diff --git a/Documentation/devicetree/bindings/powerpc/fsl/raideng.txt b/Documentation/devicetree/bindings/powerpc/fsl/raideng.txt
new file mode 100644
index 0000000..4ad29b9
--- /dev/null
+++ b/Documentation/devicetree/bindings/powerpc/fsl/raideng.txt
@@ -0,0 +1,81 @@
+* Freescale 85xx RAID Engine nodes
+
+RAID Engine nodes are defined to describe on-chip RAID accelerators.  Each RAID
+Engine should have a separate node.
+
+Supported chips:
+P5020, P5040
+
+Required properties:
+
+- compatible:	Should contain "fsl,raideng-v1.0" as the value
+		This identifies RAID Engine block. 1 in 1.0 represents
+		major number whereas 0 represents minor number. The
+		version matches the hardware IP version.
+- reg:		offset and length of the register set for the device
+- ranges:	standard ranges property specifying the translation
+		between child address space and parent address space
+
+Example:
+	/* P5020 */
+	raideng: raideng@320000 {
+		compatible = "fsl,raideng-v1.0";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg	= <0x320000 0x10000>;
+		ranges	= <0 0x320000 0x10000>;
+	};
+
+
+There must be a sub-node for each job queue present in RAID Engine
+This node must be a sub-node of the main RAID Engine node
+
+- compatible:	Should contain "fsl,raideng-v1.0-job-queue" as the value
+		This identifies the job queue interface
+- reg:		offset and length of the register set for job queue
+- ranges:	standard ranges property specifying the translation
+		between child address space and parent address space
+
+Example:
+	/* P5020 */
+	raideng_jq0@1000 {
+		compatible = "fsl,raideng-v1.0-job-queue";
+		reg	   = <0x1000 0x1000>;
+		ranges	   = <0x0 0x1000 0x1000>;
+	};
+
+
+There must be a sub-node for each job ring present in RAID Engine
+This node must be a sub-node of job queue node
+
+- compatible:	Must contain "fsl,raideng-v1.0-job-ring" as the value
+		This identifies job ring. Should contain either
+		"fsl,raideng-v1.0-hp-ring" or "fsl,raideng-v1.0-lp-ring"
+		depending upon whether ring has high or low priority
+- reg:		offset and length of the register set for job ring
+- interrupts:	interrupt mapping for job ring IRQ
+
+Optional property:
+
+- fsl,liodn:	Specifies the LIODN to be used for Job Ring. This
+		property is normally set by firmware. Value
+		is of 12-bits which is the LIODN number for this JR.
+		This property is used by the IOMMU (PAMU) to distinquish
+		transactions from this JR and than be able to do address
+		translation & protection accordingly.
+
+Example:
+	/* P5020 */
+	raideng_jq0@1000 {
+		compatible = "fsl,raideng-v1.0-job-queue";
+		reg	   = <0x1000 0x1000>;
+		ranges	   = <0x0 0x1000 0x1000>;
+
+		raideng_jr0: jr@0 {
+			compatible = "fsl,raideng-v1.0-job-ring", "fsl,raideng-v1.0-hp-ring";
+			reg	   = <0x0 0x400>;
+			interrupts = <139 2 0 0>;
+			interrupt-parent = <&mpic>;
+			fsl,liodn = <0x41>;
+		};
+	};
diff --git a/arch/powerpc/boot/dts/fsl/p5020si-post.dtsi b/arch/powerpc/boot/dts/fsl/p5020si-post.dtsi
index 64b6abe..5d7205b 100644
--- a/arch/powerpc/boot/dts/fsl/p5020si-post.dtsi
+++ b/arch/powerpc/boot/dts/fsl/p5020si-post.dtsi
@@ -354,4 +354,5 @@
 /include/ "qoriq-sata2-0.dtsi"
 /include/ "qoriq-sata2-1.dtsi"
 /include/ "qoriq-sec4.2-0.dtsi"
+/include/ "qoriq-raid1.0-0.dtsi"
 };
diff --git a/arch/powerpc/boot/dts/fsl/p5020si-pre.dtsi b/arch/powerpc/boot/dts/fsl/p5020si-pre.dtsi
index 0a198b0..8df47fc 100644
--- a/arch/powerpc/boot/dts/fsl/p5020si-pre.dtsi
+++ b/arch/powerpc/boot/dts/fsl/p5020si-pre.dtsi
@@ -73,6 +73,12 @@
 		rtic_c = &rtic_c;
 		rtic_d = &rtic_d;
 		sec_mon = &sec_mon;
+
+		raideng = &raideng;
+		raideng_jr0 = &raideng_jr0;
+		raideng_jr1 = &raideng_jr1;
+		raideng_jr2 = &raideng_jr2;
+		raideng_jr3 = &raideng_jr3;
 	};
 
