Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm: (37 commits)
ARM: 5673/1: U300 fix initsection compile warning
ARM: Fix broken highmem support
mx31moboard: invert sdhc ro signal sense
ARM: S3C24XX: Fix clkout mpx error
ARM: S3C64XX: serial: Fix a typo in Kconfig
IXP4xx: Fix IO_SPACE_LIMIT for 2.6.31-rc core PCI changes
OMAP3: RX51: Updated rx51_defconfig
OMAP2/3: mmc-twl4030: Free up MMC regulators while cleaning up
OMAP3: RX51: Define TWL4030 USB transceiver in board file
OMAP3: Overo: Fix smsc911x platform device resource value
OMAP3: Fix omap3 sram virtual addres overlap vmalloc space after increasing vmalloc size
OMAP2/3: DMA errata correction
OMAP: Fix testing of cpu defines for mach-omap1
OMAP3: Overo: add missing pen-down GPIO definition
OMAP: GPIO: clear/restore level/edge detect settings on mask/unmask
OMAP3: PM: Fix wrong sequence in suspend.
OMAP: PM: CPUfreq: obey min/max settings of policy
OMAP2/3/4: UART: allow in-order port traversal
OMAP2/3/4: UART: Allow per-UART disabling wakeup for serial ports
OMAP3: Fixed crash bug with serial + suspend
...
diff --git a/arch/arm/configs/rx51_defconfig b/arch/arm/configs/rx51_defconfig
index eb2cb31..f238df6 100644
--- a/arch/arm/configs/rx51_defconfig
+++ b/arch/arm/configs/rx51_defconfig
@@ -282,7 +282,7 @@
#
CONFIG_ZBOOT_ROM_TEXT=0x0
CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="init=/sbin/preinit ubi.mtd=rootfs root=ubi0:rootfs rootfstype=ubifs rootflags=bulk_read,no_chk_data_crc rw console=ttyMTD,log console=tty0"
+CONFIG_CMDLINE="init=/sbin/preinit ubi.mtd=rootfs root=ubi0:rootfs rootfstype=ubifs rootflags=bulk_read,no_chk_data_crc rw console=ttyMTD,log console=tty0 console=ttyS2,115200n8"
# CONFIG_XIP_KERNEL is not set
# CONFIG_KEXEC is not set
@@ -1354,7 +1354,7 @@
# CONFIG_USB_GPIO_VBUS is not set
# CONFIG_ISP1301_OMAP is not set
CONFIG_TWL4030_USB=y
-CONFIG_MMC=m
+CONFIG_MMC=y
# CONFIG_MMC_DEBUG is not set
# CONFIG_MMC_UNSAFE_RESUME is not set
@@ -1449,7 +1449,8 @@
# on-CPU RTC drivers
#
# CONFIG_DMADEVICES is not set
-# CONFIG_REGULATOR is not set
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_TWL4030=y
# CONFIG_UIO is not set
# CONFIG_STAGING is not set
diff --git a/arch/arm/include/asm/setup.h b/arch/arm/include/asm/setup.h
index ee1304f..5ccce0a 100644
--- a/arch/arm/include/asm/setup.h
+++ b/arch/arm/include/asm/setup.h
@@ -201,7 +201,8 @@
struct membank {
unsigned long start;
unsigned long size;
- int node;
+ unsigned short node;
+ unsigned short highmem;
};
struct meminfo {
diff --git a/arch/arm/mach-ixp4xx/include/mach/io.h b/arch/arm/mach-ixp4xx/include/mach/io.h
index ce63048..8a947d4 100644
--- a/arch/arm/mach-ixp4xx/include/mach/io.h
+++ b/arch/arm/mach-ixp4xx/include/mach/io.h
@@ -17,7 +17,7 @@
#include <mach/hardware.h>
-#define IO_SPACE_LIMIT 0xffff0000
+#define IO_SPACE_LIMIT 0x0000ffff
extern int (*ixp4xx_pci_read)(u32 addr, u32 cmd, u32* data);
extern int ixp4xx_pci_write(u32 addr, u32 cmd, u32 data);
diff --git a/arch/arm/mach-mx3/mx31moboard-devboard.c b/arch/arm/mach-mx3/mx31moboard-devboard.c
index 4704405..b48581e 100644
--- a/arch/arm/mach-mx3/mx31moboard-devboard.c
+++ b/arch/arm/mach-mx3/mx31moboard-devboard.c
@@ -63,7 +63,7 @@
static int devboard_sdhc2_get_ro(struct device *dev)
{
- return gpio_get_value(SDHC2_WP);
+ return !gpio_get_value(SDHC2_WP);
}
static int devboard_sdhc2_init(struct device *dev, irq_handler_t detect_irq,
diff --git a/arch/arm/mach-mx3/mx31moboard-marxbot.c b/arch/arm/mach-mx3/mx31moboard-marxbot.c
index 641c3d6..901fb01 100644
--- a/arch/arm/mach-mx3/mx31moboard-marxbot.c
+++ b/arch/arm/mach-mx3/mx31moboard-marxbot.c
@@ -67,7 +67,7 @@
static int marxbot_sdhc2_get_ro(struct device *dev)
{
- return gpio_get_value(SDHC2_WP);
+ return !gpio_get_value(SDHC2_WP);
}
static int marxbot_sdhc2_init(struct device *dev, irq_handler_t detect_irq,
diff --git a/arch/arm/mach-mx3/mx31moboard.c b/arch/arm/mach-mx3/mx31moboard.c
index a17f2e4..2a2da47 100644
--- a/arch/arm/mach-mx3/mx31moboard.c
+++ b/arch/arm/mach-mx3/mx31moboard.c
@@ -94,7 +94,7 @@
static int moboard_sdhc1_get_ro(struct device *dev)
{
- return gpio_get_value(SDHC1_WP);
+ return !gpio_get_value(SDHC1_WP);
}
static int moboard_sdhc1_init(struct device *dev, irq_handler_t detect_irq,
diff --git a/arch/arm/mach-mx3/pcm037_eet.c b/arch/arm/mach-mx3/pcm037_eet.c
index fe52fb1..8d38600 100644
--- a/arch/arm/mach-mx3/pcm037_eet.c
+++ b/arch/arm/mach-mx3/pcm037_eet.c
@@ -24,15 +24,6 @@
#include "devices.h"
static unsigned int pcm037_eet_pins[] = {
- /* SPI #1 */
- MX31_PIN_CSPI1_MISO__MISO,
- MX31_PIN_CSPI1_MOSI__MOSI,
- MX31_PIN_CSPI1_SCLK__SCLK,
- MX31_PIN_CSPI1_SPI_RDY__SPI_RDY,
- MX31_PIN_CSPI1_SS0__SS0,
- MX31_PIN_CSPI1_SS1__SS1,
- MX31_PIN_CSPI1_SS2__SS2,
-
/* Reserve and hardwire GPIO 57 high - S6E63D6 chipselect */
IOMUX_MODE(MX31_PIN_KEY_COL7, IOMUX_CONFIG_GPIO),
/* GPIO keys */
diff --git a/arch/arm/mach-omap2/board-2430sdp.c b/arch/arm/mach-omap2/board-2430sdp.c
index 9c3fdcd..8ec2a13 100644
--- a/arch/arm/mach-omap2/board-2430sdp.c
+++ b/arch/arm/mach-omap2/board-2430sdp.c
@@ -141,7 +141,7 @@
static void __init omap_2430sdp_init_irq(void)
{
- omap2_init_common_hw(NULL);
+ omap2_init_common_hw(NULL, NULL);
omap_init_irq();
omap_gpio_init();
}
diff --git a/arch/arm/mach-omap2/board-3430sdp.c b/arch/arm/mach-omap2/board-3430sdp.c
index 496a90e..ac262cd 100644
--- a/arch/arm/mach-omap2/board-3430sdp.c
+++ b/arch/arm/mach-omap2/board-3430sdp.c
@@ -169,7 +169,7 @@
static void __init omap_3430sdp_init_irq(void)
{
- omap2_init_common_hw(hyb18m512160af6_sdrc_params);
+ omap2_init_common_hw(hyb18m512160af6_sdrc_params, NULL);
omap_init_irq();
omap_gpio_init();
}
diff --git a/arch/arm/mach-omap2/board-4430sdp.c b/arch/arm/mach-omap2/board-4430sdp.c
index 57e477b..b0c7402 100644
--- a/arch/arm/mach-omap2/board-4430sdp.c
+++ b/arch/arm/mach-omap2/board-4430sdp.c
@@ -59,7 +59,7 @@
static void __init omap_4430sdp_init_irq(void)
{
- omap2_init_common_hw(NULL);
+ omap2_init_common_hw(NULL, NULL);
#ifdef CONFIG_OMAP_32K_TIMER
omap2_gp_clockevent_set_gptimer(1);
#endif
diff --git a/arch/arm/mach-omap2/board-apollon.c b/arch/arm/mach-omap2/board-apollon.c
index 06dfba8..dcfc20d 100644
--- a/arch/arm/mach-omap2/board-apollon.c
+++ b/arch/arm/mach-omap2/board-apollon.c
@@ -250,7 +250,7 @@
static void __init omap_apollon_init_irq(void)
{
- omap2_init_common_hw(NULL);
+ omap2_init_common_hw(NULL, NULL);
omap_init_irq();
omap_gpio_init();
apollon_init_smc91x();
diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach-omap2/board-generic.c
index 3492162..fd00aa0 100644
--- a/arch/arm/mach-omap2/board-generic.c
+++ b/arch/arm/mach-omap2/board-generic.c
@@ -33,7 +33,7 @@
static void __init omap_generic_init_irq(void)
{
- omap2_init_common_hw(NULL);
+ omap2_init_common_hw(NULL, NULL);
omap_init_irq();
}
diff --git a/arch/arm/mach-omap2/board-h4.c b/arch/arm/mach-omap2/board-h4.c
index e7d017c..7b1d61d 100644
--- a/arch/arm/mach-omap2/board-h4.c
+++ b/arch/arm/mach-omap2/board-h4.c
@@ -270,7 +270,7 @@
static void __init omap_h4_init_irq(void)
{
- omap2_init_common_hw(NULL);
+ omap2_init_common_hw(NULL, NULL);
omap_init_irq();
omap_gpio_init();
h4_init_flash();
diff --git a/arch/arm/mach-omap2/board-ldp.c b/arch/arm/mach-omap2/board-ldp.c
index d8bc0a7..ea383f8 100644
--- a/arch/arm/mach-omap2/board-ldp.c
+++ b/arch/arm/mach-omap2/board-ldp.c
@@ -270,7 +270,7 @@
static void __init omap_ldp_init_irq(void)
{
- omap2_init_common_hw(NULL);
+ omap2_init_common_hw(NULL, NULL);
omap_init_irq();
omap_gpio_init();
ldp_init_smsc911x();
diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c
index 991ac9c..e00ba12 100644
--- a/arch/arm/mach-omap2/board-omap3beagle.c
+++ b/arch/arm/mach-omap2/board-omap3beagle.c
@@ -282,7 +282,8 @@
static void __init omap3_beagle_init_irq(void)
{
- omap2_init_common_hw(mt46h32m32lf6_sdrc_params);
+ omap2_init_common_hw(mt46h32m32lf6_sdrc_params,
+ mt46h32m32lf6_sdrc_params);
omap_init_irq();
#ifdef CONFIG_OMAP_32K_TIMER
omap2_gp_clockevent_set_gptimer(12);
@@ -408,6 +409,10 @@
usb_musb_init();
omap3beagle_flash_init();
+
+ /* Ensure SDRC pins are mux'd for self-refresh */
+ omap_cfg_reg(H16_34XX_SDRC_CKE0);
+ omap_cfg_reg(H17_34XX_SDRC_CKE1);
}
static void __init omap3_beagle_map_io(void)
diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
index cf3dd77..c4b1446 100644
--- a/arch/arm/mach-omap2/board-omap3evm.c
+++ b/arch/arm/mach-omap2/board-omap3evm.c
@@ -280,7 +280,7 @@
static void __init omap3_evm_init_irq(void)
{
- omap2_init_common_hw(mt46h32m32lf6_sdrc_params);
+ omap2_init_common_hw(mt46h32m32lf6_sdrc_params, NULL);
omap_init_irq();
omap_gpio_init();
omap3evm_init_smc911x();
diff --git a/arch/arm/mach-omap2/board-omap3pandora.c b/arch/arm/mach-omap2/board-omap3pandora.c
index e32aa23..864ee3d 100644
--- a/arch/arm/mach-omap2/board-omap3pandora.c
+++ b/arch/arm/mach-omap2/board-omap3pandora.c
@@ -40,6 +40,7 @@
#include <mach/mcspi.h>
#include <mach/usb.h>
#include <mach/keypad.h>
+#include <mach/mux.h>
#include "sdram-micron-mt46h32m32lf-6.h"
#include "mmc-twl4030.h"
@@ -310,7 +311,8 @@
static void __init omap3pandora_init_irq(void)
{
- omap2_init_common_hw(mt46h32m32lf6_sdrc_params);
+ omap2_init_common_hw(mt46h32m32lf6_sdrc_params,
+ mt46h32m32lf6_sdrc_params);
omap_init_irq();
omap_gpio_init();
}
@@ -397,6 +399,10 @@
omap3pandora_ads7846_init();
pandora_keys_gpio_init();
usb_musb_init();
+
+ /* Ensure SDRC pins are mux'd for self-refresh */
+ omap_cfg_reg(H16_34XX_SDRC_CKE0);
+ omap_cfg_reg(H17_34XX_SDRC_CKE1);
}
static void __init omap3pandora_map_io(void)
diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c
index dff5528..6bce230 100644
--- a/arch/arm/mach-omap2/board-overo.c
+++ b/arch/arm/mach-omap2/board-overo.c
@@ -44,6 +44,7 @@
#include <mach/gpmc.h>
#include <mach/hardware.h>
#include <mach/nand.h>
+#include <mach/mux.h>
#include <mach/usb.h>
#include "sdram-micron-mt46h32m32lf-6.h"
@@ -51,6 +52,7 @@
#define OVERO_GPIO_BT_XGATE 15
#define OVERO_GPIO_W2W_NRESET 16
+#define OVERO_GPIO_PENDOWN 114
#define OVERO_GPIO_BT_NRESET 164
#define OVERO_GPIO_USBH_CPEN 168
#define OVERO_GPIO_USBH_NRESET 183
@@ -146,7 +148,7 @@
.name = "smsc911x",
.id = -1,
.num_resources = ARRAY_SIZE(overo_smsc911x_resources),
- .resource = &overo_smsc911x_resources,
+ .resource = overo_smsc911x_resources,
.dev = {
.platform_data = &overo_smsc911x_config,
},
@@ -360,7 +362,8 @@
static void __init overo_init_irq(void)
{
- omap2_init_common_hw(mt46h32m32lf6_sdrc_params);
+ omap2_init_common_hw(mt46h32m32lf6_sdrc_params,
+ mt46h32m32lf6_sdrc_params);
omap_init_irq();
omap_gpio_init();
}
@@ -395,6 +398,10 @@
overo_ads7846_init();
overo_init_smsc911x();
+ /* Ensure SDRC pins are mux'd for self-refresh */
+ omap_cfg_reg(H16_34XX_SDRC_CKE0);
+ omap_cfg_reg(H17_34XX_SDRC_CKE1);
+
