Merge branch 'for_paulus' of master.kernel.org:/pub/scm/linux/kernel/git/galak/powerpc
* 'for_paulus' of master.kernel.org:/pub/scm/linux/kernel/git/galak/powerpc: (25 commits)
[POWERPC] 85xx: Added needed MPC85xx PCI device IDs
[POWERPC] Add Freescale PCI VENDOR ID and 8641 device IDs
[POWERPC] 85xxCDS: MPC8548 DTS cleanup.
[POWERPC] 85xxCDS: Misc 8548 PCI Corrections.
[POWERPC] 85xxCDS: Delay 8259 cascade hookup.
[POWERPC] 85xxCDS: Make sure restart resets the PCI bus.
[POWERPC] 85xxCDS: Allow 8259 cascade to share an MPIC interrupt line.
[POWERPC] FSL: Add support for PCI-X controllers
[POWERPC] Make sure virtual P2P bridge registers are setup on PCIe PHB
[POWERPC] Provide ability to setup P2P bridge registers from struct resource
[POWERPC] Add basic PCI/PCI Express support for 8544DS board
[POWERPC] Make endianess of cfg_addr for indirect pci ops runtime
[POWERPC] Removed setup_indirect_pci_nomap
[POWERPC] 85xx: Add quirk to ignore bogus FPGA on CDS
[POWERPC] 85xx: Added 8568 PCIe support
[POWERPC] Fixup resources on pci_bus for PCIe PHB when no device is connected
[POWERPC] Add basic PCI node for mpc8568mds board
[POWERPC] Use Freescale pci/pcie common code for 85xx boards
[POWERPC] Update PCI nodes in the 83xx/85xx boards device tree
[POWERPC] Add 8548 CDS PCI express controller node and PCI-X device node
...
diff --git a/arch/powerpc/Kconfig b/arch/powerpc/Kconfig
index 853c282..00099ef 100644
--- a/arch/powerpc/Kconfig
+++ b/arch/powerpc/Kconfig
@@ -411,11 +411,6 @@
default y if 40x || 44x
default n
-config PPC_INDIRECT_PCI_BE
- bool
- depends PPC_INDIRECT_PCI
- default n
-
config EISA
bool
@@ -425,6 +420,10 @@
config FSL_SOC
bool
+config FSL_PCI
+ bool
+ select PPC_INDIRECT_PCI
+
# Yes MCA RS/6000s exist but Linux-PPC does not currently support any
config MCA
bool
diff --git a/arch/powerpc/boot/dts/mpc8313erdb.dts b/arch/powerpc/boot/dts/mpc8313erdb.dts
index a1533cc..c5adbe4 100644
--- a/arch/powerpc/boot/dts/mpc8313erdb.dts
+++ b/arch/powerpc/boot/dts/mpc8313erdb.dts
@@ -178,7 +178,7 @@
#size-cells = <2>;
#address-cells = <3>;
reg = <8500 100>;
- compatible = "83xx";
+ compatible = "fsl,mpc8349-pci";
device_type = "pci";
};
diff --git a/arch/powerpc/boot/dts/mpc832x_mds.dts b/arch/powerpc/boot/dts/mpc832x_mds.dts
index 4fc0c4d..f158ed7 100644
--- a/arch/powerpc/boot/dts/mpc832x_mds.dts
+++ b/arch/powerpc/boot/dts/mpc832x_mds.dts
@@ -154,7 +154,7 @@
#size-cells = <2>;
#address-cells = <3>;
reg = <8500 100>;
- compatible = "83xx";
+ compatible = "fsl,mpc8349-pci";
device_type = "pci";
};
diff --git a/arch/powerpc/boot/dts/mpc832x_rdb.dts b/arch/powerpc/boot/dts/mpc832x_rdb.dts
index 447c03f..7c4beff 100644
--- a/arch/powerpc/boot/dts/mpc832x_rdb.dts
+++ b/arch/powerpc/boot/dts/mpc832x_rdb.dts
@@ -123,7 +123,7 @@
#size-cells = <2>;
#address-cells = <3>;
reg = <8500 100>;
- compatible = "83xx";
+ compatible = "fsl,mpc8349-pci";
device_type = "pci";
};
diff --git a/arch/powerpc/boot/dts/mpc8349emitx.dts b/arch/powerpc/boot/dts/mpc8349emitx.dts
index ae9bca5..502f47c 100644
--- a/arch/powerpc/boot/dts/mpc8349emitx.dts
+++ b/arch/powerpc/boot/dts/mpc8349emitx.dts
@@ -197,7 +197,7 @@
#size-cells = <2>;
#address-cells = <3>;
reg = <8500 100>;
- compatible = "83xx";
+ compatible = "fsl,mpc8349-pci";
device_type = "pci";
};
@@ -222,7 +222,7 @@
#size-cells = <2>;
#address-cells = <3>;
reg = <8600 100>;
- compatible = "83xx";
+ compatible = "fsl,mpc8349-pci";
device_type = "pci";
};
diff --git a/arch/powerpc/boot/dts/mpc8349emitxgp.dts b/arch/powerpc/boot/dts/mpc8349emitxgp.dts
index f636528..0b83871 100644
--- a/arch/powerpc/boot/dts/mpc8349emitxgp.dts
+++ b/arch/powerpc/boot/dts/mpc8349emitxgp.dts
@@ -154,7 +154,7 @@
#size-cells = <2>;
#address-cells = <3>;
reg = <8600 100>;
- compatible = "83xx";
+ compatible = "fsl,mpc8349-pci";
device_type = "pci";
};
diff --git a/arch/powerpc/boot/dts/mpc834x_mds.dts b/arch/powerpc/boot/dts/mpc834x_mds.dts
index 310e877..4810997 100644
--- a/arch/powerpc/boot/dts/mpc834x_mds.dts
+++ b/arch/powerpc/boot/dts/mpc834x_mds.dts
@@ -241,7 +241,7 @@
#size-cells = <2>;
#address-cells = <3>;
reg = <8500 100>;
- compatible = "83xx";
+ compatible = "fsl,mpc8349-pci";
device_type = "pci";
};
@@ -301,7 +301,7 @@
#size-cells = <2>;
#address-cells = <3>;
reg = <8600 100>;
- compatible = "83xx";
+ compatible = "fsl,mpc8349-pci";
device_type = "pci";
};
diff --git a/arch/powerpc/boot/dts/mpc836x_mds.dts b/arch/powerpc/boot/dts/mpc836x_mds.dts
index 1e914f31..e3f7c12 100644
--- a/arch/powerpc/boot/dts/mpc836x_mds.dts
+++ b/arch/powerpc/boot/dts/mpc836x_mds.dts
@@ -169,7 +169,7 @@
#size-cells = <2>;
#address-cells = <3>;
reg = <8500 100>;
- compatible = "83xx";
+ compatible = "fsl,mpc8349-pci";
device_type = "pci";
};
diff --git a/arch/powerpc/boot/dts/mpc8540ads.dts b/arch/powerpc/boot/dts/mpc8540ads.dts
index 364a969..fc8dff9 100644
--- a/arch/powerpc/boot/dts/mpc8540ads.dts
+++ b/arch/powerpc/boot/dts/mpc8540ads.dts
@@ -258,7 +258,7 @@
#size-cells = <2>;
#address-cells = <3>;
reg = <8000 1000>;
- compatible = "85xx";
+ compatible = "fsl,mpc8540-pcix", "fsl,mpc8540-pci";
device_type = "pci";
};
diff --git a/arch/powerpc/boot/dts/mpc8541cds.dts b/arch/powerpc/boot/dts/mpc8541cds.dts
index 070206f..fb0b647 100644
--- a/arch/powerpc/boot/dts/mpc8541cds.dts
+++ b/arch/powerpc/boot/dts/mpc8541cds.dts
@@ -193,7 +193,7 @@
#size-cells = <2>;
#address-cells = <3>;
reg = <8000 1000>;
- compatible = "85xx";
+ compatible = "fsl,mpc8540-pci";
device_type = "pci";
i8259@19000 {
@@ -230,7 +230,7 @@
#size-cells = <2>;
#address-cells = <3>;
reg = <9000 1000>;
- compatible = "85xx";
+ compatible = "fsl,mpc8540-pci";
device_type = "pci";
};
diff --git a/arch/powerpc/boot/dts/mpc8544ds.dts b/arch/powerpc/boot/dts/mpc8544ds.dts
index 8285925..4a900c6 100644
--- a/arch/powerpc/boot/dts/mpc8544ds.dts
+++ b/arch/powerpc/boot/dts/mpc8544ds.dts
@@ -137,6 +137,217 @@
interrupt-parent = <&mpic>;
};
+ pci@8000 {
+ compatible = "fsl,mpc8540-pci";
+ device_type = "pci";
+ interrupt-map-mask = <f800 0 0 7>;
+ interrupt-map = <
+
+ /* IDSEL 0x11 J17 Slot 1 */
+ 8800 0 0 1 &mpic 2 1
+ 8800 0 0 2 &mpic 3 1
+ 8800 0 0 3 &mpic 4 1
+ 8800 0 0 4 &mpic 1 1
+
+ /* IDSEL 0x12 J16 Slot 2 */
+
+ 9000 0 0 1 &mpic 3 1
+ 9000 0 0 2 &mpic 4 1
+ 9000 0 0 3 &mpic 2 1
+ 9000 0 0 4 &mpic 1 1>;
+
+ interrupt-parent = <&mpic>;
+ interrupts = <18 2>;
+ bus-range = <0 ff>;
+ ranges = <02000000 0 80000000 80000000 0 10000000
+ 01000000 0 00000000 e2000000 0 00800000>;
+ clock-frequency = <3f940aa>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ reg = <8000 1000>;
+ };
+
+ pcie@9000 {
+ compatible = "fsl,mpc8548-pcie";
+ device_type = "pci";
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ reg = <9000 1000>;
+ bus-range = <0 ff>;
+ ranges = <02000000 0 90000000 90000000 0 10000000
+ 01000000 0 00000000 e3000000 0 00800000>;
+ clock-frequency = <1fca055>;
+ interrupt-parent = <&mpic>;
+ interrupts = <1a 2>;
+ interrupt-map-mask = <f800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 4 1
+ 0000 0 0 2 &mpic 5 1
+ 0000 0 0 3 &mpic 6 1
+ 0000 0 0 4 &mpic 7 1
+ >;
+ };
+
+ pcie@a000 {
+ compatible = "fsl,mpc8548-pcie";
+ device_type = "pci";
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ reg = <a000 1000>;
+ bus-range = <0 ff>;
+ ranges = <02000000 0 a0000000 a0000000 0 10000000
+ 01000000 0 00000000 e2800000 0 00800000>;
+ clock-frequency = <1fca055>;
+ interrupt-parent = <&mpic>;
+ interrupts = <19 2>;
+ interrupt-map-mask = <f800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 0 1
+ 0000 0 0 2 &mpic 1 1
+ 0000 0 0 3 &mpic 2 1
+ 0000 0 0 4 &mpic 3 1
+ >;
+ };
+
+ pcie@b000 {
+ compatible = "fsl,mpc8548-pcie";
+ device_type = "pci";
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ reg = <b000 1000>;
+ bus-range = <0 ff>;
+ ranges = <02000000 0 b0000000 b0000000 0 10000000
+ 01000000 0 00000000 e3800000 0 00800000>;
+ clock-frequency = <1fca055>;
+ interrupt-parent = <&mpic>;
+ interrupts = <1b 2>;
+ interrupt-map-mask = <f800 0 0 7>;
+ interrupt-map = <
+
+ // IDSEL 0x1a
+ d000 0 0 1 &i8259 6 2
+ d000 0 0 2 &i8259 3 2
+ d000 0 0 3 &i8259 4 2
+ d000 0 0 4 &i8259 5 2
+
+ // IDSEL 0x1b
+ d800 0 0 1 &i8259 5 2
+ d800 0 0 2 &i8259 0 0
+ d800 0 0 3 &i8259 0 0
+ d800 0 0 4 &i8259 0 0
+
+ // IDSEL 0x1c USB
+ e000 0 0 1 &i8259 9 2
+ e000 0 0 2 &i8259 a 2
+ e000 0 0 3 &i8259 c 2
+ e000 0 0 4 &i8259 7 2
+
+ // IDSEL 0x1d Audio
+ e800 0 0 1 &i8259 9 2
+ e800 0 0 2 &i8259 a 2
+ e800 0 0 3 &i8259 b 2
+ e800 0 0 4 &i8259 0 0
+
+ // IDSEL 0x1e Legacy
+ f000 0 0 1 &i8259 c 2
+ f000 0 0 2 &i8259 0 0
+ f000 0 0 3 &i8259 0 0
+ f000 0 0 4 &i8259 0 0
+
+ // IDSEL 0x1f IDE/SATA
+ f800 0 0 1 &i8259 6 2
+ f800 0 0 2 &i8259 0 0
+ f800 0 0 3 &i8259 0 0
+ f800 0 0 4 &i8259 0 0
+ >;
+ uli1575@0 {
+ reg = <0 0 0 0 0>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ ranges = <02000000 0 b0000000
+ 02000000 0 b0000000
+ 0 10000000
+ 01000000 0 00000000
+ 01000000 0 00000000
+ 0 00080000>;
+
+ pci_bridge@0 {
+ reg = <0 0 0 0 0>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ ranges = <02000000 0 b0000000
+ 02000000 0 b0000000
+ 0 20000000
+ 01000000 0 00000000
+ 01000000 0 00000000
+ 0 00100000>;
+
+ isa@1e {
+ device_type = "isa";
+ #interrupt-cells = <2>;
+ #size-cells = <1>;
+ #address-cells = <2>;
+ reg = <f000 0 0 0 0>;
+ ranges = <1 0 01000000 0 0
+ 00001000>;
+ interrupt-parent = <&i8259>;
+
+ i8259: interrupt-controller@20 {
+ reg = <1 20 2
+ 1 a0 2
+ 1 4d0 2>;
+ clock-frequency = <0>;
+ interrupt-controller;
+ device_type = "interrupt-controller";
+ #address-cells = <0>;
+ #interrupt-cells = <2>;
+ built-in;
+ compatible = "chrp,iic";
+ interrupts = <9 2>;
+ interrupt-parent =
+ <&mpic>;
+ };
+
+ i8042@60 {
+ #size-cells = <0>;
+ #address-cells = <1>;
+ reg = <1 60 1 1 64 1>;
+ interrupts = <1 3 c 3>;
+ interrupt-parent =
+ <&i8259>;
+
+ keyboard@0 {
+ reg = <0>;
+ compatible = "pnpPNP,303";
+ };
+
+ mouse@1 {
+ reg = <1>;
+ compatible = "pnpPNP,f03";
+ };
+ };
+
+ rtc@70 {
+ compatible =
+ "pnpPNP,b00";
+ reg = <1 70 2>;
+ };
+
+ gpio@400 {
+ reg = <1 400 80>;
+ };
+ };
+ };
+ };
+
+ };
+
mpic: pic@40000 {
clock-frequency = <0>;
interrupt-controller;
diff --git a/arch/powerpc/boot/dts/mpc8548cds.dts b/arch/powerpc/boot/dts/mpc8548cds.dts
index 9d0b84b..d215d21 100644
--- a/arch/powerpc/boot/dts/mpc8548cds.dts
+++ b/arch/powerpc/boot/dts/mpc8548cds.dts
@@ -1,5 +1,5 @@
/*
- * MPC8555 CDS Device Tree Source
+ * MPC8548 CDS Device Tree Source
*
* Copyright 2006 Freescale Semiconductor Inc.
*
@@ -44,8 +44,14 @@
#size-cells = <1>;
#interrupt-cells = <2>;
device_type = "soc";
- ranges = <0 e0000000 00100000>;
- reg = <e0000000 00100000>; // CCSRBAR 1M
+ ranges = <00001000 e0001000 000ff000
+ 80000000 80000000 10000000
+ e2000000 e2000000 00800000
+ 90000000 90000000 10000000
+ e2800000 e2800000 00800000
+ a0000000 a0000000 20000000
+ e3000000 e3000000 01000000>;
+ reg = <e0000000 00001000>; // CCSRBAR
bus-frequency = <0>;
memory-controller@2000 {
@@ -162,8 +168,8 @@
serial@4500 {
device_type = "serial";
compatible = "ns16550";
- reg = <4500 100>; // reg base, size
- clock-frequency = <0>; // should we fill in in uboot?
+ reg = <4500 100>; // reg base, size
+ clock-frequency = <0>; // should we fill in in uboot?
interrupts = <2a 2>;
interrupt-parent = <&mpic>;
};
@@ -172,7 +178,7 @@
device_type = "serial";
compatible = "ns16550";
reg = <4600 100>; // reg base, size
- clock-frequency = <0>; // should we fill in in uboot?
