diff --git a/arch/powerpc/Kconfig.debug b/arch/powerpc/Kconfig.debug
index 8d48e9e..c69006a 100644
--- a/arch/powerpc/Kconfig.debug
+++ b/arch/powerpc/Kconfig.debug
@@ -110,13 +110,16 @@
 	depends on 4xx || LOPEC || MV64X60 || PPLUS || PRPMC800 || \
 		PPC_GEN550 || PPC_MPC52xx
 
+config PPC_EARLY_DEBUG
+	bool "Early debugging (dangerous)"
+
 choice
-	prompt "Early debugging (dangerous)"
-	bool
-	optional
+	prompt "Early debugging console"
+	depends on PPC_EARLY_DEBUG
 	help
-	  Enable early debugging. Careful, if you enable debugging for the
-	  wrong type of machine your kernel _will not boot_.
+	  Use the selected console for early debugging. Careful, if you
+	  enable debugging for the wrong type of machine your kernel
+	  _will not boot_.
 
 config PPC_EARLY_DEBUG_LPAR
 	bool "LPAR HV Console"
diff --git a/arch/powerpc/configs/mpc85xx_cds_defconfig b/arch/powerpc/configs/mpc85xx_cds_defconfig
new file mode 100644
index 0000000..9bb022a
--- /dev/null
+++ b/arch/powerpc/configs/mpc85xx_cds_defconfig
@@ -0,0 +1,846 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.16
+# Sun Apr  2 11:23:42 2006
+#
+# CONFIG_PPC64 is not set
+CONFIG_PPC32=y
+CONFIG_PPC_MERGE=y
+CONFIG_MMU=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_PPC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+CONFIG_PPC_UDBG_16550=y
+# CONFIG_GENERIC_TBSYNC is not set
+# CONFIG_DEFAULT_UIMAGE is not set
+
+#
+# Processor support
+#
+# CONFIG_CLASSIC32 is not set
+# CONFIG_PPC_52xx is not set
+# CONFIG_PPC_82xx is not set
+# CONFIG_PPC_83xx is not set
+CONFIG_PPC_85xx=y
+# CONFIG_40x is not set
+# CONFIG_44x is not set
+# CONFIG_8xx is not set
+# CONFIG_E200 is not set
+CONFIG_85xx=y
+CONFIG_E500=y
+CONFIG_BOOKE=y
+CONFIG_FSL_BOOKE=y
+# CONFIG_PHYS_64BIT is not set
+CONFIG_SPE=y
+
+#
+# Code maturity level options
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+
+#
+# General setup
+#
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+CONFIG_SYSCTL=y
+# CONFIG_AUDIT is not set
+# CONFIG_IKCONFIG is not set
+# CONFIG_RELAY is not set
+CONFIG_INITRAMFS_SOURCE=""
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_EMBEDDED=y
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+CONFIG_SHMEM=y
+CONFIG_SLAB=y
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+# CONFIG_SLOB is not set
+
+#
+# Loadable module support
+#
+# CONFIG_MODULES is not set
+
+#
+# Block layer
+#
+# CONFIG_LBD is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+CONFIG_MPIC=y
+# CONFIG_WANT_EARLY_SERIAL is not set
+
+#
+# Platform support
+#
+# CONFIG_MPC8540_ADS is not set
+CONFIG_MPC85xx_CDS=y
+CONFIG_MPC8540=y
+CONFIG_PPC_INDIRECT_PCI_BE=y
+
+#
+# Kernel options
+#
+# CONFIG_HIGHMEM is not set
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=250
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_BINFMT_ELF=y
+CONFIG_BINFMT_MISC=y
+CONFIG_MATH_EMULATION=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+CONFIG_PROC_DEVICETREE=y
+# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_PM is not set
+# CONFIG_SOFTWARE_SUSPEND is not set
+# CONFIG_SECCOMP is not set
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+CONFIG_PPC_I8259=y
+CONFIG_PPC_INDIRECT_PCI=y
+CONFIG_FSL_SOC=y
+CONFIG_PCI=y
+CONFIG_PCI_DOMAINS=y
+# CONFIG_PCI_DEBUG is not set
+
+#
+# PCCARD (PCMCIA/CardBus) support
+#
+# CONFIG_PCCARD is not set
+
+#
+# PCI Hotplug Support
+#
+# CONFIG_HOTPLUG_PCI is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0x80000000
+CONFIG_BOOT_LOAD=0x00800000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+# CONFIG_NETDEBUG is not set
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_BIC=y
+# CONFIG_IPV6 is not set
+# CONFIG_INET6_XFRM_TUNNEL is not set
+# CONFIG_INET6_TUNNEL is not set
+# CONFIG_NETFILTER is not set
+
+#
+# DCCP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_DCCP is not set
+
+#
+# SCTP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_SCTP is not set
+
+#
+# TIPC Configuration (EXPERIMENTAL)
+#
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_NET_DIVERT is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+
+#
+# QoS and/or fair queueing
+#
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_IEEE80211 is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_DEBUG_DRIVER is not set
+
+#
+# Connector - unified userspace <-> kernelspace linker
+#
+# CONFIG_CONNECTOR is not set
+
+#
+# Memory Technology Devices (MTD)
+#
+# CONFIG_MTD is not set
+
+#
+# Parallel port support
+#
+# CONFIG_PARPORT is not set
+
+#
+# Plug and Play support
+#
+
+#
+# Block devices
+#
+# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_CPQ_DA is not set
+# CONFIG_BLK_CPQ_CISS_DA is not set
+# CONFIG_BLK_DEV_DAC960 is not set
+# CONFIG_BLK_DEV_UMEM is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=y
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_SX8 is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=32768
+CONFIG_BLK_DEV_INITRD=y
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+
+#
+# ATA/ATAPI/MFM/RLL support
+#
+CONFIG_IDE=y
+CONFIG_BLK_DEV_IDE=y
+
+#
+# Please see Documentation/ide.txt for help/info on IDE drives
+#
+# CONFIG_BLK_DEV_IDE_SATA is not set
+# CONFIG_BLK_DEV_IDEDISK is not set
+# CONFIG_IDEDISK_MULTI_MODE is not set
+# CONFIG_BLK_DEV_IDECD is not set
+# CONFIG_BLK_DEV_IDETAPE is not set
+# CONFIG_BLK_DEV_IDEFLOPPY is not set
+# CONFIG_IDE_TASK_IOCTL is not set
+
+#
+# IDE chipset support/bugfixes
+#
+CONFIG_IDE_GENERIC=y
+CONFIG_BLK_DEV_IDEPCI=y
+CONFIG_IDEPCI_SHARE_IRQ=y
+# CONFIG_BLK_DEV_OFFBOARD is not set
+CONFIG_BLK_DEV_GENERIC=y
+# CONFIG_BLK_DEV_OPTI621 is not set
+# CONFIG_BLK_DEV_SL82C105 is not set
+CONFIG_BLK_DEV_IDEDMA_PCI=y
+# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
+# CONFIG_IDEDMA_PCI_AUTO is not set
+# CONFIG_BLK_DEV_AEC62XX is not set
+# CONFIG_BLK_DEV_ALI15X3 is not set
+# CONFIG_BLK_DEV_AMD74XX is not set
+# CONFIG_BLK_DEV_CMD64X is not set
+# CONFIG_BLK_DEV_TRIFLEX is not set
+# CONFIG_BLK_DEV_CY82C693 is not set
+# CONFIG_BLK_DEV_CS5520 is not set
+# CONFIG_BLK_DEV_CS5530 is not set
+# CONFIG_BLK_DEV_HPT34X is not set
+# CONFIG_BLK_DEV_HPT366 is not set
+# CONFIG_BLK_DEV_SC1200 is not set
+# CONFIG_BLK_DEV_PIIX is not set
+# CONFIG_BLK_DEV_IT821X is not set
+# CONFIG_BLK_DEV_NS87415 is not set
+# CONFIG_BLK_DEV_PDC202XX_OLD is not set
+# CONFIG_BLK_DEV_PDC202XX_NEW is not set
+# CONFIG_BLK_DEV_SVWKS is not set
+# CONFIG_BLK_DEV_SIIMAGE is not set
+# CONFIG_BLK_DEV_SLC90E66 is not set
+# CONFIG_BLK_DEV_TRM290 is not set
+CONFIG_BLK_DEV_VIA82CXXX=y
+# CONFIG_IDE_ARM is not set
+CONFIG_BLK_DEV_IDEDMA=y
+# CONFIG_IDEDMA_IVB is not set
+# CONFIG_IDEDMA_AUTO is not set
+# CONFIG_BLK_DEV_HD is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+
+#
+# Multi-device support (RAID and LVM)
+#
+# CONFIG_MD is not set
+
+#
+# Fusion MPT device support
+#
+# CONFIG_FUSION is not set
+
+#
+# IEEE 1394 (FireWire) support
+#
+# CONFIG_IEEE1394 is not set
+
+#
+# I2O device support
+#
+# CONFIG_I2O is not set
+
+#
+# Macintosh device drivers
+#
+# CONFIG_WINDFARM is not set
+
+#
+# Network device support
+#
+CONFIG_NETDEVICES=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+
+#
+# ARCnet devices
+#
+# CONFIG_ARCNET is not set
+
+#
+# PHY device support
+#
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+# CONFIG_MARVELL_PHY is not set
+# CONFIG_DAVICOM_PHY is not set
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+
+#
+# Ethernet (10 or 100Mbit)
+#
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_HAPPYMEAL is not set
+# CONFIG_SUNGEM is not set
+# CONFIG_CASSINI is not set
+# CONFIG_NET_VENDOR_3COM is not set
+
+#
+# Tulip family network device support
+#
+# CONFIG_NET_TULIP is not set
+# CONFIG_HP100 is not set
+# CONFIG_NET_PCI is not set
+
+#
+# Ethernet (1000 Mbit)
+#
+# CONFIG_ACENIC is not set
+# CONFIG_DL2K is not set
+CONFIG_E1000=y
+CONFIG_E1000_NAPI=y
+# CONFIG_E1000_DISABLE_PACKET_SPLIT is not set
+# CONFIG_NS83820 is not set
+# CONFIG_HAMACHI is not set
+# CONFIG_YELLOWFIN is not set
+# CONFIG_R8169 is not set
+# CONFIG_SIS190 is not set
+# CONFIG_SKGE is not set
+# CONFIG_SKY2 is not set
+# CONFIG_SK98LIN is not set
+# CONFIG_TIGON3 is not set
+# CONFIG_BNX2 is not set
+CONFIG_GIANFAR=y
+CONFIG_GFAR_NAPI=y
+
+#
+# Ethernet (10000 Mbit)
+#
+# CONFIG_CHELSIO_T1 is not set
+# CONFIG_IXGB is not set
+# CONFIG_S2IO is not set
+
+#
+# Token Ring devices
+#
+# CONFIG_TR is not set
+
+#
+# Wireless LAN (non-hamradio)
+#
+# CONFIG_NET_RADIO is not set
+
+#
+# Wan interfaces
+#
+# CONFIG_WAN is not set
+# CONFIG_FDDI is not set
+# CONFIG_HIPPI is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+
+#
+# ISDN subsystem
+#
+# CONFIG_ISDN is not set
+
+#
+# Telephony Support
+#
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+
+#
+# Userland interfaces
+#
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_TSDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_PCI=y
+CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_RUNTIME_UARTS=4
+# CONFIG_SERIAL_8250_EXTENDED is not set
+
+#
+# Non-8250 serial port support
+#
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_JSM is not set
+CONFIG_UNIX98_PTYS=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+
+#
+# IPMI
+#
+# CONFIG_IPMI_HANDLER is not set
+
+#
+# Watchdog Cards
+#
+# CONFIG_WATCHDOG is not set
+# CONFIG_NVRAM is not set
+CONFIG_GEN_RTC=y
+# CONFIG_GEN_RTC_X is not set
+# CONFIG_DTLK is not set
+# CONFIG_R3964 is not set
+# CONFIG_APPLICOM is not set
+
+#
+# Ftape, the floppy tape device driver
+#
+# CONFIG_AGP is not set
+# CONFIG_DRM is not set
+# CONFIG_RAW_DRIVER is not set
+
+#
+# TPM devices
+#
+# CONFIG_TCG_TPM is not set
+# CONFIG_TELCLOCK is not set
+
+#
+# I2C support
+#
+# CONFIG_I2C is not set
+
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+
+#
+# Dallas's 1-wire bus
+#
+# CONFIG_W1 is not set
+
+#
+# Hardware Monitoring support
+#
+CONFIG_HWMON=y
+# CONFIG_HWMON_VID is not set
+# CONFIG_SENSORS_F71805F is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+
+#
+# Misc devices
+#
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+
+#
+# Digital Video Broadcasting Devices
+#
+# CONFIG_DVB is not set
+
+#
+# Graphics support
+#
+# CONFIG_FB is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+
+#
+# USB support
+#
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+CONFIG_USB_ARCH_HAS_EHCI=y
+# CONFIG_USB is not set
+
+#
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+#
+
+#
+# USB Gadget Support
+#
+# CONFIG_USB_GADGET is not set
+
+#
+# MMC/SD Card support
+#
+# CONFIG_MMC is not set
+
+#
+# LED devices
+#
+# CONFIG_NEW_LEDS is not set
+
+#
+# InfiniBand support
+#
+# CONFIG_INFINIBAND is not set
+
+#
+# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
+#
+
+#
+# Real Time Clock
+#
+# CONFIG_RTC_CLASS is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_XATTR=y
+# CONFIG_EXT3_FS_POSIX_ACL is not set
+# CONFIG_EXT3_FS_SECURITY is not set
+CONFIG_JBD=y
+# CONFIG_JBD_DEBUG is not set
+CONFIG_FS_MBCACHE=y
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
+# CONFIG_QUOTA is not set
+CONFIG_DNOTIFY=y
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_HUGETLB_PAGE is not set
+CONFIG_RAMFS=y
+# CONFIG_CONFIGFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+# CONFIG_CRAMFS is not set
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+
+#
+# Network File Systems
+#
+CONFIG_NFS_FS=y
+# CONFIG_NFS_V3 is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+# CONFIG_9P_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+# CONFIG_MSDOS_PARTITION is not set
+# CONFIG_LDM_PARTITION is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+
+#
+# Native Language Support
+#
+# CONFIG_NLS is not set
+
+#
+# Library routines
+#
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+CONFIG_CRC32=y
+# CONFIG_LIBCRC32C is not set
+
+#
+# Instrumentation Support
+#
+# CONFIG_PROFILING is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+# CONFIG_MAGIC_SYSRQ is not set
+CONFIG_DEBUG_KERNEL=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_DETECT_SOFTLOCKUP=y
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_DEBUG_SLAB is not set
+CONFIG_DEBUG_MUTEXES=y
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_KOBJECT is not set
+# CONFIG_DEBUG_INFO is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_DEBUG_VM is not set
+# CONFIG_UNWIND_INFO is not set
+CONFIG_FORCED_INLINING=y
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_DEBUGGER is not set
+# CONFIG_BDI_SWITCH is not set
+# CONFIG_BOOTX_TEXT is not set
+# CONFIG_PPC_EARLY_DEBUG_LPAR is not set
+# CONFIG_PPC_EARLY_DEBUG_G5 is not set
+# CONFIG_PPC_EARLY_DEBUG_RTAS is not set
+# CONFIG_PPC_EARLY_DEBUG_MAPLE is not set
+# CONFIG_PPC_EARLY_DEBUG_ISERIES is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+
+#
+# Cryptographic options
+#
+# CONFIG_CRYPTO is not set
+
+#
+# Hardware crypto devices
+#
diff --git a/arch/powerpc/kernel/cpu_setup_power4.S b/arch/powerpc/kernel/cpu_setup_power4.S
index b61d86e..2714183 100644
--- a/arch/powerpc/kernel/cpu_setup_power4.S
+++ b/arch/powerpc/kernel/cpu_setup_power4.S
@@ -73,23 +73,6 @@
 	isync
 	blr
 
-_GLOBAL(__setup_cpu_power4)
-	blr
-
-_GLOBAL(__setup_cpu_be)
-        /* Set large page sizes LP=0: 16MB, LP=1: 64KB */
-        addi    r3, 0,  0
-        ori     r3, r3, HID6_LB
-        sldi    r3, r3, 32
-        nor     r3, r3, r3
-        mfspr   r4, SPRN_HID6
-        and     r4, r4, r3
-        addi    r3, 0, 0x02000
-        sldi    r3, r3, 32
-        or      r4, r4, r3
-        mtspr   SPRN_HID6, r4
-	blr
-
 _GLOBAL(__setup_cpu_ppc970)
 	mfspr	r0,SPRN_HID0
 	li	r11,5			/* clear DOZE and SLEEP */
diff --git a/arch/powerpc/kernel/cputable.c b/arch/powerpc/kernel/cputable.c
index 3f7182d..0c487ee 100644
--- a/arch/powerpc/kernel/cputable.c
+++ b/arch/powerpc/kernel/cputable.c
@@ -30,11 +30,7 @@
  * part of the cputable though. That has to be fixed for both ppc32
  * and ppc64
  */
-#ifdef CONFIG_PPC64
-extern void __setup_cpu_power3(unsigned long offset, struct cpu_spec* spec);
-extern void __setup_cpu_power4(unsigned long offset, struct cpu_spec* spec);
-extern void __setup_cpu_be(unsigned long offset, struct cpu_spec* spec);
-#else
+#ifdef CONFIG_PPC32
 extern void __setup_cpu_603(unsigned long offset, struct cpu_spec* spec);
 extern void __setup_cpu_604(unsigned long offset, struct cpu_spec* spec);
 extern void __setup_cpu_750(unsigned long offset, struct cpu_spec* spec);
@@ -82,7 +78,6 @@
 		.icache_bsize		= 128,
 		.dcache_bsize		= 128,
 		.num_pmcs		= 8,
-		.cpu_setup		= __setup_cpu_power3,
 		.oprofile_cpu_type	= "ppc64/power3",
 		.oprofile_type		= PPC_OPROFILE_RS64,
 		.platform		= "power3",
@@ -96,7 +91,6 @@
 		.icache_bsize		= 128,
 		.dcache_bsize		= 128,
 		.num_pmcs		= 8,
-		.cpu_setup		= __setup_cpu_power3,
 		.oprofile_cpu_type	= "ppc64/power3",
 		.oprofile_type		= PPC_OPROFILE_RS64,
 		.platform		= "power3",
@@ -110,7 +104,6 @@
 		.icache_bsize		= 128,
 		.dcache_bsize		= 128,
 		.num_pmcs		= 8,
-		.cpu_setup		= __setup_cpu_power3,
 		.oprofile_cpu_type	= "ppc64/rs64",
 		.oprofile_type		= PPC_OPROFILE_RS64,
 		.platform		= "rs64",
@@ -124,7 +117,6 @@
 		.icache_bsize		= 128,
 		.dcache_bsize		= 128,
 		.num_pmcs		= 8,
-		.cpu_setup		= __setup_cpu_power3,
 		.oprofile_cpu_type	= "ppc64/rs64",
 		.oprofile_type		= PPC_OPROFILE_RS64,
 		.platform		= "rs64",
@@ -138,7 +130,6 @@
 		.icache_bsize		= 128,
 		.dcache_bsize		= 128,
 		.num_pmcs		= 8,
-		.cpu_setup		= __setup_cpu_power3,
 		.oprofile_cpu_type	= "ppc64/rs64",
 		.oprofile_type		= PPC_OPROFILE_RS64,
 		.platform		= "rs64",
@@ -152,7 +143,6 @@
 		.icache_bsize		= 128,
 		.dcache_bsize		= 128,
 		.num_pmcs		= 8,
-		.cpu_setup		= __setup_cpu_power3,
 		.oprofile_cpu_type	= "ppc64/rs64",
 		.oprofile_type		= PPC_OPROFILE_RS64,
 		.platform		= "rs64",
@@ -166,7 +156,6 @@
 		.icache_bsize		= 128,
 		.dcache_bsize		= 128,
 		.num_pmcs		= 8,
-		.cpu_setup		= __setup_cpu_power4,
 		.oprofile_cpu_type	= "ppc64/power4",
 		.oprofile_type		= PPC_OPROFILE_POWER4,
 		.platform		= "power4",
@@ -180,7 +169,6 @@
 		.icache_bsize		= 128,
 		.dcache_bsize		= 128,
 		.num_pmcs		= 8,
-		.cpu_setup		= __setup_cpu_power4,
 		.oprofile_cpu_type	= "ppc64/power4",
 		.oprofile_type		= PPC_OPROFILE_POWER4,
 		.platform		= "power4",
@@ -246,7 +234,6 @@
 		.icache_bsize		= 128,
 		.dcache_bsize		= 128,
 		.num_pmcs		= 6,
-		.cpu_setup		= __setup_cpu_power4,
 		.oprofile_cpu_type	= "ppc64/power5",
 		.oprofile_type		= PPC_OPROFILE_POWER4,
 		.platform		= "power5",
@@ -260,7 +247,6 @@
 		.icache_bsize		= 128,
 		.dcache_bsize		= 128,
 		.num_pmcs		= 6,
-		.cpu_setup		= __setup_cpu_power4,
 		.oprofile_cpu_type	= "ppc64/power5+",
 		.oprofile_type		= PPC_OPROFILE_POWER4,
 		.platform		= "power5+",
@@ -274,7 +260,6 @@
 		.icache_bsize		= 128,
 		.dcache_bsize		= 128,
 		.num_pmcs		= 6,
-		.cpu_setup		= __setup_cpu_power4,
 		.oprofile_cpu_type	= "ppc64/power6",
 		.oprofile_type		= PPC_OPROFILE_POWER4,
 		.platform		= "power6",
@@ -289,7 +274,6 @@
 			PPC_FEATURE_SMT,
 		.icache_bsize		= 128,
 		.dcache_bsize		= 128,
-		.cpu_setup		= __setup_cpu_be,
 		.platform		= "ppc-cell-be",
 	},
 	{	/* default match */
@@ -301,7 +285,6 @@
 		.icache_bsize		= 128,
 		.dcache_bsize		= 128,
 		.num_pmcs		= 6,
-		.cpu_setup		= __setup_cpu_power4,
 		.platform		= "power4",
 	}
 #endif	/* CONFIG_PPC64 */
diff --git a/arch/powerpc/kernel/crash.c b/arch/powerpc/kernel/crash.c
index 778f22f..dbcb859 100644
--- a/arch/powerpc/kernel/crash.c
+++ b/arch/powerpc/kernel/crash.c
@@ -22,6 +22,7 @@
 #include <linux/elf.h>
 #include <linux/elfcore.h>
 #include <linux/init.h>
+#include <linux/irq.h>
 #include <linux/types.h>
 
 #include <asm/processor.h>
@@ -174,6 +175,8 @@
 
 void default_machine_crash_shutdown(struct pt_regs *regs)
 {
+	unsigned int irq;
+
 	/*
 	 * This function is only called after the system
 	 * has paniced or is otherwise in a critical state.
@@ -186,6 +189,16 @@
 	 */
 	local_irq_disable();
 
+	for_each_irq(irq) {
+		struct irq_desc *desc = irq_descp(irq);
+
+		if (desc->status & IRQ_INPROGRESS)
+			desc->handler->end(irq);
+
+		if (!(desc->status & IRQ_DISABLED))
+			desc->handler->disable(irq);
+	}
+
 	if (ppc_md.kexec_cpu_down)
 		ppc_md.kexec_cpu_down(1, 0);
 
diff --git a/arch/powerpc/kernel/crash_dump.c b/arch/powerpc/kernel/crash_dump.c
index 764d073..371973b 100644
--- a/arch/powerpc/kernel/crash_dump.c
+++ b/arch/powerpc/kernel/crash_dump.c
@@ -25,6 +25,11 @@
 #define DBG(fmt...)
 #endif
 
