Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
diff --git a/Documentation/fujitsu/frv/mmu-layout.txt b/Documentation/fujitsu/frv/mmu-layout.txt
new file mode 100644
index 0000000..11dcc56
--- /dev/null
+++ b/Documentation/fujitsu/frv/mmu-layout.txt
@@ -0,0 +1,306 @@
+ =================================
+ FR451 MMU LINUX MEMORY MANAGEMENT
+ =================================
+
+============
+MMU HARDWARE
+============
+
+FR451 MMU Linux puts the MMU into EDAT mode whilst running. This means that it uses both the SAT
+registers and the DAT TLB to perform address translation.
+
+There are 8 IAMLR/IAMPR register pairs and 16 DAMLR/DAMPR register pairs for SAT mode.
+
+In DAT mode, there is also a TLB organised in cache format as 64 lines x 2 ways. Each line spans a
+16KB range of addresses, but can match a larger region.
+
+
+===========================
+MEMORY MANAGEMENT REGISTERS
+===========================
+
+Certain control registers are used by the kernel memory management routines:
+
+ REGISTERS USAGE
+ ====================== ==================================================
+ IAMR0, DAMR0 Kernel image and data mappings
+ IAMR1, DAMR1 First-chance TLB lookup mapping
+ DAMR2 Page attachment for cache flush by page
+ DAMR3 Current PGD mapping
+ SCR0, DAMR4 Instruction TLB PGE/PTD cache
+ SCR1, DAMR5 Data TLB PGE/PTD cache
+ DAMR6-10 kmap_atomic() mappings
+ DAMR11 I/O mapping
+ CXNR mm_struct context ID
+ TTBR Page directory (PGD) pointer (physical address)
+
+
+=====================
+GENERAL MEMORY LAYOUT
+=====================
+
+The physical memory layout is as follows:
+
+ PHYSICAL ADDRESS CONTROLLER DEVICE
+ =================== ============== =======================================
+ 00000000 - BFFFFFFF SDRAM SDRAM area
+ E0000000 - EFFFFFFF L-BUS CS2# VDK SLBUS/PCI window
+ F0000000 - F0FFFFFF L-BUS CS5# MB93493 CSC area (DAV daughter board)
+ F1000000 - F1FFFFFF L-BUS CS7# (CB70 CPU-card PCMCIA port I/O space)
+ FC000000 - FC0FFFFF L-BUS CS1# VDK MB86943 config space
+ FC100000 - FC1FFFFF L-BUS CS6# DM9000 NIC I/O space
+ FC200000 - FC2FFFFF L-BUS CS3# MB93493 CSR area (DAV daughter board)
+ FD000000 - FDFFFFFF L-BUS CS4# (CB70 CPU-card extra flash space)
+ FE000000 - FEFFFFFF Internal CPU peripherals
+ FF000000 - FF1FFFFF L-BUS CS0# Flash 1
+ FF200000 - FF3FFFFF L-BUS CS0# Flash 2
+ FFC00000 - FFC0001F L-BUS CS0# FPGA
+
+The virtual memory layout is:
+
+ VIRTUAL ADDRESS PHYSICAL TRANSLATOR FLAGS SIZE OCCUPATION
+ ================= ======== ============== ======= ======= ===================================
+ 00004000-BFFFFFFF various TLB,xAMR1 D-N-??V 3GB Userspace
+ C0000000-CFFFFFFF 00000000 xAMPR0 -L-S--V 256MB Kernel image and data
+ D0000000-D7FFFFFF various TLB,xAMR1 D-NS??V 128MB vmalloc area
+ D8000000-DBFFFFFF various TLB,xAMR1 D-NS??V 64MB kmap() area
+ DC000000-DCFFFFFF various TLB 1MB Secondary kmap_atomic() frame
+ DD000000-DD27FFFF various DAMR 160KB Primary kmap_atomic() frame
+ DD040000 DAMR2/IAMR2 -L-S--V page Page cache flush attachment point
+ DD080000 DAMR3 -L-SC-V page Page Directory (PGD)
+ DD0C0000 DAMR4 -L-SC-V page Cached insn TLB Page Table lookup
+ DD100000 DAMR5 -L-SC-V page Cached data TLB Page Table lookup
+ DD140000 DAMR6 -L-S--V page kmap_atomic(KM_BOUNCE_READ)
+ DD180000 DAMR7 -L-S--V page kmap_atomic(KM_SKB_SUNRPC_DATA)
+ DD1C0000 DAMR8 -L-S--V page kmap_atomic(KM_SKB_DATA_SOFTIRQ)
+ DD200000 DAMR9 -L-S--V page kmap_atomic(KM_USER0)
+ DD240000 DAMR10 -L-S--V page kmap_atomic(KM_USER1)
+ E0000000-FFFFFFFF E0000000 DAMR11 -L-SC-V 512MB I/O region
+
+IAMPR1 and DAMPR1 are used as an extension to the TLB.
