diff --git a/MAINTAINERS b/MAINTAINERS
index 716c548..1b1954d 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -6233,7 +6233,7 @@
 M:	Greg Kroah-Hartman <gregkh@suse.de>
 L:	linux-usb@vger.kernel.org
 W:	http://www.linux-usb.org
-T:	quilt kernel.org/pub/linux/kernel/people/gregkh/gregkh-2.6/
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6.git
 S:	Supported
 F:	Documentation/usb/
 F:	drivers/net/usb/
diff --git a/drivers/usb/core/devio.c b/drivers/usb/core/devio.c
index f1aaff6..045bb4b 100644
--- a/drivers/usb/core/devio.c
+++ b/drivers/usb/core/devio.c
@@ -965,10 +965,11 @@
 
 static int proc_connectinfo(struct dev_state *ps, void __user *arg)
 {
-	struct usbdevfs_connectinfo ci;
+	struct usbdevfs_connectinfo ci = {
+		.devnum = ps->dev->devnum,
+		.slow = ps->dev->speed == USB_SPEED_LOW
+	};
 
-	ci.devnum = ps->dev->devnum;
-	ci.slow = ps->dev->speed == USB_SPEED_LOW;
 	if (copy_to_user(arg, &ci, sizeof(ci)))
 		return -EFAULT;
 	return 0;
diff --git a/drivers/usb/gadget/Kconfig b/drivers/usb/gadget/Kconfig
index b739ca8..607d0db 100644
--- a/drivers/usb/gadget/Kconfig
+++ b/drivers/usb/gadget/Kconfig
@@ -158,7 +158,7 @@
 	boolean "Freescale Highspeed USB DR Peripheral Controller"
 	depends on FSL_SOC || ARCH_MXC
 	select USB_GADGET_DUALSPEED
-	select USB_FSL_MPH_DR_OF
+	select USB_FSL_MPH_DR_OF if OF
 	help
 	   Some of Freescale PowerPC processors have a High Speed
 	   Dual-Role(DR) USB controller, which supports device mode.
diff --git a/drivers/usb/gadget/goku_udc.h b/drivers/usb/gadget/goku_udc.h
index 566cb23..e7e0c69 100644
--- a/drivers/usb/gadget/goku_udc.h
+++ b/drivers/usb/gadget/goku_udc.h
@@ -251,7 +251,8 @@
 					got_region:1,
 					req_config:1,
 					configured:1,
-					enabled:1;
+					enabled:1,
+					registered:1;
 
 	/* pci state used to access those endpoints */
 	struct pci_dev			*pdev;
diff --git a/drivers/usb/gadget/u_serial.c b/drivers/usb/gadget/u_serial.c
index 01e5354..40f7716 100644
--- a/drivers/usb/gadget/u_serial.c
+++ b/drivers/usb/gadget/u_serial.c
@@ -105,11 +105,15 @@
 	wait_queue_head_t	close_wait;	/* wait for last close */
 
 	struct list_head	read_pool;
+	int read_started;
+	int read_allocated;
 	struct list_head	read_queue;
 	unsigned		n_read;
 	struct tasklet_struct	push;
 
 	struct list_head	write_pool;
+	int write_started;
+	int write_allocated;
 	struct gs_buf		port_write_buf;
 	wait_queue_head_t	drain_wait;	/* wait while writes drain */
 
@@ -363,6 +367,9 @@
 		struct usb_request	*req;
 		int			len;
 
+		if (port->write_started >= QUEUE_SIZE)
+			break;
+
 		req = list_entry(pool->next, struct usb_request, list);
 		len = gs_send_packet(port, req->buf, in->maxpacket);
 		if (len == 0) {
@@ -397,6 +404,8 @@
 			break;
 		}
 
+		port->write_started++;
+
 		/* abort immediately after disconnect */
 		if (!port->port_usb)
 			break;
@@ -418,7 +427,6 @@
 {
 	struct list_head	*pool = &port->read_pool;
 	struct usb_ep		*out = port->port_usb->out;
-	unsigned		started = 0;
 
 	while (!list_empty(pool)) {
 		struct usb_request	*req;
@@ -430,6 +438,9 @@
 		if (!tty)
 			break;
 