+void reserve_kdump_trampoline(void)
+{
+	lmb_reserve(0, KDUMP_RESERVE_LIMIT);
+}
+
 static void __init create_trampoline(unsigned long addr)
 {
 	/* The maximum range of a single instruction branch, is the current
@@ -39,11 +44,11 @@
 	create_branch(addr + 4, addr + PHYSICAL_START, 0);
 }
 
-void __init kdump_setup(void)
+void __init setup_kdump_trampoline(void)
 {
 	unsigned long i;
 
-	DBG(" -> kdump_setup()\n");
+	DBG(" -> setup_kdump_trampoline()\n");
 
 	for (i = KDUMP_TRAMPOLINE_START; i < KDUMP_TRAMPOLINE_END; i += 8) {
 		create_trampoline(i);
@@ -52,7 +57,7 @@
 	create_trampoline(__pa(system_reset_fwnmi) - PHYSICAL_START);
 	create_trampoline(__pa(machine_check_fwnmi) - PHYSICAL_START);
 
-	DBG(" <- kdump_setup()\n");
+	DBG(" <- setup_kdump_trampoline()\n");
 }
 
 #ifdef CONFIG_PROC_VMCORE
diff --git a/arch/powerpc/kernel/iomap.c b/arch/powerpc/kernel/iomap.c
index fd8214c..a13a93d 100644
--- a/arch/powerpc/kernel/iomap.c
+++ b/arch/powerpc/kernel/iomap.c
@@ -106,8 +106,6 @@
 
 void __iomem *ioport_map(unsigned long port, unsigned int len)
 {
-	if (!_IO_IS_VALID(port))
-		return NULL;
 	return (void __iomem *) (port+pci_io_base);
 }
 
diff --git a/arch/powerpc/kernel/lparcfg.c b/arch/powerpc/kernel/lparcfg.c
index 2cbde86..c02deaa 100644
--- a/arch/powerpc/kernel/lparcfg.c
+++ b/arch/powerpc/kernel/lparcfg.c
@@ -521,10 +521,10 @@
 
 	current_weight = (resource >> 5 * 8) & 0xFF;
 
-	pr_debug("%s: current_entitled = %lu, current_weight = %lu\n",
+	pr_debug("%s: current_entitled = %lu, current_weight = %u\n",
 		 __FUNCTION__, current_entitled, current_weight);
 
-	pr_debug("%s: new_entitled = %lu, new_weight = %lu\n",
+	pr_debug("%s: new_entitled = %lu, new_weight = %u\n",
 		 __FUNCTION__, *new_entitled_ptr, *new_weight_ptr);
 
 	retval = plpar_hcall_norets(H_SET_PPP, *new_entitled_ptr,
diff --git a/arch/powerpc/kernel/machine_kexec_64.c b/arch/powerpc/kernel/machine_kexec_64.c
index ee166c5..a8fa04e 100644
--- a/arch/powerpc/kernel/machine_kexec_64.c
+++ b/arch/powerpc/kernel/machine_kexec_64.c
@@ -21,6 +21,7 @@
 #include <asm/machdep.h>
 #include <asm/cacheflush.h>
 #include <asm/paca.h>
+#include <asm/lmb.h>
 #include <asm/mmu.h>
 #include <asm/sections.h>	/* _end */
 #include <asm/prom.h>
@@ -335,7 +336,105 @@
 	of_node_put(node);
 }
 
+static struct property crashk_base_prop = {
+	.name = "linux,crashkernel-base",
+	.length = sizeof(unsigned long),
+	.value = (unsigned char *)&crashk_res.start,
+};
+
+static unsigned long crashk_size;
+
+static struct property crashk_size_prop = {
+	.name = "linux,crashkernel-size",
+	.length = sizeof(unsigned long),
+	.value = (unsigned char *)&crashk_size,
+};
+
+static void __init export_crashk_values(void)
+{
+	struct device_node *node;
+	struct property *prop;
+
+	node = of_find_node_by_path("/chosen");
+	if (!node)
+		return;
+
+	/* There might be existing crash kernel properties, but we can't
+	 * be sure what's in them, so remove them. */
+	prop = of_find_property(node, "linux,crashkernel-base", NULL);
+	if (prop)
+		prom_remove_property(node, prop);
+
+	prop = of_find_property(node, "linux,crashkernel-size", NULL);
+	if (prop)
+		prom_remove_property(node, prop);
+
+	if (crashk_res.start != 0) {
+		prom_add_property(node, &crashk_base_prop);
+		crashk_size = crashk_res.end - crashk_res.start + 1;
+		prom_add_property(node, &crashk_size_prop);
+	}
+
+	of_node_put(node);
+}
+
 void __init kexec_setup(void)
 {
 	export_htab_values();
+	export_crashk_values();
+}
+
+static int __init early_parse_crashk(char *p)
+{
+	unsigned long size;
+
+	if (!p)
+		return 1;
+
+	size = memparse(p, &p);
+
+	if (*p == '@')
+		crashk_res.start = memparse(p + 1, &p);
+	else
+		crashk_res.start = KDUMP_KERNELBASE;
+
+	crashk_res.end = crashk_res.start + size - 1;
+
+	return 0;
+}
+early_param("crashkernel", early_parse_crashk);
+
+void __init reserve_crashkernel(void)
+{
+	unsigned long size;
+
+	if (crashk_res.start == 0)
+		return;
+
+	/* We might have got these values via the command line or the
+	 * device tree, either way sanitise them now. */
+
+	size = crashk_res.end - crashk_res.start + 1;
+
+	if (crashk_res.start != KDUMP_KERNELBASE)
+		printk("Crash kernel location must be 0x%x\n",
+				KDUMP_KERNELBASE);
+
+	crashk_res.start = KDUMP_KERNELBASE;
+	size = PAGE_ALIGN(size);
+	crashk_res.end = crashk_res.start + size - 1;
+
+	/* Crash kernel trumps memory limit */
+	if (memory_limit && memory_limit <= crashk_res.end) {
+		memory_limit = crashk_res.end + 1;
+		printk("Adjusted memory limit for crashkernel, now 0x%lx\n",
+				memory_limit);
+	}
+
+	lmb_reserve(crashk_res.start, size);
+}
+
+int overlaps_crashkernel(unsigned long start, unsigned long size)
+{
+	return (start + size) > crashk_res.start && start <= crashk_res.end;
 }
diff --git a/arch/powerpc/kernel/misc_32.S b/arch/powerpc/kernel/misc_32.S
index be98202..01d3916 100644
--- a/arch/powerpc/kernel/misc_32.S
+++ b/arch/powerpc/kernel/misc_32.S
@@ -216,7 +216,7 @@
 	lwz	r4,0(r4)
 	add	r4,r4,r3
 	lwz	r5,CPU_SPEC_SETUP(r4)
-	cmpi	0,r5,0
+	cmpwi	0,r5,0
 	add	r5,r5,r3
 	beqlr
 	mtctr	r5
diff --git a/arch/powerpc/kernel/misc_64.S b/arch/powerpc/kernel/misc_64.S
index 2778cce..e8883d4 100644
--- a/arch/powerpc/kernel/misc_64.S
+++ b/arch/powerpc/kernel/misc_64.S
@@ -482,7 +482,9 @@
 	sub	r0,r3,r5
 	std	r0,0(r4)
 	ld	r4,CPU_SPEC_SETUP(r3)
+	cmpdi	0,r4,0
 	add	r4,r4,r5
+	beqlr
 	ld	r4,0(r4)
 	add	r4,r4,r5
 	mtctr	r4
@@ -768,9 +770,6 @@
 
 #endif /* CONFIG_ALTIVEC */
 
-_GLOBAL(__setup_cpu_power3)
-	blr
-
 _GLOBAL(execve)
 	li	r0,__NR_execve
 	sc
diff --git a/arch/powerpc/kernel/nvram_64.c b/arch/powerpc/kernel/nvram_64.c
index ada50aa..6960f09 100644
--- a/arch/powerpc/kernel/nvram_64.c
+++ b/arch/powerpc/kernel/nvram_64.c
@@ -204,7 +204,7 @@
 	printk(KERN_WARNING "indx\t\tsig\tchks\tlen\tname\n");
 	list_for_each(p, &nvram_part->partition) {
 		tmp_part = list_entry(p, struct nvram_partition, partition);
-		printk(KERN_WARNING "%d    \t%02x\t%02x\t%d\t%s\n",
+		printk(KERN_WARNING "%4d    \t%02x\t%02x\t%d\t%s\n",
 		       tmp_part->index, tmp_part->header.signature,
 		       tmp_part->header.checksum, tmp_part->header.length,
 		       tmp_part->header.name);
diff --git a/arch/powerpc/kernel/pci_64.c b/arch/powerpc/kernel/pci_64.c
index 4c4449b..e1b3b3e 100644
--- a/arch/powerpc/kernel/pci_64.c
+++ b/arch/powerpc/kernel/pci_64.c
@@ -42,14 +42,6 @@
 unsigned long pci_probe_only = 1;
 int pci_assign_all_buses = 0;
 
-/*
- * legal IO pages under MAX_ISA_PORT.  This is to ensure we don't touch
- * devices we don't have access to.
- */
-unsigned long io_page_mask;
-
-EXPORT_SYMBOL(io_page_mask);
-
 #ifdef CONFIG_PPC_MULTIPLATFORM
 static void fixup_resource(struct resource *res, struct pci_dev *dev);
 static void do_bus_setup(struct pci_bus *bus);
@@ -605,7 +597,7 @@
 	iSeries_pcibios_init(); 
 #endif
 
-	printk("PCI: Probing PCI hardware\n");
+	printk(KERN_DEBUG "PCI: Probing PCI hardware\n");
 
 	/* Scan all of the recorded PCI controllers.  */
 	list_for_each_entry_safe(hose, tmp, &hose_list, list_node) {
@@ -630,14 +622,14 @@
 	/* Cache the location of the ISA bridge (if we have one) */
 	ppc64_isabridge_dev = pci_get_class(PCI_CLASS_BRIDGE_ISA << 8, NULL);
 	if (ppc64_isabridge_dev != NULL)
-		printk("ISA bridge at %s\n", pci_name(ppc64_isabridge_dev));
+		printk(KERN_DEBUG "ISA bridge at %s\n", pci_name(ppc64_isabridge_dev));
 
 #ifdef CONFIG_PPC_MULTIPLATFORM
 	/* map in PCI I/O space */
 	phbs_remap_io();
 #endif
 
-	printk("PCI: Probing PCI hardware done\n");
+	printk(KERN_DEBUG "PCI: Probing PCI hardware done\n");
 
 	return 0;
 }
@@ -804,7 +796,7 @@
 	else
 		prot |= _PAGE_GUARDED;
 
-	printk("PCI map for %s:%lx, prot: %lx\n", pci_name(dev), rp->start,
+	printk(KERN_DEBUG "PCI map for %s:%lx, prot: %lx\n", pci_name(dev), rp->start,
 	       prot);
 
 	return __pgprot(prot);
@@ -1104,8 +1096,6 @@
 			pci_process_ISA_OF_ranges(isa_dn, hose->io_base_phys,
 						hose->io_base_virt);
 			of_node_put(isa_dn);
-			/* Allow all IO */
-			io_page_mask = -1;
 		}
 	}
 
@@ -1212,7 +1202,7 @@
 		return 1;
 	if (start_phys == 0)
 		return 1;
-	printk("mapping IO %lx -> %lx, size: %lx\n", start_phys, start_virt, size);
+	printk(KERN_DEBUG "mapping IO %lx -> %lx, size: %lx\n", start_phys, start_virt, size);
 	if (__ioremap_explicit(start_phys, start_virt, size,
 			       _PAGE_NO_CACHE | _PAGE_GUARDED))
 		return 1;
@@ -1232,27 +1222,13 @@
 static void __devinit fixup_resource(struct resource *res, struct pci_dev *dev)
 {
 	struct pci_controller *hose = pci_bus_to_host(dev->bus);
-	unsigned long start, end, mask, offset;
+	unsigned long offset;
 
 	if (res->flags & IORESOURCE_IO) {
 		offset = (unsigned long)hose->io_base_virt - pci_io_base;
 
-		start = res->start += offset;
-		end = res->end += offset;
-
-		/* Need to allow IO access to pages that are in the
-		   ISA range */
-		if (start < MAX_ISA_PORT) {
-			if (end > MAX_ISA_PORT)
-				end = MAX_ISA_PORT;
-
-			start >>= PAGE_SHIFT;
-			end >>= PAGE_SHIFT;
-
-			/* get the range of pages for the map */
-			mask = ((1 << (end+1)) - 1) ^ ((1 << start) - 1);
-			io_page_mask |= mask;
-		}
+		res->start += offset;
+		res->end += offset;
 	} else if (res->flags & IORESOURCE_MEM) {
 		res->start += hose->pci_mem_offset;
 		res->end += hose->pci_mem_offset;
diff --git a/arch/powerpc/kernel/pci_iommu.c b/arch/powerpc/kernel/pci_iommu.c
index c1d95e1..48aa82d 100644
--- a/arch/powerpc/kernel/pci_iommu.c
+++ b/arch/powerpc/kernel/pci_iommu.c
@@ -44,16 +44,16 @@
  */
 #define PCI_GET_DN(dev) ((struct device_node *)((dev)->sysdata))
 
-static inline struct iommu_table *devnode_table(struct device *dev)
+static inline struct iommu_table *device_to_table(struct device *hwdev)
 {
 	struct pci_dev *pdev;
 
-	if (!dev) {
+	if (!hwdev) {
 		pdev = ppc64_isabridge_dev;
 		if (!pdev)
 			return NULL;
 	} else
-		pdev = to_pci_dev(dev);
+		pdev = to_pci_dev(hwdev);
 
 	return PCI_DN(PCI_GET_DN(pdev))->iommu_table;
 }
@@ -85,14 +85,14 @@
 static void *pci_iommu_alloc_coherent(struct device *hwdev, size_t size,
 			   dma_addr_t *dma_handle, gfp_t flag)
 {
-	return iommu_alloc_coherent(devnode_table(hwdev), size, dma_handle,
+	return iommu_alloc_coherent(device_to_table(hwdev), size, dma_handle,
 			device_to_mask(hwdev), flag);
 }
 
 static void pci_iommu_free_coherent(struct device *hwdev, size_t size,
 			 void *vaddr, dma_addr_t dma_handle)
 {
-	iommu_free_coherent(devnode_table(hwdev), size, vaddr, dma_handle);
+	iommu_free_coherent(device_to_table(hwdev), size, vaddr, dma_handle);
 }
 
 /* Creates TCEs for a user provided buffer.  The user buffer must be 
@@ -104,7 +104,7 @@
 static dma_addr_t pci_iommu_map_single(struct device *hwdev, void *vaddr,
 		size_t size, enum dma_data_direction direction)
 {
-	return iommu_map_single(devnode_table(hwdev), vaddr, size,
+	return iommu_map_single(device_to_table(hwdev), vaddr, size,
 			        device_to_mask(hwdev), direction);
 }
 
@@ -112,27 +112,27 @@
 static void pci_iommu_unmap_single(struct device *hwdev, dma_addr_t dma_handle,
 		size_t size, enum dma_data_direction direction)
 {
-	iommu_unmap_single(devnode_table(hwdev), dma_handle, size, direction);
+	iommu_unmap_single(device_to_table(hwdev), dma_handle, size, direction);
 }
 
 
 static int pci_iommu_map_sg(struct device *pdev, struct scatterlist *sglist,
 		int nelems, enum dma_data_direction direction)
 {
-	return iommu_map_sg(pdev, devnode_table(pdev), sglist,
+	return iommu_map_sg(pdev, device_to_table(pdev), sglist,
 			nelems, device_to_mask(pdev), direction);
 }
 
 static void pci_iommu_unmap_sg(struct device *pdev, struct scatterlist *sglist,
 		int nelems, enum dma_data_direction direction)
 {
-	iommu_unmap_sg(devnode_table(pdev), sglist, nelems, direction);
+	iommu_unmap_sg(device_to_table(pdev), sglist, nelems, direction);
 }
 
 /* We support DMA to/from any memory page via the iommu */
 static int pci_iommu_dma_supported(struct device *dev, u64 mask)
 {
-	struct iommu_table *tbl = devnode_table(dev);
+	struct iommu_table *tbl = device_to_table(dev);
 
 	if (!tbl || tbl->it_offset > mask) {
 		printk(KERN_INFO "Warning: IOMMU table offset too big for device mask\n");
diff --git a/arch/powerpc/kernel/proc_ppc64.c b/arch/powerpc/kernel/proc_ppc64.c
index 3c2cf66..2b87f82 100644
--- a/arch/powerpc/kernel/proc_ppc64.c
+++ b/arch/powerpc/kernel/proc_ppc64.c
@@ -52,7 +52,7 @@
 	if (!root)
 		return 1;
 
-	if (!machine_is(pseries) && !machine_is(cell))
+	if (!of_find_node_by_path("/rtas"))
 		return 0;
 
 	if (!proc_mkdir("rtas", root))
diff --git a/arch/powerpc/kernel/prom.c b/arch/powerpc/kernel/prom.c
index 9a07f97..969f4ab 100644
--- a/arch/powerpc/kernel/prom.c
+++ b/arch/powerpc/kernel/prom.c
@@ -50,6 +50,7 @@
 #include <asm/machdep.h>
 #include <asm/pSeries_reconfig.h>
 #include <asm/pci-bridge.h>
+#include <asm/kexec.h>
 
 #ifdef DEBUG
 #define DBG(fmt...) printk(KERN_ERR fmt)
@@ -836,6 +837,42 @@
 	return mem;
 }
 
+static int __init early_parse_mem(char *p)
+{
+	if (!p)
+		return 1;
+
+	memory_limit = PAGE_ALIGN(memparse(p, &p));
+	DBG("memory limit = 0x%lx\n", memory_limit);
+
+	return 0;
+}
+early_param("mem", early_parse_mem);
+
+/*
+ * The device tree may be allocated below our memory limit, or inside the
+ * crash kernel region for kdump. If so, move it out now.
+ */
+static void move_device_tree(void)
+{
+	unsigned long start, size;
+	void *p;
+
+	DBG("-> move_device_tree\n");
+
+	start = __pa(initial_boot_params);
+	size = initial_boot_params->totalsize;
+
+	if ((memory_limit && (start + size) > memory_limit) ||
+			overlaps_crashkernel(start, size)) {
+		p = __va(lmb_alloc_base(size, PAGE_SIZE, lmb.rmo_size));
+		memcpy(p, initial_boot_params, size);
+		initial_boot_params = (struct boot_param_header *)p;
+		DBG("Moved device tree to 0x%p\n", p);
+	}
+
+	DBG("<- move_device_tree\n");
+}
 
 /**
  * unflattens the device-tree passed by the firmware, creating the
@@ -1070,6 +1107,7 @@
 		iommu_force_on = 1;
 #endif
 
+	/* mem=x on the command line is the preferred mechanism */
  	lprop = of_get_flat_dt_prop(node, "linux,memory-limit", NULL);
  	if (lprop)
  		memory_limit = *lprop;
@@ -1123,17 +1161,6 @@
 
 	DBG("Command line is: %s\n", cmd_line);
 
-	if (strstr(cmd_line, "mem=")) {
-		char *p, *q;
-
-		for (q = cmd_line; (p = strstr(q, "mem=")) != 0; ) {
-			q = p + 4;
-			if (p > cmd_line && p[-1] != ' ')
-				continue;
-			memory_limit = memparse(q, &q);
-		}
-	}
-
 	/* break now */
 	return 1;
 }
@@ -1240,6 +1267,11 @@
 
 	reserve_map = (u64 *)(((unsigned long)initial_boot_params) +
 					initial_boot_params->off_mem_rsvmap);
+
+	/* before we do anything, lets reserve the dt blob */
+	lmb_reserve(__pa((unsigned long)initial_boot_params),
+		    initial_boot_params->totalsize);
+
 #ifdef CONFIG_PPC32
 	/* 
 	 * Handle the case where we might be booting from an old kexec
@@ -1292,17 +1324,25 @@
 	lmb_init();
 	of_scan_flat_dt(early_init_dt_scan_root, NULL);
 	of_scan_flat_dt(early_init_dt_scan_memory, NULL);
+
+	/* Save command line for /proc/cmdline and then parse parameters */
+	strlcpy(saved_command_line, cmd_line, COMMAND_LINE_SIZE);
+	parse_early_param();
+
+	/* Reserve LMB regions used by kernel, initrd, dt, etc... */
+	lmb_reserve(PHYSICAL_START, __pa(klimit) - PHYSICAL_START);
+	reserve_kdump_trampoline();
+	reserve_crashkernel();
+	early_reserve_mem();
+
 	lmb_enforce_memory_limit(memory_limit);
 	lmb_analyze();
 
 	DBG("Phys. mem: %lx\n", lmb_phys_mem_size());
 
-	/* Reserve LMB regions used by kernel, initrd, dt, etc... */
-	lmb_reserve(PHYSICAL_START, __pa(klimit) - PHYSICAL_START);
-#ifdef CONFIG_CRASH_DUMP
-	lmb_reserve(0, KDUMP_RESERVE_LIMIT);
-#endif
-	early_reserve_mem();
+	/* We may need to relocate the flat tree, do it now.
+	 * FIXME .. and the initrd too? */
+	move_device_tree();
 
 	DBG("Scanning CPUs ...\n");
 
@@ -2053,29 +2093,3 @@
 	return 0;
 }
 
-#ifdef CONFIG_KEXEC
-/* We may have allocated the flat device tree inside the crash kernel region
- * in prom_init. If so we need to move it out into regular memory. */
-void kdump_move_device_tree(void)
-{
-	unsigned long start, end;
-	struct boot_param_header *new;
-
-	start = __pa((unsigned long)initial_boot_params);
-	end = start + initial_boot_params->totalsize;
-
-	if (end < crashk_res.start || start > crashk_res.end)
-		return;
-
-	new = (struct boot_param_header*)
-		__va(lmb_alloc(initial_boot_params->totalsize, PAGE_SIZE));
-
-	memcpy(new, initial_boot_params, initial_boot_params->totalsize);
-
-	initial_boot_params = new;
-
-	DBG("Flat device tree blob moved to %p\n", initial_boot_params);
-
-	/* XXX should we unreserve the old DT? */
-}
-#endif /* CONFIG_KEXEC */
diff --git a/arch/powerpc/kernel/prom_init.c b/arch/powerpc/kernel/prom_init.c
index 2d80653..12fbdbb 100644
--- a/arch/powerpc/kernel/prom_init.c
+++ b/arch/powerpc/kernel/prom_init.c
@@ -194,19 +194,12 @@
 
 static char __initdata prom_cmd_line[COMMAND_LINE_SIZE];
 
-static unsigned long __initdata prom_memory_limit;
-
 static unsigned long __initdata alloc_top;
 static unsigned long __initdata alloc_top_high;
 static unsigned long __initdata alloc_bottom;
 static unsigned long __initdata rmo_top;
 static unsigned long __initdata ram_top;
 
-#ifdef CONFIG_KEXEC
-static unsigned long __initdata prom_crashk_base;
-static unsigned long __initdata prom_crashk_size;
-#endif
-
 static struct mem_map_entry __initdata mem_reserve_map[MEM_RESERVE_MAP_SIZE];
 static int __initdata mem_reserve_cnt;
 