 	cpus {
diff --git a/arch/powerpc/boot/dts/fsl/qoriq-raid1.0-0.dtsi b/arch/powerpc/boot/dts/fsl/qoriq-raid1.0-0.dtsi
new file mode 100644
index 0000000..8d2e8aa
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/qoriq-raid1.0-0.dtsi
@@ -0,0 +1,85 @@
+/*
+ * QorIQ RAID 1.0 device tree stub [ controller @ offset 0x320000 ]
+ *
+ * Copyright 2012 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+raideng: raideng@320000 {
+	compatible = "fsl,raideng-v1.0";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	reg = <0x320000 0x10000>;
+	ranges = <0 0x320000 0x10000>;
+
+	raideng_jq0@1000 {
+		compatible = "fsl,raideng-v1.0-job-queue";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x1000 0x1000>;
+		ranges = <0x0 0x1000 0x1000>;
+
+		raideng_jr0: jr@0 {
+			compatible = "fsl,raideng-v1.0-job-ring", "fsl,raideng-v1.0-hp-ring";
+			reg = <0x0 0x400>;
+			interrupts = <139 2 0 0>;
+			interrupt-parent = <&mpic>;
+		};
+
+		raideng_jr1: jr@400 {
+			compatible = "fsl,raideng-v1.0-job-ring", "fsl,raideng-v1.0-lp-ring";
+			reg = <0x400 0x400>;
+			interrupts = <140 2 0 0>;
+			interrupt-parent = <&mpic>;
+		};
+	};
+
+	raideng_jq1@2000 {
+		compatible = "fsl,raideng-v1.0-job-queue";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x2000 0x1000>;
+		ranges = <0x0 0x2000 0x1000>;
+
+		raideng_jr2: jr@0 {
+			compatible = "fsl,raideng-v1.0-job-ring", "fsl,raideng-v1.0-hp-ring";
+			reg = <0x0 0x400>;
+			interrupts = <141 2 0 0>;
+			interrupt-parent = <&mpic>;
+		};
+
+		raideng_jr3: jr@400 {
+			compatible = "fsl,raideng-v1.0-job-ring", "fsl,raideng-v1.0-lp-ring";
+			reg = <0x400 0x400>;
+			interrupts = <142 2 0 0>;
+			interrupt-parent = <&mpic>;
+		};
+	};
+};
diff --git a/arch/powerpc/include/asm/fsl_guts.h b/arch/powerpc/include/asm/fsl_guts.h
index dd5ba2c..77ced0b 100644
--- a/arch/powerpc/include/asm/fsl_guts.h
+++ b/arch/powerpc/include/asm/fsl_guts.h
@@ -71,7 +71,9 @@
 	u8	res0c4[0x224 - 0xc4];
 	__be32  iodelay1;	/* 0x.0224 - IO delay control register 1 */
 	__be32  iodelay2;	/* 0x.0228 - IO delay control register 2 */
-	u8	res22c[0x800 - 0x22c];
+	u8	res22c[0x604 - 0x22c];
+	__be32	pamubypenr; 	/* 0x.604 - PAMU bypass enable register */
+	u8	res608[0x800 - 0x608];
 	__be32	clkdvdr;	/* 0x.0800 - Clock Divide Register */
 	u8	res804[0x900 - 0x804];
 	__be32	ircr;		/* 0x.0900 - Infrared Control Register */
diff --git a/arch/powerpc/platforms/85xx/p1022_ds.c b/arch/powerpc/platforms/85xx/p1022_ds.c
index 8fb1257..7328b8d 100644
--- a/arch/powerpc/platforms/85xx/p1022_ds.c
+++ b/arch/powerpc/platforms/85xx/p1022_ds.c
@@ -249,7 +249,7 @@
 		goto exit;
 	}
 
