coyote-setup.c
+++ b/arch/arm/mach-ixp4xx/coyote-setup.c
@@ -36,7 +36,7 @@
static struct resource coyote_flash_resource = {
.start = COYOTE_FLASH_BASE,
- .end = COYOTE_FLASH_BASE + COYOTE_FLASH_SIZE,
+ .end = COYOTE_FLASH_BASE + COYOTE_FLASH_SIZE - 1,
.flags = IORESOURCE_MEM,
};
diff --git a/arch/arm/mach-ixp4xx/gtwx5715-setup.c b/arch/arm/mach-ixp4xx/gtwx5715-setup.c
index 65e356b..333459d 100644
--- a/arch/arm/mach-ixp4xx/gtwx5715-setup.c
+++ b/arch/arm/mach-ixp4xx/gtwx5715-setup.c
@@ -114,7 +114,7 @@
static struct resource gtwx5715_flash_resource = {
.start = GTWX5715_FLASH_BASE,
- .end = GTWX5715_FLASH_BASE + GTWX5715_FLASH_SIZE,
+ .end = GTWX5715_FLASH_BASE + GTWX5715_FLASH_SIZE - 1,
.flags = IORESOURCE_MEM,
};
diff --git a/arch/arm/mach-ixp4xx/ixdp425-setup.c b/arch/arm/mach-ixp4xx/ixdp425-setup.c
index 4633470..fa0646c 100644
--- a/arch/arm/mach-ixp4xx/ixdp425-setup.c
+++ b/arch/arm/mach-ixp4xx/ixdp425-setup.c
@@ -36,7 +36,7 @@
static struct resource ixdp425_flash_resource = {
.start = IXDP425_FLASH_BASE,
- .end = IXDP425_FLASH_BASE + IXDP425_FLASH_SIZE,
+ .end = IXDP425_FLASH_BASE + IXDP425_FLASH_SIZE - 1,
.flags = IORESOURCE_MEM,
};
diff --git a/arch/arm/mach-sa1100/assabet.c b/arch/arm/mach-sa1100/assabet.c
index 4d4d303..24687f5 100644
--- a/arch/arm/mach-sa1100/assabet.c
+++ b/arch/arm/mach-sa1100/assabet.c
@@ -35,6 +35,7 @@
#include <asm/mach/map.h>
#include <asm/mach/serial_sa1100.h>
#include <asm/arch/assabet.h>
+#include <asm/arch/mcp.h>
#include "generic.h"
@@ -198,6 +199,11 @@
.set_speed = assabet_irda_set_speed,
};
+static struct mcp_plat_data assabet_mcp_data = {
+ .mccr0 = MCCR0_ADM,
+ .sclk_rate = 11981000,
+};
+
static void __init assabet_init(void)
{
/*
@@ -246,6 +252,7 @@
sa11x0_set_flash_data(&assabet_flash_data, assabet_flash_resources,
ARRAY_SIZE(assabet_flash_resources));
sa11x0_set_irda_data(&assabet_irda_data);
+ sa11x0_set_mcp_data(&assabet_mcp_data);
}
/*
diff --git a/arch/arm/mach-sa1100/cerf.c b/arch/arm/mach-sa1100/cerf.c
index 0aa918e..9484be7 100644
--- a/arch/arm/mach-sa1100/cerf.c
+++ b/arch/arm/mach-sa1100/cerf.c
@@ -29,6 +29,7 @@
#include <asm/mach/serial_sa1100.h>
#include <asm/arch/cerf.h>
+#include <asm/arch/mcp.h>
#include "generic.h"
static struct resource cerfuart2_resources[] = {
@@ -116,10 +117,16 @@
GPDR |= CERF_GPIO_CF_RESET;
}
+static struct mcp_plat_data cerf_mcp_data = {
+ .mccr0 = MCCR0_ADM,
+ .sclk_rate = 11981000,
+};
+
static void __init cerf_init(void)
{
platform_add_devices(cerf_devices, ARRAY_SIZE(cerf_devices));
sa11x0_set_flash_data(&cerf_flash_data, &cerf_flash_resource, 1);
+ sa11x0_set_mcp_data(&cerf_mcp_data);
}
MACHINE_START(CERF, "Intrinsyc CerfBoard/CerfCube")
diff --git a/arch/arm/mach-sa1100/generic.c b/arch/arm/mach-sa1100/generic.c
index 95ae217..3f1e358 100644
--- a/arch/arm/mach-sa1100/generic.c
+++ b/arch/arm/mach-sa1100/generic.c
@@ -221,6 +221,11 @@
.resource = sa11x0mcp_resources,
};
+void sa11x0_set_mcp_data(struct mcp_plat_data *data)
+{
+ sa11x0mcp_device.dev.platform_data = data;
+}
+
static struct resource sa11x0ssp_resources[] = {
[0] = {
.start = 0x80070000,
diff --git a/arch/arm/mach-sa1100/generic.h b/arch/arm/mach-sa1100/generic.h
index bfe41da..279e3af 100644
--- a/arch/arm/mach-sa1100/generic.h
+++ b/arch/arm/mach-sa1100/generic.h
@@ -34,5 +34,8 @@
extern void sa11x0_set_flash_data(struct flash_platform_data *flash,
struct resource *res, int nr);
+struct sa11x0_ssp_plat_ops;
+extern void sa11x0_set_ssp_data(struct sa11x0_ssp_plat_ops *ops);
+
struct irda_platform_data;
void sa11x0_set_irda_data(struct irda_platform_data *irda);
diff --git a/arch/arm/mach-sa1100/lart.c b/arch/arm/mach-sa1100/lart.c
index 870b488..ed6744d 100644
--- a/arch/arm/mach-sa1100/lart.c
+++ b/arch/arm/mach-sa1100/lart.c
@@ -13,12 +13,23 @@
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/serial_sa1100.h>
+#include <asm/arch/mcp.h>
#include "generic.h"
#warning "include/asm/arch-sa1100/ide.h needs fixing for lart"
+static struct mcp_plat_data lart_mcp_data = {
+ .mccr0 = MCCR0_ADM,
+ .sclk_rate = 11981000,
+};
+
+static void __init lart_init(void)
+{
+ sa11x0_set_mcp_data(&lart_mcp_data);
+}
+
static struct map_desc lart_io_desc[] __initdata = {
/* virtual physical length type */
{ 0xe8000000, 0x00000000, 0x00400000, MT_DEVICE }, /* main flash memory */
@@ -47,5 +58,6 @@
.boot_params = 0xc0000100,
.map_io = lart_map_io,
.init_irq = sa1100_init_irq,
+ .init_machine = lart_init,
.timer = &sa1100_timer,
MACHINE_END
diff --git a/arch/arm/mach-sa1100/shannon.c b/arch/arm/mach-sa1100/shannon.c
index 43a0035..7482288 100644
--- a/arch/arm/mach-sa1100/shannon.c
+++ b/arch/arm/mach-sa1100/shannon.c
@@ -18,6 +18,7 @@
#include <asm/mach/flash.h>
#include <asm/mach/map.h>
#include <asm/mach/serial_sa1100.h>
+#include <asm/arch/mcp.h>
#include <asm/arch/shannon.h>
#include "generic.h"
@@ -52,9 +53,15 @@
.flags = IORESOURCE_MEM,
};
+static struct mcp_plat_data shannon_mcp_data = {
+ .mccr0 = MCCR0_ADM,
+ .sclk_rate = 11981000,
+};
+
static void __init shannon_init(void)
{
sa11x0_set_flash_data(&shannon_flash_data, &shannon_flash_resource, 1);
+ sa11x0_set_mcp_data(&shannon_mcp_data);
}
static void __init shannon_map_io(void)
diff --git a/arch/arm/mach-sa1100/simpad.c b/arch/arm/mach-sa1100/simpad.c
index 7797858..07f6d5f 100644
--- a/arch/arm/mach-sa1100/simpad.c
+++ b/arch/arm/mach-sa1100/simpad.c
@@ -23,6 +23,7 @@
#include <asm/mach/flash.h>
#include <asm/mach/map.h>
#include <asm/mach/serial_sa1100.h>
+#include <asm/arch/mcp.h>
#include <asm/arch/simpad.h>
#include <linux/serial_core.h>
@@ -123,6 +124,11 @@
}
};
+static struct mcp_plat_data simpad_mcp_data = {
+ .mccr0 = MCCR0_ADM,
+ .sclk_rate = 11981000,
+};
+
static void __init simpad_map_io(void)
@@ -157,6 +163,7 @@
sa11x0_set_flash_data(&simpad_flash_data, simpad_flash_resources,
ARRAY_SIZE(simpad_flash_resources));
+ sa11x0_set_mcp_data(&simpad_mcp_data);
}
static void simpad_power_off(void)
diff --git a/arch/arm26/kernel/signal.c b/arch/arm26/kernel/signal.c
index 356d980..ce2055b 100644
--- a/arch/arm26/kernel/signal.c
+++ b/arch/arm26/kernel/signal.c
@@ -454,14 +454,13 @@
if (ka->sa.sa_flags & SA_ONESHOT)
ka->sa.sa_handler = SIG_DFL;
- if (!(ka->sa.sa_flags & SA_NODEFER)) {
- spin_lock_irq(&tsk->sighand->siglock);
- sigorsets(&tsk->blocked, &tsk->blocked,
- &ka->sa.sa_mask);
+ spin_lock_irq(&tsk->sighand->siglock);
+ sigorsets(&tsk->blocked, &tsk->blocked,
+ &ka->sa.sa_mask);
+ if (!(ka->sa.sa_flags & SA_NODEFER))
sigaddset(&tsk->blocked, sig);
- recalc_sigpending();
- spin_unlock_irq(&tsk->sighand->siglock);
- }
+ recalc_sigpending();
+ spin_unlock_irq(&tsk->sighand->siglock);
return;
}
diff --git a/arch/cris/arch-v10/kernel/signal.c b/arch/cris/arch-v10/kernel/signal.c
index 85e0032..6937719 100644
--- a/arch/cris/arch-v10/kernel/signal.c
+++ b/arch/cris/arch-v10/kernel/signal.c
@@ -517,13 +517,12 @@
if (ka->sa.sa_flags & SA_ONESHOT)
ka->sa.sa_handler = SIG_DFL;
- if (!(ka->sa.sa_flags & SA_NODEFER)) {
- spin_lock_irq(¤t->sighand->siglock);
- sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ spin_lock_irq(¤t->sighand->siglock);
+ sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ if (!(ka->sa.sa_flags & SA_NODEFER))
sigaddset(¤t->blocked,sig);
- recalc_sigpending();
- spin_unlock_irq(¤t->sighand->siglock);
- }
+ recalc_sigpending();
+ spin_unlock_irq(¤t->sighand->siglock);
}
/*
diff --git a/arch/cris/arch-v32/kernel/signal.c b/arch/cris/arch-v32/kernel/signal.c
index fb4c79d..0a3614d 100644
--- a/arch/cris/arch-v32/kernel/signal.c
+++ b/arch/cris/arch-v32/kernel/signal.c
@@ -568,13 +568,12 @@
if (ka->sa.sa_flags & SA_ONESHOT)
ka->sa.sa_handler = SIG_DFL;
- if (!(ka->sa.sa_flags & SA_NODEFER)) {
- spin_lock_irq(¤t->sighand->siglock);
- sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ spin_lock_irq(¤t->sighand->siglock);
+ sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ if (!(ka->sa.sa_flags & SA_NODEFER))
sigaddset(¤t->blocked,sig);
- recalc_sigpending();
- spin_unlock_irq(¤t->sighand->siglock);
- }
+ recalc_sigpending();
+ spin_unlock_irq(¤t->sighand->siglock);
}
/*
diff --git a/arch/frv/kernel/signal.c b/arch/frv/kernel/signal.c
index 36a2dff..d4ccc07 100644
--- a/arch/frv/kernel/signal.c
+++ b/arch/frv/kernel/signal.c
@@ -506,13 +506,12 @@
else
setup_frame(sig, ka, oldset, regs);
- if (!(ka->sa.sa_flags & SA_NODEFER)) {
- spin_lock_irq(¤t->sighand->siglock);
- sigorsets(¤t->blocked, ¤t->blocked, &ka->sa.sa_mask);
+ spin_lock_irq(¤t->sighand->siglock);
+ sigorsets(¤t->blocked, ¤t->blocked, &ka->sa.sa_mask);
+ if (!(ka->sa.sa_flags & SA_NODEFER))
sigaddset(¤t->blocked, sig);
- recalc_sigpending();
- spin_unlock_irq(¤t->sighand->siglock);
- }
+ recalc_sigpending();
+ spin_unlock_irq(¤t->sighand->siglock);
} /* end handle_signal() */
/*****************************************************************************/
diff --git a/arch/h8300/kernel/signal.c b/arch/h8300/kernel/signal.c
index 5aab87e..f13d5e8 100644
--- a/arch/h8300/kernel/signal.c
+++ b/arch/h8300/kernel/signal.c
@@ -488,13 +488,12 @@
else
setup_frame(sig, ka, oldset, regs);
- if (!(ka->sa.sa_flags & SA_NODEFER)) {
- spin_lock_irq(¤t->sighand->siglock);
- sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ spin_lock_irq(¤t->sighand->siglock);
+ sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ if (!(ka->sa.sa_flags & SA_NODEFER))
sigaddset(¤t->blocked,sig);
- recalc_sigpending();
- spin_unlock_irq(¤t->sighand->siglock);
- }
+ recalc_sigpending();
+ spin_unlock_irq(¤t->sighand->siglock);
}
/*
diff --git a/arch/i386/kernel/signal.c b/arch/i386/kernel/signal.c
index 89ef7ad..140e340 100644
--- a/arch/i386/kernel/signal.c
+++ b/arch/i386/kernel/signal.c
@@ -577,10 +577,11 @@
else
ret = setup_frame(sig, ka, oldset, regs);
- if (ret && !(ka->sa.sa_flags & SA_NODEFER)) {
+ if (ret) {
spin_lock_irq(¤t->sighand->siglock);
sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
- sigaddset(¤t->blocked,sig);
+ if (!(ka->sa.sa_flags & SA_NODEFER))
+ sigaddset(¤t->blocked,sig);
recalc_sigpending();
spin_unlock_irq(¤t->sighand->siglock);
}
diff --git a/arch/ia64/kernel/signal.c b/arch/ia64/kernel/signal.c
index b8a0a7d..774f34b 100644
--- a/arch/ia64/kernel/signal.c
+++ b/arch/ia64/kernel/signal.c
@@ -467,15 +467,12 @@
if (!setup_frame(sig, ka, info, oldset, scr))
return 0;
- if (!(ka->sa.sa_flags & SA_NODEFER)) {
- spin_lock_irq(¤t->sighand->siglock);
- {
- sigorsets(¤t->blocked, ¤t->blocked, &ka->sa.sa_mask);
- sigaddset(¤t->blocked, sig);
- recalc_sigpending();
- }
- spin_unlock_irq(¤t->sighand->siglock);
- }
+ spin_lock_irq(¤t->sighand->siglock);
+ sigorsets(¤t->blocked, ¤t->blocked, &ka->sa.sa_mask);
+ if (!(ka->sa.sa_flags & SA_NODEFER))
+ sigaddset(¤t->blocked, sig);
+ recalc_sigpending();
+ spin_unlock_irq(¤t->sighand->siglock);
return 1;
}
diff --git a/arch/m32r/kernel/signal.c b/arch/m32r/kernel/signal.c
index 5aef7e4..71763f7 100644
--- a/arch/m32r/kernel/signal.c
+++ b/arch/m32r/kernel/signal.c
@@ -341,13 +341,12 @@
/* Set up the stack frame */
setup_rt_frame(sig, ka, info, oldset, regs);
- if (!(ka->sa.sa_flags & SA_NODEFER)) {
- spin_lock_irq(¤t->sighand->siglock);
- sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ spin_lock_irq(¤t->sighand->siglock);
+ sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ if (!(ka->sa.sa_flags & SA_NODEFER))
sigaddset(¤t->blocked,sig);
- recalc_sigpending();
- spin_unlock_irq(¤t->sighand->siglock);
- }
+ recalc_sigpending();
+ spin_unlock_irq(¤t->sighand->siglock);
}
/*
diff --git a/arch/m68knommu/kernel/signal.c b/arch/m68knommu/kernel/signal.c
index 30dceb5..43a2726 100644
--- a/arch/m68knommu/kernel/signal.c
+++ b/arch/m68knommu/kernel/signal.c
@@ -732,13 +732,12 @@
if (ka->sa.sa_flags & SA_ONESHOT)
ka->sa.sa_handler = SIG_DFL;
- if (!(ka->sa.sa_flags & SA_NODEFER)) {
- spin_lock_irq(¤t->sighand->siglock);
- sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ spin_lock_irq(¤t->sighand->siglock);
+ sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ if (!(ka->sa.sa_flags & SA_NODEFER))
sigaddset(¤t->blocked,sig);
- recalc_sigpending();
- spin_unlock_irq(¤t->sighand->siglock);
- }
+ recalc_sigpending();
+ spin_unlock_irq(¤t->sighand->siglock);
}
/*
diff --git a/arch/mips/kernel/irixsig.c b/arch/mips/kernel/irixsig.c
index 4024478..4c114ae 100644
--- a/arch/mips/kernel/irixsig.c
+++ b/arch/mips/kernel/irixsig.c
@@ -155,13 +155,12 @@
else
setup_irix_frame(ka, regs, sig, oldset);
- if (!(ka->sa.sa_flags & SA_NODEFER)) {
- spin_lock_irq(¤t->sighand->siglock);
- sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ spin_lock_irq(¤t->sighand->siglock);
+ sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ if (!(ka->sa.sa_flags & SA_NODEFER))
sigaddset(¤t->blocked,sig);
- recalc_sigpending();
- spin_unlock_irq(¤t->sighand->siglock);
- }
+ recalc_sigpending();
+ spin_unlock_irq(¤t->sighand->siglock);
}
asmlinkage int do_irix_signal(sigset_t *oldset, struct pt_regs *regs)
diff --git a/arch/mips/kernel/signal.c b/arch/mips/kernel/signal.c
index 65ee153..0209c1d 100644
--- a/arch/mips/kernel/signal.c
+++ b/arch/mips/kernel/signal.c
@@ -425,13 +425,12 @@
setup_frame(ka, regs, sig, oldset);
#endif
- if (!(ka->sa.sa_flags & SA_NODEFER)) {
- spin_lock_irq(¤t->sighand->siglock);
- sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ spin_lock_irq(¤t->sighand->siglock);
+ sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ if (!(ka->sa.sa_flags & SA_NODEFER))
sigaddset(¤t->blocked,sig);
- recalc_sigpending();
- spin_unlock_irq(¤t->sighand->siglock);
- }
+ recalc_sigpending();
+ spin_unlock_irq(¤t->sighand->siglock);
}
extern int do_signal32(sigset_t *oldset, struct pt_regs *regs);
diff --git a/arch/mips/kernel/signal32.c b/arch/mips/kernel/signal32.c
index c1a69cf..f6875f0 100644
--- a/arch/mips/kernel/signal32.c
+++ b/arch/mips/kernel/signal32.c
@@ -751,13 +751,12 @@
else
setup_frame(ka, regs, sig, oldset);
- if (!(ka->sa.sa_flags & SA_NODEFER)) {
- spin_lock_irq(¤t->sighand->siglock);
- sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ spin_lock_irq(¤t->sighand->siglock);
+ sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ if (!(ka->sa.sa_flags & SA_NODEFER))
sigaddset(¤t->blocked,sig);
- recalc_sigpending();
- spin_unlock_irq(¤t->sighand->siglock);
- }
+ recalc_sigpending();
+ spin_unlock_irq(¤t->sighand->siglock);
}
int do_signal32(sigset_t *oldset, struct pt_regs *regs)
diff --git a/arch/parisc/kernel/signal.c b/arch/parisc/kernel/signal.c
index 9421bb9..55d71c1 100644
--- a/arch/parisc/kernel/signal.c
+++ b/arch/parisc/kernel/signal.c
@@ -517,13 +517,12 @@
if (!setup_rt_frame(sig, ka, info, oldset, regs, in_syscall))
return 0;
- if (!(ka->sa.sa_flags & SA_NODEFER)) {
- spin_lock_irq(¤t->sighand->siglock);
- sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ spin_lock_irq(¤t->sighand->siglock);
+ sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ if (!(ka->sa.sa_flags & SA_NODEFER))
sigaddset(¤t->blocked,sig);
- recalc_sigpending();
- spin_unlock_irq(¤t->sighand->siglock);
- }
+ recalc_sigpending();
+ spin_unlock_irq(¤t->sighand->siglock);
return 1;
}
diff --git a/arch/ppc/kernel/signal.c b/arch/ppc/kernel/signal.c
index 8aaeb6f..2244bf9 100644
--- a/arch/ppc/kernel/signal.c
+++ b/arch/ppc/kernel/signal.c
@@ -759,13 +759,12 @@
else
handle_signal(signr, &ka, &info, oldset, regs, newsp);
- if (!(ka.sa.sa_flags & SA_NODEFER)) {
- spin_lock_irq(¤t->sighand->siglock);
- sigorsets(¤t->blocked,¤t->blocked,&ka.sa.sa_mask);
+ spin_lock_irq(¤t->sighand->siglock);
+ sigorsets(¤t->blocked,¤t->blocked,&ka.sa.sa_mask);
+ if (!(ka.sa.sa_flags & SA_NODEFER))
sigaddset(¤t->blocked, signr);
- recalc_sigpending();
- spin_unlock_irq(¤t->sighand->siglock);
- }
+ recalc_sigpending();
+ spin_unlock_irq(¤t->sighand->siglock);
return 1;
}
diff --git a/arch/ppc64/kernel/signal.c b/arch/ppc64/kernel/signal.c
index bf78227..49a79a5 100644
--- a/arch/ppc64/kernel/signal.c
+++ b/arch/ppc64/kernel/signal.c
@@ -481,10 +481,11 @@
/* Set up Signal Frame */
ret = setup_rt_frame(sig, ka, info, oldset, regs);
- if (ret && !(ka->sa.sa_flags & SA_NODEFER)) {
+ if (ret) {
spin_lock_irq(¤t->sighand->siglock);
sigorsets(¤t->blocked, ¤t->blocked, &ka->sa.sa_mask);
- sigaddset(¤t->blocked,sig);
+ if (!(ka->sa.sa_flags & SA_NODEFER))
+ sigaddset(¤t->blocked,sig);
recalc_sigpending();
spin_unlock_irq(¤t->sighand->siglock);
}
diff --git a/arch/ppc64/kernel/signal32.c b/arch/ppc64/kernel/signal32.c
index 3c2fa5c..46f4d6c 100644
--- a/arch/ppc64/kernel/signal32.c
+++ b/arch/ppc64/kernel/signal32.c
@@ -976,11 +976,12 @@
else
ret = handle_signal32(signr, &ka, &info, oldset, regs, newsp);
- if (ret && !(ka.sa.sa_flags & SA_NODEFER)) {
+ if (ret) {
spin_lock_irq(¤t->sighand->siglock);
sigorsets(¤t->blocked, ¤t->blocked,
&ka.sa.sa_mask);
- sigaddset(¤t->blocked, signr);
+ if (!(ka.sa.sa_flags & SA_NODEFER))
+ sigaddset(¤t->blocked, signr);
recalc_sigpending();
spin_unlock_irq(¤t->sighand->siglock);
}
diff --git a/arch/s390/kernel/compat_signal.c b/arch/s390/kernel/compat_signal.c
index d05d65a..7358cdb 100644
--- a/arch/s390/kernel/compat_signal.c
+++ b/arch/s390/kernel/compat_signal.c
@@ -637,12 +637,11 @@
else
setup_frame32(sig, ka, oldset, regs);
- if (!(ka->sa.sa_flags & SA_NODEFER)) {
- spin_lock_irq(¤t->sighand->siglock);
- sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ spin_lock_irq(¤t->sighand->siglock);
+ sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ if (!(ka->sa.sa_flags & SA_NODEFER))
sigaddset(¤t->blocked,sig);
- recalc_sigpending();
- spin_unlock_irq(¤t->sighand->siglock);
- }
+ recalc_sigpending();
+ spin_unlock_irq(¤t->sighand->siglock);
}
diff --git a/arch/s390/kernel/signal.c b/arch/s390/kernel/signal.c
index 610c1d0..6a3f5b7 100644
--- a/arch/s390/kernel/signal.c
+++ b/arch/s390/kernel/signal.c
@@ -429,13 +429,12 @@
else
setup_frame(sig, ka, oldset, regs);
- if (!(ka->sa.sa_flags & SA_NODEFER)) {
- spin_lock_irq(¤t->sighand->siglock);
- sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ spin_lock_irq(¤t->sighand->siglock);
+ sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ if (!(ka->sa.sa_flags & SA_NODEFER))
sigaddset(¤t->blocked,sig);
- recalc_sigpending();
- spin_unlock_irq(¤t->sighand->siglock);
- }
+ recalc_sigpending();
+ spin_unlock_irq(¤t->sighand->siglock);
}
/*
diff --git a/arch/sh/kernel/signal.c b/arch/sh/kernel/signal.c
index 8022243..b475c4d 100644
--- a/arch/sh/kernel/signal.c
+++ b/arch/sh/kernel/signal.c
@@ -546,13 +546,12 @@
if (ka->sa.sa_flags & SA_ONESHOT)
ka->sa.sa_handler = SIG_DFL;
- if (!(ka->sa.sa_flags & SA_NODEFER)) {
- spin_lock_irq(¤t->sighand->siglock);
- sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ spin_lock_irq(¤t->sighand->siglock);
+ sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ if (!(ka->sa.sa_flags & SA_NODEFER))
sigaddset(¤t->blocked,sig);
- recalc_sigpending();
- spin_unlock_irq(¤t->sighand->siglock);
- }
+ recalc_sigpending();
+ spin_unlock_irq(¤t->sighand->siglock);
}
/*
diff --git a/arch/sh64/kernel/signal.c b/arch/sh64/kernel/signal.c
index c6a14a8..3ea8929e 100644
--- a/arch/sh64/kernel/signal.c
+++ b/arch/sh64/kernel/signal.c
@@ -664,13 +664,12 @@
else
setup_frame(sig, ka, oldset, regs);
- if (!(ka->sa.sa_flags & SA_NODEFER)) {
- spin_lock_irq(¤t->sighand->siglock);
- sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ spin_lock_irq(¤t->sighand->siglock);
+ sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ if (!(ka->sa.sa_flags & SA_NODEFER))
sigaddset(¤t->blocked,sig);
- recalc_sigpending();
- spin_unlock_irq(¤t->sighand->siglock);
- }
+ recalc_sigpending();
+ spin_unlock_irq(¤t->sighand->siglock);
}
/*
diff --git a/arch/sparc/kernel/signal.c b/arch/sparc/kernel/signal.c
index 011ff35..5f34d7d 100644
--- a/arch/sparc/kernel/signal.c
+++ b/arch/sparc/kernel/signal.c
@@ -1034,13 +1034,12 @@
else
setup_frame(&ka->sa, regs, signr, oldset, info);
}
- if (!(ka->sa.sa_flags & SA_NOMASK)) {
- spin_lock_irq(¤t->sighand->siglock);
- sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ spin_lock_irq(¤t->sighand->siglock);
+ sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ if (!(ka->sa.sa_flags & SA_NOMASK))
sigaddset(¤t->blocked, signr);
- recalc_sigpending();
- spin_unlock_irq(¤t->sighand->siglock);
- }
+ recalc_sigpending();
+ spin_unlock_irq(¤t->sighand->siglock);
}
static inline void syscall_restart(unsigned long orig_i0, struct pt_regs *regs,
diff --git a/arch/sparc64/kernel/signal.c b/arch/sparc64/kernel/signal.c
index b279346..60f5dfa 100644
--- a/arch/sparc64/kernel/signal.c
+++ b/arch/sparc64/kernel/signal.c
@@ -574,13 +574,12 @@
{
setup_rt_frame(ka, regs, signr, oldset,
(ka->sa.sa_flags & SA_SIGINFO) ? info : NULL);
- if (!(ka->sa.sa_flags & SA_NOMASK)) {
- spin_lock_irq(¤t->sighand->siglock);
- sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ spin_lock_irq(¤t->sighand->siglock);
+ sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ if (!(ka->sa.sa_flags & SA_NOMASK))
sigaddset(¤t->blocked,signr);
- recalc_sigpending();
- spin_unlock_irq(¤t->sighand->siglock);
- }
+ recalc_sigpending();
+ spin_unlock_irq(¤t->sighand->siglock);
}
static inline void syscall_restart(unsigned long orig_i0, struct pt_regs *regs,
diff --git a/arch/sparc64/kernel/signal32.c b/arch/sparc64/kernel/signal32.c
index f28428f4..b1ed230 100644
--- a/arch/sparc64/kernel/signal32.c
+++ b/arch/sparc64/kernel/signal32.c
@@ -1325,13 +1325,12 @@
else
setup_frame32(&ka->sa, regs, signr, oldset, info);
}
- if (!(ka->sa.sa_flags & SA_NOMASK)) {
- spin_lock_irq(¤t->sighand->siglock);
- sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ spin_lock_irq(¤t->sighand->siglock);
+ sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ if (!(ka->sa.sa_flags & SA_NOMASK))
sigaddset(¤t->blocked,signr);
- recalc_sigpending();
- spin_unlock_irq(¤t->sighand->siglock);
- }
+ recalc_sigpending();
+ spin_unlock_irq(¤t->sighand->siglock);
}
static inline void syscall_restart32(unsigned long orig_i0, struct pt_regs *regs,
diff --git a/arch/um/drivers/mmapper_kern.c b/arch/um/drivers/mmapper_kern.c
index a37a5ac..022f67b 100644
--- a/arch/um/drivers/mmapper_kern.c
+++ b/arch/um/drivers/mmapper_kern.c
@@ -9,19 +9,11 @@
*
*/
-#include <linux/types.h>
-#include <linux/kdev_t.h>
-#include <linux/time.h>
-#include <linux/devfs_fs_kernel.h>
+#include <linux/init.h>
#include <linux/module.h>
#include <linux/mm.h>
-#include <linux/slab.h>
-#include <linux/init.h>
-#include <linux/smp_lock.h>
#include <linux/miscdevice.h>
#include <asm/uaccess.h>
-#include <asm/irq.h>
-#include <asm/pgtable.h>
#include "mem_user.h"
#include "user_util.h"
@@ -31,35 +23,22 @@
static char *v_buf = NULL;
static ssize_t
-mmapper_read(struct file *file, char *buf, size_t count, loff_t *ppos)
+mmapper_read(struct file *file, char __user *buf, size_t count, loff_t *ppos)
{
- if(*ppos > mmapper_size)
- return -EINVAL;
-
- if(count + *ppos > mmapper_size)
- count = count + *ppos - mmapper_size;
-
- if(count < 0)
- return -EINVAL;
-
- copy_to_user(buf,&v_buf[*ppos],count);
-
- return count;
+ return simple_read_from_buffer(buf, count, ppos, v_buf, mmapper_size);
}
static ssize_t
-mmapper_write(struct file *file, const char *buf, size_t count, loff_t *ppos)
+mmapper_write(struct file *file, const char __user *buf, size_t count, loff_t *ppos)
{
- if(*ppos > mmapper_size)
+ if (*ppos > mmapper_size)
return -EINVAL;
- if(count + *ppos > mmapper_size)
- count = count + *ppos - mmapper_size;
+ if (count > mmapper_size - *ppos)
+ count = mmapper_size - *ppos;
- if(count < 0)
- return -EINVAL;
-
- copy_from_user(&v_buf[*ppos],buf,count);
+ if (copy_from_user(&v_buf[*ppos], buf, count))
+ return -EFAULT;
return count;
}
@@ -77,7 +56,6 @@
int ret = -EINVAL;
int size;
- lock_kernel();
if (vma->vm_pgoff != 0)
goto out;
@@ -92,7 +70,6 @@
goto out;
ret = 0;
out:
- unlock_kernel();
return ret;
}
diff --git a/arch/um/kernel/signal_kern.c b/arch/um/kernel/signal_kern.c
index 7807a3e..03618bd 100644
--- a/arch/um/kernel/signal_kern.c
+++ b/arch/um/kernel/signal_kern.c
@@ -87,12 +87,12 @@
recalc_sigpending();
spin_unlock_irq(¤t->sighand->siglock);
force_sigsegv(signr, current);
- }
- else if(!(ka->sa.sa_flags & SA_NODEFER)){
+ } else {
spin_lock_irq(¤t->sighand->siglock);
sigorsets(¤t->blocked, ¤t->blocked,
&ka->sa.sa_mask);
- sigaddset(¤t->blocked, signr);
+ if(!(ka->sa.sa_flags & SA_NODEFER))
+ sigaddset(¤t->blocked, signr);
recalc_sigpending();
spin_unlock_irq(¤t->sighand->siglock);
}
diff --git a/arch/v850/kernel/signal.c b/arch/v850/kernel/signal.c
index 37061e3..633e4e1 100644
--- a/arch/v850/kernel/signal.c
+++ b/arch/v850/kernel/signal.c
@@ -462,13 +462,12 @@
else
setup_frame(sig, ka, oldset, regs);
- if (!(ka->sa.sa_flags & SA_NODEFER)) {
- spin_lock_irq(¤t->sighand->siglock);
- sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ spin_lock_irq(¤t->sighand->siglock);
+ sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
+ if (!(ka->sa.sa_flags & SA_NODEFER))
sigaddset(¤t->blocked,sig);
- recalc_sigpending();
- spin_unlock_irq(¤t->sighand->siglock);
- }
+ recalc_sigpending();
+ spin_unlock_irq(¤t->sighand->siglock);
}
/*
diff --git a/arch/x86_64/kernel/e820.c b/arch/x86_64/kernel/e820.c
index 6ded3a5..b548dea 100644
--- a/arch/x86_64/kernel/e820.c
+++ b/arch/x86_64/kernel/e820.c
@@ -185,6 +185,40 @@
}
/*
+ * Compute how much memory is missing in a range.
+ * Unlike the other functions in this file the arguments are in page numbers.
+ */
+unsigned long __init
+e820_hole_size(unsigned long start_pfn, unsigned long end_pfn)
+{
+ unsigned long ram = 0;
+ unsigned long start = start_pfn << PAGE_SHIFT;
+ unsigned long end = end_pfn << PAGE_SHIFT;
+ int i;
+ for (i = 0; i < e820.nr_map; i++) {
+ struct e820entry *ei = &e820.map[i];
+ unsigned long last, addr;
+
+ if (ei->type != E820_RAM ||
+ ei->addr+ei->size <= start ||
+ ei->addr >= end)
+ continue;
+
+ addr = round_up(ei->addr, PAGE_SIZE);
+ if (addr < start)
+ addr = start;
+
+ last = round_down(ei->addr + ei->size, PAGE_SIZE);
+ if (last >= end)
+ last = end;
+
+ if (last > addr)
+ ram += last - addr;
+ }
+ return ((end - start) - ram) >> PAGE_SHIFT;
+}
+
+/*
* Mark e820 reserved areas as busy for the resource manager.
*/
void __init e820_reserve_resources(void)
diff --git a/arch/x86_64/kernel/signal.c b/arch/x86_64/kernel/signal.c
index 98590a9..d642fbf 100644
--- a/arch/x86_64/kernel/signal.c
+++ b/arch/x86_64/kernel/signal.c
@@ -394,10 +394,11 @@
#endif
ret = setup_rt_frame(sig, ka, info, oldset, regs);
- if (ret && !(ka->sa.sa_flags & SA_NODEFER)) {
+ if (ret) {
spin_lock_irq(¤t->sighand->siglock);
sigorsets(¤t->blocked,¤t->blocked,&ka->sa.sa_mask);
- sigaddset(¤t->blocked,sig);
+ if (!(ka->sa.sa_flags & SA_NODEFER))
+ sigaddset(¤t->blocked,sig);
recalc_sigpending();
spin_unlock_irq(¤t->sighand->siglock);
}
diff --git a/arch/x86_64/mm/init.c b/arch/x86_64/mm/init.c
index 72e4b36..aa4a518 100644
--- a/arch/x86_64/mm/init.c
+++ b/arch/x86_64/mm/init.c
@@ -322,18 +322,26 @@
void __init paging_init(void)
{
{
- unsigned long zones_size[MAX_NR_ZONES] = {0, 0, 0};
+ unsigned long zones_size[MAX_NR_ZONES];
+ unsigned long holes[MAX_NR_ZONES];
unsigned int max_dma;
+ memset(zones_size, 0, sizeof(zones_size));
+ memset(holes, 0, sizeof(holes));
+
max_dma = virt_to_phys((char *)MAX_DMA_ADDRESS) >> PAGE_SHIFT;
- if (end_pfn < max_dma)
+ if (end_pfn < max_dma) {
zones_size[ZONE_DMA] = end_pfn;
- else {
+ holes[ZONE_DMA] = e820_hole_size(0, end_pfn);
+ } else {
zones_size[ZONE_DMA] = max_dma;
+ holes[ZONE_DMA] = e820_hole_size(0, max_dma);
zones_size[ZONE_NORMAL] = end_pfn - max_dma;
+ holes[ZONE_NORMAL] = e820_hole_size(max_dma, end_pfn);
}
- free_area_init(zones_size);
+ free_area_init_node(0, NODE_DATA(0), zones_size,
+ __pa(PAGE_OFFSET) >> PAGE_SHIFT, holes);
}
return;
}
diff --git a/arch/x86_64/mm/numa.c b/arch/x86_64/mm/numa.c
index 70cb290..6a156f5 100644
--- a/arch/x86_64/mm/numa.c
+++ b/arch/x86_64/mm/numa.c
@@ -126,9 +126,11 @@
{
unsigned long start_pfn, end_pfn;
unsigned long zones[MAX_NR_ZONES];
+ unsigned long holes[MAX_NR_ZONES];
unsigned long dma_end_pfn;
memset(zones, 0, sizeof(unsigned long) * MAX_NR_ZONES);
+ memset(holes, 0, sizeof(unsigned long) * MAX_NR_ZONES);
start_pfn = node_start_pfn(nodeid);
end_pfn = node_end_pfn(nodeid);
@@ -139,13 +141,17 @@
dma_end_pfn = __pa(MAX_DMA_ADDRESS) >> PAGE_SHIFT;
if (start_pfn < dma_end_pfn) {
zones[ZONE_DMA] = dma_end_pfn - start_pfn;
+ holes[ZONE_DMA] = e820_hole_size(start_pfn, dma_end_pfn);
zones[ZONE_NORMAL] = end_pfn - dma_end_pfn;
+ holes[ZONE_NORMAL] = e820_hole_size(dma_end_pfn, end_pfn);
+
} else {
zones[ZONE_NORMAL] = end_pfn - start_pfn;
+ holes[ZONE_NORMAL] = e820_hole_size(start_pfn, end_pfn);
}
free_area_init_node(nodeid, NODE_DATA(nodeid), zones,
- start_pfn, NULL);
+ start_pfn, holes);
}
void __init numa_init_array(void)
diff --git a/arch/xtensa/kernel/signal.c b/arch/xtensa/kernel/signal.c
index df6e1e1..dc42ced 100644
--- a/arch/xtensa/kernel/signal.c
+++ b/arch/xtensa/kernel/signal.c
@@ -702,12 +702,11 @@
if (ka.sa.sa_flags & SA_ONESHOT)
ka.sa.sa_handler = SIG_DFL;
- if (!(ka.sa.sa_flags & SA_NODEFER)) {
- spin_lock_irq(¤t->sighand->siglock);
- sigorsets(¤t->blocked, ¤t->blocked, &ka.sa.sa_mask);
+ spin_lock_irq(¤t->sighand->siglock);
+ sigorsets(¤t->blocked, ¤t->blocked, &ka.sa.sa_mask);
+ if (!(ka.sa.sa_flags & SA_NODEFER))
sigaddset(¤t->blocked, signr);
- recalc_sigpending();
- spin_unlock_irq(¤t->sighand->siglock);
- }
+ recalc_sigpending();
+ spin_unlock_irq(¤t->sighand->siglock);
return 1;
}
diff --git a/drivers/Kconfig b/drivers/Kconfig
index cecab0a..46d655f 100644
--- a/drivers/Kconfig
+++ b/drivers/Kconfig
@@ -48,6 +48,8 @@
source "drivers/misc/Kconfig"
+source "drivers/mfd/Kconfig"
+
source "drivers/media/Kconfig"
source "drivers/video/Kconfig"
diff --git a/drivers/Makefile b/drivers/Makefile
index 784b93c..86c8654 100644
--- a/drivers/Makefile
+++ b/drivers/Makefile
@@ -26,7 +26,7 @@
obj-$(CONFIG_SERIO) += input/serio/
obj-y += serial/
obj-$(CONFIG_PARPORT) += parport/
-obj-y += base/ block/ misc/ net/ media/
+obj-y += base/ block/ misc/ mfd/ net/ media/
obj-$(CONFIG_NUBUS) += nubus/
obj-$(CONFIG_ATM) += atm/
obj-$(CONFIG_PPC_PMAC) += macintosh/
diff --git a/drivers/acpi/sleep/poweroff.c b/drivers/acpi/sleep/poweroff.c
index f8538b5..a5f947d 100644
--- a/drivers/acpi/sleep/poweroff.c
+++ b/drivers/acpi/sleep/poweroff.c
@@ -55,7 +55,11 @@
static int acpi_shutdown(struct sys_device *x)
{
- return acpi_sleep_prepare(ACPI_STATE_S5);
+ if (system_state == SYSTEM_POWER_OFF) {
+ /* Prepare if we are going to power off the system */
+ return acpi_sleep_prepare(ACPI_STATE_S5);
+ }
+ return 0;
}
static struct sysdev_class acpi_sysclass = {
diff --git a/drivers/char/vt.c b/drivers/char/vt.c
index 30d9673..665103c 100644
--- a/drivers/char/vt.c
+++ b/drivers/char/vt.c
@@ -2433,7 +2433,7 @@
int ret = 0;
acquire_console_sem();
- if (tty->count == 1) {
+ if (tty->driver_data == NULL) {
ret = vc_allocate(currcons);
if (ret == 0) {
struct vc_data *vc = vc_cons[currcons].d;
diff --git a/drivers/hwmon/adm1026.c b/drivers/hwmon/adm1026.c
index ded6e8a..c8a7f47 100644
--- a/drivers/hwmon/adm1026.c
+++ b/drivers/hwmon/adm1026.c
@@ -325,7 +325,7 @@
int adm1026_detach_client(struct i2c_client *client)
{
i2c_detach_client(client);
- kfree(client);
+ kfree(i2c_get_clientdata(client));
return 0;
}
diff --git a/drivers/hwmon/adm1031.c b/drivers/hwmon/adm1031.c
index 4211c8b..9362509 100644
--- a/drivers/hwmon/adm1031.c
+++ b/drivers/hwmon/adm1031.c
@@ -845,7 +845,7 @@
if ((ret = i2c_detach_client(client)) != 0) {
return ret;
}
- kfree(client);
+ kfree(i2c_get_clientdata(client));
return 0;
}
diff --git a/drivers/infiniband/core/Makefile b/drivers/infiniband/core/Makefile
index 10be367..678a7e0 100644
--- a/drivers/infiniband/core/Makefile
+++ b/drivers/infiniband/core/Makefile
@@ -1,5 +1,3 @@
-EXTRA_CFLAGS += -Idrivers/infiniband/include
-
obj-$(CONFIG_INFINIBAND) += ib_core.o ib_mad.o ib_sa.o \
ib_cm.o ib_umad.o ib_ucm.o
obj-$(CONFIG_INFINIBAND_USER_VERBS) += ib_uverbs.o
diff --git a/drivers/infiniband/core/agent.c b/drivers/infiniband/core/agent.c
index 729f0b0..5ac86f5 100644
--- a/drivers/infiniband/core/agent.c
+++ b/drivers/infiniband/core/agent.c
@@ -1,9 +1,10 @@
/*
- * Copyright (c) 2004 Mellanox Technologies Ltd. All rights reserved.
- * Copyright (c) 2004 Infinicon Corporation. All rights reserved.
- * Copyright (c) 2004 Intel Corporation. All rights reserved.
- * Copyright (c) 2004 Topspin Corporation. All rights reserved.
- * Copyright (c) 2004 Voltaire Corporation. All rights reserved.
+ * Copyright (c) 2004, 2005 Mellanox Technologies Ltd. All rights reserved.
+ * Copyright (c) 2004, 2005 Infinicon Corporation. All rights reserved.
+ * Copyright (c) 2004, 2005 Intel Corporation. All rights reserved.
+ * Copyright (c) 2004, 2005 Topspin Corporation. All rights reserved.
+ * Copyright (c) 2004, 2005 Voltaire Corporation. All rights reserved.
+ * Copyright (c) 2005 Sun Microsystems, Inc. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
@@ -40,7 +41,7 @@
#include <asm/bug.h>
-#include <ib_smi.h>
+#include <rdma/ib_smi.h>
#include "smi.h"
#include "agent_priv.h"
diff --git a/drivers/infiniband/core/agent_priv.h b/drivers/infiniband/core/agent_priv.h
index 17435af..2ec6d7f 100644
--- a/drivers/infiniband/core/agent_priv.h
+++ b/drivers/infiniband/core/agent_priv.h
@@ -1,9 +1,9 @@
/*
- * Copyright (c) 2004 Mellanox Technologies Ltd. All rights reserved.
- * Copyright (c) 2004 Infinicon Corporation. All rights reserved.
- * Copyright (c) 2004 Intel Corporation. All rights reserved.
- * Copyright (c) 2004 Topspin Corporation. All rights reserved.
- * Copyright (c) 2004 Voltaire Corporation. All rights reserved.
+ * Copyright (c) 2004, 2005 Mellanox Technologies Ltd. All rights reserved.
+ * Copyright (c) 2004, 2005 Infinicon Corporation. All rights reserved.
+ * Copyright (c) 2004, 2005 Intel Corporation. All rights reserved.
+ * Copyright (c) 2004, 2005 Topspin Corporation. All rights reserved.
+ * Copyright (c) 2004, 2005 Voltaire Corporation. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
diff --git a/drivers/infiniband/core/cache.c b/drivers/infiniband/core/cache.c
index 3042360..f014e63 100644
--- a/drivers/infiniband/core/cache.c
+++ b/drivers/infiniband/core/cache.c
@@ -1,5 +1,8 @@
/*
* Copyright (c) 2004 Topspin Communications. All rights reserved.
+ * Copyright (c) 2005 Intel Corporation. All rights reserved.
+ * Copyright (c) 2005 Sun Microsystems, Inc. All rights reserved.
+ * Copyright (c) 2005 Voltaire, Inc. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
@@ -32,12 +35,11 @@
* $Id: cache.c 1349 2004-12-16 21:09:43Z roland $
*/
-#include <linux/version.h>
#include <linux/module.h>
#include <linux/errno.h>
#include <linux/slab.h>
-#include <ib_cache.h>
+#include <rdma/ib_cache.h>
#include "core_priv.h"
diff --git a/drivers/infiniband/core/cm.c b/drivers/infiniband/core/cm.c
index 403ed12..4de93ba 100644
--- a/drivers/infiniband/core/cm.c
+++ b/drivers/infiniband/core/cm.c
@@ -43,8 +43,8 @@
#include <linux/spinlock.h>
#include <linux/workqueue.h>
-#include <ib_cache.h>
-#include <ib_cm.h>
+#include <rdma/ib_cache.h>
+#include <rdma/ib_cm.h>
#include "cm_msgs.h"
MODULE_AUTHOR("Sean Hefty");
@@ -83,7 +83,7 @@
struct cm_device {
struct list_head list;
struct ib_device *device;
- u64 ca_guid;
+ __be64 ca_guid;
struct cm_port port[0];
};
@@ -100,8 +100,8 @@
struct list_head list;
struct cm_port *port;
struct ib_mad_recv_wc *mad_recv_wc; /* Received MADs */
- u32 local_id; /* Established / timewait */
- u32 remote_id;
+ __be32 local_id; /* Established / timewait */
+ __be32 remote_id;
struct ib_cm_event cm_event;
struct ib_sa_path_rec path[0];
};
@@ -110,8 +110,8 @@
struct cm_work work; /* Must be first. */
struct rb_node remote_qp_node;
struct rb_node remote_id_node;
- u64 remote_ca_guid;
- u32 remote_qpn;
+ __be64 remote_ca_guid;
+ __be32 remote_qpn;
u8 inserted_remote_qp;
u8 inserted_remote_id;
};
@@ -132,11 +132,11 @@
struct cm_av alt_av;
void *private_data;
- u64 tid;
- u32 local_qpn;
- u32 remote_qpn;
- u32 sq_psn;
- u32 rq_psn;
+ __be64 tid;
+ __be32 local_qpn;
+ __be32 remote_qpn;
+ __be32 sq_psn;
+ __be32 rq_psn;
int timeout_ms;
enum ib_mtu path_mtu;
u8 private_data_len;
@@ -253,7 +253,7 @@
u16 dlid, u8 sl, u16 src_path_bits)
{
memset(ah_attr, 0, sizeof ah_attr);
- ah_attr->dlid = be16_to_cpu(dlid);
+ ah_attr->dlid = dlid;
ah_attr->sl = sl;
ah_attr->src_path_bits = src_path_bits;
ah_attr->port_num = port_num;
@@ -264,7 +264,7 @@
{
av->port = port;
av->pkey_index = wc->pkey_index;
- cm_set_ah_attr(&av->ah_attr, port->port_num, cpu_to_be16(wc->slid),
+ cm_set_ah_attr(&av->ah_attr, port->port_num, wc->slid,
wc->sl, wc->dlid_path_bits);
}
@@ -295,8 +295,9 @@
return ret;
av->port = port;
- cm_set_ah_attr(&av->ah_attr, av->port->port_num, path->dlid,
- path->sl, path->slid & 0x7F);
+ cm_set_ah_attr(&av->ah_attr, av->port->port_num,
+ be16_to_cpu(path->dlid), path->sl,
+ be16_to_cpu(path->slid) & 0x7F);
av->packet_life_time = path->packet_life_time;
return 0;
}
@@ -309,26 +310,26 @@
do {
spin_lock_irqsave(&cm.lock, flags);
ret = idr_get_new_above(&cm.local_id_table, cm_id_priv, 1,
- (int *) &cm_id_priv->id.local_id);
+ (__force int *) &cm_id_priv->id.local_id);
spin_unlock_irqrestore(&cm.lock, flags);
} while( (ret == -EAGAIN) && idr_pre_get(&cm.local_id_table, GFP_KERNEL) );
return ret;
}
-static void cm_free_id(u32 local_id)
+static void cm_free_id(__be32 local_id)
{
unsigned long flags;
spin_lock_irqsave(&cm.lock, flags);
- idr_remove(&cm.local_id_table, (int) local_id);
+ idr_remove(&cm.local_id_table, (__force int) local_id);
spin_unlock_irqrestore(&cm.lock, flags);
}
-static struct cm_id_private * cm_get_id(u32 local_id, u32 remote_id)
+static struct cm_id_private * cm_get_id(__be32 local_id, __be32 remote_id)
{
struct cm_id_private *cm_id_priv;
- cm_id_priv = idr_find(&cm.local_id_table, (int) local_id);
+ cm_id_priv = idr_find(&cm.local_id_table, (__force int) local_id);
if (cm_id_priv) {
if (cm_id_priv->id.remote_id == remote_id)
atomic_inc(&cm_id_priv->refcount);
@@ -339,7 +340,7 @@
return cm_id_priv;
}
-static struct cm_id_private * cm_acquire_id(u32 local_id, u32 remote_id)
+static struct cm_id_private * cm_acquire_id(__be32 local_id, __be32 remote_id)
{
struct cm_id_private *cm_id_priv;
unsigned long flags;
@@ -356,8 +357,8 @@
struct rb_node **link = &cm.listen_service_table.rb_node;
struct rb_node *parent = NULL;
struct cm_id_private *cur_cm_id_priv;
- u64 service_id = cm_id_priv->id.service_id;
- u64 service_mask = cm_id_priv->id.service_mask;
+ __be64 service_id = cm_id_priv->id.service_id;
+ __be64 service_mask = cm_id_priv->id.service_mask;
while (*link) {
parent = *link;
@@ -376,7 +377,7 @@
return NULL;
}
-static struct cm_id_private * cm_find_listen(u64 service_id)
+static struct cm_id_private * cm_find_listen(__be64 service_id)
{
struct rb_node *node = cm.listen_service_table.rb_node;
struct cm_id_private *cm_id_priv;
@@ -400,8 +401,8 @@
struct rb_node **link = &cm.remote_id_table.rb_node;
struct rb_node *parent = NULL;
struct cm_timewait_info *cur_timewait_info;
- u64 remote_ca_guid = timewait_info->remote_ca_guid;
- u32 remote_id = timewait_info->work.remote_id;
+ __be64 remote_ca_guid = timewait_info->remote_ca_guid;
+ __be32 remote_id = timewait_info->work.remote_id;
while (*link) {
parent = *link;
@@ -424,8 +425,8 @@
return NULL;
}
-static struct cm_timewait_info * cm_find_remote_id(u64 remote_ca_guid,
- u32 remote_id)
+static struct cm_timewait_info * cm_find_remote_id(__be64 remote_ca_guid,
+ __be32 remote_id)
{
struct rb_node *node = cm.remote_id_table.rb_node;
struct cm_timewait_info *timewait_info;
@@ -453,8 +454,8 @@
struct rb_node **link = &cm.remote_qp_table.rb_node;
struct rb_node *parent = NULL;
struct cm_timewait_info *cur_timewait_info;
- u64 remote_ca_guid = timewait_info->remote_ca_guid;
- u32 remote_qpn = timewait_info->remote_qpn;
+ __be64 remote_ca_guid = timewait_info->remote_ca_guid;
+ __be32 remote_qpn = timewait_info->remote_qpn;
while (*link) {
parent = *link;
@@ -484,7 +485,7 @@
struct rb_node *parent = NULL;
struct cm_id_private *cur_cm_id_priv;
union ib_gid *port_gid = &cm_id_priv->av.dgid;
- u32 remote_id = cm_id_priv->id.remote_id;
+ __be32 remote_id = cm_id_priv->id.remote_id;
while (*link) {
parent = *link;
@@ -598,7 +599,7 @@
spin_unlock_irqrestore(&cm.lock, flags);
}
-static struct cm_timewait_info * cm_create_timewait_info(u32 local_id)
+static struct cm_timewait_info * cm_create_timewait_info(__be32 local_id)
{
struct cm_timewait_info *timewait_info;
@@ -715,14 +716,15 @@
EXPORT_SYMBOL(ib_destroy_cm_id);
int ib_cm_listen(struct ib_cm_id *cm_id,
- u64 service_id,
- u64 service_mask)
+ __be64 service_id,
+ __be64 service_mask)
{
struct cm_id_private *cm_id_priv, *cur_cm_id_priv;
unsigned long flags;
int ret = 0;
- service_mask = service_mask ? service_mask : ~0ULL;
+ service_mask = service_mask ? service_mask :
+ __constant_cpu_to_be64(~0ULL);
service_id &= service_mask;
if ((service_id & IB_SERVICE_ID_AGN_MASK) == IB_CM_ASSIGN_SERVICE_ID &&
(service_id != IB_CM_ASSIGN_SERVICE_ID))
@@ -735,8 +737,8 @@
spin_lock_irqsave(&cm.lock, flags);
if (service_id == IB_CM_ASSIGN_SERVICE_ID) {
- cm_id->service_id = __cpu_to_be64(cm.listen_service_id++);
- cm_id->service_mask = ~0ULL;
+ cm_id->service_id = cpu_to_be64(cm.listen_service_id++);
+ cm_id->service_mask = __constant_cpu_to_be64(~0ULL);
} else {
cm_id->service_id = service_id;
cm_id->service_mask = service_mask;
@@ -752,18 +754,19 @@
}
EXPORT_SYMBOL(ib_cm_listen);
-static u64 cm_form_tid(struct cm_id_private *cm_id_priv,
- enum cm_msg_sequence msg_seq)
+static __be64 cm_form_tid(struct cm_id_private *cm_id_priv,
+ enum cm_msg_sequence msg_seq)
{
u64 hi_tid, low_tid;
hi_tid = ((u64) cm_id_priv->av.port->mad_agent->hi_tid) << 32;
- low_tid = (u64) (cm_id_priv->id.local_id | (msg_seq << 30));
+ low_tid = (u64) ((__force u32)cm_id_priv->id.local_id |
+ (msg_seq << 30));
return cpu_to_be64(hi_tid | low_tid);
}
static void cm_format_mad_hdr(struct ib_mad_hdr *hdr,
- enum cm_msg_attr_id attr_id, u64 tid)
+ __be16 attr_id, __be64 tid)
{
hdr->base_version = IB_MGMT_BASE_VERSION;
hdr->mgmt_class = IB_MGMT_CLASS_CM;
@@ -896,7 +899,7 @@
goto error1;
}
cm_id->service_id = param->service_id;
- cm_id->service_mask = ~0ULL;
+ cm_id->service_mask = __constant_cpu_to_be64(~0ULL);
cm_id_priv->timeout_ms = cm_convert_to_ms(
param->primary_path->packet_life_time) * 2 +
cm_convert_to_ms(
@@ -963,7 +966,7 @@
rej_msg->remote_comm_id = rcv_msg->local_comm_id;
rej_msg->local_comm_id = rcv_msg->remote_comm_id;
cm_rej_set_msg_rejected(rej_msg, msg_rejected);
- rej_msg->reason = reason;
+ rej_msg->reason = cpu_to_be16(reason);
if (ari && ari_length) {
cm_rej_set_reject_info_len(rej_msg, ari_length);
@@ -977,8 +980,8 @@
return ret;
}
-static inline int cm_is_active_peer(u64 local_ca_guid, u64 remote_ca_guid,
- u32 local_qpn, u32 remote_qpn)
+static inline int cm_is_active_peer(__be64 local_ca_guid, __be64 remote_ca_guid,
+ __be32 local_qpn, __be32 remote_qpn)
{
return (be64_to_cpu(local_ca_guid) > be64_to_cpu(remote_ca_guid) ||
((local_ca_guid == remote_ca_guid) &&
@@ -1137,7 +1140,7 @@
break;
}
- rej_msg->reason = reason;
+ rej_msg->reason = cpu_to_be16(reason);
if (ari && ari_length) {
cm_rej_set_reject_info_len(rej_msg, ari_length);
memcpy(rej_msg->ari, ari, ari_length);
@@ -1276,7 +1279,7 @@
cm_id_priv->id.cm_handler = listen_cm_id_priv->id.cm_handler;
cm_id_priv->id.context = listen_cm_id_priv->id.context;
cm_id_priv->id.service_id = req_msg->service_id;
- cm_id_priv->id.service_mask = ~0ULL;
+ cm_id_priv->id.service_mask = __constant_cpu_to_be64(~0ULL);
cm_format_paths_from_req(req_msg, &work->path[0], &work->path[1]);
ret = cm_init_av_by_path(&work->path[0], &cm_id_priv->av);
@@ -1969,7 +1972,7 @@
param = &work->cm_event.param.rej_rcvd;
param->ari = rej_msg->ari;
param->ari_length = cm_rej_get_reject_info_len(rej_msg);
- param->reason = rej_msg->reason;
+ param->reason = __be16_to_cpu(rej_msg->reason);
work->cm_event.private_data = &rej_msg->private_data;
}
@@ -1978,20 +1981,20 @@
struct cm_timewait_info *timewait_info;
struct cm_id_private *cm_id_priv;
unsigned long flags;
- u32 remote_id;
+ __be32 remote_id;
remote_id = rej_msg->local_comm_id;
- if (rej_msg->reason == IB_CM_REJ_TIMEOUT) {
+ if (__be16_to_cpu(rej_msg->reason) == IB_CM_REJ_TIMEOUT) {
spin_lock_irqsave(&cm.lock, flags);
- timewait_info = cm_find_remote_id( *((u64 *) rej_msg->ari),
+ timewait_info = cm_find_remote_id( *((__be64 *) rej_msg->ari),
remote_id);
if (!timewait_info) {
spin_unlock_irqrestore(&cm.lock, flags);
return NULL;
}
cm_id_priv = idr_find(&cm.local_id_table,
- (int) timewait_info->work.local_id);
+ (__force int) timewait_info->work.local_id);
if (cm_id_priv) {
if (cm_id_priv->id.remote_id == remote_id)
atomic_inc(&cm_id_priv->refcount);
@@ -2032,7 +2035,7 @@
/* fall through */
case IB_CM_REQ_RCVD:
case IB_CM_MRA_REQ_SENT:
- if (rej_msg->reason == IB_CM_REJ_STALE_CONN)
+ if (__be16_to_cpu(rej_msg->reason) == IB_CM_REJ_STALE_CONN)
cm_enter_timewait(cm_id_priv);
else
cm_reset_to_idle(cm_id_priv);
@@ -2553,7 +2556,7 @@
cm_format_mad_hdr(&sidr_req_msg->hdr, CM_SIDR_REQ_ATTR_ID,
cm_form_tid(cm_id_priv, CM_MSG_SEQUENCE_SIDR));
sidr_req_msg->request_id = cm_id_priv->id.local_id;
- sidr_req_msg->pkey = param->pkey;
+ sidr_req_msg->pkey = cpu_to_be16(param->pkey);
sidr_req_msg->service_id = param->service_id;
if (param->private_data && param->private_data_len)
@@ -2580,7 +2583,7 @@
goto out;
cm_id->service_id = param->service_id;
- cm_id->service_mask = ~0ULL;
+ cm_id->service_mask = __constant_cpu_to_be64(~0ULL);
cm_id_priv->timeout_ms = param->timeout_ms;
cm_id_priv->max_cm_retries = param->max_cm_retries;
ret = cm_alloc_msg(cm_id_priv, &msg);
@@ -2621,7 +2624,7 @@
sidr_req_msg = (struct cm_sidr_req_msg *)
work->mad_recv_wc->recv_buf.mad;
param = &work->cm_event.param.sidr_req_rcvd;
- param->pkey = sidr_req_msg->pkey;
+ param->pkey = __be16_to_cpu(sidr_req_msg->pkey);
param->listen_id = listen_id;
param->device = work->port->mad_agent->device;
param->port = work->port->port_num;
@@ -2645,7 +2648,7 @@
sidr_req_msg = (struct cm_sidr_req_msg *)
work->mad_recv_wc->recv_buf.mad;
wc = work->mad_recv_wc->wc;
- cm_id_priv->av.dgid.global.subnet_prefix = wc->slid;
+ cm_id_priv->av.dgid.global.subnet_prefix = cpu_to_be64(wc->slid);
cm_id_priv->av.dgid.global.interface_id = 0;
cm_init_av_for_response(work->port, work->mad_recv_wc->wc,
&cm_id_priv->av);
@@ -2673,7 +2676,7 @@
cm_id_priv->id.cm_handler = cur_cm_id_priv->id.cm_handler;
cm_id_priv->id.context = cur_cm_id_priv->id.context;
cm_id_priv->id.service_id = sidr_req_msg->service_id;
- cm_id_priv->id.service_mask = ~0ULL;
+ cm_id_priv->id.service_mask = __constant_cpu_to_be64(~0ULL);
cm_format_sidr_req_event(work, &cur_cm_id_priv->id);
cm_process_work(cm_id_priv, work);
@@ -3175,10 +3178,10 @@
}
EXPORT_SYMBOL(ib_cm_init_qp_attr);
-static u64 cm_get_ca_guid(struct ib_device *device)
+static __be64 cm_get_ca_guid(struct ib_device *device)
{
struct ib_device_attr *device_attr;
- u64 guid;
+ __be64 guid;
int ret;
device_attr = kmalloc(sizeof *device_attr, GFP_KERNEL);
diff --git a/drivers/infiniband/core/cm_msgs.h b/drivers/infiniband/core/cm_msgs.h
index 15a309a..813ab70 100644
--- a/drivers/infiniband/core/cm_msgs.h
+++ b/drivers/infiniband/core/cm_msgs.h
@@ -34,7 +34,7 @@
#if !defined(CM_MSGS_H)
#define CM_MSGS_H
-#include <ib_mad.h>
+#include <rdma/ib_mad.h>
/*
* Parameters to routines below should be in network-byte order, and values
@@ -43,19 +43,17 @@
#define IB_CM_CLASS_VERSION 2 /* IB specification 1.2 */
-enum cm_msg_attr_id {
- CM_REQ_ATTR_ID = __constant_htons(0x0010),
- CM_MRA_ATTR_ID = __constant_htons(0x0011),
- CM_REJ_ATTR_ID = __constant_htons(0x0012),
- CM_REP_ATTR_ID = __constant_htons(0x0013),
- CM_RTU_ATTR_ID = __constant_htons(0x0014),
- CM_DREQ_ATTR_ID = __constant_htons(0x0015),
- CM_DREP_ATTR_ID = __constant_htons(0x0016),
- CM_SIDR_REQ_ATTR_ID = __constant_htons(0x0017),
- CM_SIDR_REP_ATTR_ID = __constant_htons(0x0018),
- CM_LAP_ATTR_ID = __constant_htons(0x0019),
- CM_APR_ATTR_ID = __constant_htons(0x001A)
-};
+#define CM_REQ_ATTR_ID __constant_htons(0x0010)
+#define CM_MRA_ATTR_ID __constant_htons(0x0011)
+#define CM_REJ_ATTR_ID __constant_htons(0x0012)
+#define CM_REP_ATTR_ID __constant_htons(0x0013)
+#define CM_RTU_ATTR_ID __constant_htons(0x0014)
+#define CM_DREQ_ATTR_ID __constant_htons(0x0015)
+#define CM_DREP_ATTR_ID __constant_htons(0x0016)
+#define CM_SIDR_REQ_ATTR_ID __constant_htons(0x0017)
+#define CM_SIDR_REP_ATTR_ID __constant_htons(0x0018)
+#define CM_LAP_ATTR_ID __constant_htons(0x0019)
+#define CM_APR_ATTR_ID __constant_htons(0x001A)
enum cm_msg_sequence {
CM_MSG_SEQUENCE_REQ,
@@ -67,35 +65,35 @@
struct cm_req_msg {
struct ib_mad_hdr hdr;
- u32 local_comm_id;
- u32 rsvd4;
- u64 service_id;
- u64 local_ca_guid;
- u32 rsvd24;
- u32 local_qkey;
+ __be32 local_comm_id;
+ __be32 rsvd4;
+ __be64 service_id;
+ __be64 local_ca_guid;
+ __be32 rsvd24;
+ __be32 local_qkey;
/* local QPN:24, responder resources:8 */
- u32 offset32;
+ __be32 offset32;
/* local EECN:24, initiator depth:8 */
- u32 offset36;
+ __be32 offset36;
/*
* remote EECN:24, remote CM response timeout:5,
* transport service type:2, end-to-end flow control:1
*/
- u32 offset40;
+ __be32 offset40;
/* starting PSN:24, local CM response timeout:5, retry count:3 */
- u32 offset44;
- u16 pkey;
+ __be32 offset44;
+ __be16 pkey;
/* path MTU:4, RDC exists:1, RNR retry count:3. */
u8 offset50;
/* max CM Retries:4, SRQ:1, rsvd:3 */
u8 offset51;
- u16 primary_local_lid;
- u16 primary_remote_lid;
+ __be16 primary_local_lid;
+ __be16 primary_remote_lid;
union ib_gid primary_local_gid;
union ib_gid primary_remote_gid;
/* flow label:20, rsvd:6, packet rate:6 */
- u32 primary_offset88;
+ __be32 primary_offset88;
u8 primary_traffic_class;
u8 primary_hop_limit;
/* SL:4, subnet local:1, rsvd:3 */
@@ -103,12 +101,12 @@
/* local ACK timeout:5, rsvd:3 */
u8 primary_offset95;
- u16 alt_local_lid;
- u16 alt_remote_lid;
+ __be16 alt_local_lid;
+ __be16 alt_remote_lid;
union ib_gid alt_local_gid;
union ib_gid alt_remote_gid;
/* flow label:20, rsvd:6, packet rate:6 */
- u32 alt_offset132;
+ __be32 alt_offset132;
u8 alt_traffic_class;
u8 alt_hop_limit;
/* SL:4, subnet local:1, rsvd:3 */
@@ -120,12 +118,12 @@
} __attribute__ ((packed));
-static inline u32 cm_req_get_local_qpn(struct cm_req_msg *req_msg)
+static inline __be32 cm_req_get_local_qpn(struct cm_req_msg *req_msg)
{
return cpu_to_be32(be32_to_cpu(req_msg->offset32) >> 8);
}
-static inline void cm_req_set_local_qpn(struct cm_req_msg *req_msg, u32 qpn)
+static inline void cm_req_set_local_qpn(struct cm_req_msg *req_msg, __be32 qpn)
{
req_msg->offset32 = cpu_to_be32((be32_to_cpu(qpn) << 8) |
(be32_to_cpu(req_msg->offset32) &
@@ -208,13 +206,13 @@
0xFFFFFFFE));
}
-static inline u32 cm_req_get_starting_psn(struct cm_req_msg *req_msg)
+static inline __be32 cm_req_get_starting_psn(struct cm_req_msg *req_msg)
{
return cpu_to_be32(be32_to_cpu(req_msg->offset44) >> 8);
}
static inline void cm_req_set_starting_psn(struct cm_req_msg *req_msg,
- u32 starting_psn)
+ __be32 starting_psn)
{
req_msg->offset44 = cpu_to_be32((be32_to_cpu(starting_psn) << 8) |
(be32_to_cpu(req_msg->offset44) & 0x000000FF));
@@ -288,13 +286,13 @@
((srq & 0x1) << 3));
}
-static inline u32 cm_req_get_primary_flow_label(struct cm_req_msg *req_msg)
+static inline __be32 cm_req_get_primary_flow_label(struct cm_req_msg *req_msg)
{
- return cpu_to_be32((be32_to_cpu(req_msg->primary_offset88) >> 12));
+ return cpu_to_be32(be32_to_cpu(req_msg->primary_offset88) >> 12);
}
static inline void cm_req_set_primary_flow_label(struct cm_req_msg *req_msg,
- u32 flow_label)
+ __be32 flow_label)
{
req_msg->primary_offset88 = cpu_to_be32(
(be32_to_cpu(req_msg->primary_offset88) &
@@ -350,13 +348,13 @@
(local_ack_timeout << 3));
}
-static inline u32 cm_req_get_alt_flow_label(struct cm_req_msg *req_msg)
+static inline __be32 cm_req_get_alt_flow_label(struct cm_req_msg *req_msg)
{
- return cpu_to_be32((be32_to_cpu(req_msg->alt_offset132) >> 12));
+ return cpu_to_be32(be32_to_cpu(req_msg->alt_offset132) >> 12);
}
static inline void cm_req_set_alt_flow_label(struct cm_req_msg *req_msg,
- u32 flow_label)
+ __be32 flow_label)
{
req_msg->alt_offset132 = cpu_to_be32(
(be32_to_cpu(req_msg->alt_offset132) &
@@ -422,8 +420,8 @@
struct cm_mra_msg {
struct ib_mad_hdr hdr;
- u32 local_comm_id;
- u32 remote_comm_id;
+ __be32 local_comm_id;
+ __be32 remote_comm_id;
/* message MRAed:2, rsvd:6 */
u8 offset8;
/* service timeout:5, rsvd:3 */
@@ -458,13 +456,13 @@
struct cm_rej_msg {
struct ib_mad_hdr hdr;
- u32 local_comm_id;
- u32 remote_comm_id;
+ __be32 local_comm_id;
+ __be32 remote_comm_id;
/* message REJected:2, rsvd:6 */
u8 offset8;
/* reject info length:7, rsvd:1. */
u8 offset9;
- u16 reason;
+ __be16 reason;
u8 ari[IB_CM_REJ_ARI_LENGTH];
u8 private_data[IB_CM_REJ_PRIVATE_DATA_SIZE];
@@ -495,45 +493,45 @@
struct cm_rep_msg {
struct ib_mad_hdr hdr;
- u32 local_comm_id;
- u32 remote_comm_id;
- u32 local_qkey;
+ __be32 local_comm_id;
+ __be32 remote_comm_id;
+ __be32 local_qkey;
/* local QPN:24, rsvd:8 */
- u32 offset12;
+ __be32 offset12;
/* local EECN:24, rsvd:8 */
- u32 offset16;
+ __be32 offset16;
/* starting PSN:24 rsvd:8 */
- u32 offset20;
+ __be32 offset20;
u8 resp_resources;
u8 initiator_depth;
/* target ACK delay:5, failover accepted:2, end-to-end flow control:1 */
u8 offset26;
/* RNR retry count:3, SRQ:1, rsvd:5 */
u8 offset27;
- u64 local_ca_guid;
+ __be64 local_ca_guid;
u8 private_data[IB_CM_REP_PRIVATE_DATA_SIZE];
} __attribute__ ((packed));
-static inline u32 cm_rep_get_local_qpn(struct cm_rep_msg *rep_msg)
+static inline __be32 cm_rep_get_local_qpn(struct cm_rep_msg *rep_msg)
{
return cpu_to_be32(be32_to_cpu(rep_msg->offset12) >> 8);
}
-static inline void cm_rep_set_local_qpn(struct cm_rep_msg *rep_msg, u32 qpn)
+static inline void cm_rep_set_local_qpn(struct cm_rep_msg *rep_msg, __be32 qpn)
{
rep_msg->offset12 = cpu_to_be32((be32_to_cpu(qpn) << 8) |
(be32_to_cpu(rep_msg->offset12) & 0x000000FF));
}
-static inline u32 cm_rep_get_starting_psn(struct cm_rep_msg *rep_msg)
+static inline __be32 cm_rep_get_starting_psn(struct cm_rep_msg *rep_msg)
{
return cpu_to_be32(be32_to_cpu(rep_msg->offset20) >> 8);
}
static inline void cm_rep_set_starting_psn(struct cm_rep_msg *rep_msg,
- u32 starting_psn)
+ __be32 starting_psn)
{
rep_msg->offset20 = cpu_to_be32((be32_to_cpu(starting_psn) << 8) |
(be32_to_cpu(rep_msg->offset20) & 0x000000FF));
@@ -600,8 +598,8 @@
struct cm_rtu_msg {
struct ib_mad_hdr hdr;
- u32 local_comm_id;
- u32 remote_comm_id;
+ __be32 local_comm_id;
+ __be32 remote_comm_id;
u8 private_data[IB_CM_RTU_PRIVATE_DATA_SIZE];
@@ -610,21 +608,21 @@
struct cm_dreq_msg {
struct ib_mad_hdr hdr;
- u32 local_comm_id;
- u32 remote_comm_id;
+ __be32 local_comm_id;
+ __be32 remote_comm_id;
/* remote QPN/EECN:24, rsvd:8 */
- u32 offset8;
+ __be32 offset8;
u8 private_data[IB_CM_DREQ_PRIVATE_DATA_SIZE];
} __attribute__ ((packed));
-static inline u32 cm_dreq_get_remote_qpn(struct cm_dreq_msg *dreq_msg)
+static inline __be32 cm_dreq_get_remote_qpn(struct cm_dreq_msg *dreq_msg)
{
return cpu_to_be32(be32_to_cpu(dreq_msg->offset8) >> 8);
}
-static inline void cm_dreq_set_remote_qpn(struct cm_dreq_msg *dreq_msg, u32 qpn)
+static inline void cm_dreq_set_remote_qpn(struct cm_dreq_msg *dreq_msg, __be32 qpn)
{
dreq_msg->offset8 = cpu_to_be32((be32_to_cpu(qpn) << 8) |
(be32_to_cpu(dreq_msg->offset8) & 0x000000FF));
@@ -633,8 +631,8 @@
struct cm_drep_msg {
struct ib_mad_hdr hdr;
- u32 local_comm_id;
- u32 remote_comm_id;
+ __be32 local_comm_id;
+ __be32 remote_comm_id;
u8 private_data[IB_CM_DREP_PRIVATE_DATA_SIZE];
@@ -643,37 +641,37 @@
struct cm_lap_msg {
struct ib_mad_hdr hdr;
- u32 local_comm_id;
- u32 remote_comm_id;
+ __be32 local_comm_id;
+ __be32 remote_comm_id;
- u32 rsvd8;
+ __be32 rsvd8;
/* remote QPN/EECN:24, remote CM response timeout:5, rsvd:3 */
- u32 offset12;
- u32 rsvd16;
+ __be32 offset12;
+ __be32 rsvd16;
- u16 alt_local_lid;
- u16 alt_remote_lid;
+ __be16 alt_local_lid;
+ __be16 alt_remote_lid;
union ib_gid alt_local_gid;
union ib_gid alt_remote_gid;
/* flow label:20, rsvd:4, traffic class:8 */
- u32 offset56;
+ __be32 offset56;
u8 alt_hop_limit;
/* rsvd:2, packet rate:6 */
- uint8_t offset61;
+ u8 offset61;
/* SL:4, subnet local:1, rsvd:3 */
- uint8_t offset62;
+ u8 offset62;
/* local ACK timeout:5, rsvd:3 */
- uint8_t offset63;
+ u8 offset63;
u8 private_data[IB_CM_LAP_PRIVATE_DATA_SIZE];
} __attribute__ ((packed));
-static inline u32 cm_lap_get_remote_qpn(struct cm_lap_msg *lap_msg)
+static inline __be32 cm_lap_get_remote_qpn(struct cm_lap_msg *lap_msg)
{
return cpu_to_be32(be32_to_cpu(lap_msg->offset12) >> 8);
}
-static inline void cm_lap_set_remote_qpn(struct cm_lap_msg *lap_msg, u32 qpn)
+static inline void cm_lap_set_remote_qpn(struct cm_lap_msg *lap_msg, __be32 qpn)
{
lap_msg->offset12 = cpu_to_be32((be32_to_cpu(qpn) << 8) |
(be32_to_cpu(lap_msg->offset12) &
@@ -693,17 +691,17 @@
0xFFFFFF07));
}
-static inline u32 cm_lap_get_flow_label(struct cm_lap_msg *lap_msg)
+static inline __be32 cm_lap_get_flow_label(struct cm_lap_msg *lap_msg)
{
- return be32_to_cpu(lap_msg->offset56) >> 12;
+ return cpu_to_be32(be32_to_cpu(lap_msg->offset56) >> 12);
}
static inline void cm_lap_set_flow_label(struct cm_lap_msg *lap_msg,
- u32 flow_label)
+ __be32 flow_label)
{
- lap_msg->offset56 = cpu_to_be32((flow_label << 12) |
- (be32_to_cpu(lap_msg->offset56) &
- 0x00000FFF));
+ lap_msg->offset56 = cpu_to_be32(
+ (be32_to_cpu(lap_msg->offset56) & 0x00000FFF) |
+ (be32_to_cpu(flow_label) << 12));
}
static inline u8 cm_lap_get_traffic_class(struct cm_lap_msg *lap_msg)
@@ -766,8 +764,8 @@
struct cm_apr_msg {
struct ib_mad_hdr hdr;
- u32 local_comm_id;
- u32 remote_comm_id;
+ __be32 local_comm_id;
+ __be32 remote_comm_id;
u8 info_length;
u8 ap_status;
@@ -779,10 +777,10 @@
struct cm_sidr_req_msg {
struct ib_mad_hdr hdr;
- u32 request_id;
- u16 pkey;
- u16 rsvd;
- u64 service_id;
+ __be32 request_id;
+ __be16 pkey;
+ __be16 rsvd;
+ __be64 service_id;
u8 private_data[IB_CM_SIDR_REQ_PRIVATE_DATA_SIZE];
} __attribute__ ((packed));
@@ -790,26 +788,26 @@
struct cm_sidr_rep_msg {
struct ib_mad_hdr hdr;
- u32 request_id;
+ __be32 request_id;
u8 status;
u8 info_length;
- u16 rsvd;
+ __be16 rsvd;
/* QPN:24, rsvd:8 */
- u32 offset8;
- u64 service_id;
- u32 qkey;
+ __be32 offset8;
+ __be64 service_id;
+ __be32 qkey;
u8 info[IB_CM_SIDR_REP_INFO_LENGTH];
u8 private_data[IB_CM_SIDR_REP_PRIVATE_DATA_SIZE];
} __attribute__ ((packed));
-static inline u32 cm_sidr_rep_get_qpn(struct cm_sidr_rep_msg *sidr_rep_msg)
+static inline __be32 cm_sidr_rep_get_qpn(struct cm_sidr_rep_msg *sidr_rep_msg)
{
return cpu_to_be32(be32_to_cpu(sidr_rep_msg->offset8) >> 8);
}
static inline void cm_sidr_rep_set_qpn(struct cm_sidr_rep_msg *sidr_rep_msg,
- u32 qpn)
+ __be32 qpn)
{
sidr_rep_msg->offset8 = cpu_to_be32((be32_to_cpu(qpn) << 8) |
(be32_to_cpu(sidr_rep_msg->offset8) &
diff --git a/drivers/infiniband/core/core_priv.h b/drivers/infiniband/core/core_priv.h
index 7970496..7ad47a4 100644
--- a/drivers/infiniband/core/core_priv.h
+++ b/drivers/infiniband/core/core_priv.h
@@ -38,7 +38,7 @@
#include <linux/list.h>
#include <linux/spinlock.h>
-#include <ib_verbs.h>
+#include <rdma/ib_verbs.h>
int ib_device_register_sysfs(struct ib_device *device);
void ib_device_unregister_sysfs(struct ib_device *device);
diff --git a/drivers/infiniband/core/device.c b/drivers/infiniband/core/device.c
index 9197e92..d3cf84e 100644
--- a/drivers/infiniband/core/device.c
+++ b/drivers/infiniband/core/device.c
@@ -1,5 +1,6 @@
/*
* Copyright (c) 2004 Topspin Communications. All rights reserved.
+ * Copyright (c) 2005 Sun Microsystems, Inc. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
diff --git a/drivers/infiniband/core/fmr_pool.c b/drivers/infiniband/core/fmr_pool.c
index 7763b31..d34a6f1 100644
--- a/drivers/infiniband/core/fmr_pool.c
+++ b/drivers/infiniband/core/fmr_pool.c
@@ -39,7 +39,7 @@
#include <linux/jhash.h>
#include <linux/kthread.h>
-#include <ib_fmr_pool.h>
+#include <rdma/ib_fmr_pool.h>
#include "core_priv.h"
@@ -334,6 +334,7 @@
{
struct ib_pool_fmr *fmr;
struct ib_pool_fmr *tmp;
+ LIST_HEAD(fmr_list);
int i;
kthread_stop(pool->thread);
@@ -341,6 +342,11 @@
i = 0;
list_for_each_entry_safe(fmr, tmp, &pool->free_list, list) {
+ if (fmr->remap_count) {
+ INIT_LIST_HEAD(&fmr_list);
+ list_add_tail(&fmr->fmr->list, &fmr_list);
+ ib_unmap_fmr(&fmr_list);
+ }
ib_dealloc_fmr(fmr->fmr);
list_del(&fmr->list);
kfree(fmr);
diff --git a/drivers/infiniband/core/mad.c b/drivers/infiniband/core/mad.c
index b97e210c..a4a4d9c 100644
--- a/drivers/infiniband/core/mad.c
+++ b/drivers/infiniband/core/mad.c
@@ -693,7 +693,8 @@
goto out;
}
- build_smp_wc(send_wr->wr_id, smp->dr_slid, send_wr->wr.ud.pkey_index,
+ build_smp_wc(send_wr->wr_id, be16_to_cpu(smp->dr_slid),
+ send_wr->wr.ud.pkey_index,
send_wr->wr.ud.port_num, &mad_wc);
/* No GRH for DR SMP */
@@ -1554,7 +1555,7 @@
}
struct ib_mad_send_wr_private*
-ib_find_send_mad(struct ib_mad_agent_private *mad_agent_priv, u64 tid)
+ib_find_send_mad(struct ib_mad_agent_private *mad_agent_priv, __be64 tid)
{
struct ib_mad_send_wr_private *mad_send_wr;
@@ -1597,7 +1598,7 @@
struct ib_mad_send_wr_private *mad_send_wr;
struct ib_mad_send_wc mad_send_wc;
unsigned long flags;
- u64 tid;
+ __be64 tid;
INIT_LIST_HEAD(&mad_recv_wc->rmpp_list);
list_add(&mad_recv_wc->recv_buf.list, &mad_recv_wc->rmpp_list);
@@ -2165,7 +2166,8 @@
* Defined behavior is to complete response
* before request
*/
- build_smp_wc(local->wr_id, IB_LID_PERMISSIVE,
+ build_smp_wc(local->wr_id,
+ be16_to_cpu(IB_LID_PERMISSIVE),
0 /* pkey index */,
recv_mad_agent->agent.port_num, &wc);
@@ -2294,7 +2296,7 @@
spin_unlock_irqrestore(&mad_agent_priv->lock, flags);
}
-static void ib_mad_thread_completion_handler(struct ib_cq *cq)
+static void ib_mad_thread_completion_handler(struct ib_cq *cq, void *arg)
{
struct ib_mad_port_private *port_priv = cq->cq_context;
@@ -2574,8 +2576,7 @@
cq_size = (IB_MAD_QP_SEND_SIZE + IB_MAD_QP_RECV_SIZE) * 2;
port_priv->cq = ib_create_cq(port_priv->device,
- (ib_comp_handler)
- ib_mad_thread_completion_handler,
+ ib_mad_thread_completion_handler,
NULL, port_priv, cq_size);
if (IS_ERR(port_priv->cq)) {
printk(KERN_ERR PFX "Couldn't create ib_mad CQ\n");
diff --git a/drivers/infiniband/core/mad_priv.h b/drivers/infiniband/core/mad_priv.h
index 568da10..f1ba794 100644
--- a/drivers/infiniband/core/mad_priv.h
+++ b/drivers/infiniband/core/mad_priv.h
@@ -40,8 +40,8 @@
#include <linux/pci.h>
#include <linux/kthread.h>
#include <linux/workqueue.h>
-#include <ib_mad.h>
-#include <ib_smi.h>
+#include <rdma/ib_mad.h>
+#include <rdma/ib_smi.h>
#define PFX "ib_mad: "
@@ -121,7 +121,7 @@
struct ib_send_wr send_wr;
struct ib_sge sg_list[IB_MAD_SEND_REQ_MAX_SG];
u64 wr_id; /* client WR ID */
- u64 tid;
+ __be64 tid;
unsigned long timeout;
int retries;
int retry;
@@ -144,7 +144,7 @@
struct ib_send_wr send_wr;
struct ib_sge sg_list[IB_MAD_SEND_REQ_MAX_SG];
u64 wr_id; /* client WR ID */
- u64 tid;
+ __be64 tid;
};
struct ib_mad_mgmt_method_table {
@@ -210,7 +210,7 @@
int ib_send_mad(struct ib_mad_send_wr_private *mad_send_wr);
struct ib_mad_send_wr_private *
-ib_find_send_mad(struct ib_mad_agent_private *mad_agent_priv, u64 tid);
+ib_find_send_mad(struct ib_mad_agent_private *mad_agent_priv, __be64 tid);
void ib_mad_complete_send_wr(struct ib_mad_send_wr_private *mad_send_wr,
struct ib_mad_send_wc *mad_send_wc);
diff --git a/drivers/infiniband/core/mad_rmpp.c b/drivers/infiniband/core/mad_rmpp.c
index 8f1eb80..43fd805 100644
--- a/drivers/infiniband/core/mad_rmpp.c
+++ b/drivers/infiniband/core/mad_rmpp.c
@@ -61,7 +61,7 @@
int seg_num;
int newwin;
- u64 tid;
+ __be64 tid;
u32 src_qp;
u16 slid;
u8 mgmt_class;
@@ -100,6 +100,121 @@
}
}
+static int data_offset(u8 mgmt_class)
+{
+ if (mgmt_class == IB_MGMT_CLASS_SUBN_ADM)
+ return offsetof(struct ib_sa_mad, data);
+ else if ((mgmt_class >= IB_MGMT_CLASS_VENDOR_RANGE2_START) &&
+ (mgmt_class <= IB_MGMT_CLASS_VENDOR_RANGE2_END))
+ return offsetof(struct ib_vendor_mad, data);
+ else
+ return offsetof(struct ib_rmpp_mad, data);
+}
+
+static void format_ack(struct ib_rmpp_mad *ack,
+ struct ib_rmpp_mad *data,
+ struct mad_rmpp_recv *rmpp_recv)
+{
+ unsigned long flags;
+
+ memcpy(&ack->mad_hdr, &data->mad_hdr,
+ data_offset(data->mad_hdr.mgmt_class));
+
+ ack->mad_hdr.method ^= IB_MGMT_METHOD_RESP;
+ ack->rmpp_hdr.rmpp_type = IB_MGMT_RMPP_TYPE_ACK;
+ ib_set_rmpp_flags(&ack->rmpp_hdr, IB_MGMT_RMPP_FLAG_ACTIVE);
+
+ spin_lock_irqsave(&rmpp_recv->lock, flags);
+ rmpp_recv->last_ack = rmpp_recv->seg_num;
+ ack->rmpp_hdr.seg_num = cpu_to_be32(rmpp_recv->seg_num);
+ ack->rmpp_hdr.paylen_newwin = cpu_to_be32(rmpp_recv->newwin);
+ spin_unlock_irqrestore(&rmpp_recv->lock, flags);
+}
+
+static void ack_recv(struct mad_rmpp_recv *rmpp_recv,
+ struct ib_mad_recv_wc *recv_wc)
+{
+ struct ib_mad_send_buf *msg;
+ struct ib_send_wr *bad_send_wr;
+ int hdr_len, ret;
+
+ hdr_len = sizeof(struct ib_mad_hdr) + sizeof(struct ib_rmpp_hdr);
+ msg = ib_create_send_mad(&rmpp_recv->agent->agent, recv_wc->wc->src_qp,
+ recv_wc->wc->pkey_index, rmpp_recv->ah, 1,
+ hdr_len, sizeof(struct ib_rmpp_mad) - hdr_len,
+ GFP_KERNEL);
+ if (!msg)
+ return;
+
+ format_ack((struct ib_rmpp_mad *) msg->mad,
+ (struct ib_rmpp_mad *) recv_wc->recv_buf.mad, rmpp_recv);
+ ret = ib_post_send_mad(&rmpp_recv->agent->agent, &msg->send_wr,
+ &bad_send_wr);
+ if (ret)
+ ib_free_send_mad(msg);
+}
+
+static int alloc_response_msg(struct ib_mad_agent *agent,
+ struct ib_mad_recv_wc *recv_wc,
+ struct ib_mad_send_buf **msg)
+{
+ struct ib_mad_send_buf *m;
+ struct ib_ah *ah;
+ int hdr_len;
+
+ ah = ib_create_ah_from_wc(agent->qp->pd, recv_wc->wc,
+ recv_wc->recv_buf.grh, agent->port_num);
+ if (IS_ERR(ah))
+ return PTR_ERR(ah);
+
+ hdr_len = sizeof(struct ib_mad_hdr) + sizeof(struct ib_rmpp_hdr);
+ m = ib_create_send_mad(agent, recv_wc->wc->src_qp,
+ recv_wc->wc->pkey_index, ah, 1, hdr_len,
+ sizeof(struct ib_rmpp_mad) - hdr_len,
+ GFP_KERNEL);
+ if (IS_ERR(m)) {
+ ib_destroy_ah(ah);
+ return PTR_ERR(m);
+ }
+ *msg = m;
+ return 0;
+}
+
+static void free_msg(struct ib_mad_send_buf *msg)
+{
+ ib_destroy_ah(msg->send_wr.wr.ud.ah);
+ ib_free_send_mad(msg);
+}
+
+static void nack_recv(struct ib_mad_agent_private *agent,
+ struct ib_mad_recv_wc *recv_wc, u8 rmpp_status)
+{
+ struct ib_mad_send_buf *msg;
+ struct ib_rmpp_mad *rmpp_mad;
+ struct ib_send_wr *bad_send_wr;
+ int ret;
+
+ ret = alloc_response_msg(&agent->agent, recv_wc, &msg);
+ if (ret)
+ return;
+
+ rmpp_mad = (struct ib_rmpp_mad *) msg->mad;
+ memcpy(rmpp_mad, recv_wc->recv_buf.mad,
+ data_offset(recv_wc->recv_buf.mad->mad_hdr.mgmt_class));
+
+ rmpp_mad->mad_hdr.method ^= IB_MGMT_METHOD_RESP;
+ rmpp_mad->rmpp_hdr.rmpp_version = IB_MGMT_RMPP_VERSION;
+ rmpp_mad->rmpp_hdr.rmpp_type = IB_MGMT_RMPP_TYPE_ABORT;
+ ib_set_rmpp_flags(&rmpp_mad->rmpp_hdr, IB_MGMT_RMPP_FLAG_ACTIVE);
+ rmpp_mad->rmpp_hdr.rmpp_status = rmpp_status;
+ rmpp_mad->rmpp_hdr.seg_num = 0;
+ rmpp_mad->rmpp_hdr.paylen_newwin = 0;
+
+ ret = ib_post_send_mad(&agent->agent, &msg->send_wr, &bad_send_wr);
+ if (ret)
+ free_msg(msg);
+}
+
static void recv_timeout_handler(void *data)
{
struct mad_rmpp_recv *rmpp_recv = data;
@@ -115,8 +230,8 @@
list_del(&rmpp_recv->list);
spin_unlock_irqrestore(&rmpp_recv->agent->lock, flags);
- /* TODO: send abort. */
rmpp_wc = rmpp_recv->rmpp_wc;
+ nack_recv(rmpp_recv->agent, rmpp_wc, IB_MGMT_RMPP_STATUS_T2L);
destroy_rmpp_recv(rmpp_recv);
ib_free_recv_mad(rmpp_wc);
}
@@ -230,60 +345,6 @@
return cur_rmpp_recv;
}
-static int data_offset(u8 mgmt_class)
-{
- if (mgmt_class == IB_MGMT_CLASS_SUBN_ADM)
- return offsetof(struct ib_sa_mad, data);
- else if ((mgmt_class >= IB_MGMT_CLASS_VENDOR_RANGE2_START) &&
- (mgmt_class <= IB_MGMT_CLASS_VENDOR_RANGE2_END))
- return offsetof(struct ib_vendor_mad, data);
- else
- return offsetof(struct ib_rmpp_mad, data);
-}
-
-static void format_ack(struct ib_rmpp_mad *ack,
- struct ib_rmpp_mad *data,
- struct mad_rmpp_recv *rmpp_recv)
-{
- unsigned long flags;
-
- memcpy(&ack->mad_hdr, &data->mad_hdr,
- data_offset(data->mad_hdr.mgmt_class));
-
- ack->mad_hdr.method ^= IB_MGMT_METHOD_RESP;
- ack->rmpp_hdr.rmpp_type = IB_MGMT_RMPP_TYPE_ACK;
- ib_set_rmpp_flags(&ack->rmpp_hdr, IB_MGMT_RMPP_FLAG_ACTIVE);
-
- spin_lock_irqsave(&rmpp_recv->lock, flags);
- rmpp_recv->last_ack = rmpp_recv->seg_num;
- ack->rmpp_hdr.seg_num = cpu_to_be32(rmpp_recv->seg_num);
- ack->rmpp_hdr.paylen_newwin = cpu_to_be32(rmpp_recv->newwin);
- spin_unlock_irqrestore(&rmpp_recv->lock, flags);
-}
-
-static void ack_recv(struct mad_rmpp_recv *rmpp_recv,
- struct ib_mad_recv_wc *recv_wc)
-{
- struct ib_mad_send_buf *msg;
- struct ib_send_wr *bad_send_wr;
- int hdr_len, ret;
-
- hdr_len = sizeof(struct ib_mad_hdr) + sizeof(struct ib_rmpp_hdr);
- msg = ib_create_send_mad(&rmpp_recv->agent->agent, recv_wc->wc->src_qp,
- recv_wc->wc->pkey_index, rmpp_recv->ah, 1,
- hdr_len, sizeof(struct ib_rmpp_mad) - hdr_len,
- GFP_KERNEL);
- if (!msg)
- return;
-
- format_ack((struct ib_rmpp_mad *) msg->mad,
- (struct ib_rmpp_mad *) recv_wc->recv_buf.mad, rmpp_recv);
- ret = ib_post_send_mad(&rmpp_recv->agent->agent, &msg->send_wr,
- &bad_send_wr);
- if (ret)
- ib_free_send_mad(msg);
-}
-
static inline int get_last_flag(struct ib_mad_recv_buf *seg)
{
struct ib_rmpp_mad *rmpp_mad;
@@ -559,6 +620,34 @@
return ib_send_mad(mad_send_wr);
}
+static void abort_send(struct ib_mad_agent_private *agent, __be64 tid,
+ u8 rmpp_status)
+{
+ struct ib_mad_send_wr_private *mad_send_wr;
+ struct ib_mad_send_wc wc;
+ unsigned long flags;
+
+ spin_lock_irqsave(&agent->lock, flags);
+ mad_send_wr = ib_find_send_mad(agent, tid);
+ if (!mad_send_wr)
+ goto out; /* Unmatched send */
+
+ if ((mad_send_wr->last_ack == mad_send_wr->total_seg) ||
+ (!mad_send_wr->timeout) || (mad_send_wr->status != IB_WC_SUCCESS))
+ goto out; /* Send is already done */
+
+ ib_mark_mad_done(mad_send_wr);
+ spin_unlock_irqrestore(&agent->lock, flags);
+
+ wc.status = IB_WC_REM_ABORT_ERR;
+ wc.vendor_err = rmpp_status;
+ wc.wr_id = mad_send_wr->wr_id;
+ ib_mad_complete_send_wr(mad_send_wr, &wc);
+ return;
+out:
+ spin_unlock_irqrestore(&agent->lock, flags);
+}
+
static void process_rmpp_ack(struct ib_mad_agent_private *agent,
struct ib_mad_recv_wc *mad_recv_wc)
{
@@ -568,11 +657,21 @@
int seg_num, newwin, ret;
rmpp_mad = (struct ib_rmpp_mad *)mad_recv_wc->recv_buf.mad;
- if (rmpp_mad->rmpp_hdr.rmpp_status)
+ if (rmpp_mad->rmpp_hdr.rmpp_status) {
+ abort_send(agent, rmpp_mad->mad_hdr.tid,
+ IB_MGMT_RMPP_STATUS_BAD_STATUS);
+ nack_recv(agent, mad_recv_wc, IB_MGMT_RMPP_STATUS_BAD_STATUS);
return;
+ }
seg_num = be32_to_cpu(rmpp_mad->rmpp_hdr.seg_num);
newwin = be32_to_cpu(rmpp_mad->rmpp_hdr.paylen_newwin);
+ if (newwin < seg_num) {
+ abort_send(agent, rmpp_mad->mad_hdr.tid,
+ IB_MGMT_RMPP_STATUS_W2S);
+ nack_recv(agent, mad_recv_wc, IB_MGMT_RMPP_STATUS_W2S);
+ return;
+ }
spin_lock_irqsave(&agent->lock, flags);
mad_send_wr = ib_find_send_mad(agent, rmpp_mad->mad_hdr.tid);
@@ -583,8 +682,13 @@
(!mad_send_wr->timeout) || (mad_send_wr->status != IB_WC_SUCCESS))
goto out; /* Send is already done */
- if (seg_num > mad_send_wr->total_seg)
- goto out; /* Bad ACK */
+ if (seg_num > mad_send_wr->total_seg || seg_num > mad_send_wr->newwin) {
+ spin_unlock_irqrestore(&agent->lock, flags);
+ abort_send(agent, rmpp_mad->mad_hdr.tid,
+ IB_MGMT_RMPP_STATUS_S2B);
+ nack_recv(agent, mad_recv_wc, IB_MGMT_RMPP_STATUS_S2B);
+ return;
+ }
if (newwin < mad_send_wr->newwin || seg_num < mad_send_wr->last_ack)
goto out; /* Old ACK */
@@ -628,6 +732,72 @@
spin_unlock_irqrestore(&agent->lock, flags);
}
+static struct ib_mad_recv_wc *
+process_rmpp_data(struct ib_mad_agent_private *agent,
+ struct ib_mad_recv_wc *mad_recv_wc)
+{
+ struct ib_rmpp_hdr *rmpp_hdr;
+ u8 rmpp_status;
+
+ rmpp_hdr = &((struct ib_rmpp_mad *)mad_recv_wc->recv_buf.mad)->rmpp_hdr;
+
+ if (rmpp_hdr->rmpp_status) {
+ rmpp_status = IB_MGMT_RMPP_STATUS_BAD_STATUS;
+ goto bad;
+ }
+
+ if (rmpp_hdr->seg_num == __constant_htonl(1)) {
+ if (!(ib_get_rmpp_flags(rmpp_hdr) & IB_MGMT_RMPP_FLAG_FIRST)) {
+ rmpp_status = IB_MGMT_RMPP_STATUS_BAD_SEG;
+ goto bad;
+ }
+ return start_rmpp(agent, mad_recv_wc);
+ } else {
+ if (ib_get_rmpp_flags(rmpp_hdr) & IB_MGMT_RMPP_FLAG_FIRST) {
+ rmpp_status = IB_MGMT_RMPP_STATUS_BAD_SEG;
+ goto bad;
+ }
+ return continue_rmpp(agent, mad_recv_wc);
+ }
+bad:
+ nack_recv(agent, mad_recv_wc, rmpp_status);
+ ib_free_recv_mad(mad_recv_wc);
+ return NULL;
+}
+
+static void process_rmpp_stop(struct ib_mad_agent_private *agent,
+ struct ib_mad_recv_wc *mad_recv_wc)
+{
+ struct ib_rmpp_mad *rmpp_mad;
+
+ rmpp_mad = (struct ib_rmpp_mad *)mad_recv_wc->recv_buf.mad;
+
+ if (rmpp_mad->rmpp_hdr.rmpp_status != IB_MGMT_RMPP_STATUS_RESX) {
+ abort_send(agent, rmpp_mad->mad_hdr.tid,
+ IB_MGMT_RMPP_STATUS_BAD_STATUS);
+ nack_recv(agent, mad_recv_wc, IB_MGMT_RMPP_STATUS_BAD_STATUS);
+ } else
+ abort_send(agent, rmpp_mad->mad_hdr.tid,
+ rmpp_mad->rmpp_hdr.rmpp_status);
+}
+
+static void process_rmpp_abort(struct ib_mad_agent_private *agent,
+ struct ib_mad_recv_wc *mad_recv_wc)
+{
+ struct ib_rmpp_mad *rmpp_mad;
+
+ rmpp_mad = (struct ib_rmpp_mad *)mad_recv_wc->recv_buf.mad;
+
+ if (rmpp_mad->rmpp_hdr.rmpp_status < IB_MGMT_RMPP_STATUS_ABORT_MIN ||
+ rmpp_mad->rmpp_hdr.rmpp_status > IB_MGMT_RMPP_STATUS_ABORT_MAX) {
+ abort_send(agent, rmpp_mad->mad_hdr.tid,
+ IB_MGMT_RMPP_STATUS_BAD_STATUS);
+ nack_recv(agent, mad_recv_wc, IB_MGMT_RMPP_STATUS_BAD_STATUS);
+ } else
+ abort_send(agent, rmpp_mad->mad_hdr.tid,
+ rmpp_mad->rmpp_hdr.rmpp_status);
+}
+
struct ib_mad_recv_wc *
ib_process_rmpp_recv_wc(struct ib_mad_agent_private *agent,
struct ib_mad_recv_wc *mad_recv_wc)
@@ -638,23 +808,29 @@
if (!(rmpp_mad->rmpp_hdr.rmpp_rtime_flags & IB_MGMT_RMPP_FLAG_ACTIVE))
return mad_recv_wc;
- if (rmpp_mad->rmpp_hdr.rmpp_version != IB_MGMT_RMPP_VERSION)
+ if (rmpp_mad->rmpp_hdr.rmpp_version != IB_MGMT_RMPP_VERSION) {
+ abort_send(agent, rmpp_mad->mad_hdr.tid,
+ IB_MGMT_RMPP_STATUS_UNV);
+ nack_recv(agent, mad_recv_wc, IB_MGMT_RMPP_STATUS_UNV);
goto out;
+ }
switch (rmpp_mad->rmpp_hdr.rmpp_type) {
case IB_MGMT_RMPP_TYPE_DATA:
- if (rmpp_mad->rmpp_hdr.seg_num == __constant_htonl(1))
- return start_rmpp(agent, mad_recv_wc);
- else
- return continue_rmpp(agent, mad_recv_wc);
+ return process_rmpp_data(agent, mad_recv_wc);
case IB_MGMT_RMPP_TYPE_ACK:
process_rmpp_ack(agent, mad_recv_wc);
break;
case IB_MGMT_RMPP_TYPE_STOP:
+ process_rmpp_stop(agent, mad_recv_wc);
+ break;
case IB_MGMT_RMPP_TYPE_ABORT:
- /* TODO: process_rmpp_nack(agent, mad_recv_wc); */
+ process_rmpp_abort(agent, mad_recv_wc);
break;
default:
+ abort_send(agent, rmpp_mad->mad_hdr.tid,
+ IB_MGMT_RMPP_STATUS_BADT);
+ nack_recv(agent, mad_recv_wc, IB_MGMT_RMPP_STATUS_BADT);
break;
}
out:
@@ -714,7 +890,10 @@
if (rmpp_mad->rmpp_hdr.rmpp_type != IB_MGMT_RMPP_TYPE_DATA) {
msg = (struct ib_mad_send_buf *) (unsigned long)
mad_send_wc->wr_id;
- ib_free_send_mad(msg);
+ if (rmpp_mad->rmpp_hdr.rmpp_type == IB_MGMT_RMPP_TYPE_ACK)
+ ib_free_send_mad(msg);
+ else
+ free_msg(msg);
return IB_RMPP_RESULT_INTERNAL; /* ACK, STOP, or ABORT */
}
diff --git a/drivers/infiniband/core/packer.c b/drivers/infiniband/core/packer.c
index eb5ff54..35df501 100644
--- a/drivers/infiniband/core/packer.c
+++ b/drivers/infiniband/core/packer.c
@@ -1,5 +1,6 @@
/*
* Copyright (c) 2004 Topspin Corporation. All rights reserved.
+ * Copyright (c) 2005 Sun Microsystems, Inc. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
@@ -32,7 +33,7 @@
* $Id: packer.c 1349 2004-12-16 21:09:43Z roland $
*/
-#include <ib_pack.h>
+#include <rdma/ib_pack.h>
static u64 value_read(int offset, int size, void *structure)
{
diff --git a/drivers/infiniband/core/sa_query.c b/drivers/infiniband/core/sa_query.c
index 7951849..126ac80 100644
--- a/drivers/infiniband/core/sa_query.c
+++ b/drivers/infiniband/core/sa_query.c
@@ -1,6 +1,6 @@
/*
* Copyright (c) 2004 Topspin Communications. All rights reserved.
- * Copyright (c) 2005 Voltaire, Inc. All rights reserved.
+ * Copyright (c) 2005 Voltaire, Inc. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
@@ -44,8 +44,8 @@
#include <linux/kref.h>
#include <linux/idr.h>
-#include <ib_pack.h>
-#include <ib_sa.h>
+#include <rdma/ib_pack.h>
+#include <rdma/ib_sa.h>
MODULE_AUTHOR("Roland Dreier");
MODULE_DESCRIPTION("InfiniBand subnet administration query support");
diff --git a/drivers/infiniband/core/smi.c b/drivers/infiniband/core/smi.c
index b4b2843..35852e7 100644
--- a/drivers/infiniband/core/smi.c
+++ b/drivers/infiniband/core/smi.c
@@ -1,9 +1,10 @@
/*
- * Copyright (c) 2004 Mellanox Technologies Ltd. All rights reserved.
- * Copyright (c) 2004 Infinicon Corporation. All rights reserved.
- * Copyright (c) 2004 Intel Corporation. All rights reserved.
- * Copyright (c) 2004 Topspin Corporation. All rights reserved.
- * Copyright (c) 2004 Voltaire Corporation. All rights reserved.
+ * Copyright (c) 2004, 2005 Mellanox Technologies Ltd. All rights reserved.
+ * Copyright (c) 2004, 2005 Infinicon Corporation. All rights reserved.
+ * Copyright (c) 2004, 2005 Intel Corporation. All rights reserved.
+ * Copyright (c) 2004, 2005 Topspin Corporation. All rights reserved.
+ * Copyright (c) 2004, 2005 Voltaire Corporation. All rights reserved.
+ * Copyright (c) 2005 Sun Microsystems, Inc. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
@@ -36,7 +37,7 @@
* $Id: smi.c 1389 2004-12-27 22:56:47Z roland $
*/
-#include <ib_smi.h>
+#include <rdma/ib_smi.h>
#include "smi.h"
/*
diff --git a/drivers/infiniband/core/sysfs.c b/drivers/infiniband/core/sysfs.c
index 90d51b1..fae1c2d 100644
--- a/drivers/infiniband/core/sysfs.c
+++ b/drivers/infiniband/core/sysfs.c
@@ -1,5 +1,7 @@
/*
* Copyright (c) 2004, 2005 Topspin Communications. All rights reserved.
+ * Copyright (c) 2005 Mellanox Technologies Ltd. All rights reserved.
+ * Copyright (c) 2005 Sun Microsystems, Inc. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
@@ -34,7 +36,7 @@
#include "core_priv.h"
-#include <ib_mad.h>
+#include <rdma/ib_mad.h>
struct ib_port {
struct kobject kobj;
@@ -253,14 +255,14 @@
return ret;
return sprintf(buf, "%04x:%04x:%04x:%04x:%04x:%04x:%04x:%04x\n",
- be16_to_cpu(((u16 *) gid.raw)[0]),
- be16_to_cpu(((u16 *) gid.raw)[1]),
- be16_to_cpu(((u16 *) gid.raw)[2]),
- be16_to_cpu(((u16 *) gid.raw)[3]),
- be16_to_cpu(((u16 *) gid.raw)[4]),
- be16_to_cpu(((u16 *) gid.raw)[5]),
- be16_to_cpu(((u16 *) gid.raw)[6]),
- be16_to_cpu(((u16 *) gid.raw)[7]));
+ be16_to_cpu(((__be16 *) gid.raw)[0]),
+ be16_to_cpu(((__be16 *) gid.raw)[1]),
+ be16_to_cpu(((__be16 *) gid.raw)[2]),
+ be16_to_cpu(((__be16 *) gid.raw)[3]),
+ be16_to_cpu(((__be16 *) gid.raw)[4]),
+ be16_to_cpu(((__be16 *) gid.raw)[5]),
+ be16_to_cpu(((__be16 *) gid.raw)[6]),
+ be16_to_cpu(((__be16 *) gid.raw)[7]));
}
static ssize_t show_port_pkey(struct ib_port *p, struct port_attribute *attr,
@@ -332,11 +334,11 @@
break;
case 16:
ret = sprintf(buf, "%u\n",
- be16_to_cpup((u16 *)(out_mad->data + 40 + offset / 8)));
+ be16_to_cpup((__be16 *)(out_mad->data + 40 + offset / 8)));
break;
case 32:
ret = sprintf(buf, "%u\n",
- be32_to_cpup((u32 *)(out_mad->data + 40 + offset / 8)));
+ be32_to_cpup((__be32 *)(out_mad->data + 40 + offset / 8)));
break;
default:
ret = 0;
@@ -598,10 +600,10 @@
return ret;
return sprintf(buf, "%04x:%04x:%04x:%04x\n",
- be16_to_cpu(((u16 *) &attr.sys_image_guid)[0]),
- be16_to_cpu(((u16 *) &attr.sys_image_guid)[1]),
- be16_to_cpu(((u16 *) &attr.sys_image_guid)[2]),
- be16_to_cpu(((u16 *) &attr.sys_image_guid)[3]));
+ be16_to_cpu(((__be16 *) &attr.sys_image_guid)[0]),
+ be16_to_cpu(((__be16 *) &attr.sys_image_guid)[1]),
+ be16_to_cpu(((__be16 *) &attr.sys_image_guid)[2]),
+ be16_to_cpu(((__be16 *) &attr.sys_image_guid)[3]));
}
static ssize_t show_node_guid(struct class_device *cdev, char *buf)
@@ -615,10 +617,10 @@
return ret;
return sprintf(buf, "%04x:%04x:%04x:%04x\n",
- be16_to_cpu(((u16 *) &attr.node_guid)[0]),
- be16_to_cpu(((u16 *) &attr.node_guid)[1]),
- be16_to_cpu(((u16 *) &attr.node_guid)[2]),
- be16_to_cpu(((u16 *) &attr.node_guid)[3]));
+ be16_to_cpu(((__be16 *) &attr.node_guid)[0]),
+ be16_to_cpu(((__be16 *) &attr.node_guid)[1]),
+ be16_to_cpu(((__be16 *) &attr.node_guid)[2]),
+ be16_to_cpu(((__be16 *) &attr.node_guid)[3]));
}
static CLASS_DEVICE_ATTR(node_type, S_IRUGO, show_node_type, NULL);
diff --git a/drivers/infiniband/core/ucm.c b/drivers/infiniband/core/ucm.c
index 61d07c7..7959582 100644
--- a/drivers/infiniband/core/ucm.c
+++ b/drivers/infiniband/core/ucm.c
@@ -1,5 +1,6 @@
/*
* Copyright (c) 2005 Topspin Communications. All rights reserved.
+ * Copyright (c) 2005 Intel Corporation. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
@@ -73,14 +74,18 @@
static struct idr ctx_id_table;
static int ctx_id_rover = 0;
-static struct ib_ucm_context *ib_ucm_ctx_get(int id)
+static struct ib_ucm_context *ib_ucm_ctx_get(struct ib_ucm_file *file, int id)
{
struct ib_ucm_context *ctx;
down(&ctx_id_mutex);
ctx = idr_find(&ctx_id_table, id);
- if (ctx)
- ctx->ref++;
+ if (!ctx)
+ ctx = ERR_PTR(-ENOENT);
+ else if (ctx->file != file)
+ ctx = ERR_PTR(-EINVAL);
+ else
+ atomic_inc(&ctx->ref);
up(&ctx_id_mutex);
return ctx;
@@ -88,21 +93,37 @@
static void ib_ucm_ctx_put(struct ib_ucm_context *ctx)
{
+ if (atomic_dec_and_test(&ctx->ref))
+ wake_up(&ctx->wait);
+}
+
+static ssize_t ib_ucm_destroy_ctx(struct ib_ucm_file *file, int id)
+{
+ struct ib_ucm_context *ctx;
struct ib_ucm_event *uevent;
down(&ctx_id_mutex);
-
- ctx->ref--;
- if (!ctx->ref)
+ ctx = idr_find(&ctx_id_table, id);
+ if (!ctx)
+ ctx = ERR_PTR(-ENOENT);
+ else if (ctx->file != file)
+ ctx = ERR_PTR(-EINVAL);
+ else
idr_remove(&ctx_id_table, ctx->id);
-
up(&ctx_id_mutex);
- if (ctx->ref)
- return;
+ if (IS_ERR(ctx))
+ return PTR_ERR(ctx);
- down(&ctx->file->mutex);
+ atomic_dec(&ctx->ref);
+ wait_event(ctx->wait, !atomic_read(&ctx->ref));
+ /* No new events will be generated after destroying the cm_id. */
+ if (!IS_ERR(ctx->cm_id))
+ ib_destroy_cm_id(ctx->cm_id);
+
+ /* Cleanup events not yet reported to the user. */
+ down(&file->mutex);
list_del(&ctx->file_list);
while (!list_empty(&ctx->events)) {
@@ -117,13 +138,10 @@
kfree(uevent);
}
+ up(&file->mutex);
- up(&ctx->file->mutex);
-
- ucm_dbg("Destroyed CM ID <%d>\n", ctx->id);
-
- ib_destroy_cm_id(ctx->cm_id);
kfree(ctx);
+ return 0;
}
static struct ib_ucm_context *ib_ucm_ctx_alloc(struct ib_ucm_file *file)
@@ -135,11 +153,11 @@
if (!ctx)
return NULL;
- ctx->ref = 1; /* user reference */
+ atomic_set(&ctx->ref, 1);
+ init_waitqueue_head(&ctx->wait);
ctx->file = file;
INIT_LIST_HEAD(&ctx->events);
- init_MUTEX(&ctx->mutex);
list_add_tail(&ctx->file_list, &file->ctxs);
@@ -177,8 +195,8 @@
if (!kpath || !upath)
return;
- memcpy(upath->dgid, kpath->dgid.raw, sizeof(union ib_gid));
- memcpy(upath->sgid, kpath->sgid.raw, sizeof(union ib_gid));
+ memcpy(upath->dgid, kpath->dgid.raw, sizeof *upath->dgid);
+ memcpy(upath->sgid, kpath->sgid.raw, sizeof *upath->sgid);
upath->dlid = kpath->dlid;
upath->slid = kpath->slid;
@@ -201,10 +219,11 @@
kpath->packet_life_time_selector;
}
-static void ib_ucm_event_req_get(struct ib_ucm_req_event_resp *ureq,
+static void ib_ucm_event_req_get(struct ib_ucm_context *ctx,
+ struct ib_ucm_req_event_resp *ureq,
struct ib_cm_req_event_param *kreq)
{
- ureq->listen_id = (long)kreq->listen_id->context;
+ ureq->listen_id = ctx->id;
ureq->remote_ca_guid = kreq->remote_ca_guid;
ureq->remote_qkey = kreq->remote_qkey;
@@ -240,34 +259,11 @@
urep->srq = krep->srq;
}
-static void ib_ucm_event_rej_get(struct ib_ucm_rej_event_resp *urej,
- struct ib_cm_rej_event_param *krej)
-{
- urej->reason = krej->reason;
-}
-
-static void ib_ucm_event_mra_get(struct ib_ucm_mra_event_resp *umra,
- struct ib_cm_mra_event_param *kmra)
-{
- umra->timeout = kmra->service_timeout;
-}
-
-static void ib_ucm_event_lap_get(struct ib_ucm_lap_event_resp *ulap,
- struct ib_cm_lap_event_param *klap)
-{
- ib_ucm_event_path_get(&ulap->path, klap->alternate_path);
-}
-
-static void ib_ucm_event_apr_get(struct ib_ucm_apr_event_resp *uapr,
- struct ib_cm_apr_event_param *kapr)
-{
- uapr->status = kapr->ap_status;
-}
-
-static void ib_ucm_event_sidr_req_get(struct ib_ucm_sidr_req_event_resp *ureq,
+static void ib_ucm_event_sidr_req_get(struct ib_ucm_context *ctx,
+ struct ib_ucm_sidr_req_event_resp *ureq,
struct ib_cm_sidr_req_event_param *kreq)
{
- ureq->listen_id = (long)kreq->listen_id->context;
+ ureq->listen_id = ctx->id;
ureq->pkey = kreq->pkey;
}
@@ -279,19 +275,18 @@
urep->qpn = krep->qpn;
};
-static int ib_ucm_event_process(struct ib_cm_event *evt,
+static int ib_ucm_event_process(struct ib_ucm_context *ctx,
+ struct ib_cm_event *evt,
struct ib_ucm_event *uvt)
{
void *info = NULL;
- int result;
switch (evt->event) {
case IB_CM_REQ_RECEIVED:
- ib_ucm_event_req_get(&uvt->resp.u.req_resp,
+ ib_ucm_event_req_get(ctx, &uvt->resp.u.req_resp,
&evt->param.req_rcvd);
uvt->data_len = IB_CM_REQ_PRIVATE_DATA_SIZE;
- uvt->resp.present |= (evt->param.req_rcvd.primary_path ?
- IB_UCM_PRES_PRIMARY : 0);
+ uvt->resp.present = IB_UCM_PRES_PRIMARY;
uvt->resp.present |= (evt->param.req_rcvd.alternate_path ?
IB_UCM_PRES_ALTERNATE : 0);
break;
@@ -299,57 +294,46 @@
ib_ucm_event_rep_get(&uvt->resp.u.rep_resp,
&evt->param.rep_rcvd);
uvt->data_len = IB_CM_REP_PRIVATE_DATA_SIZE;
-
break;
case IB_CM_RTU_RECEIVED:
uvt->data_len = IB_CM_RTU_PRIVATE_DATA_SIZE;
uvt->resp.u.send_status = evt->param.send_status;
-
break;
case IB_CM_DREQ_RECEIVED:
uvt->data_len = IB_CM_DREQ_PRIVATE_DATA_SIZE;
uvt->resp.u.send_status = evt->param.send_status;
-
break;
case IB_CM_DREP_RECEIVED:
uvt->data_len = IB_CM_DREP_PRIVATE_DATA_SIZE;
uvt->resp.u.send_status = evt->param.send_status;
-
break;
case IB_CM_MRA_RECEIVED:
- ib_ucm_event_mra_get(&uvt->resp.u.mra_resp,
- &evt->param.mra_rcvd);
+ uvt->resp.u.mra_resp.timeout =
+ evt->param.mra_rcvd.service_timeout;
uvt->data_len = IB_CM_MRA_PRIVATE_DATA_SIZE;
-
break;
case IB_CM_REJ_RECEIVED:
- ib_ucm_event_rej_get(&uvt->resp.u.rej_resp,
- &evt->param.rej_rcvd);
+ uvt->resp.u.rej_resp.reason = evt->param.rej_rcvd.reason;
uvt->data_len = IB_CM_REJ_PRIVATE_DATA_SIZE;
uvt->info_len = evt->param.rej_rcvd.ari_length;
info = evt->param.rej_rcvd.ari;
-
break;
case IB_CM_LAP_RECEIVED:
- ib_ucm_event_lap_get(&uvt->resp.u.lap_resp,
- &evt->param.lap_rcvd);
+ ib_ucm_event_path_get(&uvt->resp.u.lap_resp.path,
+ evt->param.lap_rcvd.alternate_path);
uvt->data_len = IB_CM_LAP_PRIVATE_DATA_SIZE;
- uvt->resp.present |= (evt->param.lap_rcvd.alternate_path ?
- IB_UCM_PRES_ALTERNATE : 0);
+ uvt->resp.present = IB_UCM_PRES_ALTERNATE;
break;
case IB_CM_APR_RECEIVED:
- ib_ucm_event_apr_get(&uvt->resp.u.apr_resp,
- &evt->param.apr_rcvd);
+ uvt->resp.u.apr_resp.status = evt->param.apr_rcvd.ap_status;
uvt->data_len = IB_CM_APR_PRIVATE_DATA_SIZE;
uvt->info_len = evt->param.apr_rcvd.info_len;
info = evt->param.apr_rcvd.apr_info;
-
break;
case IB_CM_SIDR_REQ_RECEIVED:
- ib_ucm_event_sidr_req_get(&uvt->resp.u.sidr_req_resp,
+ ib_ucm_event_sidr_req_get(ctx, &uvt->resp.u.sidr_req_resp,
&evt->param.sidr_req_rcvd);
uvt->data_len = IB_CM_SIDR_REQ_PRIVATE_DATA_SIZE;
-
break;
case IB_CM_SIDR_REP_RECEIVED:
ib_ucm_event_sidr_rep_get(&uvt->resp.u.sidr_rep_resp,
@@ -357,43 +341,35 @@
uvt->data_len = IB_CM_SIDR_REP_PRIVATE_DATA_SIZE;
uvt->info_len = evt->param.sidr_rep_rcvd.info_len;
info = evt->param.sidr_rep_rcvd.info;
-
break;
default:
uvt->resp.u.send_status = evt->param.send_status;
-
break;
}
- if (uvt->data_len && evt->private_data) {
-
+ if (uvt->data_len) {
uvt->data = kmalloc(uvt->data_len, GFP_KERNEL);
- if (!uvt->data) {
- result = -ENOMEM;
- goto error;
- }
+ if (!uvt->data)
+ goto err1;
memcpy(uvt->data, evt->private_data, uvt->data_len);
uvt->resp.present |= IB_UCM_PRES_DATA;
}
- if (uvt->info_len && info) {
-
+ if (uvt->info_len) {
uvt->info = kmalloc(uvt->info_len, GFP_KERNEL);
- if (!uvt->info) {
- result = -ENOMEM;
- goto error;
- }
+ if (!uvt->info)
+ goto err2;
memcpy(uvt->info, info, uvt->info_len);
uvt->resp.present |= IB_UCM_PRES_INFO;
}
-
return 0;
-error:
- kfree(uvt->info);
+
+err2:
kfree(uvt->data);
- return result;
+err1:
+ return -ENOMEM;
}
static int ib_ucm_event_handler(struct ib_cm_id *cm_id,
@@ -403,63 +379,42 @@
struct ib_ucm_context *ctx;
int result = 0;
int id;
- /*
- * lookup correct context based on event type.
- */
- switch (event->event) {
- case IB_CM_REQ_RECEIVED:
- id = (long)event->param.req_rcvd.listen_id->context;
- break;
- case IB_CM_SIDR_REQ_RECEIVED:
- id = (long)event->param.sidr_req_rcvd.listen_id->context;
- break;
- default:
- id = (long)cm_id->context;
- break;
- }
- ucm_dbg("Event. CM ID <%d> event <%d>\n", id, event->event);
-
- ctx = ib_ucm_ctx_get(id);
- if (!ctx)
- return -ENOENT;
+ ctx = cm_id->context;
if (event->event == IB_CM_REQ_RECEIVED ||
event->event == IB_CM_SIDR_REQ_RECEIVED)
id = IB_UCM_CM_ID_INVALID;
+ else
+ id = ctx->id;
uevent = kmalloc(sizeof(*uevent), GFP_KERNEL);
- if (!uevent) {
- result = -ENOMEM;
- goto done;
- }
+ if (!uevent)
+ goto err1;
memset(uevent, 0, sizeof(*uevent));
-
uevent->resp.id = id;
uevent->resp.event = event->event;
- result = ib_ucm_event_process(event, uevent);
+ result = ib_ucm_event_process(ctx, event, uevent);
if (result)
- goto done;
+ goto err2;
uevent->ctx = ctx;
- uevent->cm_id = ((event->event == IB_CM_REQ_RECEIVED ||
- event->event == IB_CM_SIDR_REQ_RECEIVED ) ?
- cm_id : NULL);
+ uevent->cm_id = (id == IB_UCM_CM_ID_INVALID) ? cm_id : NULL;
down(&ctx->file->mutex);
-
list_add_tail(&uevent->file_list, &ctx->file->events);
list_add_tail(&uevent->ctx_list, &ctx->events);
-
wake_up_interruptible(&ctx->file->poll_wait);
-
up(&ctx->file->mutex);
-done:
- ctx->error = result;
- ib_ucm_ctx_put(ctx); /* func reference */
- return result;
+ return 0;
+
+err2:
+ kfree(uevent);
+err1:
+ /* Destroy new cm_id's */
+ return (id == IB_UCM_CM_ID_INVALID);
}
static ssize_t ib_ucm_event(struct ib_ucm_file *file,
@@ -517,9 +472,8 @@
goto done;
}
- ctx->cm_id = uevent->cm_id;
- ctx->cm_id->cm_handler = ib_ucm_event_handler;
- ctx->cm_id->context = (void *)(unsigned long)ctx->id;
+ ctx->cm_id = uevent->cm_id;
+ ctx->cm_id->context = ctx;
uevent->resp.id = ctx->id;
@@ -585,30 +539,29 @@
if (copy_from_user(&cmd, inbuf, sizeof(cmd)))
return -EFAULT;
+ down(&file->mutex);
ctx = ib_ucm_ctx_alloc(file);
+ up(&file->mutex);
if (!ctx)
return -ENOMEM;
- ctx->cm_id = ib_create_cm_id(ib_ucm_event_handler,
- (void *)(unsigned long)ctx->id);
- if (!ctx->cm_id) {
- result = -ENOMEM;
- goto err_cm;
+ ctx->cm_id = ib_create_cm_id(ib_ucm_event_handler, ctx);
+ if (IS_ERR(ctx->cm_id)) {
+ result = PTR_ERR(ctx->cm_id);
+ goto err;
}
resp.id = ctx->id;
if (copy_to_user((void __user *)(unsigned long)cmd.response,
&resp, sizeof(resp))) {
result = -EFAULT;
- goto err_ret;
+ goto err;
}
return 0;
-err_ret:
- ib_destroy_cm_id(ctx->cm_id);
-err_cm:
- ib_ucm_ctx_put(ctx); /* user reference */
+err:
+ ib_ucm_destroy_ctx(file, ctx->id);
return result;
}
@@ -617,19 +570,11 @@
int in_len, int out_len)
{
struct ib_ucm_destroy_id cmd;
- struct ib_ucm_context *ctx;
if (copy_from_user(&cmd, inbuf, sizeof(cmd)))
return -EFAULT;
- ctx = ib_ucm_ctx_get(cmd.id);
- if (!ctx)
- return -ENOENT;
-
- ib_ucm_ctx_put(ctx); /* user reference */
- ib_ucm_ctx_put(ctx); /* func reference */
-
- return 0;
+ return ib_ucm_destroy_ctx(file, cmd.id);
}
static ssize_t ib_ucm_attr_id(struct ib_ucm_file *file,
@@ -647,15 +592,9 @@
if (copy_from_user(&cmd, inbuf, sizeof(cmd)))
return -EFAULT;
- ctx = ib_ucm_ctx_get(cmd.id);
- if (!ctx)
- return -ENOENT;
-
- down(&ctx->file->mutex);
- if (ctx->file != file) {
- result = -EINVAL;
- goto done;
- }
+ ctx = ib_ucm_ctx_get(file, cmd.id);
+ if (IS_ERR(ctx))
+ return PTR_ERR(ctx);
resp.service_id = ctx->cm_id->service_id;
resp.service_mask = ctx->cm_id->service_mask;
@@ -666,9 +605,7 @@
&resp, sizeof(resp)))
result = -EFAULT;
-done:
- up(&ctx->file->mutex);
- ib_ucm_ctx_put(ctx); /* func reference */
+ ib_ucm_ctx_put(ctx);
return result;
}
@@ -683,19 +620,12 @@
if (copy_from_user(&cmd, inbuf, sizeof(cmd)))
return -EFAULT;
- ctx = ib_ucm_ctx_get(cmd.id);
- if (!ctx)
- return -ENOENT;
+ ctx = ib_ucm_ctx_get(file, cmd.id);
+ if (IS_ERR(ctx))
+ return PTR_ERR(ctx);
- down(&ctx->file->mutex);
- if (ctx->file != file)
- result = -EINVAL;
- else
- result = ib_cm_listen(ctx->cm_id, cmd.service_id,
- cmd.service_mask);
-
- up(&ctx->file->mutex);
- ib_ucm_ctx_put(ctx); /* func reference */
+ result = ib_cm_listen(ctx->cm_id, cmd.service_id, cmd.service_mask);
+ ib_ucm_ctx_put(ctx);
return result;
}
@@ -710,18 +640,12 @@
if (copy_from_user(&cmd, inbuf, sizeof(cmd)))
return -EFAULT;
- ctx = ib_ucm_ctx_get(cmd.id);
- if (!ctx)
- return -ENOENT;
+ ctx = ib_ucm_ctx_get(file, cmd.id);
+ if (IS_ERR(ctx))
+ return PTR_ERR(ctx);
- down(&ctx->file->mutex);
- if (ctx->file != file)
- result = -EINVAL;
- else
- result = ib_cm_establish(ctx->cm_id);
-
- up(&ctx->file->mutex);
- ib_ucm_ctx_put(ctx); /* func reference */
+ result = ib_cm_establish(ctx->cm_id);
+ ib_ucm_ctx_put(ctx);
return result;
}
@@ -768,8 +692,8 @@
return -EFAULT;
}
- memcpy(sa_path->dgid.raw, ucm_path.dgid, sizeof(union ib_gid));
- memcpy(sa_path->sgid.raw, ucm_path.sgid, sizeof(union ib_gid));
+ memcpy(sa_path->dgid.raw, ucm_path.dgid, sizeof sa_path->dgid);
+ memcpy(sa_path->sgid.raw, ucm_path.sgid, sizeof sa_path->sgid);
sa_path->dlid = ucm_path.dlid;
sa_path->slid = ucm_path.slid;
@@ -839,25 +763,17 @@
param.max_cm_retries = cmd.max_cm_retries;
param.srq = cmd.srq;
- ctx = ib_ucm_ctx_get(cmd.id);
- if (!ctx) {
- result = -ENOENT;
- goto done;
- }
-
- down(&ctx->file->mutex);
- if (ctx->file != file)
- result = -EINVAL;
- else
+ ctx = ib_ucm_ctx_get(file, cmd.id);
+ if (!IS_ERR(ctx)) {
result = ib_send_cm_req(ctx->cm_id, ¶m);
+ ib_ucm_ctx_put(ctx);
+ } else
+ result = PTR_ERR(ctx);
- up(&ctx->file->mutex);
- ib_ucm_ctx_put(ctx); /* func reference */
done:
kfree(param.private_data);
kfree(param.primary_path);
kfree(param.alternate_path);
-
return result;
}
@@ -890,23 +806,14 @@
param.rnr_retry_count = cmd.rnr_retry_count;
param.srq = cmd.srq;
- ctx = ib_ucm_ctx_get(cmd.id);
- if (!ctx) {
- result = -ENOENT;
- goto done;
- }
-
- down(&ctx->file->mutex);
- if (ctx->file != file)
- result = -EINVAL;
- else
+ ctx = ib_ucm_ctx_get(file, cmd.id);
+ if (!IS_ERR(ctx)) {
result = ib_send_cm_rep(ctx->cm_id, ¶m);
+ ib_ucm_ctx_put(ctx);
+ } else
+ result = PTR_ERR(ctx);
- up(&ctx->file->mutex);
- ib_ucm_ctx_put(ctx); /* func reference */
-done:
kfree(param.private_data);
-
return result;
}
@@ -928,23 +835,14 @@
if (result)
return result;
- ctx = ib_ucm_ctx_get(cmd.id);
- if (!ctx) {
- result = -ENOENT;
- goto done;
- }
-
- down(&ctx->file->mutex);
- if (ctx->file != file)
- result = -EINVAL;
- else
+ ctx = ib_ucm_ctx_get(file, cmd.id);
+ if (!IS_ERR(ctx)) {
result = func(ctx->cm_id, private_data, cmd.len);
+ ib_ucm_ctx_put(ctx);
+ } else
+ result = PTR_ERR(ctx);
- up(&ctx->file->mutex);
- ib_ucm_ctx_put(ctx); /* func reference */
-done:
kfree(private_data);
-
return result;
}
@@ -995,26 +893,17 @@
if (result)
goto done;
- ctx = ib_ucm_ctx_get(cmd.id);
- if (!ctx) {
- result = -ENOENT;
- goto done;
- }
-
- down(&ctx->file->mutex);
- if (ctx->file != file)
- result = -EINVAL;
- else
- result = func(ctx->cm_id, cmd.status,
- info, cmd.info_len,
+ ctx = ib_ucm_ctx_get(file, cmd.id);
+ if (!IS_ERR(ctx)) {
+ result = func(ctx->cm_id, cmd.status, info, cmd.info_len,
data, cmd.data_len);
+ ib_ucm_ctx_put(ctx);
+ } else
+ result = PTR_ERR(ctx);
- up(&ctx->file->mutex);
- ib_ucm_ctx_put(ctx); /* func reference */
done:
kfree(data);
kfree(info);
-
return result;
}
@@ -1048,24 +937,14 @@
if (result)
return result;
- ctx = ib_ucm_ctx_get(cmd.id);
- if (!ctx) {
- result = -ENOENT;
- goto done;
- }
+ ctx = ib_ucm_ctx_get(file, cmd.id);
+ if (!IS_ERR(ctx)) {
+ result = ib_send_cm_mra(ctx->cm_id, cmd.timeout, data, cmd.len);
+ ib_ucm_ctx_put(ctx);
+ } else
+ result = PTR_ERR(ctx);
- down(&ctx->file->mutex);
- if (ctx->file != file)
- result = -EINVAL;
- else
- result = ib_send_cm_mra(ctx->cm_id, cmd.timeout,
- data, cmd.len);
-
- up(&ctx->file->mutex);
- ib_ucm_ctx_put(ctx); /* func reference */
-done:
kfree(data);
-
return result;
}
@@ -1090,24 +969,16 @@
if (result)
goto done;
- ctx = ib_ucm_ctx_get(cmd.id);
- if (!ctx) {
- result = -ENOENT;
- goto done;
- }
-
- down(&ctx->file->mutex);
- if (ctx->file != file)
- result = -EINVAL;
- else
+ ctx = ib_ucm_ctx_get(file, cmd.id);
+ if (!IS_ERR(ctx)) {
result = ib_send_cm_lap(ctx->cm_id, path, data, cmd.len);
+ ib_ucm_ctx_put(ctx);
+ } else
+ result = PTR_ERR(ctx);
- up(&ctx->file->mutex);
- ib_ucm_ctx_put(ctx); /* func reference */
done:
kfree(data);
kfree(path);
-
return result;
}
@@ -1140,24 +1011,16 @@
param.max_cm_retries = cmd.max_cm_retries;
param.pkey = cmd.pkey;
- ctx = ib_ucm_ctx_get(cmd.id);
- if (!ctx) {
- result = -ENOENT;
- goto done;
- }
-
- down(&ctx->file->mutex);
- if (ctx->file != file)
- result = -EINVAL;
- else
+ ctx = ib_ucm_ctx_get(file, cmd.id);
+ if (!IS_ERR(ctx)) {
result = ib_send_cm_sidr_req(ctx->cm_id, ¶m);
+ ib_ucm_ctx_put(ctx);
+ } else
+ result = PTR_ERR(ctx);
- up(&ctx->file->mutex);
- ib_ucm_ctx_put(ctx); /* func reference */
done:
kfree(param.private_data);
kfree(param.path);
-
return result;
}
@@ -1184,30 +1047,22 @@
if (result)
goto done;
- param.qp_num = cmd.qpn;
- param.qkey = cmd.qkey;
- param.status = cmd.status;
- param.info_length = cmd.info_len;
- param.private_data_len = cmd.data_len;
+ param.qp_num = cmd.qpn;
+ param.qkey = cmd.qkey;
+ param.status = cmd.status;
+ param.info_length = cmd.info_len;
+ param.private_data_len = cmd.data_len;
- ctx = ib_ucm_ctx_get(cmd.id);
- if (!ctx) {
- result = -ENOENT;
- goto done;
- }
-
- down(&ctx->file->mutex);
- if (ctx->file != file)
- result = -EINVAL;
- else
+ ctx = ib_ucm_ctx_get(file, cmd.id);
+ if (!IS_ERR(ctx)) {
result = ib_send_cm_sidr_rep(ctx->cm_id, ¶m);
+ ib_ucm_ctx_put(ctx);
+ } else
+ result = PTR_ERR(ctx);
- up(&ctx->file->mutex);
- ib_ucm_ctx_put(ctx); /* func reference */
done:
kfree(param.private_data);
kfree(param.info);
-
return result;
}
@@ -1305,22 +1160,17 @@
struct ib_ucm_context *ctx;
down(&file->mutex);
-
while (!list_empty(&file->ctxs)) {
ctx = list_entry(file->ctxs.next,
struct ib_ucm_context, file_list);
- up(&ctx->file->mutex);
- ib_ucm_ctx_put(ctx); /* user reference */
+ up(&file->mutex);
+ ib_ucm_destroy_ctx(file, ctx->id);
down(&file->mutex);
}
-
up(&file->mutex);
-
kfree(file);
-
- ucm_dbg("Deleted struct\n");
return 0;
}
diff --git a/drivers/infiniband/core/ucm.h b/drivers/infiniband/core/ucm.h
index 6d36606..c8819b9 100644
--- a/drivers/infiniband/core/ucm.h
+++ b/drivers/infiniband/core/ucm.h
@@ -40,17 +40,15 @@
#include <linux/cdev.h>
#include <linux/idr.h>
-#include <ib_cm.h>
-#include <ib_user_cm.h>
+#include <rdma/ib_cm.h>
+#include <rdma/ib_user_cm.h>
#define IB_UCM_CM_ID_INVALID 0xffffffff
struct ib_ucm_file {
struct semaphore mutex;
struct file *filp;
- /*
- * list of pending events
- */
+
struct list_head ctxs; /* list of active connections */
struct list_head events; /* list of pending events */
wait_queue_head_t poll_wait;
@@ -58,12 +56,11 @@
struct ib_ucm_context {
int id;
- int ref;
- int error;
+ wait_queue_head_t wait;
+ atomic_t ref;
struct ib_ucm_file *file;
struct ib_cm_id *cm_id;
- struct semaphore mutex;
struct list_head events; /* list of pending events. */
struct list_head file_list; /* member in file ctx list */
diff --git a/drivers/infiniband/core/ud_header.c b/drivers/infiniband/core/ud_header.c
index dc4eb1d..527b234 100644
--- a/drivers/infiniband/core/ud_header.c
+++ b/drivers/infiniband/core/ud_header.c
@@ -1,5 +1,6 @@
/*
* Copyright (c) 2004 Topspin Corporation. All rights reserved.