@@ -593,45 +586,6 @@
 			RELOC(iommu_force_on) = 1;
 	}
 #endif
-
-	opt = strstr(RELOC(prom_cmd_line), RELOC("mem="));
-	if (opt) {
-		opt += 4;
-		RELOC(prom_memory_limit) = prom_memparse(opt, (const char **)&opt);
-#ifdef CONFIG_PPC64
-		/* Align to 16 MB == size of ppc64 large page */
-		RELOC(prom_memory_limit) = ALIGN(RELOC(prom_memory_limit), 0x1000000);
-#endif
-	}
-
-#ifdef CONFIG_KEXEC
-	/*
-	 * crashkernel=size@addr specifies the location to reserve for
-	 * crash kernel.
-	 */
-	opt = strstr(RELOC(prom_cmd_line), RELOC("crashkernel="));
-	if (opt) {
-		opt += 12;
-		RELOC(prom_crashk_size) = 
-			prom_memparse(opt, (const char **)&opt);
-
-		if (ALIGN(RELOC(prom_crashk_size), 0x1000000) !=
-			RELOC(prom_crashk_size)) {
-			prom_printf("Warning: crashkernel size is not "
-					"aligned to 16MB\n");
-		}
-
-		/*
-		 * At present, the crash kernel always run at 32MB.
-		 * Just ignore whatever user passed.
-		 */
-		RELOC(prom_crashk_base) = 0x2000000;
-		if (*opt == '@') {
-			prom_printf("Warning: PPC64 kdump kernel always runs "
-					"at 32 MB\n");
-		}
-	}
-#endif
 }
 
 #ifdef CONFIG_PPC_PSERIES
@@ -1115,29 +1069,6 @@
 	}
 
 	/*
-	 * If prom_memory_limit is set we reduce the upper limits *except* for
-	 * alloc_top_high. This must be the real top of RAM so we can put
-	 * TCE's up there.
-	 */
-
-	RELOC(alloc_top_high) = RELOC(ram_top);
-
-	if (RELOC(prom_memory_limit)) {
-		if (RELOC(prom_memory_limit) <= RELOC(alloc_bottom)) {
-			prom_printf("Ignoring mem=%x <= alloc_bottom.\n",
-				RELOC(prom_memory_limit));
-			RELOC(prom_memory_limit) = 0;
-		} else if (RELOC(prom_memory_limit) >= RELOC(ram_top)) {
-			prom_printf("Ignoring mem=%x >= ram_top.\n",
-				RELOC(prom_memory_limit));
-			RELOC(prom_memory_limit) = 0;
-		} else {
-			RELOC(ram_top) = RELOC(prom_memory_limit);
-			RELOC(rmo_top) = min(RELOC(rmo_top), RELOC(prom_memory_limit));
-		}
-	}
-
-	/*
 	 * Setup our top alloc point, that is top of RMO or top of
 	 * segment 0 when running non-LPAR.
 	 * Some RS64 machines have buggy firmware where claims up at
@@ -1149,20 +1080,14 @@
 		RELOC(rmo_top) = RELOC(ram_top);
 	RELOC(rmo_top) = min(0x30000000ul, RELOC(rmo_top));
 	RELOC(alloc_top) = RELOC(rmo_top);
+	RELOC(alloc_top_high) = RELOC(ram_top);
 
 	prom_printf("memory layout at init:\n");
-	prom_printf("  memory_limit : %x (16 MB aligned)\n", RELOC(prom_memory_limit));
 	prom_printf("  alloc_bottom : %x\n", RELOC(alloc_bottom));
 	prom_printf("  alloc_top    : %x\n", RELOC(alloc_top));
 	prom_printf("  alloc_top_hi : %x\n", RELOC(alloc_top_high));
 	prom_printf("  rmo_top      : %x\n", RELOC(rmo_top));
 	prom_printf("  ram_top      : %x\n", RELOC(ram_top));
-#ifdef CONFIG_KEXEC
-	if (RELOC(prom_crashk_base)) {
-		prom_printf("  crashk_base  : %x\n",  RELOC(prom_crashk_base));
-		prom_printf("  crashk_size  : %x\n", RELOC(prom_crashk_size));
-	}
-#endif
 }
 
 
@@ -1348,16 +1273,10 @@
 
 	reserve_mem(local_alloc_bottom, local_alloc_top - local_alloc_bottom);
 
-	if (RELOC(prom_memory_limit)) {
-		/*
-		 * We align the start to a 16MB boundary so we can map
-		 * the TCE area using large pages if possible.
-		 * The end should be the top of RAM so no need to align it.
-		 */
-		RELOC(prom_tce_alloc_start) = _ALIGN_DOWN(local_alloc_bottom,
-							  0x1000000);
-		RELOC(prom_tce_alloc_end) = local_alloc_top;
-	}
+	/* These are only really needed if there is a memory limit in
+	 * effect, but we don't know so export them always. */
+	RELOC(prom_tce_alloc_start) = local_alloc_bottom;
+	RELOC(prom_tce_alloc_end) = local_alloc_top;
 
 	/* Flag the first invalid entry */
 	prom_debug("ending prom_initialize_tce_table\n");
@@ -2031,11 +1950,7 @@
 	/* Version 16 is not backward compatible */
 	hdr->last_comp_version = 0x10;
 
-	/* Reserve the whole thing and copy the reserve map in, we
-	 * also bump mem_reserve_cnt to cause further reservations to
-	 * fail since it's too late.
-	 */
-	reserve_mem(RELOC(dt_header_start), hdr->totalsize);
+	/* Copy the reserve map in */
 	memcpy(rsvmap, RELOC(mem_reserve_map), sizeof(mem_reserve_map));
 
 #ifdef DEBUG_PROM
@@ -2048,6 +1963,9 @@
 				    RELOC(mem_reserve_map)[i].size);
 	}
 #endif
+	/* Bump mem_reserve_cnt to cause further reservations to fail
+	 * since it's too late.
+	 */
 	RELOC(mem_reserve_cnt) = MEM_RESERVE_MAP_SIZE;
 
 	prom_printf("Device tree strings 0x%x -> 0x%x\n",
@@ -2228,10 +2146,6 @@
 	 */
 	prom_init_mem();
 
-#ifdef CONFIG_KEXEC
-	if (RELOC(prom_crashk_base))
-		reserve_mem(RELOC(prom_crashk_base), RELOC(prom_crashk_size));
-#endif
 	/*
 	 * Determine which cpu is actually running right _now_
 	 */
@@ -2265,10 +2179,6 @@
 	/*
 	 * Fill in some infos for use by the kernel later on
 	 */
-	if (RELOC(prom_memory_limit))
-		prom_setprop(_prom->chosen, "/chosen", "linux,memory-limit",
-			     &RELOC(prom_memory_limit),
-			     sizeof(prom_memory_limit));
 #ifdef CONFIG_PPC64
 	if (RELOC(ppc64_iommu_off))
 		prom_setprop(_prom->chosen, "/chosen", "linux,iommu-off",
@@ -2288,16 +2198,6 @@
 	}
 #endif
 
-#ifdef CONFIG_KEXEC
-	if (RELOC(prom_crashk_base)) {
-		prom_setprop(_prom->chosen, "/chosen", "linux,crashkernel-base",
-			PTRRELOC(&prom_crashk_base),
-			sizeof(RELOC(prom_crashk_base)));
-		prom_setprop(_prom->chosen, "/chosen", "linux,crashkernel-size",
-			PTRRELOC(&prom_crashk_size),
-			sizeof(RELOC(prom_crashk_size)));
-	}
-#endif
 	/*
 	 * Fixup any known bugs in the device-tree
 	 */
diff --git a/arch/powerpc/kernel/prom_parse.c b/arch/powerpc/kernel/prom_parse.c
index 3934c22..23bb060 100644
--- a/arch/powerpc/kernel/prom_parse.c
+++ b/arch/powerpc/kernel/prom_parse.c
@@ -548,3 +548,25 @@
 	return __of_address_to_resource(dev, addrp, size, flags, r);
 }
 EXPORT_SYMBOL_GPL(of_pci_address_to_resource);
+
+void of_parse_dma_window(struct device_node *dn, unsigned char *dma_window_prop,
+		unsigned long *busno, unsigned long *phys, unsigned long *size)
+{
+	u32 *dma_window, cells;
+	unsigned char *prop;
+
+	dma_window = (u32 *)dma_window_prop;
+
+	/* busno is always one cell */
+	*busno = *(dma_window++);
+
+	prop = get_property(dn, "ibm,#dma-address-cells", NULL);
+	cells = prop ? *(u32 *)prop : prom_n_addr_cells(dn);
+	*phys = of_read_addr(dma_window, cells);
+
+	dma_window += cells;
+
+	prop = get_property(dn, "ibm,#dma-size-cells", NULL);
+	cells = prop ? *(u32 *)prop : prom_n_size_cells(dn);
+	*size = of_read_addr(dma_window, cells);
+}
diff --git a/arch/powerpc/kernel/setup-common.c b/arch/powerpc/kernel/setup-common.c
index 684ab1d..bd32812 100644
--- a/arch/powerpc/kernel/setup-common.c
+++ b/arch/powerpc/kernel/setup-common.c
@@ -443,6 +443,7 @@
 }
 #endif /* CONFIG_SMP */
 
+int __initdata do_early_xmon;
 #ifdef CONFIG_XMON
 static int __init early_xmon(char *p)
 {
@@ -456,7 +457,7 @@
 			return 0;
 	}
 	xmon_init(1);
-	debugger(NULL);
+	do_early_xmon = 1;
 
 	return 0;
 }
@@ -524,3 +525,20 @@
 	return ppc_md.check_legacy_ioport(base_port);
 }
 EXPORT_SYMBOL(check_legacy_ioport);
+
+static int ppc_panic_event(struct notifier_block *this,
+                             unsigned long event, void *ptr)
+{
+	ppc_md.panic(ptr);  /* May not return */
+	return NOTIFY_DONE;
+}
+
+static struct notifier_block ppc_panic_block = {
+	.notifier_call = ppc_panic_event,
+	.priority = INT_MIN /* may not return; must be done last */
+};
+
+void __init setup_panic(void)
+{
+	atomic_notifier_chain_register(&panic_notifier_list, &ppc_panic_block);
+}
diff --git a/arch/powerpc/kernel/setup.h b/arch/powerpc/kernel/setup.h
index 2ebba75..4c67ad7 100644
--- a/arch/powerpc/kernel/setup.h
+++ b/arch/powerpc/kernel/setup.h
@@ -2,5 +2,8 @@
 #define _POWERPC_KERNEL_SETUP_H
 
 void check_for_initrd(void);
+void do_init_bootmem(void);
+void setup_panic(void);
+extern int do_early_xmon;
 
 #endif /* _POWERPC_KERNEL_SETUP_H */
diff --git a/arch/powerpc/kernel/setup_32.c b/arch/powerpc/kernel/setup_32.c
index 69ac257..e5a4481 100644
--- a/arch/powerpc/kernel/setup_32.c
+++ b/arch/powerpc/kernel/setup_32.c
@@ -131,12 +131,6 @@
 	/* Do some early initialization based on the flat device tree */
 	early_init_devtree(__va(dt_ptr));
 
-	/* Check default command line */
-#ifdef CONFIG_CMDLINE
-	if (cmd_line[0] == 0)
-		strlcpy(cmd_line, CONFIG_CMDLINE, sizeof(cmd_line));
-#endif /* CONFIG_CMDLINE */
-
 	probe_machine();
 
 #ifdef CONFIG_6xx
@@ -235,7 +229,7 @@
 /* Warning, IO base is not yet inited */
 void __init setup_arch(char **cmdline_p)
 {
-	extern void do_init_bootmem(void);
+	*cmdline_p = cmd_line;
 
 	/* so udelay does something sensible, assume <= 1000 bogomips */
 	loops_per_jiffy = 500000000 / HZ;
@@ -285,16 +279,16 @@
 	/* reboot on panic */
 	panic_timeout = 180;
 
+	if (ppc_md.panic)
+		setup_panic();
+
 	init_mm.start_code = PAGE_OFFSET;
 	init_mm.end_code = (unsigned long) _etext;
 	init_mm.end_data = (unsigned long) _edata;
 	init_mm.brk = klimit;
 
-	/* Save unparsed command line copy for /proc/cmdline */
-	strlcpy(saved_command_line, cmd_line, COMMAND_LINE_SIZE);
-	*cmdline_p = cmd_line;
-
-	parse_early_param();
+	if (do_early_xmon)
+		debugger(NULL);
 
 	/* set up the bootmem stuff with available memory */
 	do_init_bootmem();
diff --git a/arch/powerpc/kernel/setup_64.c b/arch/powerpc/kernel/setup_64.c
index 4467c49..78f3a5f 100644
--- a/arch/powerpc/kernel/setup_64.c
+++ b/arch/powerpc/kernel/setup_64.c
@@ -100,12 +100,6 @@
 #endif /* CONFIG_MAGIC_SYSRQ */
 
 
-static int ppc64_panic_event(struct notifier_block *, unsigned long, void *);
-static struct notifier_block ppc64_panic_block = {
-	.notifier_call = ppc64_panic_event,
-	.priority = INT_MIN /* may not return; must be done last */
-};
-
 #ifdef CONFIG_SMP
 
 static int smt_enabled_cmdline;
@@ -199,9 +193,7 @@
 	/* Probe the machine type */
 	probe_machine();
 
-#ifdef CONFIG_CRASH_DUMP
-	kdump_setup();
-#endif
+	setup_kdump_trampoline();
 
 	DBG("Found, Initializing memory management...\n");
 
@@ -353,9 +345,6 @@
 {
 	DBG(" -> setup_system()\n");
 
-#ifdef CONFIG_KEXEC
-	kdump_move_device_tree();
-#endif
 	/*
 	 * Unflatten the device-tree passed by prom_init or kexec
 	 */
@@ -420,10 +409,8 @@
 	 */
 	register_early_udbg_console();
 
-	/* Save unparsed command line copy for /proc/cmdline */
-	strlcpy(saved_command_line, cmd_line, COMMAND_LINE_SIZE);
-
-	parse_early_param();
+	if (do_early_xmon)
+		debugger(NULL);
 
 	check_smt_enabled();
 	smp_setup_cpu_maps();
@@ -456,13 +443,6 @@
 	DBG(" <- setup_system()\n");
 }
 
-static int ppc64_panic_event(struct notifier_block *this,
-                             unsigned long event, void *ptr)
-{
-	ppc_md.panic((char *)ptr);  /* May not return */
-	return NOTIFY_DONE;
-}
-
 #ifdef CONFIG_IRQSTACKS
 static void __init irqstack_early_init(void)
 {
@@ -517,8 +497,6 @@
  */
 void __init setup_arch(char **cmdline_p)
 {
-	extern void do_init_bootmem(void);
-
 	ppc64_boot_msg(0x12, "Setup Arch");
 
 	*cmdline_p = cmd_line;
@@ -535,8 +513,7 @@
 	panic_timeout = 180;
 
 	if (ppc_md.panic)
-		atomic_notifier_chain_register(&panic_notifier_list,
-				&ppc64_panic_block);
+		setup_panic();
 
 	init_mm.start_code = PAGE_OFFSET;
 	init_mm.end_code = (unsigned long) _etext;
diff --git a/arch/powerpc/kernel/time.c b/arch/powerpc/kernel/time.c
index 24e3ad7..528e7f8 100644
--- a/arch/powerpc/kernel/time.c
+++ b/arch/powerpc/kernel/time.c
@@ -76,7 +76,6 @@
 
 /* keep track of when we need to update the rtc */
 time_t last_rtc_update;
-extern int piranha_simulator;
 #ifdef CONFIG_PPC_ISERIES
 unsigned long iSeries_recal_titan = 0;
 unsigned long iSeries_recal_tb = 0; 
@@ -945,9 +944,9 @@
 	} else {
 		/* Normal PowerPC with timebase register */
 		ppc_md.calibrate_decr();
-		printk(KERN_INFO "time_init: decrementer frequency = %lu.%.6lu MHz\n",
+		printk(KERN_DEBUG "time_init: decrementer frequency = %lu.%.6lu MHz\n",
 		       ppc_tb_freq / 1000000, ppc_tb_freq % 1000000);
-		printk(KERN_INFO "time_init: processor frequency   = %lu.%.6lu MHz\n",
+		printk(KERN_DEBUG "time_init: processor frequency   = %lu.%.6lu MHz\n",
 		       ppc_proc_freq / 1000000, ppc_proc_freq % 1000000);
 		tb_last_stamp = tb_last_jiffy = get_tb();
 	}
@@ -1010,10 +1009,7 @@
 	tb_to_ns_scale = scale;
 	tb_to_ns_shift = shift;
 
-#ifdef CONFIG_PPC_ISERIES
-	if (!piranha_simulator)
-#endif
-		tm = get_boot_time();
+	tm = get_boot_time();
 
 	write_seqlock_irqsave(&xtime_lock, flags);
 
diff --git a/arch/powerpc/kernel/vio.c b/arch/powerpc/kernel/vio.c
index 971020c..fe92727 100644
--- a/arch/powerpc/kernel/vio.c
+++ b/arch/powerpc/kernel/vio.c
@@ -13,27 +13,116 @@
  *      2 of the License, or (at your option) any later version.
  */
 
+#include <linux/types.h>
+#include <linux/device.h>
 #include <linux/init.h>
 #include <linux/console.h>
 #include <linux/module.h>
 #include <linux/mm.h>
 #include <linux/dma-mapping.h>
+#include <linux/kobject.h>
+
 #include <asm/iommu.h>
 #include <asm/dma.h>
 #include <asm/vio.h>
 #include <asm/prom.h>
+#include <asm/firmware.h>
+#include <asm/tce.h>
+#include <asm/abs_addr.h>
+#include <asm/page.h>
+#include <asm/hvcall.h>
+#include <asm/iseries/vio.h>
+#include <asm/iseries/hv_types.h>
+#include <asm/iseries/hv_lp_config.h>
+#include <asm/iseries/hv_call_xm.h>
+#include <asm/iseries/iommu.h>
 
-static const struct vio_device_id *vio_match_device(
-		const struct vio_device_id *, const struct vio_dev *);
+extern struct subsystem devices_subsys; /* needed for vio_find_name() */
 
-struct vio_dev vio_bus_device  = { /* fake "parent" device */
+static struct vio_dev vio_bus_device  = { /* fake "parent" device */
 	.name = vio_bus_device.dev.bus_id,
 	.type = "",
 	.dev.bus_id = "vio",
 	.dev.bus = &vio_bus_type,
 };
 
-static struct vio_bus_ops vio_bus_ops;
+#ifdef CONFIG_PPC_ISERIES
+struct device *iSeries_vio_dev = &vio_bus_device.dev;
+EXPORT_SYMBOL(iSeries_vio_dev);
+
+static struct iommu_table veth_iommu_table;
+static struct iommu_table vio_iommu_table;
+
+static void __init iommu_vio_init(void)
+{
+	iommu_table_getparms_iSeries(255, 0, 0xff, &veth_iommu_table);
+	veth_iommu_table.it_size /= 2;
+	vio_iommu_table = veth_iommu_table;
+	vio_iommu_table.it_offset += veth_iommu_table.it_size;
+
+	if (!iommu_init_table(&veth_iommu_table))
+		printk("Virtual Bus VETH TCE table failed.\n");
+	if (!iommu_init_table(&vio_iommu_table))
+		printk("Virtual Bus VIO TCE table failed.\n");
+}
+#endif
+
+static struct iommu_table *vio_build_iommu_table(struct vio_dev *dev)
+{
+#ifdef CONFIG_PPC_ISERIES
+	if (firmware_has_feature(FW_FEATURE_ISERIES)) {
+		if (strcmp(dev->type, "network") == 0)
+			return &veth_iommu_table;
+		return &vio_iommu_table;
+	} else
+#endif
+	{
+		unsigned char *dma_window;
+		struct iommu_table *tbl;
+		unsigned long offset, size;
+
+		dma_window = get_property(dev->dev.platform_data,
+				"ibm,my-dma-window", NULL);
+		if (!dma_window)
+			return NULL;
+
+		tbl = kmalloc(sizeof(*tbl), GFP_KERNEL);
+
+		of_parse_dma_window(dev->dev.platform_data, dma_window,
+				&tbl->it_index, &offset, &size);
+
+		/* TCE table size - measured in tce entries */
+		tbl->it_size = size >> PAGE_SHIFT;
+		/* offset for VIO should always be 0 */
+		tbl->it_offset = offset >> PAGE_SHIFT;
+		tbl->it_busno = 0;
+		tbl->it_type = TCE_VB;
+
+		return iommu_init_table(tbl);
+	}
+}
+
+/**
+ * vio_match_device: - Tell if a VIO device has a matching
+ *			VIO device id structure.
+ * @ids:	array of VIO device id structures to search in
+ * @dev:	the VIO device structure to match against
+ *
+ * Used by a driver to check whether a VIO device present in the
+ * system is in its list of supported devices. Returns the matching
+ * vio_device_id structure or NULL if there is no match.
+ */
+static const struct vio_device_id *vio_match_device(
+		const struct vio_device_id *ids, const struct vio_dev *dev)
+{
+	while (ids->type[0] != '\0') {
+		if ((strncmp(dev->type, ids->type, strlen(ids->type)) == 0) &&
+		    device_is_compatible(dev->dev.platform_data, ids->compat))
+			return ids;
+		ids++;
+	}
+	return NULL;
+}
 
 /*
  * Convert from struct device to struct vio_dev and pass to driver.
@@ -106,35 +195,110 @@
 }
 EXPORT_SYMBOL(vio_unregister_driver);
 
-/**
- * vio_match_device: - Tell if a VIO device has a matching
- *			VIO device id structure.
- * @ids:	array of VIO device id structures to search in
- * @dev:	the VIO device structure to match against
- *
- * Used by a driver to check whether a VIO device present in the
- * system is in its list of supported devices. Returns the matching
- * vio_device_id structure or NULL if there is no match.
- */
-static const struct vio_device_id *vio_match_device(
-		const struct vio_device_id *ids, const struct vio_dev *dev)
+/* vio_dev refcount hit 0 */
+static void __devinit vio_dev_release(struct device *dev)
 {
-	while (ids->type[0] != '\0') {
-		if (vio_bus_ops.match(ids, dev))
-			return ids;
-		ids++;
+	if (dev->platform_data) {
+		/* XXX free TCE table */
+		of_node_put(dev->platform_data);
 	}
-	return NULL;
+	kfree(to_vio_dev(dev));
 }
 
