diff --git a/Documentation/ABI/testing/sysfs-driver-hid-picolcd b/Documentation/ABI/testing/sysfs-driver-hid-picolcd
new file mode 100644
index 0000000..08579e7
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-driver-hid-picolcd
@@ -0,0 +1,43 @@
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/operation_mode
+Date:		March 2010
+Contact:	Bruno Prémont <bonbons@linux-vserver.org>
+Description:	Make it possible to switch the PicoLCD device between LCD
+		(firmware) and bootloader (flasher) operation modes.
+
+		Reading: returns list of available modes, the active mode being
+		enclosed in brackets ('[' and ']')
+
+		Writing: causes operation mode switch. Permitted values are
+		the non-active mode names listed when read.
+
+		Note: when switching mode the current PicoLCD HID device gets
+		disconnected and reconnects after above delay (see attribute
+		operation_mode_delay for its value).
+
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/operation_mode_delay
+Date:		April 2010
+Contact:	Bruno Prémont <bonbons@linux-vserver.org>
+Description:	Delay PicoLCD waits before restarting in new mode when
+		operation_mode has changed.
+
+		Reading/Writing: It is expressed in ms and permitted range is
+		0..30000ms.
+
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/fb_update_rate
+Date:		March 2010
+Contact:	Bruno Prémont <bonbons@linux-vserver.org>
+Description:	Make it possible to adjust defio refresh rate.
+
+		Reading: returns list of available refresh rates (expressed in Hz),
+		the active refresh rate being enclosed in brackets ('[' and ']')
+
+		Writing: accepts new refresh rate expressed in integer Hz
+		within permitted rates.
+
+		Note: As device can barely do 2 complete refreshes a second
+		it only makes sense to adjust this value if only one or two
+		tiles get changed and it's not appropriate to expect the application
+		to flush it's tiny changes explicitely at higher than default rate.
+
diff --git a/Documentation/ABI/testing/sysfs-driver-hid-prodikeys b/Documentation/ABI/testing/sysfs-driver-hid-prodikeys
new file mode 100644
index 0000000..05d988c
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-driver-hid-prodikeys
@@ -0,0 +1,29 @@
+What:		/sys/bus/hid/drivers/prodikeys/.../channel
+Date:		April 2010
+KernelVersion:	2.6.34
+Contact:	Don Prince <dhprince.devel@yahoo.co.uk>
+Description:
+		Allows control (via software) the midi channel to which
+		that the pc-midi keyboard will output.midi data.
+		Range: 0..15
+		Type:  Read/write
+What:		/sys/bus/hid/drivers/prodikeys/.../sustain
+Date:		April 2010
+KernelVersion:	2.6.34
+Contact:	Don Prince <dhprince.devel@yahoo.co.uk>
+Description:
+		Allows control (via software) the sustain duration of a
+		note held by the pc-midi driver.
+		0 means sustain mode is disabled.
+		Range: 0..5000 (milliseconds)
+		Type:  Read/write
+What:		/sys/bus/hid/drivers/prodikeys/.../octave
+Date:		April 2010
+KernelVersion:	2.6.34
+Contact:	Don Prince <dhprince.devel@yahoo.co.uk>
+Description:
+		Controls the octave shift modifier in the pc-midi driver.
+		The octave can be shifted via software up/down 2 octaves.
+		0 means the no ocatve shift.
+		Range: -2..2 (minus 2 to plus 2)
+		Type: Read/Write
diff --git a/Documentation/ABI/testing/sysfs-driver-hid-roccat-kone b/Documentation/ABI/testing/sysfs-driver-hid-roccat-kone
new file mode 100644
index 0000000..88340a2
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-driver-hid-roccat-kone
@@ -0,0 +1,111 @@
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/actual_dpi
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	It is possible to switch the dpi setting of the mouse with the
+		press of a button.
+		When read, this file returns the raw number of the actual dpi
+		setting reported by the mouse. This number has to be further
+		processed to receive the real dpi value.
+
+		VALUE DPI
+		1     800
+		2     1200
+		3     1600
+		4     2000
+		5     2400
+		6     3200
+
+		This file is readonly.
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/actual_profile
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	When read, this file returns the number of the actual profile.
+		This file is readonly.
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/firmware_version
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	When read, this file returns the raw integer version number of the
+		firmware reported by the mouse. Using the integer value eases
+		further usage in other programs. To receive the real version
+		number the decimal point has to be shifted 2 positions to the
+		left. E.g. a returned value of 138 means 1.38
+		This file is readonly.
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/kone_driver_version
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	When read, this file returns the driver version.
+		The format of the string is "v<major>.<minor>.<patchlevel>".
+		This attribute is used by the userland tools to find the sysfs-
+		paths of installed kone-mice and determine the capabilites of
+		the driver. Versions of this driver for old kernels replace
+		usbhid instead of generic-usb. The way to scan for this file
+		has been chosen to provide a consistent way for all supported
+		kernel versions.
+		This file is readonly.
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/profile[1-5]
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	The mouse can store 5 profiles which can be switched by the
+                press of a button. A profile holds informations like button
+                mappings, sensitivity, the colors of the 5 leds and light
+                effects.
+                When read, these files return the respective profile. The
+                returned data is 975 bytes in size.
+		When written, this file lets one write the respective profile
+		data back to the mouse. The data has to be 975 bytes long.
+		The mouse will reject invalid data, whereas the profile number
+		stored in the profile doesn't need to fit the number of the
+		store.
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/settings
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	When read, this file returns the settings stored in the mouse.
+		The size of the data is 36 bytes and holds information like the
+		startup_profile, tcu state and calibration_data.
+		When written, this file lets write settings back to the mouse.
+		The data has to be 36 bytes long. The mouse will reject invalid
+		data.
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/startup_profile
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	The integer value of this attribute ranges from 1 to 5.
+                When read, this attribute returns the number of the profile
+                that's active when the mouse is powered on.
+		When written, this file sets the number of the startup profile
+		and the mouse activates this profile immediately.
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/tcu
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	The mouse has a "Tracking Control Unit" which lets the user
+		calibrate the laser power to fit the mousepad surface.
+		When read, this file returns the current state of the TCU,
+		where 0 means off and 1 means on.
+		Writing 0 in this file will switch the TCU off.
+		Writing 1 in this file will start the calibration which takes
+		around 6 seconds to complete and activates the TCU.
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/weight
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	The mouse can be equipped with one of four supplied weights
+		ranging from 5 to 20 grams which are recognized by the mouse
+		and its value can be read out. When read, this file returns the
+		raw value returned by the mouse which eases further processing
+		in other software.
+		The values map to the weights as follows:
+
+		VALUE WEIGHT
+		0     none
+		1     5g
+		2     10g
+		3     15g
+		4     20g
+
+		This file is readonly.
diff --git a/Documentation/ABI/testing/sysfs-wacom b/Documentation/ABI/testing/sysfs-wacom
new file mode 100644
index 0000000..1517976
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-wacom
@@ -0,0 +1,10 @@
+What:		/sys/class/hidraw/hidraw*/device/speed
+Date:		April 2010
+Kernel Version:	2.6.35
+Contact:	linux-bluetooth@vger.kernel.org
+Description:
+		The /sys/class/hidraw/hidraw*/device/speed file controls
+		reporting speed of wacom bluetooth tablet. Reading from
+		this file returns 1 if tablet reports in high speed mode
+		or 0 otherwise. Writing to this file one of these values
+		switches reporting speed.
diff --git a/drivers/hid/Kconfig b/drivers/hid/Kconfig
index 71d4c07..76ba59b 100644
--- a/drivers/hid/Kconfig
+++ b/drivers/hid/Kconfig
@@ -86,6 +86,12 @@
 	---help---
 	Support for Belkin Flip KVM and Wireless keyboard.
 
+config HID_CANDO
+	tristate "Cando dual touch panel"
+	depends on USB_HID
+	---help---
+	Support for Cando dual touch panel.
+
 config HID_CHERRY
 	tristate "Cherry" if EMBEDDED
 	depends on USB_HID
@@ -100,6 +106,21 @@
 	---help---
 	Support for Chicony Tactical pad.
 
+config HID_PRODIKEYS
+	tristate "Prodikeys PC-MIDI Keyboard support"
+	depends on USB_HID && SND
+	select SND_RAWMIDI
+	---help---
+	Support for Prodikeys PC-MIDI Keyboard device support.
+	Say Y here to enable support for this device.
+	- Prodikeys PC-MIDI keyboard.
+	  The Prodikeys PC-MIDI acts as a USB Audio device, with one MIDI
+	  input and one MIDI output. These MIDI jacks appear as
+	  a sound "card" in the ALSA sound system.
+	  Note: if you say N here, this device will still function as a basic
+	  multimedia keyboard, but will lack support for the musical keyboard
+	  and some additional multimedia keys.
+
 config HID_CYPRESS
 	tristate "Cypress" if EMBEDDED
 	depends on USB_HID
@@ -108,9 +129,8 @@
 	Support for cypress mouse and barcode readers.
 
 config HID_DRAGONRISE
-	tristate "DragonRise Inc. support" if EMBEDDED
+	tristate "DragonRise Inc. support"
 	depends on USB_HID
-	default !EMBEDDED
 	---help---
 	Say Y here if you have DragonRise Inc.game controllers.
 
@@ -122,6 +142,12 @@
 	Say Y here if you want to enable force feedback support for DragonRise Inc.
 	game controllers.
 
+config HID_EGALAX
+	tristate "eGalax multi-touch panel"
+	depends on USB_HID
+	---help---
+	Support for the eGalax dual-touch panel.
+
 config HID_EZKEY
 	tristate "Ezkey" if EMBEDDED
 	depends on USB_HID
@@ -137,16 +163,14 @@
 	Support for Kye/Genius Ergo Mouse.
 
 config HID_GYRATION
-	tristate "Gyration" if EMBEDDED
+	tristate "Gyration"
 	depends on USB_HID
-	default !EMBEDDED
 	---help---
 	Support for Gyration remote control.
 
 config HID_TWINHAN
-	tristate "Twinhan" if EMBEDDED
+	tristate "Twinhan"
 	depends on USB_HID
-	default !EMBEDDED
 	---help---
 	Support for Twinhan IR remote control.
 
@@ -233,16 +257,14 @@
 	Support for N-Trig touch screen.
 
 config HID_ORTEK
-	tristate "Ortek" if EMBEDDED
+	tristate "Ortek"
 	depends on USB_HID
-	default !EMBEDDED
 	---help---
 	Support for Ortek WKB-2000 wireless keyboard + mouse trackpad.
 
 config HID_PANTHERLORD
-	tristate "Pantherlord support" if EMBEDDED
+	tristate "Pantherlord support"
 	depends on USB_HID
-	default !EMBEDDED
 	---help---
 	  Say Y here if you have a PantherLord/GreenAsia based game controller
 	  or adapter.
@@ -256,29 +278,90 @@
 	  or adapter and want to enable force feedback support for it.
 
 config HID_PETALYNX
-	tristate "Petalynx" if EMBEDDED
+	tristate "Petalynx"
 	depends on USB_HID
-	default !EMBEDDED
 	---help---
 	Support for Petalynx Maxter remote control.
 
+config HID_PICOLCD
+	tristate "PicoLCD (graphic version)"
+	depends on USB_HID
+	---help---
+	  This provides support for Minibox PicoLCD devices, currently
+	  only the graphical ones are supported.
+
+	  This includes support for the following device features:
+	  - Keypad
+	  - Switching between Firmware and Flash mode
+	  - EEProm / Flash access     (via debugfs)
+	  Features selectively enabled:
+	  - Framebuffer for monochrome 256x64 display
+	  - Backlight control
+	  - Contrast control
+	  - General purpose outputs
+	  Features that are not (yet) supported:
+	  - IR
+
+config HID_PICOLCD_FB
+	bool "Framebuffer support" if EMBEDDED
+	default !EMBEDDED
+	depends on HID_PICOLCD
+	depends on HID_PICOLCD=FB || FB=y
+	select FB_DEFERRED_IO
+	select FB_SYS_FILLRECT
+	select FB_SYS_COPYAREA
+	select FB_SYS_IMAGEBLIT
+	select FB_SYS_FOPS
+	---help---
+	  Provide access to PicoLCD's 256x64 monochrome display via a
+	  frambuffer device.
+
+config HID_PICOLCD_BACKLIGHT
+	bool "Backlight control" if EMBEDDED
+	default !EMBEDDED
+	depends on HID_PICOLCD
+	depends on HID_PICOLCD=BACKLIGHT_CLASS_DEVICE || BACKLIGHT_CLASS_DEVICE=y
+	---help---
+	  Provide access to PicoLCD's backlight control via backlight
+	  class.
+
+config HID_PICOLCD_LCD
+	bool "Contrast control" if EMBEDDED
+	default !EMBEDDED
+	depends on HID_PICOLCD
+	depends on HID_PICOLCD=LCD_CLASS_DEVICE || LCD_CLASS_DEVICE=y
+	---help---
+	  Provide access to PicoLCD's LCD contrast via lcd class.
+
+config HID_PICOLCD_LEDS
+	bool "GPO via leds class" if EMBEDDED
+	default !EMBEDDED
+	depends on HID_PICOLCD
+	depends on HID_PICOLCD=LEDS_CLASS || LEDS_CLASS=y
+	---help---
+	  Provide access to PicoLCD's GPO pins via leds class.
+
 config HID_QUANTA
 	tristate "Quanta Optical Touch"
 	depends on USB_HID
 	---help---
 	Support for Quanta Optical Touch dual-touch panels.
 
-config HID_SAMSUNG
-	tristate "Samsung" if EMBEDDED
+config HID_ROCCAT_KONE
+	tristate "Roccat Kone Mouse support"
 	depends on USB_HID
-	default !EMBEDDED
 	---help---
-	Support for Samsung InfraRed remote control.
+	Support for Roccat Kone mouse.
+
+config HID_SAMSUNG
+	tristate "Samsung"
+	depends on USB_HID
+	---help---
+	Support for Samsung InfraRed remote control or keyboards.
 
 config HID_SONY
-	tristate "Sony" if EMBEDDED
+	tristate "Sony"
 	depends on USB_HID
-	default !EMBEDDED
 	---help---
 	Support for Sony PS3 controller.
 
@@ -289,16 +372,14 @@
 	Support for Stantum multitouch panel.
 
 config HID_SUNPLUS
-	tristate "Sunplus" if EMBEDDED
+	tristate "Sunplus"
 	depends on USB_HID
-	default !EMBEDDED
 	---help---
 	Support for Sunplus wireless desktop.
 
 config HID_GREENASIA
-	tristate "GreenAsia (Product ID 0x12) support" if EMBEDDED
+	tristate "GreenAsia (Product ID 0x12) support"
 	depends on USB_HID
-	default !EMBEDDED
 	---help---
 	  Say Y here if you have a GreenAsia (Product ID 0x12) based game
 	  controller or adapter.
@@ -313,9 +394,8 @@
 	and want to enable force feedback support for it.
 
 config HID_SMARTJOYPLUS
-	tristate "SmartJoy PLUS PS2/USB adapter support" if EMBEDDED
+	tristate "SmartJoy PLUS PS2/USB adapter support"
 	depends on USB_HID
-	default !EMBEDDED
 	---help---
 	Support for SmartJoy PLUS PS2/USB adapter.
 
@@ -328,16 +408,14 @@
 	enable force feedback support for it.
 
 config HID_TOPSEED
-	tristate "TopSeed Cyberlink remote control support" if EMBEDDED
+	tristate "TopSeed Cyberlink remote control support"
 	depends on USB_HID
-	default !EMBEDDED
 	---help---
-	Say Y if you have a TopSeed Cyberlink remote control.
+	Say Y if you have a TopSeed Cyberlink or BTC Emprex remote control.
 
 config HID_THRUSTMASTER
-	tristate "ThrustMaster devices support" if EMBEDDED
+	tristate "ThrustMaster devices support"
 	depends on USB_HID
-	default !EMBEDDED
 	---help---
 	  Say Y here if you have a THRUSTMASTER FireStore Dual Power 2 or
 	  a THRUSTMASTER Ferrari GT Rumble Wheel.
@@ -357,10 +435,17 @@
 	---help---
 	Support for Wacom Graphire Bluetooth tablet.
 
+config HID_WACOM_POWER_SUPPLY
+	bool "Wacom Bluetooth devices power supply status support"
+	depends on HID_WACOM
+	select POWER_SUPPLY
+	---help---
+	  Say Y here if you want to enable power supply status monitoring for
+	  Wacom Bluetooth devices.
+
 config HID_ZEROPLUS
-	tristate "Zeroplus based game controller support" if EMBEDDED
+	tristate "Zeroplus based game controller support"
 	depends on USB_HID
-	default !EMBEDDED
 	---help---
 	  Say Y here if you have a Zeroplus based game controller.
 
@@ -372,6 +457,12 @@
 	  Say Y here if you have a Zeroplus based game controller and want
 	  to have force feedback support for it.
 
+config HID_ZYDACRON
+	tristate "Zydacron remote control support"
+	depends on USB_HID
+	---help---
+	Support for Zydacron remote control.
+
 endmenu
 
 endif # HID_SUPPORT
diff --git a/drivers/hid/Makefile b/drivers/hid/Makefile
index 0b2618f..22e47eae 100644
--- a/drivers/hid/Makefile
+++ b/drivers/hid/Makefile
@@ -26,10 +26,12 @@
 obj-$(CONFIG_HID_A4TECH)	+= hid-a4tech.o
 obj-$(CONFIG_HID_APPLE)		+= hid-apple.o
 obj-$(CONFIG_HID_BELKIN)	+= hid-belkin.o
+obj-$(CONFIG_HID_CANDO)		+= hid-cando.o
 obj-$(CONFIG_HID_CHERRY)	+= hid-cherry.o
 obj-$(CONFIG_HID_CHICONY)	+= hid-chicony.o
 obj-$(CONFIG_HID_CYPRESS)	+= hid-cypress.o
 obj-$(CONFIG_HID_DRAGONRISE)	+= hid-drff.o
+obj-$(CONFIG_HID_EGALAX)	+= hid-egalax.o
 obj-$(CONFIG_HID_EZKEY)		+= hid-ezkey.o
 obj-$(CONFIG_HID_GYRATION)	+= hid-gyration.o
 obj-$(CONFIG_HID_KENSINGTON)	+= hid-kensington.o
@@ -41,9 +43,12 @@
 obj-$(CONFIG_HID_MOSART)	+= hid-mosart.o
 obj-$(CONFIG_HID_NTRIG)		+= hid-ntrig.o
 obj-$(CONFIG_HID_ORTEK)		+= hid-ortek.o
+obj-$(CONFIG_HID_PRODIKEYS)	+= hid-prodikeys.o
 obj-$(CONFIG_HID_QUANTA)	+= hid-quanta.o
 obj-$(CONFIG_HID_PANTHERLORD)	+= hid-pl.o
 obj-$(CONFIG_HID_PETALYNX)	+= hid-petalynx.o
+obj-$(CONFIG_HID_PICOLCD)	+= hid-picolcd.o
+obj-$(CONFIG_HID_ROCCAT_KONE)	+= hid-roccat-kone.o
 obj-$(CONFIG_HID_SAMSUNG)	+= hid-samsung.o
 obj-$(CONFIG_HID_SMARTJOYPLUS)	+= hid-sjoy.o
 obj-$(CONFIG_HID_SONY)		+= hid-sony.o
@@ -54,6 +59,7 @@
 obj-$(CONFIG_HID_TOPSEED)	+= hid-topseed.o
 obj-$(CONFIG_HID_TWINHAN)	+= hid-twinhan.o
 obj-$(CONFIG_HID_ZEROPLUS)	+= hid-zpff.o
+obj-$(CONFIG_HID_ZYDACRON)	+= hid-zydacron.o
 obj-$(CONFIG_HID_WACOM)		+= hid-wacom.o
 
 obj-$(CONFIG_USB_HID)		+= usbhid/
diff --git a/drivers/hid/hid-3m-pct.c b/drivers/hid/hid-3m-pct.c
index c31e0be..2a0d56b 100644
--- a/drivers/hid/hid-3m-pct.c
+++ b/drivers/hid/hid-3m-pct.c
@@ -1,7 +1,7 @@
 /*
  *  HID driver for 3M PCT multitouch panels
  *
- *  Copyright (c) 2009 Stephane Chatty <chatty@enac.fr>
+ *  Copyright (c) 2009-2010 Stephane Chatty <chatty@enac.fr>
  *
  */
 
@@ -25,7 +25,7 @@
 #include "hid-ids.h"
 
 struct mmm_finger {
-	__s32 x, y;
+	__s32 x, y, w, h;
 	__u8 rank;
 	bool touch, valid;
 };
@@ -82,7 +82,18 @@
 			/* touchscreen emulation */
 			hid_map_usage(hi, usage, bit, max, EV_KEY, BTN_TOUCH);
 			return 1;
+		case HID_DG_WIDTH:
+			hid_map_usage(hi, usage, bit, max,
+					EV_ABS, ABS_MT_TOUCH_MAJOR);
+			return 1;
+		case HID_DG_HEIGHT:
+			hid_map_usage(hi, usage, bit, max,
+					EV_ABS, ABS_MT_TOUCH_MINOR);
+			input_set_abs_params(hi->input, ABS_MT_ORIENTATION,
+					1, 1, 0, 0);
+			return 1;
 		case HID_DG_CONTACTID:
+			field->logical_maximum = 59;
 			hid_map_usage(hi, usage, bit, max,
 					EV_ABS, ABS_MT_TRACKING_ID);
 			return 1;
@@ -128,9 +139,15 @@
 			/* this finger is just placeholder data, ignore */
 		} else if (f->touch) {
 			/* this finger is on the screen */
+			int wide = (f->w > f->h);
 			input_event(input, EV_ABS, ABS_MT_TRACKING_ID, i);
 			input_event(input, EV_ABS, ABS_MT_POSITION_X, f->x);
 			input_event(input, EV_ABS, ABS_MT_POSITION_Y, f->y);
+			input_event(input, EV_ABS, ABS_MT_ORIENTATION, wide);
+			input_event(input, EV_ABS, ABS_MT_TOUCH_MAJOR,
+						wide ? f->w : f->h);
+			input_event(input, EV_ABS, ABS_MT_TOUCH_MINOR,
+						wide ? f->h : f->w);
 			input_mt_sync(input);
 			/*
 			 * touchscreen emulation: maintain the age rank
@@ -197,6 +214,14 @@
 		case HID_DG_CONFIDENCE:
 			md->valid = value;
 			break;
+		case HID_DG_WIDTH:
+			if (md->valid)
+				md->f[md->curid].w = value;
+			break;
+		case HID_DG_HEIGHT:
+			if (md->valid)
+				md->f[md->curid].h = value;
+			break;
 		case HID_DG_CONTACTID:
 			if (md->valid) {
 				md->curid = value;
@@ -255,6 +280,7 @@
 
 static const struct hid_device_id mmm_devices[] = {
 	{ HID_USB_DEVICE(USB_VENDOR_ID_3M, USB_DEVICE_ID_3M1968) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_3M, USB_DEVICE_ID_3M2256) },
 	{ }
 };
 MODULE_DEVICE_TABLE(hid, mmm_devices);
@@ -287,5 +313,4 @@
 
 module_init(mmm_init);
 module_exit(mmm_exit);
-MODULE_LICENSE("GPL");
 
diff --git a/drivers/hid/hid-cando.c b/drivers/hid/hid-cando.c
new file mode 100644
index 0000000..4267a6f
--- /dev/null
+++ b/drivers/hid/hid-cando.c
@@ -0,0 +1,272 @@
+/*
+ *  HID driver for Cando dual-touch panels
+ *
+ *  Copyright (c) 2010 Stephane Chatty <chatty@enac.fr>
+ *
+ */
+
+/*
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ */
+
+#include <linux/device.h>
+#include <linux/hid.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+
+MODULE_AUTHOR("Stephane Chatty <chatty@enac.fr>");
+MODULE_DESCRIPTION("Cando dual-touch panel");
+MODULE_LICENSE("GPL");
+
+#include "hid-ids.h"
+
+struct cando_data {
+	__u16 x, y;
+	__u8 id;
+	__s8 oldest;		/* id of the oldest finger in previous frame */
+	bool valid;		/* valid finger data, or just placeholder? */
+	bool first;		/* is this the first finger in this frame? */
+	__s8 firstid;		/* id of the first finger in the frame */
+	__u16 firstx, firsty;	/* (x, y) of the first finger in the frame */
+};
+
+static int cando_input_mapping(struct hid_device *hdev, struct hid_input *hi,
+		struct hid_field *field, struct hid_usage *usage,
+		unsigned long **bit, int *max)
+{
+	switch (usage->hid & HID_USAGE_PAGE) {
+
+	case HID_UP_GENDESK:
+		switch (usage->hid) {
+		case HID_GD_X:
+			hid_map_usage(hi, usage, bit, max,
+					EV_ABS, ABS_MT_POSITION_X);
+			/* touchscreen emulation */
+			input_set_abs_params(hi->input, ABS_X,
+						field->logical_minimum,
+						field->logical_maximum, 0, 0);
+			return 1;
+		case HID_GD_Y:
+			hid_map_usage(hi, usage, bit, max,
+					EV_ABS, ABS_MT_POSITION_Y);
+			/* touchscreen emulation */
+			input_set_abs_params(hi->input, ABS_Y,
+						field->logical_minimum,
+						field->logical_maximum, 0, 0);
+			return 1;
+		}
+		return 0;
+
+	case HID_UP_DIGITIZER:
+		switch (usage->hid) {
+		case HID_DG_TIPSWITCH:
+		case HID_DG_CONTACTMAX:
+			return -1;
+		case HID_DG_INRANGE:
+			/* touchscreen emulation */
+			hid_map_usage(hi, usage, bit, max, EV_KEY, BTN_TOUCH);
+			return 1;
+		case HID_DG_CONTACTID:
+			hid_map_usage(hi, usage, bit, max,
+					EV_ABS, ABS_MT_TRACKING_ID);
+			return 1;
+		}
+		return 0;
+	}
+
+	return 0;
+}
+
+static int cando_input_mapped(struct hid_device *hdev, struct hid_input *hi,
+		struct hid_field *field, struct hid_usage *usage,
+		unsigned long **bit, int *max)
+{
+	if (usage->type == EV_KEY || usage->type == EV_ABS)
+		clear_bit(usage->code, *bit);
+
+	return 0;
+}
+
+/*
+ * this function is called when a whole finger has been parsed,
+ * so that it can decide what to send to the input layer.
+ */
+static void cando_filter_event(struct cando_data *td, struct input_dev *input)
+{
+	td->first = !td->first; /* touchscreen emulation */
+
+	if (!td->valid) {
+		/*
+		 * touchscreen emulation: if this is the second finger and
+		 * the first was valid, the first was the oldest; if the
+		 * first was not valid and there was a valid finger in the
+		 * previous frame, this is a release.
+		 */
+		if (td->first) {
+			td->firstid = -1;
+		} else if (td->firstid >= 0) {
+			input_event(input, EV_ABS, ABS_X, td->firstx);
+			input_event(input, EV_ABS, ABS_Y, td->firsty);
+			td->oldest = td->firstid;
+		} else if (td->oldest >= 0) {
+			input_event(input, EV_KEY, BTN_TOUCH, 0);
+			td->oldest = -1;
+		}
+
+		return;
+	}
+	
+	input_event(input, EV_ABS, ABS_MT_TRACKING_ID, td->id);
+	input_event(input, EV_ABS, ABS_MT_POSITION_X, td->x);
+	input_event(input, EV_ABS, ABS_MT_POSITION_Y, td->y);
+
+	input_mt_sync(input);
+
+	/*
+	 * touchscreen emulation: if there was no touching finger previously,
+	 * emit touch event
+	 */
+	if (td->oldest < 0) {
+		input_event(input, EV_KEY, BTN_TOUCH, 1);
+		td->oldest = td->id;
+	}
+
+	/*
+	 * touchscreen emulation: if this is the first finger, wait for the
+	 * second; the oldest is then the second if it was the oldest already
+	 * or if there was no first, the first otherwise.
+	 */
+	if (td->first) {
+		td->firstx = td->x;
+		td->firsty = td->y;
+		td->firstid = td->id;
+	} else {
+		int x, y, oldest;
+		if (td->id == td->oldest || td->firstid < 0) {
+			x = td->x;
+			y = td->y;
+			oldest = td->id;
+		} else {
+			x = td->firstx;
+			y = td->firsty;
+			oldest = td->firstid;
+		}
+		input_event(input, EV_ABS, ABS_X, x);
+		input_event(input, EV_ABS, ABS_Y, y);
+		td->oldest = oldest;
+	}
+}
+
+
+static int cando_event(struct hid_device *hid, struct hid_field *field,
+				struct hid_usage *usage, __s32 value)
+{
+	struct cando_data *td = hid_get_drvdata(hid);
+
+	if (hid->claimed & HID_CLAIMED_INPUT) {
+		struct input_dev *input = field->hidinput->input;
+
+		switch (usage->hid) {
+		case HID_DG_INRANGE:
+			td->valid = value;
+			break;
+		case HID_DG_CONTACTID:
+			td->id = value;
+			break;
+		case HID_GD_X:
+			td->x = value;
+			break;
+		case HID_GD_Y:
+			td->y = value;
+			cando_filter_event(td, input);
+			break;
+		case HID_DG_TIPSWITCH:
+			/* avoid interference from generic hidinput handling */
+			break;
+
+		default:
+			/* fallback to the generic hidinput handling */
+			return 0;
+		}
+	}
+
+	/* we have handled the hidinput part, now remains hiddev */
+	if (hid->claimed & HID_CLAIMED_HIDDEV && hid->hiddev_hid_event)
+		hid->hiddev_hid_event(hid, field, usage, value);
+
+	return 1;
+}
+
+static int cando_probe(struct hid_device *hdev, const struct hid_device_id *id)
+{
+	int ret;
+	struct cando_data *td;
+
+	td = kmalloc(sizeof(struct cando_data), GFP_KERNEL);
+	if (!td) {
+		dev_err(&hdev->dev, "cannot allocate Cando Touch data\n");
+		return -ENOMEM;
+	}
+	hid_set_drvdata(hdev, td);
+	td->first = false;
+	td->oldest = -1;
+	td->valid = false;
+
+	ret = hid_parse(hdev);
+	if (!ret)
+		ret = hid_hw_start(hdev, HID_CONNECT_DEFAULT);
+
+	if (ret)
+		kfree(td);
+
+	return ret;
+}
+
+static void cando_remove(struct hid_device *hdev)
+{
+	hid_hw_stop(hdev);
+	kfree(hid_get_drvdata(hdev));
+	hid_set_drvdata(hdev, NULL);
+}
+
+static const struct hid_device_id cando_devices[] = {
+	{ HID_USB_DEVICE(USB_VENDOR_ID_CANDO,
+			USB_DEVICE_ID_CANDO_MULTI_TOUCH) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_CANDO,
+			USB_DEVICE_ID_CANDO_MULTI_TOUCH_11_6) },
+	{ }
+};
+MODULE_DEVICE_TABLE(hid, cando_devices);
+
+static const struct hid_usage_id cando_grabbed_usages[] = {
+	{ HID_ANY_ID, HID_ANY_ID, HID_ANY_ID },
+	{ HID_ANY_ID - 1, HID_ANY_ID - 1, HID_ANY_ID - 1}
+};
+
+static struct hid_driver cando_driver = {
+	.name = "cando-touch",
+	.id_table = cando_devices,
+	.probe = cando_probe,
+	.remove = cando_remove,
+	.input_mapping = cando_input_mapping,
+	.input_mapped = cando_input_mapped,
+	.usage_table = cando_grabbed_usages,
+	.event = cando_event,
+};
+
+static int __init cando_init(void)
+{
+	return hid_register_driver(&cando_driver);
+}
+
+static void __exit cando_exit(void)
+{
+	hid_unregister_driver(&cando_driver);
+}
+
+module_init(cando_init);
+module_exit(cando_exit);
+
diff --git a/drivers/hid/hid-core.c b/drivers/hid/hid-core.c
index 143e788..e10e314 100644
--- a/drivers/hid/hid-core.c
+++ b/drivers/hid/hid-core.c
@@ -653,10 +653,9 @@
 	if (device->driver->report_fixup)
 		device->driver->report_fixup(device, start, size);
 
-	device->rdesc = kmalloc(size, GFP_KERNEL);
+	device->rdesc = kmemdup(start, size, GFP_KERNEL);
 	if (device->rdesc == NULL)
 		return -ENOMEM;
-	memcpy(device->rdesc, start, size);
 	device->rsize = size;
 
 	parser = vmalloc(sizeof(struct hid_parser));
@@ -940,13 +939,8 @@
 	unsigned count = field->report_count;
 	unsigned offset = field->report_offset;
 	unsigned size = field->report_size;
-	unsigned bitsused = offset + count * size;
 	unsigned n;
 
-	/* make sure the unused bits in the last byte are zeros */
-	if (count > 0 && size > 0 && (bitsused % 8) != 0)
-		data[(bitsused-1)/8] &= (1 << (bitsused % 8)) - 1;
-
 	for (n = 0; n < count; n++) {
 		if (field->logical_minimum < 0)	/* signed values */
 			implement(data, offset + n * size, size, s32ton(field->value[n], size));
@@ -966,6 +960,7 @@
 	if (report->id > 0)
 		*data++ = report->id;
 
+	memset(data, 0, ((report->size - 1) >> 3) + 1);
 	for (n = 0; n < report->maxfield; n++)
 		hid_output_field(report->field[n], data);
 }
@@ -1086,35 +1081,28 @@
 
 	buf = kmalloc(sizeof(char) * HID_DEBUG_BUFSIZE, GFP_ATOMIC);
 
-	if (!buf) {
-		report = hid_get_report(report_enum, data);
+	if (!buf)
 		goto nomem;
-	}
-
-	snprintf(buf, HID_DEBUG_BUFSIZE - 1,
-			"\nreport (size %u) (%snumbered)\n", size, report_enum->numbered ? "" : "un");
-	hid_debug_event(hid, buf);
-
-	report = hid_get_report(report_enum, data);
-	if (!report) {
-		kfree(buf);
-		return -1;
-	}
 
 	/* dump the report */
 	snprintf(buf, HID_DEBUG_BUFSIZE - 1,
-			"report %d (size %u) = ", report->id, size);
+			"\nreport (size %u) (%snumbered) = ", size, report_enum->numbered ? "" : "un");
 	hid_debug_event(hid, buf);
+
 	for (i = 0; i < size; i++) {
 		snprintf(buf, HID_DEBUG_BUFSIZE - 1,
 				" %02x", data[i]);
 		hid_debug_event(hid, buf);
 	}
 	hid_debug_event(hid, "\n");
-
 	kfree(buf);
 
 nomem:
+	report = hid_get_report(report_enum, data);
+
+	if (!report)
+		return -1;
+
 	if (hdrv && hdrv->raw_event && hid_match_report(hid, report)) {
 		ret = hdrv->raw_event(hid, report, data, size);
 		if (ret != 0)
@@ -1167,6 +1155,8 @@
 	unsigned int i;
 	int len;
 