+ clock-frequency = <0>; // should we fill in in uboot?
interrupts = <2a 2>;
interrupt-parent = <&mpic>;
};
@@ -183,77 +189,154 @@
fsl,has-rstcr;
};
- pci1: pci@8000 {
- interrupt-map-mask = <1f800 0 0 7>;
+ pci@8000 {
+ interrupt-map-mask = <f800 0 0 7>;
interrupt-map = <
+ /* IDSEL 0x4 (PCIX Slot 2) */
+ 02000 0 0 1 &mpic 0 1
+ 02000 0 0 2 &mpic 1 1
+ 02000 0 0 3 &mpic 2 1
+ 02000 0 0 4 &mpic 3 1
- /* IDSEL 0x10 */
- 08000 0 0 1 &mpic 0 1
- 08000 0 0 2 &mpic 1 1
- 08000 0 0 3 &mpic 2 1
- 08000 0 0 4 &mpic 3 1
+ /* IDSEL 0x5 (PCIX Slot 3) */
+ 02800 0 0 1 &mpic 1 1
+ 02800 0 0 2 &mpic 2 1
+ 02800 0 0 3 &mpic 3 1
+ 02800 0 0 4 &mpic 0 1
- /* IDSEL 0x11 */
- 08800 0 0 1 &mpic 0 1
- 08800 0 0 2 &mpic 1 1
- 08800 0 0 3 &mpic 2 1
- 08800 0 0 4 &mpic 3 1
+ /* IDSEL 0x6 (PCIX Slot 4) */
+ 03000 0 0 1 &mpic 2 1
+ 03000 0 0 2 &mpic 3 1
+ 03000 0 0 3 &mpic 0 1
+ 03000 0 0 4 &mpic 1 1
- /* IDSEL 0x12 (Slot 1) */
- 09000 0 0 1 &mpic 0 1
- 09000 0 0 2 &mpic 1 1
- 09000 0 0 3 &mpic 2 1
- 09000 0 0 4 &mpic 3 1
+ /* IDSEL 0x8 (PCIX Slot 5) */
+ 04000 0 0 1 &mpic 0 1
+ 04000 0 0 2 &mpic 1 1
+ 04000 0 0 3 &mpic 2 1
+ 04000 0 0 4 &mpic 3 1
- /* IDSEL 0x13 (Slot 2) */
- 09800 0 0 1 &mpic 1 1
- 09800 0 0 2 &mpic 2 1
- 09800 0 0 3 &mpic 3 1
- 09800 0 0 4 &mpic 0 1
+ /* IDSEL 0xC (Tsi310 bridge) */
+ 06000 0 0 1 &mpic 0 1
+ 06000 0 0 2 &mpic 1 1
+ 06000 0 0 3 &mpic 2 1
+ 06000 0 0 4 &mpic 3 1
- /* IDSEL 0x14 (Slot 3) */
- 0a000 0 0 1 &mpic 2 1
- 0a000 0 0 2 &mpic 3 1
- 0a000 0 0 3 &mpic 0 1
- 0a000 0 0 4 &mpic 1 1
+ /* IDSEL 0x14 (Slot 2) */
+ 0a000 0 0 1 &mpic 0 1
+ 0a000 0 0 2 &mpic 1 1
+ 0a000 0 0 3 &mpic 2 1
+ 0a000 0 0 4 &mpic 3 1
- /* IDSEL 0x15 (Slot 4) */
- 0a800 0 0 1 &mpic 3 1
- 0a800 0 0 2 &mpic 0 1
- 0a800 0 0 3 &mpic 1 1
- 0a800 0 0 4 &mpic 2 1
+ /* IDSEL 0x15 (Slot 3) */
+ 0a800 0 0 1 &mpic 1 1
+ 0a800 0 0 2 &mpic 2 1
+ 0a800 0 0 3 &mpic 3 1
+ 0a800 0 0 4 &mpic 0 1
- /* Bus 1 (Tundra Bridge) */
- /* IDSEL 0x12 (ISA bridge) */
- 19000 0 0 1 &mpic 0 1
- 19000 0 0 2 &mpic 1 1
- 19000 0 0 3 &mpic 2 1
- 19000 0 0 4 &mpic 3 1>;
+ /* IDSEL 0x16 (Slot 4) */
+ 0b000 0 0 1 &mpic 2 1
+ 0b000 0 0 2 &mpic 3 1
+ 0b000 0 0 3 &mpic 0 1
+ 0b000 0 0 4 &mpic 1 1
+
+ /* IDSEL 0x18 (Slot 5) */
+ 0c000 0 0 1 &mpic 0 1
+ 0c000 0 0 2 &mpic 1 1
+ 0c000 0 0 3 &mpic 2 1
+ 0c000 0 0 4 &mpic 3 1
+
+ /* IDSEL 0x1C (Tsi310 bridge PCI primary) */
+ 0E000 0 0 1 &mpic 0 1
+ 0E000 0 0 2 &mpic 1 1
+ 0E000 0 0 3 &mpic 2 1
+ 0E000 0 0 4 &mpic 3 1>;
+
interrupt-parent = <&mpic>;
interrupts = <18 2>;
bus-range = <0 0>;
- ranges = <02000000 0 80000000 80000000 0 20000000
- 01000000 0 00000000 e2000000 0 00100000>;
+ ranges = <02000000 0 80000000 80000000 0 10000000
+ 01000000 0 00000000 e2000000 0 00800000>;
clock-frequency = <3f940aa>;
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
reg = <8000 1000>;
- compatible = "85xx";
+ compatible = "fsl,mpc8540-pcix", "fsl,mpc8540-pci";
device_type = "pci";
- i8259@19000 {
- clock-frequency = <0>;
- interrupt-controller;
- device_type = "interrupt-controller";
- reg = <19000 0 0 0 1>;
- #address-cells = <0>;
- #interrupt-cells = <2>;
- built-in;
- compatible = "chrp,iic";
- big-endian;
- interrupts = <1>;
- interrupt-parent = <&pci1>;
+ pci_bridge@1c {
+ interrupt-map-mask = <f800 0 0 7>;
+ interrupt-map = <
+
+ /* IDSEL 0x00 (PrPMC Site) */
+ 0000 0 0 1 &mpic 0 1
+ 0000 0 0 2 &mpic 1 1
+ 0000 0 0 3 &mpic 2 1
+ 0000 0 0 4 &mpic 3 1
+
+ /* IDSEL 0x04 (VIA chip) */
+ 2000 0 0 1 &mpic 0 1
+ 2000 0 0 2 &mpic 1 1
+ 2000 0 0 3 &mpic 2 1
+ 2000 0 0 4 &mpic 3 1
+
+ /* IDSEL 0x05 (8139) */
+ 2800 0 0 1 &mpic 1 1
+
+ /* IDSEL 0x06 (Slot 6) */
+ 3000 0 0 1 &mpic 2 1
+ 3000 0 0 2 &mpic 3 1
+ 3000 0 0 3 &mpic 0 1
+ 3000 0 0 4 &mpic 1 1
+
+ /* IDESL 0x07 (Slot 7) */
+ 3800 0 0 1 &mpic 3 1
+ 3800 0 0 2 &mpic 0 1
+ 3800 0 0 3 &mpic 1 1
+ 3800 0 0 4 &mpic 2 1>;
+
+ reg = <e000 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ ranges = <02000000 0 80000000
+ 02000000 0 80000000
+ 0 20000000
+ 01000000 0 00000000
+ 01000000 0 00000000
+ 0 00080000>;
+ clock-frequency = <1fca055>;
+
+ isa@4 {
+ device_type = "isa";
+ #interrupt-cells = <2>;
+ #size-cells = <1>;
+ #address-cells = <2>;
+ reg = <2000 0 0 0 0>;
+ ranges = <1 0 01000000 0 0 00001000>;
+ interrupt-parent = <&i8259>;
+
+ i8259: interrupt-controller@20 {
+ clock-frequency = <0>;
+ interrupt-controller;
+ device_type = "interrupt-controller";
+ reg = <1 20 2
+ 1 a0 2
+ 1 4d0 2>;
+ #address-cells = <0>;
+ #interrupt-cells = <2>;
+ built-in;
+ compatible = "chrp,iic";
+ interrupts = <0 1>;
+ interrupt-parent = <&mpic>;
+ };
+
+ rtc@70 {
+ compatible = "pnpPNP,b00";
+ reg = <1 70 2>;
+ };
+ };
};
};
@@ -263,20 +346,45 @@
/* IDSEL 0x15 */
a800 0 0 1 &mpic b 1
- a800 0 0 2 &mpic b 1
- a800 0 0 3 &mpic b 1
- a800 0 0 4 &mpic b 1>;
+ a800 0 0 2 &mpic 1 1
+ a800 0 0 3 &mpic 2 1
+ a800 0 0 4 &mpic 3 1>;
+
interrupt-parent = <&mpic>;
interrupts = <19 2>;
bus-range = <0 0>;
- ranges = <02000000 0 a0000000 a0000000 0 20000000
- 01000000 0 00000000 e3000000 0 00100000>;
+ ranges = <02000000 0 90000000 90000000 0 10000000
+ 01000000 0 00000000 e2800000 0 00800000>;
clock-frequency = <3f940aa>;
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
reg = <9000 1000>;
- compatible = "85xx";
+ compatible = "fsl,mpc8540-pci";
+ device_type = "pci";
+ };
+ /* PCI Express */
+ pcie@a000 {
+ interrupt-map-mask = <f800 0 0 7>;
+ interrupt-map = <
+
+ /* IDSEL 0x0 (PEX) */
+ 00000 0 0 1 &mpic 0 1
+ 00000 0 0 2 &mpic 1 1
+ 00000 0 0 3 &mpic 2 1
+ 00000 0 0 4 &mpic 3 1>;
+
+ interrupt-parent = <&mpic>;
+ interrupts = <1a 2>;
+ bus-range = <0 ff>;
+ ranges = <02000000 0 a0000000 a0000000 0 20000000
+ 01000000 0 00000000 e3000000 0 08000000>;
+ clock-frequency = <1fca055>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ reg = <a000 1000>;
+ compatible = "fsl,mpc8548-pcie";
device_type = "pci";
};
diff --git a/arch/powerpc/boot/dts/mpc8555cds.dts b/arch/powerpc/boot/dts/mpc8555cds.dts
index 17e45d9..c3c8882 100644
--- a/arch/powerpc/boot/dts/mpc8555cds.dts
+++ b/arch/powerpc/boot/dts/mpc8555cds.dts
@@ -193,7 +193,7 @@
#size-cells = <2>;
#address-cells = <3>;
reg = <8000 1000>;
- compatible = "85xx";
+ compatible = "fsl,mpc8540-pci";
device_type = "pci";
i8259@19000 {
@@ -230,7 +230,7 @@
#size-cells = <2>;
#address-cells = <3>;
reg = <9000 1000>;
- compatible = "85xx";
+ compatible = "fsl,mpc8540-pci";
device_type = "pci";
};
diff --git a/arch/powerpc/boot/dts/mpc8560ads.dts b/arch/powerpc/boot/dts/mpc8560ads.dts
index 21ccaaa..16dbe84 100644
--- a/arch/powerpc/boot/dts/mpc8560ads.dts
+++ b/arch/powerpc/boot/dts/mpc8560ads.dts
@@ -136,7 +136,7 @@
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
- compatible = "85xx";
+ compatible = "fsl,mpc8540-pcix", "fsl,mpc8540-pci";
device_type = "pci";
reg = <8000 1000>;
clock-frequency = <3f940aa>;
diff --git a/arch/powerpc/boot/dts/mpc8568mds.dts b/arch/powerpc/boot/dts/mpc8568mds.dts
index 6bb18f2..99fa5a0 100644
--- a/arch/powerpc/boot/dts/mpc8568mds.dts
+++ b/arch/powerpc/boot/dts/mpc8568mds.dts
@@ -170,6 +170,60 @@
interrupt-parent = <&mpic>;
};
+ pci@8000 {
+ interrupt-map-mask = <f800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x12 AD18 */
+ 9000 0 0 1 &mpic 5 1
+ 9000 0 0 2 &mpic 6 1
+ 9000 0 0 3 &mpic 7 1
+ 9000 0 0 4 &mpic 4 1
+
+ /* IDSEL 0x13 AD19 */
+ 9800 0 0 1 &mpic 6 1
+ 9800 0 0 2 &mpic 7 1
+ 9800 0 0 3 &mpic 4 1
+ 9800 0 0 4 &mpic 5 1>;
+
+ interrupt-parent = <&mpic>;
+ interrupts = <18 2>;
+ bus-range = <0 ff>;
+ ranges = <02000000 0 80000000 80000000 0 20000000
+ 01000000 0 00000000 e2000000 0 00800000>;
+ clock-frequency = <3f940aa>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ reg = <8000 1000>;
+ compatible = "fsl,mpc8540-pci";
+ device_type = "pci";
+ };
+
+ /* PCI Express */
+ pcie@a000 {
+ interrupt-map-mask = <f800 0 0 7>;
+ interrupt-map = <
+
+ /* IDSEL 0x0 (PEX) */
+ 00000 0 0 1 &mpic 0 1
+ 00000 0 0 2 &mpic 1 1
+ 00000 0 0 3 &mpic 2 1
+ 00000 0 0 4 &mpic 3 1>;
+
+ interrupt-parent = <&mpic>;
+ interrupts = <1a 2>;
+ bus-range = <0 ff>;
+ ranges = <02000000 0 a0000000 a0000000 0 20000000
+ 01000000 0 00000000 e3000000 0 08000000>;
+ clock-frequency = <1fca055>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ reg = <a000 1000>;
+ compatible = "fsl,mpc8548-pcie";
+ device_type = "pci";
+ };
+
serial@4600 {
device_type = "serial";
compatible = "ns16550";
diff --git a/arch/powerpc/boot/dts/mpc8641_hpcn.dts b/arch/powerpc/boot/dts/mpc8641_hpcn.dts
index 6a78a2b..5d82709 100644
--- a/arch/powerpc/boot/dts/mpc8641_hpcn.dts
+++ b/arch/powerpc/boot/dts/mpc8641_hpcn.dts
@@ -211,8 +211,8 @@
interrupt-parent = <&mpic>;
};
- pci@8000 {
- compatible = "86xx";
+ pcie@8000 {
+ compatible = "fsl,mpc8641-pcie";
device_type = "pci";
#interrupt-cells = <1>;
#size-cells = <2>;
@@ -399,8 +399,8 @@
};
- pci@9000 {
- compatible = "86xx";
+ pcie@9000 {
+ compatible = "fsl,mpc8641-pcie";
device_type = "pci";
#interrupt-cells = <1>;
#size-cells = <2>;
diff --git a/arch/powerpc/configs/mpc8544_ds_defconfig b/arch/powerpc/configs/mpc8544_ds_defconfig
index c40a25a..7995231 100644
--- a/arch/powerpc/configs/mpc8544_ds_defconfig
+++ b/arch/powerpc/configs/mpc8544_ds_defconfig
@@ -1,9 +1,26 @@
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.22-rc7
-# Sun Jul 1 23:56:58 2007
+# Linux kernel version: 2.6.22
+# Fri Jul 20 14:09:13 2007
#
# CONFIG_PPC64 is not set
+
+#
+# Processor support
+#
+# CONFIG_6xx is not set
+CONFIG_PPC_85xx=y
+# CONFIG_PPC_8xx is not set
+# CONFIG_40x is not set
+# CONFIG_44x is not set
+# CONFIG_E200 is not set
+CONFIG_85xx=y
+CONFIG_E500=y
+CONFIG_BOOKE=y
+CONFIG_FSL_BOOKE=y
+# CONFIG_PHYS_64BIT is not set
+# CONFIG_SPE is not set
+# CONFIG_PPC_MM_SLICES is not set
CONFIG_PPC32=y
CONFIG_PPC_MERGE=y
CONFIG_MMU=y
@@ -14,6 +31,7 @@
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
+# CONFIG_ARCH_NO_VIRT_TO_BUS is not set
CONFIG_PPC=y
CONFIG_EARLY_PRINTK=y
CONFIG_GENERIC_NVRAM=y
@@ -25,28 +43,8 @@
CONFIG_AUDIT_ARCH=y
CONFIG_GENERIC_BUG=y
CONFIG_DEFAULT_UIMAGE=y
-
-#
-# Processor support
-#
-# CONFIG_CLASSIC32 is not set
-# CONFIG_PPC_82xx is not set
-# CONFIG_PPC_83xx is not set
-CONFIG_PPC_85xx=y
-# CONFIG_PPC_86xx is not set
-# CONFIG_PPC_8xx is not set
-# CONFIG_40x is not set
-# CONFIG_44x is not set
-# CONFIG_E200 is not set
-CONFIG_85xx=y
-CONFIG_E500=y
# CONFIG_PPC_DCR_NATIVE is not set
# CONFIG_PPC_DCR_MMIO is not set
-CONFIG_BOOKE=y
-CONFIG_FSL_BOOKE=y
-# CONFIG_PHYS_64BIT is not set
-# CONFIG_SPE is not set
-# CONFIG_PPC_MM_SLICES is not set
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
@@ -63,13 +61,12 @@
CONFIG_LOCALVERSION_AUTO=y
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
-CONFIG_IPC_NS=y
CONFIG_SYSVIPC_SYSCTL=y
CONFIG_POSIX_MQUEUE=y
CONFIG_BSD_PROCESS_ACCT=y
# CONFIG_BSD_PROCESS_ACCT_V3 is not set
# CONFIG_TASKSTATS is not set
-# CONFIG_UTS_NS is not set
+# CONFIG_USER_NS is not set
CONFIG_AUDIT=y
# CONFIG_AUDITSYSCALL is not set
CONFIG_IKCONFIG=y
@@ -86,7 +83,7 @@
CONFIG_KALLSYMS=y
CONFIG_KALLSYMS_ALL=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
-# CONFIG_HOTPLUG is not set
+CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
@@ -105,24 +102,17 @@
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
-
-#
-# Loadable module support
-#
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
CONFIG_MODVERSIONS=y
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_KMOD=y
-
-#
-# Block layer
-#
CONFIG_BLOCK=y
CONFIG_LBD=y
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
+# CONFIG_BLK_DEV_BSG is not set
#
# IO Schedulers
@@ -153,7 +143,7 @@
CONFIG_MPC85xx=y
CONFIG_MPIC=y
# CONFIG_MPIC_WEIRD is not set
-# CONFIG_PPC_I8259 is not set
+CONFIG_PPC_I8259=y
# CONFIG_PPC_RTAS is not set
# CONFIG_MMIO_NVRAM is not set
# CONFIG_PPC_MPC106 is not set
@@ -191,6 +181,8 @@
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_RESOURCES_64BIT is not set
CONFIG_ZONE_DMA_FLAG=1
+CONFIG_BOUNCE=y
+CONFIG_VIRT_TO_BUS=y
CONFIG_PROC_DEVICETREE=y
CONFIG_CMDLINE_BOOL=y
CONFIG_CMDLINE="root=/dev/sda3 rw console=ttyS0,115200"
@@ -205,15 +197,21 @@
#
CONFIG_ZONE_DMA=y
CONFIG_PPC_INDIRECT_PCI=y
-CONFIG_PPC_INDIRECT_PCI_BE=y
CONFIG_FSL_SOC=y
-# CONFIG_PCI is not set
-# CONFIG_PCI_DOMAINS is not set
-# CONFIG_ARCH_SUPPORTS_MSI is not set
+CONFIG_FSL_PCI=y
+CONFIG_PCI=y
+CONFIG_PCI_DOMAINS=y
+CONFIG_PCI_SYSCALL=y
+# CONFIG_PCIEPORTBUS is not set
+CONFIG_ARCH_SUPPORTS_MSI=y
+# CONFIG_PCI_MSI is not set
+# CONFIG_PCI_DEBUG is not set
#
# PCCARD (PCMCIA/CardBus) support
#
+# CONFIG_PCCARD is not set
+# CONFIG_HOTPLUG_PCI is not set
#
# Advanced setup
@@ -254,7 +252,6 @@
CONFIG_IP_FIB_HASH=y
CONFIG_IP_MULTIPLE_TABLES=y
CONFIG_IP_ROUTE_MULTIPATH=y
-# CONFIG_IP_ROUTE_MULTIPATH_CACHED is not set
CONFIG_IP_ROUTE_VERBOSE=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
@@ -330,6 +327,7 @@
# CONFIG_MAC80211 is not set
# CONFIG_IEEE80211 is not set
# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
#
# Device Drivers
@@ -340,45 +338,35 @@
#
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
-
-#
-# Connector - unified userspace <-> kernelspace linker
-#
# CONFIG_CONNECTOR is not set
# CONFIG_MTD is not set
-
-#
-# Parallel port support
-#
# CONFIG_PARPORT is not set
-
-#
-# Plug and Play support
-#
-# CONFIG_PNPACPI is not set
-
-#
