diff --git a/MAINTAINERS b/MAINTAINERS
index fbe0dca..57c07c2 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -457,7 +457,7 @@
 
 ARM/HP JORNADA 7XX MACHINE SUPPORT
 P:      Kristoffer Ericson
-M:      kristoffer_e1@hotmail.com
+M:      kristoffer.ericson@gmail.com
 W:      www.jlime.com
 S:      Maintained
 
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index a44c6da..8501631 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -324,6 +324,12 @@
 
 	  <http://www.digi.com/products/microprocessors/index.jsp>
 
+config ARCH_MXC
+	bool "Freescale MXC/iMX-based"
+	select ARCH_MTD_XIP
+	help
+	  Support for Freescale MXC/iMX-based family of processors
+
 config ARCH_PNX4008
 	bool "Philips Nexperia PNX4008 Mobile"
 	help
@@ -432,6 +438,7 @@
 source "arch/arm/mach-omap2/Kconfig"
 
 source "arch/arm/plat-s3c24xx/Kconfig"
+source "arch/arm/plat-s3c/Kconfig"
 
 if ARCH_S3C2410
 source "arch/arm/mach-s3c2400/Kconfig"
@@ -456,6 +463,8 @@
 
 source "arch/arm/mach-at91/Kconfig"
 
+source "arch/arm/plat-mxc/Kconfig"
+
 source "arch/arm/mach-netx/Kconfig"
 
 source "arch/arm/mach-ns9xxx/Kconfig"
diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index 40c5eb1..18101f5 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -82,24 +82,24 @@
 	  output to the second serial port on these devices.  Saying N will
 	  cause the debug messages to appear on the first serial port.
 
-config DEBUG_S3C2410_PORT
-	depends on DEBUG_LL && ARCH_S3C2410
-	bool "Kernel low-level debugging messages via S3C2410 UART"
+config DEBUG_S3C_PORT
+	depends on DEBUG_LL && PLAT_S3C
+	bool "Kernel low-level debugging messages via S3C UART"
 	help
 	  Say Y here if you want debug print routines to go to one of the
-	  S3C2410 internal UARTs. The chosen UART must have been configured
+	  S3C internal UARTs. The chosen UART must have been configured
 	  before it is used.
 
-config DEBUG_S3C2410_UART
-	depends on ARCH_S3C2410
-	int "S3C2410 UART to use for low-level debug"
+config DEBUG_S3C_UART
+	depends on PLAT_S3C
+	int "S3C UART to use for low-level debug"
 	default "0"
 	help
-	  Choice for UART for kernel low-level using S3C2410 UARTS,
+	  Choice for UART for kernel low-level using S3C UARTS,
 	  should be between zero and two. The port must have been
 	  initialised by the boot-loader before use.
 
 	  The uncompressor code port configuration is now handled
-	  by CONFIG_S3C2410_LOWLEVEL_UART_PORT.
+	  by CONFIG_S3C_LOWLEVEL_UART_PORT.
 
 endmenu
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index cbd5010..fa4ea9f 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -137,6 +137,8 @@
  textofs-$(CONFIG_ARCH_NS9XXX)	   := 0x00108000
  machine-$(CONFIG_ARCH_DAVINCI)	   := davinci
  machine-$(CONFIG_ARCH_KS8695)     := ks8695
+  incdir-$(CONFIG_ARCH_MXC)	   := mxc
+ machine-$(CONFIG_ARCH_MX3)	   := mx3
 
 ifeq ($(CONFIG_ARCH_EBSA110),y)
 # This is what happens if you forget the IOCS16 line.
@@ -183,6 +185,7 @@
 core-$(CONFIG_PLAT_IOP)		+= arch/arm/plat-iop/
 core-$(CONFIG_ARCH_OMAP)	+= arch/arm/plat-omap/
 core-$(CONFIG_PLAT_S3C24XX)		+= arch/arm/plat-s3c24xx/
+core-$(CONFIG_ARCH_MXC)		+= arch/arm/plat-mxc/
 
 drivers-$(CONFIG_OPROFILE)      += arch/arm/oprofile/
 drivers-$(CONFIG_ARCH_CLPS7500)	+= drivers/acorn/char/
diff --git a/arch/arm/boot/Makefile b/arch/arm/boot/Makefile
index ec9c400c..25f1230 100644
--- a/arch/arm/boot/Makefile
+++ b/arch/arm/boot/Makefile
@@ -91,4 +91,12 @@
 	$(CONFIG_SHELL) $(srctree)/$(src)/install.sh $(KERNELRELEASE) \
 	$(obj)/zImage System.map "$(INSTALL_PATH)"
 
+zi:
+	$(CONFIG_SHELL) $(srctree)/$(src)/install.sh $(KERNELRELEASE) \
+	$(obj)/zImage System.map "$(INSTALL_PATH)"
+
+i:
+	$(CONFIG_SHELL) $(srctree)/$(src)/install.sh $(KERNELRELEASE) \
+	$(obj)/Image System.map "$(INSTALL_PATH)"
+
 subdir-	    := bootp compressed
diff --git a/arch/arm/boot/compressed/Makefile b/arch/arm/boot/compressed/Makefile
index a1f1691..6b8cbd6 100644
--- a/arch/arm/boot/compressed/Makefile
+++ b/arch/arm/boot/compressed/Makefile
@@ -73,7 +73,7 @@
 
 targets       := vmlinux vmlinux.lds piggy.gz piggy.o font.o font.c \
 		 head.o misc.o $(OBJS)
-EXTRA_CFLAGS  := -fpic
+EXTRA_CFLAGS  := -fpic -fno-builtin
 EXTRA_AFLAGS  :=
 
 # Supply ZRELADDR, INITRD_PHYS and PARAMS_PHYS to the decompressor via
diff --git a/arch/arm/boot/compressed/head.S b/arch/arm/boot/compressed/head.S
index d7fb5ee1..b9b03ed 100644
--- a/arch/arm/boot/compressed/head.S
+++ b/arch/arm/boot/compressed/head.S
@@ -55,7 +55,7 @@
 #elif defined(CONFIG_ARCH_S3C2410)
 		.macro loadsp, rb
 		mov	\rb, #0x50000000
-		add	\rb, \rb, #0x4000 * CONFIG_S3C2410_LOWLEVEL_UART_PORT
+		add	\rb, \rb, #0x4000 * CONFIG_S3C_LOWLEVEL_UART_PORT
 		.endm
 #else
 		.macro	loadsp,	rb
diff --git a/arch/arm/configs/em_x270_defconfig b/arch/arm/configs/em_x270_defconfig
new file mode 100644
index 0000000..6bea090
--- /dev/null
+++ b/arch/arm/configs/em_x270_defconfig
@@ -0,0 +1,1265 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.22
+# Mon Jul  9 15:18:20 2007
+#
+CONFIG_ARM=y
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+CONFIG_GENERIC_GPIO=y
+CONFIG_GENERIC_TIME=y
+# CONFIG_GENERIC_CLOCKEVENTS is not set
+CONFIG_MMU=y
+# CONFIG_NO_IOPORT is not set
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_STACKTRACE_SUPPORT=y
+CONFIG_LOCKDEP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+# CONFIG_ARCH_HAS_ILOG2_U32 is not set
+# CONFIG_ARCH_HAS_ILOG2_U64 is not set
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_ZONE_DMA=y
+CONFIG_ARCH_MTD_XIP=y
+CONFIG_VECTORS_BASE=0xffff0000
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# Code maturity level options
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+
+#
+# General setup
+#
+CONFIG_LOCALVERSION="-em-x270"
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+# CONFIG_IPC_NS is not set
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_UTS_NS is not set
+# CONFIG_AUDIT is not set
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=17
+CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_RELAY is not set
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+CONFIG_UID16=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
+CONFIG_RT_MUTEXES=y
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+
+#
+# Loadable module support
+#
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_KMOD=y
+
+#
+# Block layer
+#
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+
+#
+# System Type
+#
+# CONFIG_ARCH_AAEC2000 is not set
+# CONFIG_ARCH_INTEGRATOR is not set
+# CONFIG_ARCH_REALVIEW is not set
+# CONFIG_ARCH_VERSATILE is not set
+# CONFIG_ARCH_AT91 is not set
+# CONFIG_ARCH_CLPS7500 is not set
+# CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_CO285 is not set
+# CONFIG_ARCH_EBSA110 is not set
+# CONFIG_ARCH_EP93XX is not set
+# CONFIG_ARCH_FOOTBRIDGE is not set
+# CONFIG_ARCH_NETX is not set
+# CONFIG_ARCH_H720X is not set
+# CONFIG_ARCH_IMX is not set
+# CONFIG_ARCH_IOP13XX is not set
+# CONFIG_ARCH_IOP32X is not set
+# CONFIG_ARCH_IOP33X is not set
+# CONFIG_ARCH_IXP23XX is not set
+# CONFIG_ARCH_IXP2000 is not set
+# CONFIG_ARCH_IXP4XX is not set
+# CONFIG_ARCH_L7200 is not set
+# CONFIG_ARCH_KS8695 is not set
+# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_PNX4008 is not set
+CONFIG_ARCH_PXA=y
+# CONFIG_ARCH_RPC is not set
+# CONFIG_ARCH_SA1100 is not set
+# CONFIG_ARCH_S3C2410 is not set
+# CONFIG_ARCH_SHARK is not set
+# CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_DAVINCI is not set
+# CONFIG_ARCH_OMAP is not set
+
+#
+# Intel PXA2xx Implementations
+#
+# CONFIG_ARCH_LUBBOCK is not set
+# CONFIG_MACH_LOGICPD_PXA270 is not set
+# CONFIG_MACH_MAINSTONE is not set
+# CONFIG_ARCH_PXA_IDP is not set
+# CONFIG_PXA_SHARPSL is not set
+# CONFIG_MACH_TRIZEPS4 is not set
+CONFIG_MACH_EM_X270=y
+CONFIG_PXA27x=y
+
+#
+# Processor Type
+#
+CONFIG_CPU_32=y
+CONFIG_CPU_XSCALE=y
+CONFIG_CPU_32v5=y
+CONFIG_CPU_ABRT_EV5T=y
+CONFIG_CPU_CACHE_VIVT=y
+CONFIG_CPU_TLB_V4WBI=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+
+#
+# Processor Features
+#
+CONFIG_ARM_THUMB=y
+# CONFIG_CPU_DCACHE_DISABLE is not set
+# CONFIG_OUTER_CACHE is not set
+CONFIG_IWMMXT=y
+CONFIG_XSCALE_PMU=y
+
+#
+# Bus support
+#
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+
+#
+# PCCARD (PCMCIA/CardBus) support
+#
+# CONFIG_PCCARD is not set
+
+#
+# Kernel Features
+#
+# CONFIG_TICK_ONESHOT is not set
+# CONFIG_PREEMPT is not set
+# CONFIG_NO_IDLE_HZ is not set
+CONFIG_HZ=100
+CONFIG_AEABI=y
+CONFIG_OABI_COMPAT=y
+# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4096
+# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=1
+CONFIG_ALIGNMENT_TRAP=y
+
+#
+# Boot options
+#
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE=""
+# CONFIG_XIP_KERNEL is not set
+# CONFIG_KEXEC is not set
+
+#
+# Floating point emulation
+#
+
+#
+# At least one emulation must be selected
+#
+CONFIG_FPE_NWFPE=y
+# CONFIG_FPE_NWFPE_XP is not set
+# CONFIG_FPE_FASTFPE is not set
+
+#
+# Userspace binary formats
+#
+CONFIG_BINFMT_ELF=y
+# CONFIG_BINFMT_AOUT is not set
+# CONFIG_BINFMT_MISC is not set
+
+#
+# Power management options
+#
+CONFIG_PM=y
+CONFIG_PM_LEGACY=y
+# CONFIG_PM_DEBUG is not set
+# CONFIG_PM_SYSFS_DEPRECATED is not set
+CONFIG_APM_EMULATION=m
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+CONFIG_XFRM=y
+# CONFIG_XFRM_USER is not set
+# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+# CONFIG_IP_MULTICAST is not set
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_ARPD is not set
+# CONFIG_SYN_COOKIES is not set
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_INET_XFRM_MODE_TRANSPORT=y
+CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_INET6_XFRM_TUNNEL is not set
+# CONFIG_INET6_TUNNEL is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+
+#
+# QoS and/or fair queueing
+#
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+CONFIG_BT=m
+CONFIG_BT_L2CAP=m
+CONFIG_BT_SCO=m
+CONFIG_BT_RFCOMM=m
+# CONFIG_BT_RFCOMM_TTY is not set
+CONFIG_BT_BNEP=m
+# CONFIG_BT_BNEP_MC_FILTER is not set
+# CONFIG_BT_BNEP_PROTO_FILTER is not set
+CONFIG_BT_HIDP=m
+
+#
+# Bluetooth device drivers
+#
+CONFIG_BT_HCIUSB=m
+# CONFIG_BT_HCIUSB_SCO is not set
+CONFIG_BT_HCIUART=m
+# CONFIG_BT_HCIUART_H4 is not set
+# CONFIG_BT_HCIUART_BCSP is not set
+CONFIG_BT_HCIBCM203X=m
+CONFIG_BT_HCIBPA10X=m
+CONFIG_BT_HCIBFUSB=m
+# CONFIG_BT_HCIVHCI is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
+CONFIG_IEEE80211=m
+# CONFIG_IEEE80211_DEBUG is not set
+CONFIG_IEEE80211_CRYPT_WEP=m
+CONFIG_IEEE80211_CRYPT_CCMP=m
+# CONFIG_IEEE80211_CRYPT_TKIP is not set
+# CONFIG_IEEE80211_SOFTMAC is not set
+# CONFIG_RFKILL is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+CONFIG_FW_LOADER=y
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+
+#
+# Connector - unified userspace <-> kernelspace linker
+#
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+CONFIG_MTD_CONCAT=y
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_REDBOOT_PARTS is not set
+# CONFIG_MTD_CMDLINE_PARTS is not set
+# CONFIG_MTD_AFS_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+# CONFIG_MTD_CFI is not set
+# CONFIG_MTD_JEDECPROBE is not set
+# CONFIG_MTD_CFI_NOSWAP is not set
+# CONFIG_MTD_CFI_BE_BYTE_SWAP is not set
+# CONFIG_MTD_CFI_LE_BYTE_SWAP is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_SHARP_SL is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+CONFIG_MTD_NAND=y
+# CONFIG_MTD_NAND_VERIFY_WRITE is not set
+# CONFIG_MTD_NAND_ECC_SMC is not set
+# CONFIG_MTD_NAND_MUSEUM_IDS is not set
+# CONFIG_MTD_NAND_H1900 is not set
+CONFIG_MTD_NAND_IDS=y
+# CONFIG_MTD_NAND_DISKONCHIP is not set
+# CONFIG_MTD_NAND_SHARPSL is not set
+# CONFIG_MTD_NAND_NANDSIM is not set
+CONFIG_MTD_NAND_PLATFORM=y
+# CONFIG_MTD_ONENAND is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
+
+#
+# Parallel port support
+#
+# CONFIG_PARPORT is not set
+
+#
+# Plug and Play support
+#
+# CONFIG_PNPACPI is not set
+
+#
+# Block devices
+#
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=y
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_UB is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=12000
+CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+CONFIG_SCSI=y
+# CONFIG_SCSI_TGT is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_SCSI_PROC_FS is not set
+
+#
+# SCSI support type (disk, tape, CD-ROM)
+#
+CONFIG_BLK_DEV_SD=y
+# CONFIG_CHR_DEV_ST is not set
+# CONFIG_CHR_DEV_OSST is not set
+# CONFIG_BLK_DEV_SR is not set
+# CONFIG_CHR_DEV_SG is not set
+# CONFIG_CHR_DEV_SCH is not set
+
+#
+# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
+#
+# CONFIG_SCSI_MULTI_LUN is not set
+# CONFIG_SCSI_CONSTANTS is not set
+# CONFIG_SCSI_LOGGING is not set
+# CONFIG_SCSI_SCAN_ASYNC is not set
+CONFIG_SCSI_WAIT_SCAN=m
+
+#
+# SCSI Transports
+#
+# CONFIG_SCSI_SPI_ATTRS is not set
+# CONFIG_SCSI_FC_ATTRS is not set
+# CONFIG_SCSI_ISCSI_ATTRS is not set
+# CONFIG_SCSI_SAS_ATTRS is not set
+# CONFIG_SCSI_SAS_LIBSAS is not set
+
+#
+# SCSI low-level drivers
+#
+# CONFIG_ISCSI_TCP is not set
+# CONFIG_SCSI_DEBUG is not set
+# CONFIG_ATA is not set
+
+#
+# Multi-device support (RAID and LVM)
+#
+# CONFIG_MD is not set
+
+#
+# Network device support
+#
+CONFIG_NETDEVICES=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_PHYLIB is not set
+
+#
+# Ethernet (10 or 100Mbit)
+#
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_SMC91X is not set
+CONFIG_DM9000=y
+# CONFIG_SMC911X is not set
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+
+#
+# USB Network Adapters
+#
+# CONFIG_USB_CATC is not set
+# CONFIG_USB_KAWETH is not set
+# CONFIG_USB_PEGASUS is not set
+# CONFIG_USB_RTL8150 is not set
+# CONFIG_USB_USBNET_MII is not set
+# CONFIG_USB_USBNET is not set
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+
+#
+# ISDN subsystem
+#
+# CONFIG_ISDN is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
+
+#
+# Userland interfaces
+#
+CONFIG_INPUT_MOUSEDEV=y
+# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
+CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_TSDEV is not set
+CONFIG_INPUT_EVDEV=y
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+CONFIG_INPUT_KEYBOARD=y
+# CONFIG_KEYBOARD_ATKBD is not set
+# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_KEYBOARD_LKKBD is not set
+# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_STOWAWAY is not set
+CONFIG_KEYBOARD_PXA27x=m
+# CONFIG_KEYBOARD_GPIO is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+# CONFIG_TOUCHSCREEN_GUNZE is not set
+# CONFIG_TOUCHSCREEN_ELO is not set
+# CONFIG_TOUCHSCREEN_MTOUCH is not set
+# CONFIG_TOUCHSCREEN_MK712 is not set
+# CONFIG_TOUCHSCREEN_PENMOUNT is not set
+# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set
+# CONFIG_TOUCHSCREEN_TOUCHWIN is not set
+# CONFIG_TOUCHSCREEN_UCB1400 is not set
+# CONFIG_TOUCHSCREEN_USB_COMPOSITE is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+CONFIG_SERIO=y
+# CONFIG_SERIO_SERPORT is not set
+CONFIG_SERIO_LIBPS2=y
+# CONFIG_SERIO_RAW is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+CONFIG_VT=y
+CONFIG_VT_CONSOLE=y
+CONFIG_HW_CONSOLE=y
+# CONFIG_VT_HW_CONSOLE_BINDING is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+CONFIG_SERIAL_PXA=y
+CONFIG_SERIAL_PXA_CONSOLE=y
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_UNIX98_PTYS=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+
+#
+# IPMI
+#
+# CONFIG_IPMI_HANDLER is not set
+# CONFIG_WATCHDOG is not set
+CONFIG_HW_RANDOM=m
+# CONFIG_NVRAM is not set
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+
+#
+# TPM devices
+#
+# CONFIG_TCG_TPM is not set
+# CONFIG_I2C is not set
+
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+
+#
+# Dallas's 1-wire bus
+#
+# CONFIG_W1 is not set
+# CONFIG_HWMON is not set
+
+#
+# Misc devices
+#
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_SM501 is not set
+
+#
+# LED devices
+#
+# CONFIG_NEW_LEDS is not set
+
+#
+# LED drivers
+#
+
+#
+# LED Triggers
+#
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+# CONFIG_DAB is not set
+
+#
+# Graphics support
+#
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+# CONFIG_VGASTATE is not set
+CONFIG_FB=y
+# CONFIG_FIRMWARE_EDID is not set
+# CONFIG_FB_DDC is not set
+CONFIG_FB_CFB_FILLRECT=y
+CONFIG_FB_CFB_COPYAREA=y
+CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_SYS_FOPS is not set
+CONFIG_FB_DEFERRED_IO=y
+# CONFIG_FB_SVGALIB is not set
+# CONFIG_FB_MACMODES is not set
+# CONFIG_FB_BACKLIGHT is not set
+# CONFIG_FB_MODE_HELPERS is not set
+# CONFIG_FB_TILEBLITTING is not set
+
+#
+# Frame buffer hardware drivers
+#
+# CONFIG_FB_S1D13XXX is not set
+CONFIG_FB_PXA=y
+# CONFIG_FB_PXA_PARAMETERS is not set
+# CONFIG_FB_MBX is not set
+# CONFIG_FB_VIRTUAL is not set
+
+#
+# Console display driver support
+#
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_DUMMY_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
+# CONFIG_FONTS is not set
+CONFIG_FONT_8x8=y
+CONFIG_FONT_8x16=y
+CONFIG_LOGO=y
+CONFIG_LOGO_LINUX_MONO=y
+CONFIG_LOGO_LINUX_VGA16=y
+CONFIG_LOGO_LINUX_CLUT224=y
+
+#
+# Sound
+#
+CONFIG_SOUND=m
+
+#
+# Advanced Linux Sound Architecture
+#
+CONFIG_SND=m
+CONFIG_SND_TIMER=m
+CONFIG_SND_PCM=m
+# CONFIG_SND_SEQUENCER is not set
+CONFIG_SND_OSSEMUL=y
+CONFIG_SND_MIXER_OSS=m
+CONFIG_SND_PCM_OSS=m
+CONFIG_SND_PCM_OSS_PLUGINS=y
+# CONFIG_SND_DYNAMIC_MINORS is not set
+CONFIG_SND_SUPPORT_OLD_API=y
+CONFIG_SND_VERBOSE_PROCFS=y
+# CONFIG_SND_VERBOSE_PRINTK is not set
+# CONFIG_SND_DEBUG is not set
+
+#
+# Generic devices
+#
+CONFIG_SND_AC97_CODEC=m
+# CONFIG_SND_DUMMY is not set
+# CONFIG_SND_MTPAV is not set
+# CONFIG_SND_SERIAL_U16550 is not set
+# CONFIG_SND_MPU401 is not set
+
+#
+# ALSA ARM devices
+#
+CONFIG_SND_PXA2XX_PCM=m
+CONFIG_SND_PXA2XX_AC97=m
+
+#
+# USB devices
+#
+# CONFIG_SND_USB_AUDIO is not set
+# CONFIG_SND_USB_CAIAQ is not set
+
+#
+# System on Chip audio support
+#
+# CONFIG_SND_SOC is not set
+
+#
+# Open Sound System
+#
+# CONFIG_SOUND_PRIME is not set
+CONFIG_AC97_BUS=m
+
+#
+# HID Devices
+#
+CONFIG_HID=y
+# CONFIG_HID_DEBUG is not set
+
+#
+# USB Input Devices
+#
+CONFIG_USB_HID=y
+# CONFIG_USB_HIDINPUT_POWERBOOK is not set
+# CONFIG_HID_FF is not set
+# CONFIG_USB_HIDDEV is not set
+
+#
+# USB support
+#
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+# CONFIG_USB_ARCH_HAS_EHCI is not set
+CONFIG_USB=y
+# CONFIG_USB_DEBUG is not set
+
+#
+# Miscellaneous USB options
+#
+CONFIG_USB_DEVICEFS=y
+# CONFIG_USB_DEVICE_CLASS is not set
+# CONFIG_USB_DYNAMIC_MINORS is not set
+# CONFIG_USB_SUSPEND is not set
+# CONFIG_USB_OTG is not set
+
+#
+# USB Host Controller Drivers
+#
+# CONFIG_USB_ISP116X_HCD is not set
+CONFIG_USB_OHCI_HCD=y
+# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
+# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
+CONFIG_USB_OHCI_LITTLE_ENDIAN=y
+# CONFIG_USB_SL811_HCD is not set
+
+#
+# USB Device Class drivers
+#
+# CONFIG_USB_ACM is not set
+# CONFIG_USB_PRINTER is not set
+
+#
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+#
+
+#
+# may also be needed; see USB_STORAGE Help for more information
+#
+CONFIG_USB_STORAGE=y
+# CONFIG_USB_STORAGE_DEBUG is not set
+# CONFIG_USB_STORAGE_DATAFAB is not set
+# CONFIG_USB_STORAGE_FREECOM is not set
+# CONFIG_USB_STORAGE_DPCM is not set
+# CONFIG_USB_STORAGE_USBAT is not set
+# CONFIG_USB_STORAGE_SDDR09 is not set
+# CONFIG_USB_STORAGE_SDDR55 is not set
+# CONFIG_USB_STORAGE_JUMPSHOT is not set
+# CONFIG_USB_STORAGE_ALAUDA is not set
+# CONFIG_USB_STORAGE_KARMA is not set
+# CONFIG_USB_LIBUSUAL is not set
+
+#
+# USB Imaging devices
+#
+# CONFIG_USB_MDC800 is not set
+# CONFIG_USB_MICROTEK is not set
+# CONFIG_USB_MON is not set
+
+#
+# USB port drivers
+#
+
+#
+# USB Serial Converter support
+#
+# CONFIG_USB_SERIAL is not set
+
+#
+# USB Miscellaneous drivers
+#
+# CONFIG_USB_EMI62 is not set
+# CONFIG_USB_EMI26 is not set
+# CONFIG_USB_ADUTUX is not set
+# CONFIG_USB_AUERSWALD is not set
+# CONFIG_USB_RIO500 is not set
+# CONFIG_USB_LEGOTOWER is not set
+# CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
+# CONFIG_USB_LED is not set
+# CONFIG_USB_CYPRESS_CY7C63 is not set
+# CONFIG_USB_CYTHERM is not set
+# CONFIG_USB_PHIDGET is not set
+# CONFIG_USB_IDMOUSE is not set
+# CONFIG_USB_FTDI_ELAN is not set
+# CONFIG_USB_APPLEDISPLAY is not set
+# CONFIG_USB_LD is not set
+# CONFIG_USB_TRANCEVIBRATOR is not set
+# CONFIG_USB_IOWARRIOR is not set
+# CONFIG_USB_TEST is not set
+
+#
+# USB DSL modem support
+#
+
+#
+# USB Gadget Support
+#
+# CONFIG_USB_GADGET is not set
+CONFIG_MMC=m
+# CONFIG_MMC_DEBUG is not set
+# CONFIG_MMC_UNSAFE_RESUME is not set
+
+#
+# MMC/SD Card Drivers
+#
+CONFIG_MMC_BLOCK=m
+
+#
+# MMC/SD Host Controller Drivers
+#
+CONFIG_MMC_PXA=m
+
+#
+# Real Time Clock
+#
+CONFIG_RTC_LIB=y
+CONFIG_RTC_CLASS=m
+
+#
+# RTC interfaces
+#
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_DEV=y
+# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
+# CONFIG_RTC_DRV_TEST is not set
+
+#
+# I2C RTC drivers
+#
+
+#
+# SPI RTC drivers
+#
+
+#
+# Platform RTC drivers
+#
+# CONFIG_RTC_DRV_CMOS is not set
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+CONFIG_RTC_DRV_V3020=m
+
+#
+# on-CPU RTC drivers
+#
+CONFIG_RTC_DRV_SA1100=m
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_XATTR=y
+# CONFIG_EXT3_FS_POSIX_ACL is not set
+# CONFIG_EXT3_FS_SECURITY is not set
+# CONFIG_EXT4DEV_FS is not set
+CONFIG_JBD=y
+# CONFIG_JBD_DEBUG is not set
+CONFIG_FS_MBCACHE=y
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+CONFIG_DNOTIFY=y
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+CONFIG_FAT_FS=y
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_CODEPAGE=437
+CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+CONFIG_RAMFS=y
+# CONFIG_CONFIGFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+CONFIG_JFFS2_SUMMARY=y
+# CONFIG_JFFS2_FS_XATTR is not set
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_ZLIB=y
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
+# CONFIG_CRAMFS is not set
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+
+#
+# Network File Systems
+#
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_SUNRPC_BIND34 is not set
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+CONFIG_SMB_FS=y
+# CONFIG_SMB_NLS_DEFAULT is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+# CONFIG_9P_FS is not set
+
+#
+# Partition Types
+#
+# CONFIG_PARTITION_ADVANCED is not set
+CONFIG_MSDOS_PARTITION=y
+
+#
+# Native Language Support
+#
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="iso8859-1"
+CONFIG_NLS_CODEPAGE_437=y
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+# CONFIG_NLS_CODEPAGE_850 is not set
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+# CONFIG_NLS_ASCII is not set
+CONFIG_NLS_ISO8859_1=y
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+# CONFIG_NLS_ISO8859_15 is not set
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+CONFIG_NLS_UTF8=y
+
+#
+# Distributed Lock Manager
+#
+# CONFIG_DLM is not set
+
+#
+# Profiling support
+#
+# CONFIG_PROFILING is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+# CONFIG_DETECT_SOFTLOCKUP is not set
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+CONFIG_DEBUG_INFO=y
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_LIST is not set
+CONFIG_FRAME_POINTER=y
+CONFIG_FORCED_INLINING=y
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_FAULT_INJECTION is not set
+CONFIG_DEBUG_USER=y
+CONFIG_DEBUG_ERRORS=y
+CONFIG_DEBUG_LL=y
+# CONFIG_DEBUG_ICEDCC is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+
+#
+# Cryptographic options
+#
+CONFIG_CRYPTO=y
+CONFIG_CRYPTO_ALGAPI=m
+CONFIG_CRYPTO_BLKCIPHER=m
+CONFIG_CRYPTO_MANAGER=m
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_MD4 is not set
+# CONFIG_CRYPTO_MD5 is not set
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_WP512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_GF128MUL is not set
+CONFIG_CRYPTO_ECB=m
+CONFIG_CRYPTO_CBC=m
+CONFIG_CRYPTO_PCBC=m
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_DES is not set
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+# CONFIG_CRYPTO_SERPENT is not set
+CONFIG_CRYPTO_AES=m
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+# CONFIG_CRYPTO_TEA is not set
+CONFIG_CRYPTO_ARC4=m
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Hardware crypto devices
+#
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC32=y
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_PLIST=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
diff --git a/arch/arm/configs/s3c2410_defconfig b/arch/arm/configs/s3c2410_defconfig
index 1d5150e..f8a1645 100644
--- a/arch/arm/configs/s3c2410_defconfig
+++ b/arch/arm/configs/s3c2410_defconfig
@@ -138,11 +138,11 @@
 CONFIG_PLAT_S3C24XX=y
 CONFIG_CPU_S3C244X=y
 CONFIG_PM_SIMTEC=y
-# CONFIG_S3C2410_BOOT_WATCHDOG is not set
-# CONFIG_S3C2410_BOOT_ERROR_RESET is not set
+# CONFIG_S3C_BOOT_WATCHDOG is not set
+# CONFIG_S3C_BOOT_ERROR_RESET is not set
 # CONFIG_S3C2410_PM_DEBUG is not set
 # CONFIG_S3C2410_PM_CHECK is not set
-CONFIG_S3C2410_LOWLEVEL_UART_PORT=0
+CONFIG_S3C_LOWLEVEL_UART_PORT=0
 CONFIG_S3C2410_DMA=y
 # CONFIG_S3C2410_DMA_DEBUG is not set
 CONFIG_MACH_SMDK=y
@@ -1392,8 +1392,8 @@
 # CONFIG_DEBUG_ERRORS is not set
 CONFIG_DEBUG_LL=y
 # CONFIG_DEBUG_ICEDCC is not set
-CONFIG_DEBUG_S3C2410_PORT=y
-CONFIG_DEBUG_S3C2410_UART=0
+CONFIG_DEBUG_S3C_PORT=y
+CONFIG_DEBUG_S3C_UART=0
 
 #
 # Security options
diff --git a/arch/arm/mach-at91/at91rm9200_devices.c b/arch/arm/mach-at91/at91rm9200_devices.c
index 70599bc..0417c16 100644
--- a/arch/arm/mach-at91/at91rm9200_devices.c
+++ b/arch/arm/mach-at91/at91rm9200_devices.c
@@ -477,7 +477,7 @@
  *  SPI
  * -------------------------------------------------------------------- */
 
-#if defined(CONFIG_SPI_AT91) || defined(CONFIG_SPI_AT91_MODULE) || defined(CONFIG_AT91_SPI) || defined(CONFIG_AT91_SPI_MODULE)
+#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
 static u64 spi_dmamask = 0xffffffffUL;
 
 static struct resource spi_resources[] = {
@@ -494,7 +494,7 @@
 };
 
 static struct platform_device at91rm9200_spi_device = {
-	.name		= "at91_spi",
+	.name		= "atmel_spi",
 	.id		= 0,
 	.dev		= {
 				.dma_mask		= &spi_dmamask,
@@ -522,18 +522,14 @@
 		else
 			cs_pin = spi_standard_cs[devices[i].chip_select];
 
-#ifdef CONFIG_SPI_AT91_MANUAL_CS
+		/* enable chip-select pin */
 		at91_set_gpio_output(cs_pin, 1);
-#else
-		at91_set_A_periph(cs_pin, 0);
-#endif
 
 		/* pass chip-select pin to driver */
 		devices[i].controller_data = (void *) cs_pin;
 	}
 
 	spi_register_board_info(devices, nr_devices);
-	at91_clock_associate("spi_clk", &at91rm9200_spi_device.dev, "spi");
 	platform_device_register(&at91rm9200_spi_device);
 }
 #else
diff --git a/arch/arm/mach-ixp4xx/common.c b/arch/arm/mach-ixp4xx/common.c
index 8112f72..4c54a86 100644
--- a/arch/arm/mach-ixp4xx/common.c
+++ b/arch/arm/mach-ixp4xx/common.c
@@ -188,7 +188,7 @@
 	*int_reg |= (int_style << (line * IXP4XX_GPIO_STYLE_SIZE));
 
 	/* Configure the line as an input */
-	gpio_line_config(line, IXP4XX_GPIO_IN);
+	gpio_line_config(irq2gpio[irq], IXP4XX_GPIO_IN);
 
 	return 0;
 }
diff --git a/arch/arm/mach-ks8695/irq.c b/arch/arm/mach-ks8695/irq.c
index 2407bba..4c3ab43 100644
--- a/arch/arm/mach-ks8695/irq.c
+++ b/arch/arm/mach-ks8695/irq.c
@@ -23,7 +23,6 @@
 #include <linux/module.h>
 #include <linux/interrupt.h>
 #include <linux/ioport.h>
-#include <linux/ptrace.h>
 #include <linux/sysdev.h>
 