+		if (port->read_started >= QUEUE_SIZE)
+			break;
+
 		req = list_entry(pool->next, struct usb_request, list);
 		list_del(&req->list);
 		req->length = out->maxpacket;
@@ -447,13 +458,13 @@
 			list_add(&req->list, pool);
 			break;
 		}
-		started++;
+		port->read_started++;
 
 		/* abort immediately after disconnect */
 		if (!port->port_usb)
 			break;
 	}
-	return started;
+	return port->read_started;
 }
 
 /*
@@ -535,6 +546,7 @@
 		}
 recycle:
 		list_move(&req->list, &port->read_pool);
+		port->read_started--;
 	}
 
 	/* Push from tty to ldisc; without low_latency set this is handled by
@@ -587,6 +599,7 @@
 
 	spin_lock(&port->port_lock);
 	list_add(&req->list, &port->write_pool);
+	port->write_started--;
 
 	switch (req->status) {
 	default:
@@ -608,7 +621,8 @@
 	spin_unlock(&port->port_lock);
 }
 
-static void gs_free_requests(struct usb_ep *ep, struct list_head *head)
+static void gs_free_requests(struct usb_ep *ep, struct list_head *head,
+							 int *allocated)
 {
 	struct usb_request	*req;
 
@@ -616,25 +630,31 @@
 		req = list_entry(head->next, struct usb_request, list);
 		list_del(&req->list);
 		gs_free_req(ep, req);
+		if (allocated)
+			(*allocated)--;
 	}
 }
 
 static int gs_alloc_requests(struct usb_ep *ep, struct list_head *head,
-		void (*fn)(struct usb_ep *, struct usb_request *))
+		void (*fn)(struct usb_ep *, struct usb_request *),
+		int *allocated)
 {
 	int			i;
 	struct usb_request	*req;
+	int n = allocated ? QUEUE_SIZE - *allocated : QUEUE_SIZE;
 
 	/* Pre-allocate up to QUEUE_SIZE transfers, but if we can't
 	 * do quite that many this time, don't fail ... we just won't
 	 * be as speedy as we might otherwise be.
 	 */
-	for (i = 0; i < QUEUE_SIZE; i++) {
+	for (i = 0; i < n; i++) {
 		req = gs_alloc_req(ep, ep->maxpacket, GFP_ATOMIC);
 		if (!req)
 			return list_empty(head) ? -ENOMEM : 0;
 		req->complete = fn;
 		list_add_tail(&req->list, head);
+		if (allocated)
+			(*allocated)++;
 	}
 	return 0;
 }
@@ -661,14 +681,15 @@
 	 * configurations may use different endpoints with a given port;
 	 * and high speed vs full speed changes packet sizes too.
 	 */
-	status = gs_alloc_requests(ep, head, gs_read_complete);
+	status = gs_alloc_requests(ep, head, gs_read_complete,
+		&port->read_allocated);
 	if (status)
 		return status;
 
 	status = gs_alloc_requests(port->port_usb->in, &port->write_pool,
-			gs_write_complete);
+			gs_write_complete, &port->write_allocated);
 	if (status) {
-		gs_free_requests(ep, head);
+		gs_free_requests(ep, head, &port->read_allocated);
 		return status;
 	}
 
@@ -680,8 +701,9 @@
 	if (started) {
 		tty_wakeup(port->port_tty);
 	} else {
-		gs_free_requests(ep, head);
-		gs_free_requests(port->port_usb->in, &port->write_pool);
+		gs_free_requests(ep, head, &port->read_allocated);
+		gs_free_requests(port->port_usb->in, &port->write_pool,
+			&port->write_allocated);
 		status = -EIO;
 	}
 