+	if (hdev->quirks & HID_QUIRK_HIDDEV_FORCE)
+		connect_mask |= (HID_CONNECT_HIDDEV_FORCE | HID_CONNECT_HIDDEV);
 	if (hdev->bus != BUS_USB)
 		connect_mask &= ~HID_CONNECT_HIDDEV;
 	if (hid_hiddev(hdev))
@@ -1246,6 +1236,7 @@
 /* a list of devices for which there is a specialized driver on HID bus */
 static const struct hid_device_id hid_blacklist[] = {
 	{ HID_USB_DEVICE(USB_VENDOR_ID_3M, USB_DEVICE_ID_3M1968) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_3M, USB_DEVICE_ID_3M2256) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_A4TECH, USB_DEVICE_ID_A4TECH_WCP32PU) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_A4TECH, USB_DEVICE_ID_A4TECH_X5_005D) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_ATV_IRCONTROL) },
@@ -1290,14 +1281,19 @@
 	{ HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_FOUNTAIN_TP_ONLY) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_GEYSER1_TP_ONLY) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_BELKIN, USB_DEVICE_ID_FLIP_KVM) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_BTC, USB_DEVICE_ID_BTC_EMPREX_REMOTE) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_CANDO, USB_DEVICE_ID_CANDO_MULTI_TOUCH) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_CANDO, USB_DEVICE_ID_CANDO_MULTI_TOUCH_11_6) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_CHERRY, USB_DEVICE_ID_CHERRY_CYMOTION) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_CHERRY, USB_DEVICE_ID_CHERRY_CYMOTION_SOLAR) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_CHICONY, USB_DEVICE_ID_CHICONY_TACTICAL_PAD) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_CREATIVELABS, USB_DEVICE_ID_PRODIKEYS_PCMIDI) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_CYPRESS, USB_DEVICE_ID_CYPRESS_BARCODE_1) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_CYPRESS, USB_DEVICE_ID_CYPRESS_BARCODE_2) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_CYPRESS, USB_DEVICE_ID_CYPRESS_BARCODE_3) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_CYPRESS, USB_DEVICE_ID_CYPRESS_MOUSE) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_DRAGONRISE, 0x0006) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_DWAV, USB_DEVICE_ID_DWAV_EGALAX_MULTITOUCH) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_EZKEY, USB_DEVICE_ID_BTC_8193) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_GAMERON, USB_DEVICE_ID_GAMERON_DUAL_PSX_ADAPTOR) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_GAMERON, USB_DEVICE_ID_GAMERON_DUAL_PCS_ADAPTOR) },
@@ -1331,6 +1327,8 @@
 	{ HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_LOGITECH_RUMBLEPAD2) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_SPACETRAVELLER) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_SPACENAVIGATOR) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_PICOLCD) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_PICOLCD_BOOTLOADER) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_SIDEWINDER_GV) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_NE4K) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_LK6K) },
@@ -1342,7 +1340,9 @@
 	{ HID_USB_DEVICE(USB_VENDOR_ID_PETALYNX, USB_DEVICE_ID_PETALYNX_MAXTER_REMOTE) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_QUANTA, USB_DEVICE_ID_QUANTA_OPTICAL_TOUCH) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_QUANTA, USB_DEVICE_ID_PIXART_IMAGING_INC_OPTICAL_TOUCH_SCREEN) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_ROCCAT, USB_DEVICE_ID_ROCCAT_KONE) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_SAMSUNG, USB_DEVICE_ID_SAMSUNG_IR_REMOTE) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_SAMSUNG, USB_DEVICE_ID_SAMSUNG_WIRELESS_KBD_MOUSE) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_SONY, USB_DEVICE_ID_SONY_PS3_CONTROLLER) },
 	{ HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_SONY, USB_DEVICE_ID_SONY_PS3_CONTROLLER) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_SONY, USB_DEVICE_ID_SONY_VAIO_VGX_MOUSE) },
@@ -1359,8 +1359,10 @@
 	{ HID_USB_DEVICE(USB_VENDOR_ID_TWINHAN, USB_DEVICE_ID_TWINHAN_IR_REMOTE) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_WISEGROUP, USB_DEVICE_ID_SMARTJOY_PLUS) },
 	{ HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_WACOM, USB_DEVICE_ID_WACOM_GRAPHIRE_BLUETOOTH) },
+	{ HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_WACOM, USB_DEVICE_ID_WACOM_INTUOS4_BLUETOOTH) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_ZEROPLUS, 0x0005) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_ZEROPLUS, 0x0030) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_ZYDACRON, USB_DEVICE_ID_ZYDACRON_REMOTE_CONTROL) },
 
 	{ HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_PRESENTER_8K_BT) },
 	{ }
@@ -1757,7 +1759,7 @@
 
 	/* we need to kill them here, otherwise they will stay allocated to
 	 * wait for coming driver */
-	if (hid_ignore(hdev))
+	if (!(hdev->quirks & HID_QUIRK_NO_IGNORE) && hid_ignore(hdev))
 		return -ENODEV;
 
 	/* XXX hack, any other cleaner solution after the driver core
@@ -1765,11 +1767,12 @@
 	dev_set_name(&hdev->dev, "%04X:%04X:%04X.%04X", hdev->bus,
 		     hdev->vendor, hdev->product, atomic_inc_return(&id));
 
+	hid_debug_register(hdev, dev_name(&hdev->dev));
 	ret = device_add(&hdev->dev);
 	if (!ret)
 		hdev->status |= HID_STAT_ADDED;
-
-	hid_debug_register(hdev, dev_name(&hdev->dev));
+	else
+		hid_debug_unregister(hdev);
 
 	return ret;
 }
diff --git a/drivers/hid/hid-egalax.c b/drivers/hid/hid-egalax.c
new file mode 100644
index 0000000..f44bdc0
--- /dev/null
+++ b/drivers/hid/hid-egalax.c
@@ -0,0 +1,281 @@
+/*
+ *  HID driver for eGalax dual-touch panels
+ *
+ *  Copyright (c) 2010 Stephane Chatty <chatty@enac.fr>
+ *
+ */
+
+/*
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ */
+
+#include <linux/device.h>
+#include <linux/hid.h>
+#include <linux/module.h>
+#include <linux/usb.h>
+#include <linux/slab.h>
+#include "usbhid/usbhid.h"
+
+MODULE_AUTHOR("Stephane Chatty <chatty@enac.fr>");
+MODULE_DESCRIPTION("eGalax dual-touch panel");
+MODULE_LICENSE("GPL");
+
+#include "hid-ids.h"
+
+struct egalax_data {
+	__u16 x, y, z;
+	__u8 id;
+	bool first;		/* is this the first finger in the frame? */
+	bool valid;		/* valid finger data, or just placeholder? */
+	bool activity;		/* at least one active finger previously? */
+	__u16 lastx, lasty;	/* latest valid (x, y) in the frame */
+};
+
+static int egalax_input_mapping(struct hid_device *hdev, struct hid_input *hi,
+		struct hid_field *field, struct hid_usage *usage,
+		unsigned long **bit, int *max)
+{
+	switch (usage->hid & HID_USAGE_PAGE) {
+
+	case HID_UP_GENDESK:
+		switch (usage->hid) {
+		case HID_GD_X:
+			hid_map_usage(hi, usage, bit, max,
+					EV_ABS, ABS_MT_POSITION_X);
+			/* touchscreen emulation */
+			input_set_abs_params(hi->input, ABS_X,
+						field->logical_minimum,
+						field->logical_maximum, 0, 0);
+			return 1;
+		case HID_GD_Y:
+			hid_map_usage(hi, usage, bit, max,
+					EV_ABS, ABS_MT_POSITION_Y);
+			/* touchscreen emulation */
+			input_set_abs_params(hi->input, ABS_Y,
+						field->logical_minimum,
+						field->logical_maximum, 0, 0);
+			return 1;
+		}
+		return 0;
+
+	case HID_UP_DIGITIZER:
+		switch (usage->hid) {
+		case HID_DG_TIPSWITCH:
+			/* touchscreen emulation */
+			hid_map_usage(hi, usage, bit, max, EV_KEY, BTN_TOUCH);
+			return 1;
+		case HID_DG_INRANGE:
+		case HID_DG_CONFIDENCE:
+		case HID_DG_CONTACTCOUNT:
+		case HID_DG_CONTACTMAX:
+			return -1;
+		case HID_DG_CONTACTID:
+			hid_map_usage(hi, usage, bit, max,
+					EV_ABS, ABS_MT_TRACKING_ID);
+			return 1;
+		case HID_DG_TIPPRESSURE:
+			hid_map_usage(hi, usage, bit, max,
+					EV_ABS, ABS_MT_PRESSURE);
+			return 1;
+		}
+		return 0;
+	}
+
+	/* ignore others (from other reports we won't get anyway) */
+	return -1;
+}
+
+static int egalax_input_mapped(struct hid_device *hdev, struct hid_input *hi,
+		struct hid_field *field, struct hid_usage *usage,
+		unsigned long **bit, int *max)
+{
+	if (usage->type == EV_KEY || usage->type == EV_ABS)
+		clear_bit(usage->code, *bit);
+
+	return 0;
+}
+
+/*
+ * this function is called when a whole finger has been parsed,
+ * so that it can decide what to send to the input layer.
+ */
+static void egalax_filter_event(struct egalax_data *td, struct input_dev *input)
+{
+	td->first = !td->first; /* touchscreen emulation */
+
+	if (td->valid) {
+		/* emit multitouch events */
+		input_event(input, EV_ABS, ABS_MT_TRACKING_ID, td->id);
+		input_event(input, EV_ABS, ABS_MT_POSITION_X, td->x);
+		input_event(input, EV_ABS, ABS_MT_POSITION_Y, td->y);
+		input_event(input, EV_ABS, ABS_MT_PRESSURE, td->z);
+
+		input_mt_sync(input);
+
+		/*
+		 * touchscreen emulation: store (x, y) as
+		 * the last valid values in this frame
+		 */
+		td->lastx = td->x;
+		td->lasty = td->y;
+	}
+
+	/*
+	 * touchscreen emulation: if this is the second finger and at least
+	 * one in this frame is valid, the latest valid in the frame is
+	 * the oldest on the panel, the one we want for single touch
+	 */
+	if (!td->first && td->activity) {
+		input_event(input, EV_ABS, ABS_X, td->lastx);
+		input_event(input, EV_ABS, ABS_Y, td->lasty);
+	}
+
+	if (!td->valid) {
+		/*
+		 * touchscreen emulation: if the first finger is invalid
+		 * and there previously was finger activity, this is a release
+		 */ 
+		if (td->first && td->activity) {
+			input_event(input, EV_KEY, BTN_TOUCH, 0);
+			td->activity = false;
+		}
+		return;
+	}
+
+
+	/* touchscreen emulation: if no previous activity, emit touch event */
+	if (!td->activity) {
+		input_event(input, EV_KEY, BTN_TOUCH, 1);
+		td->activity = true;
+	}
+}
+
+
+static int egalax_event(struct hid_device *hid, struct hid_field *field,
+				struct hid_usage *usage, __s32 value)
+{
+	struct egalax_data *td = hid_get_drvdata(hid);
+
+	if (hid->claimed & HID_CLAIMED_INPUT) {
+		struct input_dev *input = field->hidinput->input;
+
+		switch (usage->hid) {
+		case HID_DG_INRANGE:
+		case HID_DG_CONFIDENCE:
+			/* avoid interference from generic hidinput handling */
+			break;
+		case HID_DG_TIPSWITCH:
+			td->valid = value;
+			break;
+		case HID_DG_TIPPRESSURE:
+			td->z = value;
+			break;
+		case HID_DG_CONTACTID:
+			td->id = value;
+			break;
+		case HID_GD_X:
+			td->x = value;
+			break;
+		case HID_GD_Y:
+			td->y = value;
+			/* this is the last field in a finger */
+			egalax_filter_event(td, input);
+			break;
+		case HID_DG_CONTACTCOUNT:
+			/* touch emulation: this is the last field in a frame */
+			td->first = false;
+			break;
+
+		default:
+			/* fallback to the generic hidinput handling */
+			return 0;
+		}
+	}
+
+	/* we have handled the hidinput part, now remains hiddev */
+	if (hid->claimed & HID_CLAIMED_HIDDEV && hid->hiddev_hid_event)
+		hid->hiddev_hid_event(hid, field, usage, value);
+
+	return 1;
+}
+
+static int egalax_probe(struct hid_device *hdev, const struct hid_device_id *id)
+{
+	int ret;
+	struct egalax_data *td;
+	struct hid_report *report;
+
+	td = kmalloc(sizeof(struct egalax_data), GFP_KERNEL);
+	if (!td) {
+		dev_err(&hdev->dev, "cannot allocate eGalax data\n");
+		return -ENOMEM;
+	}
+	hid_set_drvdata(hdev, td);
+
+	ret = hid_parse(hdev);
+	if (ret)
+		goto end;
+
+	ret = hid_hw_start(hdev, HID_CONNECT_DEFAULT);
+	if (ret)
+		goto end;
+
+	report = hdev->report_enum[HID_FEATURE_REPORT].report_id_hash[5]; 
+	if (report) {
+		report->field[0]->value[0] = 2;
+		usbhid_submit_report(hdev, report, USB_DIR_OUT);
+	}
+
+end:
+	if (ret)
+		kfree(td);
+
+	return ret;
+}
+
+static void egalax_remove(struct hid_device *hdev)
+{
+	hid_hw_stop(hdev);
+	kfree(hid_get_drvdata(hdev));
+	hid_set_drvdata(hdev, NULL);
+}
+
+static const struct hid_device_id egalax_devices[] = {
+	{ HID_USB_DEVICE(USB_VENDOR_ID_DWAV,
+			USB_DEVICE_ID_DWAV_EGALAX_MULTITOUCH) },
+	{ }
+};
+MODULE_DEVICE_TABLE(hid, egalax_devices);
+
+static const struct hid_usage_id egalax_grabbed_usages[] = {
+	{ HID_ANY_ID, HID_ANY_ID, HID_ANY_ID },
+	{ HID_ANY_ID - 1, HID_ANY_ID - 1, HID_ANY_ID - 1}
+};
+
+static struct hid_driver egalax_driver = {
+	.name = "egalax-touch",
+	.id_table = egalax_devices,
+	.probe = egalax_probe,
+	.remove = egalax_remove,
+	.input_mapping = egalax_input_mapping,
+	.input_mapped = egalax_input_mapped,
+	.usage_table = egalax_grabbed_usages,
+	.event = egalax_event,
+};
+
+static int __init egalax_init(void)
+{
+	return hid_register_driver(&egalax_driver);
+}
+
+static void __exit egalax_exit(void)
+{
+	hid_unregister_driver(&egalax_driver);
+}
+
+module_init(egalax_init);
+module_exit(egalax_exit);
+
diff --git a/drivers/hid/hid-ids.h b/drivers/hid/hid-ids.h
index 09d2764..9776896 100644
--- a/drivers/hid/hid-ids.h
+++ b/drivers/hid/hid-ids.h
@@ -20,6 +20,7 @@
 
 #define USB_VENDOR_ID_3M		0x0596
 #define USB_DEVICE_ID_3M1968		0x0500
+#define USB_DEVICE_ID_3M2256		0x0502
 
 #define USB_VENDOR_ID_A4TECH		0x09da
 #define USB_DEVICE_ID_A4TECH_WCP32PU	0x0006
@@ -123,6 +124,13 @@
 #define USB_VENDOR_ID_BERKSHIRE		0x0c98
 #define USB_DEVICE_ID_BERKSHIRE_PCWD	0x1140
 
+#define USB_VENDOR_ID_BTC		0x046e
+#define USB_DEVICE_ID_BTC_EMPREX_REMOTE	0x5578
+
+#define USB_VENDOR_ID_CANDO		0x2087
+#define USB_DEVICE_ID_CANDO_MULTI_TOUCH 0x0a01
+#define USB_DEVICE_ID_CANDO_MULTI_TOUCH_11_6 0x0b03
+
 #define USB_VENDOR_ID_CH		0x068e
 #define USB_DEVICE_ID_CH_PRO_PEDALS	0x00f2
 #define USB_DEVICE_ID_CH_COMBATSTICK	0x00f4
@@ -148,6 +156,9 @@
 #define USB_DEVICE_ID_CODEMERCS_IOW_FIRST	0x1500
 #define USB_DEVICE_ID_CODEMERCS_IOW_LAST	0x15ff
 
+#define USB_VENDOR_ID_CREATIVELABS	0x041e
+#define USB_DEVICE_ID_PRODIKEYS_PCMIDI	0x2801
+
 #define USB_VENDOR_ID_CYGNAL		0x10c4
 #define USB_DEVICE_ID_CYGNAL_RADIO_SI470X	0x818a
 
@@ -171,6 +182,10 @@
 
 #define USB_VENDOR_ID_DRAGONRISE	0x0079
 
+#define USB_VENDOR_ID_DWAV		0x0eef
+#define USB_DEVICE_ID_EGALAX_TOUCHCONTROLLER	0x0001
+#define USB_DEVICE_ID_DWAV_EGALAX_MULTITOUCH	0x480d
+
 #define USB_VENDOR_ID_ELO		0x04E7
 #define USB_DEVICE_ID_ELO_TS2700	0x0020
 
@@ -342,6 +357,8 @@
 #define USB_VENDOR_ID_MICROCHIP		0x04d8
 #define USB_DEVICE_ID_PICKIT1		0x0032
 #define USB_DEVICE_ID_PICKIT2		0x0033
+#define USB_DEVICE_ID_PICOLCD		0xc002
+#define USB_DEVICE_ID_PICOLCD_BOOTLOADER	0xf002
 
 #define USB_VENDOR_ID_MICROSOFT		0x045e
 #define USB_DEVICE_ID_SIDEWINDER_GV	0x003b
@@ -400,6 +417,9 @@
 #define USB_VENDOR_ID_PRODIGE		0x05af
 #define USB_DEVICE_ID_PRODIGE_CORDLESS	0x3062
 
+#define USB_VENDOR_ID_ROCCAT		0x1e7d
+#define USB_DEVICE_ID_ROCCAT_KONE	0x2ced
+
 #define USB_VENDOR_ID_SAITEK		0x06a3
 #define USB_DEVICE_ID_SAITEK_RUMBLEPAD	0xff17
 
@@ -409,6 +429,7 @@
 
 #define USB_VENDOR_ID_SAMSUNG		0x0419
 #define USB_DEVICE_ID_SAMSUNG_IR_REMOTE	0x0001
+#define USB_DEVICE_ID_SAMSUNG_WIRELESS_KBD_MOUSE	0x0600
 
 #define USB_VENDOR_ID_SONY			0x054c
 #define USB_DEVICE_ID_SONY_VAIO_VGX_MOUSE	0x024b
@@ -457,6 +478,7 @@
 
 #define USB_VENDOR_ID_WACOM		0x056a
 #define USB_DEVICE_ID_WACOM_GRAPHIRE_BLUETOOTH	0x81
+#define USB_DEVICE_ID_WACOM_INTUOS4_BLUETOOTH	0xbd
 
 #define USB_VENDOR_ID_WISEGROUP		0x0925
 #define USB_DEVICE_ID_SMARTJOY_PLUS	0x0005
@@ -475,6 +497,9 @@
 
 #define USB_VENDOR_ID_ZEROPLUS		0x0c12
 
+#define USB_VENDOR_ID_ZYDACRON	0x13EC
+#define USB_DEVICE_ID_ZYDACRON_REMOTE_CONTROL	0x0006
+
 #define USB_VENDOR_ID_KYE		0x0458
 #define USB_DEVICE_ID_KYE_ERGO_525V	0x0087
 #define USB_DEVICE_ID_KYE_GPEN_560	0x5003
diff --git a/drivers/hid/hid-lg.c b/drivers/hid/hid-lg.c
index 3677c90..f6433d8 100644
--- a/drivers/hid/hid-lg.c
+++ b/drivers/hid/hid-lg.c
@@ -126,6 +126,9 @@
 	case 0x1004: lg_map_key_clear(KEY_VIDEO);		break;
 	case 0x1005: lg_map_key_clear(KEY_AUDIO);		break;
 	case 0x100a: lg_map_key_clear(KEY_DOCUMENTS);		break;
+	/* The following two entries are Playlist 1 and 2 on the MX3200 */
+	case 0x100f: lg_map_key_clear(KEY_FN_1);		break;
+	case 0x1010: lg_map_key_clear(KEY_FN_2);		break;
 	case 0x1011: lg_map_key_clear(KEY_PREVIOUSSONG);	break;
 	case 0x1012: lg_map_key_clear(KEY_NEXTSONG);		break;
 	case 0x1013: lg_map_key_clear(KEY_CAMERA);		break;
@@ -137,6 +140,7 @@
 	case 0x1019: lg_map_key_clear(KEY_PROG1);		break;
 	case 0x101a: lg_map_key_clear(KEY_PROG2);		break;
 	case 0x101b: lg_map_key_clear(KEY_PROG3);		break;
+	case 0x101c: lg_map_key_clear(KEY_CYCLEWINDOWS);	break;
 	case 0x101f: lg_map_key_clear(KEY_ZOOMIN);		break;
 	case 0x1020: lg_map_key_clear(KEY_ZOOMOUT);		break;
 	case 0x1021: lg_map_key_clear(KEY_ZOOMRESET);		break;
@@ -147,6 +151,11 @@
 	case 0x1029: lg_map_key_clear(KEY_SHUFFLE);		break;
 	case 0x102a: lg_map_key_clear(KEY_BACK);		break;
 	case 0x102b: lg_map_key_clear(KEY_CYCLEWINDOWS);	break;
+	case 0x102d: lg_map_key_clear(KEY_WWW);			break;
+	/* The following two are 'Start/answer call' and 'End/reject call'
+	   on the MX3200 */
+	case 0x1031: lg_map_key_clear(KEY_OK);			break;
+	case 0x1032: lg_map_key_clear(KEY_CANCEL);		break;
 	case 0x1041: lg_map_key_clear(KEY_BATTERY);		break;
 	case 0x1042: lg_map_key_clear(KEY_WORDPROCESSOR);	break;
 	case 0x1043: lg_map_key_clear(KEY_SPREADSHEET);		break;
diff --git a/drivers/hid/hid-magicmouse.c b/drivers/hid/hid-magicmouse.c
index 0d471fc2..f10d56a 100644
--- a/drivers/hid/hid-magicmouse.c
+++ b/drivers/hid/hid-magicmouse.c
@@ -354,12 +354,15 @@
 		goto err_free;
 	}
 
-	ret = hid_hw_start(hdev, HID_CONNECT_DEFAULT & ~HID_CONNECT_HIDINPUT);
+	ret = hid_hw_start(hdev, HID_CONNECT_DEFAULT);
 	if (ret) {
 		dev_err(&hdev->dev, "magicmouse hw start failed\n");
 		goto err_free;
 	}
 
+	/* we are handling the input ourselves */
+	hidinput_disconnect(hdev);
+
 	report = hid_register_report(hdev, HID_INPUT_REPORT, TOUCH_REPORT_ID);
 	if (!report) {
 		dev_err(&hdev->dev, "unable to register touch report\n");
diff --git a/drivers/hid/hid-ntrig.c b/drivers/hid/hid-ntrig.c
index 4777bbf..b6b0cae 100644
--- a/drivers/hid/hid-ntrig.c
+++ b/drivers/hid/hid-ntrig.c
@@ -24,6 +24,34 @@
 
 #define NTRIG_DUPLICATE_USAGES	0x001
 
+static unsigned int min_width;
+module_param(min_width, uint, 0644);
+MODULE_PARM_DESC(min_width, "Minimum touch contact width to accept.");
+
+static unsigned int min_height;
+module_param(min_height, uint, 0644);
+MODULE_PARM_DESC(min_height, "Minimum touch contact height to accept.");
+
+static unsigned int activate_slack = 1;
+module_param(activate_slack, uint, 0644);
+MODULE_PARM_DESC(activate_slack, "Number of touch frames to ignore at "
+		 "the start of touch input.");
+
+static unsigned int deactivate_slack = 4;
+module_param(deactivate_slack, uint, 0644);
+MODULE_PARM_DESC(deactivate_slack, "Number of empty frames to ignore before "
+		 "deactivating touch.");
+
+static unsigned int activation_width = 64;
+module_param(activation_width, uint, 0644);
+MODULE_PARM_DESC(activation_width, "Width threshold to immediately start "
+		 "processing touch events.");
+
+static unsigned int activation_height = 32;
+module_param(activation_height, uint, 0644);
+MODULE_PARM_DESC(activation_height, "Height threshold to immediately start "
+		 "processing touch events.");
+
 struct ntrig_data {
 	/* Incoming raw values for a single contact */
 	__u16 x, y, w, h;
@@ -37,6 +65,309 @@
 
 	__u8 mt_footer[4];
 	__u8 mt_foot_count;
+
+	/* The current activation state. */
+	__s8 act_state;
+
+	/* Empty frames to ignore before recognizing the end of activity */
+	__s8 deactivate_slack;
+
+	/* Frames to ignore before acknowledging the start of activity */
+	__s8 activate_slack;
+
+	/* Minimum size contact to accept */
+	__u16 min_width;
+	__u16 min_height;
+
+	/* Threshold to override activation slack */
+	__u16 activation_width;
+	__u16 activation_height;
+
+	__u16 sensor_logical_width;
+	__u16 sensor_logical_height;
+	__u16 sensor_physical_width;
+	__u16 sensor_physical_height;
+};
+
+
+static ssize_t show_phys_width(struct device *dev,
+			       struct device_attribute *attr,
+			       char *buf)
+{
+	struct hid_device *hdev = container_of(dev, struct hid_device, dev);
+	struct ntrig_data *nd = hid_get_drvdata(hdev);
+
+	return sprintf(buf, "%d\n", nd->sensor_physical_width);
+}
+
+static DEVICE_ATTR(sensor_physical_width, S_IRUGO, show_phys_width, NULL);
+
+static ssize_t show_phys_height(struct device *dev,
+				struct device_attribute *attr,
+				char *buf)
+{
+	struct hid_device *hdev = container_of(dev, struct hid_device, dev);
+	struct ntrig_data *nd = hid_get_drvdata(hdev);
+
+	return sprintf(buf, "%d\n", nd->sensor_physical_height);
+}
+
+static DEVICE_ATTR(sensor_physical_height, S_IRUGO, show_phys_height, NULL);
+
+static ssize_t show_log_width(struct device *dev,
+			      struct device_attribute *attr,
+			      char *buf)
+{
+	struct hid_device *hdev = container_of(dev, struct hid_device, dev);
+	struct ntrig_data *nd = hid_get_drvdata(hdev);
+
+	return sprintf(buf, "%d\n", nd->sensor_logical_width);
+}
+
+static DEVICE_ATTR(sensor_logical_width, S_IRUGO, show_log_width, NULL);
+
+static ssize_t show_log_height(struct device *dev,
+			       struct device_attribute *attr,
+			       char *buf)
+{
+	struct hid_device *hdev = container_of(dev, struct hid_device, dev);
+	struct ntrig_data *nd = hid_get_drvdata(hdev);
+
+	return sprintf(buf, "%d\n", nd->sensor_logical_height);
+}
+
+static DEVICE_ATTR(sensor_logical_height, S_IRUGO, show_log_height, NULL);
+
+static ssize_t show_min_width(struct device *dev,
+			      struct device_attribute *attr,
+			      char *buf)
+{
+	struct hid_device *hdev = container_of(dev, struct hid_device, dev);
+	struct ntrig_data *nd = hid_get_drvdata(hdev);
+
+	return sprintf(buf, "%d\n", nd->min_width *
+				    nd->sensor_physical_width /
+				    nd->sensor_logical_width);
+}
+
+static ssize_t set_min_width(struct device *dev,
+			     struct device_attribute *attr,
+			     const char *buf, size_t count)
+{
+	struct hid_device *hdev = container_of(dev, struct hid_device, dev);
+	struct ntrig_data *nd = hid_get_drvdata(hdev);
+
+	unsigned long val;
+
+	if (strict_strtoul(buf, 0, &val))
+		return -EINVAL;
+
+	if (val > nd->sensor_physical_width)
+		return -EINVAL;
+
+	nd->min_width = val * nd->sensor_logical_width /
+			      nd->sensor_physical_width;
+
+	return count;
+}
+
+static DEVICE_ATTR(min_width, S_IWUSR | S_IRUGO, show_min_width, set_min_width);
+
+static ssize_t show_min_height(struct device *dev,
+			       struct device_attribute *attr,
+			       char *buf)
+{
+	struct hid_device *hdev = container_of(dev, struct hid_device, dev);
+	struct ntrig_data *nd = hid_get_drvdata(hdev);
+
+	return sprintf(buf, "%d\n", nd->min_height *
+				    nd->sensor_physical_height /
+				    nd->sensor_logical_height);
+}
+
+static ssize_t set_min_height(struct device *dev,
+			      struct device_attribute *attr,
+			      const char *buf, size_t count)
+{
+	struct hid_device *hdev = container_of(dev, struct hid_device, dev);
+	struct ntrig_data *nd = hid_get_drvdata(hdev);
+
+	unsigned long val;
+
+	if (strict_strtoul(buf, 0, &val))
+		return -EINVAL;
+
+	if (val > nd->sensor_physical_height)
+		return -EINVAL;
+
+	nd->min_height = val * nd->sensor_logical_height /
+			       nd->sensor_physical_height;
+
+	return count;
+}
+
+static DEVICE_ATTR(min_height, S_IWUSR | S_IRUGO, show_min_height,
+		   set_min_height);
+
+static ssize_t show_activate_slack(struct device *dev,
+				   struct device_attribute *attr,
+				   char *buf)
+{
+	struct hid_device *hdev = container_of(dev, struct hid_device, dev);
+	struct ntrig_data *nd = hid_get_drvdata(hdev);
+
+	return sprintf(buf, "%d\n", nd->activate_slack);
+}
+
+static ssize_t set_activate_slack(struct device *dev,
+				  struct device_attribute *attr,
+				  const char *buf, size_t count)
+{
+	struct hid_device *hdev = container_of(dev, struct hid_device, dev);
+	struct ntrig_data *nd = hid_get_drvdata(hdev);
+
+	unsigned long val;
+
+	if (strict_strtoul(buf, 0, &val))
+		return -EINVAL;
+
+	if (val > 0x7f)
+		return -EINVAL;
+
+	nd->activate_slack = val;
+
+	return count;
+}
+
+static DEVICE_ATTR(activate_slack, S_IWUSR | S_IRUGO, show_activate_slack,
+		   set_activate_slack);
+
+static ssize_t show_activation_width(struct device *dev,
+				     struct device_attribute *attr,
+				     char *buf)
+{
+	struct hid_device *hdev = container_of(dev, struct hid_device, dev);
+	struct ntrig_data *nd = hid_get_drvdata(hdev);
+
+	return sprintf(buf, "%d\n", nd->activation_width *
+				    nd->sensor_physical_width /
+				    nd->sensor_logical_width);
+}
+
+static ssize_t set_activation_width(struct device *dev,
+				    struct device_attribute *attr,
+				    const char *buf, size_t count)
+{
+	struct hid_device *hdev = container_of(dev, struct hid_device, dev);
+	struct ntrig_data *nd = hid_get_drvdata(hdev);
+
+	unsigned long val;
+
+	if (strict_strtoul(buf, 0, &val))
+		return -EINVAL;
+
+	if (val > nd->sensor_physical_width)
+		return -EINVAL;
+
+	nd->activation_width = val * nd->sensor_logical_width /
+				     nd->sensor_physical_width;
+
+	return count;
+}
+
+static DEVICE_ATTR(activation_width, S_IWUSR | S_IRUGO, show_activation_width,
+		   set_activation_width);
+
+static ssize_t show_activation_height(struct device *dev,
+				      struct device_attribute *attr,
+				      char *buf)
+{
+	struct hid_device *hdev = container_of(dev, struct hid_device, dev);
+	struct ntrig_data *nd = hid_get_drvdata(hdev);
+
+	return sprintf(buf, "%d\n", nd->activation_height *
+				    nd->sensor_physical_height /
+				    nd->sensor_logical_height);
+}
+
+static ssize_t set_activation_height(struct device *dev,
+				     struct device_attribute *attr,
+				     const char *buf, size_t count)
+{
+	struct hid_device *hdev = container_of(dev, struct hid_device, dev);
+	struct ntrig_data *nd = hid_get_drvdata(hdev);
+
+	unsigned long val;
+
+	if (strict_strtoul(buf, 0, &val))
+		return -EINVAL;
+
+	if (val > nd->sensor_physical_height)
+		return -EINVAL;
+
+	nd->activation_height = val * nd->sensor_logical_height /
+				      nd->sensor_physical_height;
+
+	return count;
+}
+
+static DEVICE_ATTR(activation_height, S_IWUSR | S_IRUGO,
+		   show_activation_height, set_activation_height);
+
+static ssize_t show_deactivate_slack(struct device *dev,
+				     struct device_attribute *attr,
+				     char *buf)
+{
+	struct hid_device *hdev = container_of(dev, struct hid_device, dev);
+	struct ntrig_data *nd = hid_get_drvdata(hdev);
+
+	return sprintf(buf, "%d\n", -nd->deactivate_slack);
+}
+
+static ssize_t set_deactivate_slack(struct device *dev,
+				    struct device_attribute *attr,
+				    const char *buf, size_t count)
+{
+	struct hid_device *hdev = container_of(dev, struct hid_device, dev);
+	struct ntrig_data *nd = hid_get_drvdata(hdev);
+
+	unsigned long val;
+
+	if (strict_strtoul(buf, 0, &val))
+		return -EINVAL;
+
+	/*
+	 * No more than 8 terminal frames have been observed so far
+	 * and higher slack is highly likely to leave the single
+	 * touch emulation stuck down.
+	 */
+	if (val > 7)
+		return -EINVAL;
+
+	nd->deactivate_slack = -val;
+
+	return count;
+}
+
+static DEVICE_ATTR(deactivate_slack, S_IWUSR | S_IRUGO, show_deactivate_slack,
+		   set_deactivate_slack);
+
+static struct attribute *sysfs_attrs[] = {
+	&dev_attr_sensor_physical_width.attr,
+	&dev_attr_sensor_physical_height.attr,
+	&dev_attr_sensor_logical_width.attr,
+	&dev_attr_sensor_logical_height.attr,
+	&dev_attr_min_height.attr,
+	&dev_attr_min_width.attr,
+	&dev_attr_activate_slack.attr,
+	&dev_attr_activation_width.attr,
+	&dev_attr_activation_height.attr,
+	&dev_attr_deactivate_slack.attr,
+	NULL
+};
+
+static struct attribute_group ntrig_attribute_group = {
+	.attrs = sysfs_attrs
 };
 
 /*
@@ -49,6 +380,8 @@
 		struct hid_field *field, struct hid_usage *usage,
 		unsigned long **bit, int *max)
 {
+	struct ntrig_data *nd = hid_get_drvdata(hdev);
+
 	/* No special mappings needed for the pen and single touch */
 	if (field->physical)
 		return 0;
@@ -62,6 +395,21 @@
 			input_set_abs_params(hi->input, ABS_X,
 					field->logical_minimum,
 					field->logical_maximum, 0, 0);
+
+			if (!nd->sensor_logical_width) {
+				nd->sensor_logical_width =
+					field->logical_maximum -
+					field->logical_minimum;
+				nd->sensor_physical_width =
+					field->physical_maximum -
+					field->physical_minimum;
+				nd->activation_width = activation_width *
+					nd->sensor_logical_width /
+					nd->sensor_physical_width;
+				nd->min_width = min_width *
+					nd->sensor_logical_width /
+					nd->sensor_physical_width;
+			}
 			return 1;
 		case HID_GD_Y:
 			hid_map_usage(hi, usage, bit, max,
@@ -69,6 +417,21 @@
 			input_set_abs_params(hi->input, ABS_Y,
 					field->logical_minimum,
 					field->logical_maximum, 0, 0);
+
+			if (!nd->sensor_logical_height) {
+				nd->sensor_logical_height =
+					field->logical_maximum -
+					field->logical_minimum;
+				nd->sensor_physical_height =
+					field->physical_maximum -
+					field->physical_minimum;
+				nd->activation_height = activation_height *
+					nd->sensor_logical_height /
+					nd->sensor_physical_height;
+				nd->min_height = min_height *
+					nd->sensor_logical_height /
+					nd->sensor_physical_height;
+			}
 			return 1;
 		}
 		return 0;
@@ -201,20 +564,68 @@
 			if (nd->mt_foot_count != 4)
 				break;
 
-			/* Pen activity signal, trigger end of touch. */
+			/* Pen activity signal. */
 			if (nd->mt_footer[2]) {
+				/*
+				 * When the pen deactivates touch, we see a
+				 * bogus frame with ContactCount > 0.
+				 * We can
+				 * save a bit of work by ensuring act_state < 0
+				 * even if deactivation slack is turned off.
+				 */
+				nd->act_state = deactivate_slack - 1;
 				nd->confidence = 0;
 				break;
 			}
 
-			/* If the contact was invalid */
-			if (!(nd->confidence && nd->mt_footer[0])
-					|| nd->w <= 250
-					|| nd->h <= 190) {
-				nd->confidence = 0;
+			/*
+			 * The first footer value indicates the presence of a
+			 * finger.
+			 */
+			if (nd->mt_footer[0]) {
+				/*
+				 * We do not want to process contacts under
+				 * the size threshold, but do not want to
+				 * ignore them for activation state
+				 */
+				if (nd->w < nd->min_width ||
+				    nd->h < nd->min_height)
+					nd->confidence = 0;
+			} else
 				break;
+
+			if (nd->act_state > 0) {
+				/*
+				 * Contact meets the activation size threshold
+				 */
+				if (nd->w >= nd->activation_width &&
+				    nd->h >= nd->activation_height) {
+					if (nd->id)
+						/*
+						 * first contact, activate now
+						 */
+						nd->act_state = 0;
+					else {
+						/*
+						 * avoid corrupting this frame
+						 * but ensure next frame will
+						 * be active
+						 */
+						nd->act_state = 1;
+						break;
+					}
+				} else
+					/*
+					 * Defer adjusting the activation state
+					 * until the end of the frame.
+					 */
+					break;
 			}
 