+ * Copyright (c) 2005 Sun Microsystems, Inc. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
@@ -34,7 +35,7 @@
#include <linux/errno.h>
-#include <ib_pack.h>
+#include <rdma/ib_pack.h>
#define STRUCT_FIELD(header, field) \
.struct_offset_bytes = offsetof(struct ib_unpacked_ ## header, field), \
@@ -194,6 +195,7 @@
struct ib_ud_header *header)
{
int header_len;
+ u16 packet_length;
memset(header, 0, sizeof *header);
@@ -208,7 +210,7 @@
header->lrh.link_version = 0;
header->lrh.link_next_header =
grh_present ? IB_LNH_IBA_GLOBAL : IB_LNH_IBA_LOCAL;
- header->lrh.packet_length = (IB_LRH_BYTES +
+ packet_length = (IB_LRH_BYTES +
IB_BTH_BYTES +
IB_DETH_BYTES +
payload_bytes +
@@ -217,8 +219,7 @@
header->grh_present = grh_present;
if (grh_present) {
- header->lrh.packet_length += IB_GRH_BYTES / 4;
-
+ packet_length += IB_GRH_BYTES / 4;
header->grh.ip_version = 6;
header->grh.payload_length =
cpu_to_be16((IB_BTH_BYTES +
@@ -229,7 +230,7 @@
header->grh.next_header = 0x1b;
}
- cpu_to_be16s(&header->lrh.packet_length);
+ header->lrh.packet_length = cpu_to_be16(packet_length);
if (header->immediate_present)
header->bth.opcode = IB_OPCODE_UD_SEND_ONLY_WITH_IMMEDIATE;
diff --git a/drivers/infiniband/core/user_mad.c b/drivers/infiniband/core/user_mad.c
index 2e38792..7c2f030 100644
--- a/drivers/infiniband/core/user_mad.c
+++ b/drivers/infiniband/core/user_mad.c
@@ -1,6 +1,6 @@
/*
* Copyright (c) 2004 Topspin Communications. All rights reserved.
- * Copyright (c) 2005 Voltaire, Inc. All rights reserved.
+ * Copyright (c) 2005 Voltaire, Inc. All rights reserved.
* Copyright (c) 2005 Sun Microsystems, Inc. All rights reserved.
*
* This software is available to you under a choice of one of two
@@ -49,8 +49,8 @@
#include <asm/uaccess.h>
#include <asm/semaphore.h>
-#include <ib_mad.h>
-#include <ib_user_mad.h>
+#include <rdma/ib_mad.h>
+#include <rdma/ib_user_mad.h>
MODULE_AUTHOR("Roland Dreier");
MODULE_DESCRIPTION("InfiniBand userspace MAD packet access");
@@ -271,7 +271,7 @@
struct ib_send_wr *bad_wr;
struct ib_rmpp_mad *rmpp_mad;
u8 method;
- u64 *tid;
+ __be64 *tid;
int ret, length, hdr_len, data_len, rmpp_hdr_size;
int rmpp_active = 0;
@@ -316,7 +316,7 @@
if (packet->mad.hdr.grh_present) {
ah_attr.ah_flags = IB_AH_GRH;
memcpy(ah_attr.grh.dgid.raw, packet->mad.hdr.gid, 16);
- ah_attr.grh.flow_label = packet->mad.hdr.flow_label;
+ ah_attr.grh.flow_label = be32_to_cpu(packet->mad.hdr.flow_label);
ah_attr.grh.hop_limit = packet->mad.hdr.hop_limit;
ah_attr.grh.traffic_class = packet->mad.hdr.traffic_class;
}
diff --git a/drivers/infiniband/core/uverbs.h b/drivers/infiniband/core/uverbs.h
index 7696022..180b3d4 100644
--- a/drivers/infiniband/core/uverbs.h
+++ b/drivers/infiniband/core/uverbs.h
@@ -1,6 +1,8 @@
/*
* Copyright (c) 2005 Topspin Communications. All rights reserved.
* Copyright (c) 2005 Cisco Systems. All rights reserved.
+ * Copyright (c) 2005 Mellanox Technologies. All rights reserved.
+ * Copyright (c) 2005 Voltaire, Inc. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
@@ -43,8 +45,8 @@
#include <linux/kref.h>
#include <linux/idr.h>
-#include <ib_verbs.h>
-#include <ib_user_verbs.h>
+#include <rdma/ib_verbs.h>
+#include <rdma/ib_user_verbs.h>
struct ib_uverbs_device {
int devnum;
@@ -97,10 +99,12 @@
extern struct idr ib_uverbs_ah_idr;
extern struct idr ib_uverbs_cq_idr;
extern struct idr ib_uverbs_qp_idr;
+extern struct idr ib_uverbs_srq_idr;
void ib_uverbs_comp_handler(struct ib_cq *cq, void *cq_context);
void ib_uverbs_cq_event_handler(struct ib_event *event, void *context_ptr);
void ib_uverbs_qp_event_handler(struct ib_event *event, void *context_ptr);
+void ib_uverbs_srq_event_handler(struct ib_event *event, void *context_ptr);
int ib_umem_get(struct ib_device *dev, struct ib_umem *mem,
void *addr, size_t size, int write);
@@ -129,5 +133,8 @@
IB_UVERBS_DECLARE_CMD(destroy_qp);
IB_UVERBS_DECLARE_CMD(attach_mcast);
IB_UVERBS_DECLARE_CMD(detach_mcast);
+IB_UVERBS_DECLARE_CMD(create_srq);
+IB_UVERBS_DECLARE_CMD(modify_srq);
+IB_UVERBS_DECLARE_CMD(destroy_srq);
#endif /* UVERBS_H */
diff --git a/drivers/infiniband/core/uverbs_cmd.c b/drivers/infiniband/core/uverbs_cmd.c
index 5f2bbcd..ebccf9f 100644
--- a/drivers/infiniband/core/uverbs_cmd.c
+++ b/drivers/infiniband/core/uverbs_cmd.c
@@ -724,6 +724,7 @@
struct ib_uobject *uobj;
struct ib_pd *pd;
struct ib_cq *scq, *rcq;
+ struct ib_srq *srq;
struct ib_qp *qp;
struct ib_qp_init_attr attr;
int ret;
@@ -747,10 +748,12 @@
pd = idr_find(&ib_uverbs_pd_idr, cmd.pd_handle);
scq = idr_find(&ib_uverbs_cq_idr, cmd.send_cq_handle);
rcq = idr_find(&ib_uverbs_cq_idr, cmd.recv_cq_handle);
+ srq = cmd.is_srq ? idr_find(&ib_uverbs_srq_idr, cmd.srq_handle) : NULL;
if (!pd || pd->uobject->context != file->ucontext ||
!scq || scq->uobject->context != file->ucontext ||
- !rcq || rcq->uobject->context != file->ucontext) {
+ !rcq || rcq->uobject->context != file->ucontext ||
+ (cmd.is_srq && (!srq || srq->uobject->context != file->ucontext))) {
ret = -EINVAL;
goto err_up;
}
@@ -759,7 +762,7 @@
attr.qp_context = file;
attr.send_cq = scq;
attr.recv_cq = rcq;
- attr.srq = NULL;
+ attr.srq = srq;
attr.sq_sig_type = cmd.sq_sig_all ? IB_SIGNAL_ALL_WR : IB_SIGNAL_REQ_WR;
attr.qp_type = cmd.qp_type;
@@ -1004,3 +1007,178 @@
return ret ? ret : in_len;
}
+
+ssize_t ib_uverbs_create_srq(struct ib_uverbs_file *file,
+ const char __user *buf, int in_len,
+ int out_len)
+{
+ struct ib_uverbs_create_srq cmd;
+ struct ib_uverbs_create_srq_resp resp;
+ struct ib_udata udata;
+ struct ib_uobject *uobj;
+ struct ib_pd *pd;
+ struct ib_srq *srq;
+ struct ib_srq_init_attr attr;
+ int ret;
+
+ if (out_len < sizeof resp)
+ return -ENOSPC;
+
+ if (copy_from_user(&cmd, buf, sizeof cmd))
+ return -EFAULT;
+
+ INIT_UDATA(&udata, buf + sizeof cmd,
+ (unsigned long) cmd.response + sizeof resp,
+ in_len - sizeof cmd, out_len - sizeof resp);
+
+ uobj = kmalloc(sizeof *uobj, GFP_KERNEL);
+ if (!uobj)
+ return -ENOMEM;
+
+ down(&ib_uverbs_idr_mutex);
+
+ pd = idr_find(&ib_uverbs_pd_idr, cmd.pd_handle);
+
+ if (!pd || pd->uobject->context != file->ucontext) {
+ ret = -EINVAL;
+ goto err_up;
+ }
+
+ attr.event_handler = ib_uverbs_srq_event_handler;
+ attr.srq_context = file;
+ attr.attr.max_wr = cmd.max_wr;
+ attr.attr.max_sge = cmd.max_sge;
+ attr.attr.srq_limit = cmd.srq_limit;
+
+ uobj->user_handle = cmd.user_handle;
+ uobj->context = file->ucontext;
+
+ srq = pd->device->create_srq(pd, &attr, &udata);
+ if (IS_ERR(srq)) {
+ ret = PTR_ERR(srq);
+ goto err_up;
+ }
+
+ srq->device = pd->device;
+ srq->pd = pd;
+ srq->uobject = uobj;
+ srq->event_handler = attr.event_handler;
+ srq->srq_context = attr.srq_context;
+ atomic_inc(&pd->usecnt);
+ atomic_set(&srq->usecnt, 0);
+
+ memset(&resp, 0, sizeof resp);
+
+retry:
+ if (!idr_pre_get(&ib_uverbs_srq_idr, GFP_KERNEL)) {
+ ret = -ENOMEM;
+ goto err_destroy;
+ }
+
+ ret = idr_get_new(&ib_uverbs_srq_idr, srq, &uobj->id);
+
+ if (ret == -EAGAIN)
+ goto retry;
+ if (ret)
+ goto err_destroy;
+
+ resp.srq_handle = uobj->id;
+
+ spin_lock_irq(&file->ucontext->lock);
+ list_add_tail(&uobj->list, &file->ucontext->srq_list);
+ spin_unlock_irq(&file->ucontext->lock);
+
+ if (copy_to_user((void __user *) (unsigned long) cmd.response,
+ &resp, sizeof resp)) {
+ ret = -EFAULT;
+ goto err_list;
+ }
+
+ up(&ib_uverbs_idr_mutex);
+
+ return in_len;
+
+err_list:
+ spin_lock_irq(&file->ucontext->lock);
+ list_del(&uobj->list);
+ spin_unlock_irq(&file->ucontext->lock);
+
+err_destroy:
+ ib_destroy_srq(srq);
+
+err_up:
+ up(&ib_uverbs_idr_mutex);
+
+ kfree(uobj);
+ return ret;
+}
+
+ssize_t ib_uverbs_modify_srq(struct ib_uverbs_file *file,
+ const char __user *buf, int in_len,
+ int out_len)
+{
+ struct ib_uverbs_modify_srq cmd;
+ struct ib_srq *srq;
+ struct ib_srq_attr attr;
+ int ret;
+
+ if (copy_from_user(&cmd, buf, sizeof cmd))
+ return -EFAULT;
+
+ down(&ib_uverbs_idr_mutex);
+
+ srq = idr_find(&ib_uverbs_srq_idr, cmd.srq_handle);
+ if (!srq || srq->uobject->context != file->ucontext) {
+ ret = -EINVAL;
+ goto out;
+ }
+
+ attr.max_wr = cmd.max_wr;
+ attr.max_sge = cmd.max_sge;
+ attr.srq_limit = cmd.srq_limit;
+
+ ret = ib_modify_srq(srq, &attr, cmd.attr_mask);
+
+out:
+ up(&ib_uverbs_idr_mutex);
+
+ return ret ? ret : in_len;
+}
+
+ssize_t ib_uverbs_destroy_srq(struct ib_uverbs_file *file,
+ const char __user *buf, int in_len,
+ int out_len)
+{
+ struct ib_uverbs_destroy_srq cmd;
+ struct ib_srq *srq;
+ struct ib_uobject *uobj;
+ int ret = -EINVAL;
+
+ if (copy_from_user(&cmd, buf, sizeof cmd))
+ return -EFAULT;
+
+ down(&ib_uverbs_idr_mutex);
+
+ srq = idr_find(&ib_uverbs_srq_idr, cmd.srq_handle);
+ if (!srq || srq->uobject->context != file->ucontext)
+ goto out;
+
+ uobj = srq->uobject;
+
+ ret = ib_destroy_srq(srq);
+ if (ret)
+ goto out;
+
+ idr_remove(&ib_uverbs_srq_idr, cmd.srq_handle);
+
+ spin_lock_irq(&file->ucontext->lock);
+ list_del(&uobj->list);
+ spin_unlock_irq(&file->ucontext->lock);
+
+ kfree(uobj);
+
+out:
+ up(&ib_uverbs_idr_mutex);
+
+ return ret ? ret : in_len;
+}
diff --git a/drivers/infiniband/core/uverbs_main.c b/drivers/infiniband/core/uverbs_main.c
index eb99e69..09caf5b 100644
--- a/drivers/infiniband/core/uverbs_main.c
+++ b/drivers/infiniband/core/uverbs_main.c
@@ -1,6 +1,8 @@
/*
* Copyright (c) 2005 Topspin Communications. All rights reserved.
* Copyright (c) 2005 Cisco Systems. All rights reserved.
+ * Copyright (c) 2005 Mellanox Technologies. All rights reserved.
+ * Copyright (c) 2005 Voltaire, Inc. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
@@ -67,6 +69,7 @@
DEFINE_IDR(ib_uverbs_ah_idr);
DEFINE_IDR(ib_uverbs_cq_idr);
DEFINE_IDR(ib_uverbs_qp_idr);
+DEFINE_IDR(ib_uverbs_srq_idr);
static spinlock_t map_lock;
static DECLARE_BITMAP(dev_map, IB_UVERBS_MAX_DEVICES);
@@ -91,6 +94,9 @@
[IB_USER_VERBS_CMD_DESTROY_QP] = ib_uverbs_destroy_qp,
[IB_USER_VERBS_CMD_ATTACH_MCAST] = ib_uverbs_attach_mcast,
[IB_USER_VERBS_CMD_DETACH_MCAST] = ib_uverbs_detach_mcast,
+ [IB_USER_VERBS_CMD_CREATE_SRQ] = ib_uverbs_create_srq,
+ [IB_USER_VERBS_CMD_MODIFY_SRQ] = ib_uverbs_modify_srq,
+ [IB_USER_VERBS_CMD_DESTROY_SRQ] = ib_uverbs_destroy_srq,
};
static struct vfsmount *uverbs_event_mnt;
@@ -125,18 +131,26 @@
kfree(uobj);
}
- /* XXX Free SRQs */
+ list_for_each_entry_safe(uobj, tmp, &context->srq_list, list) {
+ struct ib_srq *srq = idr_find(&ib_uverbs_srq_idr, uobj->id);
+ idr_remove(&ib_uverbs_srq_idr, uobj->id);
+ ib_destroy_srq(srq);
+ list_del(&uobj->list);
+ kfree(uobj);
+ }
+
/* XXX Free MWs */
list_for_each_entry_safe(uobj, tmp, &context->mr_list, list) {
struct ib_mr *mr = idr_find(&ib_uverbs_mr_idr, uobj->id);
+ struct ib_device *mrdev = mr->device;
struct ib_umem_object *memobj;
idr_remove(&ib_uverbs_mr_idr, uobj->id);
ib_dereg_mr(mr);
memobj = container_of(uobj, struct ib_umem_object, uobject);
- ib_umem_release_on_close(mr->device, &memobj->umem);
+ ib_umem_release_on_close(mrdev, &memobj->umem);
list_del(&uobj->list);
kfree(memobj);
@@ -343,6 +357,13 @@
event->event);
}
+void ib_uverbs_srq_event_handler(struct ib_event *event, void *context_ptr)
+{
+ ib_uverbs_async_handler(context_ptr,
+ event->element.srq->uobject->user_handle,
+ event->event);
+}
+
static void ib_uverbs_event_handler(struct ib_event_handler *handler,
struct ib_event *event)
{
diff --git a/drivers/infiniband/core/uverbs_mem.c b/drivers/infiniband/core/uverbs_mem.c
index ed550f6..36a32c3 100644
--- a/drivers/infiniband/core/uverbs_mem.c
+++ b/drivers/infiniband/core/uverbs_mem.c
@@ -1,6 +1,7 @@
/*
* Copyright (c) 2005 Topspin Communications. All rights reserved.
* Copyright (c) 2005 Cisco Systems. All rights reserved.
+ * Copyright (c) 2005 Mellanox Technologies. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
diff --git a/drivers/infiniband/core/verbs.c b/drivers/infiniband/core/verbs.c
index 506fdf1..5081d90 100644
--- a/drivers/infiniband/core/verbs.c
+++ b/drivers/infiniband/core/verbs.c
@@ -4,6 +4,7 @@
* Copyright (c) 2004 Intel Corporation. All rights reserved.
* Copyright (c) 2004 Topspin Corporation. All rights reserved.
* Copyright (c) 2004 Voltaire Corporation. All rights reserved.
+ * Copyright (c) 2005 Sun Microsystems, Inc. All rights reserved.
* Copyright (c) 2005 Cisco Systems. All rights reserved.
*
* This software is available to you under a choice of one of two
@@ -40,8 +41,8 @@
#include <linux/errno.h>
#include <linux/err.h>
-#include <ib_verbs.h>
-#include <ib_cache.h>
+#include <rdma/ib_verbs.h>
+#include <rdma/ib_cache.h>
/* Protection domains */
@@ -153,6 +154,66 @@
}
EXPORT_SYMBOL(ib_destroy_ah);
+/* Shared receive queues */
+
+struct ib_srq *ib_create_srq(struct ib_pd *pd,
+ struct ib_srq_init_attr *srq_init_attr)
+{
+ struct ib_srq *srq;
+
+ if (!pd->device->create_srq)
+ return ERR_PTR(-ENOSYS);
+
+ srq = pd->device->create_srq(pd, srq_init_attr, NULL);
+
+ if (!IS_ERR(srq)) {
+ srq->device = pd->device;
+ srq->pd = pd;
+ srq->uobject = NULL;
+ srq->event_handler = srq_init_attr->event_handler;
+ srq->srq_context = srq_init_attr->srq_context;
+ atomic_inc(&pd->usecnt);
+ atomic_set(&srq->usecnt, 0);
+ }
+
+ return srq;
+}
+EXPORT_SYMBOL(ib_create_srq);
+
+int ib_modify_srq(struct ib_srq *srq,
+ struct ib_srq_attr *srq_attr,
+ enum ib_srq_attr_mask srq_attr_mask)
+{
+ return srq->device->modify_srq(srq, srq_attr, srq_attr_mask);
+}
+EXPORT_SYMBOL(ib_modify_srq);
+
+int ib_query_srq(struct ib_srq *srq,
+ struct ib_srq_attr *srq_attr)
+{
+ return srq->device->query_srq ?
+ srq->device->query_srq(srq, srq_attr) : -ENOSYS;
+}
+EXPORT_SYMBOL(ib_query_srq);
+
+int ib_destroy_srq(struct ib_srq *srq)
+{
+ struct ib_pd *pd;
+ int ret;
+
+ if (atomic_read(&srq->usecnt))
+ return -EBUSY;
+
+ pd = srq->pd;
+
+ ret = srq->device->destroy_srq(srq);
+ if (!ret)
+ atomic_dec(&pd->usecnt);
+
+ return ret;
+}
+EXPORT_SYMBOL(ib_destroy_srq);
+
/* Queue pairs */
struct ib_qp *ib_create_qp(struct ib_pd *pd,
diff --git a/drivers/infiniband/hw/mthca/Makefile b/drivers/infiniband/hw/mthca/Makefile
index 5dcbd43..c44f7ba 100644
--- a/drivers/infiniband/hw/mthca/Makefile
+++ b/drivers/infiniband/hw/mthca/Makefile
@@ -1,5 +1,3 @@
-EXTRA_CFLAGS += -Idrivers/infiniband/include
-
ifdef CONFIG_INFINIBAND_MTHCA_DEBUG
EXTRA_CFLAGS += -DDEBUG
endif
@@ -9,4 +7,4 @@
ib_mthca-y := mthca_main.o mthca_cmd.o mthca_profile.o mthca_reset.o \
mthca_allocator.o mthca_eq.o mthca_pd.o mthca_cq.o \
mthca_mr.o mthca_qp.o mthca_av.o mthca_mcg.o mthca_mad.o \
- mthca_provider.o mthca_memfree.o mthca_uar.o
+ mthca_provider.o mthca_memfree.o mthca_uar.o mthca_srq.o
diff --git a/drivers/infiniband/hw/mthca/mthca_allocator.c b/drivers/infiniband/hw/mthca/mthca_allocator.c
index b1db48d..9ba3211 100644
--- a/drivers/infiniband/hw/mthca/mthca_allocator.c
+++ b/drivers/infiniband/hw/mthca/mthca_allocator.c
@@ -177,3 +177,119 @@
kfree(array->page_list);
}
+
+/*
+ * Handling for queue buffers -- we allocate a bunch of memory and
+ * register it in a memory region at HCA virtual address 0. If the
+ * requested size is > max_direct, we split the allocation into
+ * multiple pages, so we don't require too much contiguous memory.
+ */
+
+int mthca_buf_alloc(struct mthca_dev *dev, int size, int max_direct,
+ union mthca_buf *buf, int *is_direct, struct mthca_pd *pd,
+ int hca_write, struct mthca_mr *mr)
+{
+ int err = -ENOMEM;
+ int npages, shift;
+ u64 *dma_list = NULL;
+ dma_addr_t t;
+ int i;
+
+ if (size <= max_direct) {
+ *is_direct = 1;
+ npages = 1;
+ shift = get_order(size) + PAGE_SHIFT;
+
+ buf->direct.buf = dma_alloc_coherent(&dev->pdev->dev,
+ size, &t, GFP_KERNEL);
+ if (!buf->direct.buf)
+ return -ENOMEM;
+
+ pci_unmap_addr_set(&buf->direct, mapping, t);
+
+ memset(buf->direct.buf, 0, size);
+
+ while (t & ((1 << shift) - 1)) {
+ --shift;
+ npages *= 2;
+ }
+
+ dma_list = kmalloc(npages * sizeof *dma_list, GFP_KERNEL);
+ if (!dma_list)
+ goto err_free;
+
+ for (i = 0; i < npages; ++i)
+ dma_list[i] = t + i * (1 << shift);
+ } else {
+ *is_direct = 0;
+ npages = (size + PAGE_SIZE - 1) / PAGE_SIZE;
+ shift = PAGE_SHIFT;
+
+ dma_list = kmalloc(npages * sizeof *dma_list, GFP_KERNEL);
+ if (!dma_list)
+ return -ENOMEM;
+
+ buf->page_list = kmalloc(npages * sizeof *buf->page_list,
+ GFP_KERNEL);
+ if (!buf->page_list)
+ goto err_out;
+
+ for (i = 0; i < npages; ++i)
+ buf->page_list[i].buf = NULL;
+
+ for (i = 0; i < npages; ++i) {
+ buf->page_list[i].buf =
+ dma_alloc_coherent(&dev->pdev->dev, PAGE_SIZE,
+ &t, GFP_KERNEL);
+ if (!buf->page_list[i].buf)
+ goto err_free;
+
+ dma_list[i] = t;
+ pci_unmap_addr_set(&buf->page_list[i], mapping, t);
+
+ memset(buf->page_list[i].buf, 0, PAGE_SIZE);
+ }
+ }
+
+ err = mthca_mr_alloc_phys(dev, pd->pd_num,
+ dma_list, shift, npages,
+ 0, size,
+ MTHCA_MPT_FLAG_LOCAL_READ |
+ (hca_write ? MTHCA_MPT_FLAG_LOCAL_WRITE : 0),
+ mr);
+ if (err)
+ goto err_free;
+
+ kfree(dma_list);
+
+ return 0;
+
+err_free:
+ mthca_buf_free(dev, size, buf, *is_direct, NULL);
+
+err_out:
+ kfree(dma_list);
+
+ return err;
+}
+
+void mthca_buf_free(struct mthca_dev *dev, int size, union mthca_buf *buf,
+ int is_direct, struct mthca_mr *mr)
+{
+ int i;
+
+ if (mr)
+ mthca_free_mr(dev, mr);
+
+ if (is_direct)
+ dma_free_coherent(&dev->pdev->dev, size, buf->direct.buf,
+ pci_unmap_addr(&buf->direct, mapping));
+ else {
+ for (i = 0; i < (size + PAGE_SIZE - 1) / PAGE_SIZE; ++i)
+ dma_free_coherent(&dev->pdev->dev, PAGE_SIZE,
+ buf->page_list[i].buf,
+ pci_unmap_addr(&buf->page_list[i],
+ mapping));
+ kfree(buf->page_list);
+ }
+}
diff --git a/drivers/infiniband/hw/mthca/mthca_av.c b/drivers/infiniband/hw/mthca/mthca_av.c
index d58dcbe..889e850 100644
--- a/drivers/infiniband/hw/mthca/mthca_av.c
+++ b/drivers/infiniband/hw/mthca/mthca_av.c
@@ -35,22 +35,22 @@
#include <linux/init.h>
-#include <ib_verbs.h>
-#include <ib_cache.h>
+#include <rdma/ib_verbs.h>
+#include <rdma/ib_cache.h>
#include "mthca_dev.h"
struct mthca_av {
- u32 port_pd;
- u8 reserved1;
- u8 g_slid;
- u16 dlid;
- u8 reserved2;
- u8 gid_index;
- u8 msg_sr;
- u8 hop_limit;
- u32 sl_tclass_flowlabel;
- u32 dgid[4];
+ __be32 port_pd;
+ u8 reserved1;
+ u8 g_slid;
+ __be16 dlid;
+ u8 reserved2;
+ u8 gid_index;
+ u8 msg_sr;
+ u8 hop_limit;
+ __be32 sl_tclass_flowlabel;
+ __be32 dgid[4];
};
int mthca_create_ah(struct mthca_dev *dev,
@@ -128,7 +128,7 @@
av, (unsigned long) ah->avdma);
for (j = 0; j < 8; ++j)
printk(KERN_DEBUG " [%2x] %08x\n",
- j * 4, be32_to_cpu(((u32 *) av)[j]));
+ j * 4, be32_to_cpu(((__be32 *) av)[j]));
}
if (ah->type == MTHCA_AH_ON_HCA) {
@@ -169,7 +169,7 @@
header->lrh.service_level = be32_to_cpu(ah->av->sl_tclass_flowlabel) >> 28;
header->lrh.destination_lid = ah->av->dlid;
- header->lrh.source_lid = ah->av->g_slid & 0x7f;
+ header->lrh.source_lid = cpu_to_be16(ah->av->g_slid & 0x7f);
if (ah->av->g_slid & 0x80) {
header->grh_present = 1;
header->grh.traffic_class =
diff --git a/drivers/infiniband/hw/mthca/mthca_cmd.c b/drivers/infiniband/hw/mthca/mthca_cmd.c
index 1557a52..cc758a2 100644
--- a/drivers/infiniband/hw/mthca/mthca_cmd.c
+++ b/drivers/infiniband/hw/mthca/mthca_cmd.c
@@ -1,5 +1,6 @@
/*
* Copyright (c) 2004, 2005 Topspin Communications. All rights reserved.
+ * Copyright (c) 2005 Mellanox Technologies. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
@@ -36,7 +37,7 @@
#include <linux/pci.h>
#include <linux/errno.h>
#include <asm/io.h>
-#include <ib_mad.h>
+#include <rdma/ib_mad.h>
#include "mthca_dev.h"
#include "mthca_config_reg.h"
@@ -108,6 +109,7 @@
CMD_SW2HW_SRQ = 0x35,
CMD_HW2SW_SRQ = 0x36,
CMD_QUERY_SRQ = 0x37,
+ CMD_ARM_SRQ = 0x40,
/* QP/EE commands */
CMD_RST2INIT_QPEE = 0x19,
@@ -219,20 +221,20 @@
* (and some architectures such as ia64 implement memcpy_toio
* in terms of writeb).
*/
- __raw_writel(cpu_to_be32(in_param >> 32), dev->hcr + 0 * 4);
- __raw_writel(cpu_to_be32(in_param & 0xfffffffful), dev->hcr + 1 * 4);
- __raw_writel(cpu_to_be32(in_modifier), dev->hcr + 2 * 4);
- __raw_writel(cpu_to_be32(out_param >> 32), dev->hcr + 3 * 4);
- __raw_writel(cpu_to_be32(out_param & 0xfffffffful), dev->hcr + 4 * 4);
- __raw_writel(cpu_to_be32(token << 16), dev->hcr + 5 * 4);
+ __raw_writel((__force u32) cpu_to_be32(in_param >> 32), dev->hcr + 0 * 4);
+ __raw_writel((__force u32) cpu_to_be32(in_param & 0xfffffffful), dev->hcr + 1 * 4);
+ __raw_writel((__force u32) cpu_to_be32(in_modifier), dev->hcr + 2 * 4);
+ __raw_writel((__force u32) cpu_to_be32(out_param >> 32), dev->hcr + 3 * 4);
+ __raw_writel((__force u32) cpu_to_be32(out_param & 0xfffffffful), dev->hcr + 4 * 4);
+ __raw_writel((__force u32) cpu_to_be32(token << 16), dev->hcr + 5 * 4);
/* __raw_writel may not order writes. */
wmb();
- __raw_writel(cpu_to_be32((1 << HCR_GO_BIT) |
- (event ? (1 << HCA_E_BIT) : 0) |
- (op_modifier << HCR_OPMOD_SHIFT) |
- op), dev->hcr + 6 * 4);
+ __raw_writel((__force u32) cpu_to_be32((1 << HCR_GO_BIT) |
+ (event ? (1 << HCA_E_BIT) : 0) |
+ (op_modifier << HCR_OPMOD_SHIFT) |
+ op), dev->hcr + 6 * 4);
out:
up(&dev->cmd.hcr_sem);
@@ -273,12 +275,14 @@
goto out;
}
- if (out_is_imm) {
- memcpy_fromio(out_param, dev->hcr + HCR_OUT_PARAM_OFFSET, sizeof (u64));
- be64_to_cpus(out_param);
- }
+ if (out_is_imm)
+ *out_param =
+ (u64) be32_to_cpu((__force __be32)
+ __raw_readl(dev->hcr + HCR_OUT_PARAM_OFFSET)) << 32 |
+ (u64) be32_to_cpu((__force __be32)
+ __raw_readl(dev->hcr + HCR_OUT_PARAM_OFFSET + 4));
- *status = be32_to_cpu(__raw_readl(dev->hcr + HCR_STATUS_OFFSET)) >> 24;
+ *status = be32_to_cpu((__force __be32) __raw_readl(dev->hcr + HCR_STATUS_OFFSET)) >> 24;
out:
up(&dev->cmd.poll_sem);
@@ -1029,6 +1033,8 @@
mthca_dbg(dev, "Max QPs: %d, reserved QPs: %d, entry size: %d\n",
dev_lim->max_qps, dev_lim->reserved_qps, dev_lim->qpc_entry_sz);
+ mthca_dbg(dev, "Max SRQs: %d, reserved SRQs: %d, entry size: %d\n",
+ dev_lim->max_srqs, dev_lim->reserved_srqs, dev_lim->srq_entry_sz);
mthca_dbg(dev, "Max CQs: %d, reserved CQs: %d, entry size: %d\n",
dev_lim->max_cqs, dev_lim->reserved_cqs, dev_lim->cqc_entry_sz);
mthca_dbg(dev, "Max EQs: %d, reserved EQs: %d, entry size: %d\n",
@@ -1082,6 +1088,34 @@
return err;
}
+static void get_board_id(void *vsd, char *board_id)
+{
+ int i;
+
+#define VSD_OFFSET_SIG1 0x00
+#define VSD_OFFSET_SIG2 0xde
+#define VSD_OFFSET_MLX_BOARD_ID 0xd0
+#define VSD_OFFSET_TS_BOARD_ID 0x20
+
+#define VSD_SIGNATURE_TOPSPIN 0x5ad
+
+ memset(board_id, 0, MTHCA_BOARD_ID_LEN);
+
+ if (be16_to_cpup(vsd + VSD_OFFSET_SIG1) == VSD_SIGNATURE_TOPSPIN &&
+ be16_to_cpup(vsd + VSD_OFFSET_SIG2) == VSD_SIGNATURE_TOPSPIN) {
+ strlcpy(board_id, vsd + VSD_OFFSET_TS_BOARD_ID, MTHCA_BOARD_ID_LEN);
+ } else {
+ /*
+ * The board ID is a string but the firmware byte
+ * swaps each 4-byte word before passing it back to
+ * us. Therefore we need to swab it before printing.
+ */
+ for (i = 0; i < 4; ++i)
+ ((u32 *) board_id)[i] =
+ swab32(*(u32 *) (vsd + VSD_OFFSET_MLX_BOARD_ID + i * 4));
+ }
+}
+
int mthca_QUERY_ADAPTER(struct mthca_dev *dev,
struct mthca_adapter *adapter, u8 *status)
{
@@ -1094,6 +1128,7 @@
#define QUERY_ADAPTER_DEVICE_ID_OFFSET 0x04
#define QUERY_ADAPTER_REVISION_ID_OFFSET 0x08
#define QUERY_ADAPTER_INTA_PIN_OFFSET 0x10
+#define QUERY_ADAPTER_VSD_OFFSET 0x20
mailbox = mthca_alloc_mailbox(dev, GFP_KERNEL);
if (IS_ERR(mailbox))
@@ -1111,6 +1146,9 @@
MTHCA_GET(adapter->revision_id, outbox, QUERY_ADAPTER_REVISION_ID_OFFSET);
MTHCA_GET(adapter->inta_pin, outbox, QUERY_ADAPTER_INTA_PIN_OFFSET);
+ get_board_id(outbox + QUERY_ADAPTER_VSD_OFFSET / 4,
+ adapter->board_id);
+
out:
mthca_free_mailbox(dev, mailbox);
return err;
@@ -1121,7 +1159,7 @@
u8 *status)
{
struct mthca_mailbox *mailbox;
- u32 *inbox;
+ __be32 *inbox;
int err;
#define INIT_HCA_IN_SIZE 0x200
@@ -1247,10 +1285,8 @@
#define INIT_IB_FLAG_SIG (1 << 18)
#define INIT_IB_FLAG_NG (1 << 17)
#define INIT_IB_FLAG_G0 (1 << 16)
-#define INIT_IB_FLAG_1X (1 << 8)
-#define INIT_IB_FLAG_4X (1 << 9)
-#define INIT_IB_FLAG_12X (1 << 11)
#define INIT_IB_VL_SHIFT 4
+#define INIT_IB_PORT_WIDTH_SHIFT 8
#define INIT_IB_MTU_SHIFT 12
#define INIT_IB_MAX_GID_OFFSET 0x06
#define INIT_IB_MAX_PKEY_OFFSET 0x0a
@@ -1266,12 +1302,11 @@
memset(inbox, 0, INIT_IB_IN_SIZE);
flags = 0;
- flags |= param->enable_1x ? INIT_IB_FLAG_1X : 0;
- flags |= param->enable_4x ? INIT_IB_FLAG_4X : 0;
flags |= param->set_guid0 ? INIT_IB_FLAG_G0 : 0;
flags |= param->set_node_guid ? INIT_IB_FLAG_NG : 0;
flags |= param->set_si_guid ? INIT_IB_FLAG_SIG : 0;
flags |= param->vl_cap << INIT_IB_VL_SHIFT;
+ flags |= param->port_width << INIT_IB_PORT_WIDTH_SHIFT;
flags |= param->mtu_cap << INIT_IB_MTU_SHIFT;
MTHCA_PUT(inbox, flags, INIT_IB_FLAGS_OFFSET);
@@ -1342,7 +1377,7 @@
int mthca_MAP_ICM_page(struct mthca_dev *dev, u64 dma_addr, u64 virt, u8 *status)
{
struct mthca_mailbox *mailbox;
- u64 *inbox;
+ __be64 *inbox;
int err;
mailbox = mthca_alloc_mailbox(dev, GFP_KERNEL);
@@ -1468,6 +1503,27 @@
CMD_TIME_CLASS_A, status);
}
+int mthca_SW2HW_SRQ(struct mthca_dev *dev, struct mthca_mailbox *mailbox,
+ int srq_num, u8 *status)
+{
+ return mthca_cmd(dev, mailbox->dma, srq_num, 0, CMD_SW2HW_SRQ,
+ CMD_TIME_CLASS_A, status);
+}
+
+int mthca_HW2SW_SRQ(struct mthca_dev *dev, struct mthca_mailbox *mailbox,
+ int srq_num, u8 *status)
+{
+ return mthca_cmd_box(dev, 0, mailbox->dma, srq_num, 0,
+ CMD_HW2SW_SRQ,
+ CMD_TIME_CLASS_A, status);
+}
+
+int mthca_ARM_SRQ(struct mthca_dev *dev, int srq_num, int limit, u8 *status)
+{
+ return mthca_cmd(dev, limit, srq_num, 0, CMD_ARM_SRQ,
+ CMD_TIME_CLASS_B, status);
+}
+
int mthca_MODIFY_QP(struct mthca_dev *dev, int trans, u32 num,
int is_ee, struct mthca_mailbox *mailbox, u32 optmask,
u8 *status)
@@ -1513,7 +1569,7 @@
if (i % 8 == 0)
printk(" [%02x] ", i * 4);
printk(" %08x",
- be32_to_cpu(((u32 *) mailbox->buf)[i + 2]));
+ be32_to_cpu(((__be32 *) mailbox->buf)[i + 2]));
if ((i + 1) % 8 == 0)
printk("\n");
}
@@ -1533,7 +1589,7 @@
if (i % 8 == 0)
printk("[%02x] ", i * 4);
printk(" %08x",
- be32_to_cpu(((u32 *) mailbox->buf)[i + 2]));
+ be32_to_cpu(((__be32 *) mailbox->buf)[i + 2]));
if ((i + 1) % 8 == 0)
printk("\n");
}
diff --git a/drivers/infiniband/hw/mthca/mthca_cmd.h b/drivers/infiniband/hw/mthca/mthca_cmd.h
index ed517f1..65f976a 100644
--- a/drivers/infiniband/hw/mthca/mthca_cmd.h
+++ b/drivers/infiniband/hw/mthca/mthca_cmd.h
@@ -1,5 +1,6 @@
/*
* Copyright (c) 2004, 2005 Topspin Communications. All rights reserved.
+ * Copyright (c) 2005 Mellanox Technologies. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
@@ -35,7 +36,7 @@
#ifndef MTHCA_CMD_H
#define MTHCA_CMD_H
-#include <ib_verbs.h>
+#include <rdma/ib_verbs.h>
#define MTHCA_MAILBOX_SIZE 4096
@@ -183,10 +184,11 @@
};
struct mthca_adapter {
- u32 vendor_id;
- u32 device_id;
- u32 revision_id;
- u8 inta_pin;
+ u32 vendor_id;
+ u32 device_id;
+ u32 revision_id;
+ char board_id[MTHCA_BOARD_ID_LEN];
+ u8 inta_pin;
};
struct mthca_init_hca_param {
@@ -218,8 +220,7 @@
};
struct mthca_init_ib_param {
- int enable_1x;
- int enable_4x;
+ int port_width;
int vl_cap;
int mtu_cap;
u16 gid_cap;
@@ -297,6 +298,11 @@
int cq_num, u8 *status);
int mthca_HW2SW_CQ(struct mthca_dev *dev, struct mthca_mailbox *mailbox,
int cq_num, u8 *status);
+int mthca_SW2HW_SRQ(struct mthca_dev *dev, struct mthca_mailbox *mailbox,
+ int srq_num, u8 *status);
+int mthca_HW2SW_SRQ(struct mthca_dev *dev, struct mthca_mailbox *mailbox,
+ int srq_num, u8 *status);
+int mthca_ARM_SRQ(struct mthca_dev *dev, int srq_num, int limit, u8 *status);
int mthca_MODIFY_QP(struct mthca_dev *dev, int trans, u32 num,
int is_ee, struct mthca_mailbox *mailbox, u32 optmask,
u8 *status);
diff --git a/drivers/infiniband/hw/mthca/mthca_config_reg.h b/drivers/infiniband/hw/mthca/mthca_config_reg.h
index b4bfbbf..afa56bf 100644
--- a/drivers/infiniband/hw/mthca/mthca_config_reg.h
+++ b/drivers/infiniband/hw/mthca/mthca_config_reg.h
@@ -1,5 +1,6 @@
/*
* Copyright (c) 2004 Topspin Communications. All rights reserved.
+ * Copyright (c) 2005 Mellanox Technologies. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
diff --git a/drivers/infiniband/hw/mthca/mthca_cq.c b/drivers/infiniband/hw/mthca/mthca_cq.c
index 5687c30..8600b6c 100644
--- a/drivers/infiniband/hw/mthca/mthca_cq.c
+++ b/drivers/infiniband/hw/mthca/mthca_cq.c
@@ -2,6 +2,8 @@
* Copyright (c) 2004, 2005 Topspin Communications. All rights reserved.
* Copyright (c) 2005 Sun Microsystems, Inc. All rights reserved.
* Copyright (c) 2005 Cisco Systems, Inc. All rights reserved.
+ * Copyright (c) 2005 Mellanox Technologies. All rights reserved.
+ * Copyright (c) 2004 Voltaire, Inc. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
@@ -37,7 +39,7 @@
#include <linux/init.h>
#include <linux/hardirq.h>
-#include <ib_pack.h>
+#include <rdma/ib_pack.h>
#include "mthca_dev.h"
#include "mthca_cmd.h"
@@ -55,21 +57,21 @@
* Must be packed because start is 64 bits but only aligned to 32 bits.
*/
struct mthca_cq_context {
- u32 flags;
- u64 start;
- u32 logsize_usrpage;
- u32 error_eqn; /* Tavor only */
- u32 comp_eqn;
- u32 pd;
- u32 lkey;
- u32 last_notified_index;
- u32 solicit_producer_index;
- u32 consumer_index;
- u32 producer_index;
- u32 cqn;
- u32 ci_db; /* Arbel only */
- u32 state_db; /* Arbel only */
- u32 reserved;
+ __be32 flags;
+ __be64 start;
+ __be32 logsize_usrpage;
+ __be32 error_eqn; /* Tavor only */
+ __be32 comp_eqn;
+ __be32 pd;
+ __be32 lkey;
+ __be32 last_notified_index;
+ __be32 solicit_producer_index;
+ __be32 consumer_index;
+ __be32 producer_index;
+ __be32 cqn;
+ __be32 ci_db; /* Arbel only */
+ __be32 state_db; /* Arbel only */
+ u32 reserved;
} __attribute__((packed));
#define MTHCA_CQ_STATUS_OK ( 0 << 28)
@@ -108,31 +110,31 @@
};
struct mthca_cqe {
- u32 my_qpn;
- u32 my_ee;
- u32 rqpn;
- u16 sl_g_mlpath;
- u16 rlid;
- u32 imm_etype_pkey_eec;
- u32 byte_cnt;
- u32 wqe;
- u8 opcode;
- u8 is_send;
- u8 reserved;
- u8 owner;
+ __be32 my_qpn;
+ __be32 my_ee;
+ __be32 rqpn;
+ __be16 sl_g_mlpath;
+ __be16 rlid;
+ __be32 imm_etype_pkey_eec;
+ __be32 byte_cnt;
+ __be32 wqe;
+ u8 opcode;
+ u8 is_send;
+ u8 reserved;
+ u8 owner;
};
struct mthca_err_cqe {
- u32 my_qpn;
- u32 reserved1[3];
- u8 syndrome;
- u8 reserved2;
- u16 db_cnt;
- u32 reserved3;
- u32 wqe;
- u8 opcode;
- u8 reserved4[2];
- u8 owner;
+ __be32 my_qpn;
+ u32 reserved1[3];
+ u8 syndrome;
+ u8 reserved2;
+ __be16 db_cnt;
+ u32 reserved3;
+ __be32 wqe;
+ u8 opcode;
+ u8 reserved4[2];
+ u8 owner;
};
#define MTHCA_CQ_ENTRY_OWNER_SW (0 << 7)
@@ -191,7 +193,7 @@
static inline void update_cons_index(struct mthca_dev *dev, struct mthca_cq *cq,
int incr)
{
- u32 doorbell[2];
+ __be32 doorbell[2];
if (mthca_is_memfree(dev)) {
*cq->set_ci_db = cpu_to_be32(cq->cons_index);
@@ -222,7 +224,8 @@
cq->ibcq.comp_handler(&cq->ibcq, cq->ibcq.cq_context);
}
-void mthca_cq_clean(struct mthca_dev *dev, u32 cqn, u32 qpn)
+void mthca_cq_clean(struct mthca_dev *dev, u32 cqn, u32 qpn,
+ struct mthca_srq *srq)
{
struct mthca_cq *cq;
struct mthca_cqe *cqe;
@@ -263,8 +266,11 @@
*/
while (prod_index > cq->cons_index) {
cqe = get_cqe(cq, (prod_index - 1) & cq->ibcq.cqe);
- if (cqe->my_qpn == cpu_to_be32(qpn))
+ if (cqe->my_qpn == cpu_to_be32(qpn)) {
+ if (srq)
+ mthca_free_srq_wqe(srq, be32_to_cpu(cqe->wqe));
++nfreed;
+ }
else if (nfreed)
memcpy(get_cqe(cq, (prod_index - 1 + nfreed) &
cq->ibcq.cqe),
@@ -291,7 +297,7 @@
{
int err;
int dbd;
- u32 new_wqe;
+ __be32 new_wqe;
if (cqe->syndrome == SYNDROME_LOCAL_QP_OP_ERR) {
mthca_dbg(dev, "local QP operation err "
@@ -365,6 +371,13 @@
break;
}
+ /*
+ * Mem-free HCAs always generate one CQE per WQE, even in the
+ * error case, so we don't have to check the doorbell count, etc.
+ */
+ if (mthca_is_memfree(dev))
+ return 0;
+
err = mthca_free_err_wqe(dev, qp, is_send, wqe_index, &dbd, &new_wqe);
if (err)
return err;
@@ -373,12 +386,8 @@
* If we're at the end of the WQE chain, or we've used up our
* doorbell count, free the CQE. Otherwise just update it for
* the next poll operation.
- *
- * This does not apply to mem-free HCAs: they don't use the
- * doorbell count field, and so we should always free the CQE.
*/
- if (mthca_is_memfree(dev) ||
- !(new_wqe & cpu_to_be32(0x3f)) || (!cqe->db_cnt && dbd))
+ if (!(new_wqe & cpu_to_be32(0x3f)) || (!cqe->db_cnt && dbd))
return 0;
cqe->db_cnt = cpu_to_be16(be16_to_cpu(cqe->db_cnt) - dbd);
@@ -450,23 +459,27 @@
>> wq->wqe_shift);
entry->wr_id = (*cur_qp)->wrid[wqe_index +
(*cur_qp)->rq.max];
+ } else if ((*cur_qp)->ibqp.srq) {
+ struct mthca_srq *srq = to_msrq((*cur_qp)->ibqp.srq);
+ u32 wqe = be32_to_cpu(cqe->wqe);
+ wq = NULL;
+ wqe_index = wqe >> srq->wqe_shift;
+ entry->wr_id = srq->wrid[wqe_index];
+ mthca_free_srq_wqe(srq, wqe);
} else {
wq = &(*cur_qp)->rq;
wqe_index = be32_to_cpu(cqe->wqe) >> wq->wqe_shift;
entry->wr_id = (*cur_qp)->wrid[wqe_index];
}
- if (wq->last_comp < wqe_index)
- wq->tail += wqe_index - wq->last_comp;
- else
- wq->tail += wqe_index + wq->max - wq->last_comp;
+ if (wq) {
+ if (wq->last_comp < wqe_index)
+ wq->tail += wqe_index - wq->last_comp;
+ else
+ wq->tail += wqe_index + wq->max - wq->last_comp;
- wq->last_comp = wqe_index;
-
- if (0)
- mthca_dbg(dev, "%s completion for QP %06x, index %d (nr %d)\n",
- is_send ? "Send" : "Receive",
- (*cur_qp)->qpn, wqe_index, wq->max);
+ wq->last_comp = wqe_index;
+ }
if (is_error) {
err = handle_error_cqe(dev, cq, *cur_qp, wqe_index, is_send,
@@ -584,13 +597,13 @@
int mthca_tavor_arm_cq(struct ib_cq *cq, enum ib_cq_notify notify)
{
- u32 doorbell[2];
+ __be32 doorbell[2];
doorbell[0] = cpu_to_be32((notify == IB_CQ_SOLICITED ?
MTHCA_TAVOR_CQ_DB_REQ_NOT_SOL :
MTHCA_TAVOR_CQ_DB_REQ_NOT) |
to_mcq(cq)->cqn);
- doorbell[1] = 0xffffffff;
+ doorbell[1] = (__force __be32) 0xffffffff;
mthca_write64(doorbell,
to_mdev(cq->device)->kar + MTHCA_CQ_DOORBELL,
@@ -602,9 +615,9 @@
int mthca_arbel_arm_cq(struct ib_cq *ibcq, enum ib_cq_notify notify)
{
struct mthca_cq *cq = to_mcq(ibcq);
- u32 doorbell[2];
+ __be32 doorbell[2];
u32 sn;
- u32 ci;
+ __be32 ci;
sn = cq->arm_sn & 3;
ci = cpu_to_be32(cq->cons_index);
@@ -637,113 +650,8 @@
static void mthca_free_cq_buf(struct mthca_dev *dev, struct mthca_cq *cq)
{
- int i;
- int size;
-
- if (cq->is_direct)
- dma_free_coherent(&dev->pdev->dev,
- (cq->ibcq.cqe + 1) * MTHCA_CQ_ENTRY_SIZE,
- cq->queue.direct.buf,
- pci_unmap_addr(&cq->queue.direct,
- mapping));
- else {
- size = (cq->ibcq.cqe + 1) * MTHCA_CQ_ENTRY_SIZE;
- for (i = 0; i < (size + PAGE_SIZE - 1) / PAGE_SIZE; ++i)
- if (cq->queue.page_list[i].buf)
- dma_free_coherent(&dev->pdev->dev, PAGE_SIZE,
- cq->queue.page_list[i].buf,
- pci_unmap_addr(&cq->queue.page_list[i],
- mapping));
-
- kfree(cq->queue.page_list);
- }
-}
-
-static int mthca_alloc_cq_buf(struct mthca_dev *dev, int size,
- struct mthca_cq *cq)
-{
- int err = -ENOMEM;
- int npages, shift;
- u64 *dma_list = NULL;
- dma_addr_t t;
- int i;
-
- if (size <= MTHCA_MAX_DIRECT_CQ_SIZE) {
- cq->is_direct = 1;
- npages = 1;
- shift = get_order(size) + PAGE_SHIFT;
-
- cq->queue.direct.buf = dma_alloc_coherent(&dev->pdev->dev,
- size, &t, GFP_KERNEL);
- if (!cq->queue.direct.buf)
- return -ENOMEM;
-
- pci_unmap_addr_set(&cq->queue.direct, mapping, t);
-
- memset(cq->queue.direct.buf, 0, size);
-
- while (t & ((1 << shift) - 1)) {
- --shift;
- npages *= 2;
- }
-
- dma_list = kmalloc(npages * sizeof *dma_list, GFP_KERNEL);
- if (!dma_list)
- goto err_free;
-
- for (i = 0; i < npages; ++i)
- dma_list[i] = t + i * (1 << shift);
- } else {
- cq->is_direct = 0;
- npages = (size + PAGE_SIZE - 1) / PAGE_SIZE;
- shift = PAGE_SHIFT;
-
- dma_list = kmalloc(npages * sizeof *dma_list, GFP_KERNEL);
- if (!dma_list)
- return -ENOMEM;
-
- cq->queue.page_list = kmalloc(npages * sizeof *cq->queue.page_list,
- GFP_KERNEL);
- if (!cq->queue.page_list)
- goto err_out;
-
- for (i = 0; i < npages; ++i)
- cq->queue.page_list[i].buf = NULL;
-
- for (i = 0; i < npages; ++i) {
- cq->queue.page_list[i].buf =
- dma_alloc_coherent(&dev->pdev->dev, PAGE_SIZE,
- &t, GFP_KERNEL);
- if (!cq->queue.page_list[i].buf)
- goto err_free;
-
- dma_list[i] = t;
- pci_unmap_addr_set(&cq->queue.page_list[i], mapping, t);
-
- memset(cq->queue.page_list[i].buf, 0, PAGE_SIZE);
- }
- }
-
- err = mthca_mr_alloc_phys(dev, dev->driver_pd.pd_num,
- dma_list, shift, npages,
- 0, size,
- MTHCA_MPT_FLAG_LOCAL_WRITE |
- MTHCA_MPT_FLAG_LOCAL_READ,
- &cq->mr);
- if (err)
- goto err_free;
-
- kfree(dma_list);
-
- return 0;
-
-err_free:
- mthca_free_cq_buf(dev, cq);
-
-err_out:
- kfree(dma_list);
-
- return err;
+ mthca_buf_free(dev, (cq->ibcq.cqe + 1) * MTHCA_CQ_ENTRY_SIZE,
+ &cq->queue, cq->is_direct, &cq->mr);
}
int mthca_init_cq(struct mthca_dev *dev, int nent,
@@ -795,7 +703,9 @@
cq_context = mailbox->buf;
if (cq->is_kernel) {
- err = mthca_alloc_cq_buf(dev, size, cq);
+ err = mthca_buf_alloc(dev, size, MTHCA_MAX_DIRECT_CQ_SIZE,
+ &cq->queue, &cq->is_direct,
+ &dev->driver_pd, 1, &cq->mr);
if (err)
goto err_out_mailbox;
@@ -811,7 +721,6 @@
cq_context->flags = cpu_to_be32(MTHCA_CQ_STATUS_OK |
MTHCA_CQ_STATE_DISARMED |
MTHCA_CQ_FLAG_TR);
- cq_context->start = cpu_to_be64(0);
cq_context->logsize_usrpage = cpu_to_be32((ffs(nent) - 1) << 24);
if (ctx)
cq_context->logsize_usrpage |= cpu_to_be32(ctx->uar.index);
@@ -857,10 +766,8 @@
return 0;
err_out_free_mr:
- if (cq->is_kernel) {
- mthca_free_mr(dev, &cq->mr);
+ if (cq->is_kernel)
mthca_free_cq_buf(dev, cq);
- }
err_out_mailbox:
mthca_free_mailbox(dev, mailbox);
@@ -904,7 +811,7 @@
mthca_warn(dev, "HW2SW_CQ returned status 0x%02x\n", status);
if (0) {
- u32 *ctx = mailbox->buf;
+ __be32 *ctx = mailbox->buf;
int j;
printk(KERN_ERR "context for CQN %x (cons index %x, next sw %d)\n",
@@ -928,7 +835,6 @@
wait_event(cq->wait, !atomic_read(&cq->refcount));
if (cq->is_kernel) {
- mthca_free_mr(dev, &cq->mr);
mthca_free_cq_buf(dev, cq);
if (mthca_is_memfree(dev)) {
mthca_free_db(dev, MTHCA_DB_TYPE_CQ_ARM, cq->arm_db_index);
diff --git a/drivers/infiniband/hw/mthca/mthca_dev.h b/drivers/infiniband/hw/mthca/mthca_dev.h
index 5ecdd2e..7bff5a8 100644
--- a/drivers/infiniband/hw/mthca/mthca_dev.h
+++ b/drivers/infiniband/hw/mthca/mthca_dev.h
@@ -2,6 +2,8 @@
* Copyright (c) 2004, 2005 Topspin Communications. All rights reserved.
* Copyright (c) 2005 Sun Microsystems, Inc. All rights reserved.
* Copyright (c) 2005 Cisco Systems. All rights reserved.
+ * Copyright (c) 2005 Mellanox Technologies. All rights reserved.
+ * Copyright (c) 2004 Voltaire, Inc. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
@@ -67,6 +69,10 @@
};
enum {
+ MTHCA_BOARD_ID_LEN = 64
+};
+
+enum {
MTHCA_EQ_CONTEXT_SIZE = 0x40,
MTHCA_CQ_CONTEXT_SIZE = 0x40,
MTHCA_QP_CONTEXT_SIZE = 0x200,
@@ -142,6 +148,7 @@
int reserved_mcgs;
int num_pds;
int reserved_pds;
+ u8 port_width_cap;
};
struct mthca_alloc {
@@ -211,6 +218,13 @@
struct mthca_icm_table *table;
};
+struct mthca_srq_table {
+ struct mthca_alloc alloc;
+ spinlock_t lock;
+ struct mthca_array srq;
+ struct mthca_icm_table *table;
+};
+
struct mthca_qp_table {
struct mthca_alloc alloc;
u32 rdb_base;
@@ -246,6 +260,7 @@
unsigned long device_cap_flags;
u32 rev_id;
+ char board_id[MTHCA_BOARD_ID_LEN];
/* firmware info */
u64 fw_ver;
@@ -291,6 +306,7 @@
struct mthca_mr_table mr_table;
struct mthca_eq_table eq_table;
struct mthca_cq_table cq_table;
+ struct mthca_srq_table srq_table;
struct mthca_qp_table qp_table;
struct mthca_av_table av_table;
struct mthca_mcg_table mcg_table;
@@ -331,14 +347,13 @@
#define MTHCA_PUT(dest, source, offset) \
do { \
- __typeof__(source) *__p = \
- (__typeof__(source) *) ((char *) (dest) + (offset)); \
+ void *__d = ((char *) (dest) + (offset)); \
switch (sizeof(source)) { \
- case 1: *__p = (source); break; \
- case 2: *__p = cpu_to_be16(source); break; \
- case 4: *__p = cpu_to_be32(source); break; \
- case 8: *__p = cpu_to_be64(source); break; \
- default: __buggy_use_of_MTHCA_PUT(); \
+ case 1: *(u8 *) __d = (source); break; \
+ case 2: *(__be16 *) __d = cpu_to_be16(source); break; \
+ case 4: *(__be32 *) __d = cpu_to_be32(source); break; \
+ case 8: *(__be64 *) __d = cpu_to_be64(source); break; \
+ default: __buggy_use_of_MTHCA_PUT(); \
} \
} while (0)
@@ -354,12 +369,18 @@
void mthca_array_clear(struct mthca_array *array, int index);
int mthca_array_init(struct mthca_array *array, int nent);
void mthca_array_cleanup(struct mthca_array *array, int nent);
+int mthca_buf_alloc(struct mthca_dev *dev, int size, int max_direct,
+ union mthca_buf *buf, int *is_direct, struct mthca_pd *pd,
+ int hca_write, struct mthca_mr *mr);
+void mthca_buf_free(struct mthca_dev *dev, int size, union mthca_buf *buf,
+ int is_direct, struct mthca_mr *mr);
int mthca_init_uar_table(struct mthca_dev *dev);
int mthca_init_pd_table(struct mthca_dev *dev);
int mthca_init_mr_table(struct mthca_dev *dev);
int mthca_init_eq_table(struct mthca_dev *dev);
int mthca_init_cq_table(struct mthca_dev *dev);
+int mthca_init_srq_table(struct mthca_dev *dev);
int mthca_init_qp_table(struct mthca_dev *dev);
int mthca_init_av_table(struct mthca_dev *dev);
int mthca_init_mcg_table(struct mthca_dev *dev);
@@ -369,6 +390,7 @@
void mthca_cleanup_mr_table(struct mthca_dev *dev);
void mthca_cleanup_eq_table(struct mthca_dev *dev);
void mthca_cleanup_cq_table(struct mthca_dev *dev);
+void mthca_cleanup_srq_table(struct mthca_dev *dev);
void mthca_cleanup_qp_table(struct mthca_dev *dev);
void mthca_cleanup_av_table(struct mthca_dev *dev);
void mthca_cleanup_mcg_table(struct mthca_dev *dev);
@@ -419,7 +441,19 @@
void mthca_free_cq(struct mthca_dev *dev,
struct mthca_cq *cq);
void mthca_cq_event(struct mthca_dev *dev, u32 cqn);
-void mthca_cq_clean(struct mthca_dev *dev, u32 cqn, u32 qpn);
+void mthca_cq_clean(struct mthca_dev *dev, u32 cqn, u32 qpn,
+ struct mthca_srq *srq);
+
+int mthca_alloc_srq(struct mthca_dev *dev, struct mthca_pd *pd,
+ struct ib_srq_attr *attr, struct mthca_srq *srq);
+void mthca_free_srq(struct mthca_dev *dev, struct mthca_srq *srq);
+void mthca_srq_event(struct mthca_dev *dev, u32 srqn,
+ enum ib_event_type event_type);
+void mthca_free_srq_wqe(struct mthca_srq *srq, u32 wqe_addr);
+int mthca_tavor_post_srq_recv(struct ib_srq *srq, struct ib_recv_wr *wr,
+ struct ib_recv_wr **bad_wr);
+int mthca_arbel_post_srq_recv(struct ib_srq *srq, struct ib_recv_wr *wr,
+ struct ib_recv_wr **bad_wr);
void mthca_qp_event(struct mthca_dev *dev, u32 qpn,
enum ib_event_type event_type);
@@ -433,7 +467,7 @@
int mthca_arbel_post_receive(struct ib_qp *ibqp, struct ib_recv_wr *wr,
struct ib_recv_wr **bad_wr);
int mthca_free_err_wqe(struct mthca_dev *dev, struct mthca_qp *qp, int is_send,
- int index, int *dbd, u32 *new_wqe);
+ int index, int *dbd, __be32 *new_wqe);
int mthca_alloc_qp(struct mthca_dev *dev,
struct mthca_pd *pd,
struct mthca_cq *send_cq,
diff --git a/drivers/infiniband/hw/mthca/mthca_doorbell.h b/drivers/infiniband/hw/mthca/mthca_doorbell.h
index 535fad7..dd9a44d 100644
--- a/drivers/infiniband/hw/mthca/mthca_doorbell.h
+++ b/drivers/infiniband/hw/mthca/mthca_doorbell.h
@@ -1,6 +1,7 @@
/*
* Copyright (c) 2004 Topspin Communications. All rights reserved.
* Copyright (c) 2005 Sun Microsystems, Inc. All rights reserved.
+ * Copyright (c) 2005 Mellanox Technologies. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
@@ -57,13 +58,13 @@
__raw_writeq((__force u64) val, dest);
}
-static inline void mthca_write64(u32 val[2], void __iomem *dest,
+static inline void mthca_write64(__be32 val[2], void __iomem *dest,
spinlock_t *doorbell_lock)
{
__raw_writeq(*(u64 *) val, dest);
}
-static inline void mthca_write_db_rec(u32 val[2], u32 *db)
+static inline void mthca_write_db_rec(__be32 val[2], __be32 *db)
{
*(u64 *) db = *(u64 *) val;
}
@@ -86,18 +87,18 @@
__raw_writel(((__force u32 *) &val)[1], dest + 4);
}
-static inline void mthca_write64(u32 val[2], void __iomem *dest,
+static inline void mthca_write64(__be32 val[2], void __iomem *dest,
spinlock_t *doorbell_lock)
{
unsigned long flags;
spin_lock_irqsave(doorbell_lock, flags);
- __raw_writel(val[0], dest);
- __raw_writel(val[1], dest + 4);
+ __raw_writel((__force u32) val[0], dest);
+ __raw_writel((__force u32) val[1], dest + 4);
spin_unlock_irqrestore(doorbell_lock, flags);
}
-static inline void mthca_write_db_rec(u32 val[2], u32 *db)
+static inline void mthca_write_db_rec(__be32 val[2], __be32 *db)
{
db[0] = val[0];
wmb();
diff --git a/drivers/infiniband/hw/mthca/mthca_eq.c b/drivers/infiniband/hw/mthca/mthca_eq.c
index cbcf2b4..18f0981 100644
--- a/drivers/infiniband/hw/mthca/mthca_eq.c
+++ b/drivers/infiniband/hw/mthca/mthca_eq.c
@@ -1,5 +1,6 @@
/*
* Copyright (c) 2004, 2005 Topspin Communications. All rights reserved.
+ * Copyright (c) 2005 Mellanox Technologies. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
@@ -51,18 +52,18 @@
* Must be packed because start is 64 bits but only aligned to 32 bits.
*/
struct mthca_eq_context {
- u32 flags;
- u64 start;
- u32 logsize_usrpage;
- u32 tavor_pd; /* reserved for Arbel */
- u8 reserved1[3];
- u8 intr;
- u32 arbel_pd; /* lost_count for Tavor */
- u32 lkey;
- u32 reserved2[2];
- u32 consumer_index;
- u32 producer_index;
- u32 reserved3[4];
+ __be32 flags;
+ __be64 start;
+ __be32 logsize_usrpage;
+ __be32 tavor_pd; /* reserved for Arbel */
+ u8 reserved1[3];
+ u8 intr;
+ __be32 arbel_pd; /* lost_count for Tavor */
+ __be32 lkey;
+ u32 reserved2[2];
+ __be32 consumer_index;
+ __be32 producer_index;
+ u32 reserved3[4];
} __attribute__((packed));
#define MTHCA_EQ_STATUS_OK ( 0 << 28)
@@ -127,28 +128,28 @@
union {
u32 raw[6];
struct {
- u32 cqn;
+ __be32 cqn;
} __attribute__((packed)) comp;
struct {
- u16 reserved1;
- u16 token;
- u32 reserved2;
- u8 reserved3[3];
- u8 status;
- u64 out_param;
+ u16 reserved1;
+ __be16 token;
+ u32 reserved2;
+ u8 reserved3[3];
+ u8 status;
+ __be64 out_param;
} __attribute__((packed)) cmd;
struct {
- u32 qpn;
+ __be32 qpn;
} __attribute__((packed)) qp;
struct {
- u32 cqn;
- u32 reserved1;
- u8 reserved2[3];
- u8 syndrome;
+ __be32 cqn;
+ u32 reserved1;
+ u8 reserved2[3];
+ u8 syndrome;
} __attribute__((packed)) cq_err;
struct {
- u32 reserved1[2];
- u32 port;
+ u32 reserved1[2];
+ __be32 port;
} __attribute__((packed)) port_change;
} event;
u8 reserved3[3];
@@ -167,7 +168,7 @@
static inline void tavor_set_eq_ci(struct mthca_dev *dev, struct mthca_eq *eq, u32 ci)
{
- u32 doorbell[2];
+ __be32 doorbell[2];
doorbell[0] = cpu_to_be32(MTHCA_EQ_DB_SET_CI | eq->eqn);
doorbell[1] = cpu_to_be32(ci & (eq->nent - 1));
@@ -190,8 +191,8 @@
{
/* See comment in tavor_set_eq_ci() above. */
wmb();
- __raw_writel(cpu_to_be32(ci), dev->eq_regs.arbel.eq_set_ci_base +
- eq->eqn * 8);
+ __raw_writel((__force u32) cpu_to_be32(ci),
+ dev->eq_regs.arbel.eq_set_ci_base + eq->eqn * 8);
/* We still want ordering, just not swabbing, so add a barrier */
mb();
}
@@ -206,7 +207,7 @@
static inline void tavor_eq_req_not(struct mthca_dev *dev, int eqn)
{
- u32 doorbell[2];
+ __be32 doorbell[2];
doorbell[0] = cpu_to_be32(MTHCA_EQ_DB_REQ_NOT | eqn);
doorbell[1] = 0;
@@ -224,7 +225,7 @@
static inline void disarm_cq(struct mthca_dev *dev, int eqn, int cqn)
{
if (!mthca_is_memfree(dev)) {
- u32 doorbell[2];
+ __be32 doorbell[2];
doorbell[0] = cpu_to_be32(MTHCA_EQ_DB_DISARM_CQ | eqn);
doorbell[1] = cpu_to_be32(cqn);
diff --git a/drivers/infiniband/hw/mthca/mthca_mad.c b/drivers/infiniband/hw/mthca/mthca_mad.c
index 7df2236..9804174 100644
--- a/drivers/infiniband/hw/mthca/mthca_mad.c
+++ b/drivers/infiniband/hw/mthca/mthca_mad.c
@@ -1,5 +1,7 @@
/*
* Copyright (c) 2004 Topspin Communications. All rights reserved.
+ * Copyright (c) 2005 Mellanox Technologies. All rights reserved.
+ * Copyright (c) 2004 Voltaire, Inc. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
@@ -32,9 +34,9 @@
* $Id: mthca_mad.c 1349 2004-12-16 21:09:43Z roland $
*/
-#include <ib_verbs.h>
-#include <ib_mad.h>
-#include <ib_smi.h>
+#include <rdma/ib_verbs.h>
+#include <rdma/ib_mad.h>
+#include <rdma/ib_smi.h>
#include "mthca_dev.h"
#include "mthca_cmd.h"
@@ -192,7 +194,7 @@
{
int err;
u8 status;
- u16 slid = in_wc ? in_wc->slid : IB_LID_PERMISSIVE;
+ u16 slid = in_wc ? in_wc->slid : be16_to_cpu(IB_LID_PERMISSIVE);
/* Forward locally generated traps to the SM */
if (in_mad->mad_hdr.method == IB_MGMT_METHOD_TRAP &&
diff --git a/drivers/infiniband/hw/mthca/mthca_main.c b/drivers/infiniband/hw/mthca/mthca_main.c
index 2ef9168..3241d6c 100644
--- a/drivers/infiniband/hw/mthca/mthca_main.c
+++ b/drivers/infiniband/hw/mthca/mthca_main.c
@@ -1,6 +1,7 @@
/*
* Copyright (c) 2004, 2005 Topspin Communications. All rights reserved.
* Copyright (c) 2005 Sun Microsystems, Inc. All rights reserved.
+ * Copyright (c) 2005 Mellanox Technologies. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
@@ -34,7 +35,6 @@
*/
#include <linux/config.h>
-#include <linux/version.h>
#include <linux/module.h>
#include <linux/init.h>
#include <linux/errno.h>
@@ -171,6 +171,7 @@
mdev->limits.reserved_mrws = dev_lim->reserved_mrws;
mdev->limits.reserved_uars = dev_lim->reserved_uars;
mdev->limits.reserved_pds = dev_lim->reserved_pds;
+ mdev->limits.port_width_cap = dev_lim->max_port_width;
/* IB_DEVICE_RESIZE_MAX_WR not supported by driver.
May be doable since hardware supports it for SRQ.
@@ -212,7 +213,6 @@
struct mthca_dev_lim dev_lim;
struct mthca_profile profile;
struct mthca_init_hca_param init_hca;
- struct mthca_adapter adapter;
err = mthca_SYS_EN(mdev, &status);
if (err) {
@@ -253,6 +253,8 @@
profile = default_profile;
profile.num_uar = dev_lim.uar_size / PAGE_SIZE;
profile.uarc_size = 0;
+ if (mdev->mthca_flags & MTHCA_FLAG_SRQ)
+ profile.num_srq = dev_lim.max_srqs;
err = mthca_make_profile(mdev, &profile, &dev_lim, &init_hca);
if (err < 0)
@@ -270,26 +272,8 @@
goto err_disable;
}
- err = mthca_QUERY_ADAPTER(mdev, &adapter, &status);
- if (err) {
- mthca_err(mdev, "QUERY_ADAPTER command failed, aborting.\n");
- goto err_close;
- }
- if (status) {
- mthca_err(mdev, "QUERY_ADAPTER returned status 0x%02x, "
- "aborting.\n", status);
- err = -EINVAL;
- goto err_close;
- }
-
- mdev->eq_table.inta_pin = adapter.inta_pin;
- mdev->rev_id = adapter.revision_id;
-
return 0;
-err_close:
- mthca_CLOSE_HCA(mdev, 0, &status);
-
err_disable:
mthca_SYS_DIS(mdev, &status);
@@ -442,15 +426,29 @@
}
mdev->cq_table.table = mthca_alloc_icm_table(mdev, init_hca->cqc_base,
- dev_lim->cqc_entry_sz,
- mdev->limits.num_cqs,
- mdev->limits.reserved_cqs, 0);
+ dev_lim->cqc_entry_sz,
+ mdev->limits.num_cqs,
+ mdev->limits.reserved_cqs, 0);
if (!mdev->cq_table.table) {
mthca_err(mdev, "Failed to map CQ context memory, aborting.\n");
err = -ENOMEM;
goto err_unmap_rdb;
}
+ if (mdev->mthca_flags & MTHCA_FLAG_SRQ) {
+ mdev->srq_table.table =
+ mthca_alloc_icm_table(mdev, init_hca->srqc_base,
+ dev_lim->srq_entry_sz,
+ mdev->limits.num_srqs,
+ mdev->limits.reserved_srqs, 0);
+ if (!mdev->srq_table.table) {
+ mthca_err(mdev, "Failed to map SRQ context memory, "
+ "aborting.\n");
+ err = -ENOMEM;
+ goto err_unmap_cq;
+ }
+ }
+
/*
* It's not strictly required, but for simplicity just map the
* whole multicast group table now. The table isn't very big
@@ -466,11 +464,15 @@
if (!mdev->mcg_table.table) {
mthca_err(mdev, "Failed to map MCG context memory, aborting.\n");
err = -ENOMEM;
- goto err_unmap_cq;
+ goto err_unmap_srq;
}
return 0;
+err_unmap_srq:
+ if (mdev->mthca_flags & MTHCA_FLAG_SRQ)
+ mthca_free_icm_table(mdev, mdev->srq_table.table);
+
err_unmap_cq:
mthca_free_icm_table(mdev, mdev->cq_table.table);
@@ -506,7 +508,6 @@
struct mthca_dev_lim dev_lim;
struct mthca_profile profile;
struct mthca_init_hca_param init_hca;
- struct mthca_adapter adapter;
u64 icm_size;
u8 status;
int err;
@@ -551,6 +552,8 @@
profile = default_profile;
profile.num_uar = dev_lim.uar_size / PAGE_SIZE;
profile.num_udav = 0;
+ if (mdev->mthca_flags & MTHCA_FLAG_SRQ)
+ profile.num_srq = dev_lim.max_srqs;
icm_size = mthca_make_profile(mdev, &profile, &dev_lim, &init_hca);
if ((int) icm_size < 0) {
@@ -574,24 +577,11 @@
goto err_free_icm;
}
- err = mthca_QUERY_ADAPTER(mdev, &adapter, &status);
- if (err) {
- mthca_err(mdev, "QUERY_ADAPTER command failed, aborting.\n");
- goto err_free_icm;
- }
- if (status) {
- mthca_err(mdev, "QUERY_ADAPTER returned status 0x%02x, "
- "aborting.\n", status);
- err = -EINVAL;
- goto err_free_icm;
- }
-
- mdev->eq_table.inta_pin = adapter.inta_pin;
- mdev->rev_id = adapter.revision_id;
-
return 0;
err_free_icm:
+ if (mdev->mthca_flags & MTHCA_FLAG_SRQ)
+ mthca_free_icm_table(mdev, mdev->srq_table.table);
mthca_free_icm_table(mdev, mdev->cq_table.table);
mthca_free_icm_table(mdev, mdev->qp_table.rdb_table);
mthca_free_icm_table(mdev, mdev->qp_table.eqp_table);
@@ -614,12 +604,70 @@
return err;
}
+static void mthca_close_hca(struct mthca_dev *mdev)
+{
+ u8 status;
+
+ mthca_CLOSE_HCA(mdev, 0, &status);
+
+ if (mthca_is_memfree(mdev)) {
+ if (mdev->mthca_flags & MTHCA_FLAG_SRQ)
+ mthca_free_icm_table(mdev, mdev->srq_table.table);
+ mthca_free_icm_table(mdev, mdev->cq_table.table);
+ mthca_free_icm_table(mdev, mdev->qp_table.rdb_table);
+ mthca_free_icm_table(mdev, mdev->qp_table.eqp_table);
+ mthca_free_icm_table(mdev, mdev->qp_table.qp_table);
+ mthca_free_icm_table(mdev, mdev->mr_table.mpt_table);
+ mthca_free_icm_table(mdev, mdev->mr_table.mtt_table);
+ mthca_unmap_eq_icm(mdev);
+
+ mthca_UNMAP_ICM_AUX(mdev, &status);
+ mthca_free_icm(mdev, mdev->fw.arbel.aux_icm);
+
+ mthca_UNMAP_FA(mdev, &status);
+ mthca_free_icm(mdev, mdev->fw.arbel.fw_icm);
+
+ if (!(mdev->mthca_flags & MTHCA_FLAG_NO_LAM))
+ mthca_DISABLE_LAM(mdev, &status);
+ } else
+ mthca_SYS_DIS(mdev, &status);
+}
+
static int __devinit mthca_init_hca(struct mthca_dev *mdev)
{
+ u8 status;
+ int err;
+ struct mthca_adapter adapter;
+
if (mthca_is_memfree(mdev))
- return mthca_init_arbel(mdev);
+ err = mthca_init_arbel(mdev);
else
- return mthca_init_tavor(mdev);
+ err = mthca_init_tavor(mdev);
+
+ if (err)
+ return err;
+
+ err = mthca_QUERY_ADAPTER(mdev, &adapter, &status);
+ if (err) {
+ mthca_err(mdev, "QUERY_ADAPTER command failed, aborting.\n");
+ goto err_close;
+ }
+ if (status) {
+ mthca_err(mdev, "QUERY_ADAPTER returned status 0x%02x, "
+ "aborting.\n", status);
+ err = -EINVAL;
+ goto err_close;
+ }
+
+ mdev->eq_table.inta_pin = adapter.inta_pin;
+ mdev->rev_id = adapter.revision_id;
+ memcpy(mdev->board_id, adapter.board_id, sizeof mdev->board_id);
+
+ return 0;
+
+err_close:
+ mthca_close_hca(mdev);
+ return err;
}
static int __devinit mthca_setup_hca(struct mthca_dev *dev)
@@ -709,11 +757,18 @@
goto err_cmd_poll;
}
+ err = mthca_init_srq_table(dev);
+ if (err) {
+ mthca_err(dev, "Failed to initialize "
+ "shared receive queue table, aborting.\n");
+ goto err_cq_table_free;
+ }
+
err = mthca_init_qp_table(dev);
if (err) {
mthca_err(dev, "Failed to initialize "
"queue pair table, aborting.\n");
- goto err_cq_table_free;
+ goto err_srq_table_free;
}
err = mthca_init_av_table(dev);
@@ -738,6 +793,9 @@
err_qp_table_free:
mthca_cleanup_qp_table(dev);
+err_srq_table_free:
+ mthca_cleanup_srq_table(dev);
+
err_cq_table_free:
mthca_cleanup_cq_table(dev);
@@ -844,33 +902,6 @@
return 0;
}
-static void mthca_close_hca(struct mthca_dev *mdev)
-{
- u8 status;
-
- mthca_CLOSE_HCA(mdev, 0, &status);
-
- if (mthca_is_memfree(mdev)) {
- mthca_free_icm_table(mdev, mdev->cq_table.table);
- mthca_free_icm_table(mdev, mdev->qp_table.rdb_table);
- mthca_free_icm_table(mdev, mdev->qp_table.eqp_table);
- mthca_free_icm_table(mdev, mdev->qp_table.qp_table);
- mthca_free_icm_table(mdev, mdev->mr_table.mpt_table);
- mthca_free_icm_table(mdev, mdev->mr_table.mtt_table);
- mthca_unmap_eq_icm(mdev);
-
- mthca_UNMAP_ICM_AUX(mdev, &status);
- mthca_free_icm(mdev, mdev->fw.arbel.aux_icm);
-
- mthca_UNMAP_FA(mdev, &status);
- mthca_free_icm(mdev, mdev->fw.arbel.fw_icm);
-
- if (!(mdev->mthca_flags & MTHCA_FLAG_NO_LAM))
- mthca_DISABLE_LAM(mdev, &status);
- } else
- mthca_SYS_DIS(mdev, &status);
-}
-
/* Types of supported HCA */
enum {
TAVOR, /* MT23108 */
@@ -887,9 +918,9 @@
int is_memfree;
int is_pcie;
} mthca_hca_table[] = {
- [TAVOR] = { .latest_fw = MTHCA_FW_VER(3, 3, 2), .is_memfree = 0, .is_pcie = 0 },
- [ARBEL_COMPAT] = { .latest_fw = MTHCA_FW_VER(4, 6, 2), .is_memfree = 0, .is_pcie = 1 },
- [ARBEL_NATIVE] = { .latest_fw = MTHCA_FW_VER(5, 0, 1), .is_memfree = 1, .is_pcie = 1 },
+ [TAVOR] = { .latest_fw = MTHCA_FW_VER(3, 3, 3), .is_memfree = 0, .is_pcie = 0 },
+ [ARBEL_COMPAT] = { .latest_fw = MTHCA_FW_VER(4, 7, 0), .is_memfree = 0, .is_pcie = 1 },
+ [ARBEL_NATIVE] = { .latest_fw = MTHCA_FW_VER(5, 1, 0), .is_memfree = 1, .is_pcie = 1 },
[SINAI] = { .latest_fw = MTHCA_FW_VER(1, 0, 1), .is_memfree = 1, .is_pcie = 1 }
};
@@ -1051,6 +1082,7 @@
mthca_cleanup_mcg_table(mdev);
mthca_cleanup_av_table(mdev);
mthca_cleanup_qp_table(mdev);
+ mthca_cleanup_srq_table(mdev);
mthca_cleanup_cq_table(mdev);
mthca_cmd_use_polling(mdev);
mthca_cleanup_eq_table(mdev);
@@ -1100,6 +1132,7 @@
mthca_cleanup_mcg_table(mdev);
mthca_cleanup_av_table(mdev);
mthca_cleanup_qp_table(mdev);
+ mthca_cleanup_srq_table(mdev);
mthca_cleanup_cq_table(mdev);
mthca_cmd_use_polling(mdev);
mthca_cleanup_eq_table(mdev);
diff --git a/drivers/infiniband/hw/mthca/mthca_mcg.c b/drivers/infiniband/hw/mthca/mthca_mcg.c
index 5be7d94..a270760 100644
--- a/drivers/infiniband/hw/mthca/mthca_mcg.c
+++ b/drivers/infiniband/hw/mthca/mthca_mcg.c
@@ -42,10 +42,10 @@
};
struct mthca_mgm {
- u32 next_gid_index;
- u32 reserved[3];
- u8 gid[16];
- u32 qp[MTHCA_QP_PER_MGM];
+ __be32 next_gid_index;
+ u32 reserved[3];
+ u8 gid[16];
+ __be32 qp[MTHCA_QP_PER_MGM];
};
static const u8 zero_gid[16]; /* automatically initialized to 0 */
@@ -94,10 +94,14 @@
if (0)
mthca_dbg(dev, "Hash for %04x:%04x:%04x:%04x:"
"%04x:%04x:%04x:%04x is %04x\n",
- be16_to_cpu(((u16 *) gid)[0]), be16_to_cpu(((u16 *) gid)[1]),
- be16_to_cpu(((u16 *) gid)[2]), be16_to_cpu(((u16 *) gid)[3]),
- be16_to_cpu(((u16 *) gid)[4]), be16_to_cpu(((u16 *) gid)[5]),
- be16_to_cpu(((u16 *) gid)[6]), be16_to_cpu(((u16 *) gid)[7]),
+ be16_to_cpu(((__be16 *) gid)[0]),
+ be16_to_cpu(((__be16 *) gid)[1]),
+ be16_to_cpu(((__be16 *) gid)[2]),
+ be16_to_cpu(((__be16 *) gid)[3]),
+ be16_to_cpu(((__be16 *) gid)[4]),
+ be16_to_cpu(((__be16 *) gid)[5]),
+ be16_to_cpu(((__be16 *) gid)[6]),
+ be16_to_cpu(((__be16 *) gid)[7]),
*hash);
*index = *hash;
@@ -258,14 +262,14 @@
if (index == -1) {
mthca_err(dev, "MGID %04x:%04x:%04x:%04x:%04x:%04x:%04x:%04x "
"not found\n",
- be16_to_cpu(((u16 *) gid->raw)[0]),
- be16_to_cpu(((u16 *) gid->raw)[1]),
- be16_to_cpu(((u16 *) gid->raw)[2]),
- be16_to_cpu(((u16 *) gid->raw)[3]),
- be16_to_cpu(((u16 *) gid->raw)[4]),
- be16_to_cpu(((u16 *) gid->raw)[5]),
- be16_to_cpu(((u16 *) gid->raw)[6]),
- be16_to_cpu(((u16 *) gid->raw)[7]));
+ be16_to_cpu(((__be16 *) gid->raw)[0]),
+ be16_to_cpu(((__be16 *) gid->raw)[1]),
+ be16_to_cpu(((__be16 *) gid->raw)[2]),
+ be16_to_cpu(((__be16 *) gid->raw)[3]),
+ be16_to_cpu(((__be16 *) gid->raw)[4]),
+ be16_to_cpu(((__be16 *) gid->raw)[5]),
+ be16_to_cpu(((__be16 *) gid->raw)[6]),
+ be16_to_cpu(((__be16 *) gid->raw)[7]));
err = -EINVAL;
goto out;
}
diff --git a/drivers/infiniband/hw/mthca/mthca_memfree.c b/drivers/infiniband/hw/mthca/mthca_memfree.c
index 2a864615..1827400 100644
--- a/drivers/infiniband/hw/mthca/mthca_memfree.c
+++ b/drivers/infiniband/hw/mthca/mthca_memfree.c
@@ -1,6 +1,7 @@
/*
* Copyright (c) 2004, 2005 Topspin Communications. All rights reserved.
* Copyright (c) 2005 Cisco Systems. All rights reserved.
+ * Copyright (c) 2005 Mellanox Technologies. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
@@ -285,6 +286,7 @@
{
struct mthca_icm_table *table;
int num_icm;
+ unsigned chunk_size;
int i;
u8 status;
@@ -305,7 +307,11 @@
table->icm[i] = NULL;
for (i = 0; i * MTHCA_TABLE_CHUNK_SIZE < reserved * obj_size; ++i) {
- table->icm[i] = mthca_alloc_icm(dev, MTHCA_TABLE_CHUNK_SIZE >> PAGE_SHIFT,
+ chunk_size = MTHCA_TABLE_CHUNK_SIZE;
+ if ((i + 1) * MTHCA_TABLE_CHUNK_SIZE > nobj * obj_size)
+ chunk_size = nobj * obj_size - i * MTHCA_TABLE_CHUNK_SIZE;
+
+ table->icm[i] = mthca_alloc_icm(dev, chunk_size >> PAGE_SHIFT,
(use_lowmem ? GFP_KERNEL : GFP_HIGHUSER) |
__GFP_NOWARN);
if (!table->icm[i])
@@ -481,7 +487,7 @@
}
}
-int mthca_alloc_db(struct mthca_dev *dev, int type, u32 qn, u32 **db)
+int mthca_alloc_db(struct mthca_dev *dev, int type, u32 qn, __be32 **db)
{
int group;
int start, end, dir;
@@ -564,7 +570,7 @@
page->db_rec[j] = cpu_to_be64((qn << 8) | (type << 5));
- *db = (u32 *) &page->db_rec[j];
+ *db = (__be32 *) &page->db_rec[j];
out:
up(&dev->db_tab->mutex);
diff --git a/drivers/infiniband/hw/mthca/mthca_memfree.h b/drivers/infiniband/hw/mthca/mthca_memfree.h
index 4761d84..bafa515 100644
--- a/drivers/infiniband/hw/mthca/mthca_memfree.h
+++ b/drivers/infiniband/hw/mthca/mthca_memfree.h
@@ -1,6 +1,7 @@
/*
* Copyright (c) 2004, 2005 Topspin Communications. All rights reserved.
* Copyright (c) 2005 Cisco Systems. All rights reserved.
+ * Copyright (c) 2005 Mellanox Technologies. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
@@ -137,7 +138,7 @@
struct mthca_db_page {
DECLARE_BITMAP(used, MTHCA_DB_REC_PER_PAGE);
- u64 *db_rec;
+ __be64 *db_rec;
dma_addr_t mapping;
};
@@ -172,7 +173,7 @@
int mthca_init_db_tab(struct mthca_dev *dev);
void mthca_cleanup_db_tab(struct mthca_dev *dev);
-int mthca_alloc_db(struct mthca_dev *dev, int type, u32 qn, u32 **db);
+int mthca_alloc_db(struct mthca_dev *dev, int type, u32 qn, __be32 **db);
void mthca_free_db(struct mthca_dev *dev, int type, int db_index);
#endif /* MTHCA_MEMFREE_H */
diff --git a/drivers/infiniband/hw/mthca/mthca_mr.c b/drivers/infiniband/hw/mthca/mthca_mr.c
index cbe50fe..1f97a44 100644
--- a/drivers/infiniband/hw/mthca/mthca_mr.c
+++ b/drivers/infiniband/hw/mthca/mthca_mr.c
@@ -1,5 +1,6 @@
/*
* Copyright (c) 2004 Topspin Communications. All rights reserved.
+ * Copyright (c) 2005 Mellanox Technologies. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
@@ -50,18 +51,18 @@
* Must be packed because mtt_seg is 64 bits but only aligned to 32 bits.
*/
struct mthca_mpt_entry {
- u32 flags;
- u32 page_size;
- u32 key;
- u32 pd;
- u64 start;
- u64 length;
- u32 lkey;
- u32 window_count;
- u32 window_count_limit;
- u64 mtt_seg;
- u32 mtt_sz; /* Arbel only */
- u32 reserved[2];
+ __be32 flags;
+ __be32 page_size;
+ __be32 key;
+ __be32 pd;
+ __be64 start;
+ __be64 length;
+ __be32 lkey;
+ __be32 window_count;
+ __be32 window_count_limit;
+ __be64 mtt_seg;
+ __be32 mtt_sz; /* Arbel only */
+ u32 reserved[2];
} __attribute__((packed));
#define MTHCA_MPT_FLAG_SW_OWNS (0xfUL << 28)
@@ -247,7 +248,7 @@
int start_index, u64 *buffer_list, int list_len)
{
struct mthca_mailbox *mailbox;
- u64 *mtt_entry;
+ __be64 *mtt_entry;
int err = 0;
u8 status;
int i;
@@ -389,7 +390,7 @@
for (i = 0; i < sizeof (struct mthca_mpt_entry) / 4; ++i) {
if (i % 4 == 0)
printk("[%02x] ", i * 4);
- printk(" %08x", be32_to_cpu(((u32 *) mpt_entry)[i]));
+ printk(" %08x", be32_to_cpu(((__be32 *) mpt_entry)[i]));
if ((i + 1) % 4 == 0)
printk("\n");
}
@@ -458,7 +459,7 @@
static void mthca_free_region(struct mthca_dev *dev, u32 lkey)
{
mthca_table_put(dev, dev->mr_table.mpt_table,
- arbel_key_to_hw_index(lkey));
+ key_to_hw_index(dev, lkey));
mthca_free(&dev->mr_table.mpt_alloc, key_to_hw_index(dev, lkey));
}
@@ -562,7 +563,7 @@
for (i = 0; i < sizeof (struct mthca_mpt_entry) / 4; ++i) {
if (i % 4 == 0)
printk("[%02x] ", i * 4);
- printk(" %08x", be32_to_cpu(((u32 *) mpt_entry)[i]));
+ printk(" %08x", be32_to_cpu(((__be32 *) mpt_entry)[i]));
if ((i + 1) % 4 == 0)
printk("\n");
}
@@ -669,7 +670,7 @@
mpt_entry.length = cpu_to_be64(list_len * (1ull << fmr->attr.page_size));
mpt_entry.start = cpu_to_be64(iova);
- writel(mpt_entry.lkey, &fmr->mem.tavor.mpt->key);
+ __raw_writel((__force u32) mpt_entry.lkey, &fmr->mem.tavor.mpt->key);
memcpy_toio(&fmr->mem.tavor.mpt->start, &mpt_entry.start,
offsetof(struct mthca_mpt_entry, window_count) -
offsetof(struct mthca_mpt_entry, start));
diff --git a/drivers/infiniband/hw/mthca/mthca_pd.c b/drivers/infiniband/hw/mthca/mthca_pd.c
index c2c8998..3dbf06a 100644
--- a/drivers/infiniband/hw/mthca/mthca_pd.c
+++ b/drivers/infiniband/hw/mthca/mthca_pd.c
@@ -1,6 +1,7 @@
/*
* Copyright (c) 2004 Topspin Communications. All rights reserved.
* Copyright (c) 2005 Cisco Systems. All rights reserved.
+ * Copyright (c) 2005 Mellanox Technologies. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
diff --git a/drivers/infiniband/hw/mthca/mthca_profile.c b/drivers/infiniband/hw/mthca/mthca_profile.c
index 4fedc32..0576056 100644
--- a/drivers/infiniband/hw/mthca/mthca_profile.c
+++ b/drivers/infiniband/hw/mthca/mthca_profile.c
@@ -1,5 +1,6 @@
/*
* Copyright (c) 2004, 2005 Topspin Communications. All rights reserved.
+ * Copyright (c) 2005 Mellanox Technologies. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
@@ -101,6 +102,7 @@
profile[MTHCA_RES_UARC].size = request->uarc_size;
profile[MTHCA_RES_QP].num = request->num_qp;
+ profile[MTHCA_RES_SRQ].num = request->num_srq;
profile[MTHCA_RES_EQP].num = request->num_qp;
profile[MTHCA_RES_RDB].num = request->num_qp * request->rdb_per_qp;
profile[MTHCA_RES_CQ].num = request->num_cq;
diff --git a/drivers/infiniband/hw/mthca/mthca_profile.h b/drivers/infiniband/hw/mthca/mthca_profile.h
index 17aef33..9464180 100644
--- a/drivers/infiniband/hw/mthca/mthca_profile.h
+++ b/drivers/infiniband/hw/mthca/mthca_profile.h
@@ -1,5 +1,6 @@
/*
* Copyright (c) 2004, 2005 Topspin Communications. All rights reserved.
+ * Copyright (c) 2005 Mellanox Technologies. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
@@ -41,6 +42,7 @@
struct mthca_profile {
int num_qp;
int rdb_per_qp;
+ int num_srq;
int num_cq;
int num_mcg;
int num_mpt;
diff --git a/drivers/infiniband/hw/mthca/mthca_provider.c b/drivers/infiniband/hw/mthca/mthca_provider.c
index 81919a7..1c1c2e2 100644
--- a/drivers/infiniband/hw/mthca/mthca_provider.c
+++ b/drivers/infiniband/hw/mthca/mthca_provider.c
@@ -2,6 +2,8 @@
* Copyright (c) 2004, 2005 Topspin Communications. All rights reserved.
* Copyright (c) 2005 Sun Microsystems, Inc. All rights reserved.
* Copyright (c) 2005 Cisco Systems. All rights reserved.
+ * Copyright (c) 2005 Mellanox Technologies. All rights reserved.
+ * Copyright (c) 2004 Voltaire, Inc. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
@@ -34,7 +36,7 @@
* $Id: mthca_provider.c 1397 2004-12-28 05:09:00Z roland $
*/
-#include <ib_smi.h>
+#include <rdma/ib_smi.h>
#include <linux/mm.h>
#include "mthca_dev.h"
@@ -79,10 +81,10 @@
}
props->device_cap_flags = mdev->device_cap_flags;
- props->vendor_id = be32_to_cpup((u32 *) (out_mad->data + 36)) &
+ props->vendor_id = be32_to_cpup((__be32 *) (out_mad->data + 36)) &
0xffffff;
- props->vendor_part_id = be16_to_cpup((u16 *) (out_mad->data + 30));
- props->hw_ver = be16_to_cpup((u16 *) (out_mad->data + 32));
+ props->vendor_part_id = be16_to_cpup((__be16 *) (out_mad->data + 30));
+ props->hw_ver = be16_to_cpup((__be16 *) (out_mad->data + 32));
memcpy(&props->sys_image_guid, out_mad->data + 4, 8);
memcpy(&props->node_guid, out_mad->data + 12, 8);
@@ -118,6 +120,8 @@
if (!in_mad || !out_mad)
goto out;
+ memset(props, 0, sizeof *props);
+
memset(in_mad, 0, sizeof *in_mad);
in_mad->base_version = 1;
in_mad->mgmt_class = IB_MGMT_CLASS_SUBN_LID_ROUTED;
@@ -136,16 +140,17 @@
goto out;
}
- props->lid = be16_to_cpup((u16 *) (out_mad->data + 16));
+ props->lid = be16_to_cpup((__be16 *) (out_mad->data + 16));
props->lmc = out_mad->data[34] & 0x7;
- props->sm_lid = be16_to_cpup((u16 *) (out_mad->data + 18));
+ props->sm_lid = be16_to_cpup((__be16 *) (out_mad->data + 18));
props->sm_sl = out_mad->data[36] & 0xf;
props->state = out_mad->data[32] & 0xf;
props->phys_state = out_mad->data[33] >> 4;
- props->port_cap_flags = be32_to_cpup((u32 *) (out_mad->data + 20));
+ props->port_cap_flags = be32_to_cpup((__be32 *) (out_mad->data + 20));
props->gid_tbl_len = to_mdev(ibdev)->limits.gid_table_len;
+ props->max_msg_sz = 0x80000000;
props->pkey_tbl_len = to_mdev(ibdev)->limits.pkey_table_len;
- props->qkey_viol_cntr = be16_to_cpup((u16 *) (out_mad->data + 48));
+ props->qkey_viol_cntr = be16_to_cpup((__be16 *) (out_mad->data + 48));
props->active_width = out_mad->data[31] & 0xf;
props->active_speed = out_mad->data[35] >> 4;
@@ -221,7 +226,7 @@
goto out;
}
- *pkey = be16_to_cpu(((u16 *) out_mad->data)[index % 32]);
+ *pkey = be16_to_cpu(((__be16 *) out_mad->data)[index % 32]);
out:
kfree(in_mad);
@@ -420,6 +425,77 @@
return 0;
}
+static struct ib_srq *mthca_create_srq(struct ib_pd *pd,
+ struct ib_srq_init_attr *init_attr,
+ struct ib_udata *udata)
+{
+ struct mthca_create_srq ucmd;
+ struct mthca_ucontext *context = NULL;
+ struct mthca_srq *srq;
+ int err;
+
+ srq = kmalloc(sizeof *srq, GFP_KERNEL);
+ if (!srq)
+ return ERR_PTR(-ENOMEM);
+
+ if (pd->uobject) {
+ context = to_mucontext(pd->uobject->context);
+
+ if (ib_copy_from_udata(&ucmd, udata, sizeof ucmd))
+ return ERR_PTR(-EFAULT);
+
+ err = mthca_map_user_db(to_mdev(pd->device), &context->uar,
+ context->db_tab, ucmd.db_index,
+ ucmd.db_page);
+
+ if (err)
+ goto err_free;
+
+ srq->mr.ibmr.lkey = ucmd.lkey;
+ srq->db_index = ucmd.db_index;
+ }
+
+ err = mthca_alloc_srq(to_mdev(pd->device), to_mpd(pd),
+ &init_attr->attr, srq);
+
+ if (err && pd->uobject)
+ mthca_unmap_user_db(to_mdev(pd->device), &context->uar,
+ context->db_tab, ucmd.db_index);
+
+ if (err)
+ goto err_free;
+
+ if (context && ib_copy_to_udata(udata, &srq->srqn, sizeof (__u32))) {
+ mthca_free_srq(to_mdev(pd->device), srq);
+ err = -EFAULT;
+ goto err_free;
+ }
+
+ return &srq->ibsrq;
+
+err_free:
+ kfree(srq);
+
+ return ERR_PTR(err);
+}
+
+static int mthca_destroy_srq(struct ib_srq *srq)
+{
+ struct mthca_ucontext *context;
+
+ if (srq->uobject) {
+ context = to_mucontext(srq->uobject->context);
+
+ mthca_unmap_user_db(to_mdev(srq->device), &context->uar,
+ context->db_tab, to_msrq(srq)->db_index);
+ }
+
+ mthca_free_srq(to_mdev(srq->device), to_msrq(srq));
+ kfree(srq);
+
+ return 0;
+}
+
static struct ib_qp *mthca_create_qp(struct ib_pd *pd,
struct ib_qp_init_attr *init_attr,
struct ib_udata *udata)
@@ -956,14 +1032,22 @@
}
}
+static ssize_t show_board(struct class_device *cdev, char *buf)
+{
+ struct mthca_dev *dev = container_of(cdev, struct mthca_dev, ib_dev.class_dev);
+ return sprintf(buf, "%.*s\n", MTHCA_BOARD_ID_LEN, dev->board_id);
+}
+
static CLASS_DEVICE_ATTR(hw_rev, S_IRUGO, show_rev, NULL);
static CLASS_DEVICE_ATTR(fw_ver, S_IRUGO, show_fw_ver, NULL);
static CLASS_DEVICE_ATTR(hca_type, S_IRUGO, show_hca, NULL);
+static CLASS_DEVICE_ATTR(board_id, S_IRUGO, show_board, NULL);
static struct class_device_attribute *mthca_class_attributes[] = {
&class_device_attr_hw_rev,
&class_device_attr_fw_ver,
- &class_device_attr_hca_type
+ &class_device_attr_hca_type,
+ &class_device_attr_board_id
};
int mthca_register_device(struct mthca_dev *dev)
@@ -990,6 +1074,17 @@
dev->ib_dev.dealloc_pd = mthca_dealloc_pd;
dev->ib_dev.create_ah = mthca_ah_create;
dev->ib_dev.destroy_ah = mthca_ah_destroy;
+
+ if (dev->mthca_flags & MTHCA_FLAG_SRQ) {
+ dev->ib_dev.create_srq = mthca_create_srq;
+ dev->ib_dev.destroy_srq = mthca_destroy_srq;
+
+ if (mthca_is_memfree(dev))
+ dev->ib_dev.post_srq_recv = mthca_arbel_post_srq_recv;
+ else
+ dev->ib_dev.post_srq_recv = mthca_tavor_post_srq_recv;
+ }
+
dev->ib_dev.create_qp = mthca_create_qp;
dev->ib_dev.modify_qp = mthca_modify_qp;
dev->ib_dev.destroy_qp = mthca_destroy_qp;
diff --git a/drivers/infiniband/hw/mthca/mthca_provider.h b/drivers/infiniband/hw/mthca/mthca_provider.h
index 1d03279..bcd4b01 100644
--- a/drivers/infiniband/hw/mthca/mthca_provider.h
+++ b/drivers/infiniband/hw/mthca/mthca_provider.h
@@ -1,6 +1,7 @@
/*
* Copyright (c) 2004 Topspin Communications. All rights reserved.
* Copyright (c) 2005 Cisco Systems. All rights reserved.
+ * Copyright (c) 2005 Mellanox Technologies. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
@@ -36,8 +37,8 @@
#ifndef MTHCA_PROVIDER_H
#define MTHCA_PROVIDER_H
-#include <ib_verbs.h>
-#include <ib_pack.h>
+#include <rdma/ib_verbs.h>
+#include <rdma/ib_pack.h>
#define MTHCA_MPT_FLAG_ATOMIC (1 << 14)
#define MTHCA_MPT_FLAG_REMOTE_WRITE (1 << 13)
@@ -50,6 +51,11 @@
DECLARE_PCI_UNMAP_ADDR(mapping)
};
+union mthca_buf {
+ struct mthca_buf_list direct;
+ struct mthca_buf_list *page_list;
+};
+
struct mthca_uar {
unsigned long pfn;
int index;
@@ -181,19 +187,39 @@
/* Next fields are Arbel only */
int set_ci_db_index;
- u32 *set_ci_db;
+ __be32 *set_ci_db;
int arm_db_index;
- u32 *arm_db;
+ __be32 *arm_db;
int arm_sn;
- union {
- struct mthca_buf_list direct;
- struct mthca_buf_list *page_list;
- } queue;
+ union mthca_buf queue;
struct mthca_mr mr;
wait_queue_head_t wait;
};
+struct mthca_srq {
+ struct ib_srq ibsrq;
+ spinlock_t lock;
+ atomic_t refcount;
+ int srqn;
+ int max;
+ int max_gs;
+ int wqe_shift;
+ int first_free;
+ int last_free;
+ u16 counter; /* Arbel only */
+ int db_index; /* Arbel only */
+ __be32 *db; /* Arbel only */
+ void *last;
+
+ int is_direct;
+ u64 *wrid;
+ union mthca_buf queue;
+ struct mthca_mr mr;
+
+ wait_queue_head_t wait;
+};
+
struct mthca_wq {
spinlock_t lock;
int max;
@@ -206,7 +232,7 @@
int wqe_shift;
int db_index; /* Arbel only */
- u32 *db;
+ __be32 *db;
};
struct mthca_qp {
@@ -227,10 +253,7 @@
int send_wqe_offset;
u64 *wrid;
- union {
- struct mthca_buf_list direct;
- struct mthca_buf_list *page_list;
- } queue;
+ union mthca_buf queue;
wait_queue_head_t wait;
};
@@ -277,6 +300,11 @@
return container_of(ibcq, struct mthca_cq, ibcq);
}
+static inline struct mthca_srq *to_msrq(struct ib_srq *ibsrq)
+{
+ return container_of(ibsrq, struct mthca_srq, ibsrq);
+}
+
static inline struct mthca_qp *to_mqp(struct ib_qp *ibqp)
{
return container_of(ibqp, struct mthca_qp, ibqp);
diff --git a/drivers/infiniband/hw/mthca/mthca_qp.c b/drivers/infiniband/hw/mthca/mthca_qp.c
index f7126b1..0164b84 100644
--- a/drivers/infiniband/hw/mthca/mthca_qp.c
+++ b/drivers/infiniband/hw/mthca/mthca_qp.c
@@ -1,6 +1,8 @@
/*
* Copyright (c) 2004 Topspin Communications. All rights reserved.
* Copyright (c) 2005 Cisco Systems. All rights reserved.
+ * Copyright (c) 2005 Mellanox Technologies. All rights reserved.
+ * Copyright (c) 2004 Voltaire, Inc. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
@@ -35,13 +37,14 @@
#include <linux/init.h>
-#include <ib_verbs.h>
-#include <ib_cache.h>
-#include <ib_pack.h>
+#include <rdma/ib_verbs.h>
+#include <rdma/ib_cache.h>
+#include <rdma/ib_pack.h>
#include "mthca_dev.h"
#include "mthca_cmd.h"
#include "mthca_memfree.h"
+#include "mthca_wqe.h"
enum {
MTHCA_MAX_DIRECT_QP_SIZE = 4 * PAGE_SIZE,
@@ -95,62 +98,62 @@
};
struct mthca_qp_path {
- u32 port_pkey;
- u8 rnr_retry;
- u8 g_mylmc;
- u16 rlid;
- u8 ackto;
- u8 mgid_index;
- u8 static_rate;
- u8 hop_limit;
- u32 sl_tclass_flowlabel;
- u8 rgid[16];
+ __be32 port_pkey;
+ u8 rnr_retry;
+ u8 g_mylmc;
+ __be16 rlid;
+ u8 ackto;
+ u8 mgid_index;
+ u8 static_rate;
+ u8 hop_limit;
+ __be32 sl_tclass_flowlabel;
+ u8 rgid[16];
} __attribute__((packed));
struct mthca_qp_context {
- u32 flags;
- u32 tavor_sched_queue; /* Reserved on Arbel */
- u8 mtu_msgmax;
- u8 rq_size_stride; /* Reserved on Tavor */
- u8 sq_size_stride; /* Reserved on Tavor */
- u8 rlkey_arbel_sched_queue; /* Reserved on Tavor */
- u32 usr_page;
- u32 local_qpn;
- u32 remote_qpn;
- u32 reserved1[2];
+ __be32 flags;
+ __be32 tavor_sched_queue; /* Reserved on Arbel */
+ u8 mtu_msgmax;
+ u8 rq_size_stride; /* Reserved on Tavor */
+ u8 sq_size_stride; /* Reserved on Tavor */
+ u8 rlkey_arbel_sched_queue; /* Reserved on Tavor */
+ __be32 usr_page;
+ __be32 local_qpn;
+ __be32 remote_qpn;
+ u32 reserved1[2];
struct mthca_qp_path pri_path;
struct mthca_qp_path alt_path;
- u32 rdd;
- u32 pd;
- u32 wqe_base;
- u32 wqe_lkey;
- u32 params1;
- u32 reserved2;
- u32 next_send_psn;
- u32 cqn_snd;
- u32 snd_wqe_base_l; /* Next send WQE on Tavor */
- u32 snd_db_index; /* (debugging only entries) */
- u32 last_acked_psn;
- u32 ssn;
- u32 params2;
- u32 rnr_nextrecvpsn;
- u32 ra_buff_indx;
- u32 cqn_rcv;
- u32 rcv_wqe_base_l; /* Next recv WQE on Tavor */
- u32 rcv_db_index; /* (debugging only entries) */
- u32 qkey;
- u32 srqn;
- u32 rmsn;
- u16 rq_wqe_counter; /* reserved on Tavor */
- u16 sq_wqe_counter; /* reserved on Tavor */
- u32 reserved3[18];
+ __be32 rdd;
+ __be32 pd;
+ __be32 wqe_base;
+ __be32 wqe_lkey;
+ __be32 params1;
+ __be32 reserved2;
+ __be32 next_send_psn;
+ __be32 cqn_snd;
+ __be32 snd_wqe_base_l; /* Next send WQE on Tavor */
+ __be32 snd_db_index; /* (debugging only entries) */
+ __be32 last_acked_psn;
+ __be32 ssn;
+ __be32 params2;
+ __be32 rnr_nextrecvpsn;
+ __be32 ra_buff_indx;
+ __be32 cqn_rcv;
+ __be32 rcv_wqe_base_l; /* Next recv WQE on Tavor */
+ __be32 rcv_db_index; /* (debugging only entries) */
+ __be32 qkey;
+ __be32 srqn;
+ __be32 rmsn;
+ __be16 rq_wqe_counter; /* reserved on Tavor */
+ __be16 sq_wqe_counter; /* reserved on Tavor */
+ u32 reserved3[18];
} __attribute__((packed));
struct mthca_qp_param {
- u32 opt_param_mask;
- u32 reserved1;
+ __be32 opt_param_mask;
+ u32 reserved1;
struct mthca_qp_context context;
- u32 reserved2[62];
+ u32 reserved2[62];
} __attribute__((packed));
enum {
@@ -173,80 +176,6 @@
MTHCA_QP_OPTPAR_SCHED_QUEUE = 1 << 16
};
-enum {
- MTHCA_NEXT_DBD = 1 << 7,
- MTHCA_NEXT_FENCE = 1 << 6,
- MTHCA_NEXT_CQ_UPDATE = 1 << 3,
- MTHCA_NEXT_EVENT_GEN = 1 << 2,
- MTHCA_NEXT_SOLICIT = 1 << 1,
-
- MTHCA_MLX_VL15 = 1 << 17,
- MTHCA_MLX_SLR = 1 << 16
-};
-
-enum {
- MTHCA_INVAL_LKEY = 0x100
-};
-
-struct mthca_next_seg {
- u32 nda_op; /* [31:6] next WQE [4:0] next opcode */
- u32 ee_nds; /* [31:8] next EE [7] DBD [6] F [5:0] next WQE size */
- u32 flags; /* [3] CQ [2] Event [1] Solicit */
- u32 imm; /* immediate data */
-};
-
-struct mthca_tavor_ud_seg {
- u32 reserved1;
- u32 lkey;
- u64 av_addr;
- u32 reserved2[4];
- u32 dqpn;
- u32 qkey;
- u32 reserved3[2];
-};
-
-struct mthca_arbel_ud_seg {
- u32 av[8];
- u32 dqpn;
- u32 qkey;
- u32 reserved[2];
-};
-
-struct mthca_bind_seg {
- u32 flags; /* [31] Atomic [30] rem write [29] rem read */
- u32 reserved;
- u32 new_rkey;
- u32 lkey;
- u64 addr;
- u64 length;
-};
-
-struct mthca_raddr_seg {
- u64 raddr;
- u32 rkey;
- u32 reserved;
-};
-
-struct mthca_atomic_seg {
- u64 swap_add;
- u64 compare;
-};
-
-struct mthca_data_seg {
- u32 byte_count;
- u32 lkey;
- u64 addr;
-};
-
-struct mthca_mlx_seg {
- u32 nda_op;
- u32 nds;
- u32 flags; /* [17] VL15 [16] SLR [14:12] static rate
- [11:8] SL [3] C [2] E */
- u16 rlid;
- u16 vcrc;
-};
-
static const u8 mthca_opcode[] = {
[IB_WR_SEND] = MTHCA_OPCODE_SEND,
[IB_WR_SEND_WITH_IMM] = MTHCA_OPCODE_SEND_IMM,
@@ -573,12 +502,11 @@
memset(¶m, 0, sizeof param);
- param.enable_1x = 1;
- param.enable_4x = 1;
- param.vl_cap = dev->limits.vl_cap;
- param.mtu_cap = dev->limits.mtu_cap;
- param.gid_cap = dev->limits.gid_table_len;
- param.pkey_cap = dev->limits.pkey_table_len;
+ param.port_width = dev->limits.port_width_cap;
+ param.vl_cap = dev->limits.vl_cap;
+ param.mtu_cap = dev->limits.mtu_cap;
+ param.gid_cap = dev->limits.gid_table_len;
+ param.pkey_cap = dev->limits.pkey_table_len;
err = mthca_INIT_IB(dev, ¶m, port, &status);
if (err)
@@ -684,10 +612,13 @@
qp_context->mtu_msgmax = (attr->path_mtu << 5) | 31;
if (mthca_is_memfree(dev)) {
- qp_context->rq_size_stride =
- ((ffs(qp->rq.max) - 1) << 3) | (qp->rq.wqe_shift - 4);
- qp_context->sq_size_stride =
- ((ffs(qp->sq.max) - 1) << 3) | (qp->sq.wqe_shift - 4);
+ if (qp->rq.max)
+ qp_context->rq_size_stride = long_log2(qp->rq.max) << 3;
+ qp_context->rq_size_stride |= qp->rq.wqe_shift - 4;
+
+ if (qp->sq.max)
+ qp_context->sq_size_stride = long_log2(qp->sq.max) << 3;
+ qp_context->sq_size_stride |= qp->sq.wqe_shift - 4;
}
/* leave arbel_sched_queue as 0 */
@@ -856,6 +787,9 @@
qp_context->params2 |= cpu_to_be32(MTHCA_QP_BIT_RSC);
+ if (ibqp->srq)
+ qp_context->params2 |= cpu_to_be32(MTHCA_QP_BIT_RIC);
+
if (attr_mask & IB_QP_MIN_RNR_TIMER) {
qp_context->rnr_nextrecvpsn |= cpu_to_be32(attr->min_rnr_timer << 24);
qp_param->opt_param_mask |= cpu_to_be32(MTHCA_QP_OPTPAR_RNR_TIMEOUT);
@@ -878,6 +812,10 @@
qp_param->opt_param_mask |= cpu_to_be32(MTHCA_QP_OPTPAR_Q_KEY);
}
+ if (ibqp->srq)
+ qp_context->srqn = cpu_to_be32(1 << 24 |
+ to_msrq(ibqp->srq)->srqn);
+
err = mthca_MODIFY_QP(dev, state_table[cur_state][new_state].trans,
qp->qpn, 0, mailbox, 0, &status);
if (status) {
@@ -925,10 +863,6 @@
struct mthca_qp *qp)
{
int size;
- int i;
- int npages, shift;
- dma_addr_t t;
- u64 *dma_list = NULL;
int err = -ENOMEM;
size = sizeof (struct mthca_next_seg) +
@@ -978,116 +912,24 @@
if (!qp->wrid)
goto err_out;
- if (size <= MTHCA_MAX_DIRECT_QP_SIZE) {
- qp->is_direct = 1;
- npages = 1;
- shift = get_order(size) + PAGE_SHIFT;
-
- if (0)
- mthca_dbg(dev, "Creating direct QP of size %d (shift %d)\n",
- size, shift);
-
- qp->queue.direct.buf = dma_alloc_coherent(&dev->pdev->dev, size,
- &t, GFP_KERNEL);
- if (!qp->queue.direct.buf)
- goto err_out;
-
- pci_unmap_addr_set(&qp->queue.direct, mapping, t);
-
- memset(qp->queue.direct.buf, 0, size);
-
- while (t & ((1 << shift) - 1)) {
- --shift;
- npages *= 2;
- }
-
- dma_list = kmalloc(npages * sizeof *dma_list, GFP_KERNEL);
- if (!dma_list)
- goto err_out_free;
-
- for (i = 0; i < npages; ++i)
- dma_list[i] = t + i * (1 << shift);
- } else {
- qp->is_direct = 0;
- npages = size / PAGE_SIZE;
- shift = PAGE_SHIFT;
-
- if (0)
- mthca_dbg(dev, "Creating indirect QP with %d pages\n", npages);
-
- dma_list = kmalloc(npages * sizeof *dma_list, GFP_KERNEL);
- if (!dma_list)
- goto err_out;
-
- qp->queue.page_list = kmalloc(npages *
- sizeof *qp->queue.page_list,
- GFP_KERNEL);
- if (!qp->queue.page_list)
- goto err_out;
-
- for (i = 0; i < npages; ++i) {
- qp->queue.page_list[i].buf =
- dma_alloc_coherent(&dev->pdev->dev, PAGE_SIZE,
- &t, GFP_KERNEL);
- if (!qp->queue.page_list[i].buf)
- goto err_out_free;
-
- memset(qp->queue.page_list[i].buf, 0, PAGE_SIZE);
-
- pci_unmap_addr_set(&qp->queue.page_list[i], mapping, t);
- dma_list[i] = t;
- }
- }
-
- err = mthca_mr_alloc_phys(dev, pd->pd_num, dma_list, shift,
- npages, 0, size,
- MTHCA_MPT_FLAG_LOCAL_READ,
- &qp->mr);
+ err = mthca_buf_alloc(dev, size, MTHCA_MAX_DIRECT_QP_SIZE,
+ &qp->queue, &qp->is_direct, pd, 0, &qp->mr);
if (err)
- goto err_out_free;
+ goto err_out;
- kfree(dma_list);
return 0;
- err_out_free:
- if (qp->is_direct) {
- dma_free_coherent(&dev->pdev->dev, size, qp->queue.direct.buf,
- pci_unmap_addr(&qp->queue.direct, mapping));
- } else
- for (i = 0; i < npages; ++i) {
- if (qp->queue.page_list[i].buf)
- dma_free_coherent(&dev->pdev->dev, PAGE_SIZE,
- qp->queue.page_list[i].buf,
- pci_unmap_addr(&qp->queue.page_list[i],
- mapping));
-
- }
-
- err_out:
+err_out:
kfree(qp->wrid);
- kfree(dma_list);
return err;
}
static void mthca_free_wqe_buf(struct mthca_dev *dev,
struct mthca_qp *qp)
{
- int i;
- int size = PAGE_ALIGN(qp->send_wqe_offset +
- (qp->sq.max << qp->sq.wqe_shift));
-
- if (qp->is_direct) {
- dma_free_coherent(&dev->pdev->dev, size, qp->queue.direct.buf,
- pci_unmap_addr(&qp->queue.direct, mapping));
- } else {
- for (i = 0; i < size / PAGE_SIZE; ++i) {
- dma_free_coherent(&dev->pdev->dev, PAGE_SIZE,
- qp->queue.page_list[i].buf,
- pci_unmap_addr(&qp->queue.page_list[i],
- mapping));
- }
- }
-
+ mthca_buf_free(dev, PAGE_ALIGN(qp->send_wqe_offset +
+ (qp->sq.max << qp->sq.wqe_shift)),
+ &qp->queue, qp->is_direct, &qp->mr);
kfree(qp->wrid);
}
@@ -1428,11 +1270,12 @@
* unref the mem-free tables and free the QPN in our table.
*/
if (!qp->ibqp.uobject) {
- mthca_cq_clean(dev, to_mcq(qp->ibqp.send_cq)->cqn, qp->qpn);
+ mthca_cq_clean(dev, to_mcq(qp->ibqp.send_cq)->cqn, qp->qpn,
+ qp->ibqp.srq ? to_msrq(qp->ibqp.srq) : NULL);
if (qp->ibqp.send_cq != qp->ibqp.recv_cq)
- mthca_cq_clean(dev, to_mcq(qp->ibqp.recv_cq)->cqn, qp->qpn);
+ mthca_cq_clean(dev, to_mcq(qp->ibqp.recv_cq)->cqn, qp->qpn,
+ qp->ibqp.srq ? to_msrq(qp->ibqp.srq) : NULL);
- mthca_free_mr(dev, &qp->mr);
mthca_free_memfree(dev, qp);
mthca_free_wqe_buf(dev, qp);
}
@@ -1457,6 +1300,7 @@
{
int header_size;
int err;
+ u16 pkey;
ib_ud_header_init(256, /* assume a MAD */
sqp->ud_header.grh_present,
@@ -1467,8 +1311,8 @@
return err;
mlx->flags &= ~cpu_to_be32(MTHCA_NEXT_SOLICIT | 1);
mlx->flags |= cpu_to_be32((!sqp->qp.ibqp.qp_num ? MTHCA_MLX_VL15 : 0) |
- (sqp->ud_header.lrh.destination_lid == 0xffff ?
- MTHCA_MLX_SLR : 0) |
+ (sqp->ud_header.lrh.destination_lid ==
+ IB_LID_PERMISSIVE ? MTHCA_MLX_SLR : 0) |
(sqp->ud_header.lrh.service_level << 8));
mlx->rlid = sqp->ud_header.lrh.destination_lid;
mlx->vcrc = 0;
@@ -1488,18 +1332,16 @@
}
sqp->ud_header.lrh.virtual_lane = !sqp->qp.ibqp.qp_num ? 15 : 0;
- if (sqp->ud_header.lrh.destination_lid == 0xffff)
- sqp->ud_header.lrh.source_lid = 0xffff;
+ if (sqp->ud_header.lrh.destination_lid == IB_LID_PERMISSIVE)
+ sqp->ud_header.lrh.source_lid = IB_LID_PERMISSIVE;
sqp->ud_header.bth.solicited_event = !!(wr->send_flags & IB_SEND_SOLICITED);
if (!sqp->qp.ibqp.qp_num)
ib_get_cached_pkey(&dev->ib_dev, sqp->port,
- sqp->pkey_index,
- &sqp->ud_header.bth.pkey);
+ sqp->pkey_index, &pkey);
else
ib_get_cached_pkey(&dev->ib_dev, sqp->port,
- wr->wr.ud.pkey_index,
- &sqp->ud_header.bth.pkey);
- cpu_to_be16s(&sqp->ud_header.bth.pkey);
+ wr->wr.ud.pkey_index, &pkey);
+ sqp->ud_header.bth.pkey = cpu_to_be16(pkey);
sqp->ud_header.bth.destination_qpn = cpu_to_be32(wr->wr.ud.remote_qpn);
sqp->ud_header.bth.psn = cpu_to_be32((sqp->send_psn++) & ((1 << 24) - 1));
sqp->ud_header.deth.qkey = cpu_to_be32(wr->wr.ud.remote_qkey & 0x80000000 ?
@@ -1742,7 +1584,7 @@
out:
if (likely(nreq)) {
- u32 doorbell[2];
+ __be32 doorbell[2];
doorbell[0] = cpu_to_be32(((qp->sq.next_ind << qp->sq.wqe_shift) +
qp->send_wqe_offset) | f0 | op0);
@@ -1843,7 +1685,7 @@
out:
if (likely(nreq)) {
- u32 doorbell[2];
+ __be32 doorbell[2];
doorbell[0] = cpu_to_be32((qp->rq.next_ind << qp->rq.wqe_shift) | size0);
doorbell[1] = cpu_to_be32((qp->qpn << 8) | nreq);
@@ -2064,7 +1906,7 @@
out:
if (likely(nreq)) {
- u32 doorbell[2];
+ __be32 doorbell[2];
doorbell[0] = cpu_to_be32((nreq << 24) |
((qp->sq.head & 0xffff) << 8) |
@@ -2174,19 +2016,25 @@
}
int mthca_free_err_wqe(struct mthca_dev *dev, struct mthca_qp *qp, int is_send,
- int index, int *dbd, u32 *new_wqe)
+ int index, int *dbd, __be32 *new_wqe)
{
struct mthca_next_seg *next;
+ /*
+ * For SRQs, all WQEs generate a CQE, so we're always at the
+ * end of the doorbell chain.
+ */
+ if (qp->ibqp.srq) {
+ *new_wqe = 0;
+ return 0;
+ }
+
if (is_send)
next = get_send_wqe(qp, index);
else
next = get_recv_wqe(qp, index);
- if (mthca_is_memfree(dev))
- *dbd = 1;
- else
- *dbd = !!(next->ee_nds & cpu_to_be32(MTHCA_NEXT_DBD));
+ *dbd = !!(next->ee_nds & cpu_to_be32(MTHCA_NEXT_DBD));
if (next->ee_nds & cpu_to_be32(0x3f))
*new_wqe = (next->nda_op & cpu_to_be32(~0x3f)) |
(next->ee_nds & cpu_to_be32(0x3f));
diff --git a/drivers/infiniband/hw/mthca/mthca_srq.c b/drivers/infiniband/hw/mthca/mthca_srq.c
new file mode 100644
index 0000000..75cd2d8
--- /dev/null
+++ b/drivers/infiniband/hw/mthca/mthca_srq.c
@@ -0,0 +1,591 @@
+/*
+ * Copyright (c) 2005 Cisco Systems. All rights reserved.
+ *
+ * This software is available to you under a choice of one of two
+ * licenses. You may choose to be licensed under the terms of the GNU
+ * General Public License (GPL) Version 2, available from the file
+ * COPYING in the main directory of this source tree, or the
+ * OpenIB.org BSD license below:
+ *
+ * Redistribution and use in source and binary forms, with or
+ * without modification, are permitted provided that the following
+ * conditions are met:
+ *
+ * - Redistributions of source code must retain the above
+ * copyright notice, this list of conditions and the following
+ * disclaimer.
+ *
+ * - Redistributions in binary form must reproduce the above
+ * copyright notice, this list of conditions and the following
+ * disclaimer in the documentation and/or other materials
+ * provided with the distribution.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
+ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS
+ * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN
+ * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
+ * SOFTWARE.
+ *
+ * $Id: mthca_srq.c 3047 2005-08-10 03:59:35Z roland $
+ */
+
+#include "mthca_dev.h"
+#include "mthca_cmd.h"
+#include "mthca_memfree.h"
+#include "mthca_wqe.h"
+
+enum {
+ MTHCA_MAX_DIRECT_SRQ_SIZE = 4 * PAGE_SIZE
+};
+
+struct mthca_tavor_srq_context {
+ __be64 wqe_base_ds; /* low 6 bits is descriptor size */
+ __be32 state_pd;
+ __be32 lkey;
+ __be32 uar;
+ __be32 wqe_cnt;
+ u32 reserved[2];
+};
+
+struct mthca_arbel_srq_context {
+ __be32 state_logsize_srqn;
+ __be32 lkey;
+ __be32 db_index;
+ __be32 logstride_usrpage;
+ __be64 wqe_base;
+ __be32 eq_pd;
+ __be16 limit_watermark;
+ __be16 wqe_cnt;
+ u16 reserved1;
+ __be16 wqe_counter;
+ u32 reserved2[3];
+};
+
+static void *get_wqe(struct mthca_srq *srq, int n)
+{
+ if (srq->is_direct)
+ return srq->queue.direct.buf + (n << srq->wqe_shift);
+ else
+ return srq->queue.page_list[(n << srq->wqe_shift) >> PAGE_SHIFT].buf +
+ ((n << srq->wqe_shift) & (PAGE_SIZE - 1));
+}
+
+/*
+ * Return a pointer to the location within a WQE that we're using as a
+ * link when the WQE is in the free list. We use an offset of 4
+ * because in the Tavor case, posting a WQE may overwrite the first
+ * four bytes of the previous WQE. The offset avoids corrupting our
+ * free list if the WQE has already completed and been put on the free
+ * list when we post the next WQE.
+ */
+static inline int *wqe_to_link(void *wqe)
+{
+ return (int *) (wqe + 4);
+}
+
+static void mthca_tavor_init_srq_context(struct mthca_dev *dev,
+ struct mthca_pd *pd,
+ struct mthca_srq *srq,
+ struct mthca_tavor_srq_context *context)
+{
+ memset(context, 0, sizeof *context);
+
+ context->wqe_base_ds = cpu_to_be64(1 << (srq->wqe_shift - 4));
+ context->state_pd = cpu_to_be32(pd->pd_num);
+ context->lkey = cpu_to_be32(srq->mr.ibmr.lkey);
+
+ if (pd->ibpd.uobject)
+ context->uar =
+ cpu_to_be32(to_mucontext(pd->ibpd.uobject->context)->uar.index);
+ else
+ context->uar = cpu_to_be32(dev->driver_uar.index);
+}
+
+static void mthca_arbel_init_srq_context(struct mthca_dev *dev,
+ struct mthca_pd *pd,
+ struct mthca_srq *srq,
+ struct mthca_arbel_srq_context *context)
+{
+ int logsize;
+
+ memset(context, 0, sizeof *context);
+
+ logsize = long_log2(srq->max) + srq->wqe_shift;
+ context->state_logsize_srqn = cpu_to_be32(logsize << 24 | srq->srqn);
+ context->lkey = cpu_to_be32(srq->mr.ibmr.lkey);
+ context->db_index = cpu_to_be32(srq->db_index);
+ context->logstride_usrpage = cpu_to_be32((srq->wqe_shift - 4) << 29);
+ if (pd->ibpd.uobject)
+ context->logstride_usrpage |=
+ cpu_to_be32(to_mucontext(pd->ibpd.uobject->context)->uar.index);
+ else
+ context->logstride_usrpage |= cpu_to_be32(dev->driver_uar.index);
+ context->eq_pd = cpu_to_be32(MTHCA_EQ_ASYNC << 24 | pd->pd_num);
+}
+
+static void mthca_free_srq_buf(struct mthca_dev *dev, struct mthca_srq *srq)
+{
+ mthca_buf_free(dev, srq->max << srq->wqe_shift, &srq->queue,
+ srq->is_direct, &srq->mr);
+ kfree(srq->wrid);
+}
+
+static int mthca_alloc_srq_buf(struct mthca_dev *dev, struct mthca_pd *pd,
+ struct mthca_srq *srq)
+{
+ struct mthca_data_seg *scatter;
+ void *wqe;
+ int err;
+ int i;
+
+ if (pd->ibpd.uobject)
+ return 0;
+
+ srq->wrid = kmalloc(srq->max * sizeof (u64), GFP_KERNEL);
+ if (!srq->wrid)
+ return -ENOMEM;
+
+ err = mthca_buf_alloc(dev, srq->max << srq->wqe_shift,
+ MTHCA_MAX_DIRECT_SRQ_SIZE,
+ &srq->queue, &srq->is_direct, pd, 1, &srq->mr);
+ if (err) {
+ kfree(srq->wrid);
+ return err;
+ }
+
+ /*
+ * Now initialize the SRQ buffer so that all of the WQEs are
+ * linked into the list of free WQEs. In addition, set the
+ * scatter list L_Keys to the sentry value of 0x100.
+ */
+ for (i = 0; i < srq->max; ++i) {
+ wqe = get_wqe(srq, i);
+
+ *wqe_to_link(wqe) = i < srq->max - 1 ? i + 1 : -1;
+
+ for (scatter = wqe + sizeof (struct mthca_next_seg);
+ (void *) scatter < wqe + (1 << srq->wqe_shift);
+ ++scatter)
+ scatter->lkey = cpu_to_be32(MTHCA_INVAL_LKEY);
+ }
+
+ return 0;
+}
+
+int mthca_alloc_srq(struct mthca_dev *dev, struct mthca_pd *pd,
+ struct ib_srq_attr *attr, struct mthca_srq *srq)
+{
+ struct mthca_mailbox *mailbox;
+ u8 status;
+ int ds;
+ int err;
+
+ /* Sanity check SRQ size before proceeding */
+ if (attr->max_wr > 16 << 20 || attr->max_sge > 64)
+ return -EINVAL;
+
+ srq->max = attr->max_wr;
+ srq->max_gs = attr->max_sge;
+ srq->last = NULL;
+ srq->counter = 0;
+
+ if (mthca_is_memfree(dev))
+ srq->max = roundup_pow_of_two(srq->max + 1);
+
+ ds = min(64UL,
+ roundup_pow_of_two(sizeof (struct mthca_next_seg) +
+ srq->max_gs * sizeof (struct mthca_data_seg)));
+ srq->wqe_shift = long_log2(ds);
+
+ srq->srqn = mthca_alloc(&dev->srq_table.alloc);
+ if (srq->srqn == -1)
+ return -ENOMEM;
+
+ if (mthca_is_memfree(dev)) {
+ err = mthca_table_get(dev, dev->srq_table.table, srq->srqn);
+ if (err)
+ goto err_out;
+
+ if (!pd->ibpd.uobject) {
+ srq->db_index = mthca_alloc_db(dev, MTHCA_DB_TYPE_SRQ,
+ srq->srqn, &srq->db);
+ if (srq->db_index < 0) {
+ err = -ENOMEM;
+ goto err_out_icm;
+ }
+ }
+ }
+
+ mailbox = mthca_alloc_mailbox(dev, GFP_KERNEL);
+ if (IS_ERR(mailbox)) {
+ err = PTR_ERR(mailbox);
+ goto err_out_db;
+ }
+
+ err = mthca_alloc_srq_buf(dev, pd, srq);
+ if (err)
+ goto err_out_mailbox;
+
+ spin_lock_init(&srq->lock);
+ atomic_set(&srq->refcount, 1);
+ init_waitqueue_head(&srq->wait);
+
+ if (mthca_is_memfree(dev))
+ mthca_arbel_init_srq_context(dev, pd, srq, mailbox->buf);
+ else
+ mthca_tavor_init_srq_context(dev, pd, srq, mailbox->buf);
+
+ err = mthca_SW2HW_SRQ(dev, mailbox, srq->srqn, &status);
+
+ if (err) {
+ mthca_warn(dev, "SW2HW_SRQ failed (%d)\n", err);
+ goto err_out_free_buf;
+ }
+ if (status) {
+ mthca_warn(dev, "SW2HW_SRQ returned status 0x%02x\n",
+ status);
+ err = -EINVAL;
+ goto err_out_free_buf;
+ }
+
+ spin_lock_irq(&dev->srq_table.lock);
+ if (mthca_array_set(&dev->srq_table.srq,
+ srq->srqn & (dev->limits.num_srqs - 1),
+ srq)) {
+ spin_unlock_irq(&dev->srq_table.lock);
+ goto err_out_free_srq;
+ }
+ spin_unlock_irq(&dev->srq_table.lock);
+
+ mthca_free_mailbox(dev, mailbox);
+
+ srq->first_free = 0;
+ srq->last_free = srq->max - 1;
+
+ return 0;
+
+err_out_free_srq:
+ err = mthca_HW2SW_SRQ(dev, mailbox, srq->srqn, &status);
+ if (err)
+ mthca_warn(dev, "HW2SW_SRQ failed (%d)\n", err);
+ else if (status)
+ mthca_warn(dev, "HW2SW_SRQ returned status 0x%02x\n", status);
+
+err_out_free_buf:
+ if (!pd->ibpd.uobject)
+ mthca_free_srq_buf(dev, srq);
+
+err_out_mailbox:
+ mthca_free_mailbox(dev, mailbox);
+
+err_out_db:
+ if (!pd->ibpd.uobject && mthca_is_memfree(dev))
+ mthca_free_db(dev, MTHCA_DB_TYPE_SRQ, srq->db_index);
+
+err_out_icm:
+ mthca_table_put(dev, dev->srq_table.table, srq->srqn);
+
+err_out:
+ mthca_free(&dev->srq_table.alloc, srq->srqn);
+
+ return err;
+}
+
+void mthca_free_srq(struct mthca_dev *dev, struct mthca_srq *srq)
+{
+ struct mthca_mailbox *mailbox;
+ int err;
+ u8 status;
+
+ mailbox = mthca_alloc_mailbox(dev, GFP_KERNEL);
+ if (IS_ERR(mailbox)) {
+ mthca_warn(dev, "No memory for mailbox to free SRQ.\n");
+ return;
+ }
+
+ err = mthca_HW2SW_SRQ(dev, mailbox, srq->srqn, &status);
+ if (err)
+ mthca_warn(dev, "HW2SW_SRQ failed (%d)\n", err);
+ else if (status)
+ mthca_warn(dev, "HW2SW_SRQ returned status 0x%02x\n", status);
+
+ spin_lock_irq(&dev->srq_table.lock);
+ mthca_array_clear(&dev->srq_table.srq,
+ srq->srqn & (dev->limits.num_srqs - 1));
+ spin_unlock_irq(&dev->srq_table.lock);
+
+ atomic_dec(&srq->refcount);
+ wait_event(srq->wait, !atomic_read(&srq->refcount));
+
+ if (!srq->ibsrq.uobject) {
+ mthca_free_srq_buf(dev, srq);
+ if (mthca_is_memfree(dev))
+ mthca_free_db(dev, MTHCA_DB_TYPE_SRQ, srq->db_index);
+ }
+
+ mthca_table_put(dev, dev->srq_table.table, srq->srqn);
+ mthca_free(&dev->srq_table.alloc, srq->srqn);
+ mthca_free_mailbox(dev, mailbox);
+}
+
+void mthca_srq_event(struct mthca_dev *dev, u32 srqn,
+ enum ib_event_type event_type)
+{
+ struct mthca_srq *srq;
+ struct ib_event event;
+
+ spin_lock(&dev->srq_table.lock);
+ srq = mthca_array_get(&dev->srq_table.srq, srqn & (dev->limits.num_srqs - 1));
+ if (srq)
+ atomic_inc(&srq->refcount);
+ spin_unlock(&dev->srq_table.lock);
+
+ if (!srq) {
+ mthca_warn(dev, "Async event for bogus SRQ %08x\n", srqn);
+ return;
+ }
+
+ if (!srq->ibsrq.event_handler)
+ goto out;
+
+ event.device = &dev->ib_dev;
+ event.event = event_type;
+ event.element.srq = &srq->ibsrq;
+ srq->ibsrq.event_handler(&event, srq->ibsrq.srq_context);
+
+out:
+ if (atomic_dec_and_test(&srq->refcount))
+ wake_up(&srq->wait);
+}
+
+/*
+ * This function must be called with IRQs disabled.
