diff --git a/drivers/net/ne2.c b/drivers/net/ne2.c
index eebf5f0..5fccfea 100644
--- a/drivers/net/ne2.c
+++ b/drivers/net/ne2.c
@@ -28,7 +28,7 @@
    - added support for Arco Electronics AE/2-card (experimental)
 
    Mon Sep 14 09:53:42 CET 1998 (David Weinehall)
-   - added support for Compex ENET-16MC/P (experimental) 
+   - added support for Compex ENET-16MC/P (experimental)
 
    Tue Sep 15 16:21:12 CET 1998 (David Weinehall, Magnus Jonsson, Tomas Ogren)
    - Miscellaneous bugfixes
@@ -44,11 +44,11 @@
    - Version# bump
 
    Mon Nov 16 15:28:23 CET 1998 (Wim Dumon)
-   - pass 'dev' as last parameter of request_irq in stead of 'NULL'   
+   - pass 'dev' as last parameter of request_irq in stead of 'NULL'
 
    Wed Feb  7 21:24:00 CET 2001 (Alfred Arnold)
    - added support for the D-Link DE-320CT
-   
+
    *    WARNING
 	-------
 	This is alpha-test software.  It is not guaranteed to work. As a
@@ -150,9 +150,9 @@
 
 
 /*
- * special code to read the DE-320's MAC address EEPROM.  In contrast to a 
+ * special code to read the DE-320's MAC address EEPROM.  In contrast to a
  * standard NE design, this is a serial EEPROM (93C46) that has to be read
- * bit by bit.  The EEPROM cotrol port at base + 0x1e has the following 
+ * bit by bit.  The EEPROM cotrol port at base + 0x1e has the following
  * layout:
  *
  * Bit 0 = Data out (read from EEPROM)
@@ -218,7 +218,7 @@
 {
 	int z;
 	unsigned int value = 0;
- 
+
 	/* pull the CS line low for a moment.  This resets the EEPROM-
 	   internal logic, and makes it ready for a new command. */
 
@@ -253,23 +253,23 @@
 
 	SET_MODULE_OWNER(dev);
 
-	/* Do not check any supplied i/o locations. 
+	/* Do not check any supplied i/o locations.
 	   POS registers usually don't fail :) */
 
-	/* MCA cards have POS registers.  
-	   Autodetecting MCA cards is extremely simple. 
+	/* MCA cards have POS registers.
+	   Autodetecting MCA cards is extremely simple.
 	   Just search for the card. */
 
 	for(i = 0; (ne2_adapters[i].name != NULL) && !adapter_found; i++) {
-		current_mca_slot = 
+		current_mca_slot =
 			mca_find_unused_adapter(ne2_adapters[i].id, 0);
 
 		if((current_mca_slot != MCA_NOTFOUND) && !adapter_found) {
 			int res;
-			mca_set_adapter_name(current_mca_slot, 
+			mca_set_adapter_name(current_mca_slot,
 					ne2_adapters[i].name);
 			mca_mark_as_used(current_mca_slot);
-			
+
 			res = ne2_probe1(dev, current_mca_slot);
 			if (res)
 				mca_mark_as_unused(current_mca_slot);
@@ -307,7 +307,7 @@
 
 	len += sprintf(buf+len, "The NE/2 Ethernet Adapter\n" );
 	len += sprintf(buf+len, "Driver written by Wim Dumon ");
-	len += sprintf(buf+len, "<wimpie@kotnet.org>\n"); 
+	len += sprintf(buf+len, "<wimpie@kotnet.org>\n");
 	len += sprintf(buf+len, "Modified by ");
 	len += sprintf(buf+len, "David Weinehall <tao@acc.umu.se>\n");
 	len += sprintf(buf+len, "and by Magnus Jonsson <bigfoot@acc.umu.se>\n");
@@ -316,8 +316,8 @@
 	len += sprintf(buf+len, "IRQ    : %d\n", dev->irq);
 
 #define HW_ADDR(i) dev->dev_addr[i]
-	len += sprintf(buf+len, "HW addr : %x:%x:%x:%x:%x:%x\n", 
-			HW_ADDR(0), HW_ADDR(1), HW_ADDR(2), 
+	len += sprintf(buf+len, "HW addr : %x:%x:%x:%x:%x:%x\n",
+			HW_ADDR(0), HW_ADDR(1), HW_ADDR(2),
 			HW_ADDR(3), HW_ADDR(4), HW_ADDR(5) );
 #undef HW_ADDR
 
@@ -370,7 +370,7 @@
 
 #ifndef CRYNWR_WAY
 	/* Reset the card the way they do it in the Crynwr packet driver */
-	for (i=0; i<8; i++) 
+	for (i=0; i<8; i++)
 		outb(0x0, base_addr + NE_RESET);
 	inb(base_addr + NE_RESET);
 	outb(0x21, base_addr + NE_CMD);
@@ -388,10 +388,10 @@
 
 #else  /* _I_ never tested it this way .. Go ahead and try ...*/
 	/* Reset card. Who knows what dain-bramaged state it was left in. */
-	{ 
+	{
 		unsigned long reset_start_time = jiffies;
 