+			/* Discarding this contact */
+			if (!nd->confidence)
+				break;
+
 			/* emit a normal (X, Y) for the first point only */
 			if (nd->id == 0) {
 				/*
@@ -227,8 +638,15 @@
 				input_event(input, EV_ABS, ABS_X, nd->x);
 				input_event(input, EV_ABS, ABS_Y, nd->y);
 			}
+
+			/* Emit MT events */
 			input_event(input, EV_ABS, ABS_MT_POSITION_X, nd->x);
 			input_event(input, EV_ABS, ABS_MT_POSITION_Y, nd->y);
+
+			/*
+			 * Translate from height and width to size
+			 * and orientation.
+			 */
 			if (nd->w > nd->h) {
 				input_event(input, EV_ABS,
 						ABS_MT_ORIENTATION, 1);
@@ -248,12 +666,88 @@
 			break;
 
 		case HID_DG_CONTACTCOUNT: /* End of a multitouch group */
-			if (!nd->reading_mt)
+			if (!nd->reading_mt) /* Just to be sure */
 				break;
 
 			nd->reading_mt = 0;
 
-			if (nd->first_contact_touch) {
+
+			/*
+			 * Activation state machine logic:
+			 *
+			 * Fundamental states:
+			 *	state >  0: Inactive
+			 *	state <= 0: Active
+			 *	state <  -deactivate_slack:
+			 *		 Pen termination of touch
+			 *
+			 * Specific values of interest
+			 *	state == activate_slack
+			 *		 no valid input since the last reset
+			 *
+			 *	state == 0
+			 *		 general operational state
+			 *
+			 *	state == -deactivate_slack
+			 *		 read sufficient empty frames to accept
+			 *		 the end of input and reset
+			 */
+
+			if (nd->act_state > 0) { /* Currently inactive */
+				if (value)
+					/*
+					 * Consider each live contact as
+					 * evidence of intentional activity.
+					 */
+					nd->act_state = (nd->act_state > value)
+							? nd->act_state - value
+							: 0;
+				else
+					/*
+					 * Empty frame before we hit the
+					 * activity threshold, reset.
+					 */
+					nd->act_state = nd->activate_slack;
+
+				/*
+				 * Entered this block inactive and no
+				 * coordinates sent this frame, so hold off
+				 * on button state.
+				 */
+				break;
+			} else { /* Currently active */
+				if (value && nd->act_state >=
+					     nd->deactivate_slack)
+					/*
+					 * Live point: clear accumulated
+					 * deactivation count.
+					 */
+					nd->act_state = 0;
+				else if (nd->act_state <= nd->deactivate_slack)
+					/*
+					 * We've consumed the deactivation
+					 * slack, time to deactivate and reset.
+					 */
+					nd->act_state =
+						nd->activate_slack;
+				else { /* Move towards deactivation */
+					nd->act_state--;
+					break;
+				}
+			}
+
+			if (nd->first_contact_touch && nd->act_state <= 0) {
+				/*
+				 * Check to see if we're ready to start
+				 * emitting touch events.
+				 *
+				 * Note: activation slack will decrease over
+				 * the course of the frame, and it will be
+				 * inconsistent from the start to the end of
+				 * the frame.  However if the frame starts
+				 * with slack, first_contact_touch will still
+				 * be 0 and we will not get to this point.
+				 */
 				input_report_key(input, BTN_TOOL_DOUBLETAP, 1);
 				input_report_key(input, BTN_TOUCH, 1);
 			} else {
@@ -263,7 +757,7 @@
 			break;
 
 		default:
-			/* fallback to the generic hidinput handling */
+			/* fall-back to the generic hidinput handling */
 			return 0;
 		}
 	}
@@ -293,6 +787,16 @@
 	}
 
 	nd->reading_mt = 0;
+	nd->min_width = 0;
+	nd->min_height = 0;
+	nd->activate_slack = activate_slack;
+	nd->act_state = activate_slack;
+	nd->deactivate_slack = -deactivate_slack;
+	nd->sensor_logical_width = 0;
+	nd->sensor_logical_height = 0;
+	nd->sensor_physical_width = 0;
+	nd->sensor_physical_height = 0;
+
 	hid_set_drvdata(hdev, nd);
 
 	ret = hid_parse(hdev);
@@ -344,6 +848,8 @@
 	if (report)
 		usbhid_submit_report(hdev, report, USB_DIR_OUT);
 
+	ret = sysfs_create_group(&hdev->dev.kobj,
+			&ntrig_attribute_group);
 