+ */
+void mthca_free_srq_wqe(struct mthca_srq *srq, u32 wqe_addr)
+{
+ int ind;
+
+ ind = wqe_addr >> srq->wqe_shift;
+
+ spin_lock(&srq->lock);
+
+ if (likely(srq->first_free >= 0))
+ *wqe_to_link(get_wqe(srq, srq->last_free)) = ind;
+ else
+ srq->first_free = ind;
+
+ *wqe_to_link(get_wqe(srq, ind)) = -1;
+ srq->last_free = ind;
+
+ spin_unlock(&srq->lock);
+}
+
+int mthca_tavor_post_srq_recv(struct ib_srq *ibsrq, struct ib_recv_wr *wr,
+ struct ib_recv_wr **bad_wr)
+{
+ struct mthca_dev *dev = to_mdev(ibsrq->device);
+ struct mthca_srq *srq = to_msrq(ibsrq);
+ unsigned long flags;
+ int err = 0;
+ int first_ind;
+ int ind;
+ int next_ind;
+ int nreq;
+ int i;
+ void *wqe;
+ void *prev_wqe;
+
+ spin_lock_irqsave(&srq->lock, flags);
+
+ first_ind = srq->first_free;
+
+ for (nreq = 0; wr; ++nreq, wr = wr->next) {
+ ind = srq->first_free;
+
+ if (ind < 0) {
+ mthca_err(dev, "SRQ %06x full\n", srq->srqn);
+ err = -ENOMEM;
+ *bad_wr = wr;
+ return nreq;
+ }
+
+ wqe = get_wqe(srq, ind);
+ next_ind = *wqe_to_link(wqe);
+ prev_wqe = srq->last;
+ srq->last = wqe;
+
+ ((struct mthca_next_seg *) wqe)->nda_op = 0;
+ ((struct mthca_next_seg *) wqe)->ee_nds = 0;
+ /* flags field will always remain 0 */
+
+ wqe += sizeof (struct mthca_next_seg);
+
+ if (unlikely(wr->num_sge > srq->max_gs)) {
+ err = -EINVAL;
+ *bad_wr = wr;
+ srq->last = prev_wqe;
+ return nreq;
+ }
+
+ for (i = 0; i < wr->num_sge; ++i) {
+ ((struct mthca_data_seg *) wqe)->byte_count =
+ cpu_to_be32(wr->sg_list[i].length);
+ ((struct mthca_data_seg *) wqe)->lkey =
+ cpu_to_be32(wr->sg_list[i].lkey);
+ ((struct mthca_data_seg *) wqe)->addr =
+ cpu_to_be64(wr->sg_list[i].addr);
+ wqe += sizeof (struct mthca_data_seg);
+ }
+
+ if (i < srq->max_gs) {
+ ((struct mthca_data_seg *) wqe)->byte_count = 0;
+ ((struct mthca_data_seg *) wqe)->lkey = cpu_to_be32(MTHCA_INVAL_LKEY);
+ ((struct mthca_data_seg *) wqe)->addr = 0;
+ }
+
+ if (likely(prev_wqe)) {
+ ((struct mthca_next_seg *) prev_wqe)->nda_op =
+ cpu_to_be32((ind << srq->wqe_shift) | 1);
+ wmb();
+ ((struct mthca_next_seg *) prev_wqe)->ee_nds =
+ cpu_to_be32(MTHCA_NEXT_DBD);
+ }
+
+ srq->wrid[ind] = wr->wr_id;
+ srq->first_free = next_ind;
+ }
+
+ return nreq;
+
+ if (likely(nreq)) {
+ __be32 doorbell[2];
+
+ doorbell[0] = cpu_to_be32(first_ind << srq->wqe_shift);
+ doorbell[1] = cpu_to_be32((srq->srqn << 8) | nreq);
+
+ /*
+ * Make sure that descriptors are written before
+ * doorbell is rung.
+ */
+ wmb();
+
+ mthca_write64(doorbell,
+ dev->kar + MTHCA_RECEIVE_DOORBELL,
+ MTHCA_GET_DOORBELL_LOCK(&dev->doorbell_lock));
+ }
+
+ spin_unlock_irqrestore(&srq->lock, flags);
+ return err;
+}
+
+int mthca_arbel_post_srq_recv(struct ib_srq *ibsrq, struct ib_recv_wr *wr,
+ struct ib_recv_wr **bad_wr)
+{
+ struct mthca_dev *dev = to_mdev(ibsrq->device);
+ struct mthca_srq *srq = to_msrq(ibsrq);
+ unsigned long flags;
+ int err = 0;
+ int ind;
+ int next_ind;
+ int nreq;
+ int i;
+ void *wqe;
+
+ spin_lock_irqsave(&srq->lock, flags);
+
+ for (nreq = 0; wr; ++nreq, wr = wr->next) {
+ ind = srq->first_free;
+
+ if (ind < 0) {
+ mthca_err(dev, "SRQ %06x full\n", srq->srqn);
+ err = -ENOMEM;
+ *bad_wr = wr;
+ return nreq;
+ }
+
+ wqe = get_wqe(srq, ind);
+ next_ind = *wqe_to_link(wqe);
+
+ ((struct mthca_next_seg *) wqe)->nda_op =
+ cpu_to_be32((next_ind << srq->wqe_shift) | 1);
+ ((struct mthca_next_seg *) wqe)->ee_nds = 0;
+ /* flags field will always remain 0 */
+
+ wqe += sizeof (struct mthca_next_seg);
+
+ if (unlikely(wr->num_sge > srq->max_gs)) {
+ err = -EINVAL;
+ *bad_wr = wr;
+ return nreq;
+ }
+
+ for (i = 0; i < wr->num_sge; ++i) {
+ ((struct mthca_data_seg *) wqe)->byte_count =
+ cpu_to_be32(wr->sg_list[i].length);
+ ((struct mthca_data_seg *) wqe)->lkey =
+ cpu_to_be32(wr->sg_list[i].lkey);
+ ((struct mthca_data_seg *) wqe)->addr =
+ cpu_to_be64(wr->sg_list[i].addr);
+ wqe += sizeof (struct mthca_data_seg);
+ }
+
+ if (i < srq->max_gs) {
+ ((struct mthca_data_seg *) wqe)->byte_count = 0;
+ ((struct mthca_data_seg *) wqe)->lkey = cpu_to_be32(MTHCA_INVAL_LKEY);
+ ((struct mthca_data_seg *) wqe)->addr = 0;
+ }
+
+ srq->wrid[ind] = wr->wr_id;
+ srq->first_free = next_ind;
+ }
+
+ if (likely(nreq)) {
+ srq->counter += nreq;
+
+ /*
+ * Make sure that descriptors are written before
+ * we write doorbell record.
+ */
+ wmb();
+ *srq->db = cpu_to_be32(srq->counter);
+ }
+
+ spin_unlock_irqrestore(&srq->lock, flags);
+ return err;
+}
+
+int __devinit mthca_init_srq_table(struct mthca_dev *dev)
+{
+ int err;
+
+ if (!(dev->mthca_flags & MTHCA_FLAG_SRQ))
+ return 0;
+
+ spin_lock_init(&dev->srq_table.lock);
+
+ err = mthca_alloc_init(&dev->srq_table.alloc,
+ dev->limits.num_srqs,
+ dev->limits.num_srqs - 1,
+ dev->limits.reserved_srqs);
+ if (err)
+ return err;
+
+ err = mthca_array_init(&dev->srq_table.srq,
+ dev->limits.num_srqs);
+ if (err)
+ mthca_alloc_cleanup(&dev->srq_table.alloc);
+
+ return err;
+}
+
+void __devexit mthca_cleanup_srq_table(struct mthca_dev *dev)
+{
+ if (!(dev->mthca_flags & MTHCA_FLAG_SRQ))
+ return;
+
+ mthca_array_cleanup(&dev->srq_table.srq, dev->limits.num_srqs);
+ mthca_alloc_cleanup(&dev->srq_table.alloc);
+}
diff --git a/drivers/infiniband/hw/mthca/mthca_user.h b/drivers/infiniband/hw/mthca/mthca_user.h
index 3024c1b..41613ec 100644
--- a/drivers/infiniband/hw/mthca/mthca_user.h
+++ b/drivers/infiniband/hw/mthca/mthca_user.h
@@ -69,6 +69,17 @@
__u32 reserved;
};
+struct mthca_create_srq {
+ __u32 lkey;
+ __u32 db_index;
+ __u64 db_page;
+};
+
+struct mthca_create_srq_resp {
+ __u32 srqn;
+ __u32 reserved;
+};
+
struct mthca_create_qp {
__u32 lkey;
__u32 reserved;
diff --git a/drivers/infiniband/hw/mthca/mthca_wqe.h b/drivers/infiniband/hw/mthca/mthca_wqe.h
new file mode 100644
index 0000000..1f4c0ff
--- /dev/null
+++ b/drivers/infiniband/hw/mthca/mthca_wqe.h
@@ -0,0 +1,114 @@
+/*
+ * Copyright (c) 2005 Cisco Systems. All rights reserved.
+ *
+ * This software is available to you under a choice of one of two
+ * licenses. You may choose to be licensed under the terms of the GNU
+ * General Public License (GPL) Version 2, available from the file
+ * COPYING in the main directory of this source tree, or the
+ * OpenIB.org BSD license below:
+ *
+ * Redistribution and use in source and binary forms, with or
+ * without modification, are permitted provided that the following
+ * conditions are met:
+ *
+ * - Redistributions of source code must retain the above
+ * copyright notice, this list of conditions and the following
+ * disclaimer.
+ *
+ * - Redistributions in binary form must reproduce the above
+ * copyright notice, this list of conditions and the following
+ * disclaimer in the documentation and/or other materials
+ * provided with the distribution.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
+ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS
+ * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN
+ * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
+ * SOFTWARE.
+ *
+ * $Id: mthca_wqe.h 3047 2005-08-10 03:59:35Z roland $
+ */
+
+#ifndef MTHCA_WQE_H
+#define MTHCA_WQE_H
+
+#include <linux/types.h>
+
+enum {
+ MTHCA_NEXT_DBD = 1 << 7,
+ MTHCA_NEXT_FENCE = 1 << 6,
+ MTHCA_NEXT_CQ_UPDATE = 1 << 3,
+ MTHCA_NEXT_EVENT_GEN = 1 << 2,
+ MTHCA_NEXT_SOLICIT = 1 << 1,
+
+ MTHCA_MLX_VL15 = 1 << 17,
+ MTHCA_MLX_SLR = 1 << 16
+};
+
+enum {
+ MTHCA_INVAL_LKEY = 0x100
+};
+
+struct mthca_next_seg {
+ __be32 nda_op; /* [31:6] next WQE [4:0] next opcode */
+ __be32 ee_nds; /* [31:8] next EE [7] DBD [6] F [5:0] next WQE size */
+ __be32 flags; /* [3] CQ [2] Event [1] Solicit */
+ __be32 imm; /* immediate data */
+};
+
+struct mthca_tavor_ud_seg {
+ u32 reserved1;
+ __be32 lkey;
+ __be64 av_addr;
+ u32 reserved2[4];
+ __be32 dqpn;
+ __be32 qkey;
+ u32 reserved3[2];
+};
+
+struct mthca_arbel_ud_seg {
+ __be32 av[8];
+ __be32 dqpn;
+ __be32 qkey;
+ u32 reserved[2];
+};
+
+struct mthca_bind_seg {
+ __be32 flags; /* [31] Atomic [30] rem write [29] rem read */
+ u32 reserved;
+ __be32 new_rkey;
+ __be32 lkey;
+ __be64 addr;
+ __be64 length;
+};
+
+struct mthca_raddr_seg {
+ __be64 raddr;
+ __be32 rkey;
+ u32 reserved;
+};
+
+struct mthca_atomic_seg {
+ __be64 swap_add;
+ __be64 compare;
+};
+
+struct mthca_data_seg {
+ __be32 byte_count;
+ __be32 lkey;
+ __be64 addr;
+};
+
+struct mthca_mlx_seg {
+ __be32 nda_op;
+ __be32 nds;
+ __be32 flags; /* [17] VL15 [16] SLR [14:12] static rate
+ [11:8] SL [3] C [2] E */
+ __be16 rlid;
+ __be16 vcrc;
+};
+
+#endif /* MTHCA_WQE_H */
diff --git a/drivers/infiniband/ulp/ipoib/Makefile b/drivers/infiniband/ulp/ipoib/Makefile
index 394bc08..8935e74 100644
--- a/drivers/infiniband/ulp/ipoib/Makefile
+++ b/drivers/infiniband/ulp/ipoib/Makefile
@@ -1,5 +1,3 @@
-EXTRA_CFLAGS += -Idrivers/infiniband/include
-
obj-$(CONFIG_INFINIBAND_IPOIB) += ib_ipoib.o
ib_ipoib-y := ipoib_main.o \
diff --git a/drivers/infiniband/ulp/ipoib/ipoib.h b/drivers/infiniband/ulp/ipoib/ipoib.h
index 04c98f5..bea960b 100644
--- a/drivers/infiniband/ulp/ipoib/ipoib.h
+++ b/drivers/infiniband/ulp/ipoib/ipoib.h
@@ -1,5 +1,7 @@
/*
* Copyright (c) 2004, 2005 Topspin Communications. All rights reserved.
+ * Copyright (c) 2005 Sun Microsystems, Inc. All rights reserved.
+ * Copyright (c) 2004 Voltaire, Inc. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
@@ -49,9 +51,9 @@
#include <asm/atomic.h>
#include <asm/semaphore.h>
-#include <ib_verbs.h>
-#include <ib_pack.h>
-#include <ib_sa.h>
+#include <rdma/ib_verbs.h>
+#include <rdma/ib_pack.h>
+#include <rdma/ib_sa.h>
/* constants */
@@ -88,8 +90,8 @@
/* structs */
struct ipoib_header {
- u16 proto;
- u16 reserved;
+ __be16 proto;
+ u16 reserved;
};
struct ipoib_pseudoheader {
diff --git a/drivers/infiniband/ulp/ipoib/ipoib_fs.c b/drivers/infiniband/ulp/ipoib/ipoib_fs.c
index a84e5fe..38b150f 100644
--- a/drivers/infiniband/ulp/ipoib/ipoib_fs.c
+++ b/drivers/infiniband/ulp/ipoib/ipoib_fs.c
@@ -97,7 +97,7 @@
for (n = 0, i = 0; i < sizeof mgid / 2; ++i) {
n += sprintf(gid_buf + n, "%x",
- be16_to_cpu(((u16 *)mgid.raw)[i]));
+ be16_to_cpu(((__be16 *) mgid.raw)[i]));
if (i < sizeof mgid / 2 - 1)
gid_buf[n++] = ':';
}
diff --git a/drivers/infiniband/ulp/ipoib/ipoib_ib.c b/drivers/infiniband/ulp/ipoib/ipoib_ib.c
index eee8236..ef0e389 100644
--- a/drivers/infiniband/ulp/ipoib/ipoib_ib.c
+++ b/drivers/infiniband/ulp/ipoib/ipoib_ib.c
@@ -1,5 +1,8 @@
/*
* Copyright (c) 2004, 2005 Topspin Communications. All rights reserved.
+ * Copyright (c) 2005 Sun Microsystems, Inc. All rights reserved.
+ * Copyright (c) 2005 Mellanox Technologies. All rights reserved.
+ * Copyright (c) 2004, 2005 Voltaire, Inc. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
@@ -35,7 +38,7 @@
#include <linux/delay.h>
#include <linux/dma-mapping.h>
-#include <ib_cache.h>
+#include <rdma/ib_cache.h>
#include "ipoib.h"
diff --git a/drivers/infiniband/ulp/ipoib/ipoib_main.c b/drivers/infiniband/ulp/ipoib/ipoib_main.c
index fa00816..0e8ac13 100644
--- a/drivers/infiniband/ulp/ipoib/ipoib_main.c
+++ b/drivers/infiniband/ulp/ipoib/ipoib_main.c
@@ -1,5 +1,7 @@
/*
* Copyright (c) 2004 Topspin Communications. All rights reserved.
+ * Copyright (c) 2005 Sun Microsystems, Inc. All rights reserved.
+ * Copyright (c) 2004 Voltaire, Inc. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
@@ -34,7 +36,6 @@
#include "ipoib.h"
-#include <linux/version.h>
#include <linux/module.h>
#include <linux/init.h>
@@ -607,8 +608,8 @@
ipoib_warn(priv, "Unicast, no %s: type %04x, QPN %06x "
IPOIB_GID_FMT "\n",
skb->dst ? "neigh" : "dst",
- be16_to_cpup((u16 *) skb->data),
- be32_to_cpup((u32 *) phdr->hwaddr),
+ be16_to_cpup((__be16 *) skb->data),
+ be32_to_cpup((__be32 *) phdr->hwaddr),
IPOIB_GID_ARG(*(union ib_gid *) (phdr->hwaddr + 4)));
dev_kfree_skb_any(skb);
++priv->stats.tx_dropped;
@@ -671,7 +672,7 @@
{
struct ipoib_dev_priv *priv = netdev_priv(dev);
- schedule_work(&priv->restart_task);
+ queue_work(ipoib_workqueue, &priv->restart_task);
}
static void ipoib_neigh_destructor(struct neighbour *n)
@@ -780,15 +781,11 @@
ipoib_ib_dev_cleanup(dev);
- if (priv->rx_ring) {
- kfree(priv->rx_ring);
- priv->rx_ring = NULL;
- }
+ kfree(priv->rx_ring);
+ kfree(priv->tx_ring);
- if (priv->tx_ring) {
- kfree(priv->tx_ring);
- priv->tx_ring = NULL;
- }
+ priv->rx_ring = NULL;
+ priv->tx_ring = NULL;
}
static void ipoib_setup(struct net_device *dev)
@@ -886,6 +883,12 @@
if (pkey < 0 || pkey > 0xffff)
return -EINVAL;
+ /*
+ * Set the full membership bit, so that we join the right
+ * broadcast group, etc.
+ */
+ pkey |= 0x8000;
+
ret = ipoib_vlan_add(container_of(cdev, struct net_device, class_dev),
pkey);
@@ -938,6 +941,12 @@
goto alloc_mem_failed;
}
+ /*
+ * Set the full membership bit, so that we join the right
+ * broadcast group, etc.
+ */
+ priv->pkey |= 0x8000;
+
priv->dev->broadcast[8] = priv->pkey >> 8;
priv->dev->broadcast[9] = priv->pkey & 0xff;
diff --git a/drivers/infiniband/ulp/ipoib/ipoib_multicast.c b/drivers/infiniband/ulp/ipoib/ipoib_multicast.c
index 70208c3..aca7aea 100644
--- a/drivers/infiniband/ulp/ipoib/ipoib_multicast.c
+++ b/drivers/infiniband/ulp/ipoib/ipoib_multicast.c
@@ -1,5 +1,7 @@
/*
* Copyright (c) 2004, 2005 Topspin Communications. All rights reserved.
+ * Copyright (c) 2005 Sun Microsystems, Inc. All rights reserved.
+ * Copyright (c) 2004 Voltaire, Inc. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
@@ -357,7 +359,7 @@
rec.mgid = mcast->mcmember.mgid;
rec.port_gid = priv->local_gid;
- rec.pkey = be16_to_cpu(priv->pkey);
+ rec.pkey = cpu_to_be16(priv->pkey);
ret = ib_sa_mcmember_rec_set(priv->ca, priv->port, &rec,
IB_SA_MCMEMBER_REC_MGID |
@@ -457,7 +459,7 @@
rec.mgid = mcast->mcmember.mgid;
rec.port_gid = priv->local_gid;
- rec.pkey = be16_to_cpu(priv->pkey);
+ rec.pkey = cpu_to_be16(priv->pkey);
comp_mask =
IB_SA_MCMEMBER_REC_MGID |
@@ -646,7 +648,7 @@
rec.mgid = mcast->mcmember.mgid;
rec.port_gid = priv->local_gid;
- rec.pkey = be16_to_cpu(priv->pkey);
+ rec.pkey = cpu_to_be16(priv->pkey);
/* Remove ourselves from the multicast group */
ret = ipoib_mcast_detach(dev, be16_to_cpu(mcast->mcmember.mlid),
diff --git a/drivers/infiniband/ulp/ipoib/ipoib_verbs.c b/drivers/infiniband/ulp/ipoib/ipoib_verbs.c
index 4933edf..79f59d0 100644
--- a/drivers/infiniband/ulp/ipoib/ipoib_verbs.c
+++ b/drivers/infiniband/ulp/ipoib/ipoib_verbs.c
@@ -1,5 +1,6 @@
/*
* Copyright (c) 2004, 2005 Topspin Communications. All rights reserved.
+ * Copyright (c) 2005 Mellanox Technologies. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
@@ -32,7 +33,7 @@
* $Id: ipoib_verbs.c 1349 2004-12-16 21:09:43Z roland $
*/
-#include <ib_cache.h>
+#include <rdma/ib_cache.h>
#include "ipoib.h"
diff --git a/drivers/infiniband/ulp/ipoib/ipoib_vlan.c b/drivers/infiniband/ulp/ipoib/ipoib_vlan.c
index 94b8ea8..332d730 100644
--- a/drivers/infiniband/ulp/ipoib/ipoib_vlan.c
+++ b/drivers/infiniband/ulp/ipoib/ipoib_vlan.c
@@ -32,7 +32,6 @@
* $Id: ipoib_vlan.c 1349 2004-12-16 21:09:43Z roland $
*/
-#include <linux/version.h>
#include <linux/module.h>
#include <linux/init.h>
diff --git a/drivers/isdn/capi/capifs.c b/drivers/isdn/capi/capifs.c
index f8570fd..3abd7fc 100644
--- a/drivers/isdn/capi/capifs.c
+++ b/drivers/isdn/capi/capifs.c
@@ -191,8 +191,10 @@
err = register_filesystem(&capifs_fs_type);
if (!err) {
capifs_mnt = kern_mount(&capifs_fs_type);
- if (IS_ERR(capifs_mnt))
+ if (IS_ERR(capifs_mnt)) {
err = PTR_ERR(capifs_mnt);
+ unregister_filesystem(&capifs_fs_type);
+ }
}
if (!err)
printk(KERN_NOTICE "capifs: Rev %s\n", rev);
diff --git a/drivers/md/md.c b/drivers/md/md.c
index 486ee50..20ca80b 100644
--- a/drivers/md/md.c
+++ b/drivers/md/md.c
@@ -1689,6 +1689,7 @@
mddev->pers = pers[pnum];
spin_unlock(&pers_lock);
+ mddev->recovery = 0;
mddev->resync_max_sectors = mddev->size << 1; /* may be over-ridden by personality */
/* before we start the array running, initialise the bitmap */
@@ -4011,3 +4012,4 @@
EXPORT_SYMBOL(md_check_recovery);
MODULE_LICENSE("GPL");
MODULE_ALIAS("md");
+MODULE_ALIAS_BLOCKDEV_MAJOR(MD_MAJOR);
diff --git a/drivers/media/dvb/dvb-usb/dibusb-common.c b/drivers/media/dvb/dvb-usb/dibusb-common.c
index 63b626f..9b9d6f8 100644
--- a/drivers/media/dvb/dvb-usb/dibusb-common.c
+++ b/drivers/media/dvb/dvb-usb/dibusb-common.c
@@ -70,13 +70,22 @@
int dibusb2_0_streaming_ctrl(struct dvb_usb_device *d, int onoff)
{
- u8 b[2];
+ u8 b[3] = { 0 };
+ int ret;
+
+ if ((ret = dibusb_streaming_ctrl(d,onoff)) < 0)
+ return ret;
+
+ if (onoff) {
+ b[0] = DIBUSB_REQ_SET_STREAMING_MODE;
+ b[1] = 0x00;
+ if ((ret = dvb_usb_generic_write(d,b,2)) < 0)
+ return ret;
+ }
+
b[0] = DIBUSB_REQ_SET_IOCTL;
b[1] = onoff ? DIBUSB_IOCTL_CMD_ENABLE_STREAM : DIBUSB_IOCTL_CMD_DISABLE_STREAM;
-
- dvb_usb_generic_write(d,b,3);
-
- return dibusb_streaming_ctrl(d,onoff);
+ return dvb_usb_generic_write(d,b,3);
}
EXPORT_SYMBOL(dibusb2_0_streaming_ctrl);
diff --git a/drivers/media/dvb/dvb-usb/dvb-usb-dvb.c b/drivers/media/dvb/dvb-usb/dvb-usb-dvb.c
index 3491ff4..6fa9210 100644
--- a/drivers/media/dvb/dvb-usb/dvb-usb-dvb.c
+++ b/drivers/media/dvb/dvb-usb/dvb-usb-dvb.c
@@ -23,12 +23,12 @@
*/
if (newfeedcount == 0) {
deb_ts("stop feeding\n");
+ dvb_usb_urb_kill(d);
if (d->props.streaming_ctrl != NULL)
if ((ret = d->props.streaming_ctrl(d,0)))
err("error while stopping stream.");
- dvb_usb_urb_kill(d);
}
d->feedcount = newfeedcount;
@@ -44,6 +44,8 @@
* for reception.
*/
if (d->feedcount == onoff && d->feedcount > 0) {
+ deb_ts("submitting all URBs\n");
+ dvb_usb_urb_submit(d);
deb_ts("controlling pid parser\n");
if (d->props.caps & DVB_USB_HAS_PID_FILTER &&
@@ -59,7 +61,6 @@
return -ENODEV;
}
- dvb_usb_urb_submit(d);
}
return 0;
}
diff --git a/drivers/media/dvb/frontends/tda80xx.c b/drivers/media/dvb/frontends/tda80xx.c
index 88e1250..d1cabb6 100644
--- a/drivers/media/dvb/frontends/tda80xx.c
+++ b/drivers/media/dvb/frontends/tda80xx.c
@@ -30,6 +30,7 @@
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/slab.h>
+#include <asm/irq.h>
#include <asm/div64.h>
#include "dvb_frontend.h"
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
new file mode 100644
index 0000000..1588a59
--- /dev/null
+++ b/drivers/mfd/Kconfig
@@ -0,0 +1,16 @@
+#
+# Multifunction miscellaneous devices
+#
+
+menu "Multimedia Capabilities Port drivers"
+
+config MCP
+ tristate
+
+# Interface drivers
+config MCP_SA11X0
+ tristate "Support SA11x0 MCP interface"
+ depends on ARCH_SA1100
+ select MCP
+
+endmenu
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
new file mode 100644
index 0000000..98bdd6a
--- /dev/null
+++ b/drivers/mfd/Makefile
@@ -0,0 +1,6 @@
+#
+# Makefile for multifunction miscellaneous devices
+#
+
+obj-$(CONFIG_MCP) += mcp-core.o
+obj-$(CONFIG_MCP_SA11X0) += mcp-sa11x0.o
diff --git a/drivers/mfd/mcp-core.c b/drivers/mfd/mcp-core.c
new file mode 100644
index 0000000..c75d713
--- /dev/null
+++ b/drivers/mfd/mcp-core.c
@@ -0,0 +1,255 @@
+/*
+ * linux/drivers/mfd/mcp-core.c
+ *
+ * Copyright (C) 2001 Russell King
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License.
+ *
+ * Generic MCP (Multimedia Communications Port) layer. All MCP locking
+ * is solely held within this file.
+ */
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/errno.h>
+#include <linux/smp.h>
+#include <linux/device.h>
+
+#include <asm/dma.h>
+#include <asm/system.h>
+
+#include "mcp.h"
+
+#define to_mcp(d) container_of(d, struct mcp, attached_device)
+#define to_mcp_driver(d) container_of(d, struct mcp_driver, drv)
+
+static int mcp_bus_match(struct device *dev, struct device_driver *drv)
+{
+ return 1;
+}
+
+static int mcp_bus_probe(struct device *dev)
+{
+ struct mcp *mcp = to_mcp(dev);
+ struct mcp_driver *drv = to_mcp_driver(dev->driver);
+
+ return drv->probe(mcp);
+}
+
+static int mcp_bus_remove(struct device *dev)
+{
+ struct mcp *mcp = to_mcp(dev);
+ struct mcp_driver *drv = to_mcp_driver(dev->driver);
+
+ drv->remove(mcp);
+ return 0;
+}
+
+static int mcp_bus_suspend(struct device *dev, pm_message_t state)
+{
+ struct mcp *mcp = to_mcp(dev);
+ int ret = 0;
+
+ if (dev->driver) {
+ struct mcp_driver *drv = to_mcp_driver(dev->driver);
+
+ ret = drv->suspend(mcp, state);
+ }
+ return ret;
+}
+
+static int mcp_bus_resume(struct device *dev)
+{
+ struct mcp *mcp = to_mcp(dev);
+ int ret = 0;
+
+ if (dev->driver) {
+ struct mcp_driver *drv = to_mcp_driver(dev->driver);
+
+ ret = drv->resume(mcp);
+ }
+ return ret;
+}
+
+static struct bus_type mcp_bus_type = {
+ .name = "mcp",
+ .match = mcp_bus_match,
+ .suspend = mcp_bus_suspend,
+ .resume = mcp_bus_resume,
+};
+
+/**
+ * mcp_set_telecom_divisor - set the telecom divisor
+ * @mcp: MCP interface structure
+ * @div: SIB clock divisor
+ *
+ * Set the telecom divisor on the MCP interface. The resulting
+ * sample rate is SIBCLOCK/div.
+ */
+void mcp_set_telecom_divisor(struct mcp *mcp, unsigned int div)
+{
+ spin_lock_irq(&mcp->lock);
+ mcp->ops->set_telecom_divisor(mcp, div);
+ spin_unlock_irq(&mcp->lock);
+}
+EXPORT_SYMBOL(mcp_set_telecom_divisor);
+
+/**
+ * mcp_set_audio_divisor - set the audio divisor
+ * @mcp: MCP interface structure
+ * @div: SIB clock divisor
+ *
+ * Set the audio divisor on the MCP interface.
+ */
+void mcp_set_audio_divisor(struct mcp *mcp, unsigned int div)
+{
+ spin_lock_irq(&mcp->lock);
+ mcp->ops->set_audio_divisor(mcp, div);
+ spin_unlock_irq(&mcp->lock);
+}
+EXPORT_SYMBOL(mcp_set_audio_divisor);
+
+/**
+ * mcp_reg_write - write a device register
+ * @mcp: MCP interface structure
+ * @reg: 4-bit register index
+ * @val: 16-bit data value
+ *
+ * Write a device register. The MCP interface must be enabled
+ * to prevent this function hanging.
+ */
+void mcp_reg_write(struct mcp *mcp, unsigned int reg, unsigned int val)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&mcp->lock, flags);
+ mcp->ops->reg_write(mcp, reg, val);
+ spin_unlock_irqrestore(&mcp->lock, flags);
+}
+EXPORT_SYMBOL(mcp_reg_write);
+
+/**
+ * mcp_reg_read - read a device register
+ * @mcp: MCP interface structure
+ * @reg: 4-bit register index
+ *
+ * Read a device register and return its value. The MCP interface
+ * must be enabled to prevent this function hanging.
+ */
+unsigned int mcp_reg_read(struct mcp *mcp, unsigned int reg)
+{
+ unsigned long flags;
+ unsigned int val;
+
+ spin_lock_irqsave(&mcp->lock, flags);
+ val = mcp->ops->reg_read(mcp, reg);
+ spin_unlock_irqrestore(&mcp->lock, flags);
+
+ return val;
+}
+EXPORT_SYMBOL(mcp_reg_read);
+
+/**
+ * mcp_enable - enable the MCP interface
+ * @mcp: MCP interface to enable
+ *
+ * Enable the MCP interface. Each call to mcp_enable will need
+ * a corresponding call to mcp_disable to disable the interface.
+ */
+void mcp_enable(struct mcp *mcp)
+{
+ spin_lock_irq(&mcp->lock);
+ if (mcp->use_count++ == 0)
+ mcp->ops->enable(mcp);
+ spin_unlock_irq(&mcp->lock);
+}
+EXPORT_SYMBOL(mcp_enable);
+
+/**
+ * mcp_disable - disable the MCP interface
+ * @mcp: MCP interface to disable
+ *
+ * Disable the MCP interface. The MCP interface will only be
+ * disabled once the number of calls to mcp_enable matches the
+ * number of calls to mcp_disable.
+ */
+void mcp_disable(struct mcp *mcp)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&mcp->lock, flags);
+ if (--mcp->use_count == 0)
+ mcp->ops->disable(mcp);
+ spin_unlock_irqrestore(&mcp->lock, flags);
+}
+EXPORT_SYMBOL(mcp_disable);
+
+static void mcp_release(struct device *dev)
+{
+ struct mcp *mcp = container_of(dev, struct mcp, attached_device);
+
+ kfree(mcp);
+}
+
+struct mcp *mcp_host_alloc(struct device *parent, size_t size)
+{
+ struct mcp *mcp;
+
+ mcp = kmalloc(sizeof(struct mcp) + size, GFP_KERNEL);
+ if (mcp) {
+ memset(mcp, 0, sizeof(struct mcp) + size);
+ spin_lock_init(&mcp->lock);
+ mcp->attached_device.parent = parent;
+ mcp->attached_device.bus = &mcp_bus_type;
+ mcp->attached_device.dma_mask = parent->dma_mask;
+ mcp->attached_device.release = mcp_release;
+ }
+ return mcp;
+}
+EXPORT_SYMBOL(mcp_host_alloc);
+
+int mcp_host_register(struct mcp *mcp)
+{
+ strcpy(mcp->attached_device.bus_id, "mcp0");
+ return device_register(&mcp->attached_device);
+}
+EXPORT_SYMBOL(mcp_host_register);
+
+void mcp_host_unregister(struct mcp *mcp)
+{
+ device_unregister(&mcp->attached_device);
+}
+EXPORT_SYMBOL(mcp_host_unregister);
+
+int mcp_driver_register(struct mcp_driver *mcpdrv)
+{
+ mcpdrv->drv.bus = &mcp_bus_type;
+ mcpdrv->drv.probe = mcp_bus_probe;
+ mcpdrv->drv.remove = mcp_bus_remove;
+ return driver_register(&mcpdrv->drv);
+}
+EXPORT_SYMBOL(mcp_driver_register);
+
+void mcp_driver_unregister(struct mcp_driver *mcpdrv)
+{
+ driver_unregister(&mcpdrv->drv);
+}
+EXPORT_SYMBOL(mcp_driver_unregister);
+
+static int __init mcp_init(void)
+{
+ return bus_register(&mcp_bus_type);
+}
+
+static void __exit mcp_exit(void)
+{
+ bus_unregister(&mcp_bus_type);
+}
+
+module_init(mcp_init);
+module_exit(mcp_exit);
+
+MODULE_AUTHOR("Russell King <rmk@arm.linux.org.uk>");
+MODULE_DESCRIPTION("Core multimedia communications port driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/mfd/mcp-sa11x0.c b/drivers/mfd/mcp-sa11x0.c
new file mode 100644
index 0000000..e9806fb
--- /dev/null
+++ b/drivers/mfd/mcp-sa11x0.c
@@ -0,0 +1,275 @@
+/*
+ * linux/drivers/mfd/mcp-sa11x0.c
+ *
+ * Copyright (C) 2001-2005 Russell King
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License.
+ *
+ * SA11x0 MCP (Multimedia Communications Port) driver.
+ *
+ * MCP read/write timeouts from Jordi Colomer, rehacked by rmk.
+ */
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/errno.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/spinlock.h>
+#include <linux/slab.h>
+#include <linux/device.h>
+
+#include <asm/dma.h>
+#include <asm/hardware.h>
+#include <asm/mach-types.h>
+#include <asm/system.h>
+#include <asm/arch/mcp.h>
+
+#include <asm/arch/assabet.h>
+
+#include "mcp.h"
+
+struct mcp_sa11x0 {
+ u32 mccr0;
+ u32 mccr1;
+};
+
+#define priv(mcp) ((struct mcp_sa11x0 *)mcp_priv(mcp))
+
+static void
+mcp_sa11x0_set_telecom_divisor(struct mcp *mcp, unsigned int divisor)
+{
+ unsigned int mccr0;
+
+ divisor /= 32;
+
+ mccr0 = Ser4MCCR0 & ~0x00007f00;
+ mccr0 |= divisor << 8;
+ Ser4MCCR0 = mccr0;
+}
+
+static void
+mcp_sa11x0_set_audio_divisor(struct mcp *mcp, unsigned int divisor)
+{
+ unsigned int mccr0;
+
+ divisor /= 32;
+
+ mccr0 = Ser4MCCR0 & ~0x0000007f;
+ mccr0 |= divisor;
+ Ser4MCCR0 = mccr0;
+}
+
+/*
+ * Write data to the device. The bit should be set after 3 subframe
+ * times (each frame is 64 clocks). We wait a maximum of 6 subframes.
+ * We really should try doing something more productive while we
+ * wait.
+ */
+static void
+mcp_sa11x0_write(struct mcp *mcp, unsigned int reg, unsigned int val)
+{
+ int ret = -ETIME;
+ int i;
+
+ Ser4MCDR2 = reg << 17 | MCDR2_Wr | (val & 0xffff);
+
+ for (i = 0; i < 2; i++) {
+ udelay(mcp->rw_timeout);
+ if (Ser4MCSR & MCSR_CWC) {
+ ret = 0;
+ break;
+ }
+ }
+
+ if (ret < 0)
+ printk(KERN_WARNING "mcp: write timed out\n");
+}
+
+/*
+ * Read data from the device. The bit should be set after 3 subframe
+ * times (each frame is 64 clocks). We wait a maximum of 6 subframes.
+ * We really should try doing something more productive while we
+ * wait.
+ */
+static unsigned int
+mcp_sa11x0_read(struct mcp *mcp, unsigned int reg)
+{
+ int ret = -ETIME;
+ int i;
+
+ Ser4MCDR2 = reg << 17 | MCDR2_Rd;
+
+ for (i = 0; i < 2; i++) {
+ udelay(mcp->rw_timeout);
+ if (Ser4MCSR & MCSR_CRC) {
+ ret = Ser4MCDR2 & 0xffff;
+ break;
+ }
+ }
+
+ if (ret < 0)
+ printk(KERN_WARNING "mcp: read timed out\n");
+
+ return ret;
+}
+
+static void mcp_sa11x0_enable(struct mcp *mcp)
+{
+ Ser4MCSR = -1;
+ Ser4MCCR0 |= MCCR0_MCE;
+}
+
+static void mcp_sa11x0_disable(struct mcp *mcp)
+{
+ Ser4MCCR0 &= ~MCCR0_MCE;
+}
+
+/*
+ * Our methods.
+ */
+static struct mcp_ops mcp_sa11x0 = {
+ .set_telecom_divisor = mcp_sa11x0_set_telecom_divisor,
+ .set_audio_divisor = mcp_sa11x0_set_audio_divisor,
+ .reg_write = mcp_sa11x0_write,
+ .reg_read = mcp_sa11x0_read,
+ .enable = mcp_sa11x0_enable,
+ .disable = mcp_sa11x0_disable,
+};
+
+static int mcp_sa11x0_probe(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct mcp_plat_data *data = pdev->dev.platform_data;
+ struct mcp *mcp;
+ int ret;
+
+ if (!data)
+ return -ENODEV;
+
+ if (!request_mem_region(0x80060000, 0x60, "sa11x0-mcp"))
+ return -EBUSY;
+
+ mcp = mcp_host_alloc(&pdev->dev, sizeof(struct mcp_sa11x0));
+ if (!mcp) {
+ ret = -ENOMEM;
+ goto release;
+ }
+
+ mcp->owner = THIS_MODULE;
+ mcp->ops = &mcp_sa11x0;
+ mcp->sclk_rate = data->sclk_rate;
+ mcp->dma_audio_rd = DMA_Ser4MCP0Rd;
+ mcp->dma_audio_wr = DMA_Ser4MCP0Wr;
+ mcp->dma_telco_rd = DMA_Ser4MCP1Rd;
+ mcp->dma_telco_wr = DMA_Ser4MCP1Wr;
+
+ dev_set_drvdata(dev, mcp);
+
+ if (machine_is_assabet()) {
+ ASSABET_BCR_set(ASSABET_BCR_CODEC_RST);
+ }
+
+ /*
+ * Setup the PPC unit correctly.
+ */
+ PPDR &= ~PPC_RXD4;
+ PPDR |= PPC_TXD4 | PPC_SCLK | PPC_SFRM;
+ PSDR |= PPC_RXD4;
+ PSDR &= ~(PPC_TXD4 | PPC_SCLK | PPC_SFRM);
+ PPSR &= ~(PPC_TXD4 | PPC_SCLK | PPC_SFRM);
+
+ /*
+ * Initialise device. Note that we initially
+ * set the sampling rate to minimum.
+ */
+ Ser4MCSR = -1;
+ Ser4MCCR1 = data->mccr1;
+ Ser4MCCR0 = data->mccr0 | 0x7f7f;
+
+ /*
+ * Calculate the read/write timeout (us) from the bit clock
+ * rate. This is the period for 3 64-bit frames. Always
+ * round this time up.
+ */
+ mcp->rw_timeout = (64 * 3 * 1000000 + mcp->sclk_rate - 1) /
+ mcp->sclk_rate;
+
+ ret = mcp_host_register(mcp);
+ if (ret == 0)
+ goto out;
+
+ release:
+ release_mem_region(0x80060000, 0x60);
+ dev_set_drvdata(dev, NULL);
+
+ out:
+ return ret;
+}
+
+static int mcp_sa11x0_remove(struct device *dev)
+{
+ struct mcp *mcp = dev_get_drvdata(dev);
+
+ dev_set_drvdata(dev, NULL);
+ mcp_host_unregister(mcp);
+ release_mem_region(0x80060000, 0x60);
+
+ return 0;
+}
+
+static int mcp_sa11x0_suspend(struct device *dev, pm_message_t state, u32 level)
+{
+ struct mcp *mcp = dev_get_drvdata(dev);
+
+ if (level == SUSPEND_DISABLE) {
+ priv(mcp)->mccr0 = Ser4MCCR0;
+ priv(mcp)->mccr1 = Ser4MCCR1;
+ Ser4MCCR0 &= ~MCCR0_MCE;
+ }
+ return 0;
+}
+
+static int mcp_sa11x0_resume(struct device *dev, u32 level)
+{
+ struct mcp *mcp = dev_get_drvdata(dev);
+
+ if (level == RESUME_RESTORE_STATE) {
+ Ser4MCCR1 = priv(mcp)->mccr1;
+ Ser4MCCR0 = priv(mcp)->mccr0;
+ }
+ return 0;
+}
+
+/*
+ * The driver for the SA11x0 MCP port.
+ */
+static struct device_driver mcp_sa11x0_driver = {
+ .name = "sa11x0-mcp",
+ .bus = &platform_bus_type,
+ .probe = mcp_sa11x0_probe,
+ .remove = mcp_sa11x0_remove,
+ .suspend = mcp_sa11x0_suspend,
+ .resume = mcp_sa11x0_resume,
+};
+
+/*
+ * This needs re-working
+ */
+static int __init mcp_sa11x0_init(void)
+{
+ return driver_register(&mcp_sa11x0_driver);
+}
+
+static void __exit mcp_sa11x0_exit(void)
+{
+ driver_unregister(&mcp_sa11x0_driver);
+}
+
+module_init(mcp_sa11x0_init);
+module_exit(mcp_sa11x0_exit);
+
+MODULE_AUTHOR("Russell King <rmk@arm.linux.org.uk>");
+MODULE_DESCRIPTION("SA11x0 multimedia communications port driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/mfd/mcp.h b/drivers/mfd/mcp.h
new file mode 100644
index 0000000..c093a93
--- /dev/null
+++ b/drivers/mfd/mcp.h
@@ -0,0 +1,66 @@
+/*
+ * linux/drivers/mfd/mcp.h
+ *
+ * Copyright (C) 2001 Russell King, All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License.
+ */
+#ifndef MCP_H
+#define MCP_H
+
+struct mcp_ops;
+
+struct mcp {
+ struct module *owner;
+ struct mcp_ops *ops;
+ spinlock_t lock;
+ int use_count;
+ unsigned int sclk_rate;
+ unsigned int rw_timeout;
+ dma_device_t dma_audio_rd;
+ dma_device_t dma_audio_wr;
+ dma_device_t dma_telco_rd;
+ dma_device_t dma_telco_wr;
+ struct device attached_device;
+};
+
+struct mcp_ops {
+ void (*set_telecom_divisor)(struct mcp *, unsigned int);
+ void (*set_audio_divisor)(struct mcp *, unsigned int);
+ void (*reg_write)(struct mcp *, unsigned int, unsigned int);
+ unsigned int (*reg_read)(struct mcp *, unsigned int);
+ void (*enable)(struct mcp *);
+ void (*disable)(struct mcp *);
+};
+
+void mcp_set_telecom_divisor(struct mcp *, unsigned int);
+void mcp_set_audio_divisor(struct mcp *, unsigned int);
+void mcp_reg_write(struct mcp *, unsigned int, unsigned int);
+unsigned int mcp_reg_read(struct mcp *, unsigned int);
+void mcp_enable(struct mcp *);
+void mcp_disable(struct mcp *);
+#define mcp_get_sclk_rate(mcp) ((mcp)->sclk_rate)
+
+struct mcp *mcp_host_alloc(struct device *, size_t);
+int mcp_host_register(struct mcp *);
+void mcp_host_unregister(struct mcp *);
+
+struct mcp_driver {
+ struct device_driver drv;
+ int (*probe)(struct mcp *);
+ void (*remove)(struct mcp *);
+ int (*suspend)(struct mcp *, pm_message_t);
+ int (*resume)(struct mcp *);
+};
+
+int mcp_driver_register(struct mcp_driver *);
+void mcp_driver_unregister(struct mcp_driver *);
+
+#define mcp_get_drvdata(mcp) dev_get_drvdata(&(mcp)->attached_device)
+#define mcp_set_drvdata(mcp,d) dev_set_drvdata(&(mcp)->attached_device, d)
+
+#define mcp_priv(mcp) ((void *)((mcp)+1))
+
+#endif
diff --git a/drivers/mmc/mmc.c b/drivers/mmc/mmc.c
index eeb9f66..3c59048 100644
--- a/drivers/mmc/mmc.c
+++ b/drivers/mmc/mmc.c
@@ -361,7 +361,7 @@
default:
printk("%s: card has unknown MMCA version %d\n",
- card->host->host_name, card->csd.mmca_vsn);
+ mmc_hostname(card->host), card->csd.mmca_vsn);
mmc_card_set_bad(card);
break;
}
@@ -383,7 +383,7 @@
csd_struct = UNSTUFF_BITS(resp, 126, 2);
if (csd_struct != 1 && csd_struct != 2) {
printk("%s: unrecognised CSD structure version %d\n",
- card->host->host_name, csd_struct);
+ mmc_hostname(card->host), csd_struct);
mmc_card_set_bad(card);
return;
}
@@ -551,7 +551,7 @@
}
if (err != MMC_ERR_NONE) {
printk(KERN_ERR "%s: error requesting CID: %d\n",
- host->host_name, err);
+ mmc_hostname(host), err);
break;
}
@@ -796,17 +796,13 @@
{
struct mmc_host *host;
- host = kmalloc(sizeof(struct mmc_host) + extra, GFP_KERNEL);
+ host = mmc_alloc_host_sysfs(extra, dev);
if (host) {
- memset(host, 0, sizeof(struct mmc_host) + extra);
-
spin_lock_init(&host->lock);
init_waitqueue_head(&host->wq);
INIT_LIST_HEAD(&host->cards);
INIT_WORK(&host->detect, mmc_rescan, host);
- host->dev = dev;
-
/*
* By default, hosts do not support SGIO or large requests.
* They have to set these according to their abilities.
@@ -828,15 +824,15 @@
*/
int mmc_add_host(struct mmc_host *host)
{
- static unsigned int host_num;
+ int ret;
- snprintf(host->host_name, sizeof(host->host_name),
- "mmc%d", host_num++);
+ ret = mmc_add_host_sysfs(host);
+ if (ret == 0) {
+ mmc_power_off(host);
+ mmc_detect_change(host);
+ }
- mmc_power_off(host);
- mmc_detect_change(host);
-
- return 0;
+ return ret;
}
EXPORT_SYMBOL(mmc_add_host);
@@ -859,6 +855,7 @@
}
mmc_power_off(host);
+ mmc_remove_host_sysfs(host);
}
EXPORT_SYMBOL(mmc_remove_host);
@@ -872,7 +869,7 @@
void mmc_free_host(struct mmc_host *host)
{
flush_scheduled_work();
- kfree(host);
+ mmc_free_host_sysfs(host);
}
EXPORT_SYMBOL(mmc_free_host);
diff --git a/drivers/mmc/mmc.h b/drivers/mmc/mmc.h
index b498dff..97bae00 100644
--- a/drivers/mmc/mmc.h
+++ b/drivers/mmc/mmc.h
@@ -13,4 +13,9 @@
void mmc_init_card(struct mmc_card *card, struct mmc_host *host);
int mmc_register_card(struct mmc_card *card);
void mmc_remove_card(struct mmc_card *card);
+
+struct mmc_host *mmc_alloc_host_sysfs(int extra, struct device *dev);
+int mmc_add_host_sysfs(struct mmc_host *host);
+void mmc_remove_host_sysfs(struct mmc_host *host);
+void mmc_free_host_sysfs(struct mmc_host *host);
#endif
diff --git a/drivers/mmc/mmc_sysfs.c b/drivers/mmc/mmc_sysfs.c
index 5556cd3..ad89498 100644
--- a/drivers/mmc/mmc_sysfs.c
+++ b/drivers/mmc/mmc_sysfs.c
@@ -12,6 +12,7 @@
#include <linux/module.h>
#include <linux/init.h>
#include <linux/device.h>
+#include <linux/idr.h>
#include <linux/mmc/card.h>
#include <linux/mmc/host.h>
@@ -20,6 +21,7 @@
#define dev_to_mmc_card(d) container_of(d, struct mmc_card, dev)
#define to_mmc_driver(d) container_of(d, struct mmc_driver, drv)
+#define cls_dev_to_mmc_host(d) container_of(d, struct mmc_host, class_dev)
#define MMC_ATTR(name, fmt, args...) \
static ssize_t mmc_##name##_show (struct device *dev, struct device_attribute *attr, char *buf) \
@@ -206,7 +208,7 @@
int mmc_register_card(struct mmc_card *card)
{
snprintf(card->dev.bus_id, sizeof(card->dev.bus_id),
- "%s:%04x", card->host->host_name, card->rca);
+ "%s:%04x", mmc_hostname(card->host), card->rca);
return device_add(&card->dev);
}
@@ -224,13 +226,97 @@
}
+static void mmc_host_classdev_release(struct class_device *dev)
+{
+ struct mmc_host *host = cls_dev_to_mmc_host(dev);
+ kfree(host);
+}
+
+static struct class mmc_host_class = {
+ .name = "mmc_host",
+ .release = mmc_host_classdev_release,
+};
+
+static DEFINE_IDR(mmc_host_idr);
+static DEFINE_SPINLOCK(mmc_host_lock);
+
+/*
+ * Internal function. Allocate a new MMC host.
+ */
+struct mmc_host *mmc_alloc_host_sysfs(int extra, struct device *dev)
+{
+ struct mmc_host *host;
+
+ host = kmalloc(sizeof(struct mmc_host) + extra, GFP_KERNEL);
+ if (host) {
+ memset(host, 0, sizeof(struct mmc_host) + extra);
+
+ host->dev = dev;
+ host->class_dev.dev = host->dev;
+ host->class_dev.class = &mmc_host_class;
+ class_device_initialize(&host->class_dev);
+ }
+
+ return host;
+}
+
+/*
+ * Internal function. Register a new MMC host with the MMC class.
+ */
+int mmc_add_host_sysfs(struct mmc_host *host)
+{
+ int err;
+
+ if (!idr_pre_get(&mmc_host_idr, GFP_KERNEL))
+ return -ENOMEM;
+
+ spin_lock(&mmc_host_lock);
+ err = idr_get_new(&mmc_host_idr, host, &host->index);
+ spin_unlock(&mmc_host_lock);
+ if (err)
+ return err;
+
+ snprintf(host->class_dev.class_id, BUS_ID_SIZE,
+ "mmc%d", host->index);
+
+ return class_device_add(&host->class_dev);
+}
+
+/*
+ * Internal function. Unregister a MMC host with the MMC class.
+ */
+void mmc_remove_host_sysfs(struct mmc_host *host)
+{
+ class_device_del(&host->class_dev);
+
+ spin_lock(&mmc_host_lock);
+ idr_remove(&mmc_host_idr, host->index);
+ spin_unlock(&mmc_host_lock);
+}
+
+/*
+ * Internal function. Free a MMC host.
+ */
+void mmc_free_host_sysfs(struct mmc_host *host)
+{
+ class_device_put(&host->class_dev);
+}
+
+
static int __init mmc_init(void)
{
- return bus_register(&mmc_bus_type);
+ int ret = bus_register(&mmc_bus_type);
+ if (ret == 0) {
+ ret = class_register(&mmc_host_class);
+ if (ret)
+ bus_unregister(&mmc_bus_type);
+ }
+ return ret;
}
static void __exit mmc_exit(void)
{
+ class_unregister(&mmc_host_class);
bus_unregister(&mmc_bus_type);
}
diff --git a/drivers/mmc/mmci.c b/drivers/mmc/mmci.c
index 7a42966..716c4ef 100644
--- a/drivers/mmc/mmci.c
+++ b/drivers/mmc/mmci.c
@@ -34,7 +34,7 @@
#ifdef CONFIG_MMC_DEBUG
#define DBG(host,fmt,args...) \
- pr_debug("%s: %s: " fmt, host->mmc->host_name, __func__ , args)
+ pr_debug("%s: %s: " fmt, mmc_hostname(host->mmc), __func__ , args)
#else
#define DBG(host,fmt,args...) do { } while (0)
#endif
@@ -541,7 +541,7 @@
mmc_add_host(mmc);
printk(KERN_INFO "%s: MMCI rev %x cfg %02x at 0x%08lx irq %d,%d\n",
- mmc->host_name, amba_rev(dev), amba_config(dev),
+ mmc_hostname(mmc), amba_rev(dev), amba_config(dev),
dev->res.start, dev->irq[0], dev->irq[1]);
init_timer(&host->timer);
diff --git a/drivers/mmc/wbsd.c b/drivers/mmc/wbsd.c
index 974f2f3..402c2d6 100644
--- a/drivers/mmc/wbsd.c
+++ b/drivers/mmc/wbsd.c
@@ -1796,7 +1796,7 @@
mmc_add_host(mmc);
- printk(KERN_INFO "%s: W83L51xD", mmc->host_name);
+ printk(KERN_INFO "%s: W83L51xD", mmc_hostname(mmc));
if (host->chip_id != 0)
printk(" id %x", (int)host->chip_id);
printk(" at 0x%x irq %d", (int)host->base, (int)host->irq);
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 8edb693..79e8aa6 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -131,6 +131,8 @@
source "drivers/net/arcnet/Kconfig"
+source "drivers/net/phy/Kconfig"
+
#
# Ethernet
#
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 63c6d1e..a369ae2 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -65,6 +65,7 @@
#
obj-$(CONFIG_MII) += mii.o
+obj-$(CONFIG_PHYLIB) += phy/
obj-$(CONFIG_SUNDANCE) += sundance.o
obj-$(CONFIG_HAMACHI) += hamachi.o
diff --git a/drivers/net/Space.c b/drivers/net/Space.c
index 3707df6..60304f7 100644
--- a/drivers/net/Space.c
+++ b/drivers/net/Space.c
@@ -87,7 +87,6 @@
extern struct net_device *tc515_probe(int unit);
extern struct net_device *lance_probe(int unit);
extern struct net_device *mace_probe(int unit);
-extern struct net_device *macsonic_probe(int unit);
extern struct net_device *mac8390_probe(int unit);
extern struct net_device *mac89x0_probe(int unit);
extern struct net_device *mc32_probe(int unit);
@@ -284,9 +283,6 @@
#ifdef CONFIG_MACMACE /* Mac 68k Quadra AV builtin Ethernet */
{mace_probe, 0},
#endif
-#ifdef CONFIG_MACSONIC /* Mac SONIC-based Ethernet of all sorts */
- {macsonic_probe, 0},
-#endif
#ifdef CONFIG_MAC8390 /* NuBus NS8390-based cards */
{mac8390_probe, 0},
#endif
@@ -318,17 +314,9 @@
#ifdef CONFIG_TR
/* Token-ring device probe */
extern int ibmtr_probe_card(struct net_device *);
-extern struct net_device *sk_isa_probe(int unit);
-extern struct net_device *proteon_probe(int unit);
extern struct net_device *smctr_probe(int unit);
static struct devprobe2 tr_probes2[] __initdata = {
-#ifdef CONFIG_SKISA
- {sk_isa_probe, 0},
-#endif
-#ifdef CONFIG_PROTEON
- {proteon_probe, 0},
-#endif
#ifdef CONFIG_SMCTR
{smctr_probe, 0},
#endif
diff --git a/drivers/net/bonding/bond_alb.c b/drivers/net/bonding/bond_alb.c
index 5ce606d..19e829b 100644
--- a/drivers/net/bonding/bond_alb.c
+++ b/drivers/net/bonding/bond_alb.c
@@ -1106,18 +1106,13 @@
}
}
- if (found) {
- /* a slave was found that is using the mac address
- * of the new slave
- */
- printk(KERN_ERR DRV_NAME
- ": Error: the hw address of slave %s is not "
- "unique - cannot enslave it!",
- slave->dev->name);
- return -EINVAL;
- }
+ if (!found)
+ return 0;
- return 0;
+ /* Try setting slave mac to bond address and fall-through
+ to code handling that situation below... */
+ alb_set_slave_mac_addr(slave, bond->dev->dev_addr,
+ bond->alb_info.rlb_enabled);
}
/* The slave's address is equal to the address of the bond.
diff --git a/drivers/net/bonding/bond_main.c b/drivers/net/bonding/bond_main.c
index 2c930da..94c9f68 100644
--- a/drivers/net/bonding/bond_main.c
+++ b/drivers/net/bonding/bond_main.c
@@ -1604,6 +1604,44 @@
return 0;
}
+#define BOND_INTERSECT_FEATURES \
+ (NETIF_F_SG|NETIF_F_IP_CSUM|NETIF_F_NO_CSUM|NETIF_F_HW_CSUM)
+
+/*
+ * Compute the features available to the bonding device by
+ * intersection of all of the slave devices' BOND_INTERSECT_FEATURES.
+ * Call this after attaching or detaching a slave to update the
+ * bond's features.
+ */
+static int bond_compute_features(struct bonding *bond)
+{
+ int i;
+ struct slave *slave;
+ struct net_device *bond_dev = bond->dev;
+ int features = bond->bond_features;
+
+ bond_for_each_slave(bond, slave, i) {
+ struct net_device * slave_dev = slave->dev;
+ if (i == 0) {
+ features |= BOND_INTERSECT_FEATURES;
+ }
+ features &=
+ ~(~slave_dev->features & BOND_INTERSECT_FEATURES);
+ }
+
+ /* turn off NETIF_F_SG if we need a csum and h/w can't do it */
+ if ((features & NETIF_F_SG) &&
+ !(features & (NETIF_F_IP_CSUM |
+ NETIF_F_NO_CSUM |
+ NETIF_F_HW_CSUM))) {
+ features &= ~NETIF_F_SG;
+ }
+
+ bond_dev->features = features;
+
+ return 0;
+}
+
/* enslave device <slave> to bond device <master> */
static int bond_enslave(struct net_device *bond_dev, struct net_device *slave_dev)
{
@@ -1811,6 +1849,8 @@
new_slave->delay = 0;
new_slave->link_failure_count = 0;
+ bond_compute_features(bond);
+
if (bond->params.miimon && !bond->params.use_carrier) {
link_reporting = bond_check_dev_link(bond, slave_dev, 1);
@@ -2015,7 +2055,7 @@
err_undo_flags:
bond_dev->features = old_features;
-
+
return res;
}
@@ -2100,6 +2140,8 @@
/* release the slave from its bond */
bond_detach_slave(bond, slave);
+ bond_compute_features(bond);
+
if (bond->primary_slave == slave) {
bond->primary_slave = NULL;
}
@@ -2243,6 +2285,8 @@
bond_alb_deinit_slave(bond, slave);
}
+ bond_compute_features(bond);
+
/* now that the slave is detached, unlock and perform
* all the undo steps that should not be called from
* within a lock.
@@ -3588,6 +3632,7 @@
static int bond_slave_netdev_event(unsigned long event, struct net_device *slave_dev)
{
struct net_device *bond_dev = slave_dev->master;
+ struct bonding *bond = bond_dev->priv;
switch (event) {
case NETDEV_UNREGISTER:
@@ -3626,6 +3671,9 @@
* TODO: handle changing the primary's name
*/
break;
+ case NETDEV_FEAT_CHANGE:
+ bond_compute_features(bond);
+ break;
default:
break;
}
@@ -4526,6 +4574,11 @@
}
}
+static struct ethtool_ops bond_ethtool_ops = {
+ .get_tx_csum = ethtool_op_get_tx_csum,
+ .get_sg = ethtool_op_get_sg,
+};
+
/*
* Does not allocate but creates a /proc entry.
* Allowed to fail.
@@ -4555,6 +4608,7 @@
bond_dev->stop = bond_close;
bond_dev->get_stats = bond_get_stats;
bond_dev->do_ioctl = bond_do_ioctl;
+ bond_dev->ethtool_ops = &bond_ethtool_ops;
bond_dev->set_multicast_list = bond_set_multicast_list;
bond_dev->change_mtu = bond_change_mtu;
bond_dev->set_mac_address = bond_set_mac_address;
@@ -4591,6 +4645,8 @@
NETIF_F_HW_VLAN_RX |
NETIF_F_HW_VLAN_FILTER);
+ bond->bond_features = bond_dev->features;
+
#ifdef CONFIG_PROC_FS
bond_create_proc_entry(bond);
#endif
diff --git a/drivers/net/bonding/bonding.h b/drivers/net/bonding/bonding.h
index d27f377..3881969 100644
--- a/drivers/net/bonding/bonding.h
+++ b/drivers/net/bonding/bonding.h
@@ -211,6 +211,9 @@
struct bond_params params;
struct list_head vlan_list;
struct vlan_group *vlgrp;
+ /* the features the bonding device supports, independently
+ * of any slaves */
+ int bond_features;
};
/**
diff --git a/drivers/net/e1000/e1000_main.c b/drivers/net/e1000/e1000_main.c
index b82fd15..9b596e0 100644
--- a/drivers/net/e1000/e1000_main.c
+++ b/drivers/net/e1000/e1000_main.c
@@ -2767,7 +2767,7 @@
" next_to_use <%x>\n"
" next_to_clean <%x>\n"
"buffer_info[next_to_clean]\n"
- " dma <%zx>\n"
+ " dma <%llx>\n"
" time_stamp <%lx>\n"
" next_to_watch <%x>\n"
" jiffies <%lx>\n"
@@ -2776,7 +2776,7 @@
E1000_READ_REG(&adapter->hw, TDT),
tx_ring->next_to_use,
i,
- tx_ring->buffer_info[i].dma,
+ (unsigned long long)tx_ring->buffer_info[i].dma,
tx_ring->buffer_info[i].time_stamp,
eop,
jiffies,
diff --git a/drivers/net/eepro100.c b/drivers/net/eepro100.c
index 1795425..8c62ced 100644
--- a/drivers/net/eepro100.c
+++ b/drivers/net/eepro100.c
@@ -1263,8 +1263,8 @@
for (i = 0; i < RX_RING_SIZE; i++) {
struct sk_buff *skb;
skb = dev_alloc_skb(PKT_BUF_SZ + sizeof(struct RxFD));
- /* XXX: do we really want to call this before the NULL check? --hch */
- rx_align(skb); /* Align IP on 16 byte boundary */
+ if (skb)
+ rx_align(skb); /* Align IP on 16 byte boundary */
sp->rx_skbuff[i] = skb;
if (skb == NULL)
break; /* OK. Just initially short of Rx bufs. */
@@ -1654,8 +1654,8 @@
struct sk_buff *skb;
/* Get a fresh skbuff to replace the consumed one. */
skb = dev_alloc_skb(PKT_BUF_SZ + sizeof(struct RxFD));
- /* XXX: do we really want to call this before the NULL check? --hch */
- rx_align(skb); /* Align IP on 16 byte boundary */
+ if (skb)
+ rx_align(skb); /* Align IP on 16 byte boundary */
sp->rx_skbuff[entry] = skb;
if (skb == NULL) {
sp->rx_ringp[entry] = NULL;
diff --git a/drivers/net/forcedeth.c b/drivers/net/forcedeth.c
index 64f0f69..7d93948 100644
--- a/drivers/net/forcedeth.c
+++ b/drivers/net/forcedeth.c
@@ -85,6 +85,16 @@
* 0.33: 16 May 2005: Support for MCP51 added.
* 0.34: 18 Jun 2005: Add DEV_NEED_LINKTIMER to all nForce nics.
* 0.35: 26 Jun 2005: Support for MCP55 added.
+ * 0.36: 28 Jun 2005: Add jumbo frame support.
+ * 0.37: 10 Jul 2005: Additional ethtool support, cleanup of pci id list
+ * 0.38: 16 Jul 2005: tx irq rewrite: Use global flags instead of
+ * per-packet flags.
+ * 0.39: 18 Jul 2005: Add 64bit descriptor support.
+ * 0.40: 19 Jul 2005: Add support for mac address change.
+ * 0.41: 30 Jul 2005: Write back original MAC in nv_close instead
+ * of nv_remove
+ * 0.42: 06 Aug 2005: Fix lack of link speed initialization
+ * in the second (and later) nv_open call
*
* Known bugs:
* We suspect that on some hardware no TX done interrupts are generated.
@@ -96,7 +106,7 @@
* DEV_NEED_TIMERIRQ will not harm you on sane hardware, only generating a few
* superfluous timer interrupts from the nic.
*/
-#define FORCEDETH_VERSION "0.35"
+#define FORCEDETH_VERSION "0.41"
#define DRV_NAME "forcedeth"
#include <linux/module.h>
@@ -131,11 +141,10 @@
* Hardware access:
*/
-#define DEV_NEED_LASTPACKET1 0x0001 /* set LASTPACKET1 in tx flags */
-#define DEV_IRQMASK_1 0x0002 /* use NVREG_IRQMASK_WANTED_1 for irq mask */
-#define DEV_IRQMASK_2 0x0004 /* use NVREG_IRQMASK_WANTED_2 for irq mask */
-#define DEV_NEED_TIMERIRQ 0x0008 /* set the timer irq flag in the irq mask */
-#define DEV_NEED_LINKTIMER 0x0010 /* poll link settings. Relies on the timer irq */
+#define DEV_NEED_TIMERIRQ 0x0001 /* set the timer irq flag in the irq mask */
+#define DEV_NEED_LINKTIMER 0x0002 /* poll link settings. Relies on the timer irq */
+#define DEV_HAS_LARGEDESC 0x0004 /* device supports jumbo frames and needs packet format 2 */
+#define DEV_HAS_HIGH_DMA 0x0008 /* device supports 64bit dma */
enum {
NvRegIrqStatus = 0x000,
@@ -146,13 +155,16 @@
#define NVREG_IRQ_RX 0x0002
#define NVREG_IRQ_RX_NOBUF 0x0004
#define NVREG_IRQ_TX_ERR 0x0008
-#define NVREG_IRQ_TX2 0x0010
+#define NVREG_IRQ_TX_OK 0x0010
#define NVREG_IRQ_TIMER 0x0020
#define NVREG_IRQ_LINK 0x0040
+#define NVREG_IRQ_TX_ERROR 0x0080
#define NVREG_IRQ_TX1 0x0100
-#define NVREG_IRQMASK_WANTED_1 0x005f
-#define NVREG_IRQMASK_WANTED_2 0x0147
-#define NVREG_IRQ_UNKNOWN (~(NVREG_IRQ_RX_ERROR|NVREG_IRQ_RX|NVREG_IRQ_RX_NOBUF|NVREG_IRQ_TX_ERR|NVREG_IRQ_TX2|NVREG_IRQ_TIMER|NVREG_IRQ_LINK|NVREG_IRQ_TX1))
+#define NVREG_IRQMASK_WANTED 0x00df
+
+#define NVREG_IRQ_UNKNOWN (~(NVREG_IRQ_RX_ERROR|NVREG_IRQ_RX|NVREG_IRQ_RX_NOBUF|NVREG_IRQ_TX_ERR| \
+ NVREG_IRQ_TX_OK|NVREG_IRQ_TIMER|NVREG_IRQ_LINK|NVREG_IRQ_TX_ERROR| \
+ NVREG_IRQ_TX1))
NvRegUnknownSetupReg6 = 0x008,
#define NVREG_UNKSETUP6_VAL 3
@@ -286,6 +298,18 @@
u32 FlagLen;
};
+struct ring_desc_ex {
+ u32 PacketBufferHigh;
+ u32 PacketBufferLow;
+ u32 Reserved;
+ u32 FlagLen;
+};
+
+typedef union _ring_type {
+ struct ring_desc* orig;
+ struct ring_desc_ex* ex;
+} ring_type;
+
#define FLAG_MASK_V1 0xffff0000
#define FLAG_MASK_V2 0xffffc000
#define LEN_MASK_V1 (0xffffffff ^ FLAG_MASK_V1)
@@ -293,7 +317,7 @@
#define NV_TX_LASTPACKET (1<<16)
#define NV_TX_RETRYERROR (1<<19)
-#define NV_TX_LASTPACKET1 (1<<24)
+#define NV_TX_FORCED_INTERRUPT (1<<24)
#define NV_TX_DEFERRED (1<<26)
#define NV_TX_CARRIERLOST (1<<27)
#define NV_TX_LATECOLLISION (1<<28)
@@ -303,7 +327,7 @@
#define NV_TX2_LASTPACKET (1<<29)
#define NV_TX2_RETRYERROR (1<<18)
-#define NV_TX2_LASTPACKET1 (1<<23)
+#define NV_TX2_FORCED_INTERRUPT (1<<30)
#define NV_TX2_DEFERRED (1<<25)
#define NV_TX2_CARRIERLOST (1<<26)
#define NV_TX2_LATECOLLISION (1<<27)
@@ -379,9 +403,13 @@
#define TX_LIMIT_START 62
/* rx/tx mac addr + type + vlan + align + slack*/
-#define RX_NIC_BUFSIZE (ETH_DATA_LEN + 64)
-/* even more slack */
-#define RX_ALLOC_BUFSIZE (ETH_DATA_LEN + 128)
+#define NV_RX_HEADERS (64)
+/* even more slack. */
+#define NV_RX_ALLOC_PAD (64)
+
+/* maximum mtu size */
+#define NV_PKTLIMIT_1 ETH_DATA_LEN /* hard limit not known */
+#define NV_PKTLIMIT_2 9100 /* Actual limit according to NVidia: 9202 */
#define OOM_REFILL (1+HZ/20)
#define POLL_WAIT (1+HZ/100)
@@ -396,6 +424,7 @@
*/
#define DESC_VER_1 0x0
#define DESC_VER_2 (0x02100|NVREG_TXRXCTL_RXCHECK)
+#define DESC_VER_3 (0x02200|NVREG_TXRXCTL_RXCHECK)
/* PHY defines */
#define PHY_OUI_MARVELL 0x5043
@@ -468,11 +497,12 @@
/* rx specific fields.
* Locking: Within irq hander or disable_irq+spin_lock(&np->lock);
*/
- struct ring_desc *rx_ring;
+ ring_type rx_ring;
unsigned int cur_rx, refill_rx;
struct sk_buff *rx_skbuff[RX_RING];
dma_addr_t rx_dma[RX_RING];
unsigned int rx_buf_sz;
+ unsigned int pkt_limit;
struct timer_list oom_kick;
struct timer_list nic_poll;
@@ -484,7 +514,7 @@
/*
* tx specific fields.
*/
- struct ring_desc *tx_ring;
+ ring_type tx_ring;
unsigned int next_tx, nic_tx;
struct sk_buff *tx_skbuff[TX_RING];
dma_addr_t tx_dma[TX_RING];
@@ -519,6 +549,11 @@
& ((v == DESC_VER_1) ? LEN_MASK_V1 : LEN_MASK_V2);
}
+static inline u32 nv_descr_getlength_ex(struct ring_desc_ex *prd, u32 v)
+{
+ return le32_to_cpu(prd->FlagLen) & LEN_MASK_V2;
+}
+
static int reg_delay(struct net_device *dev, int offset, u32 mask, u32 target,
int delay, int delaymax, const char *msg)
{
@@ -792,7 +827,7 @@
nr = refill_rx % RX_RING;
if (np->rx_skbuff[nr] == NULL) {
- skb = dev_alloc_skb(RX_ALLOC_BUFSIZE);
+ skb = dev_alloc_skb(np->rx_buf_sz + NV_RX_ALLOC_PAD);
if (!skb)
break;
@@ -803,9 +838,16 @@
}
np->rx_dma[nr] = pci_map_single(np->pci_dev, skb->data, skb->len,
PCI_DMA_FROMDEVICE);
- np->rx_ring[nr].PacketBuffer = cpu_to_le32(np->rx_dma[nr]);
- wmb();
- np->rx_ring[nr].FlagLen = cpu_to_le32(RX_NIC_BUFSIZE | NV_RX_AVAIL);
+ if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2) {
+ np->rx_ring.orig[nr].PacketBuffer = cpu_to_le32(np->rx_dma[nr]);
+ wmb();
+ np->rx_ring.orig[nr].FlagLen = cpu_to_le32(np->rx_buf_sz | NV_RX_AVAIL);
+ } else {
+ np->rx_ring.ex[nr].PacketBufferHigh = cpu_to_le64(np->rx_dma[nr]) >> 32;
+ np->rx_ring.ex[nr].PacketBufferLow = cpu_to_le64(np->rx_dma[nr]) & 0x0FFFFFFFF;
+ wmb();
+ np->rx_ring.ex[nr].FlagLen = cpu_to_le32(np->rx_buf_sz | NV_RX2_AVAIL);
+ }
dprintk(KERN_DEBUG "%s: nv_alloc_rx: Packet %d marked as Available\n",
dev->name, refill_rx);
refill_rx++;
@@ -831,19 +873,37 @@
enable_irq(dev->irq);
}
-static int nv_init_ring(struct net_device *dev)
+static void nv_init_rx(struct net_device *dev)
+{
+ struct fe_priv *np = get_nvpriv(dev);
+ int i;
+
+ np->cur_rx = RX_RING;
+ np->refill_rx = 0;
+ for (i = 0; i < RX_RING; i++)
+ if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2)
+ np->rx_ring.orig[i].FlagLen = 0;
+ else
+ np->rx_ring.ex[i].FlagLen = 0;
+}
+
+static void nv_init_tx(struct net_device *dev)
{
struct fe_priv *np = get_nvpriv(dev);
int i;
np->next_tx = np->nic_tx = 0;
for (i = 0; i < TX_RING; i++)
- np->tx_ring[i].FlagLen = 0;
+ if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2)
+ np->tx_ring.orig[i].FlagLen = 0;
+ else
+ np->tx_ring.ex[i].FlagLen = 0;
+}
- np->cur_rx = RX_RING;
- np->refill_rx = 0;
- for (i = 0; i < RX_RING; i++)
- np->rx_ring[i].FlagLen = 0;
+static int nv_init_ring(struct net_device *dev)
+{
+ nv_init_tx(dev);
+ nv_init_rx(dev);
return nv_alloc_rx(dev);
}
@@ -852,7 +912,10 @@
struct fe_priv *np = get_nvpriv(dev);
int i;
for (i = 0; i < TX_RING; i++) {
- np->tx_ring[i].FlagLen = 0;
+ if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2)
+ np->tx_ring.orig[i].FlagLen = 0;
+ else
+ np->tx_ring.ex[i].FlagLen = 0;
if (np->tx_skbuff[i]) {
pci_unmap_single(np->pci_dev, np->tx_dma[i],
np->tx_skbuff[i]->len,
@@ -869,7 +932,10 @@
struct fe_priv *np = get_nvpriv(dev);
int i;
for (i = 0; i < RX_RING; i++) {
- np->rx_ring[i].FlagLen = 0;
+ if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2)
+ np->rx_ring.orig[i].FlagLen = 0;
+ else
+ np->rx_ring.ex[i].FlagLen = 0;
wmb();
if (np->rx_skbuff[i]) {
pci_unmap_single(np->pci_dev, np->rx_dma[i],
@@ -900,11 +966,19 @@
np->tx_dma[nr] = pci_map_single(np->pci_dev, skb->data,skb->len,
PCI_DMA_TODEVICE);
- np->tx_ring[nr].PacketBuffer = cpu_to_le32(np->tx_dma[nr]);
+ if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2)
+ np->tx_ring.orig[nr].PacketBuffer = cpu_to_le32(np->tx_dma[nr]);
+ else {
+ np->tx_ring.ex[nr].PacketBufferHigh = cpu_to_le64(np->tx_dma[nr]) >> 32;
+ np->tx_ring.ex[nr].PacketBufferLow = cpu_to_le64(np->tx_dma[nr]) & 0x0FFFFFFFF;
+ }
spin_lock_irq(&np->lock);
wmb();
- np->tx_ring[nr].FlagLen = cpu_to_le32( (skb->len-1) | np->tx_flags );
+ if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2)
+ np->tx_ring.orig[nr].FlagLen = cpu_to_le32( (skb->len-1) | np->tx_flags );
+ else
+ np->tx_ring.ex[nr].FlagLen = cpu_to_le32( (skb->len-1) | np->tx_flags );
dprintk(KERN_DEBUG "%s: nv_start_xmit: packet packet %d queued for transmission.\n",
dev->name, np->next_tx);
{
@@ -942,7 +1016,10 @@
while (np->nic_tx != np->next_tx) {
i = np->nic_tx % TX_RING;
- Flags = le32_to_cpu(np->tx_ring[i].FlagLen);
+ if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2)
+ Flags = le32_to_cpu(np->tx_ring.orig[i].FlagLen);
+ else
+ Flags = le32_to_cpu(np->tx_ring.ex[i].FlagLen);
dprintk(KERN_DEBUG "%s: nv_tx_done: looking at packet %d, Flags 0x%x.\n",
dev->name, np->nic_tx, Flags);
@@ -993,9 +1070,56 @@
struct fe_priv *np = get_nvpriv(dev);
u8 __iomem *base = get_hwbase(dev);
- dprintk(KERN_DEBUG "%s: Got tx_timeout. irq: %08x\n", dev->name,
+ printk(KERN_INFO "%s: Got tx_timeout. irq: %08x\n", dev->name,
readl(base + NvRegIrqStatus) & NVREG_IRQSTAT_MASK);
+ {
+ int i;
+
+ printk(KERN_INFO "%s: Ring at %lx: next %d nic %d\n",
+ dev->name, (unsigned long)np->ring_addr,
+ np->next_tx, np->nic_tx);
+ printk(KERN_INFO "%s: Dumping tx registers\n", dev->name);
+ for (i=0;i<0x400;i+= 32) {
+ printk(KERN_INFO "%3x: %08x %08x %08x %08x %08x %08x %08x %08x\n",
+ i,
+ readl(base + i + 0), readl(base + i + 4),
+ readl(base + i + 8), readl(base + i + 12),
+ readl(base + i + 16), readl(base + i + 20),
+ readl(base + i + 24), readl(base + i + 28));
+ }
+ printk(KERN_INFO "%s: Dumping tx ring\n", dev->name);
+ for (i=0;i<TX_RING;i+= 4) {
+ if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2) {
+ printk(KERN_INFO "%03x: %08x %08x // %08x %08x // %08x %08x // %08x %08x\n",
+ i,
+ le32_to_cpu(np->tx_ring.orig[i].PacketBuffer),
+ le32_to_cpu(np->tx_ring.orig[i].FlagLen),
+ le32_to_cpu(np->tx_ring.orig[i+1].PacketBuffer),
+ le32_to_cpu(np->tx_ring.orig[i+1].FlagLen),
+ le32_to_cpu(np->tx_ring.orig[i+2].PacketBuffer),
+ le32_to_cpu(np->tx_ring.orig[i+2].FlagLen),
+ le32_to_cpu(np->tx_ring.orig[i+3].PacketBuffer),
+ le32_to_cpu(np->tx_ring.orig[i+3].FlagLen));
+ } else {
+ printk(KERN_INFO "%03x: %08x %08x %08x // %08x %08x %08x // %08x %08x %08x // %08x %08x %08x\n",
+ i,
+ le32_to_cpu(np->tx_ring.ex[i].PacketBufferHigh),
+ le32_to_cpu(np->tx_ring.ex[i].PacketBufferLow),
+ le32_to_cpu(np->tx_ring.ex[i].FlagLen),
+ le32_to_cpu(np->tx_ring.ex[i+1].PacketBufferHigh),
+ le32_to_cpu(np->tx_ring.ex[i+1].PacketBufferLow),
+ le32_to_cpu(np->tx_ring.ex[i+1].FlagLen),
+ le32_to_cpu(np->tx_ring.ex[i+2].PacketBufferHigh),
+ le32_to_cpu(np->tx_ring.ex[i+2].PacketBufferLow),
+ le32_to_cpu(np->tx_ring.ex[i+2].FlagLen),
+ le32_to_cpu(np->tx_ring.ex[i+3].PacketBufferHigh),
+ le32_to_cpu(np->tx_ring.ex[i+3].PacketBufferLow),
+ le32_to_cpu(np->tx_ring.ex[i+3].FlagLen));
+ }
+ }
+ }
+
spin_lock_irq(&np->lock);
/* 1) stop tx engine */
@@ -1009,7 +1133,10 @@
printk(KERN_DEBUG "%s: tx_timeout: dead entries!\n", dev->name);
nv_drain_tx(dev);
np->next_tx = np->nic_tx = 0;
- writel((u32) (np->ring_addr + RX_RING*sizeof(struct ring_desc)), base + NvRegTxRingPhysAddr);
+ if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2)
+ writel((u32) (np->ring_addr + RX_RING*sizeof(struct ring_desc)), base + NvRegTxRingPhysAddr);
+ else
+ writel((u32) (np->ring_addr + RX_RING*sizeof(struct ring_desc_ex)), base + NvRegTxRingPhysAddr);
netif_wake_queue(dev);
}
@@ -1084,8 +1211,13 @@
break; /* we scanned the whole ring - do not continue */
i = np->cur_rx % RX_RING;
- Flags = le32_to_cpu(np->rx_ring[i].FlagLen);
- len = nv_descr_getlength(&np->rx_ring[i], np->desc_ver);
+ if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2) {
+ Flags = le32_to_cpu(np->rx_ring.orig[i].FlagLen);
+ len = nv_descr_getlength(&np->rx_ring.orig[i], np->desc_ver);
+ } else {
+ Flags = le32_to_cpu(np->rx_ring.ex[i].FlagLen);
+ len = nv_descr_getlength_ex(&np->rx_ring.ex[i], np->desc_ver);
+ }
dprintk(KERN_DEBUG "%s: nv_rx_process: looking at packet %d, Flags 0x%x.\n",
dev->name, np->cur_rx, Flags);
@@ -1207,15 +1339,133 @@
}
}
+static void set_bufsize(struct net_device *dev)
+{
+ struct fe_priv *np = netdev_priv(dev);
+
+ if (dev->mtu <= ETH_DATA_LEN)
+ np->rx_buf_sz = ETH_DATA_LEN + NV_RX_HEADERS;
+ else
+ np->rx_buf_sz = dev->mtu + NV_RX_HEADERS;
+}
+
/*
* nv_change_mtu: dev->change_mtu function
* Called with dev_base_lock held for read.
*/
static int nv_change_mtu(struct net_device *dev, int new_mtu)
{
- if (new_mtu > ETH_DATA_LEN)
+ struct fe_priv *np = get_nvpriv(dev);
+ int old_mtu;
+
+ if (new_mtu < 64 || new_mtu > np->pkt_limit)
return -EINVAL;
+
+ old_mtu = dev->mtu;
dev->mtu = new_mtu;
+
+ /* return early if the buffer sizes will not change */
+ if (old_mtu <= ETH_DATA_LEN && new_mtu <= ETH_DATA_LEN)
+ return 0;
+ if (old_mtu == new_mtu)
+ return 0;
+
+ /* synchronized against open : rtnl_lock() held by caller */
+ if (netif_running(dev)) {
+ u8 *base = get_hwbase(dev);
+ /*
+ * It seems that the nic preloads valid ring entries into an
+ * internal buffer. The procedure for flushing everything is
+ * guessed, there is probably a simpler approach.
+ * Changing the MTU is a rare event, it shouldn't matter.
+ */
+ disable_irq(dev->irq);
+ spin_lock_bh(&dev->xmit_lock);
+ spin_lock(&np->lock);
+ /* stop engines */
+ nv_stop_rx(dev);
+ nv_stop_tx(dev);
+ nv_txrx_reset(dev);
+ /* drain rx queue */
+ nv_drain_rx(dev);
+ nv_drain_tx(dev);
+ /* reinit driver view of the rx queue */
+ nv_init_rx(dev);
+ nv_init_tx(dev);
+ /* alloc new rx buffers */
+ set_bufsize(dev);
+ if (nv_alloc_rx(dev)) {
+ if (!np->in_shutdown)
+ mod_timer(&np->oom_kick, jiffies + OOM_REFILL);
+ }
+ /* reinit nic view of the rx queue */
+ writel(np->rx_buf_sz, base + NvRegOffloadConfig);
+ writel((u32) np->ring_addr, base + NvRegRxRingPhysAddr);
+ if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2)
+ writel((u32) (np->ring_addr + RX_RING*sizeof(struct ring_desc)), base + NvRegTxRingPhysAddr);
+ else
+ writel((u32) (np->ring_addr + RX_RING*sizeof(struct ring_desc_ex)), base + NvRegTxRingPhysAddr);
+ writel( ((RX_RING-1) << NVREG_RINGSZ_RXSHIFT) + ((TX_RING-1) << NVREG_RINGSZ_TXSHIFT),
+ base + NvRegRingSizes);
+ pci_push(base);
+ writel(NVREG_TXRXCTL_KICK|np->desc_ver, get_hwbase(dev) + NvRegTxRxControl);
+ pci_push(base);
+
+ /* restart rx engine */
+ nv_start_rx(dev);
+ nv_start_tx(dev);
+ spin_unlock(&np->lock);
+ spin_unlock_bh(&dev->xmit_lock);
+ enable_irq(dev->irq);
+ }
+ return 0;
+}
+
+static void nv_copy_mac_to_hw(struct net_device *dev)
+{
+ u8 *base = get_hwbase(dev);
+ u32 mac[2];
+
+ mac[0] = (dev->dev_addr[0] << 0) + (dev->dev_addr[1] << 8) +
+ (dev->dev_addr[2] << 16) + (dev->dev_addr[3] << 24);
+ mac[1] = (dev->dev_addr[4] << 0) + (dev->dev_addr[5] << 8);
+
+ writel(mac[0], base + NvRegMacAddrA);
+ writel(mac[1], base + NvRegMacAddrB);
+}
+
+/*
+ * nv_set_mac_address: dev->set_mac_address function
+ * Called with rtnl_lock() held.
+ */
+static int nv_set_mac_address(struct net_device *dev, void *addr)
+{
+ struct fe_priv *np = get_nvpriv(dev);
+ struct sockaddr *macaddr = (struct sockaddr*)addr;
+
+ if(!is_valid_ether_addr(macaddr->sa_data))
+ return -EADDRNOTAVAIL;
+
+ /* synchronized against open : rtnl_lock() held by caller */
+ memcpy(dev->dev_addr, macaddr->sa_data, ETH_ALEN);
+
+ if (netif_running(dev)) {
+ spin_lock_bh(&dev->xmit_lock);
+ spin_lock_irq(&np->lock);
+
+ /* stop rx engine */
+ nv_stop_rx(dev);
+
+ /* set mac address */
+ nv_copy_mac_to_hw(dev);
+
+ /* restart rx engine */
+ nv_start_rx(dev);
+ spin_unlock_irq(&np->lock);
+ spin_unlock_bh(&dev->xmit_lock);
+ } else {
+ nv_copy_mac_to_hw(dev);
+ }
return 0;
}
@@ -1470,7 +1720,7 @@
if (!(events & np->irqmask))
break;
- if (events & (NVREG_IRQ_TX1|NVREG_IRQ_TX2|NVREG_IRQ_TX_ERR)) {
+ if (events & (NVREG_IRQ_TX1|NVREG_IRQ_TX_OK|NVREG_IRQ_TX_ERROR|NVREG_IRQ_TX_ERR)) {
spin_lock(&np->lock);
nv_tx_done(dev);
spin_unlock(&np->lock);
@@ -1761,6 +2011,50 @@
return 0;
}
+#define FORCEDETH_REGS_VER 1
+#define FORCEDETH_REGS_SIZE 0x400 /* 256 32-bit registers */
+
+static int nv_get_regs_len(struct net_device *dev)
+{
+ return FORCEDETH_REGS_SIZE;
+}
+
+static void nv_get_regs(struct net_device *dev, struct ethtool_regs *regs, void *buf)
+{
+ struct fe_priv *np = get_nvpriv(dev);
+ u8 __iomem *base = get_hwbase(dev);
+ u32 *rbuf = buf;
+ int i;
+
+ regs->version = FORCEDETH_REGS_VER;
+ spin_lock_irq(&np->lock);
+ for (i=0;i<FORCEDETH_REGS_SIZE/sizeof(u32);i++)
+ rbuf[i] = readl(base + i*sizeof(u32));
+ spin_unlock_irq(&np->lock);
+}
+
+static int nv_nway_reset(struct net_device *dev)
+{
+ struct fe_priv *np = get_nvpriv(dev);
+ int ret;
+
+ spin_lock_irq(&np->lock);
+ if (np->autoneg) {
+ int bmcr;
+
+ bmcr = mii_rw(dev, np->phyaddr, MII_BMCR, MII_READ);
+ bmcr |= (BMCR_ANENABLE | BMCR_ANRESTART);
+ mii_rw(dev, np->phyaddr, MII_BMCR, bmcr);
+
+ ret = 0;
+ } else {
+ ret = -EINVAL;
+ }
+ spin_unlock_irq(&np->lock);
+
+ return ret;
+}
+
static struct ethtool_ops ops = {
.get_drvinfo = nv_get_drvinfo,
.get_link = ethtool_op_get_link,
@@ -1768,6 +2062,9 @@
.set_wol = nv_set_wol,
.get_settings = nv_get_settings,
.set_settings = nv_set_settings,
+ .get_regs_len = nv_get_regs_len,
+ .get_regs = nv_get_regs,
+ .nway_reset = nv_nway_reset,
};
static int nv_open(struct net_device *dev)
@@ -1792,6 +2089,7 @@
writel(0, base + NvRegAdapterControl);
/* 2) initialize descriptor rings */
+ set_bufsize(dev);
oom = nv_init_ring(dev);
writel(0, base + NvRegLinkSpeed);
@@ -1802,20 +2100,14 @@
np->in_shutdown = 0;
/* 3) set mac address */
- {
- u32 mac[2];
-
- mac[0] = (dev->dev_addr[0] << 0) + (dev->dev_addr[1] << 8) +
- (dev->dev_addr[2] << 16) + (dev->dev_addr[3] << 24);
- mac[1] = (dev->dev_addr[4] << 0) + (dev->dev_addr[5] << 8);
-
- writel(mac[0], base + NvRegMacAddrA);
- writel(mac[1], base + NvRegMacAddrB);
- }
+ nv_copy_mac_to_hw(dev);
/* 4) give hw rings */
writel((u32) np->ring_addr, base + NvRegRxRingPhysAddr);
- writel((u32) (np->ring_addr + RX_RING*sizeof(struct ring_desc)), base + NvRegTxRingPhysAddr);
+ if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2)
+ writel((u32) (np->ring_addr + RX_RING*sizeof(struct ring_desc)), base + NvRegTxRingPhysAddr);
+ else
+ writel((u32) (np->ring_addr + RX_RING*sizeof(struct ring_desc_ex)), base + NvRegTxRingPhysAddr);
writel( ((RX_RING-1) << NVREG_RINGSZ_RXSHIFT) + ((TX_RING-1) << NVREG_RINGSZ_TXSHIFT),
base + NvRegRingSizes);
@@ -1837,7 +2129,7 @@
writel(NVREG_MISC1_FORCE | NVREG_MISC1_HD, base + NvRegMisc1);
writel(readl(base + NvRegTransmitterStatus), base + NvRegTransmitterStatus);
writel(NVREG_PFF_ALWAYS, base + NvRegPacketFilterFlags);
- writel(NVREG_OFFLOAD_NORMAL, base + NvRegOffloadConfig);
+ writel(np->rx_buf_sz, base + NvRegOffloadConfig);
writel(readl(base + NvRegReceiverStatus), base + NvRegReceiverStatus);
get_random_bytes(&i, sizeof(i));
@@ -1888,6 +2180,9 @@
writel(NVREG_MIISTAT_MASK, base + NvRegMIIStatus);
dprintk(KERN_INFO "startup: got 0x%08x.\n", miistat);
}
+ /* set linkspeed to invalid value, thus force nv_update_linkspeed
+ * to init hw */
+ np->linkspeed = 0;
ret = nv_update_linkspeed(dev);
nv_start_rx(dev);
nv_start_tx(dev);
@@ -1942,6 +2237,12 @@
if (np->wolenabled)
nv_start_rx(dev);
+ /* special op: write back the misordered MAC address - otherwise
+ * the next nv_probe would see a wrong address.
+ */
+ writel(np->orig_mac[0], base + NvRegMacAddrA);
+ writel(np->orig_mac[1], base + NvRegMacAddrB);
+
/* FIXME: power down nic */
return 0;
@@ -2006,32 +2307,55 @@
}
/* handle different descriptor versions */
- if (pci_dev->device == PCI_DEVICE_ID_NVIDIA_NVENET_1 ||
- pci_dev->device == PCI_DEVICE_ID_NVIDIA_NVENET_2 ||
- pci_dev->device == PCI_DEVICE_ID_NVIDIA_NVENET_3 ||
- pci_dev->device == PCI_DEVICE_ID_NVIDIA_NVENET_12 ||
- pci_dev->device == PCI_DEVICE_ID_NVIDIA_NVENET_13)
- np->desc_ver = DESC_VER_1;
- else
+ if (id->driver_data & DEV_HAS_HIGH_DMA) {
+ /* packet format 3: supports 40-bit addressing */
+ np->desc_ver = DESC_VER_3;
+ if (pci_set_dma_mask(pci_dev, 0x0000007fffffffffULL)) {
+ printk(KERN_INFO "forcedeth: 64-bit DMA failed, using 32-bit addressing for device %s.\n",
+ pci_name(pci_dev));
+ }
+ } else if (id->driver_data & DEV_HAS_LARGEDESC) {
+ /* packet format 2: supports jumbo frames */
np->desc_ver = DESC_VER_2;
+ } else {
+ /* original packet format */
+ np->desc_ver = DESC_VER_1;
+ }
+
+ np->pkt_limit = NV_PKTLIMIT_1;
+ if (id->driver_data & DEV_HAS_LARGEDESC)
+ np->pkt_limit = NV_PKTLIMIT_2;
err = -ENOMEM;
np->base = ioremap(addr, NV_PCI_REGSZ);
if (!np->base)
goto out_relreg;
dev->base_addr = (unsigned long)np->base;
+
dev->irq = pci_dev->irq;
- np->rx_ring = pci_alloc_consistent(pci_dev, sizeof(struct ring_desc) * (RX_RING + TX_RING),
- &np->ring_addr);
- if (!np->rx_ring)
- goto out_unmap;
- np->tx_ring = &np->rx_ring[RX_RING];
+
+ if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2) {
+ np->rx_ring.orig = pci_alloc_consistent(pci_dev,
+ sizeof(struct ring_desc) * (RX_RING + TX_RING),
+ &np->ring_addr);
+ if (!np->rx_ring.orig)
+ goto out_unmap;
+ np->tx_ring.orig = &np->rx_ring.orig[RX_RING];
+ } else {
+ np->rx_ring.ex = pci_alloc_consistent(pci_dev,
+ sizeof(struct ring_desc_ex) * (RX_RING + TX_RING),
+ &np->ring_addr);
+ if (!np->rx_ring.ex)
+ goto out_unmap;
+ np->tx_ring.ex = &np->rx_ring.ex[RX_RING];
+ }
dev->open = nv_open;
dev->stop = nv_close;
dev->hard_start_xmit = nv_start_xmit;
dev->get_stats = nv_get_stats;
dev->change_mtu = nv_change_mtu;
+ dev->set_mac_address = nv_set_mac_address;
dev->set_multicast_list = nv_set_multicast;
#ifdef CONFIG_NET_POLL_CONTROLLER
dev->poll_controller = nv_poll_controller;
@@ -2080,17 +2404,10 @@
if (np->desc_ver == DESC_VER_1) {
np->tx_flags = NV_TX_LASTPACKET|NV_TX_VALID;
- if (id->driver_data & DEV_NEED_LASTPACKET1)
- np->tx_flags |= NV_TX_LASTPACKET1;
} else {
np->tx_flags = NV_TX2_LASTPACKET|NV_TX2_VALID;
- if (id->driver_data & DEV_NEED_LASTPACKET1)
- np->tx_flags |= NV_TX2_LASTPACKET1;
}
- if (id->driver_data & DEV_IRQMASK_1)
- np->irqmask = NVREG_IRQMASK_WANTED_1;
- if (id->driver_data & DEV_IRQMASK_2)
- np->irqmask = NVREG_IRQMASK_WANTED_2;
+ np->irqmask = NVREG_IRQMASK_WANTED;
if (id->driver_data & DEV_NEED_TIMERIRQ)
np->irqmask |= NVREG_IRQ_TIMER;
if (id->driver_data & DEV_NEED_LINKTIMER) {
@@ -2155,8 +2472,12 @@
return 0;
out_freering:
- pci_free_consistent(np->pci_dev, sizeof(struct ring_desc) * (RX_RING + TX_RING),
- np->rx_ring, np->ring_addr);
+ if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2)
+ pci_free_consistent(np->pci_dev, sizeof(struct ring_desc) * (RX_RING + TX_RING),
+ np->rx_ring.orig, np->ring_addr);
+ else
+ pci_free_consistent(np->pci_dev, sizeof(struct ring_desc_ex) * (RX_RING + TX_RING),
+ np->rx_ring.ex, np->ring_addr);
pci_set_drvdata(pci_dev, NULL);
out_unmap:
iounmap(get_hwbase(dev));
@@ -2174,18 +2495,14 @@
{
struct net_device *dev = pci_get_drvdata(pci_dev);
struct fe_priv *np = get_nvpriv(dev);
- u8 __iomem *base = get_hwbase(dev);
unregister_netdev(dev);
- /* special op: write back the misordered MAC address - otherwise
- * the next nv_probe would see a wrong address.
- */
- writel(np->orig_mac[0], base + NvRegMacAddrA);
- writel(np->orig_mac[1], base + NvRegMacAddrB);
-
/* free all structures */
- pci_free_consistent(np->pci_dev, sizeof(struct ring_desc) * (RX_RING + TX_RING), np->rx_ring, np->ring_addr);
+ if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2)
+ pci_free_consistent(np->pci_dev, sizeof(struct ring_desc) * (RX_RING + TX_RING), np->rx_ring.orig, np->ring_addr);
+ else
+ pci_free_consistent(np->pci_dev, sizeof(struct ring_desc_ex) * (RX_RING + TX_RING), np->rx_ring.ex, np->ring_addr);
iounmap(get_hwbase(dev));
pci_release_regions(pci_dev);
pci_disable_device(pci_dev);
@@ -2195,109 +2512,64 @@
static struct pci_device_id pci_tbl[] = {
{ /* nForce Ethernet Controller */
- .vendor = PCI_VENDOR_ID_NVIDIA,
- .device = PCI_DEVICE_ID_NVIDIA_NVENET_1,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .driver_data = DEV_IRQMASK_1|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER,
+ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_1),
+ .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER,
},
{ /* nForce2 Ethernet Controller */
- .vendor = PCI_VENDOR_ID_NVIDIA,
- .device = PCI_DEVICE_ID_NVIDIA_NVENET_2,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER,
+ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_2),
+ .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER,
},
{ /* nForce3 Ethernet Controller */
- .vendor = PCI_VENDOR_ID_NVIDIA,
- .device = PCI_DEVICE_ID_NVIDIA_NVENET_3,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER,
+ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_3),
+ .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER,
},
{ /* nForce3 Ethernet Controller */
- .vendor = PCI_VENDOR_ID_NVIDIA,
- .device = PCI_DEVICE_ID_NVIDIA_NVENET_4,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER,
+ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_4),
+ .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC,
},
{ /* nForce3 Ethernet Controller */
- .vendor = PCI_VENDOR_ID_NVIDIA,
- .device = PCI_DEVICE_ID_NVIDIA_NVENET_5,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER,
+ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_5),
+ .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC,
},
{ /* nForce3 Ethernet Controller */
- .vendor = PCI_VENDOR_ID_NVIDIA,
- .device = PCI_DEVICE_ID_NVIDIA_NVENET_6,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER,
+ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_6),
+ .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC,
},
{ /* nForce3 Ethernet Controller */
- .vendor = PCI_VENDOR_ID_NVIDIA,
- .device = PCI_DEVICE_ID_NVIDIA_NVENET_7,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER,
+ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_7),
+ .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC,
},
{ /* CK804 Ethernet Controller */
- .vendor = PCI_VENDOR_ID_NVIDIA,
- .device = PCI_DEVICE_ID_NVIDIA_NVENET_8,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER,
+ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_8),
+ .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC|DEV_HAS_HIGH_DMA,
},
{ /* CK804 Ethernet Controller */
- .vendor = PCI_VENDOR_ID_NVIDIA,
- .device = PCI_DEVICE_ID_NVIDIA_NVENET_9,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER,
+ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_9),
+ .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC|DEV_HAS_HIGH_DMA,
},
{ /* MCP04 Ethernet Controller */
- .vendor = PCI_VENDOR_ID_NVIDIA,
- .device = PCI_DEVICE_ID_NVIDIA_NVENET_10,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER,
+ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_10),
+ .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC|DEV_HAS_HIGH_DMA,
},
{ /* MCP04 Ethernet Controller */
- .vendor = PCI_VENDOR_ID_NVIDIA,
- .device = PCI_DEVICE_ID_NVIDIA_NVENET_11,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER,
+ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_11),
+ .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC|DEV_HAS_HIGH_DMA,
},
{ /* MCP51 Ethernet Controller */
- .vendor = PCI_VENDOR_ID_NVIDIA,
- .device = PCI_DEVICE_ID_NVIDIA_NVENET_12,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER,
+ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_12),
+ .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_HIGH_DMA,
},
{ /* MCP51 Ethernet Controller */
- .vendor = PCI_VENDOR_ID_NVIDIA,
- .device = PCI_DEVICE_ID_NVIDIA_NVENET_13,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER,
+ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_13),
+ .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_HIGH_DMA,
},
{ /* MCP55 Ethernet Controller */
- .vendor = PCI_VENDOR_ID_NVIDIA,
- .device = PCI_DEVICE_ID_NVIDIA_NVENET_14,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER,
+ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_14),
+ .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC|DEV_HAS_HIGH_DMA,
},
{ /* MCP55 Ethernet Controller */
- .vendor = PCI_VENDOR_ID_NVIDIA,
- .device = PCI_DEVICE_ID_NVIDIA_NVENET_15,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER,
+ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_15),
+ .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC|DEV_HAS_HIGH_DMA,
},
{0,},
};
diff --git a/drivers/net/hamradio/6pack.c b/drivers/net/hamradio/6pack.c
index f9e3be9..0b23022 100644
--- a/drivers/net/hamradio/6pack.c
+++ b/drivers/net/hamradio/6pack.c
@@ -308,12 +308,6 @@
{
struct sockaddr_ax25 *sa = addr;
- if (sa->sax25_family != AF_AX25)
- return -EINVAL;
-
- if (!sa->sax25_ndigis)
- return -EINVAL;
-
spin_lock_irq(&dev->xmit_lock);
memcpy(dev->dev_addr, &sa->sax25_call, AX25_ADDR_LEN);
spin_unlock_irq(&dev->xmit_lock);
@@ -668,6 +662,9 @@
netif_start_queue(dev);
init_timer(&sp->tx_t);
+ sp->tx_t.function = sp_xmit_on_air;
+ sp->tx_t.data = (unsigned long) sp;
+
init_timer(&sp->resync_t);
spin_unlock_bh(&sp->lock);
diff --git a/drivers/net/hamradio/Kconfig b/drivers/net/hamradio/Kconfig
index 0cd5430..de087cd 100644
--- a/drivers/net/hamradio/Kconfig
+++ b/drivers/net/hamradio/Kconfig
@@ -1,6 +1,6 @@
config MKISS
tristate "Serial port KISS driver"
- depends on AX25 && BROKEN_ON_SMP
+ depends on AX25
---help---
KISS is a protocol used for the exchange of data between a computer
and a Terminal Node Controller (a small embedded system commonly
diff --git a/drivers/net/hamradio/baycom_epp.c b/drivers/net/hamradio/baycom_epp.c
index a7f15d9..5298096 100644
--- a/drivers/net/hamradio/baycom_epp.c
+++ b/drivers/net/hamradio/baycom_epp.c
@@ -54,6 +54,7 @@
#include <linux/kmod.h>
#include <linux/hdlcdrv.h>
#include <linux/baycom.h>
+#include <linux/jiffies.h>
#if defined(CONFIG_AX25) || defined(CONFIG_AX25_MODULE)
/* prototypes for ax25_encapsulate and ax25_rebuild_header */
#include <net/ax25.h>
@@ -287,7 +288,7 @@
* measure the interrupt frequency
*/
bc->debug_vals.cur_intcnt++;
- if ((cur_jiffies - bc->debug_vals.last_jiffies) >= HZ) {
+ if (time_after_eq(cur_jiffies, bc->debug_vals.last_jiffies + HZ)) {
bc->debug_vals.last_jiffies = cur_jiffies;
bc->debug_vals.last_intcnt = bc->debug_vals.cur_intcnt;
bc->debug_vals.cur_intcnt = 0;
diff --git a/drivers/net/hamradio/baycom_par.c b/drivers/net/hamradio/baycom_par.c
index 612ad45..3b1bef1 100644
--- a/drivers/net/hamradio/baycom_par.c
+++ b/drivers/net/hamradio/baycom_par.c
@@ -84,6 +84,7 @@
#include <linux/baycom.h>
#include <linux/parport.h>
#include <linux/bitops.h>
+#include <linux/jiffies.h>
#include <asm/bug.h>
#include <asm/system.h>
@@ -165,7 +166,7 @@
* measure the interrupt frequency
*/
bc->debug_vals.cur_intcnt++;
- if ((cur_jiffies - bc->debug_vals.last_jiffies) >= HZ) {
+ if (time_after_eq(cur_jiffies, bc->debug_vals.last_jiffies + HZ)) {
bc->debug_vals.last_jiffies = cur_jiffies;
bc->debug_vals.last_intcnt = bc->debug_vals.cur_intcnt;
bc->debug_vals.cur_intcnt = 0;
diff --git a/drivers/net/hamradio/baycom_ser_fdx.c b/drivers/net/hamradio/baycom_ser_fdx.c
index 25f270b..232793d 100644
--- a/drivers/net/hamradio/baycom_ser_fdx.c
+++ b/drivers/net/hamradio/baycom_ser_fdx.c
@@ -79,6 +79,7 @@
#include <asm/io.h>
#include <linux/hdlcdrv.h>
#include <linux/baycom.h>
+#include <linux/jiffies.h>
/* --------------------------------------------------------------------- */
@@ -159,7 +160,7 @@
* measure the interrupt frequency
*/
bc->debug_vals.cur_intcnt++;
- if ((cur_jiffies - bc->debug_vals.last_jiffies) >= HZ) {
+ if (time_after_eq(cur_jiffies, bc->debug_vals.last_jiffies + HZ)) {
bc->debug_vals.last_jiffies = cur_jiffies;
bc->debug_vals.last_intcnt = bc->debug_vals.cur_intcnt;
bc->debug_vals.cur_intcnt = 0;
diff --git a/drivers/net/hamradio/baycom_ser_hdx.c b/drivers/net/hamradio/baycom_ser_hdx.c
index eead85d..be596a3 100644
--- a/drivers/net/hamradio/baycom_ser_hdx.c
+++ b/drivers/net/hamradio/baycom_ser_hdx.c
@@ -69,6 +69,7 @@
#include <asm/io.h>
#include <linux/hdlcdrv.h>
#include <linux/baycom.h>
+#include <linux/jiffies.h>
/* --------------------------------------------------------------------- */
@@ -150,7 +151,7 @@
* measure the interrupt frequency
*/
bc->debug_vals.cur_intcnt++;
- if ((cur_jiffies - bc->debug_vals.last_jiffies) >= HZ) {
+ if (time_after_eq(cur_jiffies, bc->debug_vals.last_jiffies + HZ)) {
bc->debug_vals.last_jiffies = cur_jiffies;
bc->debug_vals.last_intcnt = bc->debug_vals.cur_intcnt;
bc->debug_vals.cur_intcnt = 0;
diff --git a/drivers/net/hamradio/mkiss.c b/drivers/net/hamradio/mkiss.c
index 3035422..63b1a2b 100644
--- a/drivers/net/hamradio/mkiss.c
+++ b/drivers/net/hamradio/mkiss.c
@@ -1,30 +1,19 @@
/*
- * MKISS Driver
+ * This program is free software; you can distribute it and/or modify it
+ * under the terms of the GNU General Public License (Version 2) as
+ * published by the Free Software Foundation.
*
- * This module:
- * This module is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version
- * 2 of the License, or (at your option) any later version.
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ * for more details.
*
- * This module implements the AX.25 protocol for kernel-based
- * devices like TTYs. It interfaces between a raw TTY, and the
- * kernel's AX.25 protocol layers, just like slip.c.
- * AX.25 needs to be separated from slip.c while slip.c is no
- * longer a static kernel device since it is a module.
- * This method clears the way to implement other kiss protocols
- * like mkiss smack g8bpq ..... so far only mkiss is implemented.
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
*
- * Hans Alblas <hans@esrac.ele.tue.nl>
- *
- * History
- * Jonathan (G4KLX) Fixed to match Linux networking changes - 2.1.15.
- * Matthias (DG2FEF) Added support for FlexNet CRC (on special request)
- * Fixed bug in ax25_close(): dev_lock_wait() was
- * called twice, causing a deadlock.
- * Jeroen (PE1RXQ) Removed old MKISS_MAGIC stuff and calls to
- * MOD_*_USE_COUNT
- * Remove cli() and fix rtnl lock usage.
+ * Copyright (C) Hans Alblas PE1AYX <hans@esrac.ele.tue.nl>
+ * Copyright (C) 2004, 05 Ralf Baechle DL5RB <ralf@linux-mips.org>
*/
#include <linux/config.h>
@@ -46,177 +35,300 @@
#include <linux/etherdevice.h>
#include <linux/skbuff.h>
#include <linux/if_arp.h>
+#include <linux/jiffies.h>
#include <net/ax25.h>
-#include "mkiss.h"
-
#ifdef CONFIG_INET
#include <linux/ip.h>
#include <linux/tcp.h>
#endif
-static char banner[] __initdata = KERN_INFO "mkiss: AX.25 Multikiss, Hans Albas PE1AYX\n";
+#define AX_MTU 236
-typedef struct ax25_ctrl {
- struct ax_disp ctrl; /* */
- struct net_device dev; /* the device */
-} ax25_ctrl_t;
+/* SLIP/KISS protocol characters. */
+#define END 0300 /* indicates end of frame */
+#define ESC 0333 /* indicates byte stuffing */
+#define ESC_END 0334 /* ESC ESC_END means END 'data' */
+#define ESC_ESC 0335 /* ESC ESC_ESC means ESC 'data' */
-static ax25_ctrl_t **ax25_ctrls;
+struct mkiss {
+ struct tty_struct *tty; /* ptr to TTY structure */
+ struct net_device *dev; /* easy for intr handling */
-int ax25_maxdev = AX25_MAXDEV; /* Can be overridden with insmod! */
+ /* These are pointers to the malloc()ed frame buffers. */
+ spinlock_t buflock;/* lock for rbuf and xbuf */
+ unsigned char *rbuff; /* receiver buffer */
+ int rcount; /* received chars counter */
+ unsigned char *xbuff; /* transmitter buffer */
+ unsigned char *xhead; /* pointer to next byte to XMIT */
+ int xleft; /* bytes left in XMIT queue */
-static struct tty_ldisc ax_ldisc;
+ struct net_device_stats stats;
-static int ax25_init(struct net_device *);
-static int kiss_esc(unsigned char *, unsigned char *, int);
-static int kiss_esc_crc(unsigned char *, unsigned char *, unsigned short, int);
-static void kiss_unesc(struct ax_disp *, unsigned char);
+ /* Detailed SLIP statistics. */
+ int mtu; /* Our mtu (to spot changes!) */
+ int buffsize; /* Max buffers sizes */
-/*---------------------------------------------------------------------------*/
+ unsigned long flags; /* Flag values/ mode etc */
+ /* long req'd: used by set_bit --RR */
+#define AXF_INUSE 0 /* Channel in use */
+#define AXF_ESCAPE 1 /* ESC received */
+#define AXF_ERROR 2 /* Parity, etc. error */
+#define AXF_KEEPTEST 3 /* Keepalive test flag */
+#define AXF_OUTWAIT 4 /* is outpacket was flag */
-static const unsigned short Crc_flex_table[] = {
- 0x0f87, 0x1e0e, 0x2c95, 0x3d1c, 0x49a3, 0x582a, 0x6ab1, 0x7b38,
- 0x83cf, 0x9246, 0xa0dd, 0xb154, 0xc5eb, 0xd462, 0xe6f9, 0xf770,
- 0x1f06, 0x0e8f, 0x3c14, 0x2d9d, 0x5922, 0x48ab, 0x7a30, 0x6bb9,
- 0x934e, 0x82c7, 0xb05c, 0xa1d5, 0xd56a, 0xc4e3, 0xf678, 0xe7f1,
- 0x2e85, 0x3f0c, 0x0d97, 0x1c1e, 0x68a1, 0x7928, 0x4bb3, 0x5a3a,
- 0xa2cd, 0xb344, 0x81df, 0x9056, 0xe4e9, 0xf560, 0xc7fb, 0xd672,
- 0x3e04, 0x2f8d, 0x1d16, 0x0c9f, 0x7820, 0x69a9, 0x5b32, 0x4abb,
- 0xb24c, 0xa3c5, 0x915e, 0x80d7, 0xf468, 0xe5e1, 0xd77a, 0xc6f3,
- 0x4d83, 0x5c0a, 0x6e91, 0x7f18, 0x0ba7, 0x1a2e, 0x28b5, 0x393c,
- 0xc1cb, 0xd042, 0xe2d9, 0xf350, 0x87ef, 0x9666, 0xa4fd, 0xb574,
- 0x5d02, 0x4c8b, 0x7e10, 0x6f99, 0x1b26, 0x0aaf, 0x3834, 0x29bd,
- 0xd14a, 0xc0c3, 0xf258, 0xe3d1, 0x976e, 0x86e7, 0xb47c, 0xa5f5,
- 0x6c81, 0x7d08, 0x4f93, 0x5e1a, 0x2aa5, 0x3b2c, 0x09b7, 0x183e,
- 0xe0c9, 0xf140, 0xc3db, 0xd252, 0xa6ed, 0xb764, 0x85ff, 0x9476,
- 0x7c00, 0x6d89, 0x5f12, 0x4e9b, 0x3a24, 0x2bad, 0x1936, 0x08bf,
- 0xf048, 0xe1c1, 0xd35a, 0xc2d3, 0xb66c, 0xa7e5, 0x957e, 0x84f7,
- 0x8b8f, 0x9a06, 0xa89d, 0xb914, 0xcdab, 0xdc22, 0xeeb9, 0xff30,
- 0x07c7, 0x164e, 0x24d5, 0x355c, 0x41e3, 0x506a, 0x62f1, 0x7378,
- 0x9b0e, 0x8a87, 0xb81c, 0xa995, 0xdd2a, 0xcca3, 0xfe38, 0xefb1,
- 0x1746, 0x06cf, 0x3454, 0x25dd, 0x5162, 0x40eb, 0x7270, 0x63f9,
- 0xaa8d, 0xbb04, 0x899f, 0x9816, 0xeca9, 0xfd20, 0xcfbb, 0xde32,
- 0x26c5, 0x374c, 0x05d7, 0x145e, 0x60e1, 0x7168, 0x43f3, 0x527a,
- 0xba0c, 0xab85, 0x991e, 0x8897, 0xfc28, 0xeda1, 0xdf3a, 0xceb3,
- 0x3644, 0x27cd, 0x1556, 0x04df, 0x7060, 0x61e9, 0x5372, 0x42fb,
- 0xc98b, 0xd802, 0xea99, 0xfb10, 0x8faf, 0x9e26, 0xacbd, 0xbd34,
- 0x45c3, 0x544a, 0x66d1, 0x7758, 0x03e7, 0x126e, 0x20f5, 0x317c,
- 0xd90a, 0xc883, 0xfa18, 0xeb91, 0x9f2e, 0x8ea7, 0xbc3c, 0xadb5,
- 0x5542, 0x44cb, 0x7650, 0x67d9, 0x1366, 0x02ef, 0x3074, 0x21fd,
- 0xe889, 0xf900, 0xcb9b, 0xda12, 0xaead, 0xbf24, 0x8dbf, 0x9c36,
- 0x64c1, 0x7548, 0x47d3, 0x565a, 0x22e5, 0x336c, 0x01f7, 0x107e,
- 0xf808, 0xe981, 0xdb1a, 0xca93, 0xbe2c, 0xafa5, 0x9d3e, 0x8cb7,
- 0x7440, 0x65c9, 0x5752, 0x46db, 0x3264, 0x23ed, 0x1176, 0x00ff
+ int mode;
+ int crcmode; /* MW: for FlexNet, SMACK etc. */
+#define CRC_MODE_NONE 0
+#define CRC_MODE_FLEX 1
+#define CRC_MODE_SMACK 2
+
+ atomic_t refcnt;
+ struct semaphore dead_sem;
};
/*---------------------------------------------------------------------------*/
+static const unsigned short crc_flex_table[] = {
+ 0x0f87, 0x1e0e, 0x2c95, 0x3d1c, 0x49a3, 0x582a, 0x6ab1, 0x7b38,
+ 0x83cf, 0x9246, 0xa0dd, 0xb154, 0xc5eb, 0xd462, 0xe6f9, 0xf770,
+ 0x1f06, 0x0e8f, 0x3c14, 0x2d9d, 0x5922, 0x48ab, 0x7a30, 0x6bb9,
+ 0x934e, 0x82c7, 0xb05c, 0xa1d5, 0xd56a, 0xc4e3, 0xf678, 0xe7f1,
+ 0x2e85, 0x3f0c, 0x0d97, 0x1c1e, 0x68a1, 0x7928, 0x4bb3, 0x5a3a,
+ 0xa2cd, 0xb344, 0x81df, 0x9056, 0xe4e9, 0xf560, 0xc7fb, 0xd672,
+ 0x3e04, 0x2f8d, 0x1d16, 0x0c9f, 0x7820, 0x69a9, 0x5b32, 0x4abb,
+ 0xb24c, 0xa3c5, 0x915e, 0x80d7, 0xf468, 0xe5e1, 0xd77a, 0xc6f3,
+ 0x4d83, 0x5c0a, 0x6e91, 0x7f18, 0x0ba7, 0x1a2e, 0x28b5, 0x393c,
+ 0xc1cb, 0xd042, 0xe2d9, 0xf350, 0x87ef, 0x9666, 0xa4fd, 0xb574,
+ 0x5d02, 0x4c8b, 0x7e10, 0x6f99, 0x1b26, 0x0aaf, 0x3834, 0x29bd,
+ 0xd14a, 0xc0c3, 0xf258, 0xe3d1, 0x976e, 0x86e7, 0xb47c, 0xa5f5,
+ 0x6c81, 0x7d08, 0x4f93, 0x5e1a, 0x2aa5, 0x3b2c, 0x09b7, 0x183e,
+ 0xe0c9, 0xf140, 0xc3db, 0xd252, 0xa6ed, 0xb764, 0x85ff, 0x9476,
+ 0x7c00, 0x6d89, 0x5f12, 0x4e9b, 0x3a24, 0x2bad, 0x1936, 0x08bf,
+ 0xf048, 0xe1c1, 0xd35a, 0xc2d3, 0xb66c, 0xa7e5, 0x957e, 0x84f7,
+ 0x8b8f, 0x9a06, 0xa89d, 0xb914, 0xcdab, 0xdc22, 0xeeb9, 0xff30,
+ 0x07c7, 0x164e, 0x24d5, 0x355c, 0x41e3, 0x506a, 0x62f1, 0x7378,
+ 0x9b0e, 0x8a87, 0xb81c, 0xa995, 0xdd2a, 0xcca3, 0xfe38, 0xefb1,
+ 0x1746, 0x06cf, 0x3454, 0x25dd, 0x5162, 0x40eb, 0x7270, 0x63f9,
+ 0xaa8d, 0xbb04, 0x899f, 0x9816, 0xeca9, 0xfd20, 0xcfbb, 0xde32,
+ 0x26c5, 0x374c, 0x05d7, 0x145e, 0x60e1, 0x7168, 0x43f3, 0x527a,
+ 0xba0c, 0xab85, 0x991e, 0x8897, 0xfc28, 0xeda1, 0xdf3a, 0xceb3,
+ 0x3644, 0x27cd, 0x1556, 0x04df, 0x7060, 0x61e9, 0x5372, 0x42fb,
+ 0xc98b, 0xd802, 0xea99, 0xfb10, 0x8faf, 0x9e26, 0xacbd, 0xbd34,
+ 0x45c3, 0x544a, 0x66d1, 0x7758, 0x03e7, 0x126e, 0x20f5, 0x317c,
+ 0xd90a, 0xc883, 0xfa18, 0xeb91, 0x9f2e, 0x8ea7, 0xbc3c, 0xadb5,
+ 0x5542, 0x44cb, 0x7650, 0x67d9, 0x1366, 0x02ef, 0x3074, 0x21fd,
+ 0xe889, 0xf900, 0xcb9b, 0xda12, 0xaead, 0xbf24, 0x8dbf, 0x9c36,
+ 0x64c1, 0x7548, 0x47d3, 0x565a, 0x22e5, 0x336c, 0x01f7, 0x107e,
+ 0xf808, 0xe981, 0xdb1a, 0xca93, 0xbe2c, 0xafa5, 0x9d3e, 0x8cb7,
+ 0x7440, 0x65c9, 0x5752, 0x46db, 0x3264, 0x23ed, 0x1176, 0x00ff
+};
+
static unsigned short calc_crc_flex(unsigned char *cp, int size)
{
- unsigned short crc = 0xffff;
-
- while (size--)
- crc = (crc << 8) ^ Crc_flex_table[((crc >> 8) ^ *cp++) & 0xff];
+ unsigned short crc = 0xffff;
- return crc;
+ while (size--)
+ crc = (crc << 8) ^ crc_flex_table[((crc >> 8) ^ *cp++) & 0xff];
+
+ return crc;
}
-/*---------------------------------------------------------------------------*/
-
static int check_crc_flex(unsigned char *cp, int size)
{
- unsigned short crc = 0xffff;
+ unsigned short crc = 0xffff;
- if (size < 3)
- return -1;
+ if (size < 3)
+ return -1;
- while (size--)
- crc = (crc << 8) ^ Crc_flex_table[((crc >> 8) ^ *cp++) & 0xff];
+ while (size--)
+ crc = (crc << 8) ^ crc_flex_table[((crc >> 8) ^ *cp++) & 0xff];
- if ((crc & 0xffff) != 0x7070)
- return -1;
+ if ((crc & 0xffff) != 0x7070)
+ return -1;
- return 0;
+ return 0;
+}
+
+/*
+ * Standard encapsulation
+ */
+
+static int kiss_esc(unsigned char *s, unsigned char *d, int len)
+{
+ unsigned char *ptr = d;
+ unsigned char c;
+
+ /*
+ * Send an initial END character to flush out any data that may have
+ * accumulated in the receiver due to line noise.
+ */
+
+ *ptr++ = END;
+
+ while (len-- > 0) {
+ switch (c = *s++) {
+ case END:
+ *ptr++ = ESC;
+ *ptr++ = ESC_END;
+ break;
+ case ESC:
+ *ptr++ = ESC;
+ *ptr++ = ESC_ESC;
+ break;
+ default:
+ *ptr++ = c;
+ break;
+ }
+ }
+
+ *ptr++ = END;
+
+ return ptr - d;
+}
+
+/*
+ * MW:
+ * OK its ugly, but tell me a better solution without copying the
+ * packet to a temporary buffer :-)
+ */
+static int kiss_esc_crc(unsigned char *s, unsigned char *d, unsigned short crc,
+ int len)
+{
+ unsigned char *ptr = d;
+ unsigned char c=0;
+
+ *ptr++ = END;
+ while (len > 0) {
+ if (len > 2)
+ c = *s++;
+ else if (len > 1)
+ c = crc >> 8;
+ else if (len > 0)
+ c = crc & 0xff;
+
+ len--;
+
+ switch (c) {
+ case END:
+ *ptr++ = ESC;
+ *ptr++ = ESC_END;
+ break;
+ case ESC:
+ *ptr++ = ESC;
+ *ptr++ = ESC_ESC;
+ break;
+ default:
+ *ptr++ = c;
+ break;
+ }
+ }
+ *ptr++ = END;
+
+ return ptr - d;
+}
+
+/* Send one completely decapsulated AX.25 packet to the AX.25 layer. */
+static void ax_bump(struct mkiss *ax)
+{
+ struct sk_buff *skb;
+ int count;
+
+ spin_lock_bh(&ax->buflock);
+ if (ax->rbuff[0] > 0x0f) {
+ if (ax->rbuff[0] & 0x20) {
+ ax->crcmode = CRC_MODE_FLEX;
+ if (check_crc_flex(ax->rbuff, ax->rcount) < 0) {
+ ax->stats.rx_errors++;
+ return;
+ }
+ ax->rcount -= 2;
+ /* dl9sau bugfix: the trailling two bytes flexnet crc
+ * will not be passed to the kernel. thus we have
+ * to correct the kissparm signature, because it
+ * indicates a crc but there's none
+ */
+ *ax->rbuff &= ~0x20;
+ }
+ }
+ spin_unlock_bh(&ax->buflock);
+
+ count = ax->rcount;
+
+ if ((skb = dev_alloc_skb(count)) == NULL) {
+ printk(KERN_ERR "mkiss: %s: memory squeeze, dropping packet.\n",
+ ax->dev->name);
+ ax->stats.rx_dropped++;
+ return;
+ }
+
+ spin_lock_bh(&ax->buflock);
+ memcpy(skb_put(skb,count), ax->rbuff, count);
+ spin_unlock_bh(&ax->buflock);
+ skb->protocol = ax25_type_trans(skb, ax->dev);
+ netif_rx(skb);
+ ax->dev->last_rx = jiffies;
+ ax->stats.rx_packets++;
+ ax->stats.rx_bytes += count;
+}
+
+static void kiss_unesc(struct mkiss *ax, unsigned char s)
+{
+ switch (s) {
+ case END:
+ /* drop keeptest bit = VSV */
+ if (test_bit(AXF_KEEPTEST, &ax->flags))
+ clear_bit(AXF_KEEPTEST, &ax->flags);
+
+ if (!test_and_clear_bit(AXF_ERROR, &ax->flags) && (ax->rcount > 2))
+ ax_bump(ax);
+
+ clear_bit(AXF_ESCAPE, &ax->flags);
+ ax->rcount = 0;
+ return;
+
+ case ESC:
+ set_bit(AXF_ESCAPE, &ax->flags);
+ return;
+ case ESC_ESC:
+ if (test_and_clear_bit(AXF_ESCAPE, &ax->flags))
+ s = ESC;
+ break;
+ case ESC_END:
+ if (test_and_clear_bit(AXF_ESCAPE, &ax->flags))
+ s = END;
+ break;
+ }
+
+ spin_lock_bh(&ax->buflock);
+ if (!test_bit(AXF_ERROR, &ax->flags)) {
+ if (ax->rcount < ax->buffsize) {
+ ax->rbuff[ax->rcount++] = s;
+ spin_unlock_bh(&ax->buflock);
+ return;
+ }
+
+ ax->stats.rx_over_errors++;
+ set_bit(AXF_ERROR, &ax->flags);
+ }
+ spin_unlock_bh(&ax->buflock);
+}
+
+static int ax_set_mac_address(struct net_device *dev, void *addr)
+{
+ struct sockaddr_ax25 *sa = addr;
+
+ spin_lock_irq(&dev->xmit_lock);
+ memcpy(dev->dev_addr, &sa->sax25_call, AX25_ADDR_LEN);
+ spin_unlock_irq(&dev->xmit_lock);
+
+ return 0;
}
/*---------------------------------------------------------------------------*/
-/* Find a free channel, and link in this `tty' line. */
-static inline struct ax_disp *ax_alloc(void)
-{
- ax25_ctrl_t *axp=NULL;
- int i;
-
- for (i = 0; i < ax25_maxdev; i++) {
- axp = ax25_ctrls[i];
-
- /* Not allocated ? */
- if (axp == NULL)
- break;
-
- /* Not in use ? */
- if (!test_and_set_bit(AXF_INUSE, &axp->ctrl.flags))
- break;
- }
-
- /* Sorry, too many, all slots in use */
- if (i >= ax25_maxdev)
- return NULL;
-
- /* If no channels are available, allocate one */
- if (axp == NULL && (ax25_ctrls[i] = kmalloc(sizeof(ax25_ctrl_t), GFP_KERNEL)) != NULL) {
- axp = ax25_ctrls[i];
- }
- memset(axp, 0, sizeof(ax25_ctrl_t));
-
- /* Initialize channel control data */
- set_bit(AXF_INUSE, &axp->ctrl.flags);
- sprintf(axp->dev.name, "ax%d", i++);
- axp->ctrl.tty = NULL;
- axp->dev.base_addr = i;
- axp->dev.priv = (void *)&axp->ctrl;
- axp->dev.next = NULL;
- axp->dev.init = ax25_init;
-
- if (axp != NULL) {
- /*
- * register device so that it can be ifconfig'ed
- * ax25_init() will be called as a side-effect
- * SIDE-EFFECT WARNING: ax25_init() CLEARS axp->ctrl !
- */
- if (register_netdev(&axp->dev) == 0) {
- /* (Re-)Set the INUSE bit. Very Important! */
- set_bit(AXF_INUSE, &axp->ctrl.flags);
- axp->ctrl.dev = &axp->dev;
- axp->dev.priv = (void *) &axp->ctrl;
-
- return &axp->ctrl;
- } else {
- clear_bit(AXF_INUSE,&axp->ctrl.flags);
- printk(KERN_ERR "mkiss: ax_alloc() - register_netdev() failure.\n");
- }
- }
-
- return NULL;
-}
-
-/* Free an AX25 channel. */
-static inline void ax_free(struct ax_disp *ax)
-{
- /* Free all AX25 frame buffers. */
- if (ax->rbuff)
- kfree(ax->rbuff);
- ax->rbuff = NULL;
- if (ax->xbuff)
- kfree(ax->xbuff);
- ax->xbuff = NULL;
- if (!test_and_clear_bit(AXF_INUSE, &ax->flags))
- printk(KERN_ERR "mkiss: %s: ax_free for already free unit.\n", ax->dev->name);
-}
-
-static void ax_changedmtu(struct ax_disp *ax)
+static void ax_changedmtu(struct mkiss *ax)
{
struct net_device *dev = ax->dev;
unsigned char *xbuff, *rbuff, *oxbuff, *orbuff;
@@ -236,7 +348,8 @@
rbuff = kmalloc(len + 4, GFP_ATOMIC);
if (xbuff == NULL || rbuff == NULL) {
- printk(KERN_ERR "mkiss: %s: unable to grow ax25 buffers, MTU change cancelled.\n",
+ printk(KERN_ERR "mkiss: %s: unable to grow ax25 buffers, "
+ "MTU change cancelled.\n",
ax->dev->name);
dev->mtu = ax->mtu;
if (xbuff != NULL)
@@ -258,7 +371,7 @@
memcpy(ax->xbuff, ax->xhead, ax->xleft);
} else {
ax->xleft = 0;
- ax->tx_dropped++;
+ ax->stats.tx_dropped++;
}
}
@@ -269,7 +382,7 @@
memcpy(ax->rbuff, orbuff, ax->rcount);
} else {
ax->rcount = 0;
- ax->rx_over_errors++;
+ ax->stats.rx_over_errors++;
set_bit(AXF_ERROR, &ax->flags);
}
}
@@ -279,72 +392,14 @@
spin_unlock_bh(&ax->buflock);
- if (oxbuff != NULL)
- kfree(oxbuff);
- if (orbuff != NULL)
- kfree(orbuff);
-}
-
-
-/* Set the "sending" flag. This must be atomic. */
-static inline void ax_lock(struct ax_disp *ax)
-{
- netif_stop_queue(ax->dev);
-}
-
-
-/* Clear the "sending" flag. This must be atomic. */
-static inline void ax_unlock(struct ax_disp *ax)
-{
- netif_start_queue(ax->dev);
-}
-
-/* Send one completely decapsulated AX.25 packet to the AX.25 layer. */
-static void ax_bump(struct ax_disp *ax)
-{
- struct sk_buff *skb;
- int count;
-
- spin_lock_bh(&ax->buflock);
- if (ax->rbuff[0] > 0x0f) {
- if (ax->rbuff[0] & 0x20) {
- ax->crcmode = CRC_MODE_FLEX;
- if (check_crc_flex(ax->rbuff, ax->rcount) < 0) {
- ax->rx_errors++;
- return;
- }
- ax->rcount -= 2;
- /* dl9sau bugfix: the trailling two bytes flexnet crc
- * will not be passed to the kernel. thus we have
- * to correct the kissparm signature, because it
- * indicates a crc but there's none
- */
- *ax->rbuff &= ~0x20;
- }
- }
- spin_unlock_bh(&ax->buflock);
-
- count = ax->rcount;
-
- if ((skb = dev_alloc_skb(count)) == NULL) {
- printk(KERN_ERR "mkiss: %s: memory squeeze, dropping packet.\n", ax->dev->name);
- ax->rx_dropped++;
- return;
- }
-
- spin_lock_bh(&ax->buflock);
- memcpy(skb_put(skb,count), ax->rbuff, count);
- spin_unlock_bh(&ax->buflock);
- skb->protocol = ax25_type_trans(skb, ax->dev);
- netif_rx(skb);
- ax->dev->last_rx = jiffies;
- ax->rx_packets++;
- ax->rx_bytes+=count;
+ kfree(oxbuff);
+ kfree(orbuff);
}
/* Encapsulate one AX.25 packet and stuff into a TTY queue. */
-static void ax_encaps(struct ax_disp *ax, unsigned char *icp, int len)
+static void ax_encaps(struct net_device *dev, unsigned char *icp, int len)
{
+ struct mkiss *ax = netdev_priv(dev);
unsigned char *p;
int actual, count;
@@ -354,8 +409,8 @@
if (len > ax->mtu) { /* Sigh, shouldn't occur BUT ... */
len = ax->mtu;
printk(KERN_ERR "mkiss: %s: truncating oversized transmit packet!\n", ax->dev->name);
- ax->tx_dropped++;
- ax_unlock(ax);
+ ax->stats.tx_dropped++;
+ netif_start_queue(dev);
return;
}
@@ -376,10 +431,11 @@
break;
}
- ax->tty->flags |= (1 << TTY_DO_WRITE_WAKEUP);
+ set_bit(TTY_DO_WRITE_WAKEUP, &ax->tty->flags);
actual = ax->tty->driver->write(ax->tty, ax->xbuff, count);
- ax->tx_packets++;
- ax->tx_bytes+=actual;
+ ax->stats.tx_packets++;
+ ax->stats.tx_bytes += actual;
+
ax->dev->trans_start = jiffies;
ax->xleft = count - actual;
ax->xhead = ax->xbuff + actual;
@@ -387,37 +443,10 @@
spin_unlock_bh(&ax->buflock);
}
-/*
- * Called by the driver when there's room for more data. If we have
- * more packets to send, we send them here.
- */
-static void ax25_write_wakeup(struct tty_struct *tty)
-{
- int actual;
- struct ax_disp *ax = (struct ax_disp *) tty->disc_data;
-
- /* First make sure we're connected. */
- if (ax == NULL || ax->magic != AX25_MAGIC || !netif_running(ax->dev))
- return;
- if (ax->xleft <= 0) {
- /* Now serial buffer is almost free & we can start
- * transmission of another packet
- */
- tty->flags &= ~(1 << TTY_DO_WRITE_WAKEUP);
-
- netif_wake_queue(ax->dev);
- return;
- }
-
- actual = tty->driver->write(tty, ax->xhead, ax->xleft);
- ax->xleft -= actual;
- ax->xhead += actual;
-}
-
/* Encapsulate an AX.25 packet and kick it into a TTY queue. */
static int ax_xmit(struct sk_buff *skb, struct net_device *dev)
{
- struct ax_disp *ax = netdev_priv(dev);
+ struct mkiss *ax = netdev_priv(dev);
if (!netif_running(dev)) {
printk(KERN_ERR "mkiss: %s: xmit call when iface is down\n", dev->name);
@@ -429,7 +458,7 @@
* May be we must check transmitter timeout here ?
* 14 Oct 1994 Dmitry Gorodchanin.
*/
- if (jiffies - dev->trans_start < 20 * HZ) {
+ if (time_before(jiffies, dev->trans_start + 20 * HZ)) {
/* 20 sec timeout not reached */
return 1;
}
@@ -439,20 +468,30 @@
"bad line quality" : "driver error");
ax->xleft = 0;
- ax->tty->flags &= ~(1 << TTY_DO_WRITE_WAKEUP);
- ax_unlock(ax);
+ clear_bit(TTY_DO_WRITE_WAKEUP, &ax->tty->flags);
+ netif_start_queue(dev);
}
/* We were not busy, so we are now... :-) */
if (skb != NULL) {
- ax_lock(ax);
- ax_encaps(ax, skb->data, skb->len);
+ netif_stop_queue(dev);
+ ax_encaps(dev, skb->data, skb->len);
kfree_skb(skb);
}
return 0;
}
+static int ax_open_dev(struct net_device *dev)
+{
+ struct mkiss *ax = netdev_priv(dev);
+
+ if (ax->tty == NULL)
+ return -ENODEV;
+
+ return 0;
+}
+
#if defined(CONFIG_AX25) || defined(CONFIG_AX25_MODULE)
/* Return the frame type ID */
@@ -481,7 +520,7 @@
/* Open the low-level part of the AX25 channel. Easy! */
static int ax_open(struct net_device *dev)
{
- struct ax_disp *ax = netdev_priv(dev);
+ struct mkiss *ax = netdev_priv(dev);
unsigned long len;
if (ax->tty == NULL)
@@ -518,7 +557,6 @@
spin_lock_init(&ax->buflock);
- netif_start_queue(dev);
return 0;
noxbuff:
@@ -532,21 +570,223 @@
/* Close the low-level part of the AX25 channel. Easy! */
static int ax_close(struct net_device *dev)
{
- struct ax_disp *ax = netdev_priv(dev);
+ struct mkiss *ax = netdev_priv(dev);
- if (ax->tty == NULL)
- return -EBUSY;
-
- ax->tty->flags &= ~(1 << TTY_DO_WRITE_WAKEUP);
+ if (ax->tty)
+ clear_bit(TTY_DO_WRITE_WAKEUP, &ax->tty->flags);
netif_stop_queue(dev);
return 0;
}
-static int ax25_receive_room(struct tty_struct *tty)
+static struct net_device_stats *ax_get_stats(struct net_device *dev)
{
- return 65536; /* We can handle an infinite amount of data. :-) */
+ struct mkiss *ax = netdev_priv(dev);
+
+ return &ax->stats;
+}
+
+static void ax_setup(struct net_device *dev)
+{
+ static char ax25_bcast[AX25_ADDR_LEN] =
+ {'Q'<<1,'S'<<1,'T'<<1,' '<<1,' '<<1,' '<<1,'0'<<1};
+ static char ax25_test[AX25_ADDR_LEN] =
+ {'L'<<1,'I'<<1,'N'<<1,'U'<<1,'X'<<1,' '<<1,'1'<<1};
+
+ /* Finish setting up the DEVICE info. */
+ dev->mtu = AX_MTU;
+ dev->hard_start_xmit = ax_xmit;
+ dev->open = ax_open_dev;
+ dev->stop = ax_close;
+ dev->get_stats = ax_get_stats;
+ dev->set_mac_address = ax_set_mac_address;
+ dev->hard_header_len = 0;
+ dev->addr_len = 0;
+ dev->type = ARPHRD_AX25;
+ dev->tx_queue_len = 10;
+ dev->hard_header = ax_header;
+ dev->rebuild_header = ax_rebuild_header;
+
+ memcpy(dev->broadcast, ax25_bcast, AX25_ADDR_LEN);
+ memcpy(dev->dev_addr, ax25_test, AX25_ADDR_LEN);
+
+ dev->flags = IFF_BROADCAST | IFF_MULTICAST;
+}
+
+/*
+ * We have a potential race on dereferencing tty->disc_data, because the tty
+ * layer provides no locking at all - thus one cpu could be running
+ * sixpack_receive_buf while another calls sixpack_close, which zeroes
+ * tty->disc_data and frees the memory that sixpack_receive_buf is using. The
+ * best way to fix this is to use a rwlock in the tty struct, but for now we
+ * use a single global rwlock for all ttys in ppp line discipline.