 #include <asm/hardware.h>
diff --git a/arch/arm/mach-mx3/Kconfig b/arch/arm/mach-mx3/Kconfig
new file mode 100644
index 0000000..5fe8606
--- /dev/null
+++ b/arch/arm/mach-mx3/Kconfig
@@ -0,0 +1,12 @@
+menu "MX3 Options"
+	depends on ARCH_MX3
+
+config MACH_MX31ADS
+	bool "Support MX31ADS platforms"
+	default y
+	help
+	  Include support for MX31ADS platform. This includes specific
+	  configurations for the board and its peripherals.
+
+endmenu
+
diff --git a/arch/arm/mach-mx3/Makefile b/arch/arm/mach-mx3/Makefile
new file mode 100644
index 0000000..cbec997
--- /dev/null
+++ b/arch/arm/mach-mx3/Makefile
@@ -0,0 +1,8 @@
+#
+# Makefile for the linux kernel.
+#
+
+# Object file lists.
+
+obj-y			:= mm.o time.o
+obj-$(CONFIG_MACH_MX31ADS)	+= mx31ads.o
diff --git a/arch/arm/mach-mx3/Makefile.boot b/arch/arm/mach-mx3/Makefile.boot
new file mode 100644
index 0000000..e1dd366
--- /dev/null
+++ b/arch/arm/mach-mx3/Makefile.boot
@@ -0,0 +1,3 @@
+   zreladdr-y	:= 0x80008000
+params_phys-y	:= 0x80000100
+initrd_phys-y	:= 0x80800000
diff --git a/arch/arm/mach-mx3/mm.c b/arch/arm/mach-mx3/mm.c
new file mode 100644
index 0000000..41dad48
--- /dev/null
+++ b/arch/arm/mach-mx3/mm.c
@@ -0,0 +1,64 @@
+/*
+ *  Copyright (C) 1999,2000 Arm Limited
+ *  Copyright (C) 2000 Deep Blue Solutions Ltd
+ *  Copyright (C) 2002 Shane Nay (shane@minirl.com)
+ *  Copyright 2005-2007 Freescale Semiconductor, Inc. All Rights Reserved.
+ *    - add MX31 specific definitions
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/mm.h>
+#include <linux/init.h>
+#include <asm/hardware.h>
+#include <asm/pgtable.h>
+#include <asm/mach/map.h>
+#include <asm/arch/common.h>
+
+/*!
+ * @file mm.c
+ *
+ * @brief This file creates static virtual to physical mappings, common to all MX3 boards.
+ *
+ * @ingroup Memory
+ */
+
+/*!
+ * This table defines static virtual address mappings for I/O regions.
+ * These are the mappings common across all MX3 boards.
+ */
+static struct map_desc mxc_io_desc[] __initdata = {
+	{
+		.virtual	= X_MEMC_BASE_ADDR_VIRT,
+		.pfn		= __phys_to_pfn(X_MEMC_BASE_ADDR),
+		.length		= X_MEMC_SIZE,
+		.type		= MT_DEVICE
+	}, {
+		.virtual	= AVIC_BASE_ADDR_VIRT,
+		.pfn		= __phys_to_pfn(AVIC_BASE_ADDR),
+		.length		= AVIC_SIZE,
+		.type		= MT_NONSHARED_DEVICE
+	},
+};
+
+/*!
+ * This function initializes the memory map. It is called during the
+ * system startup to create static physical to virtual memory mappings
+ * for the IO modules.
+ */
+void __init mxc_map_io(void)
+{
+	iotable_init(mxc_io_desc, ARRAY_SIZE(mxc_io_desc));
+}
diff --git a/arch/arm/mach-mx3/mx31ads.c b/arch/arm/mach-mx3/mx31ads.c
new file mode 100644
index 0000000..7e89bdc
--- /dev/null
+++ b/arch/arm/mach-mx3/mx31ads.c
@@ -0,0 +1,142 @@
+/*
+ *  Copyright (C) 2000 Deep Blue Solutions Ltd
+ *  Copyright (C) 2002 Shane Nay (shane@minirl.com)
+ *  Copyright 2005-2007 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/clk.h>
+#include <linux/serial_8250.h>
+
+#include <asm/hardware.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/memory.h>
+#include <asm/mach/map.h>
+#include <asm/arch/common.h>
+
+/*!
+ * @file mx31ads.c
+ *
+ * @brief This file contains the board-specific initialization routines.
+ *
+ * @ingroup System
+ */
+
+#if defined(CONFIG_SERIAL_8250) || defined(CONFIG_SERIAL_8250_MODULE)
+/*!
+ * The serial port definition structure.
+ */
+static struct plat_serial8250_port serial_platform_data[] = {
+	{
+		.membase  = (void *)(PBC_BASE_ADDRESS + PBC_SC16C652_UARTA),
+		.mapbase  = (unsigned long)(CS4_BASE_ADDR + PBC_SC16C652_UARTA),
+		.irq      = EXPIO_INT_XUART_INTA,
+		.uartclk  = 14745600,
+		.regshift = 0,
+		.iotype   = UPIO_MEM,
+		.flags    = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_AUTO_IRQ,
+	}, {
+		.membase  = (void *)(PBC_BASE_ADDRESS + PBC_SC16C652_UARTB),
+		.mapbase  = (unsigned long)(CS4_BASE_ADDR + PBC_SC16C652_UARTB),
+		.irq      = EXPIO_INT_XUART_INTB,
+		.uartclk  = 14745600,
+		.regshift = 0,
+		.iotype   = UPIO_MEM,
+		.flags    = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_AUTO_IRQ,
+	},
+	{},
+};
+
+static struct platform_device serial_device = {
+	.name	= "serial8250",
+	.id	= 0,
+	.dev	= {
+		.platform_data = serial_platform_data,
+	},
+};
+
+static int __init mxc_init_extuart(void)
+{
+	return platform_device_register(&serial_device);
+}
+#else
+static inline int mxc_init_extuart(void)
+{
+	return 0;
+}
+#endif
+
+/*!
+ * This structure defines static mappings for the i.MX31ADS board.
+ */
+static struct map_desc mx31ads_io_desc[] __initdata = {
+	{
+		.virtual	= AIPS1_BASE_ADDR_VIRT,
+		.pfn		= __phys_to_pfn(AIPS1_BASE_ADDR),
+		.length		= AIPS1_SIZE,
+		.type		= MT_NONSHARED_DEVICE
+	}, {
+		.virtual	= SPBA0_BASE_ADDR_VIRT,
+		.pfn		= __phys_to_pfn(SPBA0_BASE_ADDR),
+		.length		= SPBA0_SIZE,
+		.type		= MT_NONSHARED_DEVICE
+	}, {
+		.virtual	= AIPS2_BASE_ADDR_VIRT,
+		.pfn		= __phys_to_pfn(AIPS2_BASE_ADDR),
+		.length		= AIPS2_SIZE,
+		.type		= MT_NONSHARED_DEVICE
+	}, {
+		.virtual	= CS4_BASE_ADDR_VIRT,
+		.pfn		= __phys_to_pfn(CS4_BASE_ADDR),
+		.length		= CS4_SIZE / 2,
+		.type		= MT_DEVICE
+	},
+};
+
+/*!
+ * Set up static virtual mappings.
+ */
+void __init mx31ads_map_io(void)
+{
+	mxc_map_io();
+	iotable_init(mx31ads_io_desc, ARRAY_SIZE(mx31ads_io_desc));
+}
+
+/*!
+ * Board specific initialization.
+ */
+static void __init mxc_board_init(void)
+{
+	mxc_init_extuart();
+}
+
+/*
+ * The following uses standard kernel macros defined in arch.h in order to
+ * initialize __mach_desc_MX31ADS data structure.
+ */
+MACHINE_START(MX31ADS, "Freescale MX31ADS")
+	/* Maintainer: Freescale Semiconductor, Inc. */
+	.phys_io	= AIPS1_BASE_ADDR,
+	.io_pg_offst	= ((AIPS1_BASE_ADDR_VIRT) >> 18) & 0xfffc,
+	.boot_params    = PHYS_OFFSET + 0x100,
+	.map_io         = mx31ads_map_io,
+	.init_irq       = mxc_init_irq,
+	.init_machine   = mxc_board_init,
+	.timer          = &mxc_timer,
+MACHINE_END
diff --git a/arch/arm/mach-mx3/time.c b/arch/arm/mach-mx3/time.c
new file mode 100644
index 0000000..e81fb5c
--- /dev/null
+++ b/arch/arm/mach-mx3/time.c
@@ -0,0 +1,152 @@
+/*
+ * System Timer Interrupt reconfigured to run in free-run mode.
+ * Author: Vitaly Wool
+ * Copyright 2004 MontaVista Software Inc.
+ * Copyright 2004-2007 Freescale Semiconductor, Inc. All Rights Reserved.
+ */
+
+/*
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*!
+ * @file time.c
+ * @brief This file contains OS tick and wdog timer implementations.
+ *
+ * This file contains OS tick and wdog timer implementations.
+ *
+ * @ingroup Timers
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <asm/hardware.h>
+#include <asm/mach/time.h>
+#include <asm/io.h>
+#include <asm/arch/common.h>
+
+/*!
+ * This is the timer interrupt service routine to do required tasks.
+ * It also services the WDOG timer at the frequency of twice per WDOG
+ * timeout value. For example, if the WDOG's timeout value is 4 (2
+ * seconds since the WDOG runs at 0.5Hz), it will be serviced once
+ * every 2/2=1 second.
+ *
+ * @param  irq          GPT interrupt source number (not used)
+ * @param  dev_id       this parameter is not used
+ * @return always returns \b IRQ_HANDLED as defined in
+ *         include/linux/interrupt.h.
+ */
+static irqreturn_t mxc_timer_interrupt(int irq, void *dev_id)
+{
+	unsigned int next_match;
+
+	write_seqlock(&xtime_lock);
+
+	if (__raw_readl(MXC_GPT_GPTSR) & GPTSR_OF1) {
+		do {
+			timer_tick();
+			next_match = __raw_readl(MXC_GPT_GPTOCR1) + LATCH;
+			__raw_writel(GPTSR_OF1, MXC_GPT_GPTSR);
+			__raw_writel(next_match, MXC_GPT_GPTOCR1);
+		} while ((signed long)(next_match -
+				       __raw_readl(MXC_GPT_GPTCNT)) <= 0);
+	}
+
+	write_sequnlock(&xtime_lock);
+
+	return IRQ_HANDLED;
+}
+
+/*!
+ * This function is used to obtain the number of microseconds since the last
+ * timer interrupt. Note that interrupts is disabled by do_gettimeofday().
+ *
+ * @return the number of microseconds since the last timer interrupt.
+ */
+static unsigned long mxc_gettimeoffset(void)
+{
+	unsigned long ticks_to_match, elapsed, usec, tick_usec, i;
+
+	/* Get ticks before next timer match */
+	ticks_to_match =
+	    __raw_readl(MXC_GPT_GPTOCR1) - __raw_readl(MXC_GPT_GPTCNT);
+
+	/* We need elapsed ticks since last match */
+	elapsed = LATCH - ticks_to_match;
+
+	/* Now convert them to usec */
+	/* Insure no overflow when calculating the usec below */
+	for (i = 1, tick_usec = tick_nsec / 1000;; i *= 2) {
+		tick_usec /= i;
+		if ((0xFFFFFFFF / tick_usec) > elapsed)
+			break;
+	}
+	usec = (unsigned long)(elapsed * tick_usec) / (LATCH / i);
+
+	return usec;
+}
+
+/*!
+ * The OS tick timer interrupt structure.
+ */
+static struct irqaction timer_irq = {
+	.name = "MXC Timer Tick",
+	.flags = IRQF_DISABLED | IRQF_TIMER,
+	.handler = mxc_timer_interrupt
+};
+
+/*!
+ * This function is used to initialize the GPT to produce an interrupt
+ * based on HZ.  It is called by start_kernel() during system startup.
+ */
+void __init mxc_init_time(void)
+{
+	u32 reg, v;
+	reg = __raw_readl(MXC_GPT_GPTCR);
+	reg &= ~GPTCR_ENABLE;
+	__raw_writel(reg, MXC_GPT_GPTCR);
+	reg |= GPTCR_SWR;
+	__raw_writel(reg, MXC_GPT_GPTCR);
+
+	while ((__raw_readl(MXC_GPT_GPTCR) & GPTCR_SWR) != 0)
+		cpu_relax();
+
+	reg = GPTCR_FRR | GPTCR_CLKSRC_HIGHFREQ;
+	__raw_writel(reg, MXC_GPT_GPTCR);
+
+	/* TODO: get timer rate from clk driver */
+	v = 66500000;
+
+	__raw_writel((v / CLOCK_TICK_RATE) - 1, MXC_GPT_GPTPR);
+
+	if ((v % CLOCK_TICK_RATE) != 0) {
+		pr_info("\nWARNING: Can't generate CLOCK_TICK_RATE at %d Hz\n",
+			CLOCK_TICK_RATE);
+	}
+	pr_info("Actual CLOCK_TICK_RATE is %d Hz\n",
+		v / ((__raw_readl(MXC_GPT_GPTPR) & 0xFFF) + 1));
+
+	reg = __raw_readl(MXC_GPT_GPTCNT);
+	reg += LATCH;
+	__raw_writel(reg, MXC_GPT_GPTOCR1);
+
+	setup_irq(MXC_INT_GPT, &timer_irq);
+
+	reg = __raw_readl(MXC_GPT_GPTCR);
+	reg =
+	    GPTCR_FRR | GPTCR_CLKSRC_HIGHFREQ | GPTCR_STOPEN | GPTCR_DOZEN |
+	    GPTCR_WAITEN | GPTCR_ENMOD | GPTCR_ENABLE;
+	__raw_writel(reg, MXC_GPT_GPTCR);
+
+	__raw_writel(GPTIR_OF1IE, MXC_GPT_GPTIR);
+}
+
+struct sys_timer mxc_timer = {
+	.init = mxc_init_time,
+	.offset = mxc_gettimeoffset,
+};
diff --git a/arch/arm/mach-ns9xxx/Makefile b/arch/arm/mach-ns9xxx/Makefile
index 53213a6..4476411 100644
--- a/arch/arm/mach-ns9xxx/Makefile
+++ b/arch/arm/mach-ns9xxx/Makefile
@@ -1,6 +1,7 @@
 obj-y := irq.o time.o generic.o
 
 obj-$(CONFIG_MACH_CC9P9360DEV) += mach-cc9p9360dev.o
+obj-$(CONFIG_MACH_CC9P9360JS) += mach-cc9p9360js.o
 
 obj-$(CONFIG_BOARD_A9M9750DEV) += board-a9m9750dev.o
 obj-$(CONFIG_BOARD_JSCC9P9360) += board-jscc9p9360.o
diff --git a/arch/arm/mach-ns9xxx/board-a9m9750dev.c b/arch/arm/mach-ns9xxx/board-a9m9750dev.c
index 2528988..925048e 100644
--- a/arch/arm/mach-ns9xxx/board-a9m9750dev.c
+++ b/arch/arm/mach-ns9xxx/board-a9m9750dev.c
@@ -77,7 +77,7 @@
 
 		desc = irq_desc + FPGA_IRQ(irqno);
 
-		desc_handle_irq(irqno, desc);
+		desc_handle_irq(FPGA_IRQ(irqno), desc);
 	}
 }
 
@@ -91,7 +91,7 @@
 	 * use GPIO 11, because GPIO 32 is used for the LCD
 	 */
 	/* XXX: proper GPIO handling */
-	BBU_GC(2) &= ~0x2000;
+	BBU_GCONFb1(1) &= ~0x2000;
 
 	for (i = FPGA_IRQ(0); i <= FPGA_IRQ(7); ++i) {
 		set_irq_chip(i, &a9m9750dev_fpga_chip);
@@ -178,7 +178,7 @@
 
 	/* setup static CS0: memory configuration */
 	reg = MEM_SMC(0);
-	REGSET(reg, MEM_SMC, WSMC, OFF);
+	REGSET(reg, MEM_SMC, PSMC, OFF);
 	REGSET(reg, MEM_SMC, BSMC, OFF);
 	REGSET(reg, MEM_SMC, EW, OFF);
 	REGSET(reg, MEM_SMC, PB, 1);
@@ -196,4 +196,3 @@
 	platform_add_devices(board_a9m9750dev_devices,
 			ARRAY_SIZE(board_a9m9750dev_devices));
 }
-
diff --git a/arch/arm/mach-ns9xxx/generic.c b/arch/arm/mach-ns9xxx/generic.c
index 83e2b65..d742c92 100644
--- a/arch/arm/mach-ns9xxx/generic.c
+++ b/arch/arm/mach-ns9xxx/generic.c
@@ -18,6 +18,8 @@
 #include <asm/arch-ns9xxx/regs-mem.h>
 #include <asm/arch-ns9xxx/board.h>
 
+#include "generic.h"
+
 static struct map_desc standard_io_desc[] __initdata = {
 	{ /* BBus */
 		.virtual = io_p2v(0x90000000),
diff --git a/arch/arm/mach-ns9xxx/irq.c b/arch/arm/mach-ns9xxx/irq.c
index 83d9272..b8c7b00 100644
--- a/arch/arm/mach-ns9xxx/irq.c
+++ b/arch/arm/mach-ns9xxx/irq.c
@@ -21,6 +21,15 @@
 {
 	u32 tc = SYS_TC(irq - IRQ_TIMER0);
 
+	/*
+	 * If the timer is programmed to halt on terminal count, the
+	 * timer must be disabled before clearing the interrupt.
+	 */
+	if (REGGET(tc, SYS_TCx, REN) == 0) {
+		REGSET(tc, SYS_TCx, TEN, DIS);
+		SYS_TC(irq - IRQ_TIMER0) = tc;
+	}
+
 	REGSET(tc, SYS_TCx, INTC, SET);
 	SYS_TC(irq - IRQ_TIMER0) = tc;
 
@@ -28,7 +37,7 @@
 	SYS_TC(irq - IRQ_TIMER0) = tc;
 }
 
-void (*ns9xxx_ack_irq_functions[NR_IRQS])(unsigned int) = {
+static void (*ns9xxx_ack_irq_functions[NR_IRQS])(unsigned int) = {
 	[IRQ_TIMER0] = ns9xxx_ack_irq_timer,
 	[IRQ_TIMER1] = ns9xxx_ack_irq_timer,
 	[IRQ_TIMER2] = ns9xxx_ack_irq_timer,
diff --git a/arch/arm/mach-ns9xxx/mach-cc9p9360js.c b/arch/arm/mach-ns9xxx/mach-cc9p9360js.c
index d09d5fa..85c8b41 100644
--- a/arch/arm/mach-ns9xxx/mach-cc9p9360js.c
+++ b/arch/arm/mach-ns9xxx/mach-cc9p9360js.c
@@ -20,7 +20,7 @@
 	board_jscc9p9360_init_machine();
 }
 
-MACHINE_START(CC9P9360DEV, "Digi ConnectCore 9P 9360 on an JSCC9P9360 Devboard")
+MACHINE_START(CC9P9360JS, "Digi ConnectCore 9P 9360 on an JSCC9P9360 Devboard")
 	.map_io = ns9xxx_map_io,
 	.init_irq = ns9xxx_init_irq,
 	.init_machine = mach_cc9p9360js_init_machine,
diff --git a/arch/arm/mach-pxa/Kconfig b/arch/arm/mach-pxa/Kconfig
index 5c0a100..5ebec6d 100644
--- a/arch/arm/mach-pxa/Kconfig
+++ b/arch/arm/mach-pxa/Kconfig
@@ -37,6 +37,10 @@
 	bool "Keith und Koep Trizeps4 DIMM-Module"
 	select PXA27x
 
+config MACH_EM_X270
+	bool "CompuLab EM-x270 platform"
+	select PXA27x
+
 endchoice
 
 if PXA_SHARPSL
diff --git a/arch/arm/mach-pxa/Makefile b/arch/arm/mach-pxa/Makefile
index 9093eb1c9..7d6ab5c 100644
--- a/arch/arm/mach-pxa/Makefile
+++ b/arch/arm/mach-pxa/Makefile
@@ -18,6 +18,7 @@
 obj-$(CONFIG_MACH_AKITA)	+= akita-ioexp.o
 obj-$(CONFIG_MACH_POODLE)	+= poodle.o corgi_ssp.o
 obj-$(CONFIG_MACH_TOSA)         += tosa.o
+obj-$(CONFIG_MACH_EM_X270) += em-x270.o
 
 # Support for blinky lights
 led-y := leds.o
diff --git a/arch/arm/mach-pxa/devices.h b/arch/arm/mach-pxa/devices.h
index 9a6faff..636fdb1 100644
--- a/arch/arm/mach-pxa/devices.h
+++ b/arch/arm/mach-pxa/devices.h
@@ -1,11 +1,11 @@
-extern struct platform_device pxamci_device;
-extern struct platform_device pxaudc_device;
-extern struct platform_device pxafb_device;
-extern struct platform_device ffuart_device;
-extern struct platform_device btuart_device;
-extern struct platform_device stuart_device;
-extern struct platform_device hwuart_device;
-extern struct platform_device pxai2c_device;
-extern struct platform_device pxai2s_device;
-extern struct platform_device pxaficp_device;
-extern struct platform_device pxartc_device;
+extern struct platform_device pxa_device_mci;
+extern struct platform_device pxa_device_udc;
+extern struct platform_device pxa_device_fb;
+extern struct platform_device pxa_device_ffuart;
+extern struct platform_device pxa_device_btuart;
+extern struct platform_device pxa_device_stuart;
+extern struct platform_device pxa_device_hwuart;
+extern struct platform_device pxa_device_i2c;
+extern struct platform_device pxa_device_i2s;
+extern struct platform_device pxa_device_ficp;
+extern struct platform_device pxa_device_rtc;
diff --git a/arch/arm/mach-pxa/em-x270.c b/arch/arm/mach-pxa/em-x270.c
new file mode 100644
index 0000000..3d0ad50
--- /dev/null
+++ b/arch/arm/mach-pxa/em-x270.c
@@ -0,0 +1,354 @@
+/*
+ * Support for CompuLab EM-x270 platform
+ *
+ * Copyright (C) 2007 CompuLab, Ltd.
+ * Author: Mike Rapoport <mike@compulab.co.il>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/irq.h>
+#include <linux/platform_device.h>
+
+#include <linux/dm9000.h>
+#include <linux/rtc-v3020.h>
+
+#include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
+
+#include <asm/mach-types.h>
+
+#include <asm/mach/arch.h>
+
+#include <asm/arch/pxa-regs.h>
+#include <asm/arch/pxafb.h>
+#include <asm/arch/ohci.h>
+#include <asm/arch/mmc.h>
+#include <asm/arch/bitfield.h>
+
+#include "generic.h"
+
+/* GPIO IRQ usage */
+#define EM_X270_MMC_PD		(105)
+#define EM_X270_ETHIRQ		IRQ_GPIO(41)
+#define EM_X270_MMC_IRQ		IRQ_GPIO(13)
+
+static struct resource em_x270_dm9k_resource[] = {
+	[0] = {
+		.start = PXA_CS2_PHYS,
+		.end   = PXA_CS2_PHYS + 3,
+		.flags = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start = PXA_CS2_PHYS + 8,
+		.end   = PXA_CS2_PHYS + 8 + 0x3f,
+		.flags = IORESOURCE_MEM,
+	},
+	[2] = {
+		.start = EM_X270_ETHIRQ,
+		.end   = EM_X270_ETHIRQ,
+		.flags = IORESOURCE_IRQ,
+	}
+};
+
+/* for the moment we limit ourselves to 32bit IO until some
+ * better IO routines can be written and tested
+ */
+static struct dm9000_plat_data em_x270_dm9k_platdata = {
+	.flags		= DM9000_PLATF_32BITONLY,
+};
+
+/* Ethernet device */
+static struct platform_device em_x270_dm9k = {
+	.name		= "dm9000",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(em_x270_dm9k_resource),
+	.resource	= em_x270_dm9k_resource,
+	.dev		= {
+		.platform_data = &em_x270_dm9k_platdata,
+	}
+};
+
+/* audio device */
+static struct platform_device em_x270_audio = {
+	.name		= "pxa2xx-ac97",
+	.id		= -1,
+};
+
+/* WM9712 touchscreen controller. Hopefully the driver will make it to
+ * the mainstream sometime */
+static struct platform_device em_x270_ts = {
+	.name		= "wm97xx-ts",
+	.id		= -1,
+};
+
+/* RTC */
+static struct resource em_x270_v3020_resource[] = {
+	[0] = {
+		.start = PXA_CS4_PHYS,
+		.end   = PXA_CS4_PHYS + 3,
+		.flags = IORESOURCE_MEM,
+	},
+};
+
+static struct v3020_platform_data em_x270_v3020_platdata = {
+	.leftshift = 0,
+};
+
+static struct platform_device em_x270_rtc = {
+	.name		= "v3020",
+	.num_resources	= ARRAY_SIZE(em_x270_v3020_resource),
+	.resource	= em_x270_v3020_resource,
+	.id		= -1,
+	.dev		= {
+		.platform_data = &em_x270_v3020_platdata,
+	}
+};
+
+/* NAND flash */
+#define GPIO_NAND_CS	(11)
+#define GPIO_NAND_RB	(56)
+
+static inline void nand_cs_on(void)
+{
+	GPCR(GPIO_NAND_CS) = GPIO_bit(GPIO_NAND_CS);
+}
+
+static void nand_cs_off(void)
+{
+	dsb();
+
+	GPSR(GPIO_NAND_CS) = GPIO_bit(GPIO_NAND_CS);
+}
+
+/* hardware specific access to control-lines */
+static void em_x270_nand_cmd_ctl(struct mtd_info *mtd, int dat,
+				 unsigned int ctrl)
+{
+	struct nand_chip *this = mtd->priv;
+	unsigned long nandaddr = (unsigned long)this->IO_ADDR_W;
+
+	dsb();
+
+	if (ctrl & NAND_CTRL_CHANGE) {
+		if (ctrl & NAND_ALE)
+			nandaddr |=  (1 << 3);
+		else
+			nandaddr &= ~(1 << 3);
+		if (ctrl & NAND_CLE)
+			nandaddr |=  (1 << 2);
+		else
+			nandaddr &= ~(1 << 2);
+		if (ctrl & NAND_NCE)
+			nand_cs_on();
+		else
+			nand_cs_off();
+	}
+
+	dsb();
+	this->IO_ADDR_W = (void __iomem *)nandaddr;
+	if (dat != NAND_CMD_NONE)
+		writel(dat, this->IO_ADDR_W);
+
+	dsb();
+}
+
+/* read device ready pin */
+static int em_x270_nand_device_ready(struct mtd_info *mtd)
+{
+	dsb();
+
+	return GPLR(GPIO_NAND_RB) & GPIO_bit(GPIO_NAND_RB);
+}
+
+static struct mtd_partition em_x270_partition_info[] = {
+	[0] = {
+		.name	= "em_x270-0",
+		.offset	= 0,
+		.size	= SZ_4M,
+	},
+	[1] = {
+		.name	= "em_x270-1",
+		.offset	= MTDPART_OFS_APPEND,
+		.size	= MTDPART_SIZ_FULL
+	},
+};
+
+static const char *em_x270_part_probes[] = { "cmdlinepart", NULL };
+
+struct platform_nand_data em_x270_nand_platdata = {
+	.chip = {
+		.nr_chips = 1,
+		.chip_offset = 0,
+		.nr_partitions = ARRAY_SIZE(em_x270_partition_info),
+		.partitions = em_x270_partition_info,
+		.chip_delay = 20,
+		.part_probe_types = em_x270_part_probes,
+	},
+	.ctrl = {
+		.hwcontrol = 0,
+		.dev_ready = em_x270_nand_device_ready,
+		.select_chip = 0,
+		.cmd_ctrl = em_x270_nand_cmd_ctl,
+	},
+};
+
+static struct resource em_x270_nand_resource[] = {
+	[0] = {
+		.start = PXA_CS1_PHYS,
+		.end   = PXA_CS1_PHYS + 12,
+		.flags = IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device em_x270_nand = {
+	.name		= "gen_nand",
+	.num_resources	= ARRAY_SIZE(em_x270_nand_resource),
+	.resource	= em_x270_nand_resource,
+	.id		= -1,
+	.dev		= {
+		.platform_data = &em_x270_nand_platdata,
+	}
+};
+
+/* platform devices */
+static struct platform_device *platform_devices[] __initdata = {
+	&em_x270_dm9k,
+	&em_x270_audio,
+	&em_x270_ts,
+	&em_x270_rtc,
+	&em_x270_nand,
+};
+
+
+/* PXA27x OHCI controller setup */
+static int em_x270_ohci_init(struct device *dev)
+{
+	/* Set the Power Control Polarity Low */
+	UHCHR = (UHCHR | UHCHR_PCPL) &
+		~(UHCHR_SSEP1 | UHCHR_SSEP2 | UHCHR_SSE);
+
+	/* enable port 2 transiever */
+	UP2OCR = UP2OCR_HXS | UP2OCR_HXOE;
+
+	return 0;
+}
+
+static struct pxaohci_platform_data em_x270_ohci_platform_data = {
+	.port_mode	= PMM_PERPORT_MODE,
+	.init		= em_x270_ohci_init,
+};
+
+
+static int em_x270_mci_init(struct device *dev,
+			    irq_handler_t em_x270_detect_int,
+			    void *data)
+{
+	int err;
+
+	/* setup GPIO for PXA27x MMC controller */
+	pxa_gpio_mode(GPIO32_MMCCLK_MD);
+	pxa_gpio_mode(GPIO112_MMCCMD_MD);
+	pxa_gpio_mode(GPIO92_MMCDAT0_MD);
+	pxa_gpio_mode(GPIO109_MMCDAT1_MD);
+	pxa_gpio_mode(GPIO110_MMCDAT2_MD);
+	pxa_gpio_mode(GPIO111_MMCDAT3_MD);
+
+	/* EM-X270 uses GPIO13 as SD power enable */
+	pxa_gpio_mode(EM_X270_MMC_PD | GPIO_OUT);
+
+	err = request_irq(EM_X270_MMC_IRQ, em_x270_detect_int,
+			  IRQF_DISABLED | IRQF_TRIGGER_FALLING,
+			  "MMC card detect", data);
+	if (err) {
+		printk(KERN_ERR "%s: can't request MMC card detect IRQ: %d\n",
+		       __FUNCTION__, err);
+		return err;
+	}
+
+	return 0;
+}
+
+static void em_x270_mci_setpower(struct device *dev, unsigned int vdd)
+{
+	/*
+	   FIXME: current hardware implementation does not allow to
+	   enable/disable MMC power. This will be fixed in next HW releases,
+	   and we'll need to add implmentation here.
+	*/
+	return;
+}
+
+static void em_x270_mci_exit(struct device *dev, void *data)
+{
+	free_irq(EM_X270_MMC_IRQ, data);
+}
+
+static struct pxamci_platform_data em_x270_mci_platform_data = {
+	.ocr_mask	= MMC_VDD_28_29|MMC_VDD_29_30|MMC_VDD_30_31,
+	.init 		= em_x270_mci_init,
+	.setpower 	= em_x270_mci_setpower,
+	.exit		= em_x270_mci_exit,
+};
+
+/* LCD 480x640 */
+static struct pxafb_mode_info em_x270_lcd_mode = {
+	.pixclock	= 50000,
+	.bpp		= 16,
+	.xres		= 480,
+	.yres		= 640,
+	.hsync_len	= 8,
+	.vsync_len	= 2,
+	.left_margin	= 8,
+	.upper_margin	= 0,
+	.right_margin	= 24,
+	.lower_margin	= 4,
+	.cmap_greyscale	= 0,
+};
+
+static struct pxafb_mach_info em_x270_lcd = {
+	.modes		= &em_x270_lcd_mode,
+	.num_modes	= 1,
+	.cmap_inverse	= 0,
+	.cmap_static	= 0,
+	.lccr0		= LCCR0_PAS,
+	.lccr3		= LCCR3_PixClkDiv(0x01) | LCCR3_Acb(0xff),
+};
+
+static void __init em_x270_init(void)
+{
+	/* setup LCD */
+	set_pxa_fb_info(&em_x270_lcd);
+
+	/* register EM-X270 platform devices */
+	platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
+
+	/* set MCI and OHCI platform parameters */
+	pxa_set_mci_info(&em_x270_mci_platform_data);
+	pxa_set_ohci_info(&em_x270_ohci_platform_data);
+
+	/* setup STUART GPIOs */
+	pxa_gpio_mode(GPIO46_STRXD_MD);
+	pxa_gpio_mode(GPIO47_STTXD_MD);
+
+	/* setup BTUART GPIOs */
+	pxa_gpio_mode(GPIO42_BTRXD_MD);
+	pxa_gpio_mode(GPIO43_BTTXD_MD);
+	pxa_gpio_mode(GPIO44_BTCTS_MD);
+	pxa_gpio_mode(GPIO45_BTRTS_MD);
+
+	/* Setup interrupt for dm9000 */
+	set_irq_type(EM_X270_ETHIRQ, IRQT_RISING);
+}
+
+MACHINE_START(EM_X270, "Compulab EM-x270")
+	.boot_params	= 0xa0000100,
+	.phys_io	= 0x40000000,
+	.io_pg_offst	= (io_p2v(0x40000000) >> 18) & 0xfffc,
+	.map_io		= pxa_map_io,
+	.init_irq	= pxa27x_init_irq,
+	.timer		= &pxa_timer,
+	.init_machine	= em_x270_init,
+MACHINE_END
diff --git a/arch/arm/mach-pxa/generic.c b/arch/arm/mach-pxa/generic.c
index 296539b..5510f6f 100644
--- a/arch/arm/mach-pxa/generic.c
+++ b/arch/arm/mach-pxa/generic.c
@@ -243,7 +243,7 @@
 
 static u64 pxamci_dmamask = 0xffffffffUL;
 
-struct platform_device pxamci_device = {
+struct platform_device pxa_device_mci = {
 	.name		= "pxa2xx-mci",
 	.id		= -1,
 	.dev		= {
@@ -256,7 +256,7 @@
 
 void __init pxa_set_mci_info(struct pxamci_platform_data *info)
 {
-	pxamci_device.dev.platform_data = info;
+	pxa_device_mci.dev.platform_data = info;
 }
 
 
@@ -282,7 +282,7 @@
 
 static u64 udc_dma_mask = ~(u32)0;
 
-struct platform_device pxaudc_device = {
+struct platform_device pxa_device_udc = {
 	.name		= "pxa2xx-udc",
 	.id		= -1,
 	.resource	= pxa2xx_udc_resources,
@@ -308,7 +308,7 @@
 
 static u64 fb_dma_mask = ~(u64)0;
 
-struct platform_device pxafb_device = {
+struct platform_device pxa_device_fb = {
 	.name		= "pxa2xx-fb",
 	.id		= -1,
 	.dev		= {
@@ -321,27 +321,27 @@
 
 void __init set_pxa_fb_info(struct pxafb_mach_info *info)
 {
-	pxafb_device.dev.platform_data = info;
+	pxa_device_fb.dev.platform_data = info;
 }
 
 void __init set_pxa_fb_parent(struct device *parent_dev)
 {
-	pxafb_device.dev.parent = parent_dev;
+	pxa_device_fb.dev.parent = parent_dev;
 }
 
-struct platform_device ffuart_device = {
+struct platform_device pxa_device_ffuart= {
 	.name		= "pxa2xx-uart",
 	.id		= 0,
 };
-struct platform_device btuart_device = {
+struct platform_device pxa_device_btuart = {
 	.name		= "pxa2xx-uart",
 	.id		= 1,
 };
-struct platform_device stuart_device = {
+struct platform_device pxa_device_stuart = {
 	.name		= "pxa2xx-uart",
 	.id		= 2,
 };
-struct platform_device hwuart_device = {
+struct platform_device pxa_device_hwuart = {
 	.name		= "pxa2xx-uart",
 	.id		= 3,
 };
@@ -358,7 +358,7 @@
 	},
 };
 
-struct platform_device pxai2c_device = {
+struct platform_device pxa_device_i2c = {
 	.name		= "pxa2xx-i2c",
 	.id		= 0,
 	.resource	= pxai2c_resources,
@@ -367,7 +367,7 @@
 
 void __init pxa_set_i2c_info(struct i2c_pxa_platform_data *info)
 {
-	pxai2c_device.dev.platform_data = info;
+	pxa_device_i2c.dev.platform_data = info;
 }
 
 static struct resource pxai2s_resources[] = {
@@ -382,7 +382,7 @@
 	},
 };
 
-struct platform_device pxai2s_device = {
+struct platform_device pxa_device_i2s = {
 	.name		= "pxa2xx-i2s",
 	.id		= -1,
 	.resource	= pxai2s_resources,
@@ -391,7 +391,7 @@
 
 static u64 pxaficp_dmamask = ~(u32)0;
 
-struct platform_device pxaficp_device = {
+struct platform_device pxa_device_ficp = {
 	.name		= "pxa2xx-ir",
 	.id		= -1,
 	.dev		= {
@@ -402,10 +402,10 @@
 
 void __init pxa_set_ficp_info(struct pxaficp_platform_data *info)
 {
-	pxaficp_device.dev.platform_data = info;
+	pxa_device_ficp.dev.platform_data = info;
 }
 
-struct platform_device pxartc_device = {
+struct platform_device pxa_device_rtc = {
 	.name		= "sa1100-rtc",
 	.id		= -1,
 };
diff --git a/arch/arm/mach-pxa/pm.c b/arch/arm/mach-pxa/pm.c
index e66dbc2..b59a81a 100644
--- a/arch/arm/mach-pxa/pm.c
+++ b/arch/arm/mach-pxa/pm.c
@@ -24,61 +24,13 @@
 #include <asm/arch/lubbock.h>
 #include <asm/mach/time.h>
 
-
-/*
- * Debug macros
- */
-#undef DEBUG
-
-#define SAVE(x)		sleep_save[SLEEP_SAVE_##x] = x
-#define RESTORE(x)	x = sleep_save[SLEEP_SAVE_##x]
-
-#define RESTORE_GPLEVEL(n) do { \
-	GPSR##n = sleep_save[SLEEP_SAVE_GPLR##n]; \
-	GPCR##n = ~sleep_save[SLEEP_SAVE_GPLR##n]; \
-} while (0)
-
-/*
- * List of global PXA peripheral registers to preserve.
- * More ones like CP and general purpose register values are preserved
- * with the stack pointer in sleep.S.
- */
-enum {	SLEEP_SAVE_START = 0,
-
-	SLEEP_SAVE_GPLR0, SLEEP_SAVE_GPLR1, SLEEP_SAVE_GPLR2, SLEEP_SAVE_GPLR3,
-	SLEEP_SAVE_GPDR0, SLEEP_SAVE_GPDR1, SLEEP_SAVE_GPDR2, SLEEP_SAVE_GPDR3,
-	SLEEP_SAVE_GRER0, SLEEP_SAVE_GRER1, SLEEP_SAVE_GRER2, SLEEP_SAVE_GRER3,
-	SLEEP_SAVE_GFER0, SLEEP_SAVE_GFER1, SLEEP_SAVE_GFER2, SLEEP_SAVE_GFER3,
-	SLEEP_SAVE_PGSR0, SLEEP_SAVE_PGSR1, SLEEP_SAVE_PGSR2, SLEEP_SAVE_PGSR3,
-
-	SLEEP_SAVE_GAFR0_L, SLEEP_SAVE_GAFR0_U,
-	SLEEP_SAVE_GAFR1_L, SLEEP_SAVE_GAFR1_U,
-	SLEEP_SAVE_GAFR2_L, SLEEP_SAVE_GAFR2_U,
-	SLEEP_SAVE_GAFR3_L, SLEEP_SAVE_GAFR3_U,
-
-	SLEEP_SAVE_PSTR,
-
-	SLEEP_SAVE_ICMR,
-	SLEEP_SAVE_CKEN,
-
-#ifdef CONFIG_PXA27x
- 	SLEEP_SAVE_MDREFR,
- 	SLEEP_SAVE_PWER, SLEEP_SAVE_PCFR, SLEEP_SAVE_PRER,
- 	SLEEP_SAVE_PFER, SLEEP_SAVE_PKWR,
-#endif
-
-	SLEEP_SAVE_CKSUM,
-
-	SLEEP_SAVE_SIZE
-};
-
+struct pxa_cpu_pm_fns *pxa_cpu_pm_fns;
+static unsigned long *sleep_save;
 
 int pxa_pm_enter(suspend_state_t state)
 {
-	unsigned long sleep_save[SLEEP_SAVE_SIZE];
-	unsigned long checksum = 0;
+	unsigned long sleep_save_checksum = 0, checksum = 0;
 	int i;
-	extern void pxa_cpu_pm_enter(suspend_state_t state);
 
 #ifdef CONFIG_IWMMXT
 	/* force any iWMMXt context to ram **/
@@ -86,100 +38,35 @@
 		iwmmxt_task_disable(NULL);
 #endif
 
-	SAVE(GPLR0); SAVE(GPLR1); SAVE(GPLR2);
-	SAVE(GPDR0); SAVE(GPDR1); SAVE(GPDR2);
-	SAVE(GRER0); SAVE(GRER1); SAVE(GRER2);
-	SAVE(GFER0); SAVE(GFER1); SAVE(GFER2);
-	SAVE(PGSR0); SAVE(PGSR1); SAVE(PGSR2);
-
-	SAVE(GAFR0_L); SAVE(GAFR0_U);
-	SAVE(GAFR1_L); SAVE(GAFR1_U);
-	SAVE(GAFR2_L); SAVE(GAFR2_U);
-
-#ifdef CONFIG_PXA27x
-	SAVE(MDREFR);
-	SAVE(GPLR3); SAVE(GPDR3); SAVE(GRER3); SAVE(GFER3); SAVE(PGSR3);
-	SAVE(GAFR3_L); SAVE(GAFR3_U);
-	SAVE(PWER); SAVE(PCFR); SAVE(PRER);
-	SAVE(PFER); SAVE(PKWR);
-#endif
-
-	SAVE(ICMR);
-	ICMR = 0;
-
-	SAVE(CKEN);
-	SAVE(PSTR);
-
-	/* Note: wake up source are set up in each machine specific files */
-
-	/* clear GPIO transition detect  bits */
-	GEDR0 = GEDR0; GEDR1 = GEDR1; GEDR2 = GEDR2;
-#ifdef CONFIG_PXA27x
-	GEDR3 = GEDR3;
-#endif
+	pxa_cpu_pm_fns->save(sleep_save);
 
 	/* Clear sleep reset status */
 	RCSR = RCSR_SMR;
 
 	/* before sleeping, calculate and save a checksum */
-	for (i = 0; i < SLEEP_SAVE_SIZE - 1; i++)
-		checksum += sleep_save[i];
-	sleep_save[SLEEP_SAVE_CKSUM] = checksum;
+	for (i = 0; i < pxa_cpu_pm_fns->save_size - 1; i++)
+		sleep_save_checksum += sleep_save[i];
 
 	/* *** go zzz *** */
-	pxa_cpu_pm_enter(state);
-
+	pxa_cpu_pm_fns->enter(state);
 	cpu_init();
 
 	/* after sleeping, validate the checksum */
-	checksum = 0;
-	for (i = 0; i < SLEEP_SAVE_SIZE - 1; i++)
+	for (i = 0; i < pxa_cpu_pm_fns->save_size - 1; i++)
 		checksum += sleep_save[i];
 
 	/* if invalid, display message and wait for a hardware reset */
-	if (checksum != sleep_save[SLEEP_SAVE_CKSUM]) {
+	if (checksum != sleep_save_checksum) {
 #ifdef CONFIG_ARCH_LUBBOCK
 		LUB_HEXLED = 0xbadbadc5;
 #endif
 		while (1)
-			pxa_cpu_pm_enter(state);
+			pxa_cpu_pm_fns->enter(state);
 	}
 
-	/* ensure not to come back here if it wasn't intended */
-	PSPR = 0;
+	pxa_cpu_pm_fns->restore(sleep_save);
 