 	return 0;
 err_free:
@@ -353,6 +859,8 @@
 
 static void ntrig_remove(struct hid_device *hdev)
 {
+	sysfs_remove_group(&hdev->dev.kobj,
+			&ntrig_attribute_group);
 	hid_hw_stop(hdev);
 	kfree(hid_get_drvdata(hdev));
 }
diff --git a/drivers/hid/hid-picolcd.c b/drivers/hid/hid-picolcd.c
new file mode 100644
index 0000000..7aabf65
--- /dev/null
+++ b/drivers/hid/hid-picolcd.c
@@ -0,0 +1,2631 @@
+/***************************************************************************
+ *   Copyright (C) 2010 by Bruno Prémont <bonbons@linux-vserver.org>       *
+ *                                                                         *
+ *   Based on Logitech G13 driver (v0.4)                                   *
+ *     Copyright (C) 2009 by Rick L. Vinyard, Jr. <rvinyard@cs.nmsu.edu>   *
+ *                                                                         *
+ *   This program is free software: you can redistribute it and/or modify  *
+ *   it under the terms of the GNU General Public License as published by  *
+ *   the Free Software Foundation, version 2 of the License.               *
+ *                                                                         *
+ *   This driver is distributed in the hope that it will be useful, but    *
+ *   WITHOUT ANY WARRANTY; without even the implied warranty of            *
+ *   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU      *
+ *   General Public License for more details.                              *
+ *                                                                         *
+ *   You should have received a copy of the GNU General Public License     *
+ *   along with this software. If not see <http://www.gnu.org/licenses/>.  *
+ ***************************************************************************/
+
+#include <linux/hid.h>
+#include <linux/hid-debug.h>
+#include <linux/input.h>
+#include "hid-ids.h"
+#include "usbhid/usbhid.h"
+#include <linux/usb.h>
+
+#include <linux/fb.h>
+#include <linux/vmalloc.h>
+#include <linux/backlight.h>
+#include <linux/lcd.h>
+
+#include <linux/leds.h>
+
+#include <linux/seq_file.h>
+#include <linux/debugfs.h>
+
+#include <linux/completion.h>
+#include <linux/uaccess.h>
+
+#define PICOLCD_NAME "PicoLCD (graphic)"
+
+/* Report numbers */
+#define REPORT_ERROR_CODE      0x10 /* LCD: IN[16]  */
+#define   ERR_SUCCESS            0x00
+#define   ERR_PARAMETER_MISSING  0x01
+#define   ERR_DATA_MISSING       0x02
+#define   ERR_BLOCK_READ_ONLY    0x03
+#define   ERR_BLOCK_NOT_ERASABLE 0x04
+#define   ERR_BLOCK_TOO_BIG      0x05
+#define   ERR_SECTION_OVERFLOW   0x06
+#define   ERR_INVALID_CMD_LEN    0x07
+#define   ERR_INVALID_DATA_LEN   0x08
+#define REPORT_KEY_STATE       0x11 /* LCD: IN[2]   */
+#define REPORT_IR_DATA         0x21 /* LCD: IN[63]  */
+#define REPORT_EE_DATA         0x32 /* LCD: IN[63]  */
+#define REPORT_MEMORY          0x41 /* LCD: IN[63]  */
+#define REPORT_LED_STATE       0x81 /* LCD: OUT[1]  */
+#define REPORT_BRIGHTNESS      0x91 /* LCD: OUT[1]  */
+#define REPORT_CONTRAST        0x92 /* LCD: OUT[1]  */
+#define REPORT_RESET           0x93 /* LCD: OUT[2]  */
+#define REPORT_LCD_CMD         0x94 /* LCD: OUT[63] */
+#define REPORT_LCD_DATA        0x95 /* LCD: OUT[63] */
+#define REPORT_LCD_CMD_DATA    0x96 /* LCD: OUT[63] */
+#define	REPORT_EE_READ         0xa3 /* LCD: OUT[63] */
+#define REPORT_EE_WRITE        0xa4 /* LCD: OUT[63] */
+#define REPORT_ERASE_MEMORY    0xb2 /* LCD: OUT[2]  */
+#define REPORT_READ_MEMORY     0xb3 /* LCD: OUT[3]  */
+#define REPORT_WRITE_MEMORY    0xb4 /* LCD: OUT[63] */
+#define REPORT_SPLASH_RESTART  0xc1 /* LCD: OUT[1]  */
+#define REPORT_EXIT_KEYBOARD   0xef /* LCD: OUT[2]  */
+#define REPORT_VERSION         0xf1 /* LCD: IN[2],OUT[1]    Bootloader: IN[2],OUT[1]   */
+#define REPORT_BL_ERASE_MEMORY 0xf2 /*                      Bootloader: IN[36],OUT[4]  */
+#define REPORT_BL_READ_MEMORY  0xf3 /*                      Bootloader: IN[36],OUT[4]  */
+#define REPORT_BL_WRITE_MEMORY 0xf4 /*                      Bootloader: IN[36],OUT[36] */
+#define REPORT_DEVID           0xf5 /* LCD: IN[5], OUT[1]   Bootloader: IN[5],OUT[1]   */
+#define REPORT_SPLASH_SIZE     0xf6 /* LCD: IN[4], OUT[1]   */
+#define REPORT_HOOK_VERSION    0xf7 /* LCD: IN[2], OUT[1]   */
+#define REPORT_EXIT_FLASHER    0xff /*                      Bootloader: OUT[2]         */
+
+#ifdef CONFIG_HID_PICOLCD_FB
+/* Framebuffer
+ *
+ * The PicoLCD use a Topway LCD module of 256x64 pixel
+ * This display area is tiled over 4 controllers with 8 tiles
+ * each. Each tile has 8x64 pixel, each data byte representing
+ * a 1-bit wide vertical line of the tile.
+ *
+ * The display can be updated at a tile granularity.
+ *
+ *       Chip 1           Chip 2           Chip 3           Chip 4
+ * +----------------+----------------+----------------+----------------+
+ * |     Tile 1     |     Tile 1     |     Tile 1     |     Tile 1     |
+ * +----------------+----------------+----------------+----------------+
+ * |     Tile 2     |     Tile 2     |     Tile 2     |     Tile 2     |
+ * +----------------+----------------+----------------+----------------+
+ *                                  ...
+ * +----------------+----------------+----------------+----------------+
+ * |     Tile 8     |     Tile 8     |     Tile 8     |     Tile 8     |
+ * +----------------+----------------+----------------+----------------+
+ */
+#define PICOLCDFB_NAME "picolcdfb"
+#define PICOLCDFB_WIDTH (256)
+#define PICOLCDFB_HEIGHT (64)
+#define PICOLCDFB_SIZE (PICOLCDFB_WIDTH * PICOLCDFB_HEIGHT / 8)
+
+#define PICOLCDFB_UPDATE_RATE_LIMIT   10
+#define PICOLCDFB_UPDATE_RATE_DEFAULT  2
+
+/* Framebuffer visual structures */
+static const struct fb_fix_screeninfo picolcdfb_fix = {
+	.id          = PICOLCDFB_NAME,
+	.type        = FB_TYPE_PACKED_PIXELS,
+	.visual      = FB_VISUAL_MONO01,
+	.xpanstep    = 0,
+	.ypanstep    = 0,
+	.ywrapstep   = 0,
+	.line_length = PICOLCDFB_WIDTH / 8,
+	.accel       = FB_ACCEL_NONE,
+};
+
+static const struct fb_var_screeninfo picolcdfb_var = {
+	.xres           = PICOLCDFB_WIDTH,
+	.yres           = PICOLCDFB_HEIGHT,
+	.xres_virtual   = PICOLCDFB_WIDTH,
+	.yres_virtual   = PICOLCDFB_HEIGHT,
+	.width          = 103,
+	.height         = 26,
+	.bits_per_pixel = 1,
+	.grayscale      = 1,
+};
+#endif /* CONFIG_HID_PICOLCD_FB */
+
+/* Input device
+ *
+ * The PicoLCD has an IR receiver header, a built-in keypad with 5 keys
+ * and header for 4x4 key matrix. The built-in keys are part of the matrix.
+ */
+static const unsigned short def_keymap[] = {
+	KEY_RESERVED,	/* none */
+	KEY_BACK,	/* col 4 + row 1 */
+	KEY_HOMEPAGE,	/* col 3 + row 1 */
+	KEY_RESERVED,	/* col 2 + row 1 */
+	KEY_RESERVED,	/* col 1 + row 1 */
+	KEY_SCROLLUP,	/* col 4 + row 2 */
+	KEY_OK,		/* col 3 + row 2 */
+	KEY_SCROLLDOWN,	/* col 2 + row 2 */
+	KEY_RESERVED,	/* col 1 + row 2 */
+	KEY_RESERVED,	/* col 4 + row 3 */
+	KEY_RESERVED,	/* col 3 + row 3 */
+	KEY_RESERVED,	/* col 2 + row 3 */
+	KEY_RESERVED,	/* col 1 + row 3 */
+	KEY_RESERVED,	/* col 4 + row 4 */
+	KEY_RESERVED,	/* col 3 + row 4 */
+	KEY_RESERVED,	/* col 2 + row 4 */
+	KEY_RESERVED,	/* col 1 + row 4 */
+};
+#define PICOLCD_KEYS ARRAY_SIZE(def_keymap)
+
+/* Description of in-progress IO operation, used for operations
+ * that trigger response from device */
+struct picolcd_pending {
+	struct hid_report *out_report;
+	struct hid_report *in_report;
+	struct completion ready;
+	int raw_size;
+	u8 raw_data[64];
+};
+
+/* Per device data structure */
+struct picolcd_data {
+	struct hid_device *hdev;
+#ifdef CONFIG_DEBUG_FS
+	struct dentry *debug_reset;
+	struct dentry *debug_eeprom;
+	struct dentry *debug_flash;
+	struct mutex mutex_flash;
+	int addr_sz;
+#endif
+	u8 version[2];
+	unsigned short opmode_delay;
+	/* input stuff */
+	u8 pressed_keys[2];
+	struct input_dev *input_keys;
+	struct input_dev *input_cir;
+	unsigned short keycode[PICOLCD_KEYS];
+
+#ifdef CONFIG_HID_PICOLCD_FB
+	/* Framebuffer stuff */
+	u8 fb_update_rate;
+	u8 fb_bpp;
+	u8 *fb_vbitmap;		/* local copy of what was sent to PicoLCD */
+	u8 *fb_bitmap;		/* framebuffer */
+	struct fb_info *fb_info;
+	struct fb_deferred_io fb_defio;
+#endif /* CONFIG_HID_PICOLCD_FB */
+#ifdef CONFIG_HID_PICOLCD_LCD
+	struct lcd_device *lcd;
+	u8 lcd_contrast;
+#endif /* CONFIG_HID_PICOLCD_LCD */
+#ifdef CONFIG_HID_PICOLCD_BACKLIGHT
+	struct backlight_device *backlight;
+	u8 lcd_brightness;
+	u8 lcd_power;
+#endif /* CONFIG_HID_PICOLCD_BACKLIGHT */
+#ifdef CONFIG_HID_PICOLCD_LEDS
+	/* LED stuff */
+	u8 led_state;
+	struct led_classdev *led[8];
+#endif /* CONFIG_HID_PICOLCD_LEDS */
+
+	/* Housekeeping stuff */
+	spinlock_t lock;
+	struct mutex mutex;
+	struct picolcd_pending *pending;
+	int status;
+#define PICOLCD_BOOTLOADER 1
+#define PICOLCD_FAILED 2
+#define PICOLCD_READY_FB 4
+};
+
+
+/* Find a given report */
+#define picolcd_in_report(id, dev) picolcd_report(id, dev, HID_INPUT_REPORT)
+#define picolcd_out_report(id, dev) picolcd_report(id, dev, HID_OUTPUT_REPORT)
+
+static struct hid_report *picolcd_report(int id, struct hid_device *hdev, int dir)
+{
+	struct list_head *feature_report_list = &hdev->report_enum[dir].report_list;
+	struct hid_report *report = NULL;
+
+	list_for_each_entry(report, feature_report_list, list) {
+		if (report->id == id)
+			return report;
+	}
+	dev_warn(&hdev->dev, "No report with id 0x%x found\n", id);
+	return NULL;
+}
+
+#ifdef CONFIG_DEBUG_FS
+static void picolcd_debug_out_report(struct picolcd_data *data,
+		struct hid_device *hdev, struct hid_report *report);
+#define usbhid_submit_report(a, b, c) \
+	do { \
+		picolcd_debug_out_report(hid_get_drvdata(a), a, b); \
+		usbhid_submit_report(a, b, c); \
+	} while (0)
+#endif
+
+/* Submit a report and wait for a reply from device - if device fades away
+ * or does not respond in time, return NULL */
+static struct picolcd_pending *picolcd_send_and_wait(struct hid_device *hdev,
+		int report_id, const u8 *raw_data, int size)
+{
+	struct picolcd_data *data = hid_get_drvdata(hdev);
+	struct picolcd_pending *work;
+	struct hid_report *report = picolcd_out_report(report_id, hdev);
+	unsigned long flags;
+	int i, j, k;
+
+	if (!report || !data)
+		return NULL;
+	if (data->status & PICOLCD_FAILED)
+		return NULL;
+	work = kzalloc(sizeof(*work), GFP_KERNEL);
+	if (!work)
+		return NULL;
+
+	init_completion(&work->ready);
+	work->out_report = report;
+	work->in_report  = NULL;
+	work->raw_size   = 0;
+
+	mutex_lock(&data->mutex);
+	spin_lock_irqsave(&data->lock, flags);
+	for (i = k = 0; i < report->maxfield; i++)
+		for (j = 0; j < report->field[i]->report_count; j++) {
+			hid_set_field(report->field[i], j, k < size ? raw_data[k] : 0);
+			k++;
+		}
+	data->pending = work;
+	usbhid_submit_report(data->hdev, report, USB_DIR_OUT);
+	spin_unlock_irqrestore(&data->lock, flags);
+	wait_for_completion_interruptible_timeout(&work->ready, HZ*2);
+	spin_lock_irqsave(&data->lock, flags);
+	data->pending = NULL;
+	spin_unlock_irqrestore(&data->lock, flags);
+	mutex_unlock(&data->mutex);
+	return work;
+}
+
+#ifdef CONFIG_HID_PICOLCD_FB
+/* Send a given tile to PicoLCD */
+static int picolcd_fb_send_tile(struct hid_device *hdev, int chip, int tile)
+{
+	struct picolcd_data *data = hid_get_drvdata(hdev);
+	struct hid_report *report1 = picolcd_out_report(REPORT_LCD_CMD_DATA, hdev);
+	struct hid_report *report2 = picolcd_out_report(REPORT_LCD_DATA, hdev);
+	unsigned long flags;
+	u8 *tdata;
+	int i;
+
+	if (!report1 || report1->maxfield != 1 || !report2 || report2->maxfield != 1)
+		return -ENODEV;
+
+	spin_lock_irqsave(&data->lock, flags);
+	hid_set_field(report1->field[0],  0, chip << 2);
+	hid_set_field(report1->field[0],  1, 0x02);
+	hid_set_field(report1->field[0],  2, 0x00);
+	hid_set_field(report1->field[0],  3, 0x00);
+	hid_set_field(report1->field[0],  4, 0xb8 | tile);
+	hid_set_field(report1->field[0],  5, 0x00);
+	hid_set_field(report1->field[0],  6, 0x00);
+	hid_set_field(report1->field[0],  7, 0x40);
+	hid_set_field(report1->field[0],  8, 0x00);
+	hid_set_field(report1->field[0],  9, 0x00);
+	hid_set_field(report1->field[0], 10,   32);
+
+	hid_set_field(report2->field[0],  0, (chip << 2) | 0x01);
+	hid_set_field(report2->field[0],  1, 0x00);
+	hid_set_field(report2->field[0],  2, 0x00);
+	hid_set_field(report2->field[0],  3,   32);
+
+	tdata = data->fb_vbitmap + (tile * 4 + chip) * 64;
+	for (i = 0; i < 64; i++)
+		if (i < 32)
+			hid_set_field(report1->field[0], 11 + i, tdata[i]);
+		else
+			hid_set_field(report2->field[0], 4 + i - 32, tdata[i]);
+
+	usbhid_submit_report(data->hdev, report1, USB_DIR_OUT);
+	usbhid_submit_report(data->hdev, report2, USB_DIR_OUT);
+	spin_unlock_irqrestore(&data->lock, flags);
+	return 0;
+}
+
+/* Translate a single tile*/
+static int picolcd_fb_update_tile(u8 *vbitmap, const u8 *bitmap, int bpp,
+		int chip, int tile)
+{
+	int i, b, changed = 0;
+	u8 tdata[64];
+	u8 *vdata = vbitmap + (tile * 4 + chip) * 64;
+
+	if (bpp == 1) {
+		for (b = 7; b >= 0; b--) {
+			const u8 *bdata = bitmap + tile * 256 + chip * 8 + b * 32;
+			for (i = 0; i < 64; i++) {
+				tdata[i] <<= 1;
+				tdata[i] |= (bdata[i/8] >> (7 - i % 8)) & 0x01;
+			}
+		}
+	} else if (bpp == 8) {
+		for (b = 7; b >= 0; b--) {
+			const u8 *bdata = bitmap + (tile * 256 + chip * 8 + b * 32) * 8;
+			for (i = 0; i < 64; i++) {
+				tdata[i] <<= 1;
+				tdata[i] |= (bdata[i] & 0x80) ? 0x01 : 0x00;
+			}
+		}
+	} else {
+		/* Oops, we should never get here! */
+		WARN_ON(1);
+		return 0;
+	}
+
+	for (i = 0; i < 64; i++)
+		if (tdata[i] != vdata[i]) {
+			changed = 1;
+			vdata[i] = tdata[i];
+		}
+	return changed;
+}
+
+/* Reconfigure LCD display */
+static int picolcd_fb_reset(struct picolcd_data *data, int clear)
+{
+	struct hid_report *report = picolcd_out_report(REPORT_LCD_CMD, data->hdev);
+	int i, j;
+	unsigned long flags;
+	static const u8 mapcmd[8] = { 0x00, 0x02, 0x00, 0x64, 0x3f, 0x00, 0x64, 0xc0 };
+
+	if (!report || report->maxfield != 1)
+		return -ENODEV;
+
+	spin_lock_irqsave(&data->lock, flags);
+	for (i = 0; i < 4; i++) {
+		for (j = 0; j < report->field[0]->maxusage; j++)
+			if (j == 0)
+				hid_set_field(report->field[0], j, i << 2);
+			else if (j < sizeof(mapcmd))
+				hid_set_field(report->field[0], j, mapcmd[j]);
+			else
+				hid_set_field(report->field[0], j, 0);
+		usbhid_submit_report(data->hdev, report, USB_DIR_OUT);
+	}
+
+	data->status |= PICOLCD_READY_FB;
+	spin_unlock_irqrestore(&data->lock, flags);
+
+	if (data->fb_bitmap) {
+		if (clear) {
+			memset(data->fb_vbitmap, 0xff, PICOLCDFB_SIZE);
+			memset(data->fb_bitmap, 0, PICOLCDFB_SIZE*data->fb_bpp);
+		} else {
+			/* invert 1 byte in each tile to force resend */
+			for (i = 0; i < PICOLCDFB_SIZE; i += 64)
+				data->fb_vbitmap[i] = ~data->fb_vbitmap[i];
+		}
+	}
+
+	/* schedule first output of framebuffer */
+	if (data->fb_info)
+		schedule_delayed_work(&data->fb_info->deferred_work, 0);
+
+	return 0;
+}
+
+/* Update fb_vbitmap from the screen_base and send changed tiles to device */
+static void picolcd_fb_update(struct picolcd_data *data)
+{
+	int chip, tile, n;
+	unsigned long flags;
+
+	spin_lock_irqsave(&data->lock, flags);
+	if (!(data->status & PICOLCD_READY_FB)) {
+		spin_unlock_irqrestore(&data->lock, flags);
+		picolcd_fb_reset(data, 0);
+	} else {
+		spin_unlock_irqrestore(&data->lock, flags);
+	}
+
+	/*
+	 * Translate the framebuffer into the format needed by the PicoLCD.
+	 * See display layout above.
+	 * Do this one tile after the other and push those tiles that changed.
+	 *
+	 * Wait for our IO to complete as otherwise we might flood the queue!
+	 */
+	n = 0;
+	for (chip = 0; chip < 4; chip++)
+		for (tile = 0; tile < 8; tile++)
+			if (picolcd_fb_update_tile(data->fb_vbitmap,
+					data->fb_bitmap, data->fb_bpp, chip, tile)) {
+				n += 2;
+				if (n >= HID_OUTPUT_FIFO_SIZE / 2) {
+					usbhid_wait_io(data->hdev);
+					n = 0;
+				}
+				picolcd_fb_send_tile(data->hdev, chip, tile);
+			}
+	if (n)
+		usbhid_wait_io(data->hdev);
+}
+
+/* Stub to call the system default and update the image on the picoLCD */
+static void picolcd_fb_fillrect(struct fb_info *info,
+		const struct fb_fillrect *rect)
+{
+	if (!info->par)
+		return;
+	sys_fillrect(info, rect);
+
+	schedule_delayed_work(&info->deferred_work, 0);
+}
+
+/* Stub to call the system default and update the image on the picoLCD */
+static void picolcd_fb_copyarea(struct fb_info *info,
+		const struct fb_copyarea *area)
+{
+	if (!info->par)
+		return;
+	sys_copyarea(info, area);
+
+	schedule_delayed_work(&info->deferred_work, 0);
+}
+
+/* Stub to call the system default and update the image on the picoLCD */
+static void picolcd_fb_imageblit(struct fb_info *info, const struct fb_image *image)
+{
+	if (!info->par)
+		return;
+	sys_imageblit(info, image);
+
+	schedule_delayed_work(&info->deferred_work, 0);
+}
+
+/*
+ * this is the slow path from userspace. they can seek and write to
+ * the fb. it's inefficient to do anything less than a full screen draw
+ */
+static ssize_t picolcd_fb_write(struct fb_info *info, const char __user *buf,
+		size_t count, loff_t *ppos)
+{
+	ssize_t ret;
+	if (!info->par)
+		return -ENODEV;
+	ret = fb_sys_write(info, buf, count, ppos);
+	if (ret >= 0)
+		schedule_delayed_work(&info->deferred_work, 0);
+	return ret;
+}
+
+static int picolcd_fb_blank(int blank, struct fb_info *info)
+{
+	if (!info->par)
+		return -ENODEV;
+	/* We let fb notification do this for us via lcd/backlight device */
+	return 0;
+}
+
+static void picolcd_fb_destroy(struct fb_info *info)
+{
+	struct picolcd_data *data = info->par;
+	info->par = NULL;
+	if (data)
+		data->fb_info = NULL;
+	fb_deferred_io_cleanup(info);
+	framebuffer_release(info);
+}
+
+static int picolcd_fb_check_var(struct fb_var_screeninfo *var, struct fb_info *info)
+{
+	__u32 bpp      = var->bits_per_pixel;
+	__u32 activate = var->activate;
+
+	/* only allow 1/8 bit depth (8-bit is grayscale) */
+	*var = picolcdfb_var;
+	var->activate = activate;
+	if (bpp >= 8)
+		var->bits_per_pixel = 8;
+	else
+		var->bits_per_pixel = 1;
+	return 0;
+}
+
+static int picolcd_set_par(struct fb_info *info)
+{
+	struct picolcd_data *data = info->par;
+	u8 *o_fb, *n_fb;
+	if (info->var.bits_per_pixel == data->fb_bpp)
+		return 0;
+	/* switch between 1/8 bit depths */
+	if (info->var.bits_per_pixel != 1 && info->var.bits_per_pixel != 8)
+		return -EINVAL;
+
+	o_fb = data->fb_bitmap;
+	n_fb = vmalloc(PICOLCDFB_SIZE*info->var.bits_per_pixel);
+	if (!n_fb)
+		return -ENOMEM;
+
+	fb_deferred_io_cleanup(info);
+	/* translate FB content to new bits-per-pixel */
+	if (info->var.bits_per_pixel == 1) {
+		int i, b;
+		for (i = 0; i < PICOLCDFB_SIZE; i++) {
+			u8 p = 0;
+			for (b = 0; b < 8; b++) {
+				p <<= 1;
+				p |= o_fb[i*8+b] ? 0x01 : 0x00;
+			}
+		}
+		info->fix.visual = FB_VISUAL_MONO01;
+		info->fix.line_length = PICOLCDFB_WIDTH / 8;
+	} else {
+		int i;
+		for (i = 0; i < PICOLCDFB_SIZE * 8; i++)
+			n_fb[i] = o_fb[i/8] & (0x01 << (7 - i % 8)) ? 0xff : 0x00;
+		info->fix.visual = FB_VISUAL_TRUECOLOR;
+		info->fix.line_length = PICOLCDFB_WIDTH;
+	}
+
+	data->fb_bitmap   = n_fb;
+	data->fb_bpp      = info->var.bits_per_pixel;
+	info->screen_base = (char __force __iomem *)n_fb;
+	info->fix.smem_start = (unsigned long)n_fb;
+	info->fix.smem_len   = PICOLCDFB_SIZE*data->fb_bpp;
+	fb_deferred_io_init(info);
+	vfree(o_fb);
+	return 0;
+}
+
+/* Note this can't be const because of struct fb_info definition */
+static struct fb_ops picolcdfb_ops = {
+	.owner        = THIS_MODULE,
+	.fb_destroy   = picolcd_fb_destroy,
+	.fb_read      = fb_sys_read,
+	.fb_write     = picolcd_fb_write,
+	.fb_blank     = picolcd_fb_blank,
+	.fb_fillrect  = picolcd_fb_fillrect,
+	.fb_copyarea  = picolcd_fb_copyarea,
+	.fb_imageblit = picolcd_fb_imageblit,
+	.fb_check_var = picolcd_fb_check_var,
+	.fb_set_par   = picolcd_set_par,
+};
+
+
+/* Callback from deferred IO workqueue */
+static void picolcd_fb_deferred_io(struct fb_info *info, struct list_head *pagelist)
+{
+	picolcd_fb_update(info->par);
+}
+
+static const struct fb_deferred_io picolcd_fb_defio = {
+	.delay = HZ / PICOLCDFB_UPDATE_RATE_DEFAULT,
+	.deferred_io = picolcd_fb_deferred_io,
+};
+
+
+/*
+ * The "fb_update_rate" sysfs attribute
+ */
+static ssize_t picolcd_fb_update_rate_show(struct device *dev,
+		struct device_attribute *attr, char *buf)
+{
+	struct picolcd_data *data = dev_get_drvdata(dev);
+	unsigned i, fb_update_rate = data->fb_update_rate;
+	size_t ret = 0;
+
+	for (i = 1; i <= PICOLCDFB_UPDATE_RATE_LIMIT; i++)
+		if (ret >= PAGE_SIZE)
+			break;
+		else if (i == fb_update_rate)
+			ret += snprintf(buf+ret, PAGE_SIZE-ret, "[%u] ", i);
+		else
+			ret += snprintf(buf+ret, PAGE_SIZE-ret, "%u ", i);
+	if (ret > 0)
+		buf[min(ret, (size_t)PAGE_SIZE)-1] = '\n';
+	return ret;
+}
+
+static ssize_t picolcd_fb_update_rate_store(struct device *dev,
+		struct device_attribute *attr, const char *buf, size_t count)
+{
+	struct picolcd_data *data = dev_get_drvdata(dev);
+	int i;
+	unsigned u;
+
+	if (count < 1 || count > 10)
+		return -EINVAL;
+
+	i = sscanf(buf, "%u", &u);
+	if (i != 1)
+		return -EINVAL;
+
+	if (u > PICOLCDFB_UPDATE_RATE_LIMIT)
+		return -ERANGE;
+	else if (u == 0)
+		u = PICOLCDFB_UPDATE_RATE_DEFAULT;
+
+	data->fb_update_rate = u;
+	data->fb_defio.delay = HZ / data->fb_update_rate;
+	return count;
+}
+
+static DEVICE_ATTR(fb_update_rate, 0666, picolcd_fb_update_rate_show,
+		picolcd_fb_update_rate_store);
+
+/* initialize Framebuffer device */
+static int picolcd_init_framebuffer(struct picolcd_data *data)
+{
+	struct device *dev = &data->hdev->dev;
+	struct fb_info *info = NULL;
+	int error = -ENOMEM;
+	u8 *fb_vbitmap = NULL;
+	u8 *fb_bitmap  = NULL;
+
+	fb_bitmap = vmalloc(PICOLCDFB_SIZE*picolcdfb_var.bits_per_pixel);
+	if (fb_bitmap == NULL) {
+		dev_err(dev, "can't get a free page for framebuffer\n");
+		goto err_nomem;
+	}
+
+	fb_vbitmap = kmalloc(PICOLCDFB_SIZE, GFP_KERNEL);
+	if (fb_vbitmap == NULL) {
+		dev_err(dev, "can't alloc vbitmap image buffer\n");
+		goto err_nomem;
+	}
+
+	data->fb_update_rate = PICOLCDFB_UPDATE_RATE_DEFAULT;
+	data->fb_defio = picolcd_fb_defio;
+	info = framebuffer_alloc(0, dev);
+	if (info == NULL) {
+		dev_err(dev, "failed to allocate a framebuffer\n");
+		goto err_nomem;
+	}
+
+	info->fbdefio = &data->fb_defio;
+	info->screen_base = (char __force __iomem *)fb_bitmap;
+	info->fbops = &picolcdfb_ops;
+	info->var = picolcdfb_var;
+	info->fix = picolcdfb_fix;
+	info->fix.smem_len   = PICOLCDFB_SIZE;
+	info->fix.smem_start = (unsigned long)fb_bitmap;
+	info->par = data;
+	info->flags = FBINFO_FLAG_DEFAULT;
+
+	data->fb_vbitmap = fb_vbitmap;
+	data->fb_bitmap  = fb_bitmap;
+	data->fb_bpp     = picolcdfb_var.bits_per_pixel;
+	error = picolcd_fb_reset(data, 1);
+	if (error) {
+		dev_err(dev, "failed to configure display\n");
+		goto err_cleanup;
+	}
+	error = device_create_file(dev, &dev_attr_fb_update_rate);
+	if (error) {
+		dev_err(dev, "failed to create sysfs attributes\n");
+		goto err_cleanup;
+	}
+	data->fb_info    = info;
+	error = register_framebuffer(info);
+	if (error) {
+		dev_err(dev, "failed to register framebuffer\n");
+		goto err_sysfs;
+	}
+	fb_deferred_io_init(info);
+	/* schedule first output of framebuffer */
+	schedule_delayed_work(&info->deferred_work, 0);
+	return 0;
+
+err_sysfs:
+	device_remove_file(dev, &dev_attr_fb_update_rate);
+err_cleanup:
+	data->fb_vbitmap = NULL;
+	data->fb_bitmap  = NULL;
+	data->fb_bpp     = 0;
+	data->fb_info    = NULL;
+
+err_nomem:
+	framebuffer_release(info);
+	vfree(fb_bitmap);
+	kfree(fb_vbitmap);
+	return error;
+}
+
+static void picolcd_exit_framebuffer(struct picolcd_data *data)
+{
+	struct fb_info *info = data->fb_info;
+	u8 *fb_vbitmap = data->fb_vbitmap;
+	u8 *fb_bitmap  = data->fb_bitmap;
+
+	if (!info)
+		return;
+
+	data->fb_vbitmap = NULL;
+	data->fb_bitmap  = NULL;
+	data->fb_bpp     = 0;
+	data->fb_info    = NULL;
+	device_remove_file(&data->hdev->dev, &dev_attr_fb_update_rate);
+	fb_deferred_io_cleanup(info);
+	unregister_framebuffer(info);
+	vfree(fb_bitmap);
+	kfree(fb_vbitmap);
+}
+
+#define picolcd_fbinfo(d) ((d)->fb_info)
+#else
+static inline int picolcd_fb_reset(struct picolcd_data *data, int clear)
+{
+	return 0;
+}
+static inline int picolcd_init_framebuffer(struct picolcd_data *data)
+{
+	return 0;
+}
+static inline void picolcd_exit_framebuffer(struct picolcd_data *data)
+{
+}
+#define picolcd_fbinfo(d) NULL
+#endif /* CONFIG_HID_PICOLCD_FB */
+
+#ifdef CONFIG_HID_PICOLCD_BACKLIGHT
+/*
+ * backlight class device
+ */
+static int picolcd_get_brightness(struct backlight_device *bdev)
+{
+	struct picolcd_data *data = bl_get_data(bdev);
+	return data->lcd_brightness;
+}
+
+static int picolcd_set_brightness(struct backlight_device *bdev)
+{
+	struct picolcd_data *data = bl_get_data(bdev);
+	struct hid_report *report = picolcd_out_report(REPORT_BRIGHTNESS, data->hdev);
+	unsigned long flags;
+
+	if (!report || report->maxfield != 1 || report->field[0]->report_count != 1)
+		return -ENODEV;
+
+	data->lcd_brightness = bdev->props.brightness & 0x0ff;
+	data->lcd_power      = bdev->props.power;
+	spin_lock_irqsave(&data->lock, flags);
+	hid_set_field(report->field[0], 0, data->lcd_power == FB_BLANK_UNBLANK ? data->lcd_brightness : 0);
+	usbhid_submit_report(data->hdev, report, USB_DIR_OUT);
+	spin_unlock_irqrestore(&data->lock, flags);
+	return 0;
+}
+
+static int picolcd_check_bl_fb(struct backlight_device *bdev, struct fb_info *fb)
+{
+	return fb && fb == picolcd_fbinfo((struct picolcd_data *)bl_get_data(bdev));
+}
+
+static const struct backlight_ops picolcd_blops = {
+	.update_status  = picolcd_set_brightness,
+	.get_brightness = picolcd_get_brightness,
+	.check_fb       = picolcd_check_bl_fb,
+};
+
+static int picolcd_init_backlight(struct picolcd_data *data, struct hid_report *report)
+{
+	struct device *dev = &data->hdev->dev;
+	struct backlight_device *bdev;
+	struct backlight_properties props;
+	if (!report)
+		return -ENODEV;
+	if (report->maxfield != 1 || report->field[0]->report_count != 1 ||
+			report->field[0]->report_size != 8) {
+		dev_err(dev, "unsupported BRIGHTNESS report");
+		return -EINVAL;
+	}
+
+	memset(&props, 0, sizeof(props));
+	props.max_brightness = 0xff;
+	bdev = backlight_device_register(dev_name(dev), dev, data,
+			&picolcd_blops, &props);
+	if (IS_ERR(bdev)) {
+		dev_err(dev, "failed to register backlight\n");
+		return PTR_ERR(bdev);
+	}
+	bdev->props.brightness     = 0xff;
+	data->lcd_brightness       = 0xff;
+	data->backlight            = bdev;
+	picolcd_set_brightness(bdev);
+	return 0;
+}
+
+static void picolcd_exit_backlight(struct picolcd_data *data)
+{
+	struct backlight_device *bdev = data->backlight;
+
+	data->backlight = NULL;
+	if (bdev)
+		backlight_device_unregister(bdev);
+}
+
+static inline int picolcd_resume_backlight(struct picolcd_data *data)
+{
+	if (!data->backlight)
+		return 0;
+	return picolcd_set_brightness(data->backlight);
+}
+
+#ifdef CONFIG_PM
+static void picolcd_suspend_backlight(struct picolcd_data *data)
+{
+	int bl_power = data->lcd_power;
+	if (!data->backlight)
+		return;
+
+	data->backlight->props.power = FB_BLANK_POWERDOWN;
+	picolcd_set_brightness(data->backlight);
+	data->lcd_power = data->backlight->props.power = bl_power;
+}
+#endif /* CONFIG_PM */
+#else
+static inline int picolcd_init_backlight(struct picolcd_data *data,
+		struct hid_report *report)
+{
+	return 0;
+}
+static inline void picolcd_exit_backlight(struct picolcd_data *data)
+{
+}
+static inline int picolcd_resume_backlight(struct picolcd_data *data)
+{
+	return 0;
+}
+static inline void picolcd_suspend_backlight(struct picolcd_data *data)
+{
+}
+#endif /* CONFIG_HID_PICOLCD_BACKLIGHT */
+
+#ifdef CONFIG_HID_PICOLCD_LCD
+/*
+ * lcd class device
+ */
+static int picolcd_get_contrast(struct lcd_device *ldev)
+{
+	struct picolcd_data *data = lcd_get_data(ldev);
+	return data->lcd_contrast;
+}
+
+static int picolcd_set_contrast(struct lcd_device *ldev, int contrast)
+{
+	struct picolcd_data *data = lcd_get_data(ldev);
+	struct hid_report *report = picolcd_out_report(REPORT_CONTRAST, data->hdev);
+	unsigned long flags;
+
+	if (!report || report->maxfield != 1 || report->field[0]->report_count != 1)
+		return -ENODEV;
+
+	data->lcd_contrast = contrast & 0x0ff;
+	spin_lock_irqsave(&data->lock, flags);
+	hid_set_field(report->field[0], 0, data->lcd_contrast);
+	usbhid_submit_report(data->hdev, report, USB_DIR_OUT);
+	spin_unlock_irqrestore(&data->lock, flags);
+	return 0;
+}
+
+static int picolcd_check_lcd_fb(struct lcd_device *ldev, struct fb_info *fb)
+{
+	return fb && fb == picolcd_fbinfo((struct picolcd_data *)lcd_get_data(ldev));
+}
+
+static struct lcd_ops picolcd_lcdops = {
+	.get_contrast   = picolcd_get_contrast,
+	.set_contrast   = picolcd_set_contrast,
+	.check_fb       = picolcd_check_lcd_fb,
+};
+
+static int picolcd_init_lcd(struct picolcd_data *data, struct hid_report *report)
+{
+	struct device *dev = &data->hdev->dev;
+	struct lcd_device *ldev;
+
+	if (!report)
+		return -ENODEV;
+	if (report->maxfield != 1 || report->field[0]->report_count != 1 ||
+			report->field[0]->report_size != 8) {
+		dev_err(dev, "unsupported CONTRAST report");
+		return -EINVAL;
+	}
+
+	ldev = lcd_device_register(dev_name(dev), dev, data, &picolcd_lcdops);
+	if (IS_ERR(ldev)) {
+		dev_err(dev, "failed to register LCD\n");
+		return PTR_ERR(ldev);
+	}
+	ldev->props.max_contrast = 0x0ff;
+	data->lcd_contrast = 0xe5;
+	data->lcd = ldev;
+	picolcd_set_contrast(ldev, 0xe5);
+	return 0;
+}
+
+static void picolcd_exit_lcd(struct picolcd_data *data)
+{
+	struct lcd_device *ldev = data->lcd;
+
+	data->lcd = NULL;
+	if (ldev)
+		lcd_device_unregister(ldev);
+}
+
+static inline int picolcd_resume_lcd(struct picolcd_data *data)
+{
+	if (!data->lcd)
+		return 0;
+	return picolcd_set_contrast(data->lcd, data->lcd_contrast);
+}
+#else
+static inline int picolcd_init_lcd(struct picolcd_data *data,
+		struct hid_report *report)
+{
+	return 0;
+}
+static inline void picolcd_exit_lcd(struct picolcd_data *data)
+{
+}
+static inline int picolcd_resume_lcd(struct picolcd_data *data)
+{
+	return 0;
+}
+#endif /* CONFIG_HID_PICOLCD_LCD */
+
+#ifdef CONFIG_HID_PICOLCD_LEDS
+/**
+ * LED class device
+ */
+static void picolcd_leds_set(struct picolcd_data *data)
+{
+	struct hid_report *report;
+	unsigned long flags;
+
+	if (!data->led[0])
+		return;
+	report = picolcd_out_report(REPORT_LED_STATE, data->hdev);
+	if (!report || report->maxfield != 1 || report->field[0]->report_count != 1)
+		return;
+
+	spin_lock_irqsave(&data->lock, flags);
+	hid_set_field(report->field[0], 0, data->led_state);
+	usbhid_submit_report(data->hdev, report, USB_DIR_OUT);
+	spin_unlock_irqrestore(&data->lock, flags);
+}
+
+static void picolcd_led_set_brightness(struct led_classdev *led_cdev,
+			enum led_brightness value)
+{
+	struct device *dev;
+	struct hid_device *hdev;
+	struct picolcd_data *data;
+	int i, state = 0;
+
+	dev  = led_cdev->dev->parent;
+	hdev = container_of(dev, struct hid_device, dev);
+	data = hid_get_drvdata(hdev);
+	for (i = 0; i < 8; i++) {
+		if (led_cdev != data->led[i])
+			continue;
+		state = (data->led_state >> i) & 1;
+		if (value == LED_OFF && state) {
+			data->led_state &= ~(1 << i);
+			picolcd_leds_set(data);
+		} else if (value != LED_OFF && !state) {
+			data->led_state |= 1 << i;
+			picolcd_leds_set(data);
+		}
+		break;
+	}
+}
+
+static enum led_brightness picolcd_led_get_brightness(struct led_classdev *led_cdev)
+{
+	struct device *dev;
+	struct hid_device *hdev;
+	struct picolcd_data *data;
+	int i, value = 0;
+
+	dev  = led_cdev->dev->parent;
+	hdev = container_of(dev, struct hid_device, dev);
+	data = hid_get_drvdata(hdev);
+	for (i = 0; i < 8; i++)
+		if (led_cdev == data->led[i]) {
+			value = (data->led_state >> i) & 1;
+			break;
+		}
+	return value ? LED_FULL : LED_OFF;
+}
+
+static int picolcd_init_leds(struct picolcd_data *data, struct hid_report *report)
+{
+	struct device *dev = &data->hdev->dev;
+	struct led_classdev *led;
+	size_t name_sz = strlen(dev_name(dev)) + 8;
+	char *name;
+	int i, ret = 0;
+
+	if (!report)
+		return -ENODEV;
+	if (report->maxfield != 1 || report->field[0]->report_count != 1 ||
+			report->field[0]->report_size != 8) {
+		dev_err(dev, "unsupported LED_STATE report");
+		return -EINVAL;
+	}
+
+	for (i = 0; i < 8; i++) {
+		led = kzalloc(sizeof(struct led_classdev)+name_sz, GFP_KERNEL);
+		if (!led) {
+			dev_err(dev, "can't allocate memory for LED %d\n", i);
+			ret = -ENOMEM;
+			goto err;
+		}
+		name = (void *)(&led[1]);
+		snprintf(name, name_sz, "%s::GPO%d", dev_name(dev), i);
+		led->name = name;
+		led->brightness = 0;
+		led->max_brightness = 1;
+		led->brightness_get = picolcd_led_get_brightness;
+		led->brightness_set = picolcd_led_set_brightness;
+
+		data->led[i] = led;
+		ret = led_classdev_register(dev, data->led[i]);
+		if (ret) {
+			data->led[i] = NULL;
+			kfree(led);
+			dev_err(dev, "can't register LED %d\n", i);
+			goto err;
+		}
+	}
+	return 0;
+err:
+	for (i = 0; i < 8; i++)
+		if (data->led[i]) {
+			led = data->led[i];
+			data->led[i] = NULL;
+			led_classdev_unregister(led);
+			kfree(led);
+		}
+	return ret;
+}
+
+static void picolcd_exit_leds(struct picolcd_data *data)
+{
+	struct led_classdev *led;
+	int i;
+
+	for (i = 0; i < 8; i++) {
+		led = data->led[i];
+		data->led[i] = NULL;
+		if (!led)
+			continue;
+		led_classdev_unregister(led);
+		kfree(led);
+	}
+}
+
+#else
+static inline int picolcd_init_leds(struct picolcd_data *data,
+		struct hid_report *report)
+{
+	return 0;
+}
+static inline void picolcd_exit_leds(struct picolcd_data *data)
+{
+}
+static inline int picolcd_leds_set(struct picolcd_data *data)
+{
+	return 0;
+}
+#endif /* CONFIG_HID_PICOLCD_LEDS */
+
+/*
+ * input class device
+ */
+static int picolcd_raw_keypad(struct picolcd_data *data,
+		struct hid_report *report, u8 *raw_data, int size)
+{
+	/*
+	 * Keypad event
+	 * First and second data bytes list currently pressed keys,
+	 * 0x00 means no key and at most 2 keys may be pressed at same time
+	 */
+	int i, j;
+
+	/* determine newly pressed keys */
+	for (i = 0; i < size; i++) {
+		unsigned int key_code;
+		if (raw_data[i] == 0)
+			continue;
+		for (j = 0; j < sizeof(data->pressed_keys); j++)
+			if (data->pressed_keys[j] == raw_data[i])
+				goto key_already_down;
+		for (j = 0; j < sizeof(data->pressed_keys); j++)
+			if (data->pressed_keys[j] == 0) {
+				data->pressed_keys[j] = raw_data[i];
+				break;
+			}
+		input_event(data->input_keys, EV_MSC, MSC_SCAN, raw_data[i]);
+		if (raw_data[i] < PICOLCD_KEYS)
+			key_code = data->keycode[raw_data[i]];
+		else
+			key_code = KEY_UNKNOWN;
+		if (key_code != KEY_UNKNOWN) {
+			dbg_hid(PICOLCD_NAME " got key press for %u:%d",
+					raw_data[i], key_code);
+			input_report_key(data->input_keys, key_code, 1);
+		}
+		input_sync(data->input_keys);
+key_already_down:
+		continue;
+	}
+
+	/* determine newly released keys */
+	for (j = 0; j < sizeof(data->pressed_keys); j++) {
+		unsigned int key_code;
+		if (data->pressed_keys[j] == 0)
+			continue;
+		for (i = 0; i < size; i++)
+			if (data->pressed_keys[j] == raw_data[i])
+				goto key_still_down;
+		input_event(data->input_keys, EV_MSC, MSC_SCAN, data->pressed_keys[j]);
+		if (data->pressed_keys[j] < PICOLCD_KEYS)
+			key_code = data->keycode[data->pressed_keys[j]];
+		else
+			key_code = KEY_UNKNOWN;
+		if (key_code != KEY_UNKNOWN) {
+			dbg_hid(PICOLCD_NAME " got key release for %u:%d",
+					data->pressed_keys[j], key_code);
+			input_report_key(data->input_keys, key_code, 0);
+		}
+		input_sync(data->input_keys);
+		data->pressed_keys[j] = 0;
+key_still_down:
+		continue;
+	}
+	return 1;
+}
+
+static int picolcd_raw_cir(struct picolcd_data *data,
+		struct hid_report *report, u8 *raw_data, int size)
+{
+	/* Need understanding of CIR data format to implement ... */
+	return 1;
+}
+
+static int picolcd_check_version(struct hid_device *hdev)
+{
+	struct picolcd_data *data = hid_get_drvdata(hdev);
+	struct picolcd_pending *verinfo;
+	int ret = 0;
+
+	if (!data)
+		return -ENODEV;
+
+	verinfo = picolcd_send_and_wait(hdev, REPORT_VERSION, NULL, 0);
+	if (!verinfo) {
+		dev_err(&hdev->dev, "no version response from PicoLCD");
+		return -ENODEV;
+	}
+
+	if (verinfo->raw_size == 2) {
+		data->version[0] = verinfo->raw_data[1];
+		data->version[1] = verinfo->raw_data[0];
+		if (data->status & PICOLCD_BOOTLOADER) {
+			dev_info(&hdev->dev, "PicoLCD, bootloader version %d.%d\n",
+					verinfo->raw_data[1], verinfo->raw_data[0]);
+		} else {
+			dev_info(&hdev->dev, "PicoLCD, firmware version %d.%d\n",
+					verinfo->raw_data[1], verinfo->raw_data[0]);
+		}
+	} else {
+		dev_err(&hdev->dev, "confused, got unexpected version response from PicoLCD\n");
+		ret = -EINVAL;
+	}
+	kfree(verinfo);
+	return ret;
+}
+
+/*
+ * Reset our device and wait for answer to VERSION request
+ */
+static int picolcd_reset(struct hid_device *hdev)
+{
+	struct picolcd_data *data = hid_get_drvdata(hdev);
+	struct hid_report *report = picolcd_out_report(REPORT_RESET, hdev);
+	unsigned long flags;
+	int error;
+
+	if (!data || !report || report->maxfield != 1)
+		return -ENODEV;
+
+	spin_lock_irqsave(&data->lock, flags);
+	if (hdev->product == USB_DEVICE_ID_PICOLCD_BOOTLOADER)
+		data->status |= PICOLCD_BOOTLOADER;
+
+	/* perform the reset */
+	hid_set_field(report->field[0], 0, 1);
+	usbhid_submit_report(hdev, report, USB_DIR_OUT);
+	spin_unlock_irqrestore(&data->lock, flags);
+
+	error = picolcd_check_version(hdev);
+	if (error)
+		return error;
+
+	picolcd_resume_lcd(data);
+	picolcd_resume_backlight(data);
+#ifdef CONFIG_HID_PICOLCD_FB
+	if (data->fb_info)
+		schedule_delayed_work(&data->fb_info->deferred_work, 0);
+#endif /* CONFIG_HID_PICOLCD_FB */
+
+	picolcd_leds_set(data);
+	return 0;
+}
+
+/*
+ * The "operation_mode" sysfs attribute
+ */
+static ssize_t picolcd_operation_mode_show(struct device *dev,
+		struct device_attribute *attr, char *buf)
+{
+	struct picolcd_data *data = dev_get_drvdata(dev);
+
+	if (data->status & PICOLCD_BOOTLOADER)
+		return snprintf(buf, PAGE_SIZE, "[bootloader] lcd\n");
+	else
+		return snprintf(buf, PAGE_SIZE, "bootloader [lcd]\n");
+}
+
+static ssize_t picolcd_operation_mode_store(struct device *dev,
+		struct device_attribute *attr, const char *buf, size_t count)
+{
+	struct picolcd_data *data = dev_get_drvdata(dev);
+	struct hid_report *report = NULL;
+	size_t cnt = count;
+	int timeout = data->opmode_delay;
+	unsigned long flags;
+
+	if (cnt >= 3 && strncmp("lcd", buf, 3) == 0) {
+		if (data->status & PICOLCD_BOOTLOADER)
+			report = picolcd_out_report(REPORT_EXIT_FLASHER, data->hdev);
+		buf += 3;
+		cnt -= 3;
+	} else if (cnt >= 10 && strncmp("bootloader", buf, 10) == 0) {
+		if (!(data->status & PICOLCD_BOOTLOADER))
+			report = picolcd_out_report(REPORT_EXIT_KEYBOARD, data->hdev);
+		buf += 10;
+		cnt -= 10;
+	}
+	if (!report)
+		return -EINVAL;
+
+	while (cnt > 0 && (buf[cnt-1] == '\n' || buf[cnt-1] == '\r'))
+		cnt--;
+	if (cnt != 0)
+		return -EINVAL;
+
+	spin_lock_irqsave(&data->lock, flags);
+	hid_set_field(report->field[0], 0, timeout & 0xff);
+	hid_set_field(report->field[0], 1, (timeout >> 8) & 0xff);
+	usbhid_submit_report(data->hdev, report, USB_DIR_OUT);
+	spin_unlock_irqrestore(&data->lock, flags);
+	return count;
+}
+
+static DEVICE_ATTR(operation_mode, 0644, picolcd_operation_mode_show,
+		picolcd_operation_mode_store);
+
+/*
+ * The "operation_mode_delay" sysfs attribute
+ */
+static ssize_t picolcd_operation_mode_delay_show(struct device *dev,
+		struct device_attribute *attr, char *buf)
+{
+	struct picolcd_data *data = dev_get_drvdata(dev);
+
+	return snprintf(buf, PAGE_SIZE, "%hu\n", data->opmode_delay);
+}
+
+static ssize_t picolcd_operation_mode_delay_store(struct device *dev,
+		struct device_attribute *attr, const char *buf, size_t count)
+{
+	struct picolcd_data *data = dev_get_drvdata(dev);
+	unsigned u;
+	if (sscanf(buf, "%u", &u) != 1)
+		return -EINVAL;
+	if (u > 30000)
+		return -EINVAL;
+	else
+		data->opmode_delay = u;
+	return count;
+}
+
+static DEVICE_ATTR(operation_mode_delay, 0644, picolcd_operation_mode_delay_show,
+		picolcd_operation_mode_delay_store);
+
+
+#ifdef CONFIG_DEBUG_FS
+/*
+ * The "reset" file
+ */
+static int picolcd_debug_reset_show(struct seq_file *f, void *p)
+{
+	if (picolcd_fbinfo((struct picolcd_data *)f->private))
+		seq_printf(f, "all fb\n");
+	else
+		seq_printf(f, "all\n");
+	return 0;
+}
+
+static int picolcd_debug_reset_open(struct inode *inode, struct file *f)
+{
+	return single_open(f, picolcd_debug_reset_show, inode->i_private);
+}
+
+static ssize_t picolcd_debug_reset_write(struct file *f, const char __user *user_buf,
+		size_t count, loff_t *ppos)
+{
+	struct picolcd_data *data = ((struct seq_file *)f->private_data)->private;
+	char buf[32];
+	size_t cnt = min(count, sizeof(buf)-1);
+	if (copy_from_user(buf, user_buf, cnt))
+		return -EFAULT;
+
+	while (cnt > 0 && (buf[cnt-1] == ' ' || buf[cnt-1] == '\n'))
+		cnt--;
+	buf[cnt] = '\0';
+	if (strcmp(buf, "all") == 0) {
+		picolcd_reset(data->hdev);
+		picolcd_fb_reset(data, 1);
+	} else if (strcmp(buf, "fb") == 0) {
+		picolcd_fb_reset(data, 1);
+	} else {
+		return -EINVAL;
+	}
+	return count;
+}
+
+static const struct file_operations picolcd_debug_reset_fops = {
+	.owner    = THIS_MODULE,
+	.open     = picolcd_debug_reset_open,
+	.read     = seq_read,
+	.llseek   = seq_lseek,
+	.write    = picolcd_debug_reset_write,
+	.release  = single_release,
+};
+
+/*
+ * The "eeprom" file
+ */
+static int picolcd_debug_eeprom_open(struct inode *i, struct file *f)
+{
+	f->private_data = i->i_private;
+	return 0;
+}
+
+static ssize_t picolcd_debug_eeprom_read(struct file *f, char __user *u,
+		size_t s, loff_t *off)
+{
+	struct picolcd_data *data = f->private_data;
+	struct picolcd_pending *resp;
+	u8 raw_data[3];
+	ssize_t ret = -EIO;
+
+	if (s == 0)
+		return -EINVAL;
+	if (*off > 0x0ff)
+		return 0;
+
+	/* prepare buffer with info about what we want to read (addr & len) */
+	raw_data[0] = *off & 0xff;
+	raw_data[1] = (*off >> 8) && 0xff;
+	raw_data[2] = s < 20 ? s : 20;
+	if (*off + raw_data[2] > 0xff)
+		raw_data[2] = 0x100 - *off;
+	resp = picolcd_send_and_wait(data->hdev, REPORT_EE_READ, raw_data,
+			sizeof(raw_data));
+	if (!resp)
+		return -EIO;
+
+	if (resp->in_report && resp->in_report->id == REPORT_EE_DATA) {
+		/* successful read :) */
+		ret = resp->raw_data[2];
+		if (ret > s)
+			ret = s;
+		if (copy_to_user(u, resp->raw_data+3, ret))
+			ret = -EFAULT;
+		else
+			*off += ret;
+	} /* anything else is some kind of IO error */
+
+	kfree(resp);
+	return ret;
+}
+
+static ssize_t picolcd_debug_eeprom_write(struct file *f, const char __user *u,
+		size_t s, loff_t *off)
+{
+	struct picolcd_data *data = f->private_data;
+	struct picolcd_pending *resp;
+	ssize_t ret = -EIO;
+	u8 raw_data[23];
+
+	if (s == 0)
+		return -EINVAL;
+	if (*off > 0x0ff)
+		return -ENOSPC;
+
+	memset(raw_data, 0, sizeof(raw_data));
+	raw_data[0] = *off & 0xff;
+	raw_data[1] = (*off >> 8) && 0xff;
+	raw_data[2] = s < 20 ? s : 20;
+	if (*off + raw_data[2] > 0xff)
+		raw_data[2] = 0x100 - *off;
+
+	if (copy_from_user(raw_data+3, u, raw_data[2]))
+		return -EFAULT;
+	resp = picolcd_send_and_wait(data->hdev, REPORT_EE_WRITE, raw_data,
+			sizeof(raw_data));
+
+	if (!resp)
+		return -EIO;
+
+	if (resp->in_report && resp->in_report->id == REPORT_EE_DATA) {
+		/* check if written data matches */
+		if (memcmp(raw_data, resp->raw_data, 3+raw_data[2]) == 0) {
+			*off += raw_data[2];
+			ret = raw_data[2];
+		}
+	}
+	kfree(resp);
+	return ret;
+}
+
+/*
+ * Notes:
+ * - read/write happens in chunks of at most 20 bytes, it's up to userspace
+ *   to loop in order to get more data.
+ * - on write errors on otherwise correct write request the bytes
+ *   that should have been written are in undefined state.
+ */
+static const struct file_operations picolcd_debug_eeprom_fops = {
+	.owner    = THIS_MODULE,
+	.open     = picolcd_debug_eeprom_open,
+	.read     = picolcd_debug_eeprom_read,
+	.write    = picolcd_debug_eeprom_write,
+	.llseek   = generic_file_llseek,
+};
+
+/*
+ * The "flash" file
+ */
+static int picolcd_debug_flash_open(struct inode *i, struct file *f)
+{
+	f->private_data = i->i_private;
+	return 0;
+}
+
+/* record a flash address to buf (bounds check to be done by caller) */
+static int _picolcd_flash_setaddr(struct picolcd_data *data, u8 *buf, long off)
+{
+	buf[0] = off & 0xff;
+	buf[1] = (off >> 8) & 0xff;
+	if (data->addr_sz == 3)
+		buf[2] = (off >> 16) & 0xff;
+	return data->addr_sz == 2 ? 2 : 3;
+}
+
+/* read a given size of data (bounds check to be done by caller) */
+static ssize_t _picolcd_flash_read(struct picolcd_data *data, int report_id,
+		char __user *u, size_t s, loff_t *off)
+{
+	struct picolcd_pending *resp;
+	u8 raw_data[4];
+	ssize_t ret = 0;
+	int len_off, err = -EIO;
+
+	while (s > 0) {
+		err = -EIO;
+		len_off = _picolcd_flash_setaddr(data, raw_data, *off);
+		raw_data[len_off] = s > 32 ? 32 : s;
+		resp = picolcd_send_and_wait(data->hdev, report_id, raw_data, len_off+1);
+		if (!resp || !resp->in_report)
+			goto skip;
+		if (resp->in_report->id == REPORT_MEMORY ||
+			resp->in_report->id == REPORT_BL_READ_MEMORY) {
+			if (memcmp(raw_data, resp->raw_data, len_off+1) != 0)
+				goto skip;
+			if (copy_to_user(u+ret, resp->raw_data+len_off+1, raw_data[len_off])) {
+				err = -EFAULT;
+				goto skip;
+			}
+			*off += raw_data[len_off];
+			s    -= raw_data[len_off];