+
+
+====================
+KMAP AND KMAP_ATOMIC
+====================
+
+To access pages in the page cache (which may not be directly accessible if highmem is available),
+the kernel calls kmap(), does the access and then calls kunmap(); or it calls kmap_atomic(), does
+the access and then calls kunmap_atomic().
+
+kmap() creates an attachment between an arbitrary inaccessible page and a range of virtual
+addresses by installing a PTE in a special page table. The kernel can then access this page as it
+wills. When it's finished, the kernel calls kunmap() to clear the PTE.
+
+kmap_atomic() does something slightly different. In the interests of speed, it chooses one of two
+strategies:
+
+ (1) If possible, kmap_atomic() attaches the requested page to one of DAMPR5 through DAMPR10
+ register pairs; and the matching kunmap_atomic() clears the DAMPR. This makes high memory
+ support really fast as there's no need to flush the TLB or modify the page tables. The DAMLR
+ registers being used for this are preset during boot and don't change over the lifetime of the
+ process. There's a direct mapping between the first few kmap_atomic() types, DAMR number and
+ virtual address slot.
+
+ However, there are more kmap_atomic() types defined than there are DAMR registers available,
+ so we fall back to:
+
+ (2) kmap_atomic() uses a slot in the secondary frame (determined by the type parameter), and then
+ locks an entry in the TLB to translate that slot to the specified page. The number of slots is
+ obviously limited, and their positions are controlled such that each slot is matched by a
+ different line in the TLB. kunmap() ejects the entry from the TLB.
+
+Note that the first three kmap atomic types are really just declared as placeholders. The DAMPR
+registers involved are actually modified directly.
+
+Also note that kmap() itself may sleep, kmap_atomic() may never sleep and both always succeed;
+furthermore, a driver using kmap() may sleep before calling kunmap(), but may not sleep before
+calling kunmap_atomic() if it had previously called kmap_atomic().
+
+
+===============================
+USING MORE THAN 256MB OF MEMORY
+===============================
+
+The kernel cannot access more than 256MB of memory directly. The physical layout, however, permits
+up to 3GB of SDRAM (possibly 3.25GB) to be made available. By using CONFIG_HIGHMEM, the kernel can
+allow userspace (by way of page tables) and itself (by way of kmap) to deal with the memory
+allocation.
+
+External devices can, of course, still DMA to and from all of the SDRAM, even if the kernel can't
+see it directly. The kernel translates page references into real addresses for communicating to the
+devices.
+
+
+===================
+PAGE TABLE TOPOLOGY
+===================
+
+The page tables are arranged in 2-layer format. There is a middle layer (PMD) that would be used in
+3-layer format tables but that is folded into the top layer (PGD) and so consumes no extra memory
+or processing power.
+
+ +------+ PGD PMD
+ | TTBR |--->+-------------------+
+ +------+ | | : STE |
+ | PGE0 | PME0 : STE |
+ | | : STE |
+ +-------------------+ Page Table
+ | | : STE -------------->+--------+ +0x0000
+ | PGE1 | PME0 : STE -----------+ | PTE0 |
+ | | : STE -------+ | +--------+
+ +-------------------+ | | | PTE63 |
+ | | : STE | | +-->+--------+ +0x0100
+ | PGE2 | PME0 : STE | | | PTE64 |
+ | | : STE | | +--------+
+ +-------------------+ | | PTE127 |
+ | | : STE | +------>+--------+ +0x0200
+ | PGE3 | PME0 : STE | | PTE128 |
+ | | : STE | +--------+
+ +-------------------+ | PTE191 |
+ +--------+ +0x0300
+
+Each Page Directory (PGD) is 16KB (page size) in size and is divided into 64 entries (PGEs). Each
+PGE contains one Page Mid Directory (PMD).
+
+Each PMD is 256 bytes in size and contains a single entry (PME). Each PME holds 64 FR451 MMU
+segment table entries of 4 bytes apiece. Each PME "points to" a page table. In practice, each STE
+points to a subset of the page table, the first to PT+0x0000, the second to PT+0x0100, the third to
+PT+0x200, and so on.
