mac80211: fix do_stop handling while suspended
When a device is unplugged while suspended, mac80211 is
de-initialized and all interfaces are removed while no
state is actually present in the driver. This can cause
warnings and driver confusion.
Fix this by reordering the do_stop code to not call the
driver when it is suspended, i.e. when there's no state
in the driver anyway.
The previous patches removed a few corner cases in ROC
and virtual monitor interfaces so that now this is safe
to do and no state should be left over.
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
diff --git a/net/mac80211/iface.c b/net/mac80211/iface.c
index d0d5f20..8c94195 100644
--- a/net/mac80211/iface.c
+++ b/net/mac80211/iface.c
@@ -739,8 +739,6 @@
sdata->dev->addr_len);
spin_unlock_bh(&local->filter_lock);
netif_addr_unlock_bh(sdata->dev);
-
- ieee80211_configure_filter(local);
}
del_timer_sync(&local->dynamic_ps_timer);
@@ -751,6 +749,7 @@
cancel_delayed_work_sync(&sdata->dfs_cac_timer_work);
if (sdata->wdev.cac_started) {
+ WARN_ON(local->suspended);
mutex_lock(&local->iflist_mtx);
ieee80211_vif_release_channel(sdata);
mutex_unlock(&local->iflist_mtx);
@@ -801,14 +800,9 @@
if (local->monitors == 0) {
local->hw.conf.flags &= ~IEEE80211_CONF_MONITOR;
hw_reconf_flags |= IEEE80211_CONF_CHANGE_MONITOR;
- ieee80211_del_virtual_monitor(local);
}
ieee80211_adjust_monitor_flags(sdata, -1);
- ieee80211_configure_filter(local);
- mutex_lock(&local->mtx);
- ieee80211_recalc_idle(local);
- mutex_unlock(&local->mtx);
break;
case NL80211_IFTYPE_P2P_DEVICE:
/* relies on synchronize_rcu() below */
@@ -838,27 +832,10 @@
/* fall through */
case NL80211_IFTYPE_AP:
skb_queue_purge(&sdata->skb_queue);
-
- if (going_down)
- drv_remove_interface(local, sdata);
}
sdata->bss = NULL;
- ieee80211_recalc_ps(local, -1);
-
- if (local->open_count == 0) {
- ieee80211_clear_tx_pending(local);
- ieee80211_stop_device(local);
-
- /* no reconfiguring after stop! */
- hw_reconf_flags = 0;
- }
-
- /* do after stop to avoid reconfiguring when we stop anyway */
- if (hw_reconf_flags)
- ieee80211_hw_config(local, hw_reconf_flags);
-
spin_lock_irqsave(&local->queue_stop_reason_lock, flags);
for (i = 0; i < IEEE80211_MAX_QUEUES; i++) {
skb_queue_walk_safe(&local->pending[i], skb, tmp) {
@@ -871,7 +848,54 @@
}
spin_unlock_irqrestore(&local->queue_stop_reason_lock, flags);
- if (local->monitors == local->open_count && local->monitors > 0)
+ if (local->open_count == 0)
+ ieee80211_clear_tx_pending(local);
+
+ /*
+ * If the interface goes down while suspended, presumably because
+ * the device was unplugged and that happens before our resume,
+ * then the driver is already unconfigured and the remainder of
+ * this function isn't needed.
+ * XXX: what about WoWLAN? If the device has software state, e.g.
+ * memory allocated, it might expect teardown commands from
+ * mac80211 here?
+ */
+ if (local->suspended) {
+ WARN_ON(local->wowlan);
+ WARN_ON(rtnl_dereference(local->monitor_sdata));
+ return;
+ }
+
+ switch (sdata->vif.type) {
+ case NL80211_IFTYPE_AP_VLAN:
+ break;
+ case NL80211_IFTYPE_MONITOR:
+ if (local->monitors == 0)
+ ieee80211_del_virtual_monitor(local);
+
+ mutex_lock(&local->mtx);
+ ieee80211_recalc_idle(local);
+ mutex_unlock(&local->mtx);
+ break;
+ default:
+ if (going_down)
+ drv_remove_interface(local, sdata);
+ }
+
+ ieee80211_recalc_ps(local, -1);
+
+ if (local->open_count == 0) {
+ ieee80211_stop_device(local);
+
+ /* no reconfiguring after stop! */
+ return;
+ }
+
+ /* do after stop to avoid reconfiguring when we stop anyway */
+ ieee80211_configure_filter(local);
+ ieee80211_hw_config(local, hw_reconf_flags);
+
+ if (local->monitors == local->open_count)
ieee80211_add_virtual_monitor(local);
}