+			ret  += raw_data[len_off];
+			err   = 0;
+		}
+skip:
+		kfree(resp);
+		if (err)
+			return ret > 0 ? ret : err;
+	}
+	return ret;
+}
+
+static ssize_t picolcd_debug_flash_read(struct file *f, char __user *u,
+		size_t s, loff_t *off)
+{
+	struct picolcd_data *data = f->private_data;
+
+	if (s == 0)
+		return -EINVAL;
+	if (*off > 0x05fff)
+		return 0;
+	if (*off + s > 0x05fff)
+		s = 0x06000 - *off;
+
+	if (data->status & PICOLCD_BOOTLOADER)
+		return _picolcd_flash_read(data, REPORT_BL_READ_MEMORY, u, s, off);
+	else
+		return _picolcd_flash_read(data, REPORT_READ_MEMORY, u, s, off);
+}
+
+/* erase block aligned to 64bytes boundary */
+static ssize_t _picolcd_flash_erase64(struct picolcd_data *data, int report_id,
+		loff_t *off)
+{
+	struct picolcd_pending *resp;
+	u8 raw_data[3];
+	int len_off;
+	ssize_t ret = -EIO;
+
+	if (*off & 0x3f)
+		return -EINVAL;
+
+	len_off = _picolcd_flash_setaddr(data, raw_data, *off);
+	resp = picolcd_send_and_wait(data->hdev, report_id, raw_data, len_off);
+	if (!resp || !resp->in_report)
+		goto skip;
+	if (resp->in_report->id == REPORT_MEMORY ||
+		resp->in_report->id == REPORT_BL_ERASE_MEMORY) {
+		if (memcmp(raw_data, resp->raw_data, len_off) != 0)
+			goto skip;
+		ret = 0;
+	}
+skip:
+	kfree(resp);
+	return ret;
+}
+
+/* write a given size of data (bounds check to be done by caller) */
+static ssize_t _picolcd_flash_write(struct picolcd_data *data, int report_id,
+		const char __user *u, size_t s, loff_t *off)
+{
+	struct picolcd_pending *resp;
+	u8 raw_data[36];
+	ssize_t ret = 0;
+	int len_off, err = -EIO;
+
+	while (s > 0) {
+		err = -EIO;
+		len_off = _picolcd_flash_setaddr(data, raw_data, *off);
+		raw_data[len_off] = s > 32 ? 32 : s;
+		if (copy_from_user(raw_data+len_off+1, u, raw_data[len_off])) {
+			err = -EFAULT;
+			break;
+		}
+		resp = picolcd_send_and_wait(data->hdev, report_id, raw_data,
+				len_off+1+raw_data[len_off]);
+		if (!resp || !resp->in_report)
+			goto skip;
+		if (resp->in_report->id == REPORT_MEMORY ||
+			resp->in_report->id == REPORT_BL_WRITE_MEMORY) {
+			if (memcmp(raw_data, resp->raw_data, len_off+1+raw_data[len_off]) != 0)
+				goto skip;
+			*off += raw_data[len_off];
+			s    -= raw_data[len_off];
+			ret  += raw_data[len_off];
+			err   = 0;
+		}
+skip:
+		kfree(resp);
+		if (err)
+			break;
+	}
+	return ret > 0 ? ret : err;
+}
+
+static ssize_t picolcd_debug_flash_write(struct file *f, const char __user *u,
+		size_t s, loff_t *off)
+{
+	struct picolcd_data *data = f->private_data;
+	ssize_t err, ret = 0;
+	int report_erase, report_write;
+
+	if (s == 0)
+		return -EINVAL;
+	if (*off > 0x5fff)
+		return -ENOSPC;
+	if (s & 0x3f)
+		return -EINVAL;
+	if (*off & 0x3f)
+		return -EINVAL;
+
+	if (data->status & PICOLCD_BOOTLOADER) {
+		report_erase = REPORT_BL_ERASE_MEMORY;
+		report_write = REPORT_BL_WRITE_MEMORY;
+	} else {
+		report_erase = REPORT_ERASE_MEMORY;
+		report_write = REPORT_WRITE_MEMORY;
+	}
+	mutex_lock(&data->mutex_flash);
+	while (s > 0) {
+		err = _picolcd_flash_erase64(data, report_erase, off);
+		if (err)
+			break;
+		err = _picolcd_flash_write(data, report_write, u, 64, off);
+		if (err < 0)
+			break;
+		ret += err;
+		*off += err;
+		s -= err;
+		if (err != 64)
+			break;
+	}
+	mutex_unlock(&data->mutex_flash);
+	return ret > 0 ? ret : err;
+}
+
+/*
+ * Notes:
+ * - concurrent writing is prevented by mutex and all writes must be
+ *   n*64 bytes and 64-byte aligned, each write being preceeded by an
+ *   ERASE which erases a 64byte block.
+ *   If less than requested was written or an error is returned for an
+ *   otherwise correct write request the next 64-byte block which should
+ *   have been written is in undefined state (mostly: original, erased,
+ *   (half-)written with write error)
+ * - reading can happend without special restriction
+ */
+static const struct file_operations picolcd_debug_flash_fops = {
+	.owner    = THIS_MODULE,
+	.open     = picolcd_debug_flash_open,
+	.read     = picolcd_debug_flash_read,
+	.write    = picolcd_debug_flash_write,
+	.llseek   = generic_file_llseek,
+};
+
+
+/*
+ * Helper code for HID report level dumping/debugging
+ */
+static const char *error_codes[] = {
+	"success", "parameter missing", "data_missing", "block readonly",
+	"block not erasable", "block too big", "section overflow",
+	"invalid command length", "invalid data length",
+};
+
+static void dump_buff_as_hex(char *dst, size_t dst_sz, const u8 *data,
+		const size_t data_len)
+{
+	int i, j;
+	for (i = j = 0; i < data_len && j + 3 < dst_sz; i++) {
+		dst[j++] = hex_asc[(data[i] >> 4) & 0x0f];
+		dst[j++] = hex_asc[data[i] & 0x0f];
+		dst[j++] = ' ';
+	}
+	if (j < dst_sz) {
+		dst[j--] = '\0';
+		dst[j] = '\n';
+	} else
+		dst[j] = '\0';
+}
+
+static void picolcd_debug_out_report(struct picolcd_data *data,
+		struct hid_device *hdev, struct hid_report *report)
+{
+	u8 raw_data[70];
+	int raw_size = (report->size >> 3) + 1;
+	char *buff;
+#define BUFF_SZ 256
+
+	/* Avoid unnecessary overhead if debugfs is disabled */
+	if (!hdev->debug_events)
+		return;
+
+	buff = kmalloc(BUFF_SZ, GFP_ATOMIC);
+	if (!buff)
+		return;
+
+	snprintf(buff, BUFF_SZ, "\nout report %d (size %d) =  ",
+			report->id, raw_size);
+	hid_debug_event(hdev, buff);
+	if (raw_size + 5 > sizeof(raw_data)) {
+		hid_debug_event(hdev, " TOO BIG\n");
+		return;
+	} else {
+		raw_data[0] = report->id;
+		hid_output_report(report, raw_data);
+		dump_buff_as_hex(buff, BUFF_SZ, raw_data, raw_size);
+		hid_debug_event(hdev, buff);
+	}
+
+	switch (report->id) {
+	case REPORT_LED_STATE:
+		/* 1 data byte with GPO state */
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_LED_STATE", report->id, raw_size-1);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tGPO state: 0x%02x\n", raw_data[1]);
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_BRIGHTNESS:
+		/* 1 data byte with brightness */
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_BRIGHTNESS", report->id, raw_size-1);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tBrightness: 0x%02x\n", raw_data[1]);
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_CONTRAST:
+		/* 1 data byte with contrast */
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_CONTRAST", report->id, raw_size-1);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tContrast: 0x%02x\n", raw_data[1]);
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_RESET:
+		/* 2 data bytes with reset duration in ms */
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_RESET", report->id, raw_size-1);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tDuration: 0x%02x%02x (%dms)\n",
+				raw_data[2], raw_data[1], raw_data[2] << 8 | raw_data[1]);
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_LCD_CMD:
+		/* 63 data bytes with LCD commands */
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_LCD_CMD", report->id, raw_size-1);
+		hid_debug_event(hdev, buff);
+		/* TODO: format decoding */
+		break;
+	case REPORT_LCD_DATA:
+		/* 63 data bytes with LCD data */
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_LCD_CMD", report->id, raw_size-1);
+		/* TODO: format decoding */
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_LCD_CMD_DATA:
+		/* 63 data bytes with LCD commands and data */
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_LCD_CMD", report->id, raw_size-1);
+		/* TODO: format decoding */
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_EE_READ:
+		/* 3 data bytes with read area description */
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_EE_READ", report->id, raw_size-1);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n",
+				raw_data[2], raw_data[1]);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]);
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_EE_WRITE:
+		/* 3+1..20 data bytes with write area description */
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_EE_WRITE", report->id, raw_size-1);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n",
+				raw_data[2], raw_data[1]);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]);
+		hid_debug_event(hdev, buff);
+		if (raw_data[3] == 0) {
+			snprintf(buff, BUFF_SZ, "\tNo data\n");
+		} else if (raw_data[3] + 4 <= raw_size) {
+			snprintf(buff, BUFF_SZ, "\tData: ");
+			hid_debug_event(hdev, buff);
+			dump_buff_as_hex(buff, BUFF_SZ, raw_data+4, raw_data[3]);
+		} else {
+			snprintf(buff, BUFF_SZ, "\tData overflowed\n");
+		}
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_ERASE_MEMORY:
+	case REPORT_BL_ERASE_MEMORY:
+		/* 3 data bytes with pointer inside erase block */
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_ERASE_MEMORY", report->id, raw_size-1);
+		hid_debug_event(hdev, buff);
+		switch (data->addr_sz) {
+		case 2:
+			snprintf(buff, BUFF_SZ, "\tAddress inside 64 byte block: 0x%02x%02x\n",
+					raw_data[2], raw_data[1]);
+			break;
+		case 3:
+			snprintf(buff, BUFF_SZ, "\tAddress inside 64 byte block: 0x%02x%02x%02x\n",
+					raw_data[3], raw_data[2], raw_data[1]);
+			break;
+		default:
+			snprintf(buff, BUFF_SZ, "\tNot supported\n");
+		}
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_READ_MEMORY:
+	case REPORT_BL_READ_MEMORY:
+		/* 4 data bytes with read area description */
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_READ_MEMORY", report->id, raw_size-1);
+		hid_debug_event(hdev, buff);
+		switch (data->addr_sz) {
+		case 2:
+			snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n",
+					raw_data[2], raw_data[1]);
+			hid_debug_event(hdev, buff);
+			snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]);
+			break;
+		case 3:
+			snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x%02x\n",
+					raw_data[3], raw_data[2], raw_data[1]);
+			hid_debug_event(hdev, buff);
+			snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[4]);
+			break;
+		default:
+			snprintf(buff, BUFF_SZ, "\tNot supported\n");
+		}
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_WRITE_MEMORY:
+	case REPORT_BL_WRITE_MEMORY:
+		/* 4+1..32 data bytes with write adrea description */
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_WRITE_MEMORY", report->id, raw_size-1);
+		hid_debug_event(hdev, buff);
+		switch (data->addr_sz) {
+		case 2:
+			snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n",
+					raw_data[2], raw_data[1]);
+			hid_debug_event(hdev, buff);
+			snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]);
+			hid_debug_event(hdev, buff);
+			if (raw_data[3] == 0) {
+				snprintf(buff, BUFF_SZ, "\tNo data\n");
+			} else if (raw_data[3] + 4 <= raw_size) {
+				snprintf(buff, BUFF_SZ, "\tData: ");
+				hid_debug_event(hdev, buff);
+				dump_buff_as_hex(buff, BUFF_SZ, raw_data+4, raw_data[3]);
+			} else {
+				snprintf(buff, BUFF_SZ, "\tData overflowed\n");
+			}
+			break;
+		case 3:
+			snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x%02x\n",
+					raw_data[3], raw_data[2], raw_data[1]);
+			hid_debug_event(hdev, buff);
+			snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[4]);
+			hid_debug_event(hdev, buff);
+			if (raw_data[4] == 0) {
+				snprintf(buff, BUFF_SZ, "\tNo data\n");
+			} else if (raw_data[4] + 5 <= raw_size) {
+				snprintf(buff, BUFF_SZ, "\tData: ");
+				hid_debug_event(hdev, buff);
+				dump_buff_as_hex(buff, BUFF_SZ, raw_data+5, raw_data[4]);
+			} else {
+				snprintf(buff, BUFF_SZ, "\tData overflowed\n");
+			}
+			break;
+		default:
+			snprintf(buff, BUFF_SZ, "\tNot supported\n");
+		}
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_SPLASH_RESTART:
+		/* TODO */
+		break;
+	case REPORT_EXIT_KEYBOARD:
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_EXIT_KEYBOARD", report->id, raw_size-1);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tRestart delay: %dms (0x%02x%02x)\n",
+				raw_data[1] | (raw_data[2] << 8),
+				raw_data[2], raw_data[1]);
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_VERSION:
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_VERSION", report->id, raw_size-1);
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_DEVID:
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_DEVID", report->id, raw_size-1);
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_SPLASH_SIZE:
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_SPLASH_SIZE", report->id, raw_size-1);
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_HOOK_VERSION:
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_HOOK_VERSION", report->id, raw_size-1);
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_EXIT_FLASHER:
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"REPORT_VERSION", report->id, raw_size-1);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tRestart delay: %dms (0x%02x%02x)\n",
+				raw_data[1] | (raw_data[2] << 8),
+				raw_data[2], raw_data[1]);
+		hid_debug_event(hdev, buff);
+		break;
+	default:
+		snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+			"<unknown>", report->id, raw_size-1);
+		hid_debug_event(hdev, buff);
+		break;
+	}
+	wake_up_interruptible(&hdev->debug_wait);
+	kfree(buff);
+}
+
+static void picolcd_debug_raw_event(struct picolcd_data *data,
+		struct hid_device *hdev, struct hid_report *report,
+		u8 *raw_data, int size)
+{
+	char *buff;
+
+#define BUFF_SZ 256
+	/* Avoid unnecessary overhead if debugfs is disabled */
+	if (!hdev->debug_events)
+		return;
+
+	buff = kmalloc(BUFF_SZ, GFP_ATOMIC);
+	if (!buff)
+		return;
+
+	switch (report->id) {
+	case REPORT_ERROR_CODE:
+		/* 2 data bytes with affected report and error code */
+		snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+			"REPORT_ERROR_CODE", report->id, size-1);
+		hid_debug_event(hdev, buff);
+		if (raw_data[2] < ARRAY_SIZE(error_codes))
+			snprintf(buff, BUFF_SZ, "\tError code 0x%02x (%s) in reply to report 0x%02x\n",
+					raw_data[2], error_codes[raw_data[2]], raw_data[1]);
+		else
+			snprintf(buff, BUFF_SZ, "\tError code 0x%02x in reply to report 0x%02x\n",
+					raw_data[2], raw_data[1]);
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_KEY_STATE:
+		/* 2 data bytes with key state */
+		snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+			"REPORT_KEY_STATE", report->id, size-1);
+		hid_debug_event(hdev, buff);
+		if (raw_data[1] == 0)
+			snprintf(buff, BUFF_SZ, "\tNo key pressed\n");
+		else if (raw_data[2] == 0)
+			snprintf(buff, BUFF_SZ, "\tOne key pressed: 0x%02x (%d)\n",
+					raw_data[1], raw_data[1]);
+		else
+			snprintf(buff, BUFF_SZ, "\tTwo keys pressed: 0x%02x (%d), 0x%02x (%d)\n",
+					raw_data[1], raw_data[1], raw_data[2], raw_data[2]);
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_IR_DATA:
+		/* Up to 20 byes of IR scancode data */
+		snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+			"REPORT_IR_DATA", report->id, size-1);
+		hid_debug_event(hdev, buff);
+		if (raw_data[1] == 0) {
+			snprintf(buff, BUFF_SZ, "\tUnexpectedly 0 data length\n");
+			hid_debug_event(hdev, buff);
+		} else if (raw_data[1] + 1 <= size) {
+			snprintf(buff, BUFF_SZ, "\tData length: %d\n\tIR Data: ",
+					raw_data[1]-1);
+			hid_debug_event(hdev, buff);
+			dump_buff_as_hex(buff, BUFF_SZ, raw_data+2, raw_data[1]-1);
+			hid_debug_event(hdev, buff);
+		} else {
+			snprintf(buff, BUFF_SZ, "\tOverflowing data length: %d\n",
+					raw_data[1]-1);
+			hid_debug_event(hdev, buff);
+		}
+		break;
+	case REPORT_EE_DATA:
+		/* Data buffer in response to REPORT_EE_READ or REPORT_EE_WRITE */
+		snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+			"REPORT_EE_DATA", report->id, size-1);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n",
+				raw_data[2], raw_data[1]);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]);
+		hid_debug_event(hdev, buff);
+		if (raw_data[3] == 0) {
+			snprintf(buff, BUFF_SZ, "\tNo data\n");
+			hid_debug_event(hdev, buff);
+		} else if (raw_data[3] + 4 <= size) {
+			snprintf(buff, BUFF_SZ, "\tData: ");
+			hid_debug_event(hdev, buff);
+			dump_buff_as_hex(buff, BUFF_SZ, raw_data+4, raw_data[3]);
+			hid_debug_event(hdev, buff);
+		} else {
+			snprintf(buff, BUFF_SZ, "\tData overflowed\n");
+			hid_debug_event(hdev, buff);
+		}
+		break;
+	case REPORT_MEMORY:
+		/* Data buffer in response to REPORT_READ_MEMORY or REPORT_WRTIE_MEMORY */
+		snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+			"REPORT_MEMORY", report->id, size-1);
+		hid_debug_event(hdev, buff);
+		switch (data->addr_sz) {
+		case 2:
+			snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n",
+					raw_data[2], raw_data[1]);
+			hid_debug_event(hdev, buff);
+			snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]);
+			hid_debug_event(hdev, buff);
+			if (raw_data[3] == 0) {
+				snprintf(buff, BUFF_SZ, "\tNo data\n");
+			} else if (raw_data[3] + 4 <= size) {
+				snprintf(buff, BUFF_SZ, "\tData: ");
+				hid_debug_event(hdev, buff);
+				dump_buff_as_hex(buff, BUFF_SZ, raw_data+4, raw_data[3]);
+			} else {
+				snprintf(buff, BUFF_SZ, "\tData overflowed\n");
+			}
+			break;
+		case 3:
+			snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x%02x\n",
+					raw_data[3], raw_data[2], raw_data[1]);
+			hid_debug_event(hdev, buff);
+			snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[4]);
+			hid_debug_event(hdev, buff);
+			if (raw_data[4] == 0) {
+				snprintf(buff, BUFF_SZ, "\tNo data\n");
+			} else if (raw_data[4] + 5 <= size) {
+				snprintf(buff, BUFF_SZ, "\tData: ");
+				hid_debug_event(hdev, buff);
+				dump_buff_as_hex(buff, BUFF_SZ, raw_data+5, raw_data[4]);
+			} else {
+				snprintf(buff, BUFF_SZ, "\tData overflowed\n");
+			}
+			break;
+		default:
+			snprintf(buff, BUFF_SZ, "\tNot supported\n");
+		}
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_VERSION:
+		snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+			"REPORT_VERSION", report->id, size-1);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tFirmware version: %d.%d\n",
+				raw_data[2], raw_data[1]);
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_BL_ERASE_MEMORY:
+		snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+			"REPORT_BL_ERASE_MEMORY", report->id, size-1);
+		hid_debug_event(hdev, buff);
+		/* TODO */
+		break;
+	case REPORT_BL_READ_MEMORY:
+		snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+			"REPORT_BL_READ_MEMORY", report->id, size-1);
+		hid_debug_event(hdev, buff);
+		/* TODO */
+		break;
+	case REPORT_BL_WRITE_MEMORY:
+		snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+			"REPORT_BL_WRITE_MEMORY", report->id, size-1);
+		hid_debug_event(hdev, buff);
+		/* TODO */
+		break;
+	case REPORT_DEVID:
+		snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+			"REPORT_DEVID", report->id, size-1);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tSerial: 0x%02x%02x%02x%02x\n",
+				raw_data[1], raw_data[2], raw_data[3], raw_data[4]);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tType: 0x%02x\n",
+				raw_data[5]);
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_SPLASH_SIZE:
+		snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+			"REPORT_SPLASH_SIZE", report->id, size-1);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tTotal splash space: %d\n",
+				(raw_data[2] << 8) | raw_data[1]);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tUsed splash space: %d\n",
+				(raw_data[4] << 8) | raw_data[3]);
+		hid_debug_event(hdev, buff);
+		break;
+	case REPORT_HOOK_VERSION:
+		snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+			"REPORT_HOOK_VERSION", report->id, size-1);
+		hid_debug_event(hdev, buff);
+		snprintf(buff, BUFF_SZ, "\tFirmware version: %d.%d\n",
+				raw_data[1], raw_data[2]);
+		hid_debug_event(hdev, buff);
+		break;
+	default:
+		snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+			"<unknown>", report->id, size-1);
+		hid_debug_event(hdev, buff);
+		break;
+	}
+	wake_up_interruptible(&hdev->debug_wait);
+	kfree(buff);
+}
+
+static void picolcd_init_devfs(struct picolcd_data *data,
+		struct hid_report *eeprom_r, struct hid_report *eeprom_w,
+		struct hid_report *flash_r, struct hid_report *flash_w,
+		struct hid_report *reset)
+{
+	struct hid_device *hdev = data->hdev;
+
+	mutex_init(&data->mutex_flash);
+
+	/* reset */
+	if (reset)
+		data->debug_reset = debugfs_create_file("reset", 0600,
+				hdev->debug_dir, data, &picolcd_debug_reset_fops);
+
+	/* eeprom */
+	if (eeprom_r || eeprom_w)
+		data->debug_eeprom = debugfs_create_file("eeprom",
+			(eeprom_w ? S_IWUSR : 0) | (eeprom_r ? S_IRUSR : 0),
+			hdev->debug_dir, data, &picolcd_debug_eeprom_fops);
+
+	/* flash */
+	if (flash_r && flash_r->maxfield == 1 && flash_r->field[0]->report_size == 8)
+		data->addr_sz = flash_r->field[0]->report_count - 1;
+	else
+		data->addr_sz = -1;
+	if (data->addr_sz == 2 || data->addr_sz == 3) {
+		data->debug_flash = debugfs_create_file("flash",
+			(flash_w ? S_IWUSR : 0) | (flash_r ? S_IRUSR : 0),
+			hdev->debug_dir, data, &picolcd_debug_flash_fops);
+	} else if (flash_r || flash_w)
+		dev_warn(&hdev->dev, "Unexpected FLASH access reports, "
+				"please submit rdesc for review\n");
+}
+
+static void picolcd_exit_devfs(struct picolcd_data *data)
+{
+	struct dentry *dent;
+
+	dent = data->debug_reset;
+	data->debug_reset = NULL;
+	if (dent)
+		debugfs_remove(dent);
+	dent = data->debug_eeprom;
+	data->debug_eeprom = NULL;
+	if (dent)
+		debugfs_remove(dent);
+	dent = data->debug_flash;
+	data->debug_flash = NULL;
+	if (dent)
+		debugfs_remove(dent);
+	mutex_destroy(&data->mutex_flash);
+}
+#else
+static inline void picolcd_debug_raw_event(struct picolcd_data *data,
+		struct hid_device *hdev, struct hid_report *report,
+		u8 *raw_data, int size)
+{
+}
+static inline void picolcd_init_devfs(struct picolcd_data *data,
+		struct hid_report *eeprom_r, struct hid_report *eeprom_w,
+		struct hid_report *flash_r, struct hid_report *flash_w,
+		struct hid_report *reset)
+{
+}
+static inline void picolcd_exit_devfs(struct picolcd_data *data)
+{
+}
+#endif /* CONFIG_DEBUG_FS */
+
+/*
+ * Handle raw report as sent by device
+ */
+static int picolcd_raw_event(struct hid_device *hdev,
+		struct hid_report *report, u8 *raw_data, int size)
+{
+	struct picolcd_data *data = hid_get_drvdata(hdev);
+	unsigned long flags;
+	int ret = 0;
+
+	if (!data)
+		return 1;
+
+	if (report->id == REPORT_KEY_STATE) {
+		if (data->input_keys)
+			ret = picolcd_raw_keypad(data, report, raw_data+1, size-1);
+	} else if (report->id == REPORT_IR_DATA) {
+		if (data->input_cir)
+			ret = picolcd_raw_cir(data, report, raw_data+1, size-1);
+	} else {
+		spin_lock_irqsave(&data->lock, flags);
+		/*
+		 * We let the caller of picolcd_send_and_wait() check if the
+		 * report we got is one of the expected ones or not.
+		 */
+		if (data->pending) {
+			memcpy(data->pending->raw_data, raw_data+1, size-1);
+			data->pending->raw_size  = size-1;
+			data->pending->in_report = report;
+			complete(&data->pending->ready);
+		}
+		spin_unlock_irqrestore(&data->lock, flags);
+	}
+
+	picolcd_debug_raw_event(data, hdev, report, raw_data, size);
+	return 1;
+}
+
+#ifdef CONFIG_PM
+static int picolcd_suspend(struct hid_device *hdev, pm_message_t message)
+{
+	if (message.event & PM_EVENT_AUTO)
+		return 0;
+
+	picolcd_suspend_backlight(hid_get_drvdata(hdev));
+	dbg_hid(PICOLCD_NAME " device ready for suspend\n");
+	return 0;
+}
+
+static int picolcd_resume(struct hid_device *hdev)
+{
+	int ret;
+	ret = picolcd_resume_backlight(hid_get_drvdata(hdev));
+	if (ret)
+		dbg_hid(PICOLCD_NAME " restoring backlight failed: %d\n", ret);
+	return 0;
+}
+
+static int picolcd_reset_resume(struct hid_device *hdev)
+{
+	int ret;
+	ret = picolcd_reset(hdev);
+	if (ret)
+		dbg_hid(PICOLCD_NAME " resetting our device failed: %d\n", ret);
+	ret = picolcd_fb_reset(hid_get_drvdata(hdev), 0);
+	if (ret)
+		dbg_hid(PICOLCD_NAME " restoring framebuffer content failed: %d\n", ret);
+	ret = picolcd_resume_lcd(hid_get_drvdata(hdev));
+	if (ret)
+		dbg_hid(PICOLCD_NAME " restoring lcd failed: %d\n", ret);
+	ret = picolcd_resume_backlight(hid_get_drvdata(hdev));
+	if (ret)
+		dbg_hid(PICOLCD_NAME " restoring backlight failed: %d\n", ret);
+	picolcd_leds_set(hid_get_drvdata(hdev));
+	return 0;
+}
+#endif
+
+/* initialize keypad input device */
+static int picolcd_init_keys(struct picolcd_data *data,
+		struct hid_report *report)
+{
+	struct hid_device *hdev = data->hdev;
+	struct input_dev *idev;
+	int error, i;
+
+	if (!report)
+		return -ENODEV;
+	if (report->maxfield != 1 || report->field[0]->report_count != 2 ||
+			report->field[0]->report_size != 8) {
+		dev_err(&hdev->dev, "unsupported KEY_STATE report");
+		return -EINVAL;
+	}
+
+	idev = input_allocate_device();
+	if (idev == NULL) {
+		dev_err(&hdev->dev, "failed to allocate input device");
+		return -ENOMEM;
+	}
+	input_set_drvdata(idev, hdev);
+	memcpy(data->keycode, def_keymap, sizeof(def_keymap));
+	idev->name = hdev->name;
+	idev->phys = hdev->phys;
+	idev->uniq = hdev->uniq;
+	idev->id.bustype = hdev->bus;
+	idev->id.vendor  = hdev->vendor;
+	idev->id.product = hdev->product;
+	idev->id.version = hdev->version;
+	idev->dev.parent = hdev->dev.parent;
+	idev->keycode     = &data->keycode;
+	idev->keycodemax  = PICOLCD_KEYS;
+	idev->keycodesize = sizeof(data->keycode[0]);
+	input_set_capability(idev, EV_MSC, MSC_SCAN);
+	set_bit(EV_REP, idev->evbit);
+	for (i = 0; i < PICOLCD_KEYS; i++)
+		input_set_capability(idev, EV_KEY, data->keycode[i]);
+	error = input_register_device(idev);
+	if (error) {
+		dev_err(&hdev->dev, "error registering the input device");
+		input_free_device(idev);
+		return error;
+	}
+	data->input_keys = idev;
+	return 0;
+}
+
+static void picolcd_exit_keys(struct picolcd_data *data)
+{
+	struct input_dev *idev = data->input_keys;
+
+	data->input_keys = NULL;
+	if (idev)
+		input_unregister_device(idev);
+}
+
+/* initialize CIR input device */
+static inline int picolcd_init_cir(struct picolcd_data *data, struct hid_report *report)
+{
+	/* support not implemented yet */
+	return 0;
+}
+
+static inline void picolcd_exit_cir(struct picolcd_data *data)
+{
+}
+
+static int picolcd_probe_lcd(struct hid_device *hdev, struct picolcd_data *data)
+{
+	int error;
+
+	error = picolcd_check_version(hdev);
+	if (error)
+		return error;
+
+	if (data->version[0] != 0 && data->version[1] != 3)
+		dev_info(&hdev->dev, "Device with untested firmware revision, "
+				"please submit /sys/kernel/debug/hid/%s/rdesc for this device.\n",
+				dev_name(&hdev->dev));
+
+	/* Setup keypad input device */
+	error = picolcd_init_keys(data, picolcd_in_report(REPORT_KEY_STATE, hdev));
+	if (error)
+		goto err;
+
+	/* Setup CIR input device */
+	error = picolcd_init_cir(data, picolcd_in_report(REPORT_IR_DATA, hdev));
+	if (error)
+		goto err;
+
+	/* Set up the framebuffer device */
+	error = picolcd_init_framebuffer(data);
+	if (error)
+		goto err;
+
+	/* Setup lcd class device */
+	error = picolcd_init_lcd(data, picolcd_out_report(REPORT_CONTRAST, hdev));
+	if (error)
+		goto err;
+
+	/* Setup backlight class device */
+	error = picolcd_init_backlight(data, picolcd_out_report(REPORT_BRIGHTNESS, hdev));
+	if (error)
+		goto err;
+
+	/* Setup the LED class devices */
+	error = picolcd_init_leds(data, picolcd_out_report(REPORT_LED_STATE, hdev));
+	if (error)
+		goto err;
+
+	picolcd_init_devfs(data, picolcd_out_report(REPORT_EE_READ, hdev),
+			picolcd_out_report(REPORT_EE_WRITE, hdev),
+			picolcd_out_report(REPORT_READ_MEMORY, hdev),
+			picolcd_out_report(REPORT_WRITE_MEMORY, hdev),
+			picolcd_out_report(REPORT_RESET, hdev));
+	return 0;
+err:
+	picolcd_exit_leds(data);
+	picolcd_exit_backlight(data);
+	picolcd_exit_lcd(data);
+	picolcd_exit_framebuffer(data);
+	picolcd_exit_cir(data);
+	picolcd_exit_keys(data);
+	return error;
+}
+
+static int picolcd_probe_bootloader(struct hid_device *hdev, struct picolcd_data *data)
+{
+	int error;
+
+	error = picolcd_check_version(hdev);
+	if (error)
+		return error;
+
+	if (data->version[0] != 1 && data->version[1] != 0)
+		dev_info(&hdev->dev, "Device with untested bootloader revision, "
+				"please submit /sys/kernel/debug/hid/%s/rdesc for this device.\n",
+				dev_name(&hdev->dev));
+
+	picolcd_init_devfs(data, NULL, NULL,
+			picolcd_out_report(REPORT_BL_READ_MEMORY, hdev),
+			picolcd_out_report(REPORT_BL_WRITE_MEMORY, hdev), NULL);
+	return 0;
+}
+
+static int picolcd_probe(struct hid_device *hdev,
+		     const struct hid_device_id *id)
+{
+	struct picolcd_data *data;
+	int error = -ENOMEM;
+
+	dbg_hid(PICOLCD_NAME " hardware probe...\n");
+
+	/*
+	 * Let's allocate the picolcd data structure, set some reasonable
+	 * defaults, and associate it with the device
+	 */
+	data = kzalloc(sizeof(struct picolcd_data), GFP_KERNEL);
+	if (data == NULL) {
+		dev_err(&hdev->dev, "can't allocate space for Minibox PicoLCD device data\n");
+		error = -ENOMEM;
+		goto err_no_cleanup;
+	}
+
+	spin_lock_init(&data->lock);
+	mutex_init(&data->mutex);
+	data->hdev = hdev;
+	data->opmode_delay = 5000;
+	if (hdev->product == USB_DEVICE_ID_PICOLCD_BOOTLOADER)
+		data->status |= PICOLCD_BOOTLOADER;
+	hid_set_drvdata(hdev, data);
+
+	/* Parse the device reports and start it up */
+	error = hid_parse(hdev);
+	if (error) {
+		dev_err(&hdev->dev, "device report parse failed\n");
+		goto err_cleanup_data;
+	}
+
+	/* We don't use hidinput but hid_hw_start() fails if nothing is
+	 * claimed. So spoof claimed input. */
+	hdev->claimed = HID_CLAIMED_INPUT;
+	error = hid_hw_start(hdev, 0);
+	hdev->claimed = 0;
+	if (error) {
+		dev_err(&hdev->dev, "hardware start failed\n");
+		goto err_cleanup_data;
+	}
+
+	error = hdev->ll_driver->open(hdev);
+	if (error) {
+		dev_err(&hdev->dev, "failed to open input interrupt pipe for key and IR events\n");
+		goto err_cleanup_hid_hw;
+	}
+
+	error = device_create_file(&hdev->dev, &dev_attr_operation_mode_delay);
+	if (error) {
+		dev_err(&hdev->dev, "failed to create sysfs attributes\n");
+		goto err_cleanup_hid_ll;
+	}
+
+	error = device_create_file(&hdev->dev, &dev_attr_operation_mode);
+	if (error) {
+		dev_err(&hdev->dev, "failed to create sysfs attributes\n");
+		goto err_cleanup_sysfs1;
+	}
+
+	if (data->status & PICOLCD_BOOTLOADER)
+		error = picolcd_probe_bootloader(hdev, data);
+	else
+		error = picolcd_probe_lcd(hdev, data);
+	if (error)
+		goto err_cleanup_sysfs2;
+
+	dbg_hid(PICOLCD_NAME " activated and initialized\n");
+	return 0;
+
+err_cleanup_sysfs2:
+	device_remove_file(&hdev->dev, &dev_attr_operation_mode);
+err_cleanup_sysfs1:
+	device_remove_file(&hdev->dev, &dev_attr_operation_mode_delay);
+err_cleanup_hid_ll:
+	hdev->ll_driver->close(hdev);
+err_cleanup_hid_hw:
+	hid_hw_stop(hdev);
+err_cleanup_data:
+	kfree(data);
+err_no_cleanup:
+	hid_set_drvdata(hdev, NULL);
+
+	return error;
+}
+
+static void picolcd_remove(struct hid_device *hdev)
+{
+	struct picolcd_data *data = hid_get_drvdata(hdev);
+	unsigned long flags;
+
+	dbg_hid(PICOLCD_NAME " hardware remove...\n");
+	spin_lock_irqsave(&data->lock, flags);
+	data->status |= PICOLCD_FAILED;
+	spin_unlock_irqrestore(&data->lock, flags);
+
+	picolcd_exit_devfs(data);
+	device_remove_file(&hdev->dev, &dev_attr_operation_mode);
+	device_remove_file(&hdev->dev, &dev_attr_operation_mode_delay);
+	hdev->ll_driver->close(hdev);
+	hid_hw_stop(hdev);
+	hid_set_drvdata(hdev, NULL);
+
+	/* Shortcut potential pending reply that will never arrive */
+	spin_lock_irqsave(&data->lock, flags);
+	if (data->pending)
+		complete(&data->pending->ready);
+	spin_unlock_irqrestore(&data->lock, flags);
+
+	/* Cleanup LED */
+	picolcd_exit_leds(data);
+	/* Clean up the framebuffer */
+	picolcd_exit_backlight(data);
+	picolcd_exit_lcd(data);
+	picolcd_exit_framebuffer(data);
+	/* Cleanup input */
+	picolcd_exit_cir(data);
+	picolcd_exit_keys(data);
+
+	mutex_destroy(&data->mutex);
+	/* Finally, clean up the picolcd data itself */
+	kfree(data);
+}
+
+static const struct hid_device_id picolcd_devices[] = {
+	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_PICOLCD) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_PICOLCD_BOOTLOADER) },
+	{ }
+};
+MODULE_DEVICE_TABLE(hid, picolcd_devices);
+
+static struct hid_driver picolcd_driver = {
+	.name =          "hid-picolcd",
+	.id_table =      picolcd_devices,
+	.probe =         picolcd_probe,
+	.remove =        picolcd_remove,
+	.raw_event =     picolcd_raw_event,
+#ifdef CONFIG_PM
+	.suspend =       picolcd_suspend,
+	.resume =        picolcd_resume,
+	.reset_resume =  picolcd_reset_resume,
+#endif
+};
+
+static int __init picolcd_init(void)
+{
+	return hid_register_driver(&picolcd_driver);
+}
+
+static void __exit picolcd_exit(void)
+{
+	hid_unregister_driver(&picolcd_driver);
+}
+
+module_init(picolcd_init);
+module_exit(picolcd_exit);
+MODULE_DESCRIPTION("Minibox graphics PicoLCD Driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/hid/hid-prodikeys.c b/drivers/hid/hid-prodikeys.c
new file mode 100644
index 0000000..845f428
--- /dev/null
+++ b/drivers/hid/hid-prodikeys.c
@@ -0,0 +1,910 @@
+/*
+ *  HID driver for the Prodikeys PC-MIDI Keyboard
+ *  providing midi & extra multimedia keys functionality
+ *
+ *  Copyright (c) 2009 Don Prince <dhprince.devel@yahoo.co.uk>
+ *
+ *  Controls for Octave Shift Up/Down, Channel, and
+ *  Sustain Duration available via sysfs.
+ *
+ */
+
+/*
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ */
+
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/usb.h>
+#include <linux/mutex.h>
+#include <linux/hid.h>
+#include <sound/core.h>
+#include <sound/initval.h>
+#include <sound/rawmidi.h>
+#include "usbhid/usbhid.h"
+#include "hid-ids.h"
+
+
+#define pk_debug(format, arg...) \
+	pr_debug("hid-prodikeys: " format "\n" , ## arg)
+#define pk_error(format, arg...) \
+	pr_err("hid-prodikeys: " format "\n" , ## arg)
+
+struct pcmidi_snd;
+
+struct pk_device {
+	unsigned long		quirks;
+
+	struct hid_device	*hdev;
+	struct pcmidi_snd	*pm; /* pcmidi device context */
+};
+
+struct pcmidi_snd;
+
+struct pcmidi_sustain {
+	unsigned long		in_use;
+	struct pcmidi_snd	*pm;
+	struct timer_list	timer;
+	unsigned char		status;
+	unsigned char		note;
+	unsigned char		velocity;
+};
+
+#define PCMIDI_SUSTAINED_MAX	32
+struct pcmidi_snd {
+	struct pk_device		*pk;
+	unsigned short			ifnum;
+	struct hid_report		*pcmidi_report6;
+	struct input_dev		*input_ep82;
+	unsigned short			midi_mode;
+	unsigned short			midi_sustain_mode;
+	unsigned short			midi_sustain;
+	unsigned short			midi_channel;
+	short				midi_octave;
+	struct pcmidi_sustain		sustained_notes[PCMIDI_SUSTAINED_MAX];
+	unsigned short			fn_state;
+	unsigned short			last_key[24];
+	spinlock_t			rawmidi_in_lock;
+	struct snd_card			*card;
+	struct snd_rawmidi		*rwmidi;
+	struct snd_rawmidi_substream	*in_substream;
+	struct snd_rawmidi_substream	*out_substream;
+	unsigned long			in_triggered;
+	unsigned long			out_active;
+};
+
+#define PK_QUIRK_NOGET	0x00010000
+#define PCMIDI_MIDDLE_C 60
+#define PCMIDI_CHANNEL_MIN 0
+#define PCMIDI_CHANNEL_MAX 15
+#define PCMIDI_OCTAVE_MIN (-2)
+#define PCMIDI_OCTAVE_MAX 2
+#define PCMIDI_SUSTAIN_MIN 0
+#define PCMIDI_SUSTAIN_MAX 5000
+
+static const char shortname[] = "PC-MIDI";
+static const char longname[] = "Prodikeys PC-MIDI Keyboard";
+
+static int index[SNDRV_CARDS] = SNDRV_DEFAULT_IDX;
+static char *id[SNDRV_CARDS] = SNDRV_DEFAULT_STR;
+static int enable[SNDRV_CARDS] = SNDRV_DEFAULT_ENABLE_PNP;
+
+module_param_array(index, int, NULL, 0444);
+module_param_array(id, charp, NULL, 0444);
+module_param_array(enable, bool, NULL, 0444);
+MODULE_PARM_DESC(index, "Index value for the PC-MIDI virtual audio driver");
+MODULE_PARM_DESC(id, "ID string for the PC-MIDI virtual audio driver");
+MODULE_PARM_DESC(enable, "Enable for the PC-MIDI virtual audio driver");
+
+
+/* Output routine for the sysfs channel file */
+static ssize_t show_channel(struct device *dev,
+	struct device_attribute *attr, char *buf)
+{
+	struct hid_device *hdev = container_of(dev, struct hid_device, dev);
+	struct pk_device *pk = (struct pk_device *)hid_get_drvdata(hdev);
+
+	dbg_hid("pcmidi sysfs read channel=%u\n", pk->pm->midi_channel);
+
+	return sprintf(buf, "%u (min:%u, max:%u)\n", pk->pm->midi_channel,
+		PCMIDI_CHANNEL_MIN, PCMIDI_CHANNEL_MAX);
+}
+
+/* Input routine for the sysfs channel file */
+static ssize_t store_channel(struct device *dev,
+	struct device_attribute *attr, const char *buf, size_t count)
+{
+	struct hid_device *hdev = container_of(dev, struct hid_device, dev);
+	struct pk_device *pk = (struct pk_device *)hid_get_drvdata(hdev);
+
+	unsigned channel = 0;
+
+	if (sscanf(buf, "%u", &channel) > 0 && channel <= PCMIDI_CHANNEL_MAX) {
+		dbg_hid("pcmidi sysfs write channel=%u\n", channel);
+		pk->pm->midi_channel = channel;
+		return strlen(buf);
+	}
+	return -EINVAL;
+}
+
+static DEVICE_ATTR(channel, S_IRUGO | S_IWUGO, show_channel,
+		store_channel);
+
+static struct device_attribute *sysfs_device_attr_channel = {
+		&dev_attr_channel,
+		};
+
+/* Output routine for the sysfs sustain file */
+static ssize_t show_sustain(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+	struct hid_device *hdev = container_of(dev, struct hid_device, dev);
+	struct pk_device *pk = (struct pk_device *)hid_get_drvdata(hdev);
+
+	dbg_hid("pcmidi sysfs read sustain=%u\n", pk->pm->midi_sustain);
+
+	return sprintf(buf, "%u (off:%u, max:%u (ms))\n", pk->pm->midi_sustain,
+		PCMIDI_SUSTAIN_MIN, PCMIDI_SUSTAIN_MAX);
+}
+
+/* Input routine for the sysfs sustain file */
+static ssize_t store_sustain(struct device *dev,
+	struct device_attribute *attr, const char *buf, size_t count)
+{
+	struct hid_device *hdev = container_of(dev, struct hid_device, dev);
+	struct pk_device *pk = (struct pk_device *)hid_get_drvdata(hdev);
+
+	unsigned sustain = 0;
+
+	if (sscanf(buf, "%u", &sustain) > 0 && sustain <= PCMIDI_SUSTAIN_MAX) {
+		dbg_hid("pcmidi sysfs write sustain=%u\n", sustain);
+		pk->pm->midi_sustain = sustain;
+		pk->pm->midi_sustain_mode =
+			(0 == sustain || !pk->pm->midi_mode) ? 0 : 1;
+		return strlen(buf);
+	}
+	return -EINVAL;
+}
+
+static DEVICE_ATTR(sustain, S_IRUGO | S_IWUGO, show_sustain,
+		store_sustain);
+
+static struct device_attribute *sysfs_device_attr_sustain = {
+		&dev_attr_sustain,
+		};
+
+/* Output routine for the sysfs octave file */
+static ssize_t show_octave(struct device *dev,
+	struct device_attribute *attr, char *buf)
+{
+	struct hid_device *hdev = container_of(dev, struct hid_device, dev);
+	struct pk_device *pk = (struct pk_device *)hid_get_drvdata(hdev);
+
+	dbg_hid("pcmidi sysfs read octave=%d\n", pk->pm->midi_octave);
+
+	return sprintf(buf, "%d (min:%d, max:%d)\n", pk->pm->midi_octave,
+		PCMIDI_OCTAVE_MIN, PCMIDI_OCTAVE_MAX);
+}
+
+/* Input routine for the sysfs octave file */
+static ssize_t store_octave(struct device *dev,
+	struct device_attribute *attr, const char *buf, size_t count)
+{
+	struct hid_device *hdev = container_of(dev, struct hid_device, dev);
+	struct pk_device *pk = (struct pk_device *)hid_get_drvdata(hdev);
+
+	int octave = 0;
+
+	if (sscanf(buf, "%d", &octave) > 0 &&
+		octave >= PCMIDI_OCTAVE_MIN && octave <= PCMIDI_OCTAVE_MAX) {
+		dbg_hid("pcmidi sysfs write octave=%d\n", octave);
+		pk->pm->midi_octave = octave;
+		return strlen(buf);
+	}
+	return -EINVAL;
+}
+
+static DEVICE_ATTR(octave, S_IRUGO | S_IWUGO, show_octave,
+		store_octave);
+
+static struct device_attribute *sysfs_device_attr_octave = {
+		&dev_attr_octave,
+		};
+
+
+static void pcmidi_send_note(struct pcmidi_snd *pm,
+	unsigned char status, unsigned char note, unsigned char velocity)
+{
+	unsigned long flags;
+	unsigned char buffer[3];
+
+	buffer[0] = status;
+	buffer[1] = note;
+	buffer[2] = velocity;
+
+	spin_lock_irqsave(&pm->rawmidi_in_lock, flags);
+
+	if (!pm->in_substream)
+		goto drop_note;
+	if (!test_bit(pm->in_substream->number, &pm->in_triggered))
+		goto drop_note;
+
+	snd_rawmidi_receive(pm->in_substream, buffer, 3);
+
+drop_note:
+	spin_unlock_irqrestore(&pm->rawmidi_in_lock, flags);
+
+	return;
+}
+
+void pcmidi_sustained_note_release(unsigned long data)
+{
+	struct pcmidi_sustain *pms = (struct pcmidi_sustain *)data;
+
+	pcmidi_send_note(pms->pm, pms->status, pms->note, pms->velocity);
+	pms->in_use = 0;
+}
+
+void init_sustain_timers(struct pcmidi_snd *pm)
+{
+	struct pcmidi_sustain *pms;
+	unsigned i;
+
+	for (i = 0; i < PCMIDI_SUSTAINED_MAX; i++) {
+		pms = &pm->sustained_notes[i];
+		pms->in_use = 0;
+		pms->pm = pm;
+		setup_timer(&pms->timer, pcmidi_sustained_note_release,
+			(unsigned long)pms);
+	}
+}
+
+void stop_sustain_timers(struct pcmidi_snd *pm)
+{
+	struct pcmidi_sustain *pms;
+	unsigned i;
+
+	for (i = 0; i < PCMIDI_SUSTAINED_MAX; i++) {
+		pms = &pm->sustained_notes[i];
+		pms->in_use = 1;
+		del_timer_sync(&pms->timer);
+	}
+}
+
+static int pcmidi_get_output_report(struct pcmidi_snd *pm)
+{
+	struct hid_device *hdev = pm->pk->hdev;
+	struct hid_report *report;
+
+	list_for_each_entry(report,
+		&hdev->report_enum[HID_OUTPUT_REPORT].report_list, list) {
+		if (!(6 == report->id))
+			continue;
+
+		if (report->maxfield < 1) {
+			dev_err(&hdev->dev, "output report is empty\n");
+			break;
+		}
+		if (report->field[0]->report_count != 2) {
+			dev_err(&hdev->dev, "field count too low\n");
+			break;
+		}
+		pm->pcmidi_report6 = report;
+		return 0;
+	}
+	/* should never get here */
+	return -ENODEV;
+}
+
+static void pcmidi_submit_output_report(struct pcmidi_snd *pm, int state)
+{
+	struct hid_device *hdev = pm->pk->hdev;
+	struct hid_report *report = pm->pcmidi_report6;
+	report->field[0]->value[0] = 0x01;
+	report->field[0]->value[1] = state;
+
+	usbhid_submit_report(hdev, report, USB_DIR_OUT);
+}
+
+static int pcmidi_handle_report1(struct pcmidi_snd *pm, u8 *data)
+{
+	u32 bit_mask;
+
+	bit_mask = data[1];
+	bit_mask = (bit_mask << 8) | data[2];
+	bit_mask = (bit_mask << 8) | data[3];
+
+	dbg_hid("pcmidi mode: %d\n", pm->midi_mode);
+
+	/*KEY_MAIL or octave down*/
+	if (pm->midi_mode && bit_mask == 0x004000) {
+		/* octave down */
+		pm->midi_octave--;
+		if (pm->midi_octave < -2)
+			pm->midi_octave = -2;
+		dbg_hid("pcmidi mode: %d octave: %d\n",
+			pm->midi_mode, pm->midi_octave);
+		return 1;
+	}
+	/*KEY_WWW or sustain*/
+	else if (pm->midi_mode && bit_mask == 0x000004) {
+		/* sustain on/off*/
+		pm->midi_sustain_mode ^= 0x1;
+		return 1;
+	}
+
+	return 0; /* continue key processing */
+}
+
+static int pcmidi_handle_report3(struct pcmidi_snd *pm, u8 *data, int size)
+{
+	struct pcmidi_sustain *pms;
+	unsigned i, j;
+	unsigned char status, note, velocity;
+
+	unsigned num_notes = (size-1)/2;
+	for (j = 0; j < num_notes; j++)	{
+		note = data[j*2+1];
+		velocity = data[j*2+2];
+
+		if (note < 0x81) { /* note on */
+			status = 128 + 16 + pm->midi_channel; /* 1001nnnn */
+			note = note - 0x54 + PCMIDI_MIDDLE_C +
+				(pm->midi_octave * 12);
+			if (0 == velocity)
+				velocity = 1; /* force note on */
+		} else { /* note off */
+			status = 128 + pm->midi_channel; /* 1000nnnn */
+			note = note - 0x94 + PCMIDI_MIDDLE_C +
+				(pm->midi_octave*12);
+
+			if (pm->midi_sustain_mode) {
+				for (i = 0; i < PCMIDI_SUSTAINED_MAX; i++) {
+					pms = &pm->sustained_notes[i];
+					if (!pms->in_use) {
+						pms->status = status;
+						pms->note = note;
+						pms->velocity = velocity;
+						pms->in_use = 1;
+
+						mod_timer(&pms->timer,
+							jiffies +
+					msecs_to_jiffies(pm->midi_sustain));
+						return 1;
+					}
+				}
+			}
+		}
+		pcmidi_send_note(pm, status, note, velocity);
+	}
+
+	return 1;
+}
+
+static int pcmidi_handle_report4(struct pcmidi_snd *pm, u8 *data)
+{
+	unsigned	key;
+	u32		bit_mask;
+	u32		bit_index;
+
+	bit_mask = data[1];
+	bit_mask = (bit_mask << 8) | data[2];
+	bit_mask = (bit_mask << 8) | data[3];
+
+	/* break keys */
+	for (bit_index = 0; bit_index < 24; bit_index++) {
+		key = pm->last_key[bit_index];
+		if (!((0x01 << bit_index) & bit_mask)) {
+			input_event(pm->input_ep82, EV_KEY,
+				pm->last_key[bit_index], 0);
+				pm->last_key[bit_index] = 0;
+		}
+	}
+
+	/* make keys */
+	for (bit_index = 0; bit_index < 24; bit_index++) {
+		key = 0;
+		switch ((0x01 << bit_index) & bit_mask) {
+		case 0x000010: /* Fn lock*/
+			pm->fn_state ^= 0x000010;
+			if (pm->fn_state)
+				pcmidi_submit_output_report(pm, 0xc5);
+			else
+				pcmidi_submit_output_report(pm, 0xc6);
+			continue;
+		case 0x020000: /* midi launcher..send a key (qwerty) or not? */
+			pcmidi_submit_output_report(pm, 0xc1);
+			pm->midi_mode ^= 0x01;
+
+			dbg_hid("pcmidi mode: %d\n", pm->midi_mode);
+			continue;
+		case 0x100000: /* KEY_MESSENGER or octave up */
+			dbg_hid("pcmidi mode: %d\n", pm->midi_mode);
+			if (pm->midi_mode) {
+				pm->midi_octave++;
+				if (pm->midi_octave > 2)
+					pm->midi_octave = 2;
+				dbg_hid("pcmidi mode: %d octave: %d\n",
+					pm->midi_mode, pm->midi_octave);
+			    continue;
+			} else
+				key = KEY_MESSENGER;
+			break;
+		case 0x400000:
+			key = KEY_CALENDAR;
+			break;
+		case 0x080000:
+			key = KEY_ADDRESSBOOK;
+			break;
+		case 0x040000:
+			key = KEY_DOCUMENTS;
+			break;
+		case 0x800000:
+			key = KEY_WORDPROCESSOR;
+			break;
+		case 0x200000:
+			key = KEY_SPREADSHEET;
+			break;
+		case 0x010000:
+			key = KEY_COFFEE;
+			break;
+		case 0x000100:
+			key = KEY_HELP;
+			break;
+		case 0x000200:
+			key = KEY_SEND;
+			break;
+		case 0x000400:
+			key = KEY_REPLY;
+			break;
+		case 0x000800:
+			key = KEY_FORWARDMAIL;
+			break;
+		case 0x001000:
+			key = KEY_NEW;
+			break;
+		case 0x002000:
+			key = KEY_OPEN;
+			break;
+		case 0x004000:
+			key = KEY_CLOSE;
+			break;
+		case 0x008000:
+			key = KEY_SAVE;
+			break;
+		case 0x000001:
+			key = KEY_UNDO;
+			break;