+
+Each PGE and PME covers 64MB of the total virtual address space.
+
+Each Page Table (PTD) is 16KB (page size) in size, and is divided into 4096 entries (PTEs). Each
+entry can point to one 16KB page. In practice, each Linux page table is subdivided into 64 FR451
+MMU page tables. But they are all grouped together to make management easier, in particular rmap
+support is then trivial.
+
+Grouping page tables in this fashion makes PGE caching in SCR0/SCR1 more efficient because the
+coverage of the cached item is greater.
+
+Page tables for the vmalloc area are allocated at boot time and shared between all mm_structs.
+
+
+=================
+USER SPACE LAYOUT
+=================
+
+For MMU capable Linux, the regions userspace code are allowed to access are kept entirely separate
+from those dedicated to the kernel:
+
+ VIRTUAL ADDRESS SIZE PURPOSE
+ ================= ===== ===================================
+ 00000000-00003fff 4KB NULL pointer access trap
+ 00004000-01ffffff ~32MB lower mmap space (grows up)
+ 02000000-021fffff 2MB Stack space (grows down from top)
+ 02200000-nnnnnnnn Executable mapping
+ nnnnnnnn- brk space (grows up)
+ -bfffffff upper mmap space (grows down)
+
+This is so arranged so as to make best use of the 16KB page tables and the way in which PGEs/PMEs
+are cached by the TLB handler. The lower mmap space is filled first, and then the upper mmap space
+is filled.
+
+
+===============================
+GDB-STUB MMU DEBUGGING SERVICES
+===============================
+
+The gdb-stub included in this kernel provides a number of services to aid in the debugging of MMU
+related kernel services:
+
+ (*) Every time the kernel stops, certain state information is dumped into __debug_mmu. This
+ variable is defined in arch/frv/kernel/gdb-stub.c. Note that the gdbinit file in this
+ directory has some useful macros for dealing with this.
+
+ (*) __debug_mmu.tlb[]
+
+ This receives the current TLB contents. This can be viewed with the _tlb GDB macro:
+
+ (gdb) _tlb
+ tlb[0x00]: 01000005 00718203 01000002 00718203
+ tlb[0x01]: 01004002 006d4201 01004005 006d4203
+ tlb[0x02]: 01008002 006d0201 01008006 00004200
+ tlb[0x03]: 0100c006 007f4202 0100c002 0064c202
+ tlb[0x04]: 01110005 00774201 01110002 00774201
+ tlb[0x05]: 01114005 00770201 01114002 00770201
+ tlb[0x06]: 01118002 0076c201 01118005 0076c201
+ ...
+ tlb[0x3d]: 010f4002 00790200 001f4002 0054ca02
+ tlb[0x3e]: 010f8005 0078c201 010f8002 0078c201
+ tlb[0x3f]: 001fc002 0056ca01 001fc005 00538a01
+
+ (*) __debug_mmu.iamr[]
+ (*) __debug_mmu.damr[]
+
+ These receive the current IAMR and DAMR contents. These can be viewed with with the _amr
+ GDB macro:
+
+ (gdb) _amr
+ AMRx DAMR IAMR
+ ==== ===================== =====================
+ amr0 : L:c0000000 P:00000cb9 : L:c0000000 P:000004b9
+ amr1 : L:01070005 P:006f9203 : L:0102c005 P:006a1201
+ amr2 : L:d8d00000 P:00000000 : L:d8d00000 P:00000000
+ amr3 : L:d8d04000 P:00534c0d : L:00000000 P:00000000
+ amr4 : L:d8d08000 P:00554c0d : L:00000000 P:00000000
+ amr5 : L:d8d0c000 P:00554c0d : L:00000000 P:00000000
+ amr6 : L:d8d10000 P:00000000 : L:00000000 P:00000000
+ amr7 : L:d8d14000 P:00000000 : L:00000000 P:00000000
+ amr8 : L:d8d18000 P:00000000
+ amr9 : L:d8d1c000 P:00000000
+ amr10: L:d8d20000 P:00000000
+ amr11: L:e0000000 P:e0000ccd
+
+ (*) The current task's page directory is bound to DAMR3.