@@ -1315,8 +1337,12 @@
 	spin_lock_irqsave(&port->port_lock, flags);
 	if (port->open_count == 0 && !port->openclose)
 		gs_buf_free(&port->port_write_buf);
-	gs_free_requests(gser->out, &port->read_pool);
-	gs_free_requests(gser->out, &port->read_queue);
-	gs_free_requests(gser->in, &port->write_pool);
+	gs_free_requests(gser->out, &port->read_pool, NULL);
+	gs_free_requests(gser->out, &port->read_queue, NULL);
+	gs_free_requests(gser->in, &port->write_pool, NULL);
+
+	port->read_allocated = port->read_started =
+		port->write_allocated = port->write_started = 0;
+
 	spin_unlock_irqrestore(&port->port_lock, flags);
 }
diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index 2391c39..6f4f8e6 100644
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -122,7 +122,7 @@
 	bool "Support for Freescale on-chip EHCI USB controller"
 	depends on USB_EHCI_HCD && FSL_SOC
 	select USB_EHCI_ROOT_HUB_TT
-	select USB_FSL_MPH_DR_OF
+	select USB_FSL_MPH_DR_OF if OF
 	---help---
 	  Variation of ARC USB block used in some Freescale chips.
 
diff --git a/drivers/usb/host/ehci-mxc.c b/drivers/usb/host/ehci-mxc.c
index ac9c4d7..bce8505 100644
--- a/drivers/usb/host/ehci-mxc.c
+++ b/drivers/usb/host/ehci-mxc.c
@@ -36,6 +36,8 @@
 static int ehci_mxc_setup(struct usb_hcd *hcd)
 {
 	struct ehci_hcd *ehci = hcd_to_ehci(hcd);
+	struct device *dev = hcd->self.controller;
+	struct mxc_usbh_platform_data *pdata = dev_get_platdata(dev);
 	int retval;
 
 	/* EHCI registers start at offset 0x100 */
@@ -63,6 +65,12 @@
 
 	ehci_reset(ehci);
 
+	/* set up the PORTSCx register */
+	ehci_writel(ehci, pdata->portsc, &ehci->regs->port_status[0]);
+
+	/* is this really needed? */
+	msleep(10);
+
 	ehci_port_power(ehci, 0);
 	return 0;
 }
@@ -114,7 +122,7 @@
 	struct mxc_usbh_platform_data *pdata = pdev->dev.platform_data;
 	struct usb_hcd *hcd;
 	struct resource *res;
-	int irq, ret, temp;
+	int irq, ret;
 	struct ehci_mxc_priv *priv;
 	struct device *dev = &pdev->dev;
 
@@ -188,10 +196,6 @@
 		clk_enable(priv->ahbclk);
 	}
 
-	/* set up the PORTSCx register */
-	ehci_writel(ehci, pdata->portsc, &ehci->regs->port_status[0]);
-	mdelay(10);
-
 	/* setup specific usb hw */
 	ret = mxc_initialize_usb_hw(pdev->id, pdata->flags);
 	if (ret < 0)
diff --git a/drivers/usb/host/ohci-jz4740.c b/drivers/usb/host/ohci-jz4740.c
index 10e1872f..931d588 100644
--- a/drivers/usb/host/ohci-jz4740.c
+++ b/drivers/usb/host/ohci-jz4740.c
@@ -273,4 +273,4 @@
 	},
 };
 
-MODULE_ALIAS("platfrom:jz4740-ohci");
+MODULE_ALIAS("platform:jz4740-ohci");
diff --git a/drivers/usb/misc/iowarrior.c b/drivers/usb/misc/iowarrior.c
index 3756641..c9078e4 100644
--- a/drivers/usb/misc/iowarrior.c
+++ b/drivers/usb/misc/iowarrior.c
@@ -553,6 +553,7 @@
 			/* needed for power consumption */
 			struct usb_config_descriptor *cfg_descriptor = &dev->udev->actconfig->desc;
 
