[SCSI] hpsa: factor out driver name
Sometimes, for testing purposes (e.g. testing rmmod on a system
that normally boots using hpsa) it's nice to rename the driver
and split it into two drivers and restrict it to certain
controllers. This makes that easier.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
diff --git a/drivers/scsi/hpsa.c b/drivers/scsi/hpsa.c
index 68df3da..d048b69 100644
--- a/drivers/scsi/hpsa.c
+++ b/drivers/scsi/hpsa.c
@@ -56,6 +56,7 @@
/* HPSA_DRIVER_VERSION must be 3 byte values (0-255) separated by '.' */
#define HPSA_DRIVER_VERSION "2.0.2-1"
#define DRIVER_NAME "HP HPSA Driver (v " HPSA_DRIVER_VERSION ")"
+#define HPSA "hpsa"
/* How long to wait (in milliseconds) for board to go into simple mode */
#define MAX_CONFIG_WAIT 30000
@@ -202,30 +203,30 @@
switch (c->err_info->SenseInfo[12]) {
case STATE_CHANGED:
- dev_warn(&h->pdev->dev, "hpsa%d: a state change "
+ dev_warn(&h->pdev->dev, HPSA "%d: a state change "
"detected, command retried\n", h->ctlr);
break;
case LUN_FAILED:
- dev_warn(&h->pdev->dev, "hpsa%d: LUN failure "
+ dev_warn(&h->pdev->dev, HPSA "%d: LUN failure "
"detected, action required\n", h->ctlr);
break;
case REPORT_LUNS_CHANGED:
- dev_warn(&h->pdev->dev, "hpsa%d: report LUN data "
+ dev_warn(&h->pdev->dev, HPSA "%d: report LUN data "
"changed, action required\n", h->ctlr);
/*
* Note: this REPORT_LUNS_CHANGED condition only occurs on the MSA2012.
*/
break;
case POWER_OR_RESET:
- dev_warn(&h->pdev->dev, "hpsa%d: a power on "
+ dev_warn(&h->pdev->dev, HPSA "%d: a power on "
"or device reset detected\n", h->ctlr);
break;
case UNIT_ATTENTION_CLEARED:
- dev_warn(&h->pdev->dev, "hpsa%d: unit attention "
+ dev_warn(&h->pdev->dev, HPSA "%d: unit attention "
"cleared by another initiator\n", h->ctlr);
break;
default:
- dev_warn(&h->pdev->dev, "hpsa%d: unknown "
+ dev_warn(&h->pdev->dev, HPSA "%d: unknown "
"unit attention detected\n", h->ctlr);
break;
}
@@ -475,8 +476,8 @@
static struct scsi_host_template hpsa_driver_template = {
.module = THIS_MODULE,
- .name = "hpsa",
- .proc_name = "hpsa",
+ .name = HPSA,
+ .proc_name = HPSA,
.queuecommand = hpsa_scsi_queue_command,
.scan_start = hpsa_scan_start,
.scan_finished = hpsa_scan_finished,
@@ -3343,7 +3344,7 @@
static __devinit void init_driver_version(char *driver_version, int len)
{
memset(driver_version, 0, len);
- strncpy(driver_version, "hpsa " HPSA_DRIVER_VERSION, len - 1);
+ strncpy(driver_version, HPSA " " HPSA_DRIVER_VERSION, len - 1);
}
static __devinit int write_driver_ver_to_cfgtable(
@@ -3924,7 +3925,7 @@
return err;
}
- err = pci_request_regions(h->pdev, "hpsa");
+ err = pci_request_regions(h->pdev, HPSA);
if (err) {
dev_err(&h->pdev->dev,
"cannot obtain PCI resources, aborting\n");
@@ -4242,7 +4243,7 @@
spin_lock_init(&lockup_detector_lock);
hpsa_lockup_detector =
kthread_run(detect_controller_lockup_thread,
- NULL, "hpsa");
+ NULL, HPSA);
}
if (!hpsa_lockup_detector) {
dev_warn(&h->pdev->dev,
@@ -4314,7 +4315,7 @@
if (rc != 0)
goto clean1;
- sprintf(h->devname, "hpsa%d", number_of_controllers);
+ sprintf(h->devname, HPSA "%d", number_of_controllers);
h->ctlr = number_of_controllers;
number_of_controllers++;
@@ -4528,7 +4529,7 @@
}
static struct pci_driver hpsa_pci_driver = {
- .name = "hpsa",
+ .name = HPSA,
.probe = hpsa_init_one,
.remove = __devexit_p(hpsa_remove_one),
.id_table = hpsa_pci_device_id, /* id_table */
diff --git a/drivers/scsi/hpsa.h b/drivers/scsi/hpsa.h
index b4b97eb..7b28d54 100644
--- a/drivers/scsi/hpsa.h
+++ b/drivers/scsi/hpsa.h
@@ -316,7 +316,7 @@
dev_dbg(&h->pdev->dev, "Read %lx back from board\n",
register_value);
else
- dev_dbg(&h->pdev->dev, "hpsa: FIFO Empty read\n");
+ dev_dbg(&h->pdev->dev, "FIFO Empty read\n");
#endif
return register_value;