-# Block devices
-#
+CONFIG_BLK_DEV=y
# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_CPQ_DA is not set
+# CONFIG_BLK_CPQ_CISS_DA is not set
+# CONFIG_BLK_DEV_DAC960 is not set
+# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
# CONFIG_BLK_DEV_CRYPTOLOOP is not set
CONFIG_BLK_DEV_NBD=y
+# CONFIG_BLK_DEV_SX8 is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=2
CONFIG_BLK_DEV_RAM_SIZE=16384
CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
-
-#
-# Misc devices
-#
-# CONFIG_BLINK is not set
+CONFIG_MISC_DEVICES=y
+# CONFIG_PHANTOM is not set
+# CONFIG_EEPROM_93CX6 is not set
+# CONFIG_SGI_IOC4 is not set
+# CONFIG_TIFM_CORE is not set
# CONFIG_IDE is not set
#
@@ -386,6 +374,7 @@
#
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
+CONFIG_SCSI_DMA=y
# CONFIG_SCSI_TGT is not set
# CONFIG_SCSI_NETLINK is not set
CONFIG_SCSI_PROC_FS=y
@@ -422,25 +411,120 @@
# SCSI low-level drivers
#
# CONFIG_ISCSI_TCP is not set
+# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
+# CONFIG_SCSI_3W_9XXX is not set
+# CONFIG_SCSI_ACARD is not set
+# CONFIG_SCSI_AACRAID is not set
+# CONFIG_SCSI_AIC7XXX is not set
+# CONFIG_SCSI_AIC7XXX_OLD is not set
+# CONFIG_SCSI_AIC79XX is not set
+# CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_DPT_I2O is not set
+# CONFIG_SCSI_ARCMSR is not set
+# CONFIG_MEGARAID_NEWGEN is not set
+# CONFIG_MEGARAID_LEGACY is not set
+# CONFIG_MEGARAID_SAS is not set
+# CONFIG_SCSI_HPTIOP is not set
+# CONFIG_SCSI_BUSLOGIC is not set
+# CONFIG_SCSI_DMX3191D is not set
+# CONFIG_SCSI_EATA is not set
+# CONFIG_SCSI_FUTURE_DOMAIN is not set
+# CONFIG_SCSI_GDTH is not set
+# CONFIG_SCSI_IPS is not set
+# CONFIG_SCSI_INITIO is not set
+# CONFIG_SCSI_INIA100 is not set
+# CONFIG_SCSI_STEX is not set
+# CONFIG_SCSI_SYM53C8XX_2 is not set
+# CONFIG_SCSI_IPR is not set
+# CONFIG_SCSI_QLOGIC_1280 is not set
+# CONFIG_SCSI_QLA_FC is not set
+# CONFIG_SCSI_QLA_ISCSI is not set
+# CONFIG_SCSI_LPFC is not set
+# CONFIG_SCSI_DC395x is not set
+# CONFIG_SCSI_DC390T is not set
+# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_SRP is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
+# CONFIG_SATA_AHCI is not set
+# CONFIG_SATA_SVW is not set
+# CONFIG_ATA_PIIX is not set
+# CONFIG_SATA_MV is not set
+# CONFIG_SATA_NV is not set
+# CONFIG_PDC_ADMA is not set
+# CONFIG_SATA_QSTOR is not set
+# CONFIG_SATA_PROMISE is not set
+# CONFIG_SATA_SX4 is not set
+# CONFIG_SATA_SIL is not set
+# CONFIG_SATA_SIL24 is not set
+# CONFIG_SATA_SIS is not set
+# CONFIG_SATA_ULI is not set
+# CONFIG_SATA_VIA is not set
+# CONFIG_SATA_VITESSE is not set
+# CONFIG_SATA_INIC162X is not set
+# CONFIG_PATA_ALI is not set
+# CONFIG_PATA_AMD is not set
+# CONFIG_PATA_ARTOP is not set
+# CONFIG_PATA_ATIIXP is not set
+# CONFIG_PATA_CMD640_PCI is not set
+# CONFIG_PATA_CMD64X is not set
+# CONFIG_PATA_CS5520 is not set
+# CONFIG_PATA_CS5530 is not set
+# CONFIG_PATA_CYPRESS is not set
+# CONFIG_PATA_EFAR is not set
+# CONFIG_ATA_GENERIC is not set
+# CONFIG_PATA_HPT366 is not set
+# CONFIG_PATA_HPT37X is not set
+# CONFIG_PATA_HPT3X2N is not set
+# CONFIG_PATA_HPT3X3 is not set
+# CONFIG_PATA_IT821X is not set
+# CONFIG_PATA_IT8213 is not set
+# CONFIG_PATA_JMICRON is not set
+# CONFIG_PATA_TRIFLEX is not set
+# CONFIG_PATA_MARVELL is not set
+# CONFIG_PATA_MPIIX is not set
+# CONFIG_PATA_OLDPIIX is not set
+# CONFIG_PATA_NETCELL is not set
+# CONFIG_PATA_NS87410 is not set
+# CONFIG_PATA_OPTI is not set
+# CONFIG_PATA_OPTIDMA is not set
+# CONFIG_PATA_PDC_OLD is not set
+# CONFIG_PATA_RADISYS is not set
+# CONFIG_PATA_RZ1000 is not set
+# CONFIG_PATA_SC1200 is not set
+# CONFIG_PATA_SERVERWORKS is not set
+# CONFIG_PATA_PDC2027X is not set
+# CONFIG_PATA_SIL680 is not set
+# CONFIG_PATA_SIS is not set
+# CONFIG_PATA_VIA is not set
+# CONFIG_PATA_WINBOND is not set
# CONFIG_PATA_PLATFORM is not set
-
-#
-# Multi-device support (RAID and LVM)
-#
# CONFIG_MD is not set
-# CONFIG_MACINTOSH_DRIVERS is not set
#
-# Network device support
+# Fusion MPT device support
#
+# CONFIG_FUSION is not set
+# CONFIG_FUSION_SPI is not set
+# CONFIG_FUSION_FC is not set
+# CONFIG_FUSION_SAS is not set
+
+#
+# IEEE 1394 (FireWire) support
+#
+# CONFIG_FIREWIRE is not set
+# CONFIG_IEEE1394 is not set
+# CONFIG_I2O is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
CONFIG_NETDEVICES=y
+# CONFIG_NETDEVICES_MULTIQUEUE is not set
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
+# CONFIG_ARCNET is not set
CONFIG_PHYLIB=y
#
@@ -454,17 +538,44 @@
CONFIG_VITESSE_PHY=y
# CONFIG_SMSC_PHY is not set
# CONFIG_BROADCOM_PHY is not set
+# CONFIG_ICPLUS_PHY is not set
# CONFIG_FIXED_PHY is not set
-
-#
-# Ethernet (10 or 100Mbit)
-#
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
+# CONFIG_HAPPYMEAL is not set
+# CONFIG_SUNGEM is not set
+# CONFIG_CASSINI is not set
+# CONFIG_NET_VENDOR_3COM is not set
+# CONFIG_NET_TULIP is not set
+# CONFIG_HP100 is not set
+# CONFIG_NET_PCI is not set
CONFIG_NETDEV_1000=y
+# CONFIG_ACENIC is not set
+# CONFIG_DL2K is not set
+# CONFIG_E1000 is not set
+# CONFIG_NS83820 is not set
+# CONFIG_HAMACHI is not set
+# CONFIG_YELLOWFIN is not set
+# CONFIG_R8169 is not set
+# CONFIG_SIS190 is not set
+# CONFIG_SKGE is not set
+# CONFIG_SKY2 is not set
+# CONFIG_VIA_VELOCITY is not set
+# CONFIG_TIGON3 is not set
+# CONFIG_BNX2 is not set
CONFIG_GIANFAR=y
CONFIG_GFAR_NAPI=y
+# CONFIG_QLA3XXX is not set
+# CONFIG_ATL1 is not set
CONFIG_NETDEV_10000=y
+# CONFIG_CHELSIO_T1 is not set
+# CONFIG_CHELSIO_T3 is not set
+# CONFIG_IXGB is not set
+# CONFIG_S2IO is not set
+# CONFIG_MYRI10GE is not set
+# CONFIG_NETXEN_NIC is not set
+# CONFIG_MLX4_CORE is not set
+# CONFIG_TR is not set
#
# Wireless LAN
@@ -472,21 +583,16 @@
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
# CONFIG_WAN is not set
+# CONFIG_FDDI is not set
+# CONFIG_HIPPI is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
+# CONFIG_NET_FC is not set
# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
-
-#
-# ISDN subsystem
-#
# CONFIG_ISDN is not set
-
-#
-# Telephony Support
-#
# CONFIG_PHONE is not set
#
@@ -521,6 +627,7 @@
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
CONFIG_SERIO_SERPORT=y
+# CONFIG_SERIO_PCIPS2 is not set
CONFIG_SERIO_LIBPS2=y
# CONFIG_SERIO_RAW is not set
# CONFIG_GAMEPORT is not set
@@ -539,6 +646,7 @@
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_PCI=y
CONFIG_SERIAL_8250_NR_UARTS=4
CONFIG_SERIAL_8250_RUNTIME_UARTS=4
# CONFIG_SERIAL_8250_EXTENDED is not set
@@ -550,14 +658,11 @@
# CONFIG_SERIAL_UARTLITE is not set
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_JSM is not set
# CONFIG_SERIAL_OF_PLATFORM is not set
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
-
-#
-# IPMI
-#
# CONFIG_IPMI_HANDLER is not set
# CONFIG_WATCHDOG is not set
# CONFIG_HW_RANDOM is not set
@@ -565,12 +670,12 @@
CONFIG_GEN_RTC=y
CONFIG_GEN_RTC_X=y
# CONFIG_R3964 is not set
+# CONFIG_APPLICOM is not set
+# CONFIG_AGP is not set
+# CONFIG_DRM is not set
# CONFIG_RAW_DRIVER is not set
-
-#
-# TPM devices
-#
# CONFIG_TCG_TPM is not set
+CONFIG_DEVPORT=y
# CONFIG_I2C is not set
#
@@ -578,11 +683,8 @@
#
# CONFIG_SPI is not set
# CONFIG_SPI_MASTER is not set
-
-#
-# Dallas's 1-wire bus
-#
# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
#
@@ -655,19 +757,14 @@
# Sound
#
# CONFIG_SOUND is not set
-
-#
-# HID Devices
-#
+CONFIG_HID_SUPPORT=y
CONFIG_HID=y
# CONFIG_HID_DEBUG is not set
-
-#
-# USB support
-#
-# CONFIG_USB_ARCH_HAS_HCD is not set
-# CONFIG_USB_ARCH_HAS_OHCI is not set
-# CONFIG_USB_ARCH_HAS_EHCI is not set
+CONFIG_USB_SUPPORT=y
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+CONFIG_USB_ARCH_HAS_EHCI=y
+# CONFIG_USB is not set
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
@@ -691,14 +788,7 @@
#
# LED Triggers
#
-
-#
-# InfiniBand support
-#
-
-#
-# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
-#
+# CONFIG_INFINIBAND is not set
#
# Real Time Clock
@@ -719,19 +809,13 @@
# CONFIG_RTC_DRV_TEST is not set
#
-# I2C RTC drivers
-#
-
-#
-# SPI RTC drivers
-#
-
-#
# Platform RTC drivers
#
+# CONFIG_RTC_DRV_CMOS is not set
# CONFIG_RTC_DRV_DS1553 is not set
# CONFIG_RTC_DRV_DS1742 is not set
# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_M48T59 is not set
# CONFIG_RTC_DRV_V3020 is not set
#
@@ -752,6 +836,11 @@
#
#
+# Userspace I/O
+#
+# CONFIG_UIO is not set
+
+#
# File systems
#
CONFIG_EXT2_FS=y
@@ -859,7 +948,6 @@
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
-# CONFIG_9P_FS is not set
#
# Partition Types
@@ -941,6 +1029,7 @@
# CONFIG_CRC16 is not set
# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
CONFIG_LIBCRC32C=m
CONFIG_ZLIB_INFLATE=y
CONFIG_PLIST=y
@@ -965,6 +1054,7 @@
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
CONFIG_DETECT_SOFTLOCKUP=y
+CONFIG_SCHED_DEBUG=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_TIMER_STATS is not set
# CONFIG_DEBUG_SLAB is not set
@@ -996,10 +1086,6 @@
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
-
-#
-# Cryptographic options
-#
CONFIG_CRYPTO=y
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_BLKCIPHER=y
@@ -1038,7 +1124,4 @@
# CONFIG_CRYPTO_CRC32C is not set
# CONFIG_CRYPTO_CAMELLIA is not set
# CONFIG_CRYPTO_TEST is not set
-
-#
-# Hardware crypto devices
-#
+CONFIG_CRYPTO_HW=y
diff --git a/arch/powerpc/configs/mpc8568mds_defconfig b/arch/powerpc/configs/mpc8568mds_defconfig
index 6451d4d..417d3e6 100644
--- a/arch/powerpc/configs/mpc8568mds_defconfig
+++ b/arch/powerpc/configs/mpc8568mds_defconfig
@@ -1,9 +1,26 @@
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.22-rc7
-# Sun Jul 1 23:56:59 2007
+# Linux kernel version: 2.6.22
+# Fri Jul 20 13:55:04 2007
#
# CONFIG_PPC64 is not set
+
+#
+# Processor support
+#
+# CONFIG_6xx is not set
+CONFIG_PPC_85xx=y
+# CONFIG_PPC_8xx is not set
+# CONFIG_40x is not set
+# CONFIG_44x is not set
+# CONFIG_E200 is not set
+CONFIG_85xx=y
+CONFIG_E500=y
+CONFIG_BOOKE=y
+CONFIG_FSL_BOOKE=y
+# CONFIG_PHYS_64BIT is not set
+CONFIG_SPE=y
+# CONFIG_PPC_MM_SLICES is not set
CONFIG_PPC32=y
CONFIG_PPC_MERGE=y
CONFIG_MMU=y
@@ -14,6 +31,7 @@
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
+# CONFIG_ARCH_NO_VIRT_TO_BUS is not set
CONFIG_PPC=y
CONFIG_EARLY_PRINTK=y
CONFIG_GENERIC_NVRAM=y
@@ -25,28 +43,8 @@
CONFIG_AUDIT_ARCH=y
CONFIG_GENERIC_BUG=y
CONFIG_DEFAULT_UIMAGE=y
-
-#
-# Processor support
-#
-# CONFIG_CLASSIC32 is not set
-# CONFIG_PPC_82xx is not set
-# CONFIG_PPC_83xx is not set
-CONFIG_PPC_85xx=y
-# CONFIG_PPC_86xx is not set
-# CONFIG_PPC_8xx is not set
-# CONFIG_40x is not set
-# CONFIG_44x is not set
-# CONFIG_E200 is not set
-CONFIG_85xx=y
-CONFIG_E500=y
# CONFIG_PPC_DCR_NATIVE is not set
# CONFIG_PPC_DCR_MMIO is not set
-CONFIG_BOOKE=y
-CONFIG_FSL_BOOKE=y
-# CONFIG_PHYS_64BIT is not set
-CONFIG_SPE=y
-# CONFIG_PPC_MM_SLICES is not set
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
@@ -63,12 +61,11 @@
CONFIG_LOCALVERSION_AUTO=y
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
-# CONFIG_IPC_NS is not set
CONFIG_SYSVIPC_SYSCTL=y
# CONFIG_POSIX_MQUEUE is not set
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_TASKSTATS is not set
-# CONFIG_UTS_NS is not set
+# CONFIG_USER_NS is not set
# CONFIG_AUDIT is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=14
@@ -100,24 +97,17 @@
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
-
-#
-# Loadable module support
-#
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_MODULE_FORCE_UNLOAD is not set
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
# CONFIG_KMOD is not set
-
-#
-# Block layer
-#
CONFIG_BLOCK=y
# CONFIG_LBD is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
+# CONFIG_BLK_DEV_BSG is not set
#
# IO Schedulers
@@ -186,6 +176,8 @@
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_RESOURCES_64BIT is not set
CONFIG_ZONE_DMA_FLAG=1
+CONFIG_BOUNCE=y
+CONFIG_VIRT_TO_BUS=y
CONFIG_PROC_DEVICETREE=y
# CONFIG_CMDLINE_BOOL is not set
# CONFIG_PM is not set
@@ -201,14 +193,20 @@
CONFIG_PPC_INDIRECT_PCI=y
CONFIG_PPC_INDIRECT_PCI_BE=y
CONFIG_FSL_SOC=y
-# CONFIG_PCI is not set
-# CONFIG_PCI_DOMAINS is not set
-# CONFIG_ARCH_SUPPORTS_MSI is not set
+CONFIG_FSL_PCI=y
+CONFIG_PCI=y
+CONFIG_PCI_DOMAINS=y
+CONFIG_PCI_SYSCALL=y
+# CONFIG_PCIEPORTBUS is not set
+CONFIG_ARCH_SUPPORTS_MSI=y
+# CONFIG_PCI_MSI is not set
+# CONFIG_PCI_DEBUG is not set
#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set
+# CONFIG_HOTPLUG_PCI is not set
#
# Advanced setup
@@ -309,6 +307,7 @@
# CONFIG_MAC80211 is not set
# CONFIG_IEEE80211 is not set
# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
#
# Device Drivers
@@ -323,42 +322,31 @@
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
-
-#
-# Connector - unified userspace <-> kernelspace linker
-#
# CONFIG_CONNECTOR is not set
# CONFIG_MTD is not set
-
-#
-# Parallel port support
-#
# CONFIG_PARPORT is not set
-
-#
-# Plug and Play support
-#
-# CONFIG_PNPACPI is not set
-
-#
-# Block devices
-#
+CONFIG_BLK_DEV=y
# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_CPQ_DA is not set
+# CONFIG_BLK_CPQ_CISS_DA is not set
+# CONFIG_BLK_DEV_DAC960 is not set
+# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
