of/pci: move of_irq_map_pci() into generic code
There is a tiny difference between PPC32 and PPC64. Microblaze uses the
PPC32 variant.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
[grant.likely@secretlab.ca: Added comment to #endif, moved documentation
block to function implementation, fixed for non ppc and microblaze
compiles]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
diff --git a/arch/powerpc/kernel/pci-common.c b/arch/powerpc/kernel/pci-common.c
index 10a44e6..eb341be 100644
--- a/arch/powerpc/kernel/pci-common.c
+++ b/arch/powerpc/kernel/pci-common.c
@@ -22,6 +22,7 @@
#include <linux/init.h>
#include <linux/bootmem.h>
#include <linux/of_address.h>
+#include <linux/of_pci.h>
#include <linux/mm.h>
#include <linux/list.h>
#include <linux/syscalls.h>
diff --git a/arch/powerpc/kernel/prom_parse.c b/arch/powerpc/kernel/prom_parse.c
index c2b7a07..47187cc 100644
--- a/arch/powerpc/kernel/prom_parse.c
+++ b/arch/powerpc/kernel/prom_parse.c
@@ -2,95 +2,11 @@
#include <linux/kernel.h>
#include <linux/string.h>
-#include <linux/pci_regs.h>
#include <linux/module.h>
#include <linux/ioport.h>
#include <linux/etherdevice.h>
#include <linux/of_address.h>
#include <asm/prom.h>
-#include <asm/pci-bridge.h>
-
-#ifdef CONFIG_PCI
-int of_irq_map_pci(struct pci_dev *pdev, struct of_irq *out_irq)
-{
- struct device_node *dn, *ppnode;
- struct pci_dev *ppdev;
- u32 lspec;
- u32 laddr[3];
- u8 pin;
- int rc;
-
- /* Check if we have a device node, if yes, fallback to standard OF
- * parsing
- */
- dn = pci_device_to_OF_node(pdev);
- if (dn) {
- rc = of_irq_map_one(dn, 0, out_irq);
- if (!rc)
- return rc;
- }
-
- /* Ok, we don't, time to have fun. Let's start by building up an
- * interrupt spec. we assume #interrupt-cells is 1, which is standard
- * for PCI. If you do different, then don't use that routine.
- */
- rc = pci_read_config_byte(pdev, PCI_INTERRUPT_PIN, &pin);
- if (rc != 0)
- return rc;
- /* No pin, exit */
- if (pin == 0)
- return -ENODEV;
-
- /* Now we walk up the PCI tree */
- lspec = pin;
- for (;;) {
- /* Get the pci_dev of our parent */
- ppdev = pdev->bus->self;
-
- /* Ouch, it's a host bridge... */
- if (ppdev == NULL) {
-#ifdef CONFIG_PPC64
- ppnode = pci_bus_to_OF_node(pdev->bus);
-#else
- struct pci_controller *host;
- host = pci_bus_to_host(pdev->bus);
- ppnode = host ? host->dn : NULL;
-#endif
- /* No node for host bridge ? give up */
- if (ppnode == NULL)
- return -EINVAL;
- } else
- /* We found a P2P bridge, check if it has a node */
- ppnode = pci_device_to_OF_node(ppdev);
-
- /* Ok, we have found a parent with a device-node, hand over to
- * the OF parsing code.
- * We build a unit address from the linux device to be used for
- * resolution. Note that we use the linux bus number which may
- * not match your firmware bus numbering.
- * Fortunately, in most cases, interrupt-map-mask doesn't include
- * the bus number as part of the matching.
- * You should still be careful about that though if you intend
- * to rely on this function (you ship a firmware that doesn't
- * create device nodes for all PCI devices).
- */
- if (ppnode)
- break;
-
- /* We can only get here if we hit a P2P bridge with no node,
- * let's do standard swizzling and try again
- */
- lspec = pci_swizzle_interrupt_pin(pdev, lspec);
- pdev = ppdev;
- }
-
- laddr[0] = (pdev->bus->number << 16)
- | (pdev->devfn << 8);
- laddr[1] = laddr[2] = 0;
- return of_irq_map_raw(ppnode, &lspec, 1, laddr, out_irq);
-}
-EXPORT_SYMBOL_GPL(of_irq_map_pci);
-#endif /* CONFIG_PCI */
void of_parse_dma_window(struct device_node *dn, const void *dma_window_prop,
unsigned long *busno, unsigned long *phys, unsigned long *size)