+ */
+static rwlock_t disc_data_lock = RW_LOCK_UNLOCKED;
+
+static struct mkiss *mkiss_get(struct tty_struct *tty)
+{
+ struct mkiss *ax;
+
+ read_lock(&disc_data_lock);
+ ax = tty->disc_data;
+ if (ax)
+ atomic_inc(&ax->refcnt);
+ read_unlock(&disc_data_lock);
+
+ return ax;
+}
+
+static void mkiss_put(struct mkiss *ax)
+{
+ if (atomic_dec_and_test(&ax->refcnt))
+ up(&ax->dead_sem);
+}
+
+static int mkiss_open(struct tty_struct *tty)
+{
+ struct net_device *dev;
+ struct mkiss *ax;
+ int err;
+
+ if (!capable(CAP_NET_ADMIN))
+ return -EPERM;
+
+ dev = alloc_netdev(sizeof(struct mkiss), "ax%d", ax_setup);
+ if (!dev) {
+ err = -ENOMEM;
+ goto out;
+ }
+
+ ax = netdev_priv(dev);
+ ax->dev = dev;
+
+ spin_lock_init(&ax->buflock);
+ atomic_set(&ax->refcnt, 1);
+ init_MUTEX_LOCKED(&ax->dead_sem);
+
+ ax->tty = tty;
+ tty->disc_data = ax;
+
+ if (tty->driver->flush_buffer)
+ tty->driver->flush_buffer(tty);
+
+ /* Restore default settings */
+ dev->type = ARPHRD_AX25;
+
+ /* Perform the low-level AX25 initialization. */
+ if ((err = ax_open(ax->dev))) {
+ goto out_free_netdev;
+ }
+
+ if (register_netdev(dev))
+ goto out_free_buffers;
+
+ netif_start_queue(dev);
+
+ /* Done. We have linked the TTY line to a channel. */
+ return 0;
+
+out_free_buffers:
+ kfree(ax->rbuff);
+ kfree(ax->xbuff);
+
+out_free_netdev:
+ free_netdev(dev);
+
+out:
+ return err;
+}
+
+static void mkiss_close(struct tty_struct *tty)
+{
+ struct mkiss *ax;
+
+ write_lock(&disc_data_lock);
+ ax = tty->disc_data;
+ tty->disc_data = NULL;
+ write_unlock(&disc_data_lock);
+
+ if (ax == 0)
+ return;
+
+ /*
+ * We have now ensured that nobody can start using ap from now on, but
+ * we have to wait for all existing users to finish.
+ */
+ if (!atomic_dec_and_test(&ax->refcnt))
+ down(&ax->dead_sem);
+
+ unregister_netdev(ax->dev);
+
+ /* Free all AX25 frame buffers. */
+ kfree(ax->rbuff);
+ kfree(ax->xbuff);
+
+ ax->tty = NULL;
+}
+
+/* Perform I/O control on an active ax25 channel. */
+static int mkiss_ioctl(struct tty_struct *tty, struct file *file,
+ unsigned int cmd, unsigned long arg)
+{
+ struct mkiss *ax = mkiss_get(tty);
+ struct net_device *dev = ax->dev;
+ unsigned int tmp, err;
+
+ /* First make sure we're connected. */
+ if (ax == NULL)
+ return -ENXIO;
+
+ switch (cmd) {
+ case SIOCGIFNAME:
+ err = copy_to_user((void __user *) arg, ax->dev->name,
+ strlen(ax->dev->name) + 1) ? -EFAULT : 0;
+ break;
+
+ case SIOCGIFENCAP:
+ err = put_user(4, (int __user *) arg);
+ break;
+
+ case SIOCSIFENCAP:
+ if (get_user(tmp, (int __user *) arg)) {
+ err = -EFAULT;
+ break;
+ }
+
+ ax->mode = tmp;
+ dev->addr_len = AX25_ADDR_LEN;
+ dev->hard_header_len = AX25_KISS_HEADER_LEN +
+ AX25_MAX_HEADER_LEN + 3;
+ dev->type = ARPHRD_AX25;
+
+ err = 0;
+ break;
+
+ case SIOCSIFHWADDR: {
+ char addr[AX25_ADDR_LEN];
+printk(KERN_INFO "In SIOCSIFHWADDR");
+
+ if (copy_from_user(&addr,
+ (void __user *) arg, AX25_ADDR_LEN)) {
+ err = -EFAULT;
+ break;
+ }
+
+ spin_lock_irq(&dev->xmit_lock);
+ memcpy(dev->dev_addr, addr, AX25_ADDR_LEN);
+ spin_unlock_irq(&dev->xmit_lock);
+
+ err = 0;
+ break;
+ }
+ default:
+ err = -ENOIOCTLCMD;
+ }
+
+ mkiss_put(ax);
+
+ return err;
}
/*
@@ -555,11 +795,12 @@
* a block of data has been received, which can now be decapsulated
* and sent on to the AX.25 layer for further processing.
*/
-static void ax25_receive_buf(struct tty_struct *tty, const unsigned char *cp, char *fp, int count)
+static void mkiss_receive_buf(struct tty_struct *tty, const unsigned char *cp,
+ char *fp, int count)
{
- struct ax_disp *ax = (struct ax_disp *) tty->disc_data;
+ struct mkiss *ax = mkiss_get(tty);
- if (ax == NULL || ax->magic != AX25_MAGIC || !netif_running(ax->dev))
+ if (!ax)
return;
/*
@@ -573,312 +814,70 @@
while (count--) {
if (fp != NULL && *fp++) {
if (!test_and_set_bit(AXF_ERROR, &ax->flags))
- ax->rx_errors++;
+ ax->stats.rx_errors++;
cp++;
continue;
}
kiss_unesc(ax, *cp++);
}
+
+ mkiss_put(ax);
+ if (test_and_clear_bit(TTY_THROTTLED, &tty->flags)
+ && tty->driver->unthrottle)
+ tty->driver->unthrottle(tty);
}
-static int ax25_open(struct tty_struct *tty)
+static int mkiss_receive_room(struct tty_struct *tty)
{
- struct ax_disp *ax = (struct ax_disp *) tty->disc_data;
- int err;
-
- /* First make sure we're not already connected. */
- if (ax && ax->magic == AX25_MAGIC)
- return -EEXIST;
-
- /* OK. Find a free AX25 channel to use. */
- if ((ax = ax_alloc()) == NULL)
- return -ENFILE;
-
- ax->tty = tty;
- tty->disc_data = ax;
-
- if (tty->driver->flush_buffer)
- tty->driver->flush_buffer(tty);
-
- /* Restore default settings */
- ax->dev->type = ARPHRD_AX25;
-
- /* Perform the low-level AX25 initialization. */
- if ((err = ax_open(ax->dev)))
- return err;
-
- /* Done. We have linked the TTY line to a channel. */
- return ax->dev->base_addr;
-}
-
-static void ax25_close(struct tty_struct *tty)
-{
- struct ax_disp *ax = (struct ax_disp *) tty->disc_data;
-
- /* First make sure we're connected. */
- if (ax == NULL || ax->magic != AX25_MAGIC)
- return;
-
- unregister_netdev(ax->dev);
-
- tty->disc_data = NULL;
- ax->tty = NULL;
-
- ax_free(ax);
-}
-
-
-static struct net_device_stats *ax_get_stats(struct net_device *dev)
-{
- static struct net_device_stats stats;
- struct ax_disp *ax = netdev_priv(dev);
-
- memset(&stats, 0, sizeof(struct net_device_stats));
-
- stats.rx_packets = ax->rx_packets;
- stats.tx_packets = ax->tx_packets;
- stats.rx_bytes = ax->rx_bytes;
- stats.tx_bytes = ax->tx_bytes;
- stats.rx_dropped = ax->rx_dropped;
- stats.tx_dropped = ax->tx_dropped;
- stats.tx_errors = ax->tx_errors;
- stats.rx_errors = ax->rx_errors;
- stats.rx_over_errors = ax->rx_over_errors;
-
- return &stats;
-}
-
-
-/************************************************************************
- * STANDARD ENCAPSULATION *
- ************************************************************************/
-
-static int kiss_esc(unsigned char *s, unsigned char *d, int len)
-{
- unsigned char *ptr = d;
- unsigned char c;
-
- /*
- * Send an initial END character to flush out any
- * data that may have accumulated in the receiver
- * due to line noise.
- */
-
- *ptr++ = END;
-
- while (len-- > 0) {
- switch (c = *s++) {
- case END:
- *ptr++ = ESC;
- *ptr++ = ESC_END;
- break;
- case ESC:
- *ptr++ = ESC;
- *ptr++ = ESC_ESC;
- break;
- default:
- *ptr++ = c;
- break;
- }
- }
-
- *ptr++ = END;
-
- return ptr - d;
+ return 65536; /* We can handle an infinite amount of data. :-) */
}
/*
- * MW:
- * OK its ugly, but tell me a better solution without copying the
- * packet to a temporary buffer :-)
+ * Called by the driver when there's room for more data. If we have
+ * more packets to send, we send them here.
*/
-static int kiss_esc_crc(unsigned char *s, unsigned char *d, unsigned short crc, int len)
+static void mkiss_write_wakeup(struct tty_struct *tty)
{
- unsigned char *ptr = d;
- unsigned char c=0;
+ struct mkiss *ax = mkiss_get(tty);
+ int actual;
- *ptr++ = END;
- while (len > 0) {
- if (len > 2)
- c = *s++;
- else if (len > 1)
- c = crc >> 8;
- else if (len > 0)
- c = crc & 0xff;
+ if (!ax)
+ return;
- len--;
+ if (ax->xleft <= 0) {
+ /* Now serial buffer is almost free & we can start
+ * transmission of another packet
+ */
+ clear_bit(TTY_DO_WRITE_WAKEUP, &tty->flags);
- switch (c) {
- case END:
- *ptr++ = ESC;
- *ptr++ = ESC_END;
- break;
- case ESC:
- *ptr++ = ESC;
- *ptr++ = ESC_ESC;
- break;
- default:
- *ptr++ = c;
- break;
- }
- }
- *ptr++ = END;
- return ptr - d;
-}
-
-static void kiss_unesc(struct ax_disp *ax, unsigned char s)
-{
- switch (s) {
- case END:
- /* drop keeptest bit = VSV */
- if (test_bit(AXF_KEEPTEST, &ax->flags))
- clear_bit(AXF_KEEPTEST, &ax->flags);
-
- if (!test_and_clear_bit(AXF_ERROR, &ax->flags) && (ax->rcount > 2))
- ax_bump(ax);
-
- clear_bit(AXF_ESCAPE, &ax->flags);
- ax->rcount = 0;
- return;
-
- case ESC:
- set_bit(AXF_ESCAPE, &ax->flags);
- return;
- case ESC_ESC:
- if (test_and_clear_bit(AXF_ESCAPE, &ax->flags))
- s = ESC;
- break;
- case ESC_END:
- if (test_and_clear_bit(AXF_ESCAPE, &ax->flags))
- s = END;
- break;
+ netif_wake_queue(ax->dev);
+ goto out;
}
- spin_lock_bh(&ax->buflock);
- if (!test_bit(AXF_ERROR, &ax->flags)) {
- if (ax->rcount < ax->buffsize) {
- ax->rbuff[ax->rcount++] = s;
- spin_unlock_bh(&ax->buflock);
- return;
- }
+ actual = tty->driver->write(tty, ax->xhead, ax->xleft);
+ ax->xleft -= actual;
+ ax->xhead += actual;
- ax->rx_over_errors++;
- set_bit(AXF_ERROR, &ax->flags);
- }
- spin_unlock_bh(&ax->buflock);
+out:
+ mkiss_put(ax);
}
+static struct tty_ldisc ax_ldisc = {
+ .magic = TTY_LDISC_MAGIC,
+ .name = "mkiss",
+ .open = mkiss_open,
+ .close = mkiss_close,
+ .ioctl = mkiss_ioctl,
+ .receive_buf = mkiss_receive_buf,
+ .receive_room = mkiss_receive_room,
+ .write_wakeup = mkiss_write_wakeup
+};
-static int ax_set_mac_address(struct net_device *dev, void __user *addr)
-{
- if (copy_from_user(dev->dev_addr, addr, AX25_ADDR_LEN))
- return -EFAULT;
- return 0;
-}
-
-static int ax_set_dev_mac_address(struct net_device *dev, void *addr)
-{
- struct sockaddr *sa = addr;
-
- memcpy(dev->dev_addr, sa->sa_data, AX25_ADDR_LEN);
-
- return 0;
-}
-
-
-/* Perform I/O control on an active ax25 channel. */
-static int ax25_disp_ioctl(struct tty_struct *tty, void *file, int cmd, void __user *arg)
-{
- struct ax_disp *ax = (struct ax_disp *) tty->disc_data;
- unsigned int tmp;
-
- /* First make sure we're connected. */
- if (ax == NULL || ax->magic != AX25_MAGIC)
- return -EINVAL;
-
- switch (cmd) {
- case SIOCGIFNAME:
- if (copy_to_user(arg, ax->dev->name, strlen(ax->dev->name) + 1))
- return -EFAULT;
- return 0;
-
- case SIOCGIFENCAP:
- return put_user(4, (int __user *)arg);
-
- case SIOCSIFENCAP:
- if (get_user(tmp, (int __user *)arg))
- return -EFAULT;
- ax->mode = tmp;
- ax->dev->addr_len = AX25_ADDR_LEN; /* sizeof an AX.25 addr */
- ax->dev->hard_header_len = AX25_KISS_HEADER_LEN + AX25_MAX_HEADER_LEN + 3;
- ax->dev->type = ARPHRD_AX25;
- return 0;
-
- case SIOCSIFHWADDR:
- return ax_set_mac_address(ax->dev, arg);
-
- default:
- return -ENOIOCTLCMD;
- }
-}
-
-static int ax_open_dev(struct net_device *dev)
-{
- struct ax_disp *ax = netdev_priv(dev);
-
- if (ax->tty == NULL)
- return -ENODEV;
-
- return 0;
-}
-
-
-/* Initialize the driver. Called by network startup. */
-static int ax25_init(struct net_device *dev)
-{
- struct ax_disp *ax = netdev_priv(dev);
-
- static char ax25_bcast[AX25_ADDR_LEN] =
- {'Q'<<1,'S'<<1,'T'<<1,' '<<1,' '<<1,' '<<1,'0'<<1};
- static char ax25_test[AX25_ADDR_LEN] =
- {'L'<<1,'I'<<1,'N'<<1,'U'<<1,'X'<<1,' '<<1,'1'<<1};
-
- if (ax == NULL) /* Allocation failed ?? */
- return -ENODEV;
-
- /* Set up the "AX25 Control Block". (And clear statistics) */
- memset(ax, 0, sizeof (struct ax_disp));
- ax->magic = AX25_MAGIC;
- ax->dev = dev;
-
- /* Finish setting up the DEVICE info. */
- dev->mtu = AX_MTU;
- dev->hard_start_xmit = ax_xmit;
- dev->open = ax_open_dev;
- dev->stop = ax_close;
- dev->get_stats = ax_get_stats;
- dev->set_mac_address = ax_set_dev_mac_address;
- dev->hard_header_len = 0;
- dev->addr_len = 0;
- dev->type = ARPHRD_AX25;
- dev->tx_queue_len = 10;
- dev->hard_header = ax_header;
- dev->rebuild_header = ax_rebuild_header;
-
- memcpy(dev->broadcast, ax25_bcast, AX25_ADDR_LEN);
- memcpy(dev->dev_addr, ax25_test, AX25_ADDR_LEN);
-
- /* New-style flags. */
- dev->flags = IFF_BROADCAST | IFF_MULTICAST;
-
- return 0;
-}
-
-
-/* ******************************************************************** */
-/* * Init MKISS driver * */
-/* ******************************************************************** */
+static char banner[] __initdata = KERN_INFO \
+ "mkiss: AX.25 Multikiss, Hans Albas PE1AYX\n";
+static char msg_regfail[] __initdata = KERN_ERR \
+ "mkiss: can't register line discipline (err = %d)\n";
static int __init mkiss_init_driver(void)
{
@@ -886,64 +885,27 @@
printk(banner);
- if (ax25_maxdev < 4)
- ax25_maxdev = 4; /* Sanity */
+ if ((status = tty_register_ldisc(N_AX25, &ax_ldisc)) != 0)
+ printk(msg_regfail);
- if ((ax25_ctrls = kmalloc(sizeof(void *) * ax25_maxdev, GFP_KERNEL)) == NULL) {
- printk(KERN_ERR "mkiss: Can't allocate ax25_ctrls[] array!\n");
- return -ENOMEM;
- }
-
- /* Clear the pointer array, we allocate devices when we need them */
- memset(ax25_ctrls, 0, sizeof(void*) * ax25_maxdev); /* Pointers */
-
- /* Fill in our line protocol discipline, and register it */
- ax_ldisc.magic = TTY_LDISC_MAGIC;
- ax_ldisc.name = "mkiss";
- ax_ldisc.open = ax25_open;
- ax_ldisc.close = ax25_close;
- ax_ldisc.ioctl = (int (*)(struct tty_struct *, struct file *,
- unsigned int, unsigned long))ax25_disp_ioctl;
- ax_ldisc.receive_buf = ax25_receive_buf;
- ax_ldisc.receive_room = ax25_receive_room;
- ax_ldisc.write_wakeup = ax25_write_wakeup;
-
- if ((status = tty_register_ldisc(N_AX25, &ax_ldisc)) != 0) {
- printk(KERN_ERR "mkiss: can't register line discipline (err = %d)\n", status);
- kfree(ax25_ctrls);
- }
return status;
}
+static const char msg_unregfail[] __exitdata = KERN_ERR \
+ "mkiss: can't unregister line discipline (err = %d)\n";
+
static void __exit mkiss_exit_driver(void)
{
- int i;
+ int ret;
- for (i = 0; i < ax25_maxdev; i++) {
- if (ax25_ctrls[i]) {
- /*
- * VSV = if dev->start==0, then device
- * unregistered while close proc.
- */
- if (netif_running(&ax25_ctrls[i]->dev))
- unregister_netdev(&ax25_ctrls[i]->dev);
- kfree(ax25_ctrls[i]);
- }
- }
-
- kfree(ax25_ctrls);
- ax25_ctrls = NULL;
-
- if ((i = tty_unregister_ldisc(N_AX25)))
- printk(KERN_ERR "mkiss: can't unregister line discipline (err = %d)\n", i);
+ if ((ret = tty_unregister_ldisc(N_AX25)))
+ printk(msg_unregfail, ret);
}
-MODULE_AUTHOR("Hans Albas PE1AYX <hans@esrac.ele.tue.nl>");
+MODULE_AUTHOR("Ralf Baechle DL5RB <ralf@linux-mips.org>");
MODULE_DESCRIPTION("KISS driver for AX.25 over TTYs");
-MODULE_PARM(ax25_maxdev, "i");
-MODULE_PARM_DESC(ax25_maxdev, "number of MKISS devices");
MODULE_LICENSE("GPL");
MODULE_ALIAS_LDISC(N_AX25);
+
module_init(mkiss_init_driver);
module_exit(mkiss_exit_driver);
-
diff --git a/drivers/net/ixgb/ixgb.h b/drivers/net/ixgb/ixgb.h
index f8d3385..c83271b 100644
--- a/drivers/net/ixgb/ixgb.h
+++ b/drivers/net/ixgb/ixgb.h
@@ -119,7 +119,7 @@
* so a DMA handle can be stored along with the buffer */
struct ixgb_buffer {
struct sk_buff *skb;
- uint64_t dma;
+ dma_addr_t dma;
unsigned long time_stamp;
uint16_t length;
uint16_t next_to_watch;
diff --git a/drivers/net/ixgb/ixgb_ee.c b/drivers/net/ixgb/ixgb_ee.c
index 3aae110..661a46b 100644
--- a/drivers/net/ixgb/ixgb_ee.c
+++ b/drivers/net/ixgb/ixgb_ee.c
@@ -565,24 +565,6 @@
}
}
-/******************************************************************************
- * return the compatibility flags from EEPROM
- *
- * hw - Struct containing variables accessed by shared code
- *
- * Returns:
- * compatibility flags if EEPROM contents are valid, 0 otherwise
- ******************************************************************************/
-uint16_t
-ixgb_get_ee_compatibility(struct ixgb_hw *hw)
-{
- struct ixgb_ee_map_type *ee_map = (struct ixgb_ee_map_type *)hw->eeprom;
-
- if(ixgb_check_and_get_eeprom_data(hw) == TRUE)
- return (le16_to_cpu(ee_map->compatibility));
-
- return(0);
-}
/******************************************************************************
* return the Printed Board Assembly number from EEPROM
@@ -602,81 +584,6 @@
return(0);
}
-/******************************************************************************
- * return the Initialization Control Word 1 from EEPROM
- *
- * hw - Struct containing variables accessed by shared code
- *
- * Returns:
- * Initialization Control Word 1 if EEPROM contents are valid, 0 otherwise
- ******************************************************************************/
-uint16_t
-ixgb_get_ee_init_ctrl_reg_1(struct ixgb_hw *hw)
-{
- struct ixgb_ee_map_type *ee_map = (struct ixgb_ee_map_type *)hw->eeprom;
-
- if(ixgb_check_and_get_eeprom_data(hw) == TRUE)
- return (le16_to_cpu(ee_map->init_ctrl_reg_1));
-
- return(0);
-}
-
-/******************************************************************************
- * return the Initialization Control Word 2 from EEPROM
- *
- * hw - Struct containing variables accessed by shared code
- *
- * Returns:
- * Initialization Control Word 2 if EEPROM contents are valid, 0 otherwise
- ******************************************************************************/
-uint16_t
-ixgb_get_ee_init_ctrl_reg_2(struct ixgb_hw *hw)
-{
- struct ixgb_ee_map_type *ee_map = (struct ixgb_ee_map_type *)hw->eeprom;
-
- if(ixgb_check_and_get_eeprom_data(hw) == TRUE)
- return (le16_to_cpu(ee_map->init_ctrl_reg_2));
-
- return(0);
-}
-
-/******************************************************************************
- * return the Subsystem Id from EEPROM
- *
- * hw - Struct containing variables accessed by shared code
- *
- * Returns:
- * Subsystem Id if EEPROM contents are valid, 0 otherwise
- ******************************************************************************/
-uint16_t
-ixgb_get_ee_subsystem_id(struct ixgb_hw *hw)
-{
- struct ixgb_ee_map_type *ee_map = (struct ixgb_ee_map_type *)hw->eeprom;
-
- if(ixgb_check_and_get_eeprom_data(hw) == TRUE)
- return (le16_to_cpu(ee_map->subsystem_id));
-
- return(0);
-}
-
-/******************************************************************************
- * return the Sub Vendor Id from EEPROM
- *
- * hw - Struct containing variables accessed by shared code
- *
- * Returns:
- * Sub Vendor Id if EEPROM contents are valid, 0 otherwise
- ******************************************************************************/
-uint16_t
-ixgb_get_ee_subvendor_id(struct ixgb_hw *hw)
-{
- struct ixgb_ee_map_type *ee_map = (struct ixgb_ee_map_type *)hw->eeprom;
-
- if(ixgb_check_and_get_eeprom_data(hw) == TRUE)
- return (le16_to_cpu(ee_map->subvendor_id));
-
- return(0);
-}
/******************************************************************************
* return the Device Id from EEPROM
@@ -694,81 +601,6 @@
if(ixgb_check_and_get_eeprom_data(hw) == TRUE)
return (le16_to_cpu(ee_map->device_id));
- return(0);
+ return (0);
}
-/******************************************************************************
- * return the Vendor Id from EEPROM
- *
- * hw - Struct containing variables accessed by shared code
- *
- * Returns:
- * Device Id if EEPROM contents are valid, 0 otherwise
- ******************************************************************************/
-uint16_t
-ixgb_get_ee_vendor_id(struct ixgb_hw *hw)
-{
- struct ixgb_ee_map_type *ee_map = (struct ixgb_ee_map_type *)hw->eeprom;
-
- if(ixgb_check_and_get_eeprom_data(hw) == TRUE)
- return (le16_to_cpu(ee_map->vendor_id));
-
- return(0);
-}
-
-/******************************************************************************
- * return the Software Defined Pins Register from EEPROM
- *
- * hw - Struct containing variables accessed by shared code
- *
- * Returns:
- * SDP Register if EEPROM contents are valid, 0 otherwise
- ******************************************************************************/
-uint16_t
-ixgb_get_ee_swdpins_reg(struct ixgb_hw *hw)
-{
- struct ixgb_ee_map_type *ee_map = (struct ixgb_ee_map_type *)hw->eeprom;
-
- if(ixgb_check_and_get_eeprom_data(hw) == TRUE)
- return (le16_to_cpu(ee_map->swdpins_reg));
-
- return(0);
-}
-
-/******************************************************************************
- * return the D3 Power Management Bits from EEPROM
- *
- * hw - Struct containing variables accessed by shared code
- *
- * Returns:
- * D3 Power Management Bits if EEPROM contents are valid, 0 otherwise
- ******************************************************************************/
-uint8_t
-ixgb_get_ee_d3_power(struct ixgb_hw *hw)
-{
- struct ixgb_ee_map_type *ee_map = (struct ixgb_ee_map_type *)hw->eeprom;
-
- if(ixgb_check_and_get_eeprom_data(hw) == TRUE)
- return (le16_to_cpu(ee_map->d3_power));
-
- return(0);
-}
-
-/******************************************************************************
- * return the D0 Power Management Bits from EEPROM
- *
- * hw - Struct containing variables accessed by shared code
- *
- * Returns:
- * D0 Power Management Bits if EEPROM contents are valid, 0 otherwise
- ******************************************************************************/
-uint8_t
-ixgb_get_ee_d0_power(struct ixgb_hw *hw)
-{
- struct ixgb_ee_map_type *ee_map = (struct ixgb_ee_map_type *)hw->eeprom;
-
- if(ixgb_check_and_get_eeprom_data(hw) == TRUE)
- return (le16_to_cpu(ee_map->d0_power));
-
- return(0);
-}
diff --git a/drivers/net/ixgb/ixgb_ethtool.c b/drivers/net/ixgb/ixgb_ethtool.c
index 3fa1138..9d026ed 100644
--- a/drivers/net/ixgb/ixgb_ethtool.c
+++ b/drivers/net/ixgb/ixgb_ethtool.c
@@ -98,10 +98,10 @@
static int
ixgb_get_settings(struct net_device *netdev, struct ethtool_cmd *ecmd)
{
- struct ixgb_adapter *adapter = netdev->priv;
+ struct ixgb_adapter *adapter = netdev_priv(netdev);
ecmd->supported = (SUPPORTED_10000baseT_Full | SUPPORTED_FIBRE);
- ecmd->advertising = (SUPPORTED_10000baseT_Full | SUPPORTED_FIBRE);
+ ecmd->advertising = (ADVERTISED_10000baseT_Full | ADVERTISED_FIBRE);
ecmd->port = PORT_FIBRE;
ecmd->transceiver = XCVR_EXTERNAL;
@@ -120,7 +120,7 @@
static int
ixgb_set_settings(struct net_device *netdev, struct ethtool_cmd *ecmd)
{
- struct ixgb_adapter *adapter = netdev->priv;
+ struct ixgb_adapter *adapter = netdev_priv(netdev);
if(ecmd->autoneg == AUTONEG_ENABLE ||
ecmd->speed + ecmd->duplex != SPEED_10000 + DUPLEX_FULL)
@@ -130,6 +130,12 @@
ixgb_down(adapter, TRUE);
ixgb_reset(adapter);
ixgb_up(adapter);
+ /* be optimistic about our link, since we were up before */
+ adapter->link_speed = 10000;
+ adapter->link_duplex = FULL_DUPLEX;
+ netif_carrier_on(netdev);
+ netif_wake_queue(netdev);
+
} else
ixgb_reset(adapter);
@@ -140,7 +146,7 @@
ixgb_get_pauseparam(struct net_device *netdev,
struct ethtool_pauseparam *pause)
{
- struct ixgb_adapter *adapter = netdev->priv;
+ struct ixgb_adapter *adapter = netdev_priv(netdev);
struct ixgb_hw *hw = &adapter->hw;
pause->autoneg = AUTONEG_DISABLE;
@@ -159,7 +165,7 @@
ixgb_set_pauseparam(struct net_device *netdev,
struct ethtool_pauseparam *pause)
{
- struct ixgb_adapter *adapter = netdev->priv;
+ struct ixgb_adapter *adapter = netdev_priv(netdev);
struct ixgb_hw *hw = &adapter->hw;
if(pause->autoneg == AUTONEG_ENABLE)
@@ -177,6 +183,11 @@
if(netif_running(adapter->netdev)) {
ixgb_down(adapter, TRUE);
ixgb_up(adapter);
+ /* be optimistic about our link, since we were up before */
+ adapter->link_speed = 10000;
+ adapter->link_duplex = FULL_DUPLEX;
+ netif_carrier_on(netdev);
+ netif_wake_queue(netdev);
} else
ixgb_reset(adapter);
@@ -186,19 +197,26 @@
static uint32_t
ixgb_get_rx_csum(struct net_device *netdev)
{
- struct ixgb_adapter *adapter = netdev->priv;
+ struct ixgb_adapter *adapter = netdev_priv(netdev);
+
return adapter->rx_csum;
}
static int
ixgb_set_rx_csum(struct net_device *netdev, uint32_t data)
{
- struct ixgb_adapter *adapter = netdev->priv;
+ struct ixgb_adapter *adapter = netdev_priv(netdev);
+
adapter->rx_csum = data;
if(netif_running(netdev)) {
ixgb_down(adapter,TRUE);
ixgb_up(adapter);
+ /* be optimistic about our link, since we were up before */
+ adapter->link_speed = 10000;
+ adapter->link_duplex = FULL_DUPLEX;
+ netif_carrier_on(netdev);
+ netif_wake_queue(netdev);
} else
ixgb_reset(adapter);
return 0;
@@ -246,14 +264,15 @@
ixgb_get_regs(struct net_device *netdev,
struct ethtool_regs *regs, void *p)
{
- struct ixgb_adapter *adapter = netdev->priv;
+ struct ixgb_adapter *adapter = netdev_priv(netdev);
struct ixgb_hw *hw = &adapter->hw;
uint32_t *reg = p;
uint32_t *reg_start = reg;
uint8_t i;
/* the 1 (one) below indicates an attempt at versioning, if the
- * interface in ethtool or the driver this 1 should be incremented */
+ * interface in ethtool or the driver changes, this 1 should be
+ * incremented */
regs->version = (1<<24) | hw->revision_id << 16 | hw->device_id;
/* General Registers */
@@ -283,7 +302,8 @@
*reg++ = IXGB_READ_REG(hw, RAIDC); /* 19 */
*reg++ = IXGB_READ_REG(hw, RXCSUM); /* 20 */
- for (i = 0; i < IXGB_RAR_ENTRIES; i++) {
+ /* there are 16 RAR entries in hardware, we only use 3 */
+ for(i = 0; i < 16; i++) {
*reg++ = IXGB_READ_REG_ARRAY(hw, RAL, (i << 1)); /*21,...,51 */
*reg++ = IXGB_READ_REG_ARRAY(hw, RAH, (i << 1)); /*22,...,52 */
}
@@ -391,7 +411,7 @@
ixgb_get_eeprom(struct net_device *netdev,
struct ethtool_eeprom *eeprom, uint8_t *bytes)
{
- struct ixgb_adapter *adapter = netdev->priv;
+ struct ixgb_adapter *adapter = netdev_priv(netdev);
struct ixgb_hw *hw = &adapter->hw;
uint16_t *eeprom_buff;
int i, max_len, first_word, last_word;
@@ -439,7 +459,7 @@
ixgb_set_eeprom(struct net_device *netdev,
struct ethtool_eeprom *eeprom, uint8_t *bytes)
{
- struct ixgb_adapter *adapter = netdev->priv;
+ struct ixgb_adapter *adapter = netdev_priv(netdev);
struct ixgb_hw *hw = &adapter->hw;
uint16_t *eeprom_buff;
void *ptr;
@@ -497,7 +517,7 @@
ixgb_get_drvinfo(struct net_device *netdev,
struct ethtool_drvinfo *drvinfo)
{
- struct ixgb_adapter *adapter = netdev->priv;
+ struct ixgb_adapter *adapter = netdev_priv(netdev);
strncpy(drvinfo->driver, ixgb_driver_name, 32);
strncpy(drvinfo->version, ixgb_driver_version, 32);
@@ -512,7 +532,7 @@
ixgb_get_ringparam(struct net_device *netdev,
struct ethtool_ringparam *ring)
{
- struct ixgb_adapter *adapter = netdev->priv;
+ struct ixgb_adapter *adapter = netdev_priv(netdev);
struct ixgb_desc_ring *txdr = &adapter->tx_ring;
struct ixgb_desc_ring *rxdr = &adapter->rx_ring;
@@ -530,7 +550,7 @@
ixgb_set_ringparam(struct net_device *netdev,
struct ethtool_ringparam *ring)
{
- struct ixgb_adapter *adapter = netdev->priv;
+ struct ixgb_adapter *adapter = netdev_priv(netdev);
struct ixgb_desc_ring *txdr = &adapter->tx_ring;
struct ixgb_desc_ring *rxdr = &adapter->rx_ring;
struct ixgb_desc_ring tx_old, tx_new, rx_old, rx_new;
@@ -573,6 +593,11 @@
adapter->tx_ring = tx_new;
if((err = ixgb_up(adapter)))
return err;
+ /* be optimistic about our link, since we were up before */
+ adapter->link_speed = 10000;
+ adapter->link_duplex = FULL_DUPLEX;
+ netif_carrier_on(netdev);
+ netif_wake_queue(netdev);
}
return 0;
@@ -607,7 +632,7 @@
static int
ixgb_phys_id(struct net_device *netdev, uint32_t data)
{
- struct ixgb_adapter *adapter = netdev->priv;
+ struct ixgb_adapter *adapter = netdev_priv(netdev);
if(!data || data > (uint32_t)(MAX_SCHEDULE_TIMEOUT / HZ))
data = (uint32_t)(MAX_SCHEDULE_TIMEOUT / HZ);
@@ -643,7 +668,7 @@
ixgb_get_ethtool_stats(struct net_device *netdev,
struct ethtool_stats *stats, uint64_t *data)
{
- struct ixgb_adapter *adapter = netdev->priv;
+ struct ixgb_adapter *adapter = netdev_priv(netdev);
int i;
ixgb_update_stats(adapter);
diff --git a/drivers/net/ixgb/ixgb_hw.h b/drivers/net/ixgb/ixgb_hw.h
index 97898ef..8bcf31e 100644
--- a/drivers/net/ixgb/ixgb_hw.h
+++ b/drivers/net/ixgb/ixgb_hw.h
@@ -822,17 +822,8 @@
/* Access functions to eeprom data */
void ixgb_get_ee_mac_addr(struct ixgb_hw *hw, uint8_t *mac_addr);
-uint16_t ixgb_get_ee_compatibility(struct ixgb_hw *hw);
uint32_t ixgb_get_ee_pba_number(struct ixgb_hw *hw);
-uint16_t ixgb_get_ee_init_ctrl_reg_1(struct ixgb_hw *hw);
-uint16_t ixgb_get_ee_init_ctrl_reg_2(struct ixgb_hw *hw);
-uint16_t ixgb_get_ee_subsystem_id(struct ixgb_hw *hw);
-uint16_t ixgb_get_ee_subvendor_id(struct ixgb_hw *hw);
uint16_t ixgb_get_ee_device_id(struct ixgb_hw *hw);
-uint16_t ixgb_get_ee_vendor_id(struct ixgb_hw *hw);
-uint16_t ixgb_get_ee_swdpins_reg(struct ixgb_hw *hw);
-uint8_t ixgb_get_ee_d3_power(struct ixgb_hw *hw);
-uint8_t ixgb_get_ee_d0_power(struct ixgb_hw *hw);
boolean_t ixgb_get_eeprom_data(struct ixgb_hw *hw);
uint16_t ixgb_get_eeprom_word(struct ixgb_hw *hw, uint16_t index);
diff --git a/drivers/net/ixgb/ixgb_main.c b/drivers/net/ixgb/ixgb_main.c
index 097b90c..5c55537 100644
--- a/drivers/net/ixgb/ixgb_main.c
+++ b/drivers/net/ixgb/ixgb_main.c
@@ -29,6 +29,11 @@
#include "ixgb.h"
/* Change Log
+ * 1.0.96 04/19/05
+ * - Make needlessly global code static -- bunk@stusta.de
+ * - ethtool cleanup -- shemminger@osdl.org
+ * - Support for MODULE_VERSION -- linville@tuxdriver.com
+ * - add skb_header_cloned check to the tso path -- herbert@apana.org.au
* 1.0.88 01/05/05
* - include fix to the condition that determines when to quit NAPI - Robert Olsson
* - use netif_poll_{disable/enable} to synchronize between NAPI and i/f up/down
@@ -47,10 +52,9 @@
#else
#define DRIVERNAPI "-NAPI"
#endif
-
-#define DRV_VERSION "1.0.95-k2"DRIVERNAPI
+#define DRV_VERSION "1.0.100-k2"DRIVERNAPI
char ixgb_driver_version[] = DRV_VERSION;
-char ixgb_copyright[] = "Copyright (c) 1999-2005 Intel Corporation.";
+static char ixgb_copyright[] = "Copyright (c) 1999-2005 Intel Corporation.";
/* ixgb_pci_tbl - PCI Device ID Table
*
@@ -145,10 +149,12 @@
MODULE_VERSION(DRV_VERSION);
/* some defines for controlling descriptor fetches in h/w */
-#define RXDCTL_PTHRESH_DEFAULT 128 /* chip considers prefech below this */
-#define RXDCTL_HTHRESH_DEFAULT 16 /* chip will only prefetch if tail is
- pushed this many descriptors from head */
#define RXDCTL_WTHRESH_DEFAULT 16 /* chip writes back at this many or RXT0 */
+#define RXDCTL_PTHRESH_DEFAULT 0 /* chip considers prefech below
+ * this */
+#define RXDCTL_HTHRESH_DEFAULT 0 /* chip will only prefetch if tail
+ * is pushed this many descriptors
+ * from head */
/**
* ixgb_init_module - Driver Registration Routine
@@ -376,7 +382,7 @@
SET_NETDEV_DEV(netdev, &pdev->dev);
pci_set_drvdata(pdev, netdev);
- adapter = netdev->priv;
+ adapter = netdev_priv(netdev);
adapter->netdev = netdev;
adapter->pdev = pdev;
adapter->hw.back = adapter;
@@ -512,7 +518,7 @@
ixgb_remove(struct pci_dev *pdev)
{
struct net_device *netdev = pci_get_drvdata(pdev);
- struct ixgb_adapter *adapter = netdev->priv;
+ struct ixgb_adapter *adapter = netdev_priv(netdev);
unregister_netdev(netdev);
@@ -583,7 +589,7 @@
static int
ixgb_open(struct net_device *netdev)
{
- struct ixgb_adapter *adapter = netdev->priv;
+ struct ixgb_adapter *adapter = netdev_priv(netdev);
int err;
/* allocate transmit descriptors */
@@ -626,7 +632,7 @@
static int
ixgb_close(struct net_device *netdev)
{
- struct ixgb_adapter *adapter = netdev->priv;
+ struct ixgb_adapter *adapter = netdev_priv(netdev);
ixgb_down(adapter, TRUE);
@@ -1017,7 +1023,7 @@
static int
ixgb_set_mac(struct net_device *netdev, void *p)
{
- struct ixgb_adapter *adapter = netdev->priv;
+ struct ixgb_adapter *adapter = netdev_priv(netdev);
struct sockaddr *addr = p;
if(!is_valid_ether_addr(addr->sa_data))
@@ -1043,7 +1049,7 @@
static void
ixgb_set_multi(struct net_device *netdev)
{
- struct ixgb_adapter *adapter = netdev->priv;
+ struct ixgb_adapter *adapter = netdev_priv(netdev);
struct ixgb_hw *hw = &adapter->hw;
struct dev_mc_list *mc_ptr;
uint32_t rctl;
@@ -1371,7 +1377,7 @@
static int
ixgb_xmit_frame(struct sk_buff *skb, struct net_device *netdev)
{
- struct ixgb_adapter *adapter = netdev->priv;
+ struct ixgb_adapter *adapter = netdev_priv(netdev);
unsigned int first;
unsigned int tx_flags = 0;
unsigned long flags;
@@ -1425,7 +1431,7 @@
static void
ixgb_tx_timeout(struct net_device *netdev)
{
- struct ixgb_adapter *adapter = netdev->priv;
+ struct ixgb_adapter *adapter = netdev_priv(netdev);
/* Do the reset outside of interrupt context */
schedule_work(&adapter->tx_timeout_task);
@@ -1434,7 +1440,7 @@
static void
ixgb_tx_timeout_task(struct net_device *netdev)
{
- struct ixgb_adapter *adapter = netdev->priv;
+ struct ixgb_adapter *adapter = netdev_priv(netdev);
ixgb_down(adapter, TRUE);
ixgb_up(adapter);
@@ -1451,7 +1457,7 @@
static struct net_device_stats *
ixgb_get_stats(struct net_device *netdev)
{
- struct ixgb_adapter *adapter = netdev->priv;
+ struct ixgb_adapter *adapter = netdev_priv(netdev);
return &adapter->net_stats;
}
@@ -1467,7 +1473,7 @@
static int
ixgb_change_mtu(struct net_device *netdev, int new_mtu)
{
- struct ixgb_adapter *adapter = netdev->priv;
+ struct ixgb_adapter *adapter = netdev_priv(netdev);
int max_frame = new_mtu + ENET_HEADER_SIZE + ENET_FCS_LENGTH;
int old_max_frame = netdev->mtu + ENET_HEADER_SIZE + ENET_FCS_LENGTH;
@@ -1522,7 +1528,8 @@
multi |= ((u64)IXGB_READ_REG(&adapter->hw, MPRCH) << 32);
/* fix up multicast stats by removing broadcasts */
- multi -= bcast;
+ if(multi >= bcast)
+ multi -= bcast;
adapter->stats.mprcl += (multi & 0xFFFFFFFF);
adapter->stats.mprch += (multi >> 32);
@@ -1641,7 +1648,7 @@
ixgb_intr(int irq, void *data, struct pt_regs *regs)
{
struct net_device *netdev = data;
- struct ixgb_adapter *adapter = netdev->priv;
+ struct ixgb_adapter *adapter = netdev_priv(netdev);
struct ixgb_hw *hw = &adapter->hw;
uint32_t icr = IXGB_READ_REG(hw, ICR);
#ifndef CONFIG_IXGB_NAPI
@@ -1688,7 +1695,7 @@
static int
ixgb_clean(struct net_device *netdev, int *budget)
{
- struct ixgb_adapter *adapter = netdev->priv;
+ struct ixgb_adapter *adapter = netdev_priv(netdev);
int work_to_do = min(*budget, netdev->quota);
int tx_cleaned;
int work_done = 0;
@@ -2017,7 +2024,7 @@
static void
ixgb_vlan_rx_register(struct net_device *netdev, struct vlan_group *grp)
{
- struct ixgb_adapter *adapter = netdev->priv;
+ struct ixgb_adapter *adapter = netdev_priv(netdev);
uint32_t ctrl, rctl;
ixgb_irq_disable(adapter);
@@ -2055,7 +2062,7 @@
static void
ixgb_vlan_rx_add_vid(struct net_device *netdev, uint16_t vid)
{
- struct ixgb_adapter *adapter = netdev->priv;
+ struct ixgb_adapter *adapter = netdev_priv(netdev);
uint32_t vfta, index;
/* add VID to filter table */
@@ -2069,7 +2076,7 @@
static void
ixgb_vlan_rx_kill_vid(struct net_device *netdev, uint16_t vid)
{
- struct ixgb_adapter *adapter = netdev->priv;
+ struct ixgb_adapter *adapter = netdev_priv(netdev);
uint32_t vfta, index;
ixgb_irq_disable(adapter);
diff --git a/drivers/net/jazzsonic.c b/drivers/net/jazzsonic.c
index 7fec613..8423cb6 100644
--- a/drivers/net/jazzsonic.c
+++ b/drivers/net/jazzsonic.c
@@ -1,5 +1,10 @@
/*
- * sonic.c
+ * jazzsonic.c
+ *
+ * (C) 2005 Finn Thain
+ *
+ * Converted to DMA API, and (from the mac68k project) introduced
+ * dhd's support for 16-bit cards.
*
* (C) 1996,1998 by Thomas Bogendoerfer (tsbogend@alpha.franken.de)
*
@@ -28,8 +33,8 @@
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/skbuff.h>
-#include <linux/bitops.h>
#include <linux/device.h>
+#include <linux/dma-mapping.h>
#include <asm/bootinfo.h>
#include <asm/system.h>
@@ -44,22 +49,20 @@
#define SONIC_MEM_SIZE 0x100
-#define SREGS_PAD(n) u16 n;
-
#include "sonic.h"
/*
* Macros to access SONIC registers
*/
-#define SONIC_READ(reg) (*((volatile unsigned int *)base_addr+reg))
+#define SONIC_READ(reg) (*((volatile unsigned int *)dev->base_addr+reg))
#define SONIC_WRITE(reg,val) \
do { \
- *((volatile unsigned int *)base_addr+(reg)) = (val); \
+ *((volatile unsigned int *)dev->base_addr+(reg)) = (val); \
} while (0)
-/* use 0 for production, 1 for verification, >2 for debug */
+/* use 0 for production, 1 for verification, >1 for debug */
#ifdef SONIC_DEBUG
static unsigned int sonic_debug = SONIC_DEBUG;
#else
@@ -85,18 +88,18 @@
0xffff /* end of list */
};
-static int __init sonic_probe1(struct net_device *dev, unsigned long base_addr,
- unsigned int irq)
+static int __init sonic_probe1(struct net_device *dev)
{
static unsigned version_printed;
unsigned int silicon_revision;
unsigned int val;
- struct sonic_local *lp;
+ struct sonic_local *lp = netdev_priv(dev);
int err = -ENODEV;
int i;
- if (!request_mem_region(base_addr, SONIC_MEM_SIZE, jazz_sonic_string))
+ if (!request_mem_region(dev->base_addr, SONIC_MEM_SIZE, jazz_sonic_string))
return -EBUSY;
+
/*
* get the Silicon Revision ID. If this is one of the known
* one assume that we found a SONIC ethernet controller at
@@ -120,11 +123,7 @@
if (sonic_debug && version_printed++ == 0)
printk(version);
- printk("%s: Sonic ethernet found at 0x%08lx, ", dev->name, base_addr);
-
- /* Fill in the 'dev' fields. */
- dev->base_addr = base_addr;
- dev->irq = irq;
+ printk(KERN_INFO "%s: Sonic ethernet found at 0x%08lx, ", lp->device->bus_id, dev->base_addr);
/*
* Put the sonic into software reset, then
@@ -138,84 +137,44 @@
dev->dev_addr[i*2+1] = val >> 8;
}
- printk("HW Address ");
- for (i = 0; i < 6; i++) {
- printk("%2.2x", dev->dev_addr[i]);
- if (i<5)
- printk(":");
- }
-
- printk(" IRQ %d\n", irq);
-
err = -ENOMEM;
/* Initialize the device structure. */
- if (dev->priv == NULL) {
- /*
- * the memory be located in the same 64kb segment
- */
- lp = NULL;
- i = 0;
- do {
- lp = kmalloc(sizeof(*lp), GFP_KERNEL);
- if ((unsigned long) lp >> 16
- != ((unsigned long)lp + sizeof(*lp) ) >> 16) {
- /* FIXME, free the memory later */
- kfree(lp);
- lp = NULL;
- }
- } while (lp == NULL && i++ < 20);
- if (lp == NULL) {
- printk("%s: couldn't allocate memory for descriptors\n",
- dev->name);
- goto out;
- }
+ lp->dma_bitmode = SONIC_BITMODE32;
- memset(lp, 0, sizeof(struct sonic_local));
-
- /* get the virtual dma address */
- lp->cda_laddr = vdma_alloc(CPHYSADDR(lp),sizeof(*lp));
- if (lp->cda_laddr == ~0UL) {
- printk("%s: couldn't get DMA page entry for "
- "descriptors\n", dev->name);
- goto out1;
- }
-
- lp->tda_laddr = lp->cda_laddr + sizeof (lp->cda);
- lp->rra_laddr = lp->tda_laddr + sizeof (lp->tda);
- lp->rda_laddr = lp->rra_laddr + sizeof (lp->rra);
-
- /* allocate receive buffer area */
- /* FIXME, maybe we should use skbs */
- lp->rba = kmalloc(SONIC_NUM_RRS * SONIC_RBSIZE, GFP_KERNEL);
- if (!lp->rba) {
- printk("%s: couldn't allocate receive buffers\n",
- dev->name);
- goto out2;
- }
-
- /* get virtual dma address */
- lp->rba_laddr = vdma_alloc(CPHYSADDR(lp->rba),
- SONIC_NUM_RRS * SONIC_RBSIZE);
- if (lp->rba_laddr == ~0UL) {
- printk("%s: couldn't get DMA page entry for receive "
- "buffers\n",dev->name);
- goto out3;
- }
-
- /* now convert pointer to KSEG1 pointer */
- lp->rba = (char *)KSEG1ADDR(lp->rba);
- flush_cache_all();
- dev->priv = (struct sonic_local *)KSEG1ADDR(lp);
+ /* Allocate the entire chunk of memory for the descriptors.
+ Note that this cannot cross a 64K boundary. */
+ if ((lp->descriptors = dma_alloc_coherent(lp->device,
+ SIZEOF_SONIC_DESC * SONIC_BUS_SCALE(lp->dma_bitmode),
+ &lp->descriptors_laddr, GFP_KERNEL)) == NULL) {
+ printk(KERN_ERR "%s: couldn't alloc DMA memory for descriptors.\n", lp->device->bus_id);
+ goto out;
}
- lp = (struct sonic_local *)dev->priv;
+ /* Now set up the pointers to point to the appropriate places */
+ lp->cda = lp->descriptors;
+ lp->tda = lp->cda + (SIZEOF_SONIC_CDA
+ * SONIC_BUS_SCALE(lp->dma_bitmode));
+ lp->rda = lp->tda + (SIZEOF_SONIC_TD * SONIC_NUM_TDS
+ * SONIC_BUS_SCALE(lp->dma_bitmode));
+ lp->rra = lp->rda + (SIZEOF_SONIC_RD * SONIC_NUM_RDS
+ * SONIC_BUS_SCALE(lp->dma_bitmode));
+
+ lp->cda_laddr = lp->descriptors_laddr;
+ lp->tda_laddr = lp->cda_laddr + (SIZEOF_SONIC_CDA
+ * SONIC_BUS_SCALE(lp->dma_bitmode));
+ lp->rda_laddr = lp->tda_laddr + (SIZEOF_SONIC_TD * SONIC_NUM_TDS
+ * SONIC_BUS_SCALE(lp->dma_bitmode));
+ lp->rra_laddr = lp->rda_laddr + (SIZEOF_SONIC_RD * SONIC_NUM_RDS
+ * SONIC_BUS_SCALE(lp->dma_bitmode));
+
dev->open = sonic_open;
dev->stop = sonic_close;
dev->hard_start_xmit = sonic_send_packet;
- dev->get_stats = sonic_get_stats;
+ dev->get_stats = sonic_get_stats;
dev->set_multicast_list = &sonic_multicast_list;
+ dev->tx_timeout = sonic_tx_timeout;
dev->watchdog_timeo = TX_TIMEOUT;
/*
@@ -226,14 +185,8 @@
SONIC_WRITE(SONIC_MPT,0xffff);
return 0;
-out3:
- kfree(lp->rba);
-out2:
- vdma_free(lp->cda_laddr);
-out1:
- kfree(lp);
out:
- release_region(base_addr, SONIC_MEM_SIZE);
+ release_region(dev->base_addr, SONIC_MEM_SIZE);
return err;
}
@@ -245,7 +198,6 @@
{
struct net_device *dev;
struct sonic_local *lp;
- unsigned long base_addr;
int err = 0;
int i;
@@ -255,21 +207,26 @@
if (mips_machgroup != MACH_GROUP_JAZZ)
return -ENODEV;
- dev = alloc_etherdev(0);
+ dev = alloc_etherdev(sizeof(struct sonic_local));
if (!dev)
return -ENOMEM;
- netdev_boot_setup_check(dev);
- base_addr = dev->base_addr;
+ lp = netdev_priv(dev);
+ lp->device = device;
+ SET_NETDEV_DEV(dev, device);
+ SET_MODULE_OWNER(dev);
- if (base_addr >= KSEG0) { /* Check a single specified location. */
- err = sonic_probe1(dev, base_addr, dev->irq);
- } else if (base_addr != 0) { /* Don't probe at all. */
+ netdev_boot_setup_check(dev);
+
+ if (dev->base_addr >= KSEG0) { /* Check a single specified location. */
+ err = sonic_probe1(dev);
+ } else if (dev->base_addr != 0) { /* Don't probe at all. */
err = -ENXIO;
} else {
for (i = 0; sonic_portlist[i].port; i++) {
- int io = sonic_portlist[i].port;
- if (sonic_probe1(dev, io, sonic_portlist[i].irq) == 0)
+ dev->base_addr = sonic_portlist[i].port;
+ dev->irq = sonic_portlist[i].irq;
+ if (sonic_probe1(dev) == 0)
break;
}
if (!sonic_portlist[i].port)
@@ -281,14 +238,17 @@
if (err)
goto out1;
+ printk("%s: MAC ", dev->name);
+ for (i = 0; i < 6; i++) {
+ printk("%2.2x", dev->dev_addr[i]);
+ if (i < 5)
+ printk(":");
+ }
+ printk(" IRQ %d\n", dev->irq);
+
return 0;
out1:
- lp = dev->priv;
- vdma_free(lp->rba_laddr);
- kfree(lp->rba);
- vdma_free(lp->cda_laddr);
- kfree(lp);
release_region(dev->base_addr, SONIC_MEM_SIZE);
out:
free_netdev(dev);
@@ -296,21 +256,22 @@
return err;
}
-/*
- * SONIC uses a normal IRQ
- */
-#define sonic_request_irq request_irq
-#define sonic_free_irq free_irq
+MODULE_DESCRIPTION("Jazz SONIC ethernet driver");
+module_param(sonic_debug, int, 0);
+MODULE_PARM_DESC(sonic_debug, "jazzsonic debug level (1-4)");
-#define sonic_chiptomem(x) KSEG1ADDR(vdma_log2phys(x))
+#define SONIC_IRQ_FLAG SA_INTERRUPT
#include "sonic.c"
static int __devexit jazz_sonic_device_remove (struct device *device)
{
struct net_device *dev = device->driver_data;
+ struct sonic_local* lp = netdev_priv(dev);
unregister_netdev (dev);
+ dma_free_coherent(lp->device, SIZEOF_SONIC_DESC * SONIC_BUS_SCALE(lp->dma_bitmode),
+ lp->descriptors, lp->descriptors_laddr);
release_region (dev->base_addr, SONIC_MEM_SIZE);
free_netdev (dev);
@@ -323,7 +284,7 @@
.probe = jazz_sonic_probe,
.remove = __devexit_p(jazz_sonic_device_remove),
};
-
+
static void jazz_sonic_platform_release (struct device *device)
{
struct platform_device *pldev;
@@ -336,10 +297,11 @@
static int __init jazz_sonic_init_module(void)
{
struct platform_device *pldev;
+ int err;
- if (driver_register(&jazz_sonic_driver)) {
+ if ((err = driver_register(&jazz_sonic_driver))) {
printk(KERN_ERR "Driver registration failed\n");
- return -ENOMEM;
+ return err;
}
jazz_sonic_device = NULL;
diff --git a/drivers/net/loopback.c b/drivers/net/loopback.c
index 1f61f0c..690a1aa 100644
--- a/drivers/net/loopback.c
+++ b/drivers/net/loopback.c
@@ -68,6 +68,7 @@
* of largesending device modulo TCP checksum, which is ignored for loopback.
*/
+#ifdef LOOPBACK_TSO
static void emulate_large_send_offload(struct sk_buff *skb)
{
struct iphdr *iph = skb->nh.iph;
@@ -119,6 +120,7 @@
dev_kfree_skb(skb);
}
+#endif /* LOOPBACK_TSO */
/*
* The higher levels take care of making this non-reentrant (it's
@@ -130,12 +132,13 @@
skb_orphan(skb);
- skb->protocol=eth_type_trans(skb,dev);
- skb->dev=dev;
+ skb->protocol = eth_type_trans(skb,dev);
+ skb->dev = dev;
#ifndef LOOPBACK_MUST_CHECKSUM
skb->ip_summed = CHECKSUM_UNNECESSARY;
#endif
+#ifdef LOOPBACK_TSO
if (skb_shinfo(skb)->tso_size) {
BUG_ON(skb->protocol != htons(ETH_P_IP));
BUG_ON(skb->nh.iph->protocol != IPPROTO_TCP);
@@ -143,14 +146,14 @@
emulate_large_send_offload(skb);
return 0;
}
-
+#endif
dev->last_rx = jiffies;
lb_stats = &per_cpu(loopback_stats, get_cpu());
lb_stats->rx_bytes += skb->len;
- lb_stats->tx_bytes += skb->len;
+ lb_stats->tx_bytes = lb_stats->rx_bytes;
lb_stats->rx_packets++;
- lb_stats->tx_packets++;
+ lb_stats->tx_packets = lb_stats->rx_packets;
put_cpu();
netif_rx(skb);
@@ -208,9 +211,12 @@
.type = ARPHRD_LOOPBACK, /* 0x0001*/
.rebuild_header = eth_rebuild_header,
.flags = IFF_LOOPBACK,
- .features = NETIF_F_SG|NETIF_F_FRAGLIST
- |NETIF_F_NO_CSUM|NETIF_F_HIGHDMA
- |NETIF_F_LLTX,
+ .features = NETIF_F_SG | NETIF_F_FRAGLIST
+#ifdef LOOPBACK_TSO
+ | NETIF_F_TSO
+#endif
+ | NETIF_F_NO_CSUM | NETIF_F_HIGHDMA
+ | NETIF_F_LLTX,
.ethtool_ops = &loopback_ethtool_ops,
};
diff --git a/drivers/net/macsonic.c b/drivers/net/macsonic.c
index be28c65..405e183 100644
--- a/drivers/net/macsonic.c
+++ b/drivers/net/macsonic.c
@@ -1,6 +1,12 @@
/*
* macsonic.c
*
+ * (C) 2005 Finn Thain
+ *
+ * Converted to DMA API, converted to unified driver model, made it work as
+ * a module again, and from the mac68k project, introduced more 32-bit cards
+ * and dhd's support for 16-bit cards.
+ *
* (C) 1998 Alan Cox
*
* Debugging Andreas Ehliar, Michael Schmitz
@@ -26,8 +32,8 @@
*/
#include <linux/kernel.h>
+#include <linux/module.h>
#include <linux/types.h>
-#include <linux/ctype.h>
#include <linux/fcntl.h>
#include <linux/interrupt.h>
#include <linux/init.h>
@@ -41,8 +47,8 @@
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/skbuff.h>
-#include <linux/module.h>
-#include <linux/bitops.h>
+#include <linux/device.h>
+#include <linux/dma-mapping.h>
#include <asm/bootinfo.h>
#include <asm/system.h>
@@ -54,25 +60,28 @@
#include <asm/macints.h>
#include <asm/mac_via.h>
-#define SREGS_PAD(n) u16 n;
+static char mac_sonic_string[] = "macsonic";
+static struct platform_device *mac_sonic_device;
#include "sonic.h"
-#define SONIC_READ(reg) \
- nubus_readl(base_addr+(reg))
-#define SONIC_WRITE(reg,val) \
- nubus_writel((val), base_addr+(reg))
-#define sonic_read(dev, reg) \
- nubus_readl((dev)->base_addr+(reg))
-#define sonic_write(dev, reg, val) \
- nubus_writel((val), (dev)->base_addr+(reg))
+/* These should basically be bus-size and endian independent (since
+ the SONIC is at least smart enough that it uses the same endianness
+ as the host, unlike certain less enlightened Macintosh NICs) */
+#define SONIC_READ(reg) (nubus_readw(dev->base_addr + (reg * 4) \
+ + lp->reg_offset))
+#define SONIC_WRITE(reg,val) (nubus_writew(val, dev->base_addr + (reg * 4) \
+ + lp->reg_offset))
+/* use 0 for production, 1 for verification, >1 for debug */
+#ifdef SONIC_DEBUG
+static unsigned int sonic_debug = SONIC_DEBUG;
+#else
+static unsigned int sonic_debug = 1;
+#endif
-static int sonic_debug;
static int sonic_version_printed;
-static int reg_offset;
-
extern int mac_onboard_sonic_probe(struct net_device* dev);
extern int mac_nubus_sonic_probe(struct net_device* dev);
@@ -108,40 +117,6 @@
#define SONIC_READ_PROM(addr) nubus_readb(prom_addr+addr)
-struct net_device * __init macsonic_probe(int unit)
-{
- struct net_device *dev = alloc_etherdev(0);
- int err;
-
- if (!dev)
- return ERR_PTR(-ENOMEM);
-
- if (unit >= 0)
- sprintf(dev->name, "eth%d", unit);
-
- SET_MODULE_OWNER(dev);
-
- /* This will catch fatal stuff like -ENOMEM as well as success */
- err = mac_onboard_sonic_probe(dev);
- if (err == 0)
- goto found;
- if (err != -ENODEV)
- goto out;
- err = mac_nubus_sonic_probe(dev);
- if (err)
- goto out;
-found:
- err = register_netdev(dev);
- if (err)
- goto out1;
- return dev;
-out1:
- kfree(dev->priv);
-out:
- free_netdev(dev);
- return ERR_PTR(err);
-}
-
/*
* For reversing the PROM address
*/
@@ -160,103 +135,55 @@
int __init macsonic_init(struct net_device* dev)
{
- struct sonic_local* lp = NULL;
- int i;
+ struct sonic_local* lp = netdev_priv(dev);
/* Allocate the entire chunk of memory for the descriptors.
Note that this cannot cross a 64K boundary. */
- for (i = 0; i < 20; i++) {
- unsigned long desc_base, desc_top;
- if((lp = kmalloc(sizeof(struct sonic_local), GFP_KERNEL | GFP_DMA)) == NULL) {
- printk(KERN_ERR "%s: couldn't allocate descriptor buffers\n", dev->name);
- return -ENOMEM;
- }
-
- desc_base = (unsigned long) lp;
- desc_top = desc_base + sizeof(struct sonic_local);
- if ((desc_top & 0xffff) >= (desc_base & 0xffff))
- break;
- /* Hmm. try again (FIXME: does this actually work?) */
- kfree(lp);
- printk(KERN_DEBUG
- "%s: didn't get continguous chunk [%08lx - %08lx], trying again\n",
- dev->name, desc_base, desc_top);
- }
-
- if (lp == NULL) {
- printk(KERN_ERR "%s: tried 20 times to allocate descriptor buffers, giving up.\n",
- dev->name);
+ if ((lp->descriptors = dma_alloc_coherent(lp->device,
+ SIZEOF_SONIC_DESC * SONIC_BUS_SCALE(lp->dma_bitmode),
+ &lp->descriptors_laddr, GFP_KERNEL)) == NULL) {
+ printk(KERN_ERR "%s: couldn't alloc DMA memory for descriptors.\n", lp->device->bus_id);
return -ENOMEM;
- }
-
- dev->priv = lp;
-
-#if 0
- /* this code is only here as a curiousity... mainly, where the
- fuck did SONIC_BUS_SCALE come from, and what was it supposed
- to do? the normal allocation works great for 32 bit stuffs.. */
+ }
/* Now set up the pointers to point to the appropriate places */
- lp->cda = lp->sonic_desc;
- lp->tda = lp->cda + (SIZEOF_SONIC_CDA * SONIC_BUS_SCALE(lp->dma_bitmode));
+ lp->cda = lp->descriptors;
+ lp->tda = lp->cda + (SIZEOF_SONIC_CDA
+ * SONIC_BUS_SCALE(lp->dma_bitmode));
lp->rda = lp->tda + (SIZEOF_SONIC_TD * SONIC_NUM_TDS
- * SONIC_BUS_SCALE(lp->dma_bitmode));
+ * SONIC_BUS_SCALE(lp->dma_bitmode));
lp->rra = lp->rda + (SIZEOF_SONIC_RD * SONIC_NUM_RDS
- * SONIC_BUS_SCALE(lp->dma_bitmode));
+ * SONIC_BUS_SCALE(lp->dma_bitmode));
-#endif
-
- memset(lp, 0, sizeof(struct sonic_local));
-
- lp->cda_laddr = (unsigned int)&(lp->cda);
- lp->tda_laddr = (unsigned int)lp->tda;
- lp->rra_laddr = (unsigned int)lp->rra;
- lp->rda_laddr = (unsigned int)lp->rda;
-
- /* FIXME, maybe we should use skbs */
- if ((lp->rba = (char *)
- kmalloc(SONIC_NUM_RRS * SONIC_RBSIZE, GFP_KERNEL | GFP_DMA)) == NULL) {
- printk(KERN_ERR "%s: couldn't allocate receive buffers\n", dev->name);
- dev->priv = NULL;
- kfree(lp);
- return -ENOMEM;
- }
-
- lp->rba_laddr = (unsigned int)lp->rba;
-
- {
- int rs, ds;
-
- /* almost always 12*4096, but let's not take chances */
- rs = ((SONIC_NUM_RRS * SONIC_RBSIZE + 4095) / 4096) * 4096;
- /* almost always under a page, but let's not take chances */
- ds = ((sizeof(struct sonic_local) + 4095) / 4096) * 4096;
- kernel_set_cachemode(lp->rba, rs, IOMAP_NOCACHE_SER);
- kernel_set_cachemode(lp, ds, IOMAP_NOCACHE_SER);
- }
-
-#if 0
- flush_cache_all();
-#endif
+ lp->cda_laddr = lp->descriptors_laddr;
+ lp->tda_laddr = lp->cda_laddr + (SIZEOF_SONIC_CDA
+ * SONIC_BUS_SCALE(lp->dma_bitmode));
+ lp->rda_laddr = lp->tda_laddr + (SIZEOF_SONIC_TD * SONIC_NUM_TDS
+ * SONIC_BUS_SCALE(lp->dma_bitmode));
+ lp->rra_laddr = lp->rda_laddr + (SIZEOF_SONIC_RD * SONIC_NUM_RDS
+ * SONIC_BUS_SCALE(lp->dma_bitmode));
dev->open = sonic_open;
dev->stop = sonic_close;
dev->hard_start_xmit = sonic_send_packet;
dev->get_stats = sonic_get_stats;
dev->set_multicast_list = &sonic_multicast_list;
+ dev->tx_timeout = sonic_tx_timeout;
+ dev->watchdog_timeo = TX_TIMEOUT;
/*
* clear tally counter
*/
- sonic_write(dev, SONIC_CRCT, 0xffff);
- sonic_write(dev, SONIC_FAET, 0xffff);
- sonic_write(dev, SONIC_MPT, 0xffff);
+ SONIC_WRITE(SONIC_CRCT, 0xffff);
+ SONIC_WRITE(SONIC_FAET, 0xffff);
+ SONIC_WRITE(SONIC_MPT, 0xffff);
return 0;
}
int __init mac_onboard_sonic_ethernet_addr(struct net_device* dev)
{
+ struct sonic_local *lp = netdev_priv(dev);
const int prom_addr = ONBOARD_SONIC_PROM_BASE;
int i;
@@ -270,6 +197,7 @@
why this is so. */
if (memcmp(dev->dev_addr, "\x08\x00\x07", 3) &&
memcmp(dev->dev_addr, "\x00\xA0\x40", 3) &&
+ memcmp(dev->dev_addr, "\x00\x80\x19", 3) &&
memcmp(dev->dev_addr, "\x00\x05\x02", 3))
bit_reverse_addr(dev->dev_addr);
else
@@ -281,22 +209,23 @@
the card... */
if (memcmp(dev->dev_addr, "\x08\x00\x07", 3) &&
memcmp(dev->dev_addr, "\x00\xA0\x40", 3) &&
+ memcmp(dev->dev_addr, "\x00\x80\x19", 3) &&
memcmp(dev->dev_addr, "\x00\x05\x02", 3))
{
unsigned short val;
printk(KERN_INFO "macsonic: PROM seems to be wrong, trying CAM entry 15\n");
- sonic_write(dev, SONIC_CMD, SONIC_CR_RST);
- sonic_write(dev, SONIC_CEP, 15);
+ SONIC_WRITE(SONIC_CMD, SONIC_CR_RST);
+ SONIC_WRITE(SONIC_CEP, 15);
- val = sonic_read(dev, SONIC_CAP2);
+ val = SONIC_READ(SONIC_CAP2);
dev->dev_addr[5] = val >> 8;
dev->dev_addr[4] = val & 0xff;
- val = sonic_read(dev, SONIC_CAP1);
+ val = SONIC_READ(SONIC_CAP1);
dev->dev_addr[3] = val >> 8;
dev->dev_addr[2] = val & 0xff;
- val = sonic_read(dev, SONIC_CAP0);
+ val = SONIC_READ(SONIC_CAP0);
dev->dev_addr[1] = val >> 8;
dev->dev_addr[0] = val & 0xff;
@@ -311,6 +240,7 @@
if (memcmp(dev->dev_addr, "\x08\x00\x07", 3) &&
memcmp(dev->dev_addr, "\x00\xA0\x40", 3) &&
+ memcmp(dev->dev_addr, "\x00\x80\x19", 3) &&
memcmp(dev->dev_addr, "\x00\x05\x02", 3))
{
/*
@@ -325,8 +255,9 @@
{
/* Bwahahaha */
static int once_is_more_than_enough;
- int i;
- int dma_bitmode;
+ struct sonic_local* lp = netdev_priv(dev);
+ int sr;
+ int commslot = 0;
if (once_is_more_than_enough)
return -ENODEV;
@@ -335,20 +266,18 @@
if (!MACH_IS_MAC)
return -ENODEV;
- printk(KERN_INFO "Checking for internal Macintosh ethernet (SONIC).. ");
-
if (macintosh_config->ether_type != MAC_ETHER_SONIC)
- {
- printk("none.\n");
return -ENODEV;
- }
-
+
+ printk(KERN_INFO "Checking for internal Macintosh ethernet (SONIC).. ");
+
/* Bogus probing, on the models which may or may not have
Ethernet (BTW, the Ethernet *is* always at the same
address, and nothing else lives there, at least if Apple's
documentation is to be believed) */
if (macintosh_config->ident == MAC_MODEL_Q630 ||
macintosh_config->ident == MAC_MODEL_P588 ||
+ macintosh_config->ident == MAC_MODEL_P575 ||
macintosh_config->ident == MAC_MODEL_C610) {
unsigned long flags;
int card_present;
@@ -361,13 +290,13 @@
printk("none.\n");
return -ENODEV;
}
+ commslot = 1;
}
printk("yes\n");
- /* Danger! My arms are flailing wildly! You *must* set this
- before using sonic_read() */
-
+ /* Danger! My arms are flailing wildly! You *must* set lp->reg_offset
+ * and dev->base_addr before using SONIC_READ() or SONIC_WRITE() */
dev->base_addr = ONBOARD_SONIC_REGISTERS;
if (via_alt_mapping)
dev->irq = IRQ_AUTO_3;
@@ -379,84 +308,66 @@
sonic_version_printed = 1;
}
printk(KERN_INFO "%s: onboard / comm-slot SONIC at 0x%08lx\n",
- dev->name, dev->base_addr);
-
- /* Now do a song and dance routine in an attempt to determine
- the bus width */
+ lp->device->bus_id, dev->base_addr);
/* The PowerBook's SONIC is 16 bit always. */
if (macintosh_config->ident == MAC_MODEL_PB520) {
- reg_offset = 0;
- dma_bitmode = 0;
- } else if (macintosh_config->ident == MAC_MODEL_C610) {
- reg_offset = 0;
- dma_bitmode = 1;
- } else {
+ lp->reg_offset = 0;
+ lp->dma_bitmode = SONIC_BITMODE16;
+ sr = SONIC_READ(SONIC_SR);
+ } else if (commslot) {
/* Some of the comm-slot cards are 16 bit. But some
- of them are not. The 32-bit cards use offset 2 and
- pad with zeroes or sometimes ones (I think...)
- Therefore, if we try offset 0 and get a silicon
- revision of 0, we assume 16 bit. */
- int sr;
+ of them are not. The 32-bit cards use offset 2 and
+ have known revisions, we try reading the revision
+ register at offset 2, if we don't get a known revision
+ we assume 16 bit at offset 0. */
+ lp->reg_offset = 2;
+ lp->dma_bitmode = SONIC_BITMODE16;
- /* Technically this is not necessary since we zeroed
- it above */
- reg_offset = 0;
- dma_bitmode = 0;
- sr = sonic_read(dev, SONIC_SR);
- if (sr == 0 || sr == 0xffff) {
- reg_offset = 2;
- /* 83932 is 0x0004, 83934 is 0x0100 or 0x0101 */
- sr = sonic_read(dev, SONIC_SR);
- dma_bitmode = 1;
-
+ sr = SONIC_READ(SONIC_SR);
+ if (sr == 0x0004 || sr == 0x0006 || sr == 0x0100 || sr == 0x0101)
+ /* 83932 is 0x0004 or 0x0006, 83934 is 0x0100 or 0x0101 */
+ lp->dma_bitmode = SONIC_BITMODE32;
+ else {
+ lp->dma_bitmode = SONIC_BITMODE16;
+ lp->reg_offset = 0;
+ sr = SONIC_READ(SONIC_SR);
}
- printk(KERN_INFO
- "%s: revision 0x%04x, using %d bit DMA and register offset %d\n",
- dev->name, sr, dma_bitmode?32:16, reg_offset);
+ } else {
+ /* All onboard cards are at offset 2 with 32 bit DMA. */
+ lp->reg_offset = 2;
+ lp->dma_bitmode = SONIC_BITMODE32;
+ sr = SONIC_READ(SONIC_SR);
}
-
+ printk(KERN_INFO
+ "%s: revision 0x%04x, using %d bit DMA and register offset %d\n",
+ lp->device->bus_id, sr, lp->dma_bitmode?32:16, lp->reg_offset);
- /* this carries my sincere apologies -- by the time I got to updating
- the driver, support for "reg_offsets" appeares nowhere in the sonic
- code, going back for over a year. Fortunately, my Mac does't seem
- to use whatever this was.
+#if 0 /* This is sometimes useful to find out how MacOS configured the card. */
+ printk(KERN_INFO "%s: DCR: 0x%04x, DCR2: 0x%04x\n", lp->device->bus_id,
+ SONIC_READ(SONIC_DCR) & 0xffff, SONIC_READ(SONIC_DCR2) & 0xffff);
+#endif
- If you know how this is supposed to be implemented, either fix it,
- or contact me (sammy@oh.verio.com) to explain what it is. --Sam */
-
- if(reg_offset) {
- printk("%s: register offset unsupported. please fix this if you know what it is.\n", dev->name);
- return -ENODEV;
- }
-
/* Software reset, then initialize control registers. */
- sonic_write(dev, SONIC_CMD, SONIC_CR_RST);
- sonic_write(dev, SONIC_DCR, SONIC_DCR_BMS |
- SONIC_DCR_RFT1 | SONIC_DCR_TFT0 | SONIC_DCR_EXBUS |
- (dma_bitmode ? SONIC_DCR_DW : 0));
+ SONIC_WRITE(SONIC_CMD, SONIC_CR_RST);
+
+ SONIC_WRITE(SONIC_DCR, SONIC_DCR_EXBUS | SONIC_DCR_BMS |
+ SONIC_DCR_RFT1 | SONIC_DCR_TFT0 |
+ (lp->dma_bitmode ? SONIC_DCR_DW : 0));
/* This *must* be written back to in order to restore the
- extended programmable output bits */
- sonic_write(dev, SONIC_DCR2, 0);
+ * extended programmable output bits, as it may not have been
+ * initialised since the hardware reset. */
+ SONIC_WRITE(SONIC_DCR2, 0);
/* Clear *and* disable interrupts to be on the safe side */
- sonic_write(dev, SONIC_ISR,0x7fff);
- sonic_write(dev, SONIC_IMR,0);
+ SONIC_WRITE(SONIC_IMR, 0);
+ SONIC_WRITE(SONIC_ISR, 0x7fff);
/* Now look for the MAC address. */
if (mac_onboard_sonic_ethernet_addr(dev) != 0)
return -ENODEV;
- printk(KERN_INFO "MAC ");
- for (i = 0; i < 6; i++) {
- printk("%2.2x", dev->dev_addr[i]);
- if (i < 5)
- printk(":");
- }
-
- printk(" IRQ %d\n", dev->irq);
-
/* Shared init code */
return macsonic_init(dev);
}
@@ -468,8 +379,10 @@
int i;
for(i = 0; i < 6; i++)
dev->dev_addr[i] = SONIC_READ_PROM(i);
- /* For now we are going to assume that they're all bit-reversed */
- bit_reverse_addr(dev->dev_addr);
+
+ /* Some of the addresses are bit-reversed */
+ if (id != MACSONIC_DAYNA)
+ bit_reverse_addr(dev->dev_addr);
return 0;
}
@@ -487,6 +400,15 @@
else
return MACSONIC_APPLE;
}
+
+ if (ndev->dr_hw == NUBUS_DRHW_SMC9194 &&
+ ndev->dr_sw == NUBUS_DRSW_DAYNA)
+ return MACSONIC_DAYNA;
+
+ if (ndev->dr_hw == NUBUS_DRHW_SONIC_LC &&
+ ndev->dr_sw == 0) { /* huh? */
+ return MACSONIC_APPLE16;
+ }
return -1;
}
@@ -494,12 +416,12 @@
{
static int slots;
struct nubus_dev* ndev = NULL;
+ struct sonic_local* lp = netdev_priv(dev);
unsigned long base_addr, prom_addr;
u16 sonic_dcr;
- int id;
- int i;
- int dma_bitmode;
-
+ int id = -1;
+ int reg_offset, dma_bitmode;
+
/* Find the first SONIC that hasn't been initialized already */
while ((ndev = nubus_find_type(NUBUS_CAT_NETWORK,
NUBUS_TYPE_ETHERNET, ndev)) != NULL)
@@ -521,51 +443,52 @@
case MACSONIC_DUODOCK:
base_addr = ndev->board->slot_addr + DUODOCK_SONIC_REGISTERS;
prom_addr = ndev->board->slot_addr + DUODOCK_SONIC_PROM_BASE;
- sonic_dcr = SONIC_DCR_EXBUS | SONIC_DCR_RFT0 | SONIC_DCR_RFT1
- | SONIC_DCR_TFT0;
+ sonic_dcr = SONIC_DCR_EXBUS | SONIC_DCR_RFT0 | SONIC_DCR_RFT1 |
+ SONIC_DCR_TFT0;
reg_offset = 2;
- dma_bitmode = 1;
+ dma_bitmode = SONIC_BITMODE32;
break;
case MACSONIC_APPLE:
base_addr = ndev->board->slot_addr + APPLE_SONIC_REGISTERS;
prom_addr = ndev->board->slot_addr + APPLE_SONIC_PROM_BASE;
sonic_dcr = SONIC_DCR_BMS | SONIC_DCR_RFT1 | SONIC_DCR_TFT0;
reg_offset = 0;
- dma_bitmode = 1;
+ dma_bitmode = SONIC_BITMODE32;
break;
case MACSONIC_APPLE16:
base_addr = ndev->board->slot_addr + APPLE_SONIC_REGISTERS;
prom_addr = ndev->board->slot_addr + APPLE_SONIC_PROM_BASE;
- sonic_dcr = SONIC_DCR_EXBUS
- | SONIC_DCR_RFT1 | SONIC_DCR_TFT0
- | SONIC_DCR_PO1 | SONIC_DCR_BMS;
+ sonic_dcr = SONIC_DCR_EXBUS | SONIC_DCR_RFT1 | SONIC_DCR_TFT0 |
+ SONIC_DCR_PO1 | SONIC_DCR_BMS;
reg_offset = 0;
- dma_bitmode = 0;
+ dma_bitmode = SONIC_BITMODE16;
break;
case MACSONIC_DAYNALINK:
base_addr = ndev->board->slot_addr + APPLE_SONIC_REGISTERS;
prom_addr = ndev->board->slot_addr + DAYNALINK_PROM_BASE;
- sonic_dcr = SONIC_DCR_RFT1 | SONIC_DCR_TFT0
- | SONIC_DCR_PO1 | SONIC_DCR_BMS;
+ sonic_dcr = SONIC_DCR_RFT1 | SONIC_DCR_TFT0 |
+ SONIC_DCR_PO1 | SONIC_DCR_BMS;
reg_offset = 0;
- dma_bitmode = 0;
+ dma_bitmode = SONIC_BITMODE16;
break;
case MACSONIC_DAYNA:
base_addr = ndev->board->slot_addr + DAYNA_SONIC_REGISTERS;
prom_addr = ndev->board->slot_addr + DAYNA_SONIC_MAC_ADDR;
- sonic_dcr = SONIC_DCR_BMS
- | SONIC_DCR_RFT1 | SONIC_DCR_TFT0 | SONIC_DCR_PO1;
+ sonic_dcr = SONIC_DCR_BMS |
+ SONIC_DCR_RFT1 | SONIC_DCR_TFT0 | SONIC_DCR_PO1;
reg_offset = 0;
- dma_bitmode = 0;
+ dma_bitmode = SONIC_BITMODE16;
break;
default:
printk(KERN_ERR "macsonic: WTF, id is %d\n", id);
return -ENODEV;
}
- /* Danger! My arms are flailing wildly! You *must* set this
- before using sonic_read() */
+ /* Danger! My arms are flailing wildly! You *must* set lp->reg_offset
+ * and dev->base_addr before using SONIC_READ() or SONIC_WRITE() */
dev->base_addr = base_addr;
+ lp->reg_offset = reg_offset;
+ lp->dma_bitmode = dma_bitmode;
dev->irq = SLOT2IRQ(ndev->board->slot);
if (!sonic_version_printed) {
@@ -573,29 +496,66 @@
sonic_version_printed = 1;
}
printk(KERN_INFO "%s: %s in slot %X\n",
- dev->name, ndev->board->name, ndev->board->slot);
+ lp->device->bus_id, ndev->board->name, ndev->board->slot);
printk(KERN_INFO "%s: revision 0x%04x, using %d bit DMA and register offset %d\n",
- dev->name, sonic_read(dev, SONIC_SR), dma_bitmode?32:16, reg_offset);
+ lp->device->bus_id, SONIC_READ(SONIC_SR), dma_bitmode?32:16, reg_offset);
- if(reg_offset) {
- printk("%s: register offset unsupported. please fix this if you know what it is.\n", dev->name);
- return -ENODEV;
- }
+#if 0 /* This is sometimes useful to find out how MacOS configured the card. */
+ printk(KERN_INFO "%s: DCR: 0x%04x, DCR2: 0x%04x\n", lp->device->bus_id,
+ SONIC_READ(SONIC_DCR) & 0xffff, SONIC_READ(SONIC_DCR2) & 0xffff);
+#endif
/* Software reset, then initialize control registers. */
- sonic_write(dev, SONIC_CMD, SONIC_CR_RST);
- sonic_write(dev, SONIC_DCR, sonic_dcr
- | (dma_bitmode ? SONIC_DCR_DW : 0));
+ SONIC_WRITE(SONIC_CMD, SONIC_CR_RST);
+ SONIC_WRITE(SONIC_DCR, sonic_dcr | (dma_bitmode ? SONIC_DCR_DW : 0));
+ /* This *must* be written back to in order to restore the
+ * extended programmable output bits, since it may not have been
+ * initialised since the hardware reset. */
+ SONIC_WRITE(SONIC_DCR2, 0);
/* Clear *and* disable interrupts to be on the safe side */
- sonic_write(dev, SONIC_ISR,0x7fff);
- sonic_write(dev, SONIC_IMR,0);
+ SONIC_WRITE(SONIC_IMR, 0);
+ SONIC_WRITE(SONIC_ISR, 0x7fff);
/* Now look for the MAC address. */
if (mac_nubus_sonic_ethernet_addr(dev, prom_addr, id) != 0)
return -ENODEV;
- printk(KERN_INFO "MAC ");
+ /* Shared init code */
+ return macsonic_init(dev);
+}
+
+static int __init mac_sonic_probe(struct device *device)
+{
+ struct net_device *dev;
+ struct sonic_local *lp;
+ int err;
+ int i;
+
+ dev = alloc_etherdev(sizeof(struct sonic_local));
+ if (!dev)
+ return -ENOMEM;
+
+ lp = netdev_priv(dev);
+ lp->device = device;
+ SET_NETDEV_DEV(dev, device);
+ SET_MODULE_OWNER(dev);
+
+ /* This will catch fatal stuff like -ENOMEM as well as success */
+ err = mac_onboard_sonic_probe(dev);
+ if (err == 0)
+ goto found;
+ if (err != -ENODEV)
+ goto out;
+ err = mac_nubus_sonic_probe(dev);
+ if (err)
+ goto out;
+found:
+ err = register_netdev(dev);
+ if (err)
+ goto out;
+
+ printk("%s: MAC ", dev->name);
for (i = 0; i < 6; i++) {
printk("%2.2x", dev->dev_addr[i]);
if (i < 5)
@@ -603,55 +563,95 @@
}
printk(" IRQ %d\n", dev->irq);
- /* Shared init code */
- return macsonic_init(dev);
+ return 0;
+
+out:
+ free_netdev(dev);
+
+ return err;
}
-#ifdef MODULE
-static struct net_device *dev_macsonic;
-
-MODULE_PARM(sonic_debug, "i");
+MODULE_DESCRIPTION("Macintosh SONIC ethernet driver");
+module_param(sonic_debug, int, 0);
MODULE_PARM_DESC(sonic_debug, "macsonic debug level (1-4)");
-int
-init_module(void)
-{
- dev_macsonic = macsonic_probe(-1);
- if (IS_ERR(dev_macsonic)) {
- printk(KERN_WARNING "macsonic.c: No card found\n");
- return PTR_ERR(dev_macsonic);
- }
- return 0;
-}
-
-void
-cleanup_module(void)
-{
- unregister_netdev(dev_macsonic);
- kfree(dev_macsonic->priv);
- free_netdev(dev_macsonic);
-}
-#endif /* MODULE */
-
-
-#define vdma_alloc(foo, bar) ((u32)foo)
-#define vdma_free(baz)
-#define sonic_chiptomem(bat) (bat)
-#define PHYSADDR(quux) (quux)
-#define CPHYSADDR(quux) (quux)
-
-#define sonic_request_irq request_irq
-#define sonic_free_irq free_irq
+#define SONIC_IRQ_FLAG IRQ_FLG_FAST
#include "sonic.c"
-/*
- * Local variables:
- * compile-command: "m68k-linux-gcc -D__KERNEL__ -I../../include -Wall -Wstrict-prototypes -O2 -fomit-frame-pointer -pipe -fno-strength-reduce -ffixed-a2 -DMODULE -DMODVERSIONS -include ../../include/linux/modversions.h -c -o macsonic.o macsonic.c"
- * version-control: t
- * kept-new-versions: 5
- * c-indent-level: 8
- * tab-width: 8
- * End:
- *
- */
+static int __devexit mac_sonic_device_remove (struct device *device)
+{
+ struct net_device *dev = device->driver_data;
+ struct sonic_local* lp = netdev_priv(dev);
+
+ unregister_netdev (dev);
+ dma_free_coherent(lp->device, SIZEOF_SONIC_DESC * SONIC_BUS_SCALE(lp->dma_bitmode),
+ lp->descriptors, lp->descriptors_laddr);
+ free_netdev (dev);
+
+ return 0;
+}
+
+static struct device_driver mac_sonic_driver = {
+ .name = mac_sonic_string,
+ .bus = &platform_bus_type,
+ .probe = mac_sonic_probe,
+ .remove = __devexit_p(mac_sonic_device_remove),
+};
+
+static void mac_sonic_platform_release(struct device *device)
+{
+ struct platform_device *pldev;
+
+ /* free device */
+ pldev = to_platform_device (device);
+ kfree (pldev);
+}
+
+static int __init mac_sonic_init_module(void)
+{
+ struct platform_device *pldev;
+ int err;
+
+ if ((err = driver_register(&mac_sonic_driver))) {
+ printk(KERN_ERR "Driver registration failed\n");
+ return err;
+ }
+
+ mac_sonic_device = NULL;
+
+ if (!(pldev = kmalloc (sizeof (*pldev), GFP_KERNEL))) {
+ goto out_unregister;
+ }
+
+ memset(pldev, 0, sizeof (*pldev));
+ pldev->name = mac_sonic_string;
+ pldev->id = 0;
+ pldev->dev.release = mac_sonic_platform_release;
+ mac_sonic_device = pldev;
+
+ if (platform_device_register (pldev)) {
+ kfree(pldev);
+ mac_sonic_device = NULL;
+ }
+
+ return 0;
+
+out_unregister:
+ platform_device_unregister(pldev);
+
+ return -ENOMEM;
+}
+
+static void __exit mac_sonic_cleanup_module(void)
+{
+ driver_unregister(&mac_sonic_driver);
+
+ if (mac_sonic_device) {
+ platform_device_unregister(mac_sonic_device);
+ mac_sonic_device = NULL;
+ }
+}
+
+module_init(mac_sonic_init_module);
+module_exit(mac_sonic_cleanup_module);
diff --git a/drivers/net/mv643xx_eth.c b/drivers/net/mv643xx_eth.c
index 0405e1f..fb6b232 100644
--- a/drivers/net/mv643xx_eth.c
+++ b/drivers/net/mv643xx_eth.c
@@ -1157,16 +1157,20 @@
if (!skb_shinfo(skb)->nr_frags) {
linear:
if (skb->ip_summed != CHECKSUM_HW) {
+ /* Errata BTS #50, IHL must be 5 if no HW checksum */
pkt_info.cmd_sts = ETH_TX_ENABLE_INTERRUPT |
- ETH_TX_FIRST_DESC | ETH_TX_LAST_DESC;
+ ETH_TX_FIRST_DESC |
+ ETH_TX_LAST_DESC |
+ 5 << ETH_TX_IHL_SHIFT;
pkt_info.l4i_chk = 0;
} else {
- u32 ipheader = skb->nh.iph->ihl << 11;
pkt_info.cmd_sts = ETH_TX_ENABLE_INTERRUPT |
- ETH_TX_FIRST_DESC | ETH_TX_LAST_DESC |
- ETH_GEN_TCP_UDP_CHECKSUM |
- ETH_GEN_IP_V_4_CHECKSUM | ipheader;
+ ETH_TX_FIRST_DESC |
+ ETH_TX_LAST_DESC |
+ ETH_GEN_TCP_UDP_CHECKSUM |
+ ETH_GEN_IP_V_4_CHECKSUM |
+ skb->nh.iph->ihl << ETH_TX_IHL_SHIFT;
/* CPU already calculated pseudo header checksum. */
if (skb->nh.iph->protocol == IPPROTO_UDP) {
pkt_info.cmd_sts |= ETH_UDP_FRAME;
@@ -1193,7 +1197,6 @@
stats->tx_bytes += pkt_info.byte_cnt;
} else {
unsigned int frag;
- u32 ipheader;
/* Since hardware can't handle unaligned fragments smaller
* than 9 bytes, if we find any, we linearize the skb
@@ -1222,12 +1225,16 @@
DMA_TO_DEVICE);
pkt_info.l4i_chk = 0;
pkt_info.return_info = 0;
- pkt_info.cmd_sts = ETH_TX_FIRST_DESC;
- if (skb->ip_summed == CHECKSUM_HW) {
- ipheader = skb->nh.iph->ihl << 11;
- pkt_info.cmd_sts |= ETH_GEN_TCP_UDP_CHECKSUM |
- ETH_GEN_IP_V_4_CHECKSUM | ipheader;
+ if (skb->ip_summed != CHECKSUM_HW)
+ /* Errata BTS #50, IHL must be 5 if no HW checksum */
+ pkt_info.cmd_sts = ETH_TX_FIRST_DESC |
+ 5 << ETH_TX_IHL_SHIFT;
+ else {
+ pkt_info.cmd_sts = ETH_TX_FIRST_DESC |
+ ETH_GEN_TCP_UDP_CHECKSUM |
+ ETH_GEN_IP_V_4_CHECKSUM |
+ skb->nh.iph->ihl << ETH_TX_IHL_SHIFT;
/* CPU already calculated pseudo header checksum. */
if (skb->nh.iph->protocol == IPPROTO_UDP) {
pkt_info.cmd_sts |= ETH_UDP_FRAME;
diff --git a/drivers/net/mv643xx_eth.h b/drivers/net/mv643xx_eth.h
index 57c4f8f..7678b59 100644
--- a/drivers/net/mv643xx_eth.h
+++ b/drivers/net/mv643xx_eth.h
@@ -49,7 +49,7 @@
/* Checksum offload for Tx works for most packets, but
* fails if previous packet sent did not use hw csum
*/
-#undef MV643XX_CHECKSUM_OFFLOAD_TX
+#define MV643XX_CHECKSUM_OFFLOAD_TX
#define MV643XX_NAPI
#define MV643XX_TX_FAST_REFILL
#undef MV643XX_RX_QUEUE_FILL_ON_TASK /* Does not work, yet */
@@ -217,6 +217,8 @@
#define ETH_TX_ENABLE_INTERRUPT (BIT23)
#define ETH_AUTO_MODE (BIT30)
+#define ETH_TX_IHL_SHIFT 11
+
/* typedefs */
typedef enum _eth_func_ret_status {
diff --git a/drivers/net/pci-skeleton.c b/drivers/net/pci-skeleton.c
index 4a391ea..a1ac4bd 100644
--- a/drivers/net/pci-skeleton.c
+++ b/drivers/net/pci-skeleton.c
@@ -486,9 +486,9 @@
MODULE_AUTHOR ("Jeff Garzik <jgarzik@pobox.com>");
MODULE_DESCRIPTION ("Skeleton for a PCI Fast Ethernet driver");
MODULE_LICENSE("GPL");
-MODULE_PARM (multicast_filter_limit, "i");
-MODULE_PARM (max_interrupt_work, "i");
-MODULE_PARM (media, "1-" __MODULE_STRING(8) "i");
+module_param(multicast_filter_limit, int, 0);
+module_param(max_interrupt_work, int, 0);
+module_param_array(media, int, NULL, 0);
MODULE_PARM_DESC (multicast_filter_limit, "pci-skeleton maximum number of filtered multicast addresses");
MODULE_PARM_DESC (max_interrupt_work, "pci-skeleton maximum events handled per interrupt");
MODULE_PARM_DESC (media, "pci-skeleton: Bits 0-3: media type, bit 17: full duplex");
diff --git a/drivers/net/pcmcia/fmvj18x_cs.c b/drivers/net/pcmcia/fmvj18x_cs.c
index 9d8197b..384a736 100644
--- a/drivers/net/pcmcia/fmvj18x_cs.c
+++ b/drivers/net/pcmcia/fmvj18x_cs.c
@@ -134,7 +134,7 @@
u_char mc_filter[8];
} local_info_t;
-#define MC_FILTERBREAK 64
+#define MC_FILTERBREAK 8
/*====================================================================*/
/*
@@ -1012,7 +1012,7 @@
outb(BANK_1U, ioaddr + CONFIG_1);
/* set the multicast table to accept none. */
- for (i = 0; i < 6; i++)
+ for (i = 0; i < 8; i++)
outb(0x00, ioaddr + MAR_ADR + i);
/* Switch to bank 2 (runtime mode) */
@@ -1269,6 +1269,16 @@
u_long flags;
int i;
+ int saved_config_0 = inb(ioaddr + CONFIG_0);
+
+ local_irq_save(flags);
+
+ /* Disable Tx and Rx */
+ if (sram_config == 0)
+ outb(CONFIG0_RST, ioaddr + CONFIG_0);
+ else
+ outb(CONFIG0_RST_1, ioaddr + CONFIG_0);
+
if (dev->flags & IFF_PROMISC) {
/* Unconditionally log net taps. */
printk("%s: Promiscuous mode enabled.\n", dev->name);
@@ -1290,20 +1300,23 @@
for (i = 0, mclist = dev->mc_list; mclist && i < dev->mc_count;
i++, mclist = mclist->next) {
unsigned int bit =
- ether_crc_le(ETH_ALEN, mclist->dmi_addr) & 0x3f;
- mc_filter[bit >> 3] |= (1 << bit);
+ ether_crc_le(ETH_ALEN, mclist->dmi_addr) >> 26;
+ mc_filter[bit >> 3] |= (1 << (bit & 7));
}
+ outb(2, ioaddr + RX_MODE); /* Use normal mode. */
}
- local_irq_save(flags);
if (memcmp(mc_filter, lp->mc_filter, sizeof(mc_filter))) {
int saved_bank = inb(ioaddr + CONFIG_1);
/* Switch to bank 1 and set the multicast table. */
outb(0xe4, ioaddr + CONFIG_1);
for (i = 0; i < 8; i++)
- outb(mc_filter[i], ioaddr + 8 + i);
+ outb(mc_filter[i], ioaddr + MAR_ADR + i);
memcpy(lp->mc_filter, mc_filter, sizeof(mc_filter));
outb(saved_bank, ioaddr + CONFIG_1);
}
+
+ outb(saved_config_0, ioaddr + CONFIG_0);
+
local_irq_restore(flags);
}
diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
new file mode 100644
index 0000000..6a2fe35
--- /dev/null
+++ b/drivers/net/phy/Kconfig
@@ -0,0 +1,57 @@
+#
+# PHY Layer Configuration
+#
+
+menu "PHY device support"
+
+config PHYLIB
+ tristate "PHY Device support and infrastructure"
+ depends on NET_ETHERNET
+ help
+ Ethernet controllers are usually attached to PHY
+ devices. This option provides infrastructure for
+ managing PHY devices.
+
+config PHYCONTROL
+ bool " Support for automatically handling PHY state changes"
+ depends on PHYLIB
+ help
+ Adds code to perform all the work for keeping PHY link
+ state (speed/duplex/etc) up-to-date. Also handles
+ interrupts.
+
+comment "MII PHY device drivers"
+ depends on PHYLIB
+
+config MARVELL_PHY
+ tristate "Drivers for Marvell PHYs"
+ depends on PHYLIB
+ ---help---
+ Currently has a driver for the 88E1011S
+
+config DAVICOM_PHY
+ tristate "Drivers for Davicom PHYs"
+ depends on PHYLIB
+ ---help---
+ Currently supports dm9161e and dm9131
+
+config QSEMI_PHY
+ tristate "Drivers for Quality Semiconductor PHYs"
+ depends on PHYLIB
+ ---help---
+ Currently supports the qs6612
+
+config LXT_PHY
+ tristate "Drivers for the Intel LXT PHYs"
+ depends on PHYLIB
+ ---help---
+ Currently supports the lxt970, lxt971
+
+config CICADA_PHY
+ tristate "Drivers for the Cicada PHYs"
+ depends on PHYLIB
+ ---help---
+ Currently supports the cis8204
+
+endmenu
+
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
new file mode 100644
index 0000000..e4116a5
--- /dev/null
+++ b/drivers/net/phy/Makefile
@@ -0,0 +1,10 @@
+# Makefile for Linux PHY drivers
+
+libphy-objs := phy.o phy_device.o mdio_bus.o
+
+obj-$(CONFIG_PHYLIB) += libphy.o
+obj-$(CONFIG_MARVELL_PHY) += marvell.o
+obj-$(CONFIG_DAVICOM_PHY) += davicom.o
+obj-$(CONFIG_CICADA_PHY) += cicada.o
+obj-$(CONFIG_LXT_PHY) += lxt.o
+obj-$(CONFIG_QSEMI_PHY) += qsemi.o
diff --git a/drivers/net/phy/cicada.c b/drivers/net/phy/cicada.c
new file mode 100644
index 0000000..c47fb2e
--- /dev/null
+++ b/drivers/net/phy/cicada.c
@@ -0,0 +1,134 @@
+/*
+ * drivers/net/phy/cicada.c
+ *
+ * Driver for Cicada PHYs
+ *
+ * Author: Andy Fleming
+ *
+ * Copyright (c) 2004 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+#include <linux/config.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/string.h>
+#include <linux/errno.h>
+#include <linux/unistd.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+#include <linux/spinlock.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/version.h>
+#include <linux/mii.h>
+#include <linux/ethtool.h>
+#include <linux/phy.h>
+
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/uaccess.h>
+
+/* Cicada Extended Control Register 1 */
+#define MII_CIS8201_EXT_CON1 0x17
+#define MII_CIS8201_EXTCON1_INIT 0x0000
+
+/* Cicada Interrupt Mask Register */
+#define MII_CIS8201_IMASK 0x19
+#define MII_CIS8201_IMASK_IEN 0x8000
+#define MII_CIS8201_IMASK_SPEED 0x4000
+#define MII_CIS8201_IMASK_LINK 0x2000
+#define MII_CIS8201_IMASK_DUPLEX 0x1000
+#define MII_CIS8201_IMASK_MASK 0xf000
+
+/* Cicada Interrupt Status Register */
+#define MII_CIS8201_ISTAT 0x1a
+#define MII_CIS8201_ISTAT_STATUS 0x8000
+#define MII_CIS8201_ISTAT_SPEED 0x4000
+#define MII_CIS8201_ISTAT_LINK 0x2000
+#define MII_CIS8201_ISTAT_DUPLEX 0x1000
+
+/* Cicada Auxiliary Control/Status Register */
+#define MII_CIS8201_AUX_CONSTAT 0x1c
+#define MII_CIS8201_AUXCONSTAT_INIT 0x0004
+#define MII_CIS8201_AUXCONSTAT_DUPLEX 0x0020
+#define MII_CIS8201_AUXCONSTAT_SPEED 0x0018
+#define MII_CIS8201_AUXCONSTAT_GBIT 0x0010
+#define MII_CIS8201_AUXCONSTAT_100 0x0008
+
+MODULE_DESCRIPTION("Cicadia PHY driver");
+MODULE_AUTHOR("Andy Fleming");
+MODULE_LICENSE("GPL");
+
+static int cis820x_config_init(struct phy_device *phydev)
+{
+ int err;
+
+ err = phy_write(phydev, MII_CIS8201_AUX_CONSTAT,
+ MII_CIS8201_AUXCONSTAT_INIT);
+
+ if (err < 0)
+ return err;
+
+ err = phy_write(phydev, MII_CIS8201_EXT_CON1,
+ MII_CIS8201_EXTCON1_INIT);
+
+ return err;
+}
+
+static int cis820x_ack_interrupt(struct phy_device *phydev)
+{
+ int err = phy_read(phydev, MII_CIS8201_ISTAT);
+
+ return (err < 0) ? err : 0;
+}
+
+static int cis820x_config_intr(struct phy_device *phydev)
+{
+ int err;
+
+ if(phydev->interrupts == PHY_INTERRUPT_ENABLED)
+ err = phy_write(phydev, MII_CIS8201_IMASK,
+ MII_CIS8201_IMASK_MASK);
+ else
+ err = phy_write(phydev, MII_CIS8201_IMASK, 0);
+
+ return err;
+}
+
+/* Cicada 820x */
+static struct phy_driver cis8204_driver = {
+ .phy_id = 0x000fc440,
+ .name = "Cicada Cis8204",
+ .phy_id_mask = 0x000fffc0,
+ .features = PHY_GBIT_FEATURES,
+ .flags = PHY_HAS_INTERRUPT,
+ .config_init = &cis820x_config_init,
+ .config_aneg = &genphy_config_aneg,
+ .read_status = &genphy_read_status,
+ .ack_interrupt = &cis820x_ack_interrupt,
+ .config_intr = &cis820x_config_intr,
+ .driver = { .owner = THIS_MODULE,},
+};
+
+static int __init cis8204_init(void)
+{
+ return phy_driver_register(&cis8204_driver);
+}
+
+static void __exit cis8204_exit(void)
+{
+ phy_driver_unregister(&cis8204_driver);
+}
+
+module_init(cis8204_init);
+module_exit(cis8204_exit);
diff --git a/drivers/net/phy/davicom.c b/drivers/net/phy/davicom.c
new file mode 100644
index 0000000..6caf499
--- /dev/null
+++ b/drivers/net/phy/davicom.c
@@ -0,0 +1,195 @@
+/*
+ * drivers/net/phy/davicom.c
+ *
+ * Driver for Davicom PHYs
+ *
+ * Author: Andy Fleming
+ *
+ * Copyright (c) 2004 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+#include <linux/config.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/string.h>
+#include <linux/errno.h>
+#include <linux/unistd.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+#include <linux/spinlock.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/version.h>
+#include <linux/mii.h>
+#include <linux/ethtool.h>
+#include <linux/phy.h>
+
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/uaccess.h>
+
+#define MII_DM9161_SCR 0x10
+#define MII_DM9161_SCR_INIT 0x0610
+
+/* DM9161 Interrupt Register */
+#define MII_DM9161_INTR 0x15
+#define MII_DM9161_INTR_PEND 0x8000
+#define MII_DM9161_INTR_DPLX_MASK 0x0800
+#define MII_DM9161_INTR_SPD_MASK 0x0400
+#define MII_DM9161_INTR_LINK_MASK 0x0200
+#define MII_DM9161_INTR_MASK 0x0100
+#define MII_DM9161_INTR_DPLX_CHANGE 0x0010
+#define MII_DM9161_INTR_SPD_CHANGE 0x0008
+#define MII_DM9161_INTR_LINK_CHANGE 0x0004
+#define MII_DM9161_INTR_INIT 0x0000
+#define MII_DM9161_INTR_STOP \
+(MII_DM9161_INTR_DPLX_MASK | MII_DM9161_INTR_SPD_MASK \
+ | MII_DM9161_INTR_LINK_MASK | MII_DM9161_INTR_MASK)
+
+/* DM9161 10BT Configuration/Status */
+#define MII_DM9161_10BTCSR 0x12
+#define MII_DM9161_10BTCSR_INIT 0x7800
+
+MODULE_DESCRIPTION("Davicom PHY driver");
+MODULE_AUTHOR("Andy Fleming");
+MODULE_LICENSE("GPL");
+
+
+#define DM9161_DELAY 1
+static int dm9161_config_intr(struct phy_device *phydev)
+{
+ int temp;
+
+ temp = phy_read(phydev, MII_DM9161_INTR);
+
+ if (temp < 0)
+ return temp;
+
+ if(PHY_INTERRUPT_ENABLED == phydev->interrupts )
+ temp &= ~(MII_DM9161_INTR_STOP);
+ else
+ temp |= MII_DM9161_INTR_STOP;
+
+ temp = phy_write(phydev, MII_DM9161_INTR, temp);
+
+ return temp;
+}
+
+static int dm9161_config_aneg(struct phy_device *phydev)
+{
+ int err;
+
+ /* Isolate the PHY */
+ err = phy_write(phydev, MII_BMCR, BMCR_ISOLATE);
+
+ if (err < 0)
+ return err;
+
+ /* Configure the new settings */
+ err = genphy_config_aneg(phydev);
+
+ if (err < 0)
+ return err;
+
+ return 0;
+}
+
+static int dm9161_config_init(struct phy_device *phydev)
+{
+ int err;
+
+ /* Isolate the PHY */
+ err = phy_write(phydev, MII_BMCR, BMCR_ISOLATE);
+
+ if (err < 0)
+ return err;
+
+ /* Do not bypass the scrambler/descrambler */
+ err = phy_write(phydev, MII_DM9161_SCR, MII_DM9161_SCR_INIT);
+
+ if (err < 0)
+ return err;
+
+ /* Clear 10BTCSR to default */
+ err = phy_write(phydev, MII_DM9161_10BTCSR, MII_DM9161_10BTCSR_INIT);
+
+ if (err < 0)
+ return err;
+
+ /* Reconnect the PHY, and enable Autonegotiation */
+ err = phy_write(phydev, MII_BMCR, BMCR_ANENABLE);
+
+ if (err < 0)
+ return err;
+
+ return 0;
+}
+
+static int dm9161_ack_interrupt(struct phy_device *phydev)
+{
+ int err = phy_read(phydev, MII_DM9161_INTR);
+
+ return (err < 0) ? err : 0;
+}
+
+static struct phy_driver dm9161_driver = {
+ .phy_id = 0x0181b880,
+ .name = "Davicom DM9161E",
+ .phy_id_mask = 0x0ffffff0,
+ .features = PHY_BASIC_FEATURES,
+ .config_init = dm9161_config_init,
+ .config_aneg = dm9161_config_aneg,
+ .read_status = genphy_read_status,
+ .driver = { .owner = THIS_MODULE,},
+};
+
+static struct phy_driver dm9131_driver = {
+ .phy_id = 0x00181b80,
+ .name = "Davicom DM9131",
+ .phy_id_mask = 0x0ffffff0,
+ .features = PHY_BASIC_FEATURES,
+ .flags = PHY_HAS_INTERRUPT,
+ .config_aneg = genphy_config_aneg,
+ .read_status = genphy_read_status,
+ .ack_interrupt = dm9161_ack_interrupt,
+ .config_intr = dm9161_config_intr,
+ .driver = { .owner = THIS_MODULE,},
+};
+
+static int __init davicom_init(void)
+{
+ int ret;
+
+ ret = phy_driver_register(&dm9161_driver);
+ if (ret)
+ goto err1;
+
+ ret = phy_driver_register(&dm9131_driver);
+ if (ret)
+ goto err2;
+ return 0;
+
+ err2:
+ phy_driver_unregister(&dm9161_driver);
+ err1:
+ return ret;
+}
+
+static void __exit davicom_exit(void)
+{
+ phy_driver_unregister(&dm9161_driver);
+ phy_driver_unregister(&dm9131_driver);
+}
+
+module_init(davicom_init);
+module_exit(davicom_exit);
diff --git a/drivers/net/phy/lxt.c b/drivers/net/phy/lxt.c
new file mode 100644
index 0000000..4c84044
--- /dev/null
+++ b/drivers/net/phy/lxt.c
@@ -0,0 +1,179 @@
+/*
+ * drivers/net/phy/lxt.c
+ *
+ * Driver for Intel LXT PHYs
+ *
+ * Author: Andy Fleming
+ *
+ * Copyright (c) 2004 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+#include <linux/config.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/string.h>
+#include <linux/errno.h>
+#include <linux/unistd.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+#include <linux/spinlock.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/version.h>
+#include <linux/mii.h>
+#include <linux/ethtool.h>
+#include <linux/phy.h>
+
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/uaccess.h>
+
+/* The Level one LXT970 is used by many boards */
+
+#define MII_LXT970_IER 17 /* Interrupt Enable Register */
+
+#define MII_LXT970_IER_IEN 0x0002
+
+#define MII_LXT970_ISR 18 /* Interrupt Status Register */
+
+#define MII_LXT970_CONFIG 19 /* Configuration Register */
+
+/* ------------------------------------------------------------------------- */
+/* The Level one LXT971 is used on some of my custom boards */
+
+/* register definitions for the 971 */
+#define MII_LXT971_IER 18 /* Interrupt Enable Register */
+#define MII_LXT971_IER_IEN 0x00f2
+
+#define MII_LXT971_ISR 19 /* Interrupt Status Register */
+
+
+MODULE_DESCRIPTION("Intel LXT PHY driver");
+MODULE_AUTHOR("Andy Fleming");
+MODULE_LICENSE("GPL");
+
+static int lxt970_ack_interrupt(struct phy_device *phydev)
+{
+ int err;
+
+ err = phy_read(phydev, MII_BMSR);
+
+ if (err < 0)
+ return err;
+
+ err = phy_read(phydev, MII_LXT970_ISR);
+
+ if (err < 0)
+ return err;
+
+ return 0;
+}
+
+static int lxt970_config_intr(struct phy_device *phydev)
+{
+ int err;
+
+ if(phydev->interrupts == PHY_INTERRUPT_ENABLED)
+ err = phy_write(phydev, MII_LXT970_IER, MII_LXT970_IER_IEN);
+ else
+ err = phy_write(phydev, MII_LXT970_IER, 0);
+
+ return err;
+}
+
+static int lxt970_config_init(struct phy_device *phydev)
+{
+ int err;
+
+ err = phy_write(phydev, MII_LXT970_CONFIG, 0);
+
+ return err;
+}
+
+
+static int lxt971_ack_interrupt(struct phy_device *phydev)
+{
+ int err = phy_read(phydev, MII_LXT971_ISR);
+
+ if (err < 0)
+ return err;
+
+ return 0;
+}
+
+static int lxt971_config_intr(struct phy_device *phydev)
+{
+ int err;
+
+ if(phydev->interrupts == PHY_INTERRUPT_ENABLED)
+ err = phy_write(phydev, MII_LXT971_IER, MII_LXT971_IER_IEN);
+ else
+ err = phy_write(phydev, MII_LXT971_IER, 0);
+
+ return err;
+}
+
+static struct phy_driver lxt970_driver = {
+ .phy_id = 0x07810000,
+ .name = "LXT970",
+ .phy_id_mask = 0x0fffffff,
+ .features = PHY_BASIC_FEATURES,
+ .flags = PHY_HAS_INTERRUPT,
+ .config_init = lxt970_config_init,
+ .config_aneg = genphy_config_aneg,
+ .read_status = genphy_read_status,
+ .ack_interrupt = lxt970_ack_interrupt,
+ .config_intr = lxt970_config_intr,
+ .driver = { .owner = THIS_MODULE,},
+};
+
+static struct phy_driver lxt971_driver = {
+ .phy_id = 0x0001378e,
+ .name = "LXT971",
+ .phy_id_mask = 0x0fffffff,
+ .features = PHY_BASIC_FEATURES,
+ .flags = PHY_HAS_INTERRUPT,
+ .config_aneg = genphy_config_aneg,
+ .read_status = genphy_read_status,
+ .ack_interrupt = lxt971_ack_interrupt,
+ .config_intr = lxt971_config_intr,
+ .driver = { .owner = THIS_MODULE,},
+};
+
+static int __init lxt_init(void)
+{
+ int ret;
+
+ ret = phy_driver_register(&lxt970_driver);
+ if (ret)
+ goto err1;
+
+ ret = phy_driver_register(&lxt971_driver);
+ if (ret)
+ goto err2;
+ return 0;
+
+ err2:
+ phy_driver_unregister(&lxt970_driver);
+ err1:
+ return ret;
+}
+
+static void __exit lxt_exit(void)
+{
+ phy_driver_unregister(&lxt970_driver);
+ phy_driver_unregister(&lxt971_driver);
+}
+
+module_init(lxt_init);
+module_exit(lxt_exit);
diff --git a/drivers/net/phy/marvell.c b/drivers/net/phy/marvell.c
new file mode 100644
index 0000000..4a72b02
--- /dev/null
+++ b/drivers/net/phy/marvell.c
@@ -0,0 +1,140 @@
+/*
+ * drivers/net/phy/marvell.c
+ *
+ * Driver for Marvell PHYs
+ *
+ * Author: Andy Fleming
+ *
+ * Copyright (c) 2004 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+#include <linux/config.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/string.h>
+#include <linux/errno.h>
+#include <linux/unistd.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+#include <linux/spinlock.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/version.h>
+#include <linux/mii.h>
+#include <linux/ethtool.h>
+#include <linux/phy.h>
+
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/uaccess.h>
+
+#define MII_M1011_IEVENT 0x13
+#define MII_M1011_IEVENT_CLEAR 0x0000
+
+#define MII_M1011_IMASK 0x12
+#define MII_M1011_IMASK_INIT 0x6400
+#define MII_M1011_IMASK_CLEAR 0x0000
+
+MODULE_DESCRIPTION("Marvell PHY driver");
+MODULE_AUTHOR("Andy Fleming");
+MODULE_LICENSE("GPL");
+
+static int marvell_ack_interrupt(struct phy_device *phydev)
+{
+ int err;
+
+ /* Clear the interrupts by reading the reg */
+ err = phy_read(phydev, MII_M1011_IEVENT);
+
+ if (err < 0)
+ return err;
+
+ return 0;
+}
+
+static int marvell_config_intr(struct phy_device *phydev)
+{
+ int err;
+
+ if(phydev->interrupts == PHY_INTERRUPT_ENABLED)
+ err = phy_write(phydev, MII_M1011_IMASK, MII_M1011_IMASK_INIT);
+ else
+ err = phy_write(phydev, MII_M1011_IMASK, MII_M1011_IMASK_CLEAR);
+
+ return err;
+}
+
+static int marvell_config_aneg(struct phy_device *phydev)
+{
+ int err;
+
+ /* The Marvell PHY has an errata which requires
+ * that certain registers get written in order
+ * to restart autonegotiation */
+ err = phy_write(phydev, MII_BMCR, BMCR_RESET);
+
+ if (err < 0)
+ return err;
+
+ err = phy_write(phydev, 0x1d, 0x1f);
+ if (err < 0)
+ return err;
+
+ err = phy_write(phydev, 0x1e, 0x200c);
+ if (err < 0)
+ return err;
+
+ err = phy_write(phydev, 0x1d, 0x5);
+ if (err < 0)
+ return err;
+
+ err = phy_write(phydev, 0x1e, 0);
+ if (err < 0)
+ return err;
+
+ err = phy_write(phydev, 0x1e, 0x100);
+ if (err < 0)
+ return err;
+
+
+ err = genphy_config_aneg(phydev);
+
+ return err;
+}
+
+
+static struct phy_driver m88e1101_driver = {
+ .phy_id = 0x01410c00,
+ .phy_id_mask = 0xffffff00,
+ .name = "Marvell 88E1101",
+ .features = PHY_GBIT_FEATURES,
+ .flags = PHY_HAS_INTERRUPT,
+ .config_aneg = &marvell_config_aneg,
+ .read_status = &genphy_read_status,
+ .ack_interrupt = &marvell_ack_interrupt,
+ .config_intr = &marvell_config_intr,
+ .driver = { .owner = THIS_MODULE,},
+};
+
+static int __init marvell_init(void)
+{
+ return phy_driver_register(&m88e1101_driver);
+}
+
+static void __exit marvell_exit(void)
+{
+ phy_driver_unregister(&m88e1101_driver);
+}
+
+module_init(marvell_init);
+module_exit(marvell_exit);
diff --git a/drivers/net/phy/mdio_bus.c b/drivers/net/phy/mdio_bus.c
new file mode 100644
index 0000000..41f62c0
--- /dev/null
+++ b/drivers/net/phy/mdio_bus.c
@@ -0,0 +1,176 @@
+/*
+ * drivers/net/phy/mdio_bus.c
+ *
+ * MDIO Bus interface
+ *
+ * Author: Andy Fleming
+ *
+ * Copyright (c) 2004 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+#include <linux/config.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/string.h>
+#include <linux/errno.h>
+#include <linux/unistd.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+#include <linux/spinlock.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/version.h>
+#include <linux/mii.h>
+#include <linux/ethtool.h>
+#include <linux/phy.h>
+
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/uaccess.h>
+
+/* mdiobus_register
+ *
+ * description: Called by a bus driver to bring up all the PHYs
+ * on a given bus, and attach them to the bus
+ */
+int mdiobus_register(struct mii_bus *bus)
+{
+ int i;
+ int err = 0;
+
+ spin_lock_init(&bus->mdio_lock);
+
+ if (NULL == bus || NULL == bus->name ||
+ NULL == bus->read ||
+ NULL == bus->write)
+ return -EINVAL;
+
+ if (bus->reset)
+ bus->reset(bus);
+
+ for (i = 0; i < PHY_MAX_ADDR; i++) {
+ struct phy_device *phydev;
+
+ phydev = get_phy_device(bus, i);
+
+ if (IS_ERR(phydev))
+ return PTR_ERR(phydev);
+
+ /* There's a PHY at this address
+ * We need to set:
+ * 1) IRQ
+ * 2) bus_id
+ * 3) parent
+ * 4) bus
+ * 5) mii_bus
+ * And, we need to register it */
+ if (phydev) {
+ phydev->irq = bus->irq[i];
+
+ phydev->dev.parent = bus->dev;
+ phydev->dev.bus = &mdio_bus_type;
+ sprintf(phydev->dev.bus_id, "phy%d:%d", bus->id, i);
+
+ phydev->bus = bus;
+
+ err = device_register(&phydev->dev);
+
+ if (err)
+ printk(KERN_ERR "phy %d failed to register\n",
+ i);
+ }
+
+ bus->phy_map[i] = phydev;
+ }
+
+ pr_info("%s: probed\n", bus->name);
+
+ return err;
+}
+EXPORT_SYMBOL(mdiobus_register);
+
+void mdiobus_unregister(struct mii_bus *bus)
+{
+ int i;
+
+ for (i = 0; i < PHY_MAX_ADDR; i++) {
+ if (bus->phy_map[i]) {
+ device_unregister(&bus->phy_map[i]->dev);
+ kfree(bus->phy_map[i]);
+ }
+ }
+}
+EXPORT_SYMBOL(mdiobus_unregister);
+
+/* mdio_bus_match
+ *
+ * description: Given a PHY device, and a PHY driver, return 1 if
+ * the driver supports the device. Otherwise, return 0
+ */
+static int mdio_bus_match(struct device *dev, struct device_driver *drv)
+{
+ struct phy_device *phydev = to_phy_device(dev);
+ struct phy_driver *phydrv = to_phy_driver(drv);
+
+ return (phydrv->phy_id == (phydev->phy_id & phydrv->phy_id_mask));
+}
+
+/* Suspend and resume. Copied from platform_suspend and
+ * platform_resume
+ */
+static int mdio_bus_suspend(struct device * dev, u32 state)
+{
+ int ret = 0;
+ struct device_driver *drv = dev->driver;
+
+ if (drv && drv->suspend) {
+ ret = drv->suspend(dev, state, SUSPEND_DISABLE);
+ if (ret == 0)
+ ret = drv->suspend(dev, state, SUSPEND_SAVE_STATE);
+ if (ret == 0)
+ ret = drv->suspend(dev, state, SUSPEND_POWER_DOWN);
+ }
+ return ret;
+}
+
+static int mdio_bus_resume(struct device * dev)
+{
+ int ret = 0;
+ struct device_driver *drv = dev->driver;
+
+ if (drv && drv->resume) {
+ ret = drv->resume(dev, RESUME_POWER_ON);
+ if (ret == 0)
+ ret = drv->resume(dev, RESUME_RESTORE_STATE);
+ if (ret == 0)
+ ret = drv->resume(dev, RESUME_ENABLE);
+ }
+ return ret;
+}
+
+struct bus_type mdio_bus_type = {
+ .name = "mdio_bus",
+ .match = mdio_bus_match,
+ .suspend = mdio_bus_suspend,
+ .resume = mdio_bus_resume,
+};
+
+int __init mdio_bus_init(void)
+{
+ return bus_register(&mdio_bus_type);
+}
+
+void __exit mdio_bus_exit(void)
+{
+ bus_unregister(&mdio_bus_type);
+}
diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
new file mode 100644
index 0000000..d9e11f9
--- /dev/null
+++ b/drivers/net/phy/phy.c
@@ -0,0 +1,871 @@
+/*
+ * drivers/net/phy/phy.c
+ *
+ * Framework for configuring and reading PHY devices
+ * Based on code in sungem_phy.c and gianfar_phy.c
+ *
+ * Author: Andy Fleming
+ *
+ * Copyright (c) 2004 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+#include <linux/config.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/string.h>
+#include <linux/errno.h>
+#include <linux/unistd.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+#include <linux/spinlock.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/version.h>
+#include <linux/mii.h>
+#include <linux/ethtool.h>
+#include <linux/phy.h>
+
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/uaccess.h>
+
+/* Convenience function to print out the current phy status
+ */
+void phy_print_status(struct phy_device *phydev)
+{
+ pr_info("%s: Link is %s", phydev->dev.bus_id,
+ phydev->link ? "Up" : "Down");
+ if (phydev->link)
+ printk(" - %d/%s", phydev->speed,
+ DUPLEX_FULL == phydev->duplex ?
+ "Full" : "Half");
+
+ printk("\n");
+}
+EXPORT_SYMBOL(phy_print_status);
+
+
+/* Convenience functions for reading/writing a given PHY
+ * register. They MUST NOT be called from interrupt context,
+ * because the bus read/write functions may wait for an interrupt
+ * to conclude the operation. */
+int phy_read(struct phy_device *phydev, u16 regnum)
+{
+ int retval;
+ struct mii_bus *bus = phydev->bus;
+
+ spin_lock_bh(&bus->mdio_lock);
+ retval = bus->read(bus, phydev->addr, regnum);
+ spin_unlock_bh(&bus->mdio_lock);
+
+ return retval;
+}
+EXPORT_SYMBOL(phy_read);
+
+int phy_write(struct phy_device *phydev, u16 regnum, u16 val)
+{
+ int err;
+ struct mii_bus *bus = phydev->bus;
+
+ spin_lock_bh(&bus->mdio_lock);
+ err = bus->write(bus, phydev->addr, regnum, val);
+ spin_unlock_bh(&bus->mdio_lock);
+
+ return err;
+}
+EXPORT_SYMBOL(phy_write);
+
+
+int phy_clear_interrupt(struct phy_device *phydev)
+{
+ int err = 0;
+
+ if (phydev->drv->ack_interrupt)
+ err = phydev->drv->ack_interrupt(phydev);
+
+ return err;
+}
+
+
+int phy_config_interrupt(struct phy_device *phydev, u32 interrupts)
+{
+ int err = 0;
+
+ phydev->interrupts = interrupts;
+ if (phydev->drv->config_intr)
+ err = phydev->drv->config_intr(phydev);
+
+ return err;
+}
+
+
+/* phy_aneg_done
+ *
+ * description: Reads the status register and returns 0 either if
+ * auto-negotiation is incomplete, or if there was an error.
+ * Returns BMSR_ANEGCOMPLETE if auto-negotiation is done.
+ */
+static inline int phy_aneg_done(struct phy_device *phydev)
+{
+ int retval;
+
+ retval = phy_read(phydev, MII_BMSR);
+
+ return (retval < 0) ? retval : (retval & BMSR_ANEGCOMPLETE);
+}
+
+/* A structure for mapping a particular speed and duplex
+ * combination to a particular SUPPORTED and ADVERTISED value */
+struct phy_setting {
+ int speed;
+ int duplex;
+ u32 setting;
+};
+
+/* A mapping of all SUPPORTED settings to speed/duplex */
+static struct phy_setting settings[] = {
+ {
+ .speed = 10000,
+ .duplex = DUPLEX_FULL,
+ .setting = SUPPORTED_10000baseT_Full,
+ },
+ {
+ .speed = SPEED_1000,
+ .duplex = DUPLEX_FULL,
+ .setting = SUPPORTED_1000baseT_Full,
+ },
+ {
+ .speed = SPEED_1000,
+ .duplex = DUPLEX_HALF,
+ .setting = SUPPORTED_1000baseT_Half,
+ },
+ {
+ .speed = SPEED_100,
+ .duplex = DUPLEX_FULL,
+ .setting = SUPPORTED_100baseT_Full,
+ },
+ {
+ .speed = SPEED_100,
+ .duplex = DUPLEX_HALF,
+ .setting = SUPPORTED_100baseT_Half,
+ },
+ {
+ .speed = SPEED_10,
+ .duplex = DUPLEX_FULL,
+ .setting = SUPPORTED_10baseT_Full,
+ },
+ {
+ .speed = SPEED_10,
+ .duplex = DUPLEX_HALF,
+ .setting = SUPPORTED_10baseT_Half,
+ },
+};
+
+#define MAX_NUM_SETTINGS (sizeof(settings)/sizeof(struct phy_setting))
+
+/* phy_find_setting
+ *
+ * description: Searches the settings array for the setting which
+ * matches the desired speed and duplex, and returns the index
+ * of that setting. Returns the index of the last setting if
+ * none of the others match.
+ */
+static inline int phy_find_setting(int speed, int duplex)
+{
+ int idx = 0;
+
+ while (idx < ARRAY_SIZE(settings) &&
+ (settings[idx].speed != speed ||
+ settings[idx].duplex != duplex))
+ idx++;
+
+ return idx < MAX_NUM_SETTINGS ? idx : MAX_NUM_SETTINGS - 1;
+}
+
+/* phy_find_valid
+ * idx: The first index in settings[] to search
+ * features: A mask of the valid settings
+ *
+ * description: Returns the index of the first valid setting less
+ * than or equal to the one pointed to by idx, as determined by
+ * the mask in features. Returns the index of the last setting
+ * if nothing else matches.
+ */
+static inline int phy_find_valid(int idx, u32 features)
+{
+ while (idx < MAX_NUM_SETTINGS && !(settings[idx].setting & features))
+ idx++;
+
+ return idx < MAX_NUM_SETTINGS ? idx : MAX_NUM_SETTINGS - 1;
+}
+
+/* phy_sanitize_settings
+ *
+ * description: Make sure the PHY is set to supported speeds and
+ * duplexes. Drop down by one in this order: 1000/FULL,
+ * 1000/HALF, 100/FULL, 100/HALF, 10/FULL, 10/HALF
+ */
+void phy_sanitize_settings(struct phy_device *phydev)
+{
+ u32 features = phydev->supported;
+ int idx;
+
+ /* Sanitize settings based on PHY capabilities */
+ if ((features & SUPPORTED_Autoneg) == 0)
+ phydev->autoneg = 0;
+
+ idx = phy_find_valid(phy_find_setting(phydev->speed, phydev->duplex),
+ features);
+
+ phydev->speed = settings[idx].speed;
+ phydev->duplex = settings[idx].duplex;
+}
+EXPORT_SYMBOL(phy_sanitize_settings);
+
+/* phy_ethtool_sset:
+ * A generic ethtool sset function. Handles all the details
+ *
+ * A few notes about parameter checking:
+ * - We don't set port or transceiver, so we don't care what they
+ * were set to.
+ * - phy_start_aneg() will make sure forced settings are sane, and
+ * choose the next best ones from the ones selected, so we don't
+ * care if ethtool tries to give us bad values
+ *
+ * A note about the PHYCONTROL Layer. If you turn off
+ * CONFIG_PHYCONTROL, you will need to read the PHY status
+ * registers after this function completes, and update your
+ * controller manually.
+ */
+int phy_ethtool_sset(struct phy_device *phydev, struct ethtool_cmd *cmd)
+{
+ if (cmd->phy_address != phydev->addr)
+ return -EINVAL;
+
+ /* We make sure that we don't pass unsupported
+ * values in to the PHY */
+ cmd->advertising &= phydev->supported;
+
+ /* Verify the settings we care about. */
+ if (cmd->autoneg != AUTONEG_ENABLE && cmd->autoneg != AUTONEG_DISABLE)
+ return -EINVAL;
+
+ if (cmd->autoneg == AUTONEG_ENABLE && cmd->advertising == 0)
+ return -EINVAL;
+
+ if (cmd->autoneg == AUTONEG_DISABLE
+ && ((cmd->speed != SPEED_1000
+ && cmd->speed != SPEED_100
+ && cmd->speed != SPEED_10)
+ || (cmd->duplex != DUPLEX_HALF
+ && cmd->duplex != DUPLEX_FULL)))
+ return -EINVAL;
+
+ phydev->autoneg = cmd->autoneg;
+
+ phydev->speed = cmd->speed;
+
+ phydev->advertising = cmd->advertising;
+
+ if (AUTONEG_ENABLE == cmd->autoneg)
+ phydev->advertising |= ADVERTISED_Autoneg;
+ else
+ phydev->advertising &= ~ADVERTISED_Autoneg;
+
+ phydev->duplex = cmd->duplex;
+
+ /* Restart the PHY */
+ phy_start_aneg(phydev);
+
+ return 0;
+}
+
+int phy_ethtool_gset(struct phy_device *phydev, struct ethtool_cmd *cmd)
+{
+ cmd->supported = phydev->supported;
+
+ cmd->advertising = phydev->advertising;
+
+ cmd->speed = phydev->speed;
+ cmd->duplex = phydev->duplex;
+ cmd->port = PORT_MII;
+ cmd->phy_address = phydev->addr;
+ cmd->transceiver = XCVR_EXTERNAL;
+ cmd->autoneg = phydev->autoneg;
+
+ return 0;
+}
+
+
+/* Note that this function is currently incompatible with the
+ * PHYCONTROL layer. It changes registers without regard to
+ * current state. Use at own risk
+ */
+int phy_mii_ioctl(struct phy_device *phydev,
+ struct mii_ioctl_data *mii_data, int cmd)
+{
+ u16 val = mii_data->val_in;
+
+ switch (cmd) {
+ case SIOCGMIIPHY:
+ mii_data->phy_id = phydev->addr;
+ break;
+ case SIOCGMIIREG:
+ mii_data->val_out = phy_read(phydev, mii_data->reg_num);
+ break;
+
+ case SIOCSMIIREG:
+ if (!capable(CAP_NET_ADMIN))
+ return -EPERM;
+
+ if (mii_data->phy_id == phydev->addr) {
+ switch(mii_data->reg_num) {
+ case MII_BMCR:
+ if (val & (BMCR_RESET|BMCR_ANENABLE))
+ phydev->autoneg = AUTONEG_DISABLE;
+ else
+ phydev->autoneg = AUTONEG_ENABLE;
+ if ((!phydev->autoneg) && (val & BMCR_FULLDPLX))
+ phydev->duplex = DUPLEX_FULL;
+ else
+ phydev->duplex = DUPLEX_HALF;
+ break;
+ case MII_ADVERTISE:
+ phydev->advertising = val;
+ break;
+ default:
+ /* do nothing */
+ break;
+ }
+ }
+
+ phy_write(phydev, mii_data->reg_num, val);
+
+ if (mii_data->reg_num == MII_BMCR
+ && val & BMCR_RESET
+ && phydev->drv->config_init)
+ phydev->drv->config_init(phydev);
+ break;
+ }
+
+ return 0;
+}
+
+/* phy_start_aneg
+ *
+ * description: Sanitizes the settings (if we're not
+ * autonegotiating them), and then calls the driver's
+ * config_aneg function. If the PHYCONTROL Layer is operating,
+ * we change the state to reflect the beginning of
+ * Auto-negotiation or forcing.
+ */
+int phy_start_aneg(struct phy_device *phydev)
+{
+ int err;
+
+ spin_lock(&phydev->lock);
+
+ if (AUTONEG_DISABLE == phydev->autoneg)
+ phy_sanitize_settings(phydev);
+
+ err = phydev->drv->config_aneg(phydev);
+
+#ifdef CONFIG_PHYCONTROL
+ if (err < 0)
+ goto out_unlock;
+
+ if (phydev->state != PHY_HALTED) {
+ if (AUTONEG_ENABLE == phydev->autoneg) {
+ phydev->state = PHY_AN;
+ phydev->link_timeout = PHY_AN_TIMEOUT;
+ } else {
+ phydev->state = PHY_FORCING;
+ phydev->link_timeout = PHY_FORCE_TIMEOUT;
+ }
+ }
+
+out_unlock:
+#endif
+ spin_unlock(&phydev->lock);
+ return err;
+}
+EXPORT_SYMBOL(phy_start_aneg);
+
+
+#ifdef CONFIG_PHYCONTROL
+static void phy_change(void *data);
+static void phy_timer(unsigned long data);
+
+/* phy_start_machine:
+ *
+ * description: The PHY infrastructure can run a state machine
+ * which tracks whether the PHY is starting up, negotiating,
+ * etc. This function starts the timer which tracks the state
+ * of the PHY. If you want to be notified when the state
+ * changes, pass in the callback, otherwise, pass NULL. If you
+ * want to maintain your own state machine, do not call this
+ * function. */
+void phy_start_machine(struct phy_device *phydev,
+ void (*handler)(struct net_device *))
+{
+ phydev->adjust_state = handler;
+
+ init_timer(&phydev->phy_timer);
+ phydev->phy_timer.function = &phy_timer;
+ phydev->phy_timer.data = (unsigned long) phydev;
+ mod_timer(&phydev->phy_timer, jiffies + HZ);
+}
+
+/* phy_stop_machine
+ *
+ * description: Stops the state machine timer, sets the state to
+ * UP (unless it wasn't up yet), and then frees the interrupt,
+ * if it is in use. This function must be called BEFORE
+ * phy_detach.
+ */
+void phy_stop_machine(struct phy_device *phydev)
+{
+ del_timer_sync(&phydev->phy_timer);
+
+ spin_lock(&phydev->lock);
+ if (phydev->state > PHY_UP)
+ phydev->state = PHY_UP;
+ spin_unlock(&phydev->lock);
+
+ if (phydev->irq != PHY_POLL)
+ phy_stop_interrupts(phydev);
+
+ phydev->adjust_state = NULL;
+}
+
+/* phy_force_reduction
+ *
+ * description: Reduces the speed/duplex settings by
+ * one notch. The order is so:
+ * 1000/FULL, 1000/HALF, 100/FULL, 100/HALF,
+ * 10/FULL, 10/HALF. The function bottoms out at 10/HALF.
+ */
+static void phy_force_reduction(struct phy_device *phydev)
+{
+ int idx;
+
+ idx = phy_find_setting(phydev->speed, phydev->duplex);
+
+ idx++;
+
+ idx = phy_find_valid(idx, phydev->supported);
+
+ phydev->speed = settings[idx].speed;
+ phydev->duplex = settings[idx].duplex;
+
+ pr_info("Trying %d/%s\n", phydev->speed,
+ DUPLEX_FULL == phydev->duplex ?
+ "FULL" : "HALF");
+}
+
+
+/* phy_error:
+ *
+ * Moves the PHY to the HALTED state in response to a read
+ * or write error, and tells the controller the link is down.
+ * Must not be called from interrupt context, or while the
+ * phydev->lock is held.
+ */
+void phy_error(struct phy_device *phydev)
+{
+ spin_lock(&phydev->lock);
+ phydev->state = PHY_HALTED;
+ spin_unlock(&phydev->lock);
+}
+
+/* phy_interrupt
+ *
+ * description: When a PHY interrupt occurs, the handler disables
+ * interrupts, and schedules a work task to clear the interrupt.
+ */
+static irqreturn_t phy_interrupt(int irq, void *phy_dat, struct pt_regs *regs)
+{
+ struct phy_device *phydev = phy_dat;
+
+ /* The MDIO bus is not allowed to be written in interrupt
+ * context, so we need to disable the irq here. A work
+ * queue will write the PHY to disable and clear the
+ * interrupt, and then reenable the irq line. */
+ disable_irq_nosync(irq);
+
+ schedule_work(&phydev->phy_queue);
+
+ return IRQ_HANDLED;
+}
+
+/* Enable the interrupts from the PHY side */
+int phy_enable_interrupts(struct phy_device *phydev)
+{
+ int err;
+
+ err = phy_clear_interrupt(phydev);
+
+ if (err < 0)
+ return err;
+
+ err = phy_config_interrupt(phydev, PHY_INTERRUPT_ENABLED);
+
+ return err;
+}
+EXPORT_SYMBOL(phy_enable_interrupts);
+
+/* Disable the PHY interrupts from the PHY side */
+int phy_disable_interrupts(struct phy_device *phydev)
+{
+ int err;
+
+ /* Disable PHY interrupts */
+ err = phy_config_interrupt(phydev, PHY_INTERRUPT_DISABLED);
+
+ if (err)
+ goto phy_err;
+
+ /* Clear the interrupt */
+ err = phy_clear_interrupt(phydev);
+
+ if (err)
+ goto phy_err;
+
+ return 0;
+
+phy_err:
+ phy_error(phydev);
+
+ return err;
+}
+EXPORT_SYMBOL(phy_disable_interrupts);
+
+/* phy_start_interrupts
+ *
+ * description: Request the interrupt for the given PHY. If
+ * this fails, then we set irq to PHY_POLL.