+			memset(&info, 0, sizeof(info));
 			/* directly from the descriptor */
 			info.vendor = le16_to_cpu(dev->udev->descriptor.idVendor);
 			info.product = dev->product_id;
diff --git a/drivers/usb/misc/sisusbvga/sisusb.c b/drivers/usb/misc/sisusbvga/sisusb.c
index 70d00e9..dd573ab 100644
--- a/drivers/usb/misc/sisusbvga/sisusb.c
+++ b/drivers/usb/misc/sisusbvga/sisusb.c
@@ -3008,6 +3008,7 @@
 #else
 			x.sisusb_conactive  = 0;
 #endif
+			memset(x.sisusb_reserved, 0, sizeof(x.sisusb_reserved));
 
 			if (copy_to_user((void __user *)arg, &x, sizeof(x)))
 				retval = -EFAULT;
diff --git a/drivers/usb/musb/blackfin.c b/drivers/usb/musb/blackfin.c
index 611a9d2..fcb5206 100644
--- a/drivers/usb/musb/blackfin.c
+++ b/drivers/usb/musb/blackfin.c
@@ -171,8 +171,9 @@
 	}
 
 	/* Start sampling ID pin, when plug is removed from MUSB */
-	if (is_otg_enabled(musb) && (musb->xceiv->state == OTG_STATE_B_IDLE
-		|| musb->xceiv->state == OTG_STATE_A_WAIT_BCON)) {
+	if ((is_otg_enabled(musb) && (musb->xceiv->state == OTG_STATE_B_IDLE
+		|| musb->xceiv->state == OTG_STATE_A_WAIT_BCON)) ||
+		(musb->int_usb & MUSB_INTR_DISCONNECT && is_host_active(musb))) {
 		mod_timer(&musb_conn_timer, jiffies + TIMER_DELAY);
 		musb->a_wait_bcon = TIMER_DELAY;
 	}
@@ -323,30 +324,8 @@
 	return -EIO;
 }
 
-int __init musb_platform_init(struct musb *musb, void *board_data)
+static void musb_platform_reg_init(struct musb *musb)
 {
-
-	/*
-	 * Rev 1.0 BF549 EZ-KITs require PE7 to be high for both DEVICE
-	 * and OTG HOST modes, while rev 1.1 and greater require PE7 to
-	 * be low for DEVICE mode and high for HOST mode. We set it high
-	 * here because we are in host mode
-	 */
-
-	if (gpio_request(musb->config->gpio_vrsel, "USB_VRSEL")) {
-		printk(KERN_ERR "Failed ro request USB_VRSEL GPIO_%d \n",
-			musb->config->gpio_vrsel);
-		return -ENODEV;
-	}
-	gpio_direction_output(musb->config->gpio_vrsel, 0);
-
-	usb_nop_xceiv_register();
-	musb->xceiv = otg_get_transceiver();
-	if (!musb->xceiv) {
-		gpio_free(musb->config->gpio_vrsel);
-		return -ENODEV;
-	}
-
 	if (ANOMALY_05000346) {
 		bfin_write_USB_APHY_CALIB(ANOMALY_05000346_value);
 		SSYNC();
@@ -358,7 +337,8 @@
 	}
 
 	/* Configure PLL oscillator register */
-	bfin_write_USB_PLLOSC_CTRL(0x30a8);
+	bfin_write_USB_PLLOSC_CTRL(0x3080 |
+			((480/musb->config->clkin) << 1));
 	SSYNC();
 
 	bfin_write_USB_SRP_CLKDIV((get_sclk()/1000) / 32 - 1);
@@ -380,6 +360,33 @@
 				EP2_RX_ENA | EP3_RX_ENA | EP4_RX_ENA |
 				EP5_RX_ENA | EP6_RX_ENA | EP7_RX_ENA);
 	SSYNC();
+}
+
+int __init musb_platform_init(struct musb *musb, void *board_data)
+{
+
+	/*
+	 * Rev 1.0 BF549 EZ-KITs require PE7 to be high for both DEVICE
+	 * and OTG HOST modes, while rev 1.1 and greater require PE7 to
+	 * be low for DEVICE mode and high for HOST mode. We set it high
+	 * here because we are in host mode
+	 */
+
+	if (gpio_request(musb->config->gpio_vrsel, "USB_VRSEL")) {
+		printk(KERN_ERR "Failed ro request USB_VRSEL GPIO_%d\n",
+			musb->config->gpio_vrsel);
+		return -ENODEV;
+	}
+	gpio_direction_output(musb->config->gpio_vrsel, 0);
+
+	usb_nop_xceiv_register();
+	musb->xceiv = otg_get_transceiver();
+	if (!musb->xceiv) {
+		gpio_free(musb->config->gpio_vrsel);
+		return -ENODEV;
+	}
+
+	musb_platform_reg_init(musb);
 
 	if (is_host_enabled(musb)) {
 		musb->board_set_vbus = bfin_set_vbus;
@@ -394,6 +401,27 @@
 	return 0;
 }
 
