ide: update references to Documentation/ide/ide.txt (v2)
Fix all references to Documentation/ide/ide.txt.
Add/update ide/00-INDEX file.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
diff --git a/Documentation/cdrom/ide-cd b/Documentation/cdrom/ide-cd
index 29721bf..91c0dcc 100644
--- a/Documentation/cdrom/ide-cd
+++ b/Documentation/cdrom/ide-cd
@@ -45,7 +45,7 @@
---------------
0. The ide-cd relies on the ide disk driver. See
- Documentation/ide.txt for up-to-date information on the ide
+ Documentation/ide/ide.txt for up-to-date information on the ide
driver.
1. Make sure that the ide and ide-cd drivers are compiled into the
@@ -64,7 +64,7 @@
Depending on what type of IDE interface you have, you may need to
specify additional configuration options. See
- Documentation/ide.txt.
+ Documentation/ide/ide.txt.
2. You should also ensure that the iso9660 filesystem is either
compiled into the kernel or available as a loadable module. You
@@ -84,7 +84,7 @@
on the primary IDE interface are called `hda' and `hdb',
respectively. The drives on the secondary interface are called
`hdc' and `hdd'. (Interfaces at other locations get other letters
- in the third position; see Documentation/ide.txt.)
+ in the third position; see Documentation/ide/ide.txt.)
If you want your CDROM drive to be found automatically by the
driver, you should make sure your IDE interface uses either the
@@ -93,7 +93,7 @@
be jumpered as `master'. (If for some reason you cannot configure
your system in this manner, you can probably still use the driver.
You may have to pass extra configuration information to the kernel
- when you boot, however. See Documentation/ide.txt for more
+ when you boot, however. See Documentation/ide/ide.txt for more
information.)
4. Boot the system. If the drive is recognized, you should see a
@@ -201,7 +201,7 @@
This section discusses some common problems encountered when trying to
use the driver, and some possible solutions. Note that if you are
experiencing problems, you should probably also review
-Documentation/ide.txt for current information about the underlying
+Documentation/ide/ide.txt for current information about the underlying
IDE support code. Some of these items apply only to earlier versions
of the driver, but are mentioned here for completeness.
@@ -211,7 +211,7 @@
a. Drive is not detected during booting.
- Review the configuration instructions above and in
- Documentation/ide.txt, and check how your hardware is
+ Documentation/ide/ide.txt, and check how your hardware is
configured.
- If your drive is the only device on an IDE interface, it should
@@ -219,7 +219,7 @@
- If your IDE interface is not at the standard addresses of 0x170
or 0x1f0, you'll need to explicitly inform the driver using a
- lilo option. See Documentation/ide.txt. (This feature was
+ lilo option. See Documentation/ide/ide.txt. (This feature was
added around kernel version 1.3.30.)
- If the autoprobing is not finding your drive, you can tell the
@@ -245,7 +245,7 @@
Support for some interfaces needing extra initialization is
provided in later 1.3.x kernels. You may need to turn on
additional kernel configuration options to get them to work;
- see Documentation/ide.txt.
+ see Documentation/ide/ide.txt.
Even if support is not available for your interface, you may be
able to get it to work with the following procedure. First boot
@@ -299,7 +299,7 @@
be worked around by specifying the `serialize' option when
booting. Recent kernels should be able to detect the need for
this automatically in most cases, but the detection is not
- foolproof. See Documentation/ide.txt for more information
+ foolproof. See Documentation/ide/ide.txt for more information
about the `serialize' option and the CMD640B.
- Note that many MS-DOS CDROM drivers will work with such buggy