-	/* restore registers */
-	RESTORE_GPLEVEL(0); RESTORE_GPLEVEL(1); RESTORE_GPLEVEL(2);
-	RESTORE(GPDR0); RESTORE(GPDR1); RESTORE(GPDR2);
-	RESTORE(GAFR0_L); RESTORE(GAFR0_U);
-	RESTORE(GAFR1_L); RESTORE(GAFR1_U);
-	RESTORE(GAFR2_L); RESTORE(GAFR2_U);
-	RESTORE(GRER0); RESTORE(GRER1); RESTORE(GRER2);
-	RESTORE(GFER0); RESTORE(GFER1); RESTORE(GFER2);
-	RESTORE(PGSR0); RESTORE(PGSR1); RESTORE(PGSR2);
-
-#ifdef CONFIG_PXA27x
-	RESTORE(MDREFR);
-	RESTORE_GPLEVEL(3); RESTORE(GPDR3);
-	RESTORE(GAFR3_L); RESTORE(GAFR3_U);
-	RESTORE(GRER3); RESTORE(GFER3); RESTORE(PGSR3);
-	RESTORE(PWER); RESTORE(PCFR); RESTORE(PRER);
-	RESTORE(PFER); RESTORE(PKWR);
-#endif
-
-	PSSR = PSSR_RDH | PSSR_PH;
-
-	RESTORE(CKEN);
-
-	ICLR = 0;
-	ICCR = 1;
-	RESTORE(ICMR);
-
-	RESTORE(PSTR);
-
-#ifdef DEBUG
-	printk(KERN_DEBUG "*** made it back from resume\n");
-#endif
+	pr_debug("*** made it back from resume\n");
 
 	return 0;
 }
@@ -190,3 +77,35 @@
 {
 	return virt_to_phys(sp);
 }
+
+static int pxa_pm_valid(suspend_state_t state)
+{
+	if (pxa_cpu_pm_fns)
+		return pxa_cpu_pm_fns->valid(state);
+
+	return -EINVAL;
+}
+
+static struct pm_ops pxa_pm_ops = {
+	.valid		= pxa_pm_valid,
+	.enter		= pxa_pm_enter,
+};
+
+static int __init pxa_pm_init(void)
+{
+	if (!pxa_cpu_pm_fns) {
+		printk(KERN_ERR "no valid pxa_cpu_pm_fns defined\n");
+		return -EINVAL;
+	}
+
+	sleep_save = kmalloc(pxa_cpu_pm_fns->save_size, GFP_KERNEL);
+	if (!sleep_save) {
+		printk(KERN_ERR "failed to alloc memory for pm save\n");
+		return -ENOMEM;
+	}
+
+	pm_set_ops(&pxa_pm_ops);
+	return 0;
+}
+
+device_initcall(pxa_pm_init);
diff --git a/arch/arm/mach-pxa/pxa25x.c b/arch/arm/mach-pxa/pxa25x.c
index f36ca44..6dfcca7 100644
--- a/arch/arm/mach-pxa/pxa25x.c
+++ b/arch/arm/mach-pxa/pxa25x.c
@@ -110,26 +110,99 @@
 
 #ifdef CONFIG_PM
 
-void pxa_cpu_pm_enter(suspend_state_t state)
-{
-	extern void pxa_cpu_suspend(unsigned int);
-	extern void pxa_cpu_resume(void);
+#define SAVE(x)		sleep_save[SLEEP_SAVE_##x] = x
+#define RESTORE(x)	x = sleep_save[SLEEP_SAVE_##x]
 
+#define RESTORE_GPLEVEL(n) do { \
+	GPSR##n = sleep_save[SLEEP_SAVE_GPLR##n]; \
+	GPCR##n = ~sleep_save[SLEEP_SAVE_GPLR##n]; \
+} while (0)
+
+/*
+ * List of global PXA peripheral registers to preserve.
+ * More ones like CP and general purpose register values are preserved
+ * with the stack pointer in sleep.S.
+ */
+enum {	SLEEP_SAVE_START = 0,
+
+	SLEEP_SAVE_GPLR0, SLEEP_SAVE_GPLR1, SLEEP_SAVE_GPLR2,
+	SLEEP_SAVE_GPDR0, SLEEP_SAVE_GPDR1, SLEEP_SAVE_GPDR2,
+	SLEEP_SAVE_GRER0, SLEEP_SAVE_GRER1, SLEEP_SAVE_GRER2,
+	SLEEP_SAVE_GFER0, SLEEP_SAVE_GFER1, SLEEP_SAVE_GFER2,
+	SLEEP_SAVE_PGSR0, SLEEP_SAVE_PGSR1, SLEEP_SAVE_PGSR2,
+
+	SLEEP_SAVE_GAFR0_L, SLEEP_SAVE_GAFR0_U,
+	SLEEP_SAVE_GAFR1_L, SLEEP_SAVE_GAFR1_U,
+	SLEEP_SAVE_GAFR2_L, SLEEP_SAVE_GAFR2_U,
+
+	SLEEP_SAVE_PSTR,
+
+	SLEEP_SAVE_ICMR,
+	SLEEP_SAVE_CKEN,
+
+	SLEEP_SAVE_SIZE
+};
+
+
+static void pxa25x_cpu_pm_save(unsigned long *sleep_save)
+{
+	SAVE(GPLR0); SAVE(GPLR1); SAVE(GPLR2);
+	SAVE(GPDR0); SAVE(GPDR1); SAVE(GPDR2);
+	SAVE(GRER0); SAVE(GRER1); SAVE(GRER2);
+	SAVE(GFER0); SAVE(GFER1); SAVE(GFER2);
+	SAVE(PGSR0); SAVE(PGSR1); SAVE(PGSR2);
+
+	SAVE(GAFR0_L); SAVE(GAFR0_U);
+	SAVE(GAFR1_L); SAVE(GAFR1_U);
+	SAVE(GAFR2_L); SAVE(GAFR2_U);
+
+	SAVE(ICMR);
+	SAVE(CKEN);
+	SAVE(PSTR);
+}
+
+static void pxa25x_cpu_pm_restore(unsigned long *sleep_save)
+{
+	/* restore registers */
+	RESTORE_GPLEVEL(0); RESTORE_GPLEVEL(1); RESTORE_GPLEVEL(2);
+	RESTORE(GPDR0); RESTORE(GPDR1); RESTORE(GPDR2);
+	RESTORE(GAFR0_L); RESTORE(GAFR0_U);
+	RESTORE(GAFR1_L); RESTORE(GAFR1_U);
+	RESTORE(GAFR2_L); RESTORE(GAFR2_U);
+	RESTORE(GRER0); RESTORE(GRER1); RESTORE(GRER2);
+	RESTORE(GFER0); RESTORE(GFER1); RESTORE(GFER2);
+	RESTORE(PGSR0); RESTORE(PGSR1); RESTORE(PGSR2);
+
+	RESTORE(CKEN);
+	RESTORE(ICMR);
+	RESTORE(PSTR);
+}
+
+static void pxa25x_cpu_pm_enter(suspend_state_t state)
+{
 	CKEN = 0;
 
 	switch (state) {
 	case PM_SUSPEND_MEM:
 		/* set resume return address */
 		PSPR = virt_to_phys(pxa_cpu_resume);
-		pxa_cpu_suspend(PWRMODE_SLEEP);
+		pxa25x_cpu_suspend(PWRMODE_SLEEP);
 		break;
 	}
 }
 
-static struct pm_ops pxa25x_pm_ops = {
-	.enter		= pxa_pm_enter,
+static struct pxa_cpu_pm_fns pxa25x_cpu_pm_fns = {
+	.save_size	= SLEEP_SAVE_SIZE,
 	.valid		= pm_valid_only_mem,
+	.save		= pxa25x_cpu_pm_save,
+	.restore	= pxa25x_cpu_pm_restore,
+	.enter		= pxa25x_cpu_pm_enter,
 };
+
+static void __init pxa25x_init_pm(void)
+{
+	pxa_cpu_pm_fns = &pxa25x_cpu_pm_fns;
+}
 #endif
 
 void __init pxa25x_init_irq(void)
@@ -139,16 +212,16 @@
 }
 
 static struct platform_device *pxa25x_devices[] __initdata = {
-	&pxamci_device,
-	&pxaudc_device,
-	&pxafb_device,
-	&ffuart_device,
-	&btuart_device,
-	&stuart_device,
-	&pxai2c_device,
-	&pxai2s_device,
-	&pxaficp_device,
-	&pxartc_device,
+	&pxa_device_mci,
+	&pxa_device_udc,
+	&pxa_device_fb,
+	&pxa_device_ffuart,
+	&pxa_device_btuart,
+	&pxa_device_stuart,
+	&pxa_device_i2c,
+	&pxa_device_i2s,
+	&pxa_device_ficp,
+	&pxa_device_rtc,
 };
 
 static int __init pxa25x_init(void)
@@ -159,14 +232,14 @@
 		if ((ret = pxa_init_dma(16)))
 			return ret;
 #ifdef CONFIG_PM
-		pm_set_ops(&pxa25x_pm_ops);
+		pxa25x_init_pm();
 #endif
 		ret = platform_add_devices(pxa25x_devices,
 					   ARRAY_SIZE(pxa25x_devices));
 	}
 	/* Only add HWUART for PXA255/26x; PXA210/250/27x do not have it. */
 	if (cpu_is_pxa25x())
-		ret = platform_device_register(&hwuart_device);
+		ret = platform_device_register(&pxa_device_hwuart);
 
 	return ret;
 }
diff --git a/arch/arm/mach-pxa/pxa27x.c b/arch/arm/mach-pxa/pxa27x.c
index aa5bb02..203371a 100644
--- a/arch/arm/mach-pxa/pxa27x.c
+++ b/arch/arm/mach-pxa/pxa27x.c
@@ -126,14 +126,107 @@
 
 #ifdef CONFIG_PM
 
-void pxa_cpu_pm_enter(suspend_state_t state)
+#define SAVE(x)		sleep_save[SLEEP_SAVE_##x] = x
+#define RESTORE(x)	x = sleep_save[SLEEP_SAVE_##x]
+
+#define RESTORE_GPLEVEL(n) do { \
+	GPSR##n = sleep_save[SLEEP_SAVE_GPLR##n]; \
+	GPCR##n = ~sleep_save[SLEEP_SAVE_GPLR##n]; \
+} while (0)
+
+/*
+ * List of global PXA peripheral registers to preserve.
+ * More ones like CP and general purpose register values are preserved
+ * with the stack pointer in sleep.S.
+ */
+enum {	SLEEP_SAVE_START = 0,
+
+	SLEEP_SAVE_GPLR0, SLEEP_SAVE_GPLR1, SLEEP_SAVE_GPLR2, SLEEP_SAVE_GPLR3,
+	SLEEP_SAVE_GPDR0, SLEEP_SAVE_GPDR1, SLEEP_SAVE_GPDR2, SLEEP_SAVE_GPDR3,
+	SLEEP_SAVE_GRER0, SLEEP_SAVE_GRER1, SLEEP_SAVE_GRER2, SLEEP_SAVE_GRER3,
+	SLEEP_SAVE_GFER0, SLEEP_SAVE_GFER1, SLEEP_SAVE_GFER2, SLEEP_SAVE_GFER3,
+	SLEEP_SAVE_PGSR0, SLEEP_SAVE_PGSR1, SLEEP_SAVE_PGSR2, SLEEP_SAVE_PGSR3,
+
+	SLEEP_SAVE_GAFR0_L, SLEEP_SAVE_GAFR0_U,
+	SLEEP_SAVE_GAFR1_L, SLEEP_SAVE_GAFR1_U,
+	SLEEP_SAVE_GAFR2_L, SLEEP_SAVE_GAFR2_U,
+	SLEEP_SAVE_GAFR3_L, SLEEP_SAVE_GAFR3_U,
+
+	SLEEP_SAVE_PSTR,
+
+	SLEEP_SAVE_ICMR,
+	SLEEP_SAVE_CKEN,
+
+	SLEEP_SAVE_MDREFR,
+	SLEEP_SAVE_PWER, SLEEP_SAVE_PCFR, SLEEP_SAVE_PRER,
+	SLEEP_SAVE_PFER, SLEEP_SAVE_PKWR,
+
+	SLEEP_SAVE_SIZE
+};
+
+void pxa27x_cpu_pm_save(unsigned long *sleep_save)
+{
+	SAVE(GPLR0); SAVE(GPLR1); SAVE(GPLR2); SAVE(GPLR3);
+	SAVE(GPDR0); SAVE(GPDR1); SAVE(GPDR2); SAVE(GPDR3);
+	SAVE(GRER0); SAVE(GRER1); SAVE(GRER2); SAVE(GRER3);
+	SAVE(GFER0); SAVE(GFER1); SAVE(GFER2); SAVE(GFER3);
+	SAVE(PGSR0); SAVE(PGSR1); SAVE(PGSR2); SAVE(PGSR3);
+
+	SAVE(GAFR0_L); SAVE(GAFR0_U);
+	SAVE(GAFR1_L); SAVE(GAFR1_U);
+	SAVE(GAFR2_L); SAVE(GAFR2_U);
+	SAVE(GAFR3_L); SAVE(GAFR3_U);
+
+	SAVE(MDREFR);
+	SAVE(PWER); SAVE(PCFR); SAVE(PRER);
+	SAVE(PFER); SAVE(PKWR);
+
+	SAVE(ICMR); ICMR = 0;
+	SAVE(CKEN);
+	SAVE(PSTR);
+
+	/* Clear GPIO transition detect bits */
+	GEDR0 = GEDR0; GEDR1 = GEDR1; GEDR2 = GEDR2; GEDR3 = GEDR3;
+}
+
+void pxa27x_cpu_pm_restore(unsigned long *sleep_save)
+{
+	/* ensure not to come back here if it wasn't intended */
+	PSPR = 0;
+
+	/* restore registers */
+	RESTORE_GPLEVEL(0); RESTORE_GPLEVEL(1);
+	RESTORE_GPLEVEL(2); RESTORE_GPLEVEL(3);
+	RESTORE(GPDR0); RESTORE(GPDR1); RESTORE(GPDR2); RESTORE(GPDR3);
+	RESTORE(GAFR0_L); RESTORE(GAFR0_U);
+	RESTORE(GAFR1_L); RESTORE(GAFR1_U);
+	RESTORE(GAFR2_L); RESTORE(GAFR2_U);
+	RESTORE(GAFR3_L); RESTORE(GAFR3_U);
+	RESTORE(GRER0); RESTORE(GRER1); RESTORE(GRER2); RESTORE(GRER3);
+	RESTORE(GFER0); RESTORE(GFER1); RESTORE(GFER2); RESTORE(GFER3);
+	RESTORE(PGSR0); RESTORE(PGSR1); RESTORE(PGSR2); RESTORE(PGSR3);
+
+	RESTORE(MDREFR);
+	RESTORE(PWER); RESTORE(PCFR); RESTORE(PRER);
+	RESTORE(PFER); RESTORE(PKWR);
+
+	PSSR = PSSR_RDH | PSSR_PH;
+
+	RESTORE(CKEN);
+
+	ICLR = 0;
+	ICCR = 1;
+	RESTORE(ICMR);
+	RESTORE(PSTR);
+}
+
+void pxa27x_cpu_pm_enter(suspend_state_t state)
 {
 	extern void pxa_cpu_standby(void);
-	extern void pxa_cpu_suspend(unsigned int);
-	extern void pxa_cpu_resume(void);
 
 	if (state == PM_SUSPEND_STANDBY)
-		CKEN = (1 << CKEN_MEMC) | (1 << CKEN_OSTIMER) | (1 << CKEN_LCD) | (1 << CKEN_PWM0);
+		CKEN = (1 << CKEN_MEMC) | (1 << CKEN_OSTIMER) |
+			(1 << CKEN_LCD) | (1 << CKEN_PWM0);
 	else
 		CKEN = (1 << CKEN_MEMC) | (1 << CKEN_OSTIMER);
 
@@ -150,20 +243,28 @@
 	case PM_SUSPEND_MEM:
 		/* set resume return address */
 		PSPR = virt_to_phys(pxa_cpu_resume);
-		pxa_cpu_suspend(PWRMODE_SLEEP);
+		pxa27x_cpu_suspend(PWRMODE_SLEEP);
 		break;
 	}
 }
 
-static int pxa27x_pm_valid(suspend_state_t state)
+static int pxa27x_cpu_pm_valid(suspend_state_t state)
 {
 	return state == PM_SUSPEND_MEM || state == PM_SUSPEND_STANDBY;
 }
 
-static struct pm_ops pxa27x_pm_ops = {
-	.enter		= pxa_pm_enter,
-	.valid		= pxa27x_pm_valid,
+static struct pxa_cpu_pm_fns pxa27x_cpu_pm_fns = {
+	.save_size	= SLEEP_SAVE_SIZE,
+	.save		= pxa27x_cpu_pm_save,
+	.restore	= pxa27x_cpu_pm_restore,
+	.valid		= pxa27x_cpu_pm_valid,
+	.enter		= pxa27x_cpu_pm_enter,
 };
+
+static void __init pxa27x_init_pm(void)
+{
+	pxa_cpu_pm_fns = &pxa27x_cpu_pm_fns;
+}
 #endif
 
 /*
@@ -185,7 +286,7 @@
 	},
 };
 
-static struct platform_device pxaohci_device = {
+static struct platform_device pxa27x_device_ohci = {
 	.name		= "pxa27x-ohci",
 	.id		= -1,
 	.dev		= {
@@ -198,7 +299,7 @@
 
 void __init pxa_set_ohci_info(struct pxaohci_platform_data *info)
 {
-	pxaohci_device.dev.platform_data = info;
+	pxa27x_device_ohci.dev.platform_data = info;
 }
 
 static struct resource i2c_power_resources[] = {
@@ -213,7 +314,7 @@
 	},
 };
 
-static struct platform_device pxai2c_power_device = {
+static struct platform_device pxa27x_device_i2c_power = {
 	.name		= "pxa2xx-i2c",
 	.id		= 1,
 	.resource	= i2c_power_resources,
@@ -221,18 +322,18 @@
 };
 
 static struct platform_device *devices[] __initdata = {
-	&pxamci_device,
-	&pxaudc_device,
-	&pxafb_device,
-	&ffuart_device,
-	&btuart_device,
-	&stuart_device,
-	&pxai2c_device,
-	&pxai2c_power_device,
-	&pxai2s_device,
-	&pxaficp_device,
-	&pxartc_device,
-	&pxaohci_device,
+	&pxa_device_mci,
+	&pxa_device_udc,
+	&pxa_device_fb,
+	&pxa_device_ffuart,
+	&pxa_device_btuart,
+	&pxa_device_stuart,
+	&pxa_device_i2c,
+	&pxa_device_i2s,
+	&pxa_device_ficp,
+	&pxa_device_rtc,
+	&pxa27x_device_i2c_power,
+	&pxa27x_device_ohci,
 };
 
 void __init pxa27x_init_irq(void)
@@ -249,7 +350,7 @@
 		if ((ret = pxa_init_dma(32)))
 			return ret;
 #ifdef CONFIG_PM
-		pm_set_ops(&pxa27x_pm_ops);
+		pxa27x_init_pm();
 #endif
 		ret = platform_add_devices(devices, ARRAY_SIZE(devices));
 	}
diff --git a/arch/arm/mach-pxa/sleep.S b/arch/arm/mach-pxa/sleep.S
index 15874b3..aff71fe 100644
--- a/arch/arm/mach-pxa/sleep.S
+++ b/arch/arm/mach-pxa/sleep.S
@@ -17,28 +17,12 @@
 
 #include <asm/arch/pxa-regs.h>
 
-#ifdef CONFIG_PXA27x			// workaround for Errata 50
 #define MDREFR_KDIV	0x200a4000	// all banks
 #define CCCR_SLEEP	0x00000107	// L=7 2N=2 A=0 PPDIS=0 CPDIS=0
-#endif
 
 		.text
 
-/*
- * pxa_cpu_suspend()
- *
- * Forces CPU into sleep state.
- *
- * r0 = value for PWRMODE M field for desired sleep state
- */
-
-ENTRY(pxa_cpu_suspend)
-
-#ifndef CONFIG_IWMMXT
-	mra	r2, r3, acc0
-#endif
-	stmfd	sp!, {r2 - r12, lr}		@ save registers on stack
-
+pxa_cpu_save_cp:
 	@ get coprocessor registers
 	mrc	p14, 0, r3, c6, c0, 0		@ clock configuration, for turbo mode
 	mrc	p15, 0, r4, c15, c1, 0		@ CP access reg
@@ -54,12 +38,36 @@
 	mov	r10, sp
 	stmfd	sp!, {r3 - r10}
 
-	mov r5, r0				@ save sleep mode
+	mov	pc, lr
+
+pxa_cpu_save_sp:
 	@ preserve phys address of stack
 	mov	r0, sp
+	mov	r2, lr
 	bl	sleep_phys_sp
 	ldr	r1, =sleep_save_sp
 	str	r0, [r1]
+	mov	pc, r2
+
+/*
+ * pxa27x_cpu_suspend()
+ *
+ * Forces CPU into sleep state.
+ *
+ * r0 = value for PWRMODE M field for desired sleep state
+ */
+
+ENTRY(pxa27x_cpu_suspend)
+
+#ifndef CONFIG_IWMMXT
+	mra	r2, r3, acc0
+#endif
+	stmfd	sp!, {r2 - r12, lr}		@ save registers on stack
+
+	bl	pxa_cpu_save_cp
+
+	mov	r5, r0				@ save sleep mode
+	bl	pxa_cpu_save_sp
 
 	@ clean data cache
 	bl	xscale_flush_kern_cache_all
@@ -80,13 +88,55 @@
 	@ enable SDRAM self-refresh mode
 	orr	r5, r5, #MDREFR_SLFRSH
 
-#ifdef CONFIG_PXA27x
 	@ set SDCLKx divide-by-2 bits (this is part of a workaround for Errata 50)
 	ldr	r6, =MDREFR_KDIV
 	orr	r5, r5, r6
-#endif
 
-#ifdef CONFIG_PXA25x
+	@ Intel PXA270 Specification Update notes problems sleeping
+	@ with core operating above 91 MHz
+	@ (see Errata 50, ...processor does not exit from sleep...)
+
+	ldr	r6, =CCCR
+	ldr	r8, [r6]		@ keep original value for resume
+
+	ldr	r7, =CCCR_SLEEP		@ prepare CCCR sleep value
+	mov	r0, #0x2		@ prepare value for CLKCFG
+
+	@ align execution to a cache line
+	b	pxa_cpu_do_suspend
+
+/*
+ * pxa27x_cpu_suspend()
+ *
+ * Forces CPU into sleep state.
+ *
+ * r0 = value for PWRMODE M field for desired sleep state
+ */
+
+ENTRY(pxa25x_cpu_suspend)
+	stmfd	sp!, {r2 - r12, lr}		@ save registers on stack
+
+	bl	pxa_cpu_save_cp
+
+	mov	r5, r0				@ save sleep mode
+	bl	pxa_cpu_save_sp
+
+	@ clean data cache
+	bl	xscale_flush_kern_cache_all
+
+	@ prepare value for sleep mode
+	mov	r1, r5				@ sleep mode
+
+	@ prepare pointer to physical address 0 (virtual mapping in generic.c)
+	mov	r2, #UNCACHED_PHYS_0
+
+	@ prepare SDRAM refresh settings
+	ldr	r4, =MDREFR
+	ldr	r5, [r4]
+
+	@ enable SDRAM self-refresh mode
+	orr	r5, r5, #MDREFR_SLFRSH
+
 	@ Intel PXA255 Specification Update notes problems
 	@ about suspending with PXBus operating above 133MHz
 	@ (see Errata 31, GPIO output signals, ... unpredictable in sleep
@@ -118,30 +168,15 @@
 	mov	r0, #0
 	mcr	p14, 0, r0, c6, c0, 0
 	orr	r0, r0, #2			@ initiate change bit
-#endif
-#ifdef CONFIG_PXA27x
-	@ Intel PXA270 Specification Update notes problems sleeping
-	@ with core operating above 91 MHz
-	@ (see Errata 50, ...processor does not exit from sleep...)
-
-	ldr	r6, =CCCR
-	ldr	r8, [r6]		@ keep original value for resume
-
-	ldr	r7, =CCCR_SLEEP		@ prepare CCCR sleep value
-	mov	r0, #0x2		@ prepare value for CLKCFG
-#endif
-
-	@ align execution to a cache line
-	b	1f
+	b	pxa_cpu_do_suspend
 
 	.ltorg
 	.align	5
-1:
+pxa_cpu_do_suspend:
 
 	@ All needed values are now in registers.
 	@ These last instructions should be in cache
 
-#if defined(CONFIG_PXA25x) || defined(CONFIG_PXA27x)
 	@ initiate the frequency change...
 	str	r7, [r6]
 	mcr	p14, 0, r0, c6, c0, 0
@@ -155,7 +190,6 @@
 	mov	r0, #42
 10:	subs	r0, r0, #1
 	bne	10b
-#endif
 
 	@ Do not reorder...
 	@ Intel PXA270 Specification Update notes problems performing
diff --git a/arch/arm/mach-pxa/time.c b/arch/arm/mach-pxa/time.c
index 6f91fd2..98d27e6 100644
--- a/arch/arm/mach-pxa/time.c
+++ b/arch/arm/mach-pxa/time.c
@@ -1,9 +1,11 @@
 /*
  * arch/arm/mach-pxa/time.c
  *
- * Author:	Nicolas Pitre
- * Created:	Jun 15, 2001
- * Copyright:	MontaVista Software Inc.
+ * PXA clocksource, clockevents, and OST interrupt handlers.
+ * Copyright (c) 2007 by Bill Gatliff <bgat@billgatliff.com>.
+ *
+ * Derived from Nicolas Pitre's PXA timer handler Copyright (c) 2001
+ * by MontaVista Software, Inc.  (Nico, your code rocks!)
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
@@ -12,164 +14,160 @@
 
 #include <linux/kernel.h>
 #include <linux/init.h>
-#include <linux/delay.h>
 #include <linux/interrupt.h>
-#include <linux/time.h>
-#include <linux/signal.h>
-#include <linux/errno.h>
-#include <linux/sched.h>
-#include <linux/clocksource.h>
+#include <linux/clockchips.h>
 
-#include <asm/system.h>
-#include <asm/hardware.h>
-#include <asm/io.h>
-#include <asm/leds.h>
-#include <asm/irq.h>
 #include <asm/mach/irq.h>
 #include <asm/mach/time.h>
 #include <asm/arch/pxa-regs.h>
 
-
-static int pxa_set_rtc(void)
-{
-	unsigned long current_time = xtime.tv_sec;
-
-	if (RTSR & RTSR_ALE) {
-		/* make sure not to forward the clock over an alarm */
-		unsigned long alarm = RTAR;
-		if (current_time >= alarm && alarm >= RCNR)
-			return -ERESTARTSYS;
-	}
-	RCNR = current_time;
-	return 0;
-}
-
-#ifdef CONFIG_NO_IDLE_HZ
-static unsigned long initial_match;
-static int match_posponed;
-#endif
-
 static irqreturn_t
-pxa_timer_interrupt(int irq, void *dev_id)
+pxa_ost0_interrupt(int irq, void *dev_id)
 {
 	int next_match;
+	struct clock_event_device *c = dev_id;
 
-	write_seqlock(&xtime_lock);
-
-#ifdef CONFIG_NO_IDLE_HZ
-	if (match_posponed) {
-		match_posponed = 0;
-		OSMR0 = initial_match;
-	}
-#endif
-
-	/* Loop until we get ahead of the free running timer.
-	 * This ensures an exact clock tick count and time accuracy.
-	 * Since IRQs are disabled at this point, coherence between
-	 * lost_ticks(updated in do_timer()) and the match reg value is
-	 * ensured, hence we can use do_gettimeofday() from interrupt
-	 * handlers.
-	 *
-	 * HACK ALERT: it seems that the PXA timer regs aren't updated right
-	 * away in all cases when a write occurs.  We therefore compare with
-	 * 8 instead of 0 in the while() condition below to avoid missing a
-	 * match if OSCR has already reached the next OSMR value.
-	 * Experience has shown that up to 6 ticks are needed to work around
-	 * this problem, but let's use 8 to be conservative.  Note that this
-	 * affect things only when the timer IRQ has been delayed by nearly
-	 * exactly one tick period which should be a pretty rare event.
+	if (c->mode == CLOCK_EVT_MODE_ONESHOT) {
+		/* Disarm the compare/match, signal the event. */
+		OIER &= ~OIER_E0;
+		c->event_handler(c);
+	} else if (c->mode == CLOCK_EVT_MODE_PERIODIC) {
+		/* Call the event handler as many times as necessary
+		 * to recover missed events, if any (if we update
+		 * OSMR0 and OSCR0 is still ahead of us, we've missed
+		 * the event).  As we're dealing with that, re-arm the
+		 * compare/match for the next event.
+		 *
+		 * HACK ALERT:
+		 *
+		 * There's a latency between the instruction that
+		 * writes to OSMR0 and the actual commit to the
+		 * physical hardware, because the CPU doesn't (have
+		 * to) run at bus speed, there's a write buffer
+		 * between the CPU and the bus, etc. etc.  So if the
+		 * target OSCR0 is "very close", to the OSMR0 load
+		 * value, the update to OSMR0 might not get to the
+		 * hardware in time and we'll miss that interrupt.
+		 *
+		 * To be safe, if the new OSMR0 is "very close" to the
+		 * target OSCR0 value, we call the event_handler as
+		 * though the event actually happened.  According to
+		 * Nico's comment in the previous version of this
+		 * code, experience has shown that 6 OSCR ticks is
+		 * "very close" but he went with 8.  We will use 16,
+		 * based on the results of testing on PXA270.
+		 *
+		 * To be doubly sure, we also tell clkevt via
+		 * clockevents_register_device() not to ask for
+		 * anything that might put us "very close".
 	 */
+#define MIN_OSCR_DELTA 16
 	do {
-		timer_tick();
-		OSSR = OSSR_M0;  /* Clear match on timer 0 */
+			OSSR = OSSR_M0;
 		next_match = (OSMR0 += LATCH);
-	} while( (signed long)(next_match - OSCR) <= 8 );
-
-	write_sequnlock(&xtime_lock);
+			c->event_handler(c);
+		} while (((signed long)(next_match - OSCR) <= MIN_OSCR_DELTA)
+			 && (c->mode == CLOCK_EVT_MODE_PERIODIC));
+	}
 
 	return IRQ_HANDLED;
 }
 
-static struct irqaction pxa_timer_irq = {
-	.name		= "PXA Timer Tick",
-	.flags		= IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL,
-	.handler	= pxa_timer_interrupt,
+static int
+pxa_osmr0_set_next_event(unsigned long delta, struct clock_event_device *dev)
+{
+	unsigned long irqflags;
+
+	raw_local_irq_save(irqflags);
+	OSMR0 = OSCR + delta;
+	OSSR = OSSR_M0;
+	OIER |= OIER_E0;
+	raw_local_irq_restore(irqflags);
+	return 0;
+}
+
+static void
+pxa_osmr0_set_mode(enum clock_event_mode mode, struct clock_event_device *dev)
+{
+	unsigned long irqflags;
+
+	switch (mode) {
+	case CLOCK_EVT_MODE_PERIODIC:
+		raw_local_irq_save(irqflags);
+		OSMR0 = OSCR + LATCH;
+		OSSR = OSSR_M0;
+		OIER |= OIER_E0;
+		raw_local_irq_restore(irqflags);
+		break;
+
+	case CLOCK_EVT_MODE_ONESHOT:
+		raw_local_irq_save(irqflags);
+		OIER &= ~OIER_E0;
+		raw_local_irq_restore(irqflags);
+		break;
+
+	case CLOCK_EVT_MODE_UNUSED:
+	case CLOCK_EVT_MODE_SHUTDOWN:
+		/* initializing, released, or preparing for suspend */
+		raw_local_irq_save(irqflags);
+		OIER &= ~OIER_E0;
+		raw_local_irq_restore(irqflags);
+		break;
+	}
+}
+
+static struct clock_event_device ckevt_pxa_osmr0 = {
+	.name		= "osmr0",
+	.features	= CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT,
+	.shift		= 32,
+	.rating		= 200,
+	.cpumask	= CPU_MASK_CPU0,
+	.set_next_event	= pxa_osmr0_set_next_event,
+	.set_mode	= pxa_osmr0_set_mode,
 };
 
-static cycle_t pxa_get_cycles(void)
+static cycle_t pxa_read_oscr(void)
 {
 	return OSCR;
 }
 
-static struct clocksource clocksource_pxa = {
-	.name           = "pxa_timer",
+static struct clocksource cksrc_pxa_oscr0 = {
+	.name           = "oscr0",
 	.rating         = 200,
-	.read           = pxa_get_cycles,
+	.read           = pxa_read_oscr,
 	.mask           = CLOCKSOURCE_MASK(32),
 	.shift          = 20,
 	.flags		= CLOCK_SOURCE_IS_CONTINUOUS,
 };
 
+static struct irqaction pxa_ost0_irq = {
+	.name		= "ost0",
+	.flags		= IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL,
+	.handler	= pxa_ost0_interrupt,
+	.dev_id		= &ckevt_pxa_osmr0,
+};
+
 static void __init pxa_timer_init(void)
 {
-	struct timespec tv;
-	unsigned long flags;
+	OIER = 0;
+	OSSR = OSSR_M0 | OSSR_M1 | OSSR_M2 | OSSR_M3;
 
-	set_rtc = pxa_set_rtc;
+	ckevt_pxa_osmr0.mult =
+		div_sc(CLOCK_TICK_RATE, NSEC_PER_SEC, ckevt_pxa_osmr0.shift);
+	ckevt_pxa_osmr0.max_delta_ns =
+		clockevent_delta2ns(0x7fffffff, &ckevt_pxa_osmr0);
+	ckevt_pxa_osmr0.min_delta_ns =
+		clockevent_delta2ns(MIN_OSCR_DELTA, &ckevt_pxa_osmr0) + 1;
 
-	OIER = 0;		/* disable any timer interrupts */
-	OSSR = 0xf;		/* clear status on all timers */
-	setup_irq(IRQ_OST0, &pxa_timer_irq);
-	local_irq_save(flags);
-	OIER = OIER_E0;		/* enable match on timer 0 to cause interrupts */
-	OSMR0 = OSCR + LATCH;	/* set initial match */
-	local_irq_restore(flags);
+	cksrc_pxa_oscr0.mult =
+		clocksource_hz2mult(CLOCK_TICK_RATE, cksrc_pxa_oscr0.shift);
 
-	/*
-	 * OSCR runs continuously on PXA and is not written to,
-	 * so we can use it as clock source directly.
-	 */
-	clocksource_pxa.mult =
-		clocksource_hz2mult(CLOCK_TICK_RATE, clocksource_pxa.shift);
-	clocksource_register(&clocksource_pxa);
+	setup_irq(IRQ_OST0, &pxa_ost0_irq);
+
+	clocksource_register(&cksrc_pxa_oscr0);
+	clockevents_register_device(&ckevt_pxa_osmr0);
 }
 
-#ifdef CONFIG_NO_IDLE_HZ
-static int pxa_dyn_tick_enable_disable(void)
-{
-	/* nothing to do */
-	return 0;
-}
-
-static void pxa_dyn_tick_reprogram(unsigned long ticks)
-{
-	if (ticks > 1) {
-		initial_match = OSMR0;
-		OSMR0 = initial_match + ticks * LATCH;
-		match_posponed = 1;
-	}
-}
-
-static irqreturn_t
-pxa_dyn_tick_handler(int irq, void *dev_id)
-{
-	if (match_posponed) {
-		match_posponed = 0;
-		OSMR0 = initial_match;
-		if ( (signed long)(initial_match - OSCR) <= 8 )
-			return pxa_timer_interrupt(irq, dev_id);
-	}
-	return IRQ_NONE;
-}
-
-static struct dyn_tick_timer pxa_dyn_tick = {
-	.enable		= pxa_dyn_tick_enable_disable,
-	.disable	= pxa_dyn_tick_enable_disable,
-	.reprogram	= pxa_dyn_tick_reprogram,
-	.handler	= pxa_dyn_tick_handler,
-};
-#endif
-
 #ifdef CONFIG_PM
 static unsigned long osmr[4], oier;
 
@@ -191,7 +189,10 @@
 	OIER = oier;
 
 	/*
-	 * OSMR0 is the system timer: make sure OSCR is sufficiently behind
+	 * OSCR0 is the system timer, which has to increase
+	 * monotonically until it rolls over in hardware.  The value
+	 * (OSMR0 - LATCH) is OSCR0 at the most recent system tick,
+	 * which is a handy value to restore to OSCR0.
 	 */
 	OSCR = OSMR0 - LATCH;
 }
@@ -204,7 +205,4 @@
 	.init		= pxa_timer_init,
 	.suspend	= pxa_timer_suspend,
 	.resume		= pxa_timer_resume,
-#ifdef CONFIG_NO_IDLE_HZ
-	.dyn_tick	= &pxa_dyn_tick,
-#endif
 };
diff --git a/arch/arm/mach-rpc/riscpc.c b/arch/arm/mach-rpc/riscpc.c
index 570cf93..a454451 100644
--- a/arch/arm/mach-rpc/riscpc.c
+++ b/arch/arm/mach-rpc/riscpc.c
@@ -87,7 +87,7 @@
 	/*
 	 * Turn off floppy.
 	 */
-	outb(0xc, 0x3f2);
+	writeb(0xc, PCIO_BASE + (0x3f2 << 2));
 
 	/*
 	 * RiscPC can't handle half-word loads and stores
diff --git a/arch/arm/mach-s3c2410/Kconfig b/arch/arm/mach-s3c2410/Kconfig
index d4b013b..e2079cf 100644
--- a/arch/arm/mach-s3c2410/Kconfig
+++ b/arch/arm/mach-s3c2410/Kconfig
@@ -9,6 +9,7 @@
 	depends on ARCH_S3C2410
 	select S3C2410_CLOCK
 	select S3C2410_GPIO
+	select CPU_LLSERIAL_S3C2410
 	select S3C2410_PM if PM
 	help
 	  Support for S3C2410 and S3C2410A family from the S3C24XX line
diff --git a/arch/arm/mach-s3c2410/clock.c b/arch/arm/mach-s3c2410/clock.c
index 5b4831c..cab9d62 100644
--- a/arch/arm/mach-s3c2410/clock.c
+++ b/arch/arm/mach-s3c2410/clock.c
@@ -37,7 +37,7 @@
 #include <asm/hardware.h>
 #include <asm/io.h>
 
-#include <asm/arch/regs-serial.h>
+#include <asm/plat-s3c/regs-serial.h>
 #include <asm/arch/regs-clock.h>
 #include <asm/arch/regs-gpio.h>
 
diff --git a/arch/arm/mach-s3c2410/dma.c b/arch/arm/mach-s3c2410/dma.c
index 67d1ad3..80d8373 100644
--- a/arch/arm/mach-s3c2410/dma.c
+++ b/arch/arm/mach-s3c2410/dma.c
@@ -23,14 +23,14 @@
 #include <asm/plat-s3c24xx/cpu.h>
 #include <asm/plat-s3c24xx/dma.h>
 
-#include <asm/arch/regs-serial.h>
+#include <asm/plat-s3c/regs-serial.h>
 #include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-ac97.h>
+#include <asm/plat-s3c/regs-ac97.h>
 #include <asm/arch/regs-mem.h>
 #include <asm/arch/regs-lcd.h>
 #include <asm/arch/regs-sdi.h>
-#include <asm/arch/regs-iis.h>
-#include <asm/arch/regs-spi.h>
+#include <asm/plat-s3c24xx/regs-iis.h>
+#include <asm/plat-s3c24xx/regs-spi.h>
 
 static struct s3c24xx_dma_map __initdata s3c2410_dma_mappings[] = {
 	[DMACH_XD0] = {
diff --git a/arch/arm/mach-s3c2410/mach-amlm5900.c b/arch/arm/mach-s3c2410/mach-amlm5900.c
index 435adcc..43bb5e1 100644
--- a/arch/arm/mach-s3c2410/mach-amlm5900.c
+++ b/arch/arm/mach-s3c2410/mach-amlm5900.c
@@ -48,7 +48,7 @@
 #include <asm/mach-types.h>
 #include <asm/arch/fb.h>
 