 /**
+ * vio_register_device_node: - Register a new vio device.
+ * @of_node:	The OF node for this device.
+ *
+ * Creates and initializes a vio_dev structure from the data in
+ * of_node (dev.platform_data) and adds it to the list of virtual devices.
+ * Returns a pointer to the created vio_dev or NULL if node has
+ * NULL device_type or compatible fields.
+ */
+struct vio_dev * __devinit vio_register_device_node(struct device_node *of_node)
+{
+	struct vio_dev *viodev;
+	unsigned int *unit_address;
+	unsigned int *irq_p;
+
+	/* we need the 'device_type' property, in order to match with drivers */
+	if (of_node->type == NULL) {
+		printk(KERN_WARNING "%s: node %s missing 'device_type'\n",
+				__FUNCTION__,
+				of_node->name ? of_node->name : "<unknown>");
+		return NULL;
+	}
+
+	unit_address = (unsigned int *)get_property(of_node, "reg", NULL);
+	if (unit_address == NULL) {
+		printk(KERN_WARNING "%s: node %s missing 'reg'\n",
+				__FUNCTION__,
+				of_node->name ? of_node->name : "<unknown>");
+		return NULL;
+	}
+
+	/* allocate a vio_dev for this node */
+	viodev = kzalloc(sizeof(struct vio_dev), GFP_KERNEL);
+	if (viodev == NULL)
+		return NULL;
+
+	viodev->dev.platform_data = of_node_get(of_node);
+
+	viodev->irq = NO_IRQ;
+	irq_p = (unsigned int *)get_property(of_node, "interrupts", NULL);
+	if (irq_p) {
+		int virq = virt_irq_create_mapping(*irq_p);
+		if (virq == NO_IRQ) {
+			printk(KERN_ERR "Unable to allocate interrupt "
+			       "number for %s\n", of_node->full_name);
+		} else
+			viodev->irq = irq_offset_up(virq);
+	}
+
+	snprintf(viodev->dev.bus_id, BUS_ID_SIZE, "%x", *unit_address);
+	viodev->name = of_node->name;
+	viodev->type = of_node->type;
+	viodev->unit_address = *unit_address;
+	if (firmware_has_feature(FW_FEATURE_ISERIES)) {
+		unit_address = (unsigned int *)get_property(of_node,
+				"linux,unit_address", NULL);
+		if (unit_address != NULL)
+			viodev->unit_address = *unit_address;
+	}
+	viodev->iommu_table = vio_build_iommu_table(viodev);
+
+	/* init generic 'struct device' fields: */
+	viodev->dev.parent = &vio_bus_device.dev;
+	viodev->dev.bus = &vio_bus_type;
+	viodev->dev.release = vio_dev_release;
+
+	/* register with generic device framework */
+	if (device_register(&viodev->dev)) {
+		printk(KERN_ERR "%s: failed to register device %s\n",
+				__FUNCTION__, viodev->dev.bus_id);
+		/* XXX free TCE table */
+		kfree(viodev);
+		return NULL;
+	}
+
+	return viodev;
+}
+EXPORT_SYMBOL(vio_register_device_node);
+
+/**
  * vio_bus_init: - Initialize the virtual IO bus
  */
-int __init vio_bus_init(struct vio_bus_ops *ops)
+static int __init vio_bus_init(void)
 {
 	int err;
+	struct device_node *node_vroot;
 
-	vio_bus_ops = *ops;
+#ifdef CONFIG_PPC_ISERIES
+	if (firmware_has_feature(FW_FEATURE_ISERIES)) {
+		iommu_vio_init();
+		vio_bus_device.iommu_table = &vio_iommu_table;
+		iSeries_vio_dev = &vio_bus_device.dev;
+	}
+#endif
 
 	err = bus_register(&vio_bus_type);
 	if (err) {
@@ -153,47 +317,48 @@
 		return err;
 	}
 
+	node_vroot = find_devices("vdevice");
+	if (node_vroot) {
+		struct device_node *of_node;
+
+		/*
+		 * Create struct vio_devices for each virtual device in
+		 * the device tree. Drivers will associate with them later.
+		 */
+		for (of_node = node_vroot->child; of_node != NULL;
+				of_node = of_node->sibling) {
+			printk(KERN_DEBUG "%s: processing %p\n",
+					__FUNCTION__, of_node);
+			vio_register_device_node(of_node);
+		}
+	}
+
 	return 0;
 }
+__initcall(vio_bus_init);
 
-/* vio_dev refcount hit 0 */
-static void __devinit vio_dev_release(struct device *dev)
-{
-	if (vio_bus_ops.release_device)
-		vio_bus_ops.release_device(dev);
-	kfree(to_vio_dev(dev));
-}
-
-static ssize_t viodev_show_name(struct device *dev,
+static ssize_t name_show(struct device *dev,
 		struct device_attribute *attr, char *buf)
 {
 	return sprintf(buf, "%s\n", to_vio_dev(dev)->name);
 }
-DEVICE_ATTR(name, S_IRUSR | S_IRGRP | S_IROTH, viodev_show_name, NULL);
 
-struct vio_dev * __devinit vio_register_device(struct vio_dev *viodev)
+static ssize_t devspec_show(struct device *dev,
+		struct device_attribute *attr, char *buf)
 {
-	/* init generic 'struct device' fields: */
-	viodev->dev.parent = &vio_bus_device.dev;
-	viodev->dev.bus = &vio_bus_type;
-	viodev->dev.release = vio_dev_release;
+	struct device_node *of_node = dev->platform_data;
 
-	/* register with generic device framework */
-	if (device_register(&viodev->dev)) {
-		printk(KERN_ERR "%s: failed to register device %s\n",
-				__FUNCTION__, viodev->dev.bus_id);
-		return NULL;
-	}
-	device_create_file(&viodev->dev, &dev_attr_name);
-
-	return viodev;
+	return sprintf(buf, "%s\n", of_node ? of_node->full_name : "none");
 }
 
+static struct device_attribute vio_dev_attrs[] = {
+	__ATTR_RO(name),
+	__ATTR_RO(devspec),
+	__ATTR_NULL
+};
+
 void __devinit vio_unregister_device(struct vio_dev *viodev)
 {
-	if (vio_bus_ops.unregister_device)
-		vio_bus_ops.unregister_device(viodev);
-	device_remove_file(&viodev->dev, &dev_attr_name);
 	device_unregister(&viodev->dev);
 }
 EXPORT_SYMBOL(vio_unregister_device);
@@ -267,22 +432,23 @@
 			char *buffer, int buffer_size)
 {
 	const struct vio_dev *vio_dev = to_vio_dev(dev);
+	struct device_node *dn = dev->platform_data;
 	char *cp;
 	int length;
 
 	if (!num_envp)
 		return -ENOMEM;
 
-	if (!vio_dev->dev.platform_data)
+	if (!dn)
 		return -ENODEV;
-	cp = (char *)get_property(vio_dev->dev.platform_data, "compatible", &length);
+	cp = (char *)get_property(dn, "compatible", &length);
 	if (!cp)
 		return -ENODEV;
 
 	envp[0] = buffer;
 	length = scnprintf(buffer, buffer_size, "MODALIAS=vio:T%sS%s",
 				vio_dev->type, cp);
-	if (buffer_size - length <= 0)
+	if ((buffer_size - length) <= 0)
 		return -ENOMEM;
 	envp[1] = NULL;
 	return 0;
@@ -290,9 +456,81 @@
 
 struct bus_type vio_bus_type = {
 	.name = "vio",
+	.dev_attrs = vio_dev_attrs,
 	.uevent = vio_hotplug,
 	.match = vio_bus_match,
 	.probe = vio_bus_probe,
 	.remove = vio_bus_remove,
 	.shutdown = vio_bus_shutdown,
 };
+
+/**
+ * vio_get_attribute: - get attribute for virtual device
+ * @vdev:	The vio device to get property.
+ * @which:	The property/attribute to be extracted.
+ * @length:	Pointer to length of returned data size (unused if NULL).
+ *
+ * Calls prom.c's get_property() to return the value of the
+ * attribute specified by @which
+*/
+const void *vio_get_attribute(struct vio_dev *vdev, char *which, int *length)
+{
+	return get_property(vdev->dev.platform_data, which, length);
+}
+EXPORT_SYMBOL(vio_get_attribute);
+
+#ifdef CONFIG_PPC_PSERIES
+/* vio_find_name() - internal because only vio.c knows how we formatted the
+ * kobject name
+ * XXX once vio_bus_type.devices is actually used as a kset in
+ * drivers/base/bus.c, this function should be removed in favor of
+ * "device_find(kobj_name, &vio_bus_type)"
+ */
+static struct vio_dev *vio_find_name(const char *kobj_name)
+{
+	struct kobject *found;
+
+	found = kset_find_obj(&devices_subsys.kset, kobj_name);
+	if (!found)
+		return NULL;
+
+	return to_vio_dev(container_of(found, struct device, kobj));
+}
+
+/**
+ * vio_find_node - find an already-registered vio_dev
+ * @vnode: device_node of the virtual device we're looking for
+ */
+struct vio_dev *vio_find_node(struct device_node *vnode)
+{
+	uint32_t *unit_address;
+	char kobj_name[BUS_ID_SIZE];
+
+	/* construct the kobject name from the device node */
+	unit_address = (uint32_t *)get_property(vnode, "reg", NULL);
+	if (!unit_address)
+		return NULL;
+	snprintf(kobj_name, BUS_ID_SIZE, "%x", *unit_address);
+
+	return vio_find_name(kobj_name);
+}
+EXPORT_SYMBOL(vio_find_node);
+
+int vio_enable_interrupts(struct vio_dev *dev)
+{
+	int rc = h_vio_signal(dev->unit_address, VIO_IRQ_ENABLE);
+	if (rc != H_SUCCESS)
+		printk(KERN_ERR "vio: Error 0x%x enabling interrupts\n", rc);
+	return rc;
+}
+EXPORT_SYMBOL(vio_enable_interrupts);
+
+int vio_disable_interrupts(struct vio_dev *dev)
+{
+	int rc = h_vio_signal(dev->unit_address, VIO_IRQ_DISABLE);
+	if (rc != H_SUCCESS)
+		printk(KERN_ERR "vio: Error 0x%x disabling interrupts\n", rc);
+	return rc;
+}
+EXPORT_SYMBOL(vio_disable_interrupts);
+#endif /* CONFIG_PPC_PSERIES */
diff --git a/arch/powerpc/mm/hash_utils_64.c b/arch/powerpc/mm/hash_utils_64.c
index c006d90..b43ed92e 100644
--- a/arch/powerpc/mm/hash_utils_64.c
+++ b/arch/powerpc/mm/hash_utils_64.c
@@ -319,7 +319,7 @@
 		mmu_virtual_psize = MMU_PAGE_64K;
 #endif
 
-	printk(KERN_INFO "Page orders: linear mapping = %d, others = %d\n",
+	printk(KERN_DEBUG "Page orders: linear mapping = %d, others = %d\n",
 	       mmu_psize_defs[mmu_linear_psize].shift,
 	       mmu_psize_defs[mmu_virtual_psize].shift);
 
diff --git a/arch/powerpc/mm/lmb.c b/arch/powerpc/mm/lmb.c
index 417d585..8b6f522 100644
--- a/arch/powerpc/mm/lmb.c
+++ b/arch/powerpc/mm/lmb.c
@@ -89,18 +89,23 @@
 	return lmb_addrs_adjacent(base1, size1, base2, size2);
 }
 
+static void __init lmb_remove_region(struct lmb_region *rgn, unsigned long r)
+{
+	unsigned long i;
+
+	for (i = r; i < rgn->cnt - 1; i++) {
+		rgn->region[i].base = rgn->region[i + 1].base;
+		rgn->region[i].size = rgn->region[i + 1].size;
+	}
+	rgn->cnt--;
+}
+
 /* Assumption: base addr of region 1 < base addr of region 2 */
 static void __init lmb_coalesce_regions(struct lmb_region *rgn,
 		unsigned long r1, unsigned long r2)
 {
-	unsigned long i;
-
 	rgn->region[r1].size += rgn->region[r2].size;
-	for (i=r2; i < rgn->cnt-1; i++) {
-		rgn->region[i].base = rgn->region[i+1].base;
-		rgn->region[i].size = rgn->region[i+1].size;
-	}
-	rgn->cnt--;
+	lmb_remove_region(rgn, r2);
 }
 
 /* This routine called with relocation disabled. */
@@ -294,17 +299,16 @@
 	return (lmb.memory.region[idx].base + lmb.memory.region[idx].size);
 }
 
-/*
- * Truncate the lmb list to memory_limit if it's set
- * You must call lmb_analyze() after this.
- */
+/* You must call lmb_analyze() after this. */
 void __init lmb_enforce_memory_limit(unsigned long memory_limit)
 {
 	unsigned long i, limit;
+	struct lmb_property *p;
 
 	if (! memory_limit)
 		return;
 
+	/* Truncate the lmb regions to satisfy the memory limit. */
 	limit = memory_limit;
 	for (i = 0; i < lmb.memory.cnt; i++) {
 		if (limit > lmb.memory.region[i].size) {
@@ -316,4 +320,21 @@
 		lmb.memory.cnt = i + 1;
 		break;
 	}
+
+	lmb.rmo_size = lmb.memory.region[0].size;
+
+	/* And truncate any reserves above the limit also. */
+	for (i = 0; i < lmb.reserved.cnt; i++) {
+		p = &lmb.reserved.region[i];
+
+		if (p->base > memory_limit)
+			p->size = 0;
+		else if ((p->base + p->size) > memory_limit)
+			p->size = memory_limit - p->base;
+
+		if (p->size == 0) {
+			lmb_remove_region(&lmb.reserved, i);
+			i--;
+		}
+	}
 }
diff --git a/arch/powerpc/mm/mem.c b/arch/powerpc/mm/mem.c
index 741dd88..69f3b9a 100644
--- a/arch/powerpc/mm/mem.c
+++ b/arch/powerpc/mm/mem.c
@@ -299,9 +299,9 @@
 	kmap_prot = PAGE_KERNEL;
 #endif /* CONFIG_HIGHMEM */
 
-	printk(KERN_INFO "Top of RAM: 0x%lx, Total RAM: 0x%lx\n",
+	printk(KERN_DEBUG "Top of RAM: 0x%lx, Total RAM: 0x%lx\n",
 	       top_of_ram, total_ram);
-	printk(KERN_INFO "Memory hole size: %ldMB\n",
+	printk(KERN_DEBUG "Memory hole size: %ldMB\n",
 	       (top_of_ram - total_ram) >> 20);
 	/*
 	 * All pages are DMA-able so we put them all in the DMA zone.
@@ -380,7 +380,7 @@
 			totalhigh_pages++;
 		}
 		totalram_pages += totalhigh_pages;
-		printk(KERN_INFO "High memory: %luk\n",
+		printk(KERN_DEBUG "High memory: %luk\n",
 		       totalhigh_pages << (PAGE_SHIFT-10));
 	}
 #endif /* CONFIG_HIGHMEM */
diff --git a/arch/powerpc/mm/numa.c b/arch/powerpc/mm/numa.c
index 092355f..aa98cb3 100644
--- a/arch/powerpc/mm/numa.c
+++ b/arch/powerpc/mm/numa.c
@@ -487,9 +487,9 @@
 	unsigned long total_ram = lmb_phys_mem_size();
 	unsigned int i;
 
-	printk(KERN_INFO "Top of RAM: 0x%lx, Total RAM: 0x%lx\n",
+	printk(KERN_DEBUG "Top of RAM: 0x%lx, Total RAM: 0x%lx\n",
 	       top_of_ram, total_ram);
-	printk(KERN_INFO "Memory hole size: %ldMB\n",
+	printk(KERN_DEBUG "Memory hole size: %ldMB\n",
 	       (top_of_ram - total_ram) >> 20);
 
 	for (i = 0; i < lmb.memory.cnt; ++i)
@@ -507,7 +507,7 @@
 		return;
 
 	for_each_online_node(node) {
-		printk(KERN_INFO "Node %d CPUs:", node);
+		printk(KERN_DEBUG "Node %d CPUs:", node);
 
 		count = 0;
 		/*
@@ -543,7 +543,7 @@
 	for_each_online_node(node) {
 		unsigned long i;
 
-		printk(KERN_INFO "Node %d Memory:", node);
+		printk(KERN_DEBUG "Node %d Memory:", node);
 
 		count = 0;
 
diff --git a/arch/powerpc/oprofile/common.c b/arch/powerpc/oprofile/common.c
index 5b1de7e..38a2f9c 100644
--- a/arch/powerpc/oprofile/common.c
+++ b/arch/powerpc/oprofile/common.c
@@ -162,7 +162,7 @@
 	ops->stop = op_powerpc_stop;
 	ops->backtrace = op_powerpc_backtrace;
 
-	printk(KERN_INFO "oprofile: using %s performance monitoring.\n",
+	printk(KERN_DEBUG "oprofile: using %s performance monitoring.\n",
 	       ops->cpu_type);
 
 	return 0;
diff --git a/arch/powerpc/platforms/85xx/Kconfig b/arch/powerpc/platforms/85xx/Kconfig
index 06e3712..454fc53 100644
--- a/arch/powerpc/platforms/85xx/Kconfig
+++ b/arch/powerpc/platforms/85xx/Kconfig
@@ -11,13 +11,20 @@
 	help
 	  This option enables support for the MPC 8540 ADS board
 
+config MPC85xx_CDS
+	bool "Freescale MPC85xx CDS"
+	select DEFAULT_UIMAGE
+	select PPC_I8259 if PCI
+	help
+	  This option enables support for the MPC85xx CDS board
+
 endchoice
 
 config MPC8540
 	bool
 	select PPC_UDBG_16550
 	select PPC_INDIRECT_PCI
-	default y if MPC8540_ADS
+	default y if MPC8540_ADS || MPC85xx_CDS
 