+#ifdef CONFIG_PM
+void musb_platform_save_context(struct musb *musb,
+			struct musb_context_registers *musb_context)
+{
+	if (is_host_active(musb))
+		/*
+		 * During hibernate gpio_vrsel will change from high to low
+		 * low which will generate wakeup event resume the system
+		 * immediately.  Set it to 0 before hibernate to avoid this
+		 * wakeup event.
+		 */
+		gpio_set_value(musb->config->gpio_vrsel, 0);
+}
+
+void musb_platform_restore_context(struct musb *musb,
+			struct musb_context_registers *musb_context)
+{
+	musb_platform_reg_init(musb);
+}
+#endif
+
 int musb_platform_exit(struct musb *musb)
 {
 	gpio_free(musb->config->gpio_vrsel);
diff --git a/drivers/usb/musb/musb_core.c b/drivers/usb/musb/musb_core.c
index c9f9024..e6669fc 100644
--- a/drivers/usb/musb/musb_core.c
+++ b/drivers/usb/musb/musb_core.c
@@ -552,7 +552,8 @@
 	if (int_usb & MUSB_INTR_SESSREQ) {
 		void __iomem *mbase = musb->mregs;
 
-		if (devctl & MUSB_DEVCTL_BDEVICE) {
+		if ((devctl & MUSB_DEVCTL_VBUS) == MUSB_DEVCTL_VBUS
+				&& (devctl & MUSB_DEVCTL_BDEVICE)) {
 			DBG(3, "SessReq while on B state\n");
 			return IRQ_HANDLED;
 		}
@@ -1052,6 +1053,11 @@
 		clk_put(musb->clock);
 	spin_unlock_irqrestore(&musb->lock, flags);
 
+	if (!is_otg_enabled(musb) && is_host_enabled(musb))
+		usb_remove_hcd(musb_to_hcd(musb));
+	musb_writeb(musb->mregs, MUSB_DEVCTL, 0);
+	musb_platform_exit(musb);
+
 	/* FIXME power down */
 }
 
@@ -2244,13 +2250,6 @@
 	 */
 	musb_exit_debugfs(musb);
 	musb_shutdown(pdev);
-#ifdef CONFIG_USB_MUSB_HDRC_HCD
-	if (musb->board_mode == MUSB_HOST)
-		usb_remove_hcd(musb_to_hcd(musb));
-#endif
-	musb_writeb(musb->mregs, MUSB_DEVCTL, 0);
-	musb_platform_exit(musb);
-	musb_writeb(musb->mregs, MUSB_DEVCTL, 0);
 
 	musb_free(musb);
 	iounmap(ctrl_base);
@@ -2411,9 +2410,6 @@
 	unsigned long	flags;
 	struct musb	*musb = dev_to_musb(&pdev->dev);
 
-	if (!musb->clock)
-		return 0;
-
 	spin_lock_irqsave(&musb->lock, flags);
 
 	if (is_peripheral_active(musb)) {
@@ -2428,10 +2424,12 @@
 
 	musb_save_context(musb);
 
-	if (musb->set_clock)
-		musb->set_clock(musb->clock, 0);
-	else
-		clk_disable(musb->clock);
+	if (musb->clock) {
+		if (musb->set_clock)
+			musb->set_clock(musb->clock, 0);
+		else
+			clk_disable(musb->clock);
+	}
 	spin_unlock_irqrestore(&musb->lock, flags);
 	return 0;
 }
@@ -2441,13 +2439,12 @@
 	struct platform_device *pdev = to_platform_device(dev);
 	struct musb	*musb = dev_to_musb(&pdev->dev);
 