-#include <asm/arch/regs-serial.h>
+#include <asm/plat-s3c/regs-serial.h>
 #include <asm/arch/regs-lcd.h>
 #include <asm/arch/regs-gpio.h>
 
diff --git a/arch/arm/mach-s3c2410/mach-bast.c b/arch/arm/mach-s3c2410/mach-bast.c
index 8b52ea9..bc92699 100644
--- a/arch/arm/mach-s3c2410/mach-bast.c
+++ b/arch/arm/mach-s3c2410/mach-bast.c
@@ -36,13 +36,13 @@
 #include <asm/mach-types.h>
 
 //#include <asm/debug-ll.h>
-#include <asm/arch/regs-serial.h>
+#include <asm/plat-s3c/regs-serial.h>
 #include <asm/arch/regs-gpio.h>
 #include <asm/arch/regs-mem.h>
 #include <asm/arch/regs-lcd.h>
 
-#include <asm/arch/nand.h>
-#include <asm/arch/iic.h>
+#include <asm/plat-s3c/nand.h>
+#include <asm/plat-s3c/iic.h>
 #include <asm/arch/fb.h>
 
 #include <linux/mtd/mtd.h>
diff --git a/arch/arm/mach-s3c2410/mach-h1940.c b/arch/arm/mach-s3c2410/mach-h1940.c
index 5c9bcea..9a172b4 100644
--- a/arch/arm/mach-s3c2410/mach-h1940.c
+++ b/arch/arm/mach-s3c2410/mach-h1940.c
@@ -30,7 +30,7 @@
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <asm/arch/regs-serial.h>
+#include <asm/plat-s3c/regs-serial.h>
 #include <asm/arch/regs-lcd.h>
 #include <asm/arch/regs-gpio.h>
 #include <asm/arch/regs-clock.h>
@@ -38,7 +38,7 @@
 #include <asm/arch/h1940.h>
 #include <asm/arch/h1940-latch.h>
 #include <asm/arch/fb.h>
-#include <asm/arch/udc.h>
+#include <asm/plat-s3c24xx/udc.h>
 
 #include <asm/plat-s3c24xx/clock.h>
 #include <asm/plat-s3c24xx/devs.h>
diff --git a/arch/arm/mach-s3c2410/mach-n30.c b/arch/arm/mach-s3c2410/mach-n30.c
index 412e50c..621f548 100644
--- a/arch/arm/mach-s3c2410/mach-n30.c
+++ b/arch/arm/mach-s3c2410/mach-n30.c
@@ -33,9 +33,9 @@
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <asm/arch/regs-serial.h>
+#include <asm/plat-s3c/regs-serial.h>
 #include <asm/arch/regs-gpio.h>
-#include <asm/arch/iic.h>
+#include <asm/plat-s3c/iic.h>
 
 #include <asm/plat-s3c24xx/s3c2410.h>
 #include <asm/plat-s3c24xx/clock.h>
diff --git a/arch/arm/mach-s3c2410/mach-otom.c b/arch/arm/mach-s3c2410/mach-otom.c
index 1f899fa..717af40 100644
--- a/arch/arm/mach-s3c2410/mach-otom.c
+++ b/arch/arm/mach-s3c2410/mach-otom.c
@@ -29,7 +29,7 @@
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <asm/arch/regs-serial.h>
+#include <asm/plat-s3c/regs-serial.h>
 #include <asm/arch/regs-gpio.h>
 
 #include <asm/plat-s3c24xx/s3c2410.h>
diff --git a/arch/arm/mach-s3c2410/mach-qt2410.c b/arch/arm/mach-s3c2410/mach-qt2410.c
index d86e6f1..e670b1e 100644
--- a/arch/arm/mach-s3c2410/mach-qt2410.c
+++ b/arch/arm/mach-s3c2410/mach-qt2410.c
@@ -49,10 +49,10 @@
 
 #include <asm/arch/regs-gpio.h>
 #include <asm/arch/leds-gpio.h>
-#include <asm/arch/regs-serial.h>
+#include <asm/plat-s3c/regs-serial.h>
 #include <asm/arch/fb.h>
-#include <asm/arch/nand.h>
-#include <asm/arch/udc.h>
+#include <asm/plat-s3c/nand.h>
+#include <asm/plat-s3c24xx/udc.h>
 #include <asm/arch/spi.h>
 #include <asm/arch/spi-gpio.h>
 
diff --git a/arch/arm/mach-s3c2410/mach-smdk2410.c b/arch/arm/mach-s3c2410/mach-smdk2410.c
index 5852d30..2265505 100644
--- a/arch/arm/mach-s3c2410/mach-smdk2410.c
+++ b/arch/arm/mach-s3c2410/mach-smdk2410.c
@@ -47,7 +47,7 @@
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <asm/arch/regs-serial.h>
+#include <asm/plat-s3c/regs-serial.h>
 
 #include <asm/plat-s3c24xx/devs.h>
 #include <asm/plat-s3c24xx/cpu.h>
diff --git a/arch/arm/mach-s3c2410/mach-vr1000.c b/arch/arm/mach-s3c2410/mach-vr1000.c
index 7b624bb..9f43f3f 100644
--- a/arch/arm/mach-s3c2410/mach-vr1000.c
+++ b/arch/arm/mach-s3c2410/mach-vr1000.c
@@ -39,7 +39,7 @@
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <asm/arch/regs-serial.h>
+#include <asm/plat-s3c/regs-serial.h>
 #include <asm/arch/regs-gpio.h>
 #include <asm/arch/leds-gpio.h>
 
diff --git a/arch/arm/mach-s3c2410/s3c2410.c b/arch/arm/mach-s3c2410/s3c2410.c
index 1a86a98..e580303 100644
--- a/arch/arm/mach-s3c2410/s3c2410.c
+++ b/arch/arm/mach-s3c2410/s3c2410.c
@@ -29,7 +29,7 @@
 #include <asm/irq.h>
 
 #include <asm/arch/regs-clock.h>
-#include <asm/arch/regs-serial.h>
+#include <asm/plat-s3c/regs-serial.h>
 
 #include <asm/plat-s3c24xx/s3c2410.h>
 #include <asm/plat-s3c24xx/cpu.h>
@@ -40,7 +40,6 @@
 
 static struct map_desc s3c2410_iodesc[] __initdata = {
 	IODESC_ENT(CLKPWR),
-	IODESC_ENT(LCD),
 	IODESC_ENT(TIMER),
 	IODESC_ENT(WATCHDOG),
 };
diff --git a/arch/arm/mach-s3c2410/sleep.S b/arch/arm/mach-s3c2410/sleep.S
index d1eeed2..8a9c5a2 100644
--- a/arch/arm/mach-s3c2410/sleep.S
+++ b/arch/arm/mach-s3c2410/sleep.S
@@ -32,7 +32,7 @@
 #include <asm/arch/regs-gpio.h>
 #include <asm/arch/regs-clock.h>
 #include <asm/arch/regs-mem.h>
-#include <asm/arch/regs-serial.h>
+#include <asm/plat-s3c/regs-serial.h>
 
 	/* s3c2410_cpu_suspend
 	 *
diff --git a/arch/arm/mach-s3c2412/Kconfig b/arch/arm/mach-s3c2412/Kconfig
index d5be5d0..8e8fe48 100644
--- a/arch/arm/mach-s3c2412/Kconfig
+++ b/arch/arm/mach-s3c2412/Kconfig
@@ -7,6 +7,7 @@
 config CPU_S3C2412
 	bool
 	depends on ARCH_S3C2410
+	select CPU_LLSERIAL_S3C2440
 	select S3C2412_PM if PM
 	select S3C2412_DMA if S3C2410_DMA
 	help
diff --git a/arch/arm/mach-s3c2412/clock.c b/arch/arm/mach-s3c2412/clock.c
index 6a8e444..8543dd6 100644
--- a/arch/arm/mach-s3c2412/clock.c
+++ b/arch/arm/mach-s3c2412/clock.c
@@ -37,7 +37,7 @@
 #include <asm/hardware.h>
 #include <asm/io.h>
 
-#include <asm/arch/regs-serial.h>
+#include <asm/plat-s3c/regs-serial.h>
 #include <asm/arch/regs-clock.h>
 #include <asm/arch/regs-gpio.h>
 
diff --git a/arch/arm/mach-s3c2412/dma.c b/arch/arm/mach-s3c2412/dma.c
index 668ccce..4b9425c 100644
--- a/arch/arm/mach-s3c2412/dma.c
+++ b/arch/arm/mach-s3c2412/dma.c
@@ -24,14 +24,14 @@
 #include <asm/plat-s3c24xx/dma.h>
 #include <asm/plat-s3c24xx/cpu.h>
 
-#include <asm/arch/regs-serial.h>
+#include <asm/plat-s3c/regs-serial.h>
 #include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-ac97.h>
+#include <asm/plat-s3c/regs-ac97.h>
 #include <asm/arch/regs-mem.h>
 #include <asm/arch/regs-lcd.h>
 #include <asm/arch/regs-sdi.h>
-#include <asm/arch/regs-iis.h>
-#include <asm/arch/regs-spi.h>
+#include <asm/plat-s3c24xx/regs-iis.h>
+#include <asm/plat-s3c24xx/regs-spi.h>
 
 #define MAP(x) { (x)| DMA_CH_VALID, (x)| DMA_CH_VALID, (x)| DMA_CH_VALID, (x)| DMA_CH_VALID }
 
diff --git a/arch/arm/mach-s3c2412/mach-smdk2413.c b/arch/arm/mach-s3c2412/mach-smdk2413.c
index 063af09..b126a53 100644
--- a/arch/arm/mach-s3c2412/mach-smdk2413.c
+++ b/arch/arm/mach-s3c2412/mach-smdk2413.c
@@ -32,12 +32,12 @@
 #include <asm/mach-types.h>
 
 //#include <asm/debug-ll.h>
-#include <asm/arch/regs-serial.h>
+#include <asm/plat-s3c/regs-serial.h>
 #include <asm/arch/regs-gpio.h>
 #include <asm/arch/regs-lcd.h>
 
 #include <asm/arch/idle.h>
-#include <asm/arch/udc.h>
+#include <asm/plat-s3c24xx/udc.h>
 #include <asm/arch/fb.h>
 
 #include <asm/plat-s3c24xx/s3c2410.h>
diff --git a/arch/arm/mach-s3c2412/mach-vstms.c b/arch/arm/mach-s3c2412/mach-vstms.c
index f2fbd65..3298254 100644
--- a/arch/arm/mach-s3c2412/mach-vstms.c
+++ b/arch/arm/mach-s3c2412/mach-vstms.c
@@ -33,14 +33,14 @@
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <asm/arch/regs-serial.h>
+#include <asm/plat-s3c/regs-serial.h>
 #include <asm/arch/regs-gpio.h>
 #include <asm/arch/regs-lcd.h>
 
 #include <asm/arch/idle.h>
 #include <asm/arch/fb.h>
 
-#include <asm/arch/nand.h>
+#include <asm/plat-s3c/nand.h>
 
 #include <asm/plat-s3c24xx/s3c2410.h>
 #include <asm/plat-s3c24xx/s3c2412.h>
diff --git a/arch/arm/mach-s3c2412/s3c2412.c b/arch/arm/mach-s3c2412/s3c2412.c
index 782b581..e0ccb40 100644
--- a/arch/arm/mach-s3c2412/s3c2412.c
+++ b/arch/arm/mach-s3c2412/s3c2412.c
@@ -34,12 +34,12 @@
 #include <asm/arch/idle.h>
 
 #include <asm/arch/regs-clock.h>
-#include <asm/arch/regs-serial.h>
+#include <asm/plat-s3c/regs-serial.h>
 #include <asm/arch/regs-power.h>
 #include <asm/arch/regs-gpio.h>
 #include <asm/arch/regs-gpioj.h>
 #include <asm/arch/regs-dsc.h>
-#include <asm/arch/regs-spi.h>
+#include <asm/plat-s3c24xx/regs-spi.h>
 #include <asm/arch/regs-s3c2412.h>
 
 #include <asm/plat-s3c24xx/s3c2412.h>
@@ -63,7 +63,6 @@
 
 static struct map_desc s3c2412_iodesc[] __initdata = {
 	IODESC_ENT(CLKPWR),
-	IODESC_ENT(LCD),
 	IODESC_ENT(TIMER),
 	IODESC_ENT(WATCHDOG),
 };
diff --git a/arch/arm/mach-s3c2440/Kconfig b/arch/arm/mach-s3c2440/Kconfig
index e3bfda0..f1915bd 100644
--- a/arch/arm/mach-s3c2440/Kconfig
+++ b/arch/arm/mach-s3c2440/Kconfig
@@ -12,6 +12,7 @@
 	select S3C2410_GPIO
 	select S3C2440_DMA if S3C2410_DMA
 	select CPU_S3C244X
+	select CPU_LLSERIAL_S3C2440
 	help
 	  Support for S3C2440 Samsung Mobile CPU based systems.
 
diff --git a/arch/arm/mach-s3c2440/dma.c b/arch/arm/mach-s3c2440/dma.c
index cd035a3..f509f06 100644
--- a/arch/arm/mach-s3c2440/dma.c
+++ b/arch/arm/mach-s3c2440/dma.c
@@ -23,14 +23,14 @@
 #include <asm/plat-s3c24xx/dma.h>
 #include <asm/plat-s3c24xx/cpu.h>
 
-#include <asm/arch/regs-serial.h>
+#include <asm/plat-s3c/regs-serial.h>
 #include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-ac97.h>
+#include <asm/plat-s3c/regs-ac97.h>
 #include <asm/arch/regs-mem.h>
 #include <asm/arch/regs-lcd.h>
 #include <asm/arch/regs-sdi.h>
-#include <asm/arch/regs-iis.h>
-#include <asm/arch/regs-spi.h>
+#include <asm/plat-s3c24xx/regs-iis.h>
+#include <asm/plat-s3c24xx/regs-spi.h>
 
 static struct s3c24xx_dma_map __initdata s3c2440_dma_mappings[] = {
 	[DMACH_XD0] = {
diff --git a/arch/arm/mach-s3c2440/mach-anubis.c b/arch/arm/mach-s3c2440/mach-anubis.c
index 29c163d..3d3dfa9 100644
--- a/arch/arm/mach-s3c2440/mach-anubis.c
+++ b/arch/arm/mach-s3c2440/mach-anubis.c
@@ -34,11 +34,11 @@
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <asm/arch/regs-serial.h>
+#include <asm/plat-s3c/regs-serial.h>
 #include <asm/arch/regs-gpio.h>
 #include <asm/arch/regs-mem.h>
 #include <asm/arch/regs-lcd.h>
-#include <asm/arch/nand.h>
+#include <asm/plat-s3c/nand.h>
 
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/nand.h>
diff --git a/arch/arm/mach-s3c2440/mach-nexcoder.c b/arch/arm/mach-s3c2440/mach-nexcoder.c
index 5e61f21..afe0d7b 100644
--- a/arch/arm/mach-s3c2440/mach-nexcoder.c
+++ b/arch/arm/mach-s3c2440/mach-nexcoder.c
@@ -36,7 +36,7 @@
 
 //#include <asm/debug-ll.h>
 #include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-serial.h>
+#include <asm/plat-s3c/regs-serial.h>
 
 #include <asm/plat-s3c24xx/s3c2410.h>
 #include <asm/plat-s3c24xx/s3c2440.h>
diff --git a/arch/arm/mach-s3c2440/mach-osiris.c b/arch/arm/mach-s3c2440/mach-osiris.c
index 89f4c9c..0ba7e90 100644
--- a/arch/arm/mach-s3c2440/mach-osiris.c
+++ b/arch/arm/mach-s3c2440/mach-osiris.c
@@ -31,11 +31,11 @@
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <asm/arch/regs-serial.h>
+#include <asm/plat-s3c/regs-serial.h>
 #include <asm/arch/regs-gpio.h>
 #include <asm/arch/regs-mem.h>
 #include <asm/arch/regs-lcd.h>
-#include <asm/arch/nand.h>
+#include <asm/plat-s3c/nand.h>
 
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/nand.h>
diff --git a/arch/arm/mach-s3c2440/mach-rx3715.c b/arch/arm/mach-s3c2440/mach-rx3715.c
index 866ff71..b59e6d3 100644
--- a/arch/arm/mach-s3c2440/mach-rx3715.c
+++ b/arch/arm/mach-s3c2440/mach-rx3715.c
@@ -38,12 +38,12 @@
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <asm/arch/regs-serial.h>
+#include <asm/plat-s3c/regs-serial.h>
 #include <asm/arch/regs-gpio.h>
 #include <asm/arch/regs-lcd.h>
 
 #include <asm/arch/h1940.h>
-#include <asm/arch/nand.h>
+#include <asm/plat-s3c/nand.h>
 #include <asm/arch/fb.h>
 
 #include <asm/plat-s3c24xx/clock.h>
diff --git a/arch/arm/mach-s3c2440/mach-smdk2440.c b/arch/arm/mach-s3c2440/mach-smdk2440.c
index e167254..670115b 100644
--- a/arch/arm/mach-s3c2440/mach-smdk2440.c
+++ b/arch/arm/mach-s3c2440/mach-smdk2440.c
@@ -31,7 +31,7 @@
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <asm/arch/regs-serial.h>
+#include <asm/plat-s3c/regs-serial.h>
 #include <asm/arch/regs-gpio.h>
 #include <asm/arch/regs-lcd.h>
 
diff --git a/arch/arm/mach-s3c2442/Kconfig b/arch/arm/mach-s3c2442/Kconfig
index bf8d87a..88d5fd3 100644
--- a/arch/arm/mach-s3c2442/Kconfig
+++ b/arch/arm/mach-s3c2442/Kconfig
@@ -11,6 +11,7 @@
 	select S3C2410_GPIO
 	select S3C2410_PM if PM
 	select CPU_S3C244X
+	select CPU_LLSERIAL_S3C2440
 	help
 	  Support for S3C2442 Samsung Mobile CPU based systems.
 
diff --git a/arch/arm/mach-s3c2443/Kconfig b/arch/arm/mach-s3c2443/Kconfig
index c649bb2..14252f5 100644
--- a/arch/arm/mach-s3c2443/Kconfig
+++ b/arch/arm/mach-s3c2443/Kconfig
@@ -8,6 +8,7 @@
 	bool
 	depends on ARCH_S3C2410
 	select S3C2443_DMA if S3C2410_DMA
+	select CPU_LLSERIAL_S3C2440
 	help
 	  Support for the S3C2443 SoC from the S3C24XX line
 
diff --git a/arch/arm/mach-s3c2443/dma.c b/arch/arm/mach-s3c2443/dma.c
index f70e8cc..fc3ede8 100644
--- a/arch/arm/mach-s3c2443/dma.c
+++ b/arch/arm/mach-s3c2443/dma.c
@@ -24,14 +24,14 @@
 #include <asm/plat-s3c24xx/dma.h>
 #include <asm/plat-s3c24xx/cpu.h>
 
-#include <asm/arch/regs-serial.h>
+#include <asm/plat-s3c/regs-serial.h>
 #include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-ac97.h>
+#include <asm/plat-s3c/regs-ac97.h>
 #include <asm/arch/regs-mem.h>
 #include <asm/arch/regs-lcd.h>
 #include <asm/arch/regs-sdi.h>
-#include <asm/arch/regs-iis.h>
-#include <asm/arch/regs-spi.h>
+#include <asm/plat-s3c24xx/regs-iis.h>
+#include <asm/plat-s3c24xx/regs-spi.h>
 
 #define MAP(x) { \
 		[0]	= (x) | DMA_CH_VALID,	\
diff --git a/arch/arm/mach-s3c2443/mach-smdk2443.c b/arch/arm/mach-s3c2443/mach-smdk2443.c
index b1eb709..8cd9313 100644
--- a/arch/arm/mach-s3c2443/mach-smdk2443.c
+++ b/arch/arm/mach-s3c2443/mach-smdk2443.c
@@ -31,7 +31,7 @@
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <asm/arch/regs-serial.h>
+#include <asm/plat-s3c/regs-serial.h>
 #include <asm/arch/regs-gpio.h>
 #include <asm/arch/regs-lcd.h>
 
diff --git a/arch/arm/mach-sa1100/Kconfig b/arch/arm/mach-sa1100/Kconfig
index cd67ab1..f99d901 100644
--- a/arch/arm/mach-sa1100/Kconfig
+++ b/arch/arm/mach-sa1100/Kconfig
@@ -101,6 +101,16 @@
 	  handheld computer.  See <http://www.hp.com/jornada/products/720>
 	  for details.
 
+config SA1100_JORNADA720_SSP
+	bool "HP Jornada 720 Extended SSP driver"
+	select SA1100_SSP
+	depends on SA1100_JORNADA720
+	help
+	  Say Y here if you have a HP Jornada 7xx handheld computer and you
+	  want to access devices connected to the MCU. Those include the
+	  keyboard, touchscreen, backlight and battery. This driver also activates
+	  the generic SSP which it extends.
+
 config SA1100_HACKKIT
 	bool "HackKit Core CPU Board"
 	help
@@ -145,8 +155,7 @@
 	help
 	  Say Y here to enable support for the generic PIO SSP driver.
 	  This isn't for audio support, but for attached sensors and
-	  other devices, eg for BadgePAD 4 sensor support, or Jornada
-	  720 touchscreen support.
+	  other devices, eg for BadgePAD 4 sensor support.
 
 config H3600_SLEEVE
 	tristate "Compaq iPAQ Handheld sleeve support"
diff --git a/arch/arm/mach-sa1100/Makefile b/arch/arm/mach-sa1100/Makefile
index e27f150..7a61e8d 100644
--- a/arch/arm/mach-sa1100/Makefile
+++ b/arch/arm/mach-sa1100/Makefile
@@ -31,6 +31,7 @@
 led-$(CONFIG_SA1100_HACKKIT)		+= leds-hackkit.o
 
 obj-$(CONFIG_SA1100_JORNADA720)		+= jornada720.o
+obj-$(CONFIG_SA1100_JORNADA720_SSP)	+= jornada720_ssp.o
 
 obj-$(CONFIG_SA1100_LART)		+= lart.o
 led-$(CONFIG_SA1100_LART)		+= leds-lart.o
@@ -51,3 +52,4 @@
 # Miscelaneous functions
 obj-$(CONFIG_PM)			+= pm.o sleep.o
 obj-$(CONFIG_SA1100_SSP)		+= ssp.o
+
diff --git a/arch/arm/mach-sa1100/jornada720_ssp.c b/arch/arm/mach-sa1100/jornada720_ssp.c
new file mode 100644
index 0000000..0a45e1a
--- /dev/null
+++ b/arch/arm/mach-sa1100/jornada720_ssp.c
@@ -0,0 +1,201 @@
+/**
+ *  arch/arm/mac-sa1100/jornada720_ssp.c
+ *
+ *  Copyright (C) 2006/2007 Kristoffer Ericson <Kristoffer.Ericson@gmail.com>
+ *   Copyright (C) 2006 Filip Zyzniewski <filip.zyzniewski@tefnet.pl>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ *  SSP driver for the HP Jornada 710/720/728
+ */
+
+#include <linux/delay.h>
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+
+#include <asm/hardware.h>
+#include <asm/hardware/ssp.h>
+#include <asm/arch/jornada720.h>
+
+static DEFINE_SPINLOCK(jornada_ssp_lock);
+static unsigned long jornada_ssp_flags;
+
+/**
+ * jornada_ssp_reverse - reverses input byte
+ *
+ * we need to reverse all data we recieve from the mcu due to its physical location
+ * returns : 01110111 -> 11101110
+ */
+u8 inline jornada_ssp_reverse(u8 byte)
+{
+	return
+		((0x80 & byte) >> 7) |
+		((0x40 & byte) >> 5) |
+		((0x20 & byte) >> 3) |
+		((0x10 & byte) >> 1) |
+		((0x08 & byte) << 1) |
+		((0x04 & byte) << 3) |
+		((0x02 & byte) << 5) |
+		((0x01 & byte) << 7);
+};
+EXPORT_SYMBOL(jornada_ssp_reverse);
+
+/**
+ * jornada_ssp_byte - waits for ready ssp bus and sends byte
+ *
+ * waits for fifo buffer to clear and then transmits, if it doesn't then we will
+ * timeout after <timeout> rounds. Needs mcu running before its called.
+ *
+ * returns : %mcu output on success
+ *	   : %-ETIMEOUT on timeout
+ */
+int jornada_ssp_byte(u8 byte)
+{
+	int timeout = 400000;
+	u16 ret;
+
+	while ((GPLR & GPIO_GPIO10)) {
+		if (!--timeout) {
+			printk(KERN_WARNING "SSP: timeout while waiting for transmit\n");
+			return -ETIMEDOUT;
+		}
+		cpu_relax();
+	}
+
+	ret = jornada_ssp_reverse(byte) << 8;
+
+	ssp_write_word(ret);
+	ssp_read_word(&ret);
+
+	return jornada_ssp_reverse(ret);
+};
+EXPORT_SYMBOL(jornada_ssp_byte);
+
+/**
+ * jornada_ssp_inout - decide if input is command or trading byte
+ *
+ * returns : (jornada_ssp_byte(byte)) on success
+ *         : %-ETIMEOUT on timeout failure
+ */
+int jornada_ssp_inout(u8 byte)
+{
+	int ret, i;
+
+	/* true means command byte */
+	if (byte != TXDUMMY) {
+		ret = jornada_ssp_byte(byte);
+		/* Proper return to commands is TxDummy */
+		if (ret != TXDUMMY) {
+			for (i = 0; i < 256; i++)/* flushing bus */
+				if (jornada_ssp_byte(TXDUMMY) == -1)
+					break;
+			return -ETIMEDOUT;
+		}
+	} else /* Exchange TxDummy for data */
+		ret = jornada_ssp_byte(TXDUMMY);
+
+	return ret;
+};
+EXPORT_SYMBOL(jornada_ssp_inout);
+
+/**
+ * jornada_ssp_start - enable mcu
+ *
+ */
+int jornada_ssp_start()
+{
+	spin_lock_irqsave(&jornada_ssp_lock, jornada_ssp_flags);
+	GPCR = GPIO_GPIO25;
+	udelay(50);
+	return 0;
+};
+EXPORT_SYMBOL(jornada_ssp_start);
+
+/**
+ * jornada_ssp_end - disable mcu and turn off lock
+ *
+ */
+int jornada_ssp_end()
+{
+	GPSR = GPIO_GPIO25;
+	spin_unlock_irqrestore(&jornada_ssp_lock, jornada_ssp_flags);
+	return 0;
+};
+EXPORT_SYMBOL(jornada_ssp_end);
+
+static int __init jornada_ssp_probe(struct platform_device *dev)
+{
+	int ret;
+
+	GPSR = GPIO_GPIO25;
+
+	ret = ssp_init();
+
+	/* worked fine, lets not bother with anything else */
+	if (!ret) {
+		printk(KERN_INFO "SSP: device initialized with irq\n");
+		return ret;
+	}
+
+	printk(KERN_WARNING "SSP: initialization failed, trying non-irq solution \n");
+
+	/* init of Serial 4 port */
+	Ser4MCCR0 = 0;
+	Ser4SSCR0 = 0x0387;
+	Ser4SSCR1 = 0x18;
+
+	/* clear out any left over data */
+	ssp_flush();
+
+	/* enable MCU */
+	jornada_ssp_start();
+
+	/* see if return value makes sense */
+	ret = jornada_ssp_inout(GETBRIGHTNESS);
+
+	/* seems like it worked, just feed it with TxDummy to get rid of data */
+	if (ret == TxDummy)
+		jornada_ssp_inout(TXDUMMY);
+
+	jornada_ssp_end();
+
+	/* failed, lets just kill everything */
+	if (ret == -ETIMEDOUT) {
+		printk(KERN_WARNING "SSP: attempts failed, bailing\n");
+		ssp_exit();
+		return -ENODEV;
+	}
+
+	/* all fine */
+	printk(KERN_INFO "SSP: device initialized\n");
+	return 0;
+};
+
+static int jornada_ssp_remove(struct platform_device *dev)
+{
+	/* Note that this doesnt actually remove the driver, since theres nothing to remove
+	 * It just makes sure everything is turned off */
+	GPSR = GPIO_GPIO25;
+	ssp_exit();
+	return 0;
+};
+
+struct platform_driver jornadassp_driver = {
+	.probe	= jornada_ssp_probe,
+	.remove	= jornada_ssp_remove,
+	.driver	= {
+		.name	= "jornada_ssp",
+	},
+};
+
+static int __init jornada_ssp_init(void)
+{
+	return platform_driver_register(&jornadassp_driver);
+}
diff --git a/arch/arm/mach-sa1100/neponset.c b/arch/arm/mach-sa1100/neponset.c
index 3a0a1ee..9f1ed15 100644
--- a/arch/arm/mach-sa1100/neponset.c
+++ b/arch/arm/mach-sa1100/neponset.c
@@ -292,6 +292,8 @@
 	&smc91x_device,
 };
 
+extern void sa1110_mb_disable(void);
+
 static int __init neponset_init(void)
 {
 	platform_driver_register(&neponset_device_driver);
diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig
index e7904bc9..12161ae 100644
--- a/arch/arm/mm/Kconfig
+++ b/arch/arm/mm/Kconfig
@@ -345,13 +345,14 @@
 # ARMv6
 config CPU_V6
 	bool "Support ARM V6 processor"
-	depends on ARCH_INTEGRATOR || MACH_REALVIEW_EB || ARCH_OMAP2
+	depends on ARCH_INTEGRATOR || MACH_REALVIEW_EB || ARCH_OMAP2 || ARCH_MX3
+	default y if ARCH_MX3
 	select CPU_32v6
 	select CPU_ABRT_EV6
 	select CPU_CACHE_V6
 	select CPU_CACHE_VIPT
 	select CPU_CP15_MMU
-	select CPU_HAS_ASID
+	select CPU_HAS_ASID if MMU
 	select CPU_COPY_V6 if MMU
 	select CPU_TLB_V6 if MMU
 
@@ -359,7 +360,7 @@
 config CPU_32v6K
 	bool "Support ARM V6K processor extensions" if !SMP
 	depends on CPU_V6
-	default y if SMP
+	default y if SMP && !ARCH_MX3
 	help
 	  Say Y here if your ARMv6 processor supports the 'K' extension.
 	  This enables the kernel to use some instructions not present
@@ -377,7 +378,7 @@
 	select CPU_CACHE_V7
 	select CPU_CACHE_VIPT
 	select CPU_CP15_MMU
-	select CPU_HAS_ASID
+	select CPU_HAS_ASID if MMU
 	select CPU_COPY_V6 if MMU
 	select CPU_TLB_V7 if MMU
 
@@ -405,6 +406,7 @@
 
 config CPU_32v6
 	bool
+	select TLS_REG_EMUL if !CPU_32v6K && !MMU
 
 config CPU_32v7
 	bool
@@ -598,7 +600,7 @@
 
 config CPU_DCACHE_WRITETHROUGH
 	bool "Force write through D-cache"
-	depends on (CPU_ARM740T || CPU_ARM920T || CPU_ARM922T || CPU_ARM925T || CPU_ARM926T || CPU_ARM940T || CPU_ARM946E || CPU_ARM1020 || CPU_V6) && !CPU_DCACHE_DISABLE
+	depends on (CPU_ARM740T || CPU_ARM920T || CPU_ARM922T || CPU_ARM925T || CPU_ARM926T || CPU_ARM940T || CPU_ARM946E || CPU_ARM1020) && !CPU_DCACHE_DISABLE
 	default y if CPU_ARM925T
 	help
 	  Say Y here to use the data cache in writethrough mode. Unless you
@@ -611,12 +613,6 @@
 	  Say Y here to use the predictable round-robin cache replacement
 	  policy.  Unless you specifically require this or are unsure, say N.
 
-config CPU_L2CACHE_DISABLE
-	bool "Disable level 2 cache"
-	depends on CPU_V7
-	help
-	  Say Y here to disable the level 2 cache.  If unsure, say N.
-
 config CPU_BPREDICT_DISABLE
 	bool "Disable branch prediction"
 	depends on CPU_ARM1020 || CPU_V6 || CPU_XSC3 || CPU_V7
diff --git a/arch/arm/mm/cache-l2x0.c b/arch/arm/mm/cache-l2x0.c
index 08a36f1..b4e9b73 100644
--- a/arch/arm/mm/cache-l2x0.c
+++ b/arch/arm/mm/cache-l2x0.c
@@ -17,6 +17,7 @@
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
  */
 #include <linux/init.h>
+#include <linux/spinlock.h>
 
 #include <asm/cacheflush.h>
 #include <asm/io.h>
@@ -25,14 +26,19 @@
 #define CACHE_LINE_SIZE		32
 
 static void __iomem *l2x0_base;
+static DEFINE_SPINLOCK(l2x0_lock);
 
 static inline void sync_writel(unsigned long val, unsigned long reg,
 			       unsigned long complete_mask)
 {
+	unsigned long flags;
+
+	spin_lock_irqsave(&l2x0_lock, flags);
 	writel(val, l2x0_base + reg);
 	/* wait for the operation to complete */
 	while (readl(l2x0_base + reg) & complete_mask)
 		;
+	spin_unlock_irqrestore(&l2x0_lock, flags);
 }
 
 static inline void cache_sync(void)
diff --git a/arch/arm/mm/mmu.c b/arch/arm/mm/mmu.c
index 3b5e47d..e5d61ee 100644
--- a/arch/arm/mm/mmu.c
+++ b/arch/arm/mm/mmu.c
@@ -114,6 +114,10 @@
 	}
 	if (i == ARRAY_SIZE(cache_policies))
 		printk(KERN_ERR "ERROR: unknown or unsupported cache policy\n");
+	if (cpu_architecture() >= CPU_ARCH_ARMv6) {
+		printk(KERN_WARNING "Only cachepolicy=writeback supported on ARMv6 and later\n");
+		cachepolicy = CPOLICY_WRITEBACK;
+	}
 	flush_cache_all();
 	set_cr(cr_alignment);
 }
@@ -252,13 +256,15 @@
 	int cpu_arch = cpu_architecture();
 	int i;
 
+	if (cpu_arch < CPU_ARCH_ARMv6) {
 #if defined(CONFIG_CPU_DCACHE_DISABLE)
-	if (cachepolicy > CPOLICY_BUFFERED)
-		cachepolicy = CPOLICY_BUFFERED;
+		if (cachepolicy > CPOLICY_BUFFERED)
+			cachepolicy = CPOLICY_BUFFERED;
 #elif defined(CONFIG_CPU_DCACHE_WRITETHROUGH)
-	if (cachepolicy > CPOLICY_WRITETHROUGH)
-		cachepolicy = CPOLICY_WRITETHROUGH;
+		if (cachepolicy > CPOLICY_WRITETHROUGH)
+			cachepolicy = CPOLICY_WRITETHROUGH;
 #endif
+	}
 	if (cpu_arch < CPU_ARCH_ARMv5) {
 		if (cachepolicy >= CPOLICY_WRITEALLOC)
 			cachepolicy = CPOLICY_WRITEBACK;
diff --git a/arch/arm/mm/proc-syms.c b/arch/arm/mm/proc-syms.c
index 9f396b4..2b5ba39 100644
--- a/arch/arm/mm/proc-syms.c
+++ b/arch/arm/mm/proc-syms.c
@@ -31,12 +31,14 @@
 EXPORT_SYMBOL(cpu_cache);
 #endif
 
+#ifdef CONFIG_MMU
 #ifndef MULTI_USER
 EXPORT_SYMBOL(__cpu_clear_user_page);
 EXPORT_SYMBOL(__cpu_copy_user_page);
 #else
 EXPORT_SYMBOL(cpu_user);
 #endif
+#endif
 
 /*
  * No module should need to touch the TLB (and currently
diff --git a/arch/arm/mm/proc-v7.S b/arch/arm/mm/proc-v7.S
index 718f478..e0acc5a 100644
--- a/arch/arm/mm/proc-v7.S
+++ b/arch/arm/mm/proc-v7.S
@@ -77,6 +77,7 @@
  *	- we are not using split page tables
  */
 ENTRY(cpu_v7_switch_mm)
+#ifdef CONFIG_MMU
 	mov	r2, #0
 	ldr	r1, [r1, #MM_CONTEXT_ID]	@ get mm->context.id
 	orr	r0, r0, #TTB_RGN_OC_WB		@ mark PTWs outer cacheable, WB
@@ -86,6 +87,7 @@
 	isb
 	mcr	p15, 0, r1, c13, c0, 1		@ set context ID
 	isb
+#endif
 	mov	pc, lr
 
 /*
@@ -109,6 +111,7 @@
  *	  1111   0   1   1	r/w	r/w
  */
 ENTRY(cpu_v7_set_pte_ext)
+#ifdef CONFIG_MMU
 	str	r1, [r0], #-2048		@ linux version
 
 	bic	r3, r1, #0x000003f0
@@ -136,6 +139,7 @@
 
 	str	r3, [r0]
 	mcr	p15, 0, r0, c7, c10, 1		@ flush_pte
+#endif
 	mov	pc, lr
 
 cpu_v7_name:
@@ -169,6 +173,7 @@
 	mcr	p15, 0, r10, c7, c5, 0		@ I+BTB cache invalidate
 #endif
 	dsb
+#ifdef CONFIG_MMU
 	mcr	p15, 0, r10, c8, c7, 0		@ invalidate I + D TLBs
 	mcr	p15, 0, r10, c2, c0, 2		@ TTB control register
 	orr	r4, r4, #TTB_RGN_OC_WB		@ mark PTWs outer cacheable, WB
@@ -176,21 +181,12 @@
 	mcr	p15, 0, r4, c2, c0, 1		@ load TTB1
 	mov	r10, #0x1f			@ domains 0, 1 = manager
 	mcr	p15, 0, r10, c3, c0, 0		@ load domain access register
-#ifndef CONFIG_CPU_L2CACHE_DISABLE
-	@ L2 cache configuration in the L2 aux control register
-	mrc	p15, 1, r10, c9, c0, 2
-	bic	r10, r10, #(1 << 16)		@ L2 outer cache
-	mcr	p15, 1, r10, c9, c0, 2
-	@ L2 cache is enabled in the aux control register
-	mrc	p15, 0, r10, c1, c0, 1
-	orr	r10, r10, #2
-	mcr	p15, 0, r10, c1, c0, 1
 #endif
-	mrc	p15, 0, r0, c1, c0, 0		@ read control register
-	ldr	r10, cr1_clear			@ get mask for bits to clear
-	bic	r0, r0, r10			@ clear bits them
-	ldr	r10, cr1_set			@ get mask for bits to set
-	orr	r0, r0, r10			@ set them
+	adr	r5, v7_crval
+	ldmia	r5, {r5, r6}
+   	mrc	p15, 0, r0, c1, c0, 0		@ read control register
+	bic	r0, r0, r5			@ clear bits them
+	orr	r0, r0, r6			@ set them
 	mov	pc, lr				@ return to head.S:__ret
 