 config PPC_INDIRECT_PCI_BE
 	bool
diff --git a/arch/powerpc/platforms/85xx/Makefile b/arch/powerpc/platforms/85xx/Makefile
index ffc4139..7615aa5 100644
--- a/arch/powerpc/platforms/85xx/Makefile
+++ b/arch/powerpc/platforms/85xx/Makefile
@@ -3,3 +3,4 @@
 #
 obj-$(CONFIG_PPC_85xx)	+= misc.o pci.o
 obj-$(CONFIG_MPC8540_ADS) += mpc85xx_ads.o
+obj-$(CONFIG_MPC85xx_CDS) += mpc85xx_cds.o
diff --git a/arch/powerpc/platforms/85xx/mpc85xx_cds.c b/arch/powerpc/platforms/85xx/mpc85xx_cds.c
new file mode 100644
index 0000000..18e6e11
--- /dev/null
+++ b/arch/powerpc/platforms/85xx/mpc85xx_cds.c
@@ -0,0 +1,359 @@
+/*
+ * MPC85xx setup and early boot code plus other random bits.
+ *
+ * Maintained by Kumar Gala (see MAINTAINERS for contact information)
+ *
+ * Copyright 2005 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/config.h>
+#include <linux/stddef.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/errno.h>
+#include <linux/reboot.h>
+#include <linux/pci.h>
+#include <linux/kdev_t.h>
+#include <linux/major.h>
+#include <linux/console.h>
+#include <linux/delay.h>
+#include <linux/seq_file.h>
+#include <linux/root_dev.h>
+#include <linux/initrd.h>
+#include <linux/module.h>
+#include <linux/fsl_devices.h>
+
+#include <asm/system.h>
+#include <asm/pgtable.h>
+#include <asm/page.h>
+#include <asm/atomic.h>
+#include <asm/time.h>
+#include <asm/io.h>
+#include <asm/machdep.h>
+#include <asm/ipic.h>
+#include <asm/bootinfo.h>
+#include <asm/pci-bridge.h>
+#include <asm/mpc85xx.h>
+#include <asm/irq.h>
+#include <mm/mmu_decl.h>
+#include <asm/prom.h>
+#include <asm/udbg.h>
+#include <asm/mpic.h>
+#include <asm/i8259.h>
+
+#include <sysdev/fsl_soc.h>
+#include "mpc85xx.h"
+
+#ifndef CONFIG_PCI
+unsigned long isa_io_base = 0;
+unsigned long isa_mem_base = 0;
+#endif
+
+static int cds_pci_slot = 2;
+static volatile u8 *cadmus;
+
+/*
+ * Internal interrupts are all Level Sensitive, and Positive Polarity
+ *
+ * Note:  Likely, this table and the following function should be
+ *        obtained and derived from the OF Device Tree.
+ */
+static u_char mpc85xx_cds_openpic_initsenses[] __initdata = {
+	MPC85XX_INTERNAL_IRQ_SENSES,
+#if defined(CONFIG_PCI)
+	(IRQ_SENSE_LEVEL | IRQ_POLARITY_POSITIVE),	/* Ext 0: PCI slot 0 */
+	(IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE),	/* Ext 1: PCI slot 1 */
+	(IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE),	/* Ext 2: PCI slot 2 */
+	(IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE),	/* Ext 3: PCI slot 3 */
+#else
+	0x0,				/* External  0: */
+	0x0,				/* External  1: */
+	0x0,				/* External  2: */
+	0x0,				/* External  3: */
+#endif
+	(IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE),	/* External 5: PHY */
+	0x0,				/* External  6: */
+	0x0,				/* External  7: */
+	0x0,				/* External  8: */
+	0x0,				/* External  9: */
+	0x0,				/* External 10: */
+#ifdef CONFIG_PCI
+	(IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE),    /* Ext 11: PCI2 slot 0 */
+#else
+	0x0,				/* External 11: */
+#endif
+};
+
+
+#ifdef CONFIG_PCI
+/*
+ * interrupt routing
+ */
+int
+mpc85xx_map_irq(struct pci_dev *dev, unsigned char idsel, unsigned char pin)
+{
+	struct pci_controller *hose = pci_bus_to_hose(dev->bus->number);
+
+	if (!hose->index)
+	{
+		/* Handle PCI1 interrupts */
+		char pci_irq_table[][4] =
+			/*
+			 *      PCI IDSEL/INTPIN->INTLINE
+			 *        A      B      C      D
+			 */
+
+			/* Note IRQ assignment for slots is based on which slot the elysium is
+			 * in -- in this setup elysium is in slot #2 (this PIRQA as first
+			 * interrupt on slot */
+		{
+			{ 0, 1, 2, 3 }, /* 16 - PMC */
+			{ 0, 1, 2, 3 }, /* 17 P2P (Tsi320) */
+			{ 0, 1, 2, 3 }, /* 18 - Slot 1 */
+			{ 1, 2, 3, 0 }, /* 19 - Slot 2 */
+			{ 2, 3, 0, 1 }, /* 20 - Slot 3 */
+			{ 3, 0, 1, 2 }, /* 21 - Slot 4 */
+		};
+
+		const long min_idsel = 16, max_idsel = 21, irqs_per_slot = 4;
+		int i, j;
+
+		for (i = 0; i < 6; i++)
+			for (j = 0; j < 4; j++)
+				pci_irq_table[i][j] =
+					((pci_irq_table[i][j] + 5 -
+					  cds_pci_slot) & 0x3) + PIRQ0A;
+
+		return PCI_IRQ_TABLE_LOOKUP;
+	} else {
+		/* Handle PCI2 interrupts (if we have one) */
+		char pci_irq_table[][4] =
+		{
+			/*
+			 * We only have one slot and one interrupt
+			 * going to PIRQA - PIRQD */
+			{ PIRQ1A, PIRQ1A, PIRQ1A, PIRQ1A }, /* 21 - slot 0 */
+		};
+
+		const long min_idsel = 21, max_idsel = 21, irqs_per_slot = 4;
+
+		return PCI_IRQ_TABLE_LOOKUP;
+	}
+}
+
+#define ARCADIA_HOST_BRIDGE_IDSEL	17
+#define ARCADIA_2ND_BRIDGE_IDSEL	3
+
+extern int mpc85xx_pci2_busno;
+
+int
+mpc85xx_exclude_device(u_char bus, u_char devfn)
+{
+	if (bus == 0 && PCI_SLOT(devfn) == 0)
+		return PCIBIOS_DEVICE_NOT_FOUND;
+	if (mpc85xx_pci2_busno)
+		if (bus == (mpc85xx_pci2_busno) && PCI_SLOT(devfn) == 0)
+			return PCIBIOS_DEVICE_NOT_FOUND;
+	/* We explicitly do not go past the Tundra 320 Bridge */
+	if ((bus == 1) && (PCI_SLOT(devfn) == ARCADIA_2ND_BRIDGE_IDSEL))
+		return PCIBIOS_DEVICE_NOT_FOUND;
+	if ((bus == 0) && (PCI_SLOT(devfn) == ARCADIA_2ND_BRIDGE_IDSEL))
+		return PCIBIOS_DEVICE_NOT_FOUND;
+	else
+		return PCIBIOS_SUCCESSFUL;
+}
+
+void __init
+mpc85xx_cds_pcibios_fixup(void)
+{
+	struct pci_dev *dev;
+	u_char		c;
+
+	if ((dev = pci_get_device(PCI_VENDOR_ID_VIA,
+					PCI_DEVICE_ID_VIA_82C586_1, NULL))) {
+		/*
+		 * U-Boot does not set the enable bits
+		 * for the IDE device. Force them on here.
+		 */
+		pci_read_config_byte(dev, 0x40, &c);
+		c |= 0x03; /* IDE: Chip Enable Bits */
+		pci_write_config_byte(dev, 0x40, c);
+
+		/*
+		 * Since only primary interface works, force the
+		 * IDE function to standard primary IDE interrupt
+		 * w/ 8259 offset
+		 */
+		dev->irq = 14;
+		pci_write_config_byte(dev, PCI_INTERRUPT_LINE, dev->irq);
+		pci_dev_put(dev);
+	}
+
+	/*
+	 * Force legacy USB interrupt routing
+	 */
+	if ((dev = pci_get_device(PCI_VENDOR_ID_VIA,
+					PCI_DEVICE_ID_VIA_82C586_2, NULL))) {
+		dev->irq = 10;
+		pci_write_config_byte(dev, PCI_INTERRUPT_LINE, 10);
+		pci_dev_put(dev);
+	}
+
+	if ((dev = pci_get_device(PCI_VENDOR_ID_VIA,
+					PCI_DEVICE_ID_VIA_82C586_2, dev))) {
+		dev->irq = 11;
+		pci_write_config_byte(dev, PCI_INTERRUPT_LINE, 11);
+		pci_dev_put(dev);
+	}
+}
+#endif /* CONFIG_PCI */
+
+void __init mpc85xx_cds_pic_init(void)
+{
+	struct mpic *mpic1;
+	phys_addr_t OpenPIC_PAddr;
+
+	/* Determine the Physical Address of the OpenPIC regs */
+	OpenPIC_PAddr = get_immrbase() + MPC85xx_OPENPIC_OFFSET;
+
+	mpic1 = mpic_alloc(OpenPIC_PAddr,
+			MPIC_PRIMARY | MPIC_WANTS_RESET | MPIC_BIG_ENDIAN,
+			4, MPC85xx_OPENPIC_IRQ_OFFSET, 0, 250,
+			mpc85xx_cds_openpic_initsenses,
+			sizeof(mpc85xx_cds_openpic_initsenses), " OpenPIC  ");
+	BUG_ON(mpic1 == NULL);
+	mpic_assign_isu(mpic1, 0, OpenPIC_PAddr + 0x10200);
+	mpic_assign_isu(mpic1, 1, OpenPIC_PAddr + 0x10280);
+	mpic_assign_isu(mpic1, 2, OpenPIC_PAddr + 0x10300);
+	mpic_assign_isu(mpic1, 3, OpenPIC_PAddr + 0x10380);
+	mpic_assign_isu(mpic1, 4, OpenPIC_PAddr + 0x10400);
+	mpic_assign_isu(mpic1, 5, OpenPIC_PAddr + 0x10480);
+	mpic_assign_isu(mpic1, 6, OpenPIC_PAddr + 0x10500);
+	mpic_assign_isu(mpic1, 7, OpenPIC_PAddr + 0x10580);
+
+	/* dummy mappings to get to 48 */
+	mpic_assign_isu(mpic1, 8, OpenPIC_PAddr + 0x10600);
+	mpic_assign_isu(mpic1, 9, OpenPIC_PAddr + 0x10680);
+	mpic_assign_isu(mpic1, 10, OpenPIC_PAddr + 0x10700);
+	mpic_assign_isu(mpic1, 11, OpenPIC_PAddr + 0x10780);
+
+	/* External ints */
+	mpic_assign_isu(mpic1, 12, OpenPIC_PAddr + 0x10000);
+	mpic_assign_isu(mpic1, 13, OpenPIC_PAddr + 0x10080);
+	mpic_assign_isu(mpic1, 14, OpenPIC_PAddr + 0x10100);
+
+	mpic_init(mpic1);
+
+#ifdef CONFIG_PCI
+	mpic_setup_cascade(PIRQ0A, i8259_irq_cascade, NULL);
+
+	i8259_init(0,0);
+#endif
+}
+
+
+/*
+ * Setup the architecture
+ */
+static void __init
+mpc85xx_cds_setup_arch(void)
+{
+	struct device_node *cpu;
+#ifdef CONFIG_PCI
+	struct device_node *np;
+#endif
+
+	if (ppc_md.progress)
+		ppc_md.progress("mpc85xx_cds_setup_arch()", 0);
+
+	cpu = of_find_node_by_type(NULL, "cpu");
+	if (cpu != 0) {
+		unsigned int *fp;
+
+		fp = (int *)get_property(cpu, "clock-frequency", NULL);
+		if (fp != 0)
+			loops_per_jiffy = *fp / HZ;
+		else
+			loops_per_jiffy = 500000000 / HZ;
+		of_node_put(cpu);
+	}
+
+	cadmus = ioremap(CADMUS_BASE, CADMUS_SIZE);
+	cds_pci_slot = ((cadmus[CM_CSR] >> 6) & 0x3) + 1;
+
+	if (ppc_md.progress) {
+		char buf[40];
+		snprintf(buf, 40, "CDS Version = 0x%x in slot %d\n",
+				cadmus[CM_VER], cds_pci_slot);
+		ppc_md.progress(buf, 0);
+	}
+
+#ifdef CONFIG_PCI
+	for (np = NULL; (np = of_find_node_by_type(np, "pci")) != NULL;)
+		add_bridge(np);
+
+	ppc_md.pcibios_fixup = mpc85xx_cds_pcibios_fixup;
+	ppc_md.pci_swizzle = common_swizzle;
+	ppc_md.pci_map_irq = mpc85xx_map_irq;
+	ppc_md.pci_exclude_device = mpc85xx_exclude_device;
+#endif
+
+#ifdef  CONFIG_ROOT_NFS
+	ROOT_DEV = Root_NFS;
+#else
+	ROOT_DEV = Root_HDA1;
+#endif
+}
+
+
+void
+mpc85xx_cds_show_cpuinfo(struct seq_file *m)
+{
+	uint pvid, svid, phid1;
+	uint memsize = total_memory;
+
+	pvid = mfspr(SPRN_PVR);
+	svid = mfspr(SPRN_SVR);
+
+	seq_printf(m, "Vendor\t\t: Freescale Semiconductor\n");
+	seq_printf(m, "Machine\t\t: MPC85xx CDS (0x%x)\n", cadmus[CM_VER]);
+	seq_printf(m, "PVR\t\t: 0x%x\n", pvid);
+	seq_printf(m, "SVR\t\t: 0x%x\n", svid);
+
+	/* Display cpu Pll setting */
+	phid1 = mfspr(SPRN_HID1);
+	seq_printf(m, "PLL setting\t: 0x%x\n", ((phid1 >> 24) & 0x3f));
+
+	/* Display the amount of memory */
+	seq_printf(m, "Memory\t\t: %d MB\n", memsize / (1024 * 1024));
+}
+
+
+/*
+ * Called very early, device-tree isn't unflattened
+ */
+static int __init mpc85xx_cds_probe(void)
+{
+	/* We always match for now, eventually we should look at
+	 * the flat dev tree to ensure this is the board we are
+	 * supposed to run on
+	 */
+	return 1;
+}
+
+define_machine(mpc85xx_cds) {
+	.name		= "MPC85xx CDS",
+	.probe		= mpc85xx_cds_probe,
+	.setup_arch	= mpc85xx_cds_setup_arch,
+	.init_IRQ	= mpc85xx_cds_pic_init,
+	.show_cpuinfo	= mpc85xx_cds_show_cpuinfo,
+	.get_irq	= mpic_get_irq,
+	.restart	= mpc85xx_restart,
+	.calibrate_decr = generic_calibrate_decr,
+	.progress	= udbg_progress,
+};
diff --git a/arch/powerpc/platforms/85xx/mpc85xx_cds.h b/arch/powerpc/platforms/85xx/mpc85xx_cds.h
new file mode 100644
index 0000000..671f54f
--- /dev/null
+++ b/arch/powerpc/platforms/85xx/mpc85xx_cds.h
@@ -0,0 +1,43 @@
+/*
+ * arch/ppc/platforms/85xx/mpc85xx_cds_common.h
+ *
+ * MPC85xx CDS board definitions
+ *
+ * Maintainer: Kumar Gala <galak@kernel.crashing.org>
+ *
+ * Copyright 2004 Freescale Semiconductor, Inc
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ *
+ */
+
+#ifndef __MACH_MPC85XX_CDS_H__
+#define __MACH_MPC85XX_CDS_H__
+
+/* CADMUS info */
+#define CADMUS_BASE (0xf8004000)
+#define CADMUS_SIZE (256)
+#define CM_VER	(0)
+#define CM_CSR	(1)
+#define CM_RST	(2)
+
+/* CDS NVRAM/RTC */
+#define CDS_RTC_ADDR	(0xf8000000)
+#define CDS_RTC_SIZE	(8 * 1024)
+
+/* PCI interrupt controller */
+#define PIRQ0A			MPC85xx_IRQ_EXT0
+#define PIRQ0B			MPC85xx_IRQ_EXT1
+#define PIRQ0C			MPC85xx_IRQ_EXT2
+#define PIRQ0D			MPC85xx_IRQ_EXT3
+#define PIRQ1A			MPC85xx_IRQ_EXT11
+
+#define NR_8259_INTS		16
+#define CPM_IRQ_OFFSET		NR_8259_INTS
+
+#define MPC85xx_OPENPIC_IRQ_OFFSET	80
+
+#endif /* __MACH_MPC85XX_CDS_H__ */
diff --git a/arch/powerpc/platforms/cell/spufs/context.c b/arch/powerpc/platforms/cell/spufs/context.c
index 8bb33ab..36439c5 100644
--- a/arch/powerpc/platforms/cell/spufs/context.c
+++ b/arch/powerpc/platforms/cell/spufs/context.c
@@ -30,7 +30,7 @@
 struct spu_context *alloc_spu_context(void)
 {
 	struct spu_context *ctx;
-	ctx = kmalloc(sizeof *ctx, GFP_KERNEL);
+	ctx = kzalloc(sizeof *ctx, GFP_KERNEL);
 	if (!ctx)
 		goto out;
 	/* Binding to physical processor deferred
@@ -48,17 +48,7 @@
 	init_waitqueue_head(&ctx->wbox_wq);
 	init_waitqueue_head(&ctx->stop_wq);
 	init_waitqueue_head(&ctx->mfc_wq);
-	ctx->ibox_fasync = NULL;
-	ctx->wbox_fasync = NULL;
-	ctx->mfc_fasync = NULL;
-	ctx->mfc = NULL;
-	ctx->tagwait = 0;
 	ctx->state = SPU_STATE_SAVED;
-	ctx->local_store = NULL;
-	ctx->cntl = NULL;
-	ctx->signal1 = NULL;
-	ctx->signal2 = NULL;
-	ctx->spu = NULL;
 	ctx->ops = &spu_backing_ops;
 	ctx->owner = get_task_mm(current);
 	goto out;
diff --git a/arch/powerpc/platforms/iseries/Makefile b/arch/powerpc/platforms/iseries/Makefile
index ce8c0b9..7e67a20 100644
--- a/arch/powerpc/platforms/iseries/Makefile
+++ b/arch/powerpc/platforms/iseries/Makefile
@@ -3,7 +3,6 @@
 obj-y += hvlog.o hvlpconfig.o lpardata.o setup.o mf.o lpevents.o \
 	hvcall.o proc.o htab.o iommu.o misc.o irq.o
 obj-$(CONFIG_PCI) += pci.o vpdinfo.o
-obj-$(CONFIG_IBMVIO) += vio.o
 obj-$(CONFIG_SMP) += smp.o
 obj-$(CONFIG_VIOPATH) += viopath.o
 obj-$(CONFIG_MODULES) += ksyms.o
diff --git a/arch/powerpc/platforms/iseries/iommu.c b/arch/powerpc/platforms/iseries/iommu.c
index bea0b70..3ac2206 100644
--- a/arch/powerpc/platforms/iseries/iommu.c
+++ b/arch/powerpc/platforms/iseries/iommu.c
@@ -4,6 +4,7 @@
  * Rewrite, cleanup:
  *
  * Copyright (C) 2004 Olof Johansson <olof@lixom.net>, IBM Corporation
+ * Copyright (C) 2006 Olof Johansson <olof@lixom.net>
  *
  * Dynamic DMA mapping support, iSeries-specific parts.
  *
@@ -33,8 +34,7 @@
 #include <asm/abs_addr.h>
 #include <asm/pci-bridge.h>
 #include <asm/iseries/hv_call_xm.h>
-
-#include "iommu.h"
+#include <asm/iseries/iommu.h>
 
 extern struct list_head iSeries_Global_Device_List;
 
@@ -43,30 +43,28 @@
 		unsigned long uaddr, enum dma_data_direction direction)
 {
 	u64 rc;
-	union tce_entry tce;
+	u64 tce, rpn;
 
 	index <<= TCE_PAGE_FACTOR;
 	npages <<= TCE_PAGE_FACTOR;
 
 	while (npages--) {
-		tce.te_word = 0;
-		tce.te_bits.tb_rpn = virt_to_abs(uaddr) >> TCE_SHIFT;
+		rpn = virt_to_abs(uaddr) >> TCE_SHIFT;
+		tce = (rpn & TCE_RPN_MASK) << TCE_RPN_SHIFT;
 
 		if (tbl->it_type == TCE_VB) {
 			/* Virtual Bus */
-			tce.te_bits.tb_valid = 1;
-			tce.te_bits.tb_allio = 1;
+			tce |= TCE_VALID|TCE_ALLIO;
 			if (direction != DMA_TO_DEVICE)
-				tce.te_bits.tb_rdwr = 1;
+				tce |= TCE_VB_WRITE;
 		} else {
 			/* PCI Bus */
-			tce.te_bits.tb_rdwr = 1; /* Read allowed */
+			tce |= TCE_PCI_READ; /* Read allowed */
 			if (direction != DMA_TO_DEVICE)
-				tce.te_bits.tb_pciwr = 1;
+				tce |= TCE_PCI_WRITE;
 		}
 
-		rc = HvCallXm_setTce((u64)tbl->it_index, (u64)index,
-				tce.te_word);
+		rc = HvCallXm_setTce((u64)tbl->it_index, (u64)index, tce);
 		if (rc)
 			panic("PCI_DMA: HvCallXm_setTce failed, Rc: 0x%lx\n",
 					rc);
@@ -124,7 +122,7 @@
 
 	/* itc_size is in pages worth of table, it_size is in # of entries */
 	tbl->it_size = ((parms->itc_size * TCE_PAGE_SIZE) /
-			sizeof(union tce_entry)) >> TCE_PAGE_FACTOR;
+			TCE_ENTRY_SIZE) >> TCE_PAGE_FACTOR;
 	tbl->it_busno = parms->itc_busno;
 	tbl->it_offset = parms->itc_offset >> TCE_PAGE_FACTOR;
 	tbl->it_index = parms->itc_index;
diff --git a/arch/powerpc/platforms/iseries/mf.c b/arch/powerpc/platforms/iseries/mf.c
index d771b8e..1a2c2a5 100644
--- a/arch/powerpc/platforms/iseries/mf.c
+++ b/arch/powerpc/platforms/iseries/mf.c
@@ -45,7 +45,6 @@
 
 #include "setup.h"
 
-extern int piranha_simulator;
 static int mf_initialized;
 
 /*
@@ -658,7 +657,7 @@
 
 void __init mf_display_progress(u16 value)
 {
-	if (piranha_simulator || !mf_initialized)
+	if (!mf_initialized)
 		return;
 
 	if (0xFFFF == value)
@@ -1295,9 +1294,6 @@
  */
 void iSeries_get_rtc_time(struct rtc_time *rtc_tm)
 {
-	if (piranha_simulator)
-		return;
-
 	mf_get_rtc(rtc_tm);
 	rtc_tm->tm_mon--;
 }
@@ -1316,9 +1312,6 @@
 {
 	struct rtc_time tm;
 
-	if (piranha_simulator)
-		return 0;
-
 	mf_get_boot_rtc(&tm);
 	return mktime(tm.tm_year + 1900, tm.tm_mon, tm.tm_mday,
 		      tm.tm_hour, tm.tm_min, tm.tm_sec);
diff --git a/arch/powerpc/platforms/iseries/pci.c b/arch/powerpc/platforms/iseries/pci.c
index a19833b..428ffb5 100644
--- a/arch/powerpc/platforms/iseries/pci.c
+++ b/arch/powerpc/platforms/iseries/pci.c
@@ -37,15 +37,13 @@
 
 #include <asm/iseries/hv_call_xm.h>
 #include <asm/iseries/mf.h>
+#include <asm/iseries/iommu.h>
 
 #include <asm/ppc-pci.h>
 
 #include "irq.h"
 #include "pci.h"
 #include "call_pci.h"
-#include "iommu.h"
-
-extern unsigned long io_page_mask;
 
 /*
  * Forward declares of prototypes.
@@ -277,7 +275,6 @@
 {
 	iomm_table_initialize();
 	find_and_init_phbs();
-	io_page_mask = -1;
 }
 
 /*
diff --git a/arch/powerpc/platforms/iseries/setup.c b/arch/powerpc/platforms/iseries/setup.c
index a6fd9be..fd6d0eb 100644
--- a/arch/powerpc/platforms/iseries/setup.c
+++ b/arch/powerpc/platforms/iseries/setup.c
@@ -28,6 +28,7 @@
 #include <linux/major.h>
 #include <linux/root_dev.h>
 #include <linux/kernel.h>
+#include <linux/if_ether.h>	/* ETH_ALEN */
 
 #include <asm/processor.h>
 #include <asm/machdep.h>
@@ -45,6 +46,7 @@
 #include <asm/cache.h>
 #include <asm/sections.h>
 #include <asm/abs_addr.h>
+#include <asm/iseries/hv_types.h>
 #include <asm/iseries/hv_lp_config.h>
 #include <asm/iseries/hv_call_event.h>
 #include <asm/iseries/hv_call_xm.h>
@@ -81,9 +83,6 @@
 static void iSeries_pci_final_fixup(void) { }
 #endif
 
-/* Global Variables */
-int piranha_simulator;
-
 extern int rd_size;		/* Defined in drivers/block/rd.c */
 extern unsigned long embedded_sysmap_start;
 extern unsigned long embedded_sysmap_end;
@@ -91,8 +90,6 @@
 extern unsigned long iSeries_recal_tb;
 extern unsigned long iSeries_recal_titan;
 
-static unsigned long cmd_mem_limit;
-
 struct MemoryBlock {
 	unsigned long absStart;
 	unsigned long absEnd;
@@ -340,8 +337,6 @@
 #ifdef CONFIG_SMP
 	smp_init_iSeries();
 #endif
-	if (itLpNaca.xPirEnvironMode == 0)
-		piranha_simulator = 1;
 
 	/* Associate Lp Event Queue 0 with processor 0 */
 	HvCallEvent_setLpEventQueueInterruptProc(0, 0);
@@ -536,10 +531,10 @@
 {
 	if (get_lppaca()->shared_proc) {
 		ppc_md.idle_loop = iseries_shared_idle;
-		printk(KERN_INFO "Using shared processor idle loop\n");
+		printk(KERN_DEBUG "Using shared processor idle loop\n");
 	} else {
 		ppc_md.idle_loop = iseries_dedicated_idle;
-		printk(KERN_INFO "Using dedicated idle loop\n");
+		printk(KERN_DEBUG "Using dedicated idle loop\n");
 	}
 
 	/* Setup the Lp Event Queue */
@@ -715,7 +710,7 @@
 };
 
 struct blob {
-	unsigned char data[PAGE_SIZE];
+	unsigned char data[PAGE_SIZE * 2];
 	unsigned long next;
 };
 
@@ -916,6 +911,95 @@
 	dt_prop_str(dt, "compatible", "IBM,iSeries");
 }
 
+void dt_vdevices(struct iseries_flat_dt *dt)
+{
+	u32 reg = 0;
+	HvLpIndexMap vlan_map;
+	int i;
+	char buf[32];
+
+	dt_start_node(dt, "vdevice");
+	dt_prop_str(dt, "device_type", "vdevice");
+	dt_prop_str(dt, "compatible", "IBM,iSeries-vdevice");
+	dt_prop_u32(dt, "#address-cells", 1);
+	dt_prop_u32(dt, "#size-cells", 0);
+
+	snprintf(buf, sizeof(buf), "vty@%08x", reg);
+	dt_start_node(dt, buf);
+	dt_prop_str(dt, "device_type", "serial");
+	dt_prop_u32(dt, "reg", reg);
+	dt_end_node(dt);
+	reg++;
+
+	snprintf(buf, sizeof(buf), "v-scsi@%08x", reg);
+	dt_start_node(dt, buf);
+	dt_prop_str(dt, "device_type", "vscsi");
+	dt_prop_str(dt, "compatible", "IBM,v-scsi");
+	dt_prop_u32(dt, "reg", reg);
+	dt_end_node(dt);
+	reg++;
+
+	vlan_map = HvLpConfig_getVirtualLanIndexMap();
+	for (i = 0; i < HVMAXARCHITECTEDVIRTUALLANS; i++) {
+		unsigned char mac_addr[ETH_ALEN];
+
+		if ((vlan_map & (0x8000 >> i)) == 0)
+			continue;
+		snprintf(buf, 32, "l-lan@%08x", reg + i);
+		dt_start_node(dt, buf);
+		dt_prop_str(dt, "device_type", "network");
+		dt_prop_str(dt, "compatible", "IBM,iSeries-l-lan");
+		dt_prop_u32(dt, "reg", reg + i);
+		dt_prop_u32(dt, "linux,unit_address", i);
+
+		mac_addr[0] = 0x02;
+		mac_addr[1] = 0x01;
+		mac_addr[2] = 0xff;
+		mac_addr[3] = i;
+		mac_addr[4] = 0xff;
+		mac_addr[5] = HvLpConfig_getLpIndex_outline();
+		dt_prop(dt, "local-mac-address", (char *)mac_addr, ETH_ALEN);
+		dt_prop(dt, "mac-address", (char *)mac_addr, ETH_ALEN);
+		dt_prop_u32(dt, "max-frame-size", 9000);
+		dt_prop_u32(dt, "address-bits", 48);
+
+		dt_end_node(dt);
+	}
+	reg += HVMAXARCHITECTEDVIRTUALLANS;
+
+	for (i = 0; i < HVMAXARCHITECTEDVIRTUALDISKS; i++) {
+		snprintf(buf, 32, "viodasd@%08x", reg + i);
+		dt_start_node(dt, buf);
+		dt_prop_str(dt, "device_type", "block");
+		dt_prop_str(dt, "compatible", "IBM,iSeries-viodasd");
+		dt_prop_u32(dt, "reg", reg + i);
+		dt_prop_u32(dt, "linux,unit_address", i);
+		dt_end_node(dt);
+	}
+	reg += HVMAXARCHITECTEDVIRTUALDISKS;
+	for (i = 0; i < HVMAXARCHITECTEDVIRTUALCDROMS; i++) {
+		snprintf(buf, 32, "viocd@%08x", reg + i);
+		dt_start_node(dt, buf);
+		dt_prop_str(dt, "device_type", "block");
+		dt_prop_str(dt, "compatible", "IBM,iSeries-viocd");
+		dt_prop_u32(dt, "reg", reg + i);
+		dt_prop_u32(dt, "linux,unit_address", i);
+		dt_end_node(dt);
+	}
+	reg += HVMAXARCHITECTEDVIRTUALCDROMS;
+	for (i = 0; i < HVMAXARCHITECTEDVIRTUALTAPES; i++) {
+		snprintf(buf, 32, "viotape@%08x", reg + i);
+		dt_start_node(dt, buf);
+		dt_prop_str(dt, "device_type", "byte");
+		dt_prop_str(dt, "compatible", "IBM,iSeries-viotape");
+		dt_prop_u32(dt, "reg", reg + i);
+		dt_prop_u32(dt, "linux,unit_address", i);
+		dt_end_node(dt);
+	}
+
+	dt_end_node(dt);
+}
+
 void build_flat_dt(struct iseries_flat_dt *dt, unsigned long phys_mem_size)
 {
 	u64 tmp[2];
@@ -940,12 +1024,12 @@
 	/* /chosen */
 	dt_start_node(dt, "chosen");
 	dt_prop_str(dt, "bootargs", cmd_line);
-	if (cmd_mem_limit)
-		dt_prop_u64(dt, "linux,memory-limit", cmd_mem_limit);
 	dt_end_node(dt);
 
 	dt_cpus(dt);
 
