spi: rspi: Add more QSPI register documentation
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
diff --git a/drivers/spi/spi-rspi.c b/drivers/spi/spi-rspi.c
index 1f69343..4a2c759 100644
--- a/drivers/spi/spi-rspi.c
+++ b/drivers/spi/spi-rspi.c
@@ -62,12 +62,12 @@
#define RSPI_SPBFDR 0x22 /* Buffer Data Count Setting Register */
/*qspi only */
-#define QSPI_SPBFCR 0x18
-#define QSPI_SPBDCR 0x1a
-#define QSPI_SPBMUL0 0x1c
-#define QSPI_SPBMUL1 0x20
-#define QSPI_SPBMUL2 0x24
-#define QSPI_SPBMUL3 0x28
+#define QSPI_SPBFCR 0x18 /* Buffer Control Register */
+#define QSPI_SPBDCR 0x1a /* Buffer Data Count Register */
+#define QSPI_SPBMUL0 0x1c /* Transfer Data Length Multiplier Setting Register 0 */
+#define QSPI_SPBMUL1 0x20 /* Transfer Data Length Multiplier Setting Register 1 */
+#define QSPI_SPBMUL2 0x24 /* Transfer Data Length Multiplier Setting Register 2 */
+#define QSPI_SPBMUL3 0x28 /* Transfer Data Length Multiplier Setting Register 3 */
/* SPCR - Control Register */
#define SPCR_SPRIE 0x80 /* Receive Interrupt Enable */
@@ -79,6 +79,9 @@
/* RSPI on SH only */
#define SPCR_TXMD 0x02 /* TX Only Mode (vs. Full Duplex) */
#define SPCR_SPMS 0x01 /* 3-wire Mode (vs. 4-wire) */
+/* QSPI on R-Car M2 only */
+#define SPCR_WSWAP 0x02 /* Word Swap of read-data for DMAC */
+#define SPCR_BSWAP 0x01 /* Byte Swap of read-data for DMAC */
/* SSLP - Slave Select Polarity Register */
#define SSLP_SSL1P 0x02 /* SSL1 Signal Polarity Setting */
@@ -91,6 +94,9 @@
#define SPPCR_SPLP2 0x02 /* Loopback Mode 2 (non-inverting) */
#define SPPCR_SPLP 0x01 /* Loopback Mode (inverting) */
+#define SPPCR_IO3FV 0x04 /* Single-/Dual-SPI Mode IO3 Output Fixed Value */
+#define SPPCR_IO2FV 0x04 /* Single-/Dual-SPI Mode IO2 Output Fixed Value */
+
/* SPSR - Status Register */
#define SPSR_SPRF 0x80 /* Receive Buffer Full Flag */
#define SPSR_TEND 0x40 /* Transmit End */
@@ -151,6 +157,13 @@
#define SPCMD_SPB_24BIT 0x0100
#define SPCMD_SPB_32BIT 0x0200
#define SPCMD_SSLKP 0x0080 /* SSL Signal Level Keeping */
+#define SPCMD_SPIMOD_MASK 0x0060 /* SPI Operating Mode (QSPI only) */
+#define SPCMD_SPIMOD1 0x0040
+#define SPCMD_SPIMOD0 0x0020
+#define SPCMD_SPIMOD_SINGLE 0
+#define SPCMD_SPIMOD_DUAL SPCMD_SPIMOD0
+#define SPCMD_SPIMOD_QUAD SPCMD_SPIMOD1
+#define SPCMD_SPRW 0x0010 /* SPI Read/Write Access (Dual/Quad) */
#define SPCMD_SSLA_MASK 0x0030 /* SSL Assert Signal Setting (RSPI) */
#define SPCMD_BRDV_MASK 0x000c /* Bit Rate Division Setting */
#define SPCMD_CPOL 0x0002 /* Clock Polarity Setting */