 	/*
@@ -199,12 +195,9 @@
 	 * rrrr rrrx xxx0 0101 xxxx xxxx x111 xxxx < forced
 	 *         0 110       0011 1.00 .111 1101 < we want
 	 */
-	.type	cr1_clear, #object
-	.type	cr1_set, #object
-cr1_clear:
-	.word	0x0120c302
-cr1_set:
-	.word	0x00c0387d
+	.type	v7_crval, #object
+v7_crval:
+	crval	clear=0x0120c302, mmuset=0x00c0387d, ucset=0x00c0187c
 
 __v7_setup_stack:
 	.space	4 * 11				@ 11 registers
diff --git a/arch/arm/plat-mxc/Kconfig b/arch/arm/plat-mxc/Kconfig
new file mode 100644
index 0000000..03a65c0
--- /dev/null
+++ b/arch/arm/plat-mxc/Kconfig
@@ -0,0 +1,20 @@
+if ARCH_MXC
+
+menu "Freescale MXC Implementations"
+
+choice
+	prompt "MXC/iMX System Type"
+	default 0
+
+config ARCH_MX3
+	bool "MX3-based"
+	help
+	  This enables support for systems based on the Freescale i.MX3 family
+
+endchoice
+
+source "arch/arm/mach-mx3/Kconfig"
+
+endmenu
+
+endif
diff --git a/arch/arm/plat-mxc/Makefile b/arch/arm/plat-mxc/Makefile
new file mode 100644
index 0000000..66ad9c2
--- /dev/null
+++ b/arch/arm/plat-mxc/Makefile
@@ -0,0 +1,10 @@
+#
+# Makefile for the linux kernel.
+#
+
+# Common support
+obj-y := irq.o
+
+obj-m :=
+obj-n :=
+obj-  :=
diff --git a/arch/arm/plat-mxc/irq.c b/arch/arm/plat-mxc/irq.c
new file mode 100644
index 0000000..87d253b
--- /dev/null
+++ b/arch/arm/plat-mxc/irq.c
@@ -0,0 +1,83 @@
+/*
+ *  Copyright 2004-2007 Freescale Semiconductor, Inc. All Rights Reserved.
+ */
+
+/*
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/errno.h>
+#include <asm/hardware.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/mach/irq.h>
+#include <asm/arch/common.h>
+
+/*!
+ * Disable interrupt number "irq" in the AVIC
+ *
+ * @param  irq          interrupt source number
+ */
+static void mxc_mask_irq(unsigned int irq)
+{
+	__raw_writel(irq, AVIC_INTDISNUM);
+}
+
+/*!
+ * Enable interrupt number "irq" in the AVIC
+ *
+ * @param  irq          interrupt source number
+ */
+static void mxc_unmask_irq(unsigned int irq)
+{
+	__raw_writel(irq, AVIC_INTENNUM);
+}
+
+static struct irq_chip mxc_avic_chip = {
+	.mask_ack = mxc_mask_irq,
+	.mask = mxc_mask_irq,
+	.unmask = mxc_unmask_irq,
+};
+
+/*!
+ * This function initializes the AVIC hardware and disables all the
+ * interrupts. It registers the interrupt enable and disable functions
+ * to the kernel for each interrupt source.
+ */
+void __init mxc_init_irq(void)
+{
+	int i;
+	u32 reg;
+
+	/* put the AVIC into the reset value with
+	 * all interrupts disabled
+	 */
+	__raw_writel(0, AVIC_INTCNTL);
+	__raw_writel(0x1f, AVIC_NIMASK);
+
+	/* disable all interrupts */
+	__raw_writel(0, AVIC_INTENABLEH);
+	__raw_writel(0, AVIC_INTENABLEL);
+
+	/* all IRQ no FIQ */
+	__raw_writel(0, AVIC_INTTYPEH);
+	__raw_writel(0, AVIC_INTTYPEL);
+	for (i = 0; i < MXC_MAX_INT_LINES; i++) {
+		set_irq_chip(i, &mxc_avic_chip);
+		set_irq_handler(i, handle_level_irq);
+		set_irq_flags(i, IRQF_VALID);
+	}
+
+	/* Set WDOG2's interrupt the highest priority level (bit 28-31) */
+	reg = __raw_readl(AVIC_NIPRIORITY6);
+	reg |= (0xF << 28);
+	__raw_writel(reg, AVIC_NIPRIORITY6);
+
+	printk(KERN_INFO "MXC IRQ initialized\n");
+}
diff --git a/arch/arm/plat-s3c/Kconfig b/arch/arm/plat-s3c/Kconfig
new file mode 100644
index 0000000..31656c3
--- /dev/null
+++ b/arch/arm/plat-s3c/Kconfig
@@ -0,0 +1,104 @@
+# arch/arm/plat-s3c/Kconfig
+#
+# Copyright 2007 Simtec Electronics
+#
+# Licensed under GPLv2
+
+config PLAT_S3C
+	bool
+	depends on ARCH_S3C2410
+	default y if ARCH_S3C2410
+	select NO_IOPORT
+	help
+	  Base platform code for any Samsung S3C device
+
+# low-level serial option nodes
+
+config CPU_LLSERIAL_S3C2410_ONLY
+	bool
+	depends on ARCH_S3C2410
+	default y if CPU_LLSERIAL_S3C2410 && !CPU_LLSERIAL_S3C2440
+
+config CPU_LLSERIAL_S3C2440_ONLY
+	bool
+	depends on ARCH_S3C2410
+	default y if CPU_LLSERIAL_S3C2440 && !CPU_LLSERIAL_S3C2410
+
+config CPU_LLSERIAL_S3C2410
+	bool
+	depends on ARCH_S3C2410
+	help
+	  Selected if there is an S3C2410 (or register compatible) serial
+	  low-level implementation needed
+
+config CPU_LLSERIAL_S3C2440
+	bool
+	depends on ARCH_S3C2410
+	help
+	  Selected if there is an S3C2440 (or register compatible) serial
+	  low-level implementation needed
+
+# boot configurations
+
+comment "Boot options"
+
+config S3C_BOOT_WATCHDOG
+	bool "S3C Initialisation watchdog"
+	depends on PLAT_S3C && S3C2410_WATCHDOG
+	help
+	  Say y to enable the watchdog during the kernel decompression
+	  stage. If the kernel fails to uncompress, then the watchdog
+	  will trigger a reset and the system should restart.
+
+config S3C_BOOT_ERROR_RESET
+	bool "S3C Reboot on decompression error"
+	depends on PLAT_S3C
+	help
+	  Say y here to use the watchdog to reset the system if the
+	  kernel decompressor detects an error during decompression.
+
+comment "Power management"
+
+config S3C2410_PM_DEBUG
+	bool "S3C2410 PM Suspend debug"
+	depends on PLAT_S3C && PM
+	help
+	  Say Y here if you want verbose debugging from the PM Suspend and
+	  Resume code. See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt>
+	  for more information.
+
+config S3C2410_PM_CHECK
+	bool "S3C2410 PM Suspend Memory CRC"
+	depends on PLAT_S3C && PM && CRC32
+	help
+ 	  Enable the PM code's memory area checksum over sleep. This option
+	  will generate CRCs of all blocks of memory, and store them before
+	  going to sleep. The blocks are then checked on resume for any
+	  errors.
+
+	  Note, this can take several seconds depending on memory size
+	  and CPU speed.
+
+	  See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt>
+
+config S3C2410_PM_CHECK_CHUNKSIZE
+	int "S3C2410 PM Suspend CRC Chunksize (KiB)"
+	depends on PLAT_S3C && PM && S3C2410_PM_CHECK
+	default 64
+	help
+	  Set the chunksize in Kilobytes of the CRC for checking memory
+	  corruption over suspend and resume. A smaller value will mean that
+	  the CRC data block will take more memory, but wil identify any
+	  faults with better precision.
+
+	  See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt>
+
+config S3C_LOWLEVEL_UART_PORT
+	int "S3C UART to use for low-level messages"
+	depends on PLAT_S3C
+	default 0
+	help
+	  Choice of which UART port to use for the low-level messages,
+	  such as the `Uncompressing...` at start time. The value of
+	  this configuration should be between zero and two. The port
+	  must have been initialised by the boot-loader before use.
diff --git a/arch/arm/plat-s3c24xx/Kconfig b/arch/arm/plat-s3c24xx/Kconfig
index b972f36..b66fb3c 100644
--- a/arch/arm/plat-s3c24xx/Kconfig
+++ b/arch/arm/plat-s3c24xx/Kconfig
@@ -10,7 +10,7 @@
 	default y if ARCH_S3C2410
 	select NO_IOPORT
 	help
-	  Base platform code for any Samsung S3C device
+	  Base platform code for any Samsung S3C24XX device
 
 if PLAT_S3C24XX
 
@@ -26,64 +26,6 @@
 	  Common power management code for systems that are
 	  compatible with the Simtec style of power management
 
-config S3C2410_BOOT_WATCHDOG
-	bool "S3C2410 Initialisation watchdog"
-	depends on ARCH_S3C2410 && S3C2410_WATCHDOG
-	help
-	  Say y to enable the watchdog during the kernel decompression
-	  stage. If the kernel fails to uncompress, then the watchdog
-	  will trigger a reset and the system should restart.
-
-config S3C2410_BOOT_ERROR_RESET
-	bool "S3C2410 Reboot on decompression error"
-	depends on ARCH_S3C2410
-	help
-	  Say y here to use the watchdog to reset the system if the
-	  kernel decompressor detects an error during decompression.
-
-config S3C2410_PM_DEBUG
-	bool "S3C2410 PM Suspend debug"
-	depends on ARCH_S3C2410 && PM
-	help
-	  Say Y here if you want verbose debugging from the PM Suspend and
-	  Resume code. See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt>
-	  for more information.
-
-config S3C2410_PM_CHECK
-	bool "S3C2410 PM Suspend Memory CRC"
-	depends on ARCH_S3C2410 && PM && CRC32
-	help
- 	  Enable the PM code's memory area checksum over sleep. This option
-	  will generate CRCs of all blocks of memory, and store them before
-	  going to sleep. The blocks are then checked on resume for any
-	  errors.
-
-	  Note, this can take several seconds depending on memory size
-	  and CPU speed.
-
-	  See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt>
-
-config S3C2410_PM_CHECK_CHUNKSIZE
-	int "S3C2410 PM Suspend CRC Chunksize (KiB)"
-	depends on ARCH_S3C2410 && PM && S3C2410_PM_CHECK
-	default 64
-	help
-	  Set the chunksize in Kilobytes of the CRC for checking memory
-	  corruption over suspend and resume. A smaller value will mean that
-	  the CRC data block will take more memory, but wil identify any
-	  faults with better precision.
-
-	  See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt>
-
-config S3C2410_LOWLEVEL_UART_PORT
-	int "S3C2410 UART to use for low-level messages"
-	default 0
-	help
-	  Choice of which UART port to use for the low-level messages,
-	  such as the `Uncompressing...` at start time. The value of
-	  this configuration should be between zero and two. The port
-	  must have been initialised by the boot-loader before use.
-
 config S3C2410_DMA
 	bool "S3C2410 DMA support"
 	depends on ARCH_S3C2410
diff --git a/arch/arm/plat-s3c24xx/common-smdk.c b/arch/arm/plat-s3c24xx/common-smdk.c
index 7ed19b2..398c7ac 100644
--- a/arch/arm/plat-s3c24xx/common-smdk.c
+++ b/arch/arm/plat-s3c24xx/common-smdk.c
@@ -38,7 +38,7 @@
 #include <asm/arch/regs-gpio.h>
 #include <asm/arch/leds-gpio.h>
 
-#include <asm/arch/nand.h>
+#include <asm/plat-s3c/nand.h>
 
 #include <asm/plat-s3c24xx/common-smdk.h>
 #include <asm/plat-s3c24xx/devs.h>
diff --git a/arch/arm/plat-s3c24xx/cpu.c b/arch/arm/plat-s3c24xx/cpu.c
index 8ce4904..f513ab0 100644
--- a/arch/arm/plat-s3c24xx/cpu.c
+++ b/arch/arm/plat-s3c24xx/cpu.c
@@ -38,7 +38,7 @@
 #include <asm/mach/map.h>
 
 #include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-serial.h>
+#include <asm/plat-s3c/regs-serial.h>
 
 #include <asm/plat-s3c24xx/cpu.h>
 #include <asm/plat-s3c24xx/devs.h>
diff --git a/arch/arm/plat-s3c24xx/devs.c b/arch/arm/plat-s3c24xx/devs.c
index 5875da0..e546e93 100644
--- a/arch/arm/plat-s3c24xx/devs.c
+++ b/arch/arm/plat-s3c24xx/devs.c
@@ -28,12 +28,12 @@
 #include <asm/io.h>
 #include <asm/irq.h>
 
-#include <asm/arch/regs-serial.h>
-#include <asm/arch/udc.h>
+#include <asm/plat-s3c/regs-serial.h>
+#include <asm/plat-s3c24xx/udc.h>
 
 #include <asm/plat-s3c24xx/devs.h>
 #include <asm/plat-s3c24xx/cpu.h>
-#include <asm/arch/regs-spi.h>
+#include <asm/plat-s3c24xx/regs-spi.h>
 
 /* Serial port registrations */
 
diff --git a/arch/arm/plat-s3c24xx/pm.c b/arch/arm/plat-s3c24xx/pm.c
index 5692ecc..eab1850 100644
--- a/arch/arm/plat-s3c24xx/pm.c
+++ b/arch/arm/plat-s3c24xx/pm.c
@@ -40,7 +40,7 @@
 #include <asm/hardware.h>
 #include <asm/io.h>
 
-#include <asm/arch/regs-serial.h>
+#include <asm/plat-s3c/regs-serial.h>
 #include <asm/arch/regs-clock.h>
 #include <asm/arch/regs-gpio.h>
 #include <asm/arch/regs-mem.h>
diff --git a/arch/arm/plat-s3c24xx/s3c244x.c b/arch/arm/plat-s3c24xx/s3c244x.c
index 767f2e9..3444b13 100644
--- a/arch/arm/plat-s3c24xx/s3c244x.c
+++ b/arch/arm/plat-s3c24xx/s3c244x.c
@@ -30,7 +30,7 @@
 #include <asm/irq.h>
 
 #include <asm/arch/regs-clock.h>
-#include <asm/arch/regs-serial.h>
+#include <asm/plat-s3c/regs-serial.h>
 #include <asm/arch/regs-gpio.h>
 #include <asm/arch/regs-gpioj.h>
 #include <asm/arch/regs-dsc.h>
@@ -47,7 +47,6 @@
 	IODESC_ENT(CLKPWR),
 	IODESC_ENT(TIMER),
 	IODESC_ENT(WATCHDOG),
-	IODESC_ENT(LCD),
 };
 
 /* uart initialisation */
diff --git a/arch/arm/plat-s3c24xx/sleep.S b/arch/arm/plat-s3c24xx/sleep.S
index 7b7ae79..d47113b 100644
--- a/arch/arm/plat-s3c24xx/sleep.S
+++ b/arch/arm/plat-s3c24xx/sleep.S
@@ -32,7 +32,7 @@
 #include <asm/arch/regs-gpio.h>
 #include <asm/arch/regs-clock.h>
 #include <asm/arch/regs-mem.h>
-#include <asm/arch/regs-serial.h>
+#include <asm/plat-s3c/regs-serial.h>
 
 /* CONFIG_DEBUG_RESUME is dangerous if your bootloader does not
  * reset the UART configuration, only enable if you really need this!
diff --git a/arch/arm/plat-s3c24xx/time.c b/arch/arm/plat-s3c24xx/time.c
index b766737..2ec1daa 100644
--- a/arch/arm/plat-s3c24xx/time.c
+++ b/arch/arm/plat-s3c24xx/time.c
@@ -33,7 +33,7 @@
 #include <asm/io.h>
 #include <asm/irq.h>
 #include <asm/arch/map.h>
-#include <asm/arch/regs-timer.h>
+#include <asm/plat-s3c/regs-timer.h>
 #include <asm/arch/regs-irq.h>
 #include <asm/mach/time.h>
 
diff --git a/arch/arm/vfp/vfphw.S b/arch/arm/vfp/vfphw.S
index d4b7b22..0ac022f 100644
--- a/arch/arm/vfp/vfphw.S
+++ b/arch/arm/vfp/vfphw.S
@@ -74,14 +74,14 @@
 
 	VFPFMRX	r1, FPEXC		@ Is the VFP enabled?
 	DBGSTR1	"fpexc %08x", r1
-	tst	r1, #FPEXC_ENABLE
+	tst	r1, #FPEXC_EN
 	bne	look_for_VFP_exceptions	@ VFP is already enabled
 
 	DBGSTR1 "enable %x", r10
 	ldr	r3, last_VFP_context_address
-	orr	r1, r1, #FPEXC_ENABLE	@ user FPEXC has the enable bit set
+	orr	r1, r1, #FPEXC_EN	@ user FPEXC has the enable bit set
 	ldr	r4, [r3, r11, lsl #2]	@ last_VFP_context pointer
-	bic	r5, r1, #FPEXC_EXCEPTION @ make sure exceptions are disabled
+	bic	r5, r1, #FPEXC_EX	@ make sure exceptions are disabled
 	cmp	r4, r10
 	beq	check_for_exception	@ we are returning to the same
 					@ process, so the registers are
@@ -124,7 +124,7 @@
 	VFPFMXR	FPSCR, r5		@ restore status
 
 check_for_exception:
-	tst	r1, #FPEXC_EXCEPTION
+	tst	r1, #FPEXC_EX
 	bne	process_exception	@ might as well handle the pending
 					@ exception before retrying branch
 					@ out before setting an FPEXC that
@@ -136,10 +136,10 @@
 
 
 look_for_VFP_exceptions:
-	tst	r1, #FPEXC_EXCEPTION
+	tst	r1, #FPEXC_EX
 	bne	process_exception
 	VFPFMRX	r5, FPSCR
-	tst	r5, #FPSCR_IXE		@ IXE doesn't set FPEXC_EXCEPTION !
+	tst	r5, #FPSCR_IXE		@ IXE doesn't set FPEXC_EX !
 	bne	process_exception
 
 	@ Fall into hand on to next handler - appropriate coproc instr
diff --git a/arch/arm/vfp/vfpmodule.c b/arch/arm/vfp/vfpmodule.c
index 1106b5f..04ddab2 100644
--- a/arch/arm/vfp/vfpmodule.c
+++ b/arch/arm/vfp/vfpmodule.c
@@ -53,7 +53,7 @@
 		 * case the thread migrates to a different CPU. The
 		 * restoring is done lazily.
 		 */
-		if ((fpexc & FPEXC_ENABLE) && last_VFP_context[cpu]) {
+		if ((fpexc & FPEXC_EN) && last_VFP_context[cpu]) {
 			vfp_save_state(last_VFP_context[cpu], fpexc);
 			last_VFP_context[cpu]->hard.cpu = cpu;
 		}
@@ -70,7 +70,7 @@
 		 * Always disable VFP so we can lazily save/restore the
 		 * old state.
 		 */
-		fmxr(FPEXC, fpexc & ~FPEXC_ENABLE);
+		fmxr(FPEXC, fpexc & ~FPEXC_EN);
 		return NOTIFY_DONE;
 	}
 
@@ -81,13 +81,13 @@
 		 */
 		memset(vfp, 0, sizeof(union vfp_state));
 
-		vfp->hard.fpexc = FPEXC_ENABLE;
+		vfp->hard.fpexc = FPEXC_EN;
 		vfp->hard.fpscr = FPSCR_ROUND_NEAREST;
 
 		/*
 		 * Disable VFP to ensure we initialise it first.
 		 */
-		fmxr(FPEXC, fmrx(FPEXC) & ~FPEXC_ENABLE);
+		fmxr(FPEXC, fmrx(FPEXC) & ~FPEXC_EN);
 	}
 
 	/* flush and release case: Per-thread VFP cleanup. */
@@ -229,7 +229,7 @@
 	/*
 	 * Enable access to the VFP so we can handle the bounce.
 	 */
-	fmxr(FPEXC, fpexc & ~(FPEXC_EXCEPTION|FPEXC_INV|FPEXC_UFC|FPEXC_IOC));
+	fmxr(FPEXC, fpexc & ~(FPEXC_EX|FPEXC_INV|FPEXC_UFC|FPEXC_IOC));
 
 	orig_fpscr = fpscr = fmrx(FPSCR);
 
@@ -248,7 +248,7 @@
 	/*
 	 * Modify fpscr to indicate the number of iterations remaining
 	 */
-	if (fpexc & FPEXC_EXCEPTION) {
+	if (fpexc & FPEXC_EX) {
 		u32 len;
 
 		len = fpexc + (1 << FPEXC_LENGTH_BIT);
diff --git a/drivers/net/arm/ether1.c b/drivers/net/arm/ether1.c
index f21148e..80f33b6 100644
--- a/drivers/net/arm/ether1.c
+++ b/drivers/net/arm/ether1.c
@@ -36,7 +36,6 @@
 #include <linux/types.h>
 #include <linux/fcntl.h>
 #include <linux/interrupt.h>
-#include <linux/ptrace.h>
 #include <linux/ioport.h>
 #include <linux/in.h>
 #include <linux/slab.h>
@@ -75,7 +74,7 @@
 
 /* ------------------------------------------------------------------------- */
 
-static char version[] __initdata = "ether1 ethernet driver (c) 2000 Russell King v1.07\n";
+static char version[] __devinitdata = "ether1 ethernet driver (c) 2000 Russell King v1.07\n";
 
 #define BUS_16 16
 #define BUS_8  8
diff --git a/drivers/net/arm/ether3.c b/drivers/net/arm/ether3.c
index a7cac69..3805506 100644
--- a/drivers/net/arm/ether3.c
+++ b/drivers/net/arm/ether3.c
@@ -51,7 +51,6 @@
 #include <linux/types.h>
 #include <linux/fcntl.h>
 #include <linux/interrupt.h>
-#include <linux/ptrace.h>
 #include <linux/ioport.h>
 #include <linux/in.h>
 #include <linux/slab.h>
@@ -69,7 +68,7 @@
 #include <asm/ecard.h>
 #include <asm/io.h>
 
-static char version[] __initdata = "ether3 ethernet driver (c) 1995-2000 R.M.King v1.17\n";
+static char version[] __devinitdata = "ether3 ethernet driver (c) 1995-2000 R.M.King v1.17\n";
 
 #include "ether3.h"
 
diff --git a/drivers/net/arm/etherh.c b/drivers/net/arm/etherh.c
index 769ba69..0d37d9d 100644
--- a/drivers/net/arm/etherh.c
+++ b/drivers/net/arm/etherh.c
@@ -31,7 +31,6 @@
 #include <linux/types.h>
 #include <linux/fcntl.h>
 #include <linux/interrupt.h>
-#include <linux/ptrace.h>
 #include <linux/ioport.h>
 #include <linux/in.h>
 #include <linux/slab.h>
diff --git a/drivers/scsi/arm/cumana_1.c b/drivers/scsi/arm/cumana_1.c
index cf9a21c..49d838e 100644
--- a/drivers/scsi/arm/cumana_1.c
+++ b/drivers/scsi/arm/cumana_1.c
@@ -24,7 +24,7 @@
 
 #define CUMANASCSI_PUBLIC_RELEASE 1
 
-#define NCR5380_implementation_fields	int port, ctrl
+#define priv(host)			((struct NCR5380_hostdata *)(host)->hostdata)
 #define NCR5380_local_declare()		struct Scsi_Host *_instance
 #define NCR5380_setup(instance)		_instance = instance
 #define NCR5380_read(reg)		cumanascsi_read(_instance, reg)
@@ -33,6 +33,11 @@
 #define NCR5380_queue_command		cumanascsi_queue_command
 #define NCR5380_proc_info		cumanascsi_proc_info
 
+#define NCR5380_implementation_fields	\
+	unsigned ctrl;			\
+	void __iomem *base;		\
+	void __iomem *dma
+
 #define BOARD_NORMAL	0
 #define BOARD_NCR53C400	1
 
@@ -47,193 +52,163 @@
 	return "";
 }
 
-#ifdef NOT_EFFICIENT
-#define CTRL(p,v)     outb(*ctrl = (v), (p) - 577)
-#define STAT(p)       inb((p)+1)
-#define IN(p)         inb((p))
-#define OUT(v,p)      outb((v), (p))
-#else
-#define CTRL(p,v)	(p[-2308] = (*ctrl = (v)))
-#define STAT(p)		(p[4])
-#define IN(p)		(*(p))
-#define IN2(p)		((unsigned short)(*(volatile unsigned long *)(p)))
-#define OUT(v,p)	(*(p) = (v))
-#define OUT2(v,p)	(*((volatile unsigned long *)(p)) = (v))
-#endif
-#define L(v)		(((v)<<16)|((v) & 0x0000ffff))
-#define H(v)		(((v)>>16)|((v) & 0xffff0000))
+#define CTRL	0x16fc
+#define STAT	0x2004
+#define L(v)	(((v)<<16)|((v) & 0x0000ffff))
+#define H(v)	(((v)>>16)|((v) & 0xffff0000))
 
 static inline int
-NCR5380_pwrite(struct Scsi_Host *instance, unsigned char *addr, int len)
+NCR5380_pwrite(struct Scsi_Host *host, unsigned char *addr, int len)
 {
-  int *ctrl = &((struct NCR5380_hostdata *)instance->hostdata)->ctrl;
-  int oldctrl = *ctrl;
   unsigned long *laddr;
-#ifdef NOT_EFFICIENT
-  int iobase = instance->io_port;
-  int dma_io = iobase & ~(0x3C0000>>2);
-#else
-  volatile unsigned char *iobase = (unsigned char *)ioaddr(instance->io_port);
-  volatile unsigned char *dma_io = (unsigned char *)((int)iobase & ~0x3C0000);
-#endif
+  void __iomem *dma = priv(host)->dma + 0x2000;
 
   if(!len) return 0;
 
-  CTRL(iobase, 0x02);
+  writeb(0x02, priv(host)->base + CTRL);
   laddr = (unsigned long *)addr;
   while(len >= 32)
   {
-    int status;
+    unsigned int status;
     unsigned long v;
-    status = STAT(iobase);
+    status = readb(priv(host)->base + STAT);
     if(status & 0x80)
       goto end;
     if(!(status & 0x40))
       continue;
-    v=*laddr++; OUT2(L(v),dma_io); OUT2(H(v),dma_io);
-    v=*laddr++; OUT2(L(v),dma_io); OUT2(H(v),dma_io);
-    v=*laddr++; OUT2(L(v),dma_io); OUT2(H(v),dma_io);
-    v=*laddr++; OUT2(L(v),dma_io); OUT2(H(v),dma_io);
-    v=*laddr++; OUT2(L(v),dma_io); OUT2(H(v),dma_io);
-    v=*laddr++; OUT2(L(v),dma_io); OUT2(H(v),dma_io);
-    v=*laddr++; OUT2(L(v),dma_io); OUT2(H(v),dma_io);
-    v=*laddr++; OUT2(L(v),dma_io); OUT2(H(v),dma_io);
+    v=*laddr++; writew(L(v), dma); writew(H(v), dma);
+    v=*laddr++; writew(L(v), dma); writew(H(v), dma);
+    v=*laddr++; writew(L(v), dma); writew(H(v), dma);
+    v=*laddr++; writew(L(v), dma); writew(H(v), dma);
+    v=*laddr++; writew(L(v), dma); writew(H(v), dma);
+    v=*laddr++; writew(L(v), dma); writew(H(v), dma);
+    v=*laddr++; writew(L(v), dma); writew(H(v), dma);
+    v=*laddr++; writew(L(v), dma); writew(H(v), dma);
     len -= 32;
     if(len == 0)
       break;
   }
 
   addr = (unsigned char *)laddr;
-  CTRL(iobase, 0x12);
+  writeb(0x12, priv(host)->base + CTRL);
+
   while(len > 0)
   {
-    int status;
-    status = STAT(iobase);
+    unsigned int status;
+    status = readb(priv(host)->base + STAT);
     if(status & 0x80)
       goto end;
     if(status & 0x40)
     {
-      OUT(*addr++, dma_io);
+      writeb(*addr++, dma);
       if(--len == 0)
         break;
     }
 
-    status = STAT(iobase);
+    status = readb(priv(host)->base + STAT);
     if(status & 0x80)
       goto end;
     if(status & 0x40)
     {
-      OUT(*addr++, dma_io);
+      writeb(*addr++, dma);
       if(--len == 0)
         break;
     }
   }
 end:
-  CTRL(iobase, oldctrl|0x40);
+  writeb(priv(host)->ctrl | 0x40, priv(host)->base + CTRL);
   return len;
 }
 
 static inline int
-NCR5380_pread(struct Scsi_Host *instance, unsigned char *addr, int len)
+NCR5380_pread(struct Scsi_Host *host, unsigned char *addr, int len)
 {
-  int *ctrl = &((struct NCR5380_hostdata *)instance->hostdata)->ctrl;
-  int oldctrl = *ctrl;
   unsigned long *laddr;
-#ifdef NOT_EFFICIENT
-  int iobase = instance->io_port;
-  int dma_io = iobase & ~(0x3C0000>>2);
-#else
-  volatile unsigned char *iobase = (unsigned char *)ioaddr(instance->io_port);
-  volatile unsigned char *dma_io = (unsigned char *)((int)iobase & ~0x3C0000);
-#endif
+  void __iomem *dma = priv(host)->dma + 0x2000;
 
   if(!len) return 0;
 
-  CTRL(iobase, 0x00);
+  writeb(0x00, priv(host)->base + CTRL);
   laddr = (unsigned long *)addr;
   while(len >= 32)
   {
-    int status;
-    status = STAT(iobase);
+    unsigned int status;
+    status = readb(priv(host)->base + STAT);
     if(status & 0x80)
       goto end;
     if(!(status & 0x40))
       continue;
-    *laddr++ = IN2(dma_io)|(IN2(dma_io)<<16);
-    *laddr++ = IN2(dma_io)|(IN2(dma_io)<<16);
-    *laddr++ = IN2(dma_io)|(IN2(dma_io)<<16);
-    *laddr++ = IN2(dma_io)|(IN2(dma_io)<<16);
-    *laddr++ = IN2(dma_io)|(IN2(dma_io)<<16);
-    *laddr++ = IN2(dma_io)|(IN2(dma_io)<<16);
-    *laddr++ = IN2(dma_io)|(IN2(dma_io)<<16);
-    *laddr++ = IN2(dma_io)|(IN2(dma_io)<<16);
+    *laddr++ = readw(dma) | (readw(dma) << 16);
+    *laddr++ = readw(dma) | (readw(dma) << 16);
+    *laddr++ = readw(dma) | (readw(dma) << 16);
+    *laddr++ = readw(dma) | (readw(dma) << 16);
+    *laddr++ = readw(dma) | (readw(dma) << 16);
+    *laddr++ = readw(dma) | (readw(dma) << 16);
+    *laddr++ = readw(dma) | (readw(dma) << 16);
+    *laddr++ = readw(dma) | (readw(dma) << 16);
     len -= 32;
     if(len == 0)
       break;
   }
 
   addr = (unsigned char *)laddr;
-  CTRL(iobase, 0x10);
+  writeb(0x10, priv(host)->base + CTRL);
+
   while(len > 0)
   {
-    int status;
-    status = STAT(iobase);
+    unsigned int status;
+    status = readb(priv(host)->base + STAT);
     if(status & 0x80)
       goto end;
     if(status & 0x40)
     {
-      *addr++ = IN(dma_io);
+      *addr++ = readb(dma);
       if(--len == 0)
         break;
     }
 
-    status = STAT(iobase);
+    status = readb(priv(host)->base + STAT);
     if(status & 0x80)
       goto end;
     if(status & 0x40)
     {
-      *addr++ = IN(dma_io);
+      *addr++ = readb(dma);
       if(--len == 0)
         break;
     }
   }
 end:
-  CTRL(iobase, oldctrl|0x40);
+  writeb(priv(host)->ctrl | 0x40, priv(host)->base + CTRL);
   return len;
 }
 
-#undef STAT
-#undef CTRL
-#undef IN
-#undef OUT
-
-#define CTRL(p,v) outb(*ctrl = (v), (p) - 577)
-
-static char cumanascsi_read(struct Scsi_Host *instance, int reg)
+static unsigned char cumanascsi_read(struct Scsi_Host *host, unsigned int reg)
 {
-	unsigned int iobase = instance->io_port;
-	int i;
-	int *ctrl = &((struct NCR5380_hostdata *)instance->hostdata)->ctrl;
+	void __iomem *base = priv(host)->base;
+	unsigned char val;
 
-	CTRL(iobase, 0);
-	i = inb(iobase + 64 + reg);
-	CTRL(iobase, 0x40);
+	writeb(0, base + CTRL);
 
-	return i;
+	val = readb(base + 0x2100 + (reg << 2));
+
+	priv(host)->ctrl = 0x40;
+	writeb(0x40, base + CTRL);
+
+	return val;
 }
 
-static void cumanascsi_write(struct Scsi_Host *instance, int reg, int value)
+static void cumanascsi_write(struct Scsi_Host *host, unsigned int reg, unsigned int value)
 {
-	int iobase = instance->io_port;
-	int *ctrl = &((struct NCR5380_hostdata *)instance->hostdata)->ctrl;
+	void __iomem *base = priv(host)->base;
 
-	CTRL(iobase, 0);
-	outb(value, iobase + 64 + reg);
-	CTRL(iobase, 0x40);
+	writeb(0, base + CTRL);
+
+	writeb(value, base + 0x2100 + (reg << 2));
+
+	priv(host)->ctrl = 0x40;
+	writeb(0x40, base + CTRL);
 }
 
-#undef CTRL
-
 #include "../NCR5380.c"
 
 static struct scsi_host_template cumanascsi_template = {
@@ -256,32 +231,46 @@
 cumanascsi1_probe(struct expansion_card *ec, const struct ecard_id *id)
 {
 	struct Scsi_Host *host;
-	int ret = -ENOMEM;
+	int ret;
 
-	host = scsi_host_alloc(&cumanascsi_template, sizeof(struct NCR5380_hostdata));
-	if (!host)
+	ret = ecard_request_resources(ec);
+	if (ret)
 		goto out;
 
-        host->io_port = ecard_address(ec, ECARD_IOC, ECARD_SLOW) + 0x800;
+	host = scsi_host_alloc(&cumanascsi_template, sizeof(struct NCR5380_hostdata));
+	if (!host) {
+		ret = -ENOMEM;
+		goto out_release;
+	}
+
+	priv(host)->base = ioremap(ecard_resource_start(ec, ECARD_RES_IOCSLOW),
+				   ecard_resource_len(ec, ECARD_RES_IOCSLOW));
+	priv(host)->dma = ioremap(ecard_resource_start(ec, ECARD_RES_MEMC),
+				  ecard_resource_len(ec, ECARD_RES_MEMC));
+	if (!priv(host)->base || !priv(host)->dma) {
+		ret = -ENOMEM;
+		goto out_unmap;
+	}
+
 	host->irq = ec->irq;
 
 	NCR5380_init(host, 0);
 
+        priv(host)->ctrl = 0;
+        writeb(0, priv(host)->base + CTRL);
+
 	host->n_io_port = 255;
 	if (!(request_region(host->io_port, host->n_io_port, "CumanaSCSI-1"))) {
 		ret = -EBUSY;
-		goto out_free;
+		goto out_unmap;
 	}
 
-        ((struct NCR5380_hostdata *)host->hostdata)->ctrl = 0;
-        outb(0x00, host->io_port - 577);
-
 	ret = request_irq(host->irq, cumanascsi_intr, IRQF_DISABLED,
 			  "CumanaSCSI-1", host);
 	if (ret) {
 		printk("scsi%d: IRQ%d not free: %d\n",
 		    host->host_no, host->irq, ret);
-		goto out_release;
+		goto out_unmap;
 	}
 
 	printk("scsi%d: at port 0x%08lx irq %d",
@@ -301,10 +290,12 @@
 
  out_free_irq:
 	free_irq(host->irq, host);
- out_release:
-	release_region(host->io_port, host->n_io_port);
- out_free:
+ out_unmap:
+	iounmap(priv(host)->base);
+	iounmap(priv(host)->dma);
 	scsi_host_put(host);
+ out_release:
+	ecard_release_resources(ec);
  out:
 	return ret;
 }
@@ -318,8 +309,10 @@
 	scsi_remove_host(host);
 	free_irq(host->irq, host);
 	NCR5380_exit(host);
-	release_region(host->io_port, host->n_io_port);
+	iounmap(priv(host)->base);
+	iounmap(priv(host)->dma);
 	scsi_host_put(host);
+	ecard_release_resources(ec);
 }
 
 static const struct ecard_id cumanascsi1_cids[] = {
diff --git a/drivers/scsi/arm/ecoscsi.c b/drivers/scsi/arm/ecoscsi.c
index 378e7af..5265a98 100644
--- a/drivers/scsi/arm/ecoscsi.c
+++ b/drivers/scsi/arm/ecoscsi.c
@@ -34,35 +34,25 @@
 #include "../scsi.h"
 #include <scsi/scsi_host.h>
 
-#define NCR5380_implementation_fields	int port, ctrl
-#define NCR5380_local_declare()		struct Scsi_Host *_instance
-#define NCR5380_setup(instance)		_instance = instance
+#define priv(host)			((struct NCR5380_hostdata *)(host)->hostdata)
 
-#define NCR5380_read(reg)		ecoscsi_read(_instance, reg)
-#define NCR5380_write(reg, value)	ecoscsi_write(_instance, reg, value)
+#define NCR5380_local_declare()		void __iomem *_base
+#define NCR5380_setup(host)		_base = priv(host)->base
+
+#define NCR5380_read(reg)		({ writeb(reg | 8, _base); readb(_base + 4); })
+#define NCR5380_write(reg, value)	({ writeb(reg | 8, _base); writeb(value, _base + 4); })
 
 #define NCR5380_intr			ecoscsi_intr
 #define NCR5380_queue_command		ecoscsi_queue_command
 #define NCR5380_proc_info		ecoscsi_proc_info
 
+#define NCR5380_implementation_fields	\
+	void __iomem *base
+
 #include "../NCR5380.h"
 
 #define ECOSCSI_PUBLIC_RELEASE 1
 
-static char ecoscsi_read(struct Scsi_Host *instance, int reg)
-{
-  int iobase = instance->io_port;
-  outb(reg | 8, iobase);
-  return inb(iobase + 1);
-}
-
-static void ecoscsi_write(struct Scsi_Host *instance, int reg, int value)
-{
-  int iobase = instance->io_port;
-  outb(reg | 8, iobase);
-  outb(value, iobase + 1);
-}
-
 /*
  * Function : ecoscsi_setup(char *str, int *ints)
  *
@@ -82,73 +72,6 @@
 	return "";
 }
 