# CONFIG_BLK_DEV_CRYPTOLOOP is not set
# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_SX8 is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=32768
CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
-
-#
-# Misc devices
-#
-# CONFIG_BLINK is not set
+CONFIG_MISC_DEVICES=y
+# CONFIG_PHANTOM is not set
+# CONFIG_EEPROM_93CX6 is not set
+# CONFIG_SGI_IOC4 is not set
+# CONFIG_TIFM_CORE is not set
# CONFIG_IDE is not set
#
@@ -366,6 +354,7 @@
#
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
+CONFIG_SCSI_DMA=y
# CONFIG_SCSI_TGT is not set
# CONFIG_SCSI_NETLINK is not set
CONFIG_SCSI_PROC_FS=y
@@ -402,23 +391,65 @@
# SCSI low-level drivers
#
# CONFIG_ISCSI_TCP is not set
+# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
+# CONFIG_SCSI_3W_9XXX is not set
+# CONFIG_SCSI_ACARD is not set
+# CONFIG_SCSI_AACRAID is not set
+# CONFIG_SCSI_AIC7XXX is not set
+# CONFIG_SCSI_AIC7XXX_OLD is not set
+# CONFIG_SCSI_AIC79XX is not set
+# CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_DPT_I2O is not set
+# CONFIG_SCSI_ARCMSR is not set
+# CONFIG_MEGARAID_NEWGEN is not set
+# CONFIG_MEGARAID_LEGACY is not set
+# CONFIG_MEGARAID_SAS is not set
+# CONFIG_SCSI_HPTIOP is not set
+# CONFIG_SCSI_BUSLOGIC is not set
+# CONFIG_SCSI_DMX3191D is not set
+# CONFIG_SCSI_EATA is not set
+# CONFIG_SCSI_FUTURE_DOMAIN is not set
+# CONFIG_SCSI_GDTH is not set
+# CONFIG_SCSI_IPS is not set
+# CONFIG_SCSI_INITIO is not set
+# CONFIG_SCSI_INIA100 is not set
+# CONFIG_SCSI_STEX is not set
+# CONFIG_SCSI_SYM53C8XX_2 is not set
+# CONFIG_SCSI_QLOGIC_1280 is not set
+# CONFIG_SCSI_QLA_FC is not set
+# CONFIG_SCSI_QLA_ISCSI is not set
+# CONFIG_SCSI_LPFC is not set
+# CONFIG_SCSI_DC395x is not set
+# CONFIG_SCSI_DC390T is not set
+# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_SRP is not set
# CONFIG_ATA is not set
-
-#
-# Multi-device support (RAID and LVM)
-#
# CONFIG_MD is not set
-# CONFIG_MACINTOSH_DRIVERS is not set
#
-# Network device support
+# Fusion MPT device support
#
+# CONFIG_FUSION is not set
+# CONFIG_FUSION_SPI is not set
+# CONFIG_FUSION_FC is not set
+# CONFIG_FUSION_SAS is not set
+
+#
+# IEEE 1394 (FireWire) support
+#
+# CONFIG_FIREWIRE is not set
+# CONFIG_IEEE1394 is not set
+# CONFIG_I2O is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
CONFIG_NETDEVICES=y
+# CONFIG_NETDEVICES_MULTIQUEUE is not set
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
+# CONFIG_ARCNET is not set
CONFIG_PHYLIB=y
#
@@ -432,17 +463,44 @@
# CONFIG_VITESSE_PHY is not set
# CONFIG_SMSC_PHY is not set
# CONFIG_BROADCOM_PHY is not set
+# CONFIG_ICPLUS_PHY is not set
# CONFIG_FIXED_PHY is not set
-
-#
-# Ethernet (10 or 100Mbit)
-#
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
+# CONFIG_HAPPYMEAL is not set
+# CONFIG_SUNGEM is not set
+# CONFIG_CASSINI is not set
+# CONFIG_NET_VENDOR_3COM is not set
+# CONFIG_NET_TULIP is not set
+# CONFIG_HP100 is not set
+# CONFIG_NET_PCI is not set
CONFIG_NETDEV_1000=y
+# CONFIG_ACENIC is not set
+# CONFIG_DL2K is not set
+# CONFIG_E1000 is not set
+# CONFIG_NS83820 is not set
+# CONFIG_HAMACHI is not set
+# CONFIG_YELLOWFIN is not set
+# CONFIG_R8169 is not set
+# CONFIG_SIS190 is not set
+# CONFIG_SKGE is not set
+# CONFIG_SKY2 is not set
+# CONFIG_VIA_VELOCITY is not set
+# CONFIG_TIGON3 is not set
+# CONFIG_BNX2 is not set
CONFIG_GIANFAR=y
CONFIG_GFAR_NAPI=y
+# CONFIG_QLA3XXX is not set
+# CONFIG_ATL1 is not set
CONFIG_NETDEV_10000=y
+# CONFIG_CHELSIO_T1 is not set
+# CONFIG_CHELSIO_T3 is not set
+# CONFIG_IXGB is not set
+# CONFIG_S2IO is not set
+# CONFIG_MYRI10GE is not set
+# CONFIG_NETXEN_NIC is not set
+# CONFIG_MLX4_CORE is not set
+# CONFIG_TR is not set
#
# Wireless LAN
@@ -450,21 +508,16 @@
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
# CONFIG_WAN is not set
+# CONFIG_FDDI is not set
+# CONFIG_HIPPI is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
+# CONFIG_NET_FC is not set
# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
-
-#
-# ISDN subsystem
-#
# CONFIG_ISDN is not set
-
-#
-# Telephony Support
-#
# CONFIG_PHONE is not set
#
@@ -510,6 +563,7 @@
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_PCI=y
CONFIG_SERIAL_8250_NR_UARTS=4
CONFIG_SERIAL_8250_RUNTIME_UARTS=4
# CONFIG_SERIAL_8250_EXTENDED is not set
@@ -521,14 +575,11 @@
# CONFIG_SERIAL_UARTLITE is not set
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_JSM is not set
# CONFIG_SERIAL_OF_PLATFORM is not set
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
-
-#
-# IPMI
-#
# CONFIG_IPMI_HANDLER is not set
CONFIG_WATCHDOG=y
# CONFIG_WATCHDOG_NOWAYOUT is not set
@@ -538,17 +589,23 @@
#
# CONFIG_SOFT_WATCHDOG is not set
# CONFIG_BOOKE_WDT is not set
+
+#
+# PCI-based Watchdog Cards
+#
+# CONFIG_PCIPCWATCHDOG is not set
+# CONFIG_WDTPCI is not set
CONFIG_HW_RANDOM=y
# CONFIG_NVRAM is not set
CONFIG_GEN_RTC=y
# CONFIG_GEN_RTC_X is not set
# CONFIG_R3964 is not set
+# CONFIG_APPLICOM is not set
+# CONFIG_AGP is not set
+# CONFIG_DRM is not set
# CONFIG_RAW_DRIVER is not set
-
-#
-# TPM devices
-#
# CONFIG_TCG_TPM is not set
+CONFIG_DEVPORT=y
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_CHARDEV=y
@@ -563,23 +620,43 @@
#
# I2C Hardware Bus support
#
+# CONFIG_I2C_ALI1535 is not set
+# CONFIG_I2C_ALI1563 is not set
+# CONFIG_I2C_ALI15X3 is not set
+# CONFIG_I2C_AMD756 is not set
+# CONFIG_I2C_AMD8111 is not set
+# CONFIG_I2C_I801 is not set
+# CONFIG_I2C_I810 is not set
+# CONFIG_I2C_PIIX4 is not set
CONFIG_I2C_MPC=y
+# CONFIG_I2C_NFORCE2 is not set
# CONFIG_I2C_OCORES is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_PROSAVAGE is not set
+# CONFIG_I2C_SAVAGE4 is not set
# CONFIG_I2C_SIMTEC is not set
+# CONFIG_I2C_SIS5595 is not set
+# CONFIG_I2C_SIS630 is not set
+# CONFIG_I2C_SIS96X is not set
+# CONFIG_I2C_TAOS_EVM is not set
# CONFIG_I2C_STUB is not set
+# CONFIG_I2C_VIA is not set
+# CONFIG_I2C_VIAPRO is not set
+# CONFIG_I2C_VOODOO3 is not set
#
# Miscellaneous I2C Chip support
#
# CONFIG_SENSORS_DS1337 is not set
# CONFIG_SENSORS_DS1374 is not set
+# CONFIG_DS1682 is not set
# CONFIG_SENSORS_EEPROM is not set
# CONFIG_SENSORS_PCF8574 is not set
# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_PCF8591 is not set
# CONFIG_SENSORS_M41T00 is not set
# CONFIG_SENSORS_MAX6875 is not set
+# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
@@ -590,11 +667,8 @@
#
# CONFIG_SPI is not set
# CONFIG_SPI_MASTER is not set
-
-#
-# Dallas's 1-wire bus
-#
# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
# CONFIG_SENSORS_ABITUGURU is not set
@@ -628,10 +702,13 @@
# CONFIG_SENSORS_MAX6650 is not set
# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_SIS5595 is not set
# CONFIG_SENSORS_SMSC47M1 is not set
# CONFIG_SENSORS_SMSC47M192 is not set
# CONFIG_SENSORS_SMSC47B397 is not set
+# CONFIG_SENSORS_VIA686A is not set
# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_SENSORS_VT8231 is not set
# CONFIG_SENSORS_W83781D is not set
# CONFIG_SENSORS_W83791D is not set
# CONFIG_SENSORS_W83792D is not set
@@ -670,19 +747,14 @@
# Sound
#
# CONFIG_SOUND is not set
-
-#
-# HID Devices
-#
+CONFIG_HID_SUPPORT=y
CONFIG_HID=y
# CONFIG_HID_DEBUG is not set
-
-#
-# USB support
-#
-# CONFIG_USB_ARCH_HAS_HCD is not set
-# CONFIG_USB_ARCH_HAS_OHCI is not set
-# CONFIG_USB_ARCH_HAS_EHCI is not set
+CONFIG_USB_SUPPORT=y
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+CONFIG_USB_ARCH_HAS_EHCI=y
+# CONFIG_USB is not set
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
@@ -706,14 +778,7 @@
#
# LED Triggers
#
-
-#
-# InfiniBand support
-#
-
-#
-# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
-#
+# CONFIG_INFINIBAND is not set
#
# Real Time Clock
@@ -734,6 +799,11 @@
#
#
+# Userspace I/O
+#
+# CONFIG_UIO is not set
+
+#
# File systems
#
CONFIG_EXT2_FS=y
@@ -829,7 +899,6 @@
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
-# CONFIG_9P_FS is not set
#
# Partition Types
@@ -868,6 +937,7 @@
# CONFIG_CRC16 is not set
# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
# CONFIG_LIBCRC32C is not set
CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
@@ -892,6 +962,7 @@
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
CONFIG_DETECT_SOFTLOCKUP=y
+CONFIG_SCHED_DEBUG=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_TIMER_STATS is not set
# CONFIG_DEBUG_SLAB is not set
@@ -915,7 +986,7 @@
CONFIG_DEBUGGER=y
# CONFIG_XMON is not set
# CONFIG_BDI_SWITCH is not set
-CONFIG_BOOTX_TEXT=y
+# CONFIG_BOOTX_TEXT is not set
CONFIG_PPC_EARLY_DEBUG=y
# CONFIG_PPC_EARLY_DEBUG_LPAR is not set
# CONFIG_PPC_EARLY_DEBUG_G5 is not set
@@ -932,10 +1003,6 @@
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
-
-#
-# Cryptographic options
-#
CONFIG_CRYPTO=y
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_BLKCIPHER=y
@@ -973,7 +1040,4 @@
# CONFIG_CRYPTO_CRC32C is not set
# CONFIG_CRYPTO_CAMELLIA is not set
# CONFIG_CRYPTO_TEST is not set
-
-#
-# Hardware crypto devices
-#
+CONFIG_CRYPTO_HW=y
diff --git a/arch/powerpc/kernel/pci_32.c b/arch/powerpc/kernel/pci_32.c
index 0adf077..721a694 100644
--- a/arch/powerpc/kernel/pci_32.c
+++ b/arch/powerpc/kernel/pci_32.c
@@ -415,15 +415,13 @@
return 0;
}
-static void __init
-update_bridge_base(struct pci_bus *bus, int i)
+void __init
+update_bridge_resource(struct pci_dev *dev, struct resource *res)
{
- struct resource *res = bus->resource[i];
u8 io_base_lo, io_limit_lo;
u16 mem_base, mem_limit;
u16 cmd;
unsigned long start, end, off;
- struct pci_dev *dev = bus->self;
struct pci_controller *hose = dev->sysdata;
if (!hose) {
@@ -467,12 +465,20 @@
pci_write_config_word(dev, PCI_PREF_MEMORY_LIMIT, mem_limit);
} else {
- DBG(KERN_ERR "PCI: ugh, bridge %s res %d has flags=%lx\n",
- pci_name(dev), i, res->flags);
+ DBG(KERN_ERR "PCI: ugh, bridge %s res has flags=%lx\n",
+ pci_name(dev), res->flags);
}
pci_write_config_word(dev, PCI_COMMAND, cmd);
}
+static void __init
+update_bridge_base(struct pci_bus *bus, int i)
+{
+ struct resource *res = bus->resource[i];
+ struct pci_dev *dev = bus->self;
+ update_bridge_resource(dev, res);
+}
+
static inline void alloc_resource(struct pci_dev *dev, int idx)
{
struct resource *pr, *r = &dev->resource[idx];
@@ -1468,3 +1474,10 @@
EARLY_PCI_OP(write, byte, u8)
EARLY_PCI_OP(write, word, u16)
EARLY_PCI_OP(write, dword, u32)
+
+extern int pci_bus_find_capability (struct pci_bus *bus, unsigned int devfn, int cap);
+int early_find_capability(struct pci_controller *hose, int bus, int devfn,
+ int cap)
+{
+ return pci_bus_find_capability(fake_pci_bus(hose, bus), devfn, cap);
+}
diff --git a/arch/powerpc/platforms/82xx/mpc82xx_ads.c b/arch/powerpc/platforms/82xx/mpc82xx_ads.c
index da20832..2d1b05b 100644
--- a/arch/powerpc/platforms/82xx/mpc82xx_ads.c
+++ b/arch/powerpc/platforms/82xx/mpc82xx_ads.c
@@ -553,7 +553,8 @@
setup_indirect_pci(hose,
r.start + offsetof(pci_cpm2_t, pci_cfg_addr),
- r.start + offsetof(pci_cpm2_t, pci_cfg_data));
+ r.start + offsetof(pci_cpm2_t, pci_cfg_data),
+ 0);
pci_process_bridge_OF_ranges(hose, np, 1);
}
diff --git a/arch/powerpc/platforms/83xx/pci.c b/arch/powerpc/platforms/83xx/pci.c
index c0e2b89..9206946 100644
--- a/arch/powerpc/platforms/83xx/pci.c
+++ b/arch/powerpc/platforms/83xx/pci.c
@@ -74,11 +74,11 @@
*/
/* PCI 1 */
if ((rsrc.start & 0xfffff) == 0x8500) {
- setup_indirect_pci(hose, immr + 0x8300, immr + 0x8304);
+ setup_indirect_pci(hose, immr + 0x8300, immr + 0x8304, 0);
}
/* PCI 2 */
if ((rsrc.start & 0xfffff) == 0x8600) {
- setup_indirect_pci(hose, immr + 0x8380, immr + 0x8384);
+ setup_indirect_pci(hose, immr + 0x8380, immr + 0x8384, 0);
primary = 0;
}
diff --git a/arch/powerpc/platforms/85xx/Kconfig b/arch/powerpc/platforms/85xx/Kconfig
index 629926e..f581840 100644
--- a/arch/powerpc/platforms/85xx/Kconfig
+++ b/arch/powerpc/platforms/85xx/Kconfig
@@ -18,6 +18,7 @@
config MPC85xx_CDS
bool "Freescale MPC85xx CDS"
select DEFAULT_UIMAGE
+ select PPC_I8259
help
This option enables support for the MPC85xx CDS board
@@ -30,6 +31,7 @@
config MPC8544_DS
bool "Freescale MPC8544 DS"
+ select PPC_I8259
select DEFAULT_UIMAGE
help
This option enables support for the MPC8544 DS board
@@ -50,9 +52,9 @@
config MPC85xx
bool
select PPC_UDBG_16550
- select PPC_INDIRECT_PCI
- select PPC_INDIRECT_PCI_BE
+ select PPC_INDIRECT_PCI if PCI
select MPIC
+ select FSL_PCI if PCI
select SERIAL_8250_SHARE_IRQ if SERIAL_8250
default y if MPC8540_ADS || MPC85xx_CDS || MPC8560_ADS \
|| MPC85xx_MDS || MPC8544_DS
diff --git a/arch/powerpc/platforms/85xx/Makefile b/arch/powerpc/platforms/85xx/Makefile
index 4e02cbb..d70f2d0 100644
--- a/arch/powerpc/platforms/85xx/Makefile
+++ b/arch/powerpc/platforms/85xx/Makefile
@@ -1,7 +1,7 @@
#
# Makefile for the PowerPC 85xx linux kernel.
#
-obj-$(CONFIG_PPC_85xx) += misc.o pci.o
+obj-$(CONFIG_PPC_85xx) += misc.o
obj-$(CONFIG_MPC8540_ADS) += mpc85xx_ads.o
obj-$(CONFIG_MPC8560_ADS) += mpc85xx_ads.o
obj-$(CONFIG_MPC85xx_CDS) += mpc85xx_cds.o
diff --git a/arch/powerpc/platforms/85xx/mpc8544_ds.c b/arch/powerpc/platforms/85xx/mpc8544_ds.c
index 6fb90aa..4905f6f 100644
--- a/arch/powerpc/platforms/85xx/mpc8544_ds.c
+++ b/arch/powerpc/platforms/85xx/mpc8544_ds.c
@@ -2,6 +2,8 @@
* MPC8544 DS Board Setup
*
* Author Xianghua Xiao (x.xiao@freescale.com)
+ * Roy Zang <tie-fei.zang@freescale.com>
+ * - Add PCI/PCI Exprees support
* Copyright 2007 Freescale Semiconductor Inc.
