[PATCH] sky2: support msi interrupt (revised)
This hardware supports Message Signaled interrupts.
When setting up, use software interrupt to check for bad hardware.
Signed-off-by: Stephen Hemminger <shemminger @osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c
index 62733a6..8ed4bd1 100644
--- a/drivers/net/sky2.c
+++ b/drivers/net/sky2.c
@@ -101,6 +101,10 @@
module_param(copybreak, int, 0);
MODULE_PARM_DESC(copybreak, "Receive copy threshold");
+static int disable_msi = 0;
+module_param(disable_msi, int, 0);
+MODULE_PARM_DESC(disable_msi, "Disable Message Signaled Interrupt (MSI)");
+
static const struct pci_device_id sky2_id_table[] = {
{ PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9000) },
{ PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9E00) },
@@ -3064,6 +3068,61 @@
dev->dev_addr[3], dev->dev_addr[4], dev->dev_addr[5]);
}
+/* Handle software interrupt used during MSI test */
+static irqreturn_t __devinit sky2_test_intr(int irq, void *dev_id,
+ struct pt_regs *regs)
+{
+ struct sky2_hw *hw = dev_id;
+ u32 status = sky2_read32(hw, B0_Y2_SP_ISRC2);
+
+ if (status == 0)
+ return IRQ_NONE;
+
+ if (status & Y2_IS_IRQ_SW) {
+ sky2_write8(hw, B0_CTST, CS_CL_SW_IRQ);
+ hw->msi = 1;
+ }
+ sky2_write32(hw, B0_Y2_SP_ICR, 2);
+
+ sky2_read32(hw, B0_IMSK);
+ return IRQ_HANDLED;
+}
+
+/* Test interrupt path by forcing a a software IRQ */
+static int __devinit sky2_test_msi(struct sky2_hw *hw)
+{
+ struct pci_dev *pdev = hw->pdev;
+ int i, err;
+
+ sky2_write32(hw, B0_IMSK, Y2_IS_IRQ_SW);
+
+ err = request_irq(pdev->irq, sky2_test_intr, SA_SHIRQ, DRV_NAME, hw);
+ if (err) {
+ printk(KERN_ERR PFX "%s: cannot assign irq %d\n",
+ pci_name(pdev), pdev->irq);
+ return err;
+ }
+
+ sky2_write8(hw, B0_CTST, CS_ST_SW_IRQ);
+ wmb();
+
+ for (i = 0; i < 10; i++) {
+ barrier();
+ if (hw->msi)
+ goto found;
+ mdelay(1);
+ }
+
+ err = -EOPNOTSUPP;
+ sky2_write8(hw, B0_CTST, CS_CL_SW_IRQ);
+ found:
+ sky2_write32(hw, B0_IMSK, 0);
+
+ free_irq(pdev->irq, hw);
+
+ return err;
+}
+
static int __devinit sky2_probe(struct pci_dev *pdev,
const struct pci_device_id *ent)
{
@@ -3184,6 +3243,20 @@
}
}
+ if (!disable_msi && pci_enable_msi(pdev) == 0) {
+ err = sky2_test_msi(hw);
+ if (err == -EOPNOTSUPP) {
+ /* MSI test failed, go back to INTx mode */
+ printk(KERN_WARNING PFX "%s: No interrupt was generated using MSI, "
+ "switching to INTx mode. Please report this failure to "
+ "the PCI maintainer and include system chipset information.\n",
+ pci_name(pdev));
+ pci_disable_msi(pdev);
+ }
+ else if (err)
+ goto err_out_unregister;
+ }
+
err = request_irq(pdev->irq, sky2_intr, SA_SHIRQ | SA_SAMPLE_RANDOM,
DRV_NAME, hw);
if (err) {
@@ -3200,6 +3273,8 @@
return 0;
err_out_unregister:
+ if (hw->msi)
+ pci_disable_msi(pdev);
if (dev1) {
unregister_netdev(dev1);
free_netdev(dev1);
@@ -3242,6 +3317,8 @@
sky2_read8(hw, B0_CTST);
free_irq(pdev->irq, hw);
+ if (hw->msi)
+ pci_disable_msi(pdev);
pci_free_consistent(pdev, STATUS_LE_BYTES, hw->st_le, hw->st_dma);
pci_release_regions(pdev);
pci_disable_device(pdev);
diff --git a/drivers/net/sky2.h b/drivers/net/sky2.h
index 70525ac..fd12c28 100644
--- a/drivers/net/sky2.h
+++ b/drivers/net/sky2.h
@@ -1841,6 +1841,7 @@
struct net_device *dev[2];
int pm_cap;
+ int msi;
u8 chip_id;
u8 chip_rev;
u8 copper;