-#if 0
-#define STAT(p) inw(p + 144)
-
-static inline int NCR5380_pwrite(struct Scsi_Host *host, unsigned char *addr,
-              int len)
-{
-  int iobase = host->io_port;
-printk("writing %p len %d\n",addr, len);
-  if(!len) return -1;
-
-  while(1)
-  {
-    int status;
-    while(((status = STAT(iobase)) & 0x100)==0);
-  }
-}
-
-static inline int NCR5380_pread(struct Scsi_Host *host, unsigned char *addr,
-              int len)
-{
-  int iobase = host->io_port;
-  int iobase2= host->io_port + 0x100;
-  unsigned char *start = addr;
-  int s;
-printk("reading %p len %d\n",addr, len);
-  outb(inb(iobase + 128), iobase + 135);
-  while(len > 0)
-  {
-    int status,b,i, timeout;
-    timeout = 0x07FFFFFF;
-    while(((status = STAT(iobase)) & 0x100)==0)
-    {
-      timeout--;
-      if(status & 0x200 || !timeout)
-      {
-        printk("status = %p\n",status);
-        outb(0, iobase + 135);
-        return 1;
-      }
-    }
-    if(len >= 128)
-    {
-      for(i=0; i<64; i++)
-      {
-        b = inw(iobase + 136);
-        *addr++ = b;
-        *addr++ = b>>8;
-      }
-      len -= 128;
-    }
-    else
-    {
-      b = inw(iobase + 136);
-      *addr ++ = b;
-      len -= 1;
-      if(len)
-        *addr ++ = b>>8;
-      len -= 1;
-    }
-  }
-  outb(0, iobase + 135);
-  printk("first bytes = %02X %02X %02X %20X %02X %02X %02X\n",*start, start[1], start[2], start[3], start[4], start[5], start[6]);
-  return 1;
-}
-#endif
-#undef STAT
-
 #define BOARD_NORMAL	0
 #define BOARD_NCR53C400	1
 
@@ -173,26 +96,37 @@
 
 static int __init ecoscsi_init(void)
 {
+	void __iomem *_base;
+	int ret;
+
+	if (!request_mem_region(0x33a0000, 4096, "ecoscsi")) {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	_base = ioremap(0x33a0000, 4096);
+	if (!_base) {
+		ret = -ENOMEM;
+		goto out_release;
+	}
+
+	NCR5380_write(MODE_REG, 0x20);		/* Is it really SCSI? */
+	if (NCR5380_read(MODE_REG) != 0x20)	/* Write to a reg.    */
+		goto out_unmap;
+
+	NCR5380_write(MODE_REG, 0x00);		/* it back.	      */
+	if (NCR5380_read(MODE_REG) != 0x00)
+		goto out_unmap;
 
 	host = scsi_host_alloc(tpnt, sizeof(struct NCR5380_hostdata));
-	if (!host)
-		return 0;
+	if (!host) {
+		ret = -ENOMEM;
+		goto out_unmap;
+	}
 
-	host->io_port = 0x80ce8000;
-	host->n_io_port = 144;
+	priv(host)->base = _base;
 	host->irq = IRQ_NONE;
 
-	if (!(request_region(host->io_port, host->n_io_port, "ecoscsi")) )
-		goto unregister_scsi;
-
-	ecoscsi_write(host, MODE_REG, 0x20);		/* Is it really SCSI? */
-	if (ecoscsi_read(host, MODE_REG) != 0x20) /* Write to a reg.    */
-		goto release_reg;
-
-	ecoscsi_write(host, MODE_REG, 0x00 );		/* it back.	      */
-	if (ecoscsi_read(host, MODE_REG) != 0x00)
-		goto release_reg;
-
 	NCR5380_init(host, 0);
 
 	printk("scsi%d: at port 0x%08lx irqs disabled", host->host_no, host->io_port);
@@ -206,24 +140,20 @@
 	scsi_scan_host(host);
 	return 0;
 
-release_reg:
-	release_region(host->io_port, host->n_io_port);
-unregister_scsi:
-	scsi_host_put(host);
-	return -ENODEV;
+ out_unmap:
+	iounmap(_base);
+ out_release:
+	release_mem_region(0x33a0000, 4096);
+ out:
+	return ret;
 }
 
 static void __exit ecoscsi_exit(void)
 {
 	scsi_remove_host(host);
-
-	if (shpnt->irq != IRQ_NONE)
-		free_irq(shpnt->irq, NULL);
 	NCR5380_exit(host);
-	if (shpnt->io_port)
-		release_region(shpnt->io_port, shpnt->n_io_port);
-
 	scsi_host_put(host);
+	release_mem_region(0x33a0000, 4096);
 	return 0;
 }
 
diff --git a/drivers/scsi/arm/oak.c b/drivers/scsi/arm/oak.c
index c21b839..849cdf8 100644
--- a/drivers/scsi/arm/oak.c
+++ b/drivers/scsi/arm/oak.c
@@ -23,15 +23,18 @@
 
 #define OAKSCSI_PUBLIC_RELEASE 1
 
-#define NCR5380_read(reg)		oakscsi_read(_instance, reg)
-#define NCR5380_write(reg, value)	oakscsi_write(_instance, reg, value)
+#define priv(host)			((struct NCR5380_hostdata *)(host)->hostdata)
+#define NCR5380_local_declare()		void __iomem *_base
+#define NCR5380_setup(host)		_base = priv(host)->base
+
+#define NCR5380_read(reg)		readb(_base + ((reg) << 2))
+#define NCR5380_write(reg, value)	writeb(value, _base + ((reg) << 2))
 #define NCR5380_intr			oakscsi_intr
 #define NCR5380_queue_command		oakscsi_queue_command
 #define NCR5380_proc_info		oakscsi_proc_info
 
-#define NCR5380_implementation_fields	int port, ctrl
-#define NCR5380_local_declare()		struct Scsi_Host *_instance
-#define NCR5380_setup(instance)		_instance = instance
+#define NCR5380_implementation_fields	\
+	void __iomem *base
 
 #define BOARD_NORMAL	0
 #define BOARD_NCR53C400	1
@@ -39,60 +42,62 @@
 #include "../NCR5380.h"
 
 #undef START_DMA_INITIATOR_RECEIVE_REG
-#define START_DMA_INITIATOR_RECEIVE_REG (7 + 128)
+#define START_DMA_INITIATOR_RECEIVE_REG	(128 + 7)
 
 const char * oakscsi_info (struct Scsi_Host *spnt)
 {
 	return "";
 }
 
-#define STAT(p)   inw(p + 144)
-extern void inswb(int from, void *to, int len);
+#define STAT	((128 + 16) << 2)
+#define DATA	((128 + 8) << 2)
 
 static inline int NCR5380_pwrite(struct Scsi_Host *instance, unsigned char *addr,
               int len)
 {
-  int iobase = instance->io_port;
+  void __iomem *base = priv(instance)->base;
+
 printk("writing %p len %d\n",addr, len);
   if(!len) return -1;
 
   while(1)
   {
     int status;
-    while(((status = STAT(iobase)) & 0x100)==0);
+    while (((status = readw(base + STAT)) & 0x100)==0);
   }
 }
 
 static inline int NCR5380_pread(struct Scsi_Host *instance, unsigned char *addr,
               int len)
 {
-  int iobase = instance->io_port;
+  void __iomem *base = priv(instance)->base;
 printk("reading %p len %d\n", addr, len);
   while(len > 0)
   {
-    int status, timeout;
+    unsigned int status, timeout;
     unsigned long b;
     
     timeout = 0x01FFFFFF;
     
-    while(((status = STAT(iobase)) & 0x100)==0)
+    while (((status = readw(base + STAT)) & 0x100)==0)
     {
       timeout--;
       if(status & 0x200 || !timeout)
       {
-        printk("status = %08X\n",status);
+        printk("status = %08X\n", status);
         return 1;
       }
     }
+
     if(len >= 128)
     {
-      inswb(iobase + 136, addr, 128);
+      readsw(base + DATA, addr, 128);
       addr += 128;
       len -= 128;
     }
     else
     {
-      b = (unsigned long) inw(iobase + 136);
+      b = (unsigned long) readw(base + DATA);
       *addr ++ = b;
       len -= 1;
       if(len)
@@ -103,10 +108,8 @@
   return 0;
 }
 
-#define oakscsi_read(instance,reg)	(inb((instance)->io_port + (reg)))
-#define oakscsi_write(instance,reg,val)	(outb((val), (instance)->io_port + (reg)))
-
 #undef STAT
+#undef DATA
 
 #include "../NCR5380.c"
 
@@ -132,18 +135,26 @@
 	struct Scsi_Host *host;
 	int ret = -ENOMEM;
 
-	host = scsi_host_alloc(&oakscsi_template, sizeof(struct NCR5380_hostdata));
-	if (!host)
+	ret = ecard_request_resources(ec);
+	if (ret)
 		goto out;
 
-	host->io_port = ecard_address(ec, ECARD_MEMC, 0);
+	host = scsi_host_alloc(&oakscsi_template, sizeof(struct NCR5380_hostdata));
+	if (!host) {
+		ret = -ENOMEM;
+		goto release;
+	}
+
+	priv(host)->base = ioremap(ecard_resource_start(ec, ECARD_RES_MEMC),
+				   ecard_resource_len(ec, ECARD_RES_MEMC));
+	if (!priv(host)->base) {
+		ret = -ENOMEM;
+		goto unreg;
+	}
+
 	host->irq = IRQ_NONE;
 	host->n_io_port = 255;
 
-	ret = -EBUSY;
-	if (!request_region (host->io_port, host->n_io_port, "Oak SCSI"))
-		goto unreg;
-
 	NCR5380_init(host, 0);
 
 	printk("scsi%d: at port 0x%08lx irqs disabled",
@@ -156,15 +167,17 @@
 
 	ret = scsi_add_host(host, &ec->dev);
 	if (ret)
-		goto out_release;
+		goto out_unmap;
 
 	scsi_scan_host(host);
 	goto out;
 
- out_release:
-	release_region(host->io_port, host->n_io_port);
+ out_unmap:
+	iounmap(priv(host)->base);
  unreg:
 	scsi_host_put(host);
+ release:
+	ecard_release_resources(ec);
  out:
 	return ret;
 }
@@ -177,8 +190,9 @@
 	scsi_remove_host(host);
 
 	NCR5380_exit(host);
-	release_region(host->io_port, host->n_io_port);
+	iounmap(priv(host)->base);
 	scsi_host_put(host);
+	ecard_release_resources(ec);
 }
 
 static const struct ecard_id oakscsi_cids[] = {
diff --git a/drivers/serial/imx.c b/drivers/serial/imx.c
index e42faa4..dc19671 100644
--- a/drivers/serial/imx.c
+++ b/drivers/serial/imx.c
@@ -1114,8 +1114,8 @@
 
 static void __exit imx_serial_exit(void)
 {
-	uart_unregister_driver(&imx_reg);
 	platform_driver_unregister(&serial_imx_driver);
+	uart_unregister_driver(&imx_reg);
 }
 
 module_init(imx_serial_init);
diff --git a/drivers/serial/s3c2410.c b/drivers/serial/s3c2410.c
index 10bc020..3f26c4b 100644
--- a/drivers/serial/s3c2410.c
+++ b/drivers/serial/s3c2410.c
@@ -78,7 +78,7 @@
 
 #include <asm/hardware.h>
 
-#include <asm/arch/regs-serial.h>
+#include <asm/plat-s3c/regs-serial.h>
 #include <asm/arch/regs-gpio.h>
 
 /* structures */
diff --git a/include/asm-arm/arch-at91/at91_mci.h b/include/asm-arm/arch-at91/at91_mci.h
index 40a9876..c2e11cc 100644
--- a/include/asm-arm/arch-at91/at91_mci.h
+++ b/include/asm-arm/arch-at91/at91_mci.h
@@ -26,6 +26,9 @@
 #define AT91_MCI_MR		0x04		/* Mode Register */
 #define		AT91_MCI_CLKDIV		(0xff  <<  0)	/* Clock Divider */
 #define		AT91_MCI_PWSDIV		(7     <<  8)	/* Power Saving Divider */
+#define		AT91_MCI_RDPROOF	(1     << 11)	/* Read Proof Enable [SAM926[03] only] */
+#define		AT91_MCI_WRPROOF	(1     << 12)	/* Write Proof Enable [SAM926[03] only] */
+#define		AT91_MCI_PDCFBYTE	(1     << 13)	/* PDC Force Byte Transfer [SAM926[03] only] */
 #define		AT91_MCI_PDCPADV	(1     << 14)	/* PDC Padding Value */
 #define		AT91_MCI_PDCMODE	(1     << 15)	/* PDC-orientated Mode */
 #define		AT91_MCI_BLKLEN		(0xfff << 18)	/* Data Block Length */
diff --git a/include/asm-arm/arch-mxc/board-mx31ads.h b/include/asm-arm/arch-mxc/board-mx31ads.h
new file mode 100644
index 0000000..be29b83
--- /dev/null
+++ b/include/asm-arm/arch-mxc/board-mx31ads.h
@@ -0,0 +1,142 @@
+/*
+ * Copyright 2005-2007 Freescale Semiconductor, Inc. All Rights Reserved.
+ */
+
+/*
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __ASM_ARCH_MXC_BOARD_MX31ADS_H__
+#define __ASM_ARCH_MXC_BOARD_MX31ADS_H__
+
+/*!
+ * @name PBC Controller parameters
+ */
+/*! @{ */
+/*!
+ * Base address of PBC controller
+ */
+#define PBC_BASE_ADDRESS        IO_ADDRESS(CS4_BASE_ADDR)
+/* Offsets for the PBC Controller register */
+/*!
+ * PBC Board status register offset
+ */
+#define PBC_BSTAT               0x000002
+/*!
+ * PBC Board control register 1 set address.
+ */
+#define PBC_BCTRL1_SET          0x000004
+/*!
+ * PBC Board control register 1 clear address.
+ */
+#define PBC_BCTRL1_CLEAR        0x000006
+/*!
+ * PBC Board control register 2 set address.
+ */
+#define PBC_BCTRL2_SET          0x000008
+/*!
+ * PBC Board control register 2 clear address.
+ */
+#define PBC_BCTRL2_CLEAR        0x00000A
+/*!
+ * PBC Board control register 3 set address.
+ */
+#define PBC_BCTRL3_SET          0x00000C
+/*!
+ * PBC Board control register 3 clear address.
+ */
+#define PBC_BCTRL3_CLEAR        0x00000E
+/*!
+ * PBC Board control register 4 set address.
+ */
+#define PBC_BCTRL4_SET          0x000010
+/*!
+ * PBC Board control register 4 clear address.
+ */
+#define PBC_BCTRL4_CLEAR        0x000012
+/*!
+ * PBC Board status register 1.
+ */
+#define PBC_BSTAT1              0x000014
+/*!
+ * PBC Board interrupt status register.
+ */
+#define PBC_INTSTATUS           0x000016
+/*!
+ * PBC Board interrupt current status register.
+ */
+#define PBC_INTCURR_STATUS      0x000018
+/*!
+ * PBC Interrupt mask register set address.
+ */
+#define PBC_INTMASK_SET         0x00001A
+/*!
+ * PBC Interrupt mask register clear address.
+ */
+#define PBC_INTMASK_CLEAR       0x00001C
+
+/*!
+ * External UART A.
+ */
+#define PBC_SC16C652_UARTA      0x010000
+/*!
+ * External UART B.
+ */
+#define PBC_SC16C652_UARTB      0x010010
+/*!
+ * Ethernet Controller IO base address.
+ */
+#define PBC_CS8900A_IOBASE      0x020000
+/*!
+ * Ethernet Controller Memory base address.
+ */
+#define PBC_CS8900A_MEMBASE     0x021000
+/*!
+ * Ethernet Controller DMA base address.
+ */
+#define PBC_CS8900A_DMABASE     0x022000
+/*!
+ * External chip select 0.
+ */
+#define PBC_XCS0                0x040000
+/*!
+ * LCD Display enable.
+ */
+#define PBC_LCD_EN_B            0x060000
+/*!
+ * Code test debug enable.
+ */
+#define PBC_CODE_B              0x070000
+/*!
+ * PSRAM memory select.
+ */
+#define PBC_PSRAM_B             0x5000000
+
+#define PBC_INTSTATUS_REG	(PBC_INTSTATUS + PBC_BASE_ADDRESS)
+#define PBC_INTCURR_STATUS_REG	(PBC_INTCURR_STATUS + PBC_BASE_ADDRESS)
+#define PBC_INTMASK_SET_REG	(PBC_INTMASK_SET + PBC_BASE_ADDRESS)
+#define PBC_INTMASK_CLEAR_REG	(PBC_INTMASK_CLEAR + PBC_BASE_ADDRESS)
+#define EXPIO_PARENT_INT	IOMUX_TO_IRQ(MX31_PIN_GPIO1_4)
+
+#define EXPIO_INT_LOW_BAT	(MXC_EXP_IO_BASE + 0)
+#define EXPIO_INT_PB_IRQ	(MXC_EXP_IO_BASE + 1)
+#define EXPIO_INT_OTG_FS_OVR	(MXC_EXP_IO_BASE + 2)
+#define EXPIO_INT_FSH_OVR	(MXC_EXP_IO_BASE + 3)
+#define EXPIO_INT_RES4		(MXC_EXP_IO_BASE + 4)
+#define EXPIO_INT_RES5		(MXC_EXP_IO_BASE + 5)
+#define EXPIO_INT_RES6		(MXC_EXP_IO_BASE + 6)
+#define EXPIO_INT_RES7		(MXC_EXP_IO_BASE + 7)
+#define EXPIO_INT_ENET_INT	(MXC_EXP_IO_BASE + 8)
+#define EXPIO_INT_OTG_FS_INT	(MXC_EXP_IO_BASE + 9)
+#define EXPIO_INT_XUART_INTA	(MXC_EXP_IO_BASE + 10)
+#define EXPIO_INT_XUART_INTB	(MXC_EXP_IO_BASE + 11)
+#define EXPIO_INT_SYNTH_IRQ	(MXC_EXP_IO_BASE + 12)
+#define EXPIO_INT_CE_INT1	(MXC_EXP_IO_BASE + 13)
+#define EXPIO_INT_CE_INT2	(MXC_EXP_IO_BASE + 14)
+#define EXPIO_INT_RES15		(MXC_EXP_IO_BASE + 15)
+
+#define MXC_MAX_EXP_IO_LINES	16
+
+#endif				/* __ASM_ARCH_MXC_BOARD_MX31ADS_H__ */
diff --git a/include/asm-arm/arch-mxc/common.h b/include/asm-arm/arch-mxc/common.h
new file mode 100644
index 0000000..23b4350
--- /dev/null
+++ b/include/asm-arm/arch-mxc/common.h
@@ -0,0 +1,20 @@
+/*
+ * Copyright 2004-2007 Freescale Semiconductor, Inc. All Rights Reserved.
+ */
+
+/*
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __ASM_ARCH_MXC_COMMON_H__
+#define __ASM_ARCH_MXC_COMMON_H__
+
+struct sys_timer;
+
+extern void mxc_map_io(void);
+extern void mxc_init_irq(void);
+extern struct sys_timer mxc_timer;
+
+#endif
diff --git a/include/asm-arm/arch-mxc/dma.h b/include/asm-arm/arch-mxc/dma.h
new file mode 100644
index 0000000..65e639d
--- /dev/null
+++ b/include/asm-arm/arch-mxc/dma.h
@@ -0,0 +1,21 @@
+/*
+ * Copyright 2004-2007 Freescale Semiconductor, Inc. All Rights Reserved.
+ */
+
+/*
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __ASM_ARCH_MXC_DMA_H__
+#define __ASM_ARCH_MXC_DMA_H__
+
+/*!
+ * @file dma.h
+ * @brief This file contains Unified DMA API for all MXC platforms.
+ * The API is platform independent.
+ *
+ * @ingroup SDMA
+ */
+#endif
diff --git a/include/asm-arm/arch-mxc/entry-macro.S b/include/asm-arm/arch-mxc/entry-macro.S
new file mode 100644
index 0000000..b542433
--- /dev/null
+++ b/include/asm-arm/arch-mxc/entry-macro.S
@@ -0,0 +1,39 @@
+/*
+ *  Copyright (C) 2007 Lennert Buytenhek <buytenh@wantstofly.org>
+ *  Copyright 2004-2007 Freescale Semiconductor, Inc. All Rights Reserved.
+ */
+
+/*
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+	@ this macro disables fast irq (not implemented)
+	.macro	disable_fiq
+	.endm
+
+	.macro  get_irqnr_preamble, base, tmp
+	.endm
+
+	.macro  arch_ret_to_user, tmp1, tmp2
+	.endm
+
+	@ this macro checks which interrupt occured
+	@ and returns its number in irqnr
+	@ and returns if an interrupt occured in irqstat
+	.macro	get_irqnr_and_base, irqnr, irqstat, base, tmp
+	ldr	\base, =AVIC_IO_ADDRESS(AVIC_BASE_ADDR)
+	@ Load offset & priority of the highest priority
+	@ interrupt pending from AVIC_NIVECSR
+	ldr	\irqstat, [\base, #0x40]
+	@ Shift to get the decoded IRQ number, using ASR so
+	@ 'no interrupt pending' becomes 0xffffffff
+	mov	\irqnr, \irqstat, asr #16
+	@ set zero flag if IRQ + 1 == 0
+	adds	\tmp, \irqnr, #1
+	.endm
+
+	@ irq priority table (not used)
+	.macro	irq_prio_table
+	.endm
diff --git a/include/asm-arm/arch-mxc/hardware.h b/include/asm-arm/arch-mxc/hardware.h
new file mode 100644
index 0000000..3c09b92
--- /dev/null
+++ b/include/asm-arm/arch-mxc/hardware.h
@@ -0,0 +1,52 @@
+/*
+ *  Copyright 2004-2007 Freescale Semiconductor, Inc. All Rights Reserved.
+ */
+
+/*
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*!
+ * @file hardware.h
+ * @brief This file contains the hardware definitions of the board.
+ *
+ * @ingroup System
+ */
+#ifndef __ASM_ARCH_MXC_HARDWARE_H__
+#define __ASM_ARCH_MXC_HARDWARE_H__
+
+#include <asm/sizes.h>
+
+#include <asm/arch/mx31.h>
+
+#include <asm/arch/mxc.h>
+
+#define MXC_MAX_GPIO_LINES      (GPIO_NUM_PIN * GPIO_PORT_NUM)
+
+/*
+ * ---------------------------------------------------------------------------
+ * Board specific defines
+ * ---------------------------------------------------------------------------
+ */
+#define MXC_EXP_IO_BASE         (MXC_GPIO_INT_BASE + MXC_MAX_GPIO_LINES)
+
+#include <asm/arch/board-mx31ads.h>
+
+#ifndef MXC_MAX_EXP_IO_LINES
+#define MXC_MAX_EXP_IO_LINES 0
+#endif
+
+#define MXC_MAX_VIRTUAL_INTS	16
+#define MXC_VIRTUAL_INTS_BASE	(MXC_EXP_IO_BASE + MXC_MAX_EXP_IO_LINES)
+#define MXC_SDIO1_CARD_IRQ	MXC_VIRTUAL_INTS_BASE
+#define MXC_SDIO2_CARD_IRQ	(MXC_VIRTUAL_INTS_BASE + 1)
+#define MXC_SDIO3_CARD_IRQ	(MXC_VIRTUAL_INTS_BASE + 2)
+
+#define MXC_MAX_INTS            (MXC_MAX_INT_LINES + \
+                                MXC_MAX_GPIO_LINES + \
+                                MXC_MAX_EXP_IO_LINES + \
+                                MXC_MAX_VIRTUAL_INTS)
+
+#endif				/* __ASM_ARCH_MXC_HARDWARE_H__ */
diff --git a/include/asm-arm/arch-mxc/io.h b/include/asm-arm/arch-mxc/io.h
new file mode 100644
index 0000000..cf6c83a
--- /dev/null
+++ b/include/asm-arm/arch-mxc/io.h
@@ -0,0 +1,33 @@
+/*
+ *  Copyright 2004-2007 Freescale Semiconductor, Inc. All Rights Reserved.
+ */
+
+/*
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*!
+ * @file io.h
+ * @brief This file contains some memory mapping macros.
+ * @note There is no real ISA or PCI buses. But have to define these macros
+ * for some drivers to compile.
+ *
+ * @ingroup System
+ */
+
+#ifndef __ASM_ARCH_MXC_IO_H__
+#define __ASM_ARCH_MXC_IO_H__
+
+/*! Allow IO space to be anywhere in the memory */
+#define IO_SPACE_LIMIT 0xffffffff
+
+/*!
+ * io address mapping macro
+ */
+#define __io(a)			((void __iomem *)(a))
+
+#define __mem_pci(a)		(a)
+
+#endif
diff --git a/include/asm-arm/arch-mxc/irqs.h b/include/asm-arm/arch-mxc/irqs.h
new file mode 100644
index 0000000..e4686c6
--- /dev/null
+++ b/include/asm-arm/arch-mxc/irqs.h
@@ -0,0 +1,38 @@
+/*
+ *  Copyright 2004-2007 Freescale Semiconductor, Inc. All Rights Reserved.
+ */
+
+/*
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __ASM_ARCH_MXC_IRQS_H__
+#define __ASM_ARCH_MXC_IRQS_H__
+
+#include <asm/hardware.h>
+
+/*!
+ * @file irqs.h
+ * @brief This file defines the number of normal interrupts and fast interrupts
+ *
+ * @ingroup Interrupt
+ */
+
+#define MXC_IRQ_TO_EXPIO(irq)	((irq) - MXC_EXP_IO_BASE)
+
+#define MXC_IRQ_TO_GPIO(irq)	((irq) - MXC_GPIO_INT_BASE)
+#define MXC_GPIO_TO_IRQ(x)	(MXC_GPIO_INT_BASE + x)
+
+/*!
+ * Number of normal interrupts
+ */
+#define NR_IRQS		MXC_MAX_INTS
+
+/*!
+ * Number of fast interrupts
+ */
+#define NR_FIQS		MXC_MAX_INTS
+
+#endif				/* __ASM_ARCH_MXC_IRQS_H__ */
diff --git a/include/asm-arm/arch-mxc/memory.h b/include/asm-arm/arch-mxc/memory.h
new file mode 100644
index 0000000..c89aac8
--- /dev/null
+++ b/include/asm-arm/arch-mxc/memory.h
@@ -0,0 +1,36 @@
+/*
+ * Copyright 2004-2007 Freescale Semiconductor, Inc. All Rights Reserved.
+ */
+
+/*
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __ASM_ARCH_MXC_MEMORY_H__
+#define __ASM_ARCH_MXC_MEMORY_H__
+
+#include <asm/hardware.h>
+
+/*!
+ * @file memory.h
+ * @brief This file contains macros needed by the Linux kernel and drivers.
+ *
+ * @ingroup Memory
+ */
+
+/*!
+ * Virtual view <-> DMA view memory address translations
+ * This macro is used to translate the virtual address to an address
+ * suitable to be passed to set_dma_addr()
+ */
+#define __virt_to_bus(a)	__virt_to_phys(a)
+
+/*!
+ * Used to convert an address for DMA operations to an address that the
+ * kernel can use.
+ */
+#define __bus_to_virt(a)	__phys_to_virt(a)
+
+#endif				/* __ASM_ARCH_MXC_MEMORY_H__ */
diff --git a/include/asm-arm/arch-mxc/mx31.h b/include/asm-arm/arch-mxc/mx31.h
new file mode 100644
index 0000000..85c49c9
--- /dev/null
+++ b/include/asm-arm/arch-mxc/mx31.h
@@ -0,0 +1,335 @@
+/*
+ * Copyright 2004-2007 Freescale Semiconductor, Inc. All Rights Reserved.
+ */
+
+/*
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __ASM_ARCH_MXC_MX31_H__
+#define __ASM_ARCH_MXC_MX31_H__
+
+#ifndef __ASM_ARCH_MXC_HARDWARE_H__
+#error "Do not include directly."
+#endif
+
+/*!
+ * defines the hardware clock tick rate
+ */
+#define CLOCK_TICK_RATE		16625000
+
+/*
+ * MX31 memory map:
+ *
+ * Virt		Phys		Size	What
+ * ---------------------------------------------------------------------------
+ * F8000000	1FFC0000	16K	IRAM
+ * F9000000	30000000	256M	L2CC
+ * FC000000	43F00000	1M	AIPS 1
+ * FC100000	50000000	1M	SPBA
+ * FC200000	53F00000	1M	AIPS 2
+ * FC500000	60000000	128M	ROMPATCH
+ * FC400000	68000000	128M	AVIC
+ *         	70000000	256M	IPU (MAX M2)
+ *         	80000000	256M	CSD0 SDRAM/DDR
+ *         	90000000	256M	CSD1 SDRAM/DDR
+ *         	A0000000	128M	CS0 Flash
+ *         	A8000000	128M	CS1 Flash
+ *         	B0000000	32M	CS2
+ *         	B2000000	32M	CS3
+ * F4000000	B4000000	32M	CS4
+ *         	B6000000	32M	CS5
+ * FC320000	B8000000	64K	NAND, SDRAM, WEIM, M3IF, EMI controllers
+ *         	C0000000	64M	PCMCIA/CF
+ */
+
+#define CS0_BASE_ADDR		0xA0000000
+#define CS1_BASE_ADDR		0xA8000000
+#define CS2_BASE_ADDR		0xB0000000
+#define CS3_BASE_ADDR		0xB2000000
+
+#define CS4_BASE_ADDR		0xB4000000
+#define CS4_BASE_ADDR_VIRT	0xF4000000
+#define CS4_SIZE		SZ_32M
+
+#define CS5_BASE_ADDR		0xB6000000
+#define PCMCIA_MEM_BASE_ADDR	0xBC000000
+
+/*
+ * IRAM
+ */
+#define IRAM_BASE_ADDR		0x1FFC0000	/* internal ram */
+#define IRAM_BASE_ADDR_VIRT	0xF8000000
+#define IRAM_SIZE		SZ_16K
+
+/*
+ * L2CC
+ */
+#define L2CC_BASE_ADDR		0x30000000
+#define L2CC_BASE_ADDR_VIRT	0xF9000000
+#define L2CC_SIZE		SZ_1M
+
+/*
+ * AIPS 1
+ */
+#define AIPS1_BASE_ADDR		0x43F00000
+#define AIPS1_BASE_ADDR_VIRT	0xFC000000
+#define AIPS1_SIZE		SZ_1M
+
+#define MAX_BASE_ADDR		(AIPS1_BASE_ADDR + 0x00004000)
+#define EVTMON_BASE_ADDR	(AIPS1_BASE_ADDR + 0x00008000)
+#define CLKCTL_BASE_ADDR	(AIPS1_BASE_ADDR + 0x0000C000)
+#define ETB_SLOT4_BASE_ADDR	(AIPS1_BASE_ADDR + 0x00010000)
+#define ETB_SLOT5_BASE_ADDR	(AIPS1_BASE_ADDR + 0x00014000)
+#define ECT_CTIO_BASE_ADDR	(AIPS1_BASE_ADDR + 0x00018000)
+#define I2C_BASE_ADDR		(AIPS1_BASE_ADDR + 0x00080000)
+#define I2C3_BASE_ADDR		(AIPS1_BASE_ADDR + 0x00084000)
+#define OTG_BASE_ADDR		(AIPS1_BASE_ADDR + 0x00088000)
+#define ATA_BASE_ADDR		(AIPS1_BASE_ADDR + 0x0008C000)
+#define UART1_BASE_ADDR 	(AIPS1_BASE_ADDR + 0x00090000)
+#define UART2_BASE_ADDR 	(AIPS1_BASE_ADDR + 0x00094000)
+#define I2C2_BASE_ADDR		(AIPS1_BASE_ADDR + 0x00098000)
+#define OWIRE_BASE_ADDR 	(AIPS1_BASE_ADDR + 0x0009C000)
+#define SSI1_BASE_ADDR		(AIPS1_BASE_ADDR + 0x000A0000)
+#define CSPI1_BASE_ADDR 	(AIPS1_BASE_ADDR + 0x000A4000)
+#define KPP_BASE_ADDR		(AIPS1_BASE_ADDR + 0x000A8000)
+#define IOMUXC_BASE_ADDR	(AIPS1_BASE_ADDR + 0x000AC000)
+#define UART4_BASE_ADDR 	(AIPS1_BASE_ADDR + 0x000B0000)
+#define UART5_BASE_ADDR 	(AIPS1_BASE_ADDR + 0x000B4000)
+#define ECT_IP1_BASE_ADDR	(AIPS1_BASE_ADDR + 0x000B8000)
+#define ECT_IP2_BASE_ADDR	(AIPS1_BASE_ADDR + 0x000BC000)
+
+/*
+ * SPBA global module enabled #0
+ */
+#define SPBA0_BASE_ADDR 	0x50000000
+#define SPBA0_BASE_ADDR_VIRT	0xFC100000
+#define SPBA0_SIZE		SZ_1M
+
+#define MMC_SDHC1_BASE_ADDR	(SPBA0_BASE_ADDR + 0x00004000)
+#define MMC_SDHC2_BASE_ADDR	(SPBA0_BASE_ADDR + 0x00008000)
+#define UART3_BASE_ADDR 	(SPBA0_BASE_ADDR + 0x0000C000)
+#define CSPI2_BASE_ADDR 	(SPBA0_BASE_ADDR + 0x00010000)
+#define SSI2_BASE_ADDR		(SPBA0_BASE_ADDR + 0x00014000)
+#define SIM1_BASE_ADDR		(SPBA0_BASE_ADDR + 0x00018000)
+#define IIM_BASE_ADDR		(SPBA0_BASE_ADDR + 0x0001C000)
+#define ATA_DMA_BASE_ADDR	(SPBA0_BASE_ADDR + 0x00020000)
+#define MSHC1_BASE_ADDR		(SPBA0_BASE_ADDR + 0x00024000)
+#define MSHC2_BASE_ADDR		(SPBA0_BASE_ADDR + 0x00024000)
+#define SPBA_CTRL_BASE_ADDR	(SPBA0_BASE_ADDR + 0x0003C000)
+
+/*
+ * AIPS 2
+ */
+#define AIPS2_BASE_ADDR		0x53F00000
+#define AIPS2_BASE_ADDR_VIRT	0xFC200000
+#define AIPS2_SIZE		SZ_1M
+#define CCM_BASE_ADDR		(AIPS2_BASE_ADDR + 0x00080000)
+#define CSPI3_BASE_ADDR		(AIPS2_BASE_ADDR + 0x00084000)
+#define FIRI_BASE_ADDR		(AIPS2_BASE_ADDR + 0x0008C000)
+#define GPT1_BASE_ADDR		(AIPS2_BASE_ADDR + 0x00090000)
+#define EPIT1_BASE_ADDR		(AIPS2_BASE_ADDR + 0x00094000)
+#define EPIT2_BASE_ADDR		(AIPS2_BASE_ADDR + 0x00098000)
+#define GPIO3_BASE_ADDR		(AIPS2_BASE_ADDR + 0x000A4000)
+#define SCC_BASE_ADDR		(AIPS2_BASE_ADDR + 0x000AC000)
+#define SCM_BASE_ADDR		(AIPS2_BASE_ADDR + 0x000AE000)
+#define SMN_BASE_ADDR		(AIPS2_BASE_ADDR + 0x000AF000)
+#define RNGA_BASE_ADDR		(AIPS2_BASE_ADDR + 0x000B0000)
+#define IPU_CTRL_BASE_ADDR	(AIPS2_BASE_ADDR + 0x000C0000)
+#define AUDMUX_BASE_ADDR	(AIPS2_BASE_ADDR + 0x000C4000)
+#define MPEG4_ENC_BASE_ADDR	(AIPS2_BASE_ADDR + 0x000C8000)
+#define GPIO1_BASE_ADDR		(AIPS2_BASE_ADDR + 0x000CC000)
+#define GPIO2_BASE_ADDR		(AIPS2_BASE_ADDR + 0x000D0000)
+#define SDMA_BASE_ADDR		(AIPS2_BASE_ADDR + 0x000D4000)
+#define RTC_BASE_ADDR		(AIPS2_BASE_ADDR + 0x000D8000)
+#define WDOG_BASE_ADDR		(AIPS2_BASE_ADDR + 0x000DC000)
+#define PWM_BASE_ADDR		(AIPS2_BASE_ADDR + 0x000E0000)
+#define RTIC_BASE_ADDR		(AIPS2_BASE_ADDR + 0x000EC000)
+
+/*
+ * ROMP and AVIC
+ */
+#define ROMP_BASE_ADDR		0x60000000
+#define ROMP_BASE_ADDR_VIRT	0xFC500000
+#define ROMP_SIZE		SZ_1M
+
+#define AVIC_BASE_ADDR		0x68000000
+#define AVIC_BASE_ADDR_VIRT	0xFC400000
+#define AVIC_SIZE		SZ_1M
+
+/*
+ * NAND, SDRAM, WEIM, M3IF, EMI controllers
+ */
+#define X_MEMC_BASE_ADDR	0xB8000000
+#define X_MEMC_BASE_ADDR_VIRT	0xFC320000
+#define X_MEMC_SIZE		SZ_64K
+
+#define NFC_BASE_ADDR		(X_MEMC_BASE_ADDR + 0x0000)
+#define ESDCTL_BASE_ADDR	(X_MEMC_BASE_ADDR + 0x1000)
+#define WEIM_BASE_ADDR		(X_MEMC_BASE_ADDR + 0x2000)
+#define M3IF_BASE_ADDR		(X_MEMC_BASE_ADDR + 0x3000)
+#define EMI_CTL_BASE_ADDR	(X_MEMC_BASE_ADDR + 0x4000)
+#define PCMCIA_CTL_BASE_ADDR	EMI_CTL_BASE_ADDR
+
+/*
+ * Memory regions and CS
+ */
+#define IPU_MEM_BASE_ADDR	0x70000000
+#define CSD0_BASE_ADDR		0x80000000
+#define CSD1_BASE_ADDR		0x90000000
+#define CS0_BASE_ADDR		0xA0000000
+#define CS1_BASE_ADDR		0xA8000000
+#define CS2_BASE_ADDR		0xB0000000
+#define CS3_BASE_ADDR		0xB2000000
+
+#define CS4_BASE_ADDR		0xB4000000
+#define CS4_BASE_ADDR_VIRT	0xF4000000
+#define CS4_SIZE		SZ_32M
+
+#define CS5_BASE_ADDR		0xB6000000
+#define PCMCIA_MEM_BASE_ADDR	0xBC000000
+
+/*!
+ * This macro defines the physical to virtual address mapping for all the
+ * peripheral modules. It is used by passing in the physical address as x
+ * and returning the virtual address. If the physical address is not mapped,
+ * it returns 0xDEADBEEF
+ */
+#define IO_ADDRESS(x)   \
+	(((x >= IRAM_BASE_ADDR) && (x < (IRAM_BASE_ADDR + IRAM_SIZE))) ? IRAM_IO_ADDRESS(x):\
+	((x >= L2CC_BASE_ADDR) && (x < (L2CC_BASE_ADDR + L2CC_SIZE))) ? L2CC_IO_ADDRESS(x):\
+	((x >= AIPS1_BASE_ADDR) && (x < (AIPS1_BASE_ADDR + AIPS1_SIZE))) ? AIPS1_IO_ADDRESS(x):\
+	((x >= SPBA0_BASE_ADDR) && (x < (SPBA0_BASE_ADDR + SPBA0_SIZE))) ? SPBA0_IO_ADDRESS(x):\
+	((x >= AIPS2_BASE_ADDR) && (x < (AIPS2_BASE_ADDR + AIPS2_SIZE))) ? AIPS2_IO_ADDRESS(x):\
+	((x >= ROMP_BASE_ADDR) && (x < (ROMP_BASE_ADDR + ROMP_SIZE))) ? ROMP_IO_ADDRESS(x):\
+	((x >= AVIC_BASE_ADDR) && (x < (AVIC_BASE_ADDR + AVIC_SIZE))) ? AVIC_IO_ADDRESS(x):\
+	((x >= CS4_BASE_ADDR) && (x < (CS4_BASE_ADDR + CS4_SIZE))) ? CS4_IO_ADDRESS(x):\
+	((x >= X_MEMC_BASE_ADDR) && (x < (X_MEMC_BASE_ADDR + X_MEMC_SIZE))) ? X_MEMC_IO_ADDRESS(x):\
+	0xDEADBEEF)
+
+/*
+ * define the address mapping macros: in physical address order
+ */
+
+#define IRAM_IO_ADDRESS(x)  \
+	(((x) - IRAM_BASE_ADDR) + IRAM_BASE_ADDR_VIRT)
+
+#define L2CC_IO_ADDRESS(x)  \
+	(((x) - L2CC_BASE_ADDR) + L2CC_BASE_ADDR_VIRT)
+
+#define AIPS1_IO_ADDRESS(x)  \
+	(((x) - AIPS1_BASE_ADDR) + AIPS1_BASE_ADDR_VIRT)
+
+#define SPBA0_IO_ADDRESS(x)  \
+	(((x) - SPBA0_BASE_ADDR) + SPBA0_BASE_ADDR_VIRT)
+
+#define AIPS2_IO_ADDRESS(x)  \
+	(((x) - AIPS2_BASE_ADDR) + AIPS2_BASE_ADDR_VIRT)
+
+#define ROMP_IO_ADDRESS(x)  \
+	(((x) - ROMP_BASE_ADDR) + ROMP_BASE_ADDR_VIRT)
+
+#define AVIC_IO_ADDRESS(x)  \
+	(((x) - AVIC_BASE_ADDR) + AVIC_BASE_ADDR_VIRT)
+
+#define CS4_IO_ADDRESS(x)  \
+	(((x) - CS4_BASE_ADDR) + CS4_BASE_ADDR_VIRT)
+
+#define X_MEMC_IO_ADDRESS(x)  \
+	(((x) - X_MEMC_BASE_ADDR) + X_MEMC_BASE_ADDR_VIRT)
+
+#define PCMCIA_IO_ADDRESS(x) \
+	(((x) - X_MEMC_BASE_ADDR) + X_MEMC_BASE_ADDR_VIRT)
+
+/* Start of physical RAM - On many MX31 platforms, this is the first SDRAM bank (CSD0) */
+#define PHYS_OFFSET             CSD0_BASE_ADDR
+
+/*
+ * Interrupt numbers
+ */
+#define MXC_INT_PEN_ADS7843	0
+#define MXC_INT_RESV1		1
+#define MXC_INT_CS8900A		2
+#define MXC_INT_I2C3		3
+#define MXC_INT_I2C2		4
+#define MXC_INT_MPEG4_ENCODER	5
+#define MXC_INT_RTIC		6
+#define MXC_INT_FIRI		7
+#define MXC_INT_MMC_SDHC2	8
+#define MXC_INT_MMC_SDHC1	9
+#define MXC_INT_I2C		10
+#define MXC_INT_SSI2		11
+#define MXC_INT_SSI1		12
+#define MXC_INT_CSPI2		13
+#define MXC_INT_CSPI1		14
+#define MXC_INT_ATA		15
+#define MXC_INT_MBX		16
+#define MXC_INT_CSPI3		17
+#define MXC_INT_UART3		18
+#define MXC_INT_IIM		19
+#define MXC_INT_SIM2		20
+#define MXC_INT_SIM1		21
+#define MXC_INT_RNGA		22
+#define MXC_INT_EVTMON		23
+#define MXC_INT_KPP		24
+#define MXC_INT_RTC		25
+#define MXC_INT_PWM		26
+#define MXC_INT_EPIT2		27
+#define MXC_INT_EPIT1		28
+#define MXC_INT_GPT		29
+#define MXC_INT_RESV30		30
+#define MXC_INT_RESV31		31
+#define MXC_INT_UART2		32
+#define MXC_INT_NANDFC		33
+#define MXC_INT_SDMA		34
+#define MXC_INT_USB1		35
+#define MXC_INT_USB2		36
+#define MXC_INT_USB3		37
+#define MXC_INT_USB4		38
+#define MXC_INT_MSHC1		39
+#define MXC_INT_MSHC2		40
+#define MXC_INT_IPU_ERR		41
+#define MXC_INT_IPU_SYN		42
+#define MXC_INT_RESV43		43
+#define MXC_INT_RESV44		44
+#define MXC_INT_UART1		45
+#define MXC_INT_UART4		46
+#define MXC_INT_UART5		47
+#define MXC_INT_ECT		48
+#define MXC_INT_SCC_SCM		49
+#define MXC_INT_SCC_SMN		50
+#define MXC_INT_GPIO2		51
+#define MXC_INT_GPIO1		52
+#define MXC_INT_CCM		53
+#define MXC_INT_PCMCIA		54
+#define MXC_INT_WDOG		55
+#define MXC_INT_GPIO3		56
+#define MXC_INT_RESV57		57
+#define MXC_INT_EXT_POWER	58
+#define MXC_INT_EXT_TEMPER	59
+#define MXC_INT_EXT_SENSOR60	60
+#define MXC_INT_EXT_SENSOR61	61
+#define MXC_INT_EXT_WDOG	62
+#define MXC_INT_EXT_TV		63
+
+#define MXC_MAX_INT_LINES	64
+
+#define MXC_GPIO_INT_BASE	MXC_MAX_INT_LINES
+
+/*!
+ * Number of GPIO port as defined in the IC Spec
+ */
+#define GPIO_PORT_NUM		3
+/*!
+ * Number of GPIO pins per port
+ */
+#define GPIO_NUM_PIN		32
+
+#define PROD_SIGNATURE		0x1	/* For MX31 */
+
+#define SYSTEM_REV_MIN		CHIP_REV_1_0
+#define SYSTEM_REV_NUM		3
+
+#endif			/*  __ASM_ARCH_MXC_MX31_H__ */
diff --git a/include/asm-arm/arch-mxc/mxc.h b/include/asm-arm/arch-mxc/mxc.h
new file mode 100644
index 0000000..0837f1f
--- /dev/null
+++ b/include/asm-arm/arch-mxc/mxc.h
@@ -0,0 +1,149 @@
+/*
+ * Copyright 2004-2007 Freescale Semiconductor, Inc. All Rights Reserved.
+ */
+
+/*
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __ASM_ARCH_MXC_H__
+#define __ASM_ARCH_MXC_H__
+
+#ifndef __ASM_ARCH_MXC_HARDWARE_H__
+#error "Do not include directly."
+#endif
+
+/*
+ *****************************************
+ * GPT  Register definitions             *
+ *****************************************
+ */
+#define MXC_GPT_GPTCR		IO_ADDRESS(GPT1_BASE_ADDR + 0x00)
+#define MXC_GPT_GPTPR		IO_ADDRESS(GPT1_BASE_ADDR + 0x04)
+#define MXC_GPT_GPTSR		IO_ADDRESS(GPT1_BASE_ADDR + 0x08)
+#define MXC_GPT_GPTIR		IO_ADDRESS(GPT1_BASE_ADDR + 0x0C)
+#define MXC_GPT_GPTOCR1		IO_ADDRESS(GPT1_BASE_ADDR + 0x10)
+#define MXC_GPT_GPTOCR2		IO_ADDRESS(GPT1_BASE_ADDR + 0x14)
+#define MXC_GPT_GPTOCR3		IO_ADDRESS(GPT1_BASE_ADDR + 0x18)
+#define MXC_GPT_GPTICR1		IO_ADDRESS(GPT1_BASE_ADDR + 0x1C)
+#define MXC_GPT_GPTICR2		IO_ADDRESS(GPT1_BASE_ADDR + 0x20)
+#define MXC_GPT_GPTCNT		IO_ADDRESS(GPT1_BASE_ADDR + 0x24)
+
+/*!
+ * GPT Control register bit definitions
+ */
+#define GPTCR_FO3			(1 << 31)
+#define GPTCR_FO2			(1 << 30)
+#define GPTCR_FO1			(1 << 29)
+
+#define GPTCR_OM3_SHIFT			26
+#define GPTCR_OM3_MASK			(7 << GPTCR_OM3_SHIFT)
+#define GPTCR_OM3_DISCONNECTED		(0 << GPTCR_OM3_SHIFT)
+#define GPTCR_OM3_TOGGLE		(1 << GPTCR_OM3_SHIFT)
+#define GPTCR_OM3_CLEAR			(2 << GPTCR_OM3_SHIFT)
+#define GPTCR_OM3_SET			(3 << GPTCR_OM3_SHIFT)
+#define GPTCR_OM3_GENERATE_LOW		(7 << GPTCR_OM3_SHIFT)
+
+#define GPTCR_OM2_SHIFT			23
+#define GPTCR_OM2_MASK			(7 << GPTCR_OM2_SHIFT)
+#define GPTCR_OM2_DISCONNECTED		(0 << GPTCR_OM2_SHIFT)
+#define GPTCR_OM2_TOGGLE		(1 << GPTCR_OM2_SHIFT)
+#define GPTCR_OM2_CLEAR			(2 << GPTCR_OM2_SHIFT)
+#define GPTCR_OM2_SET			(3 << GPTCR_OM2_SHIFT)
+#define GPTCR_OM2_GENERATE_LOW		(7 << GPTCR_OM2_SHIFT)
+
+#define GPTCR_OM1_SHIFT			20
+#define GPTCR_OM1_MASK			(7 << GPTCR_OM1_SHIFT)
+#define GPTCR_OM1_DISCONNECTED		(0 << GPTCR_OM1_SHIFT)
+#define GPTCR_OM1_TOGGLE		(1 << GPTCR_OM1_SHIFT)
+#define GPTCR_OM1_CLEAR			(2 << GPTCR_OM1_SHIFT)
+#define GPTCR_OM1_SET			(3 << GPTCR_OM1_SHIFT)
+#define GPTCR_OM1_GENERATE_LOW		(7 << GPTCR_OM1_SHIFT)
+
+#define GPTCR_IM2_SHIFT			18
+#define GPTCR_IM2_MASK			(3 << GPTCR_IM2_SHIFT)
+#define GPTCR_IM2_CAPTURE_DISABLE	(0 << GPTCR_IM2_SHIFT)
+#define GPTCR_IM2_CAPTURE_RISING	(1 << GPTCR_IM2_SHIFT)
+#define GPTCR_IM2_CAPTURE_FALLING	(2 << GPTCR_IM2_SHIFT)
+#define GPTCR_IM2_CAPTURE_BOTH		(3 << GPTCR_IM2_SHIFT)
+
+#define GPTCR_IM1_SHIFT			16
+#define GPTCR_IM1_MASK			(3 << GPTCR_IM1_SHIFT)
+#define GPTCR_IM1_CAPTURE_DISABLE	(0 << GPTCR_IM1_SHIFT)
+#define GPTCR_IM1_CAPTURE_RISING	(1 << GPTCR_IM1_SHIFT)
+#define GPTCR_IM1_CAPTURE_FALLING	(2 << GPTCR_IM1_SHIFT)
+#define GPTCR_IM1_CAPTURE_BOTH		(3 << GPTCR_IM1_SHIFT)
+
+#define GPTCR_SWR			(1 << 15)
+#define GPTCR_FRR			(1 << 9)
+
+#define GPTCR_CLKSRC_SHIFT		6
+#define GPTCR_CLKSRC_MASK		(7 << GPTCR_CLKSRC_SHIFT)
+#define GPTCR_CLKSRC_NOCLOCK		(0 << GPTCR_CLKSRC_SHIFT)
+#define GPTCR_CLKSRC_HIGHFREQ		(2 << GPTCR_CLKSRC_SHIFT)
+#define GPTCR_CLKSRC_CLKIN		(3 << GPTCR_CLKSRC_SHIFT)
+#define GPTCR_CLKSRC_CLK32K		(7 << GPTCR_CLKSRC_SHIFT)
+
+#define GPTCR_STOPEN			(1 << 5)
+#define GPTCR_DOZEN			(1 << 4)
+#define GPTCR_WAITEN			(1 << 3)
+#define GPTCR_DBGEN			(1 << 2)
+
+#define GPTCR_ENMOD			(1 << 1)
+#define GPTCR_ENABLE			(1 << 0)
+
+#define GPTSR_OF1			(1 << 0)
+#define GPTSR_OF2			(1 << 1)
+#define GPTSR_OF3			(1 << 2)
+#define GPTSR_IF1			(1 << 3)
+#define GPTSR_IF2			(1 << 4)
+#define GPTSR_ROV			(1 << 5)
+
+#define GPTIR_OF1IE			GPTSR_OF1
+#define GPTIR_OF2IE			GPTSR_OF2
+#define GPTIR_OF3IE			GPTSR_OF3
+#define GPTIR_IF1IE			GPTSR_IF1
+#define GPTIR_IF2IE			GPTSR_IF2
+#define GPTIR_ROVIE			GPTSR_ROV
+
+/*
+ *****************************************
+ * AVIC Registers                        *
+ *****************************************
+ */
+#define AVIC_BASE		IO_ADDRESS(AVIC_BASE_ADDR)
+#define AVIC_INTCNTL		(AVIC_BASE + 0x00)	/* int control reg */
+#define AVIC_NIMASK		(AVIC_BASE + 0x04)	/* int mask reg */
+#define AVIC_INTENNUM		(AVIC_BASE + 0x08)	/* int enable number reg */
+#define AVIC_INTDISNUM		(AVIC_BASE + 0x0C)	/* int disable number reg */
+#define AVIC_INTENABLEH		(AVIC_BASE + 0x10)	/* int enable reg high */
+#define AVIC_INTENABLEL		(AVIC_BASE + 0x14)	/* int enable reg low */
+#define AVIC_INTTYPEH		(AVIC_BASE + 0x18)	/* int type reg high */
+#define AVIC_INTTYPEL		(AVIC_BASE + 0x1C)	/* int type reg low */
+#define AVIC_NIPRIORITY7	(AVIC_BASE + 0x20)	/* norm int priority lvl7 */
+#define AVIC_NIPRIORITY6	(AVIC_BASE + 0x24)	/* norm int priority lvl6 */
+#define AVIC_NIPRIORITY5	(AVIC_BASE + 0x28)	/* norm int priority lvl5 */
+#define AVIC_NIPRIORITY4	(AVIC_BASE + 0x2C)	/* norm int priority lvl4 */
+#define AVIC_NIPRIORITY3	(AVIC_BASE + 0x30)	/* norm int priority lvl3 */
+#define AVIC_NIPRIORITY2	(AVIC_BASE + 0x34)	/* norm int priority lvl2 */
+#define AVIC_NIPRIORITY1	(AVIC_BASE + 0x38)	/* norm int priority lvl1 */
+#define AVIC_NIPRIORITY0	(AVIC_BASE + 0x3C)	/* norm int priority lvl0 */
+#define AVIC_NIVECSR		(AVIC_BASE + 0x40)	/* norm int vector/status */
+#define AVIC_FIVECSR		(AVIC_BASE + 0x44)	/* fast int vector/status */
+#define AVIC_INTSRCH		(AVIC_BASE + 0x48)	/* int source reg high */
+#define AVIC_INTSRCL		(AVIC_BASE + 0x4C)	/* int source reg low */
+#define AVIC_INTFRCH		(AVIC_BASE + 0x50)	/* int force reg high */
+#define AVIC_INTFRCL		(AVIC_BASE + 0x54)	/* int force reg low */
+#define AVIC_NIPNDH		(AVIC_BASE + 0x58)	/* norm int pending high */
+#define AVIC_NIPNDL		(AVIC_BASE + 0x5C)	/* norm int pending low */
+#define AVIC_FIPNDH		(AVIC_BASE + 0x60)	/* fast int pending high */
+#define AVIC_FIPNDL		(AVIC_BASE + 0x64)	/* fast int pending low */
+
+#define SYSTEM_PREV_REG		IO_ADDRESS(IIM_BASE_ADDR + 0x20)
+#define SYSTEM_SREV_REG		IO_ADDRESS(IIM_BASE_ADDR + 0x24)
+#define IIM_PROD_REV_SH		3
+#define IIM_PROD_REV_LEN	5
+
+#endif				/*  __ASM_ARCH_MXC_H__ */
diff --git a/include/asm-arm/arch-mxc/system.h b/include/asm-arm/arch-mxc/system.h
new file mode 100644
index 0000000..109956b
--- /dev/null
+++ b/include/asm-arm/arch-mxc/system.h
@@ -0,0 +1,50 @@
+/*
+ *  Copyright (C) 1999 ARM Limited
+ *  Copyright (C) 2000 Deep Blue Solutions Ltd
+ *  Copyright 2004-2007 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#ifndef __ASM_ARCH_MXC_SYSTEM_H__
+#define __ASM_ARCH_MXC_SYSTEM_H__
+
+/*!
+ * @file system.h
+ * @brief This file contains idle and reset functions.
+ *
+ * @ingroup System
+ */
+
+/*!
+ * This function puts the CPU into idle mode. It is called by default_idle()
+ * in process.c file.
+ */
+static inline void arch_idle(void)
+{
+	cpu_do_idle();
+}
+
+/*
+ * This function resets the system. It is called by machine_restart().
+ *
+ * @param  mode         indicates different kinds of resets
+ */
+static inline void arch_reset(char mode)
+{
+	cpu_reset(0);
+}
+
+#endif				/* __ASM_ARCH_MXC_SYSTEM_H__ */
diff --git a/include/asm-arm/arch-mxc/timex.h b/include/asm-arm/arch-mxc/timex.h
new file mode 100644
index 0000000..59019fa
--- /dev/null
+++ b/include/asm-arm/arch-mxc/timex.h
@@ -0,0 +1,25 @@
+/*
+ *  Copyright (C) 1999 ARM Limited
+ * Copyright 2004-2007 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#ifndef __ASM_ARCH_MXC_TIMEX_H__
+#define __ASM_ARCH_MXC_TIMEX_H__
+
+#include <asm/hardware.h>	/* for CLOCK_TICK_RATE */
+
+#endif				/* __ASM_ARCH_MXC_TIMEX_H__ */
diff --git a/include/asm-arm/arch-mxc/uncompress.h b/include/asm-arm/arch-mxc/uncompress.h
new file mode 100644
index 0000000..ec5787d
--- /dev/null
+++ b/include/asm-arm/arch-mxc/uncompress.h
@@ -0,0 +1,79 @@
+/*
+ *  include/asm-arm/arch-mxc/uncompress.h
+ *
+ *
+ *
+ *  Copyright (C) 1999 ARM Limited
+ *  Copyright (C) Shane Nay (shane@minirl.com)
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+#ifndef __ASM_ARCH_MXC_UNCOMPRESS_H__
+#define __ASM_ARCH_MXC_UNCOMPRESS_H__
+
+#define __MXC_BOOT_UNCOMPRESS
+
+#include <asm/hardware.h>
+#include <asm/processor.h>
+
+#define UART(x) (*(volatile unsigned long *)(serial_port + (x)))
+
+#define USR2 0x98
+#define USR2_TXFE (1<<14)
+#define TXR  0x40
+#define UCR1 0x80
+#define UCR1_UARTEN 1
+
+/*
+ * The following code assumes the serial port has already been
+ * initialized by the bootloader.  We search for the first enabled
+ * port in the most probable order.  If you didn't setup a port in
+ * your bootloader then nothing will appear (which might be desired).
+ *
+ * This does not append a newline
+ */
+
+static void putc(int ch)
+{
+	static unsigned long serial_port = 0;
+
+	if (unlikely(serial_port == 0)) {
+		do {
+			serial_port = UART1_BASE_ADDR;
+			if (UART(UCR1) & UCR1_UARTEN)
+				break;
+			serial_port = UART2_BASE_ADDR;
+			if (UART(UCR1) & UCR1_UARTEN)
+				break;
+			return;
+		} while (0);
+	}
+
+	while (!(UART(USR2) & USR2_TXFE))
+		cpu_relax();
+
+	UART(TXR) = ch;
+}
+
+#define flush() do { } while (0)
+
+/*
+ * nothing to do
+ */
+#define arch_decomp_setup()
+
+#define arch_decomp_wdog()
+
+#endif				/* __ASM_ARCH_MXC_UNCOMPRESS_H__ */
diff --git a/include/asm-arm/arch-mxc/vmalloc.h b/include/asm-arm/arch-mxc/vmalloc.h
new file mode 100644
index 0000000..83a73da
--- /dev/null
+++ b/include/asm-arm/arch-mxc/vmalloc.h
@@ -0,0 +1,36 @@
+/*
+ *  Copyright (C) 2000 Russell King.
+ *  Copyright 2004-2007 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#ifndef __ASM_ARCH_MXC_VMALLOC_H__
+#define __ASM_ARCH_MXC_VMALLOC_H__
+
+/*!
+ * @file vmalloc.h
+ *
+ * @brief This file contains platform specific macros for vmalloc.
+ *
+ * @ingroup System
+ */
+
+/*!
+ * vmalloc ending address
+ */
+#define VMALLOC_END       0xF4000000
+
+#endif				/* __ASM_ARCH_MXC_VMALLOC_H__ */
diff --git a/include/asm-arm/arch-ns9xxx/regs-bbu.h b/include/asm-arm/arch-ns9xxx/regs-bbu.h
index e262695..7ee194d 100644
--- a/include/asm-arm/arch-ns9xxx/regs-bbu.h
+++ b/include/asm-arm/arch-ns9xxx/regs-bbu.h
@@ -15,7 +15,31 @@
 