if ((gpio_request(OVERO_GPIO_W2W_NRESET,
"OVERO_GPIO_W2W_NRESET") == 0) &&
(gpio_direction_output(OVERO_GPIO_W2W_NRESET, 1) == 0)) {
diff --git a/arch/arm/mach-omap2/board-rx51-peripherals.c b/arch/arm/mach-omap2/board-rx51-peripherals.c
index 9a0bf67..56d931a 100644
--- a/arch/arm/mach-omap2/board-rx51-peripherals.c
+++ b/arch/arm/mach-omap2/board-rx51-peripherals.c
@@ -278,6 +278,10 @@
.setup = rx51_twlgpio_setup,
};
+static struct twl4030_usb_data rx51_usb_data = {
+ .usb_mode = T2_USB_MODE_ULPI,
+};
+
static struct twl4030_platform_data rx51_twldata = {
.irq_base = TWL4030_IRQ_BASE,
.irq_end = TWL4030_IRQ_END,
@@ -286,6 +290,7 @@
.gpio = &rx51_gpio_data,
.keypad = &rx51_kp_data,
.madc = &rx51_madc_data,
+ .usb = &rx51_usb_data,
.vaux1 = &rx51_vaux1,
.vaux2 = &rx51_vaux2,
diff --git a/arch/arm/mach-omap2/board-rx51.c b/arch/arm/mach-omap2/board-rx51.c
index 374ff63..1c9e07f 100644
--- a/arch/arm/mach-omap2/board-rx51.c
+++ b/arch/arm/mach-omap2/board-rx51.c
@@ -61,7 +61,7 @@
static void __init rx51_init_irq(void)
{
- omap2_init_common_hw(NULL);
+ omap2_init_common_hw(NULL, NULL);
omap_init_irq();
omap_gpio_init();
}
@@ -75,6 +75,10 @@
omap_serial_init();
usb_musb_init();
rx51_peripherals_init();
+
+ /* Ensure SDRC pins are mux'd for self-refresh */
+ omap_cfg_reg(H16_34XX_SDRC_CKE0);
+ omap_cfg_reg(H17_34XX_SDRC_CKE1);
}
static void __init rx51_map_io(void)
diff --git a/arch/arm/mach-omap2/board-zoom2.c b/arch/arm/mach-omap2/board-zoom2.c
index bcc0f76..427b7b8 100644
--- a/arch/arm/mach-omap2/board-zoom2.c
+++ b/arch/arm/mach-omap2/board-zoom2.c
@@ -25,7 +25,7 @@
static void __init omap_zoom2_init_irq(void)
{
- omap2_init_common_hw(NULL);
+ omap2_init_common_hw(NULL, NULL);
omap_init_irq();
omap_gpio_init();
}
diff --git a/arch/arm/mach-omap2/clock.c b/arch/arm/mach-omap2/clock.c
index b0665f1..456e2ad 100644
--- a/arch/arm/mach-omap2/clock.c
+++ b/arch/arm/mach-omap2/clock.c
@@ -27,6 +27,7 @@
#include <mach/clock.h>
#include <mach/clockdomain.h>
#include <mach/cpu.h>
+#include <mach/prcm.h>
#include <asm/div64.h>
#include <mach/sdrc.h>
@@ -38,8 +39,6 @@
#include "cm-regbits-24xx.h"
#include "cm-regbits-34xx.h"
-#define MAX_CLOCK_ENABLE_WAIT 100000
-
/* DPLL rate rounding: minimum DPLL multiplier, divider values */
#define DPLL_MIN_MULTIPLIER 1
#define DPLL_MIN_DIVIDER 1
@@ -274,83 +273,97 @@
}
/**
- * omap2_wait_clock_ready - wait for clock to enable
- * @reg: physical address of clock IDLEST register
- * @mask: value to mask against to determine if the clock is active
- * @name: name of the clock (for printk)
+ * omap2_clk_dflt_find_companion - find companion clock to @clk
+ * @clk: struct clk * to find the companion clock of
+ * @other_reg: void __iomem ** to return the companion clock CM_*CLKEN va in
+ * @other_bit: u8 ** to return the companion clock bit shift in
*
- * Returns 1 if the clock enabled in time, or 0 if it failed to enable
- * in roughly MAX_CLOCK_ENABLE_WAIT microseconds.
- */
-int omap2_wait_clock_ready(void __iomem *reg, u32 mask, const char *name)
-{
- int i = 0;
- int ena = 0;
-
- /*
- * 24xx uses 0 to indicate not ready, and 1 to indicate ready.
- * 34xx reverses this, just to keep us on our toes
- */
- if (cpu_mask & (RATE_IN_242X | RATE_IN_243X))
- ena = mask;
- else if (cpu_mask & RATE_IN_343X)
- ena = 0;
-
- /* Wait for lock */
- while (((__raw_readl(reg) & mask) != ena) &&
- (i++ < MAX_CLOCK_ENABLE_WAIT)) {
- udelay(1);
- }
-
- if (i <= MAX_CLOCK_ENABLE_WAIT)
- pr_debug("Clock %s stable after %d loops\n", name, i);
- else
- printk(KERN_ERR "Clock %s didn't enable in %d tries\n",
- name, MAX_CLOCK_ENABLE_WAIT);
-
-
- return (i < MAX_CLOCK_ENABLE_WAIT) ? 1 : 0;
-};
-
-
-/*
- * Note: We don't need special code here for INVERT_ENABLE
- * for the time being since INVERT_ENABLE only applies to clocks enabled by
+ * Note: We don't need special code here for INVERT_ENABLE for the
+ * time being since INVERT_ENABLE only applies to clocks enabled by
* CM_CLKEN_PLL
+ *
+ * Convert CM_ICLKEN* <-> CM_FCLKEN*. This conversion assumes it's
+ * just a matter of XORing the bits.
+ *
+ * Some clocks don't have companion clocks. For example, modules with
+ * only an interface clock (such as MAILBOXES) don't have a companion
+ * clock. Right now, this code relies on the hardware exporting a bit
+ * in the correct companion register that indicates that the
+ * nonexistent 'companion clock' is active. Future patches will
+ * associate this type of code with per-module data structures to
+ * avoid this issue, and remove the casts. No return value.
*/
-static void omap2_clk_wait_ready(struct clk *clk)
+void omap2_clk_dflt_find_companion(struct clk *clk, void __iomem **other_reg,
+ u8 *other_bit)
{
- void __iomem *reg, *other_reg, *st_reg;
- u32 bit;
-
- /*
- * REVISIT: This code is pretty ugly. It would be nice to generalize
- * it and pull it into struct clk itself somehow.
- */
- reg = clk->enable_reg;
+ u32 r;
/*
* Convert CM_ICLKEN* <-> CM_FCLKEN*. This conversion assumes
* it's just a matter of XORing the bits.
*/
- other_reg = (void __iomem *)((u32)reg ^ (CM_FCLKEN ^ CM_ICLKEN));
+ r = ((__force u32)clk->enable_reg ^ (CM_FCLKEN ^ CM_ICLKEN));
- /* Check if both functional and interface clocks
- * are running. */
- bit = 1 << clk->enable_bit;
- if (!(__raw_readl(other_reg) & bit))
- return;
- st_reg = (void __iomem *)(((u32)other_reg & ~0xf0) | 0x20); /* CM_IDLEST* */
-
- omap2_wait_clock_ready(st_reg, bit, clk->name);
+ *other_reg = (__force void __iomem *)r;
+ *other_bit = clk->enable_bit;
}
-static int omap2_dflt_clk_enable(struct clk *clk)
+/**
+ * omap2_clk_dflt_find_idlest - find CM_IDLEST reg va, bit shift for @clk
+ * @clk: struct clk * to find IDLEST info for
+ * @idlest_reg: void __iomem ** to return the CM_IDLEST va in
+ * @idlest_bit: u8 ** to return the CM_IDLEST bit shift in
+ *
+ * Return the CM_IDLEST register address and bit shift corresponding
+ * to the module that "owns" this clock. This default code assumes
+ * that the CM_IDLEST bit shift is the CM_*CLKEN bit shift, and that
+ * the IDLEST register address ID corresponds to the CM_*CLKEN
+ * register address ID (e.g., that CM_FCLKEN2 corresponds to
+ * CM_IDLEST2). This is not true for all modules. No return value.
+ */
+void omap2_clk_dflt_find_idlest(struct clk *clk, void __iomem **idlest_reg,
+ u8 *idlest_bit)
+{
+ u32 r;
+
+ r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20);
+ *idlest_reg = (__force void __iomem *)r;
+ *idlest_bit = clk->enable_bit;
+}
+
+/**
+ * omap2_module_wait_ready - wait for an OMAP module to leave IDLE
+ * @clk: struct clk * belonging to the module
+ *
+ * If the necessary clocks for the OMAP hardware IP block that
+ * corresponds to clock @clk are enabled, then wait for the module to
+ * indicate readiness (i.e., to leave IDLE). This code does not
+ * belong in the clock code and will be moved in the medium term to
+ * module-dependent code. No return value.
+ */
+static void omap2_module_wait_ready(struct clk *clk)
+{
+ void __iomem *companion_reg, *idlest_reg;
+ u8 other_bit, idlest_bit;
+
+ /* Not all modules have multiple clocks that their IDLEST depends on */
+ if (clk->ops->find_companion) {
+ clk->ops->find_companion(clk, &companion_reg, &other_bit);
+ if (!(__raw_readl(companion_reg) & (1 << other_bit)))
+ return;
+ }
+
+ clk->ops->find_idlest(clk, &idlest_reg, &idlest_bit);
+
+ omap2_cm_wait_idlest(idlest_reg, (1 << idlest_bit), clk->name);
+}
+
+int omap2_dflt_clk_enable(struct clk *clk)
{
u32 v;
if (unlikely(clk->enable_reg == NULL)) {
- printk(KERN_ERR "clock.c: Enable for %s without enable code\n",
+ pr_err("clock.c: Enable for %s without enable code\n",
clk->name);
return 0; /* REVISIT: -EINVAL */
}
@@ -363,26 +376,13 @@
__raw_writel(v, clk->enable_reg);
v = __raw_readl(clk->enable_reg); /* OCP barrier */
+ if (clk->ops->find_idlest)
+ omap2_module_wait_ready(clk);
+
return 0;
}
-static int omap2_dflt_clk_enable_wait(struct clk *clk)
-{
- int ret;
-
- if (!clk->enable_reg) {
- printk(KERN_ERR "clock.c: Enable for %s without enable code\n",
- clk->name);
- return 0; /* REVISIT: -EINVAL */
- }
-
- ret = omap2_dflt_clk_enable(clk);
- if (ret == 0)
- omap2_clk_wait_ready(clk);
- return ret;
-}
-
-static void omap2_dflt_clk_disable(struct clk *clk)
+void omap2_dflt_clk_disable(struct clk *clk)
{
u32 v;
@@ -406,8 +406,10 @@
}
const struct clkops clkops_omap2_dflt_wait = {
- .enable = omap2_dflt_clk_enable_wait,
+ .enable = omap2_dflt_clk_enable,
.disable = omap2_dflt_clk_disable,
+ .find_companion = omap2_clk_dflt_find_companion,
+ .find_idlest = omap2_clk_dflt_find_idlest,
};
const struct clkops clkops_omap2_dflt = {
diff --git a/arch/arm/mach-omap2/clock.h b/arch/arm/mach-omap2/clock.h
index 2679ddf..9ae7540 100644
--- a/arch/arm/mach-omap2/clock.h
+++ b/arch/arm/mach-omap2/clock.h
@@ -65,6 +65,12 @@
u32 omap2_get_dpll_rate(struct clk *clk);
int omap2_wait_clock_ready(void __iomem *reg, u32 cval, const char *name);
void omap2_clk_prepare_for_reboot(void);
+int omap2_dflt_clk_enable(struct clk *clk);
+void omap2_dflt_clk_disable(struct clk *clk);
+void omap2_clk_dflt_find_companion(struct clk *clk, void __iomem **other_reg,
+ u8 *other_bit);
+void omap2_clk_dflt_find_idlest(struct clk *clk, void __iomem **idlest_reg,
+ u8 *idlest_bit);
extern const struct clkops clkops_omap2_dflt_wait;
extern const struct clkops clkops_omap2_dflt;
diff --git a/arch/arm/mach-omap2/clock24xx.c b/arch/arm/mach-omap2/clock24xx.c
index 44de027..bc5d3ac 100644
--- a/arch/arm/mach-omap2/clock24xx.c
+++ b/arch/arm/mach-omap2/clock24xx.c
@@ -30,6 +30,7 @@
#include <mach/clock.h>
#include <mach/sram.h>
+#include <mach/prcm.h>
#include <asm/div64.h>
#include <asm/clkdev.h>
@@ -43,6 +44,18 @@
static const struct clkops clkops_oscck;
static const struct clkops clkops_fixed;
+static void omap2430_clk_i2chs_find_idlest(struct clk *clk,
+ void __iomem **idlest_reg,
+ u8 *idlest_bit);
+
+/* 2430 I2CHS has non-standard IDLEST register */
+static const struct clkops clkops_omap2430_i2chs_wait = {
+ .enable = omap2_dflt_clk_enable,
+ .disable = omap2_dflt_clk_disable,
+ .find_idlest = omap2430_clk_i2chs_find_idlest,
+ .find_companion = omap2_clk_dflt_find_companion,
+};
+
#include "clock24xx.h"
struct omap_clk {
@@ -240,6 +253,26 @@
*-------------------------------------------------------------------------*/
/**
+ * omap2430_clk_i2chs_find_idlest - return CM_IDLEST info for 2430 I2CHS
+ * @clk: struct clk * being enabled
+ * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into
+ * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into
+ *
+ * OMAP2430 I2CHS CM_IDLEST bits are in CM_IDLEST1_CORE, but the
+ * CM_*CLKEN bits are in CM_{I,F}CLKEN2_CORE. This custom function
+ * passes back the correct CM_IDLEST register address for I2CHS
+ * modules. No return value.