+	dt_vdevices(dt);
+
 	dt_end_node(dt);
 
 	dt_push_u32(dt, OF_DT_END);
@@ -965,29 +1049,11 @@
 
 	iSeries_get_cmdline();
 
-	/* Save unparsed command line copy for /proc/cmdline */
-	strlcpy(saved_command_line, cmd_line, COMMAND_LINE_SIZE);
-
-	/* Parse early parameters, in particular mem=x */
-	parse_early_param();
-
 	build_flat_dt(&iseries_dt, phys_mem_size);
 
 	return (void *) __pa(&iseries_dt);
 }
 
-/*
- * On iSeries we just parse the mem=X option from the command line.
- * On pSeries it's a bit more complicated, see prom_init_mem()
- */
-static int __init early_parsemem(char *p)
-{
-	if (p)
-		cmd_mem_limit = ALIGN(memparse(p, &p), PAGE_SIZE);
-	return 0;
-}
-early_param("mem", early_parsemem);
-
 static void hvputc(char c)
 {
 	if (c == '\n')
diff --git a/arch/powerpc/platforms/iseries/vio.c b/arch/powerpc/platforms/iseries/vio.c
deleted file mode 100644
index ad36ab0..0000000
--- a/arch/powerpc/platforms/iseries/vio.c
+++ /dev/null
@@ -1,131 +0,0 @@
-/*
- * IBM PowerPC iSeries Virtual I/O Infrastructure Support.
- *
- *    Copyright (c) 2005 Stephen Rothwell, IBM Corp.
- *
- *      This program is free software; you can redistribute it and/or
- *      modify it under the terms of the GNU General Public License
- *      as published by the Free Software Foundation; either version
- *      2 of the License, or (at your option) any later version.
- */
-#include <linux/types.h>
-#include <linux/device.h>
-#include <linux/init.h>
-
-#include <asm/vio.h>
-#include <asm/iommu.h>
-#include <asm/tce.h>
-#include <asm/abs_addr.h>
-#include <asm/page.h>
-#include <asm/iseries/vio.h>
-#include <asm/iseries/hv_types.h>
-#include <asm/iseries/hv_lp_config.h>
-#include <asm/iseries/hv_call_xm.h>
-
-#include "iommu.h"
-
-struct device *iSeries_vio_dev = &vio_bus_device.dev;
-EXPORT_SYMBOL(iSeries_vio_dev);
-
-static struct iommu_table veth_iommu_table;
-static struct iommu_table vio_iommu_table;
-
-static void __init iommu_vio_init(void)
-{
-	iommu_table_getparms_iSeries(255, 0, 0xff, &veth_iommu_table);
-	veth_iommu_table.it_size /= 2;
-	vio_iommu_table = veth_iommu_table;
-	vio_iommu_table.it_offset += veth_iommu_table.it_size;
-
-	if (!iommu_init_table(&veth_iommu_table))
-		printk("Virtual Bus VETH TCE table failed.\n");
-	if (!iommu_init_table(&vio_iommu_table))
-		printk("Virtual Bus VIO TCE table failed.\n");
-}
-
-/**
- * vio_register_device_iseries: - Register a new iSeries vio device.
- * @voidev:	The device to register.
- */
-static struct vio_dev *__init vio_register_device_iseries(char *type,
-		uint32_t unit_num)
-{
-	struct vio_dev *viodev;
-
-	/* allocate a vio_dev for this device */
-	viodev = kmalloc(sizeof(struct vio_dev), GFP_KERNEL);
-	if (!viodev)
-		return NULL;
-	memset(viodev, 0, sizeof(struct vio_dev));
-
-	snprintf(viodev->dev.bus_id, BUS_ID_SIZE, "%s%d", type, unit_num);
-
-	viodev->name = viodev->dev.bus_id;
-	viodev->type = type;
-	viodev->unit_address = unit_num;
-	viodev->iommu_table = &vio_iommu_table;
-	if (vio_register_device(viodev) == NULL) {
-		kfree(viodev);
-		return NULL;
-	}
-	return viodev;
-}
-
-void __init probe_bus_iseries(void)
-{
-	HvLpIndexMap vlan_map;
-	struct vio_dev *viodev;
-	int i;
-
-	/* there is only one of each of these */
-	vio_register_device_iseries("viocons", 0);
-	vio_register_device_iseries("vscsi", 0);
-
-	vlan_map = HvLpConfig_getVirtualLanIndexMap();
-	for (i = 0; i < HVMAXARCHITECTEDVIRTUALLANS; i++) {
-		if ((vlan_map & (0x8000 >> i)) == 0)
-			continue;
-		viodev = vio_register_device_iseries("vlan", i);
-		/* veth is special and has it own iommu_table */
-		viodev->iommu_table = &veth_iommu_table;
-	}
-	for (i = 0; i < HVMAXARCHITECTEDVIRTUALDISKS; i++)
-		vio_register_device_iseries("viodasd", i);
-	for (i = 0; i < HVMAXARCHITECTEDVIRTUALCDROMS; i++)
-		vio_register_device_iseries("viocd", i);
-	for (i = 0; i < HVMAXARCHITECTEDVIRTUALTAPES; i++)
-		vio_register_device_iseries("viotape", i);
-}
-
-/**
- * vio_match_device_iseries: - Tell if a iSeries VIO device matches a
- *	vio_device_id
- */
-static int vio_match_device_iseries(const struct vio_device_id *id,
-		const struct vio_dev *dev)
-{
-	return strncmp(dev->type, id->type, strlen(id->type)) == 0;
-}
-
-static struct vio_bus_ops vio_bus_ops_iseries = {
-	.match = vio_match_device_iseries,
-};
-
-/**
- * vio_bus_init_iseries: - Initialize the iSeries virtual IO bus
- */
-static int __init vio_bus_init_iseries(void)
-{
-	int err;
-
-	err = vio_bus_init(&vio_bus_ops_iseries);
-	if (err == 0) {
-		iommu_vio_init();
-		vio_bus_device.iommu_table = &vio_iommu_table;
-		iSeries_vio_dev = &vio_bus_device.dev;
-		probe_bus_iseries();
-	}
-	return err;
-}
-
-__initcall(vio_bus_init_iseries);
diff --git a/arch/powerpc/platforms/maple/pci.c b/arch/powerpc/platforms/maple/pci.c
index 85d6c93..9a4efc0 100644
--- a/arch/powerpc/platforms/maple/pci.c
+++ b/arch/powerpc/platforms/maple/pci.c
@@ -437,9 +437,6 @@
 
 	/* Tell pci.c to not change any resource allocations.  */
 	pci_probe_only = 1;
-	
-	/* Allow all IO */
-	io_page_mask = -1;
 }
 
 int maple_pci_get_legacy_ide_irq(struct pci_dev *pdev, int channel)
diff --git a/arch/powerpc/platforms/maple/setup.c b/arch/powerpc/platforms/maple/setup.c
index 24c0aef4..a0505ea 100644
--- a/arch/powerpc/platforms/maple/setup.c
+++ b/arch/powerpc/platforms/maple/setup.c
@@ -189,7 +189,7 @@
 	conswitchp = &dummy_con;
 #endif
 
-	printk(KERN_INFO "Using native/NAP idle loop\n");
+	printk(KERN_DEBUG "Using native/NAP idle loop\n");
 }
 
 /* 
diff --git a/arch/powerpc/platforms/powermac/feature.c b/arch/powerpc/platforms/powermac/feature.c
index a5063cd..85e00cb 100644
--- a/arch/powerpc/platforms/powermac/feature.c
+++ b/arch/powerpc/platforms/powermac/feature.c
@@ -2510,7 +2510,7 @@
 		if (get_property(np, "flush-on-lock", NULL))
 			break;
 		powersave_nap = 1;
-		printk(KERN_INFO "Processor NAP mode on idle enabled.\n");
+		printk(KERN_DEBUG "Processor NAP mode on idle enabled.\n");
 		break;
 	}
 
diff --git a/arch/powerpc/platforms/powermac/pci.c b/arch/powerpc/platforms/powermac/pci.c
index ea179af..8003585 100644
--- a/arch/powerpc/platforms/powermac/pci.c
+++ b/arch/powerpc/platforms/powermac/pci.c
@@ -1068,9 +1068,6 @@
 	/* Tell pci.c to not use the common resource allocation mechanism */
 	pci_probe_only = 1;
 
-	/* Allow all IO */
-	io_page_mask = -1;
-
 #else /* CONFIG_PPC64 */
 	init_p2pbridge();
 	fixup_nec_usb2();
diff --git a/arch/powerpc/platforms/pseries/Makefile b/arch/powerpc/platforms/pseries/Makefile
index 9308986..b46ce3b 100644
--- a/arch/powerpc/platforms/pseries/Makefile
+++ b/arch/powerpc/platforms/pseries/Makefile
@@ -2,7 +2,6 @@
 			   setup.o iommu.o ras.o rtasd.o pci_dlpar.o \
 			   firmware.o
 obj-$(CONFIG_SMP)	+= smp.o
-obj-$(CONFIG_IBMVIO)	+= vio.o
 obj-$(CONFIG_XICS)	+= xics.o
 obj-$(CONFIG_SCANLOG)	+= scanlog.o
 obj-$(CONFIG_EEH)	+= eeh.o eeh_cache.o eeh_driver.o eeh_event.o
diff --git a/arch/powerpc/platforms/pseries/eeh_driver.c b/arch/powerpc/platforms/pseries/eeh_driver.c
index 1fba695..4d45347 100644
--- a/arch/powerpc/platforms/pseries/eeh_driver.c
+++ b/arch/powerpc/platforms/pseries/eeh_driver.c
@@ -23,9 +23,8 @@
  *
  */
 #include <linux/delay.h>
-#include <linux/irq.h>
 #include <linux/interrupt.h>
-#include <linux/notifier.h>
+#include <linux/irq.h>
 #include <linux/pci.h>
 #include <asm/eeh.h>
 #include <asm/eeh_event.h>
@@ -202,7 +201,11 @@
 
 static int eeh_reset_device (struct pci_dn *pe_dn, struct pci_bus *bus)
 {
-	int rc;
+	int cnt, rc;
+
+	/* pcibios will clear the counter; save the value */
+	cnt = pe_dn->eeh_freeze_count;
+
 	if (bus)
 		pcibios_remove_pci_devices(bus);
 
@@ -241,6 +244,7 @@
 		ssleep (5);
 		pcibios_add_pci_devices(bus);
 	}
+	pe_dn->eeh_freeze_count = cnt;
 
 	return 0;
 }
@@ -250,7 +254,7 @@
  */
 #define MAX_WAIT_FOR_RECOVERY 15
 
-void handle_eeh_events (struct eeh_event *event)
+struct pci_dn * handle_eeh_events (struct eeh_event *event)
 {
 	struct device_node *frozen_dn;
 	struct pci_dn *frozen_pdn;
@@ -265,7 +269,7 @@
 	if (!frozen_dn) {
 		printk(KERN_ERR "EEH: Error: Cannot find partition endpoint for %s\n",
 		        pci_name(event->dev));
-		return;
+		return NULL;
 	}
 
 	/* There are two different styles for coming up with the PE.
@@ -280,7 +284,7 @@
 	if (!frozen_bus) {
 		printk(KERN_ERR "EEH: Cannot find PCI bus for %s\n",
 		        frozen_dn->full_name);
-		return;
+		return NULL;
 	}
 
 #if 0
@@ -355,7 +359,7 @@
 	/* Tell all device drivers that they can resume operations */
 	pci_walk_bus(frozen_bus, eeh_report_resume, NULL);
 
-	return;
+	return frozen_pdn;
 	
 excess_failures:
 	/*
@@ -384,6 +388,8 @@
 
 	/* Shut down the device drivers for good. */
 	pcibios_remove_pci_devices(frozen_bus);
+
+	return NULL;
 }
 
 /* ---------- end of file ---------- */
diff --git a/arch/powerpc/platforms/pseries/eeh_event.c b/arch/powerpc/platforms/pseries/eeh_event.c
index 40020c6..8f2d129 100644
--- a/arch/powerpc/platforms/pseries/eeh_event.c
+++ b/arch/powerpc/platforms/pseries/eeh_event.c
@@ -18,6 +18,7 @@
  * Copyright (c) 2005 Linas Vepstas <linas@linas.org>
  */
 
+#include <linux/delay.h>
 #include <linux/list.h>
 #include <linux/mutex.h>
 #include <linux/pci.h>
@@ -56,38 +57,43 @@
 {
 	unsigned long flags;
 	struct eeh_event	*event;
+	struct pci_dn *pdn;
 
 	daemonize ("eehd");
+	set_current_state(TASK_INTERRUPTIBLE);
 
-	while (1) {
-		set_current_state(TASK_INTERRUPTIBLE);
+	spin_lock_irqsave(&eeh_eventlist_lock, flags);
+	event = NULL;
 
-		spin_lock_irqsave(&eeh_eventlist_lock, flags);
-		event = NULL;
+	/* Unqueue the event, get ready to process. */
+	if (!list_empty(&eeh_eventlist)) {
+		event = list_entry(eeh_eventlist.next, struct eeh_event, list);
+		list_del(&event->list);
+	}
+	spin_unlock_irqrestore(&eeh_eventlist_lock, flags);
 
-		/* Unqueue the event, get ready to process. */
-		if (!list_empty(&eeh_eventlist)) {
-			event = list_entry(eeh_eventlist.next, struct eeh_event, list);
-			list_del(&event->list);
-		}
-		spin_unlock_irqrestore(&eeh_eventlist_lock, flags);
+	if (event == NULL)
+		return 0;
 
-		if (event == NULL)
-			break;
+	/* Serialize processing of EEH events */
+	mutex_lock(&eeh_event_mutex);
+	eeh_mark_slot(event->dn, EEH_MODE_RECOVERING);
 
-		/* Serialize processing of EEH events */
-		mutex_lock(&eeh_event_mutex);
-		eeh_mark_slot(event->dn, EEH_MODE_RECOVERING);
+	printk(KERN_INFO "EEH: Detected PCI bus error on device %s\n",
+	       pci_name(event->dev));
 
-		printk(KERN_INFO "EEH: Detected PCI bus error on device %s\n",
-		       pci_name(event->dev));
+	pdn = handle_eeh_events(event);
 
-		handle_eeh_events(event);
+	eeh_clear_slot(event->dn, EEH_MODE_RECOVERING);
+	pci_dev_put(event->dev);
+	kfree(event);
+	mutex_unlock(&eeh_event_mutex);
 
-		eeh_clear_slot(event->dn, EEH_MODE_RECOVERING);
-		pci_dev_put(event->dev);
-		kfree(event);
-		mutex_unlock(&eeh_event_mutex);
+	/* If there are no new errors after an hour, clear the counter. */
+	if (pdn && pdn->eeh_freeze_count>0) {
+		msleep_interruptible (3600*1000);
+		if (pdn->eeh_freeze_count>0)
+			pdn->eeh_freeze_count--;
 	}
 
 	return 0;
diff --git a/arch/powerpc/platforms/pseries/iommu.c b/arch/powerpc/platforms/pseries/iommu.c
index 2643078..44a507e 100644
--- a/arch/powerpc/platforms/pseries/iommu.c
+++ b/arch/powerpc/platforms/pseries/iommu.c
@@ -1,23 +1,24 @@
 /*
  * Copyright (C) 2001 Mike Corrigan & Dave Engebretsen, IBM Corporation
  *
- * Rewrite, cleanup: 
+ * Rewrite, cleanup:
  *
  * Copyright (C) 2004 Olof Johansson <olof@lixom.net>, IBM Corporation
+ * Copyright (C) 2006 Olof Johansson <olof@lixom.net>
  *
  * Dynamic DMA mapping support, pSeries-specific parts, both SMP and LPAR.
  *
- * 
+ *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
  * the Free Software Foundation; either version 2 of the License, or
  * (at your option) any later version.
- * 
+ *
  * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
- * 
+ *
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307 USA
@@ -49,52 +50,46 @@
 
 #define DBG(fmt...)
 
-static void tce_build_pSeries(struct iommu_table *tbl, long index, 
-			      long npages, unsigned long uaddr, 
+static void tce_build_pSeries(struct iommu_table *tbl, long index,
+			      long npages, unsigned long uaddr,
 			      enum dma_data_direction direction)
 {
-	union tce_entry t;
-	union tce_entry *tp;
+	u64 proto_tce;
+	u64 *tcep;
+	u64 rpn;
 
 	index <<= TCE_PAGE_FACTOR;
 	npages <<= TCE_PAGE_FACTOR;
 
-	t.te_word = 0;
-	t.te_rdwr = 1; // Read allowed 
+	proto_tce = TCE_PCI_READ; // Read allowed
 
 	if (direction != DMA_TO_DEVICE)
-		t.te_pciwr = 1;
+		proto_tce |= TCE_PCI_WRITE;
 
-	tp = ((union tce_entry *)tbl->it_base) + index;
+	tcep = ((u64 *)tbl->it_base) + index;
 
 	while (npages--) {
 		/* can't move this out since we might cross LMB boundary */
-		t.te_rpn = (virt_to_abs(uaddr)) >> TCE_SHIFT;
-	
-		tp->te_word = t.te_word;
+		rpn = (virt_to_abs(uaddr)) >> TCE_SHIFT;
+		*tcep = proto_tce | (rpn & TCE_RPN_MASK) << TCE_RPN_SHIFT;
 
 		uaddr += TCE_PAGE_SIZE;
-		tp++;
+		tcep++;
 	}
 }
 
 
 static void tce_free_pSeries(struct iommu_table *tbl, long index, long npages)
 {
-	union tce_entry t;
-	union tce_entry *tp;
+	u64 *tcep;
 
 	npages <<= TCE_PAGE_FACTOR;
 	index <<= TCE_PAGE_FACTOR;
 
-	t.te_word = 0;
-	tp  = ((union tce_entry *)tbl->it_base) + index;
-		
-	while (npages--) {
-		tp->te_word = t.te_word;
-		
-		tp++;
-	}
+	tcep = ((u64 *)tbl->it_base) + index;
+
+	while (npages--)
+		*(tcep++) = 0;
 }
 
 
@@ -103,43 +98,44 @@
 				enum dma_data_direction direction)
 {
 	u64 rc;
-	union tce_entry tce;
+	u64 proto_tce, tce;
+	u64 rpn;
 
 	tcenum <<= TCE_PAGE_FACTOR;
 	npages <<= TCE_PAGE_FACTOR;
 
-	tce.te_word = 0;
-	tce.te_rpn = (virt_to_abs(uaddr)) >> TCE_SHIFT;
-	tce.te_rdwr = 1;
+	rpn = (virt_to_abs(uaddr)) >> TCE_SHIFT;
+	proto_tce = TCE_PCI_READ;
 	if (direction != DMA_TO_DEVICE)
-		tce.te_pciwr = 1;
+		proto_tce |= TCE_PCI_WRITE;
 
 	while (npages--) {
-		rc = plpar_tce_put((u64)tbl->it_index, 
-				   (u64)tcenum << 12, 
-				   tce.te_word );
-		
+		tce = proto_tce | (rpn & TCE_RPN_MASK) << TCE_RPN_SHIFT;
+		rc = plpar_tce_put((u64)tbl->it_index, (u64)tcenum << 12, tce);
+
 		if (rc && printk_ratelimit()) {
 			printk("tce_build_pSeriesLP: plpar_tce_put failed. rc=%ld\n", rc);
 			printk("\tindex   = 0x%lx\n", (u64)tbl->it_index);
 			printk("\ttcenum  = 0x%lx\n", (u64)tcenum);
-			printk("\ttce val = 0x%lx\n", tce.te_word );
+			printk("\ttce val = 0x%lx\n", tce );
 			show_stack(current, (unsigned long *)__get_SP());
 		}
-			
+
 		tcenum++;
-		tce.te_rpn++;
+		rpn++;
 	}
 }
 
-static DEFINE_PER_CPU(void *, tce_page) = NULL;
+static DEFINE_PER_CPU(u64 *, tce_page) = NULL;
 
 static void tce_buildmulti_pSeriesLP(struct iommu_table *tbl, long tcenum,
 				     long npages, unsigned long uaddr,
 				     enum dma_data_direction direction)
 {
 	u64 rc;
-	union tce_entry tce, *tcep;
+	u64 proto_tce;
+	u64 *tcep;
+	u64 rpn;
 	long l, limit;
 
 	if (TCE_PAGE_FACTOR == 0 && npages == 1)
@@ -152,7 +148,7 @@
 	 * from iommu_alloc{,_sg}()
 	 */
 	if (!tcep) {
-		tcep = (void *)__get_free_page(GFP_ATOMIC);
+		tcep = (u64 *)__get_free_page(GFP_ATOMIC);
 		/* If allocation fails, fall back to the loop implementation */
 		if (!tcep)
 			return tce_build_pSeriesLP(tbl, tcenum, npages,
@@ -163,11 +159,10 @@
 	tcenum <<= TCE_PAGE_FACTOR;
 	npages <<= TCE_PAGE_FACTOR;
 
-	tce.te_word = 0;
-	tce.te_rpn = (virt_to_abs(uaddr)) >> TCE_SHIFT;
-	tce.te_rdwr = 1;
+	rpn = (virt_to_abs(uaddr)) >> TCE_SHIFT;
+	proto_tce = TCE_PCI_READ;
 	if (direction != DMA_TO_DEVICE)
-		tce.te_pciwr = 1;
+		proto_tce |= TCE_PCI_WRITE;
 
 	/* We can map max one pageful of TCEs at a time */
 	do {
@@ -175,11 +170,11 @@
 		 * Set up the page with TCE data, looping through and setting
 		 * the values.
 		 */
-		limit = min_t(long, npages, 4096/sizeof(union tce_entry));
+		limit = min_t(long, npages, 4096/TCE_ENTRY_SIZE);
 
 		for (l = 0; l < limit; l++) {
-			tcep[l] = tce;
-			tce.te_rpn++;
+			tcep[l] = proto_tce | (rpn & TCE_RPN_MASK) << TCE_RPN_SHIFT;
+			rpn++;
 		}
 
 		rc = plpar_tce_put_indirect((u64)tbl->it_index,
@@ -195,7 +190,7 @@
 		printk("tce_buildmulti_pSeriesLP: plpar_tce_put failed. rc=%ld\n", rc);
 		printk("\tindex   = 0x%lx\n", (u64)tbl->it_index);
 		printk("\tnpages  = 0x%lx\n", (u64)npages);
-		printk("\ttce[0] val = 0x%lx\n", tcep[0].te_word);
+		printk("\ttce[0] val = 0x%lx\n", tcep[0]);
 		show_stack(current, (unsigned long *)__get_SP());
 	}
 }
@@ -203,23 +198,17 @@
 static void tce_free_pSeriesLP(struct iommu_table *tbl, long tcenum, long npages)
 {
 	u64 rc;
-	union tce_entry tce;
 
 	tcenum <<= TCE_PAGE_FACTOR;
 	npages <<= TCE_PAGE_FACTOR;
 