*
* This program is free software; you can redistribute it and/or modify it
@@ -12,13 +14,16 @@
#include <linux/stddef.h>
#include <linux/kernel.h>
+#include <linux/pci.h>
#include <linux/kdev_t.h>
#include <linux/delay.h>
#include <linux/seq_file.h>
+#include <linux/interrupt.h>
#include <asm/system.h>
#include <asm/time.h>
#include <asm/machdep.h>
+#include <asm/pci-bridge.h>
#include <asm/mpc85xx.h>
#include <mm/mmu_decl.h>
#include <asm/prom.h>
@@ -27,6 +32,7 @@
#include <asm/i8259.h>
#include <sysdev/fsl_soc.h>
+#include <sysdev/fsl_pci.h>
#include "mpc85xx.h"
#undef DEBUG
@@ -37,6 +43,17 @@
#define DBG(fmt, args...)
#endif
+#ifdef CONFIG_PPC_I8259
+static void mpc8544_8259_cascade(unsigned int irq, struct irq_desc *desc)
+{
+ unsigned int cascade_irq = i8259_irq();
+
+ if (cascade_irq != NO_IRQ) {
+ generic_handle_irq(cascade_irq);
+ }
+ desc->chip->eoi(irq);
+}
+#endif /* CONFIG_PPC_I8259 */
void __init mpc8544_ds_pic_init(void)
{
@@ -96,19 +113,240 @@
#endif /* CONFIG_PPC_I8259 */
}
+#ifdef CONFIG_PCI
+enum pirq { PIRQA = 8, PIRQB, PIRQC, PIRQD, PIRQE, PIRQF, PIRQG, PIRQH };
+
+/*
+ * Value in table -- IRQ number
+ */
+const unsigned char uli1575_irq_route_table[16] = {
+ 0, /* 0: Reserved */
+ 0x8,
+ 0, /* 2: Reserved */
+ 0x2,
+ 0x4,
+ 0x5,
+ 0x7,
+ 0x6,
+ 0, /* 8: Reserved */
+ 0x1,
+ 0x3,
+ 0x9,
+ 0xb,
+ 0, /* 13: Reserved */
+ 0xd,
+ 0xf,
+};
+
+static int __devinit
+get_pci_irq_from_of(struct pci_controller *hose, int slot, int pin)
+{
+ struct of_irq oirq;
+ u32 laddr[3];
+ struct device_node *hosenode = hose ? hose->arch_data : NULL;
+
+ if (!hosenode)
+ return -EINVAL;
+
+ laddr[0] = (hose->first_busno << 16) | (PCI_DEVFN(slot, 0) << 8);
+ laddr[1] = laddr[2] = 0;
+ of_irq_map_raw(hosenode, &pin, 1, laddr, &oirq);
+ DBG("mpc8544_ds: pci irq addr %x, slot %d, pin %d, irq %d\n",
+ laddr[0], slot, pin, oirq.specifier[0]);
+ return oirq.specifier[0];
+}
+
+/*8259*/
+static void __devinit quirk_uli1575(struct pci_dev *dev)
+{
+ unsigned short temp;
+ struct pci_controller *hose = pci_bus_to_host(dev->bus);
+ unsigned char irq2pin[16];
+ unsigned long pirq_map_word = 0;
+ u32 irq;
+ int i;
+
+ /*
+ * ULI1575 interrupts route setup
+ */
+ memset(irq2pin, 0, 16); /* Initialize default value 0 */
+
+ irq2pin[6]=PIRQA+3; /* enabled mapping for IRQ6 to PIRQD, used by SATA */
+
+ /*
+ * PIRQE -> PIRQF mapping set manually
+ *
+ * IRQ pin IRQ#
+ * PIRQE ---- 9
+ * PIRQF ---- 10
+ * PIRQG ---- 11
+ * PIRQH ---- 12
+ */
+ for (i = 0; i < 4; i++)
+ irq2pin[i + 9] = PIRQE + i;
+
+ /* Set IRQ-PIRQ Mapping to ULI1575 */
+ for (i = 0; i < 16; i++)
+ if (irq2pin[i])
+ pirq_map_word |= (uli1575_irq_route_table[i] & 0xf)
+ << ((irq2pin[i] - PIRQA) * 4);
+
+ pirq_map_word |= 1<<26; /* disable INTx in EP mode*/
+
+ /* ULI1575 IRQ mapping conf register default value is 0xb9317542 */
+ DBG("Setup ULI1575 IRQ mapping configuration register value = 0x%x\n",
+ (int)pirq_map_word);
+ pci_write_config_dword(dev, 0x48, pirq_map_word);
+
+#define ULI1575_SET_DEV_IRQ(slot, pin, reg) \
+ do { \
+ int irq; \
+ irq = get_pci_irq_from_of(hose, slot, pin); \
+ if (irq > 0 && irq < 16) \
+ pci_write_config_byte(dev, reg, irq2pin[irq]); \
+ else \
+ printk(KERN_WARNING "ULI1575 device" \
+ "(slot %d, pin %d) irq %d is invalid.\n", \
+ slot, pin, irq); \
+ } while(0)
+
+ /* USB 1.1 OHCI controller 1, slot 28, pin 1 */
+ ULI1575_SET_DEV_IRQ(28, 1, 0x86);
+
+ /* USB 1.1 OHCI controller 2, slot 28, pin 2 */
+ ULI1575_SET_DEV_IRQ(28, 2, 0x87);
+
+ /* USB 1.1 OHCI controller 3, slot 28, pin 3 */
+ ULI1575_SET_DEV_IRQ(28, 3, 0x88);
+
+ /* USB 2.0 controller, slot 28, pin 4 */
+ irq = get_pci_irq_from_of(hose, 28, 4);
+ if (irq >= 0 && irq <= 15)
+ pci_write_config_dword(dev, 0x74, uli1575_irq_route_table[irq]);
+
+ /* Audio controller, slot 29, pin 1 */
+ ULI1575_SET_DEV_IRQ(29, 1, 0x8a);
+
+ /* Modem controller, slot 29, pin 2 */
+ ULI1575_SET_DEV_IRQ(29, 2, 0x8b);
+
+ /* HD audio controller, slot 29, pin 3 */
+ ULI1575_SET_DEV_IRQ(29, 3, 0x8c);
+
+ /* SMB interrupt: slot 30, pin 1 */
+ ULI1575_SET_DEV_IRQ(30, 1, 0x8e);
+
+ /* PMU ACPI SCI interrupt: slot 30, pin 2 */
+ ULI1575_SET_DEV_IRQ(30, 2, 0x8f);
+
+ /* Serial ATA interrupt: slot 31, pin 1 */
+ ULI1575_SET_DEV_IRQ(31, 1, 0x8d);
+
+ /* Primary PATA IDE IRQ: 14
+ * Secondary PATA IDE IRQ: 15
+ */
+ pci_write_config_byte(dev, 0x44, 0x30 | uli1575_irq_route_table[14]);
+ pci_write_config_byte(dev, 0x75, uli1575_irq_route_table[15]);
+
+ /* Set IRQ14 and IRQ15 to legacy IRQs */
+ pci_read_config_word(dev, 0x46, &temp);
+ temp |= 0xc000;
+ pci_write_config_word(dev, 0x46, temp);
+
+ /* Set i8259 interrupt trigger
+ * IRQ 3: Level
+ * IRQ 4: Level
+ * IRQ 5: Level
+ * IRQ 6: Level
+ * IRQ 7: Level
+ * IRQ 9: Level
+ * IRQ 10: Level
+ * IRQ 11: Level
+ * IRQ 12: Level
+ * IRQ 14: Edge
+ * IRQ 15: Edge
+ */
+ outb(0xfa, 0x4d0);
+ outb(0x1e, 0x4d1);
+
+#undef ULI1575_SET_DEV_IRQ
+}
+
+/* SATA */
+static void __devinit quirk_uli5288(struct pci_dev *dev)
+{
+ unsigned char c;
+
+ pci_read_config_byte(dev, 0x83, &c);
+ c |= 0x80; /* read/write lock */
+ pci_write_config_byte(dev, 0x83, c);
+
+ pci_write_config_byte(dev, 0x09, 0x01); /* Base class code: storage */
+ pci_write_config_byte(dev, 0x0a, 0x06); /* IDE disk */
+
+ pci_read_config_byte(dev, 0x83, &c);
+ c &= 0x7f;
+ pci_write_config_byte(dev, 0x83, c);
+
+ pci_read_config_byte(dev, 0x84, &c);
+ c |= 0x01; /* emulated PATA mode enabled */
+ pci_write_config_byte(dev, 0x84, c);
+}
+
+/* PATA */
+static void __devinit quirk_uli5229(struct pci_dev *dev)
+{
+ unsigned short temp;
+ pci_write_config_word(dev, 0x04, 0x0405); /* MEM IO MSI */
+ pci_read_config_word(dev, 0x4a, &temp);
+ temp |= 0x1000; /* Enable Native IRQ 14/15 */
+ pci_write_config_word(dev, 0x4a, temp);
+}
+
+/*Bridge*/
+static void __devinit early_uli5249(struct pci_dev *dev)
+{
+ unsigned char temp;
+ pci_write_config_word(dev, 0x04, 0x0007); /* mem access */
+ pci_read_config_byte(dev, 0x7c, &temp);
+ pci_write_config_byte(dev, 0x7c, 0x80); /* R/W lock control */
+ pci_write_config_byte(dev, 0x09, 0x01); /* set as pci-pci bridge */
+ pci_write_config_byte(dev, 0x7c, temp); /* restore pci bus debug control */
+ dev->class |= 0x1;
+}
+
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x1575, quirk_uli1575);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x5288, quirk_uli5288);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x5229, quirk_uli5229);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_AL, 0x5249, early_uli5249);
+#endif /* CONFIG_PCI */
/*
* Setup the architecture
*/
static void __init mpc8544_ds_setup_arch(void)
{
+#ifdef CONFIG_PCI
+ struct device_node *np;
+#endif
+
if (ppc_md.progress)
ppc_md.progress("mpc8544_ds_setup_arch()", 0);
+#ifdef CONFIG_PCI
+ for (np = NULL; (np = of_find_node_by_type(np, "pci")) != NULL;) {
+ struct resource rsrc;
+ of_address_to_resource(np, 0, &rsrc);
+ if ((rsrc.start & 0xfffff) == 0xb000)
+ fsl_add_bridge(np, 1);
+ else
+ fsl_add_bridge(np, 0);
+ }
+#endif
+
printk("MPC8544 DS board from Freescale Semiconductor\n");
}
-
/*
* Called very early, device-tree isn't unflattened
*/
@@ -124,6 +362,7 @@
.probe = mpc8544_ds_probe,
.setup_arch = mpc8544_ds_setup_arch,
.init_IRQ = mpc8544_ds_pic_init,
+ .pcibios_fixup_bus = fsl_pcibios_fixup_bus,
.get_irq = mpic_get_irq,
.restart = mpc85xx_restart,
.calibrate_decr = generic_calibrate_decr,
diff --git a/arch/powerpc/platforms/85xx/mpc85xx.h b/arch/powerpc/platforms/85xx/mpc85xx.h
index 7286ffa..5b34dee 100644
--- a/arch/powerpc/platforms/85xx/mpc85xx.h
+++ b/arch/powerpc/platforms/85xx/mpc85xx.h
@@ -15,4 +15,3 @@
*/
extern void mpc85xx_restart(char *);
-extern int mpc85xx_add_bridge(struct device_node *dev);
diff --git a/arch/powerpc/platforms/85xx/mpc85xx_ads.c b/arch/powerpc/platforms/85xx/mpc85xx_ads.c
index 7235f70..40a8286 100644
--- a/arch/powerpc/platforms/85xx/mpc85xx_ads.c
+++ b/arch/powerpc/platforms/85xx/mpc85xx_ads.c
@@ -29,6 +29,7 @@
#include <asm/udbg.h>
#include <sysdev/fsl_soc.h>
+#include <sysdev/fsl_pci.h>
#include "mpc85xx.h"
#ifdef CONFIG_CPM2
@@ -217,7 +218,7 @@
#ifdef CONFIG_PCI
for (np = NULL; (np = of_find_node_by_type(np, "pci")) != NULL;)
- mpc85xx_add_bridge(np);
+ fsl_add_bridge(np, 1);
ppc_md.pci_exclude_device = mpc85xx_exclude_device;
#endif
}
diff --git a/arch/powerpc/platforms/85xx/mpc85xx_cds.c b/arch/powerpc/platforms/85xx/mpc85xx_cds.c
index 50c8d64..6a171e9 100644
--- a/arch/powerpc/platforms/85xx/mpc85xx_cds.c
+++ b/arch/powerpc/platforms/85xx/mpc85xx_cds.c
@@ -24,6 +24,7 @@
#include <linux/seq_file.h>
#include <linux/initrd.h>
#include <linux/module.h>
+#include <linux/interrupt.h>
#include <linux/fsl_devices.h>
#include <asm/system.h>
@@ -45,6 +46,7 @@
#include <asm/i8259.h>
#include <sysdev/fsl_soc.h>
+#include <sysdev/fsl_pci.h>
#include "mpc85xx.h"
static int cds_pci_slot = 2;
@@ -58,8 +60,6 @@
static int mpc85xx_exclude_device(struct pci_controller *hose,
u_char bus, u_char devfn)
{
- if ((bus == hose->first_busno) && PCI_SLOT(devfn) == 0)
- return PCIBIOS_DEVICE_NOT_FOUND;
/* We explicitly do not go past the Tundra 320 Bridge */
if ((bus == 1) && (PCI_SLOT(devfn) == ARCADIA_2ND_BRIDGE_IDSEL))
return PCIBIOS_DEVICE_NOT_FOUND;
@@ -69,6 +69,37 @@
return PCIBIOS_SUCCESSFUL;
}
+static void mpc85xx_cds_restart(char *cmd)
+{
+ struct pci_dev *dev;
+ u_char tmp;
+
+ if ((dev = pci_get_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686,
+ NULL))) {
+
+ /* Use the VIA Super Southbridge to force a PCI reset */
+ pci_read_config_byte(dev, 0x47, &tmp);
+ pci_write_config_byte(dev, 0x47, tmp | 1);
+
+ /* Flush the outbound PCI write queues */
+ pci_read_config_byte(dev, 0x47, &tmp);
+
+ /*
+ * At this point, the harware reset should have triggered.
+ * However, if it doesn't work for some mysterious reason,
+ * just fall through to the default reset below.
+ */
+
+ pci_dev_put(dev);
+ }
+
+ /*
+ * If we can't find the VIA chip (maybe the P2P bridge is disabled)
+ * or the VIA chip reset didn't work, just use the default reset.
+ */
+ mpc85xx_restart(NULL);
+}
+
static void __init mpc85xx_cds_pci_irq_fixup(struct pci_dev *dev)
{
u_char c;
@@ -98,7 +129,7 @@
/* There are two USB controllers.
* Identify them by functon number
*/
- if (PCI_FUNC(dev->devfn))
+ if (PCI_FUNC(dev->devfn) == 3)
dev->irq = 11;
else
dev->irq = 10;
@@ -109,17 +140,41 @@
}
}
+static void __devinit skip_fake_bridge(struct pci_dev *dev)
+{
+ /* Make it an error to skip the fake bridge
+ * in pci_setup_device() in probe.c */
+ dev->hdr_type = 0x7f;
+}
+DECLARE_PCI_FIXUP_EARLY(0x1957, 0x3fff, skip_fake_bridge);
+DECLARE_PCI_FIXUP_EARLY(0x3fff, 0x1957, skip_fake_bridge);
+DECLARE_PCI_FIXUP_EARLY(0xff3f, 0x5719, skip_fake_bridge);
+
#ifdef CONFIG_PPC_I8259
-#warning The i8259 PIC support is currently broken
-static void mpc85xx_8259_cascade(unsigned int irq, struct irq_desc *desc)
+static void mpc85xx_8259_cascade_handler(unsigned int irq,
+ struct irq_desc *desc)
{
unsigned int cascade_irq = i8259_irq();
if (cascade_irq != NO_IRQ)
+ /* handle an interrupt from the 8259 */
generic_handle_irq(cascade_irq);
- desc->chip->eoi(irq);
+ /* check for any interrupts from the shared IRQ line */
+ handle_fasteoi_irq(irq, desc);
}
+
+static irqreturn_t mpc85xx_8259_cascade_action(int irq, void *dev_id)
+{
+ return IRQ_HANDLED;
+}
+
+static struct irqaction mpc85xxcds_8259_irqaction = {
+ .handler = mpc85xx_8259_cascade_action,
+ .flags = IRQF_SHARED,
+ .mask = CPU_MASK_NONE,
+ .name = "8259 cascade",
+};
#endif /* PPC_I8259 */
#endif /* CONFIG_PCI */
@@ -128,10 +183,6 @@
struct mpic *mpic;
struct resource r;
struct device_node *np = NULL;
-#ifdef CONFIG_PPC_I8259
- struct device_node *cascade_node = NULL;
- int cascade_irq;
-#endif
np = of_find_node_by_type(np, "open-pic");
@@ -155,8 +206,19 @@
of_node_put(np);
mpic_init(mpic);
+}
-#ifdef CONFIG_PPC_I8259
+#if defined(CONFIG_PPC_I8259) && defined(CONFIG_PCI)
+static int mpc85xx_cds_8259_attach(void)
+{
+ int ret;
+ struct device_node *np = NULL;
+ struct device_node *cascade_node = NULL;
+ int cascade_irq;
+
+ if (!machine_is(mpc85xx_cds))
+ return 0;
+
/* Initialize the i8259 controller */
for_each_node_by_type(np, "interrupt-controller")
if (of_device_is_compatible(np, "chrp,iic")) {
@@ -166,22 +228,39 @@
if (cascade_node == NULL) {
printk(KERN_DEBUG "Could not find i8259 PIC\n");
- return;
+ return -ENODEV;
}
cascade_irq = irq_of_parse_and_map(cascade_node, 0);
if (cascade_irq == NO_IRQ) {
printk(KERN_ERR "Failed to map cascade interrupt\n");
- return;
+ return -ENXIO;
}
i8259_init(cascade_node, 0);
of_node_put(cascade_node);
- set_irq_chained_handler(cascade_irq, mpc85xx_8259_cascade);
-#endif /* CONFIG_PPC_I8259 */
+ /*
+ * Hook the interrupt to make sure desc->action is never NULL.