+ */
+static void omap2430_clk_i2chs_find_idlest(struct clk *clk,
+ void __iomem **idlest_reg,
+ u8 *idlest_bit)
+{
+ *idlest_reg = OMAP_CM_REGADDR(CORE_MOD, CM_IDLEST);
+ *idlest_bit = clk->enable_bit;
+}
+
+
+/**
* omap2xxx_clk_get_core_rate - return the CORE_CLK rate
* @clk: pointer to the combined dpll_ck + core_ck (currently "dpll_ck")
*
@@ -325,8 +358,8 @@
else if (clk == &apll54_ck)
cval = OMAP24XX_ST_54M_APLL;
- omap2_wait_clock_ready(OMAP_CM_REGADDR(PLL_MOD, CM_IDLEST), cval,
- clk->name);
+ omap2_cm_wait_idlest(OMAP_CM_REGADDR(PLL_MOD, CM_IDLEST), cval,
+ clk->name);
/*
* REVISIT: Should we return an error code if omap2_wait_clock_ready()
diff --git a/arch/arm/mach-omap2/clock24xx.h b/arch/arm/mach-omap2/clock24xx.h
index 458f00c..d19cf7a 100644
--- a/arch/arm/mach-omap2/clock24xx.h
+++ b/arch/arm/mach-omap2/clock24xx.h
@@ -2337,7 +2337,7 @@
static struct clk i2chs2_fck = {
.name = "i2c_fck",
- .ops = &clkops_omap2_dflt_wait,
+ .ops = &clkops_omap2430_i2chs_wait,
.id = 2,
.parent = &func_96m_ck,
.clkdm_name = "core_l4_clkdm",
@@ -2370,7 +2370,7 @@
static struct clk i2chs1_fck = {
.name = "i2c_fck",
- .ops = &clkops_omap2_dflt_wait,
+ .ops = &clkops_omap2430_i2chs_wait,
.id = 1,
.parent = &func_96m_ck,
.clkdm_name = "core_l4_clkdm",
diff --git a/arch/arm/mach-omap2/clock34xx.c b/arch/arm/mach-omap2/clock34xx.c
index 045da92..cd7819c 100644
--- a/arch/arm/mach-omap2/clock34xx.c
+++ b/arch/arm/mach-omap2/clock34xx.c
@@ -2,7 +2,7 @@
* OMAP3-specific clock framework functions
*
* Copyright (C) 2007-2008 Texas Instruments, Inc.
- * Copyright (C) 2007-2008 Nokia Corporation
+ * Copyright (C) 2007-2009 Nokia Corporation
*
* Written by Paul Walmsley
* Testing and integration fixes by Jouni Högander
@@ -41,6 +41,37 @@
static const struct clkops clkops_noncore_dpll_ops;
+static void omap3430es2_clk_ssi_find_idlest(struct clk *clk,
+ void __iomem **idlest_reg,
+ u8 *idlest_bit);
+static void omap3430es2_clk_hsotgusb_find_idlest(struct clk *clk,
+ void __iomem **idlest_reg,
+ u8 *idlest_bit);
+static void omap3430es2_clk_dss_usbhost_find_idlest(struct clk *clk,
+ void __iomem **idlest_reg,
+ u8 *idlest_bit);
+
+static const struct clkops clkops_omap3430es2_ssi_wait = {
+ .enable = omap2_dflt_clk_enable,
+ .disable = omap2_dflt_clk_disable,
+ .find_idlest = omap3430es2_clk_ssi_find_idlest,
+ .find_companion = omap2_clk_dflt_find_companion,
+};
+
+static const struct clkops clkops_omap3430es2_hsotgusb_wait = {
+ .enable = omap2_dflt_clk_enable,
+ .disable = omap2_dflt_clk_disable,
+ .find_idlest = omap3430es2_clk_hsotgusb_find_idlest,
+ .find_companion = omap2_clk_dflt_find_companion,
+};
+
+static const struct clkops clkops_omap3430es2_dss_usbhost_wait = {
+ .enable = omap2_dflt_clk_enable,
+ .disable = omap2_dflt_clk_disable,
+ .find_idlest = omap3430es2_clk_dss_usbhost_find_idlest,
+ .find_companion = omap2_clk_dflt_find_companion,
+};
+
#include "clock34xx.h"
struct omap_clk {
@@ -157,10 +188,13 @@
CLK(NULL, "fshostusb_fck", &fshostusb_fck, CK_3430ES1),
CLK(NULL, "core_12m_fck", &core_12m_fck, CK_343X),
CLK("omap_hdq.0", "fck", &hdq_fck, CK_343X),
- CLK(NULL, "ssi_ssr_fck", &ssi_ssr_fck, CK_343X),
- CLK(NULL, "ssi_sst_fck", &ssi_sst_fck, CK_343X),
+ CLK(NULL, "ssi_ssr_fck", &ssi_ssr_fck_3430es1, CK_3430ES1),
+ CLK(NULL, "ssi_ssr_fck", &ssi_ssr_fck_3430es2, CK_3430ES2),
+ CLK(NULL, "ssi_sst_fck", &ssi_sst_fck_3430es1, CK_3430ES1),
+ CLK(NULL, "ssi_sst_fck", &ssi_sst_fck_3430es2, CK_3430ES2),
CLK(NULL, "core_l3_ick", &core_l3_ick, CK_343X),
- CLK("musb_hdrc", "ick", &hsotgusb_ick, CK_343X),
+ CLK("musb_hdrc", "ick", &hsotgusb_ick_3430es1, CK_3430ES1),
+ CLK("musb_hdrc", "ick", &hsotgusb_ick_3430es2, CK_3430ES2),
CLK(NULL, "sdrc_ick", &sdrc_ick, CK_343X),
CLK(NULL, "gpmc_fck", &gpmc_fck, CK_343X),
CLK(NULL, "security_l3_ick", &security_l3_ick, CK_343X),
@@ -193,18 +227,21 @@
CLK(NULL, "mailboxes_ick", &mailboxes_ick, CK_343X),
CLK(NULL, "omapctrl_ick", &omapctrl_ick, CK_343X),
CLK(NULL, "ssi_l4_ick", &ssi_l4_ick, CK_343X),
- CLK(NULL, "ssi_ick", &ssi_ick, CK_343X),
+ CLK(NULL, "ssi_ick", &ssi_ick_3430es1, CK_3430ES1),
+ CLK(NULL, "ssi_ick", &ssi_ick_3430es2, CK_3430ES2),
CLK(NULL, "usb_l4_ick", &usb_l4_ick, CK_3430ES1),
CLK(NULL, "security_l4_ick2", &security_l4_ick2, CK_343X),
CLK(NULL, "aes1_ick", &aes1_ick, CK_343X),
CLK("omap_rng", "ick", &rng_ick, CK_343X),
CLK(NULL, "sha11_ick", &sha11_ick, CK_343X),
CLK(NULL, "des1_ick", &des1_ick, CK_343X),
- CLK("omapfb", "dss1_fck", &dss1_alwon_fck, CK_343X),
+ CLK("omapfb", "dss1_fck", &dss1_alwon_fck_3430es1, CK_3430ES1),
+ CLK("omapfb", "dss1_fck", &dss1_alwon_fck_3430es2, CK_3430ES2),
CLK("omapfb", "tv_fck", &dss_tv_fck, CK_343X),
CLK("omapfb", "video_fck", &dss_96m_fck, CK_343X),
CLK("omapfb", "dss2_fck", &dss2_alwon_fck, CK_343X),
- CLK("omapfb", "ick", &dss_ick, CK_343X),
+ CLK("omapfb", "ick", &dss_ick_3430es1, CK_3430ES1),
+ CLK("omapfb", "ick", &dss_ick_3430es2, CK_3430ES2),
CLK(NULL, "cam_mclk", &cam_mclk, CK_343X),
CLK(NULL, "cam_ick", &cam_ick, CK_343X),
CLK(NULL, "csi2_96m_fck", &csi2_96m_fck, CK_343X),
@@ -301,6 +338,73 @@
#define SDRC_MPURATE_LOOPS 96
/**
+ * omap3430es2_clk_ssi_find_idlest - return CM_IDLEST info for SSI
+ * @clk: struct clk * being enabled
+ * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into
+ * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into
+ *
+ * The OMAP3430ES2 SSI target CM_IDLEST bit is at a different shift
+ * from the CM_{I,F}CLKEN bit. Pass back the correct info via
+ * @idlest_reg and @idlest_bit. No return value.
+ */
+static void omap3430es2_clk_ssi_find_idlest(struct clk *clk,
+ void __iomem **idlest_reg,
+ u8 *idlest_bit)
+{
+ u32 r;
+
+ r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20);
+ *idlest_reg = (__force void __iomem *)r;
+ *idlest_bit = OMAP3430ES2_ST_SSI_IDLE_SHIFT;
+}
+
+/**
+ * omap3430es2_clk_dss_usbhost_find_idlest - CM_IDLEST info for DSS, USBHOST
+ * @clk: struct clk * being enabled
+ * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into
+ * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into
+ *
+ * Some OMAP modules on OMAP3 ES2+ chips have both initiator and
+ * target IDLEST bits. For our purposes, we are concerned with the
+ * target IDLEST bits, which exist at a different bit position than
+ * the *CLKEN bit position for these modules (DSS and USBHOST) (The
+ * default find_idlest code assumes that they are at the same
+ * position.) No return value.
+ */
+static void omap3430es2_clk_dss_usbhost_find_idlest(struct clk *clk,
+ void __iomem **idlest_reg,
+ u8 *idlest_bit)
+{
+ u32 r;
+
+ r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20);
+ *idlest_reg = (__force void __iomem *)r;
+ /* USBHOST_IDLE has same shift */
+ *idlest_bit = OMAP3430ES2_ST_DSS_IDLE_SHIFT;
+}
+
+/**
+ * omap3430es2_clk_hsotgusb_find_idlest - return CM_IDLEST info for HSOTGUSB
+ * @clk: struct clk * being enabled
+ * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into
+ * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into
+ *
+ * The OMAP3430ES2 HSOTGUSB target CM_IDLEST bit is at a different
+ * shift from the CM_{I,F}CLKEN bit. Pass back the correct info via
+ * @idlest_reg and @idlest_bit. No return value.
+ */
+static void omap3430es2_clk_hsotgusb_find_idlest(struct clk *clk,
+ void __iomem **idlest_reg,
+ u8 *idlest_bit)
+{
+ u32 r;
+
+ r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20);
+ *idlest_reg = (__force void __iomem *)r;
+ *idlest_bit = OMAP3430ES2_ST_HSOTGUSB_IDLE_SHIFT;
+}
+
+/**
* omap3_dpll_recalc - recalculate DPLL rate
* @clk: DPLL struct clk
*
@@ -725,7 +829,9 @@
u32 unlock_dll = 0;
u32 c;
unsigned long validrate, sdrcrate, mpurate;
- struct omap_sdrc_params *sp;
+ struct omap_sdrc_params *sdrc_cs0;
+ struct omap_sdrc_params *sdrc_cs1;
+ int ret;
if (!clk || !rate)
return -EINVAL;
@@ -743,8 +849,8 @@
else
sdrcrate >>= ((clk->rate / rate) >> 1);
- sp = omap2_sdrc_get_params(sdrcrate);
- if (!sp)
+ ret = omap2_sdrc_get_params(sdrcrate, &sdrc_cs0, &sdrc_cs1);
+ if (ret)
return -EINVAL;
if (sdrcrate < MIN_SDRC_DLL_LOCK_FREQ) {
@@ -765,12 +871,29 @@
pr_debug("clock: changing CORE DPLL rate from %lu to %lu\n", clk->rate,
validrate);
- pr_debug("clock: SDRC timing params used: %08x %08x %08x\n",
- sp->rfr_ctrl, sp->actim_ctrla, sp->actim_ctrlb);
+ pr_debug("clock: SDRC CS0 timing params used:"
+ " RFR %08x CTRLA %08x CTRLB %08x MR %08x\n",
+ sdrc_cs0->rfr_ctrl, sdrc_cs0->actim_ctrla,
+ sdrc_cs0->actim_ctrlb, sdrc_cs0->mr);
+ if (sdrc_cs1)
+ pr_debug("clock: SDRC CS1 timing params used: "
+ " RFR %08x CTRLA %08x CTRLB %08x MR %08x\n",
+ sdrc_cs1->rfr_ctrl, sdrc_cs1->actim_ctrla,
+ sdrc_cs1->actim_ctrlb, sdrc_cs1->mr);
- omap3_configure_core_dpll(sp->rfr_ctrl, sp->actim_ctrla,
- sp->actim_ctrlb, new_div, unlock_dll, c,
- sp->mr, rate > clk->rate);
+ if (sdrc_cs1)
+ omap3_configure_core_dpll(
+ new_div, unlock_dll, c, rate > clk->rate,
+ sdrc_cs0->rfr_ctrl, sdrc_cs0->actim_ctrla,
+ sdrc_cs0->actim_ctrlb, sdrc_cs0->mr,
+ sdrc_cs1->rfr_ctrl, sdrc_cs1->actim_ctrla,
+ sdrc_cs1->actim_ctrlb, sdrc_cs1->mr);
+ else
+ omap3_configure_core_dpll(
+ new_div, unlock_dll, c, rate > clk->rate,
+ sdrc_cs0->rfr_ctrl, sdrc_cs0->actim_ctrla,
+ sdrc_cs0->actim_ctrlb, sdrc_cs0->mr,
+ 0, 0, 0, 0);
return 0;
}
diff --git a/arch/arm/mach-omap2/clock34xx.h b/arch/arm/mach-omap2/clock34xx.h
index e433aec..57cc272 100644
--- a/arch/arm/mach-omap2/clock34xx.h
+++ b/arch/arm/mach-omap2/clock34xx.h
@@ -1568,7 +1568,7 @@
{ .parent = NULL }
};
-static struct clk ssi_ssr_fck = {
+static struct clk ssi_ssr_fck_3430es1 = {
.name = "ssi_ssr_fck",
.ops = &clkops_omap2_dflt,
.init = &omap2_init_clksel_parent,
@@ -1581,10 +1581,31 @@
.recalc = &omap2_clksel_recalc,
};
-static struct clk ssi_sst_fck = {
+static struct clk ssi_ssr_fck_3430es2 = {
+ .name = "ssi_ssr_fck",
+ .ops = &clkops_omap3430es2_ssi_wait,
+ .init = &omap2_init_clksel_parent,
+ .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_FCLKEN1),
+ .enable_bit = OMAP3430_EN_SSI_SHIFT,
+ .clksel_reg = OMAP_CM_REGADDR(CORE_MOD, CM_CLKSEL),
+ .clksel_mask = OMAP3430_CLKSEL_SSI_MASK,
+ .clksel = ssi_ssr_clksel,
+ .clkdm_name = "core_l4_clkdm",
+ .recalc = &omap2_clksel_recalc,
+};
+
+static struct clk ssi_sst_fck_3430es1 = {
.name = "ssi_sst_fck",
.ops = &clkops_null,
- .parent = &ssi_ssr_fck,
+ .parent = &ssi_ssr_fck_3430es1,
+ .fixed_div = 2,
+ .recalc = &omap2_fixed_divisor_recalc,
+};
+
+static struct clk ssi_sst_fck_3430es2 = {
+ .name = "ssi_sst_fck",
+ .ops = &clkops_null,
+ .parent = &ssi_ssr_fck_3430es2,
.fixed_div = 2,
.recalc = &omap2_fixed_divisor_recalc,
};
@@ -1606,9 +1627,19 @@
.recalc = &followparent_recalc,
};
-static struct clk hsotgusb_ick = {
+static struct clk hsotgusb_ick_3430es1 = {
.name = "hsotgusb_ick",
- .ops = &clkops_omap2_dflt_wait,
+ .ops = &clkops_omap2_dflt,
+ .parent = &core_l3_ick,
