diff --git a/Documentation/00-INDEX b/Documentation/00-INDEX
index 30b327a..042073f 100644
--- a/Documentation/00-INDEX
+++ b/Documentation/00-INDEX
@@ -183,8 +183,6 @@
 	- directory with info about Linux on Intel 32 bit architecture.
 ia64/
 	- directory with info about Linux on Intel 64 bit architecture.
-ide.txt
-	- important info for users of ATA devices (IDE/EIDE disks and CD-ROMS).
 infiniband/
 	- directory with documents concerning Linux InfiniBand support.
 initrd.txt
diff --git a/Documentation/cdrom/ide-cd b/Documentation/cdrom/ide-cd
index 29721bf..91c0dcc 100644
--- a/Documentation/cdrom/ide-cd
+++ b/Documentation/cdrom/ide-cd
@@ -45,7 +45,7 @@
 ---------------
 
 0. The ide-cd relies on the ide disk driver.  See
-   Documentation/ide.txt for up-to-date information on the ide
+   Documentation/ide/ide.txt for up-to-date information on the ide
    driver.
 
 1. Make sure that the ide and ide-cd drivers are compiled into the
@@ -64,7 +64,7 @@
 
    Depending on what type of IDE interface you have, you may need to
    specify additional configuration options.  See
-   Documentation/ide.txt.
+   Documentation/ide/ide.txt.
 
 2. You should also ensure that the iso9660 filesystem is either
    compiled into the kernel or available as a loadable module.  You
@@ -84,7 +84,7 @@
    on the primary IDE interface are called `hda' and `hdb',
    respectively.  The drives on the secondary interface are called
    `hdc' and `hdd'.  (Interfaces at other locations get other letters
-   in the third position; see Documentation/ide.txt.)
+   in the third position; see Documentation/ide/ide.txt.)
 
    If you want your CDROM drive to be found automatically by the
    driver, you should make sure your IDE interface uses either the
@@ -93,7 +93,7 @@
    be jumpered as `master'.  (If for some reason you cannot configure
    your system in this manner, you can probably still use the driver.
    You may have to pass extra configuration information to the kernel
-   when you boot, however.  See Documentation/ide.txt for more
+   when you boot, however.  See Documentation/ide/ide.txt for more
    information.)
 
 4. Boot the system.  If the drive is recognized, you should see a
@@ -201,7 +201,7 @@
 This section discusses some common problems encountered when trying to
 use the driver, and some possible solutions.  Note that if you are
 experiencing problems, you should probably also review
-Documentation/ide.txt for current information about the underlying
+Documentation/ide/ide.txt for current information about the underlying
 IDE support code.  Some of these items apply only to earlier versions
 of the driver, but are mentioned here for completeness.
 
@@ -211,7 +211,7 @@
 a. Drive is not detected during booting.
 
    - Review the configuration instructions above and in
-     Documentation/ide.txt, and check how your hardware is
+     Documentation/ide/ide.txt, and check how your hardware is
      configured.
 
    - If your drive is the only device on an IDE interface, it should
@@ -219,7 +219,7 @@
 
    - If your IDE interface is not at the standard addresses of 0x170
      or 0x1f0, you'll need to explicitly inform the driver using a
-     lilo option.  See Documentation/ide.txt.  (This feature was
+     lilo option.  See Documentation/ide/ide.txt.  (This feature was
      added around kernel version 1.3.30.)
 
    - If the autoprobing is not finding your drive, you can tell the
@@ -245,7 +245,7 @@
      Support for some interfaces needing extra initialization is
      provided in later 1.3.x kernels.  You may need to turn on
      additional kernel configuration options to get them to work;
-     see Documentation/ide.txt.
+     see Documentation/ide/ide.txt.
 
      Even if support is not available for your interface, you may be
      able to get it to work with the following procedure.  First boot
@@ -299,7 +299,7 @@
     be worked around by specifying the `serialize' option when
     booting.  Recent kernels should be able to detect the need for
     this automatically in most cases, but the detection is not
-    foolproof.  See Documentation/ide.txt for more information
+    foolproof.  See Documentation/ide/ide.txt for more information
     about the `serialize' option and the CMD640B.
 
   - Note that many MS-DOS CDROM drivers will work with such buggy
diff --git a/Documentation/ide/00-INDEX b/Documentation/ide/00-INDEX
new file mode 100644
index 0000000..d6b7788
--- /dev/null
+++ b/Documentation/ide/00-INDEX
@@ -0,0 +1,12 @@
+00-INDEX
+    	- this file
+ChangeLog.ide-cd.1994-2004
+	- ide-cd changelog
+ChangeLog.ide-floppy.1996-2002
+	- ide-floppy changelog
+ChangeLog.ide-tape.1995-2002
+	- ide-tape changelog
+ide-tape.txt
+	- info on the IDE ATAPI streaming tape driver
+ide.txt
+	- important info for users of ATA devices (IDE/EIDE disks and CD-ROMS).
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index 9a5b665..533e67f 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -712,7 +712,7 @@
 			Format: <cyl>,<head>,<sect>
 
 	hd?=		[HW] (E)IDE subsystem
-	hd?lun=		See Documentation/ide.txt.
+	hd?lun=		See Documentation/ide/ide.txt.
 
 	highmem=nn[KMG]	[KNL,BOOT] forces the highmem zone to have an exact
 			size of <nn>. This works even on boxes that have no
@@ -766,14 +766,14 @@
 
 	ide=		[HW] (E)IDE subsystem
 			Format: ide=nodma or ide=doubler or ide=reverse
-			See Documentation/ide.txt.
+			See Documentation/ide/ide.txt.
 
 	ide?=		[HW] (E)IDE subsystem
 			Format: ide?=noprobe or chipset specific parameters.
-			See Documentation/ide.txt.
+			See Documentation/ide/ide.txt.
 
 	idebus=		[HW] (E)IDE subsystem - VLB/PCI bus speed
-			See Documentation/ide.txt.
+			See Documentation/ide/ide.txt.
 
 	idle=		[X86]
 			Format: idle=poll or idle=mwait