ath5k: fix setup for CAB queue
The beacon sent gating doesn't seem to work with any combination
of flags. Thus, buffered frames tend to stay buffered forever,
using up tx descriptors.
Instead, use the DBA gating and hold transmission of the buffered
frames until 80% of the beacon interval has elapsed using the ready
time. This fixes the following error in AP mode:
ath5k phy0: no further txbuf available, dropping packet
Add a comment to acknowledge that this isn't the best solution.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/drivers/net/wireless/ath/ath5k/ath5k.h b/drivers/net/wireless/ath/ath5k/ath5k.h
index 66bcb50..ad4d446f 100644
--- a/drivers/net/wireless/ath/ath5k/ath5k.h
+++ b/drivers/net/wireless/ath/ath5k/ath5k.h
@@ -535,7 +535,7 @@
u32 tqi_cbr_period; /* Constant bit rate period */
u32 tqi_cbr_overflow_limit;
u32 tqi_burst_time;
- u32 tqi_ready_time; /* Not used */
+ u32 tqi_ready_time; /* Time queue waits after an event */
};
/*
diff --git a/drivers/net/wireless/ath/ath5k/base.c b/drivers/net/wireless/ath/ath5k/base.c
index b501537..535a6af 100644
--- a/drivers/net/wireless/ath/ath5k/base.c
+++ b/drivers/net/wireless/ath/ath5k/base.c
@@ -1516,7 +1516,8 @@
ret = ath5k_hw_get_tx_queueprops(ah, sc->bhalq, &qi);
if (ret)
- return ret;
+ goto err;
+
if (sc->opmode == NL80211_IFTYPE_AP ||
sc->opmode == NL80211_IFTYPE_MESH_POINT) {
/*
@@ -1543,10 +1544,25 @@
if (ret) {
ATH5K_ERR(sc, "%s: unable to update parameters for beacon "
"hardware queue!\n", __func__);
- return ret;
+ goto err;
}
+ ret = ath5k_hw_reset_tx_queue(ah, sc->bhalq); /* push to h/w */
+ if (ret)
+ goto err;
- return ath5k_hw_reset_tx_queue(ah, sc->bhalq); /* push to h/w */;
+ /* reconfigure cabq with ready time to 80% of beacon_interval */
+ ret = ath5k_hw_get_tx_queueprops(ah, AR5K_TX_QUEUE_ID_CAB, &qi);
+ if (ret)
+ goto err;
+
+ qi.tqi_ready_time = (sc->bintval * 80) / 100;
+ ret = ath5k_hw_set_tx_queueprops(ah, AR5K_TX_QUEUE_ID_CAB, &qi);
+ if (ret)
+ goto err;
+
+ ret = ath5k_hw_reset_tx_queue(ah, AR5K_TX_QUEUE_ID_CAB);
+err:
+ return ret;
}
static void
diff --git a/drivers/net/wireless/ath/ath5k/qcu.c b/drivers/net/wireless/ath/ath5k/qcu.c
index abe36c0..9122a85 100644
--- a/drivers/net/wireless/ath/ath5k/qcu.c
+++ b/drivers/net/wireless/ath/ath5k/qcu.c
@@ -408,12 +408,13 @@
break;
case AR5K_TX_QUEUE_CAB:
+ /* XXX: use BCN_SENT_GT, if we can figure out how */
AR5K_REG_ENABLE_BITS(ah, AR5K_QUEUE_MISC(queue),
- AR5K_QCU_MISC_FRSHED_BCN_SENT_GT |
+ AR5K_QCU_MISC_FRSHED_DBA_GT |
AR5K_QCU_MISC_CBREXP_DIS |
AR5K_QCU_MISC_CBREXP_BCN_DIS);
- ath5k_hw_reg_write(ah, ((AR5K_TUNE_BEACON_INTERVAL -
+ ath5k_hw_reg_write(ah, ((tq->tqi_ready_time -
(AR5K_TUNE_SW_BEACON_RESP -
AR5K_TUNE_DMA_BEACON_RESP) -
AR5K_TUNE_ADDITIONAL_SWBA_BACKOFF) * 1024) |