+ .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN1),
+ .enable_bit = OMAP3430_EN_HSOTGUSB_SHIFT,
+ .clkdm_name = "core_l3_clkdm",
+ .recalc = &followparent_recalc,
+};
+
+static struct clk hsotgusb_ick_3430es2 = {
+ .name = "hsotgusb_ick",
+ .ops = &clkops_omap3430es2_hsotgusb_wait,
.parent = &core_l3_ick,
.enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN1),
.enable_bit = OMAP3430_EN_HSOTGUSB_SHIFT,
@@ -1947,7 +1978,7 @@
.recalc = &followparent_recalc,
};
-static struct clk ssi_ick = {
+static struct clk ssi_ick_3430es1 = {
.name = "ssi_ick",
.ops = &clkops_omap2_dflt,
.parent = &ssi_l4_ick,
@@ -1957,6 +1988,16 @@
.recalc = &followparent_recalc,
};
+static struct clk ssi_ick_3430es2 = {
+ .name = "ssi_ick",
+ .ops = &clkops_omap3430es2_ssi_wait,
+ .parent = &ssi_l4_ick,
+ .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN1),
+ .enable_bit = OMAP3430_EN_SSI_SHIFT,
+ .clkdm_name = "core_l4_clkdm",
+ .recalc = &followparent_recalc,
+};
+
/* REVISIT: Technically the TRM claims that this is CORE_CLK based,
* but l4_ick makes more sense to me */
@@ -2024,7 +2065,7 @@
};
/* DSS */
-static struct clk dss1_alwon_fck = {
+static struct clk dss1_alwon_fck_3430es1 = {
.name = "dss1_alwon_fck",
.ops = &clkops_omap2_dflt,
.parent = &dpll4_m4x2_ck,
@@ -2034,6 +2075,16 @@
.recalc = &followparent_recalc,
};
+static struct clk dss1_alwon_fck_3430es2 = {
+ .name = "dss1_alwon_fck",
+ .ops = &clkops_omap3430es2_dss_usbhost_wait,
+ .parent = &dpll4_m4x2_ck,
+ .enable_reg = OMAP_CM_REGADDR(OMAP3430_DSS_MOD, CM_FCLKEN),
+ .enable_bit = OMAP3430_EN_DSS1_SHIFT,
+ .clkdm_name = "dss_clkdm",
+ .recalc = &followparent_recalc,
+};
+
static struct clk dss_tv_fck = {
.name = "dss_tv_fck",
.ops = &clkops_omap2_dflt,
@@ -2067,7 +2118,7 @@
.recalc = &followparent_recalc,
};
-static struct clk dss_ick = {
+static struct clk dss_ick_3430es1 = {
/* Handles both L3 and L4 clocks */
.name = "dss_ick",
.ops = &clkops_omap2_dflt,
@@ -2079,6 +2130,18 @@
.recalc = &followparent_recalc,
};
+static struct clk dss_ick_3430es2 = {
+ /* Handles both L3 and L4 clocks */
+ .name = "dss_ick",
+ .ops = &clkops_omap3430es2_dss_usbhost_wait,
+ .parent = &l4_ick,
+ .init = &omap2_init_clk_clkdm,
+ .enable_reg = OMAP_CM_REGADDR(OMAP3430_DSS_MOD, CM_ICLKEN),
+ .enable_bit = OMAP3430_CM_ICLKEN_DSS_EN_DSS_SHIFT,
+ .clkdm_name = "dss_clkdm",
+ .recalc = &followparent_recalc,
+};
+
/* CAM */
static struct clk cam_mclk = {
@@ -2118,7 +2181,7 @@
static struct clk usbhost_120m_fck = {
.name = "usbhost_120m_fck",
- .ops = &clkops_omap2_dflt_wait,
+ .ops = &clkops_omap2_dflt,
.parent = &dpll5_m2_ck,
.init = &omap2_init_clk_clkdm,
.enable_reg = OMAP_CM_REGADDR(OMAP3430ES2_USBHOST_MOD, CM_FCLKEN),
@@ -2129,7 +2192,7 @@
static struct clk usbhost_48m_fck = {
.name = "usbhost_48m_fck",
- .ops = &clkops_omap2_dflt_wait,
+ .ops = &clkops_omap3430es2_dss_usbhost_wait,
.parent = &omap_48m_fck,
.init = &omap2_init_clk_clkdm,
.enable_reg = OMAP_CM_REGADDR(OMAP3430ES2_USBHOST_MOD, CM_FCLKEN),
@@ -2141,7 +2204,7 @@
static struct clk usbhost_ick = {
/* Handles both L3 and L4 clocks */
.name = "usbhost_ick",
- .ops = &clkops_omap2_dflt_wait,
+ .ops = &clkops_omap3430es2_dss_usbhost_wait,
.parent = &l4_ick,
.init = &omap2_init_clk_clkdm,
.enable_reg = OMAP_CM_REGADDR(OMAP3430ES2_USBHOST_MOD, CM_ICLKEN),
diff --git a/arch/arm/mach-omap2/cm.h b/arch/arm/mach-omap2/cm.h
index 1d3c93b..f3c91a1 100644
--- a/arch/arm/mach-omap2/cm.h
+++ b/arch/arm/mach-omap2/cm.h
@@ -29,9 +29,9 @@
* These registers appear once per CM module.
*/
-#define OMAP3430_CM_REVISION OMAP_CM_REGADDR(OCP_MOD, 0x0000)
-#define OMAP3430_CM_SYSCONFIG OMAP_CM_REGADDR(OCP_MOD, 0x0010)
-#define OMAP3430_CM_POLCTRL OMAP_CM_REGADDR(OCP_MOD, 0x009c)
+#define OMAP3430_CM_REVISION OMAP34XX_CM_REGADDR(OCP_MOD, 0x0000)
+#define OMAP3430_CM_SYSCONFIG OMAP34XX_CM_REGADDR(OCP_MOD, 0x0010)
+#define OMAP3430_CM_POLCTRL OMAP34XX_CM_REGADDR(OCP_MOD, 0x009c)
#define OMAP3_CM_CLKOUT_CTRL_OFFSET 0x0070
#define OMAP3430_CM_CLKOUT_CTRL OMAP_CM_REGADDR(OMAP3430_CCR_MOD, 0x0070)
diff --git a/arch/arm/mach-omap2/io.c b/arch/arm/mach-omap2/io.c
index 3a86b0f..e9b9bcb 100644
--- a/arch/arm/mach-omap2/io.c
+++ b/arch/arm/mach-omap2/io.c
@@ -276,14 +276,15 @@
return v;
}
-void __init omap2_init_common_hw(struct omap_sdrc_params *sp)
+void __init omap2_init_common_hw(struct omap_sdrc_params *sdrc_cs0,
+ struct omap_sdrc_params *sdrc_cs1)
{
omap2_mux_init();
#ifndef CONFIG_ARCH_OMAP4 /* FIXME: Remove this once the clkdev is ready */
pwrdm_init(powerdomains_omap);
clkdm_init(clockdomains_omap, clkdm_pwrdm_autodeps);
omap2_clk_init();
- omap2_sdrc_init(sp);
+ omap2_sdrc_init(sdrc_cs0, sdrc_cs1);
_omap2_init_reprogram_sdrc();
#endif
gpmc_init();
diff --git a/arch/arm/mach-omap2/mmc-twl4030.c b/arch/arm/mach-omap2/mmc-twl4030.c
index 1541fd4..3c04c2f 100644
--- a/arch/arm/mach-omap2/mmc-twl4030.c
+++ b/arch/arm/mach-omap2/mmc-twl4030.c
@@ -119,6 +119,7 @@
if (i != 0)
break;
ret = PTR_ERR(reg);
+ hsmmc[i].vcc = NULL;
goto err;
}
hsmmc[i].vcc = reg;
@@ -165,8 +166,13 @@
static void twl_mmc_cleanup(struct device *dev)
{
struct omap_mmc_platform_data *mmc = dev->platform_data;
+ int i;
gpio_free(mmc->slots[0].switch_pin);
+ for(i = 0; i < ARRAY_SIZE(hsmmc); i++) {
+ regulator_put(hsmmc[i].vcc);
+ regulator_put(hsmmc[i].vcc_aux);
+ }
}
#ifdef CONFIG_PM
diff --git a/arch/arm/mach-omap2/mux.c b/arch/arm/mach-omap2/mux.c
index 026c4fc..43d6b92 100644
--- a/arch/arm/mach-omap2/mux.c
+++ b/arch/arm/mach-omap2/mux.c
@@ -486,6 +486,12 @@
OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT)
MUX_CFG_34XX("J25_34XX_GPIO170", 0x1c6,
OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT)
+
+/* OMAP3 SDRC CKE signals to SDR/DDR ram chips */
+MUX_CFG_34XX("H16_34XX_SDRC_CKE0", 0x262,
+ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
+MUX_CFG_34XX("H17_34XX_SDRC_CKE1", 0x264,
+ OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
};
#define OMAP34XX_PINS_SZ ARRAY_SIZE(omap34xx_pins)
diff --git a/arch/arm/mach-omap2/pm.h b/arch/arm/mach-omap2/pm.h
index f7b3baf..21201cd 100644
--- a/arch/arm/mach-omap2/pm.h
+++ b/arch/arm/mach-omap2/pm.h
@@ -11,9 +11,6 @@
#ifndef __ARCH_ARM_MACH_OMAP2_PM_H
#define __ARCH_ARM_MACH_OMAP2_PM_H
-extern int omap2_pm_init(void);
-extern int omap3_pm_init(void);
-
#ifdef CONFIG_PM_DEBUG
extern void omap2_pm_dump(int mode, int resume, unsigned int us);
extern int omap2_pm_debug;
diff --git a/arch/arm/mach-omap2/pm24xx.c b/arch/arm/mach-omap2/pm24xx.c
index db10255..528dbdc 100644
--- a/arch/arm/mach-omap2/pm24xx.c
+++ b/arch/arm/mach-omap2/pm24xx.c
@@ -470,7 +470,7 @@
WKUP_MOD, PM_WKEN);
}
-int __init omap2_pm_init(void)
+static int __init omap2_pm_init(void)
{
u32 l;
diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c
index 841d4c5..488d595 100644
--- a/arch/arm/mach-omap2/pm34xx.c
+++ b/arch/arm/mach-omap2/pm34xx.c
@@ -39,7 +39,9 @@
struct power_state {
struct powerdomain *pwrdm;
u32 next_state;
+#ifdef CONFIG_SUSPEND
u32 saved_state;
+#endif
struct list_head node;
};
@@ -293,6 +295,9 @@
local_irq_enable();
}
+#ifdef CONFIG_SUSPEND
+static suspend_state_t suspend_state;
+
static int omap3_pm_prepare(void)
{
disable_hlt();
@@ -321,7 +326,6 @@
restore:
/* Restore next_pwrsts */
list_for_each_entry(pwrst, &pwrst_list, node) {
- set_pwrdm_state(pwrst->pwrdm, pwrst->saved_state);
state = pwrdm_read_prev_pwrst(pwrst->pwrdm);
if (state > pwrst->next_state) {
printk(KERN_INFO "Powerdomain (%s) didn't enter "
@@ -329,6 +333,7 @@
pwrst->pwrdm->name, pwrst->next_state);
ret = -1;
}
+ set_pwrdm_state(pwrst->pwrdm, pwrst->saved_state);
}
if (ret)
printk(KERN_ERR "Could not enter target state in pm_suspend\n");
@@ -339,11 +344,11 @@
return ret;
}
-static int omap3_pm_enter(suspend_state_t state)
+static int omap3_pm_enter(suspend_state_t unused)
{
int ret = 0;
- switch (state) {
+ switch (suspend_state) {
case PM_SUSPEND_STANDBY:
case PM_SUSPEND_MEM:
ret = omap3_pm_suspend();
@@ -360,12 +365,30 @@
enable_hlt();
}
+/* Hooks to enable / disable UART interrupts during suspend */
+static int omap3_pm_begin(suspend_state_t state)
+{
+ suspend_state = state;
+ omap_uart_enable_irqs(0);
+ return 0;
+}
+
+static void omap3_pm_end(void)
+{
+ suspend_state = PM_SUSPEND_ON;
+ omap_uart_enable_irqs(1);
+ return;
+}
+
static struct platform_suspend_ops omap_pm_ops = {
+ .begin = omap3_pm_begin,
+ .end = omap3_pm_end,
.prepare = omap3_pm_prepare,
.enter = omap3_pm_enter,
.finish = omap3_pm_finish,
.valid = suspend_valid_only_mem,
};
+#endif /* CONFIG_SUSPEND */
/**
@@ -613,6 +636,24 @@
/* Clear any pending PRCM interrupts */
prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
+ /* Don't attach IVA interrupts */
+ prm_write_mod_reg(0, WKUP_MOD, OMAP3430_PM_IVAGRPSEL);
+ prm_write_mod_reg(0, CORE_MOD, OMAP3430_PM_IVAGRPSEL1);
+ prm_write_mod_reg(0, CORE_MOD, OMAP3430ES2_PM_IVAGRPSEL3);
+ prm_write_mod_reg(0, OMAP3430_PER_MOD, OMAP3430_PM_IVAGRPSEL);
+
+ /* Clear any pending 'reset' flags */
+ prm_write_mod_reg(0xffffffff, MPU_MOD, RM_RSTST);
+ prm_write_mod_reg(0xffffffff, CORE_MOD, RM_RSTST);
+ prm_write_mod_reg(0xffffffff, OMAP3430_PER_MOD, RM_RSTST);
+ prm_write_mod_reg(0xffffffff, OMAP3430_EMU_MOD, RM_RSTST);
+ prm_write_mod_reg(0xffffffff, OMAP3430_NEON_MOD, RM_RSTST);
+ prm_write_mod_reg(0xffffffff, OMAP3430_DSS_MOD, RM_RSTST);
+ prm_write_mod_reg(0xffffffff, OMAP3430ES2_USBHOST_MOD, RM_RSTST);
+
+ /* Clear any pending PRCM interrupts */
+ prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
+
omap3_iva_idle();
omap3_d2d_idle();
}
@@ -652,7 +693,7 @@
return 0;
}
-int __init omap3_pm_init(void)
+static int __init omap3_pm_init(void)
{
struct power_state *pwrst, *tmp;
int ret;
@@ -692,7 +733,9 @@
_omap_sram_idle = omap_sram_push(omap34xx_cpu_suspend,
omap34xx_cpu_suspend_sz);
+#ifdef CONFIG_SUSPEND
suspend_set_ops(&omap_pm_ops);
+#endif /* CONFIG_SUSPEND */
pm_idle = omap3_pm_idle;
diff --git a/arch/arm/mach-omap2/prcm.c b/arch/arm/mach-omap2/prcm.c
index f945156..ced555a 100644
--- a/arch/arm/mach-omap2/prcm.c
+++ b/arch/arm/mach-omap2/prcm.c
@@ -17,6 +17,7 @@
#include <linux/init.h>
#include <linux/clk.h>
#include <linux/io.h>
+#include <linux/delay.h>
#include <mach/common.h>
#include <mach/prcm.h>
@@ -28,6 +29,8 @@
static void __iomem *prm_base;
static void __iomem *cm_base;
+#define MAX_MODULE_ENABLE_WAIT 100000
+
u32 omap_prcm_get_reset_sources(void)
{
/* XXX This presumably needs modification for 34XX */
@@ -120,6 +123,46 @@
}
EXPORT_SYMBOL(cm_rmw_mod_reg_bits);
+/**
+ * omap2_cm_wait_idlest - wait for IDLEST bit to indicate module readiness
+ * @reg: physical address of module IDLEST register
+ * @mask: value to mask against to determine if the module is active
+ * @name: name of the clock (for printk)
+ *
+ * Returns 1 if the module indicated readiness in time, or 0 if it
+ * failed to enable in roughly MAX_MODULE_ENABLE_WAIT microseconds.