-	if (!musb->clock)
-		return 0;
-
-	if (musb->set_clock)
-		musb->set_clock(musb->clock, 1);
-	else
-		clk_enable(musb->clock);
+	if (musb->clock) {
+		if (musb->set_clock)
+			musb->set_clock(musb->clock, 1);
+		else
+			clk_enable(musb->clock);
+	}
 
 	musb_restore_context(musb);
 
diff --git a/drivers/usb/musb/musb_core.h b/drivers/usb/musb/musb_core.h
index 69797e5..febaabc 100644
--- a/drivers/usb/musb/musb_core.h
+++ b/drivers/usb/musb/musb_core.h
@@ -487,7 +487,7 @@
 };
 
 #if defined(CONFIG_ARCH_OMAP2430) || defined(CONFIG_ARCH_OMAP3) || \
-    defined(CONFIG_ARCH_OMAP4)
+    defined(CONFIG_ARCH_OMAP4) || defined(CONFIG_BLACKFIN)
 extern void musb_platform_save_context(struct musb *musb,
 		struct musb_context_registers *musb_context);
 extern void musb_platform_restore_context(struct musb *musb,
diff --git a/drivers/usb/musb/musb_gadget.c b/drivers/usb/musb/musb_gadget.c
index 5d81504..36cfd06 100644
--- a/drivers/usb/musb/musb_gadget.c
+++ b/drivers/usb/musb/musb_gadget.c
@@ -644,10 +644,8 @@
 	 */
 
 				csr |= MUSB_RXCSR_DMAENAB;
-				if (!musb_ep->hb_mult &&
-					musb_ep->hw_ep->rx_double_buffered)
-					csr |= MUSB_RXCSR_AUTOCLEAR;
 #ifdef USE_MODE1
+				csr |= MUSB_RXCSR_AUTOCLEAR;
 				/* csr |= MUSB_RXCSR_DMAMODE; */
 
 				/* this special sequence (enabling and then
@@ -656,6 +654,10 @@
 				 */
 				musb_writew(epio, MUSB_RXCSR,
 					csr | MUSB_RXCSR_DMAMODE);
+#else
+				if (!musb_ep->hb_mult &&
+					musb_ep->hw_ep->rx_double_buffered)
+					csr |= MUSB_RXCSR_AUTOCLEAR;
 #endif
 				musb_writew(epio, MUSB_RXCSR, csr);
 
@@ -807,7 +809,7 @@
 
 #if defined(CONFIG_USB_INVENTRA_DMA) || defined(CONFIG_USB_TUSB_OMAP_DMA)
 		/* Autoclear doesn't clear RxPktRdy for short packets */
-		if ((dma->desired_mode == 0)
+		if ((dma->desired_mode == 0 && !hw_ep->rx_double_buffered)
 				|| (dma->actual_len
 					& (musb_ep->packet_sz - 1))) {
 			/* ack the read! */
@@ -818,8 +820,16 @@
 		/* incomplete, and not short? wait for next IN packet */
 		if ((request->actual < request->length)
 				&& (musb_ep->dma->actual_len
-					== musb_ep->packet_sz))
+					== musb_ep->packet_sz)) {
+			/* In double buffer case, continue to unload fifo if
+ 			 * there is Rx packet in FIFO.
+ 			 **/
+			csr = musb_readw(epio, MUSB_RXCSR);
+			if ((csr & MUSB_RXCSR_RXPKTRDY) &&
+				hw_ep->rx_double_buffered)
+				goto exit;
 			return;
+		}
 #endif
 		musb_g_giveback(musb_ep, request, 0);
 