+ * Otherwise, we enable the interrupts in the PHY.
+ * Returns 0 on success.
+ * This should only be called with a valid IRQ number.
+ */
+int phy_start_interrupts(struct phy_device *phydev)
+{
+ int err = 0;
+
+ INIT_WORK(&phydev->phy_queue, phy_change, phydev);
+
+ if (request_irq(phydev->irq, phy_interrupt,
+ SA_SHIRQ,
+ "phy_interrupt",
+ phydev) < 0) {
+ printk(KERN_WARNING "%s: Can't get IRQ %d (PHY)\n",
+ phydev->bus->name,
+ phydev->irq);
+ phydev->irq = PHY_POLL;
+ return 0;
+ }
+
+ err = phy_enable_interrupts(phydev);
+
+ return err;
+}
+EXPORT_SYMBOL(phy_start_interrupts);
+
+int phy_stop_interrupts(struct phy_device *phydev)
+{
+ int err;
+
+ err = phy_disable_interrupts(phydev);
+
+ if (err)
+ phy_error(phydev);
+
+ free_irq(phydev->irq, phydev);
+
+ return err;
+}
+EXPORT_SYMBOL(phy_stop_interrupts);
+
+
+/* Scheduled by the phy_interrupt/timer to handle PHY changes */
+static void phy_change(void *data)
+{
+ int err;
+ struct phy_device *phydev = data;
+
+ err = phy_disable_interrupts(phydev);
+
+ if (err)
+ goto phy_err;
+
+ spin_lock(&phydev->lock);
+ if ((PHY_RUNNING == phydev->state) || (PHY_NOLINK == phydev->state))
+ phydev->state = PHY_CHANGELINK;
+ spin_unlock(&phydev->lock);
+
+ enable_irq(phydev->irq);
+
+ /* Reenable interrupts */
+ err = phy_config_interrupt(phydev, PHY_INTERRUPT_ENABLED);
+
+ if (err)
+ goto irq_enable_err;
+
+ return;
+
+irq_enable_err:
+ disable_irq(phydev->irq);
+phy_err:
+ phy_error(phydev);
+}
+
+/* Bring down the PHY link, and stop checking the status. */
+void phy_stop(struct phy_device *phydev)
+{
+ spin_lock(&phydev->lock);
+
+ if (PHY_HALTED == phydev->state)
+ goto out_unlock;
+
+ if (phydev->irq != PHY_POLL) {
+ /* Clear any pending interrupts */
+ phy_clear_interrupt(phydev);
+
+ /* Disable PHY Interrupts */
+ phy_config_interrupt(phydev, PHY_INTERRUPT_DISABLED);
+ }
+
+ phydev->state = PHY_HALTED;
+
+out_unlock:
+ spin_unlock(&phydev->lock);
+}
+
+
+/* phy_start
+ *
+ * description: Indicates the attached device's readiness to
+ * handle PHY-related work. Used during startup to start the
+ * PHY, and after a call to phy_stop() to resume operation.
+ * Also used to indicate the MDIO bus has cleared an error
+ * condition.
+ */
+void phy_start(struct phy_device *phydev)
+{
+ spin_lock(&phydev->lock);
+
+ switch (phydev->state) {
+ case PHY_STARTING:
+ phydev->state = PHY_PENDING;
+ break;
+ case PHY_READY:
+ phydev->state = PHY_UP;
+ break;
+ case PHY_HALTED:
+ phydev->state = PHY_RESUMING;
+ default:
+ break;
+ }
+ spin_unlock(&phydev->lock);
+}
+EXPORT_SYMBOL(phy_stop);
+EXPORT_SYMBOL(phy_start);
+
+/* PHY timer which handles the state machine */
+static void phy_timer(unsigned long data)
+{
+ struct phy_device *phydev = (struct phy_device *)data;
+ int needs_aneg = 0;
+ int err = 0;
+
+ spin_lock(&phydev->lock);
+
+ if (phydev->adjust_state)
+ phydev->adjust_state(phydev->attached_dev);
+
+ switch(phydev->state) {
+ case PHY_DOWN:
+ case PHY_STARTING:
+ case PHY_READY:
+ case PHY_PENDING:
+ break;
+ case PHY_UP:
+ needs_aneg = 1;
+
+ phydev->link_timeout = PHY_AN_TIMEOUT;
+
+ break;
+ case PHY_AN:
+ /* Check if negotiation is done. Break
+ * if there's an error */
+ err = phy_aneg_done(phydev);
+ if (err < 0)
+ break;
+
+ /* If auto-negotiation is done, we change to
+ * either RUNNING, or NOLINK */
+ if (err > 0) {
+ err = phy_read_status(phydev);
+
+ if (err)
+ break;
+
+ if (phydev->link) {
+ phydev->state = PHY_RUNNING;
+ netif_carrier_on(phydev->attached_dev);
+ } else {
+ phydev->state = PHY_NOLINK;
+ netif_carrier_off(phydev->attached_dev);
+ }
+
+ phydev->adjust_link(phydev->attached_dev);
+
+ } else if (0 == phydev->link_timeout--) {
+ /* The counter expired, so either we
+ * switch to forced mode, or the
+ * magic_aneg bit exists, and we try aneg
+ * again */
+ if (!(phydev->drv->flags & PHY_HAS_MAGICANEG)) {
+ int idx;
+
+ /* We'll start from the
+ * fastest speed, and work
+ * our way down */
+ idx = phy_find_valid(0,
+ phydev->supported);
+
+ phydev->speed = settings[idx].speed;
+ phydev->duplex = settings[idx].duplex;
+
+ phydev->autoneg = AUTONEG_DISABLE;
+ phydev->state = PHY_FORCING;
+ phydev->link_timeout =
+ PHY_FORCE_TIMEOUT;
+
+ pr_info("Trying %d/%s\n",
+ phydev->speed,
+ DUPLEX_FULL ==
+ phydev->duplex ?
+ "FULL" : "HALF");
+ }
+
+ needs_aneg = 1;
+ }
+ break;
+ case PHY_NOLINK:
+ err = phy_read_status(phydev);
+
+ if (err)
+ break;
+
+ if (phydev->link) {
+ phydev->state = PHY_RUNNING;
+ netif_carrier_on(phydev->attached_dev);
+ phydev->adjust_link(phydev->attached_dev);
+ }
+ break;
+ case PHY_FORCING:
+ err = phy_read_status(phydev);
+
+ if (err)
+ break;
+
+ if (phydev->link) {
+ phydev->state = PHY_RUNNING;
+ netif_carrier_on(phydev->attached_dev);
+ } else {
+ if (0 == phydev->link_timeout--) {
+ phy_force_reduction(phydev);
+ needs_aneg = 1;
+ }
+ }
+
+ phydev->adjust_link(phydev->attached_dev);
+ break;
+ case PHY_RUNNING:
+ /* Only register a CHANGE if we are
+ * polling */
+ if (PHY_POLL == phydev->irq)
+ phydev->state = PHY_CHANGELINK;
+ break;
+ case PHY_CHANGELINK:
+ err = phy_read_status(phydev);
+
+ if (err)
+ break;
+
+ if (phydev->link) {
+ phydev->state = PHY_RUNNING;
+ netif_carrier_on(phydev->attached_dev);
+ } else {
+ phydev->state = PHY_NOLINK;
+ netif_carrier_off(phydev->attached_dev);
+ }
+
+ phydev->adjust_link(phydev->attached_dev);
+
+ if (PHY_POLL != phydev->irq)
+ err = phy_config_interrupt(phydev,
+ PHY_INTERRUPT_ENABLED);
+ break;
+ case PHY_HALTED:
+ if (phydev->link) {
+ phydev->link = 0;
+ netif_carrier_off(phydev->attached_dev);
+ phydev->adjust_link(phydev->attached_dev);
+ }
+ break;
+ case PHY_RESUMING:
+
+ err = phy_clear_interrupt(phydev);
+
+ if (err)
+ break;
+
+ err = phy_config_interrupt(phydev,
+ PHY_INTERRUPT_ENABLED);
+
+ if (err)
+ break;
+
+ if (AUTONEG_ENABLE == phydev->autoneg) {
+ err = phy_aneg_done(phydev);
+ if (err < 0)
+ break;
+
+ /* err > 0 if AN is done.
+ * Otherwise, it's 0, and we're
+ * still waiting for AN */
+ if (err > 0) {
+ phydev->state = PHY_RUNNING;
+ } else {
+ phydev->state = PHY_AN;
+ phydev->link_timeout = PHY_AN_TIMEOUT;
+ }
+ } else
+ phydev->state = PHY_RUNNING;
+ break;
+ }
+
+ spin_unlock(&phydev->lock);
+
+ if (needs_aneg)
+ err = phy_start_aneg(phydev);
+
+ if (err < 0)
+ phy_error(phydev);
+
+ mod_timer(&phydev->phy_timer, jiffies + PHY_STATE_TIME * HZ);
+}
+
+#endif /* CONFIG_PHYCONTROL */
diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
new file mode 100644
index 0000000..33f7bdb
--- /dev/null
+++ b/drivers/net/phy/phy_device.c
@@ -0,0 +1,696 @@
+/*
+ * drivers/net/phy/phy_device.c
+ *
+ * Framework for finding and configuring PHYs.
+ * Also contains generic PHY driver
+ *
+ * Author: Andy Fleming
+ *
+ * Copyright (c) 2004 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+#include <linux/config.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/string.h>
+#include <linux/errno.h>
+#include <linux/unistd.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+#include <linux/spinlock.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/version.h>
+#include <linux/mii.h>
+#include <linux/ethtool.h>
+#include <linux/phy.h>
+
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/uaccess.h>
+
+static struct phy_driver genphy_driver;
+extern int mdio_bus_init(void);
+extern void mdio_bus_exit(void);
+
+/* get_phy_device
+ *
+ * description: Reads the ID registers of the PHY at addr on the
+ * bus, then allocates and returns the phy_device to
+ * represent it.
+ */
+struct phy_device * get_phy_device(struct mii_bus *bus, int addr)
+{
+ int phy_reg;
+ u32 phy_id;
+ struct phy_device *dev = NULL;
+
+ /* Grab the bits from PHYIR1, and put them
+ * in the upper half */
+ phy_reg = bus->read(bus, addr, MII_PHYSID1);
+
+ if (phy_reg < 0)
+ return ERR_PTR(phy_reg);
+
+ phy_id = (phy_reg & 0xffff) << 16;
+
+ /* Grab the bits from PHYIR2, and put them in the lower half */
+ phy_reg = bus->read(bus, addr, MII_PHYSID2);
+
+ if (phy_reg < 0)
+ return ERR_PTR(phy_reg);
+
+ phy_id |= (phy_reg & 0xffff);
+
+ /* If the phy_id is all Fs, there is no device there */
+ if (0xffffffff == phy_id)
+ return NULL;
+
+ /* Otherwise, we allocate the device, and initialize the
+ * default values */
+ dev = kcalloc(1, sizeof(*dev), GFP_KERNEL);
+
+ if (NULL == dev)
+ return ERR_PTR(-ENOMEM);
+
+ dev->speed = 0;
+ dev->duplex = -1;
+ dev->pause = dev->asym_pause = 0;
+ dev->link = 1;
+
+ dev->autoneg = AUTONEG_ENABLE;
+
+ dev->addr = addr;
+ dev->phy_id = phy_id;
+ dev->bus = bus;
+
+ dev->state = PHY_DOWN;
+
+ spin_lock_init(&dev->lock);
+
+ return dev;
+}
+
+#ifdef CONFIG_PHYCONTROL
+/* phy_prepare_link:
+ *
+ * description: Tells the PHY infrastructure to handle the
+ * gory details on monitoring link status (whether through
+ * polling or an interrupt), and to call back to the
+ * connected device driver when the link status changes.
+ * If you want to monitor your own link state, don't call
+ * this function */
+void phy_prepare_link(struct phy_device *phydev,
+ void (*handler)(struct net_device *))
+{
+ phydev->adjust_link = handler;
+}
+
+/* phy_connect:
+ *
+ * description: Convenience function for connecting ethernet
+ * devices to PHY devices. The default behavior is for
+ * the PHY infrastructure to handle everything, and only notify
+ * the connected driver when the link status changes. If you
+ * don't want, or can't use the provided functionality, you may
+ * choose to call only the subset of functions which provide
+ * the desired functionality.
+ */
+struct phy_device * phy_connect(struct net_device *dev, const char *phy_id,
+ void (*handler)(struct net_device *), u32 flags)
+{
+ struct phy_device *phydev;
+
+ phydev = phy_attach(dev, phy_id, flags);
+
+ if (IS_ERR(phydev))
+ return phydev;
+
+ phy_prepare_link(phydev, handler);
+
+ phy_start_machine(phydev, NULL);
+
+ if (phydev->irq > 0)
+ phy_start_interrupts(phydev);
+
+ return phydev;
+}
+EXPORT_SYMBOL(phy_connect);
+
+void phy_disconnect(struct phy_device *phydev)
+{
+ if (phydev->irq > 0)
+ phy_stop_interrupts(phydev);
+
+ phy_stop_machine(phydev);
+
+ phydev->adjust_link = NULL;
+
+ phy_detach(phydev);
+}
+EXPORT_SYMBOL(phy_disconnect);
+
+#endif /* CONFIG_PHYCONTROL */
+
+/* phy_attach:
+ *
+ * description: Called by drivers to attach to a particular PHY
+ * device. The phy_device is found, and properly hooked up
+ * to the phy_driver. If no driver is attached, then the
+ * genphy_driver is used. The phy_device is given a ptr to
+ * the attaching device, and given a callback for link status
+ * change. The phy_device is returned to the attaching
+ * driver.
+ */
+static int phy_compare_id(struct device *dev, void *data)
+{
+ return strcmp((char *)data, dev->bus_id) ? 0 : 1;
+}
+
+struct phy_device *phy_attach(struct net_device *dev,
+ const char *phy_id, u32 flags)
+{
+ struct bus_type *bus = &mdio_bus_type;
+ struct phy_device *phydev;
+ struct device *d;
+
+ /* Search the list of PHY devices on the mdio bus for the
+ * PHY with the requested name */
+ d = bus_find_device(bus, NULL, (void *)phy_id, phy_compare_id);
+
+ if (d) {
+ phydev = to_phy_device(d);
+ } else {
+ printk(KERN_ERR "%s not found\n", phy_id);
+ return ERR_PTR(-ENODEV);
+ }
+
+ /* Assume that if there is no driver, that it doesn't
+ * exist, and we should use the genphy driver. */
+ if (NULL == d->driver) {
+ int err;
+ down_write(&d->bus->subsys.rwsem);
+ d->driver = &genphy_driver.driver;
+
+ err = d->driver->probe(d);
+
+ if (err < 0)
+ return ERR_PTR(err);
+
+ device_bind_driver(d);
+ up_write(&d->bus->subsys.rwsem);
+ }
+
+ if (phydev->attached_dev) {
+ printk(KERN_ERR "%s: %s already attached\n",
+ dev->name, phy_id);
+ return ERR_PTR(-EBUSY);
+ }
+
+ phydev->attached_dev = dev;
+
+ phydev->dev_flags = flags;
+
+ return phydev;
+}
+EXPORT_SYMBOL(phy_attach);
+
+void phy_detach(struct phy_device *phydev)
+{
+ phydev->attached_dev = NULL;
+
+ /* If the device had no specific driver before (i.e. - it
+ * was using the generic driver), we unbind the device
+ * from the generic driver so that there's a chance a
+ * real driver could be loaded */
+ if (phydev->dev.driver == &genphy_driver.driver) {
+ down_write(&phydev->dev.bus->subsys.rwsem);
+ device_release_driver(&phydev->dev);
+ up_write(&phydev->dev.bus->subsys.rwsem);
+ }
+}
+EXPORT_SYMBOL(phy_detach);
+
+
+/* Generic PHY support and helper functions */
+
+/* genphy_config_advert
+ *
+ * description: Writes MII_ADVERTISE with the appropriate values,
+ * after sanitizing the values to make sure we only advertise
+ * what is supported
+ */
+int genphy_config_advert(struct phy_device *phydev)
+{
+ u32 advertise;
+ int adv;
+ int err;
+
+ /* Only allow advertising what
+ * this PHY supports */
+ phydev->advertising &= phydev->supported;
+ advertise = phydev->advertising;
+
+ /* Setup standard advertisement */
+ adv = phy_read(phydev, MII_ADVERTISE);
+
+ if (adv < 0)
+ return adv;
+
+ adv &= ~(ADVERTISE_ALL | ADVERTISE_100BASE4 | ADVERTISE_PAUSE_CAP |
+ ADVERTISE_PAUSE_ASYM);
+ if (advertise & ADVERTISED_10baseT_Half)
+ adv |= ADVERTISE_10HALF;
+ if (advertise & ADVERTISED_10baseT_Full)
+ adv |= ADVERTISE_10FULL;
+ if (advertise & ADVERTISED_100baseT_Half)
+ adv |= ADVERTISE_100HALF;
+ if (advertise & ADVERTISED_100baseT_Full)
+ adv |= ADVERTISE_100FULL;
+ if (advertise & ADVERTISED_Pause)
+ adv |= ADVERTISE_PAUSE_CAP;
+ if (advertise & ADVERTISED_Asym_Pause)
+ adv |= ADVERTISE_PAUSE_ASYM;
+
+ err = phy_write(phydev, MII_ADVERTISE, adv);
+
+ if (err < 0)
+ return err;
+
+ /* Configure gigabit if it's supported */
+ if (phydev->supported & (SUPPORTED_1000baseT_Half |
+ SUPPORTED_1000baseT_Full)) {
+ adv = phy_read(phydev, MII_CTRL1000);
+
+ if (adv < 0)
+ return adv;
+
+ adv &= ~(ADVERTISE_1000FULL | ADVERTISE_1000HALF);
+ if (advertise & SUPPORTED_1000baseT_Half)
+ adv |= ADVERTISE_1000HALF;
+ if (advertise & SUPPORTED_1000baseT_Full)
+ adv |= ADVERTISE_1000FULL;
+ err = phy_write(phydev, MII_CTRL1000, adv);
+
+ if (err < 0)
+ return err;
+ }
+
+ return adv;
+}
+EXPORT_SYMBOL(genphy_config_advert);
+
+/* genphy_setup_forced
+ *
+ * description: Configures MII_BMCR to force speed/duplex
+ * to the values in phydev. Assumes that the values are valid.
+ * Please see phy_sanitize_settings() */
+int genphy_setup_forced(struct phy_device *phydev)
+{
+ int ctl = BMCR_RESET;
+
+ phydev->pause = phydev->asym_pause = 0;
+
+ if (SPEED_1000 == phydev->speed)
+ ctl |= BMCR_SPEED1000;
+ else if (SPEED_100 == phydev->speed)
+ ctl |= BMCR_SPEED100;
+
+ if (DUPLEX_FULL == phydev->duplex)
+ ctl |= BMCR_FULLDPLX;
+
+ ctl = phy_write(phydev, MII_BMCR, ctl);
+
+ if (ctl < 0)
+ return ctl;
+
+ /* We just reset the device, so we'd better configure any
+ * settings the PHY requires to operate */
+ if (phydev->drv->config_init)
+ ctl = phydev->drv->config_init(phydev);
+
+ return ctl;
+}
+
+
+/* Enable and Restart Autonegotiation */
+int genphy_restart_aneg(struct phy_device *phydev)
+{
+ int ctl;
+
+ ctl = phy_read(phydev, MII_BMCR);
+
+ if (ctl < 0)
+ return ctl;
+
+ ctl |= (BMCR_ANENABLE | BMCR_ANRESTART);
+
+ /* Don't isolate the PHY if we're negotiating */
+ ctl &= ~(BMCR_ISOLATE);
+
+ ctl = phy_write(phydev, MII_BMCR, ctl);
+
+ return ctl;
+}
+
+
+/* genphy_config_aneg
+ *
+ * description: If auto-negotiation is enabled, we configure the
+ * advertising, and then restart auto-negotiation. If it is not
+ * enabled, then we write the BMCR
+ */
+int genphy_config_aneg(struct phy_device *phydev)
+{
+ int err = 0;
+
+ if (AUTONEG_ENABLE == phydev->autoneg) {
+ err = genphy_config_advert(phydev);
+
+ if (err < 0)
+ return err;
+
+ err = genphy_restart_aneg(phydev);
+ } else
+ err = genphy_setup_forced(phydev);
+
+ return err;
+}
+EXPORT_SYMBOL(genphy_config_aneg);
+
+/* genphy_update_link
+ *
+ * description: Update the value in phydev->link to reflect the
+ * current link value. In order to do this, we need to read
+ * the status register twice, keeping the second value
+ */
+int genphy_update_link(struct phy_device *phydev)
+{
+ int status;
+
+ /* Do a fake read */
+ status = phy_read(phydev, MII_BMSR);
+
+ if (status < 0)
+ return status;
+
+ /* Read link and autonegotiation status */
+ status = phy_read(phydev, MII_BMSR);
+
+ if (status < 0)
+ return status;
+
+ if ((status & BMSR_LSTATUS) == 0)
+ phydev->link = 0;
+ else
+ phydev->link = 1;
+
+ return 0;
+}
+
+/* genphy_read_status
+ *
+ * description: Check the link, then figure out the current state
+ * by comparing what we advertise with what the link partner
+ * advertises. Start by checking the gigabit possibilities,
+ * then move on to 10/100.
+ */
+int genphy_read_status(struct phy_device *phydev)
+{
+ int adv;
+ int err;
+ int lpa;
+ int lpagb = 0;
+
+ /* Update the link, but return if there
+ * was an error */
+ err = genphy_update_link(phydev);
+ if (err)
+ return err;
+
+ if (AUTONEG_ENABLE == phydev->autoneg) {
+ if (phydev->supported & (SUPPORTED_1000baseT_Half
+ | SUPPORTED_1000baseT_Full)) {
+ lpagb = phy_read(phydev, MII_STAT1000);
+
+ if (lpagb < 0)
+ return lpagb;
+
+ adv = phy_read(phydev, MII_CTRL1000);
+
+ if (adv < 0)
+ return adv;
+
+ lpagb &= adv << 2;
+ }
+
+ lpa = phy_read(phydev, MII_LPA);
+
+ if (lpa < 0)
+ return lpa;
+
+ adv = phy_read(phydev, MII_ADVERTISE);
+
+ if (adv < 0)
+ return adv;
+
+ lpa &= adv;
+
+ phydev->speed = SPEED_10;
+ phydev->duplex = DUPLEX_HALF;
+ phydev->pause = phydev->asym_pause = 0;
+
+ if (lpagb & (LPA_1000FULL | LPA_1000HALF)) {
+ phydev->speed = SPEED_1000;
+
+ if (lpagb & LPA_1000FULL)
+ phydev->duplex = DUPLEX_FULL;
+ } else if (lpa & (LPA_100FULL | LPA_100HALF)) {
+ phydev->speed = SPEED_100;
+
+ if (lpa & LPA_100FULL)
+ phydev->duplex = DUPLEX_FULL;
+ } else
+ if (lpa & LPA_10FULL)
+ phydev->duplex = DUPLEX_FULL;
+
+ if (phydev->duplex == DUPLEX_FULL){
+ phydev->pause = lpa & LPA_PAUSE_CAP ? 1 : 0;
+ phydev->asym_pause = lpa & LPA_PAUSE_ASYM ? 1 : 0;
+ }
+ } else {
+ int bmcr = phy_read(phydev, MII_BMCR);
+ if (bmcr < 0)
+ return bmcr;
+
+ if (bmcr & BMCR_FULLDPLX)
+ phydev->duplex = DUPLEX_FULL;
+ else
+ phydev->duplex = DUPLEX_HALF;
+
+ if (bmcr & BMCR_SPEED1000)
+ phydev->speed = SPEED_1000;
+ else if (bmcr & BMCR_SPEED100)
+ phydev->speed = SPEED_100;
+ else
+ phydev->speed = SPEED_10;
+
+ phydev->pause = phydev->asym_pause = 0;
+ }
+
+ return 0;
+}
+EXPORT_SYMBOL(genphy_read_status);
+
+static int genphy_config_init(struct phy_device *phydev)
+{
+ u32 val;
+ u32 features;
+
+ /* For now, I'll claim that the generic driver supports
+ * all possible port types */
+ features = (SUPPORTED_TP | SUPPORTED_MII
+ | SUPPORTED_AUI | SUPPORTED_FIBRE |
+ SUPPORTED_BNC);
+
+ /* Do we support autonegotiation? */
+ val = phy_read(phydev, MII_BMSR);
+
+ if (val < 0)
+ return val;
+
+ if (val & BMSR_ANEGCAPABLE)
+ features |= SUPPORTED_Autoneg;
+
+ if (val & BMSR_100FULL)
+ features |= SUPPORTED_100baseT_Full;
+ if (val & BMSR_100HALF)
+ features |= SUPPORTED_100baseT_Half;
+ if (val & BMSR_10FULL)
+ features |= SUPPORTED_10baseT_Full;
+ if (val & BMSR_10HALF)
+ features |= SUPPORTED_10baseT_Half;
+
+ if (val & BMSR_ESTATEN) {
+ val = phy_read(phydev, MII_ESTATUS);
+
+ if (val < 0)
+ return val;
+
+ if (val & ESTATUS_1000_TFULL)
+ features |= SUPPORTED_1000baseT_Full;
+ if (val & ESTATUS_1000_THALF)
+ features |= SUPPORTED_1000baseT_Half;
+ }
+
+ phydev->supported = features;
+ phydev->advertising = features;
+
+ return 0;
+}
+
+
+/* phy_probe
+ *
+ * description: Take care of setting up the phy_device structure,
+ * set the state to READY (the driver's init function should
+ * set it to STARTING if needed).
+ */
+static int phy_probe(struct device *dev)
+{
+ struct phy_device *phydev;
+ struct phy_driver *phydrv;
+ struct device_driver *drv;
+ int err = 0;
+
+ phydev = to_phy_device(dev);
+
+ /* Make sure the driver is held.
+ * XXX -- Is this correct? */
+ drv = get_driver(phydev->dev.driver);
+ phydrv = to_phy_driver(drv);
+ phydev->drv = phydrv;
+
+ /* Disable the interrupt if the PHY doesn't support it */
+ if (!(phydrv->flags & PHY_HAS_INTERRUPT))
+ phydev->irq = PHY_POLL;
+
+ spin_lock(&phydev->lock);
+
+ /* Start out supporting everything. Eventually,
+ * a controller will attach, and may modify one
+ * or both of these values */
+ phydev->supported = phydrv->features;
+ phydev->advertising = phydrv->features;
+
+ /* Set the state to READY by default */
+ phydev->state = PHY_READY;
+
+ if (phydev->drv->probe)
+ err = phydev->drv->probe(phydev);
+
+ spin_unlock(&phydev->lock);
+
+ if (err < 0)
+ return err;
+
+ if (phydev->drv->config_init)
+ err = phydev->drv->config_init(phydev);
+
+ return err;
+}
+
+static int phy_remove(struct device *dev)
+{
+ struct phy_device *phydev;
+
+ phydev = to_phy_device(dev);
+
+ spin_lock(&phydev->lock);
+ phydev->state = PHY_DOWN;
+ spin_unlock(&phydev->lock);
+
+ if (phydev->drv->remove)
+ phydev->drv->remove(phydev);
+
+ put_driver(dev->driver);
+ phydev->drv = NULL;
+
+ return 0;
+}
+
+int phy_driver_register(struct phy_driver *new_driver)
+{
+ int retval;
+
+ memset(&new_driver->driver, 0, sizeof(new_driver->driver));
+ new_driver->driver.name = new_driver->name;
+ new_driver->driver.bus = &mdio_bus_type;
+ new_driver->driver.probe = phy_probe;
+ new_driver->driver.remove = phy_remove;
+
+ retval = driver_register(&new_driver->driver);
+
+ if (retval) {
+ printk(KERN_ERR "%s: Error %d in registering driver\n",
+ new_driver->name, retval);
+
+ return retval;
+ }
+
+ pr_info("%s: Registered new driver\n", new_driver->name);
+
+ return 0;
+}
+EXPORT_SYMBOL(phy_driver_register);
+
+void phy_driver_unregister(struct phy_driver *drv)
+{
+ driver_unregister(&drv->driver);
+}
+EXPORT_SYMBOL(phy_driver_unregister);
+
+static struct phy_driver genphy_driver = {
+ .phy_id = 0xffffffff,
+ .phy_id_mask = 0xffffffff,
+ .name = "Generic PHY",
+ .config_init = genphy_config_init,
+ .features = 0,
+ .config_aneg = genphy_config_aneg,
+ .read_status = genphy_read_status,
+ .driver = {.owner= THIS_MODULE, },
+};
+
+static int __init phy_init(void)
+{
+ int rc;
+
+ rc = mdio_bus_init();
+ if (rc)
+ return rc;
+
+ rc = phy_driver_register(&genphy_driver);
+ if (rc)
+ mdio_bus_exit();
+
+ return rc;
+}
+
+static void __exit phy_exit(void)
+{
+ phy_driver_unregister(&genphy_driver);
+ mdio_bus_exit();
+}
+
+subsys_initcall(phy_init);
+module_exit(phy_exit);
diff --git a/drivers/net/phy/qsemi.c b/drivers/net/phy/qsemi.c
new file mode 100644
index 0000000..d461ba4
--- /dev/null
+++ b/drivers/net/phy/qsemi.c
@@ -0,0 +1,143 @@
+/*
+ * drivers/net/phy/qsemi.c
+ *
+ * Driver for Quality Semiconductor PHYs
+ *
+ * Author: Andy Fleming
+ *
+ * Copyright (c) 2004 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+#include <linux/config.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/string.h>
+#include <linux/errno.h>
+#include <linux/unistd.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+#include <linux/spinlock.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/version.h>
+#include <linux/mii.h>
+#include <linux/ethtool.h>
+#include <linux/phy.h>
+
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/uaccess.h>
+
+/* ------------------------------------------------------------------------- */
+/* The Quality Semiconductor QS6612 is used on the RPX CLLF */
+
+/* register definitions */
+
+#define MII_QS6612_MCR 17 /* Mode Control Register */
+#define MII_QS6612_FTR 27 /* Factory Test Register */
+#define MII_QS6612_MCO 28 /* Misc. Control Register */
+#define MII_QS6612_ISR 29 /* Interrupt Source Register */
+#define MII_QS6612_IMR 30 /* Interrupt Mask Register */
+#define MII_QS6612_IMR_INIT 0x003a
+#define MII_QS6612_PCR 31 /* 100BaseTx PHY Control Reg. */
+
+#define QS6612_PCR_AN_COMPLETE 0x1000
+#define QS6612_PCR_RLBEN 0x0200
+#define QS6612_PCR_DCREN 0x0100
+#define QS6612_PCR_4B5BEN 0x0040
+#define QS6612_PCR_TX_ISOLATE 0x0020
+#define QS6612_PCR_MLT3_DIS 0x0002
+#define QS6612_PCR_SCRM_DESCRM 0x0001
+
+MODULE_DESCRIPTION("Quality Semiconductor PHY driver");
+MODULE_AUTHOR("Andy Fleming");
+MODULE_LICENSE("GPL");
+
+/* Returns 0, unless there's a write error */
+static int qs6612_config_init(struct phy_device *phydev)
+{
+ /* The PHY powers up isolated on the RPX,
+ * so send a command to allow operation.
+ * XXX - My docs indicate this should be 0x0940
+ * ...or something. The current value sets three
+ * reserved bits, bit 11, which specifies it should be
+ * set to one, bit 10, which specifies it should be set
+ * to 0, and bit 7, which doesn't specify. However, my
+ * docs are preliminary, and I will leave it like this
+ * until someone more knowledgable corrects me or it.
+ * -- Andy Fleming
+ */
+ return phy_write(phydev, MII_QS6612_PCR, 0x0dc0);
+}
+
+static int qs6612_ack_interrupt(struct phy_device *phydev)
+{
+ int err;
+
+ err = phy_read(phydev, MII_QS6612_ISR);
+
+ if (err < 0)
+ return err;
+
+ err = phy_read(phydev, MII_BMSR);
+
+ if (err < 0)
+ return err;
+
+ err = phy_read(phydev, MII_EXPANSION);
+
+ if (err < 0)
+ return err;
+
+ return 0;
+}
+
+static int qs6612_config_intr(struct phy_device *phydev)
+{
+ int err;
+ if (phydev->interrupts == PHY_INTERRUPT_ENABLED)
+ err = phy_write(phydev, MII_QS6612_IMR,
+ MII_QS6612_IMR_INIT);
+ else
+ err = phy_write(phydev, MII_QS6612_IMR, 0);
+
+ return err;
+
+}
+
+static struct phy_driver qs6612_driver = {
+ .phy_id = 0x00181440,
+ .name = "QS6612",
+ .phy_id_mask = 0xfffffff0,
+ .features = PHY_BASIC_FEATURES,
+ .flags = PHY_HAS_INTERRUPT,
+ .config_init = qs6612_config_init,
+ .config_aneg = genphy_config_aneg,
+ .read_status = genphy_read_status,
+ .ack_interrupt = qs6612_ack_interrupt,
+ .config_intr = qs6612_config_intr,
+ .driver = { .owner = THIS_MODULE,},
+};
+
+static int __init qs6612_init(void)
+{
+ return phy_driver_register(&qs6612_driver);
+}
+
+static void __exit qs6612_exit(void)
+{
+ phy_driver_unregister(&qs6612_driver);
+}
+
+module_init(qs6612_init);
+module_exit(qs6612_exit);
diff --git a/drivers/net/r8169.c b/drivers/net/r8169.c
index d5afe05..f0471d1 100644
--- a/drivers/net/r8169.c
+++ b/drivers/net/r8169.c
@@ -187,6 +187,7 @@
{ PCI_DEVICE(PCI_VENDOR_ID_REALTEK, 0x8169), },
{ PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4300), },
{ PCI_DEVICE(0x16ec, 0x0116), },
+ { PCI_VENDOR_ID_LINKSYS, 0x1032, PCI_ANY_ID, 0x0024, },
{0,},
};
diff --git a/drivers/net/s2io-regs.h b/drivers/net/s2io-regs.h
index 7092ca6..2234a8f 100644
--- a/drivers/net/s2io-regs.h
+++ b/drivers/net/s2io-regs.h
@@ -62,6 +62,7 @@
#define ADAPTER_STATUS_RMAC_REMOTE_FAULT BIT(6)
#define ADAPTER_STATUS_RMAC_LOCAL_FAULT BIT(7)
#define ADAPTER_STATUS_RMAC_PCC_IDLE vBIT(0xFF,8,8)
+#define ADAPTER_STATUS_RMAC_PCC_FOUR_IDLE vBIT(0x0F,8,8)
#define ADAPTER_STATUS_RC_PRC_QUIESCENT vBIT(0xFF,16,8)
#define ADAPTER_STATUS_MC_DRAM_READY BIT(24)
#define ADAPTER_STATUS_MC_QUEUES_READY BIT(25)
@@ -77,21 +78,34 @@
#define ADAPTER_ECC_EN BIT(55)
u64 serr_source;
-#define SERR_SOURCE_PIC BIT(0)
-#define SERR_SOURCE_TXDMA BIT(1)
-#define SERR_SOURCE_RXDMA BIT(2)
+#define SERR_SOURCE_PIC BIT(0)
+#define SERR_SOURCE_TXDMA BIT(1)
+#define SERR_SOURCE_RXDMA BIT(2)
#define SERR_SOURCE_MAC BIT(3)
#define SERR_SOURCE_MC BIT(4)
#define SERR_SOURCE_XGXS BIT(5)
-#define SERR_SOURCE_ANY (SERR_SOURCE_PIC | \
- SERR_SOURCE_TXDMA | \
- SERR_SOURCE_RXDMA | \
- SERR_SOURCE_MAC | \
- SERR_SOURCE_MC | \
- SERR_SOURCE_XGXS)
+#define SERR_SOURCE_ANY (SERR_SOURCE_PIC | \
+ SERR_SOURCE_TXDMA | \
+ SERR_SOURCE_RXDMA | \
+ SERR_SOURCE_MAC | \
+ SERR_SOURCE_MC | \
+ SERR_SOURCE_XGXS)
+ u64 pci_mode;
+#define GET_PCI_MODE(val) ((val & vBIT(0xF, 0, 4)) >> 60)
+#define PCI_MODE_PCI_33 0
+#define PCI_MODE_PCI_66 0x1
+#define PCI_MODE_PCIX_M1_66 0x2
+#define PCI_MODE_PCIX_M1_100 0x3
+#define PCI_MODE_PCIX_M1_133 0x4
+#define PCI_MODE_PCIX_M2_66 0x5
+#define PCI_MODE_PCIX_M2_100 0x6
+#define PCI_MODE_PCIX_M2_133 0x7
+#define PCI_MODE_UNSUPPORTED BIT(0)
+#define PCI_MODE_32_BITS BIT(8)
+#define PCI_MODE_UNKNOWN_MODE BIT(9)
- u8 unused_0[0x800 - 0x120];
+ u8 unused_0[0x800 - 0x128];
/* PCI-X Controller registers */
u64 pic_int_status;
@@ -153,7 +167,11 @@
u8 unused4[0x08];
u64 gpio_int_reg;
+#define GPIO_INT_REG_LINK_DOWN BIT(1)
+#define GPIO_INT_REG_LINK_UP BIT(2)
u64 gpio_int_mask;
+#define GPIO_INT_MASK_LINK_DOWN BIT(1)
+#define GPIO_INT_MASK_LINK_UP BIT(2)
u64 gpio_alarms;
u8 unused5[0x38];
@@ -223,19 +241,16 @@
u64 xmsi_data;
u64 rx_mat;
+#define RX_MAT_SET(ring, msi) vBIT(msi, (8 * ring), 8)
u8 unused6[0x8];
- u64 tx_mat0_7;
- u64 tx_mat8_15;
- u64 tx_mat16_23;
- u64 tx_mat24_31;
- u64 tx_mat32_39;
- u64 tx_mat40_47;
- u64 tx_mat48_55;
- u64 tx_mat56_63;
+ u64 tx_mat0_n[0x8];
+#define TX_MAT_SET(fifo, msi) vBIT(msi, (8 * fifo), 8)
- u8 unused_1[0x10];
+ u8 unused_1[0x8];
+ u64 stat_byte_cnt;
+#define STAT_BC(n) vBIT(n,4,12)
/* Automated statistics collection */
u64 stat_cfg;
@@ -246,6 +261,7 @@
#define STAT_TRSF_PER(n) TBD
#define PER_SEC 0x208d5
#define SET_UPDT_PERIOD(n) vBIT((PER_SEC*n),32,32)
+#define SET_UPDT_CLICKS(val) vBIT(val, 32, 32)
u64 stat_addr;
@@ -267,8 +283,15 @@
u64 gpio_control;
#define GPIO_CTRL_GPIO_0 BIT(8)
+ u64 misc_control;
+#define MISC_LINK_STABILITY_PRD(val) vBIT(val,29,3)
- u8 unused7[0x600];
+ u8 unused7_1[0x240 - 0x208];
+
+ u64 wreq_split_mask;
+#define WREQ_SPLIT_MASK_SET_MASK(val) vBIT(val, 52, 12)
+
+ u8 unused7_2[0x800 - 0x248];
/* TxDMA registers */
u64 txdma_int_status;
@@ -290,6 +313,7 @@
u64 pcc_err_reg;
#define PCC_FB_ECC_DB_ERR vBIT(0xFF, 16, 8)
+#define PCC_ENABLE_FOUR vBIT(0x0F,0,8)
u64 pcc_err_mask;
u64 pcc_err_alarm;
@@ -468,6 +492,7 @@
#define PRC_CTRL_NO_SNOOP (BIT(22)|BIT(23))
#define PRC_CTRL_NO_SNOOP_DESC BIT(22)
#define PRC_CTRL_NO_SNOOP_BUFF BIT(23)
+#define PRC_CTRL_BIMODAL_INTERRUPT BIT(37)
#define PRC_CTRL_RXD_BACKOFF_INTERVAL(val) vBIT(val,40,24)
u64 prc_alarm_action;
@@ -691,6 +716,10 @@
#define MC_ERR_REG_MIRI_CRI_ERR_0 BIT(22)
#define MC_ERR_REG_MIRI_CRI_ERR_1 BIT(23)
#define MC_ERR_REG_SM_ERR BIT(31)
+#define MC_ERR_REG_ECC_ALL_SNG (BIT(6) | \
+ BIT(7) | BIT(17) | BIT(19))
+#define MC_ERR_REG_ECC_ALL_DBL (BIT(14) | \
+ BIT(15) | BIT(18) | BIT(20))
u64 mc_err_mask;
u64 mc_err_alarm;
@@ -736,7 +765,19 @@
u64 mc_rldram_test_d1;
u8 unused24[0x300 - 0x288];
u64 mc_rldram_test_d2;
- u8 unused25[0x700 - 0x308];
+
+ u8 unused24_1[0x360 - 0x308];
+ u64 mc_rldram_ctrl;
+#define MC_RLDRAM_ENABLE_ODT BIT(7)
+
+ u8 unused24_2[0x640 - 0x368];
+ u64 mc_rldram_ref_per_herc;
+#define MC_RLDRAM_SET_REF_PERIOD(val) vBIT(val, 0, 16)
+
+ u8 unused24_3[0x660 - 0x648];
+ u64 mc_rldram_mrs_herc;
+
+ u8 unused25[0x700 - 0x668];
u64 mc_debug_ctrl;
u8 unused26[0x3000 - 0x2f08];
diff --git a/drivers/net/s2io.c b/drivers/net/s2io.c
index ea638b1..7ca7822 100644
--- a/drivers/net/s2io.c
+++ b/drivers/net/s2io.c
@@ -11,29 +11,28 @@
* See the file COPYING in this distribution for more information.
*
* Credits:
- * Jeff Garzik : For pointing out the improper error condition
- * check in the s2io_xmit routine and also some
- * issues in the Tx watch dog function. Also for
- * patiently answering all those innumerable
+ * Jeff Garzik : For pointing out the improper error condition
+ * check in the s2io_xmit routine and also some
+ * issues in the Tx watch dog function. Also for
+ * patiently answering all those innumerable
* questions regaring the 2.6 porting issues.
* Stephen Hemminger : Providing proper 2.6 porting mechanism for some
* macros available only in 2.6 Kernel.
- * Francois Romieu : For pointing out all code part that were
+ * Francois Romieu : For pointing out all code part that were
* deprecated and also styling related comments.
- * Grant Grundler : For helping me get rid of some Architecture
+ * Grant Grundler : For helping me get rid of some Architecture
* dependent code.
* Christopher Hellwig : Some more 2.6 specific issues in the driver.
- *
+ *
* The module loadable parameters that are supported by the driver and a brief
* explaination of all the variables.
- * rx_ring_num : This can be used to program the number of receive rings used
- * in the driver.
- * rx_ring_len: This defines the number of descriptors each ring can have. This
+ * rx_ring_num : This can be used to program the number of receive rings used
+ * in the driver.
+ * rx_ring_len: This defines the number of descriptors each ring can have. This
* is also an array of size 8.
* tx_fifo_num: This defines the number of Tx FIFOs thats used int the driver.
- * tx_fifo_len: This too is an array of 8. Each element defines the number of
+ * tx_fifo_len: This too is an array of 8. Each element defines the number of
* Tx descriptors that can be associated with each corresponding FIFO.
- * in PCI Configuration space.
************************************************************************/
#include <linux/config.h>
@@ -56,27 +55,39 @@
#include <linux/ethtool.h>
#include <linux/version.h>
#include <linux/workqueue.h>
+#include <linux/if_vlan.h>
-#include <asm/io.h>
#include <asm/system.h>
#include <asm/uaccess.h>
+#include <asm/io.h>
/* local include */
#include "s2io.h"
#include "s2io-regs.h"
/* S2io Driver name & version. */
-static char s2io_driver_name[] = "s2io";
-static char s2io_driver_version[] = "Version 1.7.7.1";
+static char s2io_driver_name[] = "Neterion";
+static char s2io_driver_version[] = "Version 2.0.3.1";
-/*
+static inline int RXD_IS_UP2DT(RxD_t *rxdp)
+{
+ int ret;
+
+ ret = ((!(rxdp->Control_1 & RXD_OWN_XENA)) &&
+ (GET_RXD_MARKER(rxdp->Control_2) != THE_RXD_MARK));
+
+ return ret;
+}
+
+/*
* Cards with following subsystem_id have a link state indication
* problem, 600B, 600C, 600D, 640B, 640C and 640D.
* macro below identifies these cards given the subsystem_id.
*/
-#define CARDS_WITH_FAULTY_LINK_INDICATORS(subid) \
- (((subid >= 0x600B) && (subid <= 0x600D)) || \
- ((subid >= 0x640B) && (subid <= 0x640D))) ? 1 : 0
+#define CARDS_WITH_FAULTY_LINK_INDICATORS(dev_type, subid) \
+ (dev_type == XFRAME_I_DEVICE) ? \
+ ((((subid >= 0x600B) && (subid <= 0x600D)) || \
+ ((subid >= 0x640B) && (subid <= 0x640D))) ? 1 : 0) : 0
#define LINK_IS_UP(val64) (!(val64 & (ADAPTER_STATUS_RMAC_REMOTE_FAULT | \
ADAPTER_STATUS_RMAC_LOCAL_FAULT)))
@@ -86,9 +97,12 @@
static inline int rx_buffer_level(nic_t * sp, int rxb_size, int ring)
{
int level = 0;
- if ((sp->pkt_cnt[ring] - rxb_size) > 16) {
+ mac_info_t *mac_control;
+
+ mac_control = &sp->mac_control;
+ if ((mac_control->rings[ring].pkt_cnt - rxb_size) > 16) {
level = LOW;
- if ((sp->pkt_cnt[ring] - rxb_size) < MAX_RXDS_PER_BLOCK) {
+ if (rxb_size <= MAX_RXDS_PER_BLOCK) {
level = PANIC;
}
}
@@ -145,6 +159,9 @@
{"rmac_pause_cnt"},
{"rmac_accepted_ip"},
{"rmac_err_tcp"},
+ {"\n DRIVER STATISTICS"},
+ {"single_bit_ecc_errs"},
+ {"double_bit_ecc_errs"},
};
#define S2IO_STAT_LEN sizeof(ethtool_stats_keys)/ ETH_GSTRING_LEN
@@ -153,8 +170,37 @@
#define S2IO_TEST_LEN sizeof(s2io_gstrings) / ETH_GSTRING_LEN
#define S2IO_STRINGS_LEN S2IO_TEST_LEN * ETH_GSTRING_LEN
+#define S2IO_TIMER_CONF(timer, handle, arg, exp) \
+ init_timer(&timer); \
+ timer.function = handle; \
+ timer.data = (unsigned long) arg; \
+ mod_timer(&timer, (jiffies + exp)) \
-/*
+/* Add the vlan */
+static void s2io_vlan_rx_register(struct net_device *dev,
+ struct vlan_group *grp)
+{
+ nic_t *nic = dev->priv;
+ unsigned long flags;
+
+ spin_lock_irqsave(&nic->tx_lock, flags);
+ nic->vlgrp = grp;
+ spin_unlock_irqrestore(&nic->tx_lock, flags);
+}
+
+/* Unregister the vlan */
+static void s2io_vlan_rx_kill_vid(struct net_device *dev, unsigned long vid)
+{
+ nic_t *nic = dev->priv;
+ unsigned long flags;
+
+ spin_lock_irqsave(&nic->tx_lock, flags);
+ if (nic->vlgrp)
+ nic->vlgrp->vlan_devices[vid] = NULL;
+ spin_unlock_irqrestore(&nic->tx_lock, flags);
+}
+
+/*
* Constants to be programmed into the Xena's registers, to configure
* the XAUI.
*/
@@ -162,7 +208,28 @@
#define SWITCH_SIGN 0xA5A5A5A5A5A5A5A5ULL
#define END_SIGN 0x0
-static u64 default_mdio_cfg[] = {
+static u64 herc_act_dtx_cfg[] = {
+ /* Set address */
+ 0x8000051536750000ULL, 0x80000515367500E0ULL,
+ /* Write data */
+ 0x8000051536750004ULL, 0x80000515367500E4ULL,
+ /* Set address */
+ 0x80010515003F0000ULL, 0x80010515003F00E0ULL,
+ /* Write data */
+ 0x80010515003F0004ULL, 0x80010515003F00E4ULL,
+ /* Set address */
+ 0x801205150D440000ULL, 0x801205150D4400E0ULL,
+ /* Write data */
+ 0x801205150D440004ULL, 0x801205150D4400E4ULL,
+ /* Set address */
+ 0x80020515F2100000ULL, 0x80020515F21000E0ULL,
+ /* Write data */
+ 0x80020515F2100004ULL, 0x80020515F21000E4ULL,
+ /* Done */
+ END_SIGN
+};
+
+static u64 xena_mdio_cfg[] = {
/* Reset PMA PLL */
0xC001010000000000ULL, 0xC0010100000000E0ULL,
0xC0010100008000E4ULL,
@@ -172,7 +239,7 @@
END_SIGN
};
-static u64 default_dtx_cfg[] = {
+static u64 xena_dtx_cfg[] = {
0x8000051500000000ULL, 0x80000515000000E0ULL,
0x80000515D93500E4ULL, 0x8001051500000000ULL,
0x80010515000000E0ULL, 0x80010515001E00E4ULL,
@@ -196,8 +263,7 @@
END_SIGN
};
-
-/*
+/*
* Constants for Fixing the MacAddress problem seen mostly on
* Alpha machines.
*/
@@ -226,20 +292,25 @@
static unsigned int rx_ring_num = 1;
static unsigned int rx_ring_sz[MAX_RX_RINGS] =
{[0 ...(MAX_RX_RINGS - 1)] = 0 };
-static unsigned int Stats_refresh_time = 4;
+static unsigned int rts_frm_len[MAX_RX_RINGS] =
+ {[0 ...(MAX_RX_RINGS - 1)] = 0 };
+static unsigned int use_continuous_tx_intrs = 1;
static unsigned int rmac_pause_time = 65535;
static unsigned int mc_pause_threshold_q0q3 = 187;
static unsigned int mc_pause_threshold_q4q7 = 187;
static unsigned int shared_splits;
static unsigned int tmac_util_period = 5;
static unsigned int rmac_util_period = 5;
+static unsigned int bimodal = 0;
#ifndef CONFIG_S2IO_NAPI
static unsigned int indicate_max_pkts;
#endif
+/* Frequency of Rx desc syncs expressed as power of 2 */
+static unsigned int rxsync_frequency = 3;
-/*
+/*
* S2IO device table.
- * This table lists all the devices that this driver supports.
+ * This table lists all the devices that this driver supports.
*/
static struct pci_device_id s2io_tbl[] __devinitdata = {
{PCI_VENDOR_ID_S2IO, PCI_DEVICE_ID_S2IO_WIN,
@@ -247,9 +318,9 @@
{PCI_VENDOR_ID_S2IO, PCI_DEVICE_ID_S2IO_UNI,
PCI_ANY_ID, PCI_ANY_ID},
{PCI_VENDOR_ID_S2IO, PCI_DEVICE_ID_HERC_WIN,
- PCI_ANY_ID, PCI_ANY_ID},
- {PCI_VENDOR_ID_S2IO, PCI_DEVICE_ID_HERC_UNI,
- PCI_ANY_ID, PCI_ANY_ID},
+ PCI_ANY_ID, PCI_ANY_ID},
+ {PCI_VENDOR_ID_S2IO, PCI_DEVICE_ID_HERC_UNI,
+ PCI_ANY_ID, PCI_ANY_ID},
{0,}
};
@@ -268,8 +339,8 @@
/**
* init_shared_mem - Allocation and Initialization of Memory
* @nic: Device private variable.
- * Description: The function allocates all the memory areas shared
- * between the NIC and the driver. This includes Tx descriptors,
+ * Description: The function allocates all the memory areas shared
+ * between the NIC and the driver. This includes Tx descriptors,
* Rx descriptors and the statistics block.
*/
@@ -279,11 +350,11 @@
void *tmp_v_addr, *tmp_v_addr_next;
dma_addr_t tmp_p_addr, tmp_p_addr_next;
RxD_block_t *pre_rxd_blk = NULL;
- int i, j, blk_cnt;
+ int i, j, blk_cnt, rx_sz, tx_sz;
int lst_size, lst_per_page;
struct net_device *dev = nic->dev;
#ifdef CONFIG_2BUFF_MODE
- unsigned long tmp;
+ u64 tmp;
buffAdd_t *ba;
#endif
@@ -300,36 +371,41 @@
size += config->tx_cfg[i].fifo_len;
}
if (size > MAX_AVAILABLE_TXDS) {
- DBG_PRINT(ERR_DBG, "%s: Total number of Tx FIFOs ",
- dev->name);
- DBG_PRINT(ERR_DBG, "exceeds the maximum value ");
- DBG_PRINT(ERR_DBG, "that can be used\n");
+ DBG_PRINT(ERR_DBG, "%s: Requested TxDs too high, ",
+ __FUNCTION__);
+ DBG_PRINT(ERR_DBG, "Requested: %d, max supported: 8192\n", size);
return FAILURE;
}
lst_size = (sizeof(TxD_t) * config->max_txds);
+ tx_sz = lst_size * size;
lst_per_page = PAGE_SIZE / lst_size;
for (i = 0; i < config->tx_fifo_num; i++) {
int fifo_len = config->tx_cfg[i].fifo_len;
int list_holder_size = fifo_len * sizeof(list_info_hold_t);
- nic->list_info[i] = kmalloc(list_holder_size, GFP_KERNEL);
- if (!nic->list_info[i]) {
+ mac_control->fifos[i].list_info = kmalloc(list_holder_size,
+ GFP_KERNEL);
+ if (!mac_control->fifos[i].list_info) {
DBG_PRINT(ERR_DBG,
"Malloc failed for list_info\n");
return -ENOMEM;
}
- memset(nic->list_info[i], 0, list_holder_size);
+ memset(mac_control->fifos[i].list_info, 0, list_holder_size);
}
for (i = 0; i < config->tx_fifo_num; i++) {
int page_num = TXD_MEM_PAGE_CNT(config->tx_cfg[i].fifo_len,
lst_per_page);
- mac_control->tx_curr_put_info[i].offset = 0;
- mac_control->tx_curr_put_info[i].fifo_len =
+ mac_control->fifos[i].tx_curr_put_info.offset = 0;
+ mac_control->fifos[i].tx_curr_put_info.fifo_len =
config->tx_cfg[i].fifo_len - 1;
- mac_control->tx_curr_get_info[i].offset = 0;
- mac_control->tx_curr_get_info[i].fifo_len =
+ mac_control->fifos[i].tx_curr_get_info.offset = 0;
+ mac_control->fifos[i].tx_curr_get_info.fifo_len =
config->tx_cfg[i].fifo_len - 1;
+ mac_control->fifos[i].fifo_no = i;
+ mac_control->fifos[i].nic = nic;
+ mac_control->fifos[i].max_txds = MAX_SKB_FRAGS;
+
for (j = 0; j < page_num; j++) {
int k = 0;
dma_addr_t tmp_p;
@@ -345,16 +421,15 @@
while (k < lst_per_page) {
int l = (j * lst_per_page) + k;
if (l == config->tx_cfg[i].fifo_len)
- goto end_txd_alloc;
- nic->list_info[i][l].list_virt_addr =
+ break;
+ mac_control->fifos[i].list_info[l].list_virt_addr =
tmp_v + (k * lst_size);
- nic->list_info[i][l].list_phy_addr =
+ mac_control->fifos[i].list_info[l].list_phy_addr =
tmp_p + (k * lst_size);
k++;
}
}
}
- end_txd_alloc:
/* Allocation and initialization of RXDs in Rings */
size = 0;
@@ -367,21 +442,26 @@
return FAILURE;
}
size += config->rx_cfg[i].num_rxd;
- nic->block_count[i] =
+ mac_control->rings[i].block_count =
config->rx_cfg[i].num_rxd / (MAX_RXDS_PER_BLOCK + 1);
- nic->pkt_cnt[i] =
- config->rx_cfg[i].num_rxd - nic->block_count[i];
+ mac_control->rings[i].pkt_cnt =
+ config->rx_cfg[i].num_rxd - mac_control->rings[i].block_count;
}
+ size = (size * (sizeof(RxD_t)));
+ rx_sz = size;
for (i = 0; i < config->rx_ring_num; i++) {
- mac_control->rx_curr_get_info[i].block_index = 0;
- mac_control->rx_curr_get_info[i].offset = 0;
- mac_control->rx_curr_get_info[i].ring_len =
+ mac_control->rings[i].rx_curr_get_info.block_index = 0;
+ mac_control->rings[i].rx_curr_get_info.offset = 0;
+ mac_control->rings[i].rx_curr_get_info.ring_len =
config->rx_cfg[i].num_rxd - 1;
- mac_control->rx_curr_put_info[i].block_index = 0;
- mac_control->rx_curr_put_info[i].offset = 0;
- mac_control->rx_curr_put_info[i].ring_len =
+ mac_control->rings[i].rx_curr_put_info.block_index = 0;
+ mac_control->rings[i].rx_curr_put_info.offset = 0;
+ mac_control->rings[i].rx_curr_put_info.ring_len =
config->rx_cfg[i].num_rxd - 1;
+ mac_control->rings[i].nic = nic;
+ mac_control->rings[i].ring_no = i;
+
blk_cnt =
config->rx_cfg[i].num_rxd / (MAX_RXDS_PER_BLOCK + 1);
/* Allocating all the Rx blocks */
@@ -395,32 +475,36 @@
&tmp_p_addr);
if (tmp_v_addr == NULL) {
/*
- * In case of failure, free_shared_mem()
- * is called, which should free any
- * memory that was alloced till the
+ * In case of failure, free_shared_mem()
+ * is called, which should free any
+ * memory that was alloced till the
* failure happened.
*/
- nic->rx_blocks[i][j].block_virt_addr =
+ mac_control->rings[i].rx_blocks[j].block_virt_addr =
tmp_v_addr;
return -ENOMEM;
}
memset(tmp_v_addr, 0, size);
- nic->rx_blocks[i][j].block_virt_addr = tmp_v_addr;
- nic->rx_blocks[i][j].block_dma_addr = tmp_p_addr;
+ mac_control->rings[i].rx_blocks[j].block_virt_addr =
+ tmp_v_addr;
+ mac_control->rings[i].rx_blocks[j].block_dma_addr =
+ tmp_p_addr;
}
/* Interlinking all Rx Blocks */
for (j = 0; j < blk_cnt; j++) {
- tmp_v_addr = nic->rx_blocks[i][j].block_virt_addr;
+ tmp_v_addr =
+ mac_control->rings[i].rx_blocks[j].block_virt_addr;
tmp_v_addr_next =
- nic->rx_blocks[i][(j + 1) %
+ mac_control->rings[i].rx_blocks[(j + 1) %
blk_cnt].block_virt_addr;
- tmp_p_addr = nic->rx_blocks[i][j].block_dma_addr;
+ tmp_p_addr =
+ mac_control->rings[i].rx_blocks[j].block_dma_addr;
tmp_p_addr_next =
- nic->rx_blocks[i][(j + 1) %
+ mac_control->rings[i].rx_blocks[(j + 1) %
blk_cnt].block_dma_addr;
pre_rxd_blk = (RxD_block_t *) tmp_v_addr;
- pre_rxd_blk->reserved_1 = END_OF_BLOCK; /* last RxD
+ pre_rxd_blk->reserved_1 = END_OF_BLOCK; /* last RxD
* marker.
*/
#ifndef CONFIG_2BUFF_MODE
@@ -433,43 +517,43 @@
}
#ifdef CONFIG_2BUFF_MODE
- /*
+ /*
* Allocation of Storages for buffer addresses in 2BUFF mode
* and the buffers as well.
*/
for (i = 0; i < config->rx_ring_num; i++) {
blk_cnt =
config->rx_cfg[i].num_rxd / (MAX_RXDS_PER_BLOCK + 1);
- nic->ba[i] = kmalloc((sizeof(buffAdd_t *) * blk_cnt),
+ mac_control->rings[i].ba = kmalloc((sizeof(buffAdd_t *) * blk_cnt),
GFP_KERNEL);
- if (!nic->ba[i])
+ if (!mac_control->rings[i].ba)
return -ENOMEM;
for (j = 0; j < blk_cnt; j++) {
int k = 0;
- nic->ba[i][j] = kmalloc((sizeof(buffAdd_t) *
+ mac_control->rings[i].ba[j] = kmalloc((sizeof(buffAdd_t) *
(MAX_RXDS_PER_BLOCK + 1)),
GFP_KERNEL);
- if (!nic->ba[i][j])
+ if (!mac_control->rings[i].ba[j])
return -ENOMEM;
while (k != MAX_RXDS_PER_BLOCK) {
- ba = &nic->ba[i][j][k];
+ ba = &mac_control->rings[i].ba[j][k];
- ba->ba_0_org = kmalloc
+ ba->ba_0_org = (void *) kmalloc
(BUF0_LEN + ALIGN_SIZE, GFP_KERNEL);
if (!ba->ba_0_org)
return -ENOMEM;
- tmp = (unsigned long) ba->ba_0_org;
+ tmp = (u64) ba->ba_0_org;
tmp += ALIGN_SIZE;
- tmp &= ~((unsigned long) ALIGN_SIZE);
+ tmp &= ~((u64) ALIGN_SIZE);
ba->ba_0 = (void *) tmp;
- ba->ba_1_org = kmalloc
+ ba->ba_1_org = (void *) kmalloc
(BUF1_LEN + ALIGN_SIZE, GFP_KERNEL);
if (!ba->ba_1_org)
return -ENOMEM;
- tmp = (unsigned long) ba->ba_1_org;
+ tmp = (u64) ba->ba_1_org;
tmp += ALIGN_SIZE;
- tmp &= ~((unsigned long) ALIGN_SIZE);
+ tmp &= ~((u64) ALIGN_SIZE);
ba->ba_1 = (void *) tmp;
k++;
}
@@ -483,9 +567,9 @@
(nic->pdev, size, &mac_control->stats_mem_phy);
if (!mac_control->stats_mem) {
- /*
- * In case of failure, free_shared_mem() is called, which
- * should free any memory that was alloced till the
+ /*
+ * In case of failure, free_shared_mem() is called, which
+ * should free any memory that was alloced till the
* failure happened.
*/
return -ENOMEM;
@@ -495,15 +579,14 @@
tmp_v_addr = mac_control->stats_mem;
mac_control->stats_info = (StatInfo_t *) tmp_v_addr;
memset(tmp_v_addr, 0, size);
-
DBG_PRINT(INIT_DBG, "%s:Ring Mem PHY: 0x%llx\n", dev->name,
(unsigned long long) tmp_p_addr);
return SUCCESS;
}
-/**
- * free_shared_mem - Free the allocated Memory
+/**
+ * free_shared_mem - Free the allocated Memory
* @nic: Device private variable.
* Description: This function is to free all memory locations allocated by
* the init_shared_mem() function and return it to the kernel.
@@ -533,15 +616,19 @@
lst_per_page);
for (j = 0; j < page_num; j++) {
int mem_blks = (j * lst_per_page);
- if (!nic->list_info[i][mem_blks].list_virt_addr)
+ if ((!mac_control->fifos[i].list_info) ||
+ (!mac_control->fifos[i].list_info[mem_blks].
+ list_virt_addr))
break;
pci_free_consistent(nic->pdev, PAGE_SIZE,
- nic->list_info[i][mem_blks].
+ mac_control->fifos[i].
+ list_info[mem_blks].
list_virt_addr,
- nic->list_info[i][mem_blks].
+ mac_control->fifos[i].
+ list_info[mem_blks].
list_phy_addr);
}
- kfree(nic->list_info[i]);
+ kfree(mac_control->fifos[i].list_info);
}
#ifndef CONFIG_2BUFF_MODE
@@ -550,10 +637,12 @@
size = SIZE_OF_BLOCK;
#endif
for (i = 0; i < config->rx_ring_num; i++) {
- blk_cnt = nic->block_count[i];
+ blk_cnt = mac_control->rings[i].block_count;
for (j = 0; j < blk_cnt; j++) {
- tmp_v_addr = nic->rx_blocks[i][j].block_virt_addr;
- tmp_p_addr = nic->rx_blocks[i][j].block_dma_addr;
+ tmp_v_addr = mac_control->rings[i].rx_blocks[j].
+ block_virt_addr;
+ tmp_p_addr = mac_control->rings[i].rx_blocks[j].
+ block_dma_addr;
if (tmp_v_addr == NULL)
break;
pci_free_consistent(nic->pdev, size,
@@ -566,35 +655,21 @@
for (i = 0; i < config->rx_ring_num; i++) {
blk_cnt =
config->rx_cfg[i].num_rxd / (MAX_RXDS_PER_BLOCK + 1);
- if (!nic->ba[i])
- goto end_free;
for (j = 0; j < blk_cnt; j++) {
int k = 0;
- if (!nic->ba[i][j]) {
- kfree(nic->ba[i]);
- goto end_free;
- }
+ if (!mac_control->rings[i].ba[j])
+ continue;
while (k != MAX_RXDS_PER_BLOCK) {
- buffAdd_t *ba = &nic->ba[i][j][k];
- if (!ba || !ba->ba_0_org || !ba->ba_1_org)
- {
- kfree(nic->ba[i]);
- kfree(nic->ba[i][j]);
- if(ba->ba_0_org)
- kfree(ba->ba_0_org);
- if(ba->ba_1_org)
- kfree(ba->ba_1_org);
- goto end_free;
- }
+ buffAdd_t *ba = &mac_control->rings[i].ba[j][k];
kfree(ba->ba_0_org);
kfree(ba->ba_1_org);
k++;
}
- kfree(nic->ba[i][j]);
+ kfree(mac_control->rings[i].ba[j]);
}
- kfree(nic->ba[i]);
+ if (mac_control->rings[i].ba)
+ kfree(mac_control->rings[i].ba);
}
-end_free:
#endif
if (mac_control->stats_mem) {
@@ -605,12 +680,93 @@
}
}
-/**
- * init_nic - Initialization of hardware
+/**
+ * s2io_verify_pci_mode -
+ */
+
+static int s2io_verify_pci_mode(nic_t *nic)
+{
+ XENA_dev_config_t *bar0 = (XENA_dev_config_t *) nic->bar0;
+ register u64 val64 = 0;
+ int mode;
+
+ val64 = readq(&bar0->pci_mode);
+ mode = (u8)GET_PCI_MODE(val64);
+
+ if ( val64 & PCI_MODE_UNKNOWN_MODE)
+ return -1; /* Unknown PCI mode */
+ return mode;
+}
+
+
+/**
+ * s2io_print_pci_mode -
+ */
+static int s2io_print_pci_mode(nic_t *nic)
+{
+ XENA_dev_config_t *bar0 = (XENA_dev_config_t *) nic->bar0;
+ register u64 val64 = 0;
+ int mode;
+ struct config_param *config = &nic->config;
+
+ val64 = readq(&bar0->pci_mode);
+ mode = (u8)GET_PCI_MODE(val64);
+
+ if ( val64 & PCI_MODE_UNKNOWN_MODE)
+ return -1; /* Unknown PCI mode */
+
+ if (val64 & PCI_MODE_32_BITS) {
+ DBG_PRINT(ERR_DBG, "%s: Device is on 32 bit ", nic->dev->name);
+ } else {
+ DBG_PRINT(ERR_DBG, "%s: Device is on 64 bit ", nic->dev->name);
+ }
+
+ switch(mode) {
+ case PCI_MODE_PCI_33:
+ DBG_PRINT(ERR_DBG, "33MHz PCI bus\n");
+ config->bus_speed = 33;
+ break;
+ case PCI_MODE_PCI_66:
+ DBG_PRINT(ERR_DBG, "66MHz PCI bus\n");
+ config->bus_speed = 133;
+ break;
+ case PCI_MODE_PCIX_M1_66:
+ DBG_PRINT(ERR_DBG, "66MHz PCIX(M1) bus\n");
+ config->bus_speed = 133; /* Herc doubles the clock rate */
+ break;
+ case PCI_MODE_PCIX_M1_100:
+ DBG_PRINT(ERR_DBG, "100MHz PCIX(M1) bus\n");
+ config->bus_speed = 200;
+ break;
+ case PCI_MODE_PCIX_M1_133:
+ DBG_PRINT(ERR_DBG, "133MHz PCIX(M1) bus\n");
+ config->bus_speed = 266;
+ break;
+ case PCI_MODE_PCIX_M2_66:
+ DBG_PRINT(ERR_DBG, "133MHz PCIX(M2) bus\n");
+ config->bus_speed = 133;
+ break;
+ case PCI_MODE_PCIX_M2_100:
+ DBG_PRINT(ERR_DBG, "200MHz PCIX(M2) bus\n");
+ config->bus_speed = 200;
+ break;
+ case PCI_MODE_PCIX_M2_133:
+ DBG_PRINT(ERR_DBG, "266MHz PCIX(M2) bus\n");
+ config->bus_speed = 266;
+ break;
+ default:
+ return -1; /* Unsupported bus speed */
+ }
+
+ return mode;
+}
+
+/**
+ * init_nic - Initialization of hardware
* @nic: device peivate variable
- * Description: The function sequentially configures every block
- * of the H/W from their reset values.
- * Return Value: SUCCESS on success and
+ * Description: The function sequentially configures every block
+ * of the H/W from their reset values.
+ * Return Value: SUCCESS on success and
* '-1' on failure (endian settings incorrect).
*/
@@ -626,21 +782,32 @@
struct config_param *config;
int mdio_cnt = 0, dtx_cnt = 0;
unsigned long long mem_share;
+ int mem_size;
mac_control = &nic->mac_control;
config = &nic->config;
- /* Initialize swapper control register */
- if (s2io_set_swapper(nic)) {
+ /* to set the swapper controle on the card */
+ if(s2io_set_swapper(nic)) {
DBG_PRINT(ERR_DBG,"ERROR: Setting Swapper failed\n");
return -1;
}
+ /*
+ * Herc requires EOI to be removed from reset before XGXS, so..
+ */
+ if (nic->device_type & XFRAME_II_DEVICE) {
+ val64 = 0xA500000000ULL;
+ writeq(val64, &bar0->sw_reset);
+ msleep(500);
+ val64 = readq(&bar0->sw_reset);
+ }
+
/* Remove XGXS from reset state */
val64 = 0;
writeq(val64, &bar0->sw_reset);
- val64 = readq(&bar0->sw_reset);
msleep(500);
+ val64 = readq(&bar0->sw_reset);
/* Enable Receiving broadcasts */
add = &bar0->mac_cfg;
@@ -660,48 +827,58 @@
val64 = dev->mtu;
writeq(vBIT(val64, 2, 14), &bar0->rmac_max_pyld_len);
- /*
- * Configuring the XAUI Interface of Xena.
+ /*
+ * Configuring the XAUI Interface of Xena.
* ***************************************
- * To Configure the Xena's XAUI, one has to write a series
- * of 64 bit values into two registers in a particular
- * sequence. Hence a macro 'SWITCH_SIGN' has been defined
- * which will be defined in the array of configuration values
- * (default_dtx_cfg & default_mdio_cfg) at appropriate places
- * to switch writing from one regsiter to another. We continue
+ * To Configure the Xena's XAUI, one has to write a series
+ * of 64 bit values into two registers in a particular
+ * sequence. Hence a macro 'SWITCH_SIGN' has been defined
+ * which will be defined in the array of configuration values
+ * (xena_dtx_cfg & xena_mdio_cfg) at appropriate places
+ * to switch writing from one regsiter to another. We continue
* writing these values until we encounter the 'END_SIGN' macro.
- * For example, After making a series of 21 writes into
- * dtx_control register the 'SWITCH_SIGN' appears and hence we
+ * For example, After making a series of 21 writes into
+ * dtx_control register the 'SWITCH_SIGN' appears and hence we
* start writing into mdio_control until we encounter END_SIGN.
*/
- while (1) {
- dtx_cfg:
- while (default_dtx_cfg[dtx_cnt] != END_SIGN) {
- if (default_dtx_cfg[dtx_cnt] == SWITCH_SIGN) {
- dtx_cnt++;
- goto mdio_cfg;
- }
- SPECIAL_REG_WRITE(default_dtx_cfg[dtx_cnt],
+ if (nic->device_type & XFRAME_II_DEVICE) {
+ while (herc_act_dtx_cfg[dtx_cnt] != END_SIGN) {
+ SPECIAL_REG_WRITE(herc_act_dtx_cfg[dtx_cnt],
&bar0->dtx_control, UF);
- val64 = readq(&bar0->dtx_control);
+ if (dtx_cnt & 0x1)
+ msleep(1); /* Necessary!! */
dtx_cnt++;
}
- mdio_cfg:
- while (default_mdio_cfg[mdio_cnt] != END_SIGN) {
- if (default_mdio_cfg[mdio_cnt] == SWITCH_SIGN) {
+ } else {
+ while (1) {
+ dtx_cfg:
+ while (xena_dtx_cfg[dtx_cnt] != END_SIGN) {
+ if (xena_dtx_cfg[dtx_cnt] == SWITCH_SIGN) {
+ dtx_cnt++;
+ goto mdio_cfg;
+ }
+ SPECIAL_REG_WRITE(xena_dtx_cfg[dtx_cnt],
+ &bar0->dtx_control, UF);
+ val64 = readq(&bar0->dtx_control);
+ dtx_cnt++;
+ }
+ mdio_cfg:
+ while (xena_mdio_cfg[mdio_cnt] != END_SIGN) {
+ if (xena_mdio_cfg[mdio_cnt] == SWITCH_SIGN) {
+ mdio_cnt++;
+ goto dtx_cfg;
+ }
+ SPECIAL_REG_WRITE(xena_mdio_cfg[mdio_cnt],
+ &bar0->mdio_control, UF);
+ val64 = readq(&bar0->mdio_control);
mdio_cnt++;
+ }
+ if ((xena_dtx_cfg[dtx_cnt] == END_SIGN) &&
+ (xena_mdio_cfg[mdio_cnt] == END_SIGN)) {
+ break;
+ } else {
goto dtx_cfg;
}
- SPECIAL_REG_WRITE(default_mdio_cfg[mdio_cnt],
- &bar0->mdio_control, UF);
- val64 = readq(&bar0->mdio_control);
- mdio_cnt++;
- }
- if ((default_dtx_cfg[dtx_cnt] == END_SIGN) &&
- (default_mdio_cfg[mdio_cnt] == END_SIGN)) {
- break;
- } else {
- goto dtx_cfg;
}
}
@@ -748,12 +925,20 @@
val64 |= BIT(0); /* To enable the FIFO partition. */
writeq(val64, &bar0->tx_fifo_partition_0);
+ /*
+ * Disable 4 PCCs for Xena1, 2 and 3 as per H/W bug
+ * SXE-008 TRANSMIT DMA ARBITRATION ISSUE.
+ */
+ if ((nic->device_type == XFRAME_I_DEVICE) &&
+ (get_xena_rev_id(nic->pdev) < 4))
+ writeq(PCC_ENABLE_FOUR, &bar0->pcc_enable);
+
val64 = readq(&bar0->tx_fifo_partition_0);
DBG_PRINT(INIT_DBG, "Fifo partition at: 0x%p is: 0x%llx\n",
&bar0->tx_fifo_partition_0, (unsigned long long) val64);
- /*
- * Initialization of Tx_PA_CONFIG register to ignore packet
+ /*
+ * Initialization of Tx_PA_CONFIG register to ignore packet
* integrity checking.
*/
val64 = readq(&bar0->tx_pa_cfg);
@@ -770,85 +955,304 @@
}
writeq(val64, &bar0->rx_queue_priority);
- /*
- * Allocating equal share of memory to all the
+ /*
+ * Allocating equal share of memory to all the
* configured Rings.
*/
val64 = 0;
+ if (nic->device_type & XFRAME_II_DEVICE)
+ mem_size = 32;
+ else
+ mem_size = 64;
+
for (i = 0; i < config->rx_ring_num; i++) {
switch (i) {
case 0:
- mem_share = (64 / config->rx_ring_num +
- 64 % config->rx_ring_num);
+ mem_share = (mem_size / config->rx_ring_num +
+ mem_size % config->rx_ring_num);
val64 |= RX_QUEUE_CFG_Q0_SZ(mem_share);
continue;
case 1:
- mem_share = (64 / config->rx_ring_num);
+ mem_share = (mem_size / config->rx_ring_num);
val64 |= RX_QUEUE_CFG_Q1_SZ(mem_share);
continue;
case 2:
- mem_share = (64 / config->rx_ring_num);
+ mem_share = (mem_size / config->rx_ring_num);
val64 |= RX_QUEUE_CFG_Q2_SZ(mem_share);
continue;
case 3:
- mem_share = (64 / config->rx_ring_num);
+ mem_share = (mem_size / config->rx_ring_num);
val64 |= RX_QUEUE_CFG_Q3_SZ(mem_share);
continue;
case 4:
- mem_share = (64 / config->rx_ring_num);
+ mem_share = (mem_size / config->rx_ring_num);
val64 |= RX_QUEUE_CFG_Q4_SZ(mem_share);
continue;
case 5:
- mem_share = (64 / config->rx_ring_num);
+ mem_share = (mem_size / config->rx_ring_num);
val64 |= RX_QUEUE_CFG_Q5_SZ(mem_share);
continue;
case 6:
- mem_share = (64 / config->rx_ring_num);
+ mem_share = (mem_size / config->rx_ring_num);
val64 |= RX_QUEUE_CFG_Q6_SZ(mem_share);
continue;
case 7:
- mem_share = (64 / config->rx_ring_num);
+ mem_share = (mem_size / config->rx_ring_num);
val64 |= RX_QUEUE_CFG_Q7_SZ(mem_share);
continue;
}
}
writeq(val64, &bar0->rx_queue_cfg);
- /*
- * Initializing the Tx round robin registers to 0.
- * Filling Tx and Rx round robin registers as per the
- * number of FIFOs and Rings is still TODO.
+ /*
+ * Filling Tx round robin registers
+ * as per the number of FIFOs
*/
- writeq(0, &bar0->tx_w_round_robin_0);
- writeq(0, &bar0->tx_w_round_robin_1);
- writeq(0, &bar0->tx_w_round_robin_2);
- writeq(0, &bar0->tx_w_round_robin_3);
- writeq(0, &bar0->tx_w_round_robin_4);
+ switch (config->tx_fifo_num) {
+ case 1:
+ val64 = 0x0000000000000000ULL;
+ writeq(val64, &bar0->tx_w_round_robin_0);
+ writeq(val64, &bar0->tx_w_round_robin_1);
+ writeq(val64, &bar0->tx_w_round_robin_2);
+ writeq(val64, &bar0->tx_w_round_robin_3);
+ writeq(val64, &bar0->tx_w_round_robin_4);
+ break;
+ case 2:
+ val64 = 0x0000010000010000ULL;
+ writeq(val64, &bar0->tx_w_round_robin_0);
+ val64 = 0x0100000100000100ULL;
+ writeq(val64, &bar0->tx_w_round_robin_1);
+ val64 = 0x0001000001000001ULL;
+ writeq(val64, &bar0->tx_w_round_robin_2);
+ val64 = 0x0000010000010000ULL;
+ writeq(val64, &bar0->tx_w_round_robin_3);
+ val64 = 0x0100000000000000ULL;
+ writeq(val64, &bar0->tx_w_round_robin_4);
+ break;
+ case 3:
+ val64 = 0x0001000102000001ULL;
+ writeq(val64, &bar0->tx_w_round_robin_0);
+ val64 = 0x0001020000010001ULL;
+ writeq(val64, &bar0->tx_w_round_robin_1);
+ val64 = 0x0200000100010200ULL;
+ writeq(val64, &bar0->tx_w_round_robin_2);
+ val64 = 0x0001000102000001ULL;
+ writeq(val64, &bar0->tx_w_round_robin_3);
+ val64 = 0x0001020000000000ULL;
+ writeq(val64, &bar0->tx_w_round_robin_4);
+ break;
+ case 4:
+ val64 = 0x0001020300010200ULL;
+ writeq(val64, &bar0->tx_w_round_robin_0);
+ val64 = 0x0100000102030001ULL;
+ writeq(val64, &bar0->tx_w_round_robin_1);
+ val64 = 0x0200010000010203ULL;
+ writeq(val64, &bar0->tx_w_round_robin_2);
+ val64 = 0x0001020001000001ULL;
+ writeq(val64, &bar0->tx_w_round_robin_3);
+ val64 = 0x0203000100000000ULL;
+ writeq(val64, &bar0->tx_w_round_robin_4);
+ break;
+ case 5:
+ val64 = 0x0001000203000102ULL;
+ writeq(val64, &bar0->tx_w_round_robin_0);
+ val64 = 0x0001020001030004ULL;
+ writeq(val64, &bar0->tx_w_round_robin_1);
+ val64 = 0x0001000203000102ULL;
+ writeq(val64, &bar0->tx_w_round_robin_2);
+ val64 = 0x0001020001030004ULL;
+ writeq(val64, &bar0->tx_w_round_robin_3);
+ val64 = 0x0001000000000000ULL;
+ writeq(val64, &bar0->tx_w_round_robin_4);
+ break;
+ case 6:
+ val64 = 0x0001020304000102ULL;
+ writeq(val64, &bar0->tx_w_round_robin_0);
+ val64 = 0x0304050001020001ULL;
+ writeq(val64, &bar0->tx_w_round_robin_1);
+ val64 = 0x0203000100000102ULL;
+ writeq(val64, &bar0->tx_w_round_robin_2);
+ val64 = 0x0304000102030405ULL;
+ writeq(val64, &bar0->tx_w_round_robin_3);
+ val64 = 0x0001000200000000ULL;
+ writeq(val64, &bar0->tx_w_round_robin_4);
+ break;
+ case 7:
+ val64 = 0x0001020001020300ULL;
+ writeq(val64, &bar0->tx_w_round_robin_0);
+ val64 = 0x0102030400010203ULL;
+ writeq(val64, &bar0->tx_w_round_robin_1);
+ val64 = 0x0405060001020001ULL;
+ writeq(val64, &bar0->tx_w_round_robin_2);
+ val64 = 0x0304050000010200ULL;
+ writeq(val64, &bar0->tx_w_round_robin_3);
+ val64 = 0x0102030000000000ULL;
+ writeq(val64, &bar0->tx_w_round_robin_4);
+ break;
+ case 8:
+ val64 = 0x0001020300040105ULL;
+ writeq(val64, &bar0->tx_w_round_robin_0);
+ val64 = 0x0200030106000204ULL;
+ writeq(val64, &bar0->tx_w_round_robin_1);
+ val64 = 0x0103000502010007ULL;
+ writeq(val64, &bar0->tx_w_round_robin_2);
+ val64 = 0x0304010002060500ULL;
+ writeq(val64, &bar0->tx_w_round_robin_3);
+ val64 = 0x0103020400000000ULL;
+ writeq(val64, &bar0->tx_w_round_robin_4);
+ break;
+ }
- /*
- * TODO
- * Disable Rx steering. Hard coding all packets be steered to
- * Queue 0 for now.
- */
- val64 = 0x8080808080808080ULL;
- writeq(val64, &bar0->rts_qos_steering);
+ /* Filling the Rx round robin registers as per the
+ * number of Rings and steering based on QoS.
+ */
+ switch (config->rx_ring_num) {
+ case 1:
+ val64 = 0x8080808080808080ULL;
+ writeq(val64, &bar0->rts_qos_steering);
+ break;
+ case 2:
+ val64 = 0x0000010000010000ULL;
+ writeq(val64, &bar0->rx_w_round_robin_0);
+ val64 = 0x0100000100000100ULL;
+ writeq(val64, &bar0->rx_w_round_robin_1);
+ val64 = 0x0001000001000001ULL;
+ writeq(val64, &bar0->rx_w_round_robin_2);
+ val64 = 0x0000010000010000ULL;
+ writeq(val64, &bar0->rx_w_round_robin_3);
+ val64 = 0x0100000000000000ULL;
+ writeq(val64, &bar0->rx_w_round_robin_4);
+
+ val64 = 0x8080808040404040ULL;
+ writeq(val64, &bar0->rts_qos_steering);
+ break;
+ case 3:
+ val64 = 0x0001000102000001ULL;
+ writeq(val64, &bar0->rx_w_round_robin_0);
+ val64 = 0x0001020000010001ULL;
+ writeq(val64, &bar0->rx_w_round_robin_1);
+ val64 = 0x0200000100010200ULL;
+ writeq(val64, &bar0->rx_w_round_robin_2);
+ val64 = 0x0001000102000001ULL;
+ writeq(val64, &bar0->rx_w_round_robin_3);
+ val64 = 0x0001020000000000ULL;
+ writeq(val64, &bar0->rx_w_round_robin_4);
+
+ val64 = 0x8080804040402020ULL;
+ writeq(val64, &bar0->rts_qos_steering);
+ break;
+ case 4:
+ val64 = 0x0001020300010200ULL;
+ writeq(val64, &bar0->rx_w_round_robin_0);
+ val64 = 0x0100000102030001ULL;
+ writeq(val64, &bar0->rx_w_round_robin_1);
+ val64 = 0x0200010000010203ULL;
+ writeq(val64, &bar0->rx_w_round_robin_2);
+ val64 = 0x0001020001000001ULL;
+ writeq(val64, &bar0->rx_w_round_robin_3);
+ val64 = 0x0203000100000000ULL;
+ writeq(val64, &bar0->rx_w_round_robin_4);
+
+ val64 = 0x8080404020201010ULL;
+ writeq(val64, &bar0->rts_qos_steering);
+ break;
+ case 5:
+ val64 = 0x0001000203000102ULL;
+ writeq(val64, &bar0->rx_w_round_robin_0);
+ val64 = 0x0001020001030004ULL;
+ writeq(val64, &bar0->rx_w_round_robin_1);
+ val64 = 0x0001000203000102ULL;
+ writeq(val64, &bar0->rx_w_round_robin_2);
+ val64 = 0x0001020001030004ULL;
+ writeq(val64, &bar0->rx_w_round_robin_3);
+ val64 = 0x0001000000000000ULL;
+ writeq(val64, &bar0->rx_w_round_robin_4);
+
+ val64 = 0x8080404020201008ULL;
+ writeq(val64, &bar0->rts_qos_steering);
+ break;
+ case 6:
+ val64 = 0x0001020304000102ULL;
+ writeq(val64, &bar0->rx_w_round_robin_0);
+ val64 = 0x0304050001020001ULL;
+ writeq(val64, &bar0->rx_w_round_robin_1);
+ val64 = 0x0203000100000102ULL;
+ writeq(val64, &bar0->rx_w_round_robin_2);
+ val64 = 0x0304000102030405ULL;
+ writeq(val64, &bar0->rx_w_round_robin_3);
+ val64 = 0x0001000200000000ULL;
+ writeq(val64, &bar0->rx_w_round_robin_4);
+
+ val64 = 0x8080404020100804ULL;
+ writeq(val64, &bar0->rts_qos_steering);
+ break;
+ case 7:
+ val64 = 0x0001020001020300ULL;
+ writeq(val64, &bar0->rx_w_round_robin_0);
+ val64 = 0x0102030400010203ULL;
+ writeq(val64, &bar0->rx_w_round_robin_1);
+ val64 = 0x0405060001020001ULL;
+ writeq(val64, &bar0->rx_w_round_robin_2);
+ val64 = 0x0304050000010200ULL;
+ writeq(val64, &bar0->rx_w_round_robin_3);
+ val64 = 0x0102030000000000ULL;
+ writeq(val64, &bar0->rx_w_round_robin_4);
+
+ val64 = 0x8080402010080402ULL;
+ writeq(val64, &bar0->rts_qos_steering);
+ break;
+ case 8:
+ val64 = 0x0001020300040105ULL;
+ writeq(val64, &bar0->rx_w_round_robin_0);
+ val64 = 0x0200030106000204ULL;
+ writeq(val64, &bar0->rx_w_round_robin_1);
+ val64 = 0x0103000502010007ULL;
+ writeq(val64, &bar0->rx_w_round_robin_2);
+ val64 = 0x0304010002060500ULL;
+ writeq(val64, &bar0->rx_w_round_robin_3);
+ val64 = 0x0103020400000000ULL;
+ writeq(val64, &bar0->rx_w_round_robin_4);
+
+ val64 = 0x8040201008040201ULL;
+ writeq(val64, &bar0->rts_qos_steering);
+ break;
+ }
/* UDP Fix */
val64 = 0;
- for (i = 1; i < 8; i++)
+ for (i = 0; i < 8; i++)
writeq(val64, &bar0->rts_frm_len_n[i]);
- /* Set rts_frm_len register for fifo 0 */
- writeq(MAC_RTS_FRM_LEN_SET(dev->mtu + 22),
- &bar0->rts_frm_len_n[0]);
+ /* Set the default rts frame length for the rings configured */
+ val64 = MAC_RTS_FRM_LEN_SET(dev->mtu+22);
+ for (i = 0 ; i < config->rx_ring_num ; i++)
+ writeq(val64, &bar0->rts_frm_len_n[i]);
- /* Enable statistics */
+ /* Set the frame length for the configured rings
+ * desired by the user
+ */
+ for (i = 0; i < config->rx_ring_num; i++) {
+ /* If rts_frm_len[i] == 0 then it is assumed that user not
+ * specified frame length steering.
+ * If the user provides the frame length then program
+ * the rts_frm_len register for those values or else
+ * leave it as it is.
+ */
+ if (rts_frm_len[i] != 0) {
+ writeq(MAC_RTS_FRM_LEN_SET(rts_frm_len[i]),
+ &bar0->rts_frm_len_n[i]);
+ }
+ }
+
+ /* Program statistics memory */
writeq(mac_control->stats_mem_phy, &bar0->stat_addr);
- val64 = SET_UPDT_PERIOD(Stats_refresh_time) |
- STAT_CFG_STAT_RO | STAT_CFG_STAT_EN;
- writeq(val64, &bar0->stat_cfg);
- /*
+ if (nic->device_type == XFRAME_II_DEVICE) {
+ val64 = STAT_BC(0x320);
+ writeq(val64, &bar0->stat_byte_cnt);
+ }
+
+ /*
* Initializing the sampling rate for the device to calculate the
* bandwidth utilization.
*/
@@ -857,30 +1261,38 @@
writeq(val64, &bar0->mac_link_util);
- /*
- * Initializing the Transmit and Receive Traffic Interrupt
+ /*
+ * Initializing the Transmit and Receive Traffic Interrupt
* Scheme.
*/
- /* TTI Initialization. Default Tx timer gets us about
+ /*
+ * TTI Initialization. Default Tx timer gets us about
* 250 interrupts per sec. Continuous interrupts are enabled
* by default.
*/
- val64 = TTI_DATA1_MEM_TX_TIMER_VAL(0x2078) |
- TTI_DATA1_MEM_TX_URNG_A(0xA) |
+ if (nic->device_type == XFRAME_II_DEVICE) {
+ int count = (nic->config.bus_speed * 125)/2;
+ val64 = TTI_DATA1_MEM_TX_TIMER_VAL(count);
+ } else {
+
+ val64 = TTI_DATA1_MEM_TX_TIMER_VAL(0x2078);
+ }
+ val64 |= TTI_DATA1_MEM_TX_URNG_A(0xA) |
TTI_DATA1_MEM_TX_URNG_B(0x10) |
- TTI_DATA1_MEM_TX_URNG_C(0x30) | TTI_DATA1_MEM_TX_TIMER_AC_EN |
- TTI_DATA1_MEM_TX_TIMER_CI_EN;
+ TTI_DATA1_MEM_TX_URNG_C(0x30) | TTI_DATA1_MEM_TX_TIMER_AC_EN;
+ if (use_continuous_tx_intrs)
+ val64 |= TTI_DATA1_MEM_TX_TIMER_CI_EN;
writeq(val64, &bar0->tti_data1_mem);
val64 = TTI_DATA2_MEM_TX_UFC_A(0x10) |
TTI_DATA2_MEM_TX_UFC_B(0x20) |
- TTI_DATA2_MEM_TX_UFC_C(0x40) | TTI_DATA2_MEM_TX_UFC_D(0x80);
+ TTI_DATA2_MEM_TX_UFC_C(0x70) | TTI_DATA2_MEM_TX_UFC_D(0x80);
writeq(val64, &bar0->tti_data2_mem);
val64 = TTI_CMD_MEM_WE | TTI_CMD_MEM_STROBE_NEW_CMD;
writeq(val64, &bar0->tti_command_mem);
- /*
+ /*
* Once the operation completes, the Strobe bit of the command
* register will be reset. We poll for this particular condition
* We wait for a maximum of 500ms for the operation to complete,
@@ -901,52 +1313,97 @@
time++;
}
- /* RTI Initialization */
- val64 = RTI_DATA1_MEM_RX_TIMER_VAL(0xFFF) |
- RTI_DATA1_MEM_RX_URNG_A(0xA) |
- RTI_DATA1_MEM_RX_URNG_B(0x10) |
- RTI_DATA1_MEM_RX_URNG_C(0x30) | RTI_DATA1_MEM_RX_TIMER_AC_EN;
+ if (nic->config.bimodal) {
+ int k = 0;
+ for (k = 0; k < config->rx_ring_num; k++) {
+ val64 = TTI_CMD_MEM_WE | TTI_CMD_MEM_STROBE_NEW_CMD;
+ val64 |= TTI_CMD_MEM_OFFSET(0x38+k);
+ writeq(val64, &bar0->tti_command_mem);
- writeq(val64, &bar0->rti_data1_mem);
-
- val64 = RTI_DATA2_MEM_RX_UFC_A(0x1) |
- RTI_DATA2_MEM_RX_UFC_B(0x2) |
- RTI_DATA2_MEM_RX_UFC_C(0x40) | RTI_DATA2_MEM_RX_UFC_D(0x80);
- writeq(val64, &bar0->rti_data2_mem);
-
- val64 = RTI_CMD_MEM_WE | RTI_CMD_MEM_STROBE_NEW_CMD;
- writeq(val64, &bar0->rti_command_mem);
-
- /*
- * Once the operation completes, the Strobe bit of the command
- * register will be reset. We poll for this particular condition
- * We wait for a maximum of 500ms for the operation to complete,
- * if it's not complete by then we return error.
- */
- time = 0;
- while (TRUE) {
- val64 = readq(&bar0->rti_command_mem);
- if (!(val64 & TTI_CMD_MEM_STROBE_NEW_CMD)) {
- break;
+ /*
+ * Once the operation completes, the Strobe bit of the command
+ * register will be reset. We poll for this particular condition
+ * We wait for a maximum of 500ms for the operation to complete,
+ * if it's not complete by then we return error.
+ */
+ time = 0;
+ while (TRUE) {
+ val64 = readq(&bar0->tti_command_mem);
+ if (!(val64 & TTI_CMD_MEM_STROBE_NEW_CMD)) {
+ break;
+ }
+ if (time > 10) {
+ DBG_PRINT(ERR_DBG,
+ "%s: TTI init Failed\n",
+ dev->name);
+ return -1;
+ }
+ time++;
+ msleep(50);
+ }
}
- if (time > 10) {
- DBG_PRINT(ERR_DBG, "%s: RTI init Failed\n",
- dev->name);
- return -1;
+ } else {
+
+ /* RTI Initialization */
+ if (nic->device_type == XFRAME_II_DEVICE) {
+ /*
+ * Programmed to generate Apprx 500 Intrs per
+ * second
+ */
+ int count = (nic->config.bus_speed * 125)/4;
+ val64 = RTI_DATA1_MEM_RX_TIMER_VAL(count);
+ } else {
+ val64 = RTI_DATA1_MEM_RX_TIMER_VAL(0xFFF);
}
- time++;
- msleep(50);
+ val64 |= RTI_DATA1_MEM_RX_URNG_A(0xA) |
+ RTI_DATA1_MEM_RX_URNG_B(0x10) |
+ RTI_DATA1_MEM_RX_URNG_C(0x30) | RTI_DATA1_MEM_RX_TIMER_AC_EN;
+
+ writeq(val64, &bar0->rti_data1_mem);
+
+ val64 = RTI_DATA2_MEM_RX_UFC_A(0x1) |
+ RTI_DATA2_MEM_RX_UFC_B(0x2) |
+ RTI_DATA2_MEM_RX_UFC_C(0x40) | RTI_DATA2_MEM_RX_UFC_D(0x80);
+ writeq(val64, &bar0->rti_data2_mem);
+
+ for (i = 0; i < config->rx_ring_num; i++) {
+ val64 = RTI_CMD_MEM_WE | RTI_CMD_MEM_STROBE_NEW_CMD
+ | RTI_CMD_MEM_OFFSET(i);
+ writeq(val64, &bar0->rti_command_mem);
+
+ /*
+ * Once the operation completes, the Strobe bit of the
+ * command register will be reset. We poll for this
+ * particular condition. We wait for a maximum of 500ms
+ * for the operation to complete, if it's not complete
+ * by then we return error.
+ */
+ time = 0;
+ while (TRUE) {
+ val64 = readq(&bar0->rti_command_mem);
+ if (!(val64 & RTI_CMD_MEM_STROBE_NEW_CMD)) {
+ break;
+ }
+ if (time > 10) {
+ DBG_PRINT(ERR_DBG, "%s: RTI init Failed\n",
+ dev->name);
+ return -1;
+ }
+ time++;
+ msleep(50);
+ }
+ }
}
- /*
- * Initializing proper values as Pause threshold into all
+ /*
+ * Initializing proper values as Pause threshold into all
* the 8 Queues on Rx side.
*/
writeq(0xffbbffbbffbbffbbULL, &bar0->mc_pause_thresh_q0q3);
writeq(0xffbbffbbffbbffbbULL, &bar0->mc_pause_thresh_q4q7);
/* Disable RMAC PAD STRIPPING */
- add = &bar0->mac_cfg;
+ add = (void *) &bar0->mac_cfg;
val64 = readq(&bar0->mac_cfg);
val64 &= ~(MAC_CFG_RMAC_STRIP_PAD);
writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
@@ -955,8 +1412,8 @@
writel((u32) (val64 >> 32), (add + 4));
val64 = readq(&bar0->mac_cfg);
- /*
- * Set the time value to be inserted in the pause frame
+ /*
+ * Set the time value to be inserted in the pause frame
* generated by xena.
*/
val64 = readq(&bar0->rmac_pause_cfg);
@@ -964,7 +1421,7 @@
val64 |= RMAC_PAUSE_HG_PTIME(nic->mac_control.rmac_pause_time);
writeq(val64, &bar0->rmac_pause_cfg);
- /*
+ /*
* Set the Threshold Limit for Generating the pause frame
* If the amount of data in any Queue exceeds ratio of
* (mac_control.mc_pause_threshold_q0q3 or q4q7)/256
@@ -988,25 +1445,54 @@
}
writeq(val64, &bar0->mc_pause_thresh_q4q7);
- /*
- * TxDMA will stop Read request if the number of read split has
+ /*
+ * TxDMA will stop Read request if the number of read split has
* exceeded the limit pointed by shared_splits
*/
val64 = readq(&bar0->pic_control);
val64 |= PIC_CNTL_SHARED_SPLITS(shared_splits);
writeq(val64, &bar0->pic_control);
+ /*
+ * Programming the Herc to split every write transaction
+ * that does not start on an ADB to reduce disconnects.
+ */
+ if (nic->device_type == XFRAME_II_DEVICE) {
+ val64 = WREQ_SPLIT_MASK_SET_MASK(255);
+ writeq(val64, &bar0->wreq_split_mask);
+ }
+
+ /* Setting Link stability period to 64 ms */
+ if (nic->device_type == XFRAME_II_DEVICE) {
+ val64 = MISC_LINK_STABILITY_PRD(3);
+ writeq(val64, &bar0->misc_control);
+ }
+
return SUCCESS;
}
+#define LINK_UP_DOWN_INTERRUPT 1
+#define MAC_RMAC_ERR_TIMER 2
-/**
- * en_dis_able_nic_intrs - Enable or Disable the interrupts
+#if defined(CONFIG_MSI_MODE) || defined(CONFIG_MSIX_MODE)
+#define s2io_link_fault_indication(x) MAC_RMAC_ERR_TIMER
+#else
+int s2io_link_fault_indication(nic_t *nic)
+{
+ if (nic->device_type == XFRAME_II_DEVICE)
+ return LINK_UP_DOWN_INTERRUPT;
+ else
+ return MAC_RMAC_ERR_TIMER;
+}
+#endif
+
+/**
+ * en_dis_able_nic_intrs - Enable or Disable the interrupts
* @nic: device private variable,
* @mask: A mask indicating which Intr block must be modified and,
* @flag: A flag indicating whether to enable or disable the Intrs.
* Description: This function will either disable or enable the interrupts
- * depending on the flag argument. The mask argument can be used to
- * enable/disable any Intr block.
+ * depending on the flag argument. The mask argument can be used to
+ * enable/disable any Intr block.
* Return Value: NONE.
*/
@@ -1024,20 +1510,31 @@
temp64 = readq(&bar0->general_int_mask);
temp64 &= ~((u64) val64);
writeq(temp64, &bar0->general_int_mask);
- /*
- * Disabled all PCIX, Flash, MDIO, IIC and GPIO
- * interrupts for now.
- * TODO
+ /*
+ * If Hercules adapter enable GPIO otherwise
+ * disabled all PCIX, Flash, MDIO, IIC and GPIO
+ * interrupts for now.
+ * TODO
*/
- writeq(DISABLE_ALL_INTRS, &bar0->pic_int_mask);
- /*
+ if (s2io_link_fault_indication(nic) ==
+ LINK_UP_DOWN_INTERRUPT ) {
+ temp64 = readq(&bar0->pic_int_mask);
+ temp64 &= ~((u64) PIC_INT_GPIO);
+ writeq(temp64, &bar0->pic_int_mask);
+ temp64 = readq(&bar0->gpio_int_mask);
+ temp64 &= ~((u64) GPIO_INT_MASK_LINK_UP);
+ writeq(temp64, &bar0->gpio_int_mask);
+ } else {
+ writeq(DISABLE_ALL_INTRS, &bar0->pic_int_mask);
+ }
+ /*
* No MSI Support is available presently, so TTI and
* RTI interrupts are also disabled.
*/
} else if (flag == DISABLE_INTRS) {
- /*
- * Disable PIC Intrs in the general
- * intr mask register
+ /*
+ * Disable PIC Intrs in the general
+ * intr mask register
*/
writeq(DISABLE_ALL_INTRS, &bar0->pic_int_mask);
temp64 = readq(&bar0->general_int_mask);
@@ -1055,27 +1552,27 @@
temp64 = readq(&bar0->general_int_mask);
temp64 &= ~((u64) val64);
writeq(temp64, &bar0->general_int_mask);
- /*
- * Keep all interrupts other than PFC interrupt
+ /*
+ * Keep all interrupts other than PFC interrupt
* and PCC interrupt disabled in DMA level.
*/
val64 = DISABLE_ALL_INTRS & ~(TXDMA_PFC_INT_M |
TXDMA_PCC_INT_M);
writeq(val64, &bar0->txdma_int_mask);
- /*
- * Enable only the MISC error 1 interrupt in PFC block
+ /*
+ * Enable only the MISC error 1 interrupt in PFC block
*/
val64 = DISABLE_ALL_INTRS & (~PFC_MISC_ERR_1);
writeq(val64, &bar0->pfc_err_mask);
- /*
- * Enable only the FB_ECC error interrupt in PCC block
+ /*
+ * Enable only the FB_ECC error interrupt in PCC block
*/
val64 = DISABLE_ALL_INTRS & (~PCC_FB_ECC_ERR);
writeq(val64, &bar0->pcc_err_mask);
} else if (flag == DISABLE_INTRS) {
- /*
- * Disable TxDMA Intrs in the general intr mask
- * register
+ /*
+ * Disable TxDMA Intrs in the general intr mask
+ * register
*/
writeq(DISABLE_ALL_INTRS, &bar0->txdma_int_mask);
writeq(DISABLE_ALL_INTRS, &bar0->pfc_err_mask);
@@ -1093,15 +1590,15 @@
temp64 = readq(&bar0->general_int_mask);
temp64 &= ~((u64) val64);
writeq(temp64, &bar0->general_int_mask);
- /*
- * All RxDMA block interrupts are disabled for now
- * TODO
+ /*
+ * All RxDMA block interrupts are disabled for now
+ * TODO
*/
writeq(DISABLE_ALL_INTRS, &bar0->rxdma_int_mask);
} else if (flag == DISABLE_INTRS) {
- /*
- * Disable RxDMA Intrs in the general intr mask
- * register
+ /*
+ * Disable RxDMA Intrs in the general intr mask
+ * register
*/
writeq(DISABLE_ALL_INTRS, &bar0->rxdma_int_mask);
temp64 = readq(&bar0->general_int_mask);
@@ -1118,22 +1615,13 @@
temp64 = readq(&bar0->general_int_mask);
temp64 &= ~((u64) val64);
writeq(temp64, &bar0->general_int_mask);
- /*
- * All MAC block error interrupts are disabled for now
- * except the link status change interrupt.
+ /*
+ * All MAC block error interrupts are disabled for now
* TODO
*/
- val64 = MAC_INT_STATUS_RMAC_INT;
- temp64 = readq(&bar0->mac_int_mask);
- temp64 &= ~((u64) val64);
- writeq(temp64, &bar0->mac_int_mask);
-
- val64 = readq(&bar0->mac_rmac_err_mask);
- val64 &= ~((u64) RMAC_LINK_STATE_CHANGE_INT);
- writeq(val64, &bar0->mac_rmac_err_mask);
} else if (flag == DISABLE_INTRS) {
- /*
- * Disable MAC Intrs in the general intr mask register
+ /*
+ * Disable MAC Intrs in the general intr mask register
*/
writeq(DISABLE_ALL_INTRS, &bar0->mac_int_mask);
writeq(DISABLE_ALL_INTRS,
@@ -1152,14 +1640,14 @@
temp64 = readq(&bar0->general_int_mask);
temp64 &= ~((u64) val64);
writeq(temp64, &bar0->general_int_mask);
- /*
+ /*
* All XGXS block error interrupts are disabled for now
- * TODO
+ * TODO
*/
writeq(DISABLE_ALL_INTRS, &bar0->xgxs_int_mask);
} else if (flag == DISABLE_INTRS) {
- /*
- * Disable MC Intrs in the general intr mask register
+ /*
+ * Disable MC Intrs in the general intr mask register
*/
writeq(DISABLE_ALL_INTRS, &bar0->xgxs_int_mask);
temp64 = readq(&bar0->general_int_mask);
@@ -1175,11 +1663,11 @@
temp64 = readq(&bar0->general_int_mask);
temp64 &= ~((u64) val64);
writeq(temp64, &bar0->general_int_mask);
- /*
- * All MC block error interrupts are disabled for now
- * TODO
+ /*
+ * Enable all MC Intrs.
*/
- writeq(DISABLE_ALL_INTRS, &bar0->mc_int_mask);
+ writeq(0x0, &bar0->mc_int_mask);
+ writeq(0x0, &bar0->mc_err_mask);
} else if (flag == DISABLE_INTRS) {
/*
* Disable MC Intrs in the general intr mask register
@@ -1199,14 +1687,14 @@
temp64 = readq(&bar0->general_int_mask);
temp64 &= ~((u64) val64);
writeq(temp64, &bar0->general_int_mask);
- /*
+ /*
* Enable all the Tx side interrupts
- * writing 0 Enables all 64 TX interrupt levels
+ * writing 0 Enables all 64 TX interrupt levels
*/
writeq(0x0, &bar0->tx_traffic_mask);
} else if (flag == DISABLE_INTRS) {
- /*
- * Disable Tx Traffic Intrs in the general intr mask
+ /*
+ * Disable Tx Traffic Intrs in the general intr mask
* register.
*/
writeq(DISABLE_ALL_INTRS, &bar0->tx_traffic_mask);
@@ -1226,8 +1714,8 @@
/* writing 0 Enables all 8 RX interrupt levels */
writeq(0x0, &bar0->rx_traffic_mask);
} else if (flag == DISABLE_INTRS) {
- /*
- * Disable Rx Traffic Intrs in the general intr mask
+ /*
+ * Disable Rx Traffic Intrs in the general intr mask
* register.
*/
writeq(DISABLE_ALL_INTRS, &bar0->rx_traffic_mask);
@@ -1238,24 +1726,66 @@
}
}
-/**
- * verify_xena_quiescence - Checks whether the H/W is ready
+static int check_prc_pcc_state(u64 val64, int flag, int rev_id, int herc)
+{
+ int ret = 0;
+
+ if (flag == FALSE) {
+ if ((!herc && (rev_id >= 4)) || herc) {
+ if (!(val64 & ADAPTER_STATUS_RMAC_PCC_IDLE) &&
+ ((val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) ==
+ ADAPTER_STATUS_RC_PRC_QUIESCENT)) {
+ ret = 1;
+ }
+ }else {
+ if (!(val64 & ADAPTER_STATUS_RMAC_PCC_FOUR_IDLE) &&
+ ((val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) ==
+ ADAPTER_STATUS_RC_PRC_QUIESCENT)) {
+ ret = 1;
+ }
+ }
+ } else {
+ if ((!herc && (rev_id >= 4)) || herc) {
+ if (((val64 & ADAPTER_STATUS_RMAC_PCC_IDLE) ==
+ ADAPTER_STATUS_RMAC_PCC_IDLE) &&
+ (!(val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) ||
+ ((val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) ==
+ ADAPTER_STATUS_RC_PRC_QUIESCENT))) {
+ ret = 1;
+ }
+ } else {
+ if (((val64 & ADAPTER_STATUS_RMAC_PCC_FOUR_IDLE) ==
+ ADAPTER_STATUS_RMAC_PCC_FOUR_IDLE) &&
+ (!(val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) ||
+ ((val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) ==
+ ADAPTER_STATUS_RC_PRC_QUIESCENT))) {
+ ret = 1;
+ }
+ }
+ }
+
+ return ret;
+}
+/**
+ * verify_xena_quiescence - Checks whether the H/W is ready
* @val64 : Value read from adapter status register.
* @flag : indicates if the adapter enable bit was ever written once
* before.
* Description: Returns whether the H/W is ready to go or not. Depending
- * on whether adapter enable bit was written or not the comparison
+ * on whether adapter enable bit was written or not the comparison
* differs and the calling function passes the input argument flag to
* indicate this.
- * Return: 1 If xena is quiescence
+ * Return: 1 If xena is quiescence
* 0 If Xena is not quiescence
*/
-static int verify_xena_quiescence(u64 val64, int flag)
+static int verify_xena_quiescence(nic_t *sp, u64 val64, int flag)
{
- int ret = 0;
+ int ret = 0, herc;
u64 tmp64 = ~((u64) val64);
+ int rev_id = get_xena_rev_id(sp->pdev);
+ herc = (sp->device_type == XFRAME_II_DEVICE);
if (!
(tmp64 &
(ADAPTER_STATUS_TDMA_READY | ADAPTER_STATUS_RDMA_READY |
@@ -1263,25 +1793,7 @@
ADAPTER_STATUS_PIC_QUIESCENT | ADAPTER_STATUS_MC_DRAM_READY |
ADAPTER_STATUS_MC_QUEUES_READY | ADAPTER_STATUS_M_PLL_LOCK |
ADAPTER_STATUS_P_PLL_LOCK))) {
- if (flag == FALSE) {
- if (!(val64 & ADAPTER_STATUS_RMAC_PCC_IDLE) &&
- ((val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) ==
- ADAPTER_STATUS_RC_PRC_QUIESCENT)) {
-
- ret = 1;
-
- }
- } else {
- if (((val64 & ADAPTER_STATUS_RMAC_PCC_IDLE) ==
- ADAPTER_STATUS_RMAC_PCC_IDLE) &&
- (!(val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) ||
- ((val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) ==
- ADAPTER_STATUS_RC_PRC_QUIESCENT))) {
-
- ret = 1;
-
- }
- }
+ ret = check_prc_pcc_state(val64, flag, rev_id, herc);
}
return ret;
@@ -1290,12 +1802,12 @@
/**
* fix_mac_address - Fix for Mac addr problem on Alpha platforms
* @sp: Pointer to device specifc structure
- * Description :
+ * Description :
* New procedure to clear mac address reading problems on Alpha platforms
*
*/
-static void fix_mac_address(nic_t * sp)
+void fix_mac_address(nic_t * sp)
{
XENA_dev_config_t __iomem *bar0 = sp->bar0;
u64 val64;
@@ -1303,20 +1815,21 @@
while (fix_mac[i] != END_SIGN) {
writeq(fix_mac[i++], &bar0->gpio_control);
+ udelay(10);
val64 = readq(&bar0->gpio_control);
}
}
/**
- * start_nic - Turns the device on
+ * start_nic - Turns the device on
* @nic : device private variable.
- * Description:
- * This function actually turns the device on. Before this function is
- * called,all Registers are configured from their reset states
- * and shared memory is allocated but the NIC is still quiescent. On
+ * Description:
+ * This function actually turns the device on. Before this function is
+ * called,all Registers are configured from their reset states
+ * and shared memory is allocated but the NIC is still quiescent. On
* calling this function, the device interrupts are cleared and the NIC is
* literally switched on by writing into the adapter control register.
- * Return Value:
+ * Return Value:
* SUCCESS on success and -1 on failure.
*/
@@ -1325,8 +1838,8 @@
XENA_dev_config_t __iomem *bar0 = nic->bar0;
struct net_device *dev = nic->dev;
register u64 val64 = 0;
- u16 interruptible, i;
- u16 subid;
+ u16 interruptible;
+ u16 subid, i;
mac_info_t *mac_control;
struct config_param *config;
@@ -1335,10 +1848,12 @@
/* PRC Initialization and configuration */
for (i = 0; i < config->rx_ring_num; i++) {
- writeq((u64) nic->rx_blocks[i][0].block_dma_addr,
+ writeq((u64) mac_control->rings[i].rx_blocks[0].block_dma_addr,
&bar0->prc_rxd0_n[i]);
val64 = readq(&bar0->prc_ctrl_n[i]);
+ if (nic->config.bimodal)
+ val64 |= PRC_CTRL_BIMODAL_INTERRUPT;
#ifndef CONFIG_2BUFF_MODE
val64 |= PRC_CTRL_RC_ENABLED;
#else
@@ -1354,7 +1869,7 @@
writeq(val64, &bar0->rx_pa_cfg);
#endif
- /*
+ /*
* Enabling MC-RLDRAM. After enabling the device, we timeout
* for around 100ms, which is approximately the time required
* for the device to be ready for operation.
@@ -1364,27 +1879,27 @@
SPECIAL_REG_WRITE(val64, &bar0->mc_rldram_mrs, UF);
val64 = readq(&bar0->mc_rldram_mrs);
- msleep(100); /* Delay by around 100 ms. */
+ msleep(100); /* Delay by around 100 ms. */
/* Enabling ECC Protection. */
val64 = readq(&bar0->adapter_control);
val64 &= ~ADAPTER_ECC_EN;
writeq(val64, &bar0->adapter_control);
- /*
- * Clearing any possible Link state change interrupts that
+ /*
+ * Clearing any possible Link state change interrupts that
* could have popped up just before Enabling the card.
*/
val64 = readq(&bar0->mac_rmac_err_reg);
if (val64)
writeq(val64, &bar0->mac_rmac_err_reg);
- /*
- * Verify if the device is ready to be enabled, if so enable
+ /*
+ * Verify if the device is ready to be enabled, if so enable
* it.
*/
val64 = readq(&bar0->adapter_status);
- if (!verify_xena_quiescence(val64, nic->device_enabled_once)) {
+ if (!verify_xena_quiescence(nic, val64, nic->device_enabled_once)) {
DBG_PRINT(ERR_DBG, "%s: device is not ready, ", dev->name);
DBG_PRINT(ERR_DBG, "Adapter status reads: 0x%llx\n",
(unsigned long long) val64);
@@ -1392,16 +1907,18 @@
}
/* Enable select interrupts */
- interruptible = TX_TRAFFIC_INTR | RX_TRAFFIC_INTR | TX_MAC_INTR |
- RX_MAC_INTR;
+ interruptible = TX_TRAFFIC_INTR | RX_TRAFFIC_INTR;
+ interruptible |= TX_PIC_INTR | RX_PIC_INTR;
+ interruptible |= TX_MAC_INTR | RX_MAC_INTR;
+
en_dis_able_nic_intrs(nic, interruptible, ENABLE_INTRS);
- /*
+ /*
* With some switches, link might be already up at this point.
- * Because of this weird behavior, when we enable laser,
- * we may not get link. We need to handle this. We cannot
- * figure out which switch is misbehaving. So we are forced to
- * make a global change.
+ * Because of this weird behavior, when we enable laser,
+ * we may not get link. We need to handle this. We cannot
+ * figure out which switch is misbehaving. So we are forced to
+ * make a global change.
*/
/* Enabling Laser. */
@@ -1411,44 +1928,30 @@
/* SXE-002: Initialize link and activity LED */
subid = nic->pdev->subsystem_device;
- if ((subid & 0xFF) >= 0x07) {
+ if (((subid & 0xFF) >= 0x07) &&
+ (nic->device_type == XFRAME_I_DEVICE)) {
val64 = readq(&bar0->gpio_control);
val64 |= 0x0000800000000000ULL;
writeq(val64, &bar0->gpio_control);
val64 = 0x0411040400000000ULL;
- writeq(val64, (void __iomem *) bar0 + 0x2700);
+ writeq(val64, (void __iomem *) ((u8 *) bar0 + 0x2700));
}
- /*
- * Don't see link state interrupts on certain switches, so
+ /*
+ * Don't see link state interrupts on certain switches, so
* directly scheduling a link state task from here.
*/
schedule_work(&nic->set_link_task);
- /*
- * Here we are performing soft reset on XGXS to
- * force link down. Since link is already up, we will get
- * link state change interrupt after this reset
- */
- SPECIAL_REG_WRITE(0x80010515001E0000ULL, &bar0->dtx_control, UF);
- val64 = readq(&bar0->dtx_control);
- udelay(50);
- SPECIAL_REG_WRITE(0x80010515001E00E0ULL, &bar0->dtx_control, UF);
- val64 = readq(&bar0->dtx_control);
- udelay(50);
- SPECIAL_REG_WRITE(0x80070515001F00E4ULL, &bar0->dtx_control, UF);
- val64 = readq(&bar0->dtx_control);
- udelay(50);
-
return SUCCESS;
}
-/**
- * free_tx_buffers - Free all queued Tx buffers
+/**
+ * free_tx_buffers - Free all queued Tx buffers
* @nic : device private variable.
- * Description:
+ * Description:
* Free all queued Tx buffers.
- * Return Value: void
+ * Return Value: void
*/
static void free_tx_buffers(struct s2io_nic *nic)
@@ -1459,39 +1962,61 @@
int i, j;
mac_info_t *mac_control;
struct config_param *config;
- int cnt = 0;
+ int cnt = 0, frg_cnt;
mac_control = &nic->mac_control;
config = &nic->config;
for (i = 0; i < config->tx_fifo_num; i++) {
for (j = 0; j < config->tx_cfg[i].fifo_len - 1; j++) {
- txdp = (TxD_t *) nic->list_info[i][j].
+ txdp = (TxD_t *) mac_control->fifos[i].list_info[j].
list_virt_addr;
skb =
(struct sk_buff *) ((unsigned long) txdp->
Host_Control);
if (skb == NULL) {
- memset(txdp, 0, sizeof(TxD_t));
+ memset(txdp, 0, sizeof(TxD_t) *
+ config->max_txds);
continue;
}
+ frg_cnt = skb_shinfo(skb)->nr_frags;
+ pci_unmap_single(nic->pdev, (dma_addr_t)
+ txdp->Buffer_Pointer,
+ skb->len - skb->data_len,
+ PCI_DMA_TODEVICE);
+ if (frg_cnt) {
+ TxD_t *temp;
+ temp = txdp;
+ txdp++;
+ for (j = 0; j < frg_cnt; j++, txdp++) {
+ skb_frag_t *frag =
+ &skb_shinfo(skb)->frags[j];
+ pci_unmap_page(nic->pdev,
+ (dma_addr_t)
+ txdp->
+ Buffer_Pointer,
+ frag->size,
+ PCI_DMA_TODEVICE);
+ }
+ txdp = temp;
+ }
dev_kfree_skb(skb);
- memset(txdp, 0, sizeof(TxD_t));
+ memset(txdp, 0, sizeof(TxD_t) * config->max_txds);
cnt++;
}
DBG_PRINT(INTR_DBG,
"%s:forcibly freeing %d skbs on FIFO%d\n",
dev->name, cnt, i);
- mac_control->tx_curr_get_info[i].offset = 0;
- mac_control->tx_curr_put_info[i].offset = 0;
+ mac_control->fifos[i].tx_curr_get_info.offset = 0;
+ mac_control->fifos[i].tx_curr_put_info.offset = 0;
}
}
-/**
- * stop_nic - To stop the nic
+/**
+ * stop_nic - To stop the nic
* @nic ; device private variable.
- * Description:
- * This function does exactly the opposite of what the start_nic()
+ * Description:
+ * This function does exactly the opposite of what the start_nic()
* function does. This function is called to stop the device.
* Return Value:
* void.
@@ -1509,8 +2034,9 @@
config = &nic->config;
/* Disable all interrupts */
- interruptible = TX_TRAFFIC_INTR | RX_TRAFFIC_INTR | TX_MAC_INTR |
- RX_MAC_INTR;
+ interruptible = TX_TRAFFIC_INTR | RX_TRAFFIC_INTR;
+ interruptible |= TX_PIC_INTR | RX_PIC_INTR;
+ interruptible |= TX_MAC_INTR | RX_MAC_INTR;
en_dis_able_nic_intrs(nic, interruptible, DISABLE_INTRS);
/* Disable PRCs */
@@ -1521,11 +2047,11 @@
}
}
-/**
- * fill_rx_buffers - Allocates the Rx side skbs
+/**
+ * fill_rx_buffers - Allocates the Rx side skbs
* @nic: device private variable
- * @ring_no: ring number
- * Description:
+ * @ring_no: ring number
+ * Description:
* The function allocates Rx side skbs and puts the physical
* address of these buffers into the RxD buffer pointers, so that the NIC
* can DMA the received frame into these locations.
@@ -1533,8 +2059,8 @@
* 1. single buffer,
* 2. three buffer and
* 3. Five buffer modes.
- * Each mode defines how many fragments the received frame will be split
- * up into by the NIC. The frame is split into L3 header, L4 Header,
+ * Each mode defines how many fragments the received frame will be split
+ * up into by the NIC. The frame is split into L3 header, L4 Header,
* L4 payload in three buffer mode and in 5 buffer mode, L4 payload itself
* is split into 3 fragments. As of now only single buffer mode is
* supported.
@@ -1542,7 +2068,7 @@
* SUCCESS on success or an appropriate -ve value on failure.
*/
-static int fill_rx_buffers(struct s2io_nic *nic, int ring_no)
+int fill_rx_buffers(struct s2io_nic *nic, int ring_no)
{
struct net_device *dev = nic->dev;
struct sk_buff *skb;
@@ -1550,34 +2076,35 @@
int off, off1, size, block_no, block_no1;
int offset, offset1;
u32 alloc_tab = 0;
- u32 alloc_cnt = nic->pkt_cnt[ring_no] -
- atomic_read(&nic->rx_bufs_left[ring_no]);
+ u32 alloc_cnt;
mac_info_t *mac_control;
struct config_param *config;
#ifdef CONFIG_2BUFF_MODE
RxD_t *rxdpnext;
int nextblk;
- unsigned long tmp;
+ u64 tmp;
buffAdd_t *ba;
dma_addr_t rxdpphys;
#endif
#ifndef CONFIG_S2IO_NAPI
unsigned long flags;
#endif
+ RxD_t *first_rxdp = NULL;
mac_control = &nic->mac_control;
config = &nic->config;
-
+ alloc_cnt = mac_control->rings[ring_no].pkt_cnt -
+ atomic_read(&nic->rx_bufs_left[ring_no]);
size = dev->mtu + HEADER_ETHERNET_II_802_3_SIZE +
HEADER_802_2_SIZE + HEADER_SNAP_SIZE;
while (alloc_tab < alloc_cnt) {
- block_no = mac_control->rx_curr_put_info[ring_no].
+ block_no = mac_control->rings[ring_no].rx_curr_put_info.
block_index;
- block_no1 = mac_control->rx_curr_get_info[ring_no].
+ block_no1 = mac_control->rings[ring_no].rx_curr_get_info.
block_index;
- off = mac_control->rx_curr_put_info[ring_no].offset;
- off1 = mac_control->rx_curr_get_info[ring_no].offset;
+ off = mac_control->rings[ring_no].rx_curr_put_info.offset;
+ off1 = mac_control->rings[ring_no].rx_curr_get_info.offset;
#ifndef CONFIG_2BUFF_MODE
offset = block_no * (MAX_RXDS_PER_BLOCK + 1) + off;
offset1 = block_no1 * (MAX_RXDS_PER_BLOCK + 1) + off1;
@@ -1586,7 +2113,7 @@
offset1 = block_no1 * (MAX_RXDS_PER_BLOCK) + off1;
#endif
- rxdp = nic->rx_blocks[ring_no][block_no].
+ rxdp = mac_control->rings[ring_no].rx_blocks[block_no].
block_virt_addr + off;
if ((offset == offset1) && (rxdp->Host_Control)) {
DBG_PRINT(INTR_DBG, "%s: Get and Put", dev->name);
@@ -1595,15 +2122,15 @@
}
#ifndef CONFIG_2BUFF_MODE
if (rxdp->Control_1 == END_OF_BLOCK) {
- mac_control->rx_curr_put_info[ring_no].
+ mac_control->rings[ring_no].rx_curr_put_info.
block_index++;
- mac_control->rx_curr_put_info[ring_no].
- block_index %= nic->block_count[ring_no];
- block_no = mac_control->rx_curr_put_info
- [ring_no].block_index;
+ mac_control->rings[ring_no].rx_curr_put_info.
+ block_index %= mac_control->rings[ring_no].block_count;
+ block_no = mac_control->rings[ring_no].rx_curr_put_info.
+ block_index;
off++;
off %= (MAX_RXDS_PER_BLOCK + 1);
- mac_control->rx_curr_put_info[ring_no].offset =
+ mac_control->rings[ring_no].rx_curr_put_info.offset =
off;
rxdp = (RxD_t *) ((unsigned long) rxdp->Control_2);
DBG_PRINT(INTR_DBG, "%s: Next block at: %p\n",
@@ -1611,30 +2138,30 @@
}
#ifndef CONFIG_S2IO_NAPI
spin_lock_irqsave(&nic->put_lock, flags);
- nic->put_pos[ring_no] =
+ mac_control->rings[ring_no].put_pos =
(block_no * (MAX_RXDS_PER_BLOCK + 1)) + off;
spin_unlock_irqrestore(&nic->put_lock, flags);
#endif
#else
if (rxdp->Host_Control == END_OF_BLOCK) {
- mac_control->rx_curr_put_info[ring_no].
+ mac_control->rings[ring_no].rx_curr_put_info.
block_index++;
- mac_control->rx_curr_put_info[ring_no].
- block_index %= nic->block_count[ring_no];
- block_no = mac_control->rx_curr_put_info
- [ring_no].block_index;
+ mac_control->rings[ring_no].rx_curr_put_info.block_index
+ %= mac_control->rings[ring_no].block_count;
+ block_no = mac_control->rings[ring_no].rx_curr_put_info
+ .block_index;
off = 0;
DBG_PRINT(INTR_DBG, "%s: block%d at: 0x%llx\n",
dev->name, block_no,
(unsigned long long) rxdp->Control_1);
- mac_control->rx_curr_put_info[ring_no].offset =
+ mac_control->rings[ring_no].rx_curr_put_info.offset =
off;
- rxdp = nic->rx_blocks[ring_no][block_no].
+ rxdp = mac_control->rings[ring_no].rx_blocks[block_no].
block_virt_addr;
}
#ifndef CONFIG_S2IO_NAPI
spin_lock_irqsave(&nic->put_lock, flags);
- nic->put_pos[ring_no] = (block_no *
+ mac_control->rings[ring_no].put_pos = (block_no *
(MAX_RXDS_PER_BLOCK + 1)) + off;
spin_unlock_irqrestore(&nic->put_lock, flags);
#endif
@@ -1646,27 +2173,27 @@
if (rxdp->Control_2 & BIT(0))
#endif
{
- mac_control->rx_curr_put_info[ring_no].
+ mac_control->rings[ring_no].rx_curr_put_info.
offset = off;
goto end;
}
#ifdef CONFIG_2BUFF_MODE
- /*
- * RxDs Spanning cache lines will be replenished only
- * if the succeeding RxD is also owned by Host. It
- * will always be the ((8*i)+3) and ((8*i)+6)
- * descriptors for the 48 byte descriptor. The offending
+ /*
+ * RxDs Spanning cache lines will be replenished only
+ * if the succeeding RxD is also owned by Host. It
+ * will always be the ((8*i)+3) and ((8*i)+6)
+ * descriptors for the 48 byte descriptor. The offending
* decsriptor is of-course the 3rd descriptor.
*/
- rxdpphys = nic->rx_blocks[ring_no][block_no].
+ rxdpphys = mac_control->rings[ring_no].rx_blocks[block_no].
block_dma_addr + (off * sizeof(RxD_t));
if (((u64) (rxdpphys)) % 128 > 80) {
- rxdpnext = nic->rx_blocks[ring_no][block_no].
+ rxdpnext = mac_control->rings[ring_no].rx_blocks[block_no].
block_virt_addr + (off + 1);
if (rxdpnext->Host_Control == END_OF_BLOCK) {
nextblk = (block_no + 1) %
- (nic->block_count[ring_no]);
- rxdpnext = nic->rx_blocks[ring_no]
+ (mac_control->rings[ring_no].block_count);
+ rxdpnext = mac_control->rings[ring_no].rx_blocks
[nextblk].block_virt_addr;
}
if (rxdpnext->Control_2 & BIT(0))
@@ -1682,6 +2209,10 @@
if (!skb) {
DBG_PRINT(ERR_DBG, "%s: Out of ", dev->name);
DBG_PRINT(ERR_DBG, "memory to allocate SKBs\n");
+ if (first_rxdp) {
+ wmb();
+ first_rxdp->Control_1 |= RXD_OWN_XENA;
+ }
return -ENOMEM;
}
#ifndef CONFIG_2BUFF_MODE
@@ -1692,12 +2223,13 @@
rxdp->Control_2 &= (~MASK_BUFFER0_SIZE);
rxdp->Control_2 |= SET_BUFFER0_SIZE(size);
rxdp->Host_Control = (unsigned long) (skb);
- rxdp->Control_1 |= RXD_OWN_XENA;
+ if (alloc_tab & ((1 << rxsync_frequency) - 1))
+ rxdp->Control_1 |= RXD_OWN_XENA;
off++;
off %= (MAX_RXDS_PER_BLOCK + 1);
- mac_control->rx_curr_put_info[ring_no].offset = off;
+ mac_control->rings[ring_no].rx_curr_put_info.offset = off;
#else
- ba = &nic->ba[ring_no][block_no][off];
+ ba = &mac_control->rings[ring_no].ba[block_no][off];
skb_reserve(skb, BUF0_LEN);
tmp = ((unsigned long) skb->data & ALIGN_SIZE);
if (tmp)
@@ -1719,22 +2251,41 @@
rxdp->Control_2 |= SET_BUFFER1_SIZE(1); /* dummy. */
rxdp->Control_2 |= BIT(0); /* Set Buffer_Empty bit. */
rxdp->Host_Control = (u64) ((unsigned long) (skb));
- rxdp->Control_1 |= RXD_OWN_XENA;
+ if (alloc_tab & ((1 << rxsync_frequency) - 1))
+ rxdp->Control_1 |= RXD_OWN_XENA;
off++;
- mac_control->rx_curr_put_info[ring_no].offset = off;
+ mac_control->rings[ring_no].rx_curr_put_info.offset = off;
#endif
+ rxdp->Control_2 |= SET_RXD_MARKER;
+
+ if (!(alloc_tab & ((1 << rxsync_frequency) - 1))) {
+ if (first_rxdp) {
+ wmb();
+ first_rxdp->Control_1 |= RXD_OWN_XENA;
+ }
+ first_rxdp = rxdp;
+ }
atomic_inc(&nic->rx_bufs_left[ring_no]);
alloc_tab++;
}
end:
+ /* Transfer ownership of first descriptor to adapter just before
+ * exiting. Before that, use memory barrier so that ownership
+ * and other fields are seen by adapter correctly.
+ */
+ if (first_rxdp) {
+ wmb();
+ first_rxdp->Control_1 |= RXD_OWN_XENA;
+ }
+
return SUCCESS;
}
/**
- * free_rx_buffers - Frees all Rx buffers
+ * free_rx_buffers - Frees all Rx buffers
* @sp: device private variable.
- * Description:
+ * Description:
* This function will free all Rx buffers allocated by host.
* Return Value:
* NONE.
@@ -1758,7 +2309,8 @@
for (i = 0; i < config->rx_ring_num; i++) {
for (j = 0, blk = 0; j < config->rx_cfg[i].num_rxd; j++) {
off = j % (MAX_RXDS_PER_BLOCK + 1);
- rxdp = sp->rx_blocks[i][blk].block_virt_addr + off;
+ rxdp = mac_control->rings[i].rx_blocks[blk].
+ block_virt_addr + off;
#ifndef CONFIG_2BUFF_MODE
if (rxdp->Control_1 == END_OF_BLOCK) {
@@ -1793,7 +2345,7 @@
HEADER_SNAP_SIZE,
PCI_DMA_FROMDEVICE);
#else
- ba = &sp->ba[i][blk][off];
+ ba = &mac_control->rings[i].ba[blk][off];
pci_unmap_single(sp->pdev, (dma_addr_t)
rxdp->Buffer0_ptr,
BUF0_LEN,
@@ -1813,10 +2365,10 @@
}
memset(rxdp, 0, sizeof(RxD_t));
}
- mac_control->rx_curr_put_info[i].block_index = 0;
- mac_control->rx_curr_get_info[i].block_index = 0;
- mac_control->rx_curr_put_info[i].offset = 0;
- mac_control->rx_curr_get_info[i].offset = 0;
+ mac_control->rings[i].rx_curr_put_info.block_index = 0;
+ mac_control->rings[i].rx_curr_get_info.block_index = 0;
+ mac_control->rings[i].rx_curr_put_info.offset = 0;
+ mac_control->rings[i].rx_curr_get_info.offset = 0;
atomic_set(&sp->rx_bufs_left[i], 0);
DBG_PRINT(INIT_DBG, "%s:Freed 0x%x Rx Buffers on ring%d\n",
dev->name, buf_cnt, i);
@@ -1826,7 +2378,7 @@
/**
* s2io_poll - Rx interrupt handler for NAPI support
* @dev : pointer to the device structure.
- * @budget : The number of packets that were budgeted to be processed
+ * @budget : The number of packets that were budgeted to be processed
* during one pass through the 'Poll" function.
* Description:
* Comes into picture only if NAPI support has been incorporated. It does
@@ -1836,160 +2388,36 @@
* 0 on success and 1 if there are No Rx packets to be processed.
*/
-#ifdef CONFIG_S2IO_NAPI
+#if defined(CONFIG_S2IO_NAPI)
static int s2io_poll(struct net_device *dev, int *budget)
{
nic_t *nic = dev->priv;
- XENA_dev_config_t __iomem *bar0 = nic->bar0;
- int pkts_to_process = *budget, pkt_cnt = 0;
- register u64 val64 = 0;
- rx_curr_get_info_t get_info, put_info;
- int i, get_block, put_block, get_offset, put_offset, ring_bufs;
-#ifndef CONFIG_2BUFF_MODE
- u16 val16, cksum;
-#endif
- struct sk_buff *skb;
- RxD_t *rxdp;
+ int pkt_cnt = 0, org_pkts_to_process;
mac_info_t *mac_control;
struct config_param *config;
-#ifdef CONFIG_2BUFF_MODE
- buffAdd_t *ba;
-#endif
+ XENA_dev_config_t *bar0 = (XENA_dev_config_t *) nic->bar0;
+ u64 val64;
+ int i;
+ atomic_inc(&nic->isr_cnt);
mac_control = &nic->mac_control;
config = &nic->config;
- if (pkts_to_process > dev->quota)
- pkts_to_process = dev->quota;
+ nic->pkts_to_process = *budget;
+ if (nic->pkts_to_process > dev->quota)
+ nic->pkts_to_process = dev->quota;
+ org_pkts_to_process = nic->pkts_to_process;
val64 = readq(&bar0->rx_traffic_int);
writeq(val64, &bar0->rx_traffic_int);
for (i = 0; i < config->rx_ring_num; i++) {
- get_info = mac_control->rx_curr_get_info[i];
- get_block = get_info.block_index;
- put_info = mac_control->rx_curr_put_info[i];
- put_block = put_info.block_index;
- ring_bufs = config->rx_cfg[i].num_rxd;
- rxdp = nic->rx_blocks[i][get_block].block_virt_addr +
- get_info.offset;
-#ifndef CONFIG_2BUFF_MODE
- get_offset = (get_block * (MAX_RXDS_PER_BLOCK + 1)) +
- get_info.offset;
- put_offset = (put_block * (MAX_RXDS_PER_BLOCK + 1)) +
- put_info.offset;
- while ((!(rxdp->Control_1 & RXD_OWN_XENA)) &&
- (((get_offset + 1) % ring_bufs) != put_offset)) {
- if (--pkts_to_process < 0) {
- goto no_rx;
- }
- if (rxdp->Control_1 == END_OF_BLOCK) {
- rxdp =
- (RxD_t *) ((unsigned long) rxdp->
- Control_2);
- get_info.offset++;
- get_info.offset %=
- (MAX_RXDS_PER_BLOCK + 1);
- get_block++;
- get_block %= nic->block_count[i];
- mac_control->rx_curr_get_info[i].
- offset = get_info.offset;
- mac_control->rx_curr_get_info[i].
