wireless: indent kernel-doc with tabs
Almost everywhere tabs are used to indent continuation
lines, replace the few places that use spaces.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
diff --git a/include/net/mac80211.h b/include/net/mac80211.h
index 5b7a3da..7c5dc78 100644
--- a/include/net/mac80211.h
+++ b/include/net/mac80211.h
@@ -1004,11 +1004,11 @@
* @radar_enabled: whether radar detection is enabled
*
* @long_frame_max_tx_count: Maximum number of transmissions for a "long" frame
- * (a frame not RTS protected), called "dot11LongRetryLimit" in 802.11,
- * but actually means the number of transmissions not the number of retries
+ * (a frame not RTS protected), called "dot11LongRetryLimit" in 802.11,
+ * but actually means the number of transmissions not the number of retries
* @short_frame_max_tx_count: Maximum number of transmissions for a "short"
- * frame, called "dot11ShortRetryLimit" in 802.11, but actually means the
- * number of transmissions not the number of retries
+ * frame, called "dot11ShortRetryLimit" in 802.11, but actually means the
+ * number of transmissions not the number of retries
*
* @smps_mode: spatial multiplexing powersave mode; note that
* %IEEE80211_SMPS_STATIC is used when the device is not
@@ -1092,7 +1092,7 @@
* be off when it is %NULL there can still be races and packets could be
* processed after it switches back to %NULL.
* @debugfs_dir: debugfs dentry, can be used by drivers to create own per
- * interface debug files. Note that it will be NULL for the virtual
+ * interface debug files. Note that it will be NULL for the virtual
* monitor interface (if that is requested.)
* @drv_priv: data area for driver use, will always be aligned to
* sizeof(void *).
@@ -1425,10 +1425,10 @@
* the stack.
*
* @IEEE80211_HW_CONNECTION_MONITOR:
- * The hardware performs its own connection monitoring, including
- * periodic keep-alives to the AP and probing the AP on beacon loss.
- * When this flag is set, signaling beacon-loss will cause an immediate
- * change to disassociated state.
+ * The hardware performs its own connection monitoring, including
+ * periodic keep-alives to the AP and probing the AP on beacon loss.
+ * When this flag is set, signaling beacon-loss will cause an immediate
+ * change to disassociated state.
*
* @IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC:
* This device needs to get data from beacon before association (i.e.
@@ -1526,10 +1526,10 @@
* @channel_change_time: time (in microseconds) it takes to change channels.
*
* @max_signal: Maximum value for signal (rssi) in RX information, used
- * only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB
+ * only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB
*
* @max_listen_interval: max listen interval in units of beacon interval
- * that HW supports
+ * that HW supports
*
* @queues: number of available hardware transmit queues for
* data packets. WMM/QoS requires at least four, these
@@ -2443,7 +2443,7 @@
* The callback can sleep.
*
* @set_tsf: Set the TSF timer to the specified value in the firmware/hardware.
- * Currently, this is only used for IBSS mode debugging. Is not a
+ * Currently, this is only used for IBSS mode debugging. Is not a
* required function.
* The callback can sleep.
*