+ * This is required to ensure that the interrupt does not get
+ * disabled when the last user of the shared IRQ line frees their
+ * interrupt.
+ */
+ if ((ret = setup_irq(cascade_irq, &mpc85xxcds_8259_irqaction))) {
+ printk(KERN_ERR "Failed to setup cascade interrupt\n");
+ return ret;
+ }
+
+ /* Success. Connect our low-level cascade handler. */
+ set_irq_handler(cascade_irq, mpc85xx_8259_cascade_handler);
+
+ return 0;
}
+device_initcall(mpc85xx_cds_8259_attach);
+
+#endif /* CONFIG_PPC_I8259 */
+
/*
* Setup the architecture
*/
@@ -218,9 +297,14 @@
}
#ifdef CONFIG_PCI
- for (np = NULL; (np = of_find_node_by_type(np, "pci")) != NULL;)
- mpc85xx_add_bridge(np);
-
+ for (np = NULL; (np = of_find_node_by_type(np, "pci")) != NULL;) {
+ struct resource rsrc;
+ of_address_to_resource(np, 0, &rsrc);
+ if ((rsrc.start & 0xfffff) == 0x8000)
+ fsl_add_bridge(np, 1);
+ else
+ fsl_add_bridge(np, 0);
+ }
ppc_md.pci_irq_fixup = mpc85xx_cds_pci_irq_fixup;
ppc_md.pci_exclude_device = mpc85xx_exclude_device;
#endif
@@ -265,7 +349,12 @@
.init_IRQ = mpc85xx_cds_pic_init,
.show_cpuinfo = mpc85xx_cds_show_cpuinfo,
.get_irq = mpic_get_irq,
+#ifdef CONFIG_PCI
+ .restart = mpc85xx_cds_restart,
+#else
.restart = mpc85xx_restart,
+#endif
.calibrate_decr = generic_calibrate_decr,
.progress = udbg_progress,
+ .pcibios_fixup_bus = fsl_pcibios_fixup_bus,
};
diff --git a/arch/powerpc/platforms/85xx/mpc85xx_mds.c b/arch/powerpc/platforms/85xx/mpc85xx_mds.c
index 004b80b..e8003bf 100644
--- a/arch/powerpc/platforms/85xx/mpc85xx_mds.c
+++ b/arch/powerpc/platforms/85xx/mpc85xx_mds.c
@@ -46,6 +46,7 @@
#include <asm/prom.h>
#include <asm/udbg.h>
#include <sysdev/fsl_soc.h>
+#include <sysdev/fsl_pci.h>
#include <asm/qe.h>
#include <asm/qe_ic.h>
#include <asm/mpic.h>
@@ -94,9 +95,8 @@
}
#ifdef CONFIG_PCI
- for (np = NULL; (np = of_find_node_by_type(np, "pci")) != NULL;) {
- mpc85xx_add_bridge(np);
- }
+ for (np = NULL; (np = of_find_node_by_type(np, "pci")) != NULL;)
+ fsl_add_bridge(np, 1);
of_node_put(np);
#endif
@@ -208,4 +208,5 @@
.restart = mpc85xx_restart,
.calibrate_decr = generic_calibrate_decr,
.progress = udbg_progress,
+ .pcibios_fixup_bus = fsl_pcibios_fixup_bus,
};
diff --git a/arch/powerpc/platforms/85xx/pci.c b/arch/powerpc/platforms/85xx/pci.c
deleted file mode 100644
index 8118417..0000000
--- a/arch/powerpc/platforms/85xx/pci.c
+++ /dev/null
@@ -1,91 +0,0 @@
-/*
- * FSL SoC setup code
- *
- * Maintained by Kumar Gala (see MAINTAINERS for contact information)
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-#include <linux/stddef.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/errno.h>
-#include <linux/pci.h>
-#include <linux/delay.h>
-#include <linux/irq.h>
-#include <linux/module.h>
-
-#include <asm/system.h>
-#include <asm/atomic.h>
-#include <asm/io.h>
-#include <asm/pci-bridge.h>
-#include <asm/prom.h>
-#include <sysdev/fsl_soc.h>
-
-#undef DEBUG
-
-#ifdef DEBUG
-#define DBG(x...) printk(x)
-#else
-#define DBG(x...)
-#endif
-
-#ifdef CONFIG_PCI
-int __init mpc85xx_add_bridge(struct device_node *dev)
-{
- int len;
- struct pci_controller *hose;
- struct resource rsrc;
- const int *bus_range;
- int primary = 1, has_address = 0;
- phys_addr_t immr = get_immrbase();
-
- DBG("Adding PCI host bridge %s\n", dev->full_name);
-
- /* Fetch host bridge registers address */
- has_address = (of_address_to_resource(dev, 0, &rsrc) == 0);
-
- /* Get bus range if any */
- bus_range = of_get_property(dev, "bus-range", &len);
- if (bus_range == NULL || len < 2 * sizeof(int)) {
- printk(KERN_WARNING "Can't get bus-range for %s, assume"
- " bus 0\n", dev->full_name);
- }
-
- pci_assign_all_buses = 1;
- hose = pcibios_alloc_controller(dev);
- if (!hose)
- return -ENOMEM;
-
- hose->first_busno = bus_range ? bus_range[0] : 0;
- hose->last_busno = bus_range ? bus_range[1] : 0xff;
-
- /* PCI 1 */
- if ((rsrc.start & 0xfffff) == 0x8000) {
- setup_indirect_pci(hose, immr + 0x8000, immr + 0x8004);
- }
- /* PCI 2 */
- if ((rsrc.start & 0xfffff) == 0x9000) {
- setup_indirect_pci(hose, immr + 0x9000, immr + 0x9004);
- primary = 0;
- }
-
- printk(KERN_INFO "Found MPC85xx PCI host bridge at 0x%016llx. "
- "Firmware bus number: %d->%d\n",
- (unsigned long long)rsrc.start, hose->first_busno,
- hose->last_busno);
-
- DBG(" ->Hose at 0x%p, cfg_addr=0x%p,cfg_data=0x%p\n",
- hose, hose->cfg_addr, hose->cfg_data);
-
- /* Interpret the "ranges" property */
- /* This also maps the I/O region and sets isa_io/mem_base */
- pci_process_bridge_OF_ranges(hose, dev, primary);
-
- return 0;
-}
-
-#endif
diff --git a/arch/powerpc/platforms/86xx/Kconfig b/arch/powerpc/platforms/86xx/Kconfig
index 0faebfd..343b76d 100644
--- a/arch/powerpc/platforms/86xx/Kconfig
+++ b/arch/powerpc/platforms/86xx/Kconfig
@@ -14,8 +14,7 @@
config MPC8641
bool
- select PPC_INDIRECT_PCI
- select PPC_INDIRECT_PCI_BE
+ select FSL_PCI if PCI
select PPC_UDBG_16550
select MPIC
default y if MPC8641_HPCN
diff --git a/arch/powerpc/platforms/86xx/Makefile b/arch/powerpc/platforms/86xx/Makefile
index 418fd8f..3376c77 100644
--- a/arch/powerpc/platforms/86xx/Makefile
+++ b/arch/powerpc/platforms/86xx/Makefile
@@ -4,4 +4,3 @@
obj-$(CONFIG_SMP) += mpc86xx_smp.o
obj-$(CONFIG_MPC8641_HPCN) += mpc86xx_hpcn.o
-obj-$(CONFIG_PCI) += pci.o
diff --git a/arch/powerpc/platforms/86xx/mpc86xx.h b/arch/powerpc/platforms/86xx/mpc86xx.h
index 23f7ed2..525ffa1 100644
--- a/arch/powerpc/platforms/86xx/mpc86xx.h
+++ b/arch/powerpc/platforms/86xx/mpc86xx.h
@@ -15,11 +15,6 @@
* mpc86xx_* files. Mostly for use by mpc86xx_setup().
*/
-extern int mpc86xx_add_bridge(struct device_node *dev);
-
-extern int mpc86xx_exclude_device(struct pci_controller *hose,
- u_char bus, u_char devfn);
-
extern void __init mpc86xx_smp_init(void);
#endif /* __MPC86XX_H__ */
diff --git a/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c b/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c
index 5b01ec7..e9eaa07 100644
--- a/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c
+++ b/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c
@@ -31,6 +31,7 @@
#include <asm/mpic.h>
+#include <sysdev/fsl_pci.h>
#include <sysdev/fsl_soc.h>
#include "mpc86xx.h"
@@ -344,8 +345,14 @@
}
#ifdef CONFIG_PCI
- for (np = NULL; (np = of_find_node_by_type(np, "pci")) != NULL;)
- mpc86xx_add_bridge(np);
+ for (np = NULL; (np = of_find_node_by_type(np, "pci")) != NULL;) {
+ struct resource rsrc;
+ of_address_to_resource(np, 0, &rsrc);
+ if ((rsrc.start & 0xfffff) == 0x8000)
+ fsl_add_bridge(np, 1);
+ else
+ fsl_add_bridge(np, 0);
+ }
#endif
printk("MPC86xx HPCN board from Freescale Semiconductor\n");
@@ -424,7 +431,6 @@
return 0;
}
-
define_machine(mpc86xx_hpcn) {
.name = "MPC86xx HPCN",
.probe = mpc86xx_hpcn_probe,
@@ -436,4 +442,5 @@
.time_init = mpc86xx_time_init,
.calibrate_decr = generic_calibrate_decr,
.progress = udbg_progress,
+ .pcibios_fixup_bus = fsl_pcibios_fixup_bus,
};
diff --git a/arch/powerpc/platforms/86xx/pci.c b/arch/powerpc/platforms/86xx/pci.c
deleted file mode 100644
index 73cd5b05..0000000
--- a/arch/powerpc/platforms/86xx/pci.c
+++ /dev/null
@@ -1,238 +0,0 @@
-/*
- * MPC86XX pci setup code
- *
- * Recode: ZHANG WEI <wei.zhang@freescale.com>
- * Initial author: Xianghua Xiao <x.xiao@freescale.com>
- *
- * Copyright 2006 Freescale Semiconductor Inc.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-#include <linux/types.h>
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/pci.h>
-#include <linux/serial.h>
-
-#include <asm/system.h>
-#include <asm/atomic.h>
-#include <asm/io.h>
-#include <asm/prom.h>
-#include <asm/pci-bridge.h>
-#include <sysdev/fsl_soc.h>
-#include <sysdev/fsl_pcie.h>
-
-#include "mpc86xx.h"
-
-#undef DEBUG
-
-#ifdef DEBUG
-#define DBG(fmt, args...) printk(KERN_ERR "%s: " fmt, __FUNCTION__, ## args)
-#else
-#define DBG(fmt, args...)
-#endif
-
-struct pcie_outbound_window_regs {
- uint pexotar; /* 0x.0 - PCI Express outbound translation address register */
- uint pexotear; /* 0x.4 - PCI Express outbound translation extended address register */
- uint pexowbar; /* 0x.8 - PCI Express outbound window base address register */
- char res1[4];
- uint pexowar; /* 0x.10 - PCI Express outbound window attributes register */
- char res2[12];
-};
-
-struct pcie_inbound_window_regs {
- uint pexitar; /* 0x.0 - PCI Express inbound translation address register */
- char res1[4];
- uint pexiwbar; /* 0x.8 - PCI Express inbound window base address register */
- uint pexiwbear; /* 0x.c - PCI Express inbound window base extended address register */
- uint pexiwar; /* 0x.10 - PCI Express inbound window attributes register */
- char res2[12];
-};
-
-static void __init setup_pcie_atmu(struct pci_controller *hose, struct resource *rsrc)
-{
- volatile struct ccsr_pex *pcie;
- volatile struct pcie_outbound_window_regs *pcieow;
- volatile struct pcie_inbound_window_regs *pcieiw;
- int i = 0;
-
- DBG("PCIE memory map start 0x%x, size 0x%x\n", rsrc->start,
- rsrc->end - rsrc->start + 1);
- pcie = ioremap(rsrc->start, rsrc->end - rsrc->start + 1);
-
- /* Disable all windows (except pexowar0 since its ignored) */
- pcie->pexowar1 = 0;
- pcie->pexowar2 = 0;
- pcie->pexowar3 = 0;
- pcie->pexowar4 = 0;
- pcie->pexiwar1 = 0;
- pcie->pexiwar2 = 0;
- pcie->pexiwar3 = 0;
-
- pcieow = (struct pcie_outbound_window_regs *)&pcie->pexotar1;
- pcieiw = (struct pcie_inbound_window_regs *)&pcie->pexitar1;
-
- /* Setup outbound MEM window */
- for(i = 0; i < 3; i++)
- if (hose->mem_resources[i].flags & IORESOURCE_MEM){
- DBG("PCIE MEM resource start 0x%08x, size 0x%08x.\n",
- hose->mem_resources[i].start,
- hose->mem_resources[i].end
- - hose->mem_resources[i].start + 1);
- pcieow->pexotar = (hose->mem_resources[i].start) >> 12
- & 0x000fffff;
- pcieow->pexotear = 0;
- pcieow->pexowbar = (hose->mem_resources[i].start) >> 12
- & 0x000fffff;
- /* Enable, Mem R/W */
- pcieow->pexowar = 0x80044000 |
- (__ilog2(hose->mem_resources[i].end
- - hose->mem_resources[i].start + 1)
- - 1);
- pcieow++;
- }
-
- /* Setup outbound IO window */
- if (hose->io_resource.flags & IORESOURCE_IO){
- DBG("PCIE IO resource start 0x%08x, size 0x%08x, phy base 0x%08x.\n",
- hose->io_resource.start,
- hose->io_resource.end - hose->io_resource.start + 1,
- hose->io_base_phys);
- pcieow->pexotar = (hose->io_resource.start) >> 12 & 0x000fffff;
- pcieow->pexotear = 0;
- pcieow->pexowbar = (hose->io_base_phys) >> 12 & 0x000fffff;
- /* Enable, IO R/W */
- pcieow->pexowar = 0x80088000 | (__ilog2(hose->io_resource.end
- - hose->io_resource.start + 1) - 1);
- }
-
- /* Setup 2G inbound Memory Window @ 0 */
- pcieiw->pexitar = 0x00000000;
- pcieiw->pexiwbar = 0x00000000;
- /* Enable, Prefetch, Local Mem, Snoop R/W, 2G */
- pcieiw->pexiwar = 0xa0f5501e;
-}
-
-static void __init
-mpc86xx_setup_pcie(struct pci_controller *hose, u32 pcie_offset, u32 pcie_size)
-{
- u16 cmd;
-
- DBG("PCIE host controller register offset 0x%08x, size 0x%08x.\n",
- pcie_offset, pcie_size);
-
- early_read_config_word(hose, 0, 0, PCI_COMMAND, &cmd);
- cmd |= PCI_COMMAND_SERR | PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY
- | PCI_COMMAND_IO;
- early_write_config_word(hose, 0, 0, PCI_COMMAND, cmd);
-
- early_write_config_byte(hose, 0, 0, PCI_LATENCY_TIMER, 0x80);
-}
-
-static void __devinit quirk_fsl_pcie_transparent(struct pci_dev *dev)
-{
- struct resource *res;
- int i, res_idx = PCI_BRIDGE_RESOURCES;
- struct pci_controller *hose;
-
- /*
- * Make the bridge be transparent.