- block_index = get_block;
- continue;
- }
- get_offset =
- (get_block * (MAX_RXDS_PER_BLOCK + 1)) +
- get_info.offset;
- skb =
- (struct sk_buff *) ((unsigned long) rxdp->
- Host_Control);
- if (skb == NULL) {
- DBG_PRINT(ERR_DBG, "%s: The skb is ",
- dev->name);
- DBG_PRINT(ERR_DBG, "Null in Rx Intr\n");
- goto no_rx;
- }
- val64 = RXD_GET_BUFFER0_SIZE(rxdp->Control_2);
- val16 = (u16) (val64 >> 48);
- cksum = RXD_GET_L4_CKSUM(rxdp->Control_1);
- pci_unmap_single(nic->pdev, (dma_addr_t)
- rxdp->Buffer0_ptr,
- dev->mtu +
- HEADER_ETHERNET_II_802_3_SIZE +
- HEADER_802_2_SIZE +
- HEADER_SNAP_SIZE,
- PCI_DMA_FROMDEVICE);
- rx_osm_handler(nic, val16, rxdp, i);
- pkt_cnt++;
- get_info.offset++;
- get_info.offset %= (MAX_RXDS_PER_BLOCK + 1);
- rxdp =
- nic->rx_blocks[i][get_block].block_virt_addr +
- get_info.offset;
- mac_control->rx_curr_get_info[i].offset =
- get_info.offset;
+ rx_intr_handler(&mac_control->rings[i]);
+ pkt_cnt = org_pkts_to_process - nic->pkts_to_process;
+ if (!nic->pkts_to_process) {
+ /* Quota for the current iteration has been met */
+ goto no_rx;
}
-#else
- get_offset = (get_block * (MAX_RXDS_PER_BLOCK + 1)) +
- get_info.offset;
- put_offset = (put_block * (MAX_RXDS_PER_BLOCK + 1)) +
- put_info.offset;
- while (((!(rxdp->Control_1 & RXD_OWN_XENA)) &&
- !(rxdp->Control_2 & BIT(0))) &&
- (((get_offset + 1) % ring_bufs) != put_offset)) {
- if (--pkts_to_process < 0) {
- goto no_rx;
- }
- skb = (struct sk_buff *) ((unsigned long)
- rxdp->Host_Control);
- if (skb == NULL) {
- DBG_PRINT(ERR_DBG, "%s: The skb is ",
- dev->name);
- DBG_PRINT(ERR_DBG, "Null in Rx Intr\n");
- goto no_rx;
- }
-
- pci_unmap_single(nic->pdev, (dma_addr_t)
- rxdp->Buffer0_ptr,
- BUF0_LEN, PCI_DMA_FROMDEVICE);
- pci_unmap_single(nic->pdev, (dma_addr_t)
- rxdp->Buffer1_ptr,
- BUF1_LEN, PCI_DMA_FROMDEVICE);
- pci_unmap_single(nic->pdev, (dma_addr_t)
- rxdp->Buffer2_ptr,
- dev->mtu + BUF0_LEN + 4,
- PCI_DMA_FROMDEVICE);
- ba = &nic->ba[i][get_block][get_info.offset];
-
- rx_osm_handler(nic, rxdp, i, ba);
-
- get_info.offset++;
- mac_control->rx_curr_get_info[i].offset =
- get_info.offset;
- rxdp =
- nic->rx_blocks[i][get_block].block_virt_addr +
- get_info.offset;
-
- if (get_info.offset &&
- (!(get_info.offset % MAX_RXDS_PER_BLOCK))) {
- get_info.offset = 0;
- mac_control->rx_curr_get_info[i].
- offset = get_info.offset;
- get_block++;
- get_block %= nic->block_count[i];
- mac_control->rx_curr_get_info[i].
- block_index = get_block;
- rxdp =
- nic->rx_blocks[i][get_block].
- block_virt_addr;
- }
- get_offset =
- (get_block * (MAX_RXDS_PER_BLOCK + 1)) +
- get_info.offset;
- pkt_cnt++;
- }
-#endif
}
if (!pkt_cnt)
pkt_cnt = 1;
@@ -2007,9 +2435,10 @@
}
/* Re enable the Rx interrupts. */
en_dis_able_nic_intrs(nic, RX_TRAFFIC_INTR, ENABLE_INTRS);
+ atomic_dec(&nic->isr_cnt);
return 0;
- no_rx:
+no_rx:
dev->quota -= pkt_cnt;
*budget -= pkt_cnt;
@@ -2020,279 +2449,204 @@
break;
}
}
+ atomic_dec(&nic->isr_cnt);
return 1;
}
-#else
-/**
+#endif
+
+/**
* rx_intr_handler - Rx interrupt handler
* @nic: device private variable.
- * Description:
- * If the interrupt is because of a received frame or if the
+ * Description:
+ * If the interrupt is because of a received frame or if the
* receive ring contains fresh as yet un-processed frames,this function is
- * called. It picks out the RxD at which place the last Rx processing had
- * stopped and sends the skb to the OSM's Rx handler and then increments
+ * called. It picks out the RxD at which place the last Rx processing had
+ * stopped and sends the skb to the OSM's Rx handler and then increments
* the offset.
* Return Value:
* NONE.
*/
-
-static void rx_intr_handler(struct s2io_nic *nic)
+static void rx_intr_handler(ring_info_t *ring_data)
{
+ nic_t *nic = ring_data->nic;
struct net_device *dev = (struct net_device *) nic->dev;
- XENA_dev_config_t *bar0 = (XENA_dev_config_t *) nic->bar0;
+ int get_block, get_offset, put_block, put_offset, ring_bufs;
rx_curr_get_info_t get_info, put_info;
RxD_t *rxdp;
struct sk_buff *skb;
-#ifndef CONFIG_2BUFF_MODE
- u16 val16, cksum;
+#ifndef CONFIG_S2IO_NAPI
+ int pkt_cnt = 0;
#endif
- register u64 val64 = 0;
- int get_block, get_offset, put_block, put_offset, ring_bufs;
- int i, pkt_cnt = 0;
- mac_info_t *mac_control;
- struct config_param *config;
-#ifdef CONFIG_2BUFF_MODE
- buffAdd_t *ba;
-#endif
+ spin_lock(&nic->rx_lock);
+ if (atomic_read(&nic->card_state) == CARD_DOWN) {
+ DBG_PRINT(ERR_DBG, "%s: %s going down for reset\n",
+ __FUNCTION__, dev->name);
+ spin_unlock(&nic->rx_lock);
+ }
- mac_control = &nic->mac_control;
- config = &nic->config;
-
- /*
- * rx_traffic_int reg is an R1 register, hence we read and write back
- * the samevalue in the register to clear it.
- */
- val64 = readq(&bar0->rx_traffic_int);
- writeq(val64, &bar0->rx_traffic_int);
-
- for (i = 0; i < config->rx_ring_num; i++) {
- get_info = mac_control->rx_curr_get_info[i];
- get_block = get_info.block_index;
- put_info = mac_control->rx_curr_put_info[i];
- put_block = put_info.block_index;
- ring_bufs = config->rx_cfg[i].num_rxd;
- rxdp = nic->rx_blocks[i][get_block].block_virt_addr +
+ get_info = ring_data->rx_curr_get_info;
+ get_block = get_info.block_index;
+ put_info = ring_data->rx_curr_put_info;
+ put_block = put_info.block_index;
+ ring_bufs = get_info.ring_len+1;
+ rxdp = ring_data->rx_blocks[get_block].block_virt_addr +
get_info.offset;
-#ifndef CONFIG_2BUFF_MODE
- get_offset = (get_block * (MAX_RXDS_PER_BLOCK + 1)) +
- get_info.offset;
- spin_lock(&nic->put_lock);
- put_offset = nic->put_pos[i];
- spin_unlock(&nic->put_lock);
- while ((!(rxdp->Control_1 & RXD_OWN_XENA)) &&
- (((get_offset + 1) % ring_bufs) != put_offset)) {
- if (rxdp->Control_1 == END_OF_BLOCK) {
- rxdp = (RxD_t *) ((unsigned long)
- rxdp->Control_2);
- get_info.offset++;
- get_info.offset %=
- (MAX_RXDS_PER_BLOCK + 1);
- get_block++;
- get_block %= nic->block_count[i];
- mac_control->rx_curr_get_info[i].
- offset = get_info.offset;
- mac_control->rx_curr_get_info[i].
- block_index = get_block;
- continue;
- }
- get_offset =
- (get_block * (MAX_RXDS_PER_BLOCK + 1)) +
- get_info.offset;
- skb = (struct sk_buff *) ((unsigned long)
- rxdp->Host_Control);
- if (skb == NULL) {
- DBG_PRINT(ERR_DBG, "%s: The skb is ",
- dev->name);
- DBG_PRINT(ERR_DBG, "Null in Rx Intr\n");
- return;
- }
- val64 = RXD_GET_BUFFER0_SIZE(rxdp->Control_2);
- val16 = (u16) (val64 >> 48);
- cksum = RXD_GET_L4_CKSUM(rxdp->Control_1);
- pci_unmap_single(nic->pdev, (dma_addr_t)
- rxdp->Buffer0_ptr,
- dev->mtu +
- HEADER_ETHERNET_II_802_3_SIZE +
- HEADER_802_2_SIZE +
- HEADER_SNAP_SIZE,
- PCI_DMA_FROMDEVICE);
- rx_osm_handler(nic, val16, rxdp, i);
- get_info.offset++;
- get_info.offset %= (MAX_RXDS_PER_BLOCK + 1);
- rxdp =
- nic->rx_blocks[i][get_block].block_virt_addr +
- get_info.offset;
- mac_control->rx_curr_get_info[i].offset =
- get_info.offset;
- pkt_cnt++;
- if ((indicate_max_pkts)
- && (pkt_cnt > indicate_max_pkts))
- break;
- }
+ get_offset = (get_block * (MAX_RXDS_PER_BLOCK + 1)) +
+ get_info.offset;
+#ifndef CONFIG_S2IO_NAPI
+ spin_lock(&nic->put_lock);
+ put_offset = ring_data->put_pos;
+ spin_unlock(&nic->put_lock);
#else
- get_offset = (get_block * (MAX_RXDS_PER_BLOCK + 1)) +
- get_info.offset;
- spin_lock(&nic->put_lock);
- put_offset = nic->put_pos[i];
- spin_unlock(&nic->put_lock);
- while (((!(rxdp->Control_1 & RXD_OWN_XENA)) &&
- !(rxdp->Control_2 & BIT(0))) &&
- (((get_offset + 1) % ring_bufs) != put_offset)) {
- skb = (struct sk_buff *) ((unsigned long)
- rxdp->Host_Control);
- if (skb == NULL) {
- DBG_PRINT(ERR_DBG, "%s: The skb is ",
- dev->name);
- DBG_PRINT(ERR_DBG, "Null in Rx Intr\n");
- return;
- }
-
- pci_unmap_single(nic->pdev, (dma_addr_t)
- rxdp->Buffer0_ptr,
- BUF0_LEN, PCI_DMA_FROMDEVICE);
- pci_unmap_single(nic->pdev, (dma_addr_t)
- rxdp->Buffer1_ptr,
- BUF1_LEN, PCI_DMA_FROMDEVICE);
- pci_unmap_single(nic->pdev, (dma_addr_t)
- rxdp->Buffer2_ptr,
- dev->mtu + BUF0_LEN + 4,
- PCI_DMA_FROMDEVICE);
- ba = &nic->ba[i][get_block][get_info.offset];
-
- rx_osm_handler(nic, rxdp, i, ba);
-
- get_info.offset++;
- mac_control->rx_curr_get_info[i].offset =
- get_info.offset;
- rxdp =
- nic->rx_blocks[i][get_block].block_virt_addr +
- get_info.offset;
-
- if (get_info.offset &&
- (!(get_info.offset % MAX_RXDS_PER_BLOCK))) {
- get_info.offset = 0;
- mac_control->rx_curr_get_info[i].
- offset = get_info.offset;
- get_block++;
- get_block %= nic->block_count[i];
- mac_control->rx_curr_get_info[i].
- block_index = get_block;
- rxdp =
- nic->rx_blocks[i][get_block].
- block_virt_addr;
- }
- get_offset =
- (get_block * (MAX_RXDS_PER_BLOCK + 1)) +
- get_info.offset;
- pkt_cnt++;
- if ((indicate_max_pkts)
- && (pkt_cnt > indicate_max_pkts))
- break;
- }
+ put_offset = (put_block * (MAX_RXDS_PER_BLOCK + 1)) +
+ put_info.offset;
#endif
+ while (RXD_IS_UP2DT(rxdp) &&
+ (((get_offset + 1) % ring_bufs) != put_offset)) {
+ skb = (struct sk_buff *) ((unsigned long)rxdp->Host_Control);
+ if (skb == NULL) {
+ DBG_PRINT(ERR_DBG, "%s: The skb is ",
+ dev->name);
+ DBG_PRINT(ERR_DBG, "Null in Rx Intr\n");
+ spin_unlock(&nic->rx_lock);
+ return;
+ }
+#ifndef CONFIG_2BUFF_MODE
+ pci_unmap_single(nic->pdev, (dma_addr_t)
+ rxdp->Buffer0_ptr,
+ dev->mtu +
+ HEADER_ETHERNET_II_802_3_SIZE +
+ HEADER_802_2_SIZE +
+ HEADER_SNAP_SIZE,
+ PCI_DMA_FROMDEVICE);
+#else
+ pci_unmap_single(nic->pdev, (dma_addr_t)
+ rxdp->Buffer0_ptr,
+ BUF0_LEN, PCI_DMA_FROMDEVICE);
+ pci_unmap_single(nic->pdev, (dma_addr_t)
+ rxdp->Buffer1_ptr,
+ BUF1_LEN, PCI_DMA_FROMDEVICE);
+ pci_unmap_single(nic->pdev, (dma_addr_t)
+ rxdp->Buffer2_ptr,
+ dev->mtu + BUF0_LEN + 4,
+ PCI_DMA_FROMDEVICE);
+#endif
+ rx_osm_handler(ring_data, rxdp);
+ get_info.offset++;
+ ring_data->rx_curr_get_info.offset =
+ get_info.offset;
+ rxdp = ring_data->rx_blocks[get_block].block_virt_addr +
+ get_info.offset;
+ if (get_info.offset &&
+ (!(get_info.offset % MAX_RXDS_PER_BLOCK))) {
+ get_info.offset = 0;
+ ring_data->rx_curr_get_info.offset
+ = get_info.offset;
+ get_block++;
+ get_block %= ring_data->block_count;
+ ring_data->rx_curr_get_info.block_index
+ = get_block;
+ rxdp = ring_data->rx_blocks[get_block].block_virt_addr;
+ }
+
+ get_offset = (get_block * (MAX_RXDS_PER_BLOCK + 1)) +
+ get_info.offset;
+#ifdef CONFIG_S2IO_NAPI
+ nic->pkts_to_process -= 1;
+ if (!nic->pkts_to_process)
+ break;
+#else
+ pkt_cnt++;
if ((indicate_max_pkts) && (pkt_cnt > indicate_max_pkts))
break;
- }
-}
#endif
-/**
+ }
+ spin_unlock(&nic->rx_lock);
+}
+
+/**
* tx_intr_handler - Transmit interrupt handler
* @nic : device private variable
- * Description:
- * If an interrupt was raised to indicate DMA complete of the
- * Tx packet, this function is called. It identifies the last TxD
- * whose buffer was freed and frees all skbs whose data have already
+ * Description:
+ * If an interrupt was raised to indicate DMA complete of the
+ * Tx packet, this function is called. It identifies the last TxD
+ * whose buffer was freed and frees all skbs whose data have already
* DMA'ed into the NICs internal memory.
* Return Value:
* NONE
*/
-static void tx_intr_handler(struct s2io_nic *nic)
+static void tx_intr_handler(fifo_info_t *fifo_data)
{
- XENA_dev_config_t __iomem *bar0 = nic->bar0;
+ nic_t *nic = fifo_data->nic;
struct net_device *dev = (struct net_device *) nic->dev;
tx_curr_get_info_t get_info, put_info;
struct sk_buff *skb;
TxD_t *txdlp;
- register u64 val64 = 0;
- int i;
u16 j, frg_cnt;
- mac_info_t *mac_control;
- struct config_param *config;
- mac_control = &nic->mac_control;
- config = &nic->config;
-
- /*
- * tx_traffic_int reg is an R1 register, hence we read and write
- * back the samevalue in the register to clear it.
- */
- val64 = readq(&bar0->tx_traffic_int);
- writeq(val64, &bar0->tx_traffic_int);
-
- for (i = 0; i < config->tx_fifo_num; i++) {
- get_info = mac_control->tx_curr_get_info[i];
- put_info = mac_control->tx_curr_put_info[i];
- txdlp = (TxD_t *) nic->list_info[i][get_info.offset].
- list_virt_addr;
- while ((!(txdlp->Control_1 & TXD_LIST_OWN_XENA)) &&
- (get_info.offset != put_info.offset) &&
- (txdlp->Host_Control)) {
- /* Check for TxD errors */
- if (txdlp->Control_1 & TXD_T_CODE) {
- unsigned long long err;
- err = txdlp->Control_1 & TXD_T_CODE;
- DBG_PRINT(ERR_DBG, "***TxD error %llx\n",
- err);
- }
-
- skb = (struct sk_buff *) ((unsigned long)
- txdlp->Host_Control);
- if (skb == NULL) {
- DBG_PRINT(ERR_DBG, "%s: Null skb ",
- dev->name);
- DBG_PRINT(ERR_DBG, "in Tx Free Intr\n");
- return;
- }
- nic->tx_pkt_count++;
-
- frg_cnt = skb_shinfo(skb)->nr_frags;
-
- /* For unfragmented skb */
- pci_unmap_single(nic->pdev, (dma_addr_t)
- txdlp->Buffer_Pointer,
- skb->len - skb->data_len,
- PCI_DMA_TODEVICE);
- if (frg_cnt) {
- TxD_t *temp = txdlp;
- txdlp++;
- for (j = 0; j < frg_cnt; j++, txdlp++) {
- skb_frag_t *frag =
- &skb_shinfo(skb)->frags[j];
- pci_unmap_page(nic->pdev,
- (dma_addr_t)
- txdlp->
- Buffer_Pointer,
- frag->size,
- PCI_DMA_TODEVICE);
- }
- txdlp = temp;
- }
- memset(txdlp, 0,
- (sizeof(TxD_t) * config->max_txds));
-
- /* Updating the statistics block */
- nic->stats.tx_packets++;
- nic->stats.tx_bytes += skb->len;
- dev_kfree_skb_irq(skb);
-
- get_info.offset++;
- get_info.offset %= get_info.fifo_len + 1;
- txdlp = (TxD_t *) nic->list_info[i]
- [get_info.offset].list_virt_addr;
- mac_control->tx_curr_get_info[i].offset =
- get_info.offset;
+ get_info = fifo_data->tx_curr_get_info;
+ put_info = fifo_data->tx_curr_put_info;
+ txdlp = (TxD_t *) fifo_data->list_info[get_info.offset].
+ list_virt_addr;
+ while ((!(txdlp->Control_1 & TXD_LIST_OWN_XENA)) &&
+ (get_info.offset != put_info.offset) &&
+ (txdlp->Host_Control)) {
+ /* Check for TxD errors */
+ if (txdlp->Control_1 & TXD_T_CODE) {
+ unsigned long long err;
+ err = txdlp->Control_1 & TXD_T_CODE;
+ DBG_PRINT(ERR_DBG, "***TxD error %llx\n",
+ err);
}
+
+ skb = (struct sk_buff *) ((unsigned long)
+ txdlp->Host_Control);
+ if (skb == NULL) {
+ DBG_PRINT(ERR_DBG, "%s: Null skb ",
+ __FUNCTION__);
+ DBG_PRINT(ERR_DBG, "in Tx Free Intr\n");
+ return;
+ }
+
+ frg_cnt = skb_shinfo(skb)->nr_frags;
+ nic->tx_pkt_count++;
+
+ pci_unmap_single(nic->pdev, (dma_addr_t)
+ txdlp->Buffer_Pointer,
+ skb->len - skb->data_len,
+ PCI_DMA_TODEVICE);
+ if (frg_cnt) {
+ TxD_t *temp;
+ temp = txdlp;
+ txdlp++;
+ for (j = 0; j < frg_cnt; j++, txdlp++) {
+ skb_frag_t *frag =
+ &skb_shinfo(skb)->frags[j];
+ if (!txdlp->Buffer_Pointer)
+ break;
+ pci_unmap_page(nic->pdev,
+ (dma_addr_t)
+ txdlp->
+ Buffer_Pointer,
+ frag->size,
+ PCI_DMA_TODEVICE);
+ }
+ txdlp = temp;
+ }
+ memset(txdlp, 0,
+ (sizeof(TxD_t) * fifo_data->max_txds));
+
+ /* Updating the statistics block */
+ nic->stats.tx_bytes += skb->len;
+ dev_kfree_skb_irq(skb);
+
+ get_info.offset++;
+ get_info.offset %= get_info.fifo_len + 1;
+ txdlp = (TxD_t *) fifo_data->list_info
+ [get_info.offset].list_virt_addr;
+ fifo_data->tx_curr_get_info.offset =
+ get_info.offset;
}
spin_lock(&nic->tx_lock);
@@ -2301,13 +2655,13 @@
spin_unlock(&nic->tx_lock);
}
-/**
+/**
* alarm_intr_handler - Alarm Interrrupt handler
* @nic: device private variable
- * Description: If the interrupt was neither because of Rx packet or Tx
+ * Description: If the interrupt was neither because of Rx packet or Tx
* complete, this function is called. If the interrupt was to indicate
- * a loss of link, the OSM link status handler is invoked for any other
- * alarm interrupt the block that raised the interrupt is displayed
+ * a loss of link, the OSM link status handler is invoked for any other
+ * alarm interrupt the block that raised the interrupt is displayed
* and a H/W reset is issued.
* Return Value:
* NONE
@@ -2320,10 +2674,32 @@
register u64 val64 = 0, err_reg = 0;
/* Handling link status change error Intr */
- err_reg = readq(&bar0->mac_rmac_err_reg);
- writeq(err_reg, &bar0->mac_rmac_err_reg);
- if (err_reg & RMAC_LINK_STATE_CHANGE_INT) {
- schedule_work(&nic->set_link_task);
+ if (s2io_link_fault_indication(nic) == MAC_RMAC_ERR_TIMER) {
+ err_reg = readq(&bar0->mac_rmac_err_reg);
+ writeq(err_reg, &bar0->mac_rmac_err_reg);
+ if (err_reg & RMAC_LINK_STATE_CHANGE_INT) {
+ schedule_work(&nic->set_link_task);
+ }
+ }
+
+ /* Handling Ecc errors */
+ val64 = readq(&bar0->mc_err_reg);
+ writeq(val64, &bar0->mc_err_reg);
+ if (val64 & (MC_ERR_REG_ECC_ALL_SNG | MC_ERR_REG_ECC_ALL_DBL)) {
+ if (val64 & MC_ERR_REG_ECC_ALL_DBL) {
+ nic->mac_control.stats_info->sw_stat.
+ double_ecc_errs++;
+ DBG_PRINT(ERR_DBG, "%s: Device indicates ",
+ dev->name);
+ DBG_PRINT(ERR_DBG, "double ECC error!!\n");
+ if (nic->device_type != XFRAME_II_DEVICE) {
+ netif_stop_queue(dev);
+ schedule_work(&nic->rst_timer_task);
+ }
+ } else {
+ nic->mac_control.stats_info->sw_stat.
+ single_ecc_errs++;
+ }
}
/* In case of a serious error, the device will be Reset. */
@@ -2338,7 +2714,7 @@
/*
* Also as mentioned in the latest Errata sheets if the PCC_FB_ECC
* Error occurs, the adapter will be recycled by disabling the
- * adapter enable bit and enabling it again after the device
+ * adapter enable bit and enabling it again after the device
* becomes Quiescent.
*/
val64 = readq(&bar0->pcc_err_reg);
@@ -2354,18 +2730,18 @@
/* Other type of interrupts are not being handled now, TODO */
}
-/**
+/**
* wait_for_cmd_complete - waits for a command to complete.
- * @sp : private member of the device structure, which is a pointer to the
+ * @sp : private member of the device structure, which is a pointer to the
* s2io_nic structure.
- * Description: Function that waits for a command to Write into RMAC
- * ADDR DATA registers to be completed and returns either success or
- * error depending on whether the command was complete or not.
+ * Description: Function that waits for a command to Write into RMAC
+ * ADDR DATA registers to be completed and returns either success or
+ * error depending on whether the command was complete or not.
* Return value:
* SUCCESS on success and FAILURE on failure.
*/
-static int wait_for_cmd_complete(nic_t * sp)
+int wait_for_cmd_complete(nic_t * sp)
{
XENA_dev_config_t __iomem *bar0 = sp->bar0;
int ret = FAILURE, cnt = 0;
@@ -2385,29 +2761,32 @@
return ret;
}
-/**
- * s2io_reset - Resets the card.
+/**
+ * s2io_reset - Resets the card.
* @sp : private member of the device structure.
* Description: Function to Reset the card. This function then also
- * restores the previously saved PCI configuration space registers as
+ * restores the previously saved PCI configuration space registers as
* the card reset also resets the configuration space.
* Return value:
* void.
*/
-static void s2io_reset(nic_t * sp)
+void s2io_reset(nic_t * sp)
{
XENA_dev_config_t __iomem *bar0 = sp->bar0;
u64 val64;
- u16 subid;
+ u16 subid, pci_cmd;
+
+ /* Back up the PCI-X CMD reg, dont want to lose MMRBC, OST settings */
+ pci_read_config_word(sp->pdev, PCIX_COMMAND_REGISTER, &(pci_cmd));
val64 = SW_RESET_ALL;
writeq(val64, &bar0->sw_reset);
- /*
- * At this stage, if the PCI write is indeed completed, the
- * card is reset and so is the PCI Config space of the device.
- * So a read cannot be issued at this stage on any of the
+ /*
+ * At this stage, if the PCI write is indeed completed, the
+ * card is reset and so is the PCI Config space of the device.
+ * So a read cannot be issued at this stage on any of the
* registers to ensure the write into "sw_reset" register
* has gone through.
* Question: Is there any system call that will explicitly force
@@ -2418,42 +2797,72 @@
*/
msleep(250);
- /* Restore the PCI state saved during initializarion. */
+ /* Restore the PCI state saved during initialization. */
pci_restore_state(sp->pdev);
+ pci_write_config_word(sp->pdev, PCIX_COMMAND_REGISTER,
+ pci_cmd);
s2io_init_pci(sp);
msleep(250);
+ /* Set swapper to enable I/O register access */
+ s2io_set_swapper(sp);
+
+ /* Clear certain PCI/PCI-X fields after reset */
+ if (sp->device_type == XFRAME_II_DEVICE) {
+ /* Clear parity err detect bit */
+ pci_write_config_word(sp->pdev, PCI_STATUS, 0x8000);
+
+ /* Clearing PCIX Ecc status register */
+ pci_write_config_dword(sp->pdev, 0x68, 0x7C);
+
+ /* Clearing PCI_STATUS error reflected here */
+ writeq(BIT(62), &bar0->txpic_int_reg);
+ }
+
+ /* Reset device statistics maintained by OS */
+ memset(&sp->stats, 0, sizeof (struct net_device_stats));
+
/* SXE-002: Configure link and activity LED to turn it off */
subid = sp->pdev->subsystem_device;
- if ((subid & 0xFF) >= 0x07) {
+ if (((subid & 0xFF) >= 0x07) &&
+ (sp->device_type == XFRAME_I_DEVICE)) {
val64 = readq(&bar0->gpio_control);
val64 |= 0x0000800000000000ULL;
writeq(val64, &bar0->gpio_control);
val64 = 0x0411040400000000ULL;
- writeq(val64, (void __iomem *) bar0 + 0x2700);
+ writeq(val64, (void __iomem *) ((u8 *) bar0 + 0x2700));
+ }
+
+ /*
+ * Clear spurious ECC interrupts that would have occured on
+ * XFRAME II cards after reset.
+ */
+ if (sp->device_type == XFRAME_II_DEVICE) {
+ val64 = readq(&bar0->pcc_err_reg);
+ writeq(val64, &bar0->pcc_err_reg);
}
sp->device_enabled_once = FALSE;
}
/**
- * s2io_set_swapper - to set the swapper controle on the card
- * @sp : private member of the device structure,
+ * s2io_set_swapper - to set the swapper controle on the card
+ * @sp : private member of the device structure,
* pointer to the s2io_nic structure.
- * Description: Function to set the swapper control on the card
+ * Description: Function to set the swapper control on the card
* correctly depending on the 'endianness' of the system.
* Return value:
* SUCCESS on success and FAILURE on failure.
*/
-static int s2io_set_swapper(nic_t * sp)
+int s2io_set_swapper(nic_t * sp)
{
struct net_device *dev = sp->dev;
XENA_dev_config_t __iomem *bar0 = sp->bar0;
u64 val64, valt, valr;
- /*
+ /*
* Set proper endian settings and verify the same by reading
* the PIF Feed-back register.
*/
@@ -2505,8 +2914,9 @@
i++;
}
if(i == 4) {
+ unsigned long long x = val64;
DBG_PRINT(ERR_DBG, "Write failed, Xmsi_addr ");
- DBG_PRINT(ERR_DBG, "reads:0x%llx\n",val64);
+ DBG_PRINT(ERR_DBG, "reads:0x%llx\n", x);
return FAILURE;
}
}
@@ -2514,8 +2924,8 @@
val64 &= 0xFFFF000000000000ULL;
#ifdef __BIG_ENDIAN
- /*
- * The device by default set to a big endian format, so a
+ /*
+ * The device by default set to a big endian format, so a
* big endian driver need not set anything.
*/
val64 |= (SWAPPER_CTRL_TXP_FE |
@@ -2531,9 +2941,9 @@
SWAPPER_CTRL_STATS_FE | SWAPPER_CTRL_STATS_SE);
writeq(val64, &bar0->swapper_ctrl);
#else
- /*
+ /*
* Initially we enable all bits to make it accessible by the
- * driver, then we selectively enable only those bits that
+ * driver, then we selectively enable only those bits that
* we want to set.
*/
val64 |= (SWAPPER_CTRL_TXP_FE |
@@ -2555,8 +2965,8 @@
#endif
val64 = readq(&bar0->swapper_ctrl);
- /*
- * Verifying if endian settings are accurate by reading a
+ /*
+ * Verifying if endian settings are accurate by reading a
* feedback register.
*/
val64 = readq(&bar0->pif_rd_swapper_fb);
@@ -2576,55 +2986,63 @@
* Functions defined below concern the OS part of the driver *
* ********************************************************* */
-/**
+/**
* s2io_open - open entry point of the driver
* @dev : pointer to the device structure.
* Description:
* This function is the open entry point of the driver. It mainly calls a
* function to allocate Rx buffers and inserts them into the buffer
- * descriptors and then enables the Rx part of the NIC.
+ * descriptors and then enables the Rx part of the NIC.
* Return value:
* 0 on success and an appropriate (-)ve integer as defined in errno.h
* file on failure.
*/
-static int s2io_open(struct net_device *dev)
+int s2io_open(struct net_device *dev)
{
nic_t *sp = dev->priv;
int err = 0;
- /*
- * Make sure you have link off by default every time
+ /*
+ * Make sure you have link off by default every time
* Nic is initialized
*/
netif_carrier_off(dev);
- sp->last_link_state = LINK_DOWN;
+ sp->last_link_state = 0;
/* Initialize H/W and enable interrupts */
if (s2io_card_up(sp)) {
DBG_PRINT(ERR_DBG, "%s: H/W initialization failed\n",
dev->name);
- return -ENODEV;
+ err = -ENODEV;
+ goto hw_init_failed;
}
/* After proper initialization of H/W, register ISR */
- err = request_irq((int) sp->irq, s2io_isr, SA_SHIRQ,
+ err = request_irq((int) sp->pdev->irq, s2io_isr, SA_SHIRQ,
sp->name, dev);
if (err) {
- s2io_reset(sp);
DBG_PRINT(ERR_DBG, "%s: ISR registration failed\n",
dev->name);
- return err;
+ goto isr_registration_failed;
}
if (s2io_set_mac_addr(dev, dev->dev_addr) == FAILURE) {
DBG_PRINT(ERR_DBG, "Set Mac Address Failed\n");
- s2io_reset(sp);
- return -ENODEV;
+ err = -ENODEV;
+ goto setting_mac_address_failed;
}
netif_start_queue(dev);
return 0;
+
+setting_mac_address_failed:
+ free_irq(sp->pdev->irq, dev);
+isr_registration_failed:
+ del_timer_sync(&sp->alarm_timer);
+ s2io_reset(sp);
+hw_init_failed:
+ return err;
}
/**
@@ -2640,16 +3058,15 @@
* file on failure.
*/
-static int s2io_close(struct net_device *dev)
+int s2io_close(struct net_device *dev)
{
nic_t *sp = dev->priv;
-
flush_scheduled_work();
netif_stop_queue(dev);
/* Reset card, kill tasklet and free Tx and Rx buffers. */
s2io_card_down(sp);
- free_irq(dev->irq, dev);
+ free_irq(sp->pdev->irq, dev);
sp->device_close_flag = TRUE; /* Device is shut down. */
return 0;
}
@@ -2667,7 +3084,7 @@
* 0 on success & 1 on failure.
*/
-static int s2io_xmit(struct sk_buff *skb, struct net_device *dev)
+int s2io_xmit(struct sk_buff *skb, struct net_device *dev)
{
nic_t *sp = dev->priv;
u16 frg_cnt, frg_len, i, queue, queue_len, put_off, get_off;
@@ -2678,29 +3095,39 @@
#ifdef NETIF_F_TSO
int mss;
#endif
+ u16 vlan_tag = 0;
+ int vlan_priority = 0;
mac_info_t *mac_control;
struct config_param *config;
- XENA_dev_config_t __iomem *bar0 = sp->bar0;
mac_control = &sp->mac_control;
config = &sp->config;
- DBG_PRINT(TX_DBG, "%s: In S2IO Tx routine\n", dev->name);
+ DBG_PRINT(TX_DBG, "%s: In Neterion Tx routine\n", dev->name);
spin_lock_irqsave(&sp->tx_lock, flags);
-
if (atomic_read(&sp->card_state) == CARD_DOWN) {
- DBG_PRINT(ERR_DBG, "%s: Card going down for reset\n",
+ DBG_PRINT(TX_DBG, "%s: Card going down for reset\n",
dev->name);
spin_unlock_irqrestore(&sp->tx_lock, flags);
- return 1;
+ dev_kfree_skb(skb);
+ return 0;
}
queue = 0;
- put_off = (u16) mac_control->tx_curr_put_info[queue].offset;
- get_off = (u16) mac_control->tx_curr_get_info[queue].offset;
- txdp = (TxD_t *) sp->list_info[queue][put_off].list_virt_addr;
- queue_len = mac_control->tx_curr_put_info[queue].fifo_len + 1;
+ /* Get Fifo number to Transmit based on vlan priority */
+ if (sp->vlgrp && vlan_tx_tag_present(skb)) {
+ vlan_tag = vlan_tx_tag_get(skb);
+ vlan_priority = vlan_tag >> 13;
+ queue = config->fifo_mapping[vlan_priority];
+ }
+
+ put_off = (u16) mac_control->fifos[queue].tx_curr_put_info.offset;
+ get_off = (u16) mac_control->fifos[queue].tx_curr_get_info.offset;
+ txdp = (TxD_t *) mac_control->fifos[queue].list_info[put_off].
+ list_virt_addr;
+
+ queue_len = mac_control->fifos[queue].tx_curr_put_info.fifo_len + 1;
/* Avoid "put" pointer going beyond "get" pointer */
if (txdp->Host_Control || (((put_off + 1) % queue_len) == get_off)) {
DBG_PRINT(ERR_DBG, "Error in xmit, No free TXDs.\n");
@@ -2709,6 +3136,15 @@
spin_unlock_irqrestore(&sp->tx_lock, flags);
return 0;
}
+
+ /* A buffer with no data will be dropped */
+ if (!skb->len) {
+ DBG_PRINT(TX_DBG, "%s:Buffer has no data..\n", dev->name);
+ dev_kfree_skb(skb);
+ spin_unlock_irqrestore(&sp->tx_lock, flags);
+ return 0;
+ }
+
#ifdef NETIF_F_TSO
mss = skb_shinfo(skb)->tso_size;
if (mss) {
@@ -2720,9 +3156,9 @@
frg_cnt = skb_shinfo(skb)->nr_frags;
frg_len = skb->len - skb->data_len;
- txdp->Host_Control = (unsigned long) skb;
txdp->Buffer_Pointer = pci_map_single
(sp->pdev, skb->data, frg_len, PCI_DMA_TODEVICE);
+ txdp->Host_Control = (unsigned long) skb;
if (skb->ip_summed == CHECKSUM_HW) {
txdp->Control_2 |=
(TXD_TX_CKO_IPV4_EN | TXD_TX_CKO_TCP_EN |
@@ -2731,6 +3167,11 @@
txdp->Control_2 |= config->tx_intr_type;
+ if (sp->vlgrp && vlan_tx_tag_present(skb)) {
+ txdp->Control_2 |= TXD_VLAN_ENABLE;
+ txdp->Control_2 |= TXD_VLAN_TAG(vlan_tag);
+ }
+
txdp->Control_1 |= (TXD_BUFFER0_SIZE(frg_len) |
TXD_GATHER_CODE_FIRST);
txdp->Control_1 |= TXD_LIST_OWN_XENA;
@@ -2738,6 +3179,9 @@
/* For fragmented SKB. */
for (i = 0; i < frg_cnt; i++) {
skb_frag_t *frag = &skb_shinfo(skb)->frags[i];
+ /* A '0' length fragment will be ignored */
+ if (!frag->size)
+ continue;
txdp++;
txdp->Buffer_Pointer = (u64) pci_map_page
(sp->pdev, frag->page, frag->page_offset,
@@ -2747,23 +3191,23 @@
txdp->Control_1 |= TXD_GATHER_CODE_LAST;
tx_fifo = mac_control->tx_FIFO_start[queue];
- val64 = sp->list_info[queue][put_off].list_phy_addr;
+ val64 = mac_control->fifos[queue].list_info[put_off].list_phy_addr;
writeq(val64, &tx_fifo->TxDL_Pointer);
val64 = (TX_FIFO_LAST_TXD_NUM(frg_cnt) | TX_FIFO_FIRST_LIST |
TX_FIFO_LAST_LIST);
+
#ifdef NETIF_F_TSO
if (mss)
val64 |= TX_FIFO_SPECIAL_FUNC;
#endif
writeq(val64, &tx_fifo->List_Control);
- /* Perform a PCI read to flush previous writes */
- val64 = readq(&bar0->general_int_status);
+ mmiowb();
put_off++;
- put_off %= mac_control->tx_curr_put_info[queue].fifo_len + 1;
- mac_control->tx_curr_put_info[queue].offset = put_off;
+ put_off %= mac_control->fifos[queue].tx_curr_put_info.fifo_len + 1;
+ mac_control->fifos[queue].tx_curr_put_info.offset = put_off;
/* Avoid "put" pointer going beyond "get" pointer */
if (((put_off + 1) % queue_len) == get_off) {
@@ -2779,18 +3223,74 @@
return 0;
}
+static void
+s2io_alarm_handle(unsigned long data)
+{
+ nic_t *sp = (nic_t *)data;
+
+ alarm_intr_handler(sp);
+ mod_timer(&sp->alarm_timer, jiffies + HZ / 2);
+}
+
+static void s2io_txpic_intr_handle(nic_t *sp)
+{
+ XENA_dev_config_t *bar0 = (XENA_dev_config_t *) sp->bar0;
+ u64 val64;
+
+ val64 = readq(&bar0->pic_int_status);
+ if (val64 & PIC_INT_GPIO) {
+ val64 = readq(&bar0->gpio_int_reg);
+ if ((val64 & GPIO_INT_REG_LINK_DOWN) &&
+ (val64 & GPIO_INT_REG_LINK_UP)) {
+ val64 |= GPIO_INT_REG_LINK_DOWN;
+ val64 |= GPIO_INT_REG_LINK_UP;
+ writeq(val64, &bar0->gpio_int_reg);
+ goto masking;
+ }
+
+ if (((sp->last_link_state == LINK_UP) &&
+ (val64 & GPIO_INT_REG_LINK_DOWN)) ||
+ ((sp->last_link_state == LINK_DOWN) &&
+ (val64 & GPIO_INT_REG_LINK_UP))) {
+ val64 = readq(&bar0->gpio_int_mask);
+ val64 |= GPIO_INT_MASK_LINK_DOWN;
+ val64 |= GPIO_INT_MASK_LINK_UP;
+ writeq(val64, &bar0->gpio_int_mask);
+ s2io_set_link((unsigned long)sp);
+ }
+masking:
+ if (sp->last_link_state == LINK_UP) {
+ /*enable down interrupt */
+ val64 = readq(&bar0->gpio_int_mask);
+ /* unmasks link down intr */
+ val64 &= ~GPIO_INT_MASK_LINK_DOWN;
+ /* masks link up intr */
+ val64 |= GPIO_INT_MASK_LINK_UP;
+ writeq(val64, &bar0->gpio_int_mask);
+ } else {
+ /*enable UP Interrupt */
+ val64 = readq(&bar0->gpio_int_mask);
+ /* unmasks link up interrupt */
+ val64 &= ~GPIO_INT_MASK_LINK_UP;
+ /* masks link down interrupt */
+ val64 |= GPIO_INT_MASK_LINK_DOWN;
+ writeq(val64, &bar0->gpio_int_mask);
+ }
+ }
+}
+
/**
* s2io_isr - ISR handler of the device .
* @irq: the irq of the device.
* @dev_id: a void pointer to the dev structure of the NIC.
* @pt_regs: pointer to the registers pushed on the stack.
- * Description: This function is the ISR handler of the device. It
- * identifies the reason for the interrupt and calls the relevant
- * service routines. As a contongency measure, this ISR allocates the
+ * Description: This function is the ISR handler of the device. It
+ * identifies the reason for the interrupt and calls the relevant
+ * service routines. As a contongency measure, this ISR allocates the
* recv buffers, if their numbers are below the panic value which is
* presently set to 25% of the original number of rcv buffers allocated.
* Return value:
- * IRQ_HANDLED: will be returned if IRQ was handled by this routine
+ * IRQ_HANDLED: will be returned if IRQ was handled by this routine
* IRQ_NONE: will be returned if interrupt is not from our device
*/
static irqreturn_t s2io_isr(int irq, void *dev_id, struct pt_regs *regs)
@@ -2798,40 +3298,31 @@
struct net_device *dev = (struct net_device *) dev_id;
nic_t *sp = dev->priv;
XENA_dev_config_t __iomem *bar0 = sp->bar0;
-#ifndef CONFIG_S2IO_NAPI
- int i, ret;
-#endif
- u64 reason = 0;
+ int i;
+ u64 reason = 0, val64;
mac_info_t *mac_control;
struct config_param *config;
+ atomic_inc(&sp->isr_cnt);
mac_control = &sp->mac_control;
config = &sp->config;
- /*
+ /*
* Identify the cause for interrupt and call the appropriate
* interrupt handler. Causes for the interrupt could be;
* 1. Rx of packet.
* 2. Tx complete.
* 3. Link down.
- * 4. Error in any functional blocks of the NIC.
+ * 4. Error in any functional blocks of the NIC.
*/
reason = readq(&bar0->general_int_status);
if (!reason) {
/* The interrupt was not raised by Xena. */
+ atomic_dec(&sp->isr_cnt);
return IRQ_NONE;
}
- /* If Intr is because of Tx Traffic */
- if (reason & GEN_INTR_TXTRAFFIC) {
- tx_intr_handler(sp);
- }
-
- /* If Intr is because of an error */
- if (reason & (GEN_ERROR_INTR))
- alarm_intr_handler(sp);
-
#ifdef CONFIG_S2IO_NAPI
if (reason & GEN_INTR_RXTRAFFIC) {
if (netif_rx_schedule_prep(dev)) {
@@ -2843,17 +3334,43 @@
#else
/* If Intr is because of Rx Traffic */
if (reason & GEN_INTR_RXTRAFFIC) {
- rx_intr_handler(sp);
+ /*
+ * rx_traffic_int reg is an R1 register, writing all 1's
+ * will ensure that the actual interrupt causing bit get's
+ * cleared and hence a read can be avoided.
+ */
+ val64 = 0xFFFFFFFFFFFFFFFFULL;
+ writeq(val64, &bar0->rx_traffic_int);
+ for (i = 0; i < config->rx_ring_num; i++) {
+ rx_intr_handler(&mac_control->rings[i]);
+ }
}
#endif
- /*
- * If the Rx buffer count is below the panic threshold then
- * reallocate the buffers from the interrupt handler itself,
+ /* If Intr is because of Tx Traffic */
+ if (reason & GEN_INTR_TXTRAFFIC) {
+ /*
+ * tx_traffic_int reg is an R1 register, writing all 1's
+ * will ensure that the actual interrupt causing bit get's
+ * cleared and hence a read can be avoided.
+ */
+ val64 = 0xFFFFFFFFFFFFFFFFULL;
+ writeq(val64, &bar0->tx_traffic_int);
+
+ for (i = 0; i < config->tx_fifo_num; i++)
+ tx_intr_handler(&mac_control->fifos[i]);
+ }
+
+ if (reason & GEN_INTR_TXPIC)
+ s2io_txpic_intr_handle(sp);
+ /*
+ * If the Rx buffer count is below the panic threshold then
+ * reallocate the buffers from the interrupt handler itself,
* else schedule a tasklet to reallocate the buffers.
*/
#ifndef CONFIG_S2IO_NAPI
for (i = 0; i < config->rx_ring_num; i++) {
+ int ret;
int rxb_size = atomic_read(&sp->rx_bufs_left[i]);
int level = rx_buffer_level(sp, rxb_size, i);
@@ -2865,6 +3382,7 @@
dev->name);
DBG_PRINT(ERR_DBG, " in ISR!!\n");
clear_bit(0, (&sp->tasklet_status));
+ atomic_dec(&sp->isr_cnt);
return IRQ_HANDLED;
}
clear_bit(0, (&sp->tasklet_status));
@@ -2874,33 +3392,69 @@
}
#endif
+ atomic_dec(&sp->isr_cnt);
return IRQ_HANDLED;
}
/**
- * s2io_get_stats - Updates the device statistics structure.
+ * s2io_updt_stats -
+ */
+static void s2io_updt_stats(nic_t *sp)
+{
+ XENA_dev_config_t __iomem *bar0 = sp->bar0;
+ u64 val64;
+ int cnt = 0;
+
+ if (atomic_read(&sp->card_state) == CARD_UP) {
+ /* Apprx 30us on a 133 MHz bus */
+ val64 = SET_UPDT_CLICKS(10) |
+ STAT_CFG_ONE_SHOT_EN | STAT_CFG_STAT_EN;
+ writeq(val64, &bar0->stat_cfg);
+ do {
+ udelay(100);
+ val64 = readq(&bar0->stat_cfg);
+ if (!(val64 & BIT(0)))
+ break;
+ cnt++;
+ if (cnt == 5)
+ break; /* Updt failed */
+ } while(1);
+ }
+}
+
+/**
+ * s2io_get_stats - Updates the device statistics structure.
* @dev : pointer to the device structure.
* Description:
- * This function updates the device statistics structure in the s2io_nic
+ * This function updates the device statistics structure in the s2io_nic
* structure and returns a pointer to the same.
* Return value:
* pointer to the updated net_device_stats structure.
*/
-static struct net_device_stats *s2io_get_stats(struct net_device *dev)
+struct net_device_stats *s2io_get_stats(struct net_device *dev)
{
nic_t *sp = dev->priv;
mac_info_t *mac_control;
struct config_param *config;
+
mac_control = &sp->mac_control;
config = &sp->config;
- sp->stats.tx_errors = mac_control->stats_info->tmac_any_err_frms;
- sp->stats.rx_errors = mac_control->stats_info->rmac_drop_frms;
- sp->stats.multicast = mac_control->stats_info->rmac_vld_mcst_frms;
+ /* Configure Stats for immediate updt */
+ s2io_updt_stats(sp);
+
+ sp->stats.tx_packets =
+ le32_to_cpu(mac_control->stats_info->tmac_frms);
+ sp->stats.tx_errors =
+ le32_to_cpu(mac_control->stats_info->tmac_any_err_frms);
+ sp->stats.rx_errors =
+ le32_to_cpu(mac_control->stats_info->rmac_drop_frms);
+ sp->stats.multicast =
+ le32_to_cpu(mac_control->stats_info->rmac_vld_mcst_frms);
sp->stats.rx_length_errors =
- mac_control->stats_info->rmac_long_frms;
+ le32_to_cpu(mac_control->stats_info->rmac_long_frms);
return (&sp->stats);
}
@@ -2909,8 +3463,8 @@
* s2io_set_multicast - entry point for multicast address enable/disable.
* @dev : pointer to the device structure
* Description:
- * This function is a driver entry point which gets called by the kernel
- * whenever multicast addresses must be enabled/disabled. This also gets
+ * This function is a driver entry point which gets called by the kernel
+ * whenever multicast addresses must be enabled/disabled. This also gets
* called to set/reset promiscuous mode. Depending on the deivce flag, we
* determine, if multicast address must be enabled or if promiscuous mode
* is to be disabled etc.
@@ -2948,6 +3502,8 @@
/* Disable all Multicast addresses */
writeq(RMAC_ADDR_DATA0_MEM_ADDR(dis_addr),
&bar0->rmac_addr_data0_mem);
+ writeq(RMAC_ADDR_DATA1_MEM_MASK(0x0),
+ &bar0->rmac_addr_data1_mem);
val64 = RMAC_ADDR_CMD_MEM_WE |
RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD |
RMAC_ADDR_CMD_MEM_OFFSET(sp->all_multi_pos);
@@ -3010,7 +3566,7 @@
writeq(RMAC_ADDR_DATA0_MEM_ADDR(dis_addr),
&bar0->rmac_addr_data0_mem);
writeq(RMAC_ADDR_DATA1_MEM_MASK(0ULL),
- &bar0->rmac_addr_data1_mem);
+ &bar0->rmac_addr_data1_mem);
val64 = RMAC_ADDR_CMD_MEM_WE |
RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD |
RMAC_ADDR_CMD_MEM_OFFSET
@@ -3039,8 +3595,7 @@
writeq(RMAC_ADDR_DATA0_MEM_ADDR(mac_addr),
&bar0->rmac_addr_data0_mem);
writeq(RMAC_ADDR_DATA1_MEM_MASK(0ULL),
- &bar0->rmac_addr_data1_mem);
-
+ &bar0->rmac_addr_data1_mem);
val64 = RMAC_ADDR_CMD_MEM_WE |
RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD |
RMAC_ADDR_CMD_MEM_OFFSET
@@ -3059,12 +3614,12 @@
}
/**
- * s2io_set_mac_addr - Programs the Xframe mac address
+ * s2io_set_mac_addr - Programs the Xframe mac address
* @dev : pointer to the device structure.
* @addr: a uchar pointer to the new mac address which is to be set.
- * Description : This procedure will program the Xframe to receive
+ * Description : This procedure will program the Xframe to receive
* frames with new Mac Address
- * Return value: SUCCESS on success and an appropriate (-)ve integer
+ * Return value: SUCCESS on success and an appropriate (-)ve integer
* as defined in errno.h file on failure.
*/
@@ -3075,10 +3630,10 @@
register u64 val64, mac_addr = 0;
int i;
- /*
+ /*
* Set the new MAC address as the new unicast filter and reflect this
* change on the device address registered with the OS. It will be
- * at offset 0.
+ * at offset 0.
*/
for (i = 0; i < ETH_ALEN; i++) {
mac_addr <<= 8;
@@ -3102,12 +3657,12 @@
}
/**
- * s2io_ethtool_sset - Sets different link parameters.
+ * s2io_ethtool_sset - Sets different link parameters.
* @sp : private member of the device structure, which is a pointer to the * s2io_nic structure.
* @info: pointer to the structure with parameters given by ethtool to set
* link information.
* Description:
- * The function sets different link parameters provided by the user onto
+ * The function sets different link parameters provided by the user onto
* the NIC.
* Return value:
* 0 on success.
@@ -3129,7 +3684,7 @@
}
/**
- * s2io_ethtol_gset - Return link specific information.
+ * s2io_ethtol_gset - Return link specific information.
* @sp : private member of the device structure, pointer to the
* s2io_nic structure.
* @info : pointer to the structure with parameters given by ethtool
@@ -3161,8 +3716,8 @@
}
/**
- * s2io_ethtool_gdrvinfo - Returns driver specific information.
- * @sp : private member of the device structure, which is a pointer to the
+ * s2io_ethtool_gdrvinfo - Returns driver specific information.
+ * @sp : private member of the device structure, which is a pointer to the
* s2io_nic structure.
* @info : pointer to the structure with parameters given by ethtool to
* return driver information.
@@ -3190,9 +3745,9 @@
/**
* s2io_ethtool_gregs - dumps the entire space of Xfame into the buffer.
- * @sp: private member of the device structure, which is a pointer to the
+ * @sp: private member of the device structure, which is a pointer to the
* s2io_nic structure.
- * @regs : pointer to the structure with parameters given by ethtool for
+ * @regs : pointer to the structure with parameters given by ethtool for
* dumping the registers.
* @reg_space: The input argumnet into which all the registers are dumped.
* Description:
@@ -3221,11 +3776,11 @@
/**
* s2io_phy_id - timer function that alternates adapter LED.
- * @data : address of the private member of the device structure, which
+ * @data : address of the private member of the device structure, which
* is a pointer to the s2io_nic structure, provided as an u32.
- * Description: This is actually the timer function that alternates the
- * adapter LED bit of the adapter control bit to set/reset every time on
- * invocation. The timer is set for 1/2 a second, hence tha NIC blinks
+ * Description: This is actually the timer function that alternates the
+ * adapter LED bit of the adapter control bit to set/reset every time on
+ * invocation. The timer is set for 1/2 a second, hence tha NIC blinks
* once every second.
*/
static void s2io_phy_id(unsigned long data)
@@ -3236,7 +3791,8 @@
u16 subid;
subid = sp->pdev->subsystem_device;
- if ((subid & 0xFF) >= 0x07) {
+ if ((sp->device_type == XFRAME_II_DEVICE) ||
+ ((subid & 0xFF) >= 0x07)) {
val64 = readq(&bar0->gpio_control);
val64 ^= GPIO_CTRL_GPIO_0;
writeq(val64, &bar0->gpio_control);
@@ -3253,12 +3809,12 @@
* s2io_ethtool_idnic - To physically identify the nic on the system.
* @sp : private member of the device structure, which is a pointer to the
* s2io_nic structure.
- * @id : pointer to the structure with identification parameters given by
+ * @id : pointer to the structure with identification parameters given by
* ethtool.
* Description: Used to physically identify the NIC on the system.
- * The Link LED will blink for a time specified by the user for
+ * The Link LED will blink for a time specified by the user for
* identification.
- * NOTE: The Link has to be Up to be able to blink the LED. Hence
+ * NOTE: The Link has to be Up to be able to blink the LED. Hence
* identification is possible only if it's link is up.
* Return value:
* int , returns 0 on success
@@ -3273,7 +3829,8 @@
subid = sp->pdev->subsystem_device;
last_gpio_ctrl_val = readq(&bar0->gpio_control);
- if ((subid & 0xFF) < 0x07) {
+ if ((sp->device_type == XFRAME_I_DEVICE) &&
+ ((subid & 0xFF) < 0x07)) {
val64 = readq(&bar0->adapter_control);
if (!(val64 & ADAPTER_CNTL_EN)) {
printk(KERN_ERR
@@ -3288,12 +3845,12 @@
}
mod_timer(&sp->id_timer, jiffies);
if (data)
- msleep(data * 1000);
+ msleep_interruptible(data * HZ);
else
- msleep(0xFFFFFFFF);
+ msleep_interruptible(MAX_FLICKER_TIME);
del_timer_sync(&sp->id_timer);
- if (CARDS_WITH_FAULTY_LINK_INDICATORS(subid)) {
+ if (CARDS_WITH_FAULTY_LINK_INDICATORS(sp->device_type, subid)) {
writeq(last_gpio_ctrl_val, &bar0->gpio_control);
last_gpio_ctrl_val = readq(&bar0->gpio_control);
}
@@ -3303,7 +3860,8 @@
/**
* s2io_ethtool_getpause_data -Pause frame frame generation and reception.
- * @sp : private member of the device structure, which is a pointer to the * s2io_nic structure.
+ * @sp : private member of the device structure, which is a pointer to the
+ * s2io_nic structure.
* @ep : pointer to the structure with pause parameters given by ethtool.
* Description:
* Returns the Pause frame generation and reception capability of the NIC.
@@ -3327,7 +3885,7 @@
/**
* s2io_ethtool_setpause_data - set/reset pause frame generation.
- * @sp : private member of the device structure, which is a pointer to the
+ * @sp : private member of the device structure, which is a pointer to the
* s2io_nic structure.
* @ep : pointer to the structure with pause parameters given by ethtool.
* Description:
@@ -3338,7 +3896,7 @@
*/
static int s2io_ethtool_setpause_data(struct net_device *dev,
- struct ethtool_pauseparam *ep)
+ struct ethtool_pauseparam *ep)
{
u64 val64;
nic_t *sp = dev->priv;
@@ -3359,13 +3917,13 @@
/**
* read_eeprom - reads 4 bytes of data from user given offset.
- * @sp : private member of the device structure, which is a pointer to the
+ * @sp : private member of the device structure, which is a pointer to the
* s2io_nic structure.
* @off : offset at which the data must be written
* @data : Its an output parameter where the data read at the given
- * offset is stored.
+ * offset is stored.
* Description:
- * Will read 4 bytes of data from the user given offset and return the
+ * Will read 4 bytes of data from the user given offset and return the
* read data.
* NOTE: Will allow to read only part of the EEPROM visible through the
* I2C bus.
@@ -3406,7 +3964,7 @@
* s2io_nic structure.
* @off : offset at which the data must be written
* @data : The data that is to be written
- * @cnt : Number of bytes of the data that are actually to be written into
+ * @cnt : Number of bytes of the data that are actually to be written into
* the Eeprom. (max of 3)
* Description:
* Actually writes the relevant part of the data value into the Eeprom
@@ -3443,7 +4001,7 @@
/**
* s2io_ethtool_geeprom - reads the value stored in the Eeprom.
* @sp : private member of the device structure, which is a pointer to the * s2io_nic structure.
- * @eeprom : pointer to the user level structure provided by ethtool,
+ * @eeprom : pointer to the user level structure provided by ethtool,
* containing all relevant information.
* @data_buf : user defined value to be written into Eeprom.
* Description: Reads the values stored in the Eeprom at given offset
@@ -3454,7 +4012,7 @@
*/
static int s2io_ethtool_geeprom(struct net_device *dev,
- struct ethtool_eeprom *eeprom, u8 * data_buf)
+ struct ethtool_eeprom *eeprom, u8 * data_buf)
{
u32 data, i, valid;
nic_t *sp = dev->priv;
@@ -3479,7 +4037,7 @@
* s2io_ethtool_seeprom - tries to write the user provided value in Eeprom
* @sp : private member of the device structure, which is a pointer to the
* s2io_nic structure.
- * @eeprom : pointer to the user level structure provided by ethtool,
+ * @eeprom : pointer to the user level structure provided by ethtool,
* containing all relevant information.
* @data_buf ; user defined value to be written into Eeprom.
* Description:
@@ -3527,8 +4085,8 @@
}
/**
- * s2io_register_test - reads and writes into all clock domains.
- * @sp : private member of the device structure, which is a pointer to the
+ * s2io_register_test - reads and writes into all clock domains.
+ * @sp : private member of the device structure, which is a pointer to the
* s2io_nic structure.
* @data : variable that returns the result of each of the test conducted b
* by the driver.
@@ -3545,8 +4103,8 @@
u64 val64 = 0;
int fail = 0;
- val64 = readq(&bar0->pcc_enable);
- if (val64 != 0xff00000000000000ULL) {
+ val64 = readq(&bar0->pif_rd_swapper_fb);
+ if (val64 != 0x123456789abcdefULL) {
fail = 1;
DBG_PRINT(INFO_DBG, "Read Test level 1 fails\n");
}
@@ -3590,13 +4148,13 @@
}
/**
- * s2io_eeprom_test - to verify that EEprom in the xena can be programmed.
+ * s2io_eeprom_test - to verify that EEprom in the xena can be programmed.
* @sp : private member of the device structure, which is a pointer to the
* s2io_nic structure.
* @data:variable that returns the result of each of the test conducted by
* the driver.
* Description:
- * Verify that EEPROM in the xena can be programmed using I2C_CONTROL
+ * Verify that EEPROM in the xena can be programmed using I2C_CONTROL
* register.
* Return value:
* 0 on success.
@@ -3661,14 +4219,14 @@
/**
* s2io_bist_test - invokes the MemBist test of the card .
- * @sp : private member of the device structure, which is a pointer to the
+ * @sp : private member of the device structure, which is a pointer to the
* s2io_nic structure.
- * @data:variable that returns the result of each of the test conducted by
+ * @data:variable that returns the result of each of the test conducted by
* the driver.
* Description:
* This invokes the MemBist test of the card. We give around
* 2 secs time for the Test to complete. If it's still not complete
- * within this peiod, we consider that the test failed.
+ * within this peiod, we consider that the test failed.
* Return value:
* 0 on success and -1 on failure.
*/
@@ -3697,13 +4255,13 @@
}
/**
- * s2io-link_test - verifies the link state of the nic
- * @sp ; private member of the device structure, which is a pointer to the
+ * s2io-link_test - verifies the link state of the nic
+ * @sp ; private member of the device structure, which is a pointer to the
* s2io_nic structure.
* @data: variable that returns the result of each of the test conducted by
* the driver.
* Description:
- * The function verifies the link state of the NIC and updates the input
+ * The function verifies the link state of the NIC and updates the input
* argument 'data' appropriately.
* Return value:
* 0 on success.
@@ -3722,13 +4280,13 @@
}
/**
- * s2io_rldram_test - offline test for access to the RldRam chip on the NIC
- * @sp - private member of the device structure, which is a pointer to the
+ * s2io_rldram_test - offline test for access to the RldRam chip on the NIC
+ * @sp - private member of the device structure, which is a pointer to the
* s2io_nic structure.
- * @data - variable that returns the result of each of the test
+ * @data - variable that returns the result of each of the test
* conducted by the driver.
* Description:
- * This is one of the offline test that tests the read and write
+ * This is one of the offline test that tests the read and write
* access to the RldRam chip on the NIC.
* Return value:
* 0 on success.
@@ -3833,7 +4391,7 @@
* s2io_nic structure.
* @ethtest : pointer to a ethtool command specific structure that will be
* returned to the user.
- * @data : variable that returns the result of each of the test
+ * @data : variable that returns the result of each of the test
* conducted by the driver.
* Description:
* This function conducts 6 tests ( 4 offline and 2 online) to determine
@@ -3851,23 +4409,18 @@
if (ethtest->flags == ETH_TEST_FL_OFFLINE) {
/* Offline Tests. */
- if (orig_state) {
+ if (orig_state)
s2io_close(sp->dev);
- s2io_set_swapper(sp);
- } else
- s2io_set_swapper(sp);
if (s2io_register_test(sp, &data[0]))
ethtest->flags |= ETH_TEST_FL_FAILED;
s2io_reset(sp);
- s2io_set_swapper(sp);
if (s2io_rldram_test(sp, &data[3]))
ethtest->flags |= ETH_TEST_FL_FAILED;
s2io_reset(sp);
- s2io_set_swapper(sp);
if (s2io_eeprom_test(sp, &data[1]))
ethtest->flags |= ETH_TEST_FL_FAILED;
@@ -3910,61 +4463,111 @@
nic_t *sp = dev->priv;
StatInfo_t *stat_info = sp->mac_control.stats_info;
- tmp_stats[i++] = le32_to_cpu(stat_info->tmac_frms);
- tmp_stats[i++] = le32_to_cpu(stat_info->tmac_data_octets);
+ s2io_updt_stats(sp);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->tmac_frms_oflow) << 32 |
+ le32_to_cpu(stat_info->tmac_frms);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->tmac_data_octets_oflow) << 32 |
+ le32_to_cpu(stat_info->tmac_data_octets);
tmp_stats[i++] = le64_to_cpu(stat_info->tmac_drop_frms);
- tmp_stats[i++] = le32_to_cpu(stat_info->tmac_mcst_frms);
- tmp_stats[i++] = le32_to_cpu(stat_info->tmac_bcst_frms);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->tmac_mcst_frms_oflow) << 32 |
+ le32_to_cpu(stat_info->tmac_mcst_frms);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->tmac_bcst_frms_oflow) << 32 |
+ le32_to_cpu(stat_info->tmac_bcst_frms);
tmp_stats[i++] = le64_to_cpu(stat_info->tmac_pause_ctrl_frms);
- tmp_stats[i++] = le32_to_cpu(stat_info->tmac_any_err_frms);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->tmac_any_err_frms_oflow) << 32 |
+ le32_to_cpu(stat_info->tmac_any_err_frms);
tmp_stats[i++] = le64_to_cpu(stat_info->tmac_vld_ip_octets);
- tmp_stats[i++] = le32_to_cpu(stat_info->tmac_vld_ip);
- tmp_stats[i++] = le32_to_cpu(stat_info->tmac_drop_ip);
- tmp_stats[i++] = le32_to_cpu(stat_info->tmac_icmp);
- tmp_stats[i++] = le32_to_cpu(stat_info->tmac_rst_tcp);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->tmac_vld_ip_oflow) << 32 |
+ le32_to_cpu(stat_info->tmac_vld_ip);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->tmac_drop_ip_oflow) << 32 |
+ le32_to_cpu(stat_info->tmac_drop_ip);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->tmac_icmp_oflow) << 32 |
+ le32_to_cpu(stat_info->tmac_icmp);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->tmac_rst_tcp_oflow) << 32 |
+ le32_to_cpu(stat_info->tmac_rst_tcp);
tmp_stats[i++] = le64_to_cpu(stat_info->tmac_tcp);
- tmp_stats[i++] = le32_to_cpu(stat_info->tmac_udp);
- tmp_stats[i++] = le32_to_cpu(stat_info->rmac_vld_frms);
- tmp_stats[i++] = le32_to_cpu(stat_info->rmac_data_octets);
+ tmp_stats[i++] = (u64)le32_to_cpu(stat_info->tmac_udp_oflow) << 32 |
+ le32_to_cpu(stat_info->tmac_udp);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->rmac_vld_frms_oflow) << 32 |
+ le32_to_cpu(stat_info->rmac_vld_frms);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->rmac_data_octets_oflow) << 32 |
+ le32_to_cpu(stat_info->rmac_data_octets);
tmp_stats[i++] = le64_to_cpu(stat_info->rmac_fcs_err_frms);
tmp_stats[i++] = le64_to_cpu(stat_info->rmac_drop_frms);
- tmp_stats[i++] = le32_to_cpu(stat_info->rmac_vld_mcst_frms);
- tmp_stats[i++] = le32_to_cpu(stat_info->rmac_vld_bcst_frms);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->rmac_vld_mcst_frms_oflow) << 32 |
+ le32_to_cpu(stat_info->rmac_vld_mcst_frms);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->rmac_vld_bcst_frms_oflow) << 32 |
+ le32_to_cpu(stat_info->rmac_vld_bcst_frms);
tmp_stats[i++] = le32_to_cpu(stat_info->rmac_in_rng_len_err_frms);
tmp_stats[i++] = le64_to_cpu(stat_info->rmac_long_frms);
tmp_stats[i++] = le64_to_cpu(stat_info->rmac_pause_ctrl_frms);
- tmp_stats[i++] = le32_to_cpu(stat_info->rmac_discarded_frms);
- tmp_stats[i++] = le32_to_cpu(stat_info->rmac_usized_frms);
- tmp_stats[i++] = le32_to_cpu(stat_info->rmac_osized_frms);
- tmp_stats[i++] = le32_to_cpu(stat_info->rmac_frag_frms);
- tmp_stats[i++] = le32_to_cpu(stat_info->rmac_jabber_frms);
- tmp_stats[i++] = le32_to_cpu(stat_info->rmac_ip);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->rmac_discarded_frms_oflow) << 32 |
+ le32_to_cpu(stat_info->rmac_discarded_frms);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->rmac_usized_frms_oflow) << 32 |
+ le32_to_cpu(stat_info->rmac_usized_frms);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->rmac_osized_frms_oflow) << 32 |
+ le32_to_cpu(stat_info->rmac_osized_frms);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->rmac_frag_frms_oflow) << 32 |
+ le32_to_cpu(stat_info->rmac_frag_frms);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->rmac_jabber_frms_oflow) << 32 |
+ le32_to_cpu(stat_info->rmac_jabber_frms);
+ tmp_stats[i++] = (u64)le32_to_cpu(stat_info->rmac_ip_oflow) << 32 |
+ le32_to_cpu(stat_info->rmac_ip);
tmp_stats[i++] = le64_to_cpu(stat_info->rmac_ip_octets);
tmp_stats[i++] = le32_to_cpu(stat_info->rmac_hdr_err_ip);
- tmp_stats[i++] = le32_to_cpu(stat_info->rmac_drop_ip);
- tmp_stats[i++] = le32_to_cpu(stat_info->rmac_icmp);
+ tmp_stats[i++] = (u64)le32_to_cpu(stat_info->rmac_drop_ip_oflow) << 32 |
+ le32_to_cpu(stat_info->rmac_drop_ip);
+ tmp_stats[i++] = (u64)le32_to_cpu(stat_info->rmac_icmp_oflow) << 32 |
+ le32_to_cpu(stat_info->rmac_icmp);
tmp_stats[i++] = le64_to_cpu(stat_info->rmac_tcp);
- tmp_stats[i++] = le32_to_cpu(stat_info->rmac_udp);
- tmp_stats[i++] = le32_to_cpu(stat_info->rmac_err_drp_udp);
- tmp_stats[i++] = le32_to_cpu(stat_info->rmac_pause_cnt);
- tmp_stats[i++] = le32_to_cpu(stat_info->rmac_accepted_ip);
+ tmp_stats[i++] = (u64)le32_to_cpu(stat_info->rmac_udp_oflow) << 32 |
+ le32_to_cpu(stat_info->rmac_udp);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->rmac_err_drp_udp_oflow) << 32 |
+ le32_to_cpu(stat_info->rmac_err_drp_udp);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->rmac_pause_cnt_oflow) << 32 |
+ le32_to_cpu(stat_info->rmac_pause_cnt);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->rmac_accepted_ip_oflow) << 32 |
+ le32_to_cpu(stat_info->rmac_accepted_ip);
tmp_stats[i++] = le32_to_cpu(stat_info->rmac_err_tcp);
+ tmp_stats[i++] = 0;
+ tmp_stats[i++] = stat_info->sw_stat.single_ecc_errs;
+ tmp_stats[i++] = stat_info->sw_stat.double_ecc_errs;
}
-static int s2io_ethtool_get_regs_len(struct net_device *dev)
+int s2io_ethtool_get_regs_len(struct net_device *dev)
{
return (XENA_REG_SPACE);
}
-static u32 s2io_ethtool_get_rx_csum(struct net_device * dev)
+u32 s2io_ethtool_get_rx_csum(struct net_device * dev)
{
nic_t *sp = dev->priv;
return (sp->rx_csum);
}
-
-static int s2io_ethtool_set_rx_csum(struct net_device *dev, u32 data)
+int s2io_ethtool_set_rx_csum(struct net_device *dev, u32 data)
{
nic_t *sp = dev->priv;
@@ -3975,19 +4578,17 @@
return 0;
}
-
-static int s2io_get_eeprom_len(struct net_device *dev)
+int s2io_get_eeprom_len(struct net_device *dev)
{
return (XENA_EEPROM_SPACE);
}
-static int s2io_ethtool_self_test_count(struct net_device *dev)
+int s2io_ethtool_self_test_count(struct net_device *dev)
{
return (S2IO_TEST_LEN);
}
-
-static void s2io_ethtool_get_strings(struct net_device *dev,
- u32 stringset, u8 * data)
+void s2io_ethtool_get_strings(struct net_device *dev,
+ u32 stringset, u8 * data)
{
switch (stringset) {
case ETH_SS_TEST:
@@ -3998,13 +4599,12 @@
sizeof(ethtool_stats_keys));
}
}
-
static int s2io_ethtool_get_stats_count(struct net_device *dev)
{
return (S2IO_STAT_LEN);
}
-static int s2io_ethtool_op_set_tx_csum(struct net_device *dev, u32 data)
+int s2io_ethtool_op_set_tx_csum(struct net_device *dev, u32 data)
{
if (data)
dev->features |= NETIF_F_IP_CSUM;
@@ -4046,21 +4646,18 @@
};
/**
- * s2io_ioctl - Entry point for the Ioctl
+ * s2io_ioctl - Entry point for the Ioctl
* @dev : Device pointer.
* @ifr : An IOCTL specefic structure, that can contain a pointer to
* a proprietary structure used to pass information to the driver.
* @cmd : This is used to distinguish between the different commands that
* can be passed to the IOCTL functions.
* Description:
- * This function has support for ethtool, adding multiple MAC addresses on
- * the NIC and some DBG commands for the util tool.
- * Return value:
- * Currently the IOCTL supports no operations, hence by default this
- * function returns OP NOT SUPPORTED value.
+ * Currently there are no special functionality supported in IOCTL, hence
+ * function always return EOPNOTSUPPORTED
*/
-static int s2io_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
+int s2io_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
{
return -EOPNOTSUPP;
}
@@ -4076,17 +4673,9 @@
* file on failure.
*/
-static int s2io_change_mtu(struct net_device *dev, int new_mtu)
+int s2io_change_mtu(struct net_device *dev, int new_mtu)
{
nic_t *sp = dev->priv;
- XENA_dev_config_t __iomem *bar0 = sp->bar0;
- register u64 val64;
-
- if (netif_running(dev)) {
- DBG_PRINT(ERR_DBG, "%s: Must be stopped to ", dev->name);
- DBG_PRINT(ERR_DBG, "change its MTU \n");
- return -EBUSY;
- }
if ((new_mtu < MIN_MTU) || (new_mtu > S2IO_JUMBO_SIZE)) {
DBG_PRINT(ERR_DBG, "%s: MTU size is invalid.\n",
@@ -4094,11 +4683,22 @@
return -EPERM;
}
- /* Set the new MTU into the PYLD register of the NIC */
- val64 = new_mtu;
- writeq(vBIT(val64, 2, 14), &bar0->rmac_max_pyld_len);
-
dev->mtu = new_mtu;
+ if (netif_running(dev)) {
+ s2io_card_down(sp);
+ netif_stop_queue(dev);
+ if (s2io_card_up(sp)) {
+ DBG_PRINT(ERR_DBG, "%s: Device bring up failed\n",
+ __FUNCTION__);
+ }
+ if (netif_queue_stopped(dev))
+ netif_wake_queue(dev);
+ } else { /* Device is down */
+ XENA_dev_config_t __iomem *bar0 = sp->bar0;
+ u64 val64 = new_mtu;
+
+ writeq(vBIT(val64, 2, 14), &bar0->rmac_max_pyld_len);
+ }
return 0;
}
@@ -4108,9 +4708,9 @@
* @dev_adr : address of the device structure in dma_addr_t format.
* Description:
* This is the tasklet or the bottom half of the ISR. This is
- * an extension of the ISR which is scheduled by the scheduler to be run
+ * an extension of the ISR which is scheduled by the scheduler to be run
* when the load on the CPU is low. All low priority tasks of the ISR can
- * be pushed into the tasklet. For now the tasklet is used only to
+ * be pushed into the tasklet. For now the tasklet is used only to
* replenish the Rx buffers in the Rx buffer descriptors.
* Return value:
* void.
@@ -4166,19 +4766,22 @@
}
subid = nic->pdev->subsystem_device;
- /*
- * Allow a small delay for the NICs self initiated
- * cleanup to complete.
- */
- msleep(100);
+ if (s2io_link_fault_indication(nic) == MAC_RMAC_ERR_TIMER) {
+ /*
+ * Allow a small delay for the NICs self initiated
+ * cleanup to complete.
+ */
+ msleep(100);
+ }
val64 = readq(&bar0->adapter_status);
- if (verify_xena_quiescence(val64, nic->device_enabled_once)) {
+ if (verify_xena_quiescence(nic, val64, nic->device_enabled_once)) {
if (LINK_IS_UP(val64)) {
val64 = readq(&bar0->adapter_control);
val64 |= ADAPTER_CNTL_EN;
writeq(val64, &bar0->adapter_control);
- if (CARDS_WITH_FAULTY_LINK_INDICATORS(subid)) {
+ if (CARDS_WITH_FAULTY_LINK_INDICATORS(nic->device_type,
+ subid)) {
val64 = readq(&bar0->gpio_control);
val64 |= GPIO_CTRL_GPIO_0;
writeq(val64, &bar0->gpio_control);
@@ -4187,20 +4790,24 @@
val64 |= ADAPTER_LED_ON;
writeq(val64, &bar0->adapter_control);
}
- val64 = readq(&bar0->adapter_status);
- if (!LINK_IS_UP(val64)) {
- DBG_PRINT(ERR_DBG, "%s:", dev->name);
- DBG_PRINT(ERR_DBG, " Link down");
- DBG_PRINT(ERR_DBG, "after ");
- DBG_PRINT(ERR_DBG, "enabling ");
- DBG_PRINT(ERR_DBG, "device \n");
+ if (s2io_link_fault_indication(nic) ==
+ MAC_RMAC_ERR_TIMER) {
+ val64 = readq(&bar0->adapter_status);
+ if (!LINK_IS_UP(val64)) {
+ DBG_PRINT(ERR_DBG, "%s:", dev->name);
+ DBG_PRINT(ERR_DBG, " Link down");
+ DBG_PRINT(ERR_DBG, "after ");
+ DBG_PRINT(ERR_DBG, "enabling ");
+ DBG_PRINT(ERR_DBG, "device \n");
+ }
}
if (nic->device_enabled_once == FALSE) {
nic->device_enabled_once = TRUE;
}
s2io_link(nic, LINK_UP);
} else {
- if (CARDS_WITH_FAULTY_LINK_INDICATORS(subid)) {
+ if (CARDS_WITH_FAULTY_LINK_INDICATORS(nic->device_type,
+ subid)) {
val64 = readq(&bar0->gpio_control);
val64 &= ~GPIO_CTRL_GPIO_0;
writeq(val64, &bar0->gpio_control);
@@ -4223,9 +4830,11 @@
unsigned long flags;
register u64 val64 = 0;
+ del_timer_sync(&sp->alarm_timer);
/* If s2io_set_link task is executing, wait till it completes. */
- while (test_and_set_bit(0, &(sp->link_state)))
+ while (test_and_set_bit(0, &(sp->link_state))) {
msleep(50);
+ }
atomic_set(&sp->card_state, CARD_DOWN);
/* disable Tx and Rx traffic on the NIC */
@@ -4237,7 +4846,7 @@
/* Check if the device is Quiescent and then Reset the NIC */
do {
val64 = readq(&bar0->adapter_status);
- if (verify_xena_quiescence(val64, sp->device_enabled_once)) {
+ if (verify_xena_quiescence(sp, val64, sp->device_enabled_once)) {
break;
}
@@ -4251,14 +4860,27 @@
break;
}
} while (1);
- spin_lock_irqsave(&sp->tx_lock, flags);
s2io_reset(sp);
- /* Free all unused Tx and Rx buffers */
- free_tx_buffers(sp);
- free_rx_buffers(sp);
+ /* Waiting till all Interrupt handlers are complete */
+ cnt = 0;
+ do {
+ msleep(10);
+ if (!atomic_read(&sp->isr_cnt))
+ break;
+ cnt++;
+ } while(cnt < 5);
+ spin_lock_irqsave(&sp->tx_lock, flags);
+ /* Free all Tx buffers */
+ free_tx_buffers(sp);
spin_unlock_irqrestore(&sp->tx_lock, flags);
+
+ /* Free all Rx buffers */
+ spin_lock_irqsave(&sp->rx_lock, flags);
+ free_rx_buffers(sp);
+ spin_unlock_irqrestore(&sp->rx_lock, flags);
+
clear_bit(0, &(sp->link_state));
}
@@ -4276,8 +4898,8 @@
return -ENODEV;
}
- /*
- * Initializing the Rx buffers. For now we are considering only 1
+ /*
+ * Initializing the Rx buffers. For now we are considering only 1
* Rx ring and initializing buffers into 30 Rx blocks
*/
mac_control = &sp->mac_control;
@@ -4311,16 +4933,18 @@
return -ENODEV;
}
+ S2IO_TIMER_CONF(sp->alarm_timer, s2io_alarm_handle, sp, (HZ/2));
+
atomic_set(&sp->card_state, CARD_UP);
return 0;
}
-/**
+/**
* s2io_restart_nic - Resets the NIC.
* @data : long pointer to the device private structure
* Description:
* This function is scheduled to be run by the s2io_tx_watchdog
- * function after 0.5 secs to reset the NIC. The idea is to reduce
+ * function after 0.5 secs to reset the NIC. The idea is to reduce
* the run time of the watch dog routine which is run holding a
* spin lock.
*/
@@ -4338,10 +4962,11 @@
netif_wake_queue(dev);
DBG_PRINT(ERR_DBG, "%s: was reset by Tx watchdog timer\n",
dev->name);
+
}
-/**
- * s2io_tx_watchdog - Watchdog for transmit side.
+/**
+ * s2io_tx_watchdog - Watchdog for transmit side.
* @dev : Pointer to net device structure
* Description:
* This function is triggered if the Tx Queue is stopped
@@ -4369,7 +4994,7 @@
* @len : length of the packet
* @cksum : FCS checksum of the frame.
* @ring_no : the ring from which this RxD was extracted.
- * Description:
+ * Description:
* This function is called by the Tx interrupt serivce routine to perform
* some OS related operations on the SKB before passing it to the upper
* layers. It mainly checks if the checksum is OK, if so adds it to the
@@ -4379,71 +5004,38 @@
* Return value:
* SUCCESS on success and -1 on failure.
*/
-#ifndef CONFIG_2BUFF_MODE
-static int rx_osm_handler(nic_t * sp, u16 len, RxD_t * rxdp, int ring_no)
-#else
-static int rx_osm_handler(nic_t * sp, RxD_t * rxdp, int ring_no,
- buffAdd_t * ba)
-#endif
+static int rx_osm_handler(ring_info_t *ring_data, RxD_t * rxdp)
{
+ nic_t *sp = ring_data->nic;
struct net_device *dev = (struct net_device *) sp->dev;
- struct sk_buff *skb =
- (struct sk_buff *) ((unsigned long) rxdp->Host_Control);
+ struct sk_buff *skb = (struct sk_buff *)
+ ((unsigned long) rxdp->Host_Control);
+ int ring_no = ring_data->ring_no;
u16 l3_csum, l4_csum;
#ifdef CONFIG_2BUFF_MODE
- int buf0_len, buf2_len;
+ int buf0_len = RXD_GET_BUFFER0_SIZE(rxdp->Control_2);
+ int buf2_len = RXD_GET_BUFFER2_SIZE(rxdp->Control_2);
+ int get_block = ring_data->rx_curr_get_info.block_index;
+ int get_off = ring_data->rx_curr_get_info.offset;
+ buffAdd_t *ba = &ring_data->ba[get_block][get_off];
unsigned char *buff;
+#else
+ u16 len = (u16) ((RXD_GET_BUFFER0_SIZE(rxdp->Control_2)) >> 48);;
#endif
-
- l3_csum = RXD_GET_L3_CKSUM(rxdp->Control_1);
- if ((rxdp->Control_1 & TCP_OR_UDP_FRAME) && (sp->rx_csum)) {
- l4_csum = RXD_GET_L4_CKSUM(rxdp->Control_1);
- if ((l3_csum == L3_CKSUM_OK) && (l4_csum == L4_CKSUM_OK)) {
- /*
- * NIC verifies if the Checksum of the received
- * frame is Ok or not and accordingly returns
- * a flag in the RxD.
- */
- skb->ip_summed = CHECKSUM_UNNECESSARY;
- } else {
- /*
- * Packet with erroneous checksum, let the
- * upper layers deal with it.
- */
- skb->ip_summed = CHECKSUM_NONE;
- }
- } else {
- skb->ip_summed = CHECKSUM_NONE;
- }
-
+ skb->dev = dev;
if (rxdp->Control_1 & RXD_T_CODE) {
unsigned long long err = rxdp->Control_1 & RXD_T_CODE;
DBG_PRINT(ERR_DBG, "%s: Rx error Value: 0x%llx\n",
dev->name, err);
+ dev_kfree_skb(skb);
+ sp->stats.rx_crc_errors++;
+ atomic_dec(&sp->rx_bufs_left[ring_no]);
+ rxdp->Host_Control = 0;
+ return 0;
}
-#ifdef CONFIG_2BUFF_MODE
- buf0_len = RXD_GET_BUFFER0_SIZE(rxdp->Control_2);
- buf2_len = RXD_GET_BUFFER2_SIZE(rxdp->Control_2);
-#endif
- skb->dev = dev;
-#ifndef CONFIG_2BUFF_MODE
- skb_put(skb, len);
- skb->protocol = eth_type_trans(skb, dev);
-#else
- buff = skb_push(skb, buf0_len);
- memcpy(buff, ba->ba_0, buf0_len);
- skb_put(skb, buf2_len);
- skb->protocol = eth_type_trans(skb, dev);
-#endif
-
-#ifdef CONFIG_S2IO_NAPI
- netif_receive_skb(skb);
-#else
- netif_rx(skb);
-#endif
-
- dev->last_rx = jiffies;
+ /* Updating statistics */
+ rxdp->Host_Control = 0;
sp->rx_pkt_count++;
sp->stats.rx_packets++;
#ifndef CONFIG_2BUFF_MODE
@@ -4452,8 +5044,56 @@
sp->stats.rx_bytes += buf0_len + buf2_len;
#endif
+#ifndef CONFIG_2BUFF_MODE
+ skb_put(skb, len);
+#else
+ buff = skb_push(skb, buf0_len);
+ memcpy(buff, ba->ba_0, buf0_len);
+ skb_put(skb, buf2_len);
+#endif
+
+ if ((rxdp->Control_1 & TCP_OR_UDP_FRAME) &&
+ (sp->rx_csum)) {
+ l3_csum = RXD_GET_L3_CKSUM(rxdp->Control_1);
+ l4_csum = RXD_GET_L4_CKSUM(rxdp->Control_1);
+ if ((l3_csum == L3_CKSUM_OK) && (l4_csum == L4_CKSUM_OK)) {
+ /*
+ * NIC verifies if the Checksum of the received
+ * frame is Ok or not and accordingly returns
+ * a flag in the RxD.
+ */
+ skb->ip_summed = CHECKSUM_UNNECESSARY;
+ } else {
+ /*
+ * Packet with erroneous checksum, let the
+ * upper layers deal with it.
+ */
+ skb->ip_summed = CHECKSUM_NONE;
+ }
+ } else {
+ skb->ip_summed = CHECKSUM_NONE;
+ }
+
+ skb->protocol = eth_type_trans(skb, dev);
+#ifdef CONFIG_S2IO_NAPI
+ if (sp->vlgrp && RXD_GET_VLAN_TAG(rxdp->Control_2)) {
+ /* Queueing the vlan frame to the upper layer */
+ vlan_hwaccel_receive_skb(skb, sp->vlgrp,
+ RXD_GET_VLAN_TAG(rxdp->Control_2));
+ } else {
+ netif_receive_skb(skb);
+ }
+#else
+ if (sp->vlgrp && RXD_GET_VLAN_TAG(rxdp->Control_2)) {
+ /* Queueing the vlan frame to the upper layer */
+ vlan_hwaccel_rx(skb, sp->vlgrp,
+ RXD_GET_VLAN_TAG(rxdp->Control_2));
+ } else {
+ netif_rx(skb);
+ }
+#endif
+ dev->last_rx = jiffies;
atomic_dec(&sp->rx_bufs_left[ring_no]);
- rxdp->Host_Control = 0;
return SUCCESS;
}
@@ -4464,13 +5104,13 @@
* @link : inidicates whether link is UP/DOWN.
* Description:
* This function stops/starts the Tx queue depending on whether the link
- * status of the NIC is is down or up. This is called by the Alarm
- * interrupt handler whenever a link change interrupt comes up.
+ * status of the NIC is is down or up. This is called by the Alarm
+ * interrupt handler whenever a link change interrupt comes up.
* Return value:
* void.
*/
-static void s2io_link(nic_t * sp, int link)
+void s2io_link(nic_t * sp, int link)
{
struct net_device *dev = (struct net_device *) sp->dev;
@@ -4487,8 +5127,25 @@
}
/**
- * s2io_init_pci -Initialization of PCI and PCI-X configuration registers .
- * @sp : private member of the device structure, which is a pointer to the
+ * get_xena_rev_id - to identify revision ID of xena.
+ * @pdev : PCI Dev structure
+ * Description:
+ * Function to identify the Revision ID of xena.
+ * Return value:
+ * returns the revision ID of the device.
+ */
+
+int get_xena_rev_id(struct pci_dev *pdev)
+{
+ u8 id = 0;
+ int ret;
+ ret = pci_read_config_byte(pdev, PCI_REVISION_ID, (u8 *) & id);
+ return id;
+}
+
+/**
+ * s2io_init_pci -Initialization of PCI and PCI-X configuration registers .
+ * @sp : private member of the device structure, which is a pointer to the
* s2io_nic structure.
* Description:
* This function initializes a few of the PCI and PCI-X configuration registers
@@ -4499,15 +5156,15 @@
static void s2io_init_pci(nic_t * sp)
{
- u16 pci_cmd = 0;
+ u16 pci_cmd = 0, pcix_cmd = 0;
/* Enable Data Parity Error Recovery in PCI-X command register. */
pci_read_config_word(sp->pdev, PCIX_COMMAND_REGISTER,
- &(sp->pcix_cmd));
+ &(pcix_cmd));
pci_write_config_word(sp->pdev, PCIX_COMMAND_REGISTER,
- (sp->pcix_cmd | 1));
+ (pcix_cmd | 1));
pci_read_config_word(sp->pdev, PCIX_COMMAND_REGISTER,
- &(sp->pcix_cmd));
+ &(pcix_cmd));
/* Set the PErr Response bit in PCI command register. */
pci_read_config_word(sp->pdev, PCI_COMMAND, &pci_cmd);
@@ -4515,53 +5172,43 @@
(pci_cmd | PCI_COMMAND_PARITY));
pci_read_config_word(sp->pdev, PCI_COMMAND, &pci_cmd);
- /* Set MMRB count to 1024 in PCI-X Command register. */
- sp->pcix_cmd &= 0xFFF3;
- pci_write_config_word(sp->pdev, PCIX_COMMAND_REGISTER, (sp->pcix_cmd | (0x1 << 2))); /* MMRBC 1K */
- pci_read_config_word(sp->pdev, PCIX_COMMAND_REGISTER,
- &(sp->pcix_cmd));
-
- /* Setting Maximum outstanding splits based on system type. */
- sp->pcix_cmd &= 0xFF8F;
-
- sp->pcix_cmd |= XENA_MAX_OUTSTANDING_SPLITS(0x1); /* 2 splits. */
- pci_write_config_word(sp->pdev, PCIX_COMMAND_REGISTER,
- sp->pcix_cmd);
- pci_read_config_word(sp->pdev, PCIX_COMMAND_REGISTER,
- &(sp->pcix_cmd));
/* Forcibly disabling relaxed ordering capability of the card. */
- sp->pcix_cmd &= 0xfffd;
+ pcix_cmd &= 0xfffd;
pci_write_config_word(sp->pdev, PCIX_COMMAND_REGISTER,
- sp->pcix_cmd);
+ pcix_cmd);
pci_read_config_word(sp->pdev, PCIX_COMMAND_REGISTER,
- &(sp->pcix_cmd));
+ &(pcix_cmd));
}
MODULE_AUTHOR("Raghavendra Koushik <raghavendra.koushik@neterion.com>");
MODULE_LICENSE("GPL");
module_param(tx_fifo_num, int, 0);
-module_param_array(tx_fifo_len, int, NULL, 0);
module_param(rx_ring_num, int, 0);
-module_param_array(rx_ring_sz, int, NULL, 0);
-module_param(Stats_refresh_time, int, 0);
+module_param_array(tx_fifo_len, uint, NULL, 0);
+module_param_array(rx_ring_sz, uint, NULL, 0);
+module_param_array(rts_frm_len, uint, NULL, 0);
+module_param(use_continuous_tx_intrs, int, 1);
module_param(rmac_pause_time, int, 0);
module_param(mc_pause_threshold_q0q3, int, 0);
module_param(mc_pause_threshold_q4q7, int, 0);
module_param(shared_splits, int, 0);
module_param(tmac_util_period, int, 0);
module_param(rmac_util_period, int, 0);
+module_param(bimodal, bool, 0);
#ifndef CONFIG_S2IO_NAPI
module_param(indicate_max_pkts, int, 0);
#endif
+module_param(rxsync_frequency, int, 0);
+
/**
- * s2io_init_nic - Initialization of the adapter .
+ * s2io_init_nic - Initialization of the adapter .
* @pdev : structure containing the PCI related information of the device.
* @pre: List of PCI devices supported by the driver listed in s2io_tbl.
* Description:
* The function initializes an adapter identified by the pci_dec structure.
- * All OS related initialization including memory and device structure and
- * initlaization of the device private variable is done. Also the swapper
- * control register is initialized to enable read and write into the I/O
+ * All OS related initialization including memory and device structure and
+ * initlaization of the device private variable is done. Also the swapper
+ * control register is initialized to enable read and write into the I/O
* registers of the device.
* Return value:
* returns 0 on success and negative on failure.
@@ -4572,7 +5219,6 @@
{
nic_t *sp;
struct net_device *dev;
- char *dev_name = "S2IO 10GE NIC";
int i, j, ret;
int dma_flag = FALSE;
u32 mac_up, mac_down;
@@ -4581,10 +5227,11 @@
u16 subid;
mac_info_t *mac_control;
struct config_param *config;
+ int mode;
-
- DBG_PRINT(ERR_DBG, "Loading S2IO driver with %s\n",
- s2io_driver_version);
+#ifdef CONFIG_S2IO_NAPI
+ DBG_PRINT(ERR_DBG, "NAPI support has been enabled\n");
+#endif
if ((ret = pci_enable_device(pdev))) {
DBG_PRINT(ERR_DBG,
@@ -4595,7 +5242,6 @@
if (!pci_set_dma_mask(pdev, DMA_64BIT_MASK)) {
DBG_PRINT(INIT_DBG, "s2io_init_nic: Using 64bit DMA\n");
dma_flag = TRUE;
-
if (pci_set_consistent_dma_mask
(pdev, DMA_64BIT_MASK)) {
DBG_PRINT(ERR_DBG,
@@ -4635,34 +5281,41 @@
memset(sp, 0, sizeof(nic_t));
sp->dev = dev;
sp->pdev = pdev;
- sp->vendor_id = pdev->vendor;
- sp->device_id = pdev->device;
sp->high_dma_flag = dma_flag;
- sp->irq = pdev->irq;
sp->device_enabled_once = FALSE;
- strcpy(sp->name, dev_name);
+
+ if ((pdev->device == PCI_DEVICE_ID_HERC_WIN) ||
+ (pdev->device == PCI_DEVICE_ID_HERC_UNI))
+ sp->device_type = XFRAME_II_DEVICE;
+ else
+ sp->device_type = XFRAME_I_DEVICE;
/* Initialize some PCI/PCI-X fields of the NIC. */
s2io_init_pci(sp);
- /*
+ /*
* Setting the device configuration parameters.
- * Most of these parameters can be specified by the user during
- * module insertion as they are module loadable parameters. If
- * these parameters are not not specified during load time, they
+ * Most of these parameters can be specified by the user during
+ * module insertion as they are module loadable parameters. If
+ * these parameters are not not specified during load time, they
* are initialized with default values.
*/
mac_control = &sp->mac_control;
config = &sp->config;
/* Tx side parameters. */
- tx_fifo_len[0] = DEFAULT_FIFO_LEN; /* Default value. */
+ if (tx_fifo_len[0] == 0)
+ tx_fifo_len[0] = DEFAULT_FIFO_LEN; /* Default value. */
config->tx_fifo_num = tx_fifo_num;
for (i = 0; i < MAX_TX_FIFOS; i++) {
config->tx_cfg[i].fifo_len = tx_fifo_len[i];
config->tx_cfg[i].fifo_priority = i;
}
+ /* mapping the QoS priority to the configured fifos */
+ for (i = 0; i < MAX_TX_FIFOS; i++)
+ config->fifo_mapping[i] = fifo_map[config->tx_fifo_num][i];
+
config->tx_intr_type = TXD_INT_TYPE_UTILZ;
for (i = 0; i < config->tx_fifo_num; i++) {
config->tx_cfg[i].f_no_snoop =
@@ -4675,7 +5328,8 @@
config->max_txds = MAX_SKB_FRAGS;
/* Rx side parameters. */
- rx_ring_sz[0] = SMALL_BLK_CNT; /* Default value. */
+ if (rx_ring_sz[0] == 0)
+ rx_ring_sz[0] = SMALL_BLK_CNT; /* Default value. */
config->rx_ring_num = rx_ring_num;
for (i = 0; i < MAX_RX_RINGS; i++) {
config->rx_cfg[i].num_rxd = rx_ring_sz[i] *
@@ -4699,10 +5353,13 @@
for (i = 0; i < config->rx_ring_num; i++)
atomic_set(&sp->rx_bufs_left[i], 0);
+ /* Initialize the number of ISRs currently running */
+ atomic_set(&sp->isr_cnt, 0);
+
/* initialize the shared memory used by the NIC and the host */
if (init_shared_mem(sp)) {
DBG_PRINT(ERR_DBG, "%s: Memory allocation failed\n",
- dev->name);
+ __FUNCTION__);
ret = -ENOMEM;
goto mem_alloc_failed;
}
@@ -4743,13 +5400,17 @@
dev->do_ioctl = &s2io_ioctl;
dev->change_mtu = &s2io_change_mtu;
SET_ETHTOOL_OPS(dev, &netdev_ethtool_ops);
+ dev->features |= NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX;
+ dev->vlan_rx_register = s2io_vlan_rx_register;
+ dev->vlan_rx_kill_vid = (void *)s2io_vlan_rx_kill_vid;
+
/*
* will use eth_mac_addr() for dev->set_mac_address
* mac address will be set every time dev->open() is called
*/
-#ifdef CONFIG_S2IO_NAPI
+#if defined(CONFIG_S2IO_NAPI)
dev->poll = s2io_poll;
- dev->weight = 90;
+ dev->weight = 32;
#endif
dev->features |= NETIF_F_SG | NETIF_F_IP_CSUM;
@@ -4776,22 +5437,28 @@
goto set_swap_failed;
}
- /* Fix for all "FFs" MAC address problems observed on Alpha platforms */
- fix_mac_address(sp);
- s2io_reset(sp);
-
- /*
- * Setting swapper control on the NIC, so the MAC address can be read.
- */
- if (s2io_set_swapper(sp)) {
- DBG_PRINT(ERR_DBG,
- "%s: S2IO: swapper settings are wrong\n",
- dev->name);
- ret = -EAGAIN;
- goto set_swap_failed;
+ /* Verify if the Herc works on the slot its placed into */
+ if (sp->device_type & XFRAME_II_DEVICE) {
+ mode = s2io_verify_pci_mode(sp);
+ if (mode < 0) {
+ DBG_PRINT(ERR_DBG, "%s: ", __FUNCTION__);
+ DBG_PRINT(ERR_DBG, " Unsupported PCI bus mode\n");
+ ret = -EBADSLT;
+ goto set_swap_failed;
+ }
}
- /*
+ /* Not needed for Herc */
+ if (sp->device_type & XFRAME_I_DEVICE) {
+ /*
+ * Fix for all "FFs" MAC address problems observed on
+ * Alpha platforms
+ */
+ fix_mac_address(sp);
+ s2io_reset(sp);
+ }
+
+ /*
* MAC address initialization.
* For now only one mac address will be read and used.
*/
@@ -4814,37 +5481,28 @@
sp->def_mac_addr[0].mac_addr[5] = (u8) (mac_down >> 16);
sp->def_mac_addr[0].mac_addr[4] = (u8) (mac_down >> 24);
- DBG_PRINT(INIT_DBG,
- "DEFAULT MAC ADDR:0x%02x-%02x-%02x-%02x-%02x-%02x\n",
- sp->def_mac_addr[0].mac_addr[0],
- sp->def_mac_addr[0].mac_addr[1],
- sp->def_mac_addr[0].mac_addr[2],
- sp->def_mac_addr[0].mac_addr[3],
- sp->def_mac_addr[0].mac_addr[4],
- sp->def_mac_addr[0].mac_addr[5]);
-
/* Set the factory defined MAC address initially */
dev->addr_len = ETH_ALEN;
memcpy(dev->dev_addr, sp->def_mac_addr, ETH_ALEN);
/*
- * Initialize the tasklet status and link state flags
- * and the card statte parameter
+ * Initialize the tasklet status and link state flags
+ * and the card state parameter
*/
atomic_set(&(sp->card_state), 0);
sp->tasklet_status = 0;
sp->link_state = 0;
-
/* Initialize spinlocks */
spin_lock_init(&sp->tx_lock);
#ifndef CONFIG_S2IO_NAPI
spin_lock_init(&sp->put_lock);
#endif
+ spin_lock_init(&sp->rx_lock);
- /*
- * SXE-002: Configure link and activity LED to init state
- * on driver load.
+ /*
+ * SXE-002: Configure link and activity LED to init state
+ * on driver load.
*/
subid = sp->pdev->subsystem_device;
if ((subid & 0xFF) >= 0x07) {
@@ -4864,13 +5522,61 @@
goto register_failed;
}
- /*
- * Make Link state as off at this point, when the Link change
- * interrupt comes the state will be automatically changed to
+ if (sp->device_type & XFRAME_II_DEVICE) {
+ DBG_PRINT(ERR_DBG, "%s: Neterion Xframe II 10GbE adapter ",
+ dev->name);
+ DBG_PRINT(ERR_DBG, "(rev %d), Driver %s\n",
+ get_xena_rev_id(sp->pdev),
+ s2io_driver_version);
+ DBG_PRINT(ERR_DBG, "MAC ADDR: %02x:%02x:%02x:%02x:%02x:%02x\n",
+ sp->def_mac_addr[0].mac_addr[0],
+ sp->def_mac_addr[0].mac_addr[1],
+ sp->def_mac_addr[0].mac_addr[2],
+ sp->def_mac_addr[0].mac_addr[3],
+ sp->def_mac_addr[0].mac_addr[4],
+ sp->def_mac_addr[0].mac_addr[5]);
+ mode = s2io_print_pci_mode(sp);
+ if (mode < 0) {
+ DBG_PRINT(ERR_DBG, " Unsupported PCI bus mode ");
+ ret = -EBADSLT;
+ goto set_swap_failed;
+ }
+ } else {
+ DBG_PRINT(ERR_DBG, "%s: Neterion Xframe I 10GbE adapter ",
+ dev->name);
+ DBG_PRINT(ERR_DBG, "(rev %d), Driver %s\n",
+ get_xena_rev_id(sp->pdev),
+ s2io_driver_version);
+ DBG_PRINT(ERR_DBG, "MAC ADDR: %02x:%02x:%02x:%02x:%02x:%02x\n",
+ sp->def_mac_addr[0].mac_addr[0],
+ sp->def_mac_addr[0].mac_addr[1],
+ sp->def_mac_addr[0].mac_addr[2],
+ sp->def_mac_addr[0].mac_addr[3],
+ sp->def_mac_addr[0].mac_addr[4],
+ sp->def_mac_addr[0].mac_addr[5]);
+ }
+
+ /* Initialize device name */
+ strcpy(sp->name, dev->name);
+ if (sp->device_type & XFRAME_II_DEVICE)
+ strcat(sp->name, ": Neterion Xframe II 10GbE adapter");
+ else
+ strcat(sp->name, ": Neterion Xframe I 10GbE adapter");
+
+ /* Initialize bimodal Interrupts */
+ sp->config.bimodal = bimodal;
+ if (!(sp->device_type & XFRAME_II_DEVICE) && bimodal) {
+ sp->config.bimodal = 0;
+ DBG_PRINT(ERR_DBG,"%s:Bimodal intr not supported by Xframe I\n",
+ dev->name);
+ }
+
+ /*
+ * Make Link state as off at this point, when the Link change
+ * interrupt comes the state will be automatically changed to
* the right state.
*/
netif_carrier_off(dev);
- sp->last_link_state = LINK_DOWN;
return 0;
@@ -4891,11 +5597,11 @@
}
/**
- * s2io_rem_nic - Free the PCI device
+ * s2io_rem_nic - Free the PCI device
* @pdev: structure containing the PCI related information of the device.
- * Description: This function is called by the Pci subsystem to release a
+ * Description: This function is called by the Pci subsystem to release a
* PCI device and free up all resource held up by the device. This could
- * be in response to a Hot plug event or when the driver is to be removed
+ * be in response to a Hot plug event or when the driver is to be removed
* from memory.
*/
@@ -4919,7 +5625,6 @@
pci_disable_device(pdev);
pci_release_regions(pdev);
pci_set_drvdata(pdev, NULL);
-
free_netdev(dev);
}
@@ -4935,11 +5640,11 @@
}
/**
- * s2io_closer - Cleanup routine for the driver
+ * s2io_closer - Cleanup routine for the driver
* Description: This function is the cleanup routine for the driver. It unregist * ers the driver.
*/
-static void s2io_closer(void)
+void s2io_closer(void)
{
pci_unregister_driver(&s2io_driver);
DBG_PRINT(INIT_DBG, "cleanup done\n");
diff --git a/drivers/net/s2io.h b/drivers/net/s2io.h
index 1711c8c..5d92707 100644
--- a/drivers/net/s2io.h
+++ b/drivers/net/s2io.h
@@ -31,6 +31,9 @@
#define SUCCESS 0
#define FAILURE -1
+/* Maximum time to flicker LED when asked to identify NIC using ethtool */
+#define MAX_FLICKER_TIME 60000 /* 60 Secs */
+
/* Maximum outstanding splits to be configured into xena. */
typedef enum xena_max_outstanding_splits {
XENA_ONE_SPLIT_TRANSACTION = 0,
@@ -45,10 +48,10 @@
#define XENA_MAX_OUTSTANDING_SPLITS(n) (n << 4)
/* OS concerned variables and constants */
-#define WATCH_DOG_TIMEOUT 5*HZ
-#define EFILL 0x1234
-#define ALIGN_SIZE 127
-#define PCIX_COMMAND_REGISTER 0x62
+#define WATCH_DOG_TIMEOUT 15*HZ
+#define EFILL 0x1234
+#define ALIGN_SIZE 127
+#define PCIX_COMMAND_REGISTER 0x62
/*
* Debug related variables.
@@ -61,7 +64,7 @@
#define INTR_DBG 4
/* Global variable that defines the present debug level of the driver. */
-static int debug_level = ERR_DBG; /* Default level. */
+int debug_level = ERR_DBG; /* Default level. */
/* DEBUG message print. */
#define DBG_PRINT(dbg_level, args...) if(!(debug_level<dbg_level)) printk(args)
@@ -71,6 +74,12 @@
#define L4_CKSUM_OK 0xFFFF
#define S2IO_JUMBO_SIZE 9600
+/* Driver statistics maintained by driver */
+typedef struct {
+ unsigned long long single_ecc_errs;
+ unsigned long long double_ecc_errs;
+} swStat_t;
+
/* The statistics block of Xena */
typedef struct stat_block {
/* Tx MAC statistics counters. */
@@ -186,12 +195,90 @@
u32 rxd_rd_cnt;
u32 rxf_wr_cnt;
u32 txf_rd_cnt;
+
+/* Tx MAC statistics overflow counters. */
+ u32 tmac_data_octets_oflow;
+ u32 tmac_frms_oflow;
+ u32 tmac_bcst_frms_oflow;
+ u32 tmac_mcst_frms_oflow;
+ u32 tmac_ucst_frms_oflow;
+ u32 tmac_ttl_octets_oflow;
+ u32 tmac_any_err_frms_oflow;
+ u32 tmac_nucst_frms_oflow;
+ u64 tmac_vlan_frms;
+ u32 tmac_drop_ip_oflow;
+ u32 tmac_vld_ip_oflow;
+ u32 tmac_rst_tcp_oflow;
+ u32 tmac_icmp_oflow;
+ u32 tpa_unknown_protocol;
+ u32 tmac_udp_oflow;
+ u32 reserved_10;
+ u32 tpa_parse_failure;
+
+/* Rx MAC Statistics overflow counters. */
+ u32 rmac_data_octets_oflow;
+ u32 rmac_vld_frms_oflow;
+ u32 rmac_vld_bcst_frms_oflow;
+ u32 rmac_vld_mcst_frms_oflow;
+ u32 rmac_accepted_ucst_frms_oflow;
+ u32 rmac_ttl_octets_oflow;
+ u32 rmac_discarded_frms_oflow;
+ u32 rmac_accepted_nucst_frms_oflow;
+ u32 rmac_usized_frms_oflow;
+ u32 rmac_drop_events_oflow;
+ u32 rmac_frag_frms_oflow;
+ u32 rmac_osized_frms_oflow;
+ u32 rmac_ip_oflow;
+ u32 rmac_jabber_frms_oflow;
+ u32 rmac_icmp_oflow;
+ u32 rmac_drop_ip_oflow;
+ u32 rmac_err_drp_udp_oflow;
+ u32 rmac_udp_oflow;
+ u32 reserved_11;
+ u32 rmac_pause_cnt_oflow;
+ u64 rmac_ttl_1519_4095_frms;
+ u64 rmac_ttl_4096_8191_frms;
+ u64 rmac_ttl_8192_max_frms;
+ u64 rmac_ttl_gt_max_frms;
+ u64 rmac_osized_alt_frms;
+ u64 rmac_jabber_alt_frms;
+ u64 rmac_gt_max_alt_frms;
+ u64 rmac_vlan_frms;
+ u32 rmac_len_discard;
+ u32 rmac_fcs_discard;
+ u32 rmac_pf_discard;
+ u32 rmac_da_discard;
+ u32 rmac_red_discard;
+ u32 rmac_rts_discard;
+ u32 reserved_12;
+ u32 rmac_ingm_full_discard;
+ u32 reserved_13;
+ u32 rmac_accepted_ip_oflow;
+ u32 reserved_14;
+ u32 link_fault_cnt;
+ swStat_t sw_stat;
} StatInfo_t;
-/* Structures representing different init time configuration
+/*
+ * Structures representing different init time configuration
* parameters of the NIC.
*/
+#define MAX_TX_FIFOS 8
+#define MAX_RX_RINGS 8
+
+/* FIFO mappings for all possible number of fifos configured */
+int fifo_map[][MAX_TX_FIFOS] = {
+ {0, 0, 0, 0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 1, 1, 1, 1},
+ {0, 0, 0, 1, 1, 1, 2, 2},
+ {0, 0, 1, 1, 2, 2, 3, 3},
+ {0, 0, 1, 1, 2, 2, 3, 4},
+ {0, 0, 1, 1, 2, 3, 4, 5},
+ {0, 0, 1, 2, 3, 4, 5, 6},
+ {0, 1, 2, 3, 4, 5, 6, 7},
+};
+
/* Maintains Per FIFO related information. */
typedef struct tx_fifo_config {
#define MAX_AVAILABLE_TXDS 8192
@@ -237,14 +324,14 @@
#define NO_SNOOP_RXD_BUFFER 0x02
} rx_ring_config_t;
-/* This structure provides contains values of the tunable parameters
- * of the H/W
+/* This structure provides contains values of the tunable parameters
+ * of the H/W
*/
struct config_param {
/* Tx Side */
u32 tx_fifo_num; /*Number of Tx FIFOs */
-#define MAX_TX_FIFOS 8
+ u8 fifo_mapping[MAX_TX_FIFOS];
tx_fifo_config_t tx_cfg[MAX_TX_FIFOS]; /*Per-Tx FIFO config */
u32 max_txds; /*Max no. of Tx buffer descriptor per TxDL */
u64 tx_intr_type;
@@ -252,10 +339,10 @@
/* Rx Side */
u32 rx_ring_num; /*Number of receive rings */
-#define MAX_RX_RINGS 8
#define MAX_RX_BLOCKS_PER_RING 150
rx_ring_config_t rx_cfg[MAX_RX_RINGS]; /*Per-Rx Ring config */
+ u8 bimodal; /*Flag for setting bimodal interrupts*/
#define HEADER_ETHERNET_II_802_3_SIZE 14
#define HEADER_802_2_SIZE 3
@@ -269,6 +356,7 @@
#define MAX_PYLD_JUMBO 9600
#define MAX_MTU_JUMBO (MAX_PYLD_JUMBO+18)
#define MAX_MTU_JUMBO_VLAN (MAX_PYLD_JUMBO+22)
+ u16 bus_speed;
};
/* Structure representing MAC Addrs */
@@ -277,7 +365,7 @@
} macaddr_t;
/* Structure that represent every FIFO element in the BAR1
- * Address location.
+ * Address location.
*/
typedef struct _TxFIFO_element {
u64 TxDL_Pointer;
@@ -339,6 +427,7 @@
#define RXD_FRAME_PROTO vBIT(0xFFFF,24,8)
#define RXD_FRAME_PROTO_IPV4 BIT(27)
#define RXD_FRAME_PROTO_IPV6 BIT(28)
+#define RXD_FRAME_IP_FRAG BIT(29)
#define RXD_FRAME_PROTO_TCP BIT(30)
#define RXD_FRAME_PROTO_UDP BIT(31)
#define TCP_OR_UDP_FRAME (RXD_FRAME_PROTO_TCP | RXD_FRAME_PROTO_UDP)
@@ -346,11 +435,15 @@
#define RXD_GET_L4_CKSUM(val) ((u16)(val) & 0xFFFF)
u64 Control_2;
+#define THE_RXD_MARK 0x3
+#define SET_RXD_MARKER vBIT(THE_RXD_MARK, 0, 2)
+#define GET_RXD_MARKER(ctrl) ((ctrl & SET_RXD_MARKER) >> 62)
+
#ifndef CONFIG_2BUFF_MODE
-#define MASK_BUFFER0_SIZE vBIT(0xFFFF,0,16)
-#define SET_BUFFER0_SIZE(val) vBIT(val,0,16)
+#define MASK_BUFFER0_SIZE vBIT(0x3FFF,2,14)
+#define SET_BUFFER0_SIZE(val) vBIT(val,2,14)
#else
-#define MASK_BUFFER0_SIZE vBIT(0xFF,0,16)
+#define MASK_BUFFER0_SIZE vBIT(0xFF,2,14)
#define MASK_BUFFER1_SIZE vBIT(0xFFFF,16,16)
#define MASK_BUFFER2_SIZE vBIT(0xFFFF,32,16)
#define SET_BUFFER0_SIZE(val) vBIT(val,8,8)
@@ -363,7 +456,7 @@
#define SET_NUM_TAG(val) vBIT(val,16,32)
#ifndef CONFIG_2BUFF_MODE
-#define RXD_GET_BUFFER0_SIZE(Control_2) (u64)((Control_2 & vBIT(0xFFFF,0,16)))
+#define RXD_GET_BUFFER0_SIZE(Control_2) (u64)((Control_2 & vBIT(0x3FFF,2,14)))
#else
#define RXD_GET_BUFFER0_SIZE(Control_2) (u8)((Control_2 & MASK_BUFFER0_SIZE) \
>> 48)
@@ -382,7 +475,7 @@
#endif
} RxD_t;
-/* Structure that represents the Rx descriptor block which contains
+/* Structure that represents the Rx descriptor block which contains
* 128 Rx descriptors.
*/
#ifndef CONFIG_2BUFF_MODE
@@ -392,11 +485,11 @@
u64 reserved_0;
#define END_OF_BLOCK 0xFEFFFFFFFFFFFFFFULL
- u64 reserved_1; /* 0xFEFFFFFFFFFFFFFF to mark last
+ u64 reserved_1; /* 0xFEFFFFFFFFFFFFFF to mark last
* Rxd in this blk */
u64 reserved_2_pNext_RxD_block; /* Logical ptr to next */
u64 pNext_RxD_Blk_physical; /* Buff0_ptr.In a 32 bit arch
- * the upper 32 bits should
+ * the upper 32 bits should
* be 0 */
} RxD_block_t;
#else
@@ -405,13 +498,13 @@
RxD_t rxd[MAX_RXDS_PER_BLOCK];
#define END_OF_BLOCK 0xFEFFFFFFFFFFFFFFULL
- u64 reserved_1; /* 0xFEFFFFFFFFFFFFFF to mark last Rxd
+ u64 reserved_1; /* 0xFEFFFFFFFFFFFFFF to mark last Rxd
* in this blk */
u64 pNext_RxD_Blk_physical; /* Phy ponter to next blk. */
} RxD_block_t;
#define SIZE_OF_BLOCK 4096
-/* Structure to hold virtual addresses of Buf0 and Buf1 in
+/* Structure to hold virtual addresses of Buf0 and Buf1 in
* 2buf mode. */
typedef struct bufAdd {
void *ba_0_org;
@@ -423,8 +516,8 @@
/* Structure which stores all the MAC control parameters */
-/* This structure stores the offset of the RxD in the ring
- * from which the Rx Interrupt processor can start picking
+/* This structure stores the offset of the RxD in the ring
+ * from which the Rx Interrupt processor can start picking
* up the RxDs for processing.
*/
typedef struct _rx_curr_get_info_t {
@@ -436,7 +529,7 @@
typedef rx_curr_get_info_t rx_curr_put_info_t;
/* This structure stores the offset of the TxDl in the FIFO
- * from which the Tx Interrupt processor can start picking
+ * from which the Tx Interrupt processor can start picking
* up the TxDLs for send complete interrupt processing.
*/
typedef struct {
@@ -446,32 +539,96 @@
typedef tx_curr_get_info_t tx_curr_put_info_t;
+/* Structure that holds the Phy and virt addresses of the Blocks */
+typedef struct rx_block_info {
+ RxD_t *block_virt_addr;
+ dma_addr_t block_dma_addr;
+} rx_block_info_t;
+
+/* pre declaration of the nic structure */
+typedef struct s2io_nic nic_t;
+
+/* Ring specific structure */
+typedef struct ring_info {
+ /* The ring number */
+ int ring_no;
+
+ /*
+ * Place holders for the virtual and physical addresses of
+ * all the Rx Blocks
+ */
+ rx_block_info_t rx_blocks[MAX_RX_BLOCKS_PER_RING];
+ int block_count;
+ int pkt_cnt;
+
+ /*
+ * Put pointer info which indictes which RxD has to be replenished
+ * with a new buffer.
+ */
+ rx_curr_put_info_t rx_curr_put_info;
+
+ /*
+ * Get pointer info which indictes which is the last RxD that was
+ * processed by the driver.
+ */
+ rx_curr_get_info_t rx_curr_get_info;
+
+#ifndef CONFIG_S2IO_NAPI
+ /* Index to the absolute position of the put pointer of Rx ring */
+ int put_pos;
+#endif
+
+#ifdef CONFIG_2BUFF_MODE
+ /* Buffer Address store. */
+ buffAdd_t **ba;
+#endif
+ nic_t *nic;
+} ring_info_t;
+
+/* Fifo specific structure */
+typedef struct fifo_info {
+ /* FIFO number */
+ int fifo_no;
+
+ /* Maximum TxDs per TxDL */
+ int max_txds;
+
+ /* Place holder of all the TX List's Phy and Virt addresses. */
+ list_info_hold_t *list_info;
+
+ /*
+ * Current offset within the tx FIFO where driver would write
+ * new Tx frame
+ */
+ tx_curr_put_info_t tx_curr_put_info;
+
+ /*
+ * Current offset within tx FIFO from where the driver would start freeing
+ * the buffers
+ */
+ tx_curr_get_info_t tx_curr_get_info;
+
+ nic_t *nic;
+}fifo_info_t;
+
/* Infomation related to the Tx and Rx FIFOs and Rings of Xena
* is maintained in this structure.
*/
typedef struct mac_info {
-/* rx side stuff */
- /* Put pointer info which indictes which RxD has to be replenished
- * with a new buffer.
- */
- rx_curr_put_info_t rx_curr_put_info[MAX_RX_RINGS];
-
- /* Get pointer info which indictes which is the last RxD that was
- * processed by the driver.
- */
- rx_curr_get_info_t rx_curr_get_info[MAX_RX_RINGS];
-
- u16 rmac_pause_time;
- u16 mc_pause_threshold_q0q3;
- u16 mc_pause_threshold_q4q7;
-
/* tx side stuff */
/* logical pointer of start of each Tx FIFO */
TxFIFO_element_t __iomem *tx_FIFO_start[MAX_TX_FIFOS];
-/* Current offset within tx_FIFO_start, where driver would write new Tx frame*/
- tx_curr_put_info_t tx_curr_put_info[MAX_TX_FIFOS];
- tx_curr_get_info_t tx_curr_get_info[MAX_TX_FIFOS];
+ /* Fifo specific structure */
+ fifo_info_t fifos[MAX_TX_FIFOS];
+
+/* rx side stuff */
+ /* Ring specific structure */
+ ring_info_t rings[MAX_RX_RINGS];
+
+ u16 rmac_pause_time;
+ u16 mc_pause_threshold_q0q3;
+ u16 mc_pause_threshold_q4q7;
void *stats_mem; /* orignal pointer to allocated mem */
dma_addr_t stats_mem_phy; /* Physical address of the stat block */
@@ -485,12 +642,6 @@
int usage_cnt;
} usr_addr_t;
-/* Structure that holds the Phy and virt addresses of the Blocks */
-typedef struct rx_block_info {
- RxD_t *block_virt_addr;
- dma_addr_t block_dma_addr;
-} rx_block_info_t;
-
/* Default Tunable parameters of the NIC. */
#define DEFAULT_FIFO_LEN 4096
#define SMALL_RXD_CNT 30 * (MAX_RXDS_PER_BLOCK+1)
@@ -499,7 +650,20 @@
#define LARGE_BLK_CNT 100
/* Structure representing one instance of the NIC */
-typedef struct s2io_nic {
+struct s2io_nic {
+#ifdef CONFIG_S2IO_NAPI
+ /*
+ * Count of packets to be processed in a given iteration, it will be indicated
+ * by the quota field of the device structure when NAPI is enabled.
+ */
+ int pkts_to_process;
+#endif
+ struct net_device *dev;
+ mac_info_t mac_control;
+ struct config_param config;
+ struct pci_dev *pdev;
+ void __iomem *bar0;
+ void __iomem *bar1;
#define MAX_MAC_SUPPORTED 16
#define MAX_SUPPORTED_MULTICASTS MAX_MAC_SUPPORTED
@@ -507,33 +671,20 @@
macaddr_t pre_mac_addr[MAX_MAC_SUPPORTED];
struct net_device_stats stats;
- void __iomem *bar0;
- void __iomem *bar1;
- struct config_param config;
- mac_info_t mac_control;
int high_dma_flag;
int device_close_flag;
int device_enabled_once;
- char name[32];
+ char name[50];
struct tasklet_struct task;
volatile unsigned long tasklet_status;
- struct timer_list timer;
- struct net_device *dev;
- struct pci_dev *pdev;
- u16 vendor_id;
- u16 device_id;
- u16 ccmd;
- u32 cbar0_1;
- u32 cbar0_2;
- u32 cbar1_1;
- u32 cbar1_2;
- u32 cirq;
- u8 cache_line;
- u32 rom_expansion;
- u16 pcix_cmd;
- u32 irq;
+ /* Timer that handles I/O errors/exceptions */
+ struct timer_list alarm_timer;
+
+ /* Space to back up the PCI config space */
+ u32 config_space[256 / sizeof(u32)];
+
atomic_t rx_bufs_left[MAX_RX_RINGS];
spinlock_t tx_lock;
@@ -558,27 +709,11 @@
u16 tx_err_count;
u16 rx_err_count;
-#ifndef CONFIG_S2IO_NAPI
- /* Index to the absolute position of the put pointer of Rx ring. */
- int put_pos[MAX_RX_RINGS];
-#endif
-
- /*
- * Place holders for the virtual and physical addresses of
- * all the Rx Blocks
- */
- rx_block_info_t rx_blocks[MAX_RX_RINGS][MAX_RX_BLOCKS_PER_RING];
- int block_count[MAX_RX_RINGS];
- int pkt_cnt[MAX_RX_RINGS];
-
- /* Place holder of all the TX List's Phy and Virt addresses. */
- list_info_hold_t *list_info[MAX_TX_FIFOS];
-
/* Id timer, used to blink NIC to physically identify NIC. */
struct timer_list id_timer;
/* Restart timer, used to restart NIC if the device is stuck and
- * a schedule task that will set the correct Link state once the
+ * a schedule task that will set the correct Link state once the
* NIC's PHY has stabilized after a state change.
*/
#ifdef INIT_TQUEUE
@@ -589,12 +724,12 @@
struct work_struct set_link_task;
#endif
- /* Flag that can be used to turn on or turn off the Rx checksum
+ /* Flag that can be used to turn on or turn off the Rx checksum
* offload feature.
*/
int rx_csum;
- /* after blink, the adapter must be restored with original
+ /* after blink, the adapter must be restored with original
* values.
*/
u64 adapt_ctrl_org;
@@ -604,16 +739,19 @@
#define LINK_DOWN 1
#define LINK_UP 2
-#ifdef CONFIG_2BUFF_MODE
- /* Buffer Address store. */
- buffAdd_t **ba[MAX_RX_RINGS];
-#endif
int task_flag;
#define CARD_DOWN 1
#define CARD_UP 2
atomic_t card_state;
volatile unsigned long link_state;
-} nic_t;
+ struct vlan_group *vlgrp;
+#define XFRAME_I_DEVICE 1
+#define XFRAME_II_DEVICE 2
+ u8 device_type;
+
+ spinlock_t rx_lock;
+ atomic_t isr_cnt;
+};
#define RESET_ERROR 1;
#define CMD_ERROR 2;
@@ -622,9 +760,10 @@
#ifndef readq
static inline u64 readq(void __iomem *addr)
{
- u64 ret = readl(addr + 4);
- ret <<= 32;
- ret |= readl(addr);
+ u64 ret = 0;
+ ret = readl(addr + 4);
+ (u64) ret <<= 32;
+ (u64) ret |= readl(addr);
return ret;
}
@@ -637,10 +776,10 @@
writel((u32) (val >> 32), (addr + 4));
}
-/* In 32 bit modes, some registers have to be written in a
+/* In 32 bit modes, some registers have to be written in a
* particular order to expect correct hardware operation. The
- * macro SPECIAL_REG_WRITE is used to perform such ordered
- * writes. Defines UF (Upper First) and LF (Lower First) will
+ * macro SPECIAL_REG_WRITE is used to perform such ordered
+ * writes. Defines UF (Upper First) and LF (Lower First) will
* be used to specify the required write order.
*/
#define UF 1
@@ -716,6 +855,7 @@
#define PCC_FB_ECC_ERR vBIT(0xff, 16, 8) /* Interrupt to indicate
PCC_FB_ECC Error. */
+#define RXD_GET_VLAN_TAG(Control_2) (u16)(Control_2 & MASK_VLAN_TAG)
/*
* Prototype declaration.
*/
@@ -725,36 +865,30 @@
static int init_shared_mem(struct s2io_nic *sp);
static void free_shared_mem(struct s2io_nic *sp);
static int init_nic(struct s2io_nic *nic);
-#ifndef CONFIG_S2IO_NAPI
-static void rx_intr_handler(struct s2io_nic *sp);
-#endif
-static void tx_intr_handler(struct s2io_nic *sp);
+static void rx_intr_handler(ring_info_t *ring_data);
+static void tx_intr_handler(fifo_info_t *fifo_data);
static void alarm_intr_handler(struct s2io_nic *sp);
static int s2io_starter(void);
-static void s2io_closer(void);
+void s2io_closer(void);
static void s2io_tx_watchdog(struct net_device *dev);
static void s2io_tasklet(unsigned long dev_addr);
static void s2io_set_multicast(struct net_device *dev);
-#ifndef CONFIG_2BUFF_MODE
-static int rx_osm_handler(nic_t * sp, u16 len, RxD_t * rxdp, int ring_no);
-#else
-static int rx_osm_handler(nic_t * sp, RxD_t * rxdp, int ring_no,
- buffAdd_t * ba);
-#endif
-static void s2io_link(nic_t * sp, int link);
-static void s2io_reset(nic_t * sp);
-#ifdef CONFIG_S2IO_NAPI
+static int rx_osm_handler(ring_info_t *ring_data, RxD_t * rxdp);
+void s2io_link(nic_t * sp, int link);
+void s2io_reset(nic_t * sp);
+#if defined(CONFIG_S2IO_NAPI)
static int s2io_poll(struct net_device *dev, int *budget);
#endif
static void s2io_init_pci(nic_t * sp);
-static int s2io_set_mac_addr(struct net_device *dev, u8 * addr);
+int s2io_set_mac_addr(struct net_device *dev, u8 * addr);
+static void s2io_alarm_handle(unsigned long data);
static irqreturn_t s2io_isr(int irq, void *dev_id, struct pt_regs *regs);
-static int verify_xena_quiescence(u64 val64, int flag);
+static int verify_xena_quiescence(nic_t *sp, u64 val64, int flag);
static struct ethtool_ops netdev_ethtool_ops;
static void s2io_set_link(unsigned long data);
-static int s2io_set_swapper(nic_t * sp);
-static void s2io_card_down(nic_t * nic);
-static int s2io_card_up(nic_t * nic);
-
+int s2io_set_swapper(nic_t * sp);
+static void s2io_card_down(nic_t *nic);
+static int s2io_card_up(nic_t *nic);
+int get_xena_rev_id(struct pci_dev *pdev);
#endif /* _S2IO_H */
diff --git a/drivers/net/skge.c b/drivers/net/skge.c
index f157394..d7c9851 100644
--- a/drivers/net/skge.c
+++ b/drivers/net/skge.c
@@ -42,7 +42,7 @@
#include "skge.h"
#define DRV_NAME "skge"
-#define DRV_VERSION "0.8"
+#define DRV_VERSION "0.9"
#define PFX DRV_NAME " "
#define DEFAULT_TX_RING_SIZE 128
@@ -79,8 +79,8 @@
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4320) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x5005) }, /* Belkin */
{ PCI_DEVICE(PCI_VENDOR_ID_CNET, PCI_DEVICE_ID_CNET_GIGACARD) },
- { PCI_DEVICE(PCI_VENDOR_ID_LINKSYS, PCI_DEVICE_ID_LINKSYS_EG1032) },
{ PCI_DEVICE(PCI_VENDOR_ID_LINKSYS, PCI_DEVICE_ID_LINKSYS_EG1064) },
+ { PCI_VENDOR_ID_LINKSYS, 0x1032, PCI_ANY_ID, 0x0015, },
{ 0 }
};
MODULE_DEVICE_TABLE(pci, skge_id_table);
@@ -189,7 +189,7 @@
{
u32 supported;
- if (iscopper(hw)) {
+ if (hw->copper) {
supported = SUPPORTED_10baseT_Half
| SUPPORTED_10baseT_Full
| SUPPORTED_100baseT_Half
@@ -222,7 +222,7 @@
ecmd->transceiver = XCVR_INTERNAL;
ecmd->supported = skge_supported_modes(hw);
- if (iscopper(hw)) {
+ if (hw->copper) {
ecmd->port = PORT_TP;
ecmd->phy_address = hw->phy_addr;
} else
@@ -876,6 +876,9 @@
static void skge_link_up(struct skge_port *skge)
{
+ skge_write8(skge->hw, SK_REG(skge->port, LNK_LED_REG),
+ LED_BLK_OFF|LED_SYNC_OFF|LED_ON);
+
netif_carrier_on(skge->netdev);
if (skge->tx_avail > MAX_SKB_FRAGS + 1)
netif_wake_queue(skge->netdev);
@@ -894,6 +897,7 @@
static void skge_link_down(struct skge_port *skge)
{
+ skge_write8(skge->hw, SK_REG(skge->port, LNK_LED_REG), LED_OFF);
netif_carrier_off(skge->netdev);
netif_stop_queue(skge->netdev);
@@ -1599,7 +1603,7 @@
adv = PHY_AN_CSMA;
if (skge->autoneg == AUTONEG_ENABLE) {
- if (iscopper(hw)) {
+ if (hw->copper) {
if (skge->advertising & ADVERTISED_1000baseT_Full)
ct1000 |= PHY_M_1000C_AFD;
if (skge->advertising & ADVERTISED_1000baseT_Half)
@@ -1691,7 +1695,7 @@
/* Set hardware config mode */
reg = GPC_INT_POL_HI | GPC_DIS_FC | GPC_DIS_SLEEP |
GPC_ENA_XC | GPC_ANEG_ADV_ALL_M | GPC_ENA_PAUSE;
- reg |= iscopper(hw) ? GPC_HWCFG_GMII_COP : GPC_HWCFG_GMII_FIB;
+ reg |= hw->copper ? GPC_HWCFG_GMII_COP : GPC_HWCFG_GMII_FIB;
/* Clear GMC reset */
skge_write32(hw, SK_REG(port, GPHY_CTRL), reg | GPC_RST_SET);
@@ -1780,7 +1784,12 @@
reg &= ~GMF_RX_F_FL_ON;
skge_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_CLR);
skge_write16(hw, SK_REG(port, RX_GMF_CTRL_T), reg);
- skge_write16(hw, SK_REG(port, RX_GMF_FL_THR), RX_GMF_FL_THR_DEF);
+ /*
+ * because Pause Packet Truncation in GMAC is not working
+ * we have to increase the Flush Threshold to 64 bytes
+ * in order to flush pause packets in Rx FIFO on Yukon-1
+ */
+ skge_write16(hw, SK_REG(port, RX_GMF_FL_THR), RX_GMF_FL_THR_DEF+1);
/* Configure Tx MAC FIFO */
skge_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_CLR);
@@ -2670,18 +2679,6 @@
/* Timestamp (unused) overflow */
if (hwstatus & IS_IRQ_TIST_OV)
skge_write8(hw, GMAC_TI_ST_CTRL, GMT_ST_CLR_IRQ);
-
- if (hwstatus & IS_IRQ_SENSOR) {
- /* no sensors on 32-bit Yukon */
- if (!(skge_read16(hw, B0_CTST) & CS_BUS_SLOT_SZ)) {
- printk(KERN_ERR PFX "ignoring bogus sensor interrups\n");
- skge_write32(hw, B0_HWE_IMSK,
- IS_ERR_MSK & ~IS_IRQ_SENSOR);
- } else
- printk(KERN_WARNING PFX "sensor interrupt\n");
- }
-
-
}
if (hwstatus & IS_RAM_RD_PAR) {
@@ -2712,9 +2709,10 @@
skge_pci_clear(hw);
+ /* if error still set then just ignore it */
hwstatus = skge_read32(hw, B0_HWE_ISRC);
if (hwstatus & IS_IRQ_STAT) {
- printk(KERN_WARNING PFX "IRQ status %x: still set ignoring hardware errors\n",
+ pr_debug("IRQ status %x: still set ignoring hardware errors\n",
hwstatus);
hw->intr_mask &= ~IS_HW_ERR;
}
@@ -2876,7 +2874,7 @@
static int skge_reset(struct skge_hw *hw)
{
u16 ctst;
- u8 t8, mac_cfg;
+ u8 t8, mac_cfg, pmd_type, phy_type;
int i;
ctst = skge_read16(hw, B0_CTST);
@@ -2895,18 +2893,19 @@
ctst & (CS_CLK_RUN_HOT|CS_CLK_RUN_RST|CS_CLK_RUN_ENA));
hw->chip_id = skge_read8(hw, B2_CHIP_ID);
- hw->phy_type = skge_read8(hw, B2_E_1) & 0xf;
- hw->pmd_type = skge_read8(hw, B2_PMD_TYP);
+ phy_type = skge_read8(hw, B2_E_1) & 0xf;
+ pmd_type = skge_read8(hw, B2_PMD_TYP);
+ hw->copper = (pmd_type == 'T' || pmd_type == '1');
switch (hw->chip_id) {
case CHIP_ID_GENESIS:
- switch (hw->phy_type) {
+ switch (phy_type) {
case SK_PHY_BCOM:
hw->phy_addr = PHY_ADDR_BCOM;
break;
default:
printk(KERN_ERR PFX "%s: unsupported phy type 0x%x\n",
- pci_name(hw->pdev), hw->phy_type);
+ pci_name(hw->pdev), phy_type);
return -EOPNOTSUPP;
}
break;
@@ -2914,13 +2913,10 @@
case CHIP_ID_YUKON:
case CHIP_ID_YUKON_LITE:
case CHIP_ID_YUKON_LP:
- if (hw->phy_type < SK_PHY_MARV_COPPER && hw->pmd_type != 'S')
- hw->phy_type = SK_PHY_MARV_COPPER;
+ if (phy_type < SK_PHY_MARV_COPPER && pmd_type != 'S')
+ hw->copper = 1;
hw->phy_addr = PHY_ADDR_MARV;
- if (!iscopper(hw))
- hw->phy_type = SK_PHY_MARV_FIBER;
-
break;
default:
@@ -2948,12 +2944,20 @@
else
hw->ram_size = t8 * 4096;
+ hw->intr_mask = IS_HW_ERR | IS_EXT_REG;
if (hw->chip_id == CHIP_ID_GENESIS)
genesis_init(hw);
else {
/* switch power to VCC (WA for VAUX problem) */
skge_write8(hw, B0_POWER_CTRL,
PC_VAUX_ENA | PC_VCC_ENA | PC_VAUX_OFF | PC_VCC_ON);
+ /* avoid boards with stuck Hardware error bits */
+ if ((skge_read32(hw, B0_ISRC) & IS_HW_ERR) &&
+ (skge_read32(hw, B0_HWE_ISRC) & IS_IRQ_SENSOR)) {
+ printk(KERN_WARNING PFX "stuck hardware sensor bit\n");
+ hw->intr_mask &= ~IS_HW_ERR;
+ }
+
for (i = 0; i < hw->ports; i++) {
skge_write16(hw, SK_REG(i, GMAC_LINK_CTRL), GMLC_RST_SET);
skge_write16(hw, SK_REG(i, GMAC_LINK_CTRL), GMLC_RST_CLR);
@@ -2994,7 +2998,6 @@
skge_write32(hw, B2_IRQM_INI, skge_usecs2clk(hw, 100));
skge_write32(hw, B2_IRQM_CTRL, TIM_START);
- hw->intr_mask = IS_HW_ERR | IS_EXT_REG;
skge_write32(hw, B0_IMSK, hw->intr_mask);
if (hw->chip_id != CHIP_ID_GENESIS)
diff --git a/drivers/net/skge.h b/drivers/net/skge.h
index b432f1b..f1680be 100644
--- a/drivers/net/skge.h
+++ b/drivers/net/skge.h
@@ -214,8 +214,6 @@
/* B2_IRQM_HWE_MSK 32 bit IRQ Moderation HW Error Mask */
enum {
- IS_ERR_MSK = 0x00003fff,/* All Error bits */
-
IS_IRQ_TIST_OV = 1<<13, /* Time Stamp Timer Overflow (YUKON only) */
IS_IRQ_SENSOR = 1<<12, /* IRQ from Sensor (YUKON only) */
IS_IRQ_MST_ERR = 1<<11, /* IRQ master error detected */
@@ -230,6 +228,12 @@
IS_M2_PAR_ERR = 1<<2, /* MAC 2 Parity Error */
IS_R1_PAR_ERR = 1<<1, /* Queue R1 Parity Error */
IS_R2_PAR_ERR = 1<<0, /* Queue R2 Parity Error */
+
+ IS_ERR_MSK = IS_IRQ_MST_ERR | IS_IRQ_STAT
+ | IS_NO_STAT_M1 | IS_NO_STAT_M2
+ | IS_RAM_RD_PAR | IS_RAM_WR_PAR
+ | IS_M1_PAR_ERR | IS_M2_PAR_ERR
+ | IS_R1_PAR_ERR | IS_R2_PAR_ERR,
};
/* B2_TST_CTRL1 8 bit Test Control Register 1 */
@@ -2456,24 +2460,17 @@
u8 chip_id;
u8 chip_rev;
- u8 phy_type;
- u8 pmd_type;
- u16 phy_addr;
+ u8 copper;
u8 ports;
u32 ram_size;
u32 ram_offset;
+ u16 phy_addr;
struct tasklet_struct ext_tasklet;
spinlock_t phy_lock;
};
-
-static inline int iscopper(const struct skge_hw *hw)
-{
- return (hw->pmd_type == 'T');
-}
-
enum {
FLOW_MODE_NONE = 0, /* No Flow-Control */
FLOW_MODE_LOC_SEND = 1, /* Local station sends PAUSE */
diff --git a/drivers/net/smc-ultra.c b/drivers/net/smc-ultra.c
index 6d9dae6..ba8593ac 100644
--- a/drivers/net/smc-ultra.c
+++ b/drivers/net/smc-ultra.c
@@ -68,6 +68,7 @@
#include <linux/etherdevice.h>
#include <asm/io.h>
+#include <asm/irq.h>
#include <asm/system.h>
#include "8390.h"
diff --git a/drivers/net/sonic.c b/drivers/net/sonic.c
index cdc9cc8..90b818a 100644
--- a/drivers/net/sonic.c
+++ b/drivers/net/sonic.c
@@ -1,6 +1,11 @@
/*
* sonic.c
*
+ * (C) 2005 Finn Thain
+ *
+ * Converted to DMA API, added zero-copy buffer handling, and
+ * (from the mac68k project) introduced dhd's support for 16-bit cards.