-	iprop = of_get_property(law_node, "fsl,num-laws", 0);
+	iprop = of_get_property(law_node, "fsl,num-laws", NULL);
 	if (!iprop) {
 		pr_err("p1022ds: LAW node is missing fsl,num-laws property\n");
 		goto exit;
diff --git a/arch/powerpc/platforms/85xx/smp.c b/arch/powerpc/platforms/85xx/smp.c
index 6fcfa12..148c2f2 100644
--- a/arch/powerpc/platforms/85xx/smp.c
+++ b/arch/powerpc/platforms/85xx/smp.c
@@ -128,6 +128,19 @@
 }
 #endif
 
+static inline void flush_spin_table(void *spin_table)
+{
+	flush_dcache_range((ulong)spin_table,
+		(ulong)spin_table + sizeof(struct epapr_spin_table));
+}
+
+static inline u32 read_spin_table_addr_l(void *spin_table)
+{
+	flush_dcache_range((ulong)spin_table,
+		(ulong)spin_table + sizeof(struct epapr_spin_table));
+	return in_be32(&((struct epapr_spin_table *)spin_table)->addr_l);
+}
+
 static int __cpuinit smp_85xx_kick_cpu(int nr)
 {
 	unsigned long flags;
@@ -161,8 +174,8 @@
 
 	/* Map the spin table */
 	if (ioremappable)
-		spin_table = ioremap(*cpu_rel_addr,
-				sizeof(struct epapr_spin_table));
+		spin_table = ioremap_prot(*cpu_rel_addr,
+			sizeof(struct epapr_spin_table), _PAGE_COHERENT);
 	else
 		spin_table = phys_to_virt(*cpu_rel_addr);
 
@@ -173,7 +186,16 @@
 	generic_set_cpu_up(nr);
 
 	if (system_state == SYSTEM_RUNNING) {
+		/*
+		 * To keep it compatible with old boot program which uses
+		 * cache-inhibit spin table, we need to flush the cache
+		 * before accessing spin table to invalidate any staled data.
+		 * We also need to flush the cache after writing to spin
+		 * table to push data out.
+		 */
+		flush_spin_table(spin_table);
 		out_be32(&spin_table->addr_l, 0);
+		flush_spin_table(spin_table);
 
 		/*
 		 * We don't set the BPTR register here since it already points
@@ -181,9 +203,14 @@
 		 */
 		mpic_reset_core(hw_cpu);
 
-		/* wait until core is ready... */
-		if (!spin_event_timeout(in_be32(&spin_table->addr_l) == 1,
-						10000, 100)) {
+		/*
+		 * wait until core is ready...
+		 * We need to invalidate the stale data, in case the boot
+		 * loader uses a cache-inhibited spin table.
+		 */
+		if (!spin_event_timeout(
+				read_spin_table_addr_l(spin_table) == 1,
+				10000, 100)) {
 			pr_err("%s: timeout waiting for core %d to reset\n",
 							__func__, hw_cpu);
 			ret = -ENOENT;
@@ -194,12 +221,10 @@
 		__secondary_hold_acknowledge = -1;
 	}
 #endif
+	flush_spin_table(spin_table);
 	out_be32(&spin_table->pir, hw_cpu);
 	out_be32(&spin_table->addr_l, __pa(__early_start));
-
-	if (!ioremappable)
-		flush_dcache_range((ulong)spin_table,
-			(ulong)spin_table + sizeof(struct epapr_spin_table));
+	flush_spin_table(spin_table);
 