+ */
+int omap2_cm_wait_idlest(void __iomem *reg, u32 mask, const char *name)
+{
+ int i = 0;
+ int ena = 0;
+
+ /*
+ * 24xx uses 0 to indicate not ready, and 1 to indicate ready.
+ * 34xx reverses this, just to keep us on our toes
+ */
+ if (cpu_is_omap24xx())
+ ena = mask;
+ else if (cpu_is_omap34xx())
+ ena = 0;
+ else
+ BUG();
+
+ /* Wait for lock */
+ while (((__raw_readl(reg) & mask) != ena) &&
+ (i++ < MAX_MODULE_ENABLE_WAIT))
+ udelay(1);
+
+ if (i < MAX_MODULE_ENABLE_WAIT)
+ pr_debug("cm: Module associated with clock %s ready after %d "
+ "loops\n", name, i);
+ else
+ pr_err("cm: Module associated with clock %s didn't enable in "
+ "%d tries\n", name, MAX_MODULE_ENABLE_WAIT);
+
+ return (i < MAX_MODULE_ENABLE_WAIT) ? 1 : 0;
+};
+
void __init omap2_set_globals_prcm(struct omap_globals *omap2_globals)
{
prm_base = omap2_globals->prm;
diff --git a/arch/arm/mach-omap2/sdrc.c b/arch/arm/mach-omap2/sdrc.c
index 2045441..9e3bd4f 100644
--- a/arch/arm/mach-omap2/sdrc.c
+++ b/arch/arm/mach-omap2/sdrc.c
@@ -32,7 +32,7 @@
#include <mach/sdrc.h>
#include "sdrc.h"
-static struct omap_sdrc_params *sdrc_init_params;
+static struct omap_sdrc_params *sdrc_init_params_cs0, *sdrc_init_params_cs1;
void __iomem *omap2_sdrc_base;
void __iomem *omap2_sms_base;
@@ -45,33 +45,49 @@
/**
* omap2_sdrc_get_params - return SDRC register values for a given clock rate
* @r: SDRC clock rate (in Hz)
+ * @sdrc_cs0: chip select 0 ram timings **
+ * @sdrc_cs1: chip select 1 ram timings **
*
* Return pre-calculated values for the SDRC_ACTIM_CTRLA,
- * SDRC_ACTIM_CTRLB, SDRC_RFR_CTRL, and SDRC_MR registers, for a given
- * SDRC clock rate 'r'. These parameters control various timing
- * delays in the SDRAM controller that are expressed in terms of the
- * number of SDRC clock cycles to wait; hence the clock rate
- * dependency. Note that sdrc_init_params must be sorted rate
- * descending. Also assumes that both chip-selects use the same
- * timing parameters. Returns a struct omap_sdrc_params * upon
- * success, or NULL upon failure.
+ * SDRC_ACTIM_CTRLB, SDRC_RFR_CTRL and SDRC_MR registers in sdrc_cs[01]
+ * structs,for a given SDRC clock rate 'r'.
+ * These parameters control various timing delays in the SDRAM controller
+ * that are expressed in terms of the number of SDRC clock cycles to
+ * wait; hence the clock rate dependency.
+ *
+ * Supports 2 different timing parameters for both chip selects.
+ *
+ * Note 1: the sdrc_init_params_cs[01] must be sorted rate descending.
+ * Note 2: If sdrc_init_params_cs_1 is not NULL it must be of same size
+ * as sdrc_init_params_cs_0.
+ *
+ * Fills in the struct omap_sdrc_params * for each chip select.
+ * Returns 0 upon success or -1 upon failure.
*/
-struct omap_sdrc_params *omap2_sdrc_get_params(unsigned long r)
+int omap2_sdrc_get_params(unsigned long r,
+ struct omap_sdrc_params **sdrc_cs0,
+ struct omap_sdrc_params **sdrc_cs1)
{
- struct omap_sdrc_params *sp;
+ struct omap_sdrc_params *sp0, *sp1;
- if (!sdrc_init_params)
- return NULL;
+ if (!sdrc_init_params_cs0)
+ return -1;
- sp = sdrc_init_params;
+ sp0 = sdrc_init_params_cs0;
+ sp1 = sdrc_init_params_cs1;
- while (sp->rate && sp->rate != r)
- sp++;
+ while (sp0->rate && sp0->rate != r) {
+ sp0++;
+ if (sdrc_init_params_cs1)
+ sp1++;
+ }
- if (!sp->rate)
- return NULL;
+ if (!sp0->rate)
+ return -1;
- return sp;
+ *sdrc_cs0 = sp0;
+ *sdrc_cs1 = sp1;
+ return 0;
}
@@ -83,13 +99,15 @@
/**
* omap2_sdrc_init - initialize SMS, SDRC devices on boot
- * @sp: pointer to a null-terminated list of struct omap_sdrc_params
+ * @sdrc_cs[01]: pointers to a null-terminated list of struct omap_sdrc_params
+ * Support for 2 chip selects timings
*
* Turn on smart idle modes for SDRAM scheduler and controller.
* Program a known-good configuration for the SDRC to deal with buggy
* bootloaders.
*/
-void __init omap2_sdrc_init(struct omap_sdrc_params *sp)
+void __init omap2_sdrc_init(struct omap_sdrc_params *sdrc_cs0,
+ struct omap_sdrc_params *sdrc_cs1)
{
u32 l;
@@ -103,11 +121,15 @@
l |= (0x2 << 3);
sdrc_write_reg(l, SDRC_SYSCONFIG);
- sdrc_init_params = sp;
+ sdrc_init_params_cs0 = sdrc_cs0;
+ sdrc_init_params_cs1 = sdrc_cs1;
/* XXX Enable SRFRONIDLEREQ here also? */
+ /*
+ * PWDENA should not be set due to 34xx erratum 1.150 - PWDENA
+ * can cause random memory corruption
+ */
l = (1 << SDRC_POWER_EXTCLKDIS_SHIFT) |
- (1 << SDRC_POWER_PWDENA_SHIFT) |
(1 << SDRC_POWER_PAGEPOLICY_SHIFT);
sdrc_write_reg(l, SDRC_POWER);
}
diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c
index b094c15..a7421a5 100644
--- a/arch/arm/mach-omap2/serial.c
+++ b/arch/arm/mach-omap2/serial.c
@@ -54,6 +54,7 @@
struct plat_serial8250_port *p;
struct list_head node;
+ struct platform_device pdev;
#if defined(CONFIG_ARCH_OMAP3) && defined(CONFIG_PM)
int context_valid;
@@ -68,10 +69,9 @@
#endif
};
-static struct omap_uart_state omap_uart[OMAP_MAX_NR_PORTS];
static LIST_HEAD(uart_list);
-static struct plat_serial8250_port serial_platform_data[] = {
+static struct plat_serial8250_port serial_platform_data0[] = {
{
.membase = IO_ADDRESS(OMAP_UART1_BASE),
.mapbase = OMAP_UART1_BASE,
@@ -81,6 +81,12 @@
.regshift = 2,
.uartclk = OMAP24XX_BASE_BAUD * 16,
}, {
+ .flags = 0
+ }
+};
+
+static struct plat_serial8250_port serial_platform_data1[] = {
+ {
.membase = IO_ADDRESS(OMAP_UART2_BASE),
.mapbase = OMAP_UART2_BASE,
.irq = 73,
@@ -89,6 +95,12 @@
.regshift = 2,
.uartclk = OMAP24XX_BASE_BAUD * 16,
}, {
+ .flags = 0
+ }
+};
+
+static struct plat_serial8250_port serial_platform_data2[] = {
+ {
.membase = IO_ADDRESS(OMAP_UART3_BASE),
.mapbase = OMAP_UART3_BASE,
.irq = 74,
@@ -217,6 +229,40 @@
clk_disable(uart->fck);
}
+static void omap_uart_enable_wakeup(struct omap_uart_state *uart)
+{
+ /* Set wake-enable bit */
+ if (uart->wk_en && uart->wk_mask) {
+ u32 v = __raw_readl(uart->wk_en);
+ v |= uart->wk_mask;
+ __raw_writel(v, uart->wk_en);
+ }
+
+ /* Ensure IOPAD wake-enables are set */
+ if (cpu_is_omap34xx() && uart->padconf) {
+ u16 v = omap_ctrl_readw(uart->padconf);
+ v |= OMAP3_PADCONF_WAKEUPENABLE0;
+ omap_ctrl_writew(v, uart->padconf);
+ }
+}
+
+static void omap_uart_disable_wakeup(struct omap_uart_state *uart)
+{
+ /* Clear wake-enable bit */
+ if (uart->wk_en && uart->wk_mask) {
+ u32 v = __raw_readl(uart->wk_en);
+ v &= ~uart->wk_mask;
+ __raw_writel(v, uart->wk_en);
+ }
+
+ /* Ensure IOPAD wake-enables are cleared */
+ if (cpu_is_omap34xx() && uart->padconf) {
+ u16 v = omap_ctrl_readw(uart->padconf);
+ v &= ~OMAP3_PADCONF_WAKEUPENABLE0;
+ omap_ctrl_writew(v, uart->padconf);
+ }
+}
+
static void omap_uart_smart_idle_enable(struct omap_uart_state *uart,
int enable)
{
@@ -246,6 +292,11 @@
static void omap_uart_allow_sleep(struct omap_uart_state *uart)
{
+ if (device_may_wakeup(&uart->pdev.dev))
+ omap_uart_enable_wakeup(uart);
+ else
+ omap_uart_disable_wakeup(uart);
+
if (!uart->clocked)
return;
@@ -292,7 +343,6 @@
/* Check for normal UART wakeup */
if (__raw_readl(uart->wk_st) & uart->wk_mask)
omap_uart_block_sleep(uart);
-
return;
}
}
@@ -346,16 +396,13 @@
return IRQ_NONE;
}
-static u32 sleep_timeout = DEFAULT_TIMEOUT;
-
static void omap_uart_idle_init(struct omap_uart_state *uart)
{
- u32 v;
struct plat_serial8250_port *p = uart->p;
int ret;
uart->can_sleep = 0;
- uart->timeout = sleep_timeout;
+ uart->timeout = DEFAULT_TIMEOUT;
setup_timer(&uart->timer, omap_uart_idle_timer,
(unsigned long) uart);
mod_timer(&uart->timer, jiffies + uart->timeout);
@@ -413,76 +460,101 @@
uart->padconf = 0;
}
- /* Set wake-enable bit */
- if (uart->wk_en && uart->wk_mask) {
- v = __raw_readl(uart->wk_en);
- v |= uart->wk_mask;
- __raw_writel(v, uart->wk_en);
- }
-
- /* Ensure IOPAD wake-enables are set */
- if (cpu_is_omap34xx() && uart->padconf) {
- u16 v;
-
- v = omap_ctrl_readw(uart->padconf);
- v |= OMAP3_PADCONF_WAKEUPENABLE0;
- omap_ctrl_writew(v, uart->padconf);
- }
-
p->flags |= UPF_SHARE_IRQ;
ret = request_irq(p->irq, omap_uart_interrupt, IRQF_SHARED,
"serial idle", (void *)uart);
WARN_ON(ret);
}
-static ssize_t sleep_timeout_show(struct kobject *kobj,
- struct kobj_attribute *attr,
- char *buf)
+void omap_uart_enable_irqs(int enable)
{
- return sprintf(buf, "%u\n", sleep_timeout / HZ);
+ int ret;
+ struct omap_uart_state *uart;
+
+ list_for_each_entry(uart, &uart_list, node) {
+ if (enable)
+ ret = request_irq(uart->p->irq, omap_uart_interrupt,
+ IRQF_SHARED, "serial idle", (void *)uart);
+ else
+ free_irq(uart->p->irq, (void *)uart);
+ }
}
-static ssize_t sleep_timeout_store(struct kobject *kobj,
- struct kobj_attribute *attr,
+static ssize_t sleep_timeout_show(struct device *dev,
+ struct device_attribute *attr,
+ char *buf)
+{
+ struct platform_device *pdev = container_of(dev,
+ struct platform_device, dev);
+ struct omap_uart_state *uart = container_of(pdev,
+ struct omap_uart_state, pdev);
+
+ return sprintf(buf, "%u\n", uart->timeout / HZ);
+}
+
+static ssize_t sleep_timeout_store(struct device *dev,
+ struct device_attribute *attr,
const char *buf, size_t n)
{
- struct omap_uart_state *uart;
+ struct platform_device *pdev = container_of(dev,
+ struct platform_device, dev);
+ struct omap_uart_state *uart = container_of(pdev,
+ struct omap_uart_state, pdev);
unsigned int value;
if (sscanf(buf, "%u", &value) != 1) {
printk(KERN_ERR "sleep_timeout_store: Invalid value\n");
return -EINVAL;
}
- sleep_timeout = value * HZ;
- list_for_each_entry(uart, &uart_list, node) {
- uart->timeout = sleep_timeout;
- if (uart->timeout)
- mod_timer(&uart->timer, jiffies + uart->timeout);
- else
- /* A zero value means disable timeout feature */
- omap_uart_block_sleep(uart);
- }
+
+ uart->timeout = value * HZ;
+ if (uart->timeout)
+ mod_timer(&uart->timer, jiffies + uart->timeout);
+ else
+ /* A zero value means disable timeout feature */
+ omap_uart_block_sleep(uart);
+
return n;
}
-static struct kobj_attribute sleep_timeout_attr =
- __ATTR(sleep_timeout, 0644, sleep_timeout_show, sleep_timeout_store);
-
+DEVICE_ATTR(sleep_timeout, 0644, sleep_timeout_show, sleep_timeout_store);
+#define DEV_CREATE_FILE(dev, attr) WARN_ON(device_create_file(dev, attr))
#else
static inline void omap_uart_idle_init(struct omap_uart_state *uart) {}
+#define DEV_CREATE_FILE(dev, attr)
#endif /* CONFIG_PM */
-static struct platform_device serial_device = {
- .name = "serial8250",
- .id = PLAT8250_DEV_PLATFORM,
- .dev = {
- .platform_data = serial_platform_data,
+static struct omap_uart_state omap_uart[OMAP_MAX_NR_PORTS] = {
+ {
+ .pdev = {
+ .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM,
+ .dev = {
+ .platform_data = serial_platform_data0,
+ },
+ },
+ }, {
+ .pdev = {
+ .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM1,