+ *
* (C) 1996,1998 by Thomas Bogendoerfer (tsbogend@alpha.franken.de)
*
* This driver is based on work from Andreas Busse, but most of
@@ -9,12 +14,23 @@
* (C) 1995 by Andreas Busse (andy@waldorf-gmbh.de)
*
* Core code included by system sonic drivers
+ *
+ * And... partially rewritten again by David Huggins-Daines in order
+ * to cope with screwed up Macintosh NICs that may or may not use
+ * 16-bit DMA.
+ *
+ * (C) 1999 David Huggins-Daines <dhd@debian.org>
+ *
*/
/*
* Sources: Olivetti M700-10 Risc Personal Computer hardware handbook,
* National Semiconductors data sheet for the DP83932B Sonic Ethernet
* controller, and the files "8390.c" and "skeleton.c" in this directory.
+ *
+ * Additional sources: Nat Semi data sheet for the DP83932C and Nat Semi
+ * Application Note AN-746, the files "lance.c" and "ibmlana.c". See also
+ * the NetBSD file "sys/arch/mac68k/dev/if_sn.c".
*/
@@ -28,6 +44,9 @@
*/
static int sonic_open(struct net_device *dev)
{
+ struct sonic_local *lp = netdev_priv(dev);
+ int i;
+
if (sonic_debug > 2)
printk("sonic_open: initializing sonic driver.\n");
@@ -40,14 +59,59 @@
* This means that during execution of the handler interrupt are disabled
* covering another bug otherwise corrupting data. This doesn't mean
* this glue works ok under all situations.
+ *
+ * Note (dhd): this also appears to prevent lockups on the Macintrash
+ * when more than one Ethernet card is installed (knock on wood)
+ *
+ * Note (fthain): whether the above is still true is anyones guess. Certainly
+ * the buffer handling algorithms will not tolerate re-entrance without some
+ * mutual exclusion added. Anyway, the memcpy has now been eliminated from the
+ * rx code to make this a faster "fast interrupt".
*/
-// if (sonic_request_irq(dev->irq, &sonic_interrupt, 0, "sonic", dev)) {
- if (sonic_request_irq(dev->irq, &sonic_interrupt, SA_INTERRUPT,
- "sonic", dev)) {
- printk("\n%s: unable to get IRQ %d .\n", dev->name, dev->irq);
+ if (request_irq(dev->irq, &sonic_interrupt, SONIC_IRQ_FLAG, "sonic", dev)) {
+ printk(KERN_ERR "\n%s: unable to get IRQ %d .\n", dev->name, dev->irq);
return -EAGAIN;
}
+ for (i = 0; i < SONIC_NUM_RRS; i++) {
+ struct sk_buff *skb = dev_alloc_skb(SONIC_RBSIZE + 2);
+ if (skb == NULL) {
+ while(i > 0) { /* free any that were allocated successfully */
+ i--;
+ dev_kfree_skb(lp->rx_skb[i]);
+ lp->rx_skb[i] = NULL;
+ }
+ printk(KERN_ERR "%s: couldn't allocate receive buffers\n",
+ dev->name);
+ return -ENOMEM;
+ }
+ skb->dev = dev;
+ /* align IP header unless DMA requires otherwise */
+ if (SONIC_BUS_SCALE(lp->dma_bitmode) == 2)
+ skb_reserve(skb, 2);
+ lp->rx_skb[i] = skb;
+ }
+
+ for (i = 0; i < SONIC_NUM_RRS; i++) {
+ dma_addr_t laddr = dma_map_single(lp->device, skb_put(lp->rx_skb[i], SONIC_RBSIZE),
+ SONIC_RBSIZE, DMA_FROM_DEVICE);
+ if (!laddr) {
+ while(i > 0) { /* free any that were mapped successfully */
+ i--;
+ dma_unmap_single(lp->device, lp->rx_laddr[i], SONIC_RBSIZE, DMA_FROM_DEVICE);
+ lp->rx_laddr[i] = (dma_addr_t)0;
+ }
+ for (i = 0; i < SONIC_NUM_RRS; i++) {
+ dev_kfree_skb(lp->rx_skb[i]);
+ lp->rx_skb[i] = NULL;
+ }
+ printk(KERN_ERR "%s: couldn't map rx DMA buffers\n",
+ dev->name);
+ return -ENOMEM;
+ }
+ lp->rx_laddr[i] = laddr;
+ }
+
/*
* Initialize the SONIC
*/
@@ -67,7 +131,8 @@
*/
static int sonic_close(struct net_device *dev)
{
- unsigned int base_addr = dev->base_addr;
+ struct sonic_local *lp = netdev_priv(dev);
+ int i;
if (sonic_debug > 2)
printk("sonic_close\n");
@@ -77,20 +142,56 @@
/*
* stop the SONIC, disable interrupts
*/
- SONIC_WRITE(SONIC_ISR, 0x7fff);
SONIC_WRITE(SONIC_IMR, 0);
+ SONIC_WRITE(SONIC_ISR, 0x7fff);
SONIC_WRITE(SONIC_CMD, SONIC_CR_RST);
- sonic_free_irq(dev->irq, dev); /* release the IRQ */
+ /* unmap and free skbs that haven't been transmitted */
+ for (i = 0; i < SONIC_NUM_TDS; i++) {
+ if(lp->tx_laddr[i]) {
+ dma_unmap_single(lp->device, lp->tx_laddr[i], lp->tx_len[i], DMA_TO_DEVICE);
+ lp->tx_laddr[i] = (dma_addr_t)0;
+ }
+ if(lp->tx_skb[i]) {
+ dev_kfree_skb(lp->tx_skb[i]);
+ lp->tx_skb[i] = NULL;
+ }
+ }
+
+ /* unmap and free the receive buffers */
+ for (i = 0; i < SONIC_NUM_RRS; i++) {
+ if(lp->rx_laddr[i]) {
+ dma_unmap_single(lp->device, lp->rx_laddr[i], SONIC_RBSIZE, DMA_FROM_DEVICE);
+ lp->rx_laddr[i] = (dma_addr_t)0;
+ }
+ if(lp->rx_skb[i]) {
+ dev_kfree_skb(lp->rx_skb[i]);
+ lp->rx_skb[i] = NULL;
+ }
+ }
+
+ free_irq(dev->irq, dev); /* release the IRQ */
return 0;
}
static void sonic_tx_timeout(struct net_device *dev)
{
- struct sonic_local *lp = (struct sonic_local *) dev->priv;
- printk("%s: transmit timed out.\n", dev->name);
-
+ struct sonic_local *lp = netdev_priv(dev);
+ int i;
+ /* Stop the interrupts for this */
+ SONIC_WRITE(SONIC_IMR, 0);
+ /* We could resend the original skbs. Easier to re-initialise. */
+ for (i = 0; i < SONIC_NUM_TDS; i++) {
+ if(lp->tx_laddr[i]) {
+ dma_unmap_single(lp->device, lp->tx_laddr[i], lp->tx_len[i], DMA_TO_DEVICE);
+ lp->tx_laddr[i] = (dma_addr_t)0;
+ }
+ if(lp->tx_skb[i]) {
+ dev_kfree_skb(lp->tx_skb[i]);
+ lp->tx_skb[i] = NULL;
+ }
+ }
/* Try to restart the adaptor. */
sonic_init(dev);
lp->stats.tx_errors++;
@@ -100,60 +201,92 @@
/*
* transmit packet
+ *
+ * Appends new TD during transmission thus avoiding any TX interrupts
+ * until we run out of TDs.
+ * This routine interacts closely with the ISR in that it may,
+ * set tx_skb[i]
+ * reset the status flags of the new TD
+ * set and reset EOL flags
+ * stop the tx queue
+ * The ISR interacts with this routine in various ways. It may,
+ * reset tx_skb[i]
+ * test the EOL and status flags of the TDs
+ * wake the tx queue
+ * Concurrently with all of this, the SONIC is potentially writing to
+ * the status flags of the TDs.
+ * Until some mutual exclusion is added, this code will not work with SMP. However,
+ * MIPS Jazz machines and m68k Macs were all uni-processor machines.
*/
+
static int sonic_send_packet(struct sk_buff *skb, struct net_device *dev)
{
- struct sonic_local *lp = (struct sonic_local *) dev->priv;
- unsigned int base_addr = dev->base_addr;
- unsigned int laddr;
- int entry, length;
-
- netif_stop_queue(dev);
+ struct sonic_local *lp = netdev_priv(dev);
+ dma_addr_t laddr;
+ int length;
+ int entry = lp->next_tx;
if (sonic_debug > 2)
printk("sonic_send_packet: skb=%p, dev=%p\n", skb, dev);
+ length = skb->len;
+ if (length < ETH_ZLEN) {
+ skb = skb_padto(skb, ETH_ZLEN);
+ if (skb == NULL)
+ return 0;
+ length = ETH_ZLEN;
+ }
+
/*
* Map the packet data into the logical DMA address space
*/
- if ((laddr = vdma_alloc(CPHYSADDR(skb->data), skb->len)) == ~0UL) {
- printk("%s: no VDMA entry for transmit available.\n",
- dev->name);
+
+ laddr = dma_map_single(lp->device, skb->data, length, DMA_TO_DEVICE);
+ if (!laddr) {
+ printk(KERN_ERR "%s: failed to map tx DMA buffer.\n", dev->name);
dev_kfree_skb(skb);
- netif_start_queue(dev);
return 1;
}
- entry = lp->cur_tx & SONIC_TDS_MASK;
+
+ sonic_tda_put(dev, entry, SONIC_TD_STATUS, 0); /* clear status */
+ sonic_tda_put(dev, entry, SONIC_TD_FRAG_COUNT, 1); /* single fragment */
+ sonic_tda_put(dev, entry, SONIC_TD_PKTSIZE, length); /* length of packet */
+ sonic_tda_put(dev, entry, SONIC_TD_FRAG_PTR_L, laddr & 0xffff);
+ sonic_tda_put(dev, entry, SONIC_TD_FRAG_PTR_H, laddr >> 16);
+ sonic_tda_put(dev, entry, SONIC_TD_FRAG_SIZE, length);
+ sonic_tda_put(dev, entry, SONIC_TD_LINK,
+ sonic_tda_get(dev, entry, SONIC_TD_LINK) | SONIC_EOL);
+
+ /*
+ * Must set tx_skb[entry] only after clearing status, and
+ * before clearing EOL and before stopping queue
+ */
+ wmb();
+ lp->tx_len[entry] = length;
lp->tx_laddr[entry] = laddr;
lp->tx_skb[entry] = skb;
- length = (skb->len < ETH_ZLEN) ? ETH_ZLEN : skb->len;
- flush_cache_all();
+ wmb();
+ sonic_tda_put(dev, lp->eol_tx, SONIC_TD_LINK,
+ sonic_tda_get(dev, lp->eol_tx, SONIC_TD_LINK) & ~SONIC_EOL);
+ lp->eol_tx = entry;
- /*
- * Setup the transmit descriptor and issue the transmit command.
- */
- lp->tda[entry].tx_status = 0; /* clear status */
- lp->tda[entry].tx_frag_count = 1; /* single fragment */
- lp->tda[entry].tx_pktsize = length; /* length of packet */
- lp->tda[entry].tx_frag_ptr_l = laddr & 0xffff;
- lp->tda[entry].tx_frag_ptr_h = laddr >> 16;
- lp->tda[entry].tx_frag_size = length;
- lp->cur_tx++;
- lp->stats.tx_bytes += length;
+ lp->next_tx = (entry + 1) & SONIC_TDS_MASK;
+ if (lp->tx_skb[lp->next_tx] != NULL) {
+ /* The ring is full, the ISR has yet to process the next TD. */
+ if (sonic_debug > 3)
+ printk("%s: stopping queue\n", dev->name);
+ netif_stop_queue(dev);
+ /* after this packet, wait for ISR to free up some TDAs */
+ } else netif_start_queue(dev);
if (sonic_debug > 2)
- printk("sonic_send_packet: issueing Tx command\n");
+ printk("sonic_send_packet: issuing Tx command\n");
SONIC_WRITE(SONIC_CMD, SONIC_CR_TXP);
dev->trans_start = jiffies;
- if (lp->cur_tx < lp->dirty_tx + SONIC_NUM_TDS)
- netif_start_queue(dev);
- else
- lp->tx_full = 1;
-
return 0;
}
@@ -164,175 +297,199 @@
static irqreturn_t sonic_interrupt(int irq, void *dev_id, struct pt_regs *regs)
{
struct net_device *dev = (struct net_device *) dev_id;
- unsigned int base_addr = dev->base_addr;
- struct sonic_local *lp;
+ struct sonic_local *lp = netdev_priv(dev);
int status;
if (dev == NULL) {
- printk("sonic_interrupt: irq %d for unknown device.\n", irq);
+ printk(KERN_ERR "sonic_interrupt: irq %d for unknown device.\n", irq);
return IRQ_NONE;
}
- lp = (struct sonic_local *) dev->priv;
+ if (!(status = SONIC_READ(SONIC_ISR) & SONIC_IMR_DEFAULT))
+ return IRQ_NONE;
- status = SONIC_READ(SONIC_ISR);
- SONIC_WRITE(SONIC_ISR, 0x7fff); /* clear all bits */
+ do {
+ if (status & SONIC_INT_PKTRX) {
+ if (sonic_debug > 2)
+ printk("%s: packet rx\n", dev->name);
+ sonic_rx(dev); /* got packet(s) */
+ SONIC_WRITE(SONIC_ISR, SONIC_INT_PKTRX); /* clear the interrupt */
+ }
- if (sonic_debug > 2)
- printk("sonic_interrupt: ISR=%x\n", status);
+ if (status & SONIC_INT_TXDN) {
+ int entry = lp->cur_tx;
+ int td_status;
+ int freed_some = 0;
- if (status & SONIC_INT_PKTRX) {
- sonic_rx(dev); /* got packet(s) */
- }
+ /* At this point, cur_tx is the index of a TD that is one of:
+ * unallocated/freed (status set & tx_skb[entry] clear)
+ * allocated and sent (status set & tx_skb[entry] set )
+ * allocated and not yet sent (status clear & tx_skb[entry] set )
+ * still being allocated by sonic_send_packet (status clear & tx_skb[entry] clear)
+ */
- if (status & SONIC_INT_TXDN) {
- int dirty_tx = lp->dirty_tx;
+ if (sonic_debug > 2)
+ printk("%s: tx done\n", dev->name);
- while (dirty_tx < lp->cur_tx) {
- int entry = dirty_tx & SONIC_TDS_MASK;
- int status = lp->tda[entry].tx_status;
+ while (lp->tx_skb[entry] != NULL) {
+ if ((td_status = sonic_tda_get(dev, entry, SONIC_TD_STATUS)) == 0)
+ break;
- if (sonic_debug > 3)
- printk
- ("sonic_interrupt: status %d, cur_tx %d, dirty_tx %d\n",
- status, lp->cur_tx, lp->dirty_tx);
+ if (td_status & 0x0001) {
+ lp->stats.tx_packets++;
+ lp->stats.tx_bytes += sonic_tda_get(dev, entry, SONIC_TD_PKTSIZE);
+ } else {
+ lp->stats.tx_errors++;
+ if (td_status & 0x0642)
+ lp->stats.tx_aborted_errors++;
+ if (td_status & 0x0180)
+ lp->stats.tx_carrier_errors++;
+ if (td_status & 0x0020)
+ lp->stats.tx_window_errors++;
+ if (td_status & 0x0004)
+ lp->stats.tx_fifo_errors++;
+ }
- if (status == 0) {
- /* It still hasn't been Txed, kick the sonic again */
- SONIC_WRITE(SONIC_CMD, SONIC_CR_TXP);
- break;
- }
-
- /* put back EOL and free descriptor */
- lp->tda[entry].tx_frag_count = 0;
- lp->tda[entry].tx_status = 0;
-
- if (status & 0x0001)
- lp->stats.tx_packets++;
- else {
- lp->stats.tx_errors++;
- if (status & 0x0642)
- lp->stats.tx_aborted_errors++;
- if (status & 0x0180)
- lp->stats.tx_carrier_errors++;
- if (status & 0x0020)
- lp->stats.tx_window_errors++;
- if (status & 0x0004)
- lp->stats.tx_fifo_errors++;
- }
-
- /* We must free the original skb */
- if (lp->tx_skb[entry]) {
+ /* We must free the original skb */
dev_kfree_skb_irq(lp->tx_skb[entry]);
- lp->tx_skb[entry] = 0;
+ lp->tx_skb[entry] = NULL;
+ /* and unmap DMA buffer */
+ dma_unmap_single(lp->device, lp->tx_laddr[entry], lp->tx_len[entry], DMA_TO_DEVICE);
+ lp->tx_laddr[entry] = (dma_addr_t)0;
+ freed_some = 1;
+
+ if (sonic_tda_get(dev, entry, SONIC_TD_LINK) & SONIC_EOL) {
+ entry = (entry + 1) & SONIC_TDS_MASK;
+ break;
+ }
+ entry = (entry + 1) & SONIC_TDS_MASK;
}
- /* and the VDMA address */
- vdma_free(lp->tx_laddr[entry]);
- dirty_tx++;
+
+ if (freed_some || lp->tx_skb[entry] == NULL)
+ netif_wake_queue(dev); /* The ring is no longer full */
+ lp->cur_tx = entry;
+ SONIC_WRITE(SONIC_ISR, SONIC_INT_TXDN); /* clear the interrupt */
}
- if (lp->tx_full
- && dirty_tx + SONIC_NUM_TDS > lp->cur_tx + 2) {
- /* The ring is no longer full, clear tbusy. */
- lp->tx_full = 0;
- netif_wake_queue(dev);
+ /*
+ * check error conditions
+ */
+ if (status & SONIC_INT_RFO) {
+ if (sonic_debug > 1)
+ printk("%s: rx fifo overrun\n", dev->name);
+ lp->stats.rx_fifo_errors++;
+ SONIC_WRITE(SONIC_ISR, SONIC_INT_RFO); /* clear the interrupt */
+ }
+ if (status & SONIC_INT_RDE) {
+ if (sonic_debug > 1)
+ printk("%s: rx descriptors exhausted\n", dev->name);
+ lp->stats.rx_dropped++;
+ SONIC_WRITE(SONIC_ISR, SONIC_INT_RDE); /* clear the interrupt */
+ }
+ if (status & SONIC_INT_RBAE) {
+ if (sonic_debug > 1)
+ printk("%s: rx buffer area exceeded\n", dev->name);
+ lp->stats.rx_dropped++;
+ SONIC_WRITE(SONIC_ISR, SONIC_INT_RBAE); /* clear the interrupt */
}
- lp->dirty_tx = dirty_tx;
- }
+ /* counter overruns; all counters are 16bit wide */
+ if (status & SONIC_INT_FAE) {
+ lp->stats.rx_frame_errors += 65536;
+ SONIC_WRITE(SONIC_ISR, SONIC_INT_FAE); /* clear the interrupt */
+ }
+ if (status & SONIC_INT_CRC) {
+ lp->stats.rx_crc_errors += 65536;
+ SONIC_WRITE(SONIC_ISR, SONIC_INT_CRC); /* clear the interrupt */
+ }
+ if (status & SONIC_INT_MP) {
+ lp->stats.rx_missed_errors += 65536;
+ SONIC_WRITE(SONIC_ISR, SONIC_INT_MP); /* clear the interrupt */
+ }
- /*
- * check error conditions
- */
- if (status & SONIC_INT_RFO) {
- printk("%s: receive fifo underrun\n", dev->name);
- lp->stats.rx_fifo_errors++;
- }
- if (status & SONIC_INT_RDE) {
- printk("%s: receive descriptors exhausted\n", dev->name);
- lp->stats.rx_dropped++;
- }
- if (status & SONIC_INT_RBE) {
- printk("%s: receive buffer exhausted\n", dev->name);
- lp->stats.rx_dropped++;
- }
- if (status & SONIC_INT_RBAE) {
- printk("%s: receive buffer area exhausted\n", dev->name);
- lp->stats.rx_dropped++;
- }
+ /* transmit error */
+ if (status & SONIC_INT_TXER) {
+ if ((SONIC_READ(SONIC_TCR) & SONIC_TCR_FU) && (sonic_debug > 2))
+ printk(KERN_ERR "%s: tx fifo underrun\n", dev->name);
+ SONIC_WRITE(SONIC_ISR, SONIC_INT_TXER); /* clear the interrupt */
+ }
- /* counter overruns; all counters are 16bit wide */
- if (status & SONIC_INT_FAE)
- lp->stats.rx_frame_errors += 65536;
- if (status & SONIC_INT_CRC)
- lp->stats.rx_crc_errors += 65536;
- if (status & SONIC_INT_MP)
- lp->stats.rx_missed_errors += 65536;
+ /* bus retry */
+ if (status & SONIC_INT_BR) {
+ printk(KERN_ERR "%s: Bus retry occurred! Device interrupt disabled.\n",
+ dev->name);
+ /* ... to help debug DMA problems causing endless interrupts. */
+ /* Bounce the eth interface to turn on the interrupt again. */
+ SONIC_WRITE(SONIC_IMR, 0);
+ SONIC_WRITE(SONIC_ISR, SONIC_INT_BR); /* clear the interrupt */
+ }
- /* transmit error */
- if (status & SONIC_INT_TXER)
- lp->stats.tx_errors++;
-
- /*
- * clear interrupt bits and return
- */
- SONIC_WRITE(SONIC_ISR, status);
+ /* load CAM done */
+ if (status & SONIC_INT_LCD)
+ SONIC_WRITE(SONIC_ISR, SONIC_INT_LCD); /* clear the interrupt */
+ } while((status = SONIC_READ(SONIC_ISR) & SONIC_IMR_DEFAULT));
return IRQ_HANDLED;
}
/*
- * We have a good packet(s), get it/them out of the buffers.
+ * We have a good packet(s), pass it/them up the network stack.
*/
static void sonic_rx(struct net_device *dev)
{
- unsigned int base_addr = dev->base_addr;
- struct sonic_local *lp = (struct sonic_local *) dev->priv;
- sonic_rd_t *rd = &lp->rda[lp->cur_rx & SONIC_RDS_MASK];
+ struct sonic_local *lp = netdev_priv(dev);
int status;
+ int entry = lp->cur_rx;
- while (rd->in_use == 0) {
- struct sk_buff *skb;
+ while (sonic_rda_get(dev, entry, SONIC_RD_IN_USE) == 0) {
+ struct sk_buff *used_skb;
+ struct sk_buff *new_skb;
+ dma_addr_t new_laddr;
+ u16 bufadr_l;
+ u16 bufadr_h;
int pkt_len;
- unsigned char *pkt_ptr;
- status = rd->rx_status;
- if (sonic_debug > 3)
- printk("status %x, cur_rx %d, cur_rra %x\n",
- status, lp->cur_rx, lp->cur_rra);
+ status = sonic_rda_get(dev, entry, SONIC_RD_STATUS);
if (status & SONIC_RCR_PRX) {
- pkt_len = rd->rx_pktlen;
- pkt_ptr =
- (char *)
- sonic_chiptomem((rd->rx_pktptr_h << 16) +
- rd->rx_pktptr_l);
-
- if (sonic_debug > 3)
- printk
- ("pktptr %p (rba %p) h:%x l:%x, bsize h:%x l:%x\n",
- pkt_ptr, lp->rba, rd->rx_pktptr_h,
- rd->rx_pktptr_l,
- SONIC_READ(SONIC_RBWC1),
- SONIC_READ(SONIC_RBWC0));
-
/* Malloc up new buffer. */
- skb = dev_alloc_skb(pkt_len + 2);
- if (skb == NULL) {
- printk
- ("%s: Memory squeeze, dropping packet.\n",
- dev->name);
+ new_skb = dev_alloc_skb(SONIC_RBSIZE + 2);
+ if (new_skb == NULL) {
+ printk(KERN_ERR "%s: Memory squeeze, dropping packet.\n", dev->name);
lp->stats.rx_dropped++;
break;
}
- skb->dev = dev;
- skb_reserve(skb, 2); /* 16 byte align */
- skb_put(skb, pkt_len); /* Make room */
- eth_copy_and_sum(skb, pkt_ptr, pkt_len, 0);
- skb->protocol = eth_type_trans(skb, dev);
- netif_rx(skb); /* pass the packet to upper layers */
+ new_skb->dev = dev;
+ /* provide 16 byte IP header alignment unless DMA requires otherwise */
+ if(SONIC_BUS_SCALE(lp->dma_bitmode) == 2)
+ skb_reserve(new_skb, 2);
+
+ new_laddr = dma_map_single(lp->device, skb_put(new_skb, SONIC_RBSIZE),
+ SONIC_RBSIZE, DMA_FROM_DEVICE);
+ if (!new_laddr) {
+ dev_kfree_skb(new_skb);
+ printk(KERN_ERR "%s: Failed to map rx buffer, dropping packet.\n", dev->name);
+ lp->stats.rx_dropped++;
+ break;
+ }
+
+ /* now we have a new skb to replace it, pass the used one up the stack */
+ dma_unmap_single(lp->device, lp->rx_laddr[entry], SONIC_RBSIZE, DMA_FROM_DEVICE);
+ used_skb = lp->rx_skb[entry];
+ pkt_len = sonic_rda_get(dev, entry, SONIC_RD_PKTLEN);
+ skb_trim(used_skb, pkt_len);
+ used_skb->protocol = eth_type_trans(used_skb, dev);
+ netif_rx(used_skb);
dev->last_rx = jiffies;
lp->stats.rx_packets++;
lp->stats.rx_bytes += pkt_len;
+ /* and insert the new skb */
+ lp->rx_laddr[entry] = new_laddr;
+ lp->rx_skb[entry] = new_skb;
+
+ bufadr_l = (unsigned long)new_laddr & 0xffff;
+ bufadr_h = (unsigned long)new_laddr >> 16;
+ sonic_rra_put(dev, entry, SONIC_RR_BUFADR_L, bufadr_l);
+ sonic_rra_put(dev, entry, SONIC_RR_BUFADR_H, bufadr_h);
} else {
/* This should only happen, if we enable accepting broken packets. */
lp->stats.rx_errors++;
@@ -341,29 +498,35 @@
if (status & SONIC_RCR_CRCR)
lp->stats.rx_crc_errors++;
}
-
- rd->in_use = 1;
- rd = &lp->rda[(++lp->cur_rx) & SONIC_RDS_MASK];
- /* now give back the buffer to the receive buffer area */
if (status & SONIC_RCR_LPKT) {
/*
- * this was the last packet out of the current receice buffer
+ * this was the last packet out of the current receive buffer
* give the buffer back to the SONIC
*/
- lp->cur_rra += sizeof(sonic_rr_t);
- if (lp->cur_rra >
- (lp->rra_laddr +
- (SONIC_NUM_RRS -
- 1) * sizeof(sonic_rr_t))) lp->cur_rra =
- lp->rra_laddr;
- SONIC_WRITE(SONIC_RWP, lp->cur_rra & 0xffff);
+ lp->cur_rwp += SIZEOF_SONIC_RR * SONIC_BUS_SCALE(lp->dma_bitmode);
+ if (lp->cur_rwp >= lp->rra_end) lp->cur_rwp = lp->rra_laddr & 0xffff;
+ SONIC_WRITE(SONIC_RWP, lp->cur_rwp);
+ if (SONIC_READ(SONIC_ISR) & SONIC_INT_RBE) {
+ if (sonic_debug > 2)
+ printk("%s: rx buffer exhausted\n", dev->name);
+ SONIC_WRITE(SONIC_ISR, SONIC_INT_RBE); /* clear the flag */
+ }
} else
- printk
- ("%s: rx desc without RCR_LPKT. Shouldn't happen !?\n",
+ printk(KERN_ERR "%s: rx desc without RCR_LPKT. Shouldn't happen !?\n",
dev->name);
+ /*
+ * give back the descriptor
+ */
+ sonic_rda_put(dev, entry, SONIC_RD_LINK,
+ sonic_rda_get(dev, entry, SONIC_RD_LINK) | SONIC_EOL);
+ sonic_rda_put(dev, entry, SONIC_RD_IN_USE, 1);
+ sonic_rda_put(dev, lp->eol_rx, SONIC_RD_LINK,
+ sonic_rda_get(dev, lp->eol_rx, SONIC_RD_LINK) & ~SONIC_EOL);
+ lp->eol_rx = entry;
+ lp->cur_rx = entry = (entry + 1) & SONIC_RDS_MASK;
}
/*
- * If any worth-while packets have been received, dev_rint()
+ * If any worth-while packets have been received, netif_rx()
* has done a mark_bh(NET_BH) for us and will work on them
* when we get to the bottom-half routine.
*/
@@ -376,8 +539,7 @@
*/
static struct net_device_stats *sonic_get_stats(struct net_device *dev)
{
- struct sonic_local *lp = (struct sonic_local *) dev->priv;
- unsigned int base_addr = dev->base_addr;
+ struct sonic_local *lp = netdev_priv(dev);
/* read the tally counter from the SONIC and reset them */
lp->stats.rx_crc_errors += SONIC_READ(SONIC_CRCT);
@@ -396,8 +558,7 @@
*/
static void sonic_multicast_list(struct net_device *dev)
{
- struct sonic_local *lp = (struct sonic_local *) dev->priv;
- unsigned int base_addr = dev->base_addr;
+ struct sonic_local *lp = netdev_priv(dev);
unsigned int rcr;
struct dev_mc_list *dmi = dev->mc_list;
unsigned char *addr;
@@ -413,20 +574,15 @@
rcr |= SONIC_RCR_AMC;
} else {
if (sonic_debug > 2)
- printk
- ("sonic_multicast_list: mc_count %d\n",
- dev->mc_count);
- lp->cda.cam_enable = 1; /* always enable our own address */
+ printk("sonic_multicast_list: mc_count %d\n", dev->mc_count);
+ sonic_set_cam_enable(dev, 1); /* always enable our own address */
for (i = 1; i <= dev->mc_count; i++) {
addr = dmi->dmi_addr;
dmi = dmi->next;
- lp->cda.cam_desc[i].cam_cap0 =
- addr[1] << 8 | addr[0];
- lp->cda.cam_desc[i].cam_cap1 =
- addr[3] << 8 | addr[2];
- lp->cda.cam_desc[i].cam_cap2 =
- addr[5] << 8 | addr[4];
- lp->cda.cam_enable |= (1 << i);
+ sonic_cda_put(dev, i, SONIC_CD_CAP0, addr[1] << 8 | addr[0]);
+ sonic_cda_put(dev, i, SONIC_CD_CAP1, addr[3] << 8 | addr[2]);
+ sonic_cda_put(dev, i, SONIC_CD_CAP2, addr[5] << 8 | addr[4]);
+ sonic_set_cam_enable(dev, sonic_get_cam_enable(dev) | (1 << i));
}
SONIC_WRITE(SONIC_CDC, 16);
/* issue Load CAM command */
@@ -447,19 +603,16 @@
*/
static int sonic_init(struct net_device *dev)
{
- unsigned int base_addr = dev->base_addr;
unsigned int cmd;
- struct sonic_local *lp = (struct sonic_local *) dev->priv;
- unsigned int rra_start;
- unsigned int rra_end;
+ struct sonic_local *lp = netdev_priv(dev);
int i;
/*
* put the Sonic into software-reset mode and
* disable all interrupts
*/
- SONIC_WRITE(SONIC_ISR, 0x7fff);
SONIC_WRITE(SONIC_IMR, 0);
+ SONIC_WRITE(SONIC_ISR, 0x7fff);
SONIC_WRITE(SONIC_CMD, SONIC_CR_RST);
/*
@@ -475,34 +628,32 @@
if (sonic_debug > 2)
printk("sonic_init: initialize receive resource area\n");
- rra_start = lp->rra_laddr & 0xffff;
- rra_end =
- (rra_start + (SONIC_NUM_RRS * sizeof(sonic_rr_t))) & 0xffff;
-
for (i = 0; i < SONIC_NUM_RRS; i++) {
- lp->rra[i].rx_bufadr_l =
- (lp->rba_laddr + i * SONIC_RBSIZE) & 0xffff;
- lp->rra[i].rx_bufadr_h =
- (lp->rba_laddr + i * SONIC_RBSIZE) >> 16;
- lp->rra[i].rx_bufsize_l = SONIC_RBSIZE >> 1;
- lp->rra[i].rx_bufsize_h = 0;
+ u16 bufadr_l = (unsigned long)lp->rx_laddr[i] & 0xffff;
+ u16 bufadr_h = (unsigned long)lp->rx_laddr[i] >> 16;
+ sonic_rra_put(dev, i, SONIC_RR_BUFADR_L, bufadr_l);
+ sonic_rra_put(dev, i, SONIC_RR_BUFADR_H, bufadr_h);
+ sonic_rra_put(dev, i, SONIC_RR_BUFSIZE_L, SONIC_RBSIZE >> 1);
+ sonic_rra_put(dev, i, SONIC_RR_BUFSIZE_H, 0);
}
/* initialize all RRA registers */
- SONIC_WRITE(SONIC_RSA, rra_start);
- SONIC_WRITE(SONIC_REA, rra_end);
- SONIC_WRITE(SONIC_RRP, rra_start);
- SONIC_WRITE(SONIC_RWP, rra_end);
+ lp->rra_end = (lp->rra_laddr + SONIC_NUM_RRS * SIZEOF_SONIC_RR *
+ SONIC_BUS_SCALE(lp->dma_bitmode)) & 0xffff;
+ lp->cur_rwp = (lp->rra_laddr + (SONIC_NUM_RRS - 1) * SIZEOF_SONIC_RR *
+ SONIC_BUS_SCALE(lp->dma_bitmode)) & 0xffff;
+
+ SONIC_WRITE(SONIC_RSA, lp->rra_laddr & 0xffff);
+ SONIC_WRITE(SONIC_REA, lp->rra_end);
+ SONIC_WRITE(SONIC_RRP, lp->rra_laddr & 0xffff);
+ SONIC_WRITE(SONIC_RWP, lp->cur_rwp);
SONIC_WRITE(SONIC_URRA, lp->rra_laddr >> 16);
- SONIC_WRITE(SONIC_EOBC, (SONIC_RBSIZE - 2) >> 1);
-
- lp->cur_rra =
- lp->rra_laddr + (SONIC_NUM_RRS - 1) * sizeof(sonic_rr_t);
+ SONIC_WRITE(SONIC_EOBC, (SONIC_RBSIZE >> 1) - (lp->dma_bitmode ? 2 : 1));
/* load the resource pointers */
if (sonic_debug > 3)
- printk("sonic_init: issueing RRRA command\n");
-
+ printk("sonic_init: issuing RRRA command\n");
+
SONIC_WRITE(SONIC_CMD, SONIC_CR_RRRA);
i = 0;
while (i++ < 100) {
@@ -511,27 +662,30 @@
}
if (sonic_debug > 2)
- printk("sonic_init: status=%x\n", SONIC_READ(SONIC_CMD));
-
+ printk("sonic_init: status=%x i=%d\n", SONIC_READ(SONIC_CMD), i);
+
/*
* Initialize the receive descriptors so that they
* become a circular linked list, ie. let the last
* descriptor point to the first again.
*/
if (sonic_debug > 2)
- printk("sonic_init: initialize receive descriptors\n");
- for (i = 0; i < SONIC_NUM_RDS; i++) {
- lp->rda[i].rx_status = 0;
- lp->rda[i].rx_pktlen = 0;
- lp->rda[i].rx_pktptr_l = 0;
- lp->rda[i].rx_pktptr_h = 0;
- lp->rda[i].rx_seqno = 0;
- lp->rda[i].in_use = 1;
- lp->rda[i].link =
- lp->rda_laddr + (i + 1) * sizeof(sonic_rd_t);
+ printk("sonic_init: initialize receive descriptors\n");
+ for (i=0; i<SONIC_NUM_RDS; i++) {
+ sonic_rda_put(dev, i, SONIC_RD_STATUS, 0);
+ sonic_rda_put(dev, i, SONIC_RD_PKTLEN, 0);
+ sonic_rda_put(dev, i, SONIC_RD_PKTPTR_L, 0);
+ sonic_rda_put(dev, i, SONIC_RD_PKTPTR_H, 0);
+ sonic_rda_put(dev, i, SONIC_RD_SEQNO, 0);
+ sonic_rda_put(dev, i, SONIC_RD_IN_USE, 1);
+ sonic_rda_put(dev, i, SONIC_RD_LINK,
+ lp->rda_laddr +
+ ((i+1) * SIZEOF_SONIC_RD * SONIC_BUS_SCALE(lp->dma_bitmode)));
}
/* fix last descriptor */
- lp->rda[SONIC_NUM_RDS - 1].link = lp->rda_laddr;
+ sonic_rda_put(dev, SONIC_NUM_RDS - 1, SONIC_RD_LINK,
+ (lp->rda_laddr & 0xffff) | SONIC_EOL);
+ lp->eol_rx = SONIC_NUM_RDS - 1;
lp->cur_rx = 0;
SONIC_WRITE(SONIC_URDA, lp->rda_laddr >> 16);
SONIC_WRITE(SONIC_CRDA, lp->rda_laddr & 0xffff);
@@ -542,34 +696,34 @@
if (sonic_debug > 2)
printk("sonic_init: initialize transmit descriptors\n");
for (i = 0; i < SONIC_NUM_TDS; i++) {
- lp->tda[i].tx_status = 0;
- lp->tda[i].tx_config = 0;
- lp->tda[i].tx_pktsize = 0;
- lp->tda[i].tx_frag_count = 0;
- lp->tda[i].link =
- (lp->tda_laddr +
- (i + 1) * sizeof(sonic_td_t)) | SONIC_END_OF_LINKS;
+ sonic_tda_put(dev, i, SONIC_TD_STATUS, 0);
+ sonic_tda_put(dev, i, SONIC_TD_CONFIG, 0);
+ sonic_tda_put(dev, i, SONIC_TD_PKTSIZE, 0);
+ sonic_tda_put(dev, i, SONIC_TD_FRAG_COUNT, 0);
+ sonic_tda_put(dev, i, SONIC_TD_LINK,
+ (lp->tda_laddr & 0xffff) +
+ (i + 1) * SIZEOF_SONIC_TD * SONIC_BUS_SCALE(lp->dma_bitmode));
+ lp->tx_skb[i] = NULL;
}
- lp->tda[SONIC_NUM_TDS - 1].link =
- (lp->tda_laddr & 0xffff) | SONIC_END_OF_LINKS;
+ /* fix last descriptor */
+ sonic_tda_put(dev, SONIC_NUM_TDS - 1, SONIC_TD_LINK,
+ (lp->tda_laddr & 0xffff));
SONIC_WRITE(SONIC_UTDA, lp->tda_laddr >> 16);
SONIC_WRITE(SONIC_CTDA, lp->tda_laddr & 0xffff);
- lp->cur_tx = lp->dirty_tx = 0;
-
+ lp->cur_tx = lp->next_tx = 0;
+ lp->eol_tx = SONIC_NUM_TDS - 1;
+
/*
* put our own address to CAM desc[0]
*/
- lp->cda.cam_desc[0].cam_cap0 =
- dev->dev_addr[1] << 8 | dev->dev_addr[0];
- lp->cda.cam_desc[0].cam_cap1 =
- dev->dev_addr[3] << 8 | dev->dev_addr[2];
- lp->cda.cam_desc[0].cam_cap2 =
- dev->dev_addr[5] << 8 | dev->dev_addr[4];
- lp->cda.cam_enable = 1;
+ sonic_cda_put(dev, 0, SONIC_CD_CAP0, dev->dev_addr[1] << 8 | dev->dev_addr[0]);
+ sonic_cda_put(dev, 0, SONIC_CD_CAP1, dev->dev_addr[3] << 8 | dev->dev_addr[2]);
+ sonic_cda_put(dev, 0, SONIC_CD_CAP2, dev->dev_addr[5] << 8 | dev->dev_addr[4]);
+ sonic_set_cam_enable(dev, 1);
for (i = 0; i < 16; i++)
- lp->cda.cam_desc[i].cam_entry_pointer = i;
+ sonic_cda_put(dev, i, SONIC_CD_ENTRY_POINTER, i);
/*
* initialize CAM registers
@@ -588,8 +742,8 @@
break;
}
if (sonic_debug > 2) {
- printk("sonic_init: CMD=%x, ISR=%x\n",
- SONIC_READ(SONIC_CMD), SONIC_READ(SONIC_ISR));
+ printk("sonic_init: CMD=%x, ISR=%x\n, i=%d",
+ SONIC_READ(SONIC_CMD), SONIC_READ(SONIC_ISR), i);
}
/*
@@ -604,7 +758,7 @@
cmd = SONIC_READ(SONIC_CMD);
if ((cmd & SONIC_CR_RXEN) == 0 || (cmd & SONIC_CR_STP) == 0)
- printk("sonic_init: failed, status=%x\n", cmd);
+ printk(KERN_ERR "sonic_init: failed, status=%x\n", cmd);
if (sonic_debug > 2)
printk("sonic_init: new status=%x\n",
diff --git a/drivers/net/sonic.h b/drivers/net/sonic.h
index c4a6d58..cede969a 100644
--- a/drivers/net/sonic.h
+++ b/drivers/net/sonic.h
@@ -1,5 +1,5 @@
/*
- * Helpfile for sonic.c
+ * Header file for sonic.c
*
* (C) Waldorf Electronics, Germany
* Written by Andreas Busse
@@ -9,10 +9,16 @@
* and pad structure members must be exchanged. Also, the structures
* need to be changed accordingly to the bus size.
*
- * 981229 MSch: did just that for the 68k Mac port (32 bit, big endian),
- * see CONFIG_MACSONIC branch below.
+ * 981229 MSch: did just that for the 68k Mac port (32 bit, big endian)
*
+ * 990611 David Huggins-Daines <dhd@debian.org>: This machine abstraction
+ * does not cope with 16-bit bus sizes very well. Therefore I have
+ * rewritten it with ugly macros and evil inlines.
+ *
+ * 050625 Finn Thain: introduced more 32-bit cards and dhd's support
+ * for 16-bit cards (from the mac68k project).
*/
+
#ifndef SONIC_H
#define SONIC_H
@@ -83,6 +89,7 @@
/*
* Error counters
*/
+
#define SONIC_CRCT 0x2c
#define SONIC_FAET 0x2d
#define SONIC_MPT 0x2e
@@ -182,14 +189,14 @@
#define SONIC_INT_BR 0x4000
#define SONIC_INT_HBL 0x2000
-#define SONIC_INT_LCD 0x1000
-#define SONIC_INT_PINT 0x0800
-#define SONIC_INT_PKTRX 0x0400
-#define SONIC_INT_TXDN 0x0200
-#define SONIC_INT_TXER 0x0100
-#define SONIC_INT_TC 0x0080
-#define SONIC_INT_RDE 0x0040
-#define SONIC_INT_RBE 0x0020
+#define SONIC_INT_LCD 0x1000
+#define SONIC_INT_PINT 0x0800
+#define SONIC_INT_PKTRX 0x0400
+#define SONIC_INT_TXDN 0x0200
+#define SONIC_INT_TXER 0x0100
+#define SONIC_INT_TC 0x0080
+#define SONIC_INT_RDE 0x0040
+#define SONIC_INT_RBE 0x0020
#define SONIC_INT_RBAE 0x0010
#define SONIC_INT_CRC 0x0008
#define SONIC_INT_FAE 0x0004
@@ -201,224 +208,61 @@
* The interrupts we allow.
*/
-#define SONIC_IMR_DEFAULT (SONIC_INT_BR | \
- SONIC_INT_LCD | \
- SONIC_INT_PINT | \
+#define SONIC_IMR_DEFAULT ( SONIC_INT_BR | \
+ SONIC_INT_LCD | \
+ SONIC_INT_RFO | \
SONIC_INT_PKTRX | \
SONIC_INT_TXDN | \
SONIC_INT_TXER | \
SONIC_INT_RDE | \
- SONIC_INT_RBE | \
SONIC_INT_RBAE | \
SONIC_INT_CRC | \
SONIC_INT_FAE | \
SONIC_INT_MP)
-#define SONIC_END_OF_LINKS 0x0001
-
-
-#ifdef CONFIG_MACSONIC
-/*
- * Big endian like structures on 680x0 Macs
- */
-
-typedef struct {
- u32 rx_bufadr_l; /* receive buffer ptr */
- u32 rx_bufadr_h;
-
- u32 rx_bufsize_l; /* no. of words in the receive buffer */
- u32 rx_bufsize_h;
-} sonic_rr_t;
-
-/*
- * Sonic receive descriptor. Receive descriptors are
- * kept in a linked list of these structures.
- */
-
-typedef struct {
- SREGS_PAD(pad0);
- u16 rx_status; /* status after reception of a packet */
- SREGS_PAD(pad1);
- u16 rx_pktlen; /* length of the packet incl. CRC */
-
- /*
- * Pointers to the location in the receive buffer area (RBA)
- * where the packet resides. A packet is always received into
- * a contiguous piece of memory.
- */
- SREGS_PAD(pad2);
- u16 rx_pktptr_l;
- SREGS_PAD(pad3);
- u16 rx_pktptr_h;
-
- SREGS_PAD(pad4);
- u16 rx_seqno; /* sequence no. */
-
- SREGS_PAD(pad5);
- u16 link; /* link to next RDD (end if EOL bit set) */
-
- /*
- * Owner of this descriptor, 0= driver, 1=sonic
- */
-
- SREGS_PAD(pad6);
- u16 in_use;
-
- caddr_t rda_next; /* pointer to next RD */
-} sonic_rd_t;
-
-
-/*
- * Describes a Transmit Descriptor
- */
-typedef struct {
- SREGS_PAD(pad0);
- u16 tx_status; /* status after transmission of a packet */
- SREGS_PAD(pad1);
- u16 tx_config; /* transmit configuration for this packet */
- SREGS_PAD(pad2);
- u16 tx_pktsize; /* size of the packet to be transmitted */
- SREGS_PAD(pad3);
- u16 tx_frag_count; /* no. of fragments */
-
- SREGS_PAD(pad4);
- u16 tx_frag_ptr_l;
- SREGS_PAD(pad5);
- u16 tx_frag_ptr_h;
- SREGS_PAD(pad6);
- u16 tx_frag_size;
-
- SREGS_PAD(pad7);
- u16 link; /* ptr to next descriptor */
-} sonic_td_t;
-
-
-/*
- * Describes an entry in the CAM Descriptor Area.
- */
-
-typedef struct {
- SREGS_PAD(pad0);
- u16 cam_entry_pointer;
- SREGS_PAD(pad1);
- u16 cam_cap0;
- SREGS_PAD(pad2);
- u16 cam_cap1;
- SREGS_PAD(pad3);
- u16 cam_cap2;
-} sonic_cd_t;
-
+#define SONIC_EOL 0x0001
#define CAM_DESCRIPTORS 16
+/* Offsets in the various DMA buffers accessed by the SONIC */
-typedef struct {
- sonic_cd_t cam_desc[CAM_DESCRIPTORS];
- SREGS_PAD(pad);
- u16 cam_enable;
-} sonic_cda_t;
+#define SONIC_BITMODE16 0
+#define SONIC_BITMODE32 1
+#define SONIC_BUS_SCALE(bitmode) ((bitmode) ? 4 : 2)
+/* Note! These are all measured in bus-size units, so use SONIC_BUS_SCALE */
+#define SIZEOF_SONIC_RR 4
+#define SONIC_RR_BUFADR_L 0
+#define SONIC_RR_BUFADR_H 1
+#define SONIC_RR_BUFSIZE_L 2
+#define SONIC_RR_BUFSIZE_H 3
-#else /* original declarations, little endian 32 bit */
+#define SIZEOF_SONIC_RD 7
+#define SONIC_RD_STATUS 0
+#define SONIC_RD_PKTLEN 1
+#define SONIC_RD_PKTPTR_L 2
+#define SONIC_RD_PKTPTR_H 3
+#define SONIC_RD_SEQNO 4
+#define SONIC_RD_LINK 5
+#define SONIC_RD_IN_USE 6
-/*
- * structure definitions
- */
+#define SIZEOF_SONIC_TD 8
+#define SONIC_TD_STATUS 0
+#define SONIC_TD_CONFIG 1
+#define SONIC_TD_PKTSIZE 2
+#define SONIC_TD_FRAG_COUNT 3
+#define SONIC_TD_FRAG_PTR_L 4
+#define SONIC_TD_FRAG_PTR_H 5
+#define SONIC_TD_FRAG_SIZE 6
+#define SONIC_TD_LINK 7
-typedef struct {
- u32 rx_bufadr_l; /* receive buffer ptr */
- u32 rx_bufadr_h;
+#define SIZEOF_SONIC_CD 4
+#define SONIC_CD_ENTRY_POINTER 0
+#define SONIC_CD_CAP0 1
+#define SONIC_CD_CAP1 2
+#define SONIC_CD_CAP2 3
- u32 rx_bufsize_l; /* no. of words in the receive buffer */
- u32 rx_bufsize_h;
-} sonic_rr_t;
-
-/*
- * Sonic receive descriptor. Receive descriptors are
- * kept in a linked list of these structures.
- */
-
-typedef struct {
- u16 rx_status; /* status after reception of a packet */
- SREGS_PAD(pad0);
- u16 rx_pktlen; /* length of the packet incl. CRC */
- SREGS_PAD(pad1);
-
- /*
- * Pointers to the location in the receive buffer area (RBA)
- * where the packet resides. A packet is always received into
- * a contiguous piece of memory.
- */
- u16 rx_pktptr_l;
- SREGS_PAD(pad2);
- u16 rx_pktptr_h;
- SREGS_PAD(pad3);
-
- u16 rx_seqno; /* sequence no. */
- SREGS_PAD(pad4);
-
- u16 link; /* link to next RDD (end if EOL bit set) */
- SREGS_PAD(pad5);
-
- /*
- * Owner of this descriptor, 0= driver, 1=sonic
- */
-
- u16 in_use;
- SREGS_PAD(pad6);
-
- caddr_t rda_next; /* pointer to next RD */
-} sonic_rd_t;
-
-
-/*
- * Describes a Transmit Descriptor
- */
-typedef struct {
- u16 tx_status; /* status after transmission of a packet */
- SREGS_PAD(pad0);
- u16 tx_config; /* transmit configuration for this packet */
- SREGS_PAD(pad1);
- u16 tx_pktsize; /* size of the packet to be transmitted */
- SREGS_PAD(pad2);
- u16 tx_frag_count; /* no. of fragments */
- SREGS_PAD(pad3);
-
- u16 tx_frag_ptr_l;
- SREGS_PAD(pad4);
- u16 tx_frag_ptr_h;
- SREGS_PAD(pad5);
- u16 tx_frag_size;
- SREGS_PAD(pad6);
-
- u16 link; /* ptr to next descriptor */
- SREGS_PAD(pad7);
-} sonic_td_t;
-
-
-/*
- * Describes an entry in the CAM Descriptor Area.
- */
-
-typedef struct {
- u16 cam_entry_pointer;
- SREGS_PAD(pad0);
- u16 cam_cap0;
- SREGS_PAD(pad1);
- u16 cam_cap1;
- SREGS_PAD(pad2);
- u16 cam_cap2;
- SREGS_PAD(pad3);
-} sonic_cd_t;
-
-#define CAM_DESCRIPTORS 16
-
-
-typedef struct {
- sonic_cd_t cam_desc[CAM_DESCRIPTORS];
- u16 cam_enable;
- SREGS_PAD(pad);
-} sonic_cda_t;
-#endif /* endianness */
+#define SIZEOF_SONIC_CDA ((CAM_DESCRIPTORS * SIZEOF_SONIC_CD) + 1)
+#define SONIC_CDA_CAM_ENABLE (CAM_DESCRIPTORS * SIZEOF_SONIC_CD)
/*
* Some tunables for the buffer areas. Power of 2 is required
@@ -426,44 +270,60 @@
*
* MSch: use more buffer space for the slow m68k Macs!
*/
-#ifdef CONFIG_MACSONIC
-#define SONIC_NUM_RRS 32 /* number of receive resources */
-#define SONIC_NUM_RDS SONIC_NUM_RRS /* number of receive descriptors */
-#define SONIC_NUM_TDS 32 /* number of transmit descriptors */
-#else
-#define SONIC_NUM_RRS 16 /* number of receive resources */
-#define SONIC_NUM_RDS SONIC_NUM_RRS /* number of receive descriptors */
-#define SONIC_NUM_TDS 16 /* number of transmit descriptors */
-#endif
-#define SONIC_RBSIZE 1520 /* size of one resource buffer */
+#define SONIC_NUM_RRS 16 /* number of receive resources */
+#define SONIC_NUM_RDS SONIC_NUM_RRS /* number of receive descriptors */
+#define SONIC_NUM_TDS 16 /* number of transmit descriptors */
-#define SONIC_RDS_MASK (SONIC_NUM_RDS-1)
-#define SONIC_TDS_MASK (SONIC_NUM_TDS-1)
+#define SONIC_RDS_MASK (SONIC_NUM_RDS-1)
+#define SONIC_TDS_MASK (SONIC_NUM_TDS-1)
+#define SONIC_RBSIZE 1520 /* size of one resource buffer */
+
+/* Again, measured in bus size units! */
+#define SIZEOF_SONIC_DESC (SIZEOF_SONIC_CDA \
+ + (SIZEOF_SONIC_TD * SONIC_NUM_TDS) \
+ + (SIZEOF_SONIC_RD * SONIC_NUM_RDS) \
+ + (SIZEOF_SONIC_RR * SONIC_NUM_RRS))
/* Information that need to be kept for each board. */
struct sonic_local {
- sonic_cda_t cda; /* virtual CPU address of CDA */
- sonic_td_t tda[SONIC_NUM_TDS]; /* transmit descriptor area */
- sonic_rr_t rra[SONIC_NUM_RRS]; /* receive resource area */
- sonic_rd_t rda[SONIC_NUM_RDS]; /* receive descriptor area */
- struct sk_buff *tx_skb[SONIC_NUM_TDS]; /* skbuffs for packets to transmit */
- unsigned int tx_laddr[SONIC_NUM_TDS]; /* logical DMA address fro skbuffs */
- unsigned char *rba; /* start of receive buffer areas */
- unsigned int cda_laddr; /* logical DMA address of CDA */
- unsigned int tda_laddr; /* logical DMA address of TDA */
- unsigned int rra_laddr; /* logical DMA address of RRA */
- unsigned int rda_laddr; /* logical DMA address of RDA */
- unsigned int rba_laddr; /* logical DMA address of RBA */
- unsigned int cur_rra; /* current indexes to resource areas */
+ /* Bus size. 0 == 16 bits, 1 == 32 bits. */
+ int dma_bitmode;
+ /* Register offset within the longword (independent of endianness,
+ and varies from one type of Macintosh SONIC to another
+ (Aarrgh)) */
+ int reg_offset;
+ void *descriptors;
+ /* Crud. These areas have to be within the same 64K. Therefore
+ we allocate a desriptors page, and point these to places within it. */
+ void *cda; /* CAM descriptor area */
+ void *tda; /* Transmit descriptor area */
+ void *rra; /* Receive resource area */
+ void *rda; /* Receive descriptor area */
+ struct sk_buff* volatile rx_skb[SONIC_NUM_RRS]; /* packets to be received */
+ struct sk_buff* volatile tx_skb[SONIC_NUM_TDS]; /* packets to be transmitted */
+ unsigned int tx_len[SONIC_NUM_TDS]; /* lengths of tx DMA mappings */
+ /* Logical DMA addresses on MIPS, bus addresses on m68k
+ * (so "laddr" is a bit misleading) */
+ dma_addr_t descriptors_laddr;
+ u32 cda_laddr; /* logical DMA address of CDA */
+ u32 tda_laddr; /* logical DMA address of TDA */
+ u32 rra_laddr; /* logical DMA address of RRA */
+ u32 rda_laddr; /* logical DMA address of RDA */
+ dma_addr_t rx_laddr[SONIC_NUM_RRS]; /* logical DMA addresses of rx skbuffs */
+ dma_addr_t tx_laddr[SONIC_NUM_TDS]; /* logical DMA addresses of tx skbuffs */
+ unsigned int rra_end;
+ unsigned int cur_rwp;
unsigned int cur_rx;
- unsigned int cur_tx;
- unsigned int dirty_tx; /* last unacked transmit packet */
- char tx_full;
+ unsigned int cur_tx; /* first unacked transmit packet */
+ unsigned int eol_rx;
+ unsigned int eol_tx; /* last unacked transmit packet */
+ unsigned int next_tx; /* next free TD */
+ struct device *device; /* generic device */
struct net_device_stats stats;
};
-#define TX_TIMEOUT 6
+#define TX_TIMEOUT (3 * HZ)
/* Index to functions, as function prototypes. */
@@ -477,6 +337,114 @@
static int sonic_init(struct net_device *dev);
static void sonic_tx_timeout(struct net_device *dev);
+/* Internal inlines for reading/writing DMA buffers. Note that bus
+ size and endianness matter here, whereas they don't for registers,
+ as far as we can tell. */
+/* OpenBSD calls this "SWO". I'd like to think that sonic_buf_put()
+ is a much better name. */
+static inline void sonic_buf_put(void* base, int bitmode,
+ int offset, __u16 val)
+{
+ if (bitmode)
+#ifdef __BIG_ENDIAN
+ ((__u16 *) base + (offset*2))[1] = val;
+#else
+ ((__u16 *) base + (offset*2))[0] = val;
+#endif
+ else
+ ((__u16 *) base)[offset] = val;
+}
+
+static inline __u16 sonic_buf_get(void* base, int bitmode,
+ int offset)
+{
+ if (bitmode)
+#ifdef __BIG_ENDIAN
+ return ((volatile __u16 *) base + (offset*2))[1];
+#else
+ return ((volatile __u16 *) base + (offset*2))[0];
+#endif
+ else
+ return ((volatile __u16 *) base)[offset];
+}
+
+/* Inlines that you should actually use for reading/writing DMA buffers */
+static inline void sonic_cda_put(struct net_device* dev, int entry,
+ int offset, __u16 val)
+{
+ struct sonic_local* lp = (struct sonic_local *) dev->priv;
+ sonic_buf_put(lp->cda, lp->dma_bitmode,
+ (entry * SIZEOF_SONIC_CD) + offset, val);
+}
+
+static inline __u16 sonic_cda_get(struct net_device* dev, int entry,
+ int offset)
+{
+ struct sonic_local* lp = (struct sonic_local *) dev->priv;
+ return sonic_buf_get(lp->cda, lp->dma_bitmode,
+ (entry * SIZEOF_SONIC_CD) + offset);
+}
+
+static inline void sonic_set_cam_enable(struct net_device* dev, __u16 val)
+{
+ struct sonic_local* lp = (struct sonic_local *) dev->priv;
+ sonic_buf_put(lp->cda, lp->dma_bitmode, SONIC_CDA_CAM_ENABLE, val);
+}
+
+static inline __u16 sonic_get_cam_enable(struct net_device* dev)
+{
+ struct sonic_local* lp = (struct sonic_local *) dev->priv;
+ return sonic_buf_get(lp->cda, lp->dma_bitmode, SONIC_CDA_CAM_ENABLE);
+}
+
+static inline void sonic_tda_put(struct net_device* dev, int entry,
+ int offset, __u16 val)
+{
+ struct sonic_local* lp = (struct sonic_local *) dev->priv;
+ sonic_buf_put(lp->tda, lp->dma_bitmode,
+ (entry * SIZEOF_SONIC_TD) + offset, val);
+}
+
+static inline __u16 sonic_tda_get(struct net_device* dev, int entry,
+ int offset)
+{
+ struct sonic_local* lp = (struct sonic_local *) dev->priv;
+ return sonic_buf_get(lp->tda, lp->dma_bitmode,
+ (entry * SIZEOF_SONIC_TD) + offset);
+}
+
+static inline void sonic_rda_put(struct net_device* dev, int entry,
+ int offset, __u16 val)
+{
+ struct sonic_local* lp = (struct sonic_local *) dev->priv;
+ sonic_buf_put(lp->rda, lp->dma_bitmode,
+ (entry * SIZEOF_SONIC_RD) + offset, val);
+}
+
+static inline __u16 sonic_rda_get(struct net_device* dev, int entry,
+ int offset)
+{
+ struct sonic_local* lp = (struct sonic_local *) dev->priv;
+ return sonic_buf_get(lp->rda, lp->dma_bitmode,
+ (entry * SIZEOF_SONIC_RD) + offset);
+}
+
+static inline void sonic_rra_put(struct net_device* dev, int entry,
+ int offset, __u16 val)
+{
+ struct sonic_local* lp = (struct sonic_local *) dev->priv;
+ sonic_buf_put(lp->rra, lp->dma_bitmode,
+ (entry * SIZEOF_SONIC_RR) + offset, val);
+}
+
+static inline __u16 sonic_rra_get(struct net_device* dev, int entry,
+ int offset)
+{
+ struct sonic_local* lp = (struct sonic_local *) dev->priv;
+ return sonic_buf_get(lp->rra, lp->dma_bitmode,
+ (entry * SIZEOF_SONIC_RR) + offset);
+}
+
static const char *version =
"sonic.c:v0.92 20.9.98 tsbogend@alpha.franken.de\n";
diff --git a/drivers/net/tokenring/Kconfig b/drivers/net/tokenring/Kconfig
index 7e99e9f..e4cfc80 100644
--- a/drivers/net/tokenring/Kconfig
+++ b/drivers/net/tokenring/Kconfig
@@ -84,7 +84,7 @@
config TMS380TR
tristate "Generic TMS380 Token Ring ISA/PCI adapter support"
- depends on TR && (PCI || ISA && ISA_DMA_API)
+ depends on TR && (PCI || ISA && ISA_DMA_API || MCA)
select FW_LOADER
---help---
This driver provides generic support for token ring adapters
@@ -158,7 +158,7 @@
config MADGEMC
tristate "Madge Smart 16/4 Ringnode MicroChannel"
- depends on TR && TMS380TR && MCA_LEGACY
+ depends on TR && TMS380TR && MCA
help
This tms380 module supports the Madge Smart 16/4 MC16 and MC32
MicroChannel adapters.
diff --git a/drivers/net/tokenring/abyss.c b/drivers/net/tokenring/abyss.c
index 87103c4..9345e68 100644
--- a/drivers/net/tokenring/abyss.c
+++ b/drivers/net/tokenring/abyss.c
@@ -139,7 +139,7 @@
*/
dev->base_addr += 0x10;
- ret = tmsdev_init(dev, PCI_MAX_ADDRESS, pdev);
+ ret = tmsdev_init(dev, &pdev->dev);
if (ret) {
printk("%s: unable to get memory for dev->priv.\n",
dev->name);
diff --git a/drivers/net/tokenring/madgemc.c b/drivers/net/tokenring/madgemc.c
index 659cbdb..3a25d19 100644
--- a/drivers/net/tokenring/madgemc.c
+++ b/drivers/net/tokenring/madgemc.c
@@ -20,7 +20,7 @@
static const char version[] = "madgemc.c: v0.91 23/01/2000 by Adam Fritzler\n";
#include <linux/module.h>
-#include <linux/mca-legacy.h>
+#include <linux/mca.h>
#include <linux/kernel.h>
#include <linux/errno.h>
#include <linux/pci.h>
@@ -38,9 +38,7 @@
#define MADGEMC_IO_EXTENT 32
#define MADGEMC_SIF_OFFSET 0x08
-struct madgemc_card {
- struct net_device *dev;
-
+struct card_info {
/*
* These are read from the BIA ROM.
*/
@@ -57,16 +55,12 @@
unsigned int arblevel:4;
unsigned int ringspeed:2; /* 0 = 4mb, 1 = 16, 2 = Auto/none */
unsigned int cabletype:1; /* 0 = RJ45, 1 = DB9 */
-
- struct madgemc_card *next;
};
-static struct madgemc_card *madgemc_card_list;
-
static int madgemc_open(struct net_device *dev);
static int madgemc_close(struct net_device *dev);
static int madgemc_chipset_init(struct net_device *dev);
-static void madgemc_read_rom(struct madgemc_card *card);
+static void madgemc_read_rom(struct net_device *dev, struct card_info *card);
static unsigned short madgemc_setnselout_pins(struct net_device *dev);
static void madgemc_setcabletype(struct net_device *dev, int type);
@@ -151,261 +145,237 @@
-static int __init madgemc_probe(void)
+static int __devinit madgemc_probe(struct device *device)
{
static int versionprinted;
struct net_device *dev;
struct net_local *tp;
- struct madgemc_card *card;
- int i,slot = 0;
- __u8 posreg[4];
+ struct card_info *card;
+ struct mca_device *mdev = to_mca_device(device);
+ int ret = 0, i = 0;
- if (!MCA_bus)
- return -1;
-
- while (slot != MCA_NOTFOUND) {
- /*
- * Currently we only support the MC16/32 (MCA ID 002d)
- */
- slot = mca_find_unused_adapter(0x002d, slot);
- if (slot == MCA_NOTFOUND)
- break;
+ if (versionprinted++ == 0)
+ printk("%s", version);
- /*
- * If we get here, we have an adapter.
- */
- if (versionprinted++ == 0)
- printk("%s", version);
+ if(mca_device_claimed(mdev))
+ return -EBUSY;
+ mca_device_set_claim(mdev, 1);
- dev = alloc_trdev(sizeof(struct net_local));
- if (dev == NULL) {
- printk("madgemc: unable to allocate dev space\n");
- if (madgemc_card_list)
- return 0;
- return -1;
- }
+ dev = alloc_trdev(sizeof(struct net_local));
+ if (!dev) {
+ printk("madgemc: unable to allocate dev space\n");
+ mca_device_set_claim(mdev, 0);
+ ret = -ENOMEM;
+ goto getout;
+ }
- SET_MODULE_OWNER(dev);
- dev->dma = 0;
+ SET_MODULE_OWNER(dev);
+ dev->dma = 0;
- /*
- * Fetch MCA config registers
- */
- for(i=0;i<4;i++)
- posreg[i] = mca_read_stored_pos(slot, i+2);
-
- card = kmalloc(sizeof(struct madgemc_card), GFP_KERNEL);
- if (card==NULL) {
- printk("madgemc: unable to allocate card struct\n");
- free_netdev(dev);
- if (madgemc_card_list)
- return 0;
- return -1;
- }
- card->dev = dev;
+ card = kmalloc(sizeof(struct card_info), GFP_KERNEL);
+ if (card==NULL) {
+ printk("madgemc: unable to allocate card struct\n");
+ ret = -ENOMEM;
+ goto getout1;
+ }
- /*
- * Parse configuration information. This all comes
- * directly from the publicly available @002d.ADF.
- * Get it from Madge or your local ADF library.
- */
+ /*
+ * Parse configuration information. This all comes
+ * directly from the publicly available @002d.ADF.
+ * Get it from Madge or your local ADF library.
+ */
- /*
- * Base address
- */
- dev->base_addr = 0x0a20 +
- ((posreg[2] & MC16_POS2_ADDR2)?0x0400:0) +
- ((posreg[0] & MC16_POS0_ADDR1)?0x1000:0) +
- ((posreg[3] & MC16_POS3_ADDR3)?0x2000:0);
+ /*
+ * Base address
+ */
+ dev->base_addr = 0x0a20 +
+ ((mdev->pos[2] & MC16_POS2_ADDR2)?0x0400:0) +
+ ((mdev->pos[0] & MC16_POS0_ADDR1)?0x1000:0) +
+ ((mdev->pos[3] & MC16_POS3_ADDR3)?0x2000:0);
- /*
- * Interrupt line
- */
- switch(posreg[0] >> 6) { /* upper two bits */
+ /*
+ * Interrupt line
+ */
+ switch(mdev->pos[0] >> 6) { /* upper two bits */
case 0x1: dev->irq = 3; break;
case 0x2: dev->irq = 9; break; /* IRQ 2 = IRQ 9 */
case 0x3: dev->irq = 10; break;
default: dev->irq = 0; break;
- }
+ }
- if (dev->irq == 0) {
- printk("%s: invalid IRQ\n", dev->name);
- goto getout1;
- }
+ if (dev->irq == 0) {
+ printk("%s: invalid IRQ\n", dev->name);
+ ret = -EBUSY;
+ goto getout2;
+ }
- if (!request_region(dev->base_addr, MADGEMC_IO_EXTENT,
- "madgemc")) {
- printk(KERN_INFO "madgemc: unable to setup Smart MC in slot %d because of I/O base conflict at 0x%04lx\n", slot, dev->base_addr);
- dev->base_addr += MADGEMC_SIF_OFFSET;
- goto getout1;
- }
+ if (!request_region(dev->base_addr, MADGEMC_IO_EXTENT,
+ "madgemc")) {
+ printk(KERN_INFO "madgemc: unable to setup Smart MC in slot %d because of I/O base conflict at 0x%04lx\n", mdev->slot, dev->base_addr);
dev->base_addr += MADGEMC_SIF_OFFSET;
+ ret = -EBUSY;
+ goto getout2;
+ }
+ dev->base_addr += MADGEMC_SIF_OFFSET;
+
+ /*
+ * Arbitration Level
+ */
+ card->arblevel = ((mdev->pos[0] >> 1) & 0x7) + 8;
+
+ /*
+ * Burst mode and Fairness
+ */
+ card->burstmode = ((mdev->pos[2] >> 6) & 0x3);
+ card->fairness = ((mdev->pos[2] >> 4) & 0x1);
+
+ /*
+ * Ring Speed
+ */
+ if ((mdev->pos[1] >> 2)&0x1)
+ card->ringspeed = 2; /* not selected */
+ else if ((mdev->pos[2] >> 5) & 0x1)
+ card->ringspeed = 1; /* 16Mb */
+ else
+ card->ringspeed = 0; /* 4Mb */
+
+ /*
+ * Cable type
+ */
+ if ((mdev->pos[1] >> 6)&0x1)
+ card->cabletype = 1; /* STP/DB9 */
+ else
+ card->cabletype = 0; /* UTP/RJ-45 */
+
+
+ /*
+ * ROM Info. This requires us to actually twiddle
+ * bits on the card, so we must ensure above that
+ * the base address is free of conflict (request_region above).
+ */
+ madgemc_read_rom(dev, card);
- /*
- * Arbitration Level
- */
- card->arblevel = ((posreg[0] >> 1) & 0x7) + 8;
-
- /*
- * Burst mode and Fairness
- */
- card->burstmode = ((posreg[2] >> 6) & 0x3);
- card->fairness = ((posreg[2] >> 4) & 0x1);
-
- /*
- * Ring Speed
- */
- if ((posreg[1] >> 2)&0x1)
- card->ringspeed = 2; /* not selected */
- else if ((posreg[2] >> 5) & 0x1)
- card->ringspeed = 1; /* 16Mb */
- else
- card->ringspeed = 0; /* 4Mb */
-
- /*
- * Cable type
- */
- if ((posreg[1] >> 6)&0x1)
- card->cabletype = 1; /* STP/DB9 */
- else
- card->cabletype = 0; /* UTP/RJ-45 */
-
-
- /*
- * ROM Info. This requires us to actually twiddle
- * bits on the card, so we must ensure above that
- * the base address is free of conflict (request_region above).
- */
- madgemc_read_rom(card);
+ if (card->manid != 0x4d) { /* something went wrong */
+ printk(KERN_INFO "%s: Madge MC ROM read failed (unknown manufacturer ID %02x)\n", dev->name, card->manid);
+ goto getout3;
+ }
- if (card->manid != 0x4d) { /* something went wrong */
- printk(KERN_INFO "%s: Madge MC ROM read failed (unknown manufacturer ID %02x)\n", dev->name, card->manid);
- goto getout;
- }
-
- if ((card->cardtype != 0x08) && (card->cardtype != 0x0d)) {
- printk(KERN_INFO "%s: Madge MC ROM read failed (unknown card ID %02x)\n", dev->name, card->cardtype);
- goto getout;
- }
+ if ((card->cardtype != 0x08) && (card->cardtype != 0x0d)) {
+ printk(KERN_INFO "%s: Madge MC ROM read failed (unknown card ID %02x)\n", dev->name, card->cardtype);
+ ret = -EIO;
+ goto getout3;
+ }
- /* All cards except Rev 0 and 1 MC16's have 256kb of RAM */
- if ((card->cardtype == 0x08) && (card->cardrev <= 0x01))
- card->ramsize = 128;
- else
- card->ramsize = 256;
+ /* All cards except Rev 0 and 1 MC16's have 256kb of RAM */
+ if ((card->cardtype == 0x08) && (card->cardrev <= 0x01))
+ card->ramsize = 128;
+ else
+ card->ramsize = 256;
- printk("%s: %s Rev %d at 0x%04lx IRQ %d\n",
- dev->name,
- (card->cardtype == 0x08)?MADGEMC16_CARDNAME:
- MADGEMC32_CARDNAME, card->cardrev,
- dev->base_addr, dev->irq);
+ printk("%s: %s Rev %d at 0x%04lx IRQ %d\n",
+ dev->name,
+ (card->cardtype == 0x08)?MADGEMC16_CARDNAME:
+ MADGEMC32_CARDNAME, card->cardrev,
+ dev->base_addr, dev->irq);
- if (card->cardtype == 0x0d)
- printk("%s: Warning: MC32 support is experimental and highly untested\n", dev->name);
+ if (card->cardtype == 0x0d)
+ printk("%s: Warning: MC32 support is experimental and highly untested\n", dev->name);
+
+ if (card->ringspeed==2) { /* Unknown */
+ printk("%s: Warning: Ring speed not set in POS -- Please run the reference disk and set it!\n", dev->name);
+ card->ringspeed = 1; /* default to 16mb */
+ }
- if (card->ringspeed==2) { /* Unknown */
- printk("%s: Warning: Ring speed not set in POS -- Please run the reference disk and set it!\n", dev->name);
- card->ringspeed = 1; /* default to 16mb */
- }
-
- printk("%s: RAM Size: %dKB\n", dev->name, card->ramsize);
+ printk("%s: RAM Size: %dKB\n", dev->name, card->ramsize);
- printk("%s: Ring Speed: %dMb/sec on %s\n", dev->name,
- (card->ringspeed)?16:4,
- card->cabletype?"STP/DB9":"UTP/RJ-45");
- printk("%s: Arbitration Level: %d\n", dev->name,
- card->arblevel);
+ printk("%s: Ring Speed: %dMb/sec on %s\n", dev->name,
+ (card->ringspeed)?16:4,
+ card->cabletype?"STP/DB9":"UTP/RJ-45");
+ printk("%s: Arbitration Level: %d\n", dev->name,
+ card->arblevel);
- printk("%s: Burst Mode: ", dev->name);
- switch(card->burstmode) {
+ printk("%s: Burst Mode: ", dev->name);
+ switch(card->burstmode) {
case 0: printk("Cycle steal"); break;
case 1: printk("Limited burst"); break;
case 2: printk("Delayed release"); break;
case 3: printk("Immediate release"); break;
- }
- printk(" (%s)\n", (card->fairness)?"Unfair":"Fair");
+ }
+ printk(" (%s)\n", (card->fairness)?"Unfair":"Fair");
- /*
- * Enable SIF before we assign the interrupt handler,
- * just in case we get spurious interrupts that need
- * handling.
- */
- outb(0, dev->base_addr + MC_CONTROL_REG0); /* sanity */
- madgemc_setsifsel(dev, 1);
- if (request_irq(dev->irq, madgemc_interrupt, SA_SHIRQ,
- "madgemc", dev))
- goto getout;
-
- madgemc_chipset_init(dev); /* enables interrupts! */
- madgemc_setcabletype(dev, card->cabletype);
-
- /* Setup MCA structures */
- mca_set_adapter_name(slot, (card->cardtype == 0x08)?MADGEMC16_CARDNAME:MADGEMC32_CARDNAME);
- mca_set_adapter_procfn(slot, madgemc_mcaproc, dev);
- mca_mark_as_used(slot);
-
- printk("%s: Ring Station Address: ", dev->name);
- printk("%2.2x", dev->dev_addr[0]);
- for (i = 1; i < 6; i++)
- printk(":%2.2x", dev->dev_addr[i]);
- printk("\n");
-
- /* XXX is ISA_MAX_ADDRESS correct here? */
- if (tmsdev_init(dev, ISA_MAX_ADDRESS, NULL)) {
- printk("%s: unable to get memory for dev->priv.\n",
- dev->name);
- release_region(dev->base_addr-MADGEMC_SIF_OFFSET,
- MADGEMC_IO_EXTENT);
-
- kfree(card);
- tmsdev_term(dev);
- free_netdev(dev);
- if (madgemc_card_list)
- return 0;
- return -1;
- }
- tp = netdev_priv(dev);
-
- /*
- * The MC16 is physically a 32bit card. However, Madge
- * insists on calling it 16bit, so I'll assume here that
- * they know what they're talking about. Cut off DMA
- * at 16mb.
- */
- tp->setnselout = madgemc_setnselout_pins;
- tp->sifwriteb = madgemc_sifwriteb;
- tp->sifreadb = madgemc_sifreadb;
- tp->sifwritew = madgemc_sifwritew;
- tp->sifreadw = madgemc_sifreadw;
- tp->DataRate = (card->ringspeed)?SPEED_16:SPEED_4;
-
- memcpy(tp->ProductID, "Madge MCA 16/4 ", PROD_ID_SIZE + 1);
-
- dev->open = madgemc_open;
- dev->stop = madgemc_close;
-
- if (register_netdev(dev) == 0) {
- /* Enlist in the card list */
- card->next = madgemc_card_list;
- madgemc_card_list = card;
- slot++;
- continue; /* successful, try to find another */
- }
-
- free_irq(dev->irq, dev);
- getout:
- release_region(dev->base_addr-MADGEMC_SIF_OFFSET,
- MADGEMC_IO_EXTENT);
- getout1:
- kfree(card);
- free_netdev(dev);
- slot++;
+ /*
+ * Enable SIF before we assign the interrupt handler,
+ * just in case we get spurious interrupts that need
+ * handling.
+ */
+ outb(0, dev->base_addr + MC_CONTROL_REG0); /* sanity */
+ madgemc_setsifsel(dev, 1);
+ if (request_irq(dev->irq, madgemc_interrupt, SA_SHIRQ,
+ "madgemc", dev)) {
+ ret = -EBUSY;
+ goto getout3;
}
- if (madgemc_card_list)
+ madgemc_chipset_init(dev); /* enables interrupts! */
+ madgemc_setcabletype(dev, card->cabletype);
+
+ /* Setup MCA structures */
+ mca_device_set_name(mdev, (card->cardtype == 0x08)?MADGEMC16_CARDNAME:MADGEMC32_CARDNAME);
+ mca_set_adapter_procfn(mdev->slot, madgemc_mcaproc, dev);
+
+ printk("%s: Ring Station Address: ", dev->name);
+ printk("%2.2x", dev->dev_addr[0]);
+ for (i = 1; i < 6; i++)
+ printk(":%2.2x", dev->dev_addr[i]);
+ printk("\n");
+
+ if (tmsdev_init(dev, device)) {
+ printk("%s: unable to get memory for dev->priv.\n",
+ dev->name);
+ ret = -ENOMEM;
+ goto getout4;
+ }
+ tp = netdev_priv(dev);
+
+ /*
+ * The MC16 is physically a 32bit card. However, Madge
+ * insists on calling it 16bit, so I'll assume here that
+ * they know what they're talking about. Cut off DMA
+ * at 16mb.
+ */
+ tp->setnselout = madgemc_setnselout_pins;
+ tp->sifwriteb = madgemc_sifwriteb;
+ tp->sifreadb = madgemc_sifreadb;
+ tp->sifwritew = madgemc_sifwritew;
+ tp->sifreadw = madgemc_sifreadw;
+ tp->DataRate = (card->ringspeed)?SPEED_16:SPEED_4;
+
+ memcpy(tp->ProductID, "Madge MCA 16/4 ", PROD_ID_SIZE + 1);
+
+ dev->open = madgemc_open;
+ dev->stop = madgemc_close;
+
+ tp->tmspriv = card;
+ dev_set_drvdata(device, dev);
+
+ if (register_netdev(dev) == 0)
return 0;
- return -1;
+
+ dev_set_drvdata(device, NULL);
+ ret = -ENOMEM;
+getout4:
+ free_irq(dev->irq, dev);
+getout3:
+ release_region(dev->base_addr-MADGEMC_SIF_OFFSET,
+ MADGEMC_IO_EXTENT);
+getout2:
+ kfree(card);
+getout1:
+ free_netdev(dev);
+getout:
+ mca_device_set_claim(mdev, 0);
+ return ret;
}
/*
@@ -664,12 +634,12 @@
* is complete.
*
*/
-static void madgemc_read_rom(struct madgemc_card *card)
+static void madgemc_read_rom(struct net_device *dev, struct card_info *card)
{
unsigned long ioaddr;
unsigned char reg0, reg1, tmpreg0, i;
- ioaddr = card->dev->base_addr;
+ ioaddr = dev->base_addr;
reg0 = inb(ioaddr + MC_CONTROL_REG0);
reg1 = inb(ioaddr + MC_CONTROL_REG1);
@@ -686,9 +656,9 @@
outb(tmpreg0 | MC_CONTROL_REG0_PAGE, ioaddr + MC_CONTROL_REG0);
/* Read BIA */
- card->dev->addr_len = 6;
+ dev->addr_len = 6;
for (i = 0; i < 6; i++)
- card->dev->dev_addr[i] = inb(ioaddr + MC_ROM_BIA_START + i);
+ dev->dev_addr[i] = inb(ioaddr + MC_ROM_BIA_START + i);
/* Restore original register values */
outb(reg0, ioaddr + MC_CONTROL_REG0);
@@ -721,14 +691,10 @@
static int madgemc_mcaproc(char *buf, int slot, void *d)
{
struct net_device *dev = (struct net_device *)d;
- struct madgemc_card *curcard = madgemc_card_list;
+ struct net_local *tp = dev->priv;
+ struct card_info *curcard = tp->tmspriv;
int len = 0;
- while (curcard) { /* search for card struct */
- if (curcard->dev == dev)
- break;
- curcard = curcard->next;
- }
len += sprintf(buf+len, "-------\n");
if (curcard) {
struct net_local *tp = netdev_priv(dev);
@@ -763,25 +729,56 @@
return len;
}
-static void __exit madgemc_exit(void)
+static int __devexit madgemc_remove(struct device *device)
{
- struct net_device *dev;
- struct madgemc_card *this_card;
-
- while (madgemc_card_list) {
- dev = madgemc_card_list->dev;
- unregister_netdev(dev);
- release_region(dev->base_addr-MADGEMC_SIF_OFFSET, MADGEMC_IO_EXTENT);
- free_irq(dev->irq, dev);
- tmsdev_term(dev);
- free_netdev(dev);
- this_card = madgemc_card_list;
- madgemc_card_list = this_card->next;
- kfree(this_card);
- }
+ struct net_device *dev = dev_get_drvdata(device);
+ struct net_local *tp;
+ struct card_info *card;
+
+ if (!dev)
+ BUG();
+
+ tp = dev->priv;
+ card = tp->tmspriv;
+ kfree(card);
+ tp->tmspriv = NULL;
+
+ unregister_netdev(dev);
+ release_region(dev->base_addr-MADGEMC_SIF_OFFSET, MADGEMC_IO_EXTENT);
+ free_irq(dev->irq, dev);
+ tmsdev_term(dev);
+ free_netdev(dev);
+ dev_set_drvdata(device, NULL);
+
+ return 0;
}
-module_init(madgemc_probe);
+static short madgemc_adapter_ids[] __initdata = {
+ 0x002d,
+ 0x0000
+};
+
+static struct mca_driver madgemc_driver = {
+ .id_table = madgemc_adapter_ids,
+ .driver = {
+ .name = "madgemc",
+ .bus = &mca_bus_type,
+ .probe = madgemc_probe,
+ .remove = __devexit_p(madgemc_remove),
+ },
+};
+
+static int __init madgemc_init (void)
+{
+ return mca_register_driver (&madgemc_driver);
+}
+
+static void __exit madgemc_exit (void)
+{
+ mca_unregister_driver (&madgemc_driver);
+}
+
+module_init(madgemc_init);
module_exit(madgemc_exit);
MODULE_LICENSE("GPL");
diff --git a/drivers/net/tokenring/proteon.c b/drivers/net/tokenring/proteon.c
index 40ad0fd..eb1423e 100644
--- a/drivers/net/tokenring/proteon.c
+++ b/drivers/net/tokenring/proteon.c
@@ -62,8 +62,7 @@
};
static char cardname[] = "Proteon 1392\0";
-
-struct net_device *proteon_probe(int unit);
+static u64 dma_mask = ISA_MAX_ADDRESS;
static int proteon_open(struct net_device *dev);
static void proteon_read_eeprom(struct net_device *dev);
static unsigned short proteon_setnselout_pins(struct net_device *dev);
@@ -116,7 +115,7 @@
return -ENODEV;
}
-static int __init setup_card(struct net_device *dev)
+static int __init setup_card(struct net_device *dev, struct device *pdev)
{
struct net_local *tp;
static int versionprinted;
@@ -137,7 +136,7 @@
}
}
if (err)
- goto out4;
+ goto out5;
/* At this point we have found a valid card. */
@@ -145,14 +144,15 @@
printk(KERN_DEBUG "%s", version);
err = -EIO;
- if (tmsdev_init(dev, ISA_MAX_ADDRESS, NULL))
+ pdev->dma_mask = &dma_mask;
+ if (tmsdev_init(dev, pdev))
goto out4;
dev->base_addr &= ~3;
proteon_read_eeprom(dev);
- printk(KERN_DEBUG "%s: Ring Station Address: ", dev->name);
+ printk(KERN_DEBUG "proteon.c: Ring Station Address: ");
printk("%2.2x", dev->dev_addr[0]);
for (j = 1; j < 6; j++)
printk(":%2.2x", dev->dev_addr[j]);
@@ -185,7 +185,7 @@
if(irqlist[j] == 0)
{
- printk(KERN_INFO "%s: AutoSelect no IRQ available\n", dev->name);
+ printk(KERN_INFO "proteon.c: AutoSelect no IRQ available\n");
goto out3;
}
}
@@ -196,15 +196,15 @@
break;
if (irqlist[j] == 0)
{
- printk(KERN_INFO "%s: Illegal IRQ %d specified\n",
- dev->name, dev->irq);
+ printk(KERN_INFO "proteon.c: Illegal IRQ %d specified\n",
+ dev->irq);
goto out3;
}
if (request_irq(dev->irq, tms380tr_interrupt, 0,
cardname, dev))
{
- printk(KERN_INFO "%s: Selected IRQ %d not available\n",
- dev->name, dev->irq);
+ printk(KERN_INFO "proteon.c: Selected IRQ %d not available\n",
+ dev->irq);
goto out3;
}
}
@@ -220,7 +220,7 @@
if(dmalist[j] == 0)
{
- printk(KERN_INFO "%s: AutoSelect no DMA available\n", dev->name);
+ printk(KERN_INFO "proteon.c: AutoSelect no DMA available\n");
goto out2;
}
}
@@ -231,25 +231,25 @@
break;
if (dmalist[j] == 0)
{
- printk(KERN_INFO "%s: Illegal DMA %d specified\n",
- dev->name, dev->dma);
+ printk(KERN_INFO "proteon.c: Illegal DMA %d specified\n",
+ dev->dma);
goto out2;
}
if (request_dma(dev->dma, cardname))
{
- printk(KERN_INFO "%s: Selected DMA %d not available\n",
- dev->name, dev->dma);
+ printk(KERN_INFO "proteon.c: Selected DMA %d not available\n",
+ dev->dma);
goto out2;
}
}
- printk(KERN_DEBUG "%s: IO: %#4lx IRQ: %d DMA: %d\n",
- dev->name, dev->base_addr, dev->irq, dev->dma);
-
err = register_netdev(dev);
if (err)
goto out;
+ printk(KERN_DEBUG "%s: IO: %#4lx IRQ: %d DMA: %d\n",
+ dev->name, dev->base_addr, dev->irq, dev->dma);
+
return 0;
out:
free_dma(dev->dma);
@@ -258,34 +258,11 @@
out3:
tmsdev_term(dev);
out4:
- release_region(dev->base_addr, PROTEON_IO_EXTENT);
+ release_region(dev->base_addr, PROTEON_IO_EXTENT);
+out5:
return err;
}
-struct net_device * __init proteon_probe(int unit)
-{
- struct net_device *dev = alloc_trdev(sizeof(struct net_local));
- int err = 0;
-
- if (!dev)
- return ERR_PTR(-ENOMEM);
-
- if (unit >= 0) {
- sprintf(dev->name, "tr%d", unit);
- netdev_boot_setup_check(dev);
- }
-
- err = setup_card(dev);
- if (err)
- goto out;
-
- return dev;
-
-out:
- free_netdev(dev);
- return ERR_PTR(err);
-}
-
/*
* Reads MAC address from adapter RAM, which should've read it from
* the onboard ROM.
@@ -352,8 +329,6 @@
return tms380tr_open(dev);
}
-#ifdef MODULE
-
#define ISATR_MAX_ADAPTERS 3
static int io[ISATR_MAX_ADAPTERS];
@@ -366,13 +341,23 @@
module_param_array(irq, int, NULL, 0);
module_param_array(dma, int, NULL, 0);
-static struct net_device *proteon_dev[ISATR_MAX_ADAPTERS];
+static struct platform_device *proteon_dev[ISATR_MAX_ADAPTERS];
-int init_module(void)
+static struct device_driver proteon_driver = {
+ .name = "proteon",
+ .bus = &platform_bus_type,
+};
+
+static int __init proteon_init(void)
{
struct net_device *dev;
+ struct platform_device *pdev;
int i, num = 0, err = 0;
+ err = driver_register(&proteon_driver);
+ if (err)
+ return err;
+
for (i = 0; i < ISATR_MAX_ADAPTERS ; i++) {
dev = alloc_trdev(sizeof(struct net_local));
if (!dev)
@@ -381,11 +366,15 @@
dev->base_addr = io[i];
dev->irq = irq[i];
dev->dma = dma[i];
- err = setup_card(dev);
+ pdev = platform_device_register_simple("proteon",
+ i, NULL, 0);
+ err = setup_card(dev, &pdev->dev);
if (!err) {
- proteon_dev[i] = dev;
+ proteon_dev[i] = pdev;
+ dev_set_drvdata(&pdev->dev, dev);
++num;
} else {
+ platform_device_unregister(pdev);
free_netdev(dev);
}
}
@@ -399,23 +388,28 @@
return (0);
}
-void cleanup_module(void)
+static void __exit proteon_cleanup(void)
{
+ struct net_device *dev;
int i;
for (i = 0; i < ISATR_MAX_ADAPTERS ; i++) {
- struct net_device *dev = proteon_dev[i];
+ struct platform_device *pdev = proteon_dev[i];
- if (!dev)
+ if (!pdev)
continue;
-
+ dev = dev_get_drvdata(&pdev->dev);
unregister_netdev(dev);
release_region(dev->base_addr, PROTEON_IO_EXTENT);
free_irq(dev->irq, dev);
free_dma(dev->dma);
tmsdev_term(dev);
free_netdev(dev);
+ dev_set_drvdata(&pdev->dev, NULL);
+ platform_device_unregister(pdev);
}
+ driver_unregister(&proteon_driver);
}
-#endif /* MODULE */
+module_init(proteon_init);
+module_exit(proteon_cleanup);
diff --git a/drivers/net/tokenring/skisa.c b/drivers/net/tokenring/skisa.c
index f26796e..3c7c662 100644
--- a/drivers/net/tokenring/skisa.c
+++ b/drivers/net/tokenring/skisa.c
@@ -68,8 +68,7 @@
};
static char isa_cardname[] = "SK NET TR 4/16 ISA\0";
-
-struct net_device *sk_isa_probe(int unit);
+static u64 dma_mask = ISA_MAX_ADDRESS;
static int sk_isa_open(struct net_device *dev);
static void sk_isa_read_eeprom(struct net_device *dev);
static unsigned short sk_isa_setnselout_pins(struct net_device *dev);
@@ -133,7 +132,7 @@
return 0;
}
-static int __init setup_card(struct net_device *dev)
+static int __init setup_card(struct net_device *dev, struct device *pdev)
{
struct net_local *tp;
static int versionprinted;
@@ -154,7 +153,7 @@
}
}
if (err)
- goto out4;
+ goto out5;
/* At this point we have found a valid card. */
@@ -162,14 +161,15 @@
printk(KERN_DEBUG "%s", version);
err = -EIO;
- if (tmsdev_init(dev, ISA_MAX_ADDRESS, NULL))
+ pdev->dma_mask = &dma_mask;
+ if (tmsdev_init(dev, pdev))
goto out4;
dev->base_addr &= ~3;
sk_isa_read_eeprom(dev);
- printk(KERN_DEBUG "%s: Ring Station Address: ", dev->name);
+ printk(KERN_DEBUG "skisa.c: Ring Station Address: ");
printk("%2.2x", dev->dev_addr[0]);
for (j = 1; j < 6; j++)
printk(":%2.2x", dev->dev_addr[j]);
@@ -202,7 +202,7 @@
if(irqlist[j] == 0)
{
- printk(KERN_INFO "%s: AutoSelect no IRQ available\n", dev->name);
+ printk(KERN_INFO "skisa.c: AutoSelect no IRQ available\n");
goto out3;
}
}
@@ -213,15 +213,15 @@
break;
if (irqlist[j] == 0)
{
- printk(KERN_INFO "%s: Illegal IRQ %d specified\n",
- dev->name, dev->irq);
+ printk(KERN_INFO "skisa.c: Illegal IRQ %d specified\n",
+ dev->irq);
goto out3;
}
if (request_irq(dev->irq, tms380tr_interrupt, 0,
isa_cardname, dev))
{
- printk(KERN_INFO "%s: Selected IRQ %d not available\n",
- dev->name, dev->irq);
+ printk(KERN_INFO "skisa.c: Selected IRQ %d not available\n",
+ dev->irq);
goto out3;
}
}
@@ -237,7 +237,7 @@
if(dmalist[j] == 0)
{
- printk(KERN_INFO "%s: AutoSelect no DMA available\n", dev->name);
+ printk(KERN_INFO "skisa.c: AutoSelect no DMA available\n");
goto out2;
}
}
@@ -248,25 +248,25 @@
break;
if (dmalist[j] == 0)
{
- printk(KERN_INFO "%s: Illegal DMA %d specified\n",
- dev->name, dev->dma);
+ printk(KERN_INFO "skisa.c: Illegal DMA %d specified\n",
+ dev->dma);
goto out2;
}
if (request_dma(dev->dma, isa_cardname))
{
- printk(KERN_INFO "%s: Selected DMA %d not available\n",
- dev->name, dev->dma);
+ printk(KERN_INFO "skisa.c: Selected DMA %d not available\n",
+ dev->dma);
goto out2;
}
}
- printk(KERN_DEBUG "%s: IO: %#4lx IRQ: %d DMA: %d\n",
- dev->name, dev->base_addr, dev->irq, dev->dma);
-
err = register_netdev(dev);
if (err)
goto out;
+ printk(KERN_DEBUG "%s: IO: %#4lx IRQ: %d DMA: %d\n",
+ dev->name, dev->base_addr, dev->irq, dev->dma);
+
return 0;
out:
free_dma(dev->dma);
@@ -275,33 +275,11 @@
out3:
tmsdev_term(dev);
out4:
- release_region(dev->base_addr, SK_ISA_IO_EXTENT);
+ release_region(dev->base_addr, SK_ISA_IO_EXTENT);
+out5:
return err;
}
-struct net_device * __init sk_isa_probe(int unit)
-{
- struct net_device *dev = alloc_trdev(sizeof(struct net_local));
- int err = 0;
-
- if (!dev)
- return ERR_PTR(-ENOMEM);
-
- if (unit >= 0) {
- sprintf(dev->name, "tr%d", unit);
- netdev_boot_setup_check(dev);
- }
-
- err = setup_card(dev);
- if (err)
- goto out;
-
- return dev;
-out:
- free_netdev(dev);
- return ERR_PTR(err);
-}
-
/*
* Reads MAC address from adapter RAM, which should've read it from
* the onboard ROM.
@@ -361,8 +339,6 @@
return tms380tr_open(dev);
}
-#ifdef MODULE
-
#define ISATR_MAX_ADAPTERS 3
static int io[ISATR_MAX_ADAPTERS];
@@ -375,13 +351,23 @@
module_param_array(irq, int, NULL, 0);
module_param_array(dma, int, NULL, 0);
-static struct net_device *sk_isa_dev[ISATR_MAX_ADAPTERS];
+static struct platform_device *sk_isa_dev[ISATR_MAX_ADAPTERS];
-int init_module(void)
+static struct device_driver sk_isa_driver = {
+ .name = "skisa",
+ .bus = &platform_bus_type,
+};
+
+static int __init sk_isa_init(void)
{
struct net_device *dev;
+ struct platform_device *pdev;
int i, num = 0, err = 0;
+ err = driver_register(&sk_isa_driver);
+ if (err)
+ return err;
+
for (i = 0; i < ISATR_MAX_ADAPTERS ; i++) {
dev = alloc_trdev(sizeof(struct net_local));
if (!dev)
@@ -390,12 +376,15 @@
dev->base_addr = io[i];
dev->irq = irq[i];
dev->dma = dma[i];
- err = setup_card(dev);
-
+ pdev = platform_device_register_simple("skisa",
+ i, NULL, 0);
+ err = setup_card(dev, &pdev->dev);
if (!err) {
- sk_isa_dev[i] = dev;
+ sk_isa_dev[i] = pdev;
+ dev_set_drvdata(&sk_isa_dev[i]->dev, dev);
++num;
} else {
+ platform_device_unregister(pdev);
free_netdev(dev);
}
}
@@ -409,23 +398,28 @@
return (0);
}
-void cleanup_module(void)
+static void __exit sk_isa_cleanup(void)
{
+ struct net_device *dev;
int i;
for (i = 0; i < ISATR_MAX_ADAPTERS ; i++) {
- struct net_device *dev = sk_isa_dev[i];
+ struct platform_device *pdev = sk_isa_dev[i];
- if (!dev)
+ if (!pdev)
continue;
-
+ dev = dev_get_drvdata(&pdev->dev);
unregister_netdev(dev);
release_region(dev->base_addr, SK_ISA_IO_EXTENT);
free_irq(dev->irq, dev);
free_dma(dev->dma);
tmsdev_term(dev);
free_netdev(dev);
+ dev_set_drvdata(&pdev->dev, NULL);
+ platform_device_unregister(pdev);
}
+ driver_unregister(&sk_isa_driver);
}
-#endif /* MODULE */
+module_init(sk_isa_init);
+module_exit(sk_isa_cleanup);
diff --git a/drivers/net/tokenring/tms380tr.c b/drivers/net/tokenring/tms380tr.c
index 5e0b0ce..2e39bf1 100644
--- a/drivers/net/tokenring/tms380tr.c
+++ b/drivers/net/tokenring/tms380tr.c
@@ -62,6 +62,7 @@
* normal operation.
* 30-Dec-02 JF Removed incorrect __init from
* tms380tr_init_card.
+ * 22-Jul-05 JF Converted to dma-mapping.
*
* To do:
* 1. Multi/Broadcast packet handling (this may have fixed itself)
@@ -89,7 +90,7 @@
#include <linux/time.h>
#include <linux/errno.h>
#include <linux/init.h>
-#include <linux/pci.h>
+#include <linux/dma-mapping.h>
#include <linux/delay.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
@@ -114,8 +115,6 @@
#endif
static unsigned int tms380tr_debug = TMS380TR_DEBUG;
-static struct device tms_device;
-
/* Index to functions, as function prototypes.
* Alphabetical by function name.
*/
@@ -434,7 +433,7 @@
skb_put(tp->Rpl[i].Skb, tp->MaxPacketSize);
/* data unreachable for DMA ? then use local buffer */
- dmabuf = pci_map_single(tp->pdev, tp->Rpl[i].Skb->data, tp->MaxPacketSize, PCI_DMA_FROMDEVICE);
+ dmabuf = dma_map_single(tp->pdev, tp->Rpl[i].Skb->data, tp->MaxPacketSize, DMA_FROM_DEVICE);
if(tp->dmalimit && (dmabuf + tp->MaxPacketSize > tp->dmalimit))
{
tp->Rpl[i].SkbStat = SKB_DATA_COPY;
@@ -638,10 +637,10 @@
/* Is buffer reachable for Busmaster-DMA? */
length = skb->len;
- dmabuf = pci_map_single(tp->pdev, skb->data, length, PCI_DMA_TODEVICE);
+ dmabuf = dma_map_single(tp->pdev, skb->data, length, DMA_TO_DEVICE);
if(tp->dmalimit && (dmabuf + length > tp->dmalimit)) {
/* Copy frame to local buffer */
- pci_unmap_single(tp->pdev, dmabuf, length, PCI_DMA_TODEVICE);
+ dma_unmap_single(tp->pdev, dmabuf, length, DMA_TO_DEVICE);
dmabuf = 0;
i = tp->TplFree->TPLIndex;
buf = tp->LocalTxBuffers[i];
@@ -1284,9 +1283,7 @@
unsigned short count, c, count2;
const struct firmware *fw_entry = NULL;
- strncpy(tms_device.bus_id,dev->name, BUS_ID_SIZE);
-
- if (request_firmware(&fw_entry, "tms380tr.bin", &tms_device) != 0) {
+ if (request_firmware(&fw_entry, "tms380tr.bin", tp->pdev) != 0) {
printk(KERN_ALERT "%s: firmware %s is missing, cannot start.\n",
dev->name, "tms380tr.bin");
return (-1);
@@ -2021,7 +2018,7 @@
printk(KERN_INFO "Cancel tx (%08lXh).\n", (unsigned long)tpl);
if (tpl->DMABuff)
- pci_unmap_single(tp->pdev, tpl->DMABuff, tpl->Skb->len, PCI_DMA_TODEVICE);
+ dma_unmap_single(tp->pdev, tpl->DMABuff, tpl->Skb->len, DMA_TO_DEVICE);
dev_kfree_skb_any(tpl->Skb);
}
@@ -2090,7 +2087,7 @@
tp->MacStat.tx_packets++;
if (tpl->DMABuff)
- pci_unmap_single(tp->pdev, tpl->DMABuff, tpl->Skb->len, PCI_DMA_TODEVICE);
+ dma_unmap_single(tp->pdev, tpl->DMABuff, tpl->Skb->len, DMA_TO_DEVICE);
dev_kfree_skb_irq(tpl->Skb);
tpl->BusyFlag = 0; /* "free" TPL */
}
@@ -2209,7 +2206,7 @@
tp->MacStat.rx_errors++;
}
if (rpl->DMABuff)
- pci_unmap_single(tp->pdev, rpl->DMABuff, tp->MaxPacketSize, PCI_DMA_TODEVICE);
+ dma_unmap_single(tp->pdev, rpl->DMABuff, tp->MaxPacketSize, DMA_TO_DEVICE);
rpl->DMABuff = 0;
/* Allocate new skb for rpl */
@@ -2227,7 +2224,7 @@
skb_put(rpl->Skb, tp->MaxPacketSize);
/* Data unreachable for DMA ? then use local buffer */
- dmabuf = pci_map_single(tp->pdev, rpl->Skb->data, tp->MaxPacketSize, PCI_DMA_FROMDEVICE);
+ dmabuf = dma_map_single(tp->pdev, rpl->Skb->data, tp->MaxPacketSize, DMA_FROM_DEVICE);
if(tp->dmalimit && (dmabuf + tp->MaxPacketSize > tp->dmalimit))
{
rpl->SkbStat = SKB_DATA_COPY;
@@ -2332,23 +2329,26 @@
struct net_local *tp;
tp = netdev_priv(dev);
- pci_unmap_single(tp->pdev, tp->dmabuffer, sizeof(struct net_local),
- PCI_DMA_BIDIRECTIONAL);
+ dma_unmap_single(tp->pdev, tp->dmabuffer, sizeof(struct net_local),
+ DMA_BIDIRECTIONAL);
}
-int tmsdev_init(struct net_device *dev, unsigned long dmalimit,
- struct pci_dev *pdev)
+int tmsdev_init(struct net_device *dev, struct device *pdev)
{
struct net_local *tms_local;
memset(dev->priv, 0, sizeof(struct net_local));
tms_local = netdev_priv(dev);
init_waitqueue_head(&tms_local->wait_for_tok_int);
- tms_local->dmalimit = dmalimit;
+ if (pdev->dma_mask)
+ tms_local->dmalimit = *pdev->dma_mask;
+ else
+ return -ENOMEM;
tms_local->pdev = pdev;
- tms_local->dmabuffer = pci_map_single(pdev, (void *)tms_local,
- sizeof(struct net_local), PCI_DMA_BIDIRECTIONAL);
- if (tms_local->dmabuffer + sizeof(struct net_local) > dmalimit)
+ tms_local->dmabuffer = dma_map_single(pdev, (void *)tms_local,
+ sizeof(struct net_local), DMA_BIDIRECTIONAL);
+ if (tms_local->dmabuffer + sizeof(struct net_local) >
+ tms_local->dmalimit)
{
printk(KERN_INFO "%s: Memory not accessible for DMA\n",
dev->name);
@@ -2370,8 +2370,6 @@
return 0;
}
-#ifdef MODULE
-
EXPORT_SYMBOL(tms380tr_open);
EXPORT_SYMBOL(tms380tr_close);
EXPORT_SYMBOL(tms380tr_interrupt);
@@ -2379,6 +2377,8 @@
EXPORT_SYMBOL(tmsdev_term);
EXPORT_SYMBOL(tms380tr_wait);
+#ifdef MODULE
+
static struct module *TMS380_module = NULL;
int init_module(void)
diff --git a/drivers/net/tokenring/tms380tr.h b/drivers/net/tokenring/tms380tr.h
index f2c5ba0..30452c6 100644
--- a/drivers/net/tokenring/tms380tr.h
+++ b/drivers/net/tokenring/tms380tr.h
@@ -17,8 +17,7 @@
int tms380tr_open(struct net_device *dev);
int tms380tr_close(struct net_device *dev);
irqreturn_t tms380tr_interrupt(int irq, void *dev_id, struct pt_regs *regs);
-int tmsdev_init(struct net_device *dev, unsigned long dmalimit,
- struct pci_dev *pdev);
+int tmsdev_init(struct net_device *dev, struct device *pdev);
void tmsdev_term(struct net_device *dev);
void tms380tr_wait(unsigned long time);
@@ -719,7 +718,7 @@
struct sk_buff *Skb;
unsigned char TPLIndex;
volatile unsigned char BusyFlag;/* Flag: TPL busy? */
- dma_addr_t DMABuff; /* DMA IO bus address from pci_map */
+ dma_addr_t DMABuff; /* DMA IO bus address from dma_map */
};
/* ---------------------Receive Functions-------------------------------*
@@ -1060,7 +1059,7 @@
struct sk_buff *Skb;
SKB_STAT SkbStat;
int RPLIndex;
- dma_addr_t DMABuff; /* DMA IO bus address from pci_map */
+ dma_addr_t DMABuff; /* DMA IO bus address from dma_map */
};
/* Information that need to be kept for each board. */
@@ -1091,7 +1090,7 @@
RPL *RplTail;
unsigned char LocalRxBuffers[RPL_NUM][DEFAULT_PACKET_SIZE];
- struct pci_dev *pdev;
+ struct device *pdev;
int DataRate;
unsigned char ScbInUse;
unsigned short CMDqueue;
diff --git a/drivers/net/tokenring/tmspci.c b/drivers/net/tokenring/tmspci.c
index 2e18c0a..ab47c05 100644
--- a/drivers/net/tokenring/tmspci.c
+++ b/drivers/net/tokenring/tmspci.c
@@ -100,7 +100,7 @@
unsigned int pci_irq_line;
unsigned long pci_ioaddr;
struct card_info *cardinfo = &card_info_table[ent->driver_data];
-
+
if (versionprinted++ == 0)
printk("%s", version);
@@ -143,7 +143,7 @@
printk(":%2.2x", dev->dev_addr[i]);
printk("\n");
- ret = tmsdev_init(dev, PCI_MAX_ADDRESS, pdev);
+ ret = tmsdev_init(dev, &pdev->dev);
if (ret) {
printk("%s: unable to get memory for dev->priv.\n", dev->name);
goto err_out_irq;
diff --git a/drivers/net/wan/cycx_drv.c b/drivers/net/wan/cycx_drv.c
index 6e74af6..9e56fc3 100644
--- a/drivers/net/wan/cycx_drv.c
+++ b/drivers/net/wan/cycx_drv.c
@@ -56,7 +56,7 @@
#include <linux/sched.h> /* for jiffies, HZ, etc. */
#include <linux/cycx_drv.h> /* API definitions */
#include <linux/cycx_cfm.h> /* CYCX firmware module definitions */
-#include <linux/delay.h> /* udelay */
+#include <linux/delay.h> /* udelay, msleep_interruptible */
#include <asm/io.h> /* read[wl], write[wl], ioremap, iounmap */
#define MOD_VERSION 0
@@ -74,7 +74,6 @@
static int detect_cyc2x(void __iomem *addr);
/* Miscellaneous functions */
-static void delay_cycx(int sec);
static int get_option_index(long *optlist, long optval);
static u16 checksum(u8 *buf, u32 len);
@@ -259,7 +258,7 @@
if (readw(addr + 0x10) == TEST_PATTERN)
return 1;
- delay_cycx(1);
+ msleep_interruptible(1 * 1000);
}
return 0;
@@ -316,7 +315,7 @@
/* 80186 was in hold, go */
writeb(0, addr + START_CPU);
- delay_cycx(1);
+ msleep_interruptible(1 * 1000);
}
/* Load data.bin file through boot (reset) interface. */
@@ -462,13 +461,13 @@
cycx_reset_boot(hw->dpmbase, reset_image, img_hdr->reset_size);
/* reset is waiting for boot */
writew(GEN_POWER_ON, pt_cycld);
- delay_cycx(1);
+ msleep_interruptible(1 * 1000);
for (j = 0 ; j < 3 ; j++)
if (!readw(pt_cycld))
goto reset_loaded;
else
- delay_cycx(1);
+ msleep_interruptible(1 * 1000);
}
printk(KERN_ERR "%s: reset not started.\n", modname);
@@ -495,7 +494,7 @@
/* Arthur Ganzert's tip: wait a while after the firmware loading...
seg abr 26 17:17:12 EST 1999 - acme */
- delay_cycx(7);
+ msleep_interruptible(7 * 1000);
printk(KERN_INFO "%s: firmware loaded!\n", modname);
/* enable interrupts */
@@ -547,20 +546,13 @@
static int reset_cyc2x(void __iomem *addr)
{
writeb(0, addr + RST_ENABLE);
- delay_cycx(2);
+ msleep_interruptible(2 * 1000);
writeb(0, addr + RST_DISABLE);
- delay_cycx(2);
+ msleep_interruptible(2 * 1000);
return memory_exists(addr);
}
-/* Delay */
-static void delay_cycx(int sec)
-{
- set_current_state(TASK_INTERRUPTIBLE);
- schedule_timeout(sec * HZ);
-}
-
/* Calculate 16-bit CRC using CCITT polynomial. */
static u16 checksum(u8 *buf, u32 len)
{
diff --git a/drivers/net/wireless/orinoco.c b/drivers/net/wireless/orinoco.c
index aabcdc2..9c2d07c 100644
--- a/drivers/net/wireless/orinoco.c
+++ b/drivers/net/wireless/orinoco.c
@@ -4322,36 +4322,36 @@
*/
static const iw_handler orinoco_handler[] = {
- [SIOCSIWCOMMIT-SIOCIWFIRST] (iw_handler) orinoco_ioctl_commit,
- [SIOCGIWNAME -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getname,
- [SIOCSIWFREQ -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setfreq,
- [SIOCGIWFREQ -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getfreq,
- [SIOCSIWMODE -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setmode,
- [SIOCGIWMODE -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getmode,
- [SIOCSIWSENS -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setsens,
- [SIOCGIWSENS -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getsens,
- [SIOCGIWRANGE -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getiwrange,
- [SIOCSIWSPY -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setspy,
- [SIOCGIWSPY -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getspy,
- [SIOCSIWAP -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setwap,
- [SIOCGIWAP -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getwap,
- [SIOCSIWSCAN -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setscan,
- [SIOCGIWSCAN -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getscan,
- [SIOCSIWESSID -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setessid,
- [SIOCGIWESSID -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getessid,
- [SIOCSIWNICKN -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setnick,
- [SIOCGIWNICKN -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getnick,
- [SIOCSIWRATE -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setrate,
- [SIOCGIWRATE -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getrate,
- [SIOCSIWRTS -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setrts,
- [SIOCGIWRTS -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getrts,
- [SIOCSIWFRAG -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setfrag,
- [SIOCGIWFRAG -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getfrag,
- [SIOCGIWRETRY -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getretry,
- [SIOCSIWENCODE-SIOCIWFIRST] (iw_handler) orinoco_ioctl_setiwencode,
- [SIOCGIWENCODE-SIOCIWFIRST] (iw_handler) orinoco_ioctl_getiwencode,
- [SIOCSIWPOWER -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setpower,
- [SIOCGIWPOWER -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getpower,
+ [SIOCSIWCOMMIT-SIOCIWFIRST] = (iw_handler) orinoco_ioctl_commit,
+ [SIOCGIWNAME -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getname,
+ [SIOCSIWFREQ -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setfreq,
+ [SIOCGIWFREQ -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getfreq,
+ [SIOCSIWMODE -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setmode,
+ [SIOCGIWMODE -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getmode,
+ [SIOCSIWSENS -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setsens,
+ [SIOCGIWSENS -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getsens,
+ [SIOCGIWRANGE -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getiwrange,
+ [SIOCSIWSPY -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setspy,
+ [SIOCGIWSPY -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getspy,
+ [SIOCSIWAP -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setwap,
+ [SIOCGIWAP -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getwap,
+ [SIOCSIWSCAN -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setscan,
+ [SIOCGIWSCAN -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getscan,
+ [SIOCSIWESSID -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setessid,
+ [SIOCGIWESSID -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getessid,
+ [SIOCSIWNICKN -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setnick,
+ [SIOCGIWNICKN -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getnick,
+ [SIOCSIWRATE -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setrate,
+ [SIOCGIWRATE -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getrate,
+ [SIOCSIWRTS -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setrts,
+ [SIOCGIWRTS -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getrts,
+ [SIOCSIWFRAG -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setfrag,
+ [SIOCGIWFRAG -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getfrag,
+ [SIOCGIWRETRY -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getretry,
+ [SIOCSIWENCODE-SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setiwencode,
+ [SIOCGIWENCODE-SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getiwencode,
+ [SIOCSIWPOWER -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setpower,
+ [SIOCGIWPOWER -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getpower,
};
@@ -4359,15 +4359,15 @@
Added typecasting since we no longer use iwreq_data -- Moustafa
*/
static const iw_handler orinoco_private_handler[] = {
- [0] (iw_handler) orinoco_ioctl_reset,
- [1] (iw_handler) orinoco_ioctl_reset,
- [2] (iw_handler) orinoco_ioctl_setport3,
- [3] (iw_handler) orinoco_ioctl_getport3,
- [4] (iw_handler) orinoco_ioctl_setpreamble,
- [5] (iw_handler) orinoco_ioctl_getpreamble,
- [6] (iw_handler) orinoco_ioctl_setibssport,
- [7] (iw_handler) orinoco_ioctl_getibssport,
- [9] (iw_handler) orinoco_ioctl_getrid,
+ [0] = (iw_handler) orinoco_ioctl_reset,
+ [1] = (iw_handler) orinoco_ioctl_reset,
+ [2] = (iw_handler) orinoco_ioctl_setport3,
+ [3] = (iw_handler) orinoco_ioctl_getport3,
+ [4] = (iw_handler) orinoco_ioctl_setpreamble,
+ [5] = (iw_handler) orinoco_ioctl_getpreamble,
+ [6] = (iw_handler) orinoco_ioctl_setibssport,
+ [7] = (iw_handler) orinoco_ioctl_getibssport,
+ [9] = (iw_handler) orinoco_ioctl_getrid,
};
static const struct iw_handler_def orinoco_handler_def = {
diff --git a/drivers/parport/parport_serial.c b/drivers/parport/parport_serial.c
index 00498e2..d3dad0a 100644
--- a/drivers/parport/parport_serial.c
+++ b/drivers/parport/parport_serial.c
@@ -23,13 +23,8 @@
#include <linux/pci.h>
#include <linux/parport.h>
#include <linux/parport_pc.h>
-#include <linux/serial.h>
-#include <linux/serialP.h>
-#include <linux/list.h>
#include <linux/8250_pci.h>
-#include <asm/serial.h>
-
enum parport_pc_pci_cards {
titan_110l = 0,
titan_210l,
@@ -168,182 +163,147 @@
};
MODULE_DEVICE_TABLE(pci,parport_serial_pci_tbl);
-struct pci_board_no_ids {
- int flags;
- int num_ports;
- int base_baud;
- int uart_offset;
- int reg_shift;
- int (*init_fn)(struct pci_dev *dev, struct pci_board_no_ids *board,
- int enable);
- int first_uart_offset;
-};
-
-static int __devinit siig10x_init_fn(struct pci_dev *dev, struct pci_board_no_ids *board, int enable)
-{
- return pci_siig10x_fn(dev, enable);
-}
-
-static int __devinit siig20x_init_fn(struct pci_dev *dev, struct pci_board_no_ids *board, int enable)
-{
- return pci_siig20x_fn(dev, enable);
-}
-
-static int __devinit netmos_serial_init(struct pci_dev *dev, struct pci_board_no_ids *board, int enable)
-{
- board->num_ports = dev->subsystem_device & 0xf;
- return 0;
-}
-
-static struct pci_board_no_ids pci_boards[] __devinitdata = {
- /*
- * PCI Flags, Number of Ports, Base (Maximum) Baud Rate,
- * Offset to get to next UART's registers,
- * Register shift to use for memory-mapped I/O,
- * Initialization function, first UART offset
- */
-
-// Cards not tested are marked n/t
-// If you have one of these cards and it works for you, please tell me..
-
-/* titan_110l */ { SPCI_FL_BASE1 | SPCI_FL_BASE_TABLE, 1, 921600 },
-/* titan_210l */ { SPCI_FL_BASE1 | SPCI_FL_BASE_TABLE, 2, 921600 },
-/* netmos_9xx5_combo */ { SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 1, 115200, 0, 0, netmos_serial_init },
-/* netmos_9855 */ { SPCI_FL_BASE2 | SPCI_FL_BASE_TABLE, 1, 115200, 0, 0, netmos_serial_init },
-/* avlab_1s1p (n/t) */ { SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 1, 115200 },
-/* avlab_1s1p_650 (nt)*/{ SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 1, 115200 },
-/* avlab_1s1p_850 (nt)*/{ SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 1, 115200 },
-/* avlab_1s2p (n/t) */ { SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 1, 115200 },
-/* avlab_1s2p_650 (nt)*/{ SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 1, 115200 },
-/* avlab_1s2p_850 (nt)*/{ SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 1, 115200 },
-/* avlab_2s1p (n/t) */ { SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 2, 115200 },
-/* avlab_2s1p_650 (nt)*/{ SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 2, 115200 },
-/* avlab_2s1p_850 (nt)*/{ SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 2, 115200 },
-/* siig_1s1p_10x */ { SPCI_FL_BASE2, 1, 460800, 0, 0, siig10x_init_fn },
-/* siig_2s1p_10x */ { SPCI_FL_BASE2, 1, 921600, 0, 0, siig10x_init_fn },
-/* siig_2p1s_20x */ { SPCI_FL_BASE0, 1, 921600, 0, 0, siig20x_init_fn },
-/* siig_1s1p_20x */ { SPCI_FL_BASE0, 1, 921600, 0, 0, siig20x_init_fn },
-/* siig_2s1p_20x */ { SPCI_FL_BASE0, 1, 921600, 0, 0, siig20x_init_fn },
+/*
+ * This table describes the serial "geometry" of these boards. Any
+ * quirks for these can be found in drivers/serial/8250_pci.c
+ *
+ * Cards not tested are marked n/t
+ * If you have one of these cards and it works for you, please tell me..
+ */
+static struct pciserial_board pci_parport_serial_boards[] __devinitdata = {
+ [titan_110l] = {
+ .flags = FL_BASE1 | FL_BASE_BARS,
+ .num_ports = 1,
+ .base_baud = 921600,
+ .uart_offset = 8,
+ },
+ [titan_210l] = {
+ .flags = FL_BASE1 | FL_BASE_BARS,
+ .num_ports = 2,
+ .base_baud = 921600,
+ .uart_offset = 8,
+ },
+ [netmos_9xx5_combo] = {
+ .flags = FL_BASE0 | FL_BASE_BARS,
+ .num_ports = 1,
+ .base_baud = 115200,
+ .uart_offset = 8,
+ },
+ [netmos_9855] = {
+ .flags = FL_BASE2 | FL_BASE_BARS,
+ .num_ports = 1,
+ .base_baud = 115200,
+ .uart_offset = 8,
+ },
+ [avlab_1s1p] = { /* n/t */
+ .flags = FL_BASE0 | FL_BASE_BARS,
+ .num_ports = 1,
+ .base_baud = 115200,
+ .uart_offset = 8,
+ },
+ [avlab_1s1p_650] = { /* nt */
+ .flags = FL_BASE0 | FL_BASE_BARS,
+ .num_ports = 1,
+ .base_baud = 115200,
+ .uart_offset = 8,
+ },
+ [avlab_1s1p_850] = { /* nt */
+ .flags = FL_BASE0 | FL_BASE_BARS,
+ .num_ports = 1,
+ .base_baud = 115200,
+ .uart_offset = 8,
+ },
+ [avlab_1s2p] = { /* n/t */
+ .flags = FL_BASE0 | FL_BASE_BARS,
+ .num_ports = 1,
+ .base_baud = 115200,
+ .uart_offset = 8,
+ },
+ [avlab_1s2p_650] = { /* nt */
+ .flags = FL_BASE0 | FL_BASE_BARS,
+ .num_ports = 1,
+ .base_baud = 115200,
+ .uart_offset = 8,
+ },
+ [avlab_1s2p_850] = { /* nt */
+ .flags = FL_BASE0 | FL_BASE_BARS,
+ .num_ports = 1,
+ .base_baud = 115200,
+ .uart_offset = 8,
+ },
+ [avlab_2s1p] = { /* n/t */
+ .flags = FL_BASE0 | FL_BASE_BARS,
+ .num_ports = 2,
+ .base_baud = 115200,
+ .uart_offset = 8,
+ },
+ [avlab_2s1p_650] = { /* nt */
+ .flags = FL_BASE0 | FL_BASE_BARS,
+ .num_ports = 2,
+ .base_baud = 115200,
+ .uart_offset = 8,
+ },
+ [avlab_2s1p_850] = { /* nt */
+ .flags = FL_BASE0 | FL_BASE_BARS,
+ .num_ports = 2,
+ .base_baud = 115200,
+ .uart_offset = 8,
+ },
+ [siig_1s1p_10x] = {
+ .flags = FL_BASE2,
+ .num_ports = 1,
+ .base_baud = 460800,
+ .uart_offset = 8,
+ },
+ [siig_2s1p_10x] = {
+ .flags = FL_BASE2,
+ .num_ports = 1,
+ .base_baud = 921600,
+ .uart_offset = 8,
+ },
+ [siig_2p1s_20x] = {
+ .flags = FL_BASE0,
+ .num_ports = 1,
+ .base_baud = 921600,
+ .uart_offset = 8,
+ },
+ [siig_1s1p_20x] = {
+ .flags = FL_BASE0,
+ .num_ports = 1,
+ .base_baud = 921600,
+ .uart_offset = 8,
+ },
+ [siig_2s1p_20x] = {
+ .flags = FL_BASE0,
+ .num_ports = 1,
+ .base_baud = 921600,
+ .uart_offset = 8,
+ },
};
struct parport_serial_private {
- int num_ser;
- int line[20];
- struct pci_board_no_ids ser;
+ struct serial_private *serial;
int num_par;
struct parport *port[PARPORT_MAX];
struct parport_pc_pci par;
};
-static int __devinit get_pci_port (struct pci_dev *dev,
- struct pci_board_no_ids *board,
- struct serial_struct *req,
- int idx)
-{
- unsigned long port;
- int base_idx;
- int max_port;
- int offset;
-
- base_idx = SPCI_FL_GET_BASE(board->flags);
- if (board->flags & SPCI_FL_BASE_TABLE)
- base_idx += idx;
-
- if (board->flags & SPCI_FL_REGION_SZ_CAP) {
- max_port = pci_resource_len(dev, base_idx) / 8;
- if (idx >= max_port)
- return 1;
- }
-
- offset = board->first_uart_offset;
-
- /* Timedia/SUNIX uses a mixture of BARs and offsets */
- /* Ugh, this is ugly as all hell --- TYT */
- if(dev->vendor == PCI_VENDOR_ID_TIMEDIA ) /* 0x1409 */
- switch(idx) {
- case 0: base_idx=0;
- break;
- case 1: base_idx=0; offset=8;
- break;
- case 2: base_idx=1;
- break;
- case 3: base_idx=1; offset=8;
- break;
- case 4: /* BAR 2*/
- case 5: /* BAR 3 */
- case 6: /* BAR 4*/
- case 7: base_idx=idx-2; /* BAR 5*/
- }
-
- port = pci_resource_start(dev, base_idx) + offset;
-
- if ((board->flags & SPCI_FL_BASE_TABLE) == 0)
- port += idx * (board->uart_offset ? board->uart_offset : 8);
-
- if (pci_resource_flags (dev, base_idx) & IORESOURCE_IO) {
- int high_bits_offset = ((sizeof(long)-sizeof(int))*8);
- req->port = port;
- if (high_bits_offset)
- req->port_high = port >> high_bits_offset;
- else
- req->port_high = 0;
- return 0;
- }
- req->io_type = SERIAL_IO_MEM;
- req->iomem_base = ioremap(port, board->uart_offset);
- req->iomem_reg_shift = board->reg_shift;
- req->port = 0;
- return req->iomem_base ? 0 : 1;
-}
-
/* Register the serial port(s) of a PCI card. */
static int __devinit serial_register (struct pci_dev *dev,
const struct pci_device_id *id)
{
- struct pci_board_no_ids *board;
struct parport_serial_private *priv = pci_get_drvdata (dev);
- struct serial_struct serial_req;
- int base_baud;
- int k;
- int success = 0;
+ struct pciserial_board *board;
+ struct serial_private *serial;
- priv->ser = pci_boards[id->driver_data];
- board = &priv->ser;
- if (board->init_fn && ((board->init_fn) (dev, board, 1) != 0))
- return 1;
+ board = &pci_parport_serial_boards[id->driver_data];
+ serial = pciserial_init_ports(dev, board);
- base_baud = board->base_baud;
- if (!base_baud)
- base_baud = BASE_BAUD;
- memset (&serial_req, 0, sizeof (serial_req));
+ if (IS_ERR(serial))
+ return PTR_ERR(serial);
- for (k = 0; k < board->num_ports; k++) {
- int line;
-
- if (priv->num_ser == ARRAY_SIZE (priv->line)) {
- printk (KERN_WARNING
- "parport_serial: %s: only %u serial lines "
- "supported (%d reported)\n", pci_name (dev),
- ARRAY_SIZE (priv->line), board->num_ports);
- break;
- }
-
- serial_req.irq = dev->irq;
- if (get_pci_port (dev, board, &serial_req, k))
- break;
- serial_req.flags = ASYNC_SKIP_TEST | ASYNC_AUTOPROBE;
- serial_req.baud_base = base_baud;
- line = register_serial (&serial_req);
- if (line < 0) {
- printk (KERN_DEBUG
- "parport_serial: register_serial failed\n");
- continue;
- }
- priv->line[priv->num_ser++] = line;
- success = 1;
- }
-
- return success ? 0 : 1;
+ priv->serial = serial;
+ return 0;
}
/* Register the parallel port(s) of a PCI card. */
@@ -411,7 +371,7 @@
priv = kmalloc (sizeof *priv, GFP_KERNEL);
if (!priv)
return -ENOMEM;
- priv->num_ser = priv->num_par = 0;
+ memset(priv, 0, sizeof(struct parport_serial_private));
pci_set_drvdata (dev, priv);
err = pci_enable_device (dev);
@@ -444,15 +404,12 @@
struct parport_serial_private *priv = pci_get_drvdata (dev);
int i;
- // Serial ports
- for (i = 0; i < priv->num_ser; i++) {
- unregister_serial (priv->line[i]);
+ pci_set_drvdata(dev, NULL);
- if (priv->ser.init_fn)
- (priv->ser.init_fn) (dev, &priv->ser, 0);
- }
- pci_set_drvdata (dev, NULL);
-
+ // Serial ports
+ if (priv->serial)
+ pciserial_remove_ports(priv->serial);
+
// Parallel ports
for (i = 0; i < priv->num_par; i++)
parport_pc_unregister_port (priv->port[i]);
@@ -461,11 +418,47 @@
return;
}
+static int parport_serial_pci_suspend(struct pci_dev *dev, pm_message_t state)
+{
+ struct parport_serial_private *priv = pci_get_drvdata(dev);
+
+ if (priv->serial)
+ pciserial_suspend_ports(priv->serial);
+
+ /* FIXME: What about parport? */
+
+ pci_save_state(dev);
+ pci_set_power_state(dev, pci_choose_state(dev, state));
+ return 0;
+}
+
+static int parport_serial_pci_resume(struct pci_dev *dev)
+{
+ struct parport_serial_private *priv = pci_get_drvdata(dev);
+
+ pci_set_power_state(dev, PCI_D0);
+ pci_restore_state(dev);
+
+ /*
+ * The device may have been disabled. Re-enable it.
+ */
+ pci_enable_device(dev);
+
+ if (priv->serial)
+ pciserial_resume_ports(priv->serial);
+
+ /* FIXME: What about parport? */
+
+ return 0;
+}
+
static struct pci_driver parport_serial_pci_driver = {
.name = "parport_serial",
.id_table = parport_serial_pci_tbl,
.probe = parport_serial_pci_probe,
.remove = __devexit_p(parport_serial_pci_remove),
+ .suspend = parport_serial_pci_suspend,
+ .resume = parport_serial_pci_resume,
};
diff --git a/drivers/s390/scsi/zfcp_aux.c b/drivers/s390/scsi/zfcp_aux.c
index e17b4d5..bfe3ba7 100644
--- a/drivers/s390/scsi/zfcp_aux.c
+++ b/drivers/s390/scsi/zfcp_aux.c
@@ -1299,13 +1299,10 @@
zfcp_port_enqueue(struct zfcp_adapter *adapter, wwn_t wwpn, u32 status,
u32 d_id)
{
- struct zfcp_port *port, *tmp_port;
+ struct zfcp_port *port;
int check_wwpn;
- scsi_id_t scsi_id;
- int found;
check_wwpn = !(status & ZFCP_STATUS_PORT_NO_WWPN);
-
/*
* check that there is no port with this WWPN already in list
*/
@@ -1368,7 +1365,7 @@
} else {
snprintf(port->sysfs_device.bus_id,
BUS_ID_SIZE, "0x%016llx", wwpn);
- port->sysfs_device.parent = &adapter->ccw_device->dev;
+ port->sysfs_device.parent = &adapter->ccw_device->dev;
}
port->sysfs_device.release = zfcp_sysfs_port_release;
dev_set_drvdata(&port->sysfs_device, port);
@@ -1388,24 +1385,8 @@
zfcp_port_get(port);
- scsi_id = 1;
- found = 0;
write_lock_irq(&zfcp_data.config_lock);
- list_for_each_entry(tmp_port, &adapter->port_list_head, list) {
- if (atomic_test_mask(ZFCP_STATUS_PORT_NO_SCSI_ID,
- &tmp_port->status))
- continue;
- if (tmp_port->scsi_id != scsi_id) {
- found = 1;
- break;
- }
- scsi_id++;
- }
- port->scsi_id = scsi_id;
- if (found)
- list_add_tail(&port->list, &tmp_port->list);
- else
- list_add_tail(&port->list, &adapter->port_list_head);
+ list_add_tail(&port->list, &adapter->port_list_head);
atomic_clear_mask(ZFCP_STATUS_COMMON_REMOVE, &port->status);
atomic_set_mask(ZFCP_STATUS_COMMON_RUNNING, &port->status);
if (d_id == ZFCP_DID_DIRECTORY_SERVICE)
@@ -1427,6 +1408,9 @@
list_del(&port->list);
port->adapter->ports--;
write_unlock_irq(&zfcp_data.config_lock);
+ if (port->rport)
+ fc_remote_port_delete(port->rport);
+ port->rport = NULL;
zfcp_adapter_put(port->adapter);
zfcp_sysfs_port_remove_files(&port->sysfs_device,
atomic_read(&port->status));
diff --git a/drivers/s390/scsi/zfcp_ccw.c b/drivers/s390/scsi/zfcp_ccw.c
index 0fc4638..b30abab 100644
--- a/drivers/s390/scsi/zfcp_ccw.c
+++ b/drivers/s390/scsi/zfcp_ccw.c
@@ -202,9 +202,19 @@
zfcp_ccw_set_offline(struct ccw_device *ccw_device)
{
struct zfcp_adapter *adapter;
+ struct zfcp_port *port;
+ struct fc_rport *rport;
down(&zfcp_data.config_sema);
adapter = dev_get_drvdata(&ccw_device->dev);
+ /* might be racy, but we cannot take config_lock due to the fact that
+ fc_remote_port_delete might sleep */
+ list_for_each_entry(port, &adapter->port_list_head, list)
+ if (port->rport) {
+ rport = port->rport;
+ port->rport = NULL;
+ fc_remote_port_delete(rport);
+ }
zfcp_erp_adapter_shutdown(adapter, 0);
zfcp_erp_wait(adapter);
zfcp_adapter_scsi_unregister(adapter);
diff --git a/drivers/s390/scsi/zfcp_def.h b/drivers/s390/scsi/zfcp_def.h
index 4103b5b..455e902 100644
--- a/drivers/s390/scsi/zfcp_def.h
+++ b/drivers/s390/scsi/zfcp_def.h
@@ -906,6 +906,7 @@
*/
struct zfcp_port {
struct device sysfs_device; /* sysfs device */
+ struct fc_rport *rport; /* rport of fc transport class */
struct list_head list; /* list of remote ports */
atomic_t refcount; /* reference count */
wait_queue_head_t remove_wq; /* can be used to wait for
@@ -916,7 +917,6 @@
list */
u32 units; /* # of logical units in list */
atomic_t status; /* status of this remote port */
- scsi_id_t scsi_id; /* own SCSI ID */
wwn_t wwnn; /* WWNN if known */
wwn_t wwpn; /* WWPN */
fc_id_t d_id; /* D_ID */
diff --git a/drivers/s390/scsi/zfcp_erp.c b/drivers/s390/scsi/zfcp_erp.c
index 0cf31f7..cb4f612 100644
--- a/drivers/s390/scsi/zfcp_erp.c
+++ b/drivers/s390/scsi/zfcp_erp.c
@@ -3360,13 +3360,32 @@
if ((result == ZFCP_ERP_SUCCEEDED)
&& (!atomic_test_mask(ZFCP_STATUS_UNIT_TEMPORARY,
&unit->status))
- && (!unit->device))
- scsi_add_device(unit->port->adapter->scsi_host, 0,
- unit->port->scsi_id, unit->scsi_lun);
+ && !unit->device
+ && port->rport)
+ scsi_add_device(port->adapter->scsi_host, 0,
+ port->rport->scsi_target_id,
+ unit->scsi_lun);
zfcp_unit_put(unit);
break;
case ZFCP_ERP_ACTION_REOPEN_PORT_FORCED:
case ZFCP_ERP_ACTION_REOPEN_PORT:
+ if ((result == ZFCP_ERP_SUCCEEDED)
+ && !atomic_test_mask(ZFCP_STATUS_PORT_NO_WWPN,
+ &port->status)
+ && !port->rport) {
+ struct fc_rport_identifiers ids;
+ ids.node_name = port->wwnn;
+ ids.port_name = port->wwpn;
+ ids.port_id = port->d_id;
+ ids.roles = FC_RPORT_ROLE_FCP_TARGET;
+ port->rport =
+ fc_remote_port_add(adapter->scsi_host, 0, &ids);
+ if (!port->rport)
+ ZFCP_LOG_NORMAL("failed registration of rport"
+ "(adapter %s, wwpn=0x%016Lx)\n",
+ zfcp_get_busid_by_port(port),
+ port->wwpn);
+ }
zfcp_port_put(port);
break;
case ZFCP_ERP_ACTION_REOPEN_ADAPTER:
diff --git a/drivers/s390/scsi/zfcp_ext.h b/drivers/s390/scsi/zfcp_ext.h
index 42df7e5..cd98a2d 100644
--- a/drivers/s390/scsi/zfcp_ext.h
+++ b/drivers/s390/scsi/zfcp_ext.h
@@ -143,6 +143,8 @@
struct scsi_cmnd *, struct timer_list *);
extern int zfcp_scsi_command_sync(struct zfcp_unit *, struct scsi_cmnd *,
struct timer_list *);
+extern void zfcp_set_fc_host_attrs(struct zfcp_adapter *);
+extern void zfcp_set_fc_rport_attrs(struct zfcp_port *);
extern struct scsi_transport_template *zfcp_transport_template;
extern struct fc_function_template zfcp_transport_functions;
diff --git a/drivers/s390/scsi/zfcp_fsf.c b/drivers/s390/scsi/zfcp_fsf.c
index 0d9f20e..c007b64 100644
--- a/drivers/s390/scsi/zfcp_fsf.c
+++ b/drivers/s390/scsi/zfcp_fsf.c
@@ -2062,6 +2062,7 @@
zfcp_erp_adapter_shutdown(adapter, 0);
return -EIO;
}
+ zfcp_set_fc_host_attrs(adapter);
return 0;
}
diff --git a/drivers/s390/scsi/zfcp_scsi.c b/drivers/s390/scsi/zfcp_scsi.c
index b61d309..31a7606 100644
--- a/drivers/s390/scsi/zfcp_scsi.c
+++ b/drivers/s390/scsi/zfcp_scsi.c
@@ -389,7 +389,7 @@
struct zfcp_unit *unit, *retval = NULL;
list_for_each_entry(port, &adapter->port_list_head, list) {
- if (id != port->scsi_id)
+ if (!port->rport || (id != port->rport->scsi_target_id))
continue;
list_for_each_entry(unit, &port->unit_list_head, list) {
if (lun == unit->scsi_lun) {
@@ -408,7 +408,7 @@
struct zfcp_port *port;
list_for_each_entry(port, &adapter->port_list_head, list) {
- if (id == port->scsi_id)
+ if (port->rport && (id == port->rport->scsi_target_id))
return port;
}
return (struct zfcp_port *) NULL;
@@ -634,7 +634,6 @@
{
int retval;
struct zfcp_unit *unit = (struct zfcp_unit *) scpnt->device->hostdata;
- struct Scsi_Host *scsi_host = scpnt->device->host;
if (!unit) {
ZFCP_LOG_NORMAL("bug: Tried reset for nonexistent unit\n");
@@ -729,7 +728,6 @@
{
int retval = 0;
struct zfcp_unit *unit;
- struct Scsi_Host *scsi_host = scpnt->device->host;
unit = (struct zfcp_unit *) scpnt->device->hostdata;
ZFCP_LOG_NORMAL("bus reset because of problems with "
@@ -753,7 +751,6 @@
{
int retval = 0;
struct zfcp_unit *unit;
- struct Scsi_Host *scsi_host = scpnt->device->host;
unit = (struct zfcp_unit *) scpnt->device->hostdata;
ZFCP_LOG_NORMAL("host reset because of problems with "
@@ -833,6 +830,7 @@
shost = adapter->scsi_host;
if (!shost)
return;
+ fc_remove_host(shost);
scsi_remove_host(shost);
scsi_host_put(shost);
adapter->scsi_host = NULL;
@@ -906,6 +904,18 @@
read_unlock_irqrestore(&zfcp_data.config_lock, flags);
}
+void
+zfcp_set_fc_host_attrs(struct zfcp_adapter *adapter)
+{
+ struct Scsi_Host *shost = adapter->scsi_host;
+
+ fc_host_node_name(shost) = adapter->wwnn;
+ fc_host_port_name(shost) = adapter->wwpn;
+ strncpy(fc_host_serial_number(shost), adapter->serial_number,
+ min(FC_SERIAL_NUMBER_SIZE, 32));
+ fc_host_supported_classes(shost) = FC_COS_CLASS2 | FC_COS_CLASS3;
+}
+
struct fc_function_template zfcp_transport_functions = {
.get_starget_port_id = zfcp_get_port_id,
.get_starget_port_name = zfcp_get_port_name,
@@ -913,6 +923,11 @@
.show_starget_port_id = 1,
.show_starget_port_name = 1,
.show_starget_node_name = 1,
+ .show_rport_supported_classes = 1,
+ .show_host_node_name = 1,
+ .show_host_port_name = 1,
+ .show_host_supported_classes = 1,
+ .show_host_serial_number = 1,
};
/**
diff --git a/drivers/s390/scsi/zfcp_sysfs_port.c b/drivers/s390/scsi/zfcp_sysfs_port.c
index 7a84c7d..c55e82d 100644
--- a/drivers/s390/scsi/zfcp_sysfs_port.c
+++ b/drivers/s390/scsi/zfcp_sysfs_port.c
@@ -67,7 +67,6 @@
ZFCP_DEFINE_PORT_ATTR(status, "0x%08x\n", atomic_read(&port->status));
ZFCP_DEFINE_PORT_ATTR(wwnn, "0x%016llx\n", port->wwnn);
ZFCP_DEFINE_PORT_ATTR(d_id, "0x%06x\n", port->d_id);
-ZFCP_DEFINE_PORT_ATTR(scsi_id, "0x%x\n", port->scsi_id);
ZFCP_DEFINE_PORT_ATTR(in_recovery, "%d\n", atomic_test_mask
(ZFCP_STATUS_COMMON_ERP_INUSE, &port->status));
ZFCP_DEFINE_PORT_ATTR(access_denied, "%d\n", atomic_test_mask
@@ -263,7 +262,6 @@
static struct attribute *zfcp_port_no_ns_attrs[] = {
&dev_attr_unit_add.attr,
&dev_attr_unit_remove.attr,
- &dev_attr_scsi_id.attr,
NULL
};
diff --git a/drivers/scsi/ahci.c b/drivers/scsi/ahci.c
index e3b9692..841f4e2 100644
--- a/drivers/scsi/ahci.c
+++ b/drivers/scsi/ahci.c
@@ -269,6 +269,8 @@
board_ahci }, /* ESB2 */
{ PCI_VENDOR_ID_INTEL, 0x2683, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
board_ahci }, /* ESB2 */
+ { PCI_VENDOR_ID_INTEL, 0x27c6, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ board_ahci }, /* ICH7-M DH */
{ } /* terminate list */
};
@@ -584,12 +586,16 @@
static void ahci_eng_timeout(struct ata_port *ap)
{
- void *mmio = ap->host_set->mmio_base;
+ struct ata_host_set *host_set = ap->host_set;
+ void *mmio = host_set->mmio_base;
void *port_mmio = ahci_port_base(mmio, ap->port_no);
struct ata_queued_cmd *qc;
+ unsigned long flags;
DPRINTK("ENTER\n");
+ spin_lock_irqsave(&host_set->lock, flags);
+
ahci_intr_error(ap, readl(port_mmio + PORT_IRQ_STAT));
qc = ata_qc_from_tag(ap, ap->active_tag);
@@ -607,6 +613,7 @@
ata_qc_complete(qc, ATA_ERR);
}
+ spin_unlock_irqrestore(&host_set->lock, flags);
}
static inline int ahci_host_intr(struct ata_port *ap, struct ata_queued_cmd *qc)
@@ -696,9 +703,6 @@
struct ata_port *ap = qc->ap;
void *port_mmio = (void *) ap->ioaddr.cmd_addr;
- writel(1, port_mmio + PORT_SCR_ACT);
- readl(port_mmio + PORT_SCR_ACT); /* flush */
-
writel(1, port_mmio + PORT_CMD_ISSUE);
readl(port_mmio + PORT_CMD_ISSUE); /* flush */
diff --git a/drivers/scsi/ata_piix.c b/drivers/scsi/ata_piix.c
index d96ebf9..0369561 100644
--- a/drivers/scsi/ata_piix.c
+++ b/drivers/scsi/ata_piix.c
@@ -629,13 +629,13 @@
port_info[1] = NULL;
if (port_info[0]->host_flags & PIIX_FLAG_AHCI) {
- u8 tmp;
- pci_read_config_byte(pdev, PIIX_SCC, &tmp);
- if (tmp == PIIX_AHCI_DEVICE) {
- int rc = piix_disable_ahci(pdev);
- if (rc)
- return rc;
- }
+ u8 tmp;
+ pci_read_config_byte(pdev, PIIX_SCC, &tmp);
+ if (tmp == PIIX_AHCI_DEVICE) {
+ int rc = piix_disable_ahci(pdev);
+ if (rc)
+ return rc;
+ }
}
if (port_info[0]->host_flags & PIIX_FLAG_COMBINED) {
diff --git a/drivers/scsi/libata-core.c b/drivers/scsi/libata-core.c
index f4e7dcb..f15a07f 100644
--- a/drivers/scsi/libata-core.c
+++ b/drivers/scsi/libata-core.c
@@ -1304,12 +1304,12 @@
/**
* ata_dev_config - Run device specific handlers and check for
* SATA->PATA bridges
- * @ap: Bus
+ * @ap: Bus
* @i: Device
*
* LOCKING:
*/
-
+
void ata_dev_config(struct ata_port *ap, unsigned int i)
{
/* limit bridge transfers to udma5, 200 sectors */
@@ -2377,6 +2377,27 @@
}
/**
+ * ata_poll_qc_complete - turn irq back on and finish qc
+ * @qc: Command to complete
+ * @drv_stat: ATA status register content
+ *
+ * LOCKING:
+ * None. (grabs host lock)
+ */
+
+void ata_poll_qc_complete(struct ata_queued_cmd *qc, u8 drv_stat)
+{
+ struct ata_port *ap = qc->ap;
+ unsigned long flags;
+
+ spin_lock_irqsave(&ap->host_set->lock, flags);
+ ap->flags &= ~ATA_FLAG_NOINTR;
+ ata_irq_on(ap);
+ ata_qc_complete(qc, drv_stat);
+ spin_unlock_irqrestore(&ap->host_set->lock, flags);
+}
+
+/**
* ata_pio_poll -
* @ap:
*
@@ -2438,11 +2459,10 @@
u8 drv_stat;
/*
- * This is purely hueristic. This is a fast path.