@@ -827,7 +837,7 @@
 		if (!request)
 			return;
 	}
-
+exit:
 	/* Analyze request */
 	rxstate(musb, to_musb_request(request));
 }
@@ -916,13 +926,9 @@
 		 * likewise high bandwidth periodic tx
 		 */
 		/* Set TXMAXP with the FIFO size of the endpoint
-		 * to disable double buffering mode. Currently, It seems that double
-		 * buffering has problem if musb RTL revision number < 2.0.
+		 * to disable double buffering mode.
 		 */
-		if (musb->hwvers < MUSB_HWVERS_2000)
-			musb_writew(regs, MUSB_TXMAXP, hw_ep->max_packet_sz_tx);
-		else
-			musb_writew(regs, MUSB_TXMAXP, musb_ep->packet_sz | (musb_ep->hb_mult << 11));
+		musb_writew(regs, MUSB_TXMAXP, musb_ep->packet_sz | (musb_ep->hb_mult << 11));
 
 		csr = MUSB_TXCSR_MODE | MUSB_TXCSR_CLRDATATOG;
 		if (musb_readw(regs, MUSB_TXCSR)
@@ -958,10 +964,7 @@
 		/* Set RXMAXP with the FIFO size of the endpoint
 		 * to disable double buffering mode.
 		 */
-		if (musb->hwvers < MUSB_HWVERS_2000)
-			musb_writew(regs, MUSB_RXMAXP, hw_ep->max_packet_sz_rx);
-		else
-			musb_writew(regs, MUSB_RXMAXP, musb_ep->packet_sz | (musb_ep->hb_mult << 11));
+		musb_writew(regs, MUSB_RXMAXP, musb_ep->packet_sz | (musb_ep->hb_mult << 11));
 
 		/* force shared fifo to OUT-only mode */
 		if (hw_ep->is_shared_fifo) {
@@ -1166,8 +1169,6 @@
 						: DMA_FROM_DEVICE);
 			request->mapped = 0;
 		}
-	} else if (!req->buf) {
-		return -ENODATA;
 	} else
 		request->mapped = 0;
 
@@ -1695,8 +1696,10 @@
 	musb_platform_try_idle(musb, 0);
 
 	status = device_register(&musb->g.dev);
-	if (status != 0)
+	if (status != 0) {
+		put_device(&musb->g.dev);
 		the_gadget = NULL;
+	}
 	return status;
 }
 
diff --git a/drivers/usb/musb/musb_regs.h b/drivers/usb/musb/musb_regs.h
index 2442675..5a727c5 100644
--- a/drivers/usb/musb/musb_regs.h
+++ b/drivers/usb/musb/musb_regs.h
@@ -633,8 +633,9 @@
 	return 0;
 }
 
-static inline void  musb_read_txhubport(void __iomem *mbase, u8 epnum)
+static inline u8 musb_read_txhubport(void __iomem *mbase, u8 epnum)
 {
+	return 0;
 }
 
 #endif /* CONFIG_BLACKFIN */
diff --git a/drivers/usb/musb/musbhsdma.c b/drivers/usb/musb/musbhsdma.c
index 6f771af..563114d 100644
--- a/drivers/usb/musb/musbhsdma.c
+++ b/drivers/usb/musb/musbhsdma.c
@@ -158,6 +158,8 @@
 				dma_addr_t dma_addr, u32 len)
 {
 	struct musb_dma_channel *musb_channel = channel->private_data;
+	struct musb_dma_controller *controller = musb_channel->controller;
+	struct musb *musb = controller->private_data;
 
 	DBG(2, "ep%d-%s pkt_sz %d, dma_addr 0x%x length %d, mode %d\n",
 		musb_channel->epnum,
@@ -167,6 +169,18 @@
 	BUG_ON(channel->status == MUSB_DMA_STATUS_UNKNOWN ||
 		channel->status == MUSB_DMA_STATUS_BUSY);
 