+ .dev = {
+ .platform_data = serial_platform_data1,
+ },
+ },
+ }, {
+ .pdev = {
+ .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM2,
+ .dev = {
+ .platform_data = serial_platform_data2,
+ },
+ },
},
};
void __init omap_serial_init(void)
{
- int i, err;
+ int i;
const struct omap_uart_config *info;
char name[16];
@@ -496,14 +568,12 @@
if (info == NULL)
return;
- if (cpu_is_omap44xx()) {
- for (i = 0; i < OMAP_MAX_NR_PORTS; i++)
- serial_platform_data[i].irq += 32;
- }
for (i = 0; i < OMAP_MAX_NR_PORTS; i++) {
- struct plat_serial8250_port *p = serial_platform_data + i;
struct omap_uart_state *uart = &omap_uart[i];
+ struct platform_device *pdev = &uart->pdev;
+ struct device *dev = &pdev->dev;
+ struct plat_serial8250_port *p = dev->platform_data;
if (!(info->enabled_uarts & (1 << i))) {
p->membase = NULL;
@@ -531,20 +601,21 @@
uart->num = i;
p->private_data = uart;
uart->p = p;
- list_add(&uart->node, &uart_list);
+ list_add_tail(&uart->node, &uart_list);
+
+ if (cpu_is_omap44xx())
+ p->irq += 32;
omap_uart_enable_clocks(uart);
omap_uart_reset(uart);
omap_uart_idle_init(uart);
+
+ if (WARN_ON(platform_device_register(pdev)))
+ continue;
+ if ((cpu_is_omap34xx() && uart->padconf) ||
+ (uart->wk_en && uart->wk_mask)) {
+ device_init_wakeup(dev, true);
+ DEV_CREATE_FILE(dev, &dev_attr_sleep_timeout);
+ }
}
-
- err = platform_device_register(&serial_device);
-
-#ifdef CONFIG_PM
- if (!err)
- err = sysfs_create_file(&serial_device.dev.kobj,
- &sleep_timeout_attr.attr);
-#endif
-
}
-
diff --git a/arch/arm/mach-omap2/sram34xx.S b/arch/arm/mach-omap2/sram34xx.S
index f41f8d9..82aa4a3 100644
--- a/arch/arm/mach-omap2/sram34xx.S
+++ b/arch/arm/mach-omap2/sram34xx.S
@@ -36,7 +36,7 @@
.text
-/* r4 parameters */
+/* r1 parameters */
#define SDRC_NO_UNLOCK_DLL 0x0
#define SDRC_UNLOCK_DLL 0x1
@@ -58,7 +58,6 @@
/* SDRC_POWER bit settings */
#define SRFRONIDLEREQ_MASK 0x40
-#define PWDENA_MASK 0x4
/* CM_IDLEST1_CORE bit settings */
#define ST_SDRC_MASK 0x2
@@ -71,41 +70,72 @@
/*
* omap3_sram_configure_core_dpll - change DPLL3 M2 divider
- * r0 = new SDRC_RFR_CTRL register contents
- * r1 = new SDRC_ACTIM_CTRLA register contents
- * r2 = new SDRC_ACTIM_CTRLB register contents
- * r3 = new M2 divider setting (only 1 and 2 supported right now)
- * r4 = unlock SDRC DLL? (1 = yes, 0 = no). Only unlock DLL for
- * SDRC rates < 83MHz
- * r5 = number of MPU cycles to wait for SDRC to stabilize after
- * reprogramming the SDRC when switching to a slower MPU speed
- * r6 = new SDRC_MR_0 register value
- * r7 = increasing SDRC rate? (1 = yes, 0 = no)
*
+ * Params passed in registers:
+ * r0 = new M2 divider setting (only 1 and 2 supported right now)
+ * r1 = unlock SDRC DLL? (1 = yes, 0 = no). Only unlock DLL for
+ * SDRC rates < 83MHz
+ * r2 = number of MPU cycles to wait for SDRC to stabilize after
+ * reprogramming the SDRC when switching to a slower MPU speed
+ * r3 = increasing SDRC rate? (1 = yes, 0 = no)
+ *
+ * Params passed via the stack. The needed params will be copied in SRAM
+ * before use by the code in SRAM (SDRAM is not accessible during SDRC
+ * reconfiguration):
+ * new SDRC_RFR_CTRL_0 register contents
+ * new SDRC_ACTIM_CTRL_A_0 register contents
+ * new SDRC_ACTIM_CTRL_B_0 register contents
+ * new SDRC_MR_0 register value
+ * new SDRC_RFR_CTRL_1 register contents
+ * new SDRC_ACTIM_CTRL_A_1 register contents
+ * new SDRC_ACTIM_CTRL_B_1 register contents
+ * new SDRC_MR_1 register value
+ *
+ * If the param SDRC_RFR_CTRL_1 is 0, the parameters
+ * are not programmed into the SDRC CS1 registers
*/
ENTRY(omap3_sram_configure_core_dpll)
stmfd sp!, {r1-r12, lr} @ store regs to stack
- ldr r4, [sp, #52] @ pull extra args off the stack
- ldr r5, [sp, #56] @ load extra args from the stack
- ldr r6, [sp, #60] @ load extra args from the stack
- ldr r7, [sp, #64] @ load extra args from the stack
+
+ @ pull the extra args off the stack
+ @ and store them in SRAM
+ ldr r4, [sp, #52]
+ str r4, omap_sdrc_rfr_ctrl_0_val
+ ldr r4, [sp, #56]
+ str r4, omap_sdrc_actim_ctrl_a_0_val
+ ldr r4, [sp, #60]
+ str r4, omap_sdrc_actim_ctrl_b_0_val
+ ldr r4, [sp, #64]
+ str r4, omap_sdrc_mr_0_val
+ ldr r4, [sp, #68]
+ str r4, omap_sdrc_rfr_ctrl_1_val
+ cmp r4, #0 @ if SDRC_RFR_CTRL_1 is 0,
+ beq skip_cs1_params @ do not use cs1 params
+ ldr r4, [sp, #72]
+ str r4, omap_sdrc_actim_ctrl_a_1_val
+ ldr r4, [sp, #76]
+ str r4, omap_sdrc_actim_ctrl_b_1_val
+ ldr r4, [sp, #80]
+ str r4, omap_sdrc_mr_1_val
+skip_cs1_params:
dsb @ flush buffered writes to interconnect
- cmp r7, #1 @ if increasing SDRC clk rate,
+
+ cmp r3, #1 @ if increasing SDRC clk rate,
bleq configure_sdrc @ program the SDRC regs early (for RFR)
- cmp r4, #SDRC_UNLOCK_DLL @ set the intended DLL state
+ cmp r1, #SDRC_UNLOCK_DLL @ set the intended DLL state
bleq unlock_dll
blne lock_dll
bl sdram_in_selfrefresh @ put SDRAM in self refresh, idle SDRC
bl configure_core_dpll @ change the DPLL3 M2 divider
+ mov r12, r2
+ bl wait_clk_stable @ wait for SDRC to stabilize
bl enable_sdrc @ take SDRC out of idle
- cmp r4, #SDRC_UNLOCK_DLL @ wait for DLL status to change
+ cmp r1, #SDRC_UNLOCK_DLL @ wait for DLL status to change
bleq wait_dll_unlock
blne wait_dll_lock
- cmp r7, #1 @ if increasing SDRC clk rate,
+ cmp r3, #1 @ if increasing SDRC clk rate,
beq return_to_sdram @ return to SDRAM code, otherwise,
bl configure_sdrc @ reprogram SDRC regs now
- mov r12, r5
- bl wait_clk_stable @ wait for SDRC to stabilize
return_to_sdram:
isb @ prevent speculative exec past here
mov r0, #0 @ return value
@@ -113,7 +143,7 @@
unlock_dll:
ldr r11, omap3_sdrc_dlla_ctrl
ldr r12, [r11]
- and r12, r12, #FIXEDDELAY_MASK
+ bic r12, r12, #FIXEDDELAY_MASK
orr r12, r12, #FIXEDDELAY_DEFAULT
orr r12, r12, #DLLIDLE_MASK
str r12, [r11] @ (no OCP barrier needed)
@@ -129,7 +159,6 @@
ldr r12, [r11] @ read the contents of SDRC_POWER
mov r9, r12 @ keep a copy of SDRC_POWER bits
orr r12, r12, #SRFRONIDLEREQ_MASK @ enable self refresh on idle
- bic r12, r12, #PWDENA_MASK @ clear PWDENA
str r12, [r11] @ write back to SDRC_POWER register
ldr r12, [r11] @ posted-write barrier for SDRC
idle_sdrc:
@@ -149,7 +178,7 @@
ldr r12, [r11]
ldr r10, core_m2_mask_val @ modify m2 for core dpll
and r12, r12, r10
- orr r12, r12, r3, lsl #CORE_DPLL_CLKOUT_DIV_SHIFT
+ orr r12, r12, r0, lsl #CORE_DPLL_CLKOUT_DIV_SHIFT
str r12, [r11]
ldr r12, [r11] @ posted-write barrier for CM
bx lr
@@ -187,15 +216,34 @@
bne wait_dll_unlock
bx lr
configure_sdrc:
- ldr r11, omap3_sdrc_rfr_ctrl
- str r0, [r11]
- ldr r11, omap3_sdrc_actim_ctrla
- str r1, [r11]
- ldr r11, omap3_sdrc_actim_ctrlb
- str r2, [r11]
+ ldr r12, omap_sdrc_rfr_ctrl_0_val @ fetch value from SRAM
+ ldr r11, omap3_sdrc_rfr_ctrl_0 @ fetch addr from SRAM
+ str r12, [r11] @ store
+ ldr r12, omap_sdrc_actim_ctrl_a_0_val
+ ldr r11, omap3_sdrc_actim_ctrl_a_0
+ str r12, [r11]
+ ldr r12, omap_sdrc_actim_ctrl_b_0_val
+ ldr r11, omap3_sdrc_actim_ctrl_b_0
+ str r12, [r11]
+ ldr r12, omap_sdrc_mr_0_val
ldr r11, omap3_sdrc_mr_0
- str r6, [r11]
- ldr r6, [r11] @ posted-write barrier for SDRC
+ str r12, [r11]
+ ldr r12, omap_sdrc_rfr_ctrl_1_val
+ cmp r12, #0 @ if SDRC_RFR_CTRL_1 is 0,
+ beq skip_cs1_prog @ do not program cs1 params
+ ldr r11, omap3_sdrc_rfr_ctrl_1
+ str r12, [r11]
+ ldr r12, omap_sdrc_actim_ctrl_a_1_val
+ ldr r11, omap3_sdrc_actim_ctrl_a_1
+ str r12, [r11]
+ ldr r12, omap_sdrc_actim_ctrl_b_1_val
+ ldr r11, omap3_sdrc_actim_ctrl_b_1
+ str r12, [r11]
+ ldr r12, omap_sdrc_mr_1_val
+ ldr r11, omap3_sdrc_mr_1
+ str r12, [r11]
+skip_cs1_prog:
+ ldr r12, [r11] @ posted-write barrier for SDRC
bx lr
omap3_sdrc_power:
@@ -206,14 +254,40 @@
.word OMAP34XX_CM_REGADDR(CORE_MOD, CM_IDLEST)
omap3_cm_iclken1_core:
.word OMAP34XX_CM_REGADDR(CORE_MOD, CM_ICLKEN1)
-omap3_sdrc_rfr_ctrl:
+
+omap3_sdrc_rfr_ctrl_0:
.word OMAP34XX_SDRC_REGADDR(SDRC_RFR_CTRL_0)
-omap3_sdrc_actim_ctrla:
+omap3_sdrc_rfr_ctrl_1:
+ .word OMAP34XX_SDRC_REGADDR(SDRC_RFR_CTRL_1)
+omap3_sdrc_actim_ctrl_a_0:
.word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_A_0)
-omap3_sdrc_actim_ctrlb:
+omap3_sdrc_actim_ctrl_a_1:
+ .word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_A_1)
+omap3_sdrc_actim_ctrl_b_0:
.word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_B_0)
+omap3_sdrc_actim_ctrl_b_1:
+ .word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_B_1)
omap3_sdrc_mr_0:
.word OMAP34XX_SDRC_REGADDR(SDRC_MR_0)
+omap3_sdrc_mr_1:
+ .word OMAP34XX_SDRC_REGADDR(SDRC_MR_1)
+omap_sdrc_rfr_ctrl_0_val:
+ .word 0xDEADBEEF
+omap_sdrc_rfr_ctrl_1_val:
+ .word 0xDEADBEEF
+omap_sdrc_actim_ctrl_a_0_val:
+ .word 0xDEADBEEF
+omap_sdrc_actim_ctrl_a_1_val:
+ .word 0xDEADBEEF
+omap_sdrc_actim_ctrl_b_0_val:
+ .word 0xDEADBEEF
+omap_sdrc_actim_ctrl_b_1_val:
+ .word 0xDEADBEEF
+omap_sdrc_mr_0_val:
+ .word 0xDEADBEEF
+omap_sdrc_mr_1_val:
+ .word 0xDEADBEEF
+
omap3_sdrc_dlla_status:
.word OMAP34XX_SDRC_REGADDR(SDRC_DLLA_STATUS)
omap3_sdrc_dlla_ctrl:
@@ -223,3 +297,4 @@
ENTRY(omap3_sram_configure_core_dpll_sz)
.word . - omap3_sram_configure_core_dpll
+
diff --git a/arch/arm/mach-u300/core.c b/arch/arm/mach-u300/core.c
index 7936085..2e9b8cc 100644
--- a/arch/arm/mach-u300/core.c
+++ b/arch/arm/mach-u300/core.c
@@ -510,7 +510,7 @@
}
};
-static void u300_init_check_chip(void)
+static void __init u300_init_check_chip(void)
{
u16 val;
diff --git a/arch/arm/mm/init.c b/arch/arm/mm/init.c
index 8277802..3a7279c 100644
--- a/arch/arm/mm/init.c
+++ b/arch/arm/mm/init.c
@@ -120,6 +120,32 @@
printk("%d pages swap cached\n", cached);
}
+static void __init find_node_limits(int node, struct meminfo *mi,
+ unsigned long *min, unsigned long *max_low, unsigned long *max_high)
+{
+ int i;
+
+ *min = -1UL;
+ *max_low = *max_high = 0;
+
+ for_each_nodebank(i, mi, node) {
+ struct membank *bank = &mi->bank[i];
+ unsigned long start, end;
+
+ start = bank_pfn_start(bank);
+ end = bank_pfn_end(bank);
+
+ if (*min > start)
+ *min = start;
+ if (*max_high < end)
+ *max_high = end;
+ if (bank->highmem)
+ continue;
+ if (*max_low < end)
+ *max_low = end;
+ }
+}
+
/*
* FIXME: We really want to avoid allocating the bootmap bitmap
* over the top of the initrd. Hopefully, this is located towards
@@ -210,41 +236,25 @@
#endif
}
-static unsigned long __init bootmem_init_node(int node, struct meminfo *mi)
+static void __init bootmem_init_node(int node, struct meminfo *mi,
+ unsigned long start_pfn, unsigned long end_pfn)
{
- unsigned long start_pfn, end_pfn, boot_pfn;
+ unsigned long boot_pfn;
unsigned int boot_pages;
pg_data_t *pgdat;
int i;
- start_pfn = -1UL;
- end_pfn = 0;
-
/*
- * Calculate the pfn range, and map the memory banks for this node.
