MMC: Use timeout values from CSR

Hard-coded timeout values of 250ms for writes and 100ms for reads are
currently used for MMC transactions over SPI. The spec states that the
timeout values from the card should be used.

Signed-off-by: Matthew Fleming <matthew.fleming@imgtec.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
diff --git a/drivers/mmc/host/mmc_spi.c b/drivers/mmc/host/mmc_spi.c
index 7503b81..07faf54 100644
--- a/drivers/mmc/host/mmc_spi.c
+++ b/drivers/mmc/host/mmc_spi.c
@@ -95,8 +95,6 @@
  * reads which takes nowhere near that long.  Older cards may be able to use
  * shorter timeouts ... but why bother?
  */
-#define readblock_timeout	ktime_set(0, 100 * 1000 * 1000)
-#define writeblock_timeout	ktime_set(0, 250 * 1000 * 1000)
 #define r1b_timeout		ktime_set(3, 0)
 
 
@@ -220,9 +218,9 @@
 	return mmc_spi_skip(host, timeout, sizeof(host->data->status), 0);
 }
 
-static int mmc_spi_readtoken(struct mmc_spi_host *host)
+static int mmc_spi_readtoken(struct mmc_spi_host *host, ktime_t timeout)
 {
-	return mmc_spi_skip(host, readblock_timeout, 1, 0xff);
+	return mmc_spi_skip(host, timeout, 1, 0xff);
 }
 
 
@@ -605,7 +603,8 @@
  * Return negative errno, else success.
  */
 static int
-mmc_spi_writeblock(struct mmc_spi_host *host, struct spi_transfer *t)
+mmc_spi_writeblock(struct mmc_spi_host *host, struct spi_transfer *t,
+	ktime_t timeout)
 {
 	struct spi_device	*spi = host->spi;
 	int			status, i;
@@ -673,7 +672,7 @@
 		if (scratch->status[i] != 0)
 			return 0;
 	}
-	return mmc_spi_wait_unbusy(host, writeblock_timeout);
+	return mmc_spi_wait_unbusy(host, timeout);
 }
 
 /*
@@ -693,7 +692,8 @@
  * STOP_TRANSMISSION command.
  */
 static int
-mmc_spi_readblock(struct mmc_spi_host *host, struct spi_transfer *t)
+mmc_spi_readblock(struct mmc_spi_host *host, struct spi_transfer *t,
+	ktime_t timeout)
 {
 	struct spi_device	*spi = host->spi;
 	int			status;
@@ -707,7 +707,7 @@
 		return status;
 	status = scratch->status[0];
 	if (status == 0xff || status == 0)
-		status = mmc_spi_readtoken(host);
+		status = mmc_spi_readtoken(host, timeout);
 
 	if (status == SPI_TOKEN_SINGLE) {
 		if (host->dma_dev) {
@@ -778,6 +778,8 @@
 	struct scatterlist	*sg;
 	unsigned		n_sg;
 	int			multiple = (data->blocks > 1);
+	u32			clock_rate;
+	ktime_t			timeout;
 
 	if (data->flags & MMC_DATA_READ)
 		direction = DMA_FROM_DEVICE;
@@ -786,6 +788,14 @@
 	mmc_spi_setup_data_message(host, multiple, direction);
 	t = &host->t;
 
+	if (t->speed_hz)
+		clock_rate = t->speed_hz;
+	else
+		clock_rate = spi->max_speed_hz;
+
+	timeout = ktime_add_ns(ktime_set(0, 0), data->timeout_ns +
+			data->timeout_clks * 1000000 / clock_rate);
+
 	/* Handle scatterlist segments one at a time, with synch for
 	 * each 512-byte block
 	 */
@@ -832,9 +842,9 @@
 				t->len);
 
 			if (direction == DMA_TO_DEVICE)
-				status = mmc_spi_writeblock(host, t);
+				status = mmc_spi_writeblock(host, t, timeout);
 			else
-				status = mmc_spi_readblock(host, t);
+				status = mmc_spi_readblock(host, t, timeout);
 			if (status < 0)
 				break;
 
@@ -917,7 +927,7 @@
 			if (scratch->status[tmp] != 0)
 				return;
 		}
-		tmp = mmc_spi_wait_unbusy(host, writeblock_timeout);
+		tmp = mmc_spi_wait_unbusy(host, timeout);
 		if (tmp < 0 && !data->error)
 			data->error = tmp;
 	}