- */
- dev->transparent = 1;
-
- hose = pci_bus_to_host(dev->bus);
- if (!hose) {
- printk(KERN_ERR "Can't find hose for bus %d\n",
- dev->bus->number);
- return;
- }
-
- if (hose->io_resource.flags) {
- res = &dev->resource[res_idx++];
- res->start = hose->io_resource.start;
- res->end = hose->io_resource.end;
- res->flags = hose->io_resource.flags;
- }
-
- for (i = 0; i < 3; i++) {
- res = &dev->resource[res_idx + i];
- res->start = hose->mem_resources[i].start;
- res->end = hose->mem_resources[i].end;
- res->flags = hose->mem_resources[i].flags;
- }
-}
-
-
-DECLARE_PCI_FIXUP_EARLY(0x1957, 0x7010, quirk_fsl_pcie_transparent);
-DECLARE_PCI_FIXUP_EARLY(0x1957, 0x7011, quirk_fsl_pcie_transparent);
-
-#define PCIE_LTSSM 0x404 /* PCIe Link Training and Status */
-#define PCIE_LTSSM_L0 0x16 /* L0 state */
-
-int __init mpc86xx_add_bridge(struct device_node *dev)
-{
- int len;
- struct pci_controller *hose;
- struct resource rsrc;
- const int *bus_range;
- int has_address = 0;
- int primary = 0;
- u16 val;
-
- DBG("Adding PCIE host bridge %s\n", dev->full_name);
-
- /* Fetch host bridge registers address */
- has_address = (of_address_to_resource(dev, 0, &rsrc) == 0);
-
- /* Get bus range if any */
- bus_range = of_get_property(dev, "bus-range", &len);
- if (bus_range == NULL || len < 2 * sizeof(int))
- printk(KERN_WARNING "Can't get bus-range for %s, assume"
- " bus 0\n", dev->full_name);
-
- pci_assign_all_buses = 1;
- hose = pcibios_alloc_controller(dev);
- if (!hose)
- return -ENOMEM;
-
- hose->indirect_type = PPC_INDIRECT_TYPE_EXT_REG |
- PPC_INDIRECT_TYPE_SURPRESS_PRIMARY_BUS;
-
- hose->first_busno = bus_range ? bus_range[0] : 0x0;
- hose->last_busno = bus_range ? bus_range[1] : 0xff;
-
- setup_indirect_pci(hose, rsrc.start, rsrc.start + 0x4);
-
- /* Probe the hose link training status */
- early_read_config_word(hose, 0, 0, PCIE_LTSSM, &val);
- if (val < PCIE_LTSSM_L0)
- return -ENXIO;
-
- /* Setup the PCIE host controller. */
- mpc86xx_setup_pcie(hose, rsrc.start, rsrc.end - rsrc.start + 1);
-
- if ((rsrc.start & 0xfffff) == 0x8000)
- primary = 1;
-
- printk(KERN_INFO "Found MPC86xx PCIE host bridge at 0x%08lx. "
- "Firmware bus number: %d->%d\n",
- (unsigned long) rsrc.start,
- hose->first_busno, hose->last_busno);
-
- DBG(" ->Hose at 0x%p, cfg_addr=0x%p,cfg_data=0x%p\n",
- hose, hose->cfg_addr, hose->cfg_data);
-
- /* Interpret the "ranges" property */
- /* This also maps the I/O region and sets isa_io/mem_base */
- pci_process_bridge_OF_ranges(hose, dev, primary);
-
- /* Setup PEX window registers */
- setup_pcie_atmu(hose, &rsrc);
-
- return 0;
-}
diff --git a/arch/powerpc/platforms/chrp/pci.c b/arch/powerpc/platforms/chrp/pci.c
index 3690624..28d1647 100644
--- a/arch/powerpc/platforms/chrp/pci.c
+++ b/arch/powerpc/platforms/chrp/pci.c
@@ -181,7 +181,7 @@
}
iounmap(reg);
- setup_indirect_pci(hose, r.start + 0xf8000, r.start + 0xf8010);
+ setup_indirect_pci(hose, r.start + 0xf8000, r.start + 0xf8010, 0);
}
/* Marvell Discovery II based Pegasos 2 */
@@ -277,13 +277,14 @@
hose->cfg_data = p;
gg2_pci_config_base = p;
} else if (is_pegasos == 1) {
- setup_indirect_pci(hose, 0xfec00cf8, 0xfee00cfc);
+ setup_indirect_pci(hose, 0xfec00cf8, 0xfee00cfc, 0);
} else if (is_pegasos == 2) {
setup_peg2(hose, dev);
} else if (!strncmp(model, "IBM,CPC710", 10)) {
setup_indirect_pci(hose,
r.start + 0x000f8000,
- r.start + 0x000f8010);
+ r.start + 0x000f8010,
+ 0);
if (index == 0) {
dma = of_get_property(dev, "system-dma-base",
&len);
diff --git a/arch/powerpc/platforms/embedded6xx/linkstation.c b/arch/powerpc/platforms/embedded6xx/linkstation.c
index f4d0a7a..bd5ca58 100644
--- a/arch/powerpc/platforms/embedded6xx/linkstation.c
+++ b/arch/powerpc/platforms/embedded6xx/linkstation.c
@@ -73,7 +73,7 @@
return -ENOMEM;
hose->first_busno = bus_range ? bus_range[0] : 0;
hose->last_busno = bus_range ? bus_range[1] : 0xff;
- setup_indirect_pci(hose, 0xfec00000, 0xfee00000);
+ setup_indirect_pci(hose, 0xfec00000, 0xfee00000, 0);
/* Interpret the "ranges" property */
/* This also maps the I/O region and sets isa_io/mem_base */
diff --git a/arch/powerpc/sysdev/Makefile b/arch/powerpc/sysdev/Makefile
index 484eb4e..08ce31e 100644
--- a/arch/powerpc/sysdev/Makefile
+++ b/arch/powerpc/sysdev/Makefile
@@ -12,6 +12,7 @@
obj-$(CONFIG_U3_DART) += dart_iommu.o
obj-$(CONFIG_MMIO_NVRAM) += mmio_nvram.o
obj-$(CONFIG_FSL_SOC) += fsl_soc.o
+obj-$(CONFIG_FSL_PCI) += fsl_pci.o
obj-$(CONFIG_TSI108_BRIDGE) += tsi108_pci.o tsi108_dev.o
obj-$(CONFIG_QUICC_ENGINE) += qe_lib/
mv64x60-$(CONFIG_PCI) += mv64x60_pci.o
diff --git a/arch/powerpc/sysdev/fsl_pci.c b/arch/powerpc/sysdev/fsl_pci.c
new file mode 100644
index 0000000..51c2233
--- /dev/null
+++ b/arch/powerpc/sysdev/fsl_pci.c
@@ -0,0 +1,257 @@
+/*
+ * MPC85xx/86xx PCI/PCIE support routing.
+ *
+ * Copyright 2007 Freescale Semiconductor, Inc
+ *
+ * Initial author: Xianghua Xiao <x.xiao@freescale.com>
+ * Recode: ZHANG WEI <wei.zhang@freescale.com>
+ * Rewrite the routing for Frescale PCI and PCI Express
+ * Roy Zang <tie-fei.zang@freescale.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/delay.h>
+#include <linux/string.h>
+#include <linux/init.h>
+#include <linux/bootmem.h>
+
+#include <asm/io.h>
+#include <asm/prom.h>
+#include <asm/pci-bridge.h>
+#include <asm/machdep.h>
+#include <sysdev/fsl_soc.h>
+#include <sysdev/fsl_pci.h>
+
+/* atmu setup for fsl pci/pcie controller */
+void __init setup_pci_atmu(struct pci_controller *hose, struct resource *rsrc)
+{
+ struct ccsr_pci __iomem *pci;
+ int i;
+
+ pr_debug("PCI memory map start 0x%x, size 0x%x\n", rsrc->start,
+ rsrc->end - rsrc->start + 1);
+ pci = ioremap(rsrc->start, rsrc->end - rsrc->start + 1);
+
+ /* Disable all windows (except powar0 since its ignored) */
+ for(i = 1; i < 5; i++)
+ out_be32(&pci->pow[i].powar, 0);
+ for(i = 0; i < 3; i++)
+ out_be32(&pci->piw[i].piwar, 0);
+
+ /* Setup outbound MEM window */
+ for(i = 0; i < 3; i++)
+ if (hose->mem_resources[i].flags & IORESOURCE_MEM){
+ pr_debug("PCI MEM resource start 0x%08x, size 0x%08x.\n",
+ hose->mem_resources[i].start,
+ hose->mem_resources[i].end
+ - hose->mem_resources[i].start + 1);
+ out_be32(&pci->pow[i+1].potar,
+ (hose->mem_resources[i].start >> 12)
+ & 0x000fffff);
+ out_be32(&pci->pow[i+1].potear, 0);
+ out_be32(&pci->pow[i+1].powbar,
+ (hose->mem_resources[i].start >> 12)
+ & 0x000fffff);
+ /* Enable, Mem R/W */
+ out_be32(&pci->pow[i+1].powar, 0x80044000
+ | (__ilog2(hose->mem_resources[i].end
+ - hose->mem_resources[i].start + 1) - 1));
+ }
+
+ /* Setup outbound IO window */
+ if (hose->io_resource.flags & IORESOURCE_IO){
+ pr_debug("PCI IO resource start 0x%08x, size 0x%08x, phy base 0x%08x.\n",
+ hose->io_resource.start,
+ hose->io_resource.end - hose->io_resource.start + 1,
+ hose->io_base_phys);
+ out_be32(&pci->pow[i+1].potar, (hose->io_resource.start >> 12)
+ & 0x000fffff);
+ out_be32(&pci->pow[i+1].potear, 0);
+ out_be32(&pci->pow[i+1].powbar, (hose->io_base_phys >> 12)
+ & 0x000fffff);
+ /* Enable, IO R/W */
+ out_be32(&pci->pow[i+1].powar, 0x80088000
+ | (__ilog2(hose->io_resource.end
+ - hose->io_resource.start + 1) - 1));
+ }
+
+ /* Setup 2G inbound Memory Window @ 1 */
+ out_be32(&pci->piw[2].pitar, 0x00000000);
+ out_be32(&pci->piw[2].piwbar,0x00000000);
+ out_be32(&pci->piw[2].piwar, PIWAR_2G);
+}
+
+void __init setup_pci_cmd(struct pci_controller *hose)
+{
+ u16 cmd;
+ int cap_x;
+
+ early_read_config_word(hose, 0, 0, PCI_COMMAND, &cmd);
+ cmd |= PCI_COMMAND_SERR | PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY
+ | PCI_COMMAND_IO;
+ early_write_config_word(hose, 0, 0, PCI_COMMAND, cmd);
+
+ cap_x = early_find_capability(hose, 0, 0, PCI_CAP_ID_PCIX);
+ if (cap_x) {
+ int pci_x_cmd = cap_x + PCI_X_CMD;
+ cmd = PCI_X_CMD_MAX_SPLIT | PCI_X_CMD_MAX_READ
+ | PCI_X_CMD_ERO | PCI_X_CMD_DPERR_E;
+ early_write_config_word(hose, 0, 0, pci_x_cmd, cmd);
+ } else {
+ early_write_config_byte(hose, 0, 0, PCI_LATENCY_TIMER, 0x80);
+ }
+}
+
+static void __devinit quirk_fsl_pcie_transparent(struct pci_dev *dev)
+{
+ struct resource *res;
+ int i, res_idx = PCI_BRIDGE_RESOURCES;
+ struct pci_controller *hose;
+
+ /* if we aren't a PCIe don't bother */
+ if (!pci_find_capability(dev, PCI_CAP_ID_EXP))
+ return ;
+
+ /*
+ * Make the bridge be transparent.
+ */
+ dev->transparent = 1;
+
+ hose = pci_bus_to_host(dev->bus);
+ if (!hose) {
+ printk(KERN_ERR "Can't find hose for bus %d\n",
+ dev->bus->number);
+ return;
+ }
+
+ /* Clear out any of the virtual P2P bridge registers */
+ pci_write_config_word(dev, PCI_IO_BASE_UPPER16, 0);
+ pci_write_config_word(dev, PCI_IO_LIMIT_UPPER16, 0);
+ pci_write_config_byte(dev, PCI_IO_BASE, 0x10);
+ pci_write_config_byte(dev, PCI_IO_LIMIT, 0);
+ pci_write_config_word(dev, PCI_MEMORY_BASE, 0x10);
+ pci_write_config_word(dev, PCI_MEMORY_LIMIT, 0);
+ pci_write_config_word(dev, PCI_PREF_BASE_UPPER32, 0x0);
+ pci_write_config_word(dev, PCI_PREF_LIMIT_UPPER32, 0x0);
+ pci_write_config_word(dev, PCI_PREF_MEMORY_BASE, 0x10);
+ pci_write_config_word(dev, PCI_PREF_MEMORY_LIMIT, 0);
+
+ if (hose->io_resource.flags) {
+ res = &dev->resource[res_idx++];
+ res->start = hose->io_resource.start;
+ res->end = hose->io_resource.end;
+ res->flags = hose->io_resource.flags;
+ update_bridge_resource(dev, res);
+ }
+
+ for (i = 0; i < 3; i++) {
+ res = &dev->resource[res_idx + i];
+ res->start = hose->mem_resources[i].start;
+ res->end = hose->mem_resources[i].end;
+ res->flags = hose->mem_resources[i].flags;
+ update_bridge_resource(dev, res);
+ }
+}
+
+int __init fsl_pcie_check_link(struct pci_controller *hose)
+{
+ u16 val;
+ early_read_config_word(hose, 0, 0, PCIE_LTSSM, &val);
+ if (val < PCIE_LTSSM_L0)
+ return 1;
+ return 0;
+}
+
+void fsl_pcibios_fixup_bus(struct pci_bus *bus)
+{
+ struct pci_controller *hose = (struct pci_controller *) bus->sysdata;
+ int i;
+
+ /* deal with bogus pci_bus when we don't have anything connected on PCIe */
+ if (hose->indirect_type & PPC_INDIRECT_TYPE_NO_PCIE_LINK) {
+ if (bus->parent) {
+ for (i = 0; i < 4; ++i)
+ bus->resource[i] = bus->parent->resource[i];
+ }
+ }
+}
+
+int __init fsl_add_bridge(struct device_node *dev, int is_primary)
+{
+ int len;
+ struct pci_controller *hose;
+ struct resource rsrc;
+ const int *bus_range;
+
+ pr_debug("Adding PCI host bridge %s\n", dev->full_name);
+
+ /* Fetch host bridge registers address */
+ if (of_address_to_resource(dev, 0, &rsrc)) {
+ printk(KERN_WARNING "Can't get pci register base!");
+ return -ENOMEM;
+ }
+
+ /* Get bus range if any */
+ bus_range = of_get_property(dev, "bus-range", &len);
+ if (bus_range == NULL || len < 2 * sizeof(int))
+ printk(KERN_WARNING "Can't get bus-range for %s, assume"
+ " bus 0\n", dev->full_name);
+
+ pci_assign_all_buses = 1;
+ hose = pcibios_alloc_controller(dev);
+ if (!hose)
+ return -ENOMEM;
+
+ hose->first_busno = bus_range ? bus_range[0] : 0x0;
+ hose->last_busno = bus_range ? bus_range[1] : 0xff;
+
+ setup_indirect_pci(hose, rsrc.start, rsrc.start + 0x4,
+ PPC_INDIRECT_TYPE_BIG_ENDIAN);
+ setup_pci_cmd(hose);
+
+ /* check PCI express link status */
+ if (early_find_capability(hose, 0, 0, PCI_CAP_ID_EXP)) {
+ hose->indirect_type = PPC_INDIRECT_TYPE_EXT_REG |
+ PPC_INDIRECT_TYPE_SURPRESS_PRIMARY_BUS;
+ if (fsl_pcie_check_link(hose))
+ hose->indirect_type |= PPC_INDIRECT_TYPE_NO_PCIE_LINK;
+ }
+
+ printk(KERN_INFO "Found FSL PCI host bridge at 0x%016llx."
+ "Firmware bus number: %d->%d\n",
+ (unsigned long long)rsrc.start, hose->first_busno,
+ hose->last_busno);
+
+ pr_debug(" ->Hose at 0x%p, cfg_addr=0x%p,cfg_data=0x%p\n",
+ hose, hose->cfg_addr, hose->cfg_data);
+
+ /* Interpret the "ranges" property */
+ /* This also maps the I/O region and sets isa_io/mem_base */
+ pci_process_bridge_OF_ranges(hose, dev, is_primary);
+
+ /* Setup PEX window registers */
+ setup_pci_atmu(hose, &rsrc);
+
+ return 0;
+}
+
+DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8548E, quirk_fsl_pcie_transparent);
+DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8548, quirk_fsl_pcie_transparent);
+DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8543E, quirk_fsl_pcie_transparent);
+DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8543, quirk_fsl_pcie_transparent);
+DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8547E, quirk_fsl_pcie_transparent);
+DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8545E, quirk_fsl_pcie_transparent);
+DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8545, quirk_fsl_pcie_transparent);
+DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8568E, quirk_fsl_pcie_transparent);
+DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8568, quirk_fsl_pcie_transparent);
+DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8567E, quirk_fsl_pcie_transparent);
+DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8567, quirk_fsl_pcie_transparent);
+DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8544E, quirk_fsl_pcie_transparent);
+DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8544, quirk_fsl_pcie_transparent);
+DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8641, quirk_fsl_pcie_transparent);
+DECLARE_PCI_FIXUP_EARLY(0x1957, PCI_DEVICE_ID_MPC8641D, quirk_fsl_pcie_transparent);
diff --git a/arch/powerpc/sysdev/fsl_pci.h b/arch/powerpc/sysdev/fsl_pci.h
new file mode 100644
index 0000000..37b04ad
--- /dev/null
+++ b/arch/powerpc/sysdev/fsl_pci.h
@@ -0,0 +1,88 @@
+/*
+ * MPC85xx/86xx PCI Express structure define
+ *
+ * Copyright 2007 Freescale Semiconductor, Inc
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+
+#ifdef __KERNEL__
+#ifndef __POWERPC_FSL_PCI_H
+#define __POWERPC_FSL_PCI_H
+
+#define PCIE_LTSSM 0x0404 /* PCIE Link Training and Status */
+#define PCIE_LTSSM_L0 0x16 /* L0 state */
+#define PIWAR_2G 0xa0f5501e /* Enable, Prefetch, Local Mem, Snoop R/W, 2G */
+
+/* PCI/PCI Express outbound window reg */
+struct pci_outbound_window_regs {
+ __be32 potar; /* 0x.0 - Outbound translation address register */
+ __be32 potear; /* 0x.4 - Outbound translation extended address register */
+ __be32 powbar; /* 0x.8 - Outbound window base address register */
+ u8 res1[4];
+ __be32 powar; /* 0x.10 - Outbound window attributes register */
+ u8 res2[12];
+};
+
+/* PCI/PCI Express inbound window reg */
+struct pci_inbound_window_regs {
+ __be32 pitar; /* 0x.0 - Inbound translation address register */
+ u8 res1[4];
+ __be32 piwbar; /* 0x.8 - Inbound window base address register */
+ __be32 piwbear; /* 0x.c - Inbound window base extended address register */
+ __be32 piwar; /* 0x.10 - Inbound window attributes register */
+ u8 res2[12];
+};
+
+/* PCI/PCI Express IO block registers for 85xx/86xx */
+struct ccsr_pci {
+ __be32 config_addr; /* 0x.000 - PCI/PCIE Configuration Address Register */
+ __be32 config_data; /* 0x.004 - PCI/PCIE Configuration Data Register */
+ __be32 int_ack; /* 0x.008 - PCI Interrupt Acknowledge Register */
+ __be32 pex_otb_cpl_tor; /* 0x.00c - PCIE Outbound completion timeout register */
+ __be32 pex_conf_tor; /* 0x.010 - PCIE configuration timeout register */
+ u8 res2[12];
+ __be32 pex_pme_mes_dr; /* 0x.020 - PCIE PME and message detect register */
+ __be32 pex_pme_mes_disr; /* 0x.024 - PCIE PME and message disable register */
+ __be32 pex_pme_mes_ier; /* 0x.028 - PCIE PME and message interrupt enable register */
+ __be32 pex_pmcr; /* 0x.02c - PCIE power management command register */
+ u8 res3[3024];
+
+/* PCI/PCI Express outbound window 0-4
+ * Window 0 is the default window and is the only window enabled upon reset.