-	tce.te_word = 0;
-
 	while (npages--) {
-		rc = plpar_tce_put((u64)tbl->it_index,
-				   (u64)tcenum << 12,
-				   tce.te_word);
+		rc = plpar_tce_put((u64)tbl->it_index, (u64)tcenum << 12, 0);
 
 		if (rc && printk_ratelimit()) {
 			printk("tce_free_pSeriesLP: plpar_tce_put failed. rc=%ld\n", rc);
 			printk("\tindex   = 0x%lx\n", (u64)tbl->it_index);
 			printk("\ttcenum  = 0x%lx\n", (u64)tcenum);
-			printk("\ttce val = 0x%lx\n", tce.te_word );
 			show_stack(current, (unsigned long *)__get_SP());
 		}
 
@@ -231,31 +220,24 @@
 static void tce_freemulti_pSeriesLP(struct iommu_table *tbl, long tcenum, long npages)
 {
 	u64 rc;
-	union tce_entry tce;
 
 	tcenum <<= TCE_PAGE_FACTOR;
 	npages <<= TCE_PAGE_FACTOR;
 
-	tce.te_word = 0;
-
-	rc = plpar_tce_stuff((u64)tbl->it_index,
-			   (u64)tcenum << 12,
-			   tce.te_word,
-			   npages);
+	rc = plpar_tce_stuff((u64)tbl->it_index, (u64)tcenum << 12, 0, npages);
 
 	if (rc && printk_ratelimit()) {
 		printk("tce_freemulti_pSeriesLP: plpar_tce_stuff failed\n");
 		printk("\trc      = %ld\n", rc);
 		printk("\tindex   = 0x%lx\n", (u64)tbl->it_index);
 		printk("\tnpages  = 0x%lx\n", (u64)npages);
-		printk("\ttce val = 0x%lx\n", tce.te_word );
 		show_stack(current, (unsigned long *)__get_SP());
 	}
 }
 
 static void iommu_table_setparms(struct pci_controller *phb,
 				 struct device_node *dn,
-				 struct iommu_table *tbl) 
+				 struct iommu_table *tbl)
 {
 	struct device_node *node;
 	unsigned long *basep;
@@ -275,16 +257,16 @@
 	memset((void *)tbl->it_base, 0, *sizep);
 
 	tbl->it_busno = phb->bus->number;
-	
+
 	/* Units of tce entries */
 	tbl->it_offset = phb->dma_window_base_cur >> PAGE_SHIFT;
-	
+
 	/* Test if we are going over 2GB of DMA space */
 	if (phb->dma_window_base_cur + phb->dma_window_size > 0x80000000ul) {
 		udbg_printf("PCI_DMA: Unexpected number of IOAs under this PHB.\n");
-		panic("PCI_DMA: Unexpected number of IOAs under this PHB.\n"); 
+		panic("PCI_DMA: Unexpected number of IOAs under this PHB.\n");
 	}
-	
+
 	phb->dma_window_base_cur += phb->dma_window_size;
 
 	/* Set the tce table size - measured in entries */
@@ -299,30 +281,22 @@
  * iommu_table_setparms_lpar
  *
  * Function: On pSeries LPAR systems, return TCE table info, given a pci bus.
- *
- * ToDo: properly interpret the ibm,dma-window property.  The definition is:
- *	logical-bus-number	(1 word)
- *	phys-address		(#address-cells words)
- *	size			(#cell-size words)
- *
- * Currently we hard code these sizes (more or less).
  */
 static void iommu_table_setparms_lpar(struct pci_controller *phb,
 				      struct device_node *dn,
 				      struct iommu_table *tbl,
-				      unsigned int *dma_window)
+				      unsigned char *dma_window)
 {
-	tbl->it_busno  = PCI_DN(dn)->bussubno;
+	unsigned long offset, size;
 
-	/* TODO: Parse field size properties properly. */
-	tbl->it_size   = (((unsigned long)dma_window[4] << 32) |
-			   (unsigned long)dma_window[5]) >> PAGE_SHIFT;
-	tbl->it_offset = (((unsigned long)dma_window[2] << 32) |
-			   (unsigned long)dma_window[3]) >> PAGE_SHIFT;
+	tbl->it_busno  = PCI_DN(dn)->bussubno;
+	of_parse_dma_window(dn, dma_window, &tbl->it_index, &offset, &size);
+
 	tbl->it_base   = 0;
-	tbl->it_index  = dma_window[0];
 	tbl->it_blocksize  = 16;
 	tbl->it_type = TCE_PCI;
+	tbl->it_offset = offset >> PAGE_SHIFT;
+	tbl->it_size = size >> PAGE_SHIFT;
 }
 
 static void iommu_bus_setup_pSeries(struct pci_bus *bus)
@@ -414,7 +388,7 @@
 	struct iommu_table *tbl;
 	struct device_node *dn, *pdn;
 	struct pci_dn *ppci;
-	unsigned int *dma_window = NULL;
+	unsigned char *dma_window = NULL;
 
 	DBG("iommu_bus_setup_pSeriesLP, bus %p, bus->self %p\n", bus, bus->self);
 
@@ -422,7 +396,7 @@
 
 	/* Find nearest ibm,dma-window, walking up the device tree */
 	for (pdn = dn; pdn != NULL; pdn = pdn->parent) {
-		dma_window = (unsigned int *)get_property(pdn, "ibm,dma-window", NULL);
+		dma_window = get_property(pdn, "ibm,dma-window", NULL);
 		if (dma_window != NULL)
 			break;
 	}
@@ -442,7 +416,7 @@
 
 		tbl = (struct iommu_table *)kmalloc(sizeof(struct iommu_table),
 						    GFP_KERNEL);
-	
+
 		iommu_table_setparms_lpar(ppci->phb, pdn, tbl, dma_window);
 
 		ppci->iommu_table = iommu_init_table(tbl);
@@ -516,7 +490,7 @@
 {
 	struct device_node *pdn, *dn;
 	struct iommu_table *tbl;
-	int *dma_window = NULL;
+	unsigned char *dma_window = NULL;
 	struct pci_dn *pci;
 
 	DBG("iommu_dev_setup_pSeriesLP, dev %p (%s)\n", dev, pci_name(dev));
@@ -531,8 +505,7 @@
 
 	for (pdn = dn; pdn && PCI_DN(pdn) && !PCI_DN(pdn)->iommu_table;
 	     pdn = pdn->parent) {
-		dma_window = (unsigned int *)
-			get_property(pdn, "ibm,dma-window", NULL);
+		dma_window = get_property(pdn, "ibm,dma-window", NULL);
 		if (dma_window)
 			break;
 	}
diff --git a/arch/powerpc/platforms/pseries/rtasd.c b/arch/powerpc/platforms/pseries/rtasd.c
index e0000ce..2e4e040 100644
--- a/arch/powerpc/platforms/pseries/rtasd.c
+++ b/arch/powerpc/platforms/pseries/rtasd.c
@@ -348,7 +348,7 @@
 		return 0;
 
 	if (error == -EINVAL) {
-		printk(KERN_INFO "rtasd: surveillance not supported\n");
+		printk(KERN_DEBUG "rtasd: surveillance not supported\n");
 		return 0;
 	}
 
@@ -440,7 +440,7 @@
 		goto error;
 	}
 
-	printk(KERN_INFO "RTAS daemon started\n");
+	printk(KERN_DEBUG "RTAS daemon started\n");
 
 	DEBUG("will sleep for %d milliseconds\n", (30000/rtas_event_scan_rate));
 
@@ -487,7 +487,7 @@
 
 	/* No RTAS */
 	if (rtas_token("event-scan") == RTAS_UNKNOWN_SERVICE) {
-		printk(KERN_INFO "rtasd: no event-scan on system\n");
+		printk(KERN_DEBUG "rtasd: no event-scan on system\n");
 		return -ENODEV;
 	}
 
diff --git a/arch/powerpc/platforms/pseries/setup.c b/arch/powerpc/platforms/pseries/setup.c
index 5f79f01..ee89d19 100644
--- a/arch/powerpc/platforms/pseries/setup.c
+++ b/arch/powerpc/platforms/pseries/setup.c
@@ -235,14 +235,14 @@
 	if (firmware_has_feature(FW_FEATURE_SPLPAR)) {
 		vpa_init(boot_cpuid);
 		if (get_lppaca()->shared_proc) {
-			printk(KERN_INFO "Using shared processor idle loop\n");
+			printk(KERN_DEBUG "Using shared processor idle loop\n");
 			ppc_md.power_save = pseries_shared_idle_sleep;
 		} else {
-			printk(KERN_INFO "Using dedicated idle loop\n");
+			printk(KERN_DEBUG "Using dedicated idle loop\n");
 			ppc_md.power_save = pseries_dedicated_idle_sleep;
 		}
 	} else {
-		printk(KERN_INFO "Using default idle loop\n");
+		printk(KERN_DEBUG "Using default idle loop\n");
 	}
 
 	if (firmware_has_feature(FW_FEATURE_LPAR))
diff --git a/arch/powerpc/platforms/pseries/vio.c b/arch/powerpc/platforms/pseries/vio.c
deleted file mode 100644
index 8e53e04..0000000
--- a/arch/powerpc/platforms/pseries/vio.c
+++ /dev/null
@@ -1,274 +0,0 @@
-/*
- * IBM PowerPC pSeries Virtual I/O Infrastructure Support.
- *
- *    Copyright (c) 2003-2005 IBM Corp.
- *     Dave Engebretsen engebret@us.ibm.com
- *     Santiago Leon santil@us.ibm.com
- *     Hollis Blanchard <hollisb@us.ibm.com>
- *     Stephen Rothwell
- *
- *      This program is free software; you can redistribute it and/or
- *      modify it under the terms of the GNU General Public License
- *      as published by the Free Software Foundation; either version
- *      2 of the License, or (at your option) any later version.
- */
-
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/mm.h>
-#include <linux/kobject.h>
-#include <asm/iommu.h>
-#include <asm/dma.h>
-#include <asm/prom.h>
-#include <asm/vio.h>
-#include <asm/hvcall.h>
-#include <asm/tce.h>
-
-extern struct subsystem devices_subsys; /* needed for vio_find_name() */
-
-static void probe_bus_pseries(void)
-{
-	struct device_node *node_vroot, *of_node;
-
-	node_vroot = find_devices("vdevice");
-	if ((node_vroot == NULL) || (node_vroot->child == NULL))
-		/* this machine doesn't do virtual IO, and that's ok */
-		return;
-
-	/*
-	 * Create struct vio_devices for each virtual device in the device tree.
-	 * Drivers will associate with them later.
-	 */
-	for (of_node = node_vroot->child; of_node != NULL;
-			of_node = of_node->sibling) {
-		printk(KERN_DEBUG "%s: processing %p\n", __FUNCTION__, of_node);
-		vio_register_device_node(of_node);
-	}
-}
-
-/**
- * vio_match_device_pseries: - Tell if a pSeries VIO device matches a
- *	vio_device_id
- */
-static int vio_match_device_pseries(const struct vio_device_id *id,
-		const struct vio_dev *dev)
-{
-	return (strncmp(dev->type, id->type, strlen(id->type)) == 0) &&
-			device_is_compatible(dev->dev.platform_data, id->compat);
-}
-
-static void vio_release_device_pseries(struct device *dev)
-{
-	/* XXX free TCE table */
-	of_node_put(dev->platform_data);
-}
-
-static ssize_t viodev_show_devspec(struct device *dev,
-		struct device_attribute *attr, char *buf)
-{
-	struct device_node *of_node = dev->platform_data;
-
-	return sprintf(buf, "%s\n", of_node->full_name);
-}
-DEVICE_ATTR(devspec, S_IRUSR | S_IRGRP | S_IROTH, viodev_show_devspec, NULL);
-
-static void vio_unregister_device_pseries(struct vio_dev *viodev)
-{
-	device_remove_file(&viodev->dev, &dev_attr_devspec);
-}
-
-static struct vio_bus_ops vio_bus_ops_pseries = {
-	.match = vio_match_device_pseries,
-	.unregister_device = vio_unregister_device_pseries,
-	.release_device = vio_release_device_pseries,
-};
-
-/**
- * vio_bus_init_pseries: - Initialize the pSeries virtual IO bus
- */
-static int __init vio_bus_init_pseries(void)
-{
-	int err;
-
-	err = vio_bus_init(&vio_bus_ops_pseries);
-	if (err == 0)
-		probe_bus_pseries();
-	return err;
-}
-
-__initcall(vio_bus_init_pseries);
-
-/**
- * vio_build_iommu_table: - gets the dma information from OF and
- *	builds the TCE tree.
- * @dev: the virtual device.
- *
- * Returns a pointer to the built tce tree, or NULL if it can't
- * find property.
-*/
-static struct iommu_table *vio_build_iommu_table(struct vio_dev *dev)
-{
-	unsigned int *dma_window;
-	struct iommu_table *newTceTable;
-	unsigned long offset;
-	int dma_window_property_size;
-
-	dma_window = (unsigned int *) get_property(dev->dev.platform_data, "ibm,my-dma-window", &dma_window_property_size);
-	if(!dma_window) {
-		return NULL;
-	}
-
-	newTceTable = (struct iommu_table *) kmalloc(sizeof(struct iommu_table), GFP_KERNEL);
-
-	/*  There should be some code to extract the phys-encoded offset
-		using prom_n_addr_cells(). However, according to a comment
-		on earlier versions, it's always zero, so we don't bother */
-	offset = dma_window[1] >>  PAGE_SHIFT;
-
-	/* TCE table size - measured in tce entries */
-	newTceTable->it_size		= dma_window[4] >> PAGE_SHIFT;
-	/* offset for VIO should always be 0 */
-	newTceTable->it_offset		= offset;
-	newTceTable->it_busno		= 0;
-	newTceTable->it_index		= (unsigned long)dma_window[0];
-	newTceTable->it_type		= TCE_VB;
-
-	return iommu_init_table(newTceTable);
-}
-
-/**
- * vio_register_device_node: - Register a new vio device.
- * @of_node:	The OF node for this device.
- *
- * Creates and initializes a vio_dev structure from the data in
- * of_node (dev.platform_data) and adds it to the list of virtual devices.
- * Returns a pointer to the created vio_dev or NULL if node has
- * NULL device_type or compatible fields.
- */
-struct vio_dev * __devinit vio_register_device_node(struct device_node *of_node)
-{
-	struct vio_dev *viodev;
-	unsigned int *unit_address;
-	unsigned int *irq_p;
-
-	/* we need the 'device_type' property, in order to match with drivers */
-	if ((NULL == of_node->type)) {
-		printk(KERN_WARNING
-			"%s: node %s missing 'device_type'\n", __FUNCTION__,
-			of_node->name ? of_node->name : "<unknown>");
-		return NULL;
-	}
-
-	unit_address = (unsigned int *)get_property(of_node, "reg", NULL);
-	if (!unit_address) {
-		printk(KERN_WARNING "%s: node %s missing 'reg'\n", __FUNCTION__,
-			of_node->name ? of_node->name : "<unknown>");
-		return NULL;
-	}
-
-	/* allocate a vio_dev for this node */
-	viodev = kmalloc(sizeof(struct vio_dev), GFP_KERNEL);
-	if (!viodev) {
-		return NULL;
-	}
-	memset(viodev, 0, sizeof(struct vio_dev));
-
-	viodev->dev.platform_data = of_node_get(of_node);
-
-	viodev->irq = NO_IRQ;
-	irq_p = (unsigned int *)get_property(of_node, "interrupts", NULL);
-	if (irq_p) {
-		int virq = virt_irq_create_mapping(*irq_p);
-		if (virq == NO_IRQ) {
-			printk(KERN_ERR "Unable to allocate interrupt "
-			       "number for %s\n", of_node->full_name);
-		} else
-			viodev->irq = irq_offset_up(virq);
-	}
-
-	snprintf(viodev->dev.bus_id, BUS_ID_SIZE, "%x", *unit_address);
-	viodev->name = of_node->name;
-	viodev->type = of_node->type;
-	viodev->unit_address = *unit_address;
-	viodev->iommu_table = vio_build_iommu_table(viodev);
-
-	/* register with generic device framework */
-	if (vio_register_device(viodev) == NULL) {
-		/* XXX free TCE table */
-		kfree(viodev);
-		return NULL;
-	}
-	device_create_file(&viodev->dev, &dev_attr_devspec);
-
-	return viodev;
-}
-EXPORT_SYMBOL(vio_register_device_node);
-
-/**
- * vio_get_attribute: - get attribute for virtual device
- * @vdev:	The vio device to get property.
- * @which:	The property/attribute to be extracted.
- * @length:	Pointer to length of returned data size (unused if NULL).
- *
- * Calls prom.c's get_property() to return the value of the
- * attribute specified by the preprocessor constant @which
-*/
-const void * vio_get_attribute(struct vio_dev *vdev, void* which, int* length)
-{
-	return get_property(vdev->dev.platform_data, (char*)which, length);
-}
-EXPORT_SYMBOL(vio_get_attribute);
-
-/* vio_find_name() - internal because only vio.c knows how we formatted the
- * kobject name
- * XXX once vio_bus_type.devices is actually used as a kset in
- * drivers/base/bus.c, this function should be removed in favor of
- * "device_find(kobj_name, &vio_bus_type)"
- */
-static struct vio_dev *vio_find_name(const char *kobj_name)
-{
-	struct kobject *found;
-
-	found = kset_find_obj(&devices_subsys.kset, kobj_name);
-	if (!found)
-		return NULL;
-
-	return to_vio_dev(container_of(found, struct device, kobj));
-}
-
-/**
- * vio_find_node - find an already-registered vio_dev
- * @vnode: device_node of the virtual device we're looking for
- */
-struct vio_dev *vio_find_node(struct device_node *vnode)
-{
-	uint32_t *unit_address;
-	char kobj_name[BUS_ID_SIZE];
-
-	/* construct the kobject name from the device node */
-	unit_address = (uint32_t *)get_property(vnode, "reg", NULL);
-	if (!unit_address)
-		return NULL;
-	snprintf(kobj_name, BUS_ID_SIZE, "%x", *unit_address);
-
-	return vio_find_name(kobj_name);
-}
-EXPORT_SYMBOL(vio_find_node);
-
-int vio_enable_interrupts(struct vio_dev *dev)
-{
-	int rc = h_vio_signal(dev->unit_address, VIO_IRQ_ENABLE);
-	if (rc != H_SUCCESS)
-		printk(KERN_ERR "vio: Error 0x%x enabling interrupts\n", rc);
-	return rc;
-}
-EXPORT_SYMBOL(vio_enable_interrupts);
-
-int vio_disable_interrupts(struct vio_dev *dev)
-{
-	int rc = h_vio_signal(dev->unit_address, VIO_IRQ_DISABLE);
-	if (rc != H_SUCCESS)
-		printk(KERN_ERR "vio: Error 0x%x disabling interrupts\n", rc);
-	return rc;
-}
-EXPORT_SYMBOL(vio_disable_interrupts);
diff --git a/arch/powerpc/platforms/pseries/xics.c b/arch/powerpc/platforms/pseries/xics.c
index 2d60ea3..b14f9b5 100644
--- a/arch/powerpc/platforms/pseries/xics.c
+++ b/arch/powerpc/platforms/pseries/xics.c
@@ -522,7 +522,7 @@
 
 	np = of_find_node_by_type(NULL, "interrupt-controller");
 	if (!np) {
-		printk(KERN_WARNING "xics: no ISA interrupt controller\n");
+		printk(KERN_DEBUG "xics: no ISA interrupt controller\n");
 		xics_irq_8259_cascade_real = -1;
 		xics_irq_8259_cascade = -1;
 	} else {
@@ -641,23 +641,26 @@
 	ops->cppr_info(cpu, 0x00);
 	iosync();
 
+	/* Clear IPI */
+	ops->qirr_info(cpu, 0xff);
+
+	/*
+	 * we need to EOI the IPI if we got here from kexec down IPI
+	 *
+	 * probably need to check all the other interrupts too
+	 * should we be flagging idle loop instead?
+	 * or creating some task to be scheduled?
+	 */
+	ops->xirr_info_set(cpu, XICS_IPI);
+
 	/*
 	 * Some machines need to have at least one cpu in the GIQ,
 	 * so leave the master cpu in the group.
 	 */
-	if (secondary) {
-		/*
-		 * we need to EOI the IPI if we got here from kexec down IPI
-		 *
-		 * probably need to check all the other interrupts too
-		 * should we be flagging idle loop instead?
-		 * or creating some task to be scheduled?
-		 */
-		ops->xirr_info_set(cpu, XICS_IPI);
+	if (secondary)
 		rtas_set_indicator(GLOBAL_INTERRUPT_QUEUE,
 			(1UL << interrupt_server_size) - 1 -
 			default_distrib_server, 0);
-	}
 }
 
 #ifdef CONFIG_HOTPLUG_CPU
diff --git a/drivers/block/viodasd.c b/drivers/block/viodasd.c
index f63e07b..b0df4f5 100644
--- a/drivers/block/viodasd.c
+++ b/drivers/block/viodasd.c
@@ -747,7 +747,7 @@
  * support.
  */
 static struct vio_device_id viodasd_device_table[] __devinitdata = {
-	{ "viodasd", "" },
+	{ "block", "IBM,iSeries-viodasd" },
 	{ "", "" }
 };
 MODULE_DEVICE_TABLE(vio, viodasd_device_table);
diff --git a/drivers/cdrom/viocd.c b/drivers/cdrom/viocd.c
index c0f817b..af6b3bf 100644
--- a/drivers/cdrom/viocd.c
+++ b/drivers/cdrom/viocd.c
@@ -731,7 +731,7 @@
  * support.
  */
 static struct vio_device_id viocd_device_table[] __devinitdata = {
-	{ "viocd", "" },
+	{ "block", "IBM,iSeries-viocd" },
 	{ "", "" }
 };
 MODULE_DEVICE_TABLE(vio, viocd_device_table);
diff --git a/drivers/char/hvsi.c b/drivers/char/hvsi.c
index a952218..a0370ed 100644
--- a/drivers/char/hvsi.c
+++ b/drivers/char/hvsi.c
@@ -1179,7 +1179,7 @@
 	if (tty_register_driver(hvsi_driver))
 		panic("Couldn't register hvsi console driver\n");
 
-	printk(KERN_INFO "HVSI: registered %i devices\n", hvsi_count);
+	printk(KERN_DEBUG "HVSI: registered %i devices\n", hvsi_count);
 
 	return 0;
 }
diff --git a/drivers/char/viotape.c b/drivers/char/viotape.c
index 60aabdb..11c7e9d 100644
--- a/drivers/char/viotape.c
+++ b/drivers/char/viotape.c
@@ -989,7 +989,7 @@
  * support.
  */
 static struct vio_device_id viotape_device_table[] __devinitdata = {
-	{ "viotape", "" },
+	{ "byte", "IBM,iSeries-viotape" },
 	{ "", "" }
 };
 MODULE_DEVICE_TABLE(vio, viotape_device_table);
diff --git a/drivers/net/ibmveth.c b/drivers/net/ibmveth.c
index 52d0102..37965dc 100644
--- a/drivers/net/ibmveth.c
+++ b/drivers/net/ibmveth.c
@@ -61,7 +61,7 @@
 #undef DEBUG
 
 #define ibmveth_printk(fmt, args...) \
-  printk(KERN_INFO "%s: " fmt, __FILE__, ## args)
+  printk(KERN_DEBUG "%s: " fmt, __FILE__, ## args)
 