+	/*
+	 * The DMA engine in RTL1.8 and above cannot handle
+	 * DMA addresses that are not aligned to a 4 byte boundary.
+	 * It ends up masking the last two bits of the address
+	 * programmed in DMA_ADDR.
+	 *
+	 * Fail such DMA transfers, so that the backup PIO mode
+	 * can carry out the transfer
+	 */
+	if ((musb->hwvers >= MUSB_HWVERS_1800) && (dma_addr % 4))
+		return false;
+
 	channel->actual_len = 0;
 	musb_channel->start_addr = dma_addr;
 	musb_channel->len = len;
diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c
index 89a9a58..76f8b35 100644
--- a/drivers/usb/serial/ftdi_sio.c
+++ b/drivers/usb/serial/ftdi_sio.c
@@ -794,6 +794,8 @@
 	{ USB_DEVICE(FTDI_VID, FTDI_SCIENCESCOPE_LOGBOOKML_PID) },
 	{ USB_DEVICE(FTDI_VID, FTDI_SCIENCESCOPE_LS_LOGBOOK_PID) },
 	{ USB_DEVICE(FTDI_VID, FTDI_SCIENCESCOPE_HS_LOGBOOK_PID) },
+	{ USB_DEVICE(QIHARDWARE_VID, MILKYMISTONE_JTAGSERIAL_PID),
+		.driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
 	{ },					/* Optional parameter entry */
 	{ }					/* Terminating entry */
 };
diff --git a/drivers/usb/serial/ftdi_sio_ids.h b/drivers/usb/serial/ftdi_sio_ids.h
index 7dfe02f1..263f625 100644
--- a/drivers/usb/serial/ftdi_sio_ids.h
+++ b/drivers/usb/serial/ftdi_sio_ids.h
@@ -1100,3 +1100,10 @@
 #define FTDI_SCIENCESCOPE_LOGBOOKML_PID		0xFF18
 #define FTDI_SCIENCESCOPE_LS_LOGBOOK_PID	0xFF1C
 #define FTDI_SCIENCESCOPE_HS_LOGBOOK_PID	0xFF1D
+
+/*
+ * Milkymist One JTAG/Serial
+ */
+#define QIHARDWARE_VID			0x20B7
+#define MILKYMISTONE_JTAGSERIAL_PID	0x0713
+
diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
index 2297fb1..ef2977d 100644
--- a/drivers/usb/serial/option.c
+++ b/drivers/usb/serial/option.c
@@ -518,7 +518,7 @@
 	{ USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_K4505, 0xff, 0xff, 0xff) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_K3765, 0xff, 0xff, 0xff) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_ETS1220, 0xff, 0xff, 0xff) },
-	{ USB_DEVICE(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_E14AC) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_E14AC, 0xff, 0xff, 0xff) },
 	{ USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_V640) },
 	{ USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_V620) },
 	{ USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_V740) },
diff --git a/drivers/uwb/allocator.c b/drivers/uwb/allocator.c
index 436e4f7..e45e673 100644
--- a/drivers/uwb/allocator.c
+++ b/drivers/uwb/allocator.c
@@ -326,7 +326,8 @@
 	int bit_index;
 
 	ai = kzalloc(sizeof(struct uwb_rsv_alloc_info), GFP_KERNEL);
-	
+	if (!ai)
+		return UWB_RSV_ALLOC_NOT_FOUND;
 	ai->min_mas = rsv->min_mas;
 	ai->max_mas = rsv->max_mas;
 	ai->max_interval = rsv->max_interval;
diff --git a/include/linux/usb.h b/include/linux/usb.h
index 35fe6ab..24300d8 100644
--- a/include/linux/usb.h
+++ b/include/linux/usb.h
@@ -797,7 +797,7 @@
  * @disconnect: Called when the interface is no longer accessible, usually
  *	because its device has been (or is being) disconnected or the
  *	driver module is being unloaded.
- * @ioctl: Used for drivers that want to talk to userspace through
+ * @unlocked_ioctl: Used for drivers that want to talk to userspace through
  *	the "usbfs" filesystem.  This lets devices provide ways to
  *	expose information to user space regardless of where they
  *	do (or don't) show up otherwise in the filesystem.
diff --git a/include/linux/usb/musb.h b/include/linux/usb/musb.h
index ee2dd1d..2387f9f 100644
--- a/include/linux/usb/musb.h
+++ b/include/linux/usb/musb.h
@@ -89,6 +89,8 @@
 	/* A GPIO controlling VRSEL in Blackfin */
 	unsigned int	gpio_vrsel;
 	unsigned int	gpio_vrsel_active;
+	/* musb CLKIN in Blackfin in MHZ */
+	unsigned char   clkin;
 #endif
 
 };