drm/i915: skip FDI & PCH enabling for DP_A
eDP on the CPU doesn't need the PCH set up at all, it can in fact cause
problems. So avoid FDI training and PCH PLL enabling in that case.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index dcb8217..9ca1bb2 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -2045,6 +2045,31 @@
atomic_read(&obj->pending_flip) == 0);
}
+static bool intel_crtc_driving_pch(struct drm_crtc *crtc)
+{
+ struct drm_device *dev = crtc->dev;
+ struct drm_mode_config *mode_config = &dev->mode_config;
+ struct intel_encoder *encoder;
+
+ /*
+ * If there's a non-PCH eDP on this crtc, it must be DP_A, and that
+ * must be driven by its own crtc; no sharing is possible.
+ */
+ list_for_each_entry(encoder, &mode_config->encoder_list, base.head) {
+ if (encoder->base.crtc != crtc)
+ continue;
+
+ switch (encoder->type) {
+ case INTEL_OUTPUT_EDP:
+ if (!intel_encoder_is_pch_edp(&encoder->base))
+ return false;
+ continue;
+ }
+ }
+
+ return true;
+}
+
static void ironlake_crtc_enable(struct drm_crtc *crtc)
{
struct drm_device *dev = crtc->dev;
@@ -2053,6 +2078,7 @@
int pipe = intel_crtc->pipe;
int plane = intel_crtc->plane;
u32 reg, temp;
+ bool is_pch_port = false;
if (intel_crtc->active)
return;
@@ -2066,7 +2092,56 @@
I915_WRITE(PCH_LVDS, temp | LVDS_PORT_EN);
}
- ironlake_fdi_enable(crtc);
+ is_pch_port = intel_crtc_driving_pch(crtc);
+
+ if (is_pch_port)
+ ironlake_fdi_enable(crtc);
+ else {
+ /* disable CPU FDI tx and PCH FDI rx */
+ reg = FDI_TX_CTL(pipe);
+ temp = I915_READ(reg);
+ I915_WRITE(reg, temp & ~FDI_TX_ENABLE);
+ POSTING_READ(reg);
+
+ reg = FDI_RX_CTL(pipe);
+ temp = I915_READ(reg);
+ temp &= ~(0x7 << 16);
+ temp |= (I915_READ(PIPECONF(pipe)) & PIPE_BPC_MASK) << 11;
+ I915_WRITE(reg, temp & ~FDI_RX_ENABLE);
+
+ POSTING_READ(reg);
+ udelay(100);
+
+ /* Ironlake workaround, disable clock pointer after downing FDI */
+ if (HAS_PCH_IBX(dev))
+ I915_WRITE(FDI_RX_CHICKEN(pipe),
+ I915_READ(FDI_RX_CHICKEN(pipe) &
+ ~FDI_RX_PHASE_SYNC_POINTER_ENABLE));
+
+ /* still set train pattern 1 */
+ reg = FDI_TX_CTL(pipe);
+ temp = I915_READ(reg);
+ temp &= ~FDI_LINK_TRAIN_NONE;
+ temp |= FDI_LINK_TRAIN_PATTERN_1;
+ I915_WRITE(reg, temp);
+
+ reg = FDI_RX_CTL(pipe);
+ temp = I915_READ(reg);
+ if (HAS_PCH_CPT(dev)) {
+ temp &= ~FDI_LINK_TRAIN_PATTERN_MASK_CPT;
+ temp |= FDI_LINK_TRAIN_PATTERN_1_CPT;
+ } else {
+ temp &= ~FDI_LINK_TRAIN_NONE;
+ temp |= FDI_LINK_TRAIN_PATTERN_1;
+ }
+ /* BPC in FDI rx is consistent with that in PIPECONF */
+ temp &= ~(0x07 << 16);
+ temp |= (I915_READ(PIPECONF(pipe)) & PIPE_BPC_MASK) << 11;
+ I915_WRITE(reg, temp);
+
+ POSTING_READ(reg);
+ udelay(100);
+ }
/* Enable panel fitting for LVDS */
if (dev_priv->pch_pf_size &&
@@ -2100,6 +2175,10 @@
intel_flush_display_plane(dev, plane);
}
+ /* Skip the PCH stuff if possible */
+ if (!is_pch_port)
+ goto done;
+
/* For PCH output, training FDI link */
if (IS_GEN6(dev))
gen6_fdi_link_train(crtc);
@@ -2184,7 +2263,7 @@
I915_WRITE(reg, temp | TRANS_ENABLE);
if (wait_for(I915_READ(reg) & TRANS_STATE_ENABLE, 100))
DRM_ERROR("failed to enable transcoder %d\n", pipe);
-
+done:
intel_crtc_load_lut(crtc);
intel_update_fbc(dev);
intel_crtc_update_cursor(crtc, true);