wireless: indent kernel-doc with tabs
Almost everywhere tabs are used to indent continuation
lines, replace the few places that use spaces.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
index 79c2277..4940960 100644
--- a/include/net/cfg80211.h
+++ b/include/net/cfg80211.h
@@ -490,7 +490,7 @@
* @channel: the channel this survey record reports, mandatory
* @filled: bitflag of flags from &enum survey_info_flags
* @noise: channel noise in dBm. This and all following fields are
- * optional
+ * optional
* @channel_time: amount of time in ms the radio spent on the channel
* @channel_time_busy: amount of time the primary channel was sensed busy
* @channel_time_ext_busy: amount of time the extension channel was sensed busy
@@ -546,9 +546,9 @@
/**
* struct cfg80211_beacon_data - beacon data
* @head: head portion of beacon (before TIM IE)
- * or %NULL if not changed
+ * or %NULL if not changed
* @tail: tail portion of beacon (after TIM IE)
- * or %NULL if not changed
+ * or %NULL if not changed
* @head_len: length of @head
* @tail_len: length of @tail
* @beacon_ies: extra information element(s) to add into Beacon frames or %NULL
@@ -764,7 +764,7 @@
* @STATION_INFO_PLINK_STATE: @plink_state filled
* @STATION_INFO_SIGNAL: @signal filled
* @STATION_INFO_TX_BITRATE: @txrate fields are filled
- * (tx_bitrate, tx_bitrate_flags and tx_bitrate_mcs)
+ * (tx_bitrate, tx_bitrate_flags and tx_bitrate_mcs)
* @STATION_INFO_RX_PACKETS: @rx_packets filled with 32-bit value
* @STATION_INFO_TX_PACKETS: @tx_packets filled with 32-bit value
* @STATION_INFO_TX_RETRIES: @tx_retries filled
@@ -1509,7 +1509,7 @@
* @prev_bssid: previous BSSID, if not %NULL use reassociate frame
* @flags: See &enum cfg80211_assoc_req_flags
* @ht_capa: HT Capabilities over-rides. Values set in ht_capa_mask
- * will be used in ht_capa. Un-supported values will be ignored.
+ * will be used in ht_capa. Un-supported values will be ignored.
* @ht_capa_mask: The bits of ht_capa which are to be used.
* @vht_capa: VHT capability override
* @vht_capa_mask: VHT capability mask indicating which fields to use
@@ -1593,7 +1593,7 @@
* @basic_rates: bitmap of basic rates to use when creating the IBSS
* @mcast_rate: per-band multicast rate index + 1 (0: disabled)
* @ht_capa: HT Capabilities over-rides. Values set in ht_capa_mask
- * will be used in ht_capa. Un-supported values will be ignored.
+ * will be used in ht_capa. Un-supported values will be ignored.
* @ht_capa_mask: The bits of ht_capa which are to be used.
*/
struct cfg80211_ibss_params {
@@ -1635,9 +1635,9 @@
* @key: WEP key for shared key authentication
* @flags: See &enum cfg80211_assoc_req_flags
* @bg_scan_period: Background scan period in seconds
- * or -1 to indicate that default value is to be used.
+ * or -1 to indicate that default value is to be used.
* @ht_capa: HT Capabilities over-rides. Values set in ht_capa_mask
- * will be used in ht_capa. Un-supported values will be ignored.
+ * will be used in ht_capa. Un-supported values will be ignored.
* @ht_capa_mask: The bits of ht_capa which are to be used.
* @vht_capa: VHT Capability overrides
* @vht_capa_mask: The bits of vht_capa which are to be used.
diff --git a/include/net/mac80211.h b/include/net/mac80211.h
index 5b7a3da..7c5dc78 100644
--- a/include/net/mac80211.h
+++ b/include/net/mac80211.h
@@ -1004,11 +1004,11 @@
* @radar_enabled: whether radar detection is enabled
*
* @long_frame_max_tx_count: Maximum number of transmissions for a "long" frame
- * (a frame not RTS protected), called "dot11LongRetryLimit" in 802.11,
- * but actually means the number of transmissions not the number of retries
+ * (a frame not RTS protected), called "dot11LongRetryLimit" in 802.11,
+ * but actually means the number of transmissions not the number of retries
* @short_frame_max_tx_count: Maximum number of transmissions for a "short"
- * frame, called "dot11ShortRetryLimit" in 802.11, but actually means the
- * number of transmissions not the number of retries
+ * frame, called "dot11ShortRetryLimit" in 802.11, but actually means the
+ * number of transmissions not the number of retries
*
* @smps_mode: spatial multiplexing powersave mode; note that
* %IEEE80211_SMPS_STATIC is used when the device is not
@@ -1092,7 +1092,7 @@
* be off when it is %NULL there can still be races and packets could be
* processed after it switches back to %NULL.
* @debugfs_dir: debugfs dentry, can be used by drivers to create own per
- * interface debug files. Note that it will be NULL for the virtual
+ * interface debug files. Note that it will be NULL for the virtual
* monitor interface (if that is requested.)
* @drv_priv: data area for driver use, will always be aligned to
* sizeof(void *).
@@ -1425,10 +1425,10 @@
* the stack.
*
* @IEEE80211_HW_CONNECTION_MONITOR:
- * The hardware performs its own connection monitoring, including
- * periodic keep-alives to the AP and probing the AP on beacon loss.
- * When this flag is set, signaling beacon-loss will cause an immediate
- * change to disassociated state.
+ * The hardware performs its own connection monitoring, including
+ * periodic keep-alives to the AP and probing the AP on beacon loss.
+ * When this flag is set, signaling beacon-loss will cause an immediate
+ * change to disassociated state.
*
* @IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC:
* This device needs to get data from beacon before association (i.e.
@@ -1526,10 +1526,10 @@
* @channel_change_time: time (in microseconds) it takes to change channels.
*
* @max_signal: Maximum value for signal (rssi) in RX information, used
- * only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB
+ * only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB
*
* @max_listen_interval: max listen interval in units of beacon interval
- * that HW supports
+ * that HW supports
*
* @queues: number of available hardware transmit queues for
* data packets. WMM/QoS requires at least four, these
@@ -2443,7 +2443,7 @@
* The callback can sleep.
*
* @set_tsf: Set the TSF timer to the specified value in the firmware/hardware.
- * Currently, this is only used for IBSS mode debugging. Is not a
+ * Currently, this is only used for IBSS mode debugging. Is not a
* required function.
* The callback can sleep.
*