-		/* DON'T change these to inb_p/outb_p or reset will fail on 
+		/* DON'T change these to inb_p/outb_p or reset will fail on
 		   clones.. */
 		outb(inb(base_addr + NE_RESET), base_addr + NE_RESET);
 
@@ -408,16 +408,16 @@
 
 
 	/* Read the 16 bytes of station address PROM.
-	   We must first initialize registers, similar to 
+	   We must first initialize registers, similar to
 	   NS8390_init(eifdev, 0).
 	   We can't reliably read the SAPROM address without this.
 	   (I learned the hard way!). */
 	{
-		struct { 
-			unsigned char value, offset; 
+		struct {
+			unsigned char value, offset;
 		} program_seq[] = {
 						/* Select page 0 */
-			{E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD}, 
+			{E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD},
 			{0x49,	EN0_DCFG},  /* Set WORD-wide (0x49) access. */
 			{0x00,	EN0_RCNTLO},  /* Clear the count regs. */
 			{0x00,	EN0_RCNTHI},
@@ -433,7 +433,7 @@
 		};
 
 		for (i = 0; i < sizeof(program_seq)/sizeof(program_seq[0]); i++)
-			outb_p(program_seq[i].value, base_addr + 
+			outb_p(program_seq[i].value, base_addr +
 				program_seq[i].offset);
 
 	}
@@ -464,7 +464,7 @@
 	   share and the board will usually be enabled. */
 	retval = request_irq(dev->irq, ei_interrupt, 0, DRV_NAME, dev);
 	if (retval) {
-		printk (" unable to get IRQ %d (irqval=%d).\n", 
+		printk (" unable to get IRQ %d (irqval=%d).\n",
 				dev->irq, retval);
 		goto out;
 	}
@@ -496,9 +496,9 @@
 	ei_status.block_input = &ne_block_input;
 	ei_status.block_output = &ne_block_output;
 	ei_status.get_8390_hdr = &ne_get_8390_hdr;
-	
+
 	ei_status.priv = slot;
-	
+
 	dev->open = &ne_open;
 	dev->stop = &ne_close;
 #ifdef CONFIG_NET_POLL_CONTROLLER
@@ -538,7 +538,7 @@
 {
 	unsigned long reset_start_time = jiffies;
 
-	if (ei_debug > 1) 
+	if (ei_debug > 1)
 		printk("resetting the 8390 t=%ld...", jiffies);
 
 	/* DON'T change these to inb_p/outb_p or reset will fail on clones. */
@@ -550,7 +550,7 @@
 	/* This check _should_not_ be necessary, omit eventually. */
 	while ((inb_p(NE_BASE+EN0_ISR) & ENISR_RESET) == 0)
 		if (time_after(jiffies, reset_start_time + 2*HZ/100)) {
-			printk("%s: ne_reset_8390() did not complete.\n", 
+			printk("%s: ne_reset_8390() did not complete.\n",
 					dev->name);
 			break;
 		}
@@ -561,13 +561,13 @@
    we don't need to be concerned with ring wrap as the header will be at
    the start of a page, so we optimize accordingly. */
 
-static void ne_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr, 
+static void ne_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr,
 		int ring_page)
 {
 
 	int nic_base = dev->base_addr;
 
-	/* This *shouldn't* happen. 
+	/* This *shouldn't* happen.
 	   If it does, it's the last thing you'll see */
 	if (ei_status.dmaing) {
 		printk("%s: DMAing conflict in ne_get_8390_hdr "
@@ -585,10 +585,10 @@
 	outb_p(E8390_RREAD+E8390_START, nic_base + NE_CMD);
 
 	if (ei_status.word16)
-		insw(NE_BASE + NE_DATAPORT, hdr, 
+		insw(NE_BASE + NE_DATAPORT, hdr,
 				sizeof(struct e8390_pkt_hdr)>>1);
 	else
-		insb(NE_BASE + NE_DATAPORT, hdr, 
+		insb(NE_BASE + NE_DATAPORT, hdr,
 				sizeof(struct e8390_pkt_hdr));
 
 	outb_p(ENISR_RDC, nic_base + EN0_ISR);	/* Ack intr. */
@@ -600,7 +600,7 @@
    hints. The NEx000 doesn't share the on-board packet memory -- you have
    to put the packet out through the "remote DMA" dataport using outb. */
 
-static void ne_block_input(struct net_device *dev, int count, struct sk_buff *skb, 
+static void ne_block_input(struct net_device *dev, int count, struct sk_buff *skb,
 		int ring_offset)
 {
 #ifdef NE_SANITY_CHECK
@@ -609,7 +609,7 @@
 	int nic_base = dev->base_addr;
 	char *buf = skb->data;
 
-	/* This *shouldn't* happen. 
+	/* This *shouldn't* happen.
 	   If it does, it's the last thing you'll see */
 	if (ei_status.dmaing) {
 		printk("%s: DMAing conflict in ne_block_input "
@@ -677,7 +677,7 @@
 	if (ei_status.word16 && (count & 0x01))
 		count++;
 
-	/* This *shouldn't* happen. 
+	/* This *shouldn't* happen.
 	   If it does, it's the last thing you'll see */
 	if (ei_status.dmaing) {
 		printk("%s: DMAing conflict in ne_block_output."