OHCI: make autostop conditional on CONFIG_PM
Unlike UHCI, OHCI does not exert any DMA load on the system when no
devices are connected. Consequently there is no advantage to doing
an autostop other than the power savings, so we shouldn't compile the
necessary code unless CONFIG_PM is enabled.
This patch (as820) makes the root-hub suspend and resume routines
conditional on CONFIG_PM. It also prevents autostop from activating
if the device_may_wakeup flag isn't set; some people use this flag to
alert the driver about Resume-Detect bugs in the hardware.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff --git a/drivers/usb/host/ohci-hub.c b/drivers/usb/host/ohci-hub.c
index 4c94927..2441642 100644
--- a/drivers/usb/host/ohci-hub.c
+++ b/drivers/usb/host/ohci-hub.c
@@ -56,7 +56,6 @@
#ifdef CONFIG_PM
static int ohci_restart(struct ohci_hcd *ohci);
-#endif
static int ohci_rh_suspend (struct ohci_hcd *ohci, int autostop)
__releases(ohci->lock)
@@ -187,7 +186,6 @@
ohci_dbg (ohci, "lost power\n");
status = -EBUSY;
}
-#ifdef CONFIG_PM
if (status == -EBUSY) {
if (!autostopped) {
spin_unlock_irq (&ohci->lock);
@@ -197,7 +195,6 @@
}
return status;
}
-#endif
if (status != -EINPROGRESS)
return status;
if (autostopped)
@@ -291,8 +288,6 @@
return 0;
}
-#ifdef CONFIG_PM
-
static int ohci_bus_suspend (struct usb_hcd *hcd)
{
struct ohci_hcd *ohci = hcd_to_ohci (hcd);
@@ -330,6 +325,83 @@
return rc;
}
+/* Carry out polling-, autostop-, and autoresume-related state changes */
+static int ohci_root_hub_state_changes(struct ohci_hcd *ohci, int changed,
+ int any_connected)
+{
+ int poll_rh = 1;
+
+ switch (ohci->hc_control & OHCI_CTRL_HCFS) {
+
+ case OHCI_USB_OPER:
+ /* keep on polling until we know a device is connected
+ * and RHSC is enabled */
+ if (!ohci->autostop) {
+ if (any_connected ||
+ !device_may_wakeup(&ohci_to_hcd(ohci)
+ ->self.root_hub->dev)) {
+ if (ohci_readl(ohci, &ohci->regs->intrenable) &
+ OHCI_INTR_RHSC)
+ poll_rh = 0;
+ } else {
+ ohci->autostop = 1;
+ ohci->next_statechange = jiffies + HZ;
+ }
+
+ /* if no devices have been attached for one second, autostop */
+ } else {
+ if (changed || any_connected) {
+ ohci->autostop = 0;
+ ohci->next_statechange = jiffies +
+ STATECHANGE_DELAY;
+ } else if (time_after_eq(jiffies,
+ ohci->next_statechange)
+ && !ohci->ed_rm_list
+ && !(ohci->hc_control &
+ OHCI_SCHED_ENABLES)) {
+ ohci_rh_suspend(ohci, 1);
+ }
+ }
+ break;
+
+ /* if there is a port change, autostart or ask to be resumed */
+ case OHCI_USB_SUSPEND:
+ case OHCI_USB_RESUME:
+ if (changed) {
+ if (ohci->autostop)
+ ohci_rh_resume(ohci);
+ else
+ usb_hcd_resume_root_hub(ohci_to_hcd(ohci));
+ } else {
+ /* everything is idle, no need for polling */
+ poll_rh = 0;
+ }
+ break;
+ }
+ return poll_rh;
+}
+
+#else /* CONFIG_PM */
+
+static inline int ohci_rh_resume(struct ohci_hcd *ohci)
+{
+ return 0;
+}
+
+/* Carry out polling-related state changes.
+ * autostop isn't used when CONFIG_PM is turned off.
+ */
+static int ohci_root_hub_state_changes(struct ohci_hcd *ohci, int changed,
+ int any_connected)
+{
+ int poll_rh = 1;
+
+ /* keep on polling until RHSC is enabled */
+ if (ohci_readl(ohci, &ohci->regs->intrenable) & OHCI_INTR_RHSC)
+ poll_rh = 0;
+ return poll_rh;
+}
+
#endif /* CONFIG_PM */
/*-------------------------------------------------------------------------*/
@@ -382,55 +454,8 @@
}
}
- hcd->poll_rh = 1;
-
- /* carry out appropriate state changes */
- switch (ohci->hc_control & OHCI_CTRL_HCFS) {
-
- case OHCI_USB_OPER:
- /* keep on polling until we know a device is connected
- * and RHSC is enabled */
- if (!ohci->autostop) {
- if (any_connected) {
- if (ohci_readl(ohci, &ohci->regs->intrenable) &
- OHCI_INTR_RHSC)
- hcd->poll_rh = 0;
- } else {
- ohci->autostop = 1;
- ohci->next_statechange = jiffies + HZ;
- }
-
- /* if no devices have been attached for one second, autostop */
- } else {
- if (changed || any_connected) {
- ohci->autostop = 0;
- ohci->next_statechange = jiffies +
- STATECHANGE_DELAY;
- } else if (device_may_wakeup(&hcd->self.root_hub->dev)
- && time_after_eq(jiffies,
- ohci->next_statechange)
- && !ohci->ed_rm_list
- && !(ohci->hc_control &
- OHCI_SCHED_ENABLES)) {
- ohci_rh_suspend (ohci, 1);
- }
- }
- break;
-
- /* if there is a port change, autostart or ask to be resumed */
- case OHCI_USB_SUSPEND:
- case OHCI_USB_RESUME:
- if (changed) {
- if (ohci->autostop)
- ohci_rh_resume (ohci);
- else
- usb_hcd_resume_root_hub (hcd);
- } else {
- /* everything is idle, no need for polling */
- hcd->poll_rh = 0;
- }
- break;
- }
+ hcd->poll_rh = ohci_root_hub_state_changes(ohci, changed,
+ any_connected);
done:
spin_unlock_irqrestore (&ohci->lock, flags);