+
+ This can be viewed with the _pgd GDB macro:
+
+ (gdb) _pgd
+ $3 = {{pge = {{ste = {0x554001, 0x554101, 0x554201, 0x554301, 0x554401,
+ 0x554501, 0x554601, 0x554701, 0x554801, 0x554901, 0x554a01,
+ 0x554b01, 0x554c01, 0x554d01, 0x554e01, 0x554f01, 0x555001,
+ 0x555101, 0x555201, 0x555301, 0x555401, 0x555501, 0x555601,
+ 0x555701, 0x555801, 0x555901, 0x555a01, 0x555b01, 0x555c01,
+ 0x555d01, 0x555e01, 0x555f01, 0x556001, 0x556101, 0x556201,
+ 0x556301, 0x556401, 0x556501, 0x556601, 0x556701, 0x556801,
+ 0x556901, 0x556a01, 0x556b01, 0x556c01, 0x556d01, 0x556e01,
+ 0x556f01, 0x557001, 0x557101, 0x557201, 0x557301, 0x557401,
+ 0x557501, 0x557601, 0x557701, 0x557801, 0x557901, 0x557a01,
+ 0x557b01, 0x557c01, 0x557d01, 0x557e01, 0x557f01}}}}, {pge = {{
+ ste = {0x0 <repeats 64 times>}}}} <repeats 51 times>, {pge = {{ste = {
+ 0x248001, 0x248101, 0x248201, 0x248301, 0x248401, 0x248501,
+ 0x248601, 0x248701, 0x248801, 0x248901, 0x248a01, 0x248b01,
+ 0x248c01, 0x248d01, 0x248e01, 0x248f01, 0x249001, 0x249101,
+ 0x249201, 0x249301, 0x249401, 0x249501, 0x249601, 0x249701,
+ 0x249801, 0x249901, 0x249a01, 0x249b01, 0x249c01, 0x249d01,
+ 0x249e01, 0x249f01, 0x24a001, 0x24a101, 0x24a201, 0x24a301,
+ 0x24a401, 0x24a501, 0x24a601, 0x24a701, 0x24a801, 0x24a901,
+ 0x24aa01, 0x24ab01, 0x24ac01, 0x24ad01, 0x24ae01, 0x24af01,
+ 0x24b001, 0x24b101, 0x24b201, 0x24b301, 0x24b401, 0x24b501,
+ 0x24b601, 0x24b701, 0x24b801, 0x24b901, 0x24ba01, 0x24bb01,
+ 0x24bc01, 0x24bd01, 0x24be01, 0x24bf01}}}}, {pge = {{ste = {
+ 0x0 <repeats 64 times>}}}} <repeats 11 times>}
+
+ (*) The PTD last used by the instruction TLB miss handler is attached to DAMR4.
+ (*) The PTD last used by the data TLB miss handler is attached to DAMR5.
+
+ These can be viewed with the _ptd_i and _ptd_d GDB macros:
+
+ (gdb) _ptd_d
+ $5 = {{pte = 0x0} <repeats 127 times>, {pte = 0x539b01}, {
+ pte = 0x0} <repeats 896 times>, {pte = 0x719303}, {pte = 0x6d5303}, {
+ pte = 0x0}, {pte = 0x0}, {pte = 0x0}, {pte = 0x0}, {pte = 0x0}, {
+ pte = 0x0}, {pte = 0x0}, {pte = 0x0}, {pte = 0x0}, {pte = 0x6a1303}, {
+ pte = 0x0} <repeats 12 times>, {pte = 0x709303}, {pte = 0x0}, {pte = 0x0},
+ {pte = 0x6fd303}, {pte = 0x6f9303}, {pte = 0x6f5303}, {pte = 0x0}, {
+ pte = 0x6ed303}, {pte = 0x531b01}, {pte = 0x50db01}, {
+ pte = 0x0} <repeats 13 times>, {pte = 0x5303}, {pte = 0x7f5303}, {
+ pte = 0x509b01}, {pte = 0x505b01}, {pte = 0x7c9303}, {pte = 0x7b9303}, {
+ pte = 0x7b5303}, {pte = 0x7b1303}, {pte = 0x7ad303}, {pte = 0x0}, {
+ pte = 0x0}, {pte = 0x7a1303}, {pte = 0x0}, {pte = 0x795303}, {pte = 0x0}, {
+ pte = 0x78d303}, {pte = 0x0}, {pte = 0x0}, {pte = 0x0}, {pte = 0x0}, {
+ pte = 0x0}, {pte = 0x775303}, {pte = 0x771303}, {pte = 0x76d303}, {
+ pte = 0x0}, {pte = 0x765303}, {pte = 0x7c5303}, {pte = 0x501b01}, {
+ pte = 0x4f1b01}, {pte = 0x4edb01}, {pte = 0x0}, {pte = 0x4f9b01}, {
+ pte = 0x4fdb01}, {pte = 0x0} <repeats 2992 times>}