 /* BBus Utility */
 
-/* GPIO Configuration Register */
-#define BBU_GC(x)	__REG2(0x9060000c, (x))
+/* GPIO Configuration Registers block 1 */
+/* NOTE: the HRM starts counting at 1 for the GPIO registers, here the start is
+ * at 0 for each block.  That is, BBU_GCONFb1(0) is GPIO Configuration Register
+ * #1, BBU_GCONFb2(0) is GPIO Configuration Register #8. */
+#define BBU_GCONFb1(x)	__REG2(0x90600010, (x))
+#define BBU_GCONFb2(x)	__REG2(0x90600100, (x))
+
+#define BBU_GCONFx_DIR(m)	__REGBIT(3 + (((m) & 7) << 2))
+#define BBU_GCONFx_DIR_INPUT(m)	__REGVAL(BBU_GCONFx_DIR(m), 0)
+#define BBU_GCONFx_DIR_OUTPUT(m)	__REGVAL(BBU_GCONFx_DIR(m), 1)
+#define BBU_GCONFx_INV(m)	__REGBIT(2 + (((m) & 7) << 2))
+#define BBU_GCONFx_INV_NO(m)		__REGVAL(BBU_GCONFx_INV(m), 0)
+#define BBU_GCONFx_INV_YES(m)		__REGVAL(BBU_GCONFx_INV(m), 1)
+#define BBU_GCONFx_FUNC(m)	__REGBITS(1 + (((m) & 7) << 2), ((m) & 7) << 2)
+#define BBU_GCONFx_FUNC_0(m)		__REGVAL(BBU_GCONFx_FUNC(m), 0)
+#define BBU_GCONFx_FUNC_1(m)		__REGVAL(BBU_GCONFx_FUNC(m), 1)
+#define BBU_GCONFx_FUNC_2(m)		__REGVAL(BBU_GCONFx_FUNC(m), 2)
+#define BBU_GCONFx_FUNC_3(m)		__REGVAL(BBU_GCONFx_FUNC(m), 3)
+
+#define BBU_GCTRL1	__REG(0x90600030)
+#define BBU_GCTRL2	__REG(0x90600034)
+#define BBU_GCTRL3	__REG(0x90600120)
+
+#define BBU_GSTAT1	__REG(0x90600040)
+#define BBU_GSTAT2	__REG(0x90600044)
+#define BBU_GSTAT3	__REG(0x90600130)
 
 #endif /* ifndef __ASM_ARCH_REGSBBU_H */
diff --git a/include/asm-arm/arch-ns9xxx/regs-mem.h b/include/asm-arm/arch-ns9xxx/regs-mem.h
index 8ed8448..fb455a0 100644
--- a/include/asm-arm/arch-ns9xxx/regs-mem.h
+++ b/include/asm-arm/arch-ns9xxx/regs-mem.h
@@ -79,9 +79,9 @@
 #define MEM_SMC(x)	__REG2(0xa0700200, (x) << 3)
 
 /* Static Memory Configuration Register x: Write protect */
-#define MEM_SMC_WSMC		__REGBIT(20)
-#define MEM_SMC_WSMC_OFF		__REGVAL(MEM_SMC_WSMC, 0)
-#define MEM_SMC_WSMC_ON			__REGVAL(MEM_SMC_WSMC, 1)
+#define MEM_SMC_PSMC		__REGBIT(20)
+#define MEM_SMC_PSMC_OFF		__REGVAL(MEM_SMC_PSMC, 0)
+#define MEM_SMC_PSMC_ON			__REGVAL(MEM_SMC_PSMC, 1)
 
 /* Static Memory Configuration Register x: Buffer enable */
 #define MEM_SMC_BSMC		__REGBIT(19)
diff --git a/include/asm-arm/arch-ns9xxx/regs-sys.h b/include/asm-arm/arch-ns9xxx/regs-sys.h
index a42546a..749262f 100644
--- a/include/asm-arm/arch-ns9xxx/regs-sys.h
+++ b/include/asm-arm/arch-ns9xxx/regs-sys.h
@@ -64,7 +64,7 @@
 
 /* Timer x Control register: Timer enable */
 #define SYS_TCx_TEN		__REGBIT(15)
-#define SYS_TCx_TEN_DIS			__REGVAL(SYS_TCx_TEN, 1)
+#define SYS_TCx_TEN_DIS			__REGVAL(SYS_TCx_TEN, 0)
 #define SYS_TCx_TEN_EN			__REGVAL(SYS_TCx_TEN, 1)
 
 /* Timer x Control register: CPU debug mode */
diff --git a/include/asm-arm/arch-pxa/pm.h b/include/asm-arm/arch-pxa/pm.h
index 52243a6..6903db7 100644
--- a/include/asm-arm/arch-pxa/pm.h
+++ b/include/asm-arm/arch-pxa/pm.h
@@ -7,5 +7,19 @@
  *
  */
 
-extern int pxa_pm_prepare(suspend_state_t state);
+struct pxa_cpu_pm_fns {
+	int	save_size;
+	void	(*save)(unsigned long *);
+	void	(*restore)(unsigned long *);
+	int	(*valid)(suspend_state_t state);
+	void	(*enter)(suspend_state_t state);
+};
+
+extern struct pxa_cpu_pm_fns *pxa_cpu_pm_fns;
+
+/* sleep.S */
+extern void pxa25x_cpu_suspend(unsigned int);
+extern void pxa27x_cpu_suspend(unsigned int);
+extern void pxa_cpu_resume(void);
+
 extern int pxa_pm_enter(suspend_state_t state);
diff --git a/include/asm-arm/arch-s3c2400/map.h b/include/asm-arm/arch-s3c2400/map.h
new file mode 100644
index 0000000..1184d90
--- /dev/null
+++ b/include/asm-arm/arch-s3c2400/map.h
@@ -0,0 +1,66 @@
+/* linux/include/asm-arm/arch-s3c2400/map.h
+ *
+ * Copyright 2003,2007  Simtec Electronics
+ *	http://armlinux.simtec.co.uk/
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * Copyright 2003, Lucas Correia Villa Real
+ *
+ * S3C2400 - Memory map definitions
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#define S3C2400_PA_MEMCTRL	(0x14000000)
+#define S3C2400_PA_USBHOST	(0x14200000)
+#define S3C2400_PA_IRQ		(0x14400000)
+#define S3C2400_PA_DMA		(0x14600000)
+#define S3C2400_PA_CLKPWR	(0x14800000)
+#define S3C2400_PA_LCD		(0x14A00000)
+#define S3C2400_PA_UART		(0x15000000)
+#define S3C2400_PA_TIMER	(0x15100000)
+#define S3C2400_PA_USBDEV	(0x15200140)
+#define S3C2400_PA_WATCHDOG	(0x15300000)
+#define S3C2400_PA_IIC		(0x15400000)
+#define S3C2400_PA_IIS		(0x15508000)
+#define S3C2400_PA_GPIO		(0x15600000)
+#define S3C2400_PA_RTC		(0x15700040)
+#define S3C2400_PA_ADC		(0x15800000)
+#define S3C2400_PA_SPI		(0x15900000)
+
+#define S3C2400_PA_MMC		(0x15A00000)
+#define S3C2400_SZ_MMC		SZ_1M
+
+/* physical addresses of all the chip-select areas */
+
+#define S3C2400_CS0	(0x00000000)
+#define S3C2400_CS1	(0x02000000)
+#define S3C2400_CS2	(0x04000000)
+#define S3C2400_CS3	(0x06000000)
+#define S3C2400_CS4	(0x08000000)
+#define S3C2400_CS5	(0x0A000000)
+#define S3C2400_CS6	(0x0C000000)
+#define S3C2400_CS7	(0x0E000000)
+
+#define S3C2400_SDRAM_PA    (S3C2400_CS6)
+
+/* Use a single interface for common resources between S3C24XX cpus */
+
+#define S3C24XX_PA_IRQ		S3C2400_PA_IRQ
+#define S3C24XX_PA_MEMCTRL	S3C2400_PA_MEMCTRL
+#define S3C24XX_PA_USBHOST	S3C2400_PA_USBHOST
+#define S3C24XX_PA_DMA		S3C2400_PA_DMA
+#define S3C24XX_PA_CLKPWR	S3C2400_PA_CLKPWR
+#define S3C24XX_PA_LCD		S3C2400_PA_LCD
+#define S3C24XX_PA_UART		S3C2400_PA_UART
+#define S3C24XX_PA_TIMER	S3C2400_PA_TIMER
+#define S3C24XX_PA_USBDEV	S3C2400_PA_USBDEV
+#define S3C24XX_PA_WATCHDOG	S3C2400_PA_WATCHDOG
+#define S3C24XX_PA_IIC		S3C2400_PA_IIC
+#define S3C24XX_PA_IIS		S3C2400_PA_IIS
+#define S3C24XX_PA_GPIO		S3C2400_PA_GPIO
+#define S3C24XX_PA_RTC		S3C2400_PA_RTC
+#define S3C24XX_PA_ADC		S3C2400_PA_ADC
+#define S3C24XX_PA_SPI		S3C2400_PA_SPI
diff --git a/include/asm-arm/arch-s3c2400/memory.h b/include/asm-arm/arch-s3c2400/memory.h
new file mode 100644
index 0000000..fb0381d
--- /dev/null
+++ b/include/asm-arm/arch-s3c2400/memory.h
@@ -0,0 +1,23 @@
+/* linux/include/asm-arm/arch-s3c2400/memory.h
+ *  from linux/include/asm-arm/arch-rpc/memory.h
+ *
+ *  Copyright 2007 Simtec Electronics
+ *	http://armlinux.simtec.co.uk/
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ *  Copyright (C) 1996,1997,1998 Russell King.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __ASM_ARCH_MEMORY_H
+#define __ASM_ARCH_MEMORY_H
+
+#define PHYS_OFFSET	UL(0x0C000000)
+
+#define __virt_to_bus(x) __virt_to_phys(x)
+#define __bus_to_virt(x) __phys_to_virt(x)
+
+#endif
diff --git a/include/asm-arm/arch-s3c2410/debug-macro.S b/include/asm-arm/arch-s3c2410/debug-macro.S
index 9306486..9c8cd9a 100644
--- a/include/asm-arm/arch-s3c2410/debug-macro.S
+++ b/include/asm-arm/arch-s3c2410/debug-macro.S
@@ -13,32 +13,23 @@
 */
 
 #include <asm/arch/map.h>
-#include <asm/arch/regs-serial.h>
 #include <asm/arch/regs-gpio.h>
+#include <asm/plat-s3c/regs-serial.h>
 
 #define S3C2410_UART1_OFF (0x4000)
 #define SHIFT_2440TXF (14-9)
 
-		.macro addruart, rx
+	.macro addruart, rx
 		mrc	p15, 0, \rx, c1, c0
 		tst	\rx, #1
 		ldreq	\rx, = S3C24XX_PA_UART
 		ldrne	\rx, = S3C24XX_VA_UART
-#if CONFIG_DEBUG_S3C2410_UART != 0
-		add	\rx, \rx, #(S3C2410_UART1_OFF * CONFIG_DEBUG_S3C2410_UART)
+#if CONFIG_DEBUG_S3C_UART != 0
+		add	\rx, \rx, #(S3C2410_UART1_OFF * CONFIG_DEBUG_S3C_UART)
 #endif
-		.endm
+	.endm
 
-		.macro	senduart,rd,rx
-		strb 	\rd, [\rx, # S3C2410_UTXH ]
-		.endm
-
-		.macro	busyuart, rd, rx
-		ldr	\rd, [ \rx, # S3C2410_UFCON ]
-		tst	\rd, #S3C2410_UFCON_FIFOMODE	@ fifo enabled?
-		beq	1001f				@
-		@ FIFO enabled...
-1003:
+	.macro fifo_full_s3c24xx rd, rx
 		@ check for arm920 vs arm926. currently assume all arm926
 		@ devices have an 64 byte FIFO identical to the s3c2440
 		mrc	p15, 0, \rd, c0, c0
@@ -57,25 +48,22 @@
 		ldr	\rd, [ \rx, # S3C2410_UFSTAT ]
 		moveq	\rd, \rd, lsr #SHIFT_2440TXF
 		tst	\rd, #S3C2410_UFSTAT_TXFULL
-		bne	1003b
-		b	1002f
+	.endm
 
-1001:
-		@ busy waiting for non fifo
-		ldr	\rd, [ \rx, # S3C2410_UTRSTAT ]
-		tst	\rd, #S3C2410_UTRSTAT_TXFE
-		beq	1001b
+	.macro  fifo_full_s3c2410 rd, rx
+		ldr	\rd, [ \rx, # S3C2410_UFSTAT ]
+		tst	\rd, #S3C2410_UFSTAT_TXFULL
+	.endm
 
-1002:		@ exit busyuart
-		.endm
+/* fifo level reading */
 
-		.macro	waituart,rd,rx
-
-		ldr	\rd, [ \rx, # S3C2410_UFCON ]
-		tst	\rd, #S3C2410_UFCON_FIFOMODE	@ fifo enabled?
-		beq	1001f				@
-		@ FIFO enabled...
-1003:
+	.macro fifo_level_s3c24xx rd, rx
+		@ check for arm920 vs arm926. currently assume all arm926
+		@ devices have an 64 byte FIFO identical to the s3c2440
+		mrc	p15, 0, \rd, c0, c0
+		and	\rd, \rd, #0xff0
+		teq	\rd, #0x260
+		beq	10000f
 		mrc	p15, 0, \rd, c1, c0
 		tst	\rd, #1
 		addeq	\rd, \rx, #(S3C24XX_PA_GPIO - S3C24XX_PA_UART)
@@ -85,18 +73,32 @@
 		and	\rd, \rd, #0x00ff0000
 		teq	\rd, #0x00440000		@ is it 2440?
 