+		case 0x000002:
+			key = KEY_REDO;
+			break;
+		case 0x000004:
+			key = KEY_SPELLCHECK;
+			break;
+		case 0x000008:
+			key = KEY_PRINT;
+			break;
+		}
+		if (key) {
+			input_event(pm->input_ep82, EV_KEY, key, 1);
+			pm->last_key[bit_index] = key;
+		}
+	}
+
+	return 1;
+}
+
+int pcmidi_handle_report(
+	struct pcmidi_snd *pm, unsigned report_id, u8 *data, int size)
+{
+	int ret = 0;
+
+	switch (report_id) {
+	case 0x01: /* midi keys (qwerty)*/
+		ret = pcmidi_handle_report1(pm, data);
+		break;
+	case 0x03: /* midi keyboard (musical)*/
+		ret = pcmidi_handle_report3(pm, data, size);
+		break;
+	case 0x04: /* multimedia/midi keys (qwerty)*/
+		ret = pcmidi_handle_report4(pm, data);
+		break;
+	}
+	return ret;
+}
+
+void pcmidi_setup_extra_keys(struct pcmidi_snd *pm, struct input_dev *input)
+{
+	/* reassigned functionality for N/A keys
+		MY PICTURES =>	KEY_WORDPROCESSOR
+		MY MUSIC=>	KEY_SPREADSHEET
+	*/
+	unsigned int keys[] = {
+		KEY_FN,
+		KEY_MESSENGER, KEY_CALENDAR,
+		KEY_ADDRESSBOOK, KEY_DOCUMENTS,
+		KEY_WORDPROCESSOR,
+		KEY_SPREADSHEET,
+		KEY_COFFEE,
+		KEY_HELP, KEY_SEND,
+		KEY_REPLY, KEY_FORWARDMAIL,
+		KEY_NEW, KEY_OPEN,
+		KEY_CLOSE, KEY_SAVE,
+		KEY_UNDO, KEY_REDO,
+		KEY_SPELLCHECK,	KEY_PRINT,
+		0
+	};
+
+	unsigned int *pkeys = &keys[0];
+	unsigned short i;
+
+	if (pm->ifnum != 1)  /* only set up ONCE for interace 1 */
+		return;
+
+	pm->input_ep82 = input;
+
+	for (i = 0; i < 24; i++)
+		pm->last_key[i] = 0;
+
+	while (*pkeys != 0) {
+		set_bit(*pkeys, pm->input_ep82->keybit);
+		++pkeys;
+	}
+}
+
+static int pcmidi_set_operational(struct pcmidi_snd *pm)
+{
+	if (pm->ifnum != 1)
+		return 0; /* only set up ONCE for interace 1 */
+
+	pcmidi_get_output_report(pm);
+	pcmidi_submit_output_report(pm, 0xc1);
+	return 0;
+}
+
+static int pcmidi_snd_free(struct snd_device *dev)
+{
+	return 0;
+}
+
+static int pcmidi_in_open(struct snd_rawmidi_substream *substream)
+{
+	struct pcmidi_snd *pm = substream->rmidi->private_data;
+
+	dbg_hid("pcmidi in open\n");
+	pm->in_substream = substream;
+	return 0;
+}
+
+static int pcmidi_in_close(struct snd_rawmidi_substream *substream)
+{
+	dbg_hid("pcmidi in close\n");
+	return 0;
+}
+
+static void pcmidi_in_trigger(struct snd_rawmidi_substream *substream, int up)
+{
+	struct pcmidi_snd *pm = substream->rmidi->private_data;
+
+	dbg_hid("pcmidi in trigger %d\n", up);
+
+	pm->in_triggered = up;
+}
+
+static struct snd_rawmidi_ops pcmidi_in_ops = {
+	.open = pcmidi_in_open,
+	.close = pcmidi_in_close,
+	.trigger = pcmidi_in_trigger
+};
+
+int pcmidi_snd_initialise(struct pcmidi_snd *pm)
+{
+	static int dev;
+	struct snd_card *card;
+	struct snd_rawmidi *rwmidi;
+	int err;
+
+	static struct snd_device_ops ops = {
+		.dev_free = pcmidi_snd_free,
+	};
+
+	if (pm->ifnum != 1)
+		return 0; /* only set up midi device ONCE for interace 1 */
+
+	if (dev >= SNDRV_CARDS)
+		return -ENODEV;
+
+	if (!enable[dev]) {
+		dev++;
+		return -ENOENT;
+	}
+
+	/* Setup sound card */
+
+	err = snd_card_create(index[dev], id[dev], THIS_MODULE, 0, &card);
+	if (err < 0) {
+		pk_error("failed to create pc-midi sound card\n");
+		err = -ENOMEM;
+		goto fail;
+	}
+	pm->card = card;
+
+	/* Setup sound device */
+	err = snd_device_new(card, SNDRV_DEV_LOWLEVEL, pm, &ops);
+	if (err < 0) {
+		pk_error("failed to create pc-midi sound device: error %d\n",
+			err);
+		goto fail;
+	}
+
+	strncpy(card->driver, shortname, sizeof(card->driver));
+	strncpy(card->shortname, shortname, sizeof(card->shortname));
+	strncpy(card->longname, longname, sizeof(card->longname));
+
+	/* Set up rawmidi */
+	err = snd_rawmidi_new(card, card->shortname, 0,
+			      0, 1, &rwmidi);
+	if (err < 0) {
+		pk_error("failed to create pc-midi rawmidi device: error %d\n",
+			err);
+		goto fail;
+	}
+	pm->rwmidi = rwmidi;
+	strncpy(rwmidi->name, card->shortname, sizeof(rwmidi->name));
+	rwmidi->info_flags = SNDRV_RAWMIDI_INFO_INPUT;
+	rwmidi->private_data = pm;
+
+	snd_rawmidi_set_ops(rwmidi, SNDRV_RAWMIDI_STREAM_INPUT,
+		&pcmidi_in_ops);
+
+	snd_card_set_dev(card, &pm->pk->hdev->dev);
+
+	/* create sysfs variables */
+	err = device_create_file(&pm->pk->hdev->dev,
+				 sysfs_device_attr_channel);
+	if (err < 0) {
+		pk_error("failed to create sysfs attribute channel: error %d\n",
+			err);
+		goto fail;
+	}
+
+	err = device_create_file(&pm->pk->hdev->dev,
+				sysfs_device_attr_sustain);
+	if (err < 0) {
+		pk_error("failed to create sysfs attribute sustain: error %d\n",
+			err);
+		goto fail_attr_sustain;
+	}
+
+	err = device_create_file(&pm->pk->hdev->dev,
+			 sysfs_device_attr_octave);
+	if (err < 0) {
+		pk_error("failed to create sysfs attribute octave: error %d\n",
+			err);
+		goto fail_attr_octave;
+	}
+
+	spin_lock_init(&pm->rawmidi_in_lock);
+
+	init_sustain_timers(pm);
+	pcmidi_set_operational(pm);
+
+	/* register it */
+	err = snd_card_register(card);
+	if (err < 0) {
+		pk_error("failed to register pc-midi sound card: error %d\n",
+			 err);
+			 goto fail_register;
+	}
+
+	dbg_hid("pcmidi_snd_initialise finished ok\n");
+	return 0;
+
+fail_register:
+	stop_sustain_timers(pm);
+	device_remove_file(&pm->pk->hdev->dev, sysfs_device_attr_octave);
+fail_attr_octave:
+	device_remove_file(&pm->pk->hdev->dev, sysfs_device_attr_sustain);
+fail_attr_sustain:
+	device_remove_file(&pm->pk->hdev->dev, sysfs_device_attr_channel);
+fail:
+	if (pm->card) {
+		snd_card_free(pm->card);
+		pm->card = NULL;
+	}
+	return err;
+}
+
+int pcmidi_snd_terminate(struct pcmidi_snd *pm)
+{
+	if (pm->card) {
+		stop_sustain_timers(pm);
+
+		device_remove_file(&pm->pk->hdev->dev,
+			sysfs_device_attr_channel);
+		device_remove_file(&pm->pk->hdev->dev,
+			sysfs_device_attr_sustain);
+		device_remove_file(&pm->pk->hdev->dev,
+			sysfs_device_attr_octave);
+
+		snd_card_disconnect(pm->card);
+		snd_card_free_when_closed(pm->card);
+	}
+
+	return 0;
+}
+
+/*
+ * PC-MIDI report descriptor for report id is wrong.
+ */
+static void pk_report_fixup(struct hid_device *hdev, __u8 *rdesc,
+		unsigned int rsize)
+{
+	if (rsize == 178 &&
+	      rdesc[111] == 0x06 && rdesc[112] == 0x00 &&
+	      rdesc[113] == 0xff) {
+		dev_info(&hdev->dev, "fixing up pc-midi keyboard report "
+			"descriptor\n");
+
+		rdesc[144] = 0x18; /* report 4: was 0x10 report count */
+	}
+}
+
+static int pk_input_mapping(struct hid_device *hdev, struct hid_input *hi,
+		struct hid_field *field, struct hid_usage *usage,
+		unsigned long **bit, int *max)
+{
+	struct pk_device *pk = (struct pk_device *)hid_get_drvdata(hdev);
+	struct pcmidi_snd *pm;
+
+	pm = pk->pm;
+
+	if (HID_UP_MSVENDOR == (usage->hid & HID_USAGE_PAGE) &&
+		1 == pm->ifnum) {
+		pcmidi_setup_extra_keys(pm, hi->input);
+		return 0;
+	}
+
+	return 0;
+}
+
+
+static int pk_raw_event(struct hid_device *hdev, struct hid_report *report,
+	u8 *data, int size)
+{
+	struct pk_device *pk = (struct pk_device *)hid_get_drvdata(hdev);
+	int ret = 0;
+
+	if (1 == pk->pm->ifnum) {
+		if (report->id == data[0])
+			switch (report->id) {
+			case 0x01: /* midi keys (qwerty)*/
+			case 0x03: /* midi keyboard (musical)*/
+			case 0x04: /* extra/midi keys (qwerty)*/
+				ret = pcmidi_handle_report(pk->pm,
+						report->id, data, size);
+				break;
+			}
+	}
+
+	return ret;
+}
+
+static int pk_probe(struct hid_device *hdev, const struct hid_device_id *id)
+{
+	int ret;
+	struct usb_interface *intf = to_usb_interface(hdev->dev.parent);
+	unsigned short ifnum = intf->cur_altsetting->desc.bInterfaceNumber;
+	unsigned long quirks = id->driver_data;
+	struct pk_device *pk;
+	struct pcmidi_snd *pm = NULL;
+
+	pk = kzalloc(sizeof(*pk), GFP_KERNEL);
+	if (pk == NULL) {
+		dev_err(&hdev->dev, "prodikeys: can't alloc descriptor\n");
+		return -ENOMEM;
+	}
+
+	pk->hdev = hdev;
+
+	pm = kzalloc(sizeof(*pm), GFP_KERNEL);
+	if (pm == NULL) {
+		dev_err(&hdev->dev,
+			"prodikeys: can't alloc descriptor\n");
+		ret = -ENOMEM;
+		goto err_free;
+	}
+
+	pm->pk = pk;
+	pk->pm = pm;
+	pm->ifnum = ifnum;
+
+	hid_set_drvdata(hdev, pk);
+
+	ret = hid_parse(hdev);
+	if (ret) {
+		dev_err(&hdev->dev, "prodikeys: hid parse failed\n");
+		goto err_free;
+	}
+
+	if (quirks & PK_QUIRK_NOGET) { /* hid_parse cleared all the quirks */
+		hdev->quirks |= HID_QUIRK_NOGET;
+	}
+
+	ret = hid_hw_start(hdev, HID_CONNECT_DEFAULT);
+	if (ret) {
+		dev_err(&hdev->dev, "prodikeys: hw start failed\n");
+		goto err_free;
+	}
+
+	ret = pcmidi_snd_initialise(pm);
+	if (ret < 0)
+		goto err_stop;
+
+	return 0;
+err_stop:
+	hid_hw_stop(hdev);
+err_free:
+	if (pm != NULL)
+		kfree(pm);
+
+	kfree(pk);
+	return ret;
+}
+
+static void pk_remove(struct hid_device *hdev)
+{
+	struct pk_device *pk = (struct pk_device *)hid_get_drvdata(hdev);
+	struct pcmidi_snd *pm;
+
+	pm = pk->pm;
+	if (pm) {
+		pcmidi_snd_terminate(pm);
+		kfree(pm);
+	}
+
+	hid_hw_stop(hdev);
+
+	kfree(pk);
+}
+
+static const struct hid_device_id pk_devices[] = {
+	{HID_USB_DEVICE(USB_VENDOR_ID_CREATIVELABS,
+		USB_DEVICE_ID_PRODIKEYS_PCMIDI),
+	    .driver_data = PK_QUIRK_NOGET},
+	{ }
+};
+MODULE_DEVICE_TABLE(hid, pk_devices);
+
+static struct hid_driver pk_driver = {
+	.name = "prodikeys",
+	.id_table = pk_devices,
+	.report_fixup = pk_report_fixup,
+	.input_mapping = pk_input_mapping,
+	.raw_event = pk_raw_event,
+	.probe = pk_probe,
+	.remove = pk_remove,
+};
+
+static int pk_init(void)
+{
+	int ret;
+
+	ret = hid_register_driver(&pk_driver);
+	if (ret)
+		printk(KERN_ERR "can't register prodikeys driver\n");
+
+	return ret;
+}
+
+static void pk_exit(void)
+{
+	hid_unregister_driver(&pk_driver);
+}
+
+module_init(pk_init);
+module_exit(pk_exit);
+MODULE_LICENSE("GPL");
diff --git a/drivers/hid/hid-roccat-kone.c b/drivers/hid/hid-roccat-kone.c
new file mode 100644
index 0000000..66e6940
--- /dev/null
+++ b/drivers/hid/hid-roccat-kone.c
@@ -0,0 +1,994 @@
+/*
+ * Roccat Kone driver for Linux
+ *
+ * Copyright (c) 2010 Stefan Achatz <erazor_de@users.sourceforge.net>
+ */
+
+/*
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ */
+
+/*
+ * Roccat Kone is a gamer mouse which consists of a mouse part and a keyboard
+ * part. The keyboard part enables the mouse to execute stored macros with mixed
+ * key- and button-events.
+ *
+ * TODO implement on-the-fly polling-rate change
+ *      The windows driver has the ability to change the polling rate of the
+ *      device on the press of a mousebutton.
+ *      Is it possible to remove and reinstall the urb in raw-event- or any
+ *      other handler, or to defer this action to be executed somewhere else?
+ *
+ * TODO implement notification mechanism for overlong macro execution
+ *      If user wants to execute an overlong macro only the names of macroset
+ *      and macro are given. Should userland tap hidraw or is there an
+ *      additional streaming mechanism?
+ *
+ * TODO is it possible to overwrite group for sysfs attributes via udev?
+ */
+
+#include <linux/device.h>
+#include <linux/input.h>
+#include <linux/hid.h>
+#include <linux/usb.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include "hid-ids.h"
+#include "hid-roccat-kone.h"
+
+static void kone_set_settings_checksum(struct kone_settings *settings)
+{
+	uint16_t checksum = 0;
+	unsigned char *address = (unsigned char *)settings;
+	int i;
+
+	for (i = 0; i < sizeof(struct kone_settings) - 2; ++i, ++address)
+		checksum += *address;
+	settings->checksum = cpu_to_le16(checksum);
+}
+
+/*
+ * Checks success after writing data to mouse
+ * On success returns 0
+ * On failure returns errno
+ */
+static int kone_check_write(struct usb_device *usb_dev)
+{
+	int len;
+	unsigned char *data;
+
+	data = kmalloc(1, GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	do {
+		/*
+		 * Mouse needs 50 msecs until it says ok, but there are
+		 * 30 more msecs needed for next write to work.
+		 */
+		msleep(80);
+
+		len = usb_control_msg(usb_dev, usb_rcvctrlpipe(usb_dev, 0),
+				USB_REQ_CLEAR_FEATURE,
+				USB_TYPE_CLASS | USB_RECIP_INTERFACE |
+				USB_DIR_IN,
+				kone_command_confirm_write, 0, data, 1,
+				USB_CTRL_SET_TIMEOUT);
+
+		if (len != 1) {
+			kfree(data);
+			return -EIO;
+		}
+
+		/*
+		 * value of 3 seems to mean something like
+		 * "not finished yet, but it looks good"
+		 * So check again after a moment.
+		 */
+	} while (*data == 3);
+
+	if (*data == 1) { /* everything alright */
+		kfree(data);
+		return 0;
+	} else { /* unknown answer */
+		dev_err(&usb_dev->dev, "got retval %d when checking write\n",
+				*data);
+		kfree(data);
+		return -EIO;
+	}
+}
+
+/*
+ * Reads settings from mouse and stores it in @buf
+ * @buf has to be alloced with GFP_KERNEL
+ * On success returns 0
+ * On failure returns errno
+ */
+static int kone_get_settings(struct usb_device *usb_dev,
+		struct kone_settings *buf)
+{
+	int len;
+
+	len = usb_control_msg(usb_dev, usb_rcvctrlpipe(usb_dev, 0),
+			USB_REQ_CLEAR_FEATURE,
+			USB_TYPE_CLASS | USB_RECIP_INTERFACE | USB_DIR_IN,
+			kone_command_settings, 0, buf,
+			sizeof(struct kone_settings), USB_CTRL_SET_TIMEOUT);
+
+	if (len != sizeof(struct kone_settings))
+		return -EIO;
+
+	return 0;
+}
+
+/*
+ * Writes settings from @buf to mouse
+ * On success returns 0
+ * On failure returns errno
+ */
+static int kone_set_settings(struct usb_device *usb_dev,
+		struct kone_settings const *settings)
+{
+	int len;
+
+	len = usb_control_msg(usb_dev, usb_sndctrlpipe(usb_dev, 0),
+			USB_REQ_SET_CONFIGURATION,
+			USB_TYPE_CLASS | USB_RECIP_INTERFACE | USB_DIR_OUT,
+			kone_command_settings, 0, (char *)settings,
+			sizeof(struct kone_settings),
+			USB_CTRL_SET_TIMEOUT);
+
+	if (len != sizeof(struct kone_settings))
+		return -EIO;
+
+	if (kone_check_write(usb_dev))
+		return -EIO;
+
+	return 0;
+}
+
+/*
+ * Reads profile data from mouse and stores it in @buf
+ * @number: profile number to read
+ * On success returns 0
+ * On failure returns errno
+ */
+static int kone_get_profile(struct usb_device *usb_dev,
+		struct kone_profile *buf, int number)
+{
+	int len;
+
+	if (number < 1 || number > 5)
+		return -EINVAL;
+
+	len = usb_control_msg(usb_dev, usb_rcvctrlpipe(usb_dev, 0),
+			USB_REQ_CLEAR_FEATURE,
+			USB_TYPE_CLASS | USB_RECIP_INTERFACE | USB_DIR_IN,
+			kone_command_profile, number, buf,
+			sizeof(struct kone_profile), USB_CTRL_SET_TIMEOUT);
+
+	if (len != sizeof(struct kone_profile))
+		return -EIO;
+
+	return 0;
+}
+
+/*
+ * Writes profile data to mouse.
+ * @number: profile number to write
+ * On success returns 0
+ * On failure returns errno
+ */
+static int kone_set_profile(struct usb_device *usb_dev,
+		struct kone_profile const *profile, int number)
+{
+	int len;
+
+	if (number < 1 || number > 5)
+		return -EINVAL;
+
+	len = usb_control_msg(usb_dev, usb_sndctrlpipe(usb_dev, 0),
+			USB_REQ_SET_CONFIGURATION,
+			USB_TYPE_CLASS | USB_RECIP_INTERFACE | USB_DIR_OUT,
+			kone_command_profile, number, (char *)profile,
+			sizeof(struct kone_profile),
+			USB_CTRL_SET_TIMEOUT);
+
+	if (len != sizeof(struct kone_profile))
+		return len;
+
+	if (kone_check_write(usb_dev))
+		return -EIO;
+
+	return 0;
+}
+
+/*
+ * Reads value of "fast-clip-weight" and stores it in @result
+ * On success returns 0
+ * On failure returns errno
+ */
+static int kone_get_weight(struct usb_device *usb_dev, int *result)
+{
+	int len;
+	uint8_t *data;
+
+	data = kmalloc(1, GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	len = usb_control_msg(usb_dev, usb_rcvctrlpipe(usb_dev, 0),
+			USB_REQ_CLEAR_FEATURE,
+			USB_TYPE_CLASS | USB_RECIP_INTERFACE | USB_DIR_IN,
+			kone_command_weight, 0, data, 1, USB_CTRL_SET_TIMEOUT);
+
+	if (len != 1) {
+		kfree(data);
+		return -EIO;
+	}
+	*result = (int)*data;
+	kfree(data);
+	return 0;
+}
+
+/*
+ * Reads firmware_version of mouse and stores it in @result
+ * On success returns 0
+ * On failure returns errno
+ */
+static int kone_get_firmware_version(struct usb_device *usb_dev, int *result)
+{
+	int len;
+	unsigned char *data;
+
+	data = kmalloc(2, GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	len = usb_control_msg(usb_dev, usb_rcvctrlpipe(usb_dev, 0),
+			USB_REQ_CLEAR_FEATURE,
+			USB_TYPE_CLASS | USB_RECIP_INTERFACE | USB_DIR_IN,
+			kone_command_firmware_version, 0, data, 2,
+			USB_CTRL_SET_TIMEOUT);
+
+	if (len != 2) {
+		kfree(data);
+		return -EIO;
+	}
+	*result = le16_to_cpu(*data);
+	kfree(data);
+	return 0;
+}
+
+static ssize_t kone_sysfs_read_settings(struct kobject *kobj,
+		struct bin_attribute *attr, char *buf,
+		loff_t off, size_t count) {
+	struct device *dev = container_of(kobj, struct device, kobj);
+	struct kone_device *kone = hid_get_drvdata(dev_get_drvdata(dev));
+
+	if (off >= sizeof(struct kone_settings))
+		return 0;
+
+	if (off + count > sizeof(struct kone_settings))
+		count = sizeof(struct kone_settings) - off;
+
+	mutex_lock(&kone->kone_lock);
+	memcpy(buf, &kone->settings + off, count);
+	mutex_unlock(&kone->kone_lock);
+
+	return count;
+}
+
+/*
+ * Writing settings automatically activates startup_profile.
+ * This function keeps values in kone_device up to date and assumes that in
+ * case of error the old data is still valid
+ */
+static ssize_t kone_sysfs_write_settings(struct kobject *kobj,
+		struct bin_attribute *attr, char *buf,
+		loff_t off, size_t count) {
+	struct device *dev = container_of(kobj, struct device, kobj);
+	struct kone_device *kone = hid_get_drvdata(dev_get_drvdata(dev));
+	struct usb_device *usb_dev = interface_to_usbdev(to_usb_interface(dev));
+	int retval = 0, difference;
+
+	/* I need to get my data in one piece */
+	if (off != 0 || count != sizeof(struct kone_settings))
+		return -EINVAL;
+
+	mutex_lock(&kone->kone_lock);
+	difference = memcmp(buf, &kone->settings, sizeof(struct kone_settings));
+	if (difference) {
+		retval = kone_set_settings(usb_dev,
+				(struct kone_settings const *)buf);
+		if (!retval)
+			memcpy(&kone->settings, buf,
+					sizeof(struct kone_settings));
+	}
+	mutex_unlock(&kone->kone_lock);
+
+	if (retval)
+		return retval;
+
+	/*
+	 * If we get here, treat settings as okay and update actual values
+	 * according to startup_profile
+	 */
+	kone->actual_profile = kone->settings.startup_profile;
+	kone->actual_dpi = kone->profiles[kone->actual_profile - 1].startup_dpi;
+
+	return sizeof(struct kone_settings);
+}
+
+static ssize_t kone_sysfs_read_profilex(struct kobject *kobj,
+		struct bin_attribute *attr, char *buf,
+		loff_t off, size_t count, int number) {
+	struct device *dev = container_of(kobj, struct device, kobj);
+	struct kone_device *kone = hid_get_drvdata(dev_get_drvdata(dev));
+
+	if (off >= sizeof(struct kone_profile))
+		return 0;
+
+	if (off + count > sizeof(struct kone_profile))
+		count = sizeof(struct kone_profile) - off;
+
+	mutex_lock(&kone->kone_lock);
+	memcpy(buf, &kone->profiles[number - 1], sizeof(struct kone_profile));
+	mutex_unlock(&kone->kone_lock);
+
+	return count;
+}
+
+static ssize_t kone_sysfs_read_profile1(struct kobject *kobj,
+		struct bin_attribute *attr, char *buf,
+		loff_t off, size_t count) {
+	return kone_sysfs_read_profilex(kobj, attr, buf, off, count, 1);
+}
+
+static ssize_t kone_sysfs_read_profile2(struct kobject *kobj,
+		struct bin_attribute *attr, char *buf,
+		loff_t off, size_t count) {
+	return kone_sysfs_read_profilex(kobj, attr, buf, off, count, 2);
+}
+
+static ssize_t kone_sysfs_read_profile3(struct kobject *kobj,
+		struct bin_attribute *attr, char *buf,
+		loff_t off, size_t count) {
+	return kone_sysfs_read_profilex(kobj, attr, buf, off, count, 3);
+}
+
+static ssize_t kone_sysfs_read_profile4(struct kobject *kobj,
+		struct bin_attribute *attr, char *buf,
+		loff_t off, size_t count) {
+	return kone_sysfs_read_profilex(kobj, attr, buf, off, count, 4);
+}
+
+static ssize_t kone_sysfs_read_profile5(struct kobject *kobj,
+		struct bin_attribute *attr, char *buf,
+		loff_t off, size_t count) {
+	return kone_sysfs_read_profilex(kobj, attr, buf, off, count, 5);
+}
+
+/* Writes data only if different to stored data */
+static ssize_t kone_sysfs_write_profilex(struct kobject *kobj,
+		struct bin_attribute *attr, char *buf,
+		loff_t off, size_t count, int number) {
+	struct device *dev = container_of(kobj, struct device, kobj);
+	struct kone_device *kone = hid_get_drvdata(dev_get_drvdata(dev));
+	struct usb_device *usb_dev = interface_to_usbdev(to_usb_interface(dev));
+	struct kone_profile *profile;
+	int retval = 0, difference;
+
+	/* I need to get my data in one piece */
+	if (off != 0 || count != sizeof(struct kone_profile))
+		return -EINVAL;
+
+	profile = &kone->profiles[number - 1];
+
+	mutex_lock(&kone->kone_lock);
+	difference = memcmp(buf, profile, sizeof(struct kone_profile));
+	if (difference) {
+		retval = kone_set_profile(usb_dev,
+				(struct kone_profile const *)buf, number);
+		if (!retval)
+			memcpy(profile, buf, sizeof(struct kone_profile));
+	}
+	mutex_unlock(&kone->kone_lock);
+
+	if (retval)
+		return retval;
+
+	return sizeof(struct kone_profile);
+}
+
+static ssize_t kone_sysfs_write_profile1(struct kobject *kobj,
+		struct bin_attribute *attr, char *buf,
+		loff_t off, size_t count) {
+	return kone_sysfs_write_profilex(kobj, attr, buf, off, count, 1);
+}
+
+static ssize_t kone_sysfs_write_profile2(struct kobject *kobj,
+		struct bin_attribute *attr, char *buf,
+		loff_t off, size_t count) {
+	return kone_sysfs_write_profilex(kobj, attr, buf, off, count, 2);
+}
+
+static ssize_t kone_sysfs_write_profile3(struct kobject *kobj,
+		struct bin_attribute *attr, char *buf,
+		loff_t off, size_t count) {
+	return kone_sysfs_write_profilex(kobj, attr, buf, off, count, 3);
+}
+
+static ssize_t kone_sysfs_write_profile4(struct kobject *kobj,
+		struct bin_attribute *attr, char *buf,
+		loff_t off, size_t count) {
+	return kone_sysfs_write_profilex(kobj, attr, buf, off, count, 4);
+}
+
+static ssize_t kone_sysfs_write_profile5(struct kobject *kobj,
+		struct bin_attribute *attr, char *buf,
+		loff_t off, size_t count) {
+	return kone_sysfs_write_profilex(kobj, attr, buf, off, count, 5);
+}
+
+static ssize_t kone_sysfs_show_actual_profile(struct device *dev,
+		struct device_attribute *attr, char *buf)
+{
+	struct kone_device *kone = hid_get_drvdata(dev_get_drvdata(dev));
+	return snprintf(buf, PAGE_SIZE, "%d\n", kone->actual_profile);
+}
+
+static ssize_t kone_sysfs_show_actual_dpi(struct device *dev,
+		struct device_attribute *attr, char *buf)
+{
+	struct kone_device *kone = hid_get_drvdata(dev_get_drvdata(dev));
+	return snprintf(buf, PAGE_SIZE, "%d\n", kone->actual_dpi);
+}
+
+/* weight is read each time, since we don't get informed when it's changed */
+static ssize_t kone_sysfs_show_weight(struct device *dev,
+		struct device_attribute *attr, char *buf)
+{
+	struct kone_device *kone = hid_get_drvdata(dev_get_drvdata(dev));
+	struct usb_device *usb_dev = interface_to_usbdev(to_usb_interface(dev));
+	int weight = 0;
+	int retval;
+
+	mutex_lock(&kone->kone_lock);
+	retval = kone_get_weight(usb_dev, &weight);
+	mutex_unlock(&kone->kone_lock);
+
+	if (retval)
+		return retval;
+	return snprintf(buf, PAGE_SIZE, "%d\n", weight);
+}
+
+static ssize_t kone_sysfs_show_firmware_version(struct device *dev,
+		struct device_attribute *attr, char *buf)
+{
+	struct kone_device *kone = hid_get_drvdata(dev_get_drvdata(dev));
+	return snprintf(buf, PAGE_SIZE, "%d\n", kone->firmware_version);
+}
+
+static ssize_t kone_sysfs_show_tcu(struct device *dev,
+		struct device_attribute *attr, char *buf)
+{
+	struct kone_device *kone = hid_get_drvdata(dev_get_drvdata(dev));
+	return snprintf(buf, PAGE_SIZE, "%d\n", kone->settings.tcu);
+}
+
+static int kone_tcu_command(struct usb_device *usb_dev, int number)
+{
+	int len;
+	char *value;
+
+	value = kmalloc(1, GFP_KERNEL);
+	if (!value)
+		return -ENOMEM;
+
+	*value = number;
+
+	len = usb_control_msg(usb_dev, usb_sndctrlpipe(usb_dev, 0),
+			USB_REQ_SET_CONFIGURATION,
+			USB_TYPE_CLASS | USB_RECIP_INTERFACE | USB_DIR_OUT,
+			kone_command_calibrate, 0, value, 1,
+			USB_CTRL_SET_TIMEOUT);
+
+	kfree(value);
+	return ((len != 1) ? -EIO : 0);
+}
+
+/*
+ * Calibrating the tcu is the only action that changes settings data inside the
+ * mouse, so this data needs to be reread
+ */
+static ssize_t kone_sysfs_set_tcu(struct device *dev,
+		struct device_attribute *attr, char const *buf, size_t size)
+{
+	struct kone_device *kone = hid_get_drvdata(dev_get_drvdata(dev));
+	struct usb_device *usb_dev = interface_to_usbdev(to_usb_interface(dev));
+	int retval;
+	unsigned long state;
+
+	retval = strict_strtoul(buf, 10, &state);
+	if (retval)
+		return retval;
+
+	if (state != 0 && state != 1)
+		return -EINVAL;
+
+	mutex_lock(&kone->kone_lock);
+
+	if (state == 1) { /* state activate */
+		retval = kone_tcu_command(usb_dev, 1);
+		if (retval)
+			goto exit_unlock;
+		retval = kone_tcu_command(usb_dev, 2);
+		if (retval)
+			goto exit_unlock;
+		ssleep(5); /* tcu needs this time for calibration */
+		retval = kone_tcu_command(usb_dev, 3);
+		if (retval)
+			goto exit_unlock;
+		retval = kone_tcu_command(usb_dev, 0);
+		if (retval)
+			goto exit_unlock;
+		retval = kone_tcu_command(usb_dev, 4);
+		if (retval)
+			goto exit_unlock;
+		/*
+		 * Kone needs this time to settle things.
+		 * Reading settings too early will result in invalid data.
+		 * Roccat's driver waits 1 sec, maybe this time could be
+		 * shortened.
+		 */
+		ssleep(1);
+	}
+
+	/* calibration changes values in settings, so reread */
+	retval = kone_get_settings(usb_dev, &kone->settings);
+	if (retval)
+		goto exit_no_settings;
+
+	/* only write settings back if activation state is different */
+	if (kone->settings.tcu != state) {
+		kone->settings.tcu = state;
+		kone_set_settings_checksum(&kone->settings);
+
+		retval = kone_set_settings(usb_dev, &kone->settings);
+		if (retval) {
+			dev_err(&usb_dev->dev, "couldn't set tcu state\n");
+			/*
+			 * try to reread valid settings into buffer overwriting
+			 * first error code
+			 */
+			retval = kone_get_settings(usb_dev, &kone->settings);
+			if (retval)
+				goto exit_no_settings;
+			goto exit_unlock;
+		}
+	}
+
+	retval = size;
+exit_no_settings:
+	dev_err(&usb_dev->dev, "couldn't read settings\n");
+exit_unlock:
+	mutex_unlock(&kone->kone_lock);
+	return retval;
+}
+
+static ssize_t kone_sysfs_show_startup_profile(struct device *dev,
+		struct device_attribute *attr, char *buf)
+{
+	struct kone_device *kone = hid_get_drvdata(dev_get_drvdata(dev));
+	return snprintf(buf, PAGE_SIZE, "%d\n", kone->settings.startup_profile);
+}
+
+static ssize_t kone_sysfs_set_startup_profile(struct device *dev,
+		struct device_attribute *attr, char const *buf, size_t size)
+{
+	struct kone_device *kone = hid_get_drvdata(dev_get_drvdata(dev));
+	struct usb_device *usb_dev = interface_to_usbdev(to_usb_interface(dev));
+	int retval;
+	unsigned long new_startup_profile;
+
+	retval = strict_strtoul(buf, 10, &new_startup_profile);
+	if (retval)
+		return retval;
+
+	if (new_startup_profile  < 1 || new_startup_profile > 5)
+		return -EINVAL;
+
+	mutex_lock(&kone->kone_lock);
+
+	kone->settings.startup_profile = new_startup_profile;
+	kone_set_settings_checksum(&kone->settings);
+
+	retval = kone_set_settings(usb_dev, &kone->settings);
+
+	mutex_unlock(&kone->kone_lock);
+
+	if (retval)
+		return retval;
+
+	/* changing the startup profile immediately activates this profile */
+	kone->actual_profile = new_startup_profile;
+	kone->actual_dpi = kone->profiles[kone->actual_profile - 1].startup_dpi;
+
+	return size;
+}
+
+/*
+ * This file is used by userland software to find devices that are handled by
+ * this driver. This provides a consistent way for actual and older kernels
+ * where this driver replaced usbhid instead of generic-usb.
+ * Driver capabilities are determined by version number.
+ */
+static ssize_t kone_sysfs_show_driver_version(struct device *dev,
+		struct device_attribute *attr, char *buf)
+{
+	return snprintf(buf, PAGE_SIZE, ROCCAT_KONE_DRIVER_VERSION "\n");
+}
+
+/*
+ * Read actual dpi settings.
+ * Returns raw value for further processing. Refer to enum kone_polling_rates to
+ * get real value.
+ */
+static DEVICE_ATTR(actual_dpi, 0440, kone_sysfs_show_actual_dpi, NULL);
+
+static DEVICE_ATTR(actual_profile, 0440, kone_sysfs_show_actual_profile, NULL);
+
+/*
+ * The mouse can be equipped with one of four supplied weights from 5 to 20
+ * grams which are recognized and its value can be read out.
+ * This returns the raw value reported by the mouse for easy evaluation by
+ * software. Refer to enum kone_weights to get corresponding real weight.
+ */
+static DEVICE_ATTR(weight, 0440, kone_sysfs_show_weight, NULL);
+
+/*
+ * Prints firmware version stored in mouse as integer.
+ * The raw value reported by the mouse is returned for easy evaluation, to get
+ * the real version number the decimal point has to be shifted 2 positions to
+ * the left. E.g. a value of 138 means 1.38.
+ */
+static DEVICE_ATTR(firmware_version, 0440,
+		kone_sysfs_show_firmware_version, NULL);
+
+/*
+ * Prints state of Tracking Control Unit as number where 0 = off and 1 = on
+ * Writing 0 deactivates tcu and writing 1 calibrates and activates the tcu
+ */
+static DEVICE_ATTR(tcu, 0660, kone_sysfs_show_tcu, kone_sysfs_set_tcu);
+
+/* Prints and takes the number of the profile the mouse starts with */
+static DEVICE_ATTR(startup_profile, 0660,
+		kone_sysfs_show_startup_profile,
+		kone_sysfs_set_startup_profile);
+
+static DEVICE_ATTR(kone_driver_version, 0440,
+		kone_sysfs_show_driver_version, NULL);
+
+static struct attribute *kone_attributes[] = {
+		&dev_attr_actual_dpi.attr,
+		&dev_attr_actual_profile.attr,
+		&dev_attr_weight.attr,
+		&dev_attr_firmware_version.attr,
+		&dev_attr_tcu.attr,
+		&dev_attr_startup_profile.attr,
+		&dev_attr_kone_driver_version.attr,
+		NULL
+};
+
+static struct attribute_group kone_attribute_group = {
+		.attrs = kone_attributes
+};
+
+static struct bin_attribute kone_settings_attr = {
+	.attr = { .name = "settings", .mode = 0660 },
+	.size = sizeof(struct kone_settings),
+	.read = kone_sysfs_read_settings,
+	.write = kone_sysfs_write_settings
+};
+
+static struct bin_attribute kone_profile1_attr = {
+	.attr = { .name = "profile1", .mode = 0660 },
+	.size = sizeof(struct kone_profile),
+	.read = kone_sysfs_read_profile1,
+	.write = kone_sysfs_write_profile1
+};
+
+static struct bin_attribute kone_profile2_attr = {
+	.attr = { .name = "profile2", .mode = 0660 },
+	.size = sizeof(struct kone_profile),
+	.read = kone_sysfs_read_profile2,
+	.write = kone_sysfs_write_profile2
+};
+
+static struct bin_attribute kone_profile3_attr = {
+	.attr = { .name = "profile3", .mode = 0660 },
+	.size = sizeof(struct kone_profile),
+	.read = kone_sysfs_read_profile3,
+	.write = kone_sysfs_write_profile3
+};
+
+static struct bin_attribute kone_profile4_attr = {
+	.attr = { .name = "profile4", .mode = 0660 },
+	.size = sizeof(struct kone_profile),
+	.read = kone_sysfs_read_profile4,
+	.write = kone_sysfs_write_profile4
+};
+
+static struct bin_attribute kone_profile5_attr = {
+	.attr = { .name = "profile5", .mode = 0660 },
+	.size = sizeof(struct kone_profile),
+	.read = kone_sysfs_read_profile5,
+	.write = kone_sysfs_write_profile5
+};
+
+static int kone_create_sysfs_attributes(struct usb_interface *intf)
+{
+	int retval;
+
+	retval = sysfs_create_group(&intf->dev.kobj, &kone_attribute_group);
+	if (retval)
+		goto exit_1;
+
+	retval = sysfs_create_bin_file(&intf->dev.kobj, &kone_settings_attr);
+	if (retval)
+		goto exit_2;
+
+	retval = sysfs_create_bin_file(&intf->dev.kobj, &kone_profile1_attr);
+	if (retval)
+		goto exit_3;
+
+	retval = sysfs_create_bin_file(&intf->dev.kobj, &kone_profile2_attr);
+	if (retval)
+		goto exit_4;
+
+	retval = sysfs_create_bin_file(&intf->dev.kobj, &kone_profile3_attr);
+	if (retval)
+		goto exit_5;
+
+	retval = sysfs_create_bin_file(&intf->dev.kobj, &kone_profile4_attr);
+	if (retval)
+		goto exit_6;
+
+	retval = sysfs_create_bin_file(&intf->dev.kobj, &kone_profile5_attr);
+	if (retval)
+		goto exit_7;
+
+	return 0;
+
+exit_7:
+	sysfs_remove_bin_file(&intf->dev.kobj, &kone_profile4_attr);
+exit_6:
+	sysfs_remove_bin_file(&intf->dev.kobj, &kone_profile3_attr);
+exit_5:
+	sysfs_remove_bin_file(&intf->dev.kobj, &kone_profile2_attr);
+exit_4:
+	sysfs_remove_bin_file(&intf->dev.kobj, &kone_profile1_attr);
+exit_3:
+	sysfs_remove_bin_file(&intf->dev.kobj, &kone_settings_attr);
+exit_2:
+	sysfs_remove_group(&intf->dev.kobj, &kone_attribute_group);
+exit_1:
+	return retval;
+}
+
+static void kone_remove_sysfs_attributes(struct usb_interface *intf)
+{
+	sysfs_remove_bin_file(&intf->dev.kobj, &kone_profile5_attr);
+	sysfs_remove_bin_file(&intf->dev.kobj, &kone_profile4_attr);
+	sysfs_remove_bin_file(&intf->dev.kobj, &kone_profile3_attr);
+	sysfs_remove_bin_file(&intf->dev.kobj, &kone_profile2_attr);
+	sysfs_remove_bin_file(&intf->dev.kobj, &kone_profile1_attr);
+	sysfs_remove_bin_file(&intf->dev.kobj, &kone_settings_attr);
+	sysfs_remove_group(&intf->dev.kobj, &kone_attribute_group);
+}
+
+static int kone_init_kone_device_struct(struct usb_device *usb_dev,
+		struct kone_device *kone)
+{
+	uint i;
+	int retval;
+
+	mutex_init(&kone->kone_lock);
+
+	for (i = 0; i < 5; ++i) {
+		retval = kone_get_profile(usb_dev, &kone->profiles[i], i + 1);
+		if (retval)
+			return retval;
+	}
+
+	retval = kone_get_settings(usb_dev, &kone->settings);
+	if (retval)
+		return retval;
+
+	retval = kone_get_firmware_version(usb_dev, &kone->firmware_version);
+	if (retval)
+		return retval;
+
+	kone->actual_profile = kone->settings.startup_profile;
+	kone->actual_dpi = kone->profiles[kone->actual_profile].startup_dpi;
+
+	return 0;
+}
+
+/*
+ * Since IGNORE_MOUSE quirk moved to hid-apple, there is no way to bind only to
+ * mousepart if usb_hid is compiled into the kernel and kone is compiled as
+ * module.
+ * Secial behaviour is bound only to mousepart since only mouseevents contain
+ * additional notifications.
+ */
+static int kone_init_specials(struct hid_device *hdev)
+{
+	struct usb_interface *intf = to_usb_interface(hdev->dev.parent);
+	struct usb_device *usb_dev = interface_to_usbdev(intf);
+	struct kone_device *kone;
+	int retval;
+
+	if (intf->cur_altsetting->desc.bInterfaceProtocol
+			== USB_INTERFACE_PROTOCOL_MOUSE) {
+
+		kone = kzalloc(sizeof(*kone), GFP_KERNEL);
+		if (!kone) {
+			dev_err(&hdev->dev, "can't alloc device descriptor\n");
+			return -ENOMEM;
+		}
+		hid_set_drvdata(hdev, kone);
+
+		retval = kone_init_kone_device_struct(usb_dev, kone);
+		if (retval) {
+			dev_err(&hdev->dev,
+					"couldn't init struct kone_device\n");
+			goto exit_free;
+		}
+		retval = kone_create_sysfs_attributes(intf);
+		if (retval) {
+			dev_err(&hdev->dev, "cannot create sysfs files\n");
+			goto exit_free;
+		}
+	} else {
+		hid_set_drvdata(hdev, NULL);
+	}
+
+	return 0;
+exit_free:
+	kfree(kone);
+	return retval;
+}
+
+
+static void kone_remove_specials(struct hid_device *hdev)
+{
+	struct usb_interface *intf = to_usb_interface(hdev->dev.parent);
+
+	if (intf->cur_altsetting->desc.bInterfaceProtocol
+			== USB_INTERFACE_PROTOCOL_MOUSE) {
+		kone_remove_sysfs_attributes(intf);
+		kfree(hid_get_drvdata(hdev));
+	}
+}
+
+static int kone_probe(struct hid_device *hdev, const struct hid_device_id *id)
+{
+	int retval;
+
+	retval = hid_parse(hdev);
+	if (retval) {
+		dev_err(&hdev->dev, "parse failed\n");
+		goto exit;
+	}
+
+	retval = hid_hw_start(hdev, HID_CONNECT_DEFAULT);
+	if (retval) {
+		dev_err(&hdev->dev, "hw start failed\n");
+		goto exit;
+	}
+
+	retval = kone_init_specials(hdev);
+	if (retval) {
+		dev_err(&hdev->dev, "couldn't install mouse\n");
+		goto exit_stop;
+	}
+
+	return 0;
+
+exit_stop:
+	hid_hw_stop(hdev);
+exit:
+	return retval;
+}
+
+static void kone_remove(struct hid_device *hdev)
+{
+	kone_remove_specials(hdev);
+	hid_hw_stop(hdev);
+}
+
+/* handle special events and keep actual profile and dpi values up to date */
+static void kone_keep_values_up_to_date(struct kone_device *kone,
+		struct kone_mouse_event const *event)
+{
+	switch (event->event) {
+	case kone_mouse_event_switch_profile:
+	case kone_mouse_event_osd_profile:
+		kone->actual_profile = event->value;
+		kone->actual_dpi = kone->profiles[kone->actual_profile - 1].
+				startup_dpi;
+		break;
+	case kone_mouse_event_switch_dpi:
+	case kone_mouse_event_osd_dpi:
+		kone->actual_dpi = event->value;
+		break;
+	}
+}
+
+/*
+ * Is called for keyboard- and mousepart.
+ * Only mousepart gets informations about special events in its extended event
+ * structure.
+ */
+static int kone_raw_event(struct hid_device *hdev, struct hid_report *report,
+		u8 *data, int size)
+{
+	struct kone_device *kone = hid_get_drvdata(hdev);
+	struct kone_mouse_event *event = (struct kone_mouse_event *)data;
+
+	/* keyboard events are always processed by default handler */
+	if (size != sizeof(struct kone_mouse_event))
+		return 0;
+
+	/*
+	 * Firmware 1.38 introduced new behaviour for tilt and special buttons.
+	 * Pressed button is reported in each movement event.
+	 * Workaround sends only one event per press.
+	 */
+	if (memcmp(&kone->last_mouse_event.tilt, &event->tilt, 5))
+		memcpy(&kone->last_mouse_event, event,
+				sizeof(struct kone_mouse_event));
+	else
+		memset(&event->tilt, 0, 5);
+
+	kone_keep_values_up_to_date(kone, event);
+
+	return 0; /* always do further processing */
+}
+
+static const struct hid_device_id kone_devices[] = {
+	{ HID_USB_DEVICE(USB_VENDOR_ID_ROCCAT, USB_DEVICE_ID_ROCCAT_KONE) },
+	{ }
+};
+
+MODULE_DEVICE_TABLE(hid, kone_devices);
+
+static struct hid_driver kone_driver = {
+		.name = "kone",
+		.id_table = kone_devices,
+		.probe = kone_probe,
+		.remove = kone_remove,
+		.raw_event = kone_raw_event
+};
+
+static int __init kone_init(void)
+{
+	return hid_register_driver(&kone_driver);
+}
+
+static void __exit kone_exit(void)
+{
+	hid_unregister_driver(&kone_driver);
+}
+
+module_init(kone_init);
+module_exit(kone_exit);
+
+MODULE_AUTHOR("Stefan Achatz");
+MODULE_DESCRIPTION("USB Roccat Kone driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/hid/hid-roccat-kone.h b/drivers/hid/hid-roccat-kone.h
new file mode 100644
index 0000000..b413b10
--- /dev/null
+++ b/drivers/hid/hid-roccat-kone.h
@@ -0,0 +1,224 @@
+#ifndef __HID_ROCCAT_KONE_H
+#define __HID_ROCCAT_KONE_H
+
+/*
+ * Copyright (c) 2010 Stefan Achatz <erazor_de@users.sourceforge.net>
+ */
+
+/*
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ */
+
+#include <linux/types.h>
+
+#define ROCCAT_KONE_DRIVER_VERSION "v0.3.1"
+
+#pragma pack(push)
+#pragma pack(1)
+
+struct kone_keystroke {
+	uint8_t key;
+	uint8_t action;
+	uint16_t period; /* in milliseconds */
+};
+
+enum kone_keystroke_buttons {
+	kone_keystroke_button_1 = 0xf0, /* left mouse button */
+	kone_keystroke_button_2 = 0xf1, /* right mouse button */
+	kone_keystroke_button_3 = 0xf2, /* wheel */
+	kone_keystroke_button_9 = 0xf3, /* side button up */
+	kone_keystroke_button_8 = 0xf4 /* side button down */
+};
+
+enum kone_keystroke_actions {
+	kone_keystroke_action_press = 0,
+	kone_keystroke_action_release = 1
+};
+
+struct kone_button_info {
+	uint8_t number; /* range 1-8 */
+	uint8_t type;
+	uint8_t macro_type; /* 0 = short, 1 = overlong */
+	uint8_t macro_set_name[16]; /* can be max 15 chars long */
+	uint8_t macro_name[16]; /* can be max 15 chars long */
+	uint8_t count;
+	struct kone_keystroke keystrokes[20];
+};
+
+enum kone_button_info_types {
+	/* valid button types until firmware 1.32 */
+	kone_button_info_type_button_1 = 0x1, /* click (left mouse button) */
+	kone_button_info_type_button_2 = 0x2, /* menu (right mouse button)*/
+	kone_button_info_type_button_3 = 0x3, /* scroll (wheel) */
+	kone_button_info_type_double_click = 0x4,
+	kone_button_info_type_key = 0x5,
+	kone_button_info_type_macro = 0x6,
+	kone_button_info_type_off = 0x7,
+	/* TODO clarify function and rename */
+	kone_button_info_type_osd_xy_prescaling = 0x8,
+	kone_button_info_type_osd_dpi = 0x9,
+	kone_button_info_type_osd_profile = 0xa,
+	kone_button_info_type_button_9 = 0xb, /* ie forward */
+	kone_button_info_type_button_8 = 0xc, /* ie backward */
+	kone_button_info_type_dpi_up = 0xd, /* internal */
+	kone_button_info_type_dpi_down = 0xe, /* internal */
+	kone_button_info_type_button_7 = 0xf, /* tilt left */
+	kone_button_info_type_button_6 = 0x10, /* tilt right */
+	kone_button_info_type_profile_up = 0x11, /* internal */
+	kone_button_info_type_profile_down = 0x12, /* internal */
+	/* additional valid button types since firmware 1.38 */
+	kone_button_info_type_multimedia_open_player = 0x20,
+	kone_button_info_type_multimedia_next_track = 0x21,
+	kone_button_info_type_multimedia_prev_track = 0x22,
+	kone_button_info_type_multimedia_play_pause = 0x23,
+	kone_button_info_type_multimedia_stop = 0x24,
+	kone_button_info_type_multimedia_mute = 0x25,
+	kone_button_info_type_multimedia_volume_up = 0x26,
+	kone_button_info_type_multimedia_volume_down = 0x27
+};
+
+enum kone_button_info_numbers {
+	kone_button_top = 1,
+	kone_button_wheel_tilt_left = 2,
+	kone_button_wheel_tilt_right = 3,
+	kone_button_forward = 4,
+	kone_button_backward = 5,
+	kone_button_middle = 6,
+	kone_button_plus = 7,
+	kone_button_minus = 8,
+};
+
+struct kone_light_info {
+	uint8_t number; /* number of light 1-5 */
+	uint8_t mod;   /* 1 = on, 2 = off */
+	uint8_t red;   /* range 0x00-0xff */
+	uint8_t green; /* range 0x00-0xff */
+	uint8_t blue;  /* range 0x00-0xff */
+};
+
+struct kone_profile {
+	uint16_t size; /* always 975 */
+	uint16_t unused; /* always 0 */
+
+	/*
+	 * range 1-5
+	 * This number does not need to correspond with location where profile
+	 * saved
+	 */
+	uint8_t profile; /* range 1-5 */
+
+	uint16_t main_sensitivity; /* range 100-1000 */
+	uint8_t xy_sensitivity_enabled; /* 1 = on, 2 = off */
+	uint16_t x_sensitivity; /* range 100-1000 */
+	uint16_t y_sensitivity; /* range 100-1000 */
+	uint8_t dpi_rate; /* bit 1 = 800, ... */
+	uint8_t startup_dpi; /* range 1-6 */
+	uint8_t polling_rate; /* 1 = 125Hz, 2 = 500Hz, 3 = 1000Hz */
+	/* kone has no dcu
+	 * value is always 2 in firmwares <= 1.32 and
+	 * 1 in firmwares > 1.32
+	 */
+	uint8_t dcu_flag;
+	uint8_t light_effect_1; /* range 1-3 */
+	uint8_t light_effect_2; /* range 1-5 */
+	uint8_t light_effect_3; /* range 1-4 */
+	uint8_t light_effect_speed; /* range 0-255 */
+
+	struct kone_light_info light_infos[5];
+	/* offset is kone_button_info_numbers - 1 */
+	struct kone_button_info button_infos[8];
+
+	uint16_t checksum; /* \brief holds checksum of struct */
+};
+
+enum kone_polling_rates {
+	kone_polling_rate_125 = 1,
+	kone_polling_rate_500 = 2,
+	kone_polling_rate_1000 = 3
+};
+
+struct kone_settings {
+	uint16_t size; /* always 36 */
+	uint8_t  startup_profile; /* 1-5 */
+	uint8_t	 unknown1;
+	uint8_t  tcu; /* 0 = off, 1 = on */
+	uint8_t  unknown2[23];
+	uint8_t  calibration_data[4];
+	uint8_t  unknown3[2];
+	uint16_t checksum;
+};
+
+/*
+ * 12 byte mouse event read by interrupt_read
+ */
+struct kone_mouse_event {
+	uint8_t report_number; /* always 1 */
+	uint8_t button;
+	uint16_t x;
+	uint16_t y;
+	uint8_t wheel; /* up = 1, down = -1 */
+	uint8_t tilt; /* right = 1, left = -1 */
+	uint8_t unknown;
+	uint8_t event;
+	uint8_t value; /* press = 0, release = 1 */
+	uint8_t macro_key; /* 0 to 8 */
+};
+
+enum kone_mouse_events {
+	/* osd events are thought to be display on screen */
+	kone_mouse_event_osd_dpi = 0xa0,
+	kone_mouse_event_osd_profile = 0xb0,
+	/* TODO clarify meaning and occurence of kone_mouse_event_calibration */
+	kone_mouse_event_calibration = 0xc0,
+	kone_mouse_event_call_overlong_macro = 0xe0,
+	/* switch events notify if user changed values with mousebutton click */
+	kone_mouse_event_switch_dpi = 0xf0,
+	kone_mouse_event_switch_profile = 0xf1
+};
+
+enum kone_commands {
+	kone_command_profile = 0x5a,
+	kone_command_settings = 0x15a,
+	kone_command_firmware_version = 0x25a,
+	kone_command_weight = 0x45a,
+	kone_command_calibrate = 0x55a,
+	kone_command_confirm_write = 0x65a,
+	kone_command_firmware = 0xe5a
+};
+
+#pragma pack(pop)
+
+struct kone_device {
+	/*
+	 * Storing actual values when we get informed about changes since there
+	 * is no way of getting this information from the device on demand
+	 */
+	int actual_profile, actual_dpi;
+	/* Used for neutralizing abnormal button behaviour */
+	struct kone_mouse_event last_mouse_event;
+
+	/*
+	 * It's unlikely that multiple sysfs attributes are accessed at a time,
+	 * so only one mutex is used to secure hardware access and profiles and
+	 * settings of this struct.
+	 */
+	struct mutex kone_lock;
+
+	/*
+	 * Storing the data here reduces IO and ensures that data is available
+	 * when its needed (E.g. interrupt handler).
+	 */
+	struct kone_profile profiles[5];
+	struct kone_settings settings;
+
+	/*
+	 * firmware doesn't change unless firmware update is implemented,
+	 * so it's read only once
+	 */
+	int firmware_version;
+};
+
+#endif
diff --git a/drivers/hid/hid-samsung.c b/drivers/hid/hid-samsung.c
index 510dd13..bda0fd6 100644
--- a/drivers/hid/hid-samsung.c
+++ b/drivers/hid/hid-samsung.c
@@ -7,6 +7,18 @@
  *  Copyright (c) 2006-2007 Jiri Kosina
  *  Copyright (c) 2007 Paul Walmsley
  *  Copyright (c) 2008 Jiri Slaby
+ *  Copyright (c) 2010 Don Prince <dhprince.devel@yahoo.co.uk>
+ *
+ *
+ *  This driver supports several HID devices:
+ *
+ *  [0419:0001] Samsung IrDA remote controller (reports as Cypress USB Mouse).
+ *	various hid report fixups for different variants.
+ *
+ *  [0419:0600] Creative Desktop Wireless 6000 keyboard/mouse combo
+ *	several key mappings used from the consumer usage page
+ *	deviate from the USB HUT 1.12 standard.
+ *
  */
 