+ * Map the memory banks for this node.
*/
for_each_nodebank(i, mi, node) {
struct membank *bank = &mi->bank[i];
- unsigned long start, end;
- start = bank_pfn_start(bank);
- end = bank_pfn_end(bank);
-
- if (start_pfn > start)
- start_pfn = start;
- if (end_pfn < end)
- end_pfn = end;
-
- map_memory_bank(bank);
+ if (!bank->highmem)
+ map_memory_bank(bank);
}
/*
- * If there is no memory in this node, ignore it.
- */
- if (end_pfn == 0)
- return end_pfn;
-
- /*
* Allocate the bootmem bitmap page.
*/
boot_pages = bootmem_bootmap_pages(end_pfn - start_pfn);
@@ -260,7 +270,8 @@
for_each_nodebank(i, mi, node) {
struct membank *bank = &mi->bank[i];
- free_bootmem_node(pgdat, bank_phys_start(bank), bank_phys_size(bank));
+ if (!bank->highmem)
+ free_bootmem_node(pgdat, bank_phys_start(bank), bank_phys_size(bank));
memory_present(node, bank_pfn_start(bank), bank_pfn_end(bank));
}
@@ -269,8 +280,6 @@
*/
reserve_bootmem_node(pgdat, boot_pfn << PAGE_SHIFT,
boot_pages << PAGE_SHIFT, BOOTMEM_DEFAULT);
-
- return end_pfn;
}
static void __init bootmem_reserve_initrd(int node)
@@ -297,33 +306,39 @@
static void __init bootmem_free_node(int node, struct meminfo *mi)
{
unsigned long zone_size[MAX_NR_ZONES], zhole_size[MAX_NR_ZONES];
- unsigned long start_pfn, end_pfn;
- pg_data_t *pgdat = NODE_DATA(node);
+ unsigned long min, max_low, max_high;
int i;
- start_pfn = pgdat->bdata->node_min_pfn;
- end_pfn = pgdat->bdata->node_low_pfn;
+ find_node_limits(node, mi, &min, &max_low, &max_high);
/*
* initialise the zones within this node.
*/
memset(zone_size, 0, sizeof(zone_size));
- memset(zhole_size, 0, sizeof(zhole_size));
/*
* The size of this node has already been determined. If we need
* to do anything fancy with the allocation of this memory to the
* zones, now is the time to do it.
*/
- zone_size[0] = end_pfn - start_pfn;
+ zone_size[0] = max_low - min;
+#ifdef CONFIG_HIGHMEM
+ zone_size[ZONE_HIGHMEM] = max_high - max_low;
+#endif
/*
* For each bank in this node, calculate the size of the holes.
* holes = node_size - sum(bank_sizes_in_node)
*/
- zhole_size[0] = zone_size[0];
- for_each_nodebank(i, mi, node)
- zhole_size[0] -= bank_pfn_size(&mi->bank[i]);
+ memcpy(zhole_size, zone_size, sizeof(zhole_size));
+ for_each_nodebank(i, mi, node) {
+ int idx = 0;
+#ifdef CONFIG_HIGHMEM
+ if (mi->bank[i].highmem)
+ idx = ZONE_HIGHMEM;
+#endif
+ zhole_size[idx] -= bank_pfn_size(&mi->bank[i]);
+ }
/*
* Adjust the sizes according to any special requirements for
@@ -331,13 +346,13 @@
*/
arch_adjust_zones(node, zone_size, zhole_size);
- free_area_init_node(node, zone_size, start_pfn, zhole_size);
+ free_area_init_node(node, zone_size, min, zhole_size);
}
void __init bootmem_init(void)
{
struct meminfo *mi = &meminfo;
- unsigned long memend_pfn = 0;
+ unsigned long min, max_low, max_high;
int node, initrd_node;
/*
@@ -345,11 +360,29 @@
*/
initrd_node = check_initrd(mi);
+ max_low = max_high = 0;
+
/*
* Run through each node initialising the bootmem allocator.
*/
for_each_node(node) {
- unsigned long end_pfn = bootmem_init_node(node, mi);
+ unsigned long node_low, node_high;
+
+ find_node_limits(node, mi, &min, &node_low, &node_high);
+
+ if (node_low > max_low)
+ max_low = node_low;
+ if (node_high > max_high)
+ max_high = node_high;
+
+ /*
+ * If there is no memory in this node, ignore it.
+ * (We can't have nodes which have no lowmem)
+ */
+ if (node_low == 0)
+ continue;
+
+ bootmem_init_node(node, mi, min, node_low);
/*
* Reserve any special node zero regions.
@@ -362,12 +395,6 @@
*/
if (node == initrd_node)
bootmem_reserve_initrd(node);
-
- /*
- * Remember the highest memory PFN.
- */
- if (end_pfn > memend_pfn)
- memend_pfn = end_pfn;
}
/*
@@ -383,7 +410,7 @@
for_each_node(node)
bootmem_free_node(node, mi);
- high_memory = __va((memend_pfn << PAGE_SHIFT) - 1) + 1;
+ high_memory = __va((max_low << PAGE_SHIFT) - 1) + 1;
/*
* This doesn't seem to be used by the Linux memory manager any
@@ -393,7 +420,8 @@
* Note: max_low_pfn and max_pfn reflect the number of _pages_ in
* the system, not the maximum PFN.
*/
- max_pfn = max_low_pfn = memend_pfn - PHYS_PFN_OFFSET;
+ max_low_pfn = max_low - PHYS_PFN_OFFSET;
+ max_pfn = max_high - PHYS_PFN_OFFSET;
}
static inline int free_area(unsigned long pfn, unsigned long end, char *s)
diff --git a/arch/arm/mm/mmu.c b/arch/arm/mm/mmu.c
index 4722582..4426ee6 100644
--- a/arch/arm/mm/mmu.c
+++ b/arch/arm/mm/mmu.c
@@ -687,13 +687,19 @@
static void __init sanity_check_meminfo(void)
{
- int i, j;
+ int i, j, highmem = 0;
for (i = 0, j = 0; i < meminfo.nr_banks; i++) {
struct membank *bank = &meminfo.bank[j];
*bank = meminfo.bank[i];
#ifdef CONFIG_HIGHMEM
+ if (__va(bank->start) > VMALLOC_MIN ||
+ __va(bank->start) < (void *)PAGE_OFFSET)
+ highmem = 1;
+
+ bank->highmem = highmem;
+
/*
* Split those memory banks which are partially overlapping
* the vmalloc area greatly simplifying things later.
@@ -714,6 +720,7 @@
i++;
bank[1].size -= VMALLOC_MIN - __va(bank->start);
bank[1].start = __pa(VMALLOC_MIN - 1) + 1;
+ bank[1].highmem = highmem = 1;
j++;
}
bank->size = VMALLOC_MIN - __va(bank->start);
diff --git a/arch/arm/plat-omap/cpu-omap.c b/arch/arm/plat-omap/cpu-omap.c
index 843e8af..1868c0d 100644
--- a/arch/arm/plat-omap/cpu-omap.c
+++ b/arch/arm/plat-omap/cpu-omap.c
@@ -78,10 +78,10 @@
/* Ensure desired rate is within allowed range. Some govenors
* (ondemand) will just pass target_freq=0 to get the minimum. */
- if (target_freq < policy->cpuinfo.min_freq)
- target_freq = policy->cpuinfo.min_freq;
- if (target_freq > policy->cpuinfo.max_freq)
- target_freq = policy->cpuinfo.max_freq;
+ if (target_freq < policy->min)
+ target_freq = policy->min;
+ if (target_freq > policy->max)
+ target_freq = policy->max;
freqs.old = omap_getspeed(0);
freqs.new = clk_round_rate(mpu_clk, target_freq * 1000) / 1000;
diff --git a/arch/arm/plat-omap/dma.c b/arch/arm/plat-omap/dma.c
index 7677a4a..e3ac94f 100644
--- a/arch/arm/plat-omap/dma.c
+++ b/arch/arm/plat-omap/dma.c
@@ -946,7 +946,9 @@
cur_lch = next_lch;
} while (next_lch != -1);
- } else if (cpu_class_is_omap2()) {
+ } else if (cpu_is_omap242x() ||
+ (cpu_is_omap243x() && omap_type() <= OMAP2430_REV_ES1_0)) {
+
/* Errata: Need to write lch even if not using chaining */
dma_write(lch, CLNK_CTRL(lch));
}
diff --git a/arch/arm/plat-omap/gpio.c b/arch/arm/plat-omap/gpio.c
index 26b387c..9298bc0 100644
--- a/arch/arm/plat-omap/gpio.c
+++ b/arch/arm/plat-omap/gpio.c
@@ -476,14 +476,12 @@
__raw_writel(l, reg);
}
-static int __omap_get_gpio_datain(int gpio)
+static int _get_gpio_datain(struct gpio_bank *bank, int gpio)
{
- struct gpio_bank *bank;
void __iomem *reg;
if (check_gpio(gpio) < 0)
return -EINVAL;
- bank = get_gpio_bank(gpio);
reg = bank->base;
switch (bank->method) {
#ifdef CONFIG_ARCH_OMAP1
@@ -524,6 +522,53 @@
& (1 << get_gpio_index(gpio))) != 0;
}
+static int _get_gpio_dataout(struct gpio_bank *bank, int gpio)
+{
+ void __iomem *reg;
+
+ if (check_gpio(gpio) < 0)
+ return -EINVAL;
+ reg = bank->base;
+
+ switch (bank->method) {
+#ifdef CONFIG_ARCH_OMAP1
+ case METHOD_MPUIO:
+ reg += OMAP_MPUIO_OUTPUT;
+ break;
+#endif
+#ifdef CONFIG_ARCH_OMAP15XX
+ case METHOD_GPIO_1510:
+ reg += OMAP1510_GPIO_DATA_OUTPUT;
+ break;
+#endif
+#ifdef CONFIG_ARCH_OMAP16XX
+ case METHOD_GPIO_1610:
+ reg += OMAP1610_GPIO_DATAOUT;
+ break;
+#endif
+#ifdef CONFIG_ARCH_OMAP730
+ case METHOD_GPIO_730:
+ reg += OMAP730_GPIO_DATA_OUTPUT;
+ break;
+#endif
+#ifdef CONFIG_ARCH_OMAP850
+ case METHOD_GPIO_850:
+ reg += OMAP850_GPIO_DATA_OUTPUT;
+ break;
+#endif
+#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) || \
+ defined(CONFIG_ARCH_OMAP4)
+ case METHOD_GPIO_24XX:
+ reg += OMAP24XX_GPIO_DATAOUT;
+ break;
+#endif
+ default:
+ return -EINVAL;
+ }
+
+ return (__raw_readl(reg) & (1 << get_gpio_index(gpio))) != 0;
+}
+
#define MOD_REG_BIT(reg, bit_mask, set) \
do { \
int l = __raw_readl(base + reg); \
@@ -1189,6 +1234,7 @@
struct gpio_bank *bank = get_irq_chip_data(irq);
_set_gpio_irqenable(bank, gpio, 0);
+ _set_gpio_triggering(bank, get_gpio_index(gpio), IRQ_TYPE_NONE);
}
static void gpio_unmask_irq(unsigned int irq)
@@ -1196,6 +1242,11 @@
unsigned int gpio = irq - IH_GPIO_BASE;
struct gpio_bank *bank = get_irq_chip_data(irq);
unsigned int irq_mask = 1 << get_gpio_index(gpio);
+ struct irq_desc *desc = irq_to_desc(irq);
+ u32 trigger = desc->status & IRQ_TYPE_SENSE_MASK;
+
+ if (trigger)
+ _set_gpio_triggering(bank, get_gpio_index(gpio), trigger);
/* For level-triggered GPIOs, the clearing must be done after
* the HW source is cleared, thus after the handler has run */
@@ -1350,9 +1401,49 @@
return 0;
}
+static int gpio_is_input(struct gpio_bank *bank, int mask)
+{
+ void __iomem *reg = bank->base;
+
+ switch (bank->method) {
+ case METHOD_MPUIO:
+ reg += OMAP_MPUIO_IO_CNTL;
+ break;
+ case METHOD_GPIO_1510:
+ reg += OMAP1510_GPIO_DIR_CONTROL;
+ break;
+ case METHOD_GPIO_1610:
+ reg += OMAP1610_GPIO_DIRECTION;
+ break;
+ case METHOD_GPIO_730:
+ reg += OMAP730_GPIO_DIR_CONTROL;
+ break;
+ case METHOD_GPIO_850:
+ reg += OMAP850_GPIO_DIR_CONTROL;
+ break;
+ case METHOD_GPIO_24XX:
+ reg += OMAP24XX_GPIO_OE;
+ break;
+ }
+ return __raw_readl(reg) & mask;
+}
+
static int gpio_get(struct gpio_chip *chip, unsigned offset)
{
- return __omap_get_gpio_datain(chip->base + offset);