 	/* Wait a bit for the CPU to ack. */
 	if (!spin_event_timeout(__secondary_hold_acknowledge == hw_cpu,
@@ -213,13 +238,11 @@
 #else
 	smp_generic_kick_cpu(nr);
 
+	flush_spin_table(spin_table);
 	out_be32(&spin_table->pir, hw_cpu);
 	out_be64((u64 *)(&spin_table->addr_h),
 	  __pa((u64)*((unsigned long long *)generic_secondary_smp_init)));
-
-	if (!ioremappable)
-		flush_dcache_range((ulong)spin_table,
-			(ulong)spin_table + sizeof(struct epapr_spin_table));
+	flush_spin_table(spin_table);
 #endif
 
 	local_irq_restore(flags);
diff --git a/arch/powerpc/platforms/86xx/mpc8610_hpcd.c b/arch/powerpc/platforms/86xx/mpc8610_hpcd.c
index a817398..04d9d31 100644
--- a/arch/powerpc/platforms/86xx/mpc8610_hpcd.c
+++ b/arch/powerpc/platforms/86xx/mpc8610_hpcd.c
@@ -353,5 +353,7 @@
 	.time_init		= mpc86xx_time_init,
 	.calibrate_decr		= generic_calibrate_decr,
 	.progress		= udbg_progress,
+#ifdef CONFIG_PCI
 	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+#endif
 };
diff --git a/arch/powerpc/sysdev/fsl_pci.c b/arch/powerpc/sysdev/fsl_pci.c
index ffb93ae..b96885b 100644
--- a/arch/powerpc/sysdev/fsl_pci.c
+++ b/arch/powerpc/sysdev/fsl_pci.c
@@ -89,7 +89,7 @@
 	return 0;
 }
 
-static int __init setup_one_atmu(struct ccsr_pci __iomem *pci,
+static int setup_one_atmu(struct ccsr_pci __iomem *pci,
 	unsigned int index, const struct resource *res,
 	resource_size_t offset)
 {
@@ -126,7 +126,7 @@
 }
 
 /* atmu setup for fsl pci/pcie controller */
-static void __init setup_pci_atmu(struct pci_controller *hose,
+static void setup_pci_atmu(struct pci_controller *hose,
 				  struct resource *rsrc)
 {
 	struct ccsr_pci __iomem *pci;
@@ -902,9 +902,42 @@
 	return 0;
 }
 
+#ifdef CONFIG_PM
+static int fsl_pci_resume(struct device *dev)
+{
+	struct pci_controller *hose;
+	struct resource pci_rsrc;
+
+	hose = pci_find_hose_for_OF_device(dev->of_node);
+	if (!hose)
+		return -ENODEV;
+
+	if (of_address_to_resource(dev->of_node, 0, &pci_rsrc)) {
+		dev_err(dev, "Get pci register base failed.");
+		return -ENODEV;
+	}
+
+	setup_pci_atmu(hose, &pci_rsrc);
+
+	return 0;
+}
+
+static const struct dev_pm_ops pci_pm_ops = {
+	.resume = fsl_pci_resume,
+};
+
+#define PCI_PM_OPS (&pci_pm_ops)
+
+#else
+
+#define PCI_PM_OPS NULL
+
+#endif
+
 static struct platform_driver fsl_pci_driver = {
 	.driver = {
 		.name = "fsl-pci",
+		.pm = PCI_PM_OPS,
 		.of_match_table = pci_ids,
 	},
 	.probe = fsl_pci_probe,
diff --git a/drivers/virt/fsl_hypervisor.c b/drivers/virt/fsl_hypervisor.c
index 4939e0c..d294f67 100644
--- a/drivers/virt/fsl_hypervisor.c
+++ b/drivers/virt/fsl_hypervisor.c
@@ -796,9 +796,6 @@
 	struct device_node *node;
 	int ret;
 
-	if (!(mfmsr() & MSR_GS))
-		return 0;
-
 	node = of_find_node_by_path("/hypervisor");
 	if (!node)
 		return 0;