 /*
@@ -17,14 +29,13 @@
  */
 
 #include <linux/device.h>
+#include <linux/usb.h>
 #include <linux/hid.h>
 #include <linux/module.h>
 
 #include "hid-ids.h"
 
 /*
- * Samsung IrDA remote controller (reports as Cypress USB Mouse).
- *
  * There are several variants for 0419:0001:
  *
  * 1. 184 byte report descriptor
@@ -43,21 +54,21 @@
  * 4. 171 byte report descriptor
  * Report #3 has an array field with logical range 0..1 instead of 1..3.
  */
-static inline void samsung_dev_trace(struct hid_device *hdev,
+static inline void samsung_irda_dev_trace(struct hid_device *hdev,
 		unsigned int rsize)
 {
 	dev_info(&hdev->dev, "fixing up Samsung IrDA %d byte report "
 			"descriptor\n", rsize);
 }
 
-static void samsung_report_fixup(struct hid_device *hdev, __u8 *rdesc,
+static void samsung_irda_report_fixup(struct hid_device *hdev, __u8 *rdesc,
 		unsigned int rsize)
 {
 	if (rsize == 184 && rdesc[175] == 0x25 && rdesc[176] == 0x40 &&
 			rdesc[177] == 0x75 && rdesc[178] == 0x30 &&
 			rdesc[179] == 0x95 && rdesc[180] == 0x01 &&
 			rdesc[182] == 0x40) {
-		samsung_dev_trace(hdev, 184);
+		samsung_irda_dev_trace(hdev, 184);
 		rdesc[176] = 0xff;
 		rdesc[178] = 0x08;
 		rdesc[180] = 0x06;
@@ -65,24 +76,80 @@
 	} else
 	if (rsize == 203 && rdesc[192] == 0x15 && rdesc[193] == 0x0 &&
 			rdesc[194] == 0x25 && rdesc[195] == 0x12) {
-		samsung_dev_trace(hdev, 203);
+		samsung_irda_dev_trace(hdev, 203);
 		rdesc[193] = 0x1;
 		rdesc[195] = 0xf;
 	} else
 	if (rsize == 135 && rdesc[124] == 0x15 && rdesc[125] == 0x0 &&
 			rdesc[126] == 0x25 && rdesc[127] == 0x11) {
-		samsung_dev_trace(hdev, 135);
+		samsung_irda_dev_trace(hdev, 135);
 		rdesc[125] = 0x1;
 		rdesc[127] = 0xe;
 	} else
 	if (rsize == 171 && rdesc[160] == 0x15 && rdesc[161] == 0x0 &&
 			rdesc[162] == 0x25 && rdesc[163] == 0x01) {
-		samsung_dev_trace(hdev, 171);
+		samsung_irda_dev_trace(hdev, 171);
 		rdesc[161] = 0x1;
 		rdesc[163] = 0x3;
 	}
 }
 
+#define samsung_kbd_mouse_map_key_clear(c) \
+	hid_map_usage_clear(hi, usage, bit, max, EV_KEY, (c))
+
+static int samsung_kbd_mouse_input_mapping(struct hid_device *hdev,
+	struct hid_input *hi, struct hid_field *field, struct hid_usage *usage,
+	unsigned long **bit, int *max)
+{
+	struct usb_interface *intf = to_usb_interface(hdev->dev.parent);
+	unsigned short ifnum = intf->cur_altsetting->desc.bInterfaceNumber;
+
+	if (1 != ifnum || HID_UP_CONSUMER != (usage->hid & HID_USAGE_PAGE))
+		return 0;
+
+	dbg_hid("samsung wireless keyboard/mouse input mapping event [0x%x]\n",
+		usage->hid & HID_USAGE);
+
+	switch (usage->hid & HID_USAGE) {
+	/* report 2 */
+	case 0x183: samsung_kbd_mouse_map_key_clear(KEY_MEDIA); break;
+	case 0x195: samsung_kbd_mouse_map_key_clear(KEY_EMAIL);	break;
+	case 0x196: samsung_kbd_mouse_map_key_clear(KEY_CALC); break;
+	case 0x197: samsung_kbd_mouse_map_key_clear(KEY_COMPUTER); break;
+	case 0x22b: samsung_kbd_mouse_map_key_clear(KEY_SEARCH); break;
+	case 0x22c: samsung_kbd_mouse_map_key_clear(KEY_WWW); break;
+	case 0x22d: samsung_kbd_mouse_map_key_clear(KEY_BACK); break;
+	case 0x22e: samsung_kbd_mouse_map_key_clear(KEY_FORWARD); break;
+	case 0x22f: samsung_kbd_mouse_map_key_clear(KEY_FAVORITES); break;
+	case 0x230: samsung_kbd_mouse_map_key_clear(KEY_REFRESH); break;
+	case 0x231: samsung_kbd_mouse_map_key_clear(KEY_STOP); break;
+	default:
+		return 0;
+	}
+
+	return 1;
+}
+
+static void samsung_report_fixup(struct hid_device *hdev, __u8 *rdesc,
+	unsigned int rsize)
+{
+	if (USB_DEVICE_ID_SAMSUNG_IR_REMOTE == hdev->product)
+		samsung_irda_report_fixup(hdev, rdesc, rsize);
+}
+
+static int samsung_input_mapping(struct hid_device *hdev, struct hid_input *hi,
+	struct hid_field *field, struct hid_usage *usage,
+	unsigned long **bit, int *max)
+{
+	int ret = 0;
+
+	if (USB_DEVICE_ID_SAMSUNG_WIRELESS_KBD_MOUSE == hdev->product)
+		ret = samsung_kbd_mouse_input_mapping(hdev,
+			hi, field, usage, bit, max);
+
+	return ret;
+}
+
 static int samsung_probe(struct hid_device *hdev,
 		const struct hid_device_id *id)
 {
@@ -95,10 +162,12 @@
 		goto err_free;
 	}
 