+ struct gpio_bank *bank;
+ void __iomem *reg;
+ int gpio;
+ u32 mask;
+
+ gpio = chip->base + offset;
+ bank = get_gpio_bank(gpio);
+ reg = bank->base;
+ mask = 1 << get_gpio_index(gpio);
+
+ if (gpio_is_input(bank, mask))
+ return _get_gpio_datain(bank, gpio);
+ else
+ return _get_gpio_dataout(bank, gpio);
}
static int gpio_output(struct gpio_chip *chip, unsigned offset, int value)
@@ -1886,34 +1977,6 @@
#include <linux/debugfs.h>
#include <linux/seq_file.h>
-static int gpio_is_input(struct gpio_bank *bank, int mask)
-{
- void __iomem *reg = bank->base;
-
- switch (bank->method) {
- case METHOD_MPUIO:
- reg += OMAP_MPUIO_IO_CNTL;
- break;
- case METHOD_GPIO_1510:
- reg += OMAP1510_GPIO_DIR_CONTROL;
- break;
- case METHOD_GPIO_1610:
- reg += OMAP1610_GPIO_DIRECTION;
- break;
- case METHOD_GPIO_730:
- reg += OMAP730_GPIO_DIR_CONTROL;
- break;
- case METHOD_GPIO_850:
- reg += OMAP850_GPIO_DIR_CONTROL;
- break;
- case METHOD_GPIO_24XX:
- reg += OMAP24XX_GPIO_OE;
- break;
- }
- return __raw_readl(reg) & mask;
-}
-
-
static int dbg_gpio_show(struct seq_file *s, void *unused)
{
unsigned i, j, gpio;
diff --git a/arch/arm/plat-omap/include/mach/clock.h b/arch/arm/plat-omap/include/mach/clock.h
index f9f65e1..4b8b0d6 100644
--- a/arch/arm/plat-omap/include/mach/clock.h
+++ b/arch/arm/plat-omap/include/mach/clock.h
@@ -20,6 +20,8 @@
struct clkops {
int (*enable)(struct clk *);
void (*disable)(struct clk *);
+ void (*find_idlest)(struct clk *, void __iomem **, u8 *);
+ void (*find_companion)(struct clk *, void __iomem **, u8 *);
};
#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) || \
diff --git a/arch/arm/plat-omap/include/mach/cpu.h b/arch/arm/plat-omap/include/mach/cpu.h
index 285eaa3..11e73d9 100644
--- a/arch/arm/plat-omap/include/mach/cpu.h
+++ b/arch/arm/plat-omap/include/mach/cpu.h
@@ -378,9 +378,6 @@
#define cpu_class_is_omap2() (cpu_is_omap24xx() || cpu_is_omap34xx() || \
cpu_is_omap44xx())
-#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) || \
- defined(CONFIG_ARCH_OMAP4)
-
/* Various silicon revisions for omap2 */
#define OMAP242X_CLASS 0x24200024
#define OMAP2420_REV_ES1_0 0x24200024
@@ -436,5 +433,3 @@
int omap_chip_is(struct omap_chip_id oci);
void omap2_check_revision(void);
-
-#endif /* defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) */
diff --git a/arch/arm/plat-omap/include/mach/io.h b/arch/arm/plat-omap/include/mach/io.h
index 73f483d..21fb0ef 100644
--- a/arch/arm/plat-omap/include/mach/io.h
+++ b/arch/arm/plat-omap/include/mach/io.h
@@ -228,7 +228,8 @@
extern void omap1_init_common_hw(void);
extern void omap2_map_common_io(void);
-extern void omap2_init_common_hw(struct omap_sdrc_params *sp);
+extern void omap2_init_common_hw(struct omap_sdrc_params *sdrc_cs0,
+ struct omap_sdrc_params *sdrc_cs1);
#define __arch_ioremap(p,s,t) omap_ioremap(p,s,t)
#define __arch_iounmap(v) omap_iounmap(v)
diff --git a/arch/arm/plat-omap/include/mach/mux.h b/arch/arm/plat-omap/include/mach/mux.h
index 85a6217..80281c4 100644
--- a/arch/arm/plat-omap/include/mach/mux.h
+++ b/arch/arm/plat-omap/include/mach/mux.h
@@ -853,6 +853,10 @@
AE5_34XX_GPIO143,
H19_34XX_GPIO164_OUT,
J25_34XX_GPIO170,
+
+ /* OMAP3 SDRC CKE signals to SDR/DDR ram chips */
+ H16_34XX_SDRC_CKE0,
+ H17_34XX_SDRC_CKE1,
};
struct omap_mux_cfg {
diff --git a/arch/arm/plat-omap/include/mach/prcm.h b/arch/arm/plat-omap/include/mach/prcm.h
index 24ac3c7..cda2a70 100644
--- a/arch/arm/plat-omap/include/mach/prcm.h
+++ b/arch/arm/plat-omap/include/mach/prcm.h
@@ -25,6 +25,7 @@
u32 omap_prcm_get_reset_sources(void);
void omap_prcm_arch_reset(char mode);
+int omap2_cm_wait_idlest(void __iomem *reg, u32 mask, const char *name);
#endif
diff --git a/arch/arm/plat-omap/include/mach/sdrc.h b/arch/arm/plat-omap/include/mach/sdrc.h
index adc7352..0be18e4 100644
--- a/arch/arm/plat-omap/include/mach/sdrc.h
+++ b/arch/arm/plat-omap/include/mach/sdrc.h
@@ -30,6 +30,10 @@
#define SDRC_ACTIM_CTRL_A_0 0x09c
#define SDRC_ACTIM_CTRL_B_0 0x0a0
#define SDRC_RFR_CTRL_0 0x0a4
+#define SDRC_MR_1 0x0B4
+#define SDRC_ACTIM_CTRL_A_1 0x0C4
+#define SDRC_ACTIM_CTRL_B_1 0x0C8
+#define SDRC_RFR_CTRL_1 0x0D4
/*
* These values represent the number of memory clock cycles between
@@ -102,8 +106,11 @@
u32 mr;
};
-void __init omap2_sdrc_init(struct omap_sdrc_params *sp);
-struct omap_sdrc_params *omap2_sdrc_get_params(unsigned long r);
+void __init omap2_sdrc_init(struct omap_sdrc_params *sdrc_cs0,
+ struct omap_sdrc_params *sdrc_cs1);
+int omap2_sdrc_get_params(unsigned long r,
+ struct omap_sdrc_params **sdrc_cs0,
+ struct omap_sdrc_params **sdrc_cs1);
#ifdef CONFIG_ARCH_OMAP2
diff --git a/arch/arm/plat-omap/include/mach/serial.h b/arch/arm/plat-omap/include/mach/serial.h
index 13abd02..def0529 100644
--- a/arch/arm/plat-omap/include/mach/serial.h
+++ b/arch/arm/plat-omap/include/mach/serial.h
@@ -59,6 +59,7 @@
extern void omap_uart_prepare_suspend(void);
extern void omap_uart_prepare_idle(int num);
extern void omap_uart_resume_idle(int num);
+extern void omap_uart_enable_irqs(int enable);
#endif
#endif
diff --git a/arch/arm/plat-omap/include/mach/sram.h b/arch/arm/plat-omap/include/mach/sram.h
index 4d53cc5..8974e3f 100644
--- a/arch/arm/plat-omap/include/mach/sram.h
+++ b/arch/arm/plat-omap/include/mach/sram.h
@@ -21,11 +21,12 @@
u32 mem_type);
extern u32 omap2_set_prcm(u32 dpll_ctrl_val, u32 sdrc_rfr_val, int bypass);
-extern u32 omap3_configure_core_dpll(u32 sdrc_rfr_ctrl,
- u32 sdrc_actim_ctrla,
- u32 sdrc_actim_ctrlb, u32 m2,
- u32 unlock_dll, u32 f, u32 sdrc_mr,
- u32 inc);
+extern u32 omap3_configure_core_dpll(
+ u32 m2, u32 unlock_dll, u32 f, u32 inc,
+ u32 sdrc_rfr_ctrl_0, u32 sdrc_actim_ctrl_a_0,
+ u32 sdrc_actim_ctrl_b_0, u32 sdrc_mr_0,
+ u32 sdrc_rfr_ctrl_1, u32 sdrc_actim_ctrl_a_1,
+ u32 sdrc_actim_ctrl_b_1, u32 sdrc_mr_1);
/* Do not use these */
extern void omap1_sram_reprogram_clock(u32 ckctl, u32 dpllctl);
@@ -59,12 +60,12 @@
u32 mem_type);
extern unsigned long omap243x_sram_reprogram_sdrc_sz;
-
-extern u32 omap3_sram_configure_core_dpll(u32 sdrc_rfr_ctrl,
- u32 sdrc_actim_ctrla,
- u32 sdrc_actim_ctrlb, u32 m2,
- u32 unlock_dll, u32 f, u32 sdrc_mr,
- u32 inc);
+extern u32 omap3_sram_configure_core_dpll(
+ u32 m2, u32 unlock_dll, u32 f, u32 inc,
+ u32 sdrc_rfr_ctrl_0, u32 sdrc_actim_ctrl_a_0,
+ u32 sdrc_actim_ctrl_b_0, u32 sdrc_mr_0,
+ u32 sdrc_rfr_ctrl_1, u32 sdrc_actim_ctrl_a_1,
+ u32 sdrc_actim_ctrl_b_1, u32 sdrc_mr_1);
extern unsigned long omap3_sram_configure_core_dpll_sz;
#endif
diff --git a/arch/arm/plat-omap/sram.c b/arch/arm/plat-omap/sram.c
index 4ea7380..5eae787 100644
--- a/arch/arm/plat-omap/sram.c
+++ b/arch/arm/plat-omap/sram.c
@@ -44,9 +44,9 @@
#define OMAP2_SRAM_VA 0xe3000000
#define OMAP2_SRAM_PUB_VA (OMAP2_SRAM_VA + 0x800)
#define OMAP3_SRAM_PA 0x40200000
-#define OMAP3_SRAM_VA 0xd7000000
+#define OMAP3_SRAM_VA 0xe3000000
#define OMAP3_SRAM_PUB_PA 0x40208000
-#define OMAP3_SRAM_PUB_VA 0xd7008000
+#define OMAP3_SRAM_PUB_VA (OMAP3_SRAM_VA + 0x8000)
#define OMAP4_SRAM_PA 0x40200000 /*0x402f0000*/
#define OMAP4_SRAM_VA 0xd7000000 /*0xd70f0000*/
@@ -373,20 +373,26 @@
#ifdef CONFIG_ARCH_OMAP3
-static u32 (*_omap3_sram_configure_core_dpll)(u32 sdrc_rfr_ctrl,
- u32 sdrc_actim_ctrla,
- u32 sdrc_actim_ctrlb,
- u32 m2, u32 unlock_dll,
- u32 f, u32 sdrc_mr, u32 inc);
-u32 omap3_configure_core_dpll(u32 sdrc_rfr_ctrl, u32 sdrc_actim_ctrla,
- u32 sdrc_actim_ctrlb, u32 m2, u32 unlock_dll,
- u32 f, u32 sdrc_mr, u32 inc)
+static u32 (*_omap3_sram_configure_core_dpll)(
+ u32 m2, u32 unlock_dll, u32 f, u32 inc,
+ u32 sdrc_rfr_ctrl_0, u32 sdrc_actim_ctrl_a_0,
+ u32 sdrc_actim_ctrl_b_0, u32 sdrc_mr_0,
+ u32 sdrc_rfr_ctrl_1, u32 sdrc_actim_ctrl_a_1,
+ u32 sdrc_actim_ctrl_b_1, u32 sdrc_mr_1);
+
+u32 omap3_configure_core_dpll(u32 m2, u32 unlock_dll, u32 f, u32 inc,
+ u32 sdrc_rfr_ctrl_0, u32 sdrc_actim_ctrl_a_0,
+ u32 sdrc_actim_ctrl_b_0, u32 sdrc_mr_0,
+ u32 sdrc_rfr_ctrl_1, u32 sdrc_actim_ctrl_a_1,
+ u32 sdrc_actim_ctrl_b_1, u32 sdrc_mr_1)
{
BUG_ON(!_omap3_sram_configure_core_dpll);
- return _omap3_sram_configure_core_dpll(sdrc_rfr_ctrl,
- sdrc_actim_ctrla,
- sdrc_actim_ctrlb, m2,
- unlock_dll, f, sdrc_mr, inc);
+ return _omap3_sram_configure_core_dpll(
+ m2, unlock_dll, f, inc,
+ sdrc_rfr_ctrl_0, sdrc_actim_ctrl_a_0,
+ sdrc_actim_ctrl_b_0, sdrc_mr_0,
+ sdrc_rfr_ctrl_1, sdrc_actim_ctrl_a_1,
+ sdrc_actim_ctrl_b_1, sdrc_mr_1);
}
/* REVISIT: Should this be same as omap34xx_sram_init() after off-idle? */
diff --git a/arch/arm/plat-s3c24xx/clock-dclk.c b/arch/arm/plat-s3c24xx/clock-dclk.c
index 5b75a79..0afb217 100644
--- a/arch/arm/plat-s3c24xx/clock-dclk.c
+++ b/arch/arm/plat-s3c24xx/clock-dclk.c
@@ -129,7 +129,7 @@
/* calculate the MISCCR setting for the clock */
- if (parent == &clk_xtal)
+ if (parent == &clk_mpll)
source = S3C2410_MISCCR_CLK0_MPLL;
else if (parent == &clk_upll)
source = S3C2410_MISCCR_CLK0_UPLL;
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index 037c1e0..6553833 100644
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -527,7 +527,7 @@
config SERIAL_S3C6400
tristate "Samsung S3C6400/S3C6410 Serial port support"
- depends on SERIAL_SAMSUNG && (CPU_S3C600 || CPU_S3C6410)
+ depends on SERIAL_SAMSUNG && (CPU_S3C6400 || CPU_S3C6410)
default y
help
Serial port support for the Samsung S3C6400 and S3C6410