+10000:
 		ldr	\rd, [ \rx, # S3C2410_UFSTAT ]
 		andne	\rd, \rd, #S3C2410_UFSTAT_TXMASK
 		andeq	\rd, \rd, #S3C2440_UFSTAT_TXMASK
-		teq	\rd, #0
-		bne	1003b
-		b	1002f
+	.endm
 
-1001:
-		@ idle waiting for non fifo
-		ldr	\rd, [ \rx, # S3C2410_UTRSTAT ]
-		tst	\rd, #S3C2410_UTRSTAT_TXFE
-		beq	1001b
+	.macro fifo_level_s3c2410 rd, rx
+		ldr	\rd, [ \rx, # S3C2410_UFSTAT ]
+		and	\rd, \rd, #S3C2410_UFSTAT_TXMASK
+	.endm
 
-1002:		@ exit busyuart
-		.endm
+/* Select the correct implementation depending on the configuration. The
+ * S3C2440 will get selected by default, as these are the most widely
+ * used variants of these
+*/
+
+#if defined(CONFIG_CPU_LLSERIAL_S3C2410_ONLY)
+#define fifo_full  fifo_full_s3c2410
+#define fifo_level fifo_level_s3c2410
+#warning 2410only
+#elif !defined(CONFIG_CPU_LLSERIAL_S3C2440_ONLY)
+#define fifo_full  fifo_full_s3c24xx
+#define fifo_level fifo_level_s3c24xx
+#warning generic
+#endif
+
+/* include the reset of the code which will do the work */
+
+#include <asm/plat-s3c/debug-macro.S>
diff --git a/include/asm-arm/arch-s3c2410/map.h b/include/asm-arm/arch-s3c2410/map.h
index 19e77f0..b33ed3b 100644
--- a/include/asm-arm/arch-s3c2410/map.h
+++ b/include/asm-arm/arch-s3c2410/map.h
@@ -13,58 +13,36 @@
 #ifndef __ASM_ARCH_MAP_H
 #define __ASM_ARCH_MAP_H
 
-/* we have a bit of a tight squeeze to fit all our registers from
- * 0xF00000000 upwards, since we use all of the nGCS space in some
- * capacity, and also need to fit the S3C2410 registers in as well...
- *
- * we try to ensure stuff like the IRQ registers are available for
- * an single MOVS instruction (ie, only 8 bits of set data)
- *
- * Note, we are trying to remove some of these from the implementation
- * as they are only useful to certain drivers...
- */
+#include <asm/plat-s3c/map.h>
 
-#ifndef __ASSEMBLY__
-#define S3C2410_ADDR(x)	  ((void __iomem __force *)0xF0000000 + (x))
-#else
-#define S3C2410_ADDR(x)	  (0xF0000000 + (x))
-#endif
-
-#define S3C2400_ADDR(x)	  S3C2410_ADDR(x)
+#define S3C2410_ADDR(x)		S3C_ADDR(x)
 
 /* interrupt controller is the first thing we put in, to make
  * the assembly code for the irq detection easier
  */
-#define S3C24XX_VA_IRQ	   S3C2410_ADDR(0x00000000)
-#define S3C2400_PA_IRQ	   (0x14400000)
+#define S3C24XX_VA_IRQ	   S3C_VA_IRQ
 #define S3C2410_PA_IRQ	   (0x4A000000)
 #define S3C24XX_SZ_IRQ	   SZ_1M
 
 /* memory controller registers */
-#define S3C24XX_VA_MEMCTRL S3C2410_ADDR(0x00100000)
-#define S3C2400_PA_MEMCTRL (0x14000000)
+#define S3C24XX_VA_MEMCTRL S3C_VA_MEM
 #define S3C2410_PA_MEMCTRL (0x48000000)
 #define S3C24XX_SZ_MEMCTRL SZ_1M
 
 /* USB host controller */
-#define S3C2400_PA_USBHOST (0x14200000)
 #define S3C2410_PA_USBHOST (0x49000000)
 #define S3C24XX_SZ_USBHOST SZ_1M
 
 /* DMA controller */
-#define S3C2400_PA_DMA	   (0x14600000)
 #define S3C2410_PA_DMA	   (0x4B000000)
 #define S3C24XX_SZ_DMA	   SZ_1M
 
 /* Clock and Power management */
-#define S3C24XX_VA_CLKPWR  S3C2410_ADDR(0x00200000)
-#define S3C2400_PA_CLKPWR  (0x14800000)
+#define S3C24XX_VA_CLKPWR  S3C_VA_SYS
 #define S3C2410_PA_CLKPWR  (0x4C000000)
 #define S3C24XX_SZ_CLKPWR  SZ_1M
 
 /* LCD controller */
-#define S3C24XX_VA_LCD	   S3C2410_ADDR(0x00300000)
-#define S3C2400_PA_LCD	   (0x14A00000)
 #define S3C2410_PA_LCD	   (0x4D000000)
 #define S3C24XX_SZ_LCD	   SZ_1M
 
@@ -72,41 +50,30 @@
 #define S3C2410_PA_NAND	   (0x4E000000)
 #define S3C24XX_SZ_NAND	   SZ_1M
 
-/* MMC controller - available on the S3C2400 */
-#define S3C2400_PA_MMC 	   (0x15A00000)
-#define S3C2400_SZ_MMC 	   SZ_1M
-
 /* UARTs */
-#define S3C24XX_VA_UART	   S3C2410_ADDR(0x00400000)
-#define S3C2400_PA_UART	   (0x15000000)
+#define S3C24XX_VA_UART	   S3C_VA_UART
 #define S3C2410_PA_UART	   (0x50000000)
 #define S3C24XX_SZ_UART	   SZ_1M
 
 /* Timers */
-#define S3C24XX_VA_TIMER   S3C2410_ADDR(0x00500000)
-#define S3C2400_PA_TIMER   (0x15100000)
+#define S3C24XX_VA_TIMER   S3C_VA_TIMER
 #define S3C2410_PA_TIMER   (0x51000000)
 #define S3C24XX_SZ_TIMER   SZ_1M
 
 /* USB Device port */
-#define S3C24XX_VA_USBDEV  S3C2410_ADDR(0x00600000)
-#define S3C2400_PA_USBDEV  (0x15200140)
 #define S3C2410_PA_USBDEV  (0x52000000)
 #define S3C24XX_SZ_USBDEV  SZ_1M
 
 /* Watchdog */
-#define S3C24XX_VA_WATCHDOG S3C2410_ADDR(0x00700000)
-#define S3C2400_PA_WATCHDOG (0x15300000)
+#define S3C24XX_VA_WATCHDOG S3C_VA_WATCHDOG
 #define S3C2410_PA_WATCHDOG (0x53000000)
 #define S3C24XX_SZ_WATCHDOG SZ_1M
 
 /* IIC hardware controller */
-#define S3C2400_PA_IIC	   (0x15400000)
 #define S3C2410_PA_IIC	   (0x54000000)
 #define S3C24XX_SZ_IIC	   SZ_1M
 
 /* IIS controller */
-#define S3C2400_PA_IIS	   (0x15508000)
 #define S3C2410_PA_IIS	   (0x55000000)
 #define S3C24XX_SZ_IIS	   SZ_1M
 
@@ -116,27 +83,23 @@
  * it is the same distance apart from the UART in the
  * phsyical address space, as the initial mapping for the IO
  * is done as a 1:1 maping. This puts it (currently) at
- * 0xF6800000, which is not in the way of any current mapping
+ * 0xFA800000, which is not in the way of any current mapping
  * by the base system.
 */
 
-#define S3C2400_PA_GPIO	   (0x15600000)
 #define S3C2410_PA_GPIO	   (0x56000000)
 #define S3C24XX_VA_GPIO	   ((S3C2410_PA_GPIO - S3C24XX_PA_UART) + S3C24XX_VA_UART)
 #define S3C24XX_SZ_GPIO	   SZ_1M
 
 /* RTC */
-#define S3C2400_PA_RTC	   (0x15700040)
 #define S3C2410_PA_RTC	   (0x57000000)
 #define S3C24XX_SZ_RTC	   SZ_1M
 
 /* ADC */
-#define S3C2400_PA_ADC	   (0x15800000)
 #define S3C2410_PA_ADC	   (0x58000000)
 #define S3C24XX_SZ_ADC	   SZ_1M
 
 /* SPI */
-#define S3C2400_PA_SPI	   (0x15900000)
 #define S3C2410_PA_SPI	   (0x59000000)
 #define S3C24XX_SZ_SPI	   SZ_1M
 
@@ -177,37 +140,8 @@
 
 #define S3C2410_SDRAM_PA    (S3C2410_CS6)
 
-#define S3C2400_CS0 (0x00000000)
-#define S3C2400_CS1 (0x02000000)
-#define S3C2400_CS2 (0x04000000)
-#define S3C2400_CS3 (0x06000000)
-#define S3C2400_CS4 (0x08000000)
-#define S3C2400_CS5 (0x0A000000)
-#define S3C2400_CS6 (0x0C000000)
-#define S3C2400_CS7 (0x0E000000)
-
-#define S3C2400_SDRAM_PA    (S3C2400_CS6)
-
 /* Use a single interface for common resources between S3C24XX cpus */
 
-#ifdef CONFIG_CPU_S3C2400
-#define S3C24XX_PA_IRQ      S3C2400_PA_IRQ
-#define S3C24XX_PA_MEMCTRL  S3C2400_PA_MEMCTRL
-#define S3C24XX_PA_USBHOST  S3C2400_PA_USBHOST
-#define S3C24XX_PA_DMA      S3C2400_PA_DMA
-#define S3C24XX_PA_CLKPWR   S3C2400_PA_CLKPWR
-#define S3C24XX_PA_LCD      S3C2400_PA_LCD
-#define S3C24XX_PA_UART     S3C2400_PA_UART
-#define S3C24XX_PA_TIMER    S3C2400_PA_TIMER
-#define S3C24XX_PA_USBDEV   S3C2400_PA_USBDEV
-#define S3C24XX_PA_WATCHDOG S3C2400_PA_WATCHDOG
-#define S3C24XX_PA_IIC      S3C2400_PA_IIC
-#define S3C24XX_PA_IIS      S3C2400_PA_IIS
-#define S3C24XX_PA_GPIO     S3C2400_PA_GPIO
-#define S3C24XX_PA_RTC      S3C2400_PA_RTC
-#define S3C24XX_PA_ADC      S3C2400_PA_ADC
-#define S3C24XX_PA_SPI      S3C2400_PA_SPI
-#else
 #define S3C24XX_PA_IRQ      S3C2410_PA_IRQ
 #define S3C24XX_PA_MEMCTRL  S3C2410_PA_MEMCTRL
 #define S3C24XX_PA_USBHOST  S3C2410_PA_USBHOST
@@ -224,7 +158,6 @@
 #define S3C24XX_PA_RTC      S3C2410_PA_RTC
 #define S3C24XX_PA_ADC      S3C2410_PA_ADC
 #define S3C24XX_PA_SPI      S3C2410_PA_SPI
-#endif
 
 /* deal with the registers that move under the 2412/2413 */
 
diff --git a/include/asm-arm/arch-s3c2410/memory.h b/include/asm-arm/arch-s3c2410/memory.h
index 4be6a74..533e243 100644
--- a/include/asm-arm/arch-s3c2410/memory.h
+++ b/include/asm-arm/arch-s3c2410/memory.h
@@ -11,20 +11,7 @@
 #ifndef __ASM_ARCH_MEMORY_H
 #define __ASM_ARCH_MEMORY_H
 
-/*
- * DRAM starts at 0x30000000 for S3C2410/S3C2440
- * and at 0x0C000000 for S3C2400
- */
-#ifdef CONFIG_CPU_S3C2400
-#define PHYS_OFFSET	UL(0x0C000000)
-#else
 #define PHYS_OFFSET	UL(0x30000000)
-#endif
-
-/*
- * These are exactly the same on the S3C2410 as the
- * physical memory view.
-*/
 
 #define __virt_to_bus(x) __virt_to_phys(x)
 #define __bus_to_virt(x) __phys_to_virt(x)
diff --git a/include/asm-arm/arch-s3c2410/regs-lcd.h b/include/asm-arm/arch-s3c2410/regs-lcd.h
index b7faeb0..76fe5f6 100644
--- a/include/asm-arm/arch-s3c2410/regs-lcd.h
+++ b/include/asm-arm/arch-s3c2410/regs-lcd.h
@@ -12,7 +12,7 @@
 #ifndef ___ASM_ARCH_REGS_LCD_H
 #define ___ASM_ARCH_REGS_LCD_H "$Id: lcd.h,v 1.3 2003/06/26 13:25:06 ben Exp $"
 
-#define S3C2410_LCDREG(x) ((x) + S3C24XX_VA_LCD)
+#define S3C2410_LCDREG(x)	(x)
 
 /* LCD control registers */
 #define S3C2410_LCDCON1	    S3C2410_LCDREG(0x00)
diff --git a/include/asm-arm/arch-s3c2410/system.h b/include/asm-arm/arch-s3c2410/system.h
index 1c74ef1..6389178 100644
--- a/include/asm-arm/arch-s3c2410/system.h
+++ b/include/asm-arm/arch-s3c2410/system.h
@@ -17,7 +17,7 @@
 #include <asm/arch/idle.h>
 #include <asm/arch/reset.h>
 
-#include <asm/arch/regs-watchdog.h>
+#include <asm/plat-s3c/regs-watchdog.h>
 #include <asm/arch/regs-clock.h>
 
 void (*s3c24xx_idle)(void);
diff --git a/include/asm-arm/arch-s3c2410/uncompress.h b/include/asm-arm/arch-s3c2410/uncompress.h
index dcb2cef..48a5731 100644
--- a/include/asm-arm/arch-s3c2410/uncompress.h
+++ b/include/asm-arm/arch-s3c2410/uncompress.h
@@ -1,6 +1,7 @@
 /* linux/include/asm-arm/arch-s3c2410/uncompress.h
  *
- * Copyright (c) 2003 Simtec Electronics
+ * Copyright (c) 2003, 2007 Simtec Electronics
+ *	http://armlinux.simtec.co.uk/
  *	Ben Dooks <ben@simtec.co.uk>
  *
  * S3C2410 - uncompress code
@@ -13,153 +14,39 @@
 #ifndef __ASM_ARCH_UNCOMPRESS_H
 #define __ASM_ARCH_UNCOMPRESS_H
 
-typedef unsigned int upf_t;	/* cannot include linux/serial_core.h */
-
-/* defines for UART registers */
-#include "asm/arch/regs-serial.h"
-#include "asm/arch/regs-gpio.h"
-#include "asm/arch/regs-watchdog.h"
-
+#include <asm/arch/regs-gpio.h>
 #include <asm/arch/map.h>
 
 /* working in physical space... */
 #undef S3C2410_GPIOREG
-#undef S3C2410_WDOGREG
-
 #define S3C2410_GPIOREG(x) ((S3C24XX_PA_GPIO + (x)))
-#define S3C2410_WDOGREG(x) ((S3C24XX_PA_WATCHDOG + (x)))
 
-/* how many bytes we allow into the FIFO at a time in FIFO mode */
-#define FIFO_MAX	 (14)
+#include <asm/plat-s3c/uncompress.h>
 
-#define uart_base S3C24XX_PA_UART + (0x4000*CONFIG_S3C2410_LOWLEVEL_UART_PORT)
-
-static __inline__ void
-uart_wr(unsigned int reg, unsigned int val)
+static inline int is_arm926(void)
 {
-	volatile unsigned int *ptr;
+	unsigned int cpuid;
 
-	ptr = (volatile unsigned int *)(reg + uart_base);
-	*ptr = val;
+	asm volatile ("mrc p15, 0, %0, c1, c0, 0" : "=r" (cpuid));
+
+	return ((cpuid & 0xff0) == 0x260);
 }
 
-static __inline__ unsigned int
-uart_rd(unsigned int reg)
+static void arch_detect_cpu(void)
 {
-	volatile unsigned int *ptr;
+	unsigned int cpuid;
 
-	ptr = (volatile unsigned int *)(reg + uart_base);
-	return *ptr;
-}
-
-
-/* we can deal with the case the UARTs are being run
- * in FIFO mode, so that we don't hold up our execution
- * waiting for tx to happen...
-*/
-
-static void putc(int ch)
-{
-	int cpuid = S3C2410_GSTATUS1_2410;
-
-#ifndef CONFIG_CPU_S3C2400
 	cpuid = *((volatile unsigned int *)S3C2410_GSTATUS1);
 	cpuid &= S3C2410_GSTATUS1_IDMASK;
-#endif
 
-	if (uart_rd(S3C2410_UFCON) & S3C2410_UFCON_FIFOMODE) {
-		int level;
-
-		while (1) {
-			level = uart_rd(S3C2410_UFSTAT);
-
-			if (cpuid == S3C2410_GSTATUS1_2440 ||
-			    cpuid == S3C2410_GSTATUS1_2442) {
-				level &= S3C2440_UFSTAT_TXMASK;
-				level >>= S3C2440_UFSTAT_TXSHIFT;
-			} else {
-				level &= S3C2410_UFSTAT_TXMASK;
-				level >>= S3C2410_UFSTAT_TXSHIFT;
-			}
-
-			if (level < FIFO_MAX)
-				break;
-		}
-
+	if (is_arm926() || cpuid == S3C2410_GSTATUS1_2440 ||
+	    cpuid == S3C2410_GSTATUS1_2442) {
+		fifo_mask = S3C2440_UFSTAT_TXMASK;
+		fifo_max = 63 << S3C2440_UFSTAT_TXSHIFT;
 	} else {
-		/* not using fifos */
-
-		while ((uart_rd(S3C2410_UTRSTAT) & S3C2410_UTRSTAT_TXE) != S3C2410_UTRSTAT_TXE)
-			barrier();
+		fifo_mask = S3C2410_UFSTAT_TXMASK;
+		fifo_max = 15 << S3C2410_UFSTAT_TXSHIFT;
 	}
-
-	/* write byte to transmission register */
-	uart_wr(S3C2410_UTXH, ch);
 }
 
-static inline void flush(void)
-{
-}
-
-#define __raw_writel(d,ad) do { *((volatile unsigned int *)(ad)) = (d); } while(0)
-
-/* CONFIG_S3C2410_BOOT_WATCHDOG
- *
- * Simple boot-time watchdog setup, to reboot the system if there is
- * any problem with the boot process
-*/
-
-#ifdef CONFIG_S3C2410_BOOT_WATCHDOG
-
-#define WDOG_COUNT (0xff00)
-
-static inline void arch_decomp_wdog(void)
-{
-	__raw_writel(WDOG_COUNT, S3C2410_WTCNT);
-}
-
-static void arch_decomp_wdog_start(void)
-{
-	__raw_writel(WDOG_COUNT, S3C2410_WTDAT);
-	__raw_writel(WDOG_COUNT, S3C2410_WTCNT);
-	__raw_writel(S3C2410_WTCON_ENABLE | S3C2410_WTCON_DIV128 | S3C2410_WTCON_RSTEN | S3C2410_WTCON_PRESCALE(0x80), S3C2410_WTCON);
-}
-
-#else
-#define arch_decomp_wdog_start()
-#define arch_decomp_wdog()
-#endif
-
-#ifdef CONFIG_S3C2410_BOOT_ERROR_RESET
-
-static void arch_decomp_error(const char *x)
-{
-	putstr("\n\n");
-	putstr(x);
-	putstr("\n\n -- System resetting\n");
-
-	__raw_writel(0x4000, S3C2410_WTDAT);
-	__raw_writel(0x4000, S3C2410_WTCNT);
-	__raw_writel(S3C2410_WTCON_ENABLE | S3C2410_WTCON_DIV128 | S3C2410_WTCON_RSTEN | S3C2410_WTCON_PRESCALE(0x40), S3C2410_WTCON);
-
-	while(1);
-}
-
-#define arch_error arch_decomp_error
-#endif
-
-static void error(char *err);
-
-static void
-arch_decomp_setup(void)
-{
-	/* we may need to setup the uart(s) here if we are not running
-	 * on an BAST... the BAST will have left the uarts configured
-	 * after calling linux.
-	 */
-
-	arch_decomp_wdog_start();
-}
-
-
 #endif /* __ASM_ARCH_UNCOMPRESS_H */
diff --git a/include/asm-arm/arch-sa1100/jornada720.h b/include/asm-arm/arch-sa1100/jornada720.h
new file mode 100644
index 0000000..45d2bb5
--- /dev/null
+++ b/include/asm-arm/arch-sa1100/jornada720.h
@@ -0,0 +1,27 @@
+/*
+ * include/asm-arm/arch-sa1100/jornada720.h
+ *
+ * This file contains SSP/MCU communication definitions for HP Jornada 710/720/728
+ *
+ * Copyright (C) 2007 Kristoffer Ericson <Kristoffer.Ericson@gmail.com>
+ *  Copyright (C) 2000 John Ankcorn <jca@lcs.mit.edu>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+ /* HP Jornada 7xx microprocessor commands */
+#define GETBATTERYDATA		0xc0
+#define GETSCANKEYCODE		0x90
+#define GETTOUCHSAMPLES		0xa0
+#define GETCONTRAST		0xD0
+#define SETCONTRAST		0xD1
+#define GETBRIGHTNESS		0xD2
+#define SETBRIGHTNESS		0xD3
+#define CONTRASTOFF		0xD8
+#define BRIGHTNESSOFF		0xD9
+#define PWMOFF			0xDF
+#define TXDUMMY			0x11
+#define ERRORCODE		0x00
diff --git a/include/asm-arm/elf.h b/include/asm-arm/elf.h
index d7a777f..ec1c685 100644
--- a/include/asm-arm/elf.h
+++ b/include/asm-arm/elf.h
@@ -1,13 +1,14 @@
 #ifndef __ASMARM_ELF_H
 #define __ASMARM_ELF_H
 
+#include <asm/hwcap.h>
+
 #ifndef __ASSEMBLY__
 /*
  * ELF register definitions..
  */
 #include <asm/ptrace.h>
 #include <asm/user.h>
-#include <asm/hwcap.h>
 
 typedef unsigned long elf_greg_t;
 typedef unsigned long elf_freg_t[3];
diff --git a/include/asm-arm/floppy.h b/include/asm-arm/floppy.h
index 54b5ae4..d595c15 100644
--- a/include/asm-arm/floppy.h
+++ b/include/asm-arm/floppy.h
@@ -30,15 +30,21 @@
 #define fd_disable_irq()	disable_irq(IRQ_FLOPPYDISK)
 #define fd_enable_irq()		enable_irq(IRQ_FLOPPYDISK)
 
+static inline int fd_dma_setup(void *data, unsigned int length,
+			       unsigned int mode, unsigned long addr)
+{
+	set_dma_mode(DMA_FLOPPY, mode);
+	__set_dma_addr(DMA_FLOPPY, data);
+	set_dma_count(DMA_FLOPPY, length);
+	virtual_dma_port = addr;
+	enable_dma(DMA_FLOPPY);
+	return 0;
+}
+#define fd_dma_setup		fd_dma_setup
+
 #define fd_request_dma()	request_dma(DMA_FLOPPY,"floppy")
 #define fd_free_dma()		free_dma(DMA_FLOPPY)
 #define fd_disable_dma()	disable_dma(DMA_FLOPPY)
-#define fd_enable_dma()		enable_dma(DMA_FLOPPY)
-#define fd_clear_dma_ff()	clear_dma_ff(DMA_FLOPPY)
-#define fd_set_dma_mode(mode)	set_dma_mode(DMA_FLOPPY, (mode))
-#define fd_set_dma_addr(addr)	set_dma_addr(DMA_FLOPPY, virt_to_bus((addr)))
-#define fd_set_dma_count(len)	set_dma_count(DMA_FLOPPY, (len))
-#define fd_cacheflush(addr,sz)
 
 /* need to clean up dma.h */
 #define DMA_FLOPPYDISK		DMA_FLOPPY
diff --git a/include/asm-arm/pgtable-nommu.h b/include/asm-arm/pgtable-nommu.h
index 0c8be19..b186bc8 100644
--- a/include/asm-arm/pgtable-nommu.h
+++ b/include/asm-arm/pgtable-nommu.h
@@ -102,7 +102,8 @@
 #define v4_tlb_fns	(0)
 #define v4wb_tlb_fns	(0)
 #define v4wbi_tlb_fns	(0)
-#define v6_tlb_fns	(0)
+#define v6wbi_tlb_fns	(0)
+#define v7wbi_tlb_fns	(0)
 
 #define v3_user_fns	(0)
 #define v4_user_fns	(0)
diff --git a/include/asm-arm/plat-s3c/debug-macro.S b/include/asm-arm/plat-s3c/debug-macro.S
new file mode 100644
index 0000000..84c40b8
--- /dev/null
+++ b/include/asm-arm/plat-s3c/debug-macro.S
@@ -0,0 +1,75 @@
+/* linux/include/asm-arm/plat-s3c/debug-macro.S
+ *
+ * Copyright 2005, 2007 Simtec Electronics
+ *	http://armlinux.simtec.co.uk/
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <asm/plat-s3c/regs-serial.h>
+
+/* The S3C2440 implementations are used by default as they are the
+ * most widely re-used */
+
+	.macro fifo_level_s3c2440 rd, rx
+		ldr	\rd, [ \rx, # S3C2410_UFSTAT ]
+		and	\rd, \rd, #S3C2440_UFSTAT_TXMASK
+	.endm
+
+#ifndef fifo_level
+#define fifo_level fifo_level_s3c2410
+#endif
+
+	.macro  fifo_full_s3c2440 rd, rx
+		ldr	\rd, [ \rx, # S3C2410_UFSTAT ]
+		tst	\rd, #S3C2440_UFSTAT_TXFULL
+	.endm
+
+#ifndef fifo_full
+#define fifo_full fifo_full_s3c2440
+#endif
+
+	.macro	senduart,rd,rx
+		strb 	\rd, [\rx, # S3C2410_UTXH ]
+	.endm
+
+	.macro	busyuart, rd, rx
+		ldr	\rd, [ \rx, # S3C2410_UFCON ]
+		tst	\rd, #S3C2410_UFCON_FIFOMODE	@ fifo enabled?
+		beq	1001f				@
+		@ FIFO enabled...
+1003:
+		fifo_full \rd, \rx
+		bne	1003b
+		b	1002f
+
+1001:
+		@ busy waiting for non fifo
+		ldr	\rd, [ \rx, # S3C2410_UTRSTAT ]
+		tst	\rd, #S3C2410_UTRSTAT_TXFE
+		beq	1001b
+
+1002:		@ exit busyuart
+	.endm
+
+	.macro	waituart,rd,rx
+		ldr	\rd, [ \rx, # S3C2410_UFCON ]
+		tst	\rd, #S3C2410_UFCON_FIFOMODE	@ fifo enabled?
+		beq	1001f				@
+		@ FIFO enabled...
+1003:
+		fifo_level \rd, \rx
+		teq	\rd, #0
+		bne	1003b
+		b	1002f
+1001:
+		@ idle waiting for non fifo
+		ldr	\rd, [ \rx, # S3C2410_UTRSTAT ]
+		tst	\rd, #S3C2410_UTRSTAT_TXFE
+		beq	1001b
+
+1002:		@ exit busyuart
+	.endm
diff --git a/include/asm-arm/arch-s3c2410/iic.h b/include/asm-arm/plat-s3c/iic.h
similarity index 100%
rename from include/asm-arm/arch-s3c2410/iic.h
rename to include/asm-arm/plat-s3c/iic.h
diff --git a/include/asm-arm/plat-s3c/map.h b/include/asm-arm/plat-s3c/map.h
new file mode 100644
index 0000000..95a82b0
--- /dev/null
+++ b/include/asm-arm/plat-s3c/map.h
@@ -0,0 +1,40 @@
+/* linux/include/asm-arm/plat-s3c/map.h
+ *
+ * Copyright 2003, 2007 Simtec Electronics
+ *	http://armlinux.simtec.co.uk/
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C - Memory map definitions (virtual addresses)
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __ASM_PLAT_MAP_H
+#define __ASM_PLAT_MAP_H __FILE__
+
+/* Fit all our registers in at 0xF4000000 upwards, trying to use as
+ * little of the VA space as possible so vmalloc and friends have a
+ * better chance of getting memory.
+ *
+ * we try to ensure stuff like the IRQ registers are available for
+ * an single MOVS instruction (ie, only 8 bits of set data)
+ */
+
+#define S3C_ADDR_BASE	(0xF4000000)
+
+#ifndef __ASSEMBLY__
+#define S3C_ADDR(x)	((void __iomem __force *)S3C_ADDR_BASE + (x))
+#else
+#define S3C_ADDR(x)	(S3C_ADDR_BASE + (x))
+#endif
+
+#define S3C_VA_IRQ	S3C_ADDR(0x000000000)	/* irq controller(s) */
+#define S3C_VA_SYS	S3C_ADDR(0x001000000)	/* system control */
+#define S3C_VA_MEM	S3C_ADDR(0x002000000)	/* system control */
+#define S3C_VA_TIMER	S3C_ADDR(0x003000000)	/* timer block */
+#define S3C_VA_WATCHDOG	S3C_ADDR(0x004000000)	/* watchdog */
+#define S3C_VA_UART	S3C_ADDR(0x010000000)	/* UART */
+
+#endif /* __ASM_PLAT_MAP_H */
diff --git a/include/asm-arm/arch-s3c2410/nand.h b/include/asm-arm/plat-s3c/nand.h
similarity index 100%
rename from include/asm-arm/arch-s3c2410/nand.h
rename to include/asm-arm/plat-s3c/nand.h
diff --git a/include/asm-arm/arch-s3c2410/regs-ac97.h b/include/asm-arm/plat-s3c/regs-ac97.h
similarity index 100%
rename from include/asm-arm/arch-s3c2410/regs-ac97.h
rename to include/asm-arm/plat-s3c/regs-ac97.h
diff --git a/include/asm-arm/arch-s3c2410/regs-adc.h b/include/asm-arm/plat-s3c/regs-adc.h
similarity index 100%
rename from include/asm-arm/arch-s3c2410/regs-adc.h
rename to include/asm-arm/plat-s3c/regs-adc.h
diff --git a/include/asm-arm/arch-s3c2410/regs-iic.h b/include/asm-arm/plat-s3c/regs-iic.h
similarity index 100%
rename from include/asm-arm/arch-s3c2410/regs-iic.h
rename to include/asm-arm/plat-s3c/regs-iic.h
diff --git a/include/asm-arm/arch-s3c2410/regs-nand.h b/include/asm-arm/plat-s3c/regs-nand.h
similarity index 100%
rename from include/asm-arm/arch-s3c2410/regs-nand.h
rename to include/asm-arm/plat-s3c/regs-nand.h
diff --git a/include/asm-arm/arch-s3c2410/regs-rtc.h b/include/asm-arm/plat-s3c/regs-rtc.h
similarity index 100%
rename from include/asm-arm/arch-s3c2410/regs-rtc.h
rename to include/asm-arm/plat-s3c/regs-rtc.h
diff --git a/include/asm-arm/arch-s3c2410/regs-serial.h b/include/asm-arm/plat-s3c/regs-serial.h
similarity index 96%
rename from include/asm-arm/arch-s3c2410/regs-serial.h
rename to include/asm-arm/plat-s3c/regs-serial.h
index 8946702..923e114 100644
--- a/include/asm-arm/arch-s3c2410/regs-serial.h
+++ b/include/asm-arm/plat-s3c/regs-serial.h
@@ -32,10 +32,10 @@
 #ifndef __ASM_ARM_REGS_SERIAL_H
 #define __ASM_ARM_REGS_SERIAL_H
 
-#define S3C24XX_VA_UART0      (S3C24XX_VA_UART)
-#define S3C24XX_VA_UART1      (S3C24XX_VA_UART + 0x4000 )
-#define S3C24XX_VA_UART2      (S3C24XX_VA_UART + 0x8000 )
-#define S3C24XX_VA_UART3      (S3C24XX_VA_UART + 0xC000 )
+#define S3C24XX_VA_UART0      (S3C_VA_UART)
+#define S3C24XX_VA_UART1      (S3C_VA_UART + 0x4000 )
+#define S3C24XX_VA_UART2      (S3C_VA_UART + 0x8000 )
+#define S3C24XX_VA_UART3      (S3C_VA_UART + 0xC000 )
 
 #define S3C2410_PA_UART0      (S3C24XX_PA_UART)
 #define S3C2410_PA_UART1      (S3C24XX_PA_UART + 0x4000 )
diff --git a/include/asm-arm/arch-s3c2410/regs-timer.h b/include/asm-arm/plat-s3c/regs-timer.h
similarity index 86%
rename from include/asm-arm/arch-s3c2410/regs-timer.h
rename to include/asm-arm/plat-s3c/regs-timer.h
index 6f8fe43..8b0d594 100644
--- a/include/asm-arm/arch-s3c2410/regs-timer.h
+++ b/include/asm-arm/plat-s3c/regs-timer.h
@@ -14,12 +14,12 @@
 #ifndef __ASM_ARCH_REGS_TIMER_H
 #define __ASM_ARCH_REGS_TIMER_H "$Id: timer.h,v 1.4 2003/05/06 19:30:50 ben Exp $"
 
-#define S3C2410_TIMERREG(x) (S3C24XX_VA_TIMER + (x))
-#define S3C2410_TIMERREG2(tmr,reg) S3C2410_TIMERREG((reg)+0x0c+((tmr)*0x0c))
+#define S3C_TIMERREG(x) (S3C_VA_TIMER + (x))
+#define S3C_TIMERREG2(tmr,reg) S3C_TIMERREG((reg)+0x0c+((tmr)*0x0c))
 
-#define S3C2410_TCFG0	      S3C2410_TIMERREG(0x00)
-#define S3C2410_TCFG1	      S3C2410_TIMERREG(0x04)
-#define S3C2410_TCON	      S3C2410_TIMERREG(0x08)
+#define S3C2410_TCFG0	      S3C_TIMERREG(0x00)
+#define S3C2410_TCFG1	      S3C_TIMERREG(0x04)
+#define S3C2410_TCON	      S3C_TIMERREG(0x08)
 
 #define S3C2410_TCFG_PRESCALER0_MASK (255<<0)
 #define S3C2410_TCFG_PRESCALER1_MASK (255<<8)
@@ -71,9 +71,9 @@
 
 /* WARNING - timer 4 has no buffer reg, and it's observation is at +4 */
 
-#define S3C2410_TCNTB(tmr)    S3C2410_TIMERREG2(tmr, 0x00)
-#define S3C2410_TCMPB(tmr)    S3C2410_TIMERREG2(tmr, 0x04)
-#define S3C2410_TCNTO(tmr)    S3C2410_TIMERREG2(tmr, (((tmr) == 4) ? 0x04 : 0x08))
+#define S3C2410_TCNTB(tmr)    S3C_TIMERREG2(tmr, 0x00)
+#define S3C2410_TCMPB(tmr)    S3C_TIMERREG2(tmr, 0x04)
+#define S3C2410_TCNTO(tmr)    S3C_TIMERREG2(tmr, (((tmr) == 4) ? 0x04 : 0x08))
 
 #define S3C2410_TCON_T4RELOAD	  (1<<22)
 #define S3C2410_TCON_T4MANUALUPD  (1<<21)
diff --git a/include/asm-arm/arch-s3c2410/regs-watchdog.h b/include/asm-arm/plat-s3c/regs-watchdog.h
similarity index 83%
rename from include/asm-arm/arch-s3c2410/regs-watchdog.h
rename to include/asm-arm/plat-s3c/regs-watchdog.h
index a9c5d49..56c4193b 100644
--- a/include/asm-arm/arch-s3c2410/regs-watchdog.h
+++ b/include/asm-arm/plat-s3c/regs-watchdog.h
@@ -14,11 +14,11 @@
 #ifndef __ASM_ARCH_REGS_WATCHDOG_H
 #define __ASM_ARCH_REGS_WATCHDOG_H "$Id: watchdog.h,v 1.2 2003/04/29 13:31:09 ben Exp $"
 
-#define S3C2410_WDOGREG(x) ((x) + S3C24XX_VA_WATCHDOG)
+#define S3C_WDOGREG(x) ((x) + S3C_VA_WATCHDOG)
 
-#define S3C2410_WTCON	   S3C2410_WDOGREG(0x00)
-#define S3C2410_WTDAT	   S3C2410_WDOGREG(0x04)
-#define S3C2410_WTCNT	   S3C2410_WDOGREG(0x08)
+#define S3C2410_WTCON	   S3C_WDOGREG(0x00)
+#define S3C2410_WTDAT	   S3C_WDOGREG(0x04)
+#define S3C2410_WTCNT	   S3C_WDOGREG(0x08)
 
 /* the watchdog can either generate a reset pulse, or an
  * interrupt.
diff --git a/include/asm-arm/plat-s3c/uncompress.h b/include/asm-arm/plat-s3c/uncompress.h
new file mode 100644
index 0000000..b5e6208
--- /dev/null
+++ b/include/asm-arm/plat-s3c/uncompress.h
@@ -0,0 +1,155 @@
+/* linux/include/asm-arm/plat-s3c/uncompress.h
+ *
+ * Copyright 2003, 2007 Simtec Electronics
+ *	http://armlinux.simtec.co.uk/
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C - uncompress code
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __ASM_PLAT_UNCOMPRESS_H
+#define __ASM_PLAT_UNCOMPRESS_H
+
+typedef unsigned int upf_t;	/* cannot include linux/serial_core.h */
+
+/* uart setup */
+
+static unsigned int fifo_mask;
+static unsigned int fifo_max;
+
+/* forward declerations */
+
+static void arch_detect_cpu(void);
+
+/* defines for UART registers */
+
+#include "asm/plat-s3c/regs-serial.h"
+#include "asm/plat-s3c/regs-watchdog.h"
+
+/* working in physical space... */
+#undef S3C2410_WDOGREG
+#define S3C2410_WDOGREG(x) ((S3C24XX_PA_WATCHDOG + (x)))
+
+/* how many bytes we allow into the FIFO at a time in FIFO mode */
+#define FIFO_MAX	 (14)
+
+#define uart_base S3C24XX_PA_UART + (0x4000*CONFIG_S3C_LOWLEVEL_UART_PORT)
+
+static __inline__ void
+uart_wr(unsigned int reg, unsigned int val)
+{
+	volatile unsigned int *ptr;
+
+	ptr = (volatile unsigned int *)(reg + uart_base);
+	*ptr = val;
+}
+
+static __inline__ unsigned int
+uart_rd(unsigned int reg)
+{
+	volatile unsigned int *ptr;
+
+	ptr = (volatile unsigned int *)(reg + uart_base);
+	return *ptr;
+}
+
+/* we can deal with the case the UARTs are being run
+ * in FIFO mode, so that we don't hold up our execution
+ * waiting for tx to happen...
+*/
+
+static void putc(int ch)
+{
+	if (uart_rd(S3C2410_UFCON) & S3C2410_UFCON_FIFOMODE) {
+		int level;
+
+		while (1) {
+			level = uart_rd(S3C2410_UFSTAT);
+			level &= fifo_mask;
+
+			if (level < fifo_max)
+				break;
+		}
+
+	} else {
+		/* not using fifos */
+
+		while ((uart_rd(S3C2410_UTRSTAT) & S3C2410_UTRSTAT_TXE) != S3C2410_UTRSTAT_TXE)
+			barrier();
+	}
+
+	/* write byte to transmission register */
+	uart_wr(S3C2410_UTXH, ch);
+}
+
+static inline void flush(void)
+{
+}
+
+#define __raw_writel(d,ad) do { *((volatile unsigned int *)(ad)) = (d); } while(0)
+
+/* CONFIG_S3C_BOOT_WATCHDOG
+ *
+ * Simple boot-time watchdog setup, to reboot the system if there is
+ * any problem with the boot process
+*/
+
+#ifdef CONFIG_S3C_BOOT_WATCHDOG
+
+#define WDOG_COUNT (0xff00)
+
+static inline void arch_decomp_wdog(void)
+{
+	__raw_writel(WDOG_COUNT, S3C2410_WTCNT);
+}
+
+static void arch_decomp_wdog_start(void)
+{
+	__raw_writel(WDOG_COUNT, S3C2410_WTDAT);
+	__raw_writel(WDOG_COUNT, S3C2410_WTCNT);
+	__raw_writel(S3C2410_WTCON_ENABLE | S3C2410_WTCON_DIV128 | S3C2410_WTCON_RSTEN | S3C2410_WTCON_PRESCALE(0x80), S3C2410_WTCON);
+}
+
+#else
+#define arch_decomp_wdog_start()
+#define arch_decomp_wdog()
+#endif
+
+#ifdef CONFIG_S3C_BOOT_ERROR_RESET
+
+static void arch_decomp_error(const char *x)
+{
+	putstr("\n\n");
+	putstr(x);
+	putstr("\n\n -- System resetting\n");
+
+	__raw_writel(0x4000, S3C2410_WTDAT);
+	__raw_writel(0x4000, S3C2410_WTCNT);
+	__raw_writel(S3C2410_WTCON_ENABLE | S3C2410_WTCON_DIV128 | S3C2410_WTCON_RSTEN | S3C2410_WTCON_PRESCALE(0x40), S3C2410_WTCON);
+
+	while(1);
+}
+
+#define arch_error arch_decomp_error
+#endif
+
+static void error(char *err);
+
+static void
+arch_decomp_setup(void)
+{
+	/* we may need to setup the uart(s) here if we are not running
+	 * on an BAST... the BAST will have left the uarts configured
+	 * after calling linux.
+	 */
+
+	arch_detect_cpu();
+	arch_decomp_wdog_start();
+}
+
+
+#endif /* __ASM_PLAT_UNCOMPRESS_H */
diff --git a/include/asm-arm/arch-s3c2410/regs-iis.h b/include/asm-arm/plat-s3c24xx/regs-iis.h
similarity index 100%
rename from include/asm-arm/arch-s3c2410/regs-iis.h
rename to include/asm-arm/plat-s3c24xx/regs-iis.h
diff --git a/include/asm-arm/arch-s3c2410/regs-spi.h b/include/asm-arm/plat-s3c24xx/regs-spi.h
similarity index 100%
rename from include/asm-arm/arch-s3c2410/regs-spi.h
rename to include/asm-arm/plat-s3c24xx/regs-spi.h
diff --git a/include/asm-arm/arch-s3c2410/regs-udc.h b/include/asm-arm/plat-s3c24xx/regs-udc.h
similarity index 100%
rename from include/asm-arm/arch-s3c2410/regs-udc.h
rename to include/asm-arm/plat-s3c24xx/regs-udc.h
diff --git a/include/asm-arm/arch-s3c2410/udc.h b/include/asm-arm/plat-s3c24xx/udc.h
similarity index 100%
rename from include/asm-arm/arch-s3c2410/udc.h
rename to include/asm-arm/plat-s3c24xx/udc.h
diff --git a/include/asm-arm/thread_info.h b/include/asm-arm/thread_info.h
index eae85b0..69c65d5 100644
--- a/include/asm-arm/thread_info.h
+++ b/include/asm-arm/thread_info.h
@@ -24,7 +24,6 @@
 struct task_struct;
 struct exec_domain;
 
-#include <asm/ptrace.h>
 #include <asm/types.h>
 #include <asm/domain.h>
 
diff --git a/include/asm-arm/unistd.h b/include/asm-arm/unistd.h
index bfdbebe..d327b25 100644
--- a/include/asm-arm/unistd.h
+++ b/include/asm-arm/unistd.h
@@ -441,7 +441,6 @@
 /*
  * Unimplemented (or alternatively implemented) syscalls
  */
-#define __IGNORE_sync_file_range	1
 #define __IGNORE_fadvise64_64		1
 
 #endif /* __KERNEL__ */
diff --git a/include/asm-arm/vfp.h b/include/asm-arm/vfp.h
index 14c5e09..bd6be9d 100644
--- a/include/asm-arm/vfp.h
+++ b/include/asm-arm/vfp.h
@@ -26,8 +26,8 @@
 #define FPSID_REV_MASK		(0xF  << FPSID_REV_BIT)
 
 /* FPEXC bits */
-#define FPEXC_EXCEPTION		(1<<31)
-#define FPEXC_ENABLE		(1<<30)
+#define FPEXC_EX		(1 << 31)
+#define FPEXC_EN		(1 << 30)
 
 /* FPSCR bits */
 #define FPSCR_DEFAULT_NAN	(1<<25)