+ * The default outbound register set is used when a transaction misses
+ * in all of the other outbound windows.
+ */
+ struct pci_outbound_window_regs pow[5];
+
+ u8 res14[256];
+
+/* PCI/PCI Express inbound window 3-1
+ * inbound window 1 supports only a 32-bit base address and does not
+ * define an inbound window base extended address register.
+ */
+ struct pci_inbound_window_regs piw[3];
+
+ __be32 pex_err_dr; /* 0x.e00 - PCI/PCIE error detect register */
+ u8 res21[4];
+ __be32 pex_err_en; /* 0x.e08 - PCI/PCIE error interrupt enable register */
+ u8 res22[4];
+ __be32 pex_err_disr; /* 0x.e10 - PCI/PCIE error disable register */
+ u8 res23[12];
+ __be32 pex_err_cap_stat; /* 0x.e20 - PCI/PCIE error capture status register */
+ u8 res24[4];
+ __be32 pex_err_cap_r0; /* 0x.e28 - PCIE error capture register 0 */
+ __be32 pex_err_cap_r1; /* 0x.e2c - PCIE error capture register 0 */
+ __be32 pex_err_cap_r2; /* 0x.e30 - PCIE error capture register 0 */
+ __be32 pex_err_cap_r3; /* 0x.e34 - PCIE error capture register 0 */
+};
+
+extern int fsl_add_bridge(struct device_node *dev, int is_primary);
+extern void fsl_pcibios_fixup_bus(struct pci_bus *bus);
+
+#endif /* __POWERPC_FSL_PCI_H */
+#endif /* __KERNEL__ */
diff --git a/arch/powerpc/sysdev/fsl_pcie.h b/arch/powerpc/sysdev/fsl_pcie.h
deleted file mode 100644
index 8d9779c..0000000
--- a/arch/powerpc/sysdev/fsl_pcie.h
+++ /dev/null
@@ -1,94 +0,0 @@
-/*
- * MPC85xx/86xx PCI Express structure define
- *
- * Copyright 2007 Freescale Semiconductor, Inc
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- */
-
-#ifdef __KERNEL__
-#ifndef __POWERPC_FSL_PCIE_H
-#define __POWERPC_FSL_PCIE_H
-
-/* PCIE Express IO block registers in 85xx/86xx */
-
-struct ccsr_pex {
- __be32 __iomem pex_config_addr; /* 0x.000 - PCI Express Configuration Address Register */
- __be32 __iomem pex_config_data; /* 0x.004 - PCI Express Configuration Data Register */
- u8 __iomem res1[4];
- __be32 __iomem pex_otb_cpl_tor; /* 0x.00c - PCI Express Outbound completion timeout register */
- __be32 __iomem pex_conf_tor; /* 0x.010 - PCI Express configuration timeout register */
- u8 __iomem res2[12];
- __be32 __iomem pex_pme_mes_dr; /* 0x.020 - PCI Express PME and message detect register */
- __be32 __iomem pex_pme_mes_disr; /* 0x.024 - PCI Express PME and message disable register */
- __be32 __iomem pex_pme_mes_ier; /* 0x.028 - PCI Express PME and message interrupt enable register */
- __be32 __iomem pex_pmcr; /* 0x.02c - PCI Express power management command register */
- u8 __iomem res3[3024];
- __be32 __iomem pexotar0; /* 0x.c00 - PCI Express outbound translation address register 0 */
- __be32 __iomem pexotear0; /* 0x.c04 - PCI Express outbound translation extended address register 0*/
- u8 __iomem res4[8];
- __be32 __iomem pexowar0; /* 0x.c10 - PCI Express outbound window attributes register 0*/
- u8 __iomem res5[12];
- __be32 __iomem pexotar1; /* 0x.c20 - PCI Express outbound translation address register 1 */
- __be32 __iomem pexotear1; /* 0x.c24 - PCI Express outbound translation extended address register 1*/
- __be32 __iomem pexowbar1; /* 0x.c28 - PCI Express outbound window base address register 1*/
- u8 __iomem res6[4];
- __be32 __iomem pexowar1; /* 0x.c30 - PCI Express outbound window attributes register 1*/
- u8 __iomem res7[12];
- __be32 __iomem pexotar2; /* 0x.c40 - PCI Express outbound translation address register 2 */
- __be32 __iomem pexotear2; /* 0x.c44 - PCI Express outbound translation extended address register 2*/
- __be32 __iomem pexowbar2; /* 0x.c48 - PCI Express outbound window base address register 2*/
- u8 __iomem res8[4];
- __be32 __iomem pexowar2; /* 0x.c50 - PCI Express outbound window attributes register 2*/
- u8 __iomem res9[12];
- __be32 __iomem pexotar3; /* 0x.c60 - PCI Express outbound translation address register 3 */
- __be32 __iomem pexotear3; /* 0x.c64 - PCI Express outbound translation extended address register 3*/
- __be32 __iomem pexowbar3; /* 0x.c68 - PCI Express outbound window base address register 3*/
- u8 __iomem res10[4];
- __be32 __iomem pexowar3; /* 0x.c70 - PCI Express outbound window attributes register 3*/
- u8 __iomem res11[12];
- __be32 __iomem pexotar4; /* 0x.c80 - PCI Express outbound translation address register 4 */
- __be32 __iomem pexotear4; /* 0x.c84 - PCI Express outbound translation extended address register 4*/
- __be32 __iomem pexowbar4; /* 0x.c88 - PCI Express outbound window base address register 4*/
- u8 __iomem res12[4];
- __be32 __iomem pexowar4; /* 0x.c90 - PCI Express outbound window attributes register 4*/
- u8 __iomem res13[12];
- u8 __iomem res14[256];
- __be32 __iomem pexitar3; /* 0x.da0 - PCI Express inbound translation address register 3 */
- u8 __iomem res15[4];
- __be32 __iomem pexiwbar3; /* 0x.da8 - PCI Express inbound window base address register 3 */
- __be32 __iomem pexiwbear3; /* 0x.dac - PCI Express inbound window base extended address register 3 */
- __be32 __iomem pexiwar3; /* 0x.db0 - PCI Express inbound window attributes register 3 */
- u8 __iomem res16[12];
- __be32 __iomem pexitar2; /* 0x.dc0 - PCI Express inbound translation address register 2 */
- u8 __iomem res17[4];
- __be32 __iomem pexiwbar2; /* 0x.dc8 - PCI Express inbound window base address register 2 */
- __be32 __iomem pexiwbear2; /* 0x.dcc - PCI Express inbound window base extended address register 2 */
- __be32 __iomem pexiwar2; /* 0x.dd0 - PCI Express inbound window attributes register 2 */
- u8 __iomem res18[12];
- __be32 __iomem pexitar1; /* 0x.de0 - PCI Express inbound translation address register 2 */
- u8 __iomem res19[4];
- __be32 __iomem pexiwbar1; /* 0x.de8 - PCI Express inbound window base address register 2 */
- __be32 __iomem pexiwbear1; /* 0x.dec - PCI Express inbound window base extended address register 2 */
- __be32 __iomem pexiwar1; /* 0x.df0 - PCI Express inbound window attributes register 2 */
- u8 __iomem res20[12];
- __be32 __iomem pex_err_dr; /* 0x.e00 - PCI Express error detect register */
- u8 __iomem res21[4];
- __be32 __iomem pex_err_en; /* 0x.e08 - PCI Express error interrupt enable register */
- u8 __iomem res22[4];
- __be32 __iomem pex_err_disr; /* 0x.e10 - PCI Express error disable register */
- u8 __iomem res23[12];
- __be32 __iomem pex_err_cap_stat; /* 0x.e20 - PCI Express error capture status register */
- u8 __iomem res24[4];
- __be32 __iomem pex_err_cap_r0; /* 0x.e28 - PCI Express error capture register 0 */
- __be32 __iomem pex_err_cap_r1; /* 0x.e2c - PCI Express error capture register 0 */
- __be32 __iomem pex_err_cap_r2; /* 0x.e30 - PCI Express error capture register 0 */
- __be32 __iomem pex_err_cap_r3; /* 0x.e34 - PCI Express error capture register 0 */
-};
-
-#endif /* __POWERPC_FSL_PCIE_H */
-#endif /* __KERNEL__ */
diff --git a/arch/powerpc/sysdev/grackle.c b/arch/powerpc/sysdev/grackle.c
index 4205362..11ad562 100644
--- a/arch/powerpc/sysdev/grackle.c
+++ b/arch/powerpc/sysdev/grackle.c
@@ -55,7 +55,7 @@
void __init setup_grackle(struct pci_controller *hose)
{
- setup_indirect_pci(hose, 0xfec00000, 0xfee00000);
+ setup_indirect_pci(hose, 0xfec00000, 0xfee00000, 0);
if (machine_is_compatible("PowerMac1,1"))
pci_assign_all_buses = 1;
if (machine_is_compatible("AAPL,PowerBook1998"))
diff --git a/arch/powerpc/sysdev/indirect_pci.c b/arch/powerpc/sysdev/indirect_pci.c
index c7e6e85..a8ac2df 100644
--- a/arch/powerpc/sysdev/indirect_pci.c
+++ b/arch/powerpc/sysdev/indirect_pci.c
@@ -20,12 +20,6 @@
#include <asm/pci-bridge.h>
#include <asm/machdep.h>
-#ifdef CONFIG_PPC_INDIRECT_PCI_BE
-#define PCI_CFG_OUT out_be32
-#else
-#define PCI_CFG_OUT out_le32
-#endif
-
static int
indirect_read_config(struct pci_bus *bus, unsigned int devfn, int offset,
int len, u32 *val)
@@ -35,10 +29,17 @@
u8 cfg_type = 0;
u32 bus_no, reg;
+ if (hose->indirect_type & PPC_INDIRECT_TYPE_NO_PCIE_LINK) {
+ if (bus->number != hose->first_busno)
+ return PCIBIOS_DEVICE_NOT_FOUND;
+ if (devfn != 0)
+ return PCIBIOS_DEVICE_NOT_FOUND;
+ }
+
if (ppc_md.pci_exclude_device)
if (ppc_md.pci_exclude_device(hose, bus->number, devfn))
return PCIBIOS_DEVICE_NOT_FOUND;
-
+
if (hose->indirect_type & PPC_INDIRECT_TYPE_SET_CFG_TYPE)
if (bus->number != hose->first_busno)
cfg_type = 1;
@@ -51,9 +52,12 @@
else
reg = offset & 0xfc;
- PCI_CFG_OUT(hose->cfg_addr,
- (0x80000000 | (bus_no << 16)
- | (devfn << 8) | reg | cfg_type));
+ if (hose->indirect_type & PPC_INDIRECT_TYPE_BIG_ENDIAN)
+ out_be32(hose->cfg_addr, (0x80000000 | (bus_no << 16) |
+ (devfn << 8) | reg | cfg_type));
+ else
+ out_le32(hose->cfg_addr, (0x80000000 | (bus_no << 16) |
+ (devfn << 8) | reg | cfg_type));
/*
* Note: the caller has already checked that offset is
@@ -83,6 +87,13 @@
u8 cfg_type = 0;
u32 bus_no, reg;
+ if (hose->indirect_type & PPC_INDIRECT_TYPE_NO_PCIE_LINK) {
+ if (bus->number != hose->first_busno)
+ return PCIBIOS_DEVICE_NOT_FOUND;
+ if (devfn != 0)
+ return PCIBIOS_DEVICE_NOT_FOUND;
+ }
+
if (ppc_md.pci_exclude_device)
if (ppc_md.pci_exclude_device(hose, bus->number, devfn))
return PCIBIOS_DEVICE_NOT_FOUND;
@@ -99,9 +110,12 @@
else
reg = offset & 0xfc;
- PCI_CFG_OUT(hose->cfg_addr,
- (0x80000000 | (bus_no << 16)
- | (devfn << 8) | reg | cfg_type));
+ if (hose->indirect_type & PPC_INDIRECT_TYPE_BIG_ENDIAN)
+ out_be32(hose->cfg_addr, (0x80000000 | (bus_no << 16) |
+ (devfn << 8) | reg | cfg_type));
+ else
+ out_le32(hose->cfg_addr, (0x80000000 | (bus_no << 16) |
+ (devfn << 8) | reg | cfg_type));
/* surpress setting of PCI_PRIMARY_BUS */
if (hose->indirect_type & PPC_INDIRECT_TYPE_SURPRESS_PRIMARY_BUS)
@@ -135,24 +149,15 @@
};
void __init
-setup_indirect_pci_nomap(struct pci_controller* hose, void __iomem * cfg_addr,
- void __iomem * cfg_data)
-{
- hose->cfg_addr = cfg_addr;
- hose->cfg_data = cfg_data;
- hose->ops = &indirect_pci_ops;
-}
-
-void __init
-setup_indirect_pci(struct pci_controller* hose, u32 cfg_addr, u32 cfg_data)
+setup_indirect_pci(struct pci_controller* hose, u32 cfg_addr, u32 cfg_data, u32 flags)
{
unsigned long base = cfg_addr & PAGE_MASK;
- void __iomem *mbase, *addr, *data;
+ void __iomem *mbase;
mbase = ioremap(base, PAGE_SIZE);
- addr = mbase + (cfg_addr & ~PAGE_MASK);
+ hose->cfg_addr = mbase + (cfg_addr & ~PAGE_MASK);
if ((cfg_data & PAGE_MASK) != base)
mbase = ioremap(cfg_data & PAGE_MASK, PAGE_SIZE);
- data = mbase + (cfg_data & ~PAGE_MASK);
- setup_indirect_pci_nomap(hose, addr, data);
+ hose->cfg_data = mbase + (cfg_data & ~PAGE_MASK);
+ hose->ops = &indirect_pci_ops;
}
diff --git a/arch/powerpc/sysdev/mv64x60_pci.c b/arch/powerpc/sysdev/mv64x60_pci.c
index 45db86c..9b3baa7 100644
--- a/arch/powerpc/sysdev/mv64x60_pci.c
+++ b/arch/powerpc/sysdev/mv64x60_pci.c
@@ -144,7 +144,7 @@
hose->first_busno = bus_range ? bus_range[0] : 0;
hose->last_busno = bus_range ? bus_range[1] : 0xff;
- setup_indirect_pci(hose, rsrc.start, rsrc.start + 4);
+ setup_indirect_pci(hose, rsrc.start, rsrc.start + 4, 0);
hose->self_busno = hose->first_busno;
printk(KERN_INFO "Found MV64x60 PCI host bridge at 0x%016llx. "
diff --git a/include/asm-powerpc/pci-bridge.h b/include/asm-powerpc/pci-bridge.h
index e72c2a6..d53e0eb 100644
--- a/include/asm-powerpc/pci-bridge.h
+++ b/include/asm-powerpc/pci-bridge.h
@@ -45,10 +45,17 @@
* on Freescale PCI-e controllers since they used the PCI_PRIMARY_BUS
* to determine which bus number to match on when generating type0
* config cycles
+ * NO_PCIE_LINK - the Freescale PCI-e controllers have issues with
+ * hanging if we don't have link and try to do config cycles to
+ * anything but the PHB. Only allow talking to the PHB if this is
+ * set.
+ * BIG_ENDIAN - cfg_addr is a big endian register
*/
#define PPC_INDIRECT_TYPE_SET_CFG_TYPE (0x00000001)
#define PPC_INDIRECT_TYPE_EXT_REG (0x00000002)
#define PPC_INDIRECT_TYPE_SURPRESS_PRIMARY_BUS (0x00000004)
+#define PPC_INDIRECT_TYPE_NO_PCIE_LINK (0x00000008)
+#define PPC_INDIRECT_TYPE_BIG_ENDIAN (0x00000010)
u32 indirect_type;
/* Currently, we limit ourselves to 1 IO range and 3 mem
@@ -79,11 +86,14 @@
int early_write_config_dword(struct pci_controller *hose, int bus, int dev_fn,
int where, u32 val);
-extern void setup_indirect_pci_nomap(struct pci_controller* hose,
- void __iomem *cfg_addr, void __iomem *cfg_data);
+extern int early_find_capability(struct pci_controller *hose, int bus,
+ int dev_fn, int cap);
+
extern void setup_indirect_pci(struct pci_controller* hose,
- u32 cfg_addr, u32 cfg_data);
+ u32 cfg_addr, u32 cfg_data, u32 flags);
extern void setup_grackle(struct pci_controller *hose);
+extern void __init update_bridge_resource(struct pci_dev *dev,
+ struct resource *res);
#else
diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h
index 42d3278..dc41ad4 100644
--- a/include/linux/pci_ids.h
+++ b/include/linux/pci_ids.h
@@ -2079,6 +2079,23 @@
#define PCI_VENDOR_ID_TDI 0x192E
#define PCI_DEVICE_ID_TDI_EHCI 0x0101
+#define PCI_VENDOR_ID_FREESCALE 0x1957
+#define PCI_DEVICE_ID_MPC8548E 0x0012
+#define PCI_DEVICE_ID_MPC8548 0x0013
+#define PCI_DEVICE_ID_MPC8543E 0x0014
+#define PCI_DEVICE_ID_MPC8543 0x0015
+#define PCI_DEVICE_ID_MPC8547E 0x0018
+#define PCI_DEVICE_ID_MPC8545E 0x0019
+#define PCI_DEVICE_ID_MPC8545 0x001a
+#define PCI_DEVICE_ID_MPC8568E 0x0020
+#define PCI_DEVICE_ID_MPC8568 0x0021
+#define PCI_DEVICE_ID_MPC8567E 0x0022
+#define PCI_DEVICE_ID_MPC8567 0x0023
+#define PCI_DEVICE_ID_MPC8544E 0x0030
+#define PCI_DEVICE_ID_MPC8544 0x0031
+#define PCI_DEVICE_ID_MPC8641 0x7010
+#define PCI_DEVICE_ID_MPC8641D 0x7011
+
#define PCI_VENDOR_ID_PASEMI 0x1959
#define PCI_VENDOR_ID_ATTANSIC 0x1969