-	if (hdev->rsize == 184) {
-		/* disable hidinput, force hiddev */
-		cmask = (cmask & ~HID_CONNECT_HIDINPUT) |
-			HID_CONNECT_HIDDEV_FORCE;
+	if (USB_DEVICE_ID_SAMSUNG_IR_REMOTE == hdev->product) {
+		if (hdev->rsize == 184) {
+			/* disable hidinput, force hiddev */
+			cmask = (cmask & ~HID_CONNECT_HIDINPUT) |
+				HID_CONNECT_HIDDEV_FORCE;
+		}
 	}
 
 	ret = hid_hw_start(hdev, cmask);
@@ -114,6 +183,7 @@
 
 static const struct hid_device_id samsung_devices[] = {
 	{ HID_USB_DEVICE(USB_VENDOR_ID_SAMSUNG, USB_DEVICE_ID_SAMSUNG_IR_REMOTE) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_SAMSUNG, USB_DEVICE_ID_SAMSUNG_WIRELESS_KBD_MOUSE) },
 	{ }
 };
 MODULE_DEVICE_TABLE(hid, samsung_devices);
@@ -122,6 +192,7 @@
 	.name = "samsung",
 	.id_table = samsung_devices,
 	.report_fixup = samsung_report_fixup,
+	.input_mapping = samsung_input_mapping,
 	.probe = samsung_probe,
 };
 
diff --git a/drivers/hid/hid-topseed.c b/drivers/hid/hid-topseed.c
index 6925eda..2eebdcc 100644
--- a/drivers/hid/hid-topseed.c
+++ b/drivers/hid/hid-topseed.c
@@ -3,6 +3,9 @@
  *
  *  Copyright (c) 2008 Lev Babiev
  *  based on hid-cherry driver
+ *
+ *  Modified to also support BTC "Emprex 3009URF III Vista MCE Remote" by
+ *  Wayne Thomas 2010.
  */
 
 /*
@@ -24,23 +27,29 @@
 		struct hid_field *field, struct hid_usage *usage,
 		unsigned long **bit, int *max)
 {
-	if ((usage->hid & HID_USAGE_PAGE) != 0x0ffbc0000)
+	if ((usage->hid & HID_USAGE_PAGE) != HID_UP_LOGIVENDOR)
 		return 0;
 
 	switch (usage->hid & HID_USAGE) {
-        case 0x00d: ts_map_key_clear(KEY_HOME);           break;
-        case 0x024: ts_map_key_clear(KEY_MENU);           break;
-        case 0x025: ts_map_key_clear(KEY_TV);             break;
-        case 0x048: ts_map_key_clear(KEY_RED);            break;
-        case 0x047: ts_map_key_clear(KEY_GREEN);          break;
-        case 0x049: ts_map_key_clear(KEY_YELLOW);         break;
-        case 0x04a: ts_map_key_clear(KEY_BLUE);           break;
-        case 0x04b: ts_map_key_clear(KEY_ANGLE);          break;
-        case 0x04c: ts_map_key_clear(KEY_LANGUAGE);       break;
-        case 0x04d: ts_map_key_clear(KEY_SUBTITLE);       break;
-        case 0x031: ts_map_key_clear(KEY_AUDIO);          break;
-        case 0x032: ts_map_key_clear(KEY_TEXT);           break;
-        case 0x033: ts_map_key_clear(KEY_CHANNEL);        break;
+	case 0x00d: ts_map_key_clear(KEY_MEDIA);	break;
+	case 0x024: ts_map_key_clear(KEY_MENU);		break;
+	case 0x025: ts_map_key_clear(KEY_TV);		break;
+	case 0x031: ts_map_key_clear(KEY_AUDIO);	break;
+	case 0x032: ts_map_key_clear(KEY_TEXT);		break;
+	case 0x033: ts_map_key_clear(KEY_CHANNEL);	break;
+	case 0x047: ts_map_key_clear(KEY_MP3);		break;
+	case 0x048: ts_map_key_clear(KEY_TV2);		break;
+	case 0x049: ts_map_key_clear(KEY_CAMERA);	break;
+	case 0x04a: ts_map_key_clear(KEY_VIDEO);	break;
+	case 0x04b: ts_map_key_clear(KEY_ANGLE);	break;
+	case 0x04c: ts_map_key_clear(KEY_LANGUAGE);	break;
+	case 0x04d: ts_map_key_clear(KEY_SUBTITLE);	break;
+	case 0x050: ts_map_key_clear(KEY_RADIO);	break;
+	case 0x05a: ts_map_key_clear(KEY_TEXT);		break;
+	case 0x05b: ts_map_key_clear(KEY_RED);		break;
+	case 0x05c: ts_map_key_clear(KEY_GREEN);	break;
+	case 0x05d: ts_map_key_clear(KEY_YELLOW);	break;
+	case 0x05e: ts_map_key_clear(KEY_BLUE);		break;
 	default:
 		return 0;
 	}
@@ -50,6 +59,7 @@
 
 static const struct hid_device_id ts_devices[] = {
 	{ HID_USB_DEVICE(USB_VENDOR_ID_TOPSEED, USB_DEVICE_ID_TOPSEED_CYBERLINK) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_BTC, USB_DEVICE_ID_BTC_EMPREX_REMOTE) },
 	{ }
 };
 MODULE_DEVICE_TABLE(hid, ts_devices);
diff --git a/drivers/hid/hid-wacom.c b/drivers/hid/hid-wacom.c
index f947d83..1e051f1 100644
--- a/drivers/hid/hid-wacom.c
+++ b/drivers/hid/hid-wacom.c
@@ -22,14 +22,159 @@
 #include <linux/hid.h>
 #include <linux/module.h>
 #include <linux/slab.h>
+#ifdef CONFIG_HID_WACOM_POWER_SUPPLY
+#include <linux/power_supply.h>
+#endif
 
 #include "hid-ids.h"
 
 struct wacom_data {
 	__u16 tool;
 	unsigned char butstate;
+	unsigned char high_speed;
+#ifdef CONFIG_HID_WACOM_POWER_SUPPLY
+	int battery_capacity;
+	struct power_supply battery;
+	struct power_supply ac;
+#endif
 };
 
+#ifdef CONFIG_HID_WACOM_POWER_SUPPLY
+/*percent of battery capacity, 0 means AC online*/
+static unsigned short batcap[8] = { 1, 15, 25, 35, 50, 70, 100, 0 };
+
+static enum power_supply_property wacom_battery_props[] = {
+	POWER_SUPPLY_PROP_PRESENT,
+	POWER_SUPPLY_PROP_CAPACITY
+};
+
+static enum power_supply_property wacom_ac_props[] = {
+	POWER_SUPPLY_PROP_PRESENT,
+	POWER_SUPPLY_PROP_ONLINE
+};
+
+static int wacom_battery_get_property(struct power_supply *psy,
+				enum power_supply_property psp,
+				union power_supply_propval *val)
+{
+	struct wacom_data *wdata = container_of(psy,
+					struct wacom_data, battery);
+	int power_state = batcap[wdata->battery_capacity];
+	int ret = 0;
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_PRESENT:
+		val->intval = 1;
+		break;
+	case POWER_SUPPLY_PROP_CAPACITY:
+		/* show 100% battery capacity when charging */
+		if (power_state == 0)
+			val->intval = 100;
+		else
+			val->intval = power_state;
+		break;
+	default:
+		ret = -EINVAL;
+		break;
+	}
+	return ret;
+}
+
+static int wacom_ac_get_property(struct power_supply *psy,
+				enum power_supply_property psp,
+				union power_supply_propval *val)
+{
+	struct wacom_data *wdata = container_of(psy, struct wacom_data, ac);
+	int power_state = batcap[wdata->battery_capacity];
+	int ret = 0;
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_PRESENT:
+		/* fall through */
+	case POWER_SUPPLY_PROP_ONLINE:
+		if (power_state == 0)
+			val->intval = 1;
+		else
+			val->intval = 0;
+		break;
+	default:
+		ret = -EINVAL;
+		break;
+	}
+	return ret;
+}
+#endif
+
+static void wacom_poke(struct hid_device *hdev, u8 speed)
+{
+	struct wacom_data *wdata = hid_get_drvdata(hdev);
+	int limit, ret;
+	char rep_data[2];
+
+	rep_data[0] = 0x03 ; rep_data[1] = 0x00;
+	limit = 3;
+	do {
+		ret = hdev->hid_output_raw_report(hdev, rep_data, 2,
+				HID_FEATURE_REPORT);
+	} while (ret < 0 && limit-- > 0);
+
+	if (ret >= 0) {
+		if (speed == 0)
+			rep_data[0] = 0x05;
+		else
+			rep_data[0] = 0x06;
+
+		rep_data[1] = 0x00;
+		limit = 3;
+		do {
+			ret = hdev->hid_output_raw_report(hdev, rep_data, 2,
+					HID_FEATURE_REPORT);
+		} while (ret < 0 && limit-- > 0);
+
+		if (ret >= 0) {
+			wdata->high_speed = speed;
+			return;
+		}
+	}
+
+	/*
+	 * Note that if the raw queries fail, it's not a hard failure and it
+	 * is safe to continue
+	 */
+	dev_warn(&hdev->dev, "failed to poke device, command %d, err %d\n",
+				rep_data[0], ret);
+	return;
+}
+
+static ssize_t wacom_show_speed(struct device *dev,
+				struct device_attribute
+				*attr, char *buf)
+{
+	struct wacom_data *wdata = dev_get_drvdata(dev);
+
+	return snprintf(buf, PAGE_SIZE, "%i\n", wdata->high_speed);
+}
+
+static ssize_t wacom_store_speed(struct device *dev,
+				struct device_attribute *attr,
+				const char *buf, size_t count)
+{
+	struct hid_device *hdev = container_of(dev, struct hid_device, dev);
+	int new_speed;
+
+	if (sscanf(buf, "%1d", &new_speed ) != 1)
+		return -EINVAL;
+
+	if (new_speed == 0 || new_speed == 1) {
+		wacom_poke(hdev, new_speed);
+		return strnlen(buf, PAGE_SIZE);
+	} else
+		return -EINVAL;
+}
+
+static DEVICE_ATTR(speed, S_IRUGO | S_IWUGO,
+		wacom_show_speed, wacom_store_speed);
+
 static int wacom_raw_event(struct hid_device *hdev, struct hid_report *report,
 		u8 *raw_data, int size)
 {
@@ -148,6 +293,12 @@
 		input_sync(input);
 	}
 
+#ifdef CONFIG_HID_WACOM_POWER_SUPPLY
+	/* Store current battery capacity */
+	rw = (data[7] >> 2 & 0x07);
+	if (rw != wdata->battery_capacity)
+		wdata->battery_capacity = rw;
+#endif
 	return 1;
 }
 
@@ -157,9 +308,7 @@
 	struct hid_input *hidinput;
 	struct input_dev *input;
 	struct wacom_data *wdata;
-	char rep_data[2];
 	int ret;
-	int limit;
 
 	wdata = kzalloc(sizeof(*wdata), GFP_KERNEL);
 	if (wdata == NULL) {
@@ -182,31 +331,53 @@
 		goto err_free;
 	}
 
-	/*
-	 * Note that if the raw queries fail, it's not a hard failure and it
-	 * is safe to continue
-	 */
+	ret = device_create_file(&hdev->dev, &dev_attr_speed);
+	if (ret)
+		dev_warn(&hdev->dev,
+			"can't create sysfs speed attribute err: %d\n", ret);
 
-	/* Set Wacom mode2 */
-	rep_data[0] = 0x03; rep_data[1] = 0x00;
-	limit = 3;
-	do {
-		ret = hdev->hid_output_raw_report(hdev, rep_data, 2,
-				HID_FEATURE_REPORT);
-	} while (ret < 0 && limit-- > 0);
-	if (ret < 0)
-		dev_warn(&hdev->dev, "failed to poke device #1, %d\n", ret);
+	/* Set Wacom mode 2 with high reporting speed */
+	wacom_poke(hdev, 1);
 
-	/* 0x06 - high reporting speed, 0x05 - low speed */
-	rep_data[0] = 0x06; rep_data[1] = 0x00;
-	limit = 3;
-	do {
-		ret = hdev->hid_output_raw_report(hdev, rep_data, 2,
-				HID_FEATURE_REPORT);
-	} while (ret < 0 && limit-- > 0);
-	if (ret < 0)
-		dev_warn(&hdev->dev, "failed to poke device #2, %d\n", ret);
+#ifdef CONFIG_HID_WACOM_POWER_SUPPLY
+	wdata->battery.properties = wacom_battery_props;
+	wdata->battery.num_properties = ARRAY_SIZE(wacom_battery_props);
+	wdata->battery.get_property = wacom_battery_get_property;
+	wdata->battery.name = "wacom_battery";
+	wdata->battery.type = POWER_SUPPLY_TYPE_BATTERY;
+	wdata->battery.use_for_apm = 0;
 
+	ret = power_supply_register(&hdev->dev, &wdata->battery);
+	if (ret) {
+		dev_warn(&hdev->dev,
+			"can't create sysfs battery attribute, err: %d\n", ret);
+		/*
+		 * battery attribute is not critical for the tablet, but if it
+		 * failed then there is no need to create ac attribute
+		 */
+		goto move_on;
+	}
+
+	wdata->ac.properties = wacom_ac_props;
+	wdata->ac.num_properties = ARRAY_SIZE(wacom_ac_props);
+	wdata->ac.get_property = wacom_ac_get_property;
+	wdata->ac.name = "wacom_ac";
+	wdata->ac.type = POWER_SUPPLY_TYPE_MAINS;
+	wdata->ac.use_for_apm = 0;
+
+	ret = power_supply_register(&hdev->dev, &wdata->ac);
+	if (ret) {
+		dev_warn(&hdev->dev,
+			"can't create ac battery attribute, err: %d\n", ret);
+		/*
+		 * ac attribute is not critical for the tablet, but if it
+		 * failed then we don't want to battery attribute to exist
+		 */
+		power_supply_unregister(&wdata->battery);
+	}
+
+move_on:
+#endif
 	hidinput = list_entry(hdev->inputs.next, struct hid_input, list);
 	input = hidinput->input;
 
@@ -251,13 +422,21 @@
 
 static void wacom_remove(struct hid_device *hdev)
 {
+#ifdef CONFIG_HID_WACOM_POWER_SUPPLY
+	struct wacom_data *wdata = hid_get_drvdata(hdev);
+#endif
 	hid_hw_stop(hdev);
+
+#ifdef CONFIG_HID_WACOM_POWER_SUPPLY
+	power_supply_unregister(&wdata->battery);
+	power_supply_unregister(&wdata->ac);
+#endif
 	kfree(hid_get_drvdata(hdev));
 }
 
 static const struct hid_device_id wacom_devices[] = {
 	{ HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_WACOM, USB_DEVICE_ID_WACOM_GRAPHIRE_BLUETOOTH) },
-
+	{ HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_WACOM, USB_DEVICE_ID_WACOM_INTUOS4_BLUETOOTH) },
 	{ }
 };
 MODULE_DEVICE_TABLE(hid, wacom_devices);
diff --git a/drivers/hid/hid-zydacron.c b/drivers/hid/hid-zydacron.c
new file mode 100644
index 0000000..9e8d35a
--- /dev/null
+++ b/drivers/hid/hid-zydacron.c
@@ -0,0 +1,237 @@
+/*
+*  HID driver for zydacron remote control
+*
+*  Copyright (c) 2010 Don Prince <dhprince.devel@yahoo.co.uk>
+*/
+
+/*
+* This program is free software; you can redistribute it and/or modify it
+* under the terms of the GNU General Public License as published by the Free
+* Software Foundation; either version 2 of the License, or (at your option)
+* any later version.
+*/
+
+#include <linux/device.h>
+#include <linux/hid.h>
+#include <linux/module.h>
+
+#include "hid-ids.h"
+
+struct zc_device {
+	struct input_dev	*input_ep81;
+	unsigned short		last_key[4];
+};
+
+
+/*
+* Zydacron remote control has an invalid HID report descriptor,
+* that needs fixing before we can parse it.
+*/
+static void zc_report_fixup(struct hid_device *hdev, __u8 *rdesc,
+	unsigned int rsize)
+{
+	if (rsize >= 253 &&
+		rdesc[0x96] == 0xbc && rdesc[0x97] == 0xff &&
+		rdesc[0xca] == 0xbc && rdesc[0xcb] == 0xff &&
+		rdesc[0xe1] == 0xbc && rdesc[0xe2] == 0xff) {
+			dev_info(&hdev->dev,
+				"fixing up zydacron remote control report "
+				"descriptor\n");
+			rdesc[0x96] = rdesc[0xca] = rdesc[0xe1] = 0x0c;
+			rdesc[0x97] = rdesc[0xcb] = rdesc[0xe2] = 0x00;
+		}
+}
+
+#define zc_map_key_clear(c) \
+	hid_map_usage_clear(hi, usage, bit, max, EV_KEY, (c))
+
+static int zc_input_mapping(struct hid_device *hdev, struct hid_input *hi,
+	struct hid_field *field, struct hid_usage *usage,
+	unsigned long **bit, int *max)
+{
+	int i;
+	struct zc_device *zc = hid_get_drvdata(hdev);
+	zc->input_ep81 = hi->input;
+
+	if ((usage->hid & HID_USAGE_PAGE) != HID_UP_CONSUMER)
+		return 0;
+
+	dbg_hid("zynacron input mapping event [0x%x]\n",
+		usage->hid & HID_USAGE);
+
+	switch (usage->hid & HID_USAGE) {
+	/* report 2 */
+	case 0x10:
+		zc_map_key_clear(KEY_MODE);
+		break;
+	case 0x30:
+		zc_map_key_clear(KEY_SCREEN);
+		break;
+	case 0x70:
+		zc_map_key_clear(KEY_INFO);
+		break;
+	/* report 3 */
+	case 0x04:
+		zc_map_key_clear(KEY_RADIO);
+		break;
+	/* report 4 */
+	case 0x0d:
+		zc_map_key_clear(KEY_PVR);
+		break;
+	case 0x25:
+		zc_map_key_clear(KEY_TV);
+		break;
+	case 0x47:
+		zc_map_key_clear(KEY_AUDIO);
+		break;
+	case 0x49:
+		zc_map_key_clear(KEY_AUX);
+		break;
+	case 0x4a:
+		zc_map_key_clear(KEY_VIDEO);
+		break;
+	case 0x48:
+		zc_map_key_clear(KEY_DVD);
+		break;
+	case 0x24:
+		zc_map_key_clear(KEY_MENU);
+		break;
+	case 0x32:
+		zc_map_key_clear(KEY_TEXT);
+		break;
+	default:
+		return 0;
+	}
+
+	for (i = 0; i < 4; i++)
+		zc->last_key[i] = 0;
+
+	return 1;
+}
+
+static int zc_raw_event(struct hid_device *hdev, struct hid_report *report,
+	 u8 *data, int size)
+{
+	struct zc_device *zc = hid_get_drvdata(hdev);
+	int ret = 0;
+	unsigned key;
+	unsigned short index;
+
+	if (report->id == data[0]) {
+
+		/* break keys */
+		for (index = 0; index < 4; index++) {
+			key = zc->last_key[index];
+			if (key) {
+				input_event(zc->input_ep81, EV_KEY, key, 0);
+				zc->last_key[index] = 0;
+			}
+		}
+
+		key = 0;
+		switch (report->id) {
+		case 0x02:
+		case 0x03:
+			switch (data[1]) {
+			case 0x10:
+				key = KEY_MODE;
+				index = 0;
+				break;
+			case 0x30:
+				key = KEY_SCREEN;
+				index = 1;
+				break;
+			case 0x70:
+				key = KEY_INFO;
+				index = 2;
+				break;
+			case 0x04:
+				key = KEY_RADIO;
+				index = 3;
+				break;
+			}
+
+			if (key) {
+				input_event(zc->input_ep81, EV_KEY, key, 1);
+				zc->last_key[index] = key;
+			}
+
+			ret = 1;
+			break;
+		}
+	}
+
+	return ret;
+}
+
+static int zc_probe(struct hid_device *hdev, const struct hid_device_id *id)
+{
+	int ret;
+	struct zc_device *zc;
+
+	zc = kzalloc(sizeof(*zc), GFP_KERNEL);
+	if (zc == NULL) {
+		dev_err(&hdev->dev, "zydacron: can't alloc descriptor\n");
+		return -ENOMEM;
+	}
+
+	hid_set_drvdata(hdev, zc);
+
+	ret = hid_parse(hdev);
+	if (ret) {
+		dev_err(&hdev->dev, "zydacron: parse failed\n");
+		goto err_free;
+	}
+
+	ret = hid_hw_start(hdev, HID_CONNECT_DEFAULT);
+	if (ret) {
+		dev_err(&hdev->dev, "zydacron: hw start failed\n");
+		goto err_free;
+	}
+
+	return 0;
+err_free:
+	kfree(zc);
+
+	return ret;
+}
+
+static void zc_remove(struct hid_device *hdev)
+{
+	struct zc_device *zc = hid_get_drvdata(hdev);
+
+	hid_hw_stop(hdev);
+
+	if (NULL != zc)
+		kfree(zc);
+}
+
+static const struct hid_device_id zc_devices[] = {
+	{ HID_USB_DEVICE(USB_VENDOR_ID_ZYDACRON, USB_DEVICE_ID_ZYDACRON_REMOTE_CONTROL) },
+	{ }
+};
+MODULE_DEVICE_TABLE(hid, zc_devices);
+
+static struct hid_driver zc_driver = {
+	.name = "zydacron",
+	.id_table = zc_devices,
+	.report_fixup = zc_report_fixup,
+	.input_mapping = zc_input_mapping,
+	.raw_event = zc_raw_event,
+	.probe = zc_probe,
+	.remove = zc_remove,
+};
+
+static int __init zc_init(void)
+{
+	return hid_register_driver(&zc_driver);
+}
+
+static void __exit zc_exit(void)
+{
+	hid_unregister_driver(&zc_driver);
+}
+
+module_init(zc_init);
+module_exit(zc_exit);
+MODULE_LICENSE("GPL");
diff --git a/drivers/hid/hidraw.c b/drivers/hid/hidraw.c
index 6eadf1a..3ccd478 100644
--- a/drivers/hid/hidraw.c
+++ b/drivers/hid/hidraw.c
@@ -106,38 +106,48 @@
 static ssize_t hidraw_write(struct file *file, const char __user *buffer, size_t count, loff_t *ppos)
 {
 	unsigned int minor = iminor(file->f_path.dentry->d_inode);
-	/* FIXME: What stops hidraw_table going NULL */
-	struct hid_device *dev = hidraw_table[minor]->hid;
+	struct hid_device *dev;
 	__u8 *buf;
 	int ret = 0;
 
-	if (!dev->hid_output_raw_report)
-		return -ENODEV;
+	mutex_lock(&minors_lock);
+	dev = hidraw_table[minor]->hid;
+
+	if (!dev->hid_output_raw_report) {
+		ret = -ENODEV;
+		goto out;
+	}
 
 	if (count > HID_MAX_BUFFER_SIZE) {
 		printk(KERN_WARNING "hidraw: pid %d passed too large report\n",
 				task_pid_nr(current));
-		return -EINVAL;
+		ret = -EINVAL;
+		goto out;
 	}
 
 	if (count < 2) {
 		printk(KERN_WARNING "hidraw: pid %d passed too short report\n",
 				task_pid_nr(current));
-		return -EINVAL;
-	}
-
-	buf = kmalloc(count * sizeof(__u8), GFP_KERNEL);
-	if (!buf)
-		return -ENOMEM;
-
-	if (copy_from_user(buf, buffer, count)) {
-		ret = -EFAULT;
+		ret = -EINVAL;
 		goto out;
 	}
 
+	buf = kmalloc(count * sizeof(__u8), GFP_KERNEL);
+	if (!buf) {
+		ret = -ENOMEM;
+		goto out;
+	}
+
+	if (copy_from_user(buf, buffer, count)) {
+		ret = -EFAULT;
+		goto out_free;
+	}
+
 	ret = dev->hid_output_raw_report(dev, buf, count, HID_OUTPUT_REPORT);
-out:
+out_free:
 	kfree(buf);
+out:
+	mutex_unlock(&minors_lock);
 	return ret;
 }
 
@@ -165,11 +175,8 @@
 		goto out;
 	}
 
-	lock_kernel();
 	mutex_lock(&minors_lock);
 	if (!hidraw_table[minor]) {
-		printk(KERN_EMERG "hidraw device with minor %d doesn't exist\n",
-				minor);
 		kfree(list);
 		err = -ENODEV;
 		goto out_unlock;
@@ -197,7 +204,6 @@
 
 out_unlock:
 	mutex_unlock(&minors_lock);
-	unlock_kernel();
 out:
 	return err;
 
@@ -209,11 +215,8 @@
 	struct hidraw *dev;
 	struct hidraw_list *list = file->private_data;
 
-	if (!hidraw_table[minor]) {
-		printk(KERN_EMERG "hidraw device with minor %d doesn't exist\n",
-				minor);
+	if (!hidraw_table[minor])
 		return -ENODEV;
-	}
 
 	list_del(&list->node);
 	dev = hidraw_table[minor];
@@ -238,11 +241,12 @@
 	struct inode *inode = file->f_path.dentry->d_inode;
 	unsigned int minor = iminor(inode);
 	long ret = 0;
-	/* FIXME: What stops hidraw_table going NULL */
-	struct hidraw *dev = hidraw_table[minor];
+	struct hidraw *dev;
 	void __user *user_arg = (void __user*) arg;
 
-	lock_kernel();
+	mutex_lock(&minors_lock);
+	dev = hidraw_table[minor];
+
 	switch (cmd) {
 		case HIDIOCGRDESCSIZE:
 			if (put_user(dev->hid->rsize, (int __user *)arg))
@@ -311,11 +315,11 @@
 						-EFAULT : len;
 					break;
 				}
-                }
+		}
 
 		ret = -ENOTTY;
 	}
-	unlock_kernel();
+	mutex_unlock(&minors_lock);
 	return ret;
 }
 
diff --git a/drivers/hid/usbhid/hid-core.c b/drivers/hid/usbhid/hid-core.c
index df61975..1ebd324 100644
--- a/drivers/hid/usbhid/hid-core.c
+++ b/drivers/hid/usbhid/hid-core.c
@@ -623,6 +623,7 @@
 
 	return 0;
 }
+EXPORT_SYMBOL_GPL(usbhid_wait_io);
 
 static int hid_set_idle(struct usb_device *dev, int ifnum, int report, int idle)
 {
@@ -806,16 +807,36 @@
 	struct usb_host_interface *interface = intf->cur_altsetting;
 	int ret;
 
-	ret = usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
-		HID_REQ_SET_REPORT,
-		USB_DIR_OUT | USB_TYPE_CLASS | USB_RECIP_INTERFACE,
-		((report_type + 1) << 8) | *buf,
-		interface->desc.bInterfaceNumber, buf + 1, count - 1,
-		USB_CTRL_SET_TIMEOUT);
-
-	/* count also the report id */
-	if (ret > 0)
-		ret++;
+	if (usbhid->urbout) {
+		int actual_length;
+		int skipped_report_id = 0;
+		if (buf[0] == 0x0) {
+			/* Don't send the Report ID */
+			buf++;
+			count--;
+			skipped_report_id = 1;
+		}
+		ret = usb_interrupt_msg(dev, usbhid->urbout->pipe,
+			buf, count, &actual_length,
+			USB_CTRL_SET_TIMEOUT);
+		/* return the number of bytes transferred */
+		if (ret == 0) {
+			ret = actual_length;
+			/* count also the report id */
+			if (skipped_report_id)
+				ret++;
+		}
+	} else {
+		ret = usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
+			HID_REQ_SET_REPORT,
+			USB_DIR_OUT | USB_TYPE_CLASS | USB_RECIP_INTERFACE,
+			((report_type + 1) << 8) | *buf,
+			interface->desc.bInterfaceNumber, buf + 1, count - 1,
+			USB_CTRL_SET_TIMEOUT);
+		/* count also the report id */
+		if (ret > 0)
+			ret++;
+	}
 
 	return ret;
 }
@@ -1017,12 +1038,15 @@
 	/* Some keyboards don't work until their LEDs have been set.
 	 * Since BIOSes do set the LEDs, it must be safe for any device
 	 * that supports the keyboard boot protocol.
+	 * In addition, enable remote wakeup by default for all keyboard
+	 * devices supporting the boot protocol.
 	 */
 	if (interface->desc.bInterfaceSubClass == USB_INTERFACE_SUBCLASS_BOOT &&
 			interface->desc.bInterfaceProtocol ==
-				USB_INTERFACE_PROTOCOL_KEYBOARD)
+				USB_INTERFACE_PROTOCOL_KEYBOARD) {
 		usbhid_set_leds(hid);
-
+		device_set_wakeup_enable(&dev->dev, 1);
+	}
 	return 0;
 
 fail:
@@ -1131,6 +1155,7 @@
 	hid->vendor = le16_to_cpu(dev->descriptor.idVendor);
 	hid->product = le16_to_cpu(dev->descriptor.idProduct);
 	hid->name[0] = 0;
+	hid->quirks = usbhid_lookup_quirk(hid->vendor, hid->product);
 	if (intf->cur_altsetting->desc.bInterfaceProtocol ==
 			USB_INTERFACE_PROTOCOL_MOUSE)
 		hid->type = HID_TYPE_USBMOUSE;
@@ -1287,6 +1312,11 @@
 		{
 			set_bit(HID_REPORTED_IDLE, &usbhid->iofl);
 			spin_unlock_irq(&usbhid->lock);
+			if (hid->driver && hid->driver->suspend) {
+				status = hid->driver->suspend(hid, message);
+				if (status < 0)
+					return status;
+			}
 		} else {
 			usbhid_mark_busy(usbhid);
 			spin_unlock_irq(&usbhid->lock);
@@ -1294,6 +1324,11 @@
 		}
 
 	} else {
+		if (hid->driver && hid->driver->suspend) {
+			status = hid->driver->suspend(hid, message);
+			if (status < 0)
+				return status;
+		}
 		spin_lock_irq(&usbhid->lock);
 		set_bit(HID_REPORTED_IDLE, &usbhid->iofl);
 		spin_unlock_irq(&usbhid->lock);
@@ -1348,6 +1383,11 @@
 		hid_io_error(hid);
 	usbhid_restart_queues(usbhid);
 
+	if (status >= 0 && hid->driver && hid->driver->resume) {
+		int ret = hid->driver->resume(hid);
+		if (ret < 0)
+			status = ret;
+	}
 	dev_dbg(&intf->dev, "resume status %d\n", status);
 	return 0;
 }
@@ -1356,9 +1396,16 @@
 {
 	struct hid_device *hid = usb_get_intfdata(intf);
 	struct usbhid_device *usbhid = hid->driver_data;
+	int status;
 
 	clear_bit(HID_REPORTED_IDLE, &usbhid->iofl);
-	return hid_post_reset(intf);
+	status = hid_post_reset(intf);
+	if (status >= 0 && hid->driver && hid->driver->reset_resume) {
+		int ret = hid->driver->reset_resume(hid);
+		if (ret < 0)
+			status = ret;
+	}
+	return status;
 }
 
 #endif /* CONFIG_PM */
diff --git a/drivers/hid/usbhid/hid-quirks.c b/drivers/hid/usbhid/hid-quirks.c
index 1152f9b..5ff8d32 100644
--- a/drivers/hid/usbhid/hid-quirks.c
+++ b/drivers/hid/usbhid/hid-quirks.c
@@ -33,6 +33,7 @@
 	{ USB_VENDOR_ID_AASHIMA, USB_DEVICE_ID_AASHIMA_PREDATOR, HID_QUIRK_BADPAD },
 	{ USB_VENDOR_ID_ALPS, USB_DEVICE_ID_IBM_GAMEPAD, HID_QUIRK_BADPAD },
 	{ USB_VENDOR_ID_CHIC, USB_DEVICE_ID_CHIC_GAMEPAD, HID_QUIRK_BADPAD },
+	{ USB_VENDOR_ID_DWAV, USB_DEVICE_ID_DWAV_EGALAX_MULTITOUCH, HID_QUIRK_MULTI_INPUT },
 	{ USB_VENDOR_ID_HAPP, USB_DEVICE_ID_UGCI_DRIVING, HID_QUIRK_BADPAD | HID_QUIRK_MULTI_INPUT },
 	{ USB_VENDOR_ID_HAPP, USB_DEVICE_ID_UGCI_FLYING, HID_QUIRK_BADPAD | HID_QUIRK_MULTI_INPUT },
 	{ USB_VENDOR_ID_HAPP, USB_DEVICE_ID_UGCI_FIGHTING, HID_QUIRK_BADPAD | HID_QUIRK_MULTI_INPUT },
diff --git a/drivers/hid/usbhid/hiddev.c b/drivers/hid/usbhid/hiddev.c
index 433602a..c24d2fa 100644
--- a/drivers/hid/usbhid/hiddev.c
+++ b/drivers/hid/usbhid/hiddev.c
@@ -267,6 +267,7 @@
 	struct hiddev_list *list;
 	int res, i;
 
+	/* See comment in hiddev_connect() for BKL explanation */
 	lock_kernel();
 	i = iminor(inode) - HIDDEV_MINOR_BASE;
 
@@ -894,8 +895,22 @@
 	hiddev->hid = hid;
 	hiddev->exist = 1;
 
-	/* when lock_kernel() usage is fixed in usb_open(),
-	 * we could also fix it here */
+	/*
+	 * BKL here is used to avoid race after usb_register_dev().
+	 * Once the device node has been created, open() could happen on it.
+	 * The code below will then fail, as hiddev_table hasn't been
+	 * updated.
+	 *
+	 * The obvious fix -- introducing mutex to guard hiddev_table[]
+	 * doesn't work, as usb_open() and usb_register_dev() both take
+	 * minor_rwsem, thus we'll have ABBA deadlock.
+	 *
+	 * Before BKL pushdown, usb_open() had been acquiring it in right
+	 * order, so _open() was safe to use it to protect from this race.
+	 * Now the order is different, but AB-BA deadlock still doesn't occur
+	 * as BKL is dropped on schedule() (i.e. while sleeping on
+	 * minor_rwsem). Fugly.
+	 */
 	lock_kernel();
 	retval = usb_register_dev(usbhid->intf, &hiddev_class);
 	if (retval) {
diff --git a/drivers/hid/usbhid/usbkbd.c b/drivers/hid/usbhid/usbkbd.c
index bb14c82..a948605 100644
--- a/drivers/hid/usbhid/usbkbd.c
+++ b/drivers/hid/usbhid/usbkbd.c
@@ -311,6 +311,7 @@
 		goto fail2;
 
 	usb_set_intfdata(iface, kbd);
+	device_set_wakeup_enable(&dev->dev, 1);
 	return 0;
 
 fail2:	
diff --git a/include/linux/hid.h b/include/linux/hid.h
index b1344ec..895001f 100644
--- a/include/linux/hid.h
+++ b/include/linux/hid.h
@@ -308,11 +308,13 @@
 #define HID_QUIRK_NOTOUCH			0x00000002
 #define HID_QUIRK_IGNORE			0x00000004
 #define HID_QUIRK_NOGET				0x00000008
+#define HID_QUIRK_HIDDEV_FORCE			0x00000010
 #define HID_QUIRK_BADPAD			0x00000020
 #define HID_QUIRK_MULTI_INPUT			0x00000040
 #define HID_QUIRK_SKIP_OUTPUT_REPORTS		0x00010000
 #define HID_QUIRK_FULLSPEED_INTERVAL		0x10000000
 #define HID_QUIRK_NO_INIT_REPORTS		0x20000000
+#define HID_QUIRK_NO_IGNORE			0x40000000
 
 /*
  * This is the global environment of the parser. This information is
@@ -589,6 +591,9 @@
  * @report_fixup: called before report descriptor parsing (NULL means nop)
  * @input_mapping: invoked on input registering before mapping an usage
  * @input_mapped: invoked on input registering after mapping an usage
+ * @suspend: invoked on suspend (NULL means nop)
+ * @resume: invoked on resume if device was not reset (NULL means nop)
+ * @reset_resume: invoked on resume if device was reset (NULL means nop)
  *
  * raw_event and event should return 0 on no action performed, 1 when no
  * further processing should be done and negative on error
@@ -629,6 +634,11 @@
 	int (*input_mapped)(struct hid_device *hdev,
 			struct hid_input *hidinput, struct hid_field *field,
 			struct hid_usage *usage, unsigned long **bit, int *max);
+#ifdef CONFIG_PM
+	int (*suspend)(struct hid_device *hdev, pm_message_t message);
+	int (*resume)(struct hid_device *hdev);
+	int (*reset_resume)(struct hid_device *hdev);
+#endif
 /* private: */
 	struct device_driver driver;
 };