 #define ibmveth_error_printk(fmt, args...) \
   printk(KERN_ERR "(%s:%3.3d ua:%x) ERROR: " fmt, __FILE__, __LINE__ , adapter->vdev->unit_address, ## args)
diff --git a/drivers/net/iseries_veth.c b/drivers/net/iseries_veth.c
index f0f04be..93394d7 100644
--- a/drivers/net/iseries_veth.c
+++ b/drivers/net/iseries_veth.c
@@ -69,6 +69,7 @@
 #include <linux/delay.h>
 #include <linux/mm.h>
 #include <linux/ethtool.h>
+#include <linux/if_ether.h>
 
 #include <asm/abs_addr.h>
 #include <asm/iseries/mf.h>
@@ -1035,11 +1036,22 @@
 	.get_link = veth_get_link,
 };
 
-static struct net_device * __init veth_probe_one(int vlan, struct device *vdev)
+static struct net_device * __init veth_probe_one(int vlan,
+		struct vio_dev *vio_dev)
 {
 	struct net_device *dev;
 	struct veth_port *port;
+	struct device *vdev = &vio_dev->dev;
 	int i, rc;
+	const unsigned char *mac_addr;
+
+	mac_addr = vio_get_attribute(vio_dev, "local-mac-address", NULL);
+	if (mac_addr == NULL)
+		mac_addr = vio_get_attribute(vio_dev, "mac-address", NULL);
+	if (mac_addr == NULL) {
+		veth_error("Unable to fetch MAC address from device tree.\n");
+		return NULL;
+	}
 
 	dev = alloc_etherdev(sizeof (struct veth_port));
 	if (! dev) {
@@ -1064,16 +1076,11 @@
 	}
 	port->dev = vdev;
 
-	dev->dev_addr[0] = 0x02;
-	dev->dev_addr[1] = 0x01;
-	dev->dev_addr[2] = 0xff;
-	dev->dev_addr[3] = vlan;
-	dev->dev_addr[4] = 0xff;
-	dev->dev_addr[5] = this_lp;
+	memcpy(dev->dev_addr, mac_addr, ETH_ALEN);
 
 	dev->mtu = VETH_MAX_MTU;
 
-	memcpy(&port->mac_addr, dev->dev_addr, 6);
+	memcpy(&port->mac_addr, mac_addr, ETH_ALEN);
 
 	dev->open = veth_open;
 	dev->hard_start_xmit = veth_start_xmit;
@@ -1608,7 +1615,7 @@
 	struct net_device *dev;
 	struct veth_port *port;
 
-	dev = veth_probe_one(i, &vdev->dev);
+	dev = veth_probe_one(i, vdev);
 	if (dev == NULL) {
 		veth_remove(vdev);
 		return 1;
@@ -1641,7 +1648,7 @@
  * support.
  */
 static struct vio_device_id veth_device_table[] __devinitdata = {
-	{ "vlan", "" },
+	{ "network", "IBM,iSeries-l-lan" },
 	{ "", "" }
 };
 MODULE_DEVICE_TABLE(vio, veth_device_table);
diff --git a/include/asm-powerpc/eeh.h b/include/asm-powerpc/eeh.h
index 868c713..2c3dc4a 100644
--- a/include/asm-powerpc/eeh.h
+++ b/include/asm-powerpc/eeh.h
@@ -293,8 +293,6 @@
 static inline u8 eeh_inb(unsigned long port)
 {
 	u8 val;
-	if (!_IO_IS_VALID(port))
-		return ~0;
 	val = in_8((u8 __iomem *)(port+pci_io_base));
 	if (EEH_POSSIBLE_ERROR(val, u8))
 		return eeh_check_failure((void __iomem *)(port), val);
@@ -303,15 +301,12 @@
 
 static inline void eeh_outb(u8 val, unsigned long port)
 {
-	if (_IO_IS_VALID(port))
-		out_8((u8 __iomem *)(port+pci_io_base), val);
+	out_8((u8 __iomem *)(port+pci_io_base), val);
 }
 
 static inline u16 eeh_inw(unsigned long port)
 {
 	u16 val;
-	if (!_IO_IS_VALID(port))
-		return ~0;
 	val = in_le16((u16 __iomem *)(port+pci_io_base));
 	if (EEH_POSSIBLE_ERROR(val, u16))
 		return eeh_check_failure((void __iomem *)(port), val);
@@ -320,15 +315,12 @@
 
 static inline void eeh_outw(u16 val, unsigned long port)
 {
-	if (_IO_IS_VALID(port))
-		out_le16((u16 __iomem *)(port+pci_io_base), val);
+	out_le16((u16 __iomem *)(port+pci_io_base), val);
 }
 
 static inline u32 eeh_inl(unsigned long port)
 {
 	u32 val;
-	if (!_IO_IS_VALID(port))
-		return ~0;
 	val = in_le32((u32 __iomem *)(port+pci_io_base));
 	if (EEH_POSSIBLE_ERROR(val, u32))
 		return eeh_check_failure((void __iomem *)(port), val);
@@ -337,8 +329,7 @@
 
 static inline void eeh_outl(u32 val, unsigned long port)
 {
-	if (_IO_IS_VALID(port))
-		out_le32((u32 __iomem *)(port+pci_io_base), val);
+	out_le32((u32 __iomem *)(port+pci_io_base), val);
 }
 
 /* in-string eeh macros */
diff --git a/include/asm-powerpc/eeh_event.h b/include/asm-powerpc/eeh_event.h
index 93d55a2..dc6bf0f 100644
--- a/include/asm-powerpc/eeh_event.h
+++ b/include/asm-powerpc/eeh_event.h
@@ -18,8 +18,8 @@
  * Copyright (c) 2005 Linas Vepstas <linas@linas.org>
  */
 
-#ifndef ASM_PPC64_EEH_EVENT_H
-#define ASM_PPC64_EEH_EVENT_H
+#ifndef ASM_POWERPC_EEH_EVENT_H
+#define ASM_POWERPC_EEH_EVENT_H
 #ifdef __KERNEL__
 
 /** EEH event -- structure holding pci controller data that describes
@@ -39,7 +39,7 @@
  * @dev pci device
  *
  * This routine builds a PCI error event which will be delivered
- * to all listeners on the peh_notifier_chain.
+ * to all listeners on the eeh_notifier_chain.
  *
  * This routine can be called within an interrupt context;
  * the actual event will be delivered in a normal context
@@ -51,7 +51,7 @@
                             int time_unavail);
 
 /* Main recovery function */
-void handle_eeh_events (struct eeh_event *);
+struct pci_dn * handle_eeh_events (struct eeh_event *);
 
 #endif /* __KERNEL__ */
-#endif /* ASM_PPC64_EEH_EVENT_H */
+#endif /* ASM_POWERPC_EEH_EVENT_H */
diff --git a/include/asm-powerpc/io.h b/include/asm-powerpc/io.h
index f1c2469..a9496f3 100644
--- a/include/asm-powerpc/io.h
+++ b/include/asm-powerpc/io.h
@@ -40,12 +40,6 @@
 
 extern unsigned long isa_io_base;
 extern unsigned long pci_io_base;
-extern unsigned long io_page_mask;
-
-#define MAX_ISA_PORT 0x10000
-
-#define _IO_IS_VALID(port) ((port) >= MAX_ISA_PORT || (1 << (port>>PAGE_SHIFT)) \
-			    & io_page_mask)
 
 #ifdef CONFIG_PPC_ISERIES
 /* __raw_* accessors aren't supported on iSeries */
diff --git a/arch/powerpc/platforms/iseries/iommu.h b/include/asm-powerpc/iseries/iommu.h
similarity index 90%
rename from arch/powerpc/platforms/iseries/iommu.h
rename to include/asm-powerpc/iseries/iommu.h
index cb5658f..0edbfe1 100644
--- a/arch/powerpc/platforms/iseries/iommu.h
+++ b/include/asm-powerpc/iseries/iommu.h
@@ -1,5 +1,5 @@
-#ifndef _PLATFORMS_ISERIES_IOMMU_H
-#define _PLATFORMS_ISERIES_IOMMU_H
+#ifndef _ASM_POWERPC_ISERIES_IOMMU_H
+#define _ASM_POWERPC_ISERIES_IOMMU_H
 
 /*
  * Copyright (C) 2005  Stephen Rothwell, IBM Corporation
@@ -32,4 +32,4 @@
 		unsigned char slotno, unsigned char virtbus,
 		struct iommu_table *tbl);
 
-#endif /* _PLATFORMS_ISERIES_IOMMU_H */
+#endif /* _ASM_POWERPC_ISERIES_IOMMU_H */
diff --git a/include/asm-powerpc/kdump.h b/include/asm-powerpc/kdump.h
index a87aed0..5a5c3b5 100644
--- a/include/asm-powerpc/kdump.h
+++ b/include/asm-powerpc/kdump.h
@@ -1,13 +1,38 @@
 #ifndef _PPC64_KDUMP_H
 #define _PPC64_KDUMP_H
 
+/* Kdump kernel runs at 32 MB, change at your peril. */
+#define KDUMP_KERNELBASE	0x2000000
+
 /* How many bytes to reserve at zero for kdump. The reserve limit should
- * be greater or equal to the trampoline's end address. */
+ * be greater or equal to the trampoline's end address.
+ * Reserve to the end of the FWNMI area, see head_64.S */
 #define KDUMP_RESERVE_LIMIT	0x8000
 
+#ifdef CONFIG_CRASH_DUMP
+
+#define PHYSICAL_START	KDUMP_KERNELBASE
 #define KDUMP_TRAMPOLINE_START	0x0100
 #define KDUMP_TRAMPOLINE_END	0x3000
 
-extern void kdump_setup(void);
+#else /* !CONFIG_CRASH_DUMP */
+
+#define PHYSICAL_START	0x0
+
+#endif /* CONFIG_CRASH_DUMP */
+
+#ifndef __ASSEMBLY__
+#ifdef CONFIG_CRASH_DUMP
+
+extern void reserve_kdump_trampoline(void);
+extern void setup_kdump_trampoline(void);
+
+#else /* !CONFIG_CRASH_DUMP */
+
+static inline void reserve_kdump_trampoline(void) { ; }
+static inline void setup_kdump_trampoline(void) { ; }
+
+#endif /* CONFIG_CRASH_DUMP */
+#endif /* __ASSEMBLY__ */
 
 #endif /* __PPC64_KDUMP_H */
diff --git a/include/asm-powerpc/kexec.h b/include/asm-powerpc/kexec.h
index 6a2af2f..efe8872 100644
--- a/include/asm-powerpc/kexec.h
+++ b/include/asm-powerpc/kexec.h
@@ -31,9 +31,10 @@
 #define KEXEC_ARCH KEXEC_ARCH_PPC
 #endif
 
+#ifndef __ASSEMBLY__
+
 #ifdef CONFIG_KEXEC
 
-#ifndef __ASSEMBLY__
 #ifdef __powerpc64__
 /*
  * This function is responsible for capturing register states if coming
@@ -123,8 +124,19 @@
 extern void default_machine_crash_shutdown(struct pt_regs *regs);
 
 extern void machine_kexec_simple(struct kimage *image);
+extern int overlaps_crashkernel(unsigned long start, unsigned long size);
+extern void reserve_crashkernel(void);
 
-#endif /* ! __ASSEMBLY__ */
+#else /* !CONFIG_KEXEC */
+
+static inline int overlaps_crashkernel(unsigned long start, unsigned long size)
+{
+	return 0;
+}
+
+static inline void reserve_crashkernel(void) { ; }
+
 #endif /* CONFIG_KEXEC */
+#endif /* ! __ASSEMBLY__ */
 #endif /* __KERNEL__ */
 #endif /* _ASM_POWERPC_KEXEC_H */
diff --git a/include/asm-powerpc/page.h b/include/asm-powerpc/page.h
index 2fbeceb..ae610b6 100644
--- a/include/asm-powerpc/page.h
+++ b/include/asm-powerpc/page.h
@@ -13,6 +13,7 @@
 #ifdef __KERNEL__
 #include <linux/config.h>
 #include <asm/asm-compat.h>
+#include <asm/kdump.h>
 
 /*
  * On PPC32 page size is 4K. For PPC64 we support either 4K or 64K software
@@ -52,13 +53,6 @@
  * If you want to test if something's a kernel address, use is_kernel_addr().
  */
 
-#ifdef CONFIG_CRASH_DUMP
-/* Kdump kernel runs at 32 MB, change at your peril. */
-#define PHYSICAL_START	0x2000000
-#else
-#define PHYSICAL_START	0x0
-#endif
-
 #define PAGE_OFFSET     ASM_CONST(CONFIG_KERNEL_START)
 #define KERNELBASE      (PAGE_OFFSET + PHYSICAL_START)
 
diff --git a/include/asm-powerpc/prom.h b/include/asm-powerpc/prom.h
index 97ef1cd..c79d58a 100644
--- a/include/asm-powerpc/prom.h
+++ b/include/asm-powerpc/prom.h
@@ -230,6 +230,12 @@
 extern int of_pci_address_to_resource(struct device_node *dev, int bar,
 				      struct resource *r);
 
+/* Parse the ibm,dma-window property of an OF node into the busno, phys and
+ * size parameters.
+ */
+void of_parse_dma_window(struct device_node *dn, unsigned char *dma_window_prop,
+		unsigned long *busno, unsigned long *phys, unsigned long *size);
+
 extern void kdump_move_device_tree(void);
 
 #endif /* __KERNEL__ */
diff --git a/include/asm-powerpc/reg.h b/include/asm-powerpc/reg.h
index bd467bf..0257189 100644
--- a/include/asm-powerpc/reg.h
+++ b/include/asm-powerpc/reg.h
@@ -153,7 +153,7 @@
 #define SPRN_DABR	0x3F5	/* Data Address Breakpoint Register */
 #define   DABR_TRANSLATION	(1UL << 2)
 #define SPRN_DAR	0x013	/* Data Address Register */
-#define	SPRN_DSISR	0x012	/* Data Storage Interrupt Status Register */
+#define SPRN_DSISR	0x012	/* Data Storage Interrupt Status Register */
 #define   DSISR_NOHPTE		0x40000000	/* no translation found */
 #define   DSISR_PROTFAULT	0x08000000	/* protection fault */
 #define   DSISR_ISSTORE		0x02000000	/* access was a store */
@@ -258,16 +258,16 @@
 #define SPRN_IABR	0x3F2	/* Instruction Address Breakpoint Register */
 #define SPRN_HID4	0x3F4		/* 970 HID4 */
 #define SPRN_HID5	0x3F6		/* 970 HID5 */
-#define	SPRN_HID6	0x3F9	/* BE HID 6 */
-#define	  HID6_LB	(0x0F<<12) /* Concurrent Large Page Modes */
-#define	  HID6_DLP	(1<<20)	/* Disable all large page modes (4K only) */
-#define	SPRN_TSC_CELL	0x399	/* Thread switch control on Cell */
-#define	  TSC_CELL_DEC_ENABLE_0	0x400000 /* Decrementer Interrupt */
-#define	  TSC_CELL_DEC_ENABLE_1	0x200000 /* Decrementer Interrupt */
-#define	  TSC_CELL_EE_ENABLE	0x100000 /* External Interrupt */
-#define	  TSC_CELL_EE_BOOST	0x080000 /* External Interrupt Boost */
-#define	SPRN_TSC 	0x3FD	/* Thread switch control on others */
-#define	SPRN_TST 	0x3FC	/* Thread switch timeout on others */
+#define SPRN_HID6	0x3F9	/* BE HID 6 */
+#define   HID6_LB	(0x0F<<12) /* Concurrent Large Page Modes */
+#define   HID6_DLP	(1<<20)	/* Disable all large page modes (4K only) */
+#define SPRN_TSC_CELL	0x399	/* Thread switch control on Cell */
+#define   TSC_CELL_DEC_ENABLE_0	0x400000 /* Decrementer Interrupt */
+#define   TSC_CELL_DEC_ENABLE_1	0x200000 /* Decrementer Interrupt */
+#define   TSC_CELL_EE_ENABLE	0x100000 /* External Interrupt */
+#define   TSC_CELL_EE_BOOST	0x080000 /* External Interrupt Boost */
+#define SPRN_TSC 	0x3FD	/* Thread switch control on others */
+#define SPRN_TST 	0x3FC	/* Thread switch timeout on others */
 #if !defined(SPRN_IAC1) && !defined(SPRN_IAC2)
 #define SPRN_IAC1	0x3F4		/* Instruction Address Compare 1 */
 #define SPRN_IAC2	0x3F5		/* Instruction Address Compare 2 */
@@ -362,7 +362,7 @@
 #endif
 #define SPRN_PTEHI	0x3D5	/* 981 7450 PTE HI word (S/W TLB load) */
 #define SPRN_PTELO	0x3D6	/* 982 7450 PTE LO word (S/W TLB load) */
-#define	SPRN_PURR	0x135	/* Processor Utilization of Resources Reg */
+#define SPRN_PURR	0x135	/* Processor Utilization of Resources Reg */
 #define SPRN_PVR	0x11F	/* Processor Version Register */
 #define SPRN_RPA	0x3D6	/* Required Physical Address Register */
 #define SPRN_SDA	0x3BF	/* Sampled Data Address Register */
@@ -559,20 +559,20 @@
 
 /* 64-bit processors */
 /* XXX the prefix should be PVR_, we'll do a global sweep to fix it one day */
-#define	PV_NORTHSTAR	0x0033
-#define	PV_PULSAR	0x0034
-#define	PV_POWER4	0x0035
-#define	PV_ICESTAR	0x0036
-#define	PV_SSTAR	0x0037
-#define	PV_POWER4p	0x0038
+#define PV_NORTHSTAR	0x0033
+#define PV_PULSAR	0x0034
+#define PV_POWER4	0x0035
+#define PV_ICESTAR	0x0036
+#define PV_SSTAR	0x0037
+#define PV_POWER4p	0x0038
 #define PV_970		0x0039
-#define	PV_POWER5	0x003A
+#define PV_POWER5	0x003A
 #define PV_POWER5p	0x003B
 #define PV_970FX	0x003C
-#define	PV_630		0x0040
-#define	PV_630p	0x0041
-#define	PV_970MP	0x0044
-#define	PV_BE		0x0070
+#define PV_630		0x0040
+#define PV_630p	0x0041
+#define PV_970MP	0x0044
+#define PV_BE		0x0070
 
 /*
  * Number of entries in the SLB. If this ever changes we should handle
diff --git a/include/asm-powerpc/tce.h b/include/asm-powerpc/tce.h
index 6fa200a..c9483ad 100644
--- a/include/asm-powerpc/tce.h
+++ b/include/asm-powerpc/tce.h
@@ -35,32 +35,15 @@
 #define TCE_PAGE_SIZE	(1 << TCE_SHIFT)
 #define TCE_PAGE_FACTOR	(PAGE_SHIFT - TCE_SHIFT)
 
+#define TCE_ENTRY_SIZE		8		/* each TCE is 64 bits */
 
-/* tce_entry
- * Used by pSeries (SMP) and iSeries/pSeries LPAR, but there it's
- * abstracted so layout is irrelevant.
- */
-union tce_entry {
-   	unsigned long te_word;
-	struct {
-		unsigned int  tb_cacheBits :6;	/* Cache hash bits - not used */
-		unsigned int  tb_rsvd      :6;
-		unsigned long tb_rpn       :40;	/* Real page number */
-		unsigned int  tb_valid     :1;	/* Tce is valid (vb only) */
-		unsigned int  tb_allio     :1;	/* Tce is valid for all lps (vb only) */
-		unsigned int  tb_lpindex   :8;	/* LpIndex for user of TCE (vb only) */
-		unsigned int  tb_pciwr     :1;	/* Write allowed (pci only) */
-		unsigned int  tb_rdwr      :1;	/* Read allowed  (pci), Write allowed (vb) */
-	} te_bits;
-#define te_cacheBits te_bits.tb_cacheBits
-#define te_rpn       te_bits.tb_rpn
-#define te_valid     te_bits.tb_valid
-#define te_allio     te_bits.tb_allio
-#define te_lpindex   te_bits.tb_lpindex
-#define te_pciwr     te_bits.tb_pciwr
-#define te_rdwr      te_bits.tb_rdwr
-};
-
+#define TCE_RPN_MASK		0xfffffffffful  /* 40-bit RPN (4K pages) */
+#define TCE_RPN_SHIFT		12
+#define TCE_VALID		0x800		/* TCE valid */
+#define TCE_ALLIO		0x400		/* TCE valid for all lpars */
+#define TCE_PCI_WRITE		0x2		/* write from PCI allowed */
+#define TCE_PCI_READ		0x1		/* read from PCI allowed */
+#define TCE_VB_WRITE		0x1		/* write from VB allowed */
 
 #endif /* __KERNEL__ */
 #endif /* _ASM_POWERPC_TCE_H */
diff --git a/include/asm-powerpc/udbg.h b/include/asm-powerpc/udbg.h
index 5c4236c3..19a1517 100644
--- a/include/asm-powerpc/udbg.h
+++ b/include/asm-powerpc/udbg.h
@@ -23,7 +23,8 @@
 extern int udbg_read(char *buf, int buflen);
 
 extern void register_early_udbg_console(void);
-extern void udbg_printf(const char *fmt, ...);
+extern void udbg_printf(const char *fmt, ...)
+	__attribute__ ((format (printf, 1, 2)));
 extern void udbg_progress(char *s, unsigned short hex);
 
 extern void udbg_init_uart(void __iomem *comport, unsigned int speed,
diff --git a/include/asm-powerpc/vio.h b/include/asm-powerpc/vio.h
index 0544ece..10da7f3 100644
--- a/include/asm-powerpc/vio.h
+++ b/include/asm-powerpc/vio.h
@@ -64,32 +64,22 @@
 	struct device_driver driver;
 };
 
-struct vio_bus_ops {
-	int (*match)(const struct vio_device_id *id, const struct vio_dev *dev);
-	void (*unregister_device)(struct vio_dev *);
-	void (*release_device)(struct device *);
-};
-
 extern struct dma_mapping_ops vio_dma_ops;
 extern struct bus_type vio_bus_type;
-extern struct vio_dev vio_bus_device;
 
 extern int vio_register_driver(struct vio_driver *drv);
 extern void vio_unregister_driver(struct vio_driver *drv);
 
-extern struct vio_dev * __devinit vio_register_device(struct vio_dev *viodev);
 extern void __devinit vio_unregister_device(struct vio_dev *dev);
 
-extern int vio_bus_init(struct vio_bus_ops *);
-
-#ifdef CONFIG_PPC_PSERIES
 struct device_node;
 
 extern struct vio_dev * __devinit vio_register_device_node(
 		struct device_node *node_vdev);
-extern struct vio_dev *vio_find_node(struct device_node *vnode);
-extern const void *vio_get_attribute(struct vio_dev *vdev, void *which,
+extern const void *vio_get_attribute(struct vio_dev *vdev, char *which,
 		int *length);
+#ifdef CONFIG_PPC_PSERIES
+extern struct vio_dev *vio_find_node(struct device_node *vnode);
 extern int vio_enable_interrupts(struct vio_dev *dev);
 extern int vio_disable_interrupts(struct vio_dev *dev);
 #endif
diff --git a/include/asm-ppc/mpc85xx.h b/include/asm-ppc/mpc85xx.h
index f47002a..4f844eb 100644
--- a/include/asm-ppc/mpc85xx.h
+++ b/include/asm-ppc/mpc85xx.h
@@ -28,6 +28,9 @@
 #if defined(CONFIG_MPC8555_CDS) || defined(CONFIG_MPC8548_CDS)
 #include <platforms/85xx/mpc8555_cds.h>
 #endif
+#ifdef CONFIG_MPC85xx_CDS
+#include <platforms/85xx/mpc85xx_cds.h>
+#endif
 #ifdef CONFIG_MPC8560_ADS
 #include <platforms/85xx/mpc8560_ads.h>
 #endif