- * Sometimes when we enter, BSY will be cleared in
- * a chk-status or two. If not, the drive is probably seeking
- * or something. Snooze for a couple msecs, then
- * chk-status again. If still busy, fall back to
+ * This is purely heuristic. This is a fast path. Sometimes when
+ * we enter, BSY will be cleared in a chk-status or two. If not,
+ * the drive is probably seeking or something. Snooze for a couple
+ * msecs, then chk-status again. If still busy, fall back to
* PIO_ST_POLL state.
*/
drv_stat = ata_busy_wait(ap, ATA_BUSY | ATA_DRQ, 10);
@@ -2467,9 +2487,7 @@
ap->pio_task_state = PIO_ST_IDLE;
- ata_irq_on(ap);
-
- ata_qc_complete(qc, drv_stat);
+ ata_poll_qc_complete(qc, drv_stat);
}
@@ -2494,6 +2512,20 @@
#endif /* __BIG_ENDIAN */
}
+/**
+ * ata_mmio_data_xfer - Transfer data by MMIO
+ * @ap: port to read/write
+ * @buf: data buffer
+ * @buflen: buffer length
+ * @do_write: read/write
+ *
+ * Transfer data from/to the device data register by MMIO.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ *
+ */
+
static void ata_mmio_data_xfer(struct ata_port *ap, unsigned char *buf,
unsigned int buflen, int write_data)
{
@@ -2502,6 +2534,7 @@
u16 *buf16 = (u16 *) buf;
void __iomem *mmio = (void __iomem *)ap->ioaddr.data_addr;
+ /* Transfer multiple of 2 bytes */
if (write_data) {
for (i = 0; i < words; i++)
writew(le16_to_cpu(buf16[i]), mmio);
@@ -2509,19 +2542,76 @@
for (i = 0; i < words; i++)
buf16[i] = cpu_to_le16(readw(mmio));
}
+
+ /* Transfer trailing 1 byte, if any. */
+ if (unlikely(buflen & 0x01)) {
+ u16 align_buf[1] = { 0 };
+ unsigned char *trailing_buf = buf + buflen - 1;
+
+ if (write_data) {
+ memcpy(align_buf, trailing_buf, 1);
+ writew(le16_to_cpu(align_buf[0]), mmio);
+ } else {
+ align_buf[0] = cpu_to_le16(readw(mmio));
+ memcpy(trailing_buf, align_buf, 1);
+ }
+ }
}
+/**
+ * ata_pio_data_xfer - Transfer data by PIO
+ * @ap: port to read/write
+ * @buf: data buffer
+ * @buflen: buffer length
+ * @do_write: read/write
+ *
+ * Transfer data from/to the device data register by PIO.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ *
+ */
+
static void ata_pio_data_xfer(struct ata_port *ap, unsigned char *buf,
unsigned int buflen, int write_data)
{
- unsigned int dwords = buflen >> 1;
+ unsigned int words = buflen >> 1;
+ /* Transfer multiple of 2 bytes */
if (write_data)
- outsw(ap->ioaddr.data_addr, buf, dwords);
+ outsw(ap->ioaddr.data_addr, buf, words);
else
- insw(ap->ioaddr.data_addr, buf, dwords);
+ insw(ap->ioaddr.data_addr, buf, words);
+
+ /* Transfer trailing 1 byte, if any. */
+ if (unlikely(buflen & 0x01)) {
+ u16 align_buf[1] = { 0 };
+ unsigned char *trailing_buf = buf + buflen - 1;
+
+ if (write_data) {
+ memcpy(align_buf, trailing_buf, 1);
+ outw(le16_to_cpu(align_buf[0]), ap->ioaddr.data_addr);
+ } else {
+ align_buf[0] = cpu_to_le16(inw(ap->ioaddr.data_addr));
+ memcpy(trailing_buf, align_buf, 1);
+ }
+ }
}
+/**
+ * ata_data_xfer - Transfer data from/to the data register.
+ * @ap: port to read/write
+ * @buf: data buffer
+ * @buflen: buffer length
+ * @do_write: read/write
+ *
+ * Transfer data from/to the device data register.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ *
+ */
+
static void ata_data_xfer(struct ata_port *ap, unsigned char *buf,
unsigned int buflen, int do_write)
{
@@ -2531,6 +2621,16 @@
ata_pio_data_xfer(ap, buf, buflen, do_write);
}
+/**
+ * ata_pio_sector - Transfer ATA_SECT_SIZE (512 bytes) of data.
+ * @qc: Command on going
+ *
+ * Transfer ATA_SECT_SIZE of data from/to the ATA device.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+
static void ata_pio_sector(struct ata_queued_cmd *qc)
{
int do_write = (qc->tf.flags & ATA_TFLAG_WRITE);
@@ -2569,6 +2669,18 @@
kunmap(page);
}
+/**
+ * __atapi_pio_bytes - Transfer data from/to the ATAPI device.
+ * @qc: Command on going
+ * @bytes: number of bytes
+ *
+ * Transfer Transfer data from/to the ATAPI device.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ *
+ */
+
static void __atapi_pio_bytes(struct ata_queued_cmd *qc, unsigned int bytes)
{
int do_write = (qc->tf.flags & ATA_TFLAG_WRITE);
@@ -2578,10 +2690,33 @@
unsigned char *buf;
unsigned int offset, count;
- if (qc->curbytes == qc->nbytes - bytes)
+ if (qc->curbytes + bytes >= qc->nbytes)
ap->pio_task_state = PIO_ST_LAST;
next_sg:
+ if (unlikely(qc->cursg >= qc->n_elem)) {
+ /*
+ * The end of qc->sg is reached and the device expects
+ * more data to transfer. In order not to overrun qc->sg
+ * and fulfill length specified in the byte count register,
+ * - for read case, discard trailing data from the device
+ * - for write case, padding zero data to the device
+ */
+ u16 pad_buf[1] = { 0 };
+ unsigned int words = bytes >> 1;
+ unsigned int i;
+
+ if (words) /* warning if bytes > 1 */
+ printk(KERN_WARNING "ata%u: %u bytes trailing data\n",
+ ap->id, bytes);
+
+ for (i = 0; i < words; i++)
+ ata_data_xfer(ap, (unsigned char*)pad_buf, 2, do_write);
+
+ ap->pio_task_state = PIO_ST_LAST;
+ return;
+ }
+
sg = &qc->sg[qc->cursg];
page = sg->page;
@@ -2615,11 +2750,21 @@
kunmap(page);
- if (bytes) {
+ if (bytes)
goto next_sg;
- }
}
+/**
+ * atapi_pio_bytes - Transfer data from/to the ATAPI device.
+ * @qc: Command on going
+ *
+ * Transfer Transfer data from/to the ATAPI device.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ *
+ */
+
static void atapi_pio_bytes(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
@@ -2692,9 +2837,7 @@
if ((status & ATA_DRQ) == 0) {
ap->pio_task_state = PIO_ST_IDLE;
- ata_irq_on(ap);
-
- ata_qc_complete(qc, status);
+ ata_poll_qc_complete(qc, status);
return;
}
@@ -2724,9 +2867,7 @@
ap->pio_task_state = PIO_ST_IDLE;
- ata_irq_on(ap);
-
- ata_qc_complete(qc, drv_stat | ATA_ERR);
+ ata_poll_qc_complete(qc, drv_stat | ATA_ERR);
}
static void ata_pio_task(void *_data)
@@ -2832,8 +2973,10 @@
static void ata_qc_timeout(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
+ struct ata_host_set *host_set = ap->host_set;
struct ata_device *dev = qc->dev;
u8 host_stat = 0, drv_stat;
+ unsigned long flags;
DPRINTK("ENTER\n");
@@ -2844,7 +2987,9 @@
if (!(cmd->eh_eflags & SCSI_EH_CANCEL_CMD)) {
/* finish completing original command */
+ spin_lock_irqsave(&host_set->lock, flags);
__ata_qc_complete(qc);
+ spin_unlock_irqrestore(&host_set->lock, flags);
atapi_request_sense(ap, dev, cmd);
@@ -2855,6 +3000,8 @@
}
}
+ spin_lock_irqsave(&host_set->lock, flags);
+
/* hack alert! We cannot use the supplied completion
* function from inside the ->eh_strategy_handler() thread.
* libata is the only user of ->eh_strategy_handler() in
@@ -2870,7 +3017,7 @@
host_stat = ap->ops->bmdma_status(ap);
/* before we do anything else, clear DMA-Start bit */
- ap->ops->bmdma_stop(ap);
+ ap->ops->bmdma_stop(qc);
/* fall through */
@@ -2888,6 +3035,9 @@
ata_qc_complete(qc, drv_stat);
break;
}
+
+ spin_unlock_irqrestore(&host_set->lock, flags);
+
out:
DPRINTK("EXIT\n");
}
@@ -3061,9 +3211,14 @@
if (likely(qc->flags & ATA_QCFLAG_DMAMAP))
ata_sg_clean(qc);
+ /* atapi: mark qc as inactive to prevent the interrupt handler
+ * from completing the command twice later, before the error handler
+ * is called. (when rc != 0 and atapi request sense is needed)
+ */
+ qc->flags &= ~ATA_QCFLAG_ACTIVE;
+
/* call completion callback */
rc = qc->complete_fn(qc, drv_stat);
- qc->flags &= ~ATA_QCFLAG_ACTIVE;
/* if callback indicates not to complete command (non-zero),
* return immediately
@@ -3193,11 +3348,13 @@
break;
case ATA_PROT_ATAPI_NODATA:
+ ap->flags |= ATA_FLAG_NOINTR;
ata_tf_to_host_nolock(ap, &qc->tf);
queue_work(ata_wq, &ap->packet_task);
break;
case ATA_PROT_ATAPI_DMA:
+ ap->flags |= ATA_FLAG_NOINTR;
ap->ops->tf_load(ap, &qc->tf); /* load tf registers */
ap->ops->bmdma_setup(qc); /* set up bmdma */
queue_work(ata_wq, &ap->packet_task);
@@ -3242,7 +3399,7 @@
}
/**
- * ata_bmdma_start - Start a PCI IDE BMDMA transaction
+ * ata_bmdma_start_mmio - Start a PCI IDE BMDMA transaction
* @qc: Info associated with this ATA transaction.
*
* LOCKING:
@@ -3413,7 +3570,7 @@
/**
* ata_bmdma_stop - Stop PCI IDE BMDMA transfer
- * @ap: Port associated with this ATA transaction.
+ * @qc: Command we are ending DMA for
*
* Clears the ATA_DMA_START flag in the dma control register
*
@@ -3423,8 +3580,9 @@
* spin_lock_irqsave(host_set lock)
*/
-void ata_bmdma_stop(struct ata_port *ap)
+void ata_bmdma_stop(struct ata_queued_cmd *qc)
{
+ struct ata_port *ap = qc->ap;
if (ap->flags & ATA_FLAG_MMIO) {
void __iomem *mmio = (void __iomem *) ap->ioaddr.bmdma_addr;
@@ -3476,7 +3634,7 @@
goto idle_irq;
/* before we do anything else, clear DMA-Start bit */
- ap->ops->bmdma_stop(ap);
+ ap->ops->bmdma_stop(qc);
/* fall through */
@@ -3551,7 +3709,8 @@
struct ata_port *ap;
ap = host_set->ports[i];
- if (ap && (!(ap->flags & ATA_FLAG_PORT_DISABLED))) {
+ if (ap &&
+ !(ap->flags & (ATA_FLAG_PORT_DISABLED | ATA_FLAG_NOINTR))) {
struct ata_queued_cmd *qc;
qc = ata_qc_from_tag(ap, ap->active_tag);
@@ -3603,19 +3762,27 @@
/* send SCSI cdb */
DPRINTK("send cdb\n");
assert(ap->cdb_len >= 12);
- ata_data_xfer(ap, qc->cdb, ap->cdb_len, 1);
- /* if we are DMA'ing, irq handler takes over from here */
- if (qc->tf.protocol == ATA_PROT_ATAPI_DMA)
- ap->ops->bmdma_start(qc); /* initiate bmdma */
+ if (qc->tf.protocol == ATA_PROT_ATAPI_DMA ||
+ qc->tf.protocol == ATA_PROT_ATAPI_NODATA) {
+ unsigned long flags;
- /* non-data commands are also handled via irq */
- else if (qc->tf.protocol == ATA_PROT_ATAPI_NODATA) {
- /* do nothing */
- }
+ /* Once we're done issuing command and kicking bmdma,
+ * irq handler takes over. To not lose irq, we need
+ * to clear NOINTR flag before sending cdb, but
+ * interrupt handler shouldn't be invoked before we're
+ * finished. Hence, the following locking.
+ */
+ spin_lock_irqsave(&ap->host_set->lock, flags);
+ ap->flags &= ~ATA_FLAG_NOINTR;
+ ata_data_xfer(ap, qc->cdb, ap->cdb_len, 1);
+ if (qc->tf.protocol == ATA_PROT_ATAPI_DMA)
+ ap->ops->bmdma_start(qc); /* initiate bmdma */
+ spin_unlock_irqrestore(&ap->host_set->lock, flags);
+ } else {
+ ata_data_xfer(ap, qc->cdb, ap->cdb_len, 1);
- /* PIO commands are handled by polling */
- else {
+ /* PIO commands are handled by polling */
ap->pio_task_state = PIO_ST;
queue_work(ata_wq, &ap->pio_task);
}
@@ -3623,7 +3790,7 @@
return;
err_out:
- ata_qc_complete(qc, ATA_ERR);
+ ata_poll_qc_complete(qc, ATA_ERR);
}
diff --git a/drivers/scsi/libata-scsi.c b/drivers/scsi/libata-scsi.c
index 6a75ec2..4074e78 100644
--- a/drivers/scsi/libata-scsi.c
+++ b/drivers/scsi/libata-scsi.c
@@ -392,6 +392,60 @@
}
/**
+ * ata_scsi_start_stop_xlat - Translate SCSI START STOP UNIT command
+ * @qc: Storage for translated ATA taskfile
+ * @scsicmd: SCSI command to translate
+ *
+ * Sets up an ATA taskfile to issue STANDBY (to stop) or READ VERIFY
+ * (to start). Perhaps these commands should be preceded by
+ * CHECK POWER MODE to see what power mode the device is already in.
+ * [See SAT revision 5 at www.t10.org]
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host_set lock)
+ *
+ * RETURNS:
+ * Zero on success, non-zero on error.
+ */
+
+static unsigned int ata_scsi_start_stop_xlat(struct ata_queued_cmd *qc,
+ u8 *scsicmd)
+{
+ struct ata_taskfile *tf = &qc->tf;
+
+ tf->flags |= ATA_TFLAG_DEVICE | ATA_TFLAG_ISADDR;
+ tf->protocol = ATA_PROT_NODATA;
+ if (scsicmd[1] & 0x1) {
+ ; /* ignore IMMED bit, violates sat-r05 */
+ }
+ if (scsicmd[4] & 0x2)
+ return 1; /* LOEJ bit set not supported */
+ if (((scsicmd[4] >> 4) & 0xf) != 0)
+ return 1; /* power conditions not supported */
+ if (scsicmd[4] & 0x1) {
+ tf->nsect = 1; /* 1 sector, lba=0 */
+ tf->lbah = 0x0;
+ tf->lbam = 0x0;
+ tf->lbal = 0x0;
+ tf->device |= ATA_LBA;
+ tf->command = ATA_CMD_VERIFY; /* READ VERIFY */
+ } else {
+ tf->nsect = 0; /* time period value (0 implies now) */
+ tf->command = ATA_CMD_STANDBY;
+ /* Consider: ATA STANDBY IMMEDIATE command */
+ }
+ /*
+ * Standby and Idle condition timers could be implemented but that
+ * would require libata to implement the Power condition mode page
+ * and allow the user to change it. Changing mode pages requires
+ * MODE SELECT to be implemented.
+ */
+
+ return 0;
+}
+
+
+/**
* ata_scsi_flush_xlat - Translate SCSI SYNCHRONIZE CACHE command
* @qc: Storage for translated ATA taskfile
* @scsicmd: SCSI command to translate (ignored)
@@ -576,11 +630,19 @@
tf->lbah = scsicmd[3];
VPRINTK("ten-byte command\n");
+ if (qc->nsect == 0) /* we don't support length==0 cmds */
+ return 1;
return 0;
}
if (scsicmd[0] == READ_6 || scsicmd[0] == WRITE_6) {
qc->nsect = tf->nsect = scsicmd[4];
+ if (!qc->nsect) {
+ qc->nsect = 256;
+ if (lba48)
+ tf->hob_nsect = 1;
+ }
+
tf->lbal = scsicmd[3];
tf->lbam = scsicmd[2];
tf->lbah = scsicmd[1] & 0x1f; /* mask out reserved bits */
@@ -620,6 +682,8 @@
tf->lbah = scsicmd[7];
VPRINTK("sixteen-byte command\n");
+ if (qc->nsect == 0) /* we don't support length==0 cmds */
+ return 1;
return 0;
}
@@ -1435,6 +1499,8 @@
case VERIFY:
case VERIFY_16:
return ata_scsi_verify_xlat;
+ case START_STOP:
+ return ata_scsi_start_stop_xlat;
}
return NULL;
diff --git a/drivers/scsi/libata.h b/drivers/scsi/libata.h
index 3e7f4843..620d217 100644
--- a/drivers/scsi/libata.h
+++ b/drivers/scsi/libata.h
@@ -72,7 +72,7 @@
extern void ata_scsi_badcmd(struct scsi_cmnd *cmd,
void (*done)(struct scsi_cmnd *),
u8 asc, u8 ascq);
-extern void ata_scsi_rbuf_fill(struct ata_scsi_args *args,
+extern void ata_scsi_rbuf_fill(struct ata_scsi_args *args,
unsigned int (*actor) (struct ata_scsi_args *args,
u8 *rbuf, unsigned int buflen));
diff --git a/drivers/scsi/sata_nv.c b/drivers/scsi/sata_nv.c
index b0403cc..41a3421 100644
--- a/drivers/scsi/sata_nv.c
+++ b/drivers/scsi/sata_nv.c
@@ -20,6 +20,12 @@
* If you do not delete the provisions above, a recipient may use your
* version of this file under either the OSL or the GPL.
*
+ * 0.08
+ * - Added support for MCP51 and MCP55.
+ *
+ * 0.07
+ * - Added support for RAID class code.
+ *
* 0.06
* - Added generic SATA support by using a pci_device_id that filters on
* the IDE storage class code.
@@ -48,7 +54,7 @@
#include <linux/libata.h>
#define DRV_NAME "sata_nv"
-#define DRV_VERSION "0.6"
+#define DRV_VERSION "0.8"
#define NV_PORTS 2
#define NV_PIO_MASK 0x1f
@@ -116,7 +122,9 @@
GENERIC,
NFORCE2,
NFORCE3,
- CK804
+ CK804,
+ MCP51,
+ MCP55
};
static struct pci_device_id nv_pci_tbl[] = {
@@ -134,9 +142,18 @@
PCI_ANY_ID, PCI_ANY_ID, 0, 0, CK804 },
{ PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP04_SATA2,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, CK804 },
+ { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_SATA,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0, MCP51 },
+ { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_SATA2,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0, MCP51 },
+ { PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_SATA,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0, MCP55 },
{ PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID,
PCI_ANY_ID, PCI_ANY_ID,
PCI_CLASS_STORAGE_IDE<<8, 0xffff00, GENERIC },
+ { PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID,
+ PCI_ANY_ID, PCI_ANY_ID,
+ PCI_CLASS_STORAGE_RAID<<8, 0xffff00, GENERIC },
{ 0, } /* terminate list */
};
@@ -274,7 +291,8 @@
struct ata_port *ap;
ap = host_set->ports[i];
- if (ap && (!(ap->flags & ATA_FLAG_PORT_DISABLED))) {
+ if (ap &&
+ !(ap->flags & (ATA_FLAG_PORT_DISABLED | ATA_FLAG_NOINTR))) {
struct ata_queued_cmd *qc;
qc = ata_qc_from_tag(ap, ap->active_tag);
diff --git a/drivers/scsi/sata_promise.c b/drivers/scsi/sata_promise.c
index 919fb31..b8dc49f 100644
--- a/drivers/scsi/sata_promise.c
+++ b/drivers/scsi/sata_promise.c
@@ -181,6 +181,10 @@
board_20319 },
{ PCI_VENDOR_ID_PROMISE, 0x3319, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
board_20319 },
+ { PCI_VENDOR_ID_PROMISE, 0x3519, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ board_20319 },
+ { PCI_VENDOR_ID_PROMISE, 0x3d17, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ board_20319 },
{ PCI_VENDOR_ID_PROMISE, 0x3d18, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
board_20319 },
@@ -321,11 +325,15 @@
static void pdc_eng_timeout(struct ata_port *ap)
{
+ struct ata_host_set *host_set = ap->host_set;
u8 drv_stat;
struct ata_queued_cmd *qc;
+ unsigned long flags;
DPRINTK("ENTER\n");
+ spin_lock_irqsave(&host_set->lock, flags);
+
qc = ata_qc_from_tag(ap, ap->active_tag);
if (!qc) {
printk(KERN_ERR "ata%u: BUG: timeout without command\n",
@@ -359,6 +367,7 @@
}
out:
+ spin_unlock_irqrestore(&host_set->lock, flags);
DPRINTK("EXIT\n");
}
@@ -441,7 +450,8 @@
VPRINTK("port %u\n", i);
ap = host_set->ports[i];
tmp = mask & (1 << (i + 1));
- if (tmp && ap && (!(ap->flags & ATA_FLAG_PORT_DISABLED))) {
+ if (tmp && ap &&
+ !(ap->flags & (ATA_FLAG_PORT_DISABLED | ATA_FLAG_NOINTR))) {
struct ata_queued_cmd *qc;
qc = ata_qc_from_tag(ap, ap->active_tag);
diff --git a/drivers/scsi/sata_qstor.c b/drivers/scsi/sata_qstor.c
index 1383e8a..93fd06f 100644
--- a/drivers/scsi/sata_qstor.c
+++ b/drivers/scsi/sata_qstor.c
@@ -117,7 +117,7 @@
static void qs_qc_prep(struct ata_queued_cmd *qc);
static int qs_qc_issue(struct ata_queued_cmd *qc);
static int qs_check_atapi_dma(struct ata_queued_cmd *qc);
-static void qs_bmdma_stop(struct ata_port *ap);
+static void qs_bmdma_stop(struct ata_queued_cmd *qc);
static u8 qs_bmdma_status(struct ata_port *ap);
static void qs_irq_clear(struct ata_port *ap);
static void qs_eng_timeout(struct ata_port *ap);
@@ -198,7 +198,7 @@
return 1; /* ATAPI DMA not supported */
}
-static void qs_bmdma_stop(struct ata_port *ap)
+static void qs_bmdma_stop(struct ata_queued_cmd *qc)
{
/* nothing */
}
@@ -386,7 +386,8 @@
DPRINTK("SFF=%08x%08x: sCHAN=%u sHST=%d sDST=%02x\n",
sff1, sff0, port_no, sHST, sDST);
handled = 1;
- if (ap && (!(ap->flags & ATA_FLAG_PORT_DISABLED))) {
+ if (ap && !(ap->flags &
+ (ATA_FLAG_PORT_DISABLED|ATA_FLAG_NOINTR))) {
struct ata_queued_cmd *qc;
struct qs_port_priv *pp = ap->private_data;
if (!pp || pp->state != qs_state_pkt)
@@ -417,7 +418,8 @@
for (port_no = 0; port_no < host_set->n_ports; ++port_no) {
struct ata_port *ap;
ap = host_set->ports[port_no];
- if (ap && (!(ap->flags & ATA_FLAG_PORT_DISABLED))) {
+ if (ap &&
+ !(ap->flags & (ATA_FLAG_PORT_DISABLED | ATA_FLAG_NOINTR))) {
struct ata_queued_cmd *qc;
struct qs_port_priv *pp = ap->private_data;
if (!pp || pp->state != qs_state_mmio)
@@ -431,7 +433,7 @@
continue;
DPRINTK("ata%u: protocol %d (dev_stat 0x%X)\n",
ap->id, qc->tf.protocol, status);
-
+
/* complete taskfile transaction */
pp->state = qs_state_idle;
ata_qc_complete(qc, status);
diff --git a/drivers/scsi/sata_sil.c b/drivers/scsi/sata_sil.c
index 49ed557..9d24d6c 100644
--- a/drivers/scsi/sata_sil.c
+++ b/drivers/scsi/sata_sil.c
@@ -24,6 +24,11 @@
* If you do not delete the provisions above, a recipient may use your
* version of this file under either the OSL or the GPL.
*
+ * Documentation for SiI 3112:
+ * http://gkernel.sourceforge.net/specs/sii/3112A_SiI-DS-0095-B2.pdf.bz2
+ *
+ * Other errata and documentation available under NDA.
+ *
*/
#include <linux/kernel.h>
@@ -41,8 +46,11 @@
#define DRV_VERSION "0.9"
enum {
+ SIL_FLAG_MOD15WRITE = (1 << 30),
+
sil_3112 = 0,
- sil_3114 = 1,
+ sil_3112_m15w = 1,
+ sil_3114 = 2,
SIL_FIFO_R0 = 0x40,
SIL_FIFO_W0 = 0x41,
@@ -76,13 +84,13 @@
static void sil_post_set_mode (struct ata_port *ap);
static struct pci_device_id sil_pci_tbl[] = {
- { 0x1095, 0x3112, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112 },
- { 0x1095, 0x0240, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112 },
+ { 0x1095, 0x3112, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112_m15w },
+ { 0x1095, 0x0240, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112_m15w },
{ 0x1095, 0x3512, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112 },
{ 0x1095, 0x3114, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3114 },
- { 0x1002, 0x436e, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112 },
- { 0x1002, 0x4379, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112 },
- { 0x1002, 0x437a, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112 },
+ { 0x1002, 0x436e, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112_m15w },
+ { 0x1002, 0x4379, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112_m15w },
+ { 0x1002, 0x437a, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112_m15w },
{ } /* terminate list */
};
@@ -174,6 +182,16 @@
.mwdma_mask = 0x07, /* mwdma0-2 */
.udma_mask = 0x3f, /* udma0-5 */
.port_ops = &sil_ops,
+ }, /* sil_3112_15w - keep it sync'd w/ sil_3112 */
+ {
+ .sht = &sil_sht,
+ .host_flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
+ ATA_FLAG_SRST | ATA_FLAG_MMIO |
+ SIL_FLAG_MOD15WRITE,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x07, /* mwdma0-2 */
+ .udma_mask = 0x3f, /* udma0-5 */
+ .port_ops = &sil_ops,
}, /* sil_3114 */
{
.sht = &sil_sht,
@@ -323,15 +341,15 @@
while ((len > 0) && (s[len - 1] == ' '))
len--;
- for (n = 0; sil_blacklist[n].product; n++)
+ for (n = 0; sil_blacklist[n].product; n++)
if (!memcmp(sil_blacklist[n].product, s,
strlen(sil_blacklist[n].product))) {
quirks = sil_blacklist[n].quirk;
break;
}
-
+
/* limit requests to 15 sectors */
- if (quirks & SIL_QUIRK_MOD15WRITE) {
+ if ((ap->flags & SIL_FLAG_MOD15WRITE) && (quirks & SIL_QUIRK_MOD15WRITE)) {
printk(KERN_INFO "ata%u(%u): applying Seagate errata fix\n",
ap->id, dev->devno);
ap->host->max_sectors = 15;
diff --git a/drivers/scsi/sata_sis.c b/drivers/scsi/sata_sis.c
index e418b89..b250ae0 100644
--- a/drivers/scsi/sata_sis.c
+++ b/drivers/scsi/sata_sis.c
@@ -234,7 +234,7 @@
pci_read_config_dword(pdev, SIS_GENCTL, &genctl);
if ((genctl & GENCTL_IOMAPPED_SCR) == 0)
probe_ent->host_flags |= SIS_FLAG_CFGSCR;
-
+
/* if hardware thinks SCRs are in IO space, but there are
* no IO resources assigned, change to PCI cfg space.
*/
diff --git a/drivers/scsi/sata_svw.c b/drivers/scsi/sata_svw.c
index 858e071..6fd2ce1 100644
--- a/drivers/scsi/sata_svw.c
+++ b/drivers/scsi/sata_svw.c
@@ -195,18 +195,18 @@
/* start host DMA transaction */
dmactl = readb(mmio + ATA_DMA_CMD);
writeb(dmactl | ATA_DMA_START, mmio + ATA_DMA_CMD);
- /* There is a race condition in certain SATA controllers that can
- be seen when the r/w command is given to the controller before the
+ /* There is a race condition in certain SATA controllers that can
+ be seen when the r/w command is given to the controller before the
host DMA is started. On a Read command, the controller would initiate
the command to the drive even before it sees the DMA start. When there
- are very fast drives connected to the controller, or when the data request
+ are very fast drives connected to the controller, or when the data request
hits in the drive cache, there is the possibility that the drive returns a part
or all of the requested data to the controller before the DMA start is issued.
In this case, the controller would become confused as to what to do with the data.
In the worst case when all the data is returned back to the controller, the
controller could hang. In other cases it could return partial data returning
in data corruption. This problem has been seen in PPC systems and can also appear
- on an system with very fast disks, where the SATA controller is sitting behind a
+ on an system with very fast disks, where the SATA controller is sitting behind a
number of bridges, and hence there is significant latency between the r/w command
and the start command. */
/* issue r/w command if the access is to ATA*/
@@ -214,7 +214,7 @@
ap->ops->exec_command(ap, &qc->tf);
}
-
+
static u8 k2_stat_check_status(struct ata_port *ap)
{
return readl((void *) ap->ioaddr.status_addr);
diff --git a/drivers/scsi/sata_sx4.c b/drivers/scsi/sata_sx4.c
index efd7d7a..a20d428 100644
--- a/drivers/scsi/sata_sx4.c
+++ b/drivers/scsi/sata_sx4.c
@@ -94,7 +94,7 @@
PDC_DIMM1_CONTROL_OFFSET = 0x84,
PDC_SDRAM_CONTROL_OFFSET = 0x88,
PDC_I2C_WRITE = 0x00000000,
- PDC_I2C_READ = 0x00000040,
+ PDC_I2C_READ = 0x00000040,
PDC_I2C_START = 0x00000080,
PDC_I2C_MASK_INT = 0x00000020,
PDC_I2C_COMPLETE = 0x00010000,
@@ -105,16 +105,16 @@
PDC_DIMM_SPD_COLUMN_NUM = 4,
PDC_DIMM_SPD_MODULE_ROW = 5,
PDC_DIMM_SPD_TYPE = 11,
- PDC_DIMM_SPD_FRESH_RATE = 12,
- PDC_DIMM_SPD_BANK_NUM = 17,
+ PDC_DIMM_SPD_FRESH_RATE = 12,
+ PDC_DIMM_SPD_BANK_NUM = 17,
PDC_DIMM_SPD_CAS_LATENCY = 18,
- PDC_DIMM_SPD_ATTRIBUTE = 21,
+ PDC_DIMM_SPD_ATTRIBUTE = 21,
PDC_DIMM_SPD_ROW_PRE_CHARGE = 27,
- PDC_DIMM_SPD_ROW_ACTIVE_DELAY = 28,
+ PDC_DIMM_SPD_ROW_ACTIVE_DELAY = 28,
PDC_DIMM_SPD_RAS_CAS_DELAY = 29,
PDC_DIMM_SPD_ACTIVE_PRECHARGE = 30,
PDC_DIMM_SPD_SYSTEM_FREQ = 126,
- PDC_CTL_STATUS = 0x08,
+ PDC_CTL_STATUS = 0x08,
PDC_DIMM_WINDOW_CTLR = 0x0C,
PDC_TIME_CONTROL = 0x3C,
PDC_TIME_PERIOD = 0x40,
@@ -157,15 +157,15 @@
static void pdc20621_host_stop(struct ata_host_set *host_set);
static unsigned int pdc20621_dimm_init(struct ata_probe_ent *pe);
static int pdc20621_detect_dimm(struct ata_probe_ent *pe);
-static unsigned int pdc20621_i2c_read(struct ata_probe_ent *pe,
+static unsigned int pdc20621_i2c_read(struct ata_probe_ent *pe,
u32 device, u32 subaddr, u32 *pdata);
static int pdc20621_prog_dimm0(struct ata_probe_ent *pe);
static unsigned int pdc20621_prog_dimm_global(struct ata_probe_ent *pe);
#ifdef ATA_VERBOSE_DEBUG
-static void pdc20621_get_from_dimm(struct ata_probe_ent *pe,
+static void pdc20621_get_from_dimm(struct ata_probe_ent *pe,
void *psource, u32 offset, u32 size);
#endif
-static void pdc20621_put_to_dimm(struct ata_probe_ent *pe,
+static void pdc20621_put_to_dimm(struct ata_probe_ent *pe,
void *psource, u32 offset, u32 size);
static void pdc20621_irq_clear(struct ata_port *ap);
static int pdc20621_qc_issue_prot(struct ata_queued_cmd *qc);
@@ -825,7 +825,8 @@
ap = host_set->ports[port_no];
tmp = mask & (1 << i);
VPRINTK("seq %u, port_no %u, ap %p, tmp %x\n", i, port_no, ap, tmp);
- if (tmp && ap && (!(ap->flags & ATA_FLAG_PORT_DISABLED))) {
+ if (tmp && ap &&
+ !(ap->flags & (ATA_FLAG_PORT_DISABLED | ATA_FLAG_NOINTR))) {
struct ata_queued_cmd *qc;
qc = ata_qc_from_tag(ap, ap->active_tag);
@@ -847,10 +848,14 @@
static void pdc_eng_timeout(struct ata_port *ap)
{
u8 drv_stat;
+ struct ata_host_set *host_set = ap->host_set;
struct ata_queued_cmd *qc;
+ unsigned long flags;
DPRINTK("ENTER\n");
+ spin_lock_irqsave(&host_set->lock, flags);
+
qc = ata_qc_from_tag(ap, ap->active_tag);
if (!qc) {
printk(KERN_ERR "ata%u: BUG: timeout without command\n",
@@ -884,6 +889,7 @@
}
out:
+ spin_unlock_irqrestore(&host_set->lock, flags);
DPRINTK("EXIT\n");
}
@@ -922,7 +928,7 @@
#ifdef ATA_VERBOSE_DEBUG
-static void pdc20621_get_from_dimm(struct ata_probe_ent *pe, void *psource,
+static void pdc20621_get_from_dimm(struct ata_probe_ent *pe, void *psource,
u32 offset, u32 size)
{
u32 window_size;
@@ -936,9 +942,9 @@
/* hard-code chip #0 */
mmio += PDC_CHIP0_OFS;
- page_mask = 0x00;
- window_size = 0x2000 * 4; /* 32K byte uchar size */
- idx = (u16) (offset / window_size);
+ page_mask = 0x00;
+ window_size = 0x2000 * 4; /* 32K byte uchar size */
+ idx = (u16) (offset / window_size);
writel(0x01, mmio + PDC_GENERAL_CTLR);
readl(mmio + PDC_GENERAL_CTLR);
@@ -947,19 +953,19 @@
offset -= (idx * window_size);
idx++;
- dist = ((long) (window_size - (offset + size))) >= 0 ? size :
+ dist = ((long) (window_size - (offset + size))) >= 0 ? size :
(long) (window_size - offset);
- memcpy_fromio((char *) psource, (char *) (dimm_mmio + offset / 4),
+ memcpy_fromio((char *) psource, (char *) (dimm_mmio + offset / 4),
dist);
- psource += dist;
+ psource += dist;
size -= dist;
for (; (long) size >= (long) window_size ;) {
writel(0x01, mmio + PDC_GENERAL_CTLR);
readl(mmio + PDC_GENERAL_CTLR);
writel(((idx) << page_mask), mmio + PDC_DIMM_WINDOW_CTLR);
readl(mmio + PDC_DIMM_WINDOW_CTLR);
- memcpy_fromio((char *) psource, (char *) (dimm_mmio),
+ memcpy_fromio((char *) psource, (char *) (dimm_mmio),
window_size / 4);
psource += window_size;
size -= window_size;
@@ -971,14 +977,14 @@
readl(mmio + PDC_GENERAL_CTLR);
writel(((idx) << page_mask), mmio + PDC_DIMM_WINDOW_CTLR);
readl(mmio + PDC_DIMM_WINDOW_CTLR);
- memcpy_fromio((char *) psource, (char *) (dimm_mmio),
+ memcpy_fromio((char *) psource, (char *) (dimm_mmio),
size / 4);
}
}
#endif
-static void pdc20621_put_to_dimm(struct ata_probe_ent *pe, void *psource,
+static void pdc20621_put_to_dimm(struct ata_probe_ent *pe, void *psource,
u32 offset, u32 size)
{
u32 window_size;
@@ -989,16 +995,16 @@
struct pdc_host_priv *hpriv = pe->private_data;
void *dimm_mmio = hpriv->dimm_mmio;
- /* hard-code chip #0 */
+ /* hard-code chip #0 */
mmio += PDC_CHIP0_OFS;
- page_mask = 0x00;
- window_size = 0x2000 * 4; /* 32K byte uchar size */
+ page_mask = 0x00;
+ window_size = 0x2000 * 4; /* 32K byte uchar size */
idx = (u16) (offset / window_size);
writel(((idx) << page_mask), mmio + PDC_DIMM_WINDOW_CTLR);
readl(mmio + PDC_DIMM_WINDOW_CTLR);
- offset -= (idx * window_size);
+ offset -= (idx * window_size);
idx++;
dist = ((long)(s32)(window_size - (offset + size))) >= 0 ? size :
(long) (window_size - offset);
@@ -1006,12 +1012,12 @@
writel(0x01, mmio + PDC_GENERAL_CTLR);
readl(mmio + PDC_GENERAL_CTLR);
- psource += dist;
+ psource += dist;
size -= dist;
for (; (long) size >= (long) window_size ;) {
writel(((idx) << page_mask), mmio + PDC_DIMM_WINDOW_CTLR);
readl(mmio + PDC_DIMM_WINDOW_CTLR);
- memcpy_toio((char *) (dimm_mmio), (char *) psource,
+ memcpy_toio((char *) (dimm_mmio), (char *) psource,
window_size / 4);
writel(0x01, mmio + PDC_GENERAL_CTLR);
readl(mmio + PDC_GENERAL_CTLR);
@@ -1019,7 +1025,7 @@
size -= window_size;
idx ++;
}
-
+
if (size) {
writel(((idx) << page_mask), mmio + PDC_DIMM_WINDOW_CTLR);
readl(mmio + PDC_DIMM_WINDOW_CTLR);
@@ -1030,12 +1036,12 @@
}
-static unsigned int pdc20621_i2c_read(struct ata_probe_ent *pe, u32 device,
+static unsigned int pdc20621_i2c_read(struct ata_probe_ent *pe, u32 device,
u32 subaddr, u32 *pdata)
{
void *mmio = pe->mmio_base;
u32 i2creg = 0;
- u32 status;
+ u32 status;
u32 count =0;
/* hard-code chip #0 */
@@ -1049,7 +1055,7 @@
readl(mmio + PDC_I2C_ADDR_DATA_OFFSET);
/* Write Control to perform read operation, mask int */
- writel(PDC_I2C_READ | PDC_I2C_START | PDC_I2C_MASK_INT,
+ writel(PDC_I2C_READ | PDC_I2C_START | PDC_I2C_MASK_INT,
mmio + PDC_I2C_CONTROL_OFFSET);
for (count = 0; count <= 1000; count ++) {
@@ -1062,26 +1068,26 @@
}
*pdata = (status >> 8) & 0x000000ff;
- return 1;
+ return 1;
}
static int pdc20621_detect_dimm(struct ata_probe_ent *pe)
{
u32 data=0 ;
- if (pdc20621_i2c_read(pe, PDC_DIMM0_SPD_DEV_ADDRESS,
+ if (pdc20621_i2c_read(pe, PDC_DIMM0_SPD_DEV_ADDRESS,
PDC_DIMM_SPD_SYSTEM_FREQ, &data)) {
if (data == 100)
return 100;
} else
return 0;
-
+
if (pdc20621_i2c_read(pe, PDC_DIMM0_SPD_DEV_ADDRESS, 9, &data)) {
- if(data <= 0x75)
+ if(data <= 0x75)
return 133;
} else
return 0;
-
+
return 0;
}
@@ -1091,15 +1097,15 @@
u32 spd0[50];
u32 data = 0;
int size, i;
- u8 bdimmsize;
+ u8 bdimmsize;
void *mmio = pe->mmio_base;
static const struct {
unsigned int reg;
unsigned int ofs;
} pdc_i2c_read_data [] = {
- { PDC_DIMM_SPD_TYPE, 11 },
+ { PDC_DIMM_SPD_TYPE, 11 },
{ PDC_DIMM_SPD_FRESH_RATE, 12 },
- { PDC_DIMM_SPD_COLUMN_NUM, 4 },
+ { PDC_DIMM_SPD_COLUMN_NUM, 4 },
{ PDC_DIMM_SPD_ATTRIBUTE, 21 },
{ PDC_DIMM_SPD_ROW_NUM, 3 },
{ PDC_DIMM_SPD_BANK_NUM, 17 },
@@ -1108,7 +1114,7 @@
{ PDC_DIMM_SPD_ROW_ACTIVE_DELAY, 28 },
{ PDC_DIMM_SPD_RAS_CAS_DELAY, 29 },
{ PDC_DIMM_SPD_ACTIVE_PRECHARGE, 30 },
- { PDC_DIMM_SPD_CAS_LATENCY, 18 },
+ { PDC_DIMM_SPD_CAS_LATENCY, 18 },
};
/* hard-code chip #0 */
@@ -1116,17 +1122,17 @@
for(i=0; i<ARRAY_SIZE(pdc_i2c_read_data); i++)
pdc20621_i2c_read(pe, PDC_DIMM0_SPD_DEV_ADDRESS,
- pdc_i2c_read_data[i].reg,
+ pdc_i2c_read_data[i].reg,
&spd0[pdc_i2c_read_data[i].ofs]);
-
+
data |= (spd0[4] - 8) | ((spd0[21] != 0) << 3) | ((spd0[3]-11) << 4);
- data |= ((spd0[17] / 4) << 6) | ((spd0[5] / 2) << 7) |
+ data |= ((spd0[17] / 4) << 6) | ((spd0[5] / 2) << 7) |
((((spd0[27] + 9) / 10) - 1) << 8) ;
- data |= (((((spd0[29] > spd0[28])
- ? spd0[29] : spd0[28]) + 9) / 10) - 1) << 10;
+ data |= (((((spd0[29] > spd0[28])
+ ? spd0[29] : spd0[28]) + 9) / 10) - 1) << 10;
data |= ((spd0[30] - spd0[29] + 9) / 10 - 2) << 12;
-
- if (spd0[18] & 0x08)
+
+ if (spd0[18] & 0x08)
data |= ((0x03) << 14);
else if (spd0[18] & 0x04)
data |= ((0x02) << 14);
@@ -1135,7 +1141,7 @@
else
data |= (0 << 14);
- /*
+ /*
Calculate the size of bDIMMSize (power of 2) and
merge the DIMM size by program start/end address.
*/
@@ -1145,9 +1151,9 @@
data |= (((size / 16) - 1) << 16);
data |= (0 << 23);
data |= 8;
- writel(data, mmio + PDC_DIMM0_CONTROL_OFFSET);
+ writel(data, mmio + PDC_DIMM0_CONTROL_OFFSET);
readl(mmio + PDC_DIMM0_CONTROL_OFFSET);
- return size;
+ return size;
}
@@ -1167,12 +1173,12 @@
Refresh Enable (bit 17)
*/
- data = 0x022259F1;
+ data = 0x022259F1;
writel(data, mmio + PDC_SDRAM_CONTROL_OFFSET);
readl(mmio + PDC_SDRAM_CONTROL_OFFSET);
/* Turn on for ECC */
- pdc20621_i2c_read(pe, PDC_DIMM0_SPD_DEV_ADDRESS,
+ pdc20621_i2c_read(pe, PDC_DIMM0_SPD_DEV_ADDRESS,
PDC_DIMM_SPD_TYPE, &spd0);
if (spd0 == 0x02) {
data |= (0x01 << 16);
@@ -1186,22 +1192,22 @@
data |= (1<<19);
writel(data, mmio + PDC_SDRAM_CONTROL_OFFSET);
- error = 1;
+ error = 1;
for (i = 1; i <= 10; i++) { /* polling ~5 secs */
data = readl(mmio + PDC_SDRAM_CONTROL_OFFSET);
if (!(data & (1<<19))) {
error = 0;
- break;
+ break;
}
msleep(i*100);
}
return error;
}
-
+
static unsigned int pdc20621_dimm_init(struct ata_probe_ent *pe)
{
- int speed, size, length;
+ int speed, size, length;
u32 addr,spd0,pci_status;
u32 tmp=0;
u32 time_period=0;
@@ -1228,7 +1234,7 @@
/* Wait 3 seconds */
msleep(3000);
- /*
+ /*
When timer is enabled, counter is decreased every internal
clock cycle.
*/
@@ -1236,24 +1242,24 @@
tcount = readl(mmio + PDC_TIME_COUNTER);
VPRINTK("Time Counter Register (0x44): 0x%x\n", tcount);
- /*
+ /*
If SX4 is on PCI-X bus, after 3 seconds, the timer counter
register should be >= (0xffffffff - 3x10^8).
*/
if(tcount >= PCI_X_TCOUNT) {
ticks = (time_period - tcount);
VPRINTK("Num counters 0x%x (%d)\n", ticks, ticks);
-
+
clock = (ticks / 300000);
VPRINTK("10 * Internal clk = 0x%x (%d)\n", clock, clock);
-
+
clock = (clock * 33);
VPRINTK("10 * Internal clk * 33 = 0x%x (%d)\n", clock, clock);
/* PLL F Param (bit 22:16) */
fparam = (1400000 / clock) - 2;
VPRINTK("PLL F Param: 0x%x (%d)\n", fparam, fparam);
-
+
/* OD param = 0x2 (bit 31:30), R param = 0x5 (bit 29:25) */
pci_status = (0x8a001824 | (fparam << 16));
} else
@@ -1264,21 +1270,21 @@
writel(pci_status, mmio + PDC_CTL_STATUS);
readl(mmio + PDC_CTL_STATUS);
- /*
+ /*
Read SPD of DIMM by I2C interface,
and program the DIMM Module Controller.
*/
if (!(speed = pdc20621_detect_dimm(pe))) {
- printk(KERN_ERR "Detect Local DIMM Fail\n");
+ printk(KERN_ERR "Detect Local DIMM Fail\n");
return 1; /* DIMM error */
}
VPRINTK("Local DIMM Speed = %d\n", speed);
- /* Programming DIMM0 Module Control Register (index_CID0:80h) */
+ /* Programming DIMM0 Module Control Register (index_CID0:80h) */
size = pdc20621_prog_dimm0(pe);
VPRINTK("Local DIMM Size = %dMB\n",size);
- /* Programming DIMM Module Global Control Register (index_CID0:88h) */
+ /* Programming DIMM Module Global Control Register (index_CID0:88h) */
if (pdc20621_prog_dimm_global(pe)) {
printk(KERN_ERR "Programming DIMM Module Global Control Register Fail\n");
return 1;
@@ -1297,30 +1303,30 @@
pdc20621_put_to_dimm(pe, (void *) test_parttern1, 0x10040, 40);
pdc20621_get_from_dimm(pe, (void *) test_parttern2, 0x40, 40);
- printk(KERN_ERR "%x, %x, %s\n", test_parttern2[0],
+ printk(KERN_ERR "%x, %x, %s\n", test_parttern2[0],
test_parttern2[1], &(test_parttern2[2]));
- pdc20621_get_from_dimm(pe, (void *) test_parttern2, 0x10040,
+ pdc20621_get_from_dimm(pe, (void *) test_parttern2, 0x10040,
40);
- printk(KERN_ERR "%x, %x, %s\n", test_parttern2[0],
+ printk(KERN_ERR "%x, %x, %s\n", test_parttern2[0],
test_parttern2[1], &(test_parttern2[2]));
pdc20621_put_to_dimm(pe, (void *) test_parttern1, 0x40, 40);
pdc20621_get_from_dimm(pe, (void *) test_parttern2, 0x40, 40);
- printk(KERN_ERR "%x, %x, %s\n", test_parttern2[0],
+ printk(KERN_ERR "%x, %x, %s\n", test_parttern2[0],
test_parttern2[1], &(test_parttern2[2]));
}
#endif
/* ECC initiliazation. */
- pdc20621_i2c_read(pe, PDC_DIMM0_SPD_DEV_ADDRESS,
+ pdc20621_i2c_read(pe, PDC_DIMM0_SPD_DEV_ADDRESS,
PDC_DIMM_SPD_TYPE, &spd0);
if (spd0 == 0x02) {
VPRINTK("Start ECC initialization\n");
addr = 0;
length = size * 1024 * 1024;
while (addr < length) {
- pdc20621_put_to_dimm(pe, (void *) &tmp, addr,
+ pdc20621_put_to_dimm(pe, (void *) &tmp, addr,
sizeof(u32));
addr += sizeof(u32);
}
diff --git a/drivers/scsi/sata_uli.c b/drivers/scsi/sata_uli.c
index a71fb54..eb202a7 100644
--- a/drivers/scsi/sata_uli.c
+++ b/drivers/scsi/sata_uli.c
@@ -214,7 +214,7 @@
rc = -ENOMEM;
goto err_out_regions;
}
-
+
switch (board_idx) {
case uli_5287:
probe_ent->port[0].scr_addr = ULI5287_BASE;
diff --git a/drivers/scsi/sata_via.c b/drivers/scsi/sata_via.c
index f43183c..feff109 100644
--- a/drivers/scsi/sata_via.c
+++ b/drivers/scsi/sata_via.c
@@ -347,7 +347,7 @@
probe_ent = vt6420_init_probe_ent(pdev);
else
probe_ent = vt6421_init_probe_ent(pdev);
-
+
if (!probe_ent) {
printk(KERN_ERR DRV_NAME "(%s): out of memory\n",
pci_name(pdev));
diff --git a/drivers/scsi/sata_vsc.c b/drivers/scsi/sata_vsc.c
index c5e09dc..6f25621 100644
--- a/drivers/scsi/sata_vsc.c
+++ b/drivers/scsi/sata_vsc.c
@@ -173,7 +173,8 @@
struct ata_port *ap;
ap = host_set->ports[i];
- if (ap && (!(ap->flags & ATA_FLAG_PORT_DISABLED))) {
+ if (ap && !(ap->flags &
+ (ATA_FLAG_PORT_DISABLED|ATA_FLAG_NOINTR))) {
struct ata_queued_cmd *qc;
qc = ata_qc_from_tag(ap, ap->active_tag);
@@ -342,7 +343,7 @@
pci_set_master(pdev);
- /*
+ /*
* Config offset 0x98 is "Extended Control and Status Register 0"
* Default value is (1 << 28). All bits except bit 28 are reserved in
* DPA mode. If bit 28 is set, LED 0 reflects all ports' activity.
diff --git a/drivers/scsi/sg.c b/drivers/scsi/sg.c
index 51292f2..e822ca0 100644
--- a/drivers/scsi/sg.c
+++ b/drivers/scsi/sg.c
@@ -2971,23 +2971,22 @@
{
struct sg_proc_deviter * it = kmalloc(sizeof(*it), GFP_KERNEL);
+ s->private = it;
if (! it)
return NULL;
+
if (NULL == sg_dev_arr)
- goto err1;
+ return NULL;
it->index = *pos;
it->max = sg_last_dev();
if (it->index >= it->max)
- goto err1;
+ return NULL;
return it;
-err1:
- kfree(it);
- return NULL;
}
static void * dev_seq_next(struct seq_file *s, void *v, loff_t *pos)
{
- struct sg_proc_deviter * it = (struct sg_proc_deviter *) v;
+ struct sg_proc_deviter * it = s->private;
*pos = ++it->index;
return (it->index < it->max) ? it : NULL;
@@ -2995,7 +2994,7 @@
static void dev_seq_stop(struct seq_file *s, void *v)
{
- kfree (v);
+ kfree(s->private);
}
static int sg_proc_open_dev(struct inode *inode, struct file *file)
diff --git a/drivers/serial/8250_pci.c b/drivers/serial/8250_pci.c
index 07f05e9..0e21f58 100644
--- a/drivers/serial/8250_pci.c
+++ b/drivers/serial/8250_pci.c
@@ -34,36 +34,6 @@
#undef SERIAL_DEBUG_PCI
/*
- * Definitions for PCI support.
- */
-#define FL_BASE_MASK 0x0007
-#define FL_BASE0 0x0000
-#define FL_BASE1 0x0001
-#define FL_BASE2 0x0002
-#define FL_BASE3 0x0003
-#define FL_BASE4 0x0004
-#define FL_GET_BASE(x) (x & FL_BASE_MASK)
-
-/* Use successive BARs (PCI base address registers),
- else use offset into some specified BAR */
-#define FL_BASE_BARS 0x0008
-
-/* do not assign an irq */
-#define FL_NOIRQ 0x0080
-
-/* Use the Base address register size to cap number of ports */
-#define FL_REGION_SZ_CAP 0x0100
-
-struct pci_board {
- unsigned int flags;
- unsigned int num_ports;
- unsigned int base_baud;
- unsigned int uart_offset;
- unsigned int reg_shift;
- unsigned int first_offset;
-};
-
-/*
* init function returns:
* > 0 - number of ports
* = 0 - use board->num_ports
@@ -75,14 +45,15 @@
u32 subvendor;
u32 subdevice;
int (*init)(struct pci_dev *dev);
- int (*setup)(struct pci_dev *dev, struct pci_board *board,
- struct uart_port *port, int idx);
+ int (*setup)(struct serial_private *, struct pciserial_board *,
+ struct uart_port *, int);
void (*exit)(struct pci_dev *dev);
};
#define PCI_NUM_BAR_RESOURCES 6
struct serial_private {
+ struct pci_dev *dev;
unsigned int nr;
void __iomem *remapped_bar[PCI_NUM_BAR_RESOURCES];
struct pci_serial_quirk *quirk;
@@ -101,17 +72,18 @@
}
static int
-setup_port(struct pci_dev *dev, struct uart_port *port,
+setup_port(struct serial_private *priv, struct uart_port *port,
int bar, int offset, int regshift)
{
- struct serial_private *priv = pci_get_drvdata(dev);
+ struct pci_dev *dev = priv->dev;
unsigned long base, len;
if (bar >= PCI_NUM_BAR_RESOURCES)
return -EINVAL;
+ base = pci_resource_start(dev, bar);
+
if (pci_resource_flags(dev, bar) & IORESOURCE_MEM) {
- base = pci_resource_start(dev, bar);
len = pci_resource_len(dev, bar);
if (!priv->remapped_bar[bar])
@@ -120,13 +92,16 @@
return -ENOMEM;
port->iotype = UPIO_MEM;
+ port->iobase = 0;
port->mapbase = base + offset;
port->membase = priv->remapped_bar[bar] + offset;
port->regshift = regshift;
} else {
- base = pci_resource_start(dev, bar) + offset;
port->iotype = UPIO_PORT;
- port->iobase = base;
+ port->iobase = base + offset;
+ port->mapbase = 0;
+ port->membase = NULL;
+ port->regshift = 0;
}
return 0;
}
@@ -136,7 +111,7 @@
* Not that ugly ;) -- HW
*/
static int
-afavlab_setup(struct pci_dev *dev, struct pci_board *board,
+afavlab_setup(struct serial_private *priv, struct pciserial_board *board,
struct uart_port *port, int idx)
{
unsigned int bar, offset = board->first_offset;
@@ -149,7 +124,7 @@
offset += (idx - 4) * board->uart_offset;
}
- return setup_port(dev, port, bar, offset, board->reg_shift);
+ return setup_port(priv, port, bar, offset, board->reg_shift);
}
/*
@@ -189,13 +164,13 @@
* some serial ports are supposed to be hidden on certain models.
*/
static int
-pci_hp_diva_setup(struct pci_dev *dev, struct pci_board *board,
+pci_hp_diva_setup(struct serial_private *priv, struct pciserial_board *board,
struct uart_port *port, int idx)
{
unsigned int offset = board->first_offset;
unsigned int bar = FL_GET_BASE(board->flags);
- switch (dev->subsystem_device) {
+ switch (priv->dev->subsystem_device) {
case PCI_DEVICE_ID_HP_DIVA_MAESTRO:
if (idx == 3)
idx++;
@@ -212,7 +187,7 @@
offset += idx * board->uart_offset;
- return setup_port(dev, port, bar, offset, board->reg_shift);
+ return setup_port(priv, port, bar, offset, board->reg_shift);
}
/*
@@ -307,7 +282,7 @@
/* SBS Technologies Inc. PMC-OCTPRO and P-OCTAL cards */
static int
-sbs_setup(struct pci_dev *dev, struct pci_board *board,
+sbs_setup(struct serial_private *priv, struct pciserial_board *board,
struct uart_port *port, int idx)
{
unsigned int bar, offset = board->first_offset;
@@ -323,7 +298,7 @@
} else /* we have only 8 ports on PMC-OCTALPRO */
return 1;
- return setup_port(dev, port, bar, offset, board->reg_shift);
+ return setup_port(priv, port, bar, offset, board->reg_shift);
}
/*
@@ -389,6 +364,9 @@
* - 10x cards have control registers in IO and/or memory space;
* - 20x cards have control registers in standard PCI configuration space.
*
+ * Note: all 10x cards have PCI device ids 0x10..
+ * all 20x cards have PCI device ids 0x20..
+ *
* There are also Quartet Serial cards which use Oxford Semiconductor
* 16954 quad UART PCI chip clocked by 18.432 MHz quartz.
*
@@ -445,24 +423,18 @@
return 0;
}
-int pci_siig10x_fn(struct pci_dev *dev, int enable)
+static int pci_siig_init(struct pci_dev *dev)
{
- int ret = 0;
- if (enable)
- ret = pci_siig10x_init(dev);
- return ret;
-}
+ unsigned int type = dev->device & 0xff00;
-int pci_siig20x_fn(struct pci_dev *dev, int enable)
-{
- int ret = 0;
- if (enable)
- ret = pci_siig20x_init(dev);
- return ret;
-}
+ if (type == 0x1000)
+ return pci_siig10x_init(dev);
+ else if (type == 0x2000)
+ return pci_siig20x_init(dev);
-EXPORT_SYMBOL(pci_siig10x_fn);
-EXPORT_SYMBOL(pci_siig20x_fn);
+ moan_device("Unknown SIIG card", dev);
+ return -ENODEV;
+}
/*
* Timedia has an explosion of boards, and to avoid the PCI table from
@@ -523,7 +495,7 @@
* Ugh, this is ugly as all hell --- TYT
*/
static int
-pci_timedia_setup(struct pci_dev *dev, struct pci_board *board,
+pci_timedia_setup(struct serial_private *priv, struct pciserial_board *board,
struct uart_port *port, int idx)
{
unsigned int bar = 0, offset = board->first_offset;
@@ -549,14 +521,15 @@
bar = idx - 2;
}
- return setup_port(dev, port, bar, offset, board->reg_shift);
+ return setup_port(priv, port, bar, offset, board->reg_shift);
}
/*
* Some Titan cards are also a little weird
*/
static int
-titan_400l_800l_setup(struct pci_dev *dev, struct pci_board *board,
+titan_400l_800l_setup(struct serial_private *priv,
+ struct pciserial_board *board,
struct uart_port *port, int idx)
{
unsigned int bar, offset = board->first_offset;
@@ -573,7 +546,7 @@
offset = (idx - 2) * board->uart_offset;
}
- return setup_port(dev, port, bar, offset, board->reg_shift);
+ return setup_port(priv, port, bar, offset, board->reg_shift);
}
static int __devinit pci_xircom_init(struct pci_dev *dev)
@@ -593,7 +566,7 @@
}
static int
-pci_default_setup(struct pci_dev *dev, struct pci_board *board,
+pci_default_setup(struct serial_private *priv, struct pciserial_board *board,
struct uart_port *port, int idx)
{
unsigned int bar, offset = board->first_offset, maxnr;
@@ -604,13 +577,13 @@
else
offset += idx * board->uart_offset;
- maxnr = (pci_resource_len(dev, bar) - board->first_offset) /
+ maxnr = (pci_resource_len(priv->dev, bar) - board->first_offset) /
(8 << board->reg_shift);
if (board->flags & FL_REGION_SZ_CAP && idx >= maxnr)
return 1;
- return setup_port(dev, port, bar, offset, board->reg_shift);
+ return setup_port(priv, port, bar, offset, board->reg_shift);
}
/* This should be in linux/pci_ids.h */
@@ -754,152 +727,15 @@
.setup = sbs_setup,
.exit = __devexit_p(sbs_exit),
},
-
/*
* SIIG cards.
- * It is not clear whether these could be collapsed.
*/
{
.vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_1S_10x_550,
+ .device = PCI_ANY_ID,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
- .init = pci_siig10x_init,
- .setup = pci_default_setup,
- },
- {
- .vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_1S_10x_650,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .init = pci_siig10x_init,
- .setup = pci_default_setup,
- },
- {
- .vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_1S_10x_850,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .init = pci_siig10x_init,
- .setup = pci_default_setup,
- },
- {
- .vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_2S_10x_550,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .init = pci_siig10x_init,
- .setup = pci_default_setup,
- },
- {
- .vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_2S_10x_650,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .init = pci_siig10x_init,
- .setup = pci_default_setup,
- },
- {
- .vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_2S_10x_850,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .init = pci_siig10x_init,
- .setup = pci_default_setup,
- },
- {
- .vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_4S_10x_550,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .init = pci_siig10x_init,
- .setup = pci_default_setup,
- },
- {
- .vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_4S_10x_650,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .init = pci_siig10x_init,
- .setup = pci_default_setup,
- },
- {
- .vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_4S_10x_850,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .init = pci_siig10x_init,
- .setup = pci_default_setup,
- },
- {
- .vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_1S_20x_550,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .init = pci_siig20x_init,
- .setup = pci_default_setup,
- },
- {
- .vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_1S_20x_650,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .init = pci_siig20x_init,
- .setup = pci_default_setup,
- },
- {
- .vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_1S_20x_850,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .init = pci_siig20x_init,
- .setup = pci_default_setup,
- },
- {
- .vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_2S_20x_550,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .init = pci_siig20x_init,
- .setup = pci_default_setup,
- },
- { .vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_2S_20x_650,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .init = pci_siig20x_init,
- .setup = pci_default_setup,
- },
- {
- .vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_2S_20x_850,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .init = pci_siig20x_init,
- .setup = pci_default_setup,
- },
- {
- .vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_4S_20x_550,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .init = pci_siig20x_init,
- .setup = pci_default_setup,
- },
- {
- .vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_4S_20x_650,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .init = pci_siig20x_init,
- .setup = pci_default_setup,
- },
- {
- .vendor = PCI_VENDOR_ID_SIIG,
- .device = PCI_DEVICE_ID_SIIG_4S_20x_850,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .init = pci_siig20x_init,
+ .init = pci_siig_init,
.setup = pci_default_setup,
},
/*
@@ -990,7 +826,7 @@
}
static _INLINE_ int
-get_pci_irq(struct pci_dev *dev, struct pci_board *board, int idx)
+get_pci_irq(struct pci_dev *dev, struct pciserial_board *board)
{
if (board->flags & FL_NOIRQ)
return 0;
@@ -1115,7 +951,7 @@
* see first lines of serial_in() and serial_out() in 8250.c
*/
-static struct pci_board pci_boards[] __devinitdata = {
+static struct pciserial_board pci_boards[] __devinitdata = {
[pbn_default] = {
.flags = FL_BASE0,
.num_ports = 1,
@@ -1575,7 +1411,7 @@
* serial specs. Returns 0 on success, 1 on failure.
*/
static int __devinit
-serial_pci_guess_board(struct pci_dev *dev, struct pci_board *board)
+serial_pci_guess_board(struct pci_dev *dev, struct pciserial_board *board)
{
int num_iomem, num_port, first_port = -1, i;
@@ -1640,7 +1476,8 @@
}
static inline int
-serial_pci_matches(struct pci_board *board, struct pci_board *guessed)
+serial_pci_matches(struct pciserial_board *board,
+ struct pciserial_board *guessed)
{
return
board->num_ports == guessed->num_ports &&
@@ -1650,6 +1487,137 @@
board->first_offset == guessed->first_offset;
}
+struct serial_private *
+pciserial_init_ports(struct pci_dev *dev, struct pciserial_board *board)
+{
+ struct uart_port serial_port;
+ struct serial_private *priv;
+ struct pci_serial_quirk *quirk;
+ int rc, nr_ports, i;
+
+ nr_ports = board->num_ports;
+
+ /*
+ * Find an init and setup quirks.
+ */
+ quirk = find_quirk(dev);
+
+ /*
+ * Run the new-style initialization function.
+ * The initialization function returns:
+ * <0 - error
+ * 0 - use board->num_ports
+ * >0 - number of ports
+ */
+ if (quirk->init) {
+ rc = quirk->init(dev);
+ if (rc < 0) {
+ priv = ERR_PTR(rc);
+ goto err_out;
+ }
+ if (rc)
+ nr_ports = rc;
+ }
+
+ priv = kmalloc(sizeof(struct serial_private) +
+ sizeof(unsigned int) * nr_ports,
+ GFP_KERNEL);
+ if (!priv) {
+ priv = ERR_PTR(-ENOMEM);
+ goto err_deinit;
+ }
+
+ memset(priv, 0, sizeof(struct serial_private) +
+ sizeof(unsigned int) * nr_ports);
+
+ priv->dev = dev;
+ priv->quirk = quirk;
+
+ memset(&serial_port, 0, sizeof(struct uart_port));
+ serial_port.flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ;
+ serial_port.uartclk = board->base_baud * 16;
+ serial_port.irq = get_pci_irq(dev, board);
+ serial_port.dev = &dev->dev;
+
+ for (i = 0; i < nr_ports; i++) {
+ if (quirk->setup(priv, board, &serial_port, i))
+ break;
+
+#ifdef SERIAL_DEBUG_PCI
+ printk("Setup PCI port: port %x, irq %d, type %d\n",
+ serial_port.iobase, serial_port.irq, serial_port.iotype);
+#endif
+
+ priv->line[i] = serial8250_register_port(&serial_port);
+ if (priv->line[i] < 0) {
+ printk(KERN_WARNING "Couldn't register serial port %s: %d\n", pci_name(dev), priv->line[i]);
+ break;
+ }
+ }
+
+ priv->nr = i;
+
+ return priv;
+
+ err_deinit:
+ if (quirk->exit)
+ quirk->exit(dev);
+ err_out:
+ return priv;
+}
+EXPORT_SYMBOL_GPL(pciserial_init_ports);
+
+void pciserial_remove_ports(struct serial_private *priv)
+{
+ struct pci_serial_quirk *quirk;
+ int i;
+
+ for (i = 0; i < priv->nr; i++)
+ serial8250_unregister_port(priv->line[i]);
+
+ for (i = 0; i < PCI_NUM_BAR_RESOURCES; i++) {
+ if (priv->remapped_bar[i])
+ iounmap(priv->remapped_bar[i]);
+ priv->remapped_bar[i] = NULL;
+ }
+
+ /*
+ * Find the exit quirks.
+ */
+ quirk = find_quirk(priv->dev);
+ if (quirk->exit)
+ quirk->exit(priv->dev);
+
+ kfree(priv);
+}
+EXPORT_SYMBOL_GPL(pciserial_remove_ports);
+
+void pciserial_suspend_ports(struct serial_private *priv)
+{
+ int i;
+
+ for (i = 0; i < priv->nr; i++)
+ if (priv->line[i] >= 0)
+ serial8250_suspend_port(priv->line[i]);
+}
+EXPORT_SYMBOL_GPL(pciserial_suspend_ports);
+
+void pciserial_resume_ports(struct serial_private *priv)
+{
+ int i;
+
+ /*
+ * Ensure that the board is correctly configured.
+ */
+ if (priv->quirk->init)
+ priv->quirk->init(priv->dev);
+
+ for (i = 0; i < priv->nr; i++)
+ if (priv->line[i] >= 0)
+ serial8250_resume_port(priv->line[i]);
+}
+EXPORT_SYMBOL_GPL(pciserial_resume_ports);
+
/*
* Probe one serial board. Unfortunately, there is no rhyme nor reason
* to the arrangement of serial ports on a PCI card.
@@ -1658,9 +1626,8 @@
pciserial_init_one(struct pci_dev *dev, const struct pci_device_id *ent)
{
struct serial_private *priv;
- struct pci_board *board, tmp;
- struct pci_serial_quirk *quirk;
- int rc, nr_ports, i;
+ struct pciserial_board *board, tmp;
+ int rc;
if (ent->driver_data >= ARRAY_SIZE(pci_boards)) {
printk(KERN_ERR "pci_init_one: invalid driver_data: %ld\n",
@@ -1679,7 +1646,7 @@
* Use a copy of the pci_board entry for this;
* avoid changing entries in the table.
*/
- memcpy(&tmp, board, sizeof(struct pci_board));
+ memcpy(&tmp, board, sizeof(struct pciserial_board));
board = &tmp;
/*
@@ -1695,79 +1662,22 @@
* detect this boards settings with our heuristic,
* then we no longer need this entry.
*/
- memcpy(&tmp, &pci_boards[pbn_default], sizeof(struct pci_board));
+ memcpy(&tmp, &pci_boards[pbn_default],
+ sizeof(struct pciserial_board));
rc = serial_pci_guess_board(dev, &tmp);
if (rc == 0 && serial_pci_matches(board, &tmp))
moan_device("Redundant entry in serial pci_table.",
dev);
}
- nr_ports = board->num_ports;
-
- /*
- * Find an init and setup quirks.
- */
- quirk = find_quirk(dev);
-
- /*
- * Run the new-style initialization function.
- * The initialization function returns:
- * <0 - error
- * 0 - use board->num_ports
- * >0 - number of ports
- */
- if (quirk->init) {
- rc = quirk->init(dev);
- if (rc < 0)
- goto disable;
- if (rc)
- nr_ports = rc;
+ priv = pciserial_init_ports(dev, board);
+ if (!IS_ERR(priv)) {
+ pci_set_drvdata(dev, priv);
+ return 0;
}
- priv = kmalloc(sizeof(struct serial_private) +
- sizeof(unsigned int) * nr_ports,
- GFP_KERNEL);
- if (!priv) {
- rc = -ENOMEM;
- goto deinit;
- }
+ rc = PTR_ERR(priv);
- memset(priv, 0, sizeof(struct serial_private) +
- sizeof(unsigned int) * nr_ports);
-
- priv->quirk = quirk;
- pci_set_drvdata(dev, priv);
-
- for (i = 0; i < nr_ports; i++) {
- struct uart_port serial_port;
- memset(&serial_port, 0, sizeof(struct uart_port));
-
- serial_port.flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF |
- UPF_SHARE_IRQ;
- serial_port.uartclk = board->base_baud * 16;
- serial_port.irq = get_pci_irq(dev, board, i);
- serial_port.dev = &dev->dev;
- if (quirk->setup(dev, board, &serial_port, i))
- break;
-#ifdef SERIAL_DEBUG_PCI
- printk("Setup PCI port: port %x, irq %d, type %d\n",
- serial_port.iobase, serial_port.irq, serial_port.iotype);
-#endif
-
- priv->line[i] = serial8250_register_port(&serial_port);
- if (priv->line[i] < 0) {
- printk(KERN_WARNING "Couldn't register serial port %s: %d\n", pci_name(dev), priv->line[i]);
- break;
- }
- }
-
- priv->nr = i;
-
- return 0;
-
- deinit:
- if (quirk->exit)
- quirk->exit(dev);
disable:
pci_disable_device(dev);
return rc;
@@ -1776,42 +1686,21 @@
static void __devexit pciserial_remove_one(struct pci_dev *dev)
{
struct serial_private *priv = pci_get_drvdata(dev);
- struct pci_serial_quirk *quirk;
- int i;
pci_set_drvdata(dev, NULL);
- for (i = 0; i < priv->nr; i++)
- serial8250_unregister_port(priv->line[i]);
-
- for (i = 0; i < PCI_NUM_BAR_RESOURCES; i++) {
- if (priv->remapped_bar[i])
- iounmap(priv->remapped_bar[i]);
- priv->remapped_bar[i] = NULL;
- }
-
- /*
- * Find the exit quirks.
- */
- quirk = find_quirk(dev);
- if (quirk->exit)
- quirk->exit(dev);
+ pciserial_remove_ports(priv);
pci_disable_device(dev);
-
- kfree(priv);
}
static int pciserial_suspend_one(struct pci_dev *dev, pm_message_t state)
{
struct serial_private *priv = pci_get_drvdata(dev);
- if (priv) {
- int i;
+ if (priv)
+ pciserial_suspend_ports(priv);
- for (i = 0; i < priv->nr; i++)
- serial8250_suspend_port(priv->line[i]);
- }
pci_save_state(dev);
pci_set_power_state(dev, pci_choose_state(dev, state));
return 0;
@@ -1825,21 +1714,12 @@
pci_restore_state(dev);
if (priv) {
- int i;
-
/*
* The device may have been disabled. Re-enable it.
*/
pci_enable_device(dev);
- /*
- * Ensure that the board is correctly configured.
- */
- if (priv->quirk->init)
- priv->quirk->init(dev);
-
- for (i = 0; i < priv->nr; i++)
- serial8250_resume_port(priv->line[i]);
+ pciserial_resume_ports(priv);
}
return 0;
}
diff --git a/fs/adfs/adfs.h b/fs/adfs/adfs.h
index 63f5df9..fd52843 100644
--- a/fs/adfs/adfs.h
+++ b/fs/adfs/adfs.h
@@ -97,7 +97,7 @@
extern struct inode_operations adfs_file_inode_operations;
extern struct file_operations adfs_file_operations;
-extern inline __u32 signed_asl(__u32 val, signed int shift)
+static inline __u32 signed_asl(__u32 val, signed int shift)
{
if (shift >= 0)
val <<= shift;
@@ -112,7 +112,7 @@
*
* The root directory ID should always be looked up in the map [3.4]
*/
-extern inline int
+static inline int
__adfs_block_map(struct super_block *sb, unsigned int object_id,
unsigned int block)
{
diff --git a/fs/sysfs/inode.c b/fs/sysfs/inode.c
index d727dc9..970a33f 100644
--- a/fs/sysfs/inode.c
+++ b/fs/sysfs/inode.c
@@ -228,6 +228,10 @@
struct sysfs_dirent * sd;
struct sysfs_dirent * parent_sd = dir->d_fsdata;
+ if (dir->d_inode == NULL)
+ /* no inode means this hasn't been made visible yet */
+ return;
+
down(&dir->d_inode->i_sem);
list_for_each_entry(sd, &parent_sd->s_children, s_sibling) {
if (!sd->s_element)
diff --git a/include/asm-arm/arch-sa1100/mcp.h b/include/asm-arm/arch-sa1100/mcp.h
new file mode 100644
index 0000000..f58a227
--- /dev/null
+++ b/include/asm-arm/arch-sa1100/mcp.h
@@ -0,0 +1,21 @@
+/*
+ * linux/include/asm-arm/arch-sa1100/mcp.h
+ *
+ * Copyright (C) 2005 Russell King.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef __ASM_ARM_ARCH_MCP_H
+#define __ASM_ARM_ARCH_MCP_H
+
+#include <linux/types.h>
+
+struct mcp_plat_data {
+ u32 mccr0;
+ u32 mccr1;
+ unsigned int sclk_rate;
+};
+
+#endif
diff --git a/include/asm-arm/hardware/gic.h b/include/asm-arm/hardware/gic.h
new file mode 100644
index 0000000..3fa5eb7
--- /dev/null
+++ b/include/asm-arm/hardware/gic.h
@@ -0,0 +1,41 @@
+/*
+ * linux/include/asm-arm/hardware/gic.h
+ *
+ * Copyright (C) 2002 ARM Limited, All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef __ASM_ARM_HARDWARE_GIC_H
+#define __ASM_ARM_HARDWARE_GIC_H
+
+#include <linux/compiler.h>
+
+#define GIC_CPU_CTRL 0x00
+#define GIC_CPU_PRIMASK 0x04
+#define GIC_CPU_BINPOINT 0x08
+#define GIC_CPU_INTACK 0x0c
+#define GIC_CPU_EOI 0x10
+#define GIC_CPU_RUNNINGPRI 0x14
+#define GIC_CPU_HIGHPRI 0x18
+
+#define GIC_DIST_CTRL 0x000
+#define GIC_DIST_CTR 0x004
+#define GIC_DIST_ENABLE_SET 0x100
+#define GIC_DIST_ENABLE_CLEAR 0x180
+#define GIC_DIST_PENDING_SET 0x200
+#define GIC_DIST_PENDING_CLEAR 0x280
+#define GIC_DIST_ACTIVE_BIT 0x300
+#define GIC_DIST_PRI 0x400
+#define GIC_DIST_TARGET 0x800
+#define GIC_DIST_CONFIG 0xc00
+#define GIC_DIST_SOFTINT 0xf00
+
+#ifndef __ASSEMBLY__
+void gic_dist_init(void __iomem *base);
+void gic_cpu_init(void __iomem *base);
+void gic_raise_softirq(cpumask_t cpumask, unsigned int irq);
+#endif
+
+#endif
diff --git a/include/asm-ppc64/bug.h b/include/asm-ppc64/bug.h
index 169868f..1601782 100644
--- a/include/asm-ppc64/bug.h
+++ b/include/asm-ppc64/bug.h
@@ -43,8 +43,8 @@
".section __bug_table,\"a\"\n\t" \
" .llong 1b,%1,%2,%3\n" \
".previous" \
- : : "r" (x), "i" (__LINE__), "i" (__FILE__), \
- "i" (__FUNCTION__)); \
+ : : "r" ((long long)(x)), "i" (__LINE__), \
+ "i" (__FILE__), "i" (__FUNCTION__)); \
} while (0)
#define WARN_ON(x) do { \
@@ -53,7 +53,8 @@
".section __bug_table,\"a\"\n\t" \
" .llong 1b,%1,%2,%3\n" \
".previous" \
- : : "r" (x), "i" (__LINE__ + BUG_WARNING_TRAP), \
+ : : "r" ((long long)(x)), \
+ "i" (__LINE__ + BUG_WARNING_TRAP), \
"i" (__FILE__), "i" (__FUNCTION__)); \
} while (0)
diff --git a/include/asm-x86_64/e820.h b/include/asm-x86_64/e820.h
index 8e94edf..e682edc 100644
--- a/include/asm-x86_64/e820.h
+++ b/include/asm-x86_64/e820.h
@@ -51,6 +51,8 @@
extern void e820_bootmem_free(pg_data_t *pgdat, unsigned long start,unsigned long end);
extern void e820_setup_gap(void);
+extern unsigned long e820_hole_size(unsigned long start_pfn,
+ unsigned long end_pfn);
extern void __init parse_memopt(char *p, char **end);
diff --git a/include/linux/8250_pci.h b/include/linux/8250_pci.h
index 5f3ab21..3209dd4 100644
--- a/include/linux/8250_pci.h
+++ b/include/linux/8250_pci.h
@@ -1,2 +1,37 @@
-int pci_siig10x_fn(struct pci_dev *dev, int enable);
-int pci_siig20x_fn(struct pci_dev *dev, int enable);
+/*
+ * Definitions for PCI support.
+ */
+#define FL_BASE_MASK 0x0007
+#define FL_BASE0 0x0000
+#define FL_BASE1 0x0001
+#define FL_BASE2 0x0002
+#define FL_BASE3 0x0003
+#define FL_BASE4 0x0004
+#define FL_GET_BASE(x) (x & FL_BASE_MASK)
+
+/* Use successive BARs (PCI base address registers),
+ else use offset into some specified BAR */
+#define FL_BASE_BARS 0x0008
+
+/* do not assign an irq */
+#define FL_NOIRQ 0x0080
+
+/* Use the Base address register size to cap number of ports */
+#define FL_REGION_SZ_CAP 0x0100
+
+struct pciserial_board {
+ unsigned int flags;
+ unsigned int num_ports;
+ unsigned int base_baud;
+ unsigned int uart_offset;
+ unsigned int reg_shift;
+ unsigned int first_offset;
+};
+
+struct serial_private;
+
+struct serial_private *
+pciserial_init_ports(struct pci_dev *dev, struct pciserial_board *board);
+void pciserial_remove_ports(struct serial_private *priv);
+void pciserial_suspend_ports(struct serial_private *priv);
+void pciserial_resume_ports(struct serial_private *priv);
diff --git a/include/linux/ata.h b/include/linux/ata.h
index ca5fcad..9d25e98 100644
--- a/include/linux/ata.h
+++ b/include/linux/ata.h
@@ -108,6 +108,8 @@
/* ATA device commands */
ATA_CMD_CHK_POWER = 0xE5, /* check power mode */
+ ATA_CMD_STANDBY = 0xE2, /* place in standby power mode */
+ ATA_CMD_IDLE = 0xE3, /* place in idle power mode */
ATA_CMD_EDD = 0x90, /* execute device diagnostic */
ATA_CMD_FLUSH = 0xE7,
ATA_CMD_FLUSH_EXT = 0xEA,
diff --git a/include/linux/ethtool.h b/include/linux/ethtool.h
index a0ab26a..d7021c3 100644
--- a/include/linux/ethtool.h
+++ b/include/linux/ethtool.h
@@ -408,6 +408,8 @@
#define SUPPORTED_FIBRE (1 << 10)
#define SUPPORTED_BNC (1 << 11)
#define SUPPORTED_10000baseT_Full (1 << 12)
+#define SUPPORTED_Pause (1 << 13)
+#define SUPPORTED_Asym_Pause (1 << 14)
/* Indicates what features are advertised by the interface. */
#define ADVERTISED_10baseT_Half (1 << 0)
@@ -423,6 +425,8 @@
#define ADVERTISED_FIBRE (1 << 10)
#define ADVERTISED_BNC (1 << 11)
#define ADVERTISED_10000baseT_Full (1 << 12)
+#define ADVERTISED_Pause (1 << 13)
+#define ADVERTISED_Asym_Pause (1 << 14)
/* The following are all involved in forcing a particular link
* mode for the device for setting things. When getting the
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 6cd9ba6..7c09540 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -113,6 +113,8 @@
ATA_FLAG_MMIO = (1 << 6), /* use MMIO, not PIO */
ATA_FLAG_SATA_RESET = (1 << 7), /* use COMRESET */
ATA_FLAG_PIO_DMA = (1 << 8), /* PIO cmds via DMA */
+ ATA_FLAG_NOINTR = (1 << 9), /* FIXME: Remove this once
+ * proper HSM is in place. */
ATA_QCFLAG_ACTIVE = (1 << 1), /* cmd not yet ack'd to scsi lyer */
ATA_QCFLAG_SG = (1 << 3), /* have s/g table? */
@@ -363,7 +365,7 @@
void (*host_stop) (struct ata_host_set *host_set);
- void (*bmdma_stop) (struct ata_port *ap);
+ void (*bmdma_stop) (struct ata_queued_cmd *qc);
u8 (*bmdma_status) (struct ata_port *ap);
};
@@ -424,7 +426,7 @@
extern void ata_dev_config(struct ata_port *ap, unsigned int i);
extern void ata_bmdma_setup (struct ata_queued_cmd *qc);
extern void ata_bmdma_start (struct ata_queued_cmd *qc);
-extern void ata_bmdma_stop(struct ata_port *ap);
+extern void ata_bmdma_stop(struct ata_queued_cmd *qc);
extern u8 ata_bmdma_status(struct ata_port *ap);
extern void ata_bmdma_irq_clear(struct ata_port *ap);
extern void ata_qc_complete(struct ata_queued_cmd *qc, u8 drv_stat);
@@ -644,7 +646,7 @@
ap->ops->scr_write(ap, reg, val);
}
-static inline void scr_write_flush(struct ata_port *ap, unsigned int reg,
+static inline void scr_write_flush(struct ata_port *ap, unsigned int reg,
u32 val)
{
ap->ops->scr_write(ap, reg, val);
diff --git a/include/linux/mii.h b/include/linux/mii.h
index 374b615..9b8d047 100644
--- a/include/linux/mii.h
+++ b/include/linux/mii.h
@@ -22,6 +22,7 @@
#define MII_EXPANSION 0x06 /* Expansion register */
#define MII_CTRL1000 0x09 /* 1000BASE-T control */
#define MII_STAT1000 0x0a /* 1000BASE-T status */
+#define MII_ESTATUS 0x0f /* Extended Status */
#define MII_DCOUNTER 0x12 /* Disconnect counter */
#define MII_FCSCOUNTER 0x13 /* False carrier counter */
#define MII_NWAYTEST 0x14 /* N-way auto-neg test reg */
@@ -54,7 +55,10 @@
#define BMSR_ANEGCAPABLE 0x0008 /* Able to do auto-negotiation */
#define BMSR_RFAULT 0x0010 /* Remote fault detected */
#define BMSR_ANEGCOMPLETE 0x0020 /* Auto-negotiation complete */
-#define BMSR_RESV 0x07c0 /* Unused... */
+#define BMSR_RESV 0x00c0 /* Unused... */
+#define BMSR_ESTATEN 0x0100 /* Extended Status in R15 */
+#define BMSR_100FULL2 0x0200 /* Can do 100BASE-T2 HDX */
+#define BMSR_100HALF2 0x0400 /* Can do 100BASE-T2 FDX */
#define BMSR_10HALF 0x0800 /* Can do 10mbps, half-duplex */
#define BMSR_10FULL 0x1000 /* Can do 10mbps, full-duplex */
#define BMSR_100HALF 0x2000 /* Can do 100mbps, half-duplex */
@@ -114,6 +118,9 @@
#define EXPANSION_MFAULTS 0x0010 /* Multiple faults detected */
#define EXPANSION_RESV 0xffe0 /* Unused... */
+#define ESTATUS_1000_TFULL 0x2000 /* Can do 1000BT Full */
+#define ESTATUS_1000_THALF 0x1000 /* Can do 1000BT Half */
+
/* N-way test register. */
#define NWAYTEST_RESV1 0x00ff /* Unused... */
#define NWAYTEST_LOOPBACK 0x0100 /* Enable loopback for N-way */
diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h
index f90f674..9a0893f 100644
--- a/include/linux/mmc/host.h
+++ b/include/linux/mmc/host.h
@@ -63,11 +63,12 @@
struct mmc_host {
struct device *dev;
+ struct class_device class_dev;
+ int index;
struct mmc_host_ops *ops;
unsigned int f_min;
unsigned int f_max;
u32 ocr_avail;
- char host_name[8];
/* host specific block data */
unsigned int max_seg_size; /* see blk_queue_max_segment_size */
@@ -97,6 +98,7 @@
#define mmc_priv(x) ((void *)((x) + 1))
#define mmc_dev(x) ((x)->dev)
+#define mmc_hostname(x) ((x)->class_dev.class_id)
extern int mmc_suspend_host(struct mmc_host *, pm_message_t);
extern int mmc_resume_host(struct mmc_host *);
diff --git a/include/linux/mod_devicetable.h b/include/linux/mod_devicetable.h
index dce53ac..97bbccd 100644
--- a/include/linux/mod_devicetable.h
+++ b/include/linux/mod_devicetable.h
@@ -33,7 +33,8 @@
__u32 model_id;
__u32 specifier_id;
__u32 version;
- kernel_ulong_t driver_data;
+ kernel_ulong_t driver_data
+ __attribute__((aligned(sizeof(kernel_ulong_t))));
};
@@ -182,7 +183,11 @@
char name[32];
char type[32];
char compatible[128];
+#if __KERNEL__
void *data;
+#else
+ kernel_ulong_t data;
+#endif
};
@@ -208,7 +213,8 @@
#ifdef __KERNEL__
const char * prod_id[4];
#else
- kernel_ulong_t prod_id[4];
+ kernel_ulong_t prod_id[4]
+ __attribute__((aligned(sizeof(kernel_ulong_t))));
#endif
/* not matched against */
diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h
index 927ed48..499a532 100644
--- a/include/linux/pci_ids.h
+++ b/include/linux/pci_ids.h
@@ -1249,6 +1249,7 @@
#define PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_SATA 0x0266
#define PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_SATA2 0x0267
#define PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_IDE 0x036E
+#define PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_SATA 0x036F
#define PCI_DEVICE_ID_NVIDIA_NVENET_12 0x0268
#define PCI_DEVICE_ID_NVIDIA_NVENET_13 0x0269
#define PCI_DEVICE_ID_NVIDIA_MCP51_AUDIO 0x026B
diff --git a/include/linux/phy.h b/include/linux/phy.h
new file mode 100644
index 0000000..72cb67b
--- /dev/null
+++ b/include/linux/phy.h
@@ -0,0 +1,377 @@
+/*
+ * include/linux/phy.h
+ *
+ * Framework and drivers for configuring and reading different PHYs
+ * Based on code in sungem_phy.c and gianfar_phy.c
+ *
+ * Author: Andy Fleming
+ *
+ * Copyright (c) 2004 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+
+#ifndef __PHY_H
+#define __PHY_H
+
+#include <linux/spinlock.h>
+#include <linux/device.h>
+
+#define PHY_BASIC_FEATURES (SUPPORTED_10baseT_Half | \
+ SUPPORTED_10baseT_Full | \
+ SUPPORTED_100baseT_Half | \
+ SUPPORTED_100baseT_Full | \
+ SUPPORTED_Autoneg | \
+ SUPPORTED_TP | \
+ SUPPORTED_MII)
+
+#define PHY_GBIT_FEATURES (PHY_BASIC_FEATURES | \
+ SUPPORTED_1000baseT_Half | \
+ SUPPORTED_1000baseT_Full)
+
+/* Set phydev->irq to PHY_POLL if interrupts are not supported,
+ * or not desired for this PHY. Set to PHY_IGNORE_INTERRUPT if
+ * the attached driver handles the interrupt
+ */
+#define PHY_POLL -1
+#define PHY_IGNORE_INTERRUPT -2
+
+#define PHY_HAS_INTERRUPT 0x00000001
+#define PHY_HAS_MAGICANEG 0x00000002
+
+#define MII_BUS_MAX 4
+
+
+#define PHY_INIT_TIMEOUT 100000
+#define PHY_STATE_TIME 1
+#define PHY_FORCE_TIMEOUT 10
+#define PHY_AN_TIMEOUT 10
+
+#define PHY_MAX_ADDR 32
+
+/* The Bus class for PHYs. Devices which provide access to
+ * PHYs should register using this structure */
+struct mii_bus {
+ const char *name;
+ int id;
+ void *priv;
+ int (*read)(struct mii_bus *bus, int phy_id, int regnum);
+ int (*write)(struct mii_bus *bus, int phy_id, int regnum, u16 val);
+ int (*reset)(struct mii_bus *bus);
+
+ /* A lock to ensure that only one thing can read/write
+ * the MDIO bus at a time */
+ spinlock_t mdio_lock;
+
+ struct device *dev;
+
+ /* list of all PHYs on bus */
+ struct phy_device *phy_map[PHY_MAX_ADDR];
+
+ /* Pointer to an array of interrupts, each PHY's
+ * interrupt at the index matching its address */
+ int *irq;
+};
+
+#define PHY_INTERRUPT_DISABLED 0x0
+#define PHY_INTERRUPT_ENABLED 0x80000000
+
+/* PHY state machine states:
+ *
+ * DOWN: PHY device and driver are not ready for anything. probe
+ * should be called if and only if the PHY is in this state,
+ * given that the PHY device exists.
+ * - PHY driver probe function will, depending on the PHY, set
+ * the state to STARTING or READY
+ *
+ * STARTING: PHY device is coming up, and the ethernet driver is
+ * not ready. PHY drivers may set this in the probe function.
+ * If they do, they are responsible for making sure the state is
+ * eventually set to indicate whether the PHY is UP or READY,
+ * depending on the state when the PHY is done starting up.
+ * - PHY driver will set the state to READY
+ * - start will set the state to PENDING
+ *
+ * READY: PHY is ready to send and receive packets, but the
+ * controller is not. By default, PHYs which do not implement
+ * probe will be set to this state by phy_probe(). If the PHY
+ * driver knows the PHY is ready, and the PHY state is STARTING,
+ * then it sets this STATE.
+ * - start will set the state to UP
+ *
+ * PENDING: PHY device is coming up, but the ethernet driver is
+ * ready. phy_start will set this state if the PHY state is
+ * STARTING.
+ * - PHY driver will set the state to UP when the PHY is ready
+ *
+ * UP: The PHY and attached device are ready to do work.
+ * Interrupts should be started here.
+ * - timer moves to AN
+ *
+ * AN: The PHY is currently negotiating the link state. Link is
+ * therefore down for now. phy_timer will set this state when it
+ * detects the state is UP. config_aneg will set this state
+ * whenever called with phydev->autoneg set to AUTONEG_ENABLE.
+ * - If autonegotiation finishes, but there's no link, it sets
+ * the state to NOLINK.
+ * - If aneg finishes with link, it sets the state to RUNNING,
+ * and calls adjust_link
+ * - If autonegotiation did not finish after an arbitrary amount
+ * of time, autonegotiation should be tried again if the PHY
+ * supports "magic" autonegotiation (back to AN)
+ * - If it didn't finish, and no magic_aneg, move to FORCING.
+ *
+ * NOLINK: PHY is up, but not currently plugged in.
+ * - If the timer notes that the link comes back, we move to RUNNING
+ * - config_aneg moves to AN
+ * - phy_stop moves to HALTED
+ *
+ * FORCING: PHY is being configured with forced settings
+ * - if link is up, move to RUNNING
+ * - If link is down, we drop to the next highest setting, and
+ * retry (FORCING) after a timeout
+ * - phy_stop moves to HALTED
+ *
+ * RUNNING: PHY is currently up, running, and possibly sending
+ * and/or receiving packets
+ * - timer will set CHANGELINK if we're polling (this ensures the
+ * link state is polled every other cycle of this state machine,
+ * which makes it every other second)
+ * - irq will set CHANGELINK
+ * - config_aneg will set AN
+ * - phy_stop moves to HALTED
+ *
+ * CHANGELINK: PHY experienced a change in link state
+ * - timer moves to RUNNING if link
+ * - timer moves to NOLINK if the link is down
+ * - phy_stop moves to HALTED
+ *
+ * HALTED: PHY is up, but no polling or interrupts are done. Or
+ * PHY is in an error state.
+ *
+ * - phy_start moves to RESUMING
+ *
+ * RESUMING: PHY was halted, but now wants to run again.
+ * - If we are forcing, or aneg is done, timer moves to RUNNING
+ * - If aneg is not done, timer moves to AN
+ * - phy_stop moves to HALTED
+ */
+enum phy_state {
+ PHY_DOWN=0,
+ PHY_STARTING,
+ PHY_READY,
+ PHY_PENDING,
+ PHY_UP,
+ PHY_AN,
+ PHY_RUNNING,
+ PHY_NOLINK,
+ PHY_FORCING,
+ PHY_CHANGELINK,
+ PHY_HALTED,
+ PHY_RESUMING
+};
+
+/* phy_device: An instance of a PHY
+ *
+ * drv: Pointer to the driver for this PHY instance
+ * bus: Pointer to the bus this PHY is on
+ * dev: driver model device structure for this PHY
+ * phy_id: UID for this device found during discovery
+ * state: state of the PHY for management purposes
+ * dev_flags: Device-specific flags used by the PHY driver.
+ * addr: Bus address of PHY
+ * link_timeout: The number of timer firings to wait before the
+ * giving up on the current attempt at acquiring a link
+ * irq: IRQ number of the PHY's interrupt (-1 if none)
+ * phy_timer: The timer for handling the state machine
+ * phy_queue: A work_queue for the interrupt
+ * attached_dev: The attached enet driver's device instance ptr
+ * adjust_link: Callback for the enet controller to respond to
+ * changes in the link state.
+ * adjust_state: Callback for the enet driver to respond to
+ * changes in the state machine.
+ *
+ * speed, duplex, pause, supported, advertising, and
+ * autoneg are used like in mii_if_info
+ *
+ * interrupts currently only supports enabled or disabled,
+ * but could be changed in the future to support enabling
+ * and disabling specific interrupts
+ *
+ * Contains some infrastructure for polling and interrupt
+ * handling, as well as handling shifts in PHY hardware state
+ */
+struct phy_device {
+ /* Information about the PHY type */
+ /* And management functions */
+ struct phy_driver *drv;
+
+ struct mii_bus *bus;
+
+ struct device dev;
+
+ u32 phy_id;
+
+ enum phy_state state;
+
+ u32 dev_flags;
+
+ /* Bus address of the PHY (0-32) */
+ int addr;
+
+ /* forced speed & duplex (no autoneg)
+ * partner speed & duplex & pause (autoneg)
+ */
+ int speed;
+ int duplex;
+ int pause;
+ int asym_pause;
+
+ /* The most recently read link state */
+ int link;
+
+ /* Enabled Interrupts */
+ u32 interrupts;
+
+ /* Union of PHY and Attached devices' supported modes */
+ /* See mii.h for more info */
+ u32 supported;
+ u32 advertising;
+
+ int autoneg;
+
+ int link_timeout;
+
+ /* Interrupt number for this PHY
+ * -1 means no interrupt */
+ int irq;
+
+ /* private data pointer */
+ /* For use by PHYs to maintain extra state */
+ void *priv;
+
+ /* Interrupt and Polling infrastructure */
+ struct work_struct phy_queue;
+ struct timer_list phy_timer;
+
+ spinlock_t lock;
+
+ struct net_device *attached_dev;
+
+ void (*adjust_link)(struct net_device *dev);
+
+ void (*adjust_state)(struct net_device *dev);
+};
+#define to_phy_device(d) container_of(d, struct phy_device, dev)
+
+/* struct phy_driver: Driver structure for a particular PHY type
+ *
+ * phy_id: The result of reading the UID registers of this PHY
+ * type, and ANDing them with the phy_id_mask. This driver
+ * only works for PHYs with IDs which match this field
+ * name: The friendly name of this PHY type
+ * phy_id_mask: Defines the important bits of the phy_id
+ * features: A list of features (speed, duplex, etc) supported
+ * by this PHY
+ * flags: A bitfield defining certain other features this PHY
+ * supports (like interrupts)
+ *
+ * The drivers must implement config_aneg and read_status. All
+ * other functions are optional. Note that none of these
+ * functions should be called from interrupt time. The goal is
+ * for the bus read/write functions to be able to block when the
+ * bus transaction is happening, and be freed up by an interrupt
+ * (The MPC85xx has this ability, though it is not currently
+ * supported in the driver).
+ */
+struct phy_driver {
+ u32 phy_id;
+ char *name;
+ unsigned int phy_id_mask;
+ u32 features;
+ u32 flags;
+
+ /* Called to initialize the PHY,
+ * including after a reset */
+ int (*config_init)(struct phy_device *phydev);
+
+ /* Called during discovery. Used to set
+ * up device-specific structures, if any */
+ int (*probe)(struct phy_device *phydev);
+
+ /* PHY Power Management */
+ int (*suspend)(struct phy_device *phydev);
+ int (*resume)(struct phy_device *phydev);
+
+ /* Configures the advertisement and resets
+ * autonegotiation if phydev->autoneg is on,
+ * forces the speed to the current settings in phydev
+ * if phydev->autoneg is off */
+ int (*config_aneg)(struct phy_device *phydev);
+
+ /* Determines the negotiated speed and duplex */
+ int (*read_status)(struct phy_device *phydev);
+
+ /* Clears any pending interrupts */
+ int (*ack_interrupt)(struct phy_device *phydev);
+
+ /* Enables or disables interrupts */
+ int (*config_intr)(struct phy_device *phydev);
+
+ /* Clears up any memory if needed */
+ void (*remove)(struct phy_device *phydev);
+
+ struct device_driver driver;
+};
+#define to_phy_driver(d) container_of(d, struct phy_driver, driver)
+
+int phy_read(struct phy_device *phydev, u16 regnum);
+int phy_write(struct phy_device *phydev, u16 regnum, u16 val);
+struct phy_device* get_phy_device(struct mii_bus *bus, int addr);
+int phy_clear_interrupt(struct phy_device *phydev);
+int phy_config_interrupt(struct phy_device *phydev, u32 interrupts);
+struct phy_device * phy_attach(struct net_device *dev,
+ const char *phy_id, u32 flags);
+struct phy_device * phy_connect(struct net_device *dev, const char *phy_id,
+ void (*handler)(struct net_device *), u32 flags);
+void phy_disconnect(struct phy_device *phydev);
+void phy_detach(struct phy_device *phydev);
+void phy_start(struct phy_device *phydev);
+void phy_stop(struct phy_device *phydev);
+int phy_start_aneg(struct phy_device *phydev);
+
+int mdiobus_register(struct mii_bus *bus);
+void mdiobus_unregister(struct mii_bus *bus);
+void phy_sanitize_settings(struct phy_device *phydev);
+int phy_stop_interrupts(struct phy_device *phydev);
+
+static inline int phy_read_status(struct phy_device *phydev) {
+ return phydev->drv->read_status(phydev);
+}
+
+int genphy_config_advert(struct phy_device *phydev);
+int genphy_setup_forced(struct phy_device *phydev);
+int genphy_restart_aneg(struct phy_device *phydev);
+int genphy_config_aneg(struct phy_device *phydev);
+int genphy_update_link(struct phy_device *phydev);
+int genphy_read_status(struct phy_device *phydev);
+void phy_driver_unregister(struct phy_driver *drv);
+int phy_driver_register(struct phy_driver *new_driver);
+void phy_prepare_link(struct phy_device *phydev,
+ void (*adjust_link)(struct net_device *));
+void phy_start_machine(struct phy_device *phydev,
+ void (*handler)(struct net_device *));
+void phy_stop_machine(struct phy_device *phydev);
+int phy_ethtool_sset(struct phy_device *phydev, struct ethtool_cmd *cmd);
+int phy_ethtool_gset(struct phy_device *phydev, struct ethtool_cmd *cmd);
+int phy_mii_ioctl(struct phy_device *phydev,
+ struct mii_ioctl_data *mii_data, int cmd);
+int phy_start_interrupts(struct phy_device *phydev);
+void phy_print_status(struct phy_device *phydev);
+
+extern struct bus_type mdio_bus_type;
+#endif /* __PHY_H */
diff --git a/include/linux/serialP.h b/include/linux/serialP.h
index 2b2f35a..2b9e6b9 100644
--- a/include/linux/serialP.h
+++ b/include/linux/serialP.h
@@ -140,44 +140,4 @@
#define ALPHA_KLUDGE_MCR 0
#endif
-/*
- * Definitions for PCI support.
- */
-#define SPCI_FL_BASE_MASK 0x0007
-#define SPCI_FL_BASE0 0x0000
-#define SPCI_FL_BASE1 0x0001
-#define SPCI_FL_BASE2 0x0002
-#define SPCI_FL_BASE3 0x0003
-#define SPCI_FL_BASE4 0x0004
-#define SPCI_FL_GET_BASE(x) (x & SPCI_FL_BASE_MASK)
-
-#define SPCI_FL_IRQ_MASK (0x0007 << 4)
-#define SPCI_FL_IRQBASE0 (0x0000 << 4)
-#define SPCI_FL_IRQBASE1 (0x0001 << 4)
-#define SPCI_FL_IRQBASE2 (0x0002 << 4)
-#define SPCI_FL_IRQBASE3 (0x0003 << 4)
-#define SPCI_FL_IRQBASE4 (0x0004 << 4)
-#define SPCI_FL_GET_IRQBASE(x) ((x & SPCI_FL_IRQ_MASK) >> 4)
-
-/* Use successive BARs (PCI base address registers),
- else use offset into some specified BAR */
-#define SPCI_FL_BASE_TABLE 0x0100
-
-/* Use successive entries in the irq resource table */
-#define SPCI_FL_IRQ_TABLE 0x0200
-
-/* Use the irq resource table instead of dev->irq */
-#define SPCI_FL_IRQRESOURCE 0x0400
-
-/* Use the Base address register size to cap number of ports */
-#define SPCI_FL_REGION_SZ_CAP 0x0800
-
-/* Do not use irq sharing for this device */
-#define SPCI_FL_NO_SHIRQ 0x1000
-
-/* This is a PNP device */
-#define SPCI_FL_ISPNP 0x2000
-
-#define SPCI_FL_PNPDEFAULT (SPCI_FL_IRQRESOURCE|SPCI_FL_ISPNP)
-
#endif /* _LINUX_SERIAL_H */
diff --git a/drivers/infiniband/include/ib_cache.h b/include/rdma/ib_cache.h
similarity index 95%
rename from drivers/infiniband/include/ib_cache.h
rename to include/rdma/ib_cache.h
index 44ef6bb..5bf9834 100644
--- a/drivers/infiniband/include/ib_cache.h
+++ b/include/rdma/ib_cache.h
@@ -1,5 +1,7 @@
/*
* Copyright (c) 2004 Topspin Communications. All rights reserved.
+ * Copyright (c) 2005 Intel Corporation. All rights reserved.
+ * Copyright (c) 2005 Sun Microsystems, Inc. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
@@ -35,7 +37,7 @@
#ifndef _IB_CACHE_H
#define _IB_CACHE_H
-#include <ib_verbs.h>
+#include <rdma/ib_verbs.h>
/**
* ib_get_cached_gid - Returns a cached GID table entry
diff --git a/drivers/infiniband/include/ib_cm.h b/include/rdma/ib_cm.h
similarity index 88%
rename from drivers/infiniband/include/ib_cm.h
rename to include/rdma/ib_cm.h
index da65011..77fe903 100644
--- a/drivers/infiniband/include/ib_cm.h
+++ b/include/rdma/ib_cm.h
@@ -37,8 +37,8 @@
#if !defined(IB_CM_H)
#define IB_CM_H
-#include <ib_mad.h>
-#include <ib_sa.h>
+#include <rdma/ib_mad.h>
+#include <rdma/ib_sa.h>
enum ib_cm_state {
IB_CM_IDLE,
@@ -115,7 +115,7 @@
struct ib_sa_path_rec *primary_path;
struct ib_sa_path_rec *alternate_path;
- u64 remote_ca_guid;
+ __be64 remote_ca_guid;
u32 remote_qkey;
u32 remote_qpn;
enum ib_qp_type qp_type;
@@ -132,7 +132,7 @@
};
struct ib_cm_rep_event_param {
- u64 remote_ca_guid;
+ __be64 remote_ca_guid;
u32 remote_qkey;
u32 remote_qpn;
u32 starting_psn;
@@ -146,39 +146,39 @@
};
enum ib_cm_rej_reason {
- IB_CM_REJ_NO_QP = __constant_htons(1),
- IB_CM_REJ_NO_EEC = __constant_htons(2),
- IB_CM_REJ_NO_RESOURCES = __constant_htons(3),
- IB_CM_REJ_TIMEOUT = __constant_htons(4),
- IB_CM_REJ_UNSUPPORTED = __constant_htons(5),
- IB_CM_REJ_INVALID_COMM_ID = __constant_htons(6),
- IB_CM_REJ_INVALID_COMM_INSTANCE = __constant_htons(7),
- IB_CM_REJ_INVALID_SERVICE_ID = __constant_htons(8),
- IB_CM_REJ_INVALID_TRANSPORT_TYPE = __constant_htons(9),
- IB_CM_REJ_STALE_CONN = __constant_htons(10),
- IB_CM_REJ_RDC_NOT_EXIST = __constant_htons(11),
- IB_CM_REJ_INVALID_GID = __constant_htons(12),
- IB_CM_REJ_INVALID_LID = __constant_htons(13),
- IB_CM_REJ_INVALID_SL = __constant_htons(14),
- IB_CM_REJ_INVALID_TRAFFIC_CLASS = __constant_htons(15),
- IB_CM_REJ_INVALID_HOP_LIMIT = __constant_htons(16),
- IB_CM_REJ_INVALID_PACKET_RATE = __constant_htons(17),
- IB_CM_REJ_INVALID_ALT_GID = __constant_htons(18),
- IB_CM_REJ_INVALID_ALT_LID = __constant_htons(19),
- IB_CM_REJ_INVALID_ALT_SL = __constant_htons(20),
- IB_CM_REJ_INVALID_ALT_TRAFFIC_CLASS = __constant_htons(21),
- IB_CM_REJ_INVALID_ALT_HOP_LIMIT = __constant_htons(22),
- IB_CM_REJ_INVALID_ALT_PACKET_RATE = __constant_htons(23),
- IB_CM_REJ_PORT_CM_REDIRECT = __constant_htons(24),
- IB_CM_REJ_PORT_REDIRECT = __constant_htons(25),
- IB_CM_REJ_INVALID_MTU = __constant_htons(26),
- IB_CM_REJ_INSUFFICIENT_RESP_RESOURCES = __constant_htons(27),
- IB_CM_REJ_CONSUMER_DEFINED = __constant_htons(28),
- IB_CM_REJ_INVALID_RNR_RETRY = __constant_htons(29),
- IB_CM_REJ_DUPLICATE_LOCAL_COMM_ID = __constant_htons(30),
- IB_CM_REJ_INVALID_CLASS_VERSION = __constant_htons(31),
- IB_CM_REJ_INVALID_FLOW_LABEL = __constant_htons(32),
- IB_CM_REJ_INVALID_ALT_FLOW_LABEL = __constant_htons(33)
+ IB_CM_REJ_NO_QP = 1,
+ IB_CM_REJ_NO_EEC = 2,
+ IB_CM_REJ_NO_RESOURCES = 3,
+ IB_CM_REJ_TIMEOUT = 4,
+ IB_CM_REJ_UNSUPPORTED = 5,
+ IB_CM_REJ_INVALID_COMM_ID = 6,
+ IB_CM_REJ_INVALID_COMM_INSTANCE = 7,
+ IB_CM_REJ_INVALID_SERVICE_ID = 8,
+ IB_CM_REJ_INVALID_TRANSPORT_TYPE = 9,
+ IB_CM_REJ_STALE_CONN = 10,
+ IB_CM_REJ_RDC_NOT_EXIST = 11,
+ IB_CM_REJ_INVALID_GID = 12,
+ IB_CM_REJ_INVALID_LID = 13,
+ IB_CM_REJ_INVALID_SL = 14,
+ IB_CM_REJ_INVALID_TRAFFIC_CLASS = 15,
+ IB_CM_REJ_INVALID_HOP_LIMIT = 16,
+ IB_CM_REJ_INVALID_PACKET_RATE = 17,
+ IB_CM_REJ_INVALID_ALT_GID = 18,
+ IB_CM_REJ_INVALID_ALT_LID = 19,
+ IB_CM_REJ_INVALID_ALT_SL = 20,
+ IB_CM_REJ_INVALID_ALT_TRAFFIC_CLASS = 21,
+ IB_CM_REJ_INVALID_ALT_HOP_LIMIT = 22,
+ IB_CM_REJ_INVALID_ALT_PACKET_RATE = 23,
+ IB_CM_REJ_PORT_CM_REDIRECT = 24,
+ IB_CM_REJ_PORT_REDIRECT = 25,
+ IB_CM_REJ_INVALID_MTU = 26,
+ IB_CM_REJ_INSUFFICIENT_RESP_RESOURCES = 27,
+ IB_CM_REJ_CONSUMER_DEFINED = 28,
+ IB_CM_REJ_INVALID_RNR_RETRY = 29,
+ IB_CM_REJ_DUPLICATE_LOCAL_COMM_ID = 30,
+ IB_CM_REJ_INVALID_CLASS_VERSION = 31,
+ IB_CM_REJ_INVALID_FLOW_LABEL = 32,
+ IB_CM_REJ_INVALID_ALT_FLOW_LABEL = 33
};
struct ib_cm_rej_event_param {
@@ -222,8 +222,7 @@
struct ib_cm_id *listen_id;
struct ib_device *device;
u8 port;
-
- u16 pkey;
+ u16 pkey;
};
enum ib_cm_sidr_status {
@@ -285,12 +284,12 @@
struct ib_cm_id {
ib_cm_handler cm_handler;
void *context;
- u64 service_id;
- u64 service_mask;
+ __be64 service_id;
+ __be64 service_mask;
enum ib_cm_state state; /* internal CM/debug use */
enum ib_cm_lap_state lap_state; /* internal CM/debug use */
- u32 local_id;
- u32 remote_id;
+ __be32 local_id;
+ __be32 remote_id;
};
/**
@@ -330,13 +329,13 @@
* IB_CM_ASSIGN_SERVICE_ID.
*/
int ib_cm_listen(struct ib_cm_id *cm_id,
- u64 service_id,
- u64 service_mask);
+ __be64 service_id,
+ __be64 service_mask);
struct ib_cm_req_param {
struct ib_sa_path_rec *primary_path;
struct ib_sa_path_rec *alternate_path;
- u64 service_id;
+ __be64 service_id;
u32 qp_num;
enum ib_qp_type qp_type;
u32 starting_psn;
@@ -528,7 +527,7 @@
struct ib_cm_sidr_req_param {
struct ib_sa_path_rec *path;
- u64 service_id;
+ __be64 service_id;
int timeout_ms;
const void *private_data;
u8 private_data_len;
diff --git a/drivers/infiniband/include/ib_fmr_pool.h b/include/rdma/ib_fmr_pool.h
similarity index 98%
rename from drivers/infiniband/include/ib_fmr_pool.h
rename to include/rdma/ib_fmr_pool.h
index 6c9e24d..86b7e93 100644
--- a/drivers/infiniband/include/ib_fmr_pool.h
+++ b/include/rdma/ib_fmr_pool.h
@@ -36,7 +36,7 @@
#if !defined(IB_FMR_POOL_H)
#define IB_FMR_POOL_H
-#include <ib_verbs.h>
+#include <rdma/ib_verbs.h>
struct ib_fmr_pool;
diff --git a/drivers/infiniband/include/ib_mad.h b/include/rdma/ib_mad.h
similarity index 97%
rename from drivers/infiniband/include/ib_mad.h
rename to include/rdma/ib_mad.h
index 491b6f2..fc6b1c1 100644
--- a/drivers/infiniband/include/ib_mad.h
+++ b/include/rdma/ib_mad.h
@@ -41,7 +41,7 @@
#include <linux/pci.h>
-#include <ib_verbs.h>
+#include <rdma/ib_verbs.h>
/* Management base version */
#define IB_MGMT_BASE_VERSION 1
@@ -90,6 +90,7 @@
#define IB_MGMT_RMPP_STATUS_SUCCESS 0
#define IB_MGMT_RMPP_STATUS_RESX 1
+#define IB_MGMT_RMPP_STATUS_ABORT_MIN 118
#define IB_MGMT_RMPP_STATUS_T2L 118
#define IB_MGMT_RMPP_STATUS_BAD_LEN 119
#define IB_MGMT_RMPP_STATUS_BAD_SEG 120
@@ -100,6 +101,7 @@
#define IB_MGMT_RMPP_STATUS_UNV 125
#define IB_MGMT_RMPP_STATUS_TMR 126
#define IB_MGMT_RMPP_STATUS_UNSPEC 127
+#define IB_MGMT_RMPP_STATUS_ABORT_MAX 127
#define IB_QP0 0
#define IB_QP1 __constant_htonl(1)
@@ -111,12 +113,12 @@
u8 mgmt_class;
u8 class_version;
u8 method;
- u16 status;
- u16 class_specific;
- u64 tid;
- u16 attr_id;
- u16 resv;
- u32 attr_mod;
+ __be16 status;
+ __be16 class_specific;
+ __be64 tid;
+ __be16 attr_id;
+ __be16 resv;
+ __be32 attr_mod;
};
struct ib_rmpp_hdr {
@@ -124,8 +126,8 @@
u8 rmpp_type;
u8 rmpp_rtime_flags;
u8 rmpp_status;
- u32 seg_num;
- u32 paylen_newwin;
+ __be32 seg_num;
+ __be32 paylen_newwin;
};
typedef u64 __bitwise ib_sa_comp_mask;
@@ -139,9 +141,9 @@
* the wire so we can't change the layout)
*/
struct ib_sa_hdr {
- u64 sm_key;
- u16 attr_offset;
- u16 reserved;
+ __be64 sm_key;
+ __be16 attr_offset;
+ __be16 reserved;
ib_sa_comp_mask comp_mask;
} __attribute__ ((packed));
diff --git a/drivers/infiniband/include/ib_pack.h b/include/rdma/ib_pack.h
similarity index 99%
rename from drivers/infiniband/include/ib_pack.h
rename to include/rdma/ib_pack.h
index fe480f3..f926020 100644
--- a/drivers/infiniband/include/ib_pack.h
+++ b/include/rdma/ib_pack.h
@@ -35,7 +35,7 @@
#ifndef IB_PACK_H
#define IB_PACK_H
-#include <ib_verbs.h>
+#include <rdma/ib_verbs.h>
enum {
IB_LRH_BYTES = 8,
diff --git a/drivers/infiniband/include/ib_sa.h b/include/rdma/ib_sa.h
similarity index 97%
rename from drivers/infiniband/include/ib_sa.h
rename to include/rdma/ib_sa.h
index 6d999f7..c022edf 100644
--- a/drivers/infiniband/include/ib_sa.h
+++ b/include/rdma/ib_sa.h
@@ -38,8 +38,8 @@
#include <linux/compiler.h>
-#include <ib_verbs.h>
-#include <ib_mad.h>
+#include <rdma/ib_verbs.h>
+#include <rdma/ib_mad.h>
enum {
IB_SA_CLASS_VERSION = 2, /* IB spec version 1.1/1.2 */
@@ -133,16 +133,16 @@
/* reserved */
union ib_gid dgid;
union ib_gid sgid;
- u16 dlid;
- u16 slid;
+ __be16 dlid;
+ __be16 slid;
int raw_traffic;
/* reserved */
- u32 flow_label;
+ __be32 flow_label;
u8 hop_limit;
u8 traffic_class;
int reversible;
u8 numb_path;
- u16 pkey;
+ __be16 pkey;
/* reserved */
u8 sl;
u8 mtu_selector;
@@ -176,18 +176,18 @@
struct ib_sa_mcmember_rec {
union ib_gid mgid;
union ib_gid port_gid;
- u32 qkey;
- u16 mlid;
+ __be32 qkey;
+ __be16 mlid;
u8 mtu_selector;
u8 mtu;
u8 traffic_class;
- u16 pkey;
+ __be16 pkey;
u8 rate_selector;
u8 rate;
u8 packet_life_time_selector;
u8 packet_life_time;
u8 sl;
- u32 flow_label;
+ __be32 flow_label;
u8 hop_limit;
u8 scope;
u8 join_state;
@@ -238,7 +238,7 @@
struct ib_sa_service_rec {
u64 id;
union ib_gid gid;
- u16 pkey;
+ __be16 pkey;
/* reserved */
u32 lease;
u8 key[16];
diff --git a/drivers/infiniband/include/ib_smi.h b/include/rdma/ib_smi.h
similarity index 94%
rename from drivers/infiniband/include/ib_smi.h
rename to include/rdma/ib_smi.h
index ca82165..87f6073 100644
--- a/drivers/infiniband/include/ib_smi.h
+++ b/include/rdma/ib_smi.h
@@ -39,9 +39,7 @@
#if !defined( IB_SMI_H )
#define IB_SMI_H
-#include <ib_mad.h>
-
-#define IB_LID_PERMISSIVE 0xFFFF
+#include <rdma/ib_mad.h>
#define IB_SMP_DATA_SIZE 64
#define IB_SMP_MAX_PATH_HOPS 64
@@ -51,16 +49,16 @@
u8 mgmt_class;
u8 class_version;
u8 method;
- u16 status;
+ __be16 status;
u8 hop_ptr;
u8 hop_cnt;
- u64 tid;
- u16 attr_id;
- u16 resv;
- u32 attr_mod;
- u64 mkey;
- u16 dr_slid;
- u16 dr_dlid;
+ __be64 tid;
+ __be16 attr_id;
+ __be16 resv;
+ __be32 attr_mod;
+ __be64 mkey;
+ __be16 dr_slid;
+ __be16 dr_dlid;
u8 reserved[28];
u8 data[IB_SMP_DATA_SIZE];
u8 initial_path[IB_SMP_MAX_PATH_HOPS];
diff --git a/drivers/infiniband/include/ib_user_cm.h b/include/rdma/ib_user_cm.h
similarity index 95%
rename from drivers/infiniband/include/ib_user_cm.h
rename to include/rdma/ib_user_cm.h
index 500b1af..72182d1 100644
--- a/drivers/infiniband/include/ib_user_cm.h
+++ b/include/rdma/ib_user_cm.h
@@ -88,15 +88,15 @@
};
struct ib_ucm_attr_id_resp {
- __u64 service_id;
- __u64 service_mask;
- __u32 local_id;
- __u32 remote_id;
+ __be64 service_id;
+ __be64 service_mask;
+ __be32 local_id;
+ __be32 remote_id;
};
struct ib_ucm_listen {
- __u64 service_id;
- __u64 service_mask;
+ __be64 service_id;
+ __be64 service_mask;
__u32 id;
};
@@ -114,13 +114,13 @@
struct ib_ucm_path_rec {
__u8 dgid[16];
__u8 sgid[16];
- __u16 dlid;
- __u16 slid;
+ __be16 dlid;
+ __be16 slid;
__u32 raw_traffic;
- __u32 flow_label;
+ __be32 flow_label;
__u32 reversible;
__u32 mtu;
- __u16 pkey;
+ __be16 pkey;
__u8 hop_limit;
__u8 traffic_class;
__u8 numb_path;
@@ -138,7 +138,7 @@
__u32 qpn;
__u32 qp_type;
__u32 psn;
- __u64 sid;
+ __be64 sid;
__u64 data;
__u64 primary_path;
__u64 alternate_path;
@@ -200,7 +200,7 @@
struct ib_ucm_sidr_req {
__u32 id;
__u32 timeout;
- __u64 sid;
+ __be64 sid;
__u64 data;
__u64 path;
__u16 pkey;
@@ -237,7 +237,7 @@
/* port */
struct ib_ucm_path_rec primary_path;
struct ib_ucm_path_rec alternate_path;
- __u64 remote_ca_guid;
+ __be64 remote_ca_guid;
__u32 remote_qkey;
__u32 remote_qpn;
__u32 qp_type;
@@ -253,7 +253,7 @@
};
struct ib_ucm_rep_event_resp {
- __u64 remote_ca_guid;
+ __be64 remote_ca_guid;
__u32 remote_qkey;
__u32 remote_qpn;
__u32 starting_psn;
diff --git a/drivers/infiniband/include/ib_user_mad.h b/include/rdma/ib_user_mad.h
similarity index 96%
rename from drivers/infiniband/include/ib_user_mad.h
rename to include/rdma/ib_user_mad.h
index a9a56b50..44537aa 100644
--- a/drivers/infiniband/include/ib_user_mad.h
+++ b/include/rdma/ib_user_mad.h
@@ -70,8 +70,6 @@
* @traffic_class - Traffic class in GRH
* @gid - Remote GID in GRH
* @flow_label - Flow label in GRH
- *
- * All multi-byte quantities are stored in network (big endian) byte order.
*/
struct ib_user_mad_hdr {
__u32 id;
@@ -79,9 +77,9 @@
__u32 timeout_ms;
__u32 retries;
__u32 length;
- __u32 qpn;
- __u32 qkey;
- __u16 lid;
+ __be32 qpn;
+ __be32 qkey;
+ __be16 lid;
__u8 sl;
__u8 path_bits;
__u8 grh_present;
@@ -89,7 +87,7 @@
__u8 hop_limit;
__u8 traffic_class;
__u8 gid[16];
- __u32 flow_label;
+ __be32 flow_label;
};
/**
diff --git a/drivers/infiniband/include/ib_user_verbs.h b/include/rdma/ib_user_verbs.h
similarity index 92%
rename from drivers/infiniband/include/ib_user_verbs.h
rename to include/rdma/ib_user_verbs.h
index 7c61370..7ebb01c 100644
--- a/drivers/infiniband/include/ib_user_verbs.h
+++ b/include/rdma/ib_user_verbs.h
@@ -78,7 +78,12 @@
IB_USER_VERBS_CMD_POST_SEND,
IB_USER_VERBS_CMD_POST_RECV,
IB_USER_VERBS_CMD_ATTACH_MCAST,
- IB_USER_VERBS_CMD_DETACH_MCAST
+ IB_USER_VERBS_CMD_DETACH_MCAST,
+ IB_USER_VERBS_CMD_CREATE_SRQ,
+ IB_USER_VERBS_CMD_MODIFY_SRQ,
+ IB_USER_VERBS_CMD_QUERY_SRQ,
+ IB_USER_VERBS_CMD_DESTROY_SRQ,
+ IB_USER_VERBS_CMD_POST_SRQ_RECV
};
/*
@@ -143,8 +148,8 @@
struct ib_uverbs_query_device_resp {
__u64 fw_ver;
- __u64 node_guid;
- __u64 sys_image_guid;
+ __be64 node_guid;
+ __be64 sys_image_guid;
__u64 max_mr_size;
__u64 page_size_cap;
__u32 vendor_id;
@@ -386,4 +391,32 @@
__u64 driver_data[0];
};
+struct ib_uverbs_create_srq {
+ __u64 response;
+ __u64 user_handle;
+ __u32 pd_handle;
+ __u32 max_wr;
+ __u32 max_sge;
+ __u32 srq_limit;
+ __u64 driver_data[0];
+};
+
+struct ib_uverbs_create_srq_resp {
+ __u32 srq_handle;
+};
+
+struct ib_uverbs_modify_srq {
+ __u32 srq_handle;
+ __u32 attr_mask;
+ __u32 max_wr;
+ __u32 max_sge;
+ __u32 srq_limit;
+ __u32 reserved;
+ __u64 driver_data[0];
+};
+
+struct ib_uverbs_destroy_srq {
+ __u32 srq_handle;
+};
+
#endif /* IB_USER_VERBS_H */
diff --git a/drivers/infiniband/include/ib_verbs.h b/include/rdma/ib_verbs.h
similarity index 90%
rename from drivers/infiniband/include/ib_verbs.h
rename to include/rdma/ib_verbs.h
index 5d24eda..e16cf94 100644
--- a/drivers/infiniband/include/ib_verbs.h
+++ b/include/rdma/ib_verbs.h
@@ -4,6 +4,7 @@
* Copyright (c) 2004 Intel Corporation. All rights reserved.
* Copyright (c) 2004 Topspin Corporation. All rights reserved.
* Copyright (c) 2004 Voltaire Corporation. All rights reserved.
+ * Copyright (c) 2005 Sun Microsystems, Inc. All rights reserved.
* Copyright (c) 2005 Cisco Systems. All rights reserved.
*
* This software is available to you under a choice of one of two
@@ -50,8 +51,8 @@
union ib_gid {
u8 raw[16];
struct {
- u64 subnet_prefix;
- u64 interface_id;
+ __be64 subnet_prefix;
+ __be64 interface_id;
} global;
};
@@ -87,8 +88,8 @@
struct ib_device_attr {
u64 fw_ver;
- u64 node_guid;
- u64 sys_image_guid;
+ __be64 node_guid;
+ __be64 sys_image_guid;
u64 max_mr_size;
u64 page_size_cap;
u32 vendor_id;
@@ -255,7 +256,10 @@
IB_EVENT_PORT_ERR,
IB_EVENT_LID_CHANGE,
IB_EVENT_PKEY_CHANGE,
- IB_EVENT_SM_CHANGE
+ IB_EVENT_SM_CHANGE,
+ IB_EVENT_SRQ_ERR,
+ IB_EVENT_SRQ_LIMIT_REACHED,
+ IB_EVENT_QP_LAST_WQE_REACHED
};
struct ib_event {
@@ -263,6 +267,7 @@
union {
struct ib_cq *cq;
struct ib_qp *qp;
+ struct ib_srq *srq;
u8 port_num;
} element;
enum ib_event_type event;
@@ -290,8 +295,8 @@
};
struct ib_grh {
- u32 version_tclass_flow;
- u16 paylen;
+ __be32 version_tclass_flow;
+ __be16 paylen;
u8 next_hdr;
u8 hop_limit;
union ib_gid sgid;
@@ -302,6 +307,8 @@
IB_MULTICAST_QPN = 0xffffff
};
+#define IB_LID_PERMISSIVE __constant_htons(0xFFFF)
+
enum ib_ah_flags {
IB_AH_GRH = 1
};
@@ -383,6 +390,23 @@
IB_CQ_NEXT_COMP
};
+enum ib_srq_attr_mask {
+ IB_SRQ_MAX_WR = 1 << 0,
+ IB_SRQ_LIMIT = 1 << 1,
+};
+
+struct ib_srq_attr {
+ u32 max_wr;
+ u32 max_sge;
+ u32 srq_limit;
+};
+
+struct ib_srq_init_attr {
+ void (*event_handler)(struct ib_event *, void *);
+ void *srq_context;
+ struct ib_srq_attr attr;
+};
+
struct ib_qp_cap {
u32 max_send_wr;
u32 max_recv_wr;
@@ -710,10 +734,11 @@
};
struct ib_srq {
- struct ib_device *device;
- struct ib_uobject *uobject;
- struct ib_pd *pd;
- void *srq_context;
+ struct ib_device *device;
+ struct ib_pd *pd;
+ struct ib_uobject *uobject;
+ void (*event_handler)(struct ib_event *, void *);
+ void *srq_context;
atomic_t usecnt;
};
@@ -827,6 +852,18 @@
int (*query_ah)(struct ib_ah *ah,
struct ib_ah_attr *ah_attr);
int (*destroy_ah)(struct ib_ah *ah);
+ struct ib_srq * (*create_srq)(struct ib_pd *pd,
+ struct ib_srq_init_attr *srq_init_attr,
+ struct ib_udata *udata);
+ int (*modify_srq)(struct ib_srq *srq,
+ struct ib_srq_attr *srq_attr,
+ enum ib_srq_attr_mask srq_attr_mask);
+ int (*query_srq)(struct ib_srq *srq,
+ struct ib_srq_attr *srq_attr);
+ int (*destroy_srq)(struct ib_srq *srq);
+ int (*post_srq_recv)(struct ib_srq *srq,
+ struct ib_recv_wr *recv_wr,
+ struct ib_recv_wr **bad_recv_wr);
struct ib_qp * (*create_qp)(struct ib_pd *pd,
struct ib_qp_init_attr *qp_init_attr,
struct ib_udata *udata);
@@ -1039,6 +1076,65 @@
int ib_destroy_ah(struct ib_ah *ah);
/**
+ * ib_create_srq - Creates a SRQ associated with the specified protection
+ * domain.
+ * @pd: The protection domain associated with the SRQ.
+ * @srq_init_attr: A list of initial attributes required to create the SRQ.
+ *
+ * srq_attr->max_wr and srq_attr->max_sge are read the determine the
+ * requested size of the SRQ, and set to the actual values allocated
+ * on return. If ib_create_srq() succeeds, then max_wr and max_sge
+ * will always be at least as large as the requested values.
+ */
+struct ib_srq *ib_create_srq(struct ib_pd *pd,
+ struct ib_srq_init_attr *srq_init_attr);
+
+/**
+ * ib_modify_srq - Modifies the attributes for the specified SRQ.
+ * @srq: The SRQ to modify.
+ * @srq_attr: On input, specifies the SRQ attributes to modify. On output,
+ * the current values of selected SRQ attributes are returned.
+ * @srq_attr_mask: A bit-mask used to specify which attributes of the SRQ
+ * are being modified.
+ *
+ * The mask may contain IB_SRQ_MAX_WR to resize the SRQ and/or
+ * IB_SRQ_LIMIT to set the SRQ's limit and request notification when
+ * the number of receives queued drops below the limit.
+ */
+int ib_modify_srq(struct ib_srq *srq,
+ struct ib_srq_attr *srq_attr,
+ enum ib_srq_attr_mask srq_attr_mask);
+
+/**
+ * ib_query_srq - Returns the attribute list and current values for the
+ * specified SRQ.
+ * @srq: The SRQ to query.
+ * @srq_attr: The attributes of the specified SRQ.
+ */
+int ib_query_srq(struct ib_srq *srq,
+ struct ib_srq_attr *srq_attr);
+
+/**
+ * ib_destroy_srq - Destroys the specified SRQ.
+ * @srq: The SRQ to destroy.
+ */
+int ib_destroy_srq(struct ib_srq *srq);
+
+/**
+ * ib_post_srq_recv - Posts a list of work requests to the specified SRQ.
+ * @srq: The SRQ to post the work request on.
+ * @recv_wr: A list of work requests to post on the receive queue.
+ * @bad_recv_wr: On an immediate failure, this parameter will reference
+ * the work request that failed to be posted on the QP.
+ */
+static inline int ib_post_srq_recv(struct ib_srq *srq,
+ struct ib_recv_wr *recv_wr,
+ struct ib_recv_wr **bad_recv_wr)
+{
+ return srq->device->post_srq_recv(srq, recv_wr, bad_recv_wr);
+}
+
+/**
* ib_create_qp - Creates a QP associated with the specified protection
* domain.